Yamaha | MCR-040 | Owner`s manual | Yamaha MCR-040 Owner's manual

U
MICRO COMPONENT SYSTEM
MICRO-CHAINE
OWNER’S MANUAL
MODE D’EMPLOI
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
• Explanation of Graphical Symbols
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert you to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle
is intended to alert you to the presence of important
operating and maintenance (servicing) instructions
in the literature accompanying the appliance.
1
2
3
4
5
6
7
8
9
10
11
12
IMPORTANT
Please record the serial number of this unit in the space
below.
MODEL:
Serial No.:
The serial number is located on the rear of the unit. Retain
this Owner’s Manual in a safe place for future reference.
13
14
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has
two blades and a third grounding prong. The wide blade
or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
Only use attachments/accessories specified by the
manufacturer.
Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
Unplug this apparatus during lightning storms or when
unused for long periods of time.
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to rain
or moisture, does not operate normally, or has been
dropped.
We Want You Listening For A Lifetime
Yamaha and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your
equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or
distortion – and, most importantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is
often undetectable until it is too late, Yamaha and the Electronic Industries Association’s Consumer Electronics Group
recommend you to avoid prolonged exposure from excessive volume levels.
i En
FCC INFORMATION (for US customers)
1 IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC,
to use the product.
2 IMPORTANT: When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product MUST
be used. Follow all installation instructions. Failure to
follow instructions could void your FCC authorization to
use this product in the USA.
3 NOTE: This product has been tested and found to comply
with the requirements listed in FCC Regulations, Part 15
for Class “B” digital devices. Compliance with these
requirements provides a reasonable level of assurance that
your use of this product in a residential environment will
not result in harmful interference with other electronic
devices.
This equipment generates/uses radio frequencies and,
if not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic devices.
Compliance with FCC regulations does not guarantee
that interference will not occur in all installations. If
this product is found to be the source of interference,
which can be determined by turning the unit “OFF”
and “ON”, please try to eliminate the problem by using
one of the following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch
(circuit breaker or fuse) circuits or install AC line
filter/s.
In the case of radio or TV interference, relocate/
reorient the antenna. If the antenna lead-in is 300 ohm
ribbon lead, change the lead-in to coaxial type cable.
If these corrective measures do not produce
satisfactory results, please contact the local retailer
authorized to distribute this type of product. If you can
not locate the appropriate retailer, please contact
Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe
Ave, Buena Park, CA 90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
The following information applies for MCR-140 only.
• This equipment compiles with FCC/IC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio
frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules.
This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation
(MPE). But it is desirable that it should be installed and operated with at least 20 cm and more between the radiator and person's
body (excluding extremities: hands, wrists, feet and ankles).
• This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
– Reorient or relocate the receiving antenna
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
FCC WARNING
Change or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate
the equipment.
ii En
Caution: Read this before operating your unit.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
Install this sound system in a well ventilated, cool, dry,
clean place - away from direct sunlight, heat sources,
vibration, dust, moisture, and/or cold. For proper
ventilation, allow the following minimum clearances
around CRX-040/140.
Top: 10 cm (4 in)
Rear: 10 cm (4 in)
Sides: 10 cm (4 in)
Locate this unit away from other electrical appliances,
motors, or transformers to avoid humming sounds.
Do not expose this unit to sudden temperature changes
from cold to hot, and do not locate this unit in an
environment with high humidity (i.e. a room with a
humidifier) to prevent condensation inside this unit,
which may cause an electrical shock, fire, damage to this
unit, and/or personal injury.
Avoid installing this unit where foreign object may fall
onto this unit and/or this unit may be exposed to liquid
dripping or splashing. On the top of this unit, do not
place:
– Other components, as they may cause damage and/or
discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause fire,
damage to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall and
liquid may cause electrical shock to the user and/or
damage to this unit.
Do not cover this unit with a newspaper, tablecloth,
curtain, etc. in order not to obstruct heat radiation. If the
temperature inside this unit rises, it may cause fire,
damage to this unit, and/or personal injury.
Do not plug in this unit to a wall outlet until all
connections are complete.
Do not operate this unit upside-down. It may overheat,
possibly causing damage.
Do not use force on switches, knobs and/or cords.
When disconnecting the power cable from the wall outlet,
grasp the plug; do not pull the cable.
Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
Only voltage specified on this unit must be used. Using
this unit with a higher voltage than specified is dangerous
and may cause fire, damage to this unit, and/or personal
injury. Yamaha will not be held responsible for any
damage resulting from use of this unit with a voltage
other than specified.
To prevent damage by lightning, keep the power cable
and outdoor antennas disconnected from a wall outlet or
this unit during a lightning storm.
Do not attempt to modify or fix this unit. Contact
qualified Yamaha service personnel when any service is
needed. The cabinet should never be opened for any
reasons.
When not planning to use this unit for long periods of
time (i.e. vacation), disconnect the AC power plug from
the wall outlet.
Be sure to read the “TROUBLESHOOTING” section on
common operating errors before concluding that this unit
is faulty.
iii En
17 Before moving this unit, press to set this unit to the
standby mode, and disconnect the AC power plug from
the wall outlet.
18 Condensation will form when the surrounding
temperature changes suddenly. Disconnect the power
cable from the outlet, then leave this unit alone.
19 When using this unit for a long time, this unit may
become warm. Turn the power off, then leave this unit
alone for cooling.
20 Install this unit near the AC outlet and where the AC
power plug can be reached easily.
21 The batteries shall not be exposed to excessive heat such
as sunshine, fire or the like. When you dispose of
batteries, follow your regional regulations.
22 Excessive sound pressure from earphones and
headphones can cause hearing loss.
This unit is not disconnected from the AC power source as long as
it is connected to the wall outlet, even if this unit itself is turned off
by . This state is called the standby mode. In this state, this unit is
designed to consume a very small quantity of power.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
LASER SAFETY
This unit employs a laser. Due to possible eye injury, only a
qualified service person should remove the cover or attempt to
service this device.
DANGER
This unit emits visible laser radiation when open. Avoid direct
eye exposure to beam. When this unit is plugged into the wall
outlet, do not place your eyes close to the opening of the disc tray
and other openings to look into inside.
The laser component in this product is capable of emitting radiation
exceeding the limit for Class 1.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Do not use MCR-140 within 22 cm (9 in) of persons with a heart
pacemaker implant or defibrillator implant.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to wide slot
and fully insert.
This Class B digital apparatus complies with Canadian ICES-003.
CONTENTS
PARTS ..................................................................... 2
PLAYABLE DISCS AND FILE FORMAT......... 3
CONNECTION....................................................... 4
Basic connection........................................................ 4
Wireless connection MCR-140 ........................... 5
Other connection........................................................ 5
REMOTE CONTROL ........................................... 6
FRONT PANEL DISPLAY ................................... 6
ADDITIONAL INFORMATION
TROUBLESHOOTING .......................................14
General..................................................................... 14
Radio reception........................................................ 15
iPod™ ...................................................................... 15
USB ......................................................................... 18
Disc playback .......................................................... 19
Remote control ........................................................ 19
OPERATION
FRONT PANEL AND BASIC OPERATION ..... 7
LISTENING TO MUSIC....................................... 8
OPERATION
HANDLING COMPACT DISCS ........................20
SPECIFICATIONS...............................................20
PREPARATION
PREPARATION
Playback operation..................................................... 8
Other operation .......................................................... 9
LISTENING TO FM RADIO STATIONS ........ 10
ADDITIONAL
INFORMATION
Tuning to radio stations ........................................... 10
Presetting radio stations........................................... 10
Selecting preset radio stations (Preset tuning)......... 10
USING USEFUL FUNCTIONS .......................... 11
Using setup menu .................................................... 11
Using timer and sleep timer..................................... 13
■ About this manual
• This manual describes how to operate this unit using a remote control except when it is not available. Some of these
operations are also available using the front panel buttons.
• The symbol “☞” with page number(s) indicates the corresponding reference page(s).
• Notes contain important information about safety and operating instructions. y indicates a tip for your operation.
• This manual is printed prior to production. Design and specifications are subject to change in part as a result of
improvements, etc. In case of differences between the manual and the product, the product has priority.
■ Copyright and logo marks
Advanced YST
yAired MCR-140
In 1988, Yamaha brought to the marketplace speaker systems
utilizing YST (Yamaha Active Servo Technology) to give
powerful, high quality bass reproduction. This technique uses a
direct connection between the amplifier and speaker, allowing
accurate signal transmission and precise speaker control.
As this technology uses speaker units controlled by the negative
impedance drive of the amplifier and resonance generated
between the speaker cabinet volume and port, it creates more
resonant energy (the “air woofer” concept) than the standard bass
reflex method. This allows for bass reproduction from much
smaller cabinets than was previously possible.
Real-time uncompressed music transfer without sound
degradation is realized by Yamaha original digital wireless
transfer technology, yAired. You can also control turning on/
standby and volume with the iPod by yAired.
English
1 En
PREPARATION
PARTS
Make sure you have all of the following items.
MCR-040
CD receiver
(CRX-040)
Speakers
(NS-BP80)
Dock cover
+
Cover the iPod dock when not using.
Remote control
Indoor FM antenna
MCR-140
CD receiver
(CRX-140)
Transmitter
+
Speaker cable
(1.5 m (4.9’) × 2)
■ Using the remote control
Use the remote control within 6 m (20’) of this unit and point it toward the
remote control sensor.
Notes
Within 6 m
(20’)
• Do not spill liquid on the remote control.
• Do not drop the remote control.
• Do not leave the remote control in the following places:
– hot or humid places such as a bathroom or near a heater
– extremely cold places
– dusty places
■ Replacing the battery in the remote control
Change the battery when the operation range of the remote control decreases.
Straight pin
CR2025 battery
2 En
PLAYABLE DISCS AND FILE FORMAT
■ Playable MP3 and WMA files
Use compact discs bearing the marks below.
MP3
....
Compact discs (digital audio)
Bitrate
(kbps)
Sampling
frequency
(kHz)
MPEG 1 Audio Layer-3
32-320*1
32/44.1/48
MPEG 2 Audio Layer-3, 2
8-160*1
16/22.05/24
Format
....
CD-R,CD-RW digital audio discs
• CD-R or CD-RW discs bearing one of
the following phrases.
FOR CONSUMER
FOR CONSUMER USE
FOR MUSIC USE ONLY
• Finalized CD-R or CD-RW discs
Note
*1 Variable bitrate is supported.
WMA
• Version 8
• Version 9 (Standard and variable bitrates are supported.
Professional and Lossless are not supported.)
This compact disc player may not be able to
play some CD-R/CD-RW discs or discs on
which recording was not made correctly.
....
PREPARATION
■ Playable discs
Bitrate
(kbps)
Sampling
frequency
(kHz)
High Profile
32-320*2
32/44.1/48
Mid Profile
16-32
22.05
Profile
CD-TEXT discs
*2 Both constant and variable bitrates are supported.
Notes
To play back an 8-cm (3 in) CD
Place it in the inner recessed area of the disc tray. Do not
put a normal (12-cm) CD on top of an 8-cm (3 in) CD.
To prevent a malfunction of this unit:
• Do not use any nonstandard shaped
disc (heart, etc.) available on the
market because it might damage the
unit.
• Do not use a disc with tape, stickers, or paste on it. If
you use such a disc, the disc may get stuck in the
unit, or damage to the unit may result.
• Playback for Data Disc starts in alphanumeric order of files.
• Playback for USB starts in order by date and time of creation.
• Copyright-protected WMA (DRM) files cannot be played back
by this unit.
• The disc must be ISO 9660 compatible.
• The maximum file and folder numbers are as follows.
Data Disc
USB
Maximum total number of file
and folder*3
512
9,999
Maximum folder number*3
255
255
Maximum file number per
folder
511
255
*3 The root is counted as one of the folders.
Note: Do not use any lens cleaners as they may be a
cause of malfunction.
English
3 En
CONNECTION
Basic connection
Follow the procedure below to connect the speakers and indoor FM antenna to this unit.
CAUTION
Do not connect the power cable of this unit until all cable connections are completed.
Indoor FM antenna
Notes
To the wall outlet
• The antenna should be stretched out.
• If radio reception is poor, change the height,
direction, or placement of the antenna.
• If you use an outdoor antenna instead of the
supplied FM antenna, reception will be better.
Notes
• Be sure to connect the left channel (L), right channel (R), “+”(red) “–”(black) properly. If the connections are faulty, no sound will be
heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and lacks bass.
• Do not let the bare speaker wires touch each other or do not let them touch any metal part of this unit. This could damage this unit and/
or the speakers.
• Use the supplied speakers only. Using different speakers may cause the sound to differ from the intended design.
• There is a chance that placing speakers too close to a CRT-based (Braun tube) TV set might impair picture color. Should this happen,
move the speakers away from the TV set.
4 En
CONNECTION
Wireless connection
MCR-140
Other connection
■ Stationing iPod
y
Your iPod is automatically charged when your iPod is set in the
iPod dock/charging cradle, even if the unit is in standby mode.
To turn on the unit by the playback operation of your iPod, set
POWER SAVING to NORMAL (☞ P. 11).
Station or remove your iPod whenever you want.
y
Note
Note
The volume of the unit is adjusted simultaneously with the iPod.
Be careful when controlling the volume with your iPod.
■ Group setting
To operate your iPod using transmitter, you need to match
the wireless group between the transmitter and the CD
receiver (CRX-140). The default setting for both the
transmitter and the CD receiver is A2.
PREPARATION
Playback operation with your iPod connected to the
transmitter turns the unit on automatically, and you can
enjoy the music in your iPod.
The unit is compatible with iPod (5th generation), iPod classic,
iPod nano, and iPod touch.
MCR-040
Dock Adapter
iPod dock
GROUP A1
GROUP A2
Note
GROUP B3
To secure the connection, attach a compatible Dock Adapter
supplied with the iPod or an iPod Universal Dock Adapter
(sold separately), and remove the protective case covering
your iPod.
To select wireless group of the CD receiver
(CRX-140)
1
2
MCR-140
Station your iPod in the charging cradle when you want to charge
your iPod. You can also control your iPod with the remote control
when your iPod is in the charging cradle.
Press SETUP.
Select WIRELESS SET
menu.
3
4
Transmitter
Charging
cradle
Confirm with ENTER.
Select the group.
■ Connecting USB
Connect or remove your USB device whenever you want.
5
Complete the setting.
6
Exit setup menu.
■ Wireless connection to Subwoofer
You can use a subwoofer wirelessly with the wireless
subwoofer kit (SWK-W10, etc., sold separately). To
establish the wireless connection, set WIRELESS SW to
YES (☞ P. 11). For details, refer to the owner’s manual
of SWK-W10.
y
USB device is automatically charged when it is connected to the
unit, even if the unit is in standby mode.
Notes
5 En
English
• This unit supports USB mass storage class devices (e.g., flash
memories or portable audio players) using FAT16 or FAT32
format.
• Do not connect devices other than USB mass storage class
devices (such as USB chargers or USB hubs), PCs, card
readers, an external HDD, etc.
REMOTE CONTROL
1 Infrared signal transmitter (☞ P. 2)
2
: standby/on
3 Source buttons: PORTABLE, CD, iPod, USB, TUNER (☞ P. 8, 10)
4 FM control buttons (☞ P. 10)
5
/ : iPod scroll buttons (☞ P. 8)
MENU/ENTER/
/
/
: multi function buttons (☞ P. 8, 9, 10, 11)
: Stop button (☞ P. 8, 9)
6 FOLDER T/S (☞ P. 8)
7 SETUP (☞ P. 5, 11)
8 SHUFFLE/REPEAT (☞ P. 9)
9 DISPLAY (☞ P. 9, 12)
0 TIMER (☞ P. 12, 13)
A SLEEP (☞ P. 13)
B Battery insulation sheet: Remove before using.
C Volume control buttons: Press to control the volume.
Press MUTE to turn off the sound. Press again to resume the volume.
FRONT PANEL DISPLAY
1 SLEEP indicator: Lights up when the sleep timer is on
(☞ P. 13).
8 Multi information display: Shows the various information
such as the tuning frequency.
2 PRESET indicator: Lights up when you preset radio
stations (☞ P. 10).
9 TIMER indicator: Flashes during timer setting. Lights up
when the timer is on (☞ P. 13).
3 STEREO indicator: Lights up when this unit is receiving a
strong signal from an FM stereo broadcast.
0 TUNED indicator: Lights up when this unit is tuned into a
station (☞ P. 10).
4 AUTO indicator: Lights up when this unit is in the
Automatic Tuning mode (☞ P. 10).
A MEMORY indicator: Flashes when searching for a radio
station by automatic preset tuning. Lights up when you preset
radio stations automatically or manually (☞ P. 10).
5 SHUFFLE indicator: Lights up when you set your
iPod (MCR-040)/CD/USB to shuffle play (☞ P. 9).
6 REPEAT indicator: Lights up when you set your
iPod (MCR-040)/CD/USB to repeat play (☞ P. 9).
7 MUTE indicator: Lights up when the sound is muted.
6 En
B Multi information indicator: Indicates the music information
currently displayed on Multi information display (☞ P. 9).
C Operation indicators: Shows operable multi function
buttons for a currently selected SETUP item.
OPERATION
FRONT PANEL AND BASIC OPERATION
y
• This unit has an automatic standby function, which will automatically switch the unit to standby mode if the unit is left turned on for
1 hour without playback or any other operation being performed. This function is not available when the source is set to PORTABLE/
FM.
• Press to set the unit to standby mode. All the information on the front panel display is not displayed in standby mode. This can
reduce power consumption. To turn on the unit, press /
, or start playback with your iPod connected to the transmitter (MCR-140
only).
• If the iPod selected as the input source is disconnected from the transmitter, or does not output sound for a certain period, the unit will
automatically switch to standby mode (MCR-140 only).
OPERATION
MCR-140
MCR-040
iPod dock
Charging cradle
iPod
:
Unit standby/on
Disc tray
:
Disc tray open/close
VOLUME
INPUT
USB
PORTABLE
:
Play/pause playback
:
Stop playback
USB port:
☞ P. 5, 8
INPUT button:
Press repeatedly to choose the input source.
3.5 mm stereo mini
plug cable
VOLUME
Down
Up
PORTABLE:
:
Connecting headphones
Press the INPUT button repeatedly
to select PORTABLE. Then start
playback on the connected portable
audio device.
English
No sound is output from the speakers
when headphones are connected.
7 En
LISTENING TO MUSIC
Playback operation
Follow the procedures below to play back music.
1 Set the source
2 Switch the
input
3 Select music and start playback
Scroll the list
MCR-040
Dock Adapter
Control menu
For the MCR-140, the operation on the remote
control or front panel is available only when your
iPod is stationed in the charging cradle (☞ P. 5).
☞ P. 5
iPod*1
MCR-140
MCR-140
Status indicator
☞ P. 5, 16
Control with iPod
Be careful when controlling the volume (☞ P. 5).
CD
Skip to the first file in the
previous/next folder for MP3 or
WMA*3
USB*2
☞ P. 5
*1 Some features may not be available depending on the model or the software version of your iPod.
*2 · Some devices may not work properly even if they meet the requirements.
· Playability of and power supply to all kind of USB devices are not guaranteed.
· The reading time may exceed 30 seconds depending on the number of files/folders.
· Yamaha and suppliers accept no liability for the loss of data saved on the USB devices connected to this unit.
As a precaution, it is recommended that the files are made backup copies.
*3 If you press these buttons during playback, the folder name is displayed on the front panel display for a certain period.
8 En
LISTENING TO MUSIC
Other operation
■ Control playback
1
■ Switching the display
2
You can switch the playback information shown on the
front panel display. Some special characters may not be
shown properly.
1
2
During playback
During playback
Press repeatedly.
OPERATION
: Skip forward/Press and hold to Fast forward
: Skip backward/Press and hold to Rewind
: Play/Pause
: Stop
For iPod MCR-040
Song number and elapsed time (default setting)
↓
Notes
Song number and remaining time
• Playback for Data Disc starts in alphanumeric order of files.
• Playback for USB starts in order by date and time of creation.
↓
Song name
↓
■ Shuffle play
Artist name
You can play back in random sequence.
↓
Album name
↓
Press repeatedly.
Back to the default setting
Note
For iPod
*1 You cannot set ALBUMS when you use an iPod touch.
For CD/USB
This function is available for iPod (5th generation), iPod classic,
iPod nano, and iPod touch. However, even with these models,
this function may not be available depending on the software
version of your iPod.
For CD/USB
Track/file number and elapsed time of the current
song (default setting)
*2 If the audio format of the selected music source is MP3/
WMA, you can also select FOLDER.
↓
■ Repeat play
↓
You can play back repeatedly.
Total time of the disc*4
Track number and remaining time of the current
song*4
↓
Remaining time of the disc*4
Press repeatedly.
↓
File name*5
↓
Track name*6
↓
*3 If the audio format of the selected music source is MP3/
WMA, you can also select FOLDER.
Artist name*6
↓
Album name*6
↓
English
Back to the default setting
*4 Only for Audio CDs
*5 Only for MP3/WMA files
*6 Only when the selected track has information
9 En
LISTENING TO FM RADIO STATIONS
Tuning to radio stations
1
2
Press TUNER.
Press and hold.
Automatic tuning starts.
y
If the signal received from the station you want to select is weak,
you can also tune into radio stations manually by pressing
TUNING<</>> repeatedly.
Note
If you tune to a station manually, the sound is monaural.
Presetting radio stations
You can store your favorite FM stations with the preset
function.
■ Automatic preset tuning
1
2
Press and hold
MEMORY for more than
2 seconds in FM mode.
Start the automatic preset.
Note
When you perform the automatic preset, all stored stations are
cleared and the new stations are stored.
■ Manual preset tuning
1
2
Tune into a favorite
radio station.
3
Press MEMORY.
4
Select the preset
number you want to
store to.
Complete the
manual preset.
y
• You can preset up to 30 FM stations.
• To cancel the manual preset while choosing a preset number,
press MEMORY again.
• You can delete a preset station by pressing SETUP → MENU
S/T → ENTER to select PRESET DELETE.
10 En
Selecting preset radio stations
(Preset tuning)
Select the preset radio station
in FM mode.
USING USEFUL FUNCTIONS
Using setup menu
The setup menu appears on the front panel display by pressing SETUP. You can set various useful functions with setup
menu.
Setup menu
Parameter or control range
Reference page
(Displays only when the input source is set to FM.)
10
DIMMER
DIMMER ON (25%)/OFF (100%)
below
TREBLE
–6 dB to +6 dB
below
BASS
–6 dB to +6 dB
below
BALANCE
L+5 - CENTER - R+5
below
CLOCK SET
Hour, minute
12
TIMER SET
Time (hour, minute), running time, sound (source, track or preset
number), timer on/off
12
WIRELESS SET MCR-140
GROUP A1/A2/A3/B1/B2/B3
5
POWER SAVING MCR-140
NORMAL/ECO
below
WIRELESS SW MCR-140
NO/YES
below
1
2
Press SETUP.
3
Select desired
setup menu.
4
Confirm with
ENTER.
Change the settings.
5
OPERATION
PRESET DELETE
6
Complete the
setting.*2
Exit setup
menu.
Repeat*1
*1 When there are some parameters to set, repeat steps 3 and 4. You can go back to a previous parameter by pressing
*2 To set additional items, repeat steps 2 to 5.
.
y
To cancel the setting during the operation, press SETUP.
■ Setting dimmer, tone/balance and power saving mode
DIMMER: Changes the brightness of the front panel display.
TREBLE*3: Adjusts the high frequency response.
BASS*3: Adjusts the low frequency response.
BALANCE: Adjusts the volume level of each left and right speaker channel.
POWER SAVING: If you set to ECO, you can reduce standby power consumption. However, you cannot turn on the
unit by playback operation on your iPod during standby mode. The default setting is NORMAL. This function is
available only for MCR-140.
WIRELESS SW: Set to YES when you use a subwoofer via the wireless subwoofer kit (SWK-W10, etc., sold
separately). The default setting is NO. This function is available only for MCR-140.
*3 Also effective when you are using headphones.
English
11 En
USING USEFUL FUNCTIONS
■ Adjusting the clock
CLOCK SET: To set hour and minute, repeat steps 3 and 4 on page 11.
y
The current time appears on the front panel display for a certain period by pressing and holding DISPLAY if the time setting has
completed.
Note
The time setting is lost once the power cable is disconnected from the wall outlet.
■ Setting the timer
TIMER SET: To select the following setting items, repeat steps 3 and 4 on page 11.
y
You can enter TIMER SET directly by pressing and holding TIMER.
Time (hour and minute)
Running time
You can choose the running time from 10 minutes to 90 minutes in 10 minute increments.
“– –” means the unit will not be set to standby mode automatically.
Input source and track/file number or preset number
Notes
• If the source is not set properly, the timer sound will not be heard. Make sure that the source is set securely.
• MCR-140: When you select an iPod as the input source, you need to set the iPod in the charging cradle on the unit.
iPod:
When you select the iPod as a source, this unit resumes the music that you were listening to last time.
CD:
Set a track/file number.
If you set the track/file number which is not exist, the first track/file is played back automatically.
USB:
Set a file number.
If you set a file number that does not exist, the first file is played back automatically.
FM:
Set preset number.
By selecting “– –”, the FM station you set last time is set.
Timer ON/OFF
Switch the timer on/off. When the timer is on, the TIMER indicator lights up on the front panel display
(☞ P. 6).
y
This setting is also available with TIMER (☞ P. 6, 13).
12 En
USING USEFUL FUNCTIONS
Using timer and sleep timer
■ Using the timer
The timer sets the unit to play back music at the time you set. The unit is set to standby mode after the specified running
time elapses.
To use the timer, set the appropriate input source securely and set the timer in the setup menu in advance (☞ P. 12).
1
2
Adjust the volume level.
Each time you press TIMER while the power is on, it switches on/off. When you switch on the timer, the TIMER
indicator lights up on the front panel display (☞ P. 6). To turn on the unit via the timer, set this unit to standby mode
when the timer is switched on.
OPERATION
Press TIMER.
Notes
• The clock has to be set in advance.
• When the unit is in standby mode, the TIMER indicator does not light up on the front panel display even if the timer is on.
• After the unit is operated via the timer, the timer function switches off.
y
• To activate the timer function again, press TIMER while the power is on.
• The timer setting is saved for convenient use next time.
■ Using sleep timer
The sleep timer sets the unit to the standby mode after the specified time elapses.
Press repeatedly.
The SLEEP indicator lights up on the front panel display (☞ P. 6).
English
13 En
ADDITIONAL INFORMATION
TROUBLESHOOTING
Refer to the table below when this unit does not function properly. If the problem you are experiencing is not listed below
or if the instruction below does not help, turn off this unit, disconnect the power cable, and contact the nearest authorized
Yamaha dealer or service center.
General
Problem
This unit fails to turn
on or enters the
standby mode soon
after the power is
turned on.
Cause
Remedy
page
The power cable is not connected or the
plug is not completely inserted.
Connect the power cable firmly.
4
This unit has been exposed to a strong
external electric shock (such as lightning
or strong static electricity).
Set this unit to the standby mode, disconnect the
power cable, plug it back in after 30 seconds and
then use it normally.
—
No appropriate input source has been
selected.
Select an appropriate input source with INPUT on
the front panel (or the source buttons on the remote
control).
—
Speaker connections are not secure.
Secure the connections.
4
The mute function may be on.
Cancel the mute function.
6
The volume is turned down.
Turn up the volume.
—
Signals this unit cannot reproduce are
being input from a source component,
such as a CD-ROM.
Play a source whose signals can be reproduced by
this unit.
3
The sleep timer may be set.
This is not malfunction. Turn on the unit and play the
source again.
—
The unit does not
operate properly.
No sound.
The power is
suddenly turned off.
The unit is left turned on for 1 hour
without playback or any other operation
being performed.
The power was turned on by the timer
and elapsed specified running time.
MCR-140: The iPod selected as the input
source is disconnected from the
transmitter, or does not output sound for a
certain period.
The clock setting has
been cleared.
The power cable has been disconnected.
Connect the power cable, and set the clock again.
—
Sound is heard from
the speaker on one
side only.
Incorrect cable connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
4
There is noise
interference from
digital or radio
frequency
equipment.
This unit is too close to the digital or
high-frequency equipment.
Move this unit farther away from such equipment.
—
14 En
TROUBLESHOOTING
The following status messages appear only if you are using MCR-140.
Status message
Cause
SubWoofer Link
Wireless connection between the
subwoofer and the unit is established.
SubWooferUnlink
Wireless connection between the
subwoofer and the unit is disconnected.
Wireless Error
There is a problem with the internal
circuit of this unit.
Remedy
Disconnect the power cable and contact the nearest
authorized Yamaha dealer or service center.
page
—
Radio reception
Problem
FM stereo reception is
noisy.
Cause
Remedy
page
Check the antenna connections.
4
The characteristics of FM stereo
broadcasts may cause this problem
when the transmitter is too far away or
the antenna input is poor.
Try using a high-quality directional FM antenna.
—
Use the manual tuning method.
10
The desired station
cannot be tuned into
with the automatic
tuning method.
The signal is too weak.
Use a high-quality directional FM antenna.
—
Use the manual tuning method.
10
The preset selecting
function does not
work.
The preset (memory) may have been
erased.
Preset radio stations again.
10
There is distortion,
and clear reception
cannot be obtained
even with a good FM
antenna or an outdoor
antenna.
Multipath reflection or other radio
interference may have occurred.
Change the height, direction, or placement of the
antenna.
—
ADDITIONAL
INFORMATION
The antenna is connected improperly.
iPod™
Note
In case of a transmission error without a status message appearing in the front panel of this unit, check the connection to your iPod (see
page 5).
The following status messages appear only if you are using MCR-040.
Status message
Remedy
page
This unit is in the middle of recognizing
the connection with your iPod.
If the message continues to appear in the front panel
display and playback does not start, connect the iPod
again.
—
Unknown iPod
There is a problem with the signal path
from your iPod to this unit.
Connect the iPod again.
5
The iPod being used is not supported by
this unit.
Only iPod (5th generation), iPod classic, iPod nano,
and iPod touch are supported.
—
Station your iPod back in the iPod dock.
5
iPod
This unit has recognized your iPod;
however, it cannot obtain information
such as elapsed time.
iPod Unplugged
Your iPod was removed from the iPod
dock.
15 En
English
Cause
iPod Connecting
iPod Charging
TROUBLESHOOTING
The following status messages appear only if you are using MCR-140.
Status message
Cause
Remedy
page
iPod Linked
iPod
Wireless connection was successful.
iPod Unlinked
Wireless connection has disconnected.
Connect the iPod to the transmitter and start
playback.
5
iPod Low Batt.
The battery of the iPod is getting flat.
Set it in the charging cradle.
5
The following LED statuses of the status indicator refer to the transmitter.
LED status
Off
Transmitter status
Remedy
page
The transmitter is in standby mode.
An iPod is not connected or wireless
communication has not been established.
Flashes green
Connection in progress.
Flashes green once
Adjusting the volume level or operating
with the remote control.
Lights up green
Wireless communication between the
unit and transmitter is established.
Lights up green and
flashes red for 2
seconds
Please wait.
—
An unsupported iPod is connected.
Only iPod (5th generation), iPod classic, iPod nano,
and iPod touch are supported.
5
Lights up green and
keeps flashing red
Connection failed.
Connect again.
8
Flashes red
Error occurs.
Remove the iPod from the transmitter, and connect
again.
8
Flashes red once
The volume of the unit is set to maximum
or minimum.
Flashes red 2 times
continuously
(regardless of green
status)
The battery of the iPod is low.
Set the iPod in the charging cradle.
5
16 En
TROUBLESHOOTING
Problem
No sound.
Cause
Remedy
page
Connect the power cable correctly.
—
The iPod software version has not been
updated.
Download the latest iTunes software to update the
iPod software version to the latest.
—
The iPod is in the process of connecting
with the unit.
Please wait for a while.
—
MCR-140: The battery of the iPod is low.
Charge the iPod.
—
MCR-140: The iPod is not connected to
the transmitter firmly.
Connect the iPod firmly.
—
MCR-140: Earphones are connected to
the iPod.
Remove the earphones.
—
MCR-140: The signal from the
transmitter is blocked by your body or
metallic objects, etc.
Change the way of holding, the orientation, or the
position of the transmitter to avoid your body or
metallic objects blocking the signal.
—
MCR-140: There is a device (microwave
oven, wireless LAN, cordless telephone,
etc.) outputting signals in the 2.4 GHz
frequency band nearby.
Place the unit away from these devices, or turn them
off. If the device is IEEE802.11n-compliant, change
the channel setting of the device so as not to affect
the unit.
—
MCR-140: Distance is too far.
Move the transmitter closer to the unit. Transmission
range is approximately 10 m (32.8 ft). Also, placing
the unit in a lower position makes it easier to receive
wireless signals.
—
MCR-140: The unit and transmitter are
not connected since they are set to
different groups.
Set both the unit and transmitter to the same group.
5
MCR-140: The unit is connected to
another unit.
Select a different group by changing the group
setting of the unit and transmitter.
5
MCR-040: The iPod is set in the iPod
dock improperly.
Remove the iPod from the unit, then set it in the iPod
dock again.
5
MCR-140: The iPod is not connected to
the transmitter properly.
Remove the iPod from the transmitter, then set it to
the transmitter again.
5
The iPod is not supported by this unit.
Only iPod (5th generation), iPod classic, iPod nano,
and iPod touch are supported.
5
The iPod is not connected correctly.
Connect the iPod firmly.
—
The iPod software version is out of date.
Update the iPod software version to the latest. If the
problem cannot be solved, even with the latest
software, reset the iPod.
—
MCR-040: The iPod is set in the iPod
dock improperly.
Remove the iPod from the unit, then set it in the iPod
dock again.
5
MCR-140: The iPod is connected to the
transmitter improperly.
Remove the iPod from the transmitter, and connect
to the transmitter again, then start playback.
8
The playback
information is not
displayed on the
front panel display.
The iPod you set is not compatible with
the playback information display.
Only iPod (5th generation), iPod classic, iPod nano,
and iPod touch are supported.
5
You are using MCR-140.
Only MCR-040 is available for playback information
display.
—
The iPod does not
charge up.
MCR-040: The iPod is set in the iPod
dock improperly.
Remove the iPod from the unit, then set it in the iPod
dock again.
5
MCR-140: The iPod is set in the charging
cradle improperly.
Remove the iPod from the unit, then set it in the
charging cradle again.
5
No sound.
The iPod sounds, but
you cannot operate it
with the unit or the
remote control.
Cannot change the
volume by changing
the volume of the
iPod.
The iPod display
does not change by
pressing the remote
control volume keys.
ADDITIONAL
INFORMATION
The power of the unit is off.
The unit cannot be
operated by the
remote control.
You cannot operate
from the iPod.
English
17 En
TROUBLESHOOTING
Problem
Cause
Remedy
page
Suddenly the
speaker produces
sound even though
an iPod is not
connected.
MCR-140: The unit is connected to
another transmitter.
Change the group setting.
5
Transmitted sound is
cut.
MCR-140: If noise occurs at the same
frequency the transmitter is using, the
unit will search and move to another
(unused) frequency, which may cause
sound to be cut.
This is not malfunction. If cut occurs frequently,
relocate the unit.
—
USB
Note
In case of a transmission error without a status message appearing in the front panel of this unit, check the connection to the USB device
(see page 5).
Status message
Cause
Remedy
page
USB Unplugged
The USB device is not connected
firmly.
Connect the USB device again.
5
Unknown USB
The connected USB device is not
playable on this unit.
Connect playable USB device.
5
USB OverCurrent
The connected USB device is not
playable on this unit.
Disconnect the USB device. Change input source
other than USB and select USB as input source
again. Then connect playable USB device again.
5
The USB device is connected at an
angle.
Problem
MP3/WMA file in the
USB device does not
play.
18 En
Cause
Remedy
page
The USB device is not recognized.
Connect the USB device again.
5
Connect an AC adapter if supplied with the device.
—
Improper USB device connections.
Connect the USB device again.
5
The MP3 or WMA formats are not
compatible with this unit.
Replace the file with a correctly recorded file
playable with this unit.
3
If the solutions above do not resolve the
problem, the USB device is not playable
on the unit.
Try another USB device.
—
TROUBLESHOOTING
Disc playback
Problem
Cause
Remedy
page
The sampling rate of an MP3 or WMA
file may not be compatible with this unit.
Check the sampling rate and bit rate of an MP3 or
WMA file are compatible with this unit.
3
Disc playback does
not start.
You may be using a CD-R/RW that is not
finalized.
Finalize the CD-R/RW.
—
The disc label may be upside down.
Check that the disc label is facing up.
—
The disc may be defective.
Try playing back another disc. If this cures the
problem, the disc you want to play back is defective.
—
MP3/WMA disc may not contain
sufficient music files to be played back.
Check that your MP3/WMA disc contains at least
5 MP3/WMA music files. If the number of files is
small, the disc may not be recognized.
—
The sampling rate of an MP3 or WMA
file may not be compatible with this unit.
Check the sampling rate and bit rate of an MP3 or
WMA file are compatible with this unit.
3
Some button
operations do not
work.
The disc loaded into the unit may not be
compatible.
Remove the disc and then check whether the unit
supports the disc or not.
3
Playback does not
start immediately
after pressing
on the unit or
on
the remote control.
The disc may be dirty.
Wipe the disc clean.
—
The disc loaded into the unit may not be
compatible.
Use a disc supported by the unit.
3
If the unit was moved from a cold to
warm place, condensation may have
formed on the disc reading lens.
Wait for an hour or two until the unit adjusts to the
room temperature, and try again.
—
“No Disc” appears in
the display even
though a disc is in
the disc tray.
The disc loaded into the unit may not be
compatible.
Use a disc supported by the unit.
3
The disc may be dirty.
Remove the disc and then wipe the disc clean.
—
Disc is loaded upside-down.
Remove the disc and then load the disc with the
labeled side facing up.
—
ADDITIONAL
INFORMATION
No sound or
distorted sound
Remote control
Problem
The remote control
does not work nor
function properly.
Cause
Remedy
page
The remote control may be operated
outside its operation range.
For information on the remote control operation
range, refer to “Using the remote control”.
2
The remote control sensor on this unit
may be exposed to direct sunlight or
lighting.
Change the lighting or orientation of this unit.
—
The battery may be worn out.
Replace the battery with new one.
2
There are obstacles between the sensor of
this unit and the remote control.
Remove the obstacles.
—
English
19 En
HANDLING COMPACT DISCS
• Always handle with care so that the playing surface is
not scratched. Do not bend discs.
• Do not wipe with a circular motion; wipe straight
outward from the center.
• To keep the playing surface clean, wipe with a clean,
dry cloth. Do not use any type of disc cleaner, spray, or
any other chemical-based liquid.
• Do not expose discs to direct sunlight, high temperature
or high humidity for a long time.
• Use a soft-tipped pen when writing on the label side of a
disc.
SPECIFICATIONS
■ CD RECEIVER (CRX-040, CRX-140)
PLAYER SECTION
iPod
• Supported iPod ...... iPod (5th generation), iPod classic, iPod nano,
iPod touch
CD
• Media ......................................................................CD, CD-R/RW
• Audio format .............................................Audio CD, MP3, WMA
LASER
• Type ....................................... Semiconductor laser GaAs/GaAlAs
• Wave length ........................................................................ 780 nm
• Output power....................................................................... 10 mW
USB
• Audio format ............................................................... MP3, WMA
PORTABLE
• Input connector........... STEREO L/R: 3.5 mm STEREO mini Jack
AMPLIFIER SECTION
• Maximum output power............................................ 15 W + 15 W
(6 Ω 1 kHz, 10% THD)
• Input sensitivity
PORTABLE ............................................................ 450 mV/22 kΩ
• Total harmonic distortion
CD etc. 1 kHz/1W ................................................................ 0.05 %
TUNER SECTION
• Tuning range
[U.S.A. and Canada models].......................... 87.5 to 107.9 MHz
[Other models] ........................................... 87.50 to 108.00 MHz
GENERAL
• Power supply
[Europe model] ................................................ AC 230 V, 50 Hz
[U.S.A. and Canada models]............................ AC 120 V, 60 Hz
[Asia model]..................................AC 220/230-240 V, 50/60 Hz
[Taiwan model] ......................................... AC 110/120 V, 60 Hz
[Australia model] ............................................. AC 240 V, 50 Hz
[U.K. model] .................................................... AC 230 V, 50 Hz
[China model] .................................................. AC 220 V, 50 Hz
[Korea model] .................................................. AC 220 V, 60 Hz
• Power consumption................................................................ 25 W
20 En
• Standby power consumption
MCR-040 .................................................................0.5 W or less
MCR-140
POWER SAVING: ECO ......................................1.0 W or less
POWER SAVING: NORMAL (default setting)
..............................................................................2.0 W or less
• Dimensions (W × H × D) .............................. 180 × 120 × 309 mm
(7 1/8 × 4 3/4 × 12 1/8 in)
• Weight ................................................................... 3.6 kg (7.9 lbs.)
■ SPEAKER (NS-BP80)
• Driver unit ................................. 10 cm (4 in) full-range Cone type
/Non Magnetic Shielding Type
• Dimensions (W × H × D) .............................. 122 × 118 × 287 mm
(4 3/4 × 4 5/8 × 11 1/4 in)
• Weight ................................................................... 1.4 kg (3.1 lbs.)
■ TRANSMITTER (YIT-W11TX)
• Frequency .......................................................................... 2.4 GHz
• Transmission range..................................... Approx. 10 m (32.8 ft)
(without interference)
• Number of units which can be simultaneously transmitted to
............................. Up to 7 units (depending on the circumstances)
Specifications are subject to change without notice.
iPod™
iPod is a trademark of Apple Inc., registered in the U.S. and other
countries.
“Made for iPod” means that an electronic accessory has been
designed to connect specifically to iPod and has been certified by
the developer to meet Apple performance standards.
Apple is not responsible for the operation of this device or its
compliance with safety and regulatory standards.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
AVERTISSEMENT
L’utilisation de commandes et l’emploi de réglages ou de
méthodes autres que ceux décrits ci-dessous, peuvent
entraîner une exposition à un rayonnement dangereux.
● The label is located on the bottom of the unit. (U.S.A and
Canada models only)
● L’étiquette est situé sur la base de l’unité (États-Unis et le
Canada modèles seulement).
(Traduction française)
DANGER :
ÉVITER UNE EXPOSITION DIRECTE AU
RAYON
RADIATION LASER INVISIBLE QUAND
L’APPAREIL EST OUVERT
ATTENTION : NE PAS REGARDER FIXEMENT LE
FAISCEAU
RADIATION LASER INVISIBLE QUAND
L’APPAREIL EST OUVERT
Printed in China
WS48490
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising