Chaintech 9BIA (CT-9BIA) Motherboard - C:\Documents and Settings\Voffka\Desktop\9bia0

Add to my manuals
33 Pages

advertisement

Chaintech 9BIA (CT-9BIA) Motherboard - C:\Documents and Settings\Voffka\Desktop\9bia0 | Manualzz
Declaration of Conformity
According to 47 CFR, Parts 2 and 15 of the FCC Rules
The following designated product:
EQUIPMENT: MAINBOARD
MODEL NO.: 9BIA
is a Class B digital device that complies with 47 CFR Parts 2 and 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference
that may cause undesired operation.
This declaration is given to the manufacturer:
CHAINTECH - EXCEL COMPUTER U.S., INC.
4427 Enterprise ST. Fremont, CA 94538, U.S.A.
hattp://www.chaintech-excel.com
Chaintech President: Simon Ho
Signature:
Federal Communications Commission Statement
This device complies with FCC Rules Part 15. Operation is subject to the following two
conditions:
M
This device may not cause harmful interference
M
This device must accept any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy. If this equipment is not installed
and used in accordance with the manufacturer's instructions, it may cause harmful
interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:
M
Reorient or relocate the receiving antenna.
M
Increase the separation between the equipment and receiver.
M
Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
M
Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is required
to assure compliance with FCC regulations. Changes or modifications to this unit not
expressly approved by the party responsible for compliance could void the user's authority
to operate this equipment.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for audio noise emissions from
digital apparatuses set out in the Radio Interference Regulations of the Canadian
Department of Communications.
Manufacturer's Disclaimer Statement
The information in this document is subject to change without notice and does not represent a
commitment on the part of the vendor. No warranty or representation, either expressed or implied,
is made with respect to the quality, accuracy or fitness for any particular purpose of this document.
The manufacturer reserves the right to make changes to the content of this document and/or the
products associated with it at any time without obligation to notify any person or organization of
such changes. In no event will the manufacturer be liable for direct, indirect, special, incidental
or consequential damages arising out of the use or inability to use this product or documentation,
even if advised of the possibility of such damages. This document contains materials protected
by copyright. All rights are reserved. No part of this manual may be reproduced or transmitted
in any form, by any means or for any purpose without expressed written consent of it's authors.
Product names appearing in this document are mentioned for identification purposes only. All
trademarks, product names or brand names appearing in this document are registered property
of their respective owners.
Printed in Taiwan
June 2001
POST-CONSUMER
RECYCLED PAPER
Tab
le of Contents
able
Chapter
1-1
1-2
1-3
1-4
1 Introduction ........................................................................ 1
Product Specifications .......................................................... 1
Package Contents ................................................................. 3
Mainboard Layout .................................................................. 4
Connector and Jumper Reference Chart .............................. 5
Chapter
2-1
2-2
2-3
2-4
2 Hardware Setup ................................................................... 6
Introduction to Jumpers ........................................................ 6
Installing a CPU in a Socket 478 .......................................... 6
Setting Your CPU's Parameters...........................................7
Main Memory Configuration ................................................ 11
Chapter 3 Award BIOS Setup Program ........................................... 12
3-1 Standard CMOS Features ................................................... 13
3-2 Advanced BIOS Features ................................................... 15
3-3 Advanced Chipset Features ................................................ 18
3-4 Integrated Peripherals ......................................................... 19
3-5 Power Management Setup .................................................. 21
3-6 PnP/PCI Configuration ........................................................ 24
3-7 PC Health Status ................................................................. 25
3-8 Frequency/Voltage Control .................................................. 25
3-9 Load Fail-Safe Defaults ....................................................... 26
3-10 Load Optimized Defaults ..................................................... 26
3-11 Supervisor Password & User Password Setting ................ 27
3-12 Save and Exit Setup ........................................................... 27
3-13 Exit Without Saving ............................................................. 27
Feature Explanations
Software Power-off Control ............................................................. 7
Over-ride Power Button ................................................................... 8
Blinking LED in Suspend Mode ...................................................... 7
Power On By Modem .......................................................7/23
Resume By Alarm .......................................................23
Poly-fuse Over Current Protection ................................................. 7
Wake Up On LAN .......................................................................... 10
Appendices
Appendix I Embedded Flash Utility ............................................ 28
Appendix II HDD Instant Recovery Utility ................................... 29
Introduction
Chapter 1
Introduction
1-1 Product Specifications
r Processor
- Supports Intel Socket 478 Pentium 4 processors
- System bus 400MHz
r Chipset
- Intel 845 + ICH2 chipset
r DRAM Memory
- Two 168-pin DIMM sockets support up to 2 GB of SDRAM
- Supports PC-133 SDRAM
r Expansion Slots
- One Universal-AGP slot for both 2X/4XAGP at 1.5v (v2.0 compliant)
- Three 32-bit PCI slots (Rev 2.2 compliant)
- One CNR slot for modem, audio and LAN support
r Boot-Block Flash ROM
- Award System BIOS, supports PnP, APM, DMI, ACPI & Multi-device booting
features i.e. floppy, LS120, CD/DVD-ROM, HDD(IDE, SCSI), ZIP-ATAPI etc.
r Embedded Ultra DMA-100 PCI IDE controller
- Supports two IDE ports up to 4 ATAPI devices
- Supports up to PIO Mode 4 up to 16.6MBps, Multi Mode 4 up to 66MBps
and Multi Word Mode 5 up to 100MBps with bus mastering
- Bus Mastering software drivers for common multi-task operating systems
r Onboard Ultra I/O
- ITE 8712 LPC with system monitoring hardware
- Three UARTs support two serial ports and IR function for HPSIR and ASKIR
- One parallel supports SPP/ECP/EPP
- One floppy disk drive connector supports up to 2.88MB, Japanese 3-Mode,
and 1Mbps transfer rates
r Embedded USB Controller
- Four USB ports (UHCI v1.0 compliant)
- Optional USB riser with additional 2 USB ports
1
Chapter 1
r Double Stack Back-Panel I/O Connectors
- PS/2 Mini-DIN keyboard and mouse port
- Two USB ports
- Two 9-pin D-Sub male Serial port
- One 25-pin D-Sub female Printer port
- Audio Line-in/out and Mic-in jacks
- One 15-pin D-Sub female Game/MIDI port
r Embedded Audio Subsystem AC-link
- Full-duplex operation for simultaneous recording and plackback
- Built-in FM-emulation music synthesizer
- External high quality AC97 CODEC provides 90dB+SNR CD quality audio
- Use wavetable data on the system memory
- Hardware SoundBlaster Pro for Windows DOS box and real-mode DOS legacy
compatibility
r Embedded System Monitor Hardware
- 8 external voltage inputs
- 2 temperature sensor with thermistor for CPU and System
- 2 Fan speed monitoring with ON/OFF control in suspend
r Board Dimensions
- Micro ATX form factor, 244mm x 220mm, 4 Layers
r
2
Advanced Management Features
- Embedded System Monitoring Hardware
- Poly-fuse protection for USB and keyboard circuitry
- Embedded BIOS flash utility
- Complete Data Security:
* Flash BIOS write protection against unauthorized access
* Trend ChipAway Virus, to ensure virus-free booting procedure
- Advanced Management Features
*Power-on events:WOL(Wake-on-LAN) network card, Modem ring, RTC Alarm
* Software power-off control for Win9x
* Over-ride power button
* Power-failure recovery
* Blinking Power-LED in suspend
* Hardware Reset Protect
Introduction
1-2 Package Contents
This product comes with the following components:
r One mainboard
r One 40-pin (80-wire) UDMA-100 IDE connector ribbon cable (Figure 1-1)
* Color coded connection for UDMA 100 cable
Blue to mainboard, Gray to Master and Black to slave
r One 34-pin floppy disk drive ribbon cable (Figure 1-2)
r Optional USB adaptor (Figure 1-3)
r One User's Manual
r One CD-ROM that includes
- Acrobat Reader
- Award Flash Utility
- Award DMI Utility for DOS
- Intel audio driver and utility
- Intel Service Pack for Win9x/WinNT including Bus Master IDE drivers,
AGP VxD and etc.
- Optional Value Pack 2001 software group including Norton AntiVirus, AutoSave,
ADOBE ActiveShare, Acrobat Reader, Imagemore, X-stop, Appio and Ewalla.
@
See the Readme.txt file in the CD-ROM's root directory for installation
instructions of all driver and software utilities.
Figure 1-1
UDMA 66/100 IDE cable
Figure 1-2
Standard Floppy cable
USB3
USB4
JP1
Figure 1-1
Optional USB Adaptor
3
Chapter 1
1-3 Mainboard Layout
CN2,CN3,CN4,CN4A,
CN5,CN6,CN10,IR2
PW2
(12V)
JP5,JP6
JP1,CN1,CN7
CN17,FAN2
PS/2 Mouse
PS/2 Keyboard
4
PW1,FAN1
PW3(3.3V,5V)
Printer Port
USB 0/1 COM1
COM2
Game Port
Line-out Line-in MIC
Introduction
1-4 Connector and Jumper Reference Chart
Jumper &
Connector No.
Function
Page
JP1
Clear CMOS Data Jumper
9
JP5
Power On By Keyboard
9
JP6
Power On By USB
9
Over ride Power Button Connector
Power Indicator LED Connector
CN1
Green LED Connector
System Reset Switch Connector
8
Speaker Connector
IDE Activity LED Connector
CN2
CD-ROM Audio in Connector
9
CN3
Auxiliary Audio-in Connector
9
CN4
Optional Audio Mono-in/out Connector
9
Front Panel Audio Connector
10
WOL (Wake-on-LAN) Connector
10
USB 0/1Ports and USB 2/3 Connector
10
CN7
Smart Card Reader Connector
10
CN10
Alert On LAN Connector
10
CN17
Blue LED Connector
11
IR/CIR Connector
11
CPU/System Cooling Fan Connector
11
CN4A
CN5
USB1/CN6
IR2
FAN1/FAN2
PW1/PW2/PW3 ATX/ATX12V Power Supply Connector
PT1
PS/2 Mouse and Keyboard Ports
7
11
5
Chapter 2
Chapter 2
Hardware Setup
If your mainboard has already been installed in your computer you may still need
to refer to this chapter if you plan to upgrade your system's hardware.
Be sure to disconnect the power cable from the power source before performing
any work on your mainboard, i. e. installing a CPU, memory module, changing
a jumper setting, etc. Not doing so may result in electrical shock!
2-1 Installing a CPU in a Socket 478
The Intel Socket 478, designed for the Pentium 4 processor, has been incorporated
as a standard mainboard specification To insert your CPU into Socket 478 please
do the following:
1. Locate a small dot marked on the top surface of the CPU close to one if it's corners.
The same corner will also be cut off, leaving a noticeable notch in the CPU's corner.
These markings indicate Pin 1 of the CPU.
2. Pull up the lever of Socket 478 so that it is perpendicular with the surface of the
mainboard. Gently insert the CPU with Pin 1 at the same corner of Socket 478
that contains the end of the lever. Allow the weight of the CPU to push itself
into place. Do not apply extra pressure as doing so may result in damaging your
CPU. Snap the lever back into place.
Installing a standard Intel specified heat sink with cooling fan is necessary
for proper heat dissipation from your CPU. Failing to install these items
may result in overheating and possible burn-out of your CPU.
2-2 Setting Your CPU's Parameters(SeePU Technology)
SeePU is a new user friendly technology that enables the user to setup a mainboard's
CPU parameters through an easy to use BIOS setup procedure. It is no longer
necessary to make many jumper settings as on conventional mainboards.
After installing all your hardware into your PC system, you can manually configure
your CPU clock ratio according to your processor's specifications. By turning on
your system'spower. Enter the CMOS Setup Utility by pressing the Delete key
when your BIOS identification screen appears, then go to the Frequency/Voltage
Control option and select your CPU clock ratio (See Chapter 3).
You do not need to make voltage settings because SeePU automatically sets
your CPU voltage.
6
Hardware Setup
2-3 Connector and Jumper Settings
Connectors are used to link the system board with other parts of the system, including
the power supply, the keyboard, and the various controllers of the system case.
The power supply connector is the last connection to be made while installing a
mainboard. Before connecting the power supply, please make sure it is not
connected to the power source.
ATX/ATX12V Power Supply Connector (PW1/PW2/PW3)
PW1
Pin
Signal
Wire
1
COM
BLK
2
COM
BLK
BLK
3
COM
BLK
3
+12VDC YEL
4
+3.3VD
ORG
4
+12VDC YEL
5
+3.3VD
ORG
6
+5VDC
RED
Pin
Signal
Wire
1
COM
BLK
2
COM
PW2
PW3
The ATX power supply provides a single 20-pin
connector interface which incorporates standard +/
-5V, +/-12V, optional 3.3V and Soft-power signals.
The Soft-power signal, a 5V trickle supply is
continuously supplied when AC power is available.
When the system is in the Soft-Off mode, this trickle
supply maintains the system in it's minimum power
state.
The ATX12V power supply has a new +12 V (4pin) and +5 V/3.3 V(6-pin) auxiliary power
connector. To enable the delivery of more +12 VDC
and +5/3.3V VDC current to the motherboard.
Software Power-Off Control
This mainboard can be powered down using theWindows 9x Software Power-Off
function. To power down your computer, click the START button on the Windows 9x
task bar. Select "Shut Down The Computer" and the system turns off. The message "It
is now safe to turn off your computer" will not be shown when using this function.
Power-On By Modem
While in Soft-off state, if an external modem ring-up signal occurs, the system wakes up
and can be remotely accessed. You may enable this function in BIOS's Power
Management Setup menu. (See Chapter 3)
Blinking LED in Suspend Mode
While in Suspend mode, the LED light on the front panel of your computer will flash.
Suspend mode is entered by pressing the Override Power Button, pushing the Green
button on your ATX case, or enabling the Power Management and Suspend Mode
options in BIOS's Power Management menu. (See Chapter 3)
Poly-fuse Over Current Protection
The poly-fuse protects the system from dangerous voltages the system might be
exposed to via the keyboard or USB connectors. In case of such exposure, the polyfuse will immediately be disconnected from the circuit, just like a normal fuse. After
being disconnected for a certain period of time, the poly-fuse will return to its normal
state, after which the keyboard or USB can function properly again.
7
Chapter 2
Front Panel Connector Set (CN1) A through F
A. Over-ride Power Button Connector
The power button on the ATX chassis can be used as a
normal power switch as well as a device to activate
Advanced Power Management Suspend mode. This mode
is used for saving electricity when the computer is not in use
for long periods of time. The Soft-OFF by PWR-BTTN
function in BIOS's Power Management Setup menu must be
set to "Delay 4 Sec." to activate this function.
When the Soft-OFF by PWR-BTTN function is enabled,
pushing the power button rapidly will switch the system to
Suspend mode. Any occurence of external activities such
Over-ride Power Button
as pressing a key on the keyboard or moving the mouse will
bring the system back to Full-On. Pushing the button while
in Full-On mode for more than 4 seconds will switch the
system completely off. See Over-ride Power Button
Operation diagram.
B. Power Indicator LED Connector
The power indicator LED shows the system's power status. It is important to
pay attention to the correct cables and pin orientation (i.e., not to reverse the order
of these two connectors.)
C. Green Switch Connector
Some ATX cases provide a Green switch which is used to put the system in
Suspend mode. In Suspend mode, the power supply to the system is reduced
to a trickle, the CPU clock is stopped, and the CPU core is in it's minimum power
state. The system is woken up whenever the keyboard or mouse is touched. The
system resumes in different ways as defined by Power Management Setup screen
in BIOS.
D. System Reset Switch Connector
This connector should be connected to the reset switch on the front panel of
the system case. The reset switch allows you to restart the system without turning
the power off.
E. Speaker Connector
This 4-pin connector connects to the case-mounted speaker
F. IDE Activity LED Connector
The IDE activity LED lights up whenever the system reads/writes to the IDE
devices.
8
Hardware Setup
Clear CMOS Data (JP1)
Pin
Definition
1~2
Normal (default)
2~3
Clear CMOS Data
To clear the contents of the CMOS, please follow the steps
below.
1. Disconnect the system power supply from the power source.
2. Set the jumper cap at location 2~3 for 5 seconds, then set it back
to the default position.
3. Connect the system's power and then start the system.
4. Enter BIOS's CMOS Setup Utility and choose Load Setup
Defaults. Type Y and press enter.
5. Set the system configuration in the Standard CMOS Setup
menu.
Power On By Keyboard (JP5)
Pin
Definition
1~2
Disable (default)
2~3
Enable
This board is able to be turned on by the PS/2 keyboard (hot
key). To use this function, select a hot key of your choice at
the PS2KB Wakeup option under Wake Up Events in the BIOS's
Power On Management screen. You must also set this jumper's
cap to pins 2-3 to use this function.
Power On By USB (JP6)
Pin
Definition
1~2
Disable (default)
2~3
Enable
This board is able to be turned on by a USB keyboard hot key
or a USB mouse click. To use this function, select a hot key
of your choice at the USB Kb Power Wake-Up From S3/S4/S5
option under Wake Up Events in the BIOS's Power On Management
screen. You must also set this jumper's cap to pins 2-3 to use
this function.
CD-ROM Audio-in Connector (CN2)
L
1
GND
R
Use the audio cable enclosed with your CD-ROM disk drive to
connect the CD-ROM to your mainboard. This will enable your
CD-ROM's audio function.
Auxiliary Audio-in Connector (CN3)
This connector is for use with a secondary CD-ROM, DVD-ROM
or CDR/CDRW disk drive.
Optional Audio Mono-in/out Connector (CN4)
This connector is used for Add on Card e.g. modem with Mono
In/Out connector
9
Chapter 2
Front Panel Audio Connector (CN4A)
Rear
Panel
Front
Panel
This connector give you the option to choose between standard
audio jack(rear panel) or use a an optional front panel audio
jack cable ext. to be plug into a special custom designed system
case. To use the standard audio jack short jumper caps to pin12 and pin 3-4 (Default). To use the front panel audio jack cable
ext., simply removed both jumper caps and plug into the audio
jack cable.
WOL (Wake-on-LAN) Connector (CN5)
Enable the Wake Up On LAN selection in BIOS's Power
Management Menu to use this function. The capability to remotely
manage PCs on a network is a significant factor in reducing
administrative and ownership costs. Magic Packet technology
is designed to give WOL capability to the LAN controller. This
header is used to connect an add-in NIC (Network Interface Card)
which gives WOL capability to the mainboard.
USB 0/1Ports and USB 2/3 Connector (USB1/CN6)
If you want to use a USB keyboard, you must enable the USB
keyboard support function in BIOS's Integrated Peripherals menu
(See Section 3-4). This board contains a USB Host controller and
includes a root hub with two USB ports (meets USB Rev 1.0
spec.) and a connector for optional USB Adaptor (USB2/3). Four
USB peripherals or hub devices are able to be connected.
Smart Card Reader Connector (CN7)
This connector must be connected to a Smart card reader
(Optional).
Smart Card Reader (Optional)
Alert On LAN Connector (CN10)
.Alert On LAN enabled LAN controller to report messages to
a network management console without the aid of the system
processor. In order to use this function, the connector must be
connected to a LAN card that support AOL feature.
10
Hardware Setup
Blue LED Connector(CN17)
This feature work entirely the same as the power indicator LED,
both shows the system's power status. The only difference is that
this one is blue while the other is red LED.
IR/CIR Connector (IR2)
Select a UART Mode in BIOS's Integrated Peripherals menu the
UART port to support IR/CIR functions. (See section 3-4)
CPU/System Cooling Fan Connectors (FAN1/FAN2)
The board's management extension hardware is able to detect
the CPU and system fan speed in rpm (revolutions per minute).
These connectors supports 3-pin cooling fans with minimum
of 4500 RPM. The wiring and plug may vary depending on the
manufacturer. On standard fans, the red is positive (+12V), the
black is ground, and the yellow wire is the rotation signal.
PS/2 Mouse and Keyboard Ports (PT1)
Pin
1
2
3
4
5
6
Definition
Data
No Connection
Ground
+ 5V (fused)
Clock
No Connection
If a PS/2 mouse is used, BIOS will automatically detect and assign
IRQ12 to the PS/2 mouse.
2-4 Main Memory Configuration
The DRAM memory system consists two banks and the memory size ranges from
32MBytes~1GBytes. If you only use one bank it does not matter which one you use
and if you use two or more banks, it does not matter which bank you install first.
DRAM Specifications
DIMM type: 3.3V, 64/72-bit Synchronous DRAM
Module size: Single/double-sided 32/64/128/256/512MBytes/1GBytes
DRAM speed: 7.5/10ns for Synchronous DRAM
Parity:
Either parity or non-parity
This mainboard supports 3.3v, unbuffered, 4-clock, SDRAM DIMM only.
Buffered, 5V, or 2-clock SDRAM DIMMs should not be used.
Due to loading anomalies, using DIMM with an 'n x 4' DRAM base on this
mainboard is not recommended. For example, a DIMM that uses sixteen
16Mb x 4 devices should not be used.
11
User's Manual
Chapter 3
3
Award BIOS Setup Program
Award's BIOS ROM has a built-in setup program that allows users to modify the basic
system configuration. This information is stored in CMOS RAM so that it can retain
the setup information, even when the power is turned off.
When you turn on or reboot the system, press the Delete key to enter the Award
BIOS setup program. The primary screen as shown in Figure 3-1 is a list of the menus
and functions available in the setup program. Select the desired item and press enter
to make changes. Operating commands are located at the bottom of this and all other
BIOS screens. When a field is highlighted, on-line help information is displayed on
the left bottom edge of the screen.
CMOS Setup Utility- Copyright (C) 1984-2001 Award Software
Standard CMOS Features
Frequency/Voltage Setup
Advanced BIOS Features
Load Fail-Safe Defaults
Advanced Chipset Features
Load Optimized Defaults
Integreted Peripherals
Set Supervisor Password
Power Management Setup
Set User Password
PnP/PCI Configurations
Save & Exit Setup
PC Health Status
Exit Without Saving
Esc : Quit
F10 : Save & Exit Setup
: Select Item
Time, Date, Hard Disk Type...
Figure 3-1 Setup Program Initial Screen
12
Award BIOS Setup Program
3-1 Standard CMOS Setup
The Standard CMOS Setup allows users to configure system components such as
hard disk drive, floppy disk drive and video display as well as date, time and bootup error signaling. This configuration menu should be changed when installing a
mainboard for the first time, changing hardware in your system such as the HDD,
FDD, video display, or when the CMOS data has been lost or contaminated. Choose
the Standard CMOS Setup option from the CMOS Setup Utility menu (Figure 3-1)
to display the following screen. When a field is highlighted, on-line help information
is displayed on the left bottom edge of the screen.
CMOS Setup Utility- Copyright (C) 1984-2001 Award Software
Standard CMOS Features
Date (mm : dd : yy)
Time (hh : mm : ss)
June. 28, 2001
17 : 14 : 44
IDE Primary Master
IDE Primary Slave
IDE Secondary Master
IDE Secondary Slave
None
None
None
None
Drive A
Drive B
1.44M, 3.5 in.
None
Video
Halt On
EGA/VGA
All Errors
Base Memory
Extended Memory
Total Memory
640K
30720K
31744K
:Move Enter:Select
F5:Previous Values
Item Help
Menu Level
+/-/PU/PD:Value
F10:Save
ESC:Exit
F1:General Help
F6:Fail-Safe Defaults
F7:Optimized Defaults
Figure 3-2 Standard CMOS Features Screen
Date/Time
Set the date and time. Do not skip this function as all of your timed events such
as power management, saving files, etc. are based on this timer.
Hard Disk Setup (Primary/Secondary; Master/Slave)
This category identifies up to four IDE hard disk drives that have been installed in
the computer. This section does not show information on other IDE devices such
as CD-ROM drives or other hard drive types such as SCSI drives.
13
User's Manual
Floppy Disk Drives
Choose the memory capacity and disk size that corresponds with that of your floppy
disk drive(s).
Video
Select the type of video adapter present in your system. You can ignore this setting
if you are using a VGA monitor since VGA BIOS automatically configures this setting.
Halt
When the system is powered on, BIOS performs a series of diagnotic tests called
POST (Power On Self Test). This function stops the computer if BIOS detects a
hardware error. You can tell BIOS to halt on all errors, no errors, or not to halt on
specific errors.
14
Award BIOS Setup Program
3-2 Advanced BIOS Features
By choosing the Advanced BIOS Features option from the Standard CMOS Features
menu (Figure 3-1), the screen below is displayed. This sample screen contains the
manufacturer's default values for the mainboard.
CMOS Setup Utility- Copyright (C) 1984-2001 Award Software
Advanced BIOS Features
Anti-Virus Protection
CPU L1 & L2 Cache
Quick Power On Self Test
First Boot Device
Second Boot Device
Third Boot Device
Boot Other Device
Swap Floppy Drive
Boot Up Floppy Seek
Boot Up NumLock Status
Gate A20 Option
Typematic Rate Setting
Typematic Rate (Chars/Sec)
Typematic Delay (Msec)
Security Option
MPS Version Control For OS
OS (Select For DRAM > 64MB)
Small Logo(EPA) Show
Show POST CODE
:Move Enter:Select
F5:Previous Values
Disabled
Enabled
Enabled
Floppy
HDD-0
LS120
Enabled
Disabled
Enabled
On
Fast
Disabled
6
250
Setup
1.4
Non-OS2
Enabled
Enabled
Item Help
Menu Level
+/-/PU/PD:Value
F10:Save
ESC:Exit
F1:General Help
F6:Fail-Safe Defaults
F7:Optimized Defaults
Figure 3-3 Advanced BIOS Features Screen
A. Virus Warning
Trend ChipAway Virus
Trend ChipAway Virus is a code incorporated in the mainboard's BIOS firmware.
During the boot-up sequence, BIOS loads before loading of the partition table
or boot sector. ChipAway Virus loads with BIOS and is able to detect boot-up
viruses before they have a chance to infect the hard drive. ChipAway Virus
employs rule-based logic that doesn't look for specific viruses but rather detects
patterns found in every virus, eliminating the need to perform periodical version
updates after new viruses have been found.
15
User's Manual
B. CPU L1 and L2 Cache
Cache memory is much faster than conventional DRAM system memory. These
fields allow you to enable or disable the CPUs Level 1 built-in cache and Level
2 external cache. Both settings are left enabled to significantly increase the
performance of your computer.
C. Boot Up Features
After turning on the system, BIOS will perform a series of device initializations
and diagnostic tests discussed below.
Quick Power On Self Test (POST)
Enable this function to reduce the amount of time required to run the POST (Power
On Self Test). BIOS saves time by skipping some items during POST. It is
recommended that you disable this setting. Discovering a problem during bootup
is better than loosing data during your work.
First/Second/Third/Boot Other Device
This option sets the sequence of drives BIOS attempts to boot from after POST
completes. BIOS will search these drives for an operating system.
Swap Floppy Drive
Enabling this function will swap the floppy drive assignment so that drive A will
function as drive B, and drive B will function as drive A. Note that the boot
sequence assignment mentioned directly above does not inlcude booting from
floppy drive B. This function is useful if floppy drives B and A are of a different
format and you want to boot from floppy drive B.
Boot up Floppy Seek
During POST, BIOS will determine if the installed floppy disk drive has 40 or 80
tracks. A 360K drive has 40 tracks and 720K, 1.2M and 1.44M drives have 80 tracks.
All modern floppy disk drives have 80 tracks.
Boot Up NumLock Status
This function defines the keyboard's numberpad as number keys or arrow keys.
D. Gate A 20 Option
Gate A20 refers to the way the system addresses memory above 1 MB (extended
memory). When set to Fast, the system chipset controls Gate A20. When set to
Normal, a pin in the keyboard controller controls Gate A20. Setting Gate A20 to
Fast improves system speed, particularly with OS/2 and Windows.
16
Award BIOS Setup Program
E. Keyboard Interface
Typematic Rate Setting
When enabled, you can set the following two typematic control items. When
disabled, keystrokes are determined arbitrarily by the keyboard controller in your
system.
Typematic Rate (Chars/Sec)
The typematic rate sets the rate at which characters on the screen repeat when
a key is pressed and held down.
Typematic Delay (Msec)
The typematic delay sets how long after you press a key that a character begins
repeating.
F. Security Option
The Supervisor and/or User Password functions shown in Figure 3-1 must be set
to take advantage of this function. See Section 3-11 for password setting
information. When the Security Option is set to System, a password must be
entered to boot the system or enter the BIOS setup program. When the Security
Option is set to Setup, a password is required to enter the BIOS setup program.
G. OS Select (For DRAM > 64MB)
If your system's DRAM is larger than 64MB and you are running OS/2, select
OS/2 as the item value. Otherwise, set the item value to Non-OS/2 for all other
operating systems.
H. HDD Instant Recovery
This board supports HDD Instant Recovery, select enabled to use this function.
Upon system boot up, the HDD Instant Recovery Utility will be shown on the
screen. Selet Install or Do Not Install to continue booting (See Appendix II).
17
User's Manual
3-3 Advance Chipset Features
By choosing the Advanced Chipset Features option from the Standard CMOS Features
menu(Figure 3-1), the screen below is displayed. This sample screen contains the
manufacturer's default values for the mainboard.
CMOS Setup Utility- Copyright (C) 1984-2001 Award Software
Advanced Chipset Features
DRAM Timing Selectable
CAS Latency Time
Active to Precharge Delay
DRAM RAS# to CAS# Delay
DRAM RAS# Precharge
DRAM Data Integrity Mode
Memory Frequency For
System BIOS Cacheable
Video BIOS Cacheable
Video RAM Cacheable
Memory Hole At 15M-16M
Delayed Transaction
AGP Aperture Size (MB)
Delay Prior to Thermal
Flash BIOS Protection
:Move Enter:Select
F5:Previous Values
By SPD
2.5
7
3
3
Non-ECC
Auto
Disabled
Disabled
Disabled
Disabled
Enabled
64
16 Min
Disabled
Item Help
Menu Level
+/-/PU/PD:Value
F10:Save
ESC:Exit
F1:General Help
F6:Fail-Safe Defaults
F7:Optimized Defaults
Figure 3-4 Advanced Chipset Features Screen
All of the above settings have been determined by the mainboard manufacturer
and should not be changed unless you are absolutely sure of what you are
doing. Explanation of the DRAM timing and chipset features setup is lengthy,
highly technical and beyond the scope of this manual. Below are abbreviated
descriptions of the functions in this setup menu. You can look on the world
wide web for helpful chipset and RAM configuration information including
AWARD's web site at http://www.award.com.
A. Memory Hole at 15M-16M
Enabling this function will reserve the memory address space between 15MB and
16MB for ISA expansion cards. The default setting is Disabled.is enabled.
B. AGP Aperture Size
Select the size of Accelerated Graphics Port (AGP) aperture. The aperture is a portion
of the PCI memory address range dedicated for graphics memory address space. Host
cycles that hit the aperture range are forwarded to the AGP without any translation.
18
Award BIOS Setup Program
3-4 Integrated Peripherals
This section provides information on setting peripheral devices. By choosing the
Integrated Peripherals option from the Standard CMOS Features menu (Figure 3-1),
the screen below is displayed. This sample screen contains the manufacturer's default
values for the mainboard.
CMOS Setup Utility- Copyright (C) 1984-2001 Award Software
Integrated Peripherals
OnChip IDE Device
OnChip PCI Device
SuperIO Device
USB Controller
USB Keyboard Support
Init Display First
:Move Enter:Select
F5:Previous Values
Press Enter
Press Enter
Press Enter
Enabled
Disabled
AGP
Item Help
Menu Level
+/-/PU/PD:Value
F10:Save
ESC:Exit
F1:General Help
F6:Fail-Safe Defaults
F7:Optimized Defaults
Figure 3-5 Integrated Peripherals Screen
A. OnChip IDE Device
On-chip Primary/Secondary PCI IDE
You can set this to disable the On-chip IDE controller if you are going to add
a higher performance IDE board.
IDE Primary/Secondary Master/Slave PIO
The four IDE PIO (programmed Input/Output) fields let you set a PIO mode (04) for each IDE device that the internal PCI IDE interface supports. Modes 0 through
4 provide successively increased performance. In Auto mode, the system
automatically determines the best mode for each device.
B. OnChip IDE Device
AC97 Audio
Select Enabled if you install the audio riser card.
AC97 Modem
Select Enabled if you install the soft modem riser card.
19
User's Manual
C. Super IO Device
Onboard FDC Controller
Select Enabled if your system has a floppy disk controller (FDC) installed on the
system board and you wish to use it. If you install an add-in FDC or the system
has no floppy drive, select Disabled in this field.
UART Mode Select
This function allows you to select an operating mode for the second serial port.
(Normal RS-232C serial port/IrDA/ASKIR/SCR infrared port)
Onboard Parallel Port
Select a logical LPT port address and corresponding interrupt for the physical
parallel port.
D. USB Controller
Enable the on-board Universal Serial Bus (USB) controller if you want to connect
a USB keyboard to your system. Note that if this setting is disabled, you can
still temporarily use a USB keyboard during bootup so that you can enter BIOS
and enable this setting. If you pass the bootup stage without enabling this
function, your PS/2 keyboard will no longer work.
E. USB Keyboard Support
If your current operating system doesn't support USB drivers (i.e., DOS) this
function must be enabled for USB keyboard operation in these operating systems.
F. Init Display First
This function allows user to choose between AGP slot or VGA slot to initialise
Display first .
20
Award BIOS Setup Program
3-5 Power Management Setup
This section provides information on the Green PC power management funtcions. By
choosing the Power Management Setup option from the Standard CMOS Features
menu (Figure 3-1), the screen below is displayed. This sample screen contains the
manufacturer's default values for the mainboard
CMOS Setup Utility- Copyright (C) 1984-2001 Award Software
Power Management Setup
ACPI Function
ACPI Suspend Type
Power Management
Video Off Method
Video Off In Suspend
Suspend Type
MODEM Use IRQ
Suspend Mode
HDD Power Down
Soft-Off by PWR-BTTN
Enabled
S1(POS)
User Define
DPMS
Yes
Stop Grant
3
Disabled
Disabled
Instant-Off
Item Help
Menu Level
** Reload Global Timer Events **
Primary IDE 0
Disabled
Primary IDE 1
Disabled
Secondary IDE 0
Disabled
Secondary IDE 1
Disabled
FDD,COM,LPT Port
Disabled
PCI PIRQ[A-D]#
Disabled
Press Enter
Wake Up Events
:Move Enter:Select
F5:Previous Values
+/-/PU/PD:Value
F10:Save
ESC:Exit
F1:General Help
F6:Fail-Safe Defaults
F7:Optimized Defaults
Figure 3-6 Power Management Setup Screen
A. Advanced Configuration Power Interface (ACPI)
ACPI management enables the operating system to control the amount of power
given to each device attached to the computer. With ACPI, the operating system
can turn off peripherals devices, such as CD-ROM players, when they are not
in use.
B. Power Management
Power management allows the computer to save electricity when it is not in use
by entering increasingly deep power saving modes.
C. Video Off Method
This function serves as both a screen saver and power saver for monitors.
See the next function, Video Off After, for setting the video timer.
21
User's Manual
Blank - BIOS will only blank the monitor's screen. The electricity saved in
this mode is negligible and this function is only used as a screen saver to
prevent screen damage while the screen is on but not in use.
V/H SYNC+Blank - The system turns off the vertical and horizontal synchronization ports, writes blanks to the VGA buffer and the monitor's electron gun
turns off. This function requires a monitor with Green features in order to
take advantage of the power saving function. If you enable this function and
do not have a Green monitor, the result will be the same as if you had selected
Blank. This function serves as both a screen saver and an electricity saver.
DPMS Supported - Select this option if your video card supports the Display
Power Management Signaling (DPMS) standard (i.e., you have a monitor that
supports Green features). Use software supplied by your your video subsystem to set video power management options.
D. Video Off In Suspend
This setting determines when the monitor enters power saving mode. If set to
Yes, the monitor enters the power saving mode after the chosen event expires.
The Power Management function must be enabled to use this function.
E. Modem Use IRQ
If your computer has an modem, use this function to tell BIOS which IRQ is being
occupied by the modem card. When the system is in Green mode, the modem
requires an IRQ assignment to wake up the system and perform tasks. This
assignment is compliant with the APM 1.2 specification and is to be used in
coordination with APM 1.2 compliant operating systems.
F. Suspend Mode
The Power Management function must not be set to disabled to enable this
function. If the system runs in Standby mode and the Suspend timer expires, all
devices regulated by power management will shut off and the CPU speed will be
0 MHz.
G. HDD Power Down
The Power Management function must not be set to disabled to enable this
function. When the HDD idle time has elapsed, BIOS sends a command to the
hard disk to turn off the motor. Set a time between 1 and 15 to indicate time required
to wait before the hard drive enters a power saving mode. Some old hard drives
may not support this function.
22
Award BIOS Setup Program
H. Soft-Off by PWR-BTTN
When set to Delay 4 Sec., this function allows the power button to put the system
in Suspend, a power saving mode. See Section 2-4 for operation instructions of
the over-ride power button operation wich puts the system in Suspend mode.
When set to Instant-Off the Soft-Off by PWR-BTTN function is disabled and the
computer turns completely off when the power button is pressed.
I. Wake Up Events
Power On By Modem
When enabled, a modem that receives a ring signal will wake up the system from
soft off and green mode. You should connect the modem to the COM port
and turn on the resume event in green mode.
Resume By Alarm
When enabled, this setting allows the system to turn back on at a designated
time of the month. User must designate date of month and time of day. This
function is only available when using an ATX power supply and the Software
Power-Off function to turn off the computer. See the Software Power-Off Control
in Section 2-4 of this manual for instructions.
Power On Function
Select Button Only to control your computer power by the button on your system
case. Set this function to Any Key to turn on the computer by touching any key
on the keyboard. Set this function to Mouse Click to turn on the computer by
clicking on the mouse. If you set this function to Hot Key or Password you must
designate the keystrokes that will turn on the computer. Note that the power button
is always able to turn on the computer regardless of how this function is set.
23
User's Manual
3-6 PNP/PCI Configuration
This section provides IRQ and DMA setting information. By choosing the PNP/PCI
Configuration option from the Standard CMOS Features menu (Figure 3-1), the screen
below is displayed. This sample screen contains the manufacturer's default values
for the mainboard.
CMOS Setup Utility- Copyright (C) 1984-2001 Award Software
PnP/PCI Configurations
Reset Configuration Data
Resources Controlled By
x IRQ Resources
PCI/VGA Palette Snoop
Slot 1 Use IRQ No.
Slot 2 Use IRQ No.
Slot 3 Use IRQ No.
FDD IRQ Can Be Free
:Move Enter:Select
F5:Previous Values
Disabled
Auto(ESCD)
Press Enter
Item Help
Menu Level
Disabled
Auto
Auto
Auto
Yes
+/-/PU/PD:Value
F10:Save
ESC:Exit
F1:General Help
F6:Fail-Safe Defaults
F7:Optimized Defaults
Figure 3-7 PnP/PCI Configurations Screen
A. Resources Controlled By
When set to Manual the system BIOS will not refer to the ESCD for IRQ & DMA
information. Instead, it will refer to the items in the setup menu for assigning IRQ
& DMA. When set to Auto the system BIOS will refer to the ESCD for all legacy
information.
ESCD(Extended System Configuration Data) provides a detailed format of
the configuration data structures stored in flash memory. Each data structure
defines the resources used by a device or a card in the system. This includes
legacy and PCI/ISA PnP devices.
B. FDD IRQ Can Be Free
This function allows user to choose if the FDD IRQ is able to be freed up. The
default setting is Yes and this does not allow the IRQ to be free.
24
Award BIOS Setup Program
3-7 PC Health Status
By choosing the PC Health Status option from the CMOS Setup Utility menu (Figure
3-1), the screen below is displayed. This field shows you the current system
temperature/external voltages input and the current CPU FAN and System FAN
operating speed.
CMOS Setup Utility- Copyright (C) 1984-2001 Award Software
PC Health Status
Shutdown Temperature
CPU VCore
+1.5V
+3.3V
+5V
+ 12V
- 12V
-5V
5VSB(V)
Voltage Battery
Current SYSTEM Temp.
Current CPU Temp.
Current CPU FAN Speed.
Current SYSTEM FAN Speed.
75oC/167oF
1.75V
1.49V
3.32V
5.05V
12.18V
-11.98V
-5.02
4.89V
2.98V
48 oC
48 oC
4500 RPM
4500 RPM
Item Help
Menu Level
: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
Figure 3-8 PC Health Status Screen
3-8 SeePU Setup
By choosing the Frequency/Voltage Control option from the CMOS Setup Utility
menu (Figure 3-1), the screen below is displayed. This sample screen contains the
manufacturer's default values for the mainboard.
CMOS Setup Utility- Copyright (C) 1984-2001 Award Software
Frequency/Voltage Control
CPU Clock Ratio
Auto Detect PCI Clk
Linear Spread Model
Linear Spread Model Base
Linear Spread Range
CPU Clock
X8
Enabled
4
4
4
100 MHz
Item Help
Menu Level
: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
Figure 3-9 Frequency/Voltage Control Screen
A. CPU Clock Ratio
This feature allows user to manually configure your CPU clock ratio according
to your processor's specifications.
B. CPU Clock
This feature allows the system memory to run at CPU clock speed. The default
setting is at 100MHz.
25
User's Manual
3-9 Load Fail-Safe Defaults
Load Fail-Safe Defaults loads the default BIOS values directly from the CMOS Setup
Utility menu (Figure3-1). If the stored record created by the setup program becomes
corrupted and therefore unusable, these defaults will be loaded automatically when
you turn on the computer.
CMOS Setup Utility- Copyright (C) 1984-2001 Award Software
Standard CMOS Features
Frequency/Voltage Control
Advanced BIOS Features
Load Fail-Safe Defaults
Advanced Chipset Features
Load Optimized Defaults
Integrated Peripherals
Set Supervisor Password
Power Management Setup
Set User Password
PnP/PCI Configur
PC Health Status
Setup
Load Fail-Safe Defaults (Y/N) ? N
Esc
: Quit
F10 : Save & Exit Setup
Saving
: Select Item
Load Fail-Safe Defaults
Figure 3-10 Load Fail-Safe Defaults Screen
3-10 Load Optimized Defaults
Load Optimized Defaults loads the default system values directly from the CMOS
Setup Utility menu (Figure3-1). If the stored record created by the setup program
becomes corrupted and therefore unusable, these defaults will be loaded automatically
when you turn on the computer.
CMOS Setup Utility- Copyright (C) 1984-2001 Award Software
Standard CMOS Features
Frequency/Voltage Control
Advanced BIOS Features
Load Fail-Safe Defaults
Advanced Chipset Features
Load Optimized Defaults
Integrated Peripherals
Set Supervisor Password
Power Management Setup
Set User Password
PnP/PCI Configur
PC Health Status
Setup
Load Optimized Defaults (Y/N) ? N
Esc
: Quit
F10 : Save & Exit Setup
Saving
: Select Item
Load Optimized Defaults
Figure 3-11 Load Optimized Defaults Screen
26
Award BIOS Setup Program
3-11 Supervisor Password & User Password Setting
There are four different variables that control password settings. The first two are
located under the Security Option function in BIOS Features Setup Menu (Figure
3-1). When the Security Option function is set to Setup, a password is required to
enter BIOS and change BIOS settings. When the Security Option function is set
to System, a password is required to enter both BIOS and the computer's operating
system (for example Windows 98) found on the boot drive.
The third and fourth variables are user password and supervisor password selected
in BIOS (Figure 3-1). The main purpose of separating user and supervisor is to allow
only the supervisor to have control over the settings in BIOS. The user, on the other
hand, is only allowed to access the computer's operating system and change the user
password in BIOS. Note that when there is no supervisor password set, the user
password controls access to all BIOS settings.
3-12 Save and Exit Setup
If you select this and type Y (for yes) followed by the [Enter] key, the values entered
in the setup utilities will be recorded in the CMOS memory of the BIOS chip.
3-13 Exit Without Saving
Selecting this option and pressing Y followed by the [Enter] key lets you exit the
Setup program without recording any new values or changing old ones.
27
Appendix I
Embedded Flash Utility
This mainboard is equipped with an Erasable Flash ROM and an Embedded
Flash Utility which allows the user to update the BIOS to a newer version.
Embedded Flash Utility eases BIOS upgrade and eliminate the compatibility
issue between different Flash ROM type and version of Flash utility.
Update Your System BIOS
1. Start computer, upon post, press ALT+F2 Keys to enter AWDFLASH setup.
2. Insert the floppy disk with the latest BIOS file into the floppy drive A(or B)
and then press Enter to start programming.
FLASH MEMORY WRITER V 7.52C
(C) Award Software 2001 All Right Reserved
For XXX-XXXXXXX-6A69MC3DC-0 DATE: 06/20/2000
Flash Type- XXXXX E82802AB / 3.xV(1Mb)
File Name to Program : 9BIA0704.BIN
Programming
Flash Memory
1234567890123456789012345
1234567890123456789012345
1234567890123456789012345
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
1234567890123456789012345678901212345678901234567
1234567890123456789012345678901212345678901234567
12 1234567890123456789012345678901212345678901234567
1234567890123456789012345678901212345678901234567
123
123
12 Write OK
123
123
123
123No Update
12
123 Write Fail
Warning : Don't Turn Off Power Or Reset System !
Sample of Programing Flash Memory Screen
3. When finished, the system will automatically restart.
Note:
( Flash BIOS Protection must be set to Disabled in the Advance Chipset
Feature from the CMOS Setup Utility menu. See Chapter 3.
( Don't turn off or restart your system during programming process.
( Make sure that your floppy diskette have only one BIN file to avoid
confusion.
28
Appendix II
HDD Instant Recovery Utility
This mainboard is equipped with HDD Instant Recovery utility embedded in the
BIOS ROM. The feature is an option which allows the user to install or not. HDD
Instant Recovery utility is a Pre-O.S. backup technology that provides backup before
any OS is being activated. Just one press on the Hotkey, HDD Instant Recovery can
revive your system even if your O.S. crashed or not working properly.
❒ HDD Instant Recovery Concept
HDD IR will save your vital O.S. and application software in a hidden space inside
the same hard drive. Since the backup file occupies some space in the hidden
directory, the displayed disk space will be reduced. HDD IR will backup your
system either with the Smart or Equivalent Backup depends on your O.S. type.
Smart Backup (FAT16/32 format i.e.Win 95/98 O.S.)
- Backup space is the actual system space used.
Equivalent Backup (NTFS format i.e.Windows 2000/NT.)
- Backup space equivalent to the drive space where the O.S. located.
❒ Utility Installation
1. Enable the HDD Instant Recovery in the BIOS Features setup from the CMOS
Setup Utility menu. Save and exit to reboot.
2. Upon system boot up, the HDD Instant Recovery Utility will be shown on the
screen. Selet Install and press Enter key to read the instruction.
3. Press F8 key to continue, you will be prompt to confirmed to keep original
data.
4. Type Y and press Enter and wait for the installation process to finish and the
system will automatically reboot.
HDD Instant Recovery Utility
<Alt-F1>: Backup System
<Alt-F2>: Disk Information
<Alt-F3>: Restore System
<Alt-F4>: Defragmenter
<Alt-F5>: Hard Disk Copy
<Alt-F6>: Uninstall
HDD Instant Recovery Utility Setup screen
29
H Backup System
Smart Backup
1. Upon system boot up, the HDD Instant Recovery Utility will be shown on
the screen. Selet Backup System by pressing Alt+F1 key.
2. Select your hard drive to backup.
3. Wait for the backup process to finish and the system will automatically reboot.
Equivalent Backup
( Still under evaluation testing for future Windows 2000/NT supports.
H Disk Information
1. Upon system boot up, the HDD Instant Recovery Utility will be shown on
the screen. Select Disk Information by pressing Alt+F2 key to view Disk Info.
H Restore System
1. Upon system boot up, the HDD Instant Recovery Utility will be shown on
the screen. Selet Restore System by pressing Alt+F3 key.
2. You will be prompt to confirmed restore drive. Type Y and press Enter key.
3. Wait for the backup process to finish and the system will automatically reboot.
H Defragmenter
1. Upon system boot up, the HDD Instant Recovery Utility will be shown on
the screen. Selet Defragmenter by pressing Alt+F4 key.
2. You will be prompt to confirmed defragment your drive. Type Y and press
Enter key.
3. Wait for the defrgmentation process to finish and the system will automatically
reboot.
H Hard Disk Copy
1. Upon system boot up, the HDD Instant Recovery Utility will be shown on
the screen. Selet Hard Disk Copy by pressing Alt+F5 key.
2. Select which hard drive to backup.(Copy 1 to 2 or 2 to 1 or 1 to 2 3 4)
3. Wait for the hard disk copy process to finish and the system will auto reboot.
H Uninstall
1. Upon system boot up, the HDD Instant Recovery Utility will be shown on
the screen. Selet uninstall by pressing Alt+F6 key.
2. You will be prompt to confirmed uninstall. Type Y and press Enter key.
3. Wait for the uninstalling process to finish and press any key to reboot
This function does not support Multi-Booting management utility like
System Commander, etc.
Always uninstall this function before you format or partition the hard disk
for other usage.
30

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement