Prestige 661H Series

ADSL 2+ Security Gateway

Prestige 661HW Series

802.11g Wireless ADSL 2+ Gateway

Quick Start Guide

Version 3.40

3/2005

Prestige 661H/HW Series Quick Start Guide

Overview

The Prestige 661H (P-661H) and Prestige 661HW (P-661HW) are ADSL routers with a built-in switch. The

Prestige 661HW also has IEEE 802.11g wireless capability. All wireless features pertain to the P-661HW series only.

You may need your Internet access information.

See your User’s Guide for background information on all features.

This guide is divided into the following sections.

1 Hardware Connections

2 Configuration for Internet Access

3 Wireless Configuration (P-661HW)

4 NAT

5 Firewall

6 TMSS

7 Troubleshooting

1 Hardware Connections

You need the following before you start.

Prestige Computer(s) Ethernet Cable Telephone Cable Power Adaptor

If you prefer to see a multi-media animation of how to make hardware connections, see the included CD.

2

Prestige 661H/HW Series Quick Start Guide

1 DSL: Connect the Prestige to a telephone jack using a telephone wire.

2 LAN: Use an Ethernet cable to connect a computer to a LAN 10/100M port for initial configuration and/or

Internet access.

3 POWER: Use the included power adaptor to connect the POWER socket to an appropriate power source

(see the User’s Guide for power adaptors specifications by region).

After you’ve made the connections, push in the power button to turn on the Prestige. Look at the front panel

LEDs. The PWR/SYS LED blinks while performing system testing. The PWR/SYS and/or WLAN LEDs then turn steady on if the testing is successful. The LAN LEDs turn on if the (corresponding) LAN ports are properly connected.

2 Configuration for Internet Access

You may configure the Prestige for Internet access in any one of these ways:

• Configuration Genie

• Zero Configuration

• Web Configurator Internet Access Wizard

3

Prestige 661H/HW Series Quick Start Guide

2.1 Configuration Genie

From the included CD, click “Multimedia Auto Provisioner” (the installation and configuration assistant) and then click “Installation Tutorial”. After you’ve viewed the tutorial, click “Configuration Genie” at the end of the installation tutorial or from “Multimedia Auto Provisioner” in the CD.

2.2 Zero Configuration

Launch your web browser and navigate to any web site (for example, www.zyxel.com). The

Prestige automatically detects and configures your Internet connection. This may take about two minutes.

If you have a PPPoE or PPPoA connection, a screen displays prompting you to enter your

Internet account information. Enter the username, password and/or service name exactly as provided. Click

Apply.

Note: Configuration Genie or Zero Configuration are only able to configure the device automatically for

Internet access if you are using PPPoE, PPPoA or ENET ENCAP encapsulation with a dynamically-assigned IP address from your ISP.

If you’re not using these Internet access settings, then use the Web Configurator Internet

Access Wizard to manually configure the device.

2.3 Accessing the Web Configurator

1 Launch your web browser. Enter

“192.168.1.1” as the web site address.

4

Prestige 661H/HW Series Quick Start Guide

Note: If you do not see the next screen, then please read

Section 7.1 on page 12

2 Click Login. 3 Type a new password

(retype it to confirm) and click Apply.

Otherwise click

Ignore. You then see the main web configurator screen

4 In the MAIN MENU screen, click WIZARD SETUP.

2.3.1 Internet Access Setup

Note: Enter the Internet access information given to you by your ISP exactly in each wizard screen and then click Next to continue or click Back to return to the previous screen.

Screen information is not saved when you click Back.

5

Prestige 661H/HW Series Quick Start Guide

1 From the Mode drop-down list box, select Routing (default) if you want to use routing features such as

NAT.

2 The next wizard screen varies depending on the Encapsulation you chose in the first wizard screen. From the Network Address Translation drop-down list box, select SUA Only if you have one public IP address,

Full Feature if you have more than one public IP address (for translation) or None to disable NAT.

• PPPoE.

• ENET

ENCAP

Select Connect

on Demand when you don't want the connection up all the time and specify an idle time-out period

(in seconds) in the Max. Idle

Timeout field.

Select Nailed-

Up Connection when you want your connection up all the time. The Prestige will try to bring up the connection automatically if it is disconnected.

6

Prestige 661H/HW Series Quick Start Guide

Note: You will only see the next two screens in Routing mode.

• PPPoA • RFC1483

3 Verify your

LAN and

WAN settings.

To change the

LAN settings, click Change

LAN

Configuration; otherwise click

Save Settings to save the configuration and go to the final wizard screen.If you change the

Prestige’s LAN IP address, you must use the new IP address if you want to access the web configurator again.

4 Click Save Settings in the screen shown in step

3 to go to the final wizard screen.The Prestige automatically tests the connection to the computer(s) connected to the LAN ports. To test the connection from the Prestige to the ISP, click

Start Diagnose. Otherwise click Return to Main

Menu to go back to the main screen.

3 Wireless Configuration

(P-661HW series only)

WPA-PSK encryption is preferred to WEP because it has user authentication and improved data encryption. If you don’t have WPA-capable wireless clients, configure WEP encryption.

7

Prestige 661H/HW Series Quick Start Guide

Note: Wireless clients and the Prestige must use the same SSID, channel ID, WEP or WPA-PSK key (if enabled).

1 Click the Wireless LAN link under

Advanced Setup.

2 Click 802.1x/WPA.

Select

Authentication

Required, then select WPA-

PSK and then type a Pre-

shared Key.

3 Click Advanced Setup, Wireless LAN, Wireless. In the ESSID field, enter up to 32 printable characters to uniquely identify the Prestige. If you didn’t configure WPA-PSK, configure WEP in this screen (not visible if you’ve configured WPA-PSK).

8

Prestige 661H/HW Series Quick Start Guide

3.1 OTIST

Configure this screen only if you have OTIST-aware wireless clients. OTIST (One-Touch Intelligent Security

Technology) allows you to transfer your Prestige’s SSID and WEP or WPA-PSK security settings to wireless clients that support OTIST and are within transmission range. You can also choose to have OTIST generate a WPA-PSK key for you if you didn’t configure one manually.

Click Advanced Setup, Wireless LAN and then click OTIST. To change the Setup key enter up to eight printable characters. To have OTIST automatically generate a WPA-PSK key select the Yes check box. If you manually configured a WEP key or a WPA-PSK key and you also selected this check box, then the key you manually configured is used.

Note: The AP and wireless client(s) MUST use the same Setup key .

In each wireless client ZyXEL utility, click the Adapter tab. Select the OTIST check box, enter the same

Setup Key as your Prestige’s and click Save.

Note: You must click Start in the Prestige OTIST web configurator screen and in the wireless client(s)

Adapter screen all within three minutes (at the time or writing). You can start OTIST in the wireless clients and Prestige in any order but they must all be within range and with OTIST enabled.

9

Prestige 661H/HW Series Quick Start Guide

4 NAT

NAT (Network Address Translation - NAT, RFC 1631) means the translation of an IP address in one network to a different IP address in another. For example, you could translate one public IP address to multiple private IP addresses on your LAN (SUA Only).

Click

Advanced

Setup and then NAT to open the

NAT-Mode screen.

Select SUA

Only if you have one public IP address and Full Feature if you have multiple public IP addresses (for address translation).

If you have servers on your

LAN, configure an SUA server set to have them visible to the outside.

From the NAT -

Mode screen click Edit

Details and fill in the fields as shown.

5 Firewall

The firewall is already enabled by default on the Prestige.

Click Advanced Setup and then Firewall to open the firewall screen. The firewall protects your LAN from attacks from the Internet. No traffic can enter your LAN unless a request was generated on the LAN first.

Click Default

Policy to see rule direction information.

You can also disable the firewall here if you want.

10

Prestige 661H/HW Series Quick Start Guide

6 TMSS

TMSS (Trend Micro Security Services) scans computers behind the Prestige for potential vulnerabilities such as spyware, missing security patches, trojans etc. and then tells you how to update the computer so as to fix the vulnerability.

1 TMSS is enabled by default on the Prestige, so you should see the following screen after you launch your web browser to connect to the

Internet via the Prestige for the first time. If you don’t see this screen, then enter http:// tmss.trendmicro.com as the URL. Click Continue to go to the Active X control installation page.

2 Download the ActiveX control to view the TMSS web page. The TMSS web page then appears.

Click Service Summary.

3

Click Activate My Services to begin a 3step process to activate TMSS

TMSS is now active and can now monitor Prestige

LAN computers with TMSS installed.

Use Parental Control to forbid access to undesirable web site content based on pre-defined web site categories. See the TM User’s Guide for details on all features. You can also configure TMSS using the

Prestige web configurator.

Click TMSS under

Advanced Setup.

4 Fill in the registration form and submit it. After you submit the registration form, you will receive an email with instructions for validating your e-mail address. Follow the instructions. Download TMSS to each computer (behind the Prestige) that you want TMSS to monitor.

11

Prestige 661H/HW Series Quick Start Guide

7 Troubleshooting

PROBLEM CORRECTIVE ACTION

None of the LEDs turn on when you connect the Prestige’s power.

Make sure that you have the correct power adaptor connected to the Prestige, it is plugged into an appropriate power source and the Prestige is turned on.

Check all cable connections. If the LEDs still do not turn on, you may have a hardware problem. In this case, you should contact your local vendor.

Cannot access the Prestige from my computer.

Check the cable connection from your computer to the Prestige.

Make sure your computer’s IP address is in the same subnet as the Prestige’s

IP address (see Section 7.1 on page 12 ).

Ping the Prestige from a computer on the LAN. Make sure your computer’s

Ethernet adapter is installed and functioning properly. In the computer, click

Start, (All) Programs, Accessories and then Command Prompt. In the

Command Prompt window, type "ping" followed by the Prestige’s LAN IP address (192.168.1.1 is the default) and then press [ENTER]. The Prestige

should reply; otherwise see Section 7.1 on page 12 .

Cannot access the Internet.

If the Prestige’s IP address has changed, then enter the new one as the URL.

Use Internet Explorer 6.0 and later or Netscape Navigator 7.0 and later with

JavaScript enabled.

Make sure you enter the password correctly (the field is case sensitive).

If you’ve forgotten the Prestige’s password, use the RESET button. Press the button in for about 10 seconds (or until the PWR/SYS LED starts to blink), then release it. It returns the Prestige to the factory defaults (password is 1234, LAN

IP address 192.168.1.1 etc.; see your User’s Guide for details).

Verify the Internet connection settings in the wizard. Make sure you entered the correct user name and password if you are using PPPoE or PPPoA.

For wireless clients, check that both the Prestige 661HW and wireless client(s) are using the same SSID, channel and WEP or WPA-PSK keys (if configured).

7.1 Set Up Your Computer’s IP Address

This section shows you how to set your Windows NT/2000/XP computer to automatically get an IP address.

This ensures that your computer can connect with your Prestige. Refer to your User’s Guide for detailed IP address configuration for other Windows and Macintosh computer operating systems.

1 In Windows XP, click start, Control Panel. In Windows 2000/NT, click Start, Settings, Control Panel.

2 In Windows XP, click Network Connections. In Windows 2000/NT, click Network and Dial-up

Connections.

3 Right-click Local Area Connection and then click Properties.

12

Prestige 661H/HW Series Quick Start Guide

4 Select Internet Protocol (TCP/IP) (under the General tab in

Windows XP) and click Properties.

5 The Internet Protocol TCP/IP Properties screen opens (the

General tab in Windows XP).

6 Select the Obtain an IP address automatically and Obtain

DNS server address automatically options.

7 Click OK to close the Internet Protocol (TCP/IP) Properties window.

8 Click Close (OK in Windows 2000/NT) to close the Local Area

Connection Properties window.

9 Close the Network Connections screen.

7.2 Viewing Your Product’s Certifications

1 Go to www.zyxel.com

.

2 Select your product from the drop-down list box on the ZyXEL home page to go to that product's page.

3 Select the certification you wish to view from this page.

13