Delfield 18648-PTB Commercial Refrigerator

Delfield 18648-PTB Commercial Refrigerator
Delfield
™
®
18600 Series and CTP-NB
Service and Installation Manual
Please read this manual completely before attempting to install or operate this equipment! Notify carrier of damage! Inspect all
components immediately. See page 2.
18600PTL
Pizza Tables with LiquiTec® Rail
18600PTB
Pizza Tables with Raised Rail
18600BST
Work Table with Backsplash
N
CAUTIO
18600BUC
Work Tables
CTP-NB
Countertop Condiment Rail
ION
T
A
M
R
INFO
T
N
A
T
R
USE
IMPO
E
R
O
F
E
NS!
O
I
T
C
READ B
U
NSTR
I
E
S
E
H
VE T
A
S
E
Effective December 2007
S
A
PLE
18600 and CTP-NB Series Service and Installation Manual
CONTENTS
RECEIVING & INSPECTING EQUIPMENT............................................. 2
SPECIFICATIONS.................................................................................... 3
INSTALLATION . .................................................................................... 4
CARE AND CLEANING........................................................................4-6
OPERATION
18600PTB & PTL Series.................................................................... 6
18600BUC & BST Series.................................................................... 7
CTP-NB Series.................................................................................... 7
REFG. CHARGES & PRESSURE CONTROL SETTINGS........................ 8
WIRING DIAGRAM
18600PTB & PTL Series................................................................... 9
18600BUC & BST Series.................................................................. 10
CTP-NB Series.................................................................................. 10
REFRIGERATION SYSTEM
18600PTB & PTL Series.................................................................. 11
18600BUC & BST Series.................................................................. 11
CTP-NB Series.................................................................................. 12
PARTS REPLACEMENT LIST............................................................... 13
STANDARD LABOR GUIDELINES........................................................ 14
STANDARD WARRANTIES.............................................................15-16
NOTES.............................................................................................17-19
Serial Number Information
The serial number on 18600 Series units is located on the electrical
specifications tag affixed inside the compressor section next to the
pressure control.
The serial number on CTP-NB Series units is located on the front of
the unit.
Always have the serial number of your unit available when calling for
parts or service.
Warranty may be deemed invalid if other than
authorized OEM (original equipment manufacture)
replacement parts are used in Delfield equipment.
©2007 The Delfield Company. All rights reserved. Reproduction
without written permission is prohibited.
“Delfield” is a registered trademark of The Delfield Company.
Receiving and Inspecting the Equipment
Even though most equipment is shipped crated, care should
be taken during unloading so the equipment is not damaged
while being moved into the building.
1. Visually inspect the exterior of the package and skid or
container. Any damage should be noted and reported
to the delivering carrier immediately.
2. If damaged, open and inspect the contents with the
carrier.
3. In the event that the exterior is not damaged, yet upon
opening, there is concealed damage to the equipment
notify the carrier. Notification should be made verbally
as well as in written form.
4. Request an inspection by the shipping company of the
damaged equipment. This should be done within 10
days from receipt of the equipment.
5. Check the lower portion of the unit to be sure legs or
casters are not bent.
6. Also open the compressor compartment housing and
visually inspect the refrigeration package. Be sure lines
are secure and base is still intact.
7. Freight carriers can supply the necessary damage forms
upon request.
8. Retain all crating material until an inspection has been
made or waived.
Uncrating the Equipment
First cut and remove the banding from around the crate.
Remove the front of the crate material, use of some tools will
be required. If the unit is on legs remove the top of the crate
and lift the unit off the skid. If the unit is on casters it can be
"rolled" off the skid.
Delfield
™
2
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
®
18600 and CTP-NB Series Service and Installation Manual
Specifications
MODEL NUMBER
# OF DOORS
# OF
SHELVES
SHELF AREA
FT2
STORAGE
CAPACITY FT3
BTU LOAD
BASE/RAIL
BTU SYS. CAP.
BASE/RAIL
H.P.
AMPS
NEMA PLUG
SHIP WEIGHT
LBS/KG
18600PTB Pizza tables with raised rail
18648PTB
(1) 27”
1
3.36
8.39
470/441
2001/952
1/4
10.0
5-15P
520/236
18660PTB
19” & 27”
2
5.63
14.31
694/617
2409/1208
1/3
12.0
5-15P
575/260
18672PTB
(2) 27”
2
7.72
16.77
776/794
2967/1587
1/2
14.0
5-20P
635/288
18691PTB
(2)27” & (1) 19”
3
9.99
22.82
1062/1058
3537/1865
1/2
14.0
5-20P
770/350
18699PTB
(3) 27”
3
11.58
25.87
1144/1147
3537/1945
1/2
14.0
5-20P
805/365
186114PTB
(3) 32”
3
13.22
30.9
1297/1323
5169/2433
3/4
16.0
5-20P
927/420
18648BUC
(1) 27”
1
3.95
9.77
475/NA
1462/NA
1/5
8.0
5-15P
390/177
18660BUC
19” & 27”
2
6.51
14.31
686/NA
1462/NA
1/5
8.0
5-15P
435/197
18672BUC
(2) 27”
2
7.90
17.79
856/NA
2261/NA
1/4
10.0
5-15P
495/225
18691BUC
(2)27” & (1) 19”
3
10.29
23.05
1169/NA
2261/NA
1/4
10.0
5-15P
535/243
18600BUC Work tables
18699BUC
(3) 27”
3
11.85
25.82
1220/NA
2591/NA
1/3
12.0
5-15P
594/269
186114BUC
(4) 24”
4
14.42
27.58
1373/NA
2591/NA
1/3
12.0
5-15P
685/310
1
3.95
9.77
475/NA
1462/NA
1/5
8.0
5-15P
390/177
18600BST Work table with backsplash
18648BST
(1) 27”
18660BST
19” & 27”
2
6.51
14.31
686/NA
1462/NA
1/5
8.0
5-15P
435/197
18672BST
(2) 27”
2
7.90
17.79
856/NA
2261/NA
1/4
10.0
5-15P
495/225
18691BST
(2)27” & (1) 19”
3
10.29
23.05
1169/NA
2261/NA
1/4
10.0
5-15P
535/243
18699BST
(3) 27”
3
11.85
25.82
1220/NA
2591/NA
1/3
12.0
5-15P
594/269
186114BST
(4) 24”
4
14.42
27.58
1373/NA
2591/NA
1/3
12.0
5-15P
685/310
18600PTL Pizza table with LiquiTec rail
18648PTL
(1) 27”
1
3.36
8.36
470/441
2001/952
1/4
10.0
5-15P
520/236
18672PTL
(2) 27”
2
7.72
16.77
776/794
2967/1587
1/2
14.0
5-20P
635/288
3
11.58
25.87
1144/1147
3537/1945
1/2
14.0
5-20P
805/365
H.P.
AMPS
NEMA PLUG
SHIP WEIGHT
LBS/KG
18699PTL
(3) 27”
MODEL NUMBER
1/6 PAN SIZE
CAPACITY
#OF ADAPTER BARS
BTU LOAD
BTU SYSTEM CAPACITY
CTP-NB Counter top containment rail
CTP8146-NB
8
5
305
523
1/5
4.0
5-15P
121/54.9
CTP8160-NB
12
7
462
653
1/5
4.0
5-15P
158/71.7
CTP8175-NB
16
9
609
742
1/5
4.0
5-15P
197/89.4
Volts/Hertz/Phase for all CTP-NB & 18600 series is 115/60/1
Delfield
™
®
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
3
18600 and CTP-NB Series Service and Installation Manual
Installation
Location
These units are intended for indoor use only. Be sure the location
chosen has a floor strong enough to support the total weight of the
cabinet and contents. A fully loaded 72” long model may weigh as
much as 1200 pounds. Reinforce the floor as necessary to provide
for maximum loading.
Plumbing
Self-contained models are standard with a condensate evaporator.
If, for some reason, a unit does not have a condensate evaporator,
or the evaporator fails, the unit’s drain must have an outlet to an
appropriate drainage area or container.
For the most efficient refrigeration, be sure to provide good air
circulation inside and out.
CAUTION
Inside cabinet: Do not pack refrigerator so full that air cannot
circulate.
Outside cabinet: Be sure that the unit has access to ample air.
Avoid hot corners and locations near stoves and ovens.
It is recommended that the unit be installed no closer than 1” from
any wall.
Leveling
Moisture collecting from improper drainage can
create a slippery surface on the floor and a hazard to
employees. It is the owner’s responsibility to provide
a container or outlet for drainage.
Electrical connection
Refer to the amperage data on page 3, the serial tag, your local
code or the National Electrical Code to be sure the unit is connected
to the proper power source. A protected circuit of the correct
voltage and amperage must be run for con­nec­tion of the line cord,
or permanent connection to the unit.
The power switch must be turned to OFF and the
unit disconnected from the power source whenever
performing service or maintenance functions.
Never operate the unit without the louvered panel in
place!
A level cabinet looks better and will perform better because the
drain pan will drain properly, the doors will line up with the frames
properly, and the cabinet will not be subject to undue strain.
Some models have casters for your convenience, for ease of
cleaning underneath and for mobility. It is important that the unit
be installed in a stable condition with the front casters locked
before operating.
Care & Cleaning
Door Gasket Maintenance
Door gaskets require regular cleaning to prevent mold and mildew
build up and also to retain the elasticity of the gasket. Gasket
cleaning can be done with the use of warm soapy water. Avoid
full strength cleaning products on gaskets as this can cause them
to become brittle and crack. Never use sharp tools or knives to
scrape or clean the gasket. Gaskets can be easily replaced and do
not require the use of tools or an authorized service person. The
gaskets are “Dart” style and can be pulled out of the groove in the
door and new gaskets can be “pressed” back into place.
Drain Maintenance - Base
Each unit has a drain located inside the unit that removes the
condensation from the evaporator coil and routes it to an external
condensate evaporator pan. Each drain can become loose or
disconnected during normal use. If you notice water accumulation
on the inside of the unit be sure the drain tube is connected to
the evaporator drain pan. If water is collecting underneath the
unit make sure the end of the drain tube is in the condensate
evaporator in the machine compartment. The leveling of the unit is
important as the units are designed to drain properly when level.
Be sure all drain lines are free of obstructions.
Drawer Maintenance
Drawer Assembly Cleaning
The drawer assembly is designed to be cleaned easily. Both
drawer and tracks are removable without tools. The intermediate
drawer tracks are dishwasher safe or can be cleaned in a sink with
detergents and a soft bristle brush. Drawers and tracks should be
cleaned on a weekly basis.
4
Remove Drawers
To remove a drawer, simply pull the drawer out until it stops. At this
point lift up on the drawer front and pull the drawer completely out.
Using a soft bristle brush, clean the track on the bottom of the drawer
box. When finished, it should be wiped clean of all food and debris.
Tracks
To remove the intermediate tracks, the drawer box assembly must be
removed. The intermediate tracks are removed by pulling the track
out 1.50” to 2.00” (3.8cm to 5.0cm). Line up the rear white roller
with the half moon notch in the outer profile, and then rotate the track
away from the outer track profile freeing the intermediate profile. The
intermediate drawer tracks are dishwasher safe or can be cleaned in
a sink with detergents and a soft bristle brush. Drawers and tracks
should be cleaned on a weekly basis. Using a soft bristle brush, wash
the intermediate track making sure each roller is thoroughly cleaned.
The outer profile track should be cleaned with a soft bristle brush,
removing any food and debris gathered on the bottom ledge. Once it’s
cleaned thoroughly with a soft bristle brush, wipe remaining debris
clean with a soft towel.
Reassembly
Place intermediate tracks back into the outer track profile by lining
up the rear roller with the half moon notch and rotating towards the
outer profile. Once all tracks are replaced, insert the drawer box. Rest
the drawer box bottom track on the front intermediate track roller.
Then push the drawer back in place SLOWLY. When the drawer box
is about half way in you will hit a STOP. You must lift the front of the
drawer up approximately ½” (1.3cm) to continue inward. Clean tracks
as often as possible. The cleaner the tracks are the better they will
operate.
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
Delfield
™
®
18600 and CTP-NB Series Service and Installation Manual
Care & Cleaning
Caster Maintenance
Wipe casters with a damp cloth monthly to prevent corrosion.
The power switch must be turned to OFF and the
unit disconnected from the power source whenever
performing service, maintenance functions or cleaning
the refrigerated area.
Refrigerators and Freezers
The interior and exterior can be cleaned using soap and warm
water. If this isn’t sufficient, try ammonia and water or a
nonabrasive liquid cleaner. When cleaning the exterior, always rub
with the “grain” of the stainless steel to avoid marring the finish.
Do not use an abrasive cleaner because it will scratch the stainless
steel and can damage the breaker strips and gaskets.
months, the frequency of cleaning should be increased. Clean the
condenser with a vacuum cleaner or stiff brush. If extremely dirty, a
commercially available condenser cleaner may be required.
Failure to maintain a clean condenser coil can initially cause high
temperatures and excessive run times. Continuous operation with
a dirty or clogged condenser coil can result in compressor failure.
Neglecting the condenser coil cleaning procedures will void any
warranties associated with the compressor and cost to replace the
compressor.
Never use a high-pressure water wash for this
cleaning procedure as water can damage the
electrical components located near or at the
condenser coil.
Doors/Hinges
Stainless Steel Care and Cleaning
To prevent discoloration of rust on stainless steel several important
steps need to be taken. First, we need to understand the properties
of stainless steel. Stainless steel contains 70- 80% iron, which will
rust. It also contains 12-30% chromium, which forms an invisible
passive film over the steels surface, which acts as a shield against
corrosion. As long as the protective layer is intact, the metal is still
stainless. If the film is broken or contaminated, outside elements
can begin to breakdown the steel and begin to form discoloration
of rust. Proper cleaning of stainless steel requires soft cloths or
plastic scouring pads.
NEVER USE STEEL PADS, WIRE BRUSHES OR SCRAPERS!
Cleaning solutions need to be alkaline based or non-chloride
cleaners. Any cleaner containing chlorides will damage the
protective film of the stainless steel. Chlorides are also commonly
found in hard water, salts, and household and industrial cleaners. If
cleaners containing chlorides are used be sure to rinse repeatedly
and dry thoroughly. Routine cleaning of stainless steel can be done
with soap and water. Extreme stains or grease should be cleaned
with a non-abrasive cleaner and plastic scrub pad. Always rub with
the grain of the steel. There are stainless steel cleaners available
which can restore and preserve the finish of the steels protective
layer. Early signs of stainless steel breakdown are small pits and
cracks. If this has begun, clean thoroughly and start to apply
stainless steel cleaners in attempt to restore the passivity of the
steel.
Over time and with heavy use doors the hinges may become loose.
If this happens tighten the screws that mount the hinge brackets to
the frame of the unit. Loose or sagging doors can cause the hinges
to pull out of the frame, which may damage both the doors and the
hinges. In some cases this may require qualified service agents or
maintenance personnel to perform repairs.
Do not place hot pans on/against the blue ABS liner.
Do not throw items into the storage area. Failure to
follow these recommendations could result in damage
to the interior of the cabinet or to the blower coil.
Overloading the storage area, restricting the airflow,
and continuous opening and closing of the doors and
drawers will hamper the units ability to maintain
operational temperature.
Never use an acid based cleaning solution! Many food
products have an acidic content, which can deteriorate
the finish. Be sure to clean the stainless steel
surfaces of ALL food products. Common items include,
tomatoes, peppers and other vegetables.
Cleaning the Condenser Coil
In order to maintain proper refrigeration performance, the
condenser fins must be cleaned of dust, dirt and grease regularly.
It is recommended that this be done at least every three months.
If conditions are such that the condenser is totally blocked in three
Delfield
™
®
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
5
18600 and CTP-NB Series Service and Installation Manual
Care & Cleaning
Refrigerated rail units
Product in the rail should be removed to the refrigerated base at the
end of the day. This allows you to turn the rail off at night to save
energy and to defrost the rail. It also helps maintain product quality.
The standard wrapped refrigerated rail units are controlled by a lowpressure control that is set to maintain the proper rail temperature.
An on/off switch is also provided for the rail and is required to be shut
off at night. With a LiquiTec rail a thermostat is provided to maintain
rail temperature as well as the rail on/off switch. The LiquiTec rail
is required to be shut off at night as well to allow for defrosting. To
ensure product quality in the rail it is recommended that product be
rotated every four hours.
If adding any item to the unit, be sure to keep in mind
the location of the refrigeration lines on wrapped rail
units. A refrigeration leak in a rail is extremely difficult
and costly to repair. In some cases it cannot be repaired
at all.
Preventing blower coil corrosion
To help prevent corrosion of the blower coil, store all acidic items,
such as pickles and tomatoes, in sealable containers. Immediately
wipe up all spills.
Units with pans should be operated with pans in place.
Operating the unit without all pans in place will lower
efficiency and may damage the unit.
Continuous opening and closing of the doors will hamper the unit’s
ability to maintain optimum refrigeration temperature. Top section is
not intended for overnight storage. Product should be removed from
pans. Pans can remain in unit while empty.
Operation: 18600PTB & PTL SERIES
Product should be loaded into the unit with care.
Failure to heed these recommendations could result
in damage to the interior of the cabinet or the blower
coil.
This unit is equipped with two on/off switches located behind
the louvered machine compartment panel. The unit’s com­pres­sor
and all evaporator fans will begin op­er­at­ing when the main power
switch is turned to the ON position. Tem­per­a­ture ranges for the
base are 36°F to 40°F.
The switch labeled rail is for the raised rail. The rail switch is
accesible through a 1.5” diameter hole in the louvered panel.
Turning this switch to the ON position will activate the refrigeration
for the rail. Temperature ranges for the raised rail are 33°F to 41°F.
A minimum of one hour of off time per day with the pans removed
from the rail is required to properly defrost the rail.
The power must be turned to OFF and the unit
disconnected from the power source whenever
performing service or maintenance functions.
Never operate the unit without the louvered panel in
place!
All R404A models have a high pressure limiting device. Under
severe overloading conditions, or in the event of a condenser fan
failure or a plugged or blocked condenser, this device may shut
down the refrigeration system. This device will automatically reset,
but determining the cause of the high pressure condition should be
investigated by a qualified refrigeration technician.
Product located in the rail must be removed at the end
of day. This allows you to turn the rail off at night to
save energy and the rail will have time to defrost as
needed.
Delfield
™
6
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
®
18600 and CTP-NB Series Service and Installation Manual
Operation: 18600buc & BST SERIES
After turning the ON/OFF switch to ON, the units compressor
will begin operating. Delfield refrigerated bases are designed to
maintain an operational temperature of 36°F to 40°F.
Product should be loaded into the unit with care.
Failure to heed these recommendations could result
in damage to the interior of the cabinet or the blower
coil.
Overloading the storage area, restricting the air flow
and continuous opening and closing of the doors and
drawers will hamper the units ability to maintain
operational temperature.
Operation: ctp-nb SERIES
The unit is equipped with one on/off switch located on the right
end of the unit. The unit’s com­pres­sor will begin op­er­at­ing when
this switch is turned to the ON position. Tem­per­at­ure ranges for
the rail are 33°F to 41°F.
Product located in the rail must be removed at the
end of day. This allows you to turn the rail OFF at
night to save energy and the rail will have time to
defrost as needed.
Delfield
™
A minimum of one hour of off time per day with the pans removed
from the rail is required to properly defrost the rail.
The power switch must be turned to OFF and the
unit disconnected from the power source whenever
performing service or maintenance functions.
Never operate the unit without the louvered panel in
place!
®
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
7
18600 and CTP-NB Series Service and Installation Manual
Refrigerant charges and pressure control settings
Refrigerant Charges For 18600 Series Units:
18648-PTB & PTL . . . . . . . . . . . . . . . . . 16 oz.
18660-PTB . . . . . . . . . . . . . . . . . . . . . . . 24 oz.
18672-PTB & PTL . . . . . . . . . . . . . . . . . 32 oz.
18691-PTB . . . . . . . . . . . . . . . . . . . . . . . 32 oz.
18699-PTB & PTL . . . . . . . . . . . . . . . . . 48 oz.
186114-PTB . . . . . . . . . . . . . . . . . . . . . . 48 oz.
18648-BUC & BST . . . . . . . . . . . . . . . . . 16 oz.
18660-BUC & BST . . . . . . . . . . . . . . . . . 16 oz.
18672-BUC & BST . . . . . . . . . . . . . . . . . 16 oz.
18691-BUC & BST . . . . . . . . . . . . . . . . . 16 oz.
18699-BUC & BST . . . . . . . . . . . . . . . . . 24 oz.
186114-BUC & BST . . . . . . . . . . . . . . . . 24 oz.
Refrigerant Charges For CTP-NB Series Units:
CTP8146-NB . . . . . . . . . . . . . . . . . . . . . . 8 oz.
CTP8160-NB . . . . . . . . . . . . . . . . . . . . . . 8 oz.
CTP8175-NB . . . . . . . . . . . . . . . . . . . . . . 8 oz.
Pressure Control Settings
Pressure Control Settings
The factory recommended low-pressure control settings for 18600PTB’s are: 55# cut-in and 30# cut-out to maintain
proper temperature for product in the rail. The interior temperature is controlled by the thermostat mounted on the
evaporator coil housing.
The factory recommended low-pressure control settings for 18600BUC’s & BST’s are: 82# cut-in and 57# cut-out to
maintain proper temperature.
Pressure Control
The temperature is controlled by an adjustable pressure
control located in the machine compartment. An adjustable
control has the word COLDER near the knob, with an arrow
to indicate the adjustment direction. These controls are
field adjustable and do not require a service agent.
I n attempting to adjust the pressure control,
you can do damage to your unit by accidentally
adjusting the differential. Please make small
incremental adjustments if a temperature
adjustment is necessary, please contact the
service department at Delfield (800) 733-8829
or your local service agent. Delfield is not
responsible for charges incurred while having
the pressure control adjusted.
Pressure Control Settings-PTL
The 18600PTL uses a thermostat located in the mechanical section to control product temperature in the rail.
Delfield
™
8
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
®
18600 and CTP-NB Series Service and Installation Manual
Wiring diagram - 18600PTB series
L1
N
G
ON/OFF SWITCH
CONDENSING UNIT
PRESSURE CONTROL
POWER CORD
PROVIDED ON
SELF-CONTAINED
MODELS
BASE
EVAPORATOR FAN(S)
T'STAT
SOLENOID VALVE(S)
SWITCH
RAIL
SOLENOID VALVE
OPTIONAL RECEPTACLE FOR OPTIONAL
FAN PACKAGE
Wiring diagram - 18600PTl series
L1
N
G
ON/OFF SWITCH
CONDENSING UNIT
PRESSURE CONTROL
POWER CORD
PROVIDED ON
SELF-CONTAINED
MODELS
BASE
EVAPORATOR FAN(S)
T'STAT
SOLENOID VALVE(S)
3
RAIL
Delfield
™
®
1
SWITCH
5
SOLENOID VALVE
T‘STAT
OPTIONAL RECEPTACLE FOR OPTIONAL
FAN PACKAGE
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
9
18600 and CTP-NB Series Service and Installation Manual
Wiring diagram - 18600buc & bst series
L1
N
G
POWER SWITCH
Pressure control
CONDENSING UNIT
BASE COIL 1
BASE COIL 2
(where used)
EVAPORATOR FANS
PRESSURE SWITCH CONTROLS ONLY THE CONDENSING UNIT
Wiring diagram - ctp-nb series
N
L1
G
POWER SWITCH
CONDENSING UNIT
TEMPERATURE CONTROLS THE CONDENSING UNIT
Delfield
™
10
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
®
18600 and CTP-NB Series Service and Installation Manual
Refrigeration system- 18600PTB & PTL series
WRAPPED RAIL
EVAPORATOR
COIL
EVAPORATOR
COIL
SOLENOID
VALVE
AT
OST
RM
THE
EXPANSION VALVE
SOLENOID
VALVE
EXPANSION VALVE
SOLENOID
VALVE
LOW PRESSURE CONTROL
FILTER DRYER
EXPANSION
VALVE
HI-PRESSURE SAFETY SWITCH
CONDENSING UNIT
Refrigeration system- 18600buc & bst series
EVAPORATOR
COIL
EVAPORATOR
COIL
EXPANSION VALVE
EXPANSION VALVE
LOW PRESSURE CONTROL
FILTER DRYER
HI-PRESSURE SAFETY SWITCH
CONDENSING UNIT
Delfield
™
®
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
11
18600 and CTP-NB Series Service and Installation Manual
Parts replacement list
PART #
3516101
3234072
3234073
3234391
9321107
039-231-0000
(PMK00036)
2162691
3516172
3516173
3516095
3516273
3516225
3516102
3516103
2193927
2194536
3234161
3234546
3977984
3978014
3977983
1701183
1701185
1701186
9321374
9321041
3234266
3234282
3234392
2190154
2194939
DESCRIPTION
Filter dryer
Hinge bracket
Hinge Bracket
L-Shape hinge bracket
Bushing
ADDITIONAL PARTS FOR THE CTP SERIES ONLY
PART #
DESCRIPTION
3516047
Temp. control
2183304
Power cord
Cap. tube specs - 0.036 “ID x 72” long
Evaporator drain pan
Evaporator fan motor
Evaporator fan blade
Evaporator fan guard
Evaporator coil
Expansion valve (base) 1/4 ton, HI 404A
Expansion valve (rail) 1/4 ton, 404A
Solenoid valve 1/4 ODF
Solenoid coil 120v
Pressure control, low
Temp control (base)
Caster
Leg 6”
Wire shelf 19” door
Wire shelf 27” door
Wire shelf 32” door
Door gasket 19”
Door gasket 27”
Door gasket 32”
Salad pan cover pin hinge
Chrome acorn nut #10-24
Lid bracket right hand
Lid bracket left hand
Lid bracket center
On/Off switch and rail switch
Thermostat, Danfoss, ETC1H-1
Delfield
™
12
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
®
18600 and CTP-NB Series Service and Installation Manual
Standard Labor Guidelines To Repair or Replace Parts on Delfield Equipment
Advice and recommendations given by Delfield Service Technicians do not constitute or guarantee any special coverage.
•A maximum of 1-hour is allowed to diagnose a defective component.
•A maximum of 1-hour is allowed for retrieval of parts not in stock.
•A maximum travel distance of 100 miles round trip and 2-hours will be reimbursed.
•Overtime, installation/start-up, normal control adjustments, general maintenance, glass breakage, freight damage, and/or
correcting and end-user installation error will not be reimbursed under warranty unless pre-approved with a Service Work
Authorization from Delfield. You must submit the number with the service claim.
LABOR OF 1-HOUR IS ALLOWED TO REPLACE:
•Thermostat
•Evaporator/Condenser Fan Motor and Blade
•Door Hinges, Locks, and Gaskets
•Compressor Start Components and Overload Protector
•Thermometer
• Solenoid Coil
LABOR OF 2 HOURS TO REPLACE:
•Drawer Tracks/Cartridges
• Pressure Control
•Solenoid Valve
• Locate/Repair Leak
LABOR OF 3 HOURS TO REPLACE:
•Condenser or Evaporator Coil
•Expansion Valve
LABOR OF 4 HOURS TO REPLACE
•Compressor
This includes recovery of refrigerant and leak check.
$55.00 maximum reimbursement for refrigerant recovery (includes recovery machine, pump, torch, oil, flux, minor fittings,
solder, brazing rod, nitrogen or similar fees.)
REFRIGERANTS
•R404A A maximum of $12.00/lb. or 75¢/oz. will be reimbursed.
Delfield
™
®
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
13
18600 and CTP-NB Series Service and Installation Manual
Standard One Year Warranty (One year parts, 90 days labor.)
The Delfield Company (“Delfield”) warrants to the Original Purchaser
of the Delfield product (herein called the “Unit”) that such Unit, and all
parts thereof, will be free from defects in material and workmanship
under normal use and service for a period of one (1) year from
the date of shipment of the Unit to the Original Purchaser or, if the
Original Purchaser returns the warranty card completely filled out
including the date of installation within thirty (30) days of receipt
of the Unit, one (1) year from the date of installation. During this
one year warranty period, Delfield will repair or replace any defective
part or portion there of returned to Delfield by the Original Purchaser
which Delfield determines was defective due to faulty material or
workmanship. The Original purchaser will pay all labor, crating, freight
and related costs incurred in the removal of the Unit of defective
component and shipment to Delfield, except that during a period of
either ninety (90) days from the date of shipment of the Unit to the
Original Purchaser or, if the Original Purchaser returns the warranty
card completely filled out including the date of installation within thirty
(30) days of receipt of the Unit, ninety (90) days from the date of
installation Delfield will pay all related labor costs. Delfield will pay the
return costs if the Unit or part thereof was defective.
The term “Original Purchaser” as used herein means that person, firm,
association, or corporation for whom the Unit was originally installed.
This warranty does not apply to any Unit or part thereof that has
been subjected to misuse, neglect, alteration, or accident, such as
accidental damage to the exterior finish, operated contrary to the
recommendations specified by Delfield; or repaired or altered by anyone
other than Delfield in any way so as to, in Delfield’s sole judgement,
affect its quality or efficiency. This warranty does not apply to any Unit
that has been moved from the location where it was originally installed.
This warranty also does not cover the refrigerator drier or the light
bulbs used in the Unit. The warranty is subject to the user’s normal
maintenance and care responsibility as set forth in the Service and
Installation Manual, such as cleaning the condenser coil, and is in
lieu of all other obligations of Delfield. Delfield neither assumes, nor
authorizes any other person to assume for Delfield, any other liability
in connection with Delfield’s products.
Removal or defacement of the original Serial Number or Model Number
from any Unit shall be deemed to release Delfield from all obligations
hereunder or any other obligations, express or implied.
Parts furnished by suppliers to Delfield are guaranteed by Delfield only
to the extent of the original manufacturer’s express warranty to Delfield.
Failure of the Original Purchaser to receive such manufacturer’s express
warranty to Delfield. Failure of the Original Purchaser to receive such
manufacturers warranty shall in no way create any warranty, expressed
or implied, or any other obligation or liability on Delfield’s part in respect
thereof.
IF THE CUSTOMER IS USING A PART THAT RESULTS IN A VOIDED
WARRANTY AND A DELFIELD AUTHORIZED REPRESENTATIVE
TRAVELS TO THE INSTALLATION ADDRESS TO PERFORM WARRANTY
SERVICE, THE SERVICE REPRESENTATIVE WILL ADVISE CUSTOMER
THE WARRANTY IS VOID. SUCH SERVICE CALLS WILL BE BILLED
TO CUSTOMER AT THE AUTHORIZED SERVICE CENTER’S THEN
APPLICABLE TIME AND MATERIALS RATES. CONSIDER: CUSTOMER
MAY INITIATE A SERVICE AGREEMENT WITHOUT PARTS COVERAGE.
If shipment of a replacement part is requested prior to the arrival in
the Delfield factory of the part claimed to be defective, the Original
Purchaser must accept delivery of the replacement part of a C.O.D.
basis, with credit being issued after the part has been received and
inspected at Delfield’s plant and determined by Delfield to be within
this warranty.
Under no condition does this warranty give the Original Purchaser the
right to replace the defective Unit with a complete Unit of the same
manufacturer or of another make. Unless authorized by Delfield in
writing, this warranty does not permit the replacement of any part,
including the motor-compressor, to be made with the part of another
make or manufacturer.
No claims can be made under this warranty for spoilage of any
products for any reason, including system failure.
The installation contractor shall be responsible for building access,
entrance and field conditions to insure sufficient clearance to allow
any hood(s), vent(s), or Unit(s) if necessary, to be brought into the
building. Delfield will not be responsible for structural changes
or damages incurred during installation of the Unit or any exhaust
system.
Delfield shall not be liable in any manner for any default or delay in
performance hereunder caused by or resulting from any contingency
beyond Delfield’s control, including, but not limited to, war,
governmental restrictions or restraints, strike, lockouts, injunctions,
fire, flood, acts of nature, short or reduced supply of raw materials, or
discontinuance of the parts by the original part manufacturer.
Except as provided in any Additional Four Year Protection Plan,
if applicable, and the Service Labor Contract, if applicable, the
foregoing is exclusive and in lieu of all other warranties, whether
written or oral, express or implied. This warranty supersedes
and excludes any prior oral or written representations or
warranties. Delfield expressly disclaims any implied warranties
of merchantability, fitness for a particular purpose of compliance
with any law, treaty, rule or regulation relating to the discharge of
substances into the environment. The sole and exclusive remedies
of any person relating to the Unit, and the full liability of Delfield
for any breach of this warranty, will be as provided in this warranty.
Other than this Delfield Standard One Year Limited Warranty, any
applicable Delfield Additional Four Year Protection Plan or applicable
Delfield Service Labor Contract, the Original Purchaser agrees and
acknowledges that no other warranties are offered or provided in
connection with or for the unit or any other part thereof.
In no event will Delfield be liable for special, incidental or
consequential damages, or for damages in the nature of penalties.
IF DURING THE WARRANTY PERIOD, CUSTOMER USES A PART
FOR THIS DELFIELD EQUIPMENT OTHER THAN AN UNMODIFIED
NEW OR RECYCLED PART PURCHASED DIRECTLY FROM DELFIELD
OR ANY OF ITS AUTHORIZED SERVICE CENTERS AND/OR THE PART
BEING USED IS MODIFIED FROM ITS ORIGINAL CONFIGURATION,
THIS WARRANTY WILL BE VOID. FURTHER, DELFIELD AND ITS
AFFILIATES WILL NOT BE LIABLE FOR ANY CLAIMS DAMAGES
OR EXPENSES INCURRED BY THE CUSTOMER WHICH ARISE
DIRECTLY OR INDIRECTLY, IN WHOLE OR IN PART, DUE TO THE
INSTALLATION OF ANY MODIFIED PART AND/OR PART RECEIVED
FROM AN UNAUTHORIZED SERVICE CENTER. If the warranty
becomes void, Customer may purchase from Delfield, if available,
a Service Agreement or service at the then current time and
materials rate.
For more information on Delfield warranty’s log on and check out the
service section of our web site at www.delfield.com.
Delfield
™
14
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
®
18600 and CTP-NB Series Service and Installation Manual
Additional Four Year Protection Plan
Delfield Model#
Serial #
Installation
Date
In addition to the Standard One Year Warranty on the MotorCompressor contained in the above listed Delfield product (the
“Unit”), The Delfield Company (“Delfield”) also agrees to repair, or
exchange with similar or interchangeable parts in design and capacity
at Delfield’s option, the defective Motor-Compressor contained in the
Unit (the “Motor-Compressor), or any part thereof, for the Original
Purchaser only, at any time during the four (4) years following the
initial one (1) year period commencing on the date of installation for
the Original Purchaser. Failure of the Original Purchaser to register
the registration card containing the Original Purchasers name,
address, date of installation, model number and serial number of
the Unit containing the Motor-Compressor within 30 days from the
date of installation shall void this warranty. This additional warranty
is only available if the Motor-Compressor is inoperative due to defects
in material or factory workmanship, as determined by Delfield in
its sole judgement and discretion. The Original Purchaser shall be
responsible for returning the defective Motor-Compressor to Delfield
prepaid, F.O.B. at the address shown on the back cover of this manual.
The term “Original Purchaser” as used herein means that person, firm,
association, or corporation for whom the Unit was originally installed.
The term “Motor-Compressor” as used herein does not include unit
base, air or water cooled condenser, receiver, electrical accessories
such as relay, capacitors, refrigerant controls, or condenser fan/motor
assembly. This warranty does not cover labor charges incidental to
the replacement of parts. This warranty further does not include
any equipment to which said condensing unit is connected, such as
cooling coils, temperature controls or refrigerant metering devices.
This warranty shall be void if the Motor-Compressor, in Delfield’s
sole judgement, has been subjected to misuse, neglect, alteration
or accident, operated contrary to the recommendations specified
by the Unit manufacturer, repaired or altered by anyone other than
Delfield in any way so as, in Delfield’s sole judgment, to affect its
quality or efficiency or if the serial number has been altered, defaced
or removed. This Warranty does not apply to a Motor-Compressor in
any Unit that has been moved from the location where it was originally
installed. The addition of methyl chloride to the condensing unit or
refrigeration system shall void this warranty.
Delfield
™
(for Motor-Compressor only)
General Conditions
Delfield shall not be liable in any manner for any default or delay
in performance hereunder caused by or resulting from any
contingency beyond Delfield’s control, including, but not limited
to, war, governmental restrictions or restraints, strike, lockouts,
injunctions, fire, flood, acts of nature, short or reduced supply
of raw materials, or discontinuance of any part or the MotorCompressor by the unit manufacturer.
Replacement of a defective Motor-Compressor is limited to one (1)
Motor-Compressor by us during the four (4) year period. Delfield
shall replace the Motor-Compressor at no charge.
This warranty does not give the Original Purchaser of the MotorCompressor the right to purchase a complete replacement MotorCompressor of the same make or of another make. It further does
not permit the replacement to be made with a Motor-Compressor
of another kind unless authorized by Delfield. In the event Delfield
authorizes the Original Purchaser to purchase a replacement
Motor-Compressor locally, only the wholesale cost of the MotorCompressor is refundable.
Expressly excluded from this warranty are damages resulting from
spoilage of goods.
Except as provided in any applicable Standard One Year Limited
Warranty or applicable Service Labor Contract, the foregoing
is exclusive and in lieu of all other warranties, whether written
or oral, express or implied. This Warranty supersedes and
excludes any prior oral or written representations or warranties.
Delfield expressly disclaims any implied warranties of
merchantability, fitness for a particular purpose or compliance
with any law, treaty, rule or regulation relating to the MotorCompressor, and the full liability of Delfield for any breach of this
warranty, will be as provided in this warranty.
Other than any applicable Delfield Standard One year Limited
Warranty, this Delfield Additional Four Year Protection Plan and any
applicable Delfield Service Labor Contract, the Original Purchaser
agrees and acknowledges that no other warranties are offered or
provided in connection with or for the Motor-Compressor or any
part thereof.
In no event will Delfield be liable for special, incidental or
consequential damages, or for damages in the nature of penalties.
®
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
15
Delfield
™
®
Covington, TN
Mt. Pleasant, MI
Thank you for choosing Delfield!
Help is a phone call away. Help our team of professional, courteous
customer service reps by having your model number and serial number
available at the time of your call (800) 733-8829.
Model:_____________________ S/N: ____________________
Installation Date:_____________
For a list of Delfield’s authorized parts depots,
visit our website at www.delfield.com.
980 S. Isabella Rd., Mt. Pleasant, MI 48858, U.S.A. • +1(989) 773-7981 or (800) 733-8829 • Fax (866) 779-2040 • www.delfield.com
Delfield reserves the right to make changes in design or specifications without prior notice. ©2007 The Delfield Company. All rights reserved. Printed in the U.S.A.
DM18PTB 12/07
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement