null  null
For Parts Call K&T 606-678-9623 or 606-561-4983
OWNER'S MANUAL
MODEL NO. SGT18H46C
18.0 HP 46 Inch
Lawn Tractor
For Parts and Service, contact our authorized distributor: call 1-800-849-1297
For Technical Assistance: call 1-800-829-5886
®
178387 4.6.01 TR
PRINTED IN U.S.A.
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
SAFETY RULES
SAFE OPERATION PRACTICES FOR RIDE-ON MOWERS
IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS.
FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.
I. GENERAL OPERATION
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Avoid starting or stopping on a slope. If tires lose traction,
disengage the blades and proceed slowly straight down
the slope.
DO NOT:
• Do not turn on slopes unless necessary, and then, turn
slowly and gradually downhill, if possible.
• Do not mow near drop-offs, ditches, or embankments.
The mower could suddenly turn over if a wheel is over the
edge of a cliff or ditch, or if an edge caves in.
• Do not mow on wet grass. Reduced traction could cause
sliding.
• Do not try to stabilize the machine by putting your foot on
the ground.
• Do not use grass catcher on steep slopes.
Read, understand, and follow all instructions in the manual
and on the machine before starting.
Only allow responsible adults, who are familiar with the
instructions, to operate the machine.
Clear the area of objects such as rocks, toys, wire, etc.,
which could be picked up and thrown by the blade.
Be sure the area is clear of other people before mowing.
Stop machine if anyone enters the area.
Never carry passengers.
Do not mow in reverse unless absolutely necessary.
Always look down and behind before and while backing.
Be aware of the mower discharge direction and do not point
it at anyone. Do not operate the mower without either the
entire grass catcher or the guard in place.
Slow down before turning.
Never leave a running machine unattended. Always turn
off blades, set parking brake, stop engine, and remove
keys before dismounting.
Turn off blades when not mowing.
Stop engine before removing grass catcher or unclogging
chute.
Mow only in daylight or good artificial light.
Do not operate the machine while under the influence of
alcohol or drugs.
Watch for traffic when operating near or crossing roadways.
Use extra care when loading or unloading the machine into
a trailer or truck.
Data indicates that operators, age 60 years and above, are
involved in a large percentage of riding mower-related
injuries. These operators should evaluate their ability to
operate the riding mower safely enough to protect themselves and others from serious injury.
Keep machine free of grass , leaves or other debris buildup which can touch hot exhaust / engine parts and burn.
Do not allow the mower deck to plow leaves
or other debris which can cause build-up to occur. Clean
any oil or fuel spillage before operating or storing the
machine. Allow machine to cool before
storage.
III. CHILDREN
Tragic accidents can occur if the operator is not alert to the
presence of children. Children are often attracted to the
machine and the mowing activity. Never assume that children
will remain where you last saw them.
• Keep children out of the mowing area and under the
watchful care of another responsible adult.
• Be alert and turn machine off if children enter the area.
• Before and when backing, look behind and down for small
children.
• Never carry children. They may fall off and be seriously
injured or interfere with safe machine operation.
• Never allow children to operate the machine.
• Use extra care when approaching blind corners, shrubs,
trees, or other objects that may obscure vision.
IV. SERVICE
•
•
•
II. SLOPE OPERATION
Slopes are a major factor related to loss-of-control and tipover
accidents, which can result in severe injury or death. All slopes
require extra caution. If you cannot back up the slope or if you feel
uneasy on it, do not mow it.
•
•
DO:
• Mow up and down slopes, not across.
• Remove obstacles such as rocks, tree limbs, etc.
• Watch for holes, ruts, or bumps. Uneven terrain could
overturn the machine. Tall grass can hide obstacles.
• Use slow speed. Choose a low gear so that you will not
have to stop or shift while on the slope.
• Follow the manufacturer’s recommendations for wheel
weights or counterweights to improve stability.
• Use extra care with grass catchers or other attachments.
These can change the stability of the machine.
• Keep all movement on the slopes slow and gradual. Do
not make sudden changes in speed or direction.
•
•
•
•
•
2
Use extra care in handling gasoline and other fuels. They
are flammable and vapors are explosive.
- Use only an approved container.
- Never remove gas cap or add fuel with the engine
running. Allow engine to cool before refueling. Do not
smoke.
- Never refuel the machine indoors.
- Never store the machine or fuel container inside where
there is an open flame, such as a water heater.
Never run a machine inside a closed area.
Keep nuts and bolts, especially blade attachment bolts,
tight and keep equipment in good condition.
Never tamper with safety devices. Check their proper
operation regularly.
Keep machine free of grass, leaves, or other debris buildup. Clean oil or fuel spillage. Allow machine to cool before
storing.
Stop and inspect the equipment if you strike an object.
Repair, if necessary, before restarting.
Never make adjustments or repairs with the engine
running.
Grass catcher components are subject to wear, damage,
and deterioration, which could expose moving parts or
allow objects to be thrown. Frequently check components
and replace with manufacturer's recommended parts,
when necessary.
Mower blades are sharp and can cut. Wrap the blade(s)
or wear gloves, and use extra caution when servicing
them.
Check brake operation frequently. Adjust and service
as required.
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
SAFETY RULES
Safe Operation Practices for Ride-On Mowers
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Look for this symbol to point out important safety precautions. It means
CAUTION!!! BECOME ALERT!!! YOUR
SAFETY IS INVOLVED.
Be sure the area is clear of other people before mowing. Stop
machine if anyone enters the area.
Never carry passengers or children even with the blades off.
Do not mow in reverse unless absolutely necessary. Always
look down and behind before and while backing.
Never carry children. They may fall off and be seriously
injured or interfere with safe machine operation.
Keep children out of the mowing area and under the watchful
care of another responsible adult.
Be alert and turn machine off if children enter the area.
Before and when backing, look behind and down for small
children.
Mow up and down slopes (15° Max), not across.
Remove obstacles such as rocks, tree limbs, etc.
Watch for holes, ruts, or bumps. Uneven terrain could overturn the machine. Tall grass can hide obstacles.
Use slow speed. Choose a low gear so that you will not have
to stop or shift while on the slope.
Avoid starting or stopping on a slope. If tires lose traction,
disengage the blades and proceed slowly straight down the
slope.
If machine stops while going uphill, disengage blades, shift
into reverse and back down slowly.
Do not turn on slopes unless necessary, and then, turn slowly
and gradually downhill, if possible.
CAUTION: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and
place wire where it cannot contact spark
plug.
CAUTION: Do not coast down a hill in
neutral, you may lose control of the
tractor.
CAUTION: Tow only the attachments
that are recommended by and comply
with specifications of the manufacturer
of your tractor. Use common sense
when towing. Operate only at the lowest possible speed when on a slope.
Too heavy of a load, while on a slope,
is dangerous. Tires can lose traction
with the ground and cause you to lose
control of your tractor.
WARNING
Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals
known to the State of California to cause cancer and
birth defects or other reproductive harm.
WARNING
Battery posts, terminals and related accessories
contain lead and lead compounds, chemicals known
to the State of California to cause cancer and birth
defects or other reproductive harm. Wash hands
after handling.
3
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
PRODUCT SPECIFICATIONS
GASOLINE CAPACITY
AND TYPE:
3.5 GALLONS
UNLEADED REGULAR
OIL TYPE (API-SF-SJ):
SAE 30 (above 32°F)
SAE 5W-30 (below 32°F)
OIL CAPACITY:
W/FILTER: 5 PINTS
W/O FILTER: 4.5 PINTS
SPARK PLUG:
(GAP: .030")
CHAMPION RN4C
GROUND SPEED (MPH):
FORWARD:
REVERSE:
5.5
2.4
TIRE PRESSURE:
FRONT:
REAR:
14 PSI
10 PSI
CHARGING SYSTEM:
CONGRATULATIONS on your purchase of a new tractor. It
has been designed, engineered and manufactured to give
you the best possible dependability and performance.
Should you experience any problem you cannot easily
remedy, please contact your nearest authorized service
centre/department. We have competent, well-trained technicians and the proper tools to service or repair this tractor.
Please read and retain this manual. The instructions will
enable you to assemble and maintain your tractor properly.
Always observe the “SAFETY RULES”.
CUSTOMER RESPONSIBILITIES
•
•
•
3 AMPS BATTERY
5 AMPS HEADLIGHTS
BATTERY:
AMP/HR:
MIN. CCA:
CASE SIZE:
BLADE BOLT TORQUE:
27-35 FT. LBS.
Read and observe the safety rules.
Follow a regular schedule in maintaining, caring for and
using your tractor.
Follow the instructions under “Customer Responsibilities” and “Storage” sections of this owner’s manual.
WARNING: This tractor is equipped with an internal combustion engine and should not be used on or near any
unimproved forest-covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped
with a spark arrester meeting applicable local or state laws
(if any). If a spark arrester is used, it should be maintained
in effective working order by the operator.
A spark arrester for the muffler is available through your
nearest authorized service centre/department (See REPAIR PARTS section of this manual).
30
240
U1R
TABLE OF CONTENTS
SERVICE AND ADJUSTMENTS ............................. 20-24
STORAGE ................................................................... 25
TROUBLESHOOTING ............................................. 26-27
REPAIR PARTS - TRACTOR .................................. 30-45
WARRANTY ................................................................ 46
SAFETY RULES ........................................................ 2-3
PRODUCT SPECIFICATIONS ....................................... 4
CUSTOMER RESPONSIBILITIES ...................... 4, 16-19
ASSEMBLY ................................................................ 6-9
OPERATION ............................................................ 10-15
MAINTENANCE SCHEDULE ....................................... 16
4
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
UNASSEMBLED PARTS
Steering Wheel
Seat
(1) Washer
17/32 x 1-3/16 x 12 Gauge
(1) Knob
Nose Roller
Steering
Wheel Insert
Gauge Wheels
(2) Washers
17/32 x 7/8 x 16 Ga.
(2) Gauge
Wheels
(2) Locknuts
5/16-18
(2) Washers 3/8
x 7/8 x 14 Gauge
Nose
Roller
Brackets
(2) Shoulder
Bolts
(2) Hex Bolts
5/16-18 x 1
(2) Centerlock Nuts
Mower
(1) Oil Drain Tube
For Future Use
(2) Front Link Assemblies
Key
Slope Sheet
(2) Keys
(3) Retainer Springs
(double loop)
(4) Retainer Springs (single loop)
Slope Sheet
5
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
ASSEMBLY
Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To
ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the
correct tools as necessary to insure proper tightness.
TOOLS REQUIRED FOR ASSEMBLY
STEERING
WHEEL INSERT
A socket wrench set will make assembly easier. Standard
wrench sizes are listed.
(2) 9/16" wrench
Pliers
(2) 1/2" wrenches
Tire pressure gauge
(1) 3/4" Socket w/drive ratchet Utility knife
LOCKNUT
LARGE
FLAT
WASHER
STEERING
WHEEL
When right or left hand is mentioned in this manual, it means
when you are in the operating position (seated behind the
steering wheel).
TO REMOVE TRACTOR FROM CARTON
UNPACK CARTON
•
•
•
•
STEERING
WHEEL
ADAPTER
Remove all accessible loose parts and parts cartons
from carton.
Cut, from top to bottom, along lines on all four corners
of carton, and lay panels flat.
Remove mower and packing materials.
Check for any additional loose parts or cartons and
remove.
STEERING SHAFT
STEERING
SLEEVE
BEFORE REMOVING TRACTOR FROM
SKID
FIG. 1
ATTACH STEERING WHEEL (See Fig. 1)
•
•
•
•
•
•
Remove locknut and large flat washer from steering
shaft.
Position front wheels of the tractor so they are pointing
straight forward.
Position steering wheel so cross bars are horizontal (left
to right) and slide onto adapter.
Secure steering wheel to steering shaft with locknut and
large flat washer previously removed. Tighten securely.
Snap steering wheel insert into center of steering wheel.
Remove protective materials from tractor hood and grill.
HOW TO SET UP YOUR TRACTOR
CHECK BATTERY (See Fig. 2)
•
•
Lift hood to raised position.
If this battery is put into service after month and year
indicated on label (label located between terminals)
charge battery for minimum of one hour at 6-10 amps.
(See "BATTERY" in CUSTOMER RESPONSIBILITIES
section of this manual for charging instructions).
IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES
IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR
IS TO ROLL OFF SKID.
LABEL
FIG. 2
6
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
ASSEMBLY
INSTALL SEAT (See Fig. 3)
TO ROLL TRACTOR OFF SKID (See Operation
section page 11 for location and function of
controls)
Adjust seat before tightening adjustment knob.
• Remove adjustment knob and flat washer securing seat
to cardboard packing and set aside for assembly of seat
to tractor.
• Pivot seat upward and remove from the cardboard
packing. Remove the cardboard packing and discard.
• Place seat on seat pan so head of shoulder bolt is
positioned over large slotted hole in pan.
• Push down on seat to engage shoulder bolt in slot and
pull seat towards rear of tractor.
• Pivot seat and pan forward and assemble adjustment
knob and flat washer loosely. Do not tighten.
• Lower seat into operating position and sit on seat.
• Slide seat until a comfortable position is reached which
allows you to press clutch/brake pedal all the way down.
• Get off seat without moving its adjusted position.
• Raise seat and tighten adjustment knob securely.
•
•
•
•
Press lift lever plunger and raise attachment lift lever to
its highest position.
Release parking brake by depressing clutch/brake pedal.
Place freewheel control in freewheeling position to
disengage transmission (See “TO TRANSPORT” in the
Operation section of this manual).
Roll tractor forward off skid.
TO DRIVE TRACTOR OFF SKID (See Operation section page 11 for location and function
of controls)
WARNING: Before starting, read, understand and follow
all instructions in the Operation section of this manual. Be
sure tractor is in a well-ventilated area. Be sure the area in
front of tractor is clear of other people and objects.
• Be sure all the above assembly steps have been
completed.
• Check engine oil level and fill fuel tank with gasoline.
• Place freewheel control in "transmission engaged" position.
• Sit on seat in operating position, depress clutch/brake
pedal and set the parking brake.
• Place motion control lever in neutral (N) position.
• Press lift lever plunger and raise attachment lift lever to
its highest position.
• Start the engine. After engine has started, move throttle
control to idle position.
• Release parking brake.
• Slowly move the motion control lever forward and slowly
drive tractor off skid.
• Apply brake to stop tractor, set parking brake and place
motion control lever in neutral position.
• Turn ignition key to "OFF" position.
Continue with the instructions that follow.
SEAT
SEAT PAN
SHOULDER
BOLT
FLAT WASHER
TO ATTACH NOSE ROLLER (See Fig. 4)
•
Position brackets, 17/32 x 7/8 x 16 gauge washers, and
nose roller between deck mounting brackets as shown.
Be sure to position brackets on correct side, as shown.
• Install hex bolts and lock nuts as shown. Tighten
hardware securely.
NOTE: Be sure bracket tabs are positioned in tab holes in
deck brackets.
ADJUSTMENT
KNOB
FIG. 3
NOTE: You may now roll or drive your tractor off the skid.
Follow the appropriate instruction below to remove the
tractor from the skid.
TAB
HOLE
“A” BRACKET
TAB
NOSE ROLLER
HEX
BOLT
LOCK NUT
“B”
BRACKET
TAB
WASHER
FIG. 4
7
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
ASSEMBLY
•
INSTALL MOWER AND DRIVE BELT
(See Figs. 5 and 6)
Be sure tractor is on level surface and mower suspension
arms are raised with attachment lift control. Engage parking
brake.
• Cut and remove ties securing anti-sway bar and belts.
Swing anti-sway bar to left side of mower deck.
• Slide mower under tractor with deflector shield to right
side of tractor.
•
•
IMPORTANT: CHECK BELT FOR PROPER ROUTING IN
ALL MOWER PULLEY GROOVES. INSTALL BELT INTO
ENGINE PULLEY GROOVE.
•
•
•
•
Install one front link in top hole of the L.H. front mower
bracket and L.H. front suspension bracket. Retain with
two single loop retainer springs as shown.
Install second front link in R.H. front suspension bracket
only and retain with single loop retainer spring as shown.
Slide right side of mower back and install the unattached
front link in top hole of the R.H. front mower bracket.
Retain with single loop retainer spring as shown.
Lower mower linkage with attachment lift control.
•
•
•
Place the suspension arms on outward pointing deck
pins. If necessary, rock and raise front of mower to align
deck pins with the holes in suspension arms. Retain
with double loop retainer springs with loops down as
shown.
Connect anti-sway bar to chassis bracket under left
footrest and retain with double loop retainer spring.
Install clutch cable:
- Slide collar away from cable housing guide.
- Push housing guide into hole in mounting bracket.
- Slide collar onto housing guide and secure with large
retainer spring.
- Place flat washer and clutch spring on idler pulley bolt
and secure with small retainer spring.
Raise mower to highest position.
Assemble gauge wheels as shown using long shoulder
bolts, 3/8 washers and 3/8-16 center locknuts. Tighten
securely.
Adjust gauge wheels before operating mower as shown
in the Operation section of this manual.
SMALL
RETAINER SPRING
CLUTCH SPRING
COLLAR
LARGE
RETAINER SPRING
FLAT WASHER
ENGINE PULLEY
SUSPENSION ARMS
DOUBLE LOOP
RETAINER SPRING
(Outward pointing
deck pins)
FRONT MOWER
BRACKET
FRONT SUSPENSION
BRACKET
HOUSING
GUIDE
SHOULDER
BOLT
FRONT LINKS
SINGLE LOOP
RETAINER
SPRINGS
GAUGE WHEEL
3/8-16
CENTER
LOCKNUT
3/8 WASHER
USE PLIERS FOR
RETAINER SPRINGS
ANTI-SWAY BAR
DOUBLE LOOP
RETAINER
SPRING
IDLER PULLEY
LOOP
DOWN
DEFLECTOR SHIELD
FIG. 5
8
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
ASSEMBLY
3CHECKLIST
CHECK TIRE PRESSURE
The tires on your tractor were overinflated at the factory for
shipping purposes. Correct tire pressure is important for
best cutting performance.
• Reduce tire pressure to PSI shown in “PRODUCT
SPECIFICATIONS” section of this manual.
BEFORE YOU OPERATE AND ENJOY YOUR NEW TRACTOR, WE WISH TO ASSURE THAT YOU RECEIVE THE
BEST PERFORMANCE AND SATISFACTION FROM THIS
QUALITY PRODUCT.
PLEASE REVIEW THE FOLLOWING CHECKLIST:
3 All assembly instructions have been completed.
3 No remaining loose parts in carton.
3 Battery is properly prepared and charged. (Minimum 1
hour at 6 amps).
3 Seat is adjusted comfortably and tightened securely.
3 All tires are properly inflated. (For shipping purposes,
the tires were overinflated at the factory).
3 Be sure mower deck is properly leveled side-to-side/
front-to-rear for best cutting results. (Tires must be
properly inflated for leveling).
3 Check mower and drive belts. Be sure they are routed
properly around pulleys and inside all belt keepers.
3 Check wiring. See that all connections are still secure
and wires are properly clamped.
3 Before driving tractor, be sure freewheel control is in
drive position.
WHILE LEARNING HOW TO USE YOUR TRACTOR, PAY
EXTRA ATTENTION TO THE FOLLOWING IMPORTANT
ITEMS:
3 Engine oil is at proper level.
3 Fuel tank is filled with fresh, clean, regular unleaded
gasoline.
3 Become familiar with all controls - their location and
function. Operate them before you start the engine.
3 Be sure brake system is in safe operating condition.
3 It is important to purge the transmission before operating
your tractor for the first time. Follow proper starting and
transmission purging instructions (See “TO START
ENGINE” and “PURGE TRANSMISSION” in the Operation section of this manual).
CHECK DECK LEVELNESS
For best cutting results, mower housing should be properly
leveled. See “TO LEVEL MOWER HOUSING” in the Service
and Adjustments section of this manual.
CHECK FOR PROPER POSITION OF ALL
BELTS
See the figures that are shown for replacing motion and
mower blade drive belts in the Service and Adjustments
section of this manual. Verify that the belts are routed
correctly.
CHECK BRAKE SYSTEM
After you learn how to operate your tractor, check to see that
the brake is properly adjusted. See “TO ADJUST BRAKE”
in the Service and Adjustments section of this manual.
9
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
OPERATION
These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning.
BATTERY
CAUTION OR
WARNING
REVERSE
FORWARD
FAST
SLOW
ENGINE ON
ENGINE OFF
OIL PRESSURE
LIGHTS ON
OVER TEMP
LIGHT
FUEL
CHOKE
MOWER HEIGHT
PARKING BRAKE
LOCKED
UNLOCKED
MOWER LIFT
P
ATTACHMENT
CLUTCH ENGAGED
REVERSE
NEUTRAL
HIGH
LOW
PARKING BRAKE
15
IGNITION
ATTACHMENT
CLUTCH DISENGAGED
KEEP AREA CLEAR
15
15
SLOPE HAZARDS
(SEE SAFETY RULES SECTION)
FREE WHEEL
(Automatic Models only)
DANGER, KEEP HANDS AND FEET AWAY
10
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
OPERATION
KNOW YOUR TRACTOR
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR
Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save
this manual for future reference.
ATTACHMENT
CLUTCH LEVER
IGNITION
SWITCH
AMMETER
LIGHT
SWITCH
POSITION
LIFT LEVER
PLUNGER
CHOKE
CONTROL
ATTACHMENT
LIFT LEVER
THROTTLE
CONTROL
CLUTCH/
BRAKE
PEDAL
FREE WHEEL
CONTROL
PARKING
BRAKE
MOTION
CONTROL
LEVER
HEIGHT
ADJUSTMENT
KNOB
FIG. 6
Our tractors conform to the safety standards of the American National Standards Institute.
AMMETER: Indicates charging (+) or discharging (-) of
battery.
MOTION CONTROL LEVER: Selects the speed and
direction of tractor.
ATTACHMENT LIFT LEVER - Used to raise and lower the
mower deck or other attachments mounted to your tractor.
LIFT LEVER PLUNGER: Used to release attachment lift
lever when changing its position.
IGNITION SWITCH: Used for starting and stopping the
engine.
HEIGHT ADJUSTMENT KNOB: Used to adjust the mower
cutting height.
ATTACHMENT CLUTCH LEVER: Used to engage the
mower blades, or other attachments mounted to your tractor.
LIGHT SWITCH: Turns the headlights on and off.
THROTTLE CONTROL: Used to control engine speed.
CHOKE CONTROL: Used when starting a cold engine.
CLUTCH/BRAKE PEDAL: Used for declutching and braking the tractor and starting the engine.
PARKING BRAKE: Locks clutch/brake pedal into the brake
position.
FREEWHEEL CONTROL: Disengages transmission for
pushing or slowly towing the tractor with the engine off.
11
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
OPERATION
The operation of any tractor can result in foreign objects thrown into the eyes, which can
result in severe eye damage. Always wear safety glasses or eye shields while operating
your tractor or performing any adjustments or repairs. We recommend a wide vision
safety mask over spectacles or standard safety glasses.
IMPORTANT: LEAVING THE IGNITION SWITCH IN ANY
POSITION OTHER THAN "OFF" WILL CAUSE THE
BATTERY TO BE DISCHARGED, (DEAD).
HOW TO USE YOUR TRACTOR
TO SET PARKING BRAKE (See Fig. 7)
NOTE: Under certain conditions when tractor is standing
idle with the engine running, hot engine exhaust gases
may cause “browning” of grass. To eliminate this
possibility, always stop engine when stopping tractor on
grass areas.
Your tractor is equipped with an operator presence sensing
switch. When engine is running, any attempt by the operator
to leave the seat without first setting the parking brake will
shut off the engine.
• Depress clutch/brake pedal into full “BRAKE” position
and hold.
• Place parking brake lever in “ENGAGED” position and
release pressure from clutch/brake pedal. Pedal should
remain in “BRAKE” position. Make sure parking brake
will hold tractor secure.
CAUTION: Always stop tractor completely, as described above, before leaving the operator's position; to empty
grass catcher, etc.
TO USE THROTTLE CONTROL (See Fig. 7)
ATTACHMENT
CLUTCH LEVER
"ENGAGED" POSITION
CHOKE
CONTROL
THROTTLE
CONTROL
IGNITION KEY
HEIGHT
ADJUSTMENT
KNOB
"DISENGAGED"
POSITION
Always operate engine at full throttle.
• Operating engine at less than full throttle reduces the
battery charging rate.
• Full throttle offers the best bagging and mower performance.
TO USE CHOKE CONTROL (See Fig. 7)
Use choke control whenever you are starting a cold engine.
Do not use to start a warm engine.
• To engage choke control, pull knob out. Slowly push
knob in to disengage.
PARKING BRAKE
"ENGAGED"
POSITION
"BRAKE"
POSITION
TO MOVE FORWARD AND BACKWARD (See
Fig. 7)
MOTION
CONTROL LEVER
CLUTCH/BRAKE PEDAL
"DRIVE" POSITION
PARKING BRAKE
"DISENGAGED" POSITION
The direction and speed of movement is controlled by the
motion control lever.
• Start tractor with motion control lever in neutral (N)
position.
• Release parking brake and clutch/brake pedal.
• Slowly move motion control lever to desired position.
FIG. 7
STOPPING (See Fig. 7)
MOWER BLADES • To stop mower blades,move attachment clutch lever to
“DISENGAGED” position.
TO ADJUST MOWER CUTTING HEIGHT
(See Fig. 7)
GROUND DRIVE • To stop ground drive, depress clutch/brake pedal into
full “BRAKE” position.
• Move motion control lever to neutral (N) position.
IMPORTANT: THE MOTION CONTROL LEVER DOES
NOT RETURN TO NEUTRAL (N) POSITION WHEN THE
CLUTCH/BRAKE PEDAL IS DEPRESSED.
ENGINE • Move throttle control to slow position.
NOTE: Failure to move throttle control to slow position
and allowing engine to idle before stopping may cause
engine to “backfire”.
• Turn ignition key to “OFF” position and remove key.
Always remove key when leaving tractor to prevent
unauthorized use.
• Never use choke to stop engine.
12
The cutting height is controlled by turning the height adjustment knob in desired direction.
• Turn knob clockwise (
) to raise cutting height.
• Turn knob counterclockwise (
) to lower cutting
height.
The cutting height range is approximately 1-1/2" to 4". The
heights are measured from the ground to the blade tip with
the engine not running. These heights are approximate and
may vary depending upon soil conditions, height of grass
and types of grass being mowed.
• The average lawn should be cut to approximately 2-1/2
inches during the cool season and to over 3 inches
during hot months. For healthier and better looking
lawns, mow often and after moderate growth.
• For best cutting performance, grass over 6 inches in
height should be mowed twice. Make the first cut
relatively high; the second to desired height.
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
OPERATION
TO OPERATE ON HILLS
TO ADJUST GAUGE WHEELS (See Fig. 8)
Gauge wheels are properly adjusted when they are slightly
off the ground when mower is at the desired cutting height in
operating position. Gauge wheels then keep the deck in
proper position to help prevent scalping in most terrain
conditions.
NOTE:Adjust gauge wheels with tractor on a flat level
surface.
• Adjust mower to desired cutting height (See “TO ADJUST MOWER CUTTING HEIGHT” in the Operation
section of this manual).
• With mower in desired height of cut position, gauge
wheels should be assembled so they are slightly off the
ground. Install gauge wheel in appropriate hole with
shoulder bolt, 3/8 washer, and 3/8-16 locknut and tighten
securely.
• Repeat for opposite side installing gauge wheel in same
adjustment hole.
CAUTION: Do not drive up or down hills
with slopes greater than 15° and do not
drive across any slope.
•
•
•
•
•
Choose the slowest speed before starting up or down
hills.
Avoid stopping or changing speed on hills.
If slowing is necessary, move throttle control lever to
slower position.
If stopping is absolutely necessary, push clutch/brake
pedal quickly to brake position and engage parking
brake.
Move motion control lever to neutral (N) position.
IMPORTANT: THE MOTION CONTROL LEVER DOES
NOT RETURN TO NEUTRAL (N) POSITION WHEN THE
CLUTCH/BRAKE PEDAL IS DEPRESSED.
•
GUAGE WHEEL
MOUNTING
BRACKET
•
•
3/8-16
LOCKNUT
To restart movement, slowly release parking brake and
clutch/brake pedal.
Slowly move motion control lever to slowest setting.
Make all turns slowly.
TO TRANSPORT (See Figs. 6 and 10)
3/8 WASHER
SHOULDER
BOLT
GAUGE WHEEL
When pushing or towing your tractor, be sure to disengage
transmission by placing freewheel control in freewheeling
position. Free wheel control is located at the rear drawbar of
tractor.
• Raise attachment lift to highest position with attachment lift control.
• Pull freewheel control out and down into the slot and
release so it is held in the disengaged position.
• Do not push or tow tractor at more than two (2) MPH.
• To reengage transmission, reverse above procedure.
NOTE: To protect hood from damage when transporting
your tractor on a truck or a trailer, be sure hood is closed and
secured to tractor. Use an appropriate means of tying hood
to tractor (rope, cord, etc.).
FIG. 8
TO OPERATE MOWER (See Fig. 9)
Your tractor is equipped with an operator presence sensing
switch. Any attempt by the operator to leave the seat with
the engine running and the attachment clutch engaged will
shut off the engine.
• Select desired height of cut.
• Lower mower with attachment lift control.
• Start mower blades by engaging attachment clutch
control.
• TO STOP MOWER BLADES - disengage attachment
clutch control.
CAUTION: Do not operate the mower
without either the entire grass catcher,
on mowers so equipped, or the deflector
shield in place.
"ENGAGED" POSITION
ATTACHMENT
LIFT LEVER
HIGH POSITION
LOW
POSITION
ATTACHMENT
CLUTCH LEVER
"DISENGAGED"
POSITION
FIG. 10
TOWING CARTS AND OTHER ATTACHMENTS
DEFLECTOR
SHIELD
FIG. 9
Tow only the attachments that are recommended by and
comply with specifications of the manufacturer of your
tractor. Use common sense when towing. Too heavy of a
load, while on a slope, is dangerous. Tires can lose traction
with the ground and cause you to lose control of your tractor.
13
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
OPERATION
BEFORE STARTING THE ENGINE
TO START ENGINE (See Fig. 6)
When starting the engine for the first time or if the engine has
run out of fuel, it will take extra cranking time to move fuel
from the tank to the engine.
• Be sure freewheel control is in the transmission engaged
position.
• Sit on seat in operating position, depress clutch/brake
pedal and set parking brake.
• Place motion control lever in neutral (N) position.
• Move attachment clutch to “DISENGAGED” position.
• Move throttle control to fast position
• Pull choke control out for a cold engine start attempt. For
a warm engine start attempt the choke control may not
be needed.
NOTE: Before starting, read the warm and cold starting
procedures below.
• Insert key into ignition and turn key clockwise to
“START” position and release key as soon as engine
starts. Do not run starter continuously for more than
fifteen seconds per minute. If the engine does not start
after several attempts, push choke control in, wait a few
minutes and try again. If engine still does not start, pull
the choke control out and retry.
WARM WEATHER STARTING (50° F and above)
• When engine starts, slowly push choke control in until
the engine begins to run smoothly. If the engine starts
to run roughly, pull the choke control out slightly for a few
seconds and then continue to push the control in slowly.
• The attachments and ground drive can now be used. If
the engine does not accept the load, restart the engine
and allow it to warm up for one minute using the choke
as described above.
COLD WEATHER STARTING (50° F and below)
• When engine starts, slowly push choke control in until
the engine begins to run smoothly. Continue to push the
choke control in small steps allowing the engine to
accept small changes in speed and load, until the choke
control is fully in. If the engine starts to run roughly, pull
the choke control out slightly for a few seconds and then
continue to push the control in slowly. This may require
an engine warm-up period from several seconds to
several minutes, depending on the temperature.
AUTOMATIC TRANSMISSION WARM UP
• Before driving the unit in cold weather, the transmission
should be warmed up as follows:
• Be sure the tractor is on level ground.
• Place the motion control lever in neutral. Release
the parking brake and let the clutch/brake
slowly return to operating position.
• Allow one minute for transmission to warm up. This
can be done during the engine warm up period.
• The attachments can be used during the engine warmup period after the transmission has been warmed up
and may require the choke control be pulled out slightly.
NOTE: If at a high altitude (above 3000 feet) or in cold
temperatures (below 32 F) the carburetor fuel mixture may
need to be adjusted for best engine performance. See “TO
ADJUST CARBURETOR” in the Service and Adjustments
section of this manual.
CHECK ENGINE OIL LEVEL (See Fig. 15)
•
•
•
•
•
The engine in your tractor has been shipped, from the
factory, already filled with summer weight oil.
Check engine oil with tractor on level ground.
Remove oil fill cap/dipstick and wipe clean, reinsert the
dipstick and screw cap tight, wait for a few seconds,
remove and read oil level. If necessary, add oil until
“FULL” mark on dipstick is reached. Do not overfill.
For cold weather operation you should change oil for
easier starting (See “OIL VISCOSITY CHART” in the
Customer Responsibilities section of this manual).
To change engine oil, see the Customer Responsibilities
section in this manual.
ADD GASOLINE
•
Fill fuel tank. Use fresh, clean, regular unleaded
gasoline with a minimum of 87 octane. (Use of leaded
gasoline will increase carbon and lead oxide deposits
and reduce valve life). Do not mix oil with gasoline.
Purchase fuel in quantities that can be used within 30
days to assure fuel freshness.
IMPORTANT: WHEN OPERATING IN TEMPERATURES
BELOW 32°F(0°C), USE FRESH, CLEAN WINTER GRADE
GASOLINE TO HELP INSURE GOOD COLD WEATHER
STARTING.
WARNING: Experience indicates that alcohol blended fuels
(called gasohol or using ethanol or methanol) can attract
moisture which leads to separation and formation of acids
during storage. Acidic gas can damage the fuel system of
an engine while in storage. To avoid engine problems, the
fuel system should be emptied before storage of 30 days or
longer. Drain the gas tank, start the engine and let it run until
the fuel lines and carburetor are empty. Use fresh fuel next
season. See Storage Instructions for additional information.
Never use engine or carburetor cleaner products in the fuel
tank or permanent damage may occur.
CAUTION: Fill to bottom of gas tank
filler neck. Do not overfill. Wipe off any
spilled oil or fuel. Do not store, spill or
use gasoline near an open flame.
14
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
OPERATION
MOWING TIPS
PURGE TRANSMISSION
•
CAUTION: Never engage or disengage
freewheel lever while the engine is running.
•
To ensure proper operation and performance, it is recommended that the transmission be purged before operating
tractor for the first time. This procedure will remove any
trapped air inside the transmission which may have developed during shipping of your tractor.
•
•
IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE
REMOVAL FOR SERVICE OR REPLACEMENT, IT
SHOULD BE PURGED AFTER REINSTALLATION BEFORE
OPERATING THE TRACTOR.
•
•
Place tractor safely on level surface with engine off and
parking brake set.
• Disengage transmission by placing freewheel control in
freewheeling position (See “TO TRANSPORT” in this
section of manual).
• Sitting in the tractor seat, start engine. After the engine
is running, move throttle control to slow position. With
motion control lever in neutral (N) position, slowly
disengage clutch/brake pedal.
• Move motion control lever to full forward position and
hold for five (5) seconds. Move lever to full reverse
position and hold for five (5) seconds. Repeat this
procedure three (3) times.
NOTE: During this procedure there will be no movement of
drive wheels. The air is being removed from hydraulic drive
system.
• Move motion control lever to neutral (N) position. Shutoff engine and set parking brake.
• Engage transmission by placing freewheel control in
driving position (See “TO TRANSPORT” in this section
of manual).
• Sitting in the tractor seat, start engine. After the engine
is running, move throttle control to half (1/2) speed. With
motion control lever in neutral (N) position, slowly
disengage clutch/brake pedal.
• Slowly move motion control lever forward, after the
tractor moves approximately five (5) feet, slowly move
motion control lever to reverse position. After the tractor
moves approximately five (5) feet return the motion
control lever to the neutral (N) position. Repeat this
procedure with the motion control lever three (3) times.
• Your tractor is now purged and now ready for normal
operation.
•
•
•
•
Tire chains cannot be used when the mower housing is
attached to tractor.
Mower should be properly leveled for best mowing
performance. See “TO LEVEL MOWER HOUSING” in
the Service and Adjustments section of this manual.
The left hand side of mower should be used for trimming.
Drive so that clippings are discharged onto the area that
has been cut. Have the cut area to the right of the tractor.
This will result in a more even distribution of clippings
and more uniform cutting.
When mowing large areas, start by turning to the right so
that clippings will discharge away from shrubs, fences,
driveways, etc. After one or two rounds, mow in the
opposite direction making left hand turns until finished
(See Fig. 11 ).
If grass is extremely tall, it should be mowed twice to
reduce load and possible fire hazard from dried clippings. Make first cut relatively high; the second to the
desired height.
Do not mow grass when it is wet. Wet grass will plug
mower and leave undesirable clumps. Allow grass to dry
before mowing.
Always operate engine at full throttle when mowing
to assure better mowing performance and proper discharge of material. Regulate ground speed by selecting
a low enough gear to give the mower cutting performance as well as the quality of cut desired.
When operating attachments, select a ground speed
that will suit the terrain and give best performance of the
attachment being used.
FIG. 11
15
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
CUSTOMER RESPONSIBILITIES
MAINTENANCE SCHEDULE
FILL IN DATES
AS YOU COMPLETE
REGULAR SERVICE
E
S
S
GE
RS
US
RS
UR OUR
OU SON ORA
U
O
H
O
H
H
A
0
ST
E
8H
SE
25
50
10
RE
Y
Y
Y
Y
Y
RE
R
R
R
R
R
O
O
E
E
F
E
E
E
F
SERVICE
EV
EV
EV
EV
EV
BE
BE
H
AC
DATES
Check Brake Operation
Check Tire Pressure
T
R
A
C
T
0
R
Check Operator Presence and
Interlock Systems
Check for Loose Fasteners
7
Sharpen/Replace Mower Blades
4
Lubrication Chart
Check Battery Level
6
Clean Battery and Terminals
Check Transaxle Cooling
Adjust Blade Belt(s) Tension
5
Adjust Motion Drive Belt(s) Tension
5
Check Engine Oil Level
Change Engine Oil
E
N
G
I
N
E
1,2,3
Clean Air Filter
2
Clean Air Screen
2
Inspect Muffler/Spark Arrester
Replace Oil Filter (If equipped)
1, 2
Clean Engine Cooling Fins
2
Replace Spark Plug
Replace Air Filter Paper Cartridge
2
Replace Fuel Filter
1 - Change more often when operating under a heavy load or in high ambient temperatures.
2 - Service more often when operating in dirty or dusty conditions.
3 - If equipped with oil filter, change oil every 50 hours.
4 - Replace blades more often when mowing in sandy soil.
5 - If equipped with adjustable system.
6 - Not required if equipped with maintenance-free battery.
7 - Tighten front axle pivot bolt to 35 ft.-lbs. maximum.
Do not overtighten.
LUBRICATION CHART
ÀSPINDLE
GENERAL RECOMMENDATIONS
ZERK
The warranty on this tractor does not cover items that have
been subjected to operator abuse or negligence. To receive
full value from the warranty, operator must maintain tractor
as instructed in this manual.
Some adjustments will need to be made periodically to
properly maintain your tractor.
All adjustments in the Service and Adjustments section of
this manual should be checked at least once each season.
• Once a year you should replace the spark plug, clean or
replace air filter, and check blades and belts for wear. A
new spark plug and clean air filter assure proper air-fuel
mixture and help your engine run better and last longer.
ÀFRONT WHEEL
BEARING ZERK
ÀSPINDLE
ZERK
ÀFRONT WHEEL
BEARING ZERK
ÁENGINE
BEFORE EACH USE
•
•
•
•
•
Check engine oil level.
Check brake operation.
Check tire pressure.
Check operator presence and
interlock systems for proper operation.
Check for loose fasteners.
ÀGENERAL PURPOSE GREASE
ÁREFER TO CUSTOMER RESPONSIBILITIES “ENGINE”
SECTION
16
IMPORTANT: DO NOT OIL OR GREASE THE PIVOT POINTS
WHICH HAVE SPECIAL NYLON BEARINGS. VISCOUS LUBRICANTS WILL ATTRACT DUST AND DIRT THAT WILL SHORTEN
THE LIFE OF THE SELF-LUBRICATING BEARINGS. IF YOU
FEEL THEY MUST BE LUBRICATED, USE ONLY A DRY, POWDERED GRAPHITE TYPE LUBRICANT SPARINGLY.
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
CUSTOMER RESPONSIBILITIES
TRACTOR
TRAILING
EDGE UP
Always observe safety rules when performing any maintenance.
BLADE
MANDREL
ASSEMBLY
CENTER
HOLE
BRAKE OPERATION
If tractor requires more than six (6) feet stopping distance at
high speed in highest gear, then brake must be adjusted.
(See “TO ADJUST BRAKE” in the Service and Adjustments
section of this manual).
BLADE BOLT
(SPECIAL)
STAR
TIRES
•
Maintain proper air pressure in all tires (See “PRODUCT
SPECIFICATIONS” section of this manual).
• Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.
• Avoid stumps, stones, deep ruts, sharp objects and
other hazards that may cause tire damage.
NOTE: To seal tire punctures and prevent flat tires due to
slow leaks, tire sealant may be purchased from your local
parts dealer. Tire sealant also prevents tire dry rot and
corrosion.
FIG. 12
TO SHARPEN BLADE (See Fig. 13)
NOTE: We do not recommend sharpening blade - but if you
do, be sure the blade is balanced.
Care should be taken to keep the blade balanced. An
unbalanced blade will cause excessive vibration and eventual damage to mower and engine.
• The blade can be sharpened with a file or on a grinding
wheel. Do not attempt to sharpen while on the mower.
• To check blade balance, you will need a 5/8" diameter
steel bolt, pin, or a cone balancer. (When using a cone
balancer, follow the instructions supplied with balancer).
NOTE: Do not use a nail for balancing blade. The lobes of
the center hole may appear to be centered, but are not.
• Slide blade on to an unthreaded portion of the steel bolt
or pin and hold the bolt or pin parallel with the ground. If
blade is balanced, it should remain in a horizontal
position. If either end of the blade moves downward,
sharpen the heavy end until the blade is balanced.
OPERATOR PRESENCE SYSTEM
Be sure operator presence and interlock systems are working properly. If your tractor does not function as described,
repair the problem immediately.
• The engine should not start unless the brake pedal is
fully depressed and attachement clutch control is in the
disengaged position.
• When the engine is running, any attempt by the operator
to leave the seat without first setting the parking brake
should shut off the engine.
• When the engine is running and the attachment clutch is
engaged, any attempt by the operator to leave the seat
should shut off the engine.
• The attachment clutch should never operate unless the
operator is in the seat.
CENTER HOLE
BLADE
5/8" BOLT
OR PIN
BLADE CARE
For best results mower blades must be kept sharp. Replace
bent or damaged blades.
BLADE REMOVAL (See Fig. 12)
•
•
•
FIG. 13
Raise mower to highest position to allow access to
blades.
Remove hex bolt, lock washer and flat washer securing
blade.
Install new or resharpened blade with trailing edge up
towards deck as shown.
BATTERY
Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the
battery with an automotive charger will extend its life.
• Keep battery and terminals clean.
• Keep battery bolts tight.
• Keep small vent holes open.
• Recharge at 6-10 amperes for 1 hour.
NOTE: The original equipment battery on your tractor is
maintenance free. Do not attempt to open or remove caps or
covers. Adding or checking level of electrolyte is not
necessary.
IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER
HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL
ASSEMBLY.
•
•
Reassemble hex bolt, lock washer and flat washer in
exact order as shown.
Tighten bolt securely (27-35 Ft. Lbs. torque).
IMPORTANT: BLADE BOLT IS GRADE 8 HEAT TREATED.
17
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
CUSTOMER RESPONSIBILITIES
Change the oil after every 50 hours of operation or at least
once a year if the tractor is not used for 50 hours in one year.
Check the crankcase oil level before starting the engine and
after each eight (8) hours of operation. Tighten oil fill cap/
dipstick securely each time you check the oil level.
TO CLEAN BATTERY AND TERMINALS
Corrosion and dirt on the battery and terminals can cause the
battery to “leak” power.
• Remove terminal guard.
• Disconnect BLACK battery cable first then RED battery
cable and remove battery from tractor.
• Rinse the battery with plain water and dry.
• Clean terminals and battery cable ends with wire brush
until bright.
• Coat terminals with grease or petroleum jelly.
• Reinstall battery (See “REPLACING BATTERY” in the
SERVICE AND ADJUSTMENTS section of this manual).
TO CHANGE ENGINE OIL (See Figs. 14 and 15)
Determine temperature range expected before oil change.
All oil must meet API service classification SF-SJ.
• Be sure tractor is on level surface.
• Oil will drain more freely when warm.
• Catch oil in a suitable container.
• Remove oil fill cap/dipstick. Be careful not to allow dirt
to enter the engine when changing oil.
• Remove cap from bottom fitting of drain valve and install
the drain tube onto the fitting.
• Unlock drain valve by pushing inward and turning counterclockwise.
• To open, pull out on the drain valve.
• After oil has drained completely, close and lock the drain
valve by pushing inward and turning clockwise until the
pin is in the locked position as shown.
• Remove the drain tube and replace the cap onto to the
bottom fitting of the drain valve.
• Refill engine with oil through oil fill dipstick tube. Pour
slowly. Do not overfill. For approximate capacity see
“PRODUCT SPECIFICATIONS” section of this manual.
• Use gauge on oil fill cap/dipstick for checking level. Be
sure dipstick cap is tightened securely for accurate
reading. Keep oil at “FULL” line on dipstick.
V-BELTS
Check V-belts for deterioration and wear after 100 hours of
operation and replace if necessary. The belts are not
adjustable. Replace belts if they begin to slip from wear.
TRANSAXLE COOLING
The transmission fan and cooling fins should be kept clean
to assure proper cooling.
Do not attempt to clean fan or transmission while engine is
running or while the transmission is hot. To prevent possible
damage to seals, do not use high pressure water or steam
to clean transaxle.
• Inspect cooling fan to be sure fan blades are intact and
clean.
• Inspect cooling fins for dirt, grass clippings and other
materials. To prevent damage to seals, do not use
compressed air or high pressure sprayer to clean cooling
fins.
OIL DRAIN VALVE
CLOSED
AND
LOCKED
POSITION
TRANSAXLE PUMP FLUID
The transaxle was sealed at the factory and fluid maintenance is not required for the life of the transaxle. Should the
transaxle ever leak or require servicing, contact your nearest
authorized service center/department.
ENGINE
LUBRICATION
Only use high quality detergent oil rated with API service
classification SF-SJ. Select the oil’s SAE viscosity grade
according to your expected operating temperature.
FIG. 15
CLEAN AIR SCREEN
SAE VISCOSITY GRADES
Air screen must be kept free of dirt and chaff to prevent
engine damage from overheating. Clean with a wire brush or
compressed air to remove dirt and stubborn dried gum fibers.
SAE 30
5W-30
-20
F
C
-30
0
-20
30
-10
DRAIN
TUBE
CAP
32
40
0
60
10
20
ENGINE COOLING FINS
100
80
30
Remove any dust, dirt or oil from engine cooling fins to
prevent engine damage from overheating. Air guide covers
must be removed. Remove side panels and hood (See “TO
REMOVE HOOD AND GRILL ASSEMBLY” in the Service
and Adjustments section of this manual).
40
TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE
FIG. 14
NOTE: Although multi-viscosity oils (5W30, 10W30 etc.)
improve starting in cold weather, these multi-viscosity oils
will result in increased oil consumption when used above
32°F. Check your engine oil level more frequently to avoid
possible engine damage from running low on oil.
18
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
CUSTOMER RESPONSIBILITIES
AIR FILTER
CLAMP
CLAMP
Your engine will not run properly using a dirty air filter. Clean
the foam pre-cleaner after every 25 hours of operation or
every season. Service paper cartridge every 100 hours of
operation or every season, whichever occurs first.
Service air cleaner more often under dusty conditions.
(See engine manual for instructions).
FUEL
FILTER
FIG. 16
MUFFLER
CLEANING
Inspect and replace corroded muffler and spark arrester (if
equipped) as it could create a fire hazard and/or damage.
•
Clean engine, battery, seat, finish, etc. of all foreign
matter.
• Keep finished surfaces and wheels free of all gasoline,
oil, etc.
• Protect painted surfaces with automotive type wax.
We do not recommend using a garden hose to clean your
tractor unless the electrical system, muffler, air filter and
carburetor are covered to keep water out. Water in engine
can result in a shortened engine life.
SPARK PLUGS
Replace spark plugs at the beginning of each mowing
season or after every 100 hours of operation, whichever
occurs first. Spark plug type and gap setting are shown in
“PRODUCT SPECIFICATIONS” section of this manual.
IN-LINE FUEL FILTER (See Fig. 16)
The fuel filter should be replaced once each season. If fuel
filter becomes clogged, obstructing fuel flow to carburetor,
replacement is required.
• With engine cool, remove filter and plug fuel line sections.
• Place new fuel filter in position in fuel line with arrow
pointing towards carburetor.
• Be sure there are no fuel line leaks and clamps are
properly positioned.
• Immediately wipe up any spilled gasoline.
19
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
SERVICE AND ADJUSTMENTS
CAUTION: BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:
• Depress clutch/brake pedal fully and set parking brake.
• Place motion control lever in neutral (N) position.
• Place attachment clutch in “DISENGAGED” position.
• Turn ignition key “OFF” and remove key.
• Make sure the blades and all moving parts have completely stopped.
• Disconnect spark plug wire from spark plug and place wire where it cannot come in contact
with plug.
TRACTOR
IMPORTANT: IF AN ATTACHMENT OTHER THAN THE
MOWER DECK IS TO BE MOUNTED ON THE TRACTOR, REMOVE THE FRONT LINKS AND HOOK THE
CLUTCH SPRING INTO SQUARE HOLE IN FRAME.
TO REMOVE MOWER (See Fig. 17)
Mower will be easier to remove from the right side of tractor.
• Place attachment clutch in “DISENGAGED” position.
• Move attachment lift lever forward to lower mower to its
lowest position.
• Roll belt off engine pulley.
• Remove small retainer spring, and lift clutch spring off
pulley bolt.
• Remove large retainer spring, slide collar off and push
housing guide out of bracket.
• Disconnect anti-swaybar from chassis bracket by removing retainer spring.
• Disconnect suspension arms from rear deck brackets
by removing retainer springs.
• Disconnect front links from deck by removing retainer
springs.
• Raise lift lever to raise suspension arms. Slide mower
out from under tractor.
COLLAR
LARGE
RETAINER
SPRING
TO INSTALL MOWER
Follow procedure described in “INSTALL MOWER AND
DRIVE BELT” in the Assembly section of this manual.
TO LEVEL MOWER HOUSING
Adjust the mower while tractor is parked on level ground or
driveway. Make sure tires are properly inflated (See “PRODUCT SPECIFICATIONS” section of this manual). If tires are
over or underinflated, you will not properly adjust your
mower.
SMALL
RETAINER
SPRING
CLUTCH SPRING
SUSPENSION ARMS
SQUARE HOLE
ENGINE PULLEY
HOUSING
GUIDE
FRONT LINK
RETAINER SPRINGS
(BOTH SIDES)
ANTI-SWAY BAR
RETAINER SPRING
FIG. 17
20
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
SERVICE AND ADJUSTMENTS
SIDE-TO-SIDE ADJUSTMENT (See Figs. 18 and 19)
• Raise mower to its highest position.
• At the midpoint of both sides of mower, measure height
from bottom edge of mower to ground. Distance “A” on
both sides of mower should be the same or within 1/4"
of each other.
• If adjustment is necessary, make adjustment on one
side of mower only.
• To raise one side of mower, tighten lift link adjustment
nut on that side.
• To lower one side of mower, loosen lift link adjustment
nut on that side.
NOTE: Three full turns of adjustment nut will change mower
height about 1/8".
• Recheck measurements after adjusting.
MANDREL
"D"
"D"
FIG. 20
BOTH FRONT LINKS MUST BE EQUAL IN LENGTH
BOTTOM EDGE
OF MOWER
TO GROUND
BOTTOM EDGE
OF MOWER
TO GROUND
NUT "E"
“A”
“A”
GROUND LINE
NUT "F"
TRUNNION
FIG. 18
SUSPENSION ARM
FRONT LINKS
FIG. 21
LIFT LINK ADJUSTMENT NUT
TO REPLACE MOWER DRIVE BELT
FIG. 19
MOWER DRIVE BELT REMOVAL (See Fig. 22) • Park tractor on a level surface. Engage parking brake.
Disengage attachment clutch control.
• Remove screws from L.H. mandrel cover and remove
cover.
• Remove small retainer spring and lift clutch spring off
pulley bolt.
• Roll belt over the top of L.H. mandrel pulley.
• Remove belt from engine pulley.
• Remove belt from idler pulleys.
• Remove any dirt or grass clippings which may have
accumulated around mandrels and entire upper deck
surface.
• Check primary idler arm and two idlers to see that they
rotate freely.
FRONT-TO-BACK ADJUSTMENT (See Figs. 20 and 21)
IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF
THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS
NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS
EQUALLY SO MOWER WILL STAY LEVEL SIDE-TOSIDE.
To obtain the best cutting results, the mower housing should
be adjusted so that the front is approximately 1/8" to 1/2"
lower than the rear when the mower is in its highest position.
Check adjustment on right side of tractor. Measure distance
“D” directly in front and behind the mandrel at bottom edge
of mower housing as shown.
• Before making any necessary adjustments, check that
both front links are equal in length.
• If links are not equal in length, adjust one link to same
length as other link.
• To lower front of mower loosen nut “E” on both front links
an equal number of turns.
• When distance “D” is 1/8" to 1/2" lower at front than rear,
tighten nuts “F” against trunnion on both front links.
• To raise front of mower, loosen nut “F” from trunnion on
both front links. Tighten nut “E” on both front links an
equal number of turns.
• When distance “D” is 1/8" to 1/2" lower at front than rear,
tighten nut “F” against trunnion on both front links.
• Recheck side-to-side adjustment.
MOWER DRIVE BELT INSTALLATION (See Fig. 22) • Install belt in both idlers. Make sure belt is in both belt
keepers at the idlers as shown.
• Install new belt onto engine pulley.
• Roll belt into upper groove of L.H. mandrel pulley.
• Carefully check belt routing making sure belt is in the
grooves correctly and inside belt keepers.
• Reassemble clutch spring to pulley bolt.
• Reassemble L.H. mandrel cover.
21
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
SERVICE AND ADJUSTMENTS
CLUTCH SPRING
SCREWS
L.H.
MANDREL
COVER
TO ADJUST BRAKE (See Fig. 24)
SMALL
RETAINER
SPRING
IDLER
PULLEYS
Your tractor is equipped with an adjustable brake system
which is mounted on the side of the transaxle.
If tractor requires more than six (6) feet stopping distance at
high speed in highest gear on a level dry concrete or paved
surface, then brake must be adjusted.
• Depress clutch/brake pedal and engage parking brake.
• Measure distance between brake operating arm and nut
“A” on brake rod.
• If distance is other than 1-1/2", loosen jam nut and turn
nut “A” until distance becomes 1-1/2". Retighten jam nut
against nut “A”.
• Road test tractor for proper stopping distance as stated
above. Readjust if necessary. If stopping distance is
still greater than six (6) feet in highest gear, further
maintenance is necessary. Contact your nearest authorized service center/department.
ENGINE
PULLEY
L.H.
MANDREL
MOWER
DRIVE
BELT
BELT
KEEPERS
WITH PARKING
BRAKE “ENGAGED”
1-1/2"
JAM NUT
FIG. 22
TO REPLACE MOWER BLADE DRIVE BELT
(See Fig. 23)
DO NOT TOUCH THIS
NUT. IF FURTHER
BRAKE ADJUSTMENT IS
NECESSARY CONTACT
YOUR NEAREST
AUTHORIZED SERVICE
CENTER/DEPARTMENT
Park the tractor on level surface. Engage parking brake.
• Remove mower drive belt (See “TO REPLACE MOWER
DRIVE BELT” in this section of this manual).
• Remove mower (See “TO REMOVE MOWER” in this
section of this manual).
• Remove screws from R.H. mandrel cover and remove
cover.
• Carefully roll belt off R.H. mandrel pulley.
• Remove belt from center mandrel pulley, idler pulley,
and L.H. mandrel pulley.
• Remove any dirt or grass which may have accumulated
around mandrels and entire upper deck surface.
• Check secondary idler arm and idler to see that they
rotate freely.
• Install new belt in lower groove of L.H. mandrel pulley,
idler pulley, and center mandrel pulley as shown.
• Roll belt over R.H. mandrel pulley. Make sure belt is in
all grooves properly.
• Reinstall R.H. mandrel cover.
• Reinstall mower to tractor (See “INSTALL MOWER AND
DRIVE BELT” in the Assembly section of this manual).
• Reassemble mower drive belt (See “TO REPLACE
MOWER DRIVE BELT” in this section of this manual).
L.H. MANDREL
CENTER
MANDREL
OPERATING
ARM
FIG. 24
TO REPLACE MOTION DRIVE BELT
(See Fig. 25)
Park the tractor on level surface. Engage parking brake. For
assistance, there is a belt installation guide decal on bottom
side of left footrest.
• Remove mower (See “TO REMOVE MOWER” in this
section of this manual.)
• Remove belt from stationary idler and clutching idler.
• Pull belt slack toward rear of tractor. Carefully remove
belt upwards from transmission input pulley and over
cooling fan blades.
• Pull belt toward front of tractor and remove downward
from around engine pulley.
• Install new belt by reversing above procedure.
ENGINE
PULLEY
SECONDARY
IDLER ARM
CLUTCHING
IDLER
SPRING
R.H.
MANDREL
COVER
MOWER
BLADE
DRIVE BELT
NUT “A”
STATIONARY
IDLER
TRANSMISSION
INPUT PULLEY
SWAY BAR
BRACKET
IDLER PULLEY
SCREW
FIG. 23
22
www.mymowerparts.com
FIG. 25
For Parts Call K&T 606-678-9623 or 606-561-4983
SERVICE AND ADJUSTMENTS
•
On rear wheels only: align grooves in rear wheel hub and
axle. Insert square key.
• Replace washers and snap retaining ring securely in
axle groove.
• Replace axle cover.
NOTE: To seal tire punctures and prevent flat tires due to
slow leaks, tire sealant may be purchased from your local
parts dealer. Tire sealant also prevents tire dry rot and
corrosion.
TRANSAXLE MOTION CONTROL LEVER
NEUTRAL ADJUSTMENT(See Fig. 26)
The motion control lever has been preset at the factory and
adjustment should not be necessary.
• Loosen adjustment bolt in front of the right rear wheel,
and lightly tighten.
• Start engine and move motion control lever until tractor
does not move forward or backward.
• Hold motion control lever in that position and turn engine
off.
• While holding motion control lever in place, loosen the
adjustment bolt.
• Move motion control lever to the neutral (N) (lock gate)
position.
• Tighten adjustment bolt securely.
NOTE: If additional clearance is needed to get to adjustment
bolt, move mower deck height to the lowest position.
After above adjustment is made, if the tractor still creeps
forward or backward while motion control lever is in neutral
position, follow these steps:
• Loosen the adjustment bolt.
• Move the motion control lever 1/4 to 1/2 inch in the
direction it is trying to creep.
• Tighten adjustment bolt securely.
• Start engine and test.
• If tractor still creeps, repeat above steps until satisfied.
MOTION CONTROL
LEVER
WASHERS
RETAINING
RING
AXLE COVER
SQUARE KEY
(REAR WHEEL ONLY)
FIG. 27
TO START ENGINE WITH A WEAK BATTERY
(See Fig. 28)
CAUTION: Lead-acid batteries generate
explosive gases. Keep sparks, flame
and smoking materials away from batteries. Always wear eye protection when
around batteries.
If your battery is too weak to start the engine, it should be
recharged. (See “BATTERY” in the Customer Responsibilities section of this manual).
If “jumper cables” are used for emergency starting, follow
this procedure:
NEUTRAL
LOCK GATE
IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12
VOLT NEGATIVE GROUNDED SYSTEM. THE OTHER
VEHICLE MUST ALSO BE A 12 VOLT NEGATIVE
GROUNDED SYSTEM. DO NOT USE YOUR TRACTOR
BATTERY TO START OTHER VEHICLES.
ADJUSTMENT
BOLT
TO ATTACH JUMPER CABLES • Connect each end of the RED cable to the POSITIVE (+)
terminal of each battery, taking care not to short against
chassis.
• Connect one end of the BLACK cable to the NEGATIVE
(-) terminal of fully charged battery.
• Connect the other end of the BLACK cable to good
CHASSIS GROUND, away from fuel tank and battery.
TO REMOVE CABLES, REVERSE ORDER • BLACK cable first from chassis and then from the fully
charged battery.
• RED cable last from both batteries.
FIG. 26
TRANSMISSION REMOVAL/REPLACEMENT
Should your transmission require removal for service or
replacement, it should be purged after reinstallation and
before operating the tractor. See “PURGE TRANSMISSION” in the Operation section of this manual.
TO ADJUST STEERING WHEEL ALIGNMENT
If steering wheel crossbars are not horizontal (left to right)
when wheels are positioned straight forward, remove steering wheel and reassemble per instructions in the Assembly
section of this manual.
FRONT WHEEL TOE-IN/CAMBER
The front wheel toe-in and camber are not adjustable on your
tractor. If damage has occurred to affect the front wheel toein or camber, contact your nearest authorized service
center/department.
“POSITIVE” (+)
TO REMOVE WHEEL FOR REPAIRS
(See Fig. 27)
•
•
•
Block up axle securely.
Remove axle cover, retaining ring and washers to allow
wheel removal (rear wheel contains a square key - Do not
lose).
Repair tire and reassemble.
“NEGATIVE” (-)
L.H. PANEL
BOLT
23
www.mymowerparts.com
FIG. 28
For Parts Call K&T 606-678-9623 or 606-561-4983
SERVICE AND ADJUSTMENTS
REPLACING BATTERY (See Fig. 29)
TO REMOVE HOOD AND GRILL ASSEMBLY
(See Fig. 30)
CAUTION: Do not short battery terminals by allowing a wrench or any other
object to contact both terminals at the
same time. Before connecting battery,
remove metal bracelets, wristwatch
bands, rings, etc.
Positive terminal must be connected
first to prevent sparking from accidental
grounding.
•
•
•
•
•
•
•
•
•
•
•
•
•
HOOD
Lift hood to raised position.
Remove terminal guard.
Disconnect BLACK battery cable then RED battery
cable and carefully remove battery from tractor.
Install new battery with terminals in same position as old
battery.
Reinstall terminal guard.
First connect RED battery cable to positive (+) battery
terminal with hex bolt and keps nut as shown. Tighten
securely.
Connect BLACK grounding cable to negative (-) battery
terminal with remaining hex bolt and keps nut. Tighten
securely
Close terminal access doors.
Close hood.
HEADLIGHT
WIRE
CONNECTOR
FIG. 30
ENGINE
Maintenance, repair, or replacement of the emission control
devices and systems, which are being done at the customers expense, may be performed by any non-road engine
repair establishment or individual. Warranty repairs must be
performed by an authorized engine manufacturer's service
outlet.
KEPS NUT
TERMINAL
ACCESS
DOOR
Raise hood.
Unsnap headlight wire connector.
Stand in front of tractor. Grasp hood at sides, tilt toward
engine and lift off of tractor.
To replace, reverse above procedure.
HEX BOLT
POSITIVE
(RED) CABLE
TO ADJUST THROTTLE CONTROL CABLE
TERMINAL
GUARD
NEGATIVE
(BLACK) CABLE
The throttle control has been preset at the factory and
adjustment should not be necessary. Check adjustment as
described below before loosening cable. If adjustment is
necessary, see engine manual.
FIG. 29
TO REPLACE HEADLIGHT BULB
TO ADJUST CHOKE CONTROL
•
•
•
The choke control has been preset at the factory and
adjustment should not be necessary. Check adjustment as
described below before loosening cable. If adjustment is
necessary, see engine manual.
•
Raise hood.
Pull bulb holder out of the hole in the backside of the grill.
Replace bulb in holder and push bulb holder securely
back into the hole in the backside of the grill.
Close hood.
TO ADJUST CARBURETOR
INTERLOCKS AND RELAYS
The carburetor has been preset at the factory and adjustment should not be necessary. However, minor adjustment
may be required to compensate for differences in fuel,
temperature, altitude or load. If the carburetor does need
adjustment, see engine manual.
Loose or damaged wiring may cause your tractor to run
poorly, stop running, or prevent it from starting.
• Check wiring. See electrical wiring diagram in the Repair
Parts section.
IMPORTANT: NEVER TAMPER WITH THE ENGINE
GOVERNOR, WHICH IS FACTORY SET FOR PROPER
ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE
THE FACTORY HIGH SPEED SETTING CAN BE
DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED
HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR
NEAREST
AUTHORIZED
SERVICE
CENTER/
DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND
EXPERIENCE
TO
MAKE
ANY
NECESSARY
ADJUSTMENTS.
TO REPLACE FUSE
Replace with 20 amp automotive-type plug-in fuse. The fuse
holder is located behind the dash.
24
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
STORAGE
Immediately prepare your tractor for storage at the end of the
season or if the tractor will not be used for 30 days or more.
ENGINE
FUEL SYSTEM
CAUTION: Never store the tractor with
gasoline in the tank inside a building
where fumes may reach an open flame
or spark. Allow the engine to cool
before storing in any enclosure.
IMPORTANT: IT IS IMPORTANT TO PREVENT GUM
DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM
PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL
HOSE, OR TANK DURING STORAGE.
ALSO,
EXPERIENCE INDICATES THAT ALCOHOL BLENDED
FUELS (CALLED GASOHOL OR USING ETHANOL OR
METHANOL) CAN ATTRACT MOISTURE WHICH LEADS
TO SEPARATION AND FORMATION OF ACIDS DURING
STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL
SYSTEM OF AN ENGINE WHILE IN STORAGE.
TRACTOR
Remove mower from tractor for winter storage. When mower
is to be stored for a period of time, clean it thoroughly,
remove all dirt, grease, leaves, etc. Store in a clean, dry
area.
• Clean entire tractor (See “CLEANING” in the Customer
Responsibilities section of this manual).
• Inspect and replace belts, if necessary (See belt replacement instructions in the Service and Adjustments
section of this manual).
• Lubricate as shown in the Customer Responsibilities
section of this manual.
• Be sure that all nuts, bolts and screws are securely
fastened. Inspect moving parts for damage, breakage
and wear. Replace if necessary.
• Touch up all rusted or chipped paint surfaces; sand
lightly before painting.
•
•
Drain the fuel tank.
Start the engine and let it run until the fuel lines and
carburetor are empty.
• Never use engine or carburetor cleaner products in the
fuel tank or permanent damage may occur.
• Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable alternative in
minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage
container. Always follow the mix ratio found on stabilizer
container. Run engine at least 10 minutes after adding
stabilizer to allow the stabilizer to reach the carburetor. Do
not drain the gas tank and carburetor if using fuel stabilizer.
ENGINE OIL
Drain oil (with engine warm) and replace with clean engine oil.
(See “ENGINE” in the Customer Responsibilities section of
this manual).
BATTERY
•
•
•
•
•
Fully charge the battery for storage.
After a period of time in storage, battery may require
recharging.
To help prevent corrosion and power leakage during long
periods of storage, battery cables should be disconnected and battery cleaned thoroughly (see “TO CLEAN
BATTERY AND TERMINALS” in the Customer Responsibilities section of this manual).
After cleaning, leave cables disconnected and place
cables where they cannot come in contact with battery
terminals.
If battery is removed from tractor for storage, do not
store battery directly on concrete or damp surfaces.
CYLINDER(S)
•
•
•
•
Remove spark plug(s).
Pour one ounce of oil through spark plug hole(s) into
cylinder(s).
Turn ignition key to “START” position for a few seconds
to distribute oil.
Replace with new spark plug(s).
OTHER
•
•
•
•
Do not store gasoline from one season to another.
Replace your gasoline can if your can starts to rust.
Rust and/or dirt in your gasoline will cause problems.
If possible, store your tractor indoors and cover it to give
protection from dust and dirt.
Cover your tractor with a suitable protective cover that
does not retain moisture. Do not use plastic. Plastic
cannot breathe which allows condensation to form and
will cause your tractor to rust.
IMPORTANT: NEVER COVER TRACTOR WHILE ENGINE
AND EXHAUST AREAS ARE STILL WARM.
25
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
TROUBLESHOOTING POINTS
PROBLEM
CAUSE
Will not start
1.
2.
3.
4.
5.
6.
7.
Out of fuel.
Engine not “CHOKED” properly.
Engine flooded.
Bad spark plug.
Dirty air filter.
Dirty fuel filter.
Water in fuel.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Loose or damaged wiring.
Carburetor out of adjustment.
8.
9.
10.
Hard to start
CORRECTION
Engine valves out of adjustment.
10.
Fill fuel tank.
See “TO START ENGINE” in Operation section.
Wait several minutes before attempting to start.
Replace spark plug.
Clean/replace air filter.
Replace fuel filter.
Drain fuel tank and carburetor, refill tank with fresh
gasoline and replace fuel filter.
Check all wiring.
See “To Adjust Carburetor” in Service Adjustments
section.
Contact an authorized service center/department.
1.
2.
3.
4.
5.
6.
7.
Dirty air filter.
Bad spark plug.
Weak or dead battery.
Dirty fuel filter.
Stale or dirty fuel.
Loose or damaged wiring.
Carburetor out of adjustment.
1.
2.
3.
4.
5.
6.
7.
8.
Engine valves out of adjustment.
8.
Clean/replace air filter.
Replace spark plug.
Recharge or replace battery.
Replace fuel filter.
Drain fuel tank and refill with fresh gasoline.
Check all wiring.
See “To Adjust Carburetor” in Service Adjustments
section.
Contact an authorized service center/department.
Engine will not turn over
1.
2.
3.
4.
5.
6.
7.
8.
9.
Brake pedal not depressed.
Attachment clutch is engaged.
Weak or dead battery.
Blown fuse.
Corroded battery terminals.
Loose or damaged wiring.
Faulty ignition switch.
Faulty solenoid or starter.
Faulty operator presence switch(es).
1.
2.
3.
4.
5.
6.
7.
8.
9.
Depress brake pedal.
Disengage attachment clutch.
Recharge or replace battery.
Replace fuse.
Clean battery terminals.
Check all wiring.
Check/replace ignition switch.
Check/replace solenoid or starter.
Contact an authorized service center/department.
Engine clicks but will not
start
1.
2.
3.
4.
Weak or dead battery.
Corroded battery terminals.
Loose or damaged wiring.
Faulty solenoid or starter.
1.
2.
3.
4.
Recharge or replace battery.
Clean battery terminals.
Check all wiring.
Check/replace solenoid or starter.
Loss of power
1.
2.
3.
4.
5.
6.
7.
8.
9.
Cutting too much grass/too fast.
Throttle in “CHOKE” position.
Build-up of grass, leaves and trash under mower.
Dirty air filter.
Low oil level/dirty oil.
Faulty spark plug.
Dirty fuel filter.
Stale or dirty fuel.
Water in fuel.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Set in “Higher Cut” position/reduce speed.
Adjust throttle control.
Clean underside of mower housing.
Clean/replace air filter.
Check oil level/change oil.
Clean and regap or change spark plug.
Replace fuel filter.
Drain fuel tank and refill with fresh gasoline.
Drain fuel tank and carburetor, refill tank with fresh
gasoline and replace fuel filter.
Connect and tighten spark plug wire.
Clean engine air screen/fins.
Clean/replace muffler.
Check all wiring.
See “To Adjust Carburetor” in Service Adjustments
section.
Contact an authorized service center/department.
Excessive vibration
10.
11.
12.
13.
14.
Spark plug wire loose.
Dirty engine air screen/fins.
Dirty/clogged muffler.
Loose or damaged wiring.
Carburetor out of adjustment.
10.
11.
12.
13.
14.
15.
Engine valves out of adjustment.
15.
1.
2.
3.
Worn, bent or loose blade.
Bent blade mandrel.
Loose/damaged part(s).
1.
2.
3.
Replace blade. Tighten blade bolt.
Replace blade mandrel.
Tighten loose part(s). Replace damaged parts.
26
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
TROUBLESHOOTING POINTS
PROBLEM
CAUSE
CORRECTION
Engine continues to run
when operator leaves
seat with attachment
clutch engaged
1.
Faulty operator-safety presence control system.
1.
Check wiring, switches and connections. If not
corrected, contact an authorized service center/
department.
Poor cut - uneven
1.
2.
3.
4.
5.
Worn, bent or loose blade.
Mower deck not level.
Buildup of grass, leaves, and trash under mower.
Bent blade mandrel.
Clogged mower deck vent holes from buildup of
grass, leaves, and trash around mandrels.
1.
2.
3.
4.
5.
Replace blade. Tighten blade bolt.
Level mower deck.
Clean underside of mower housing.
Replace blade mandrel.
Clean around mandrels to open vent holes.
Mower blades will not
rotate
1.
2.
3.
4.
Obstruction in clutch mechanism.
Worn/damaged mower drive belt.
Frozen idler pulley.
Frozen blade mandrel.
1.
2.
3.
4.
Remove obstruction.
Replace mower drive belt.
Replace idler pulley.
Replace blade mandrel.
Poor grass discharge
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Engine speed too slow.
Travel speed too fast.
Wet grass.
Mower deck not level.
Low/uneven tire air pressure.
Worn, bent or loose blade.
Buildup of grass, leaves and trash under mower.
Mower drive belt worn.
Blades improperly installed.
Improper blades used.
Clogged mower deck vent holes from buildup of
grass, leaves, and trash around mandrels.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Place throttle control in “FAST” position.
Shift to slower speed.
Allow grass to dry before mowing.
Level mower deck.
Check tires for proper air pressure.
Replace/sharpen blade. Tighten blade bolt.
Clean underside of mower housing.
Replace mower drive belt.
Reinstall blades sharp edge down.
Replace with blades listed in this manual.
Clean around mandrels to open vent holes.
Headlight(s) not working
(if so equipped)
1.
2.
3.
4.
5.
Switch is “OFF”.
Bulb(s) or lamp(s) burned out.
Faulty light switch.
Loose or damaged wiring.
Blown fuse.
1.
2.
3.
4.
5.
Turn switch “ON”.
Replace bulb(s) or lamp(s).
Check/replace light switch.
Check wiring and connections.
Replace fuse.
Battery will not charge
1.
2.
3.
4.
Bad battery cell(s).
Poor cable connections.
Faulty regulator (if so equipped).
Faulty alternator.
1.
2.
3.
4.
Replace battery.
Check/clean all connections.
Replace regulator.
Replace alternator.
Loss of drive
1.
2.
3.
Freewheel control in “disengaged” position.
Motion drive belt worn, damaged, or broken.
Air trapped in transmission during shipment
or servicing.
1.
2.
3.
Place freewheel control in “engaged” position.
Replace motion drive belt.
Purge transmission.
Engine “backfires”
when turning engine
“OFF”
1.
Engine throttle control not set at “SLOW”
position for 30 seconds before stopping engine.
1.
Move throttle control to “SLOW” position and allow
to idle for 30 seconds before stopping engine.
27
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
SERVICE NOTES
28
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
TRACTOR - - MODEL NUMBER SGT18H46C
SCHEMATIC
RED
BLACK
BATTERY
RED
A
RED
FUSE
AMMETER
(OPTIONAL)
M
STARTER
BLACK
WHITE
SOLENOID
RED
B
S
G
BLACK
L
M
CLUTCH / BRAKE
(PEDAL UP)
A1
A2
WHITE
SEAT SWITCH
(NOT OCCUPIED)
IGNITION
SWITCH
WHITE
BLACK
BLACK
BLACK
BLACK
HOUR
METER
ATT'MENT CLUTCH
(CLUTCH OFF)
GROUNDING
CONNECTOR
(OPTIONAL)
BLUE
SPARK
PLUG
GAP
(2 PLUGS ON
TWIN CYL. ENGINES)
IGNITION
UNIT
BLACK
FUEL
LINE
CHARGING SYSTEM OUTPUT
3 AMP DC @ 3600 RPM
FUEL SHUT-OFF SOLENOID
(IF SO EQUIPPED)
28 VOLTS AC MIN. @ 3600 RPM
(CHARGING SYSTEM DISCONNECTED)
RED
LIGHTING SYSTEM OUTPUT
5 AMP AC @ 3600 RPM
ORANGE
BLACK
DIODE
ALTERNATOR
14 VOLTS AC MIN. @ 3600 RPM (LIGHTS OFF)
NOTE
YOUR TRACTOR IS
EQUIPPED WITH A SPECIAL
ALTERNATOR SYSTEM.
THE LIGHTS ARE NOT
CONNECTED TO THE
BATTERY, BUT HAVE THEIR
OWN ELECTRICAL SOURCE.
BECAUSE OF THIS, THE
BRIGHTNESS OF THE LIGHTS
WILL CHANGE WITH ENGINE
SPEED. AT IDLE THE LIGHTS
WILL DIM. AS THE ENGINE IS
SPEEDED UP, THE LIGHTS
WILL BECOME THEIR BRIGHTEST.
BLACK
BROWN
HEADLIGHTS
NON-REMOVABLE
CONNECTIONS
IGNITION SWITCH
POSITION
CIRCUIT
OFF
M+G+A1
RUN/LIGHT
B+A1
RUN
START
B+A1
B + S + A1
REMOVABLE
CONNECTIONS
“MAKE”
NONE
A2+L
NONE
NONE
WIRING INSULATED CLIPS
NOTE: IF WIRING INSULATED CLIPS WERE REMOVED FOR
SERVICING OF UNIT, THEY SHOULD BE REPLACED TO
PROPERLY SECURE YOUR WIRING.
29
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
REPAIR PARTS
TRACTOR - - MODEL NUMBER SGT18H46C
ELECTRICAL
21
22
42
24
41
43
27
27
40
26
27
27
25
16
16
33
30
10
D.C
11
.A
MPE
RES
29
45
28
27
55
12
2
1
8
12
30
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
REPAIR PARTS
TRACTOR - - MODEL NUMBER SGT18H46C
ELECTRICAL
KEY
NO.
PART
NO.
DESCRIPTION
1
2
8
10
11
12
16
21
22
24
25
26
27
28
29
30
33
40
41
42
43
45
55
163465
74760412
7603J
145211
150109
145769
153664
166181
4152J
108423X
146148
175158
73510400
145491
121305X
175566
140401
178446
71110408
131563
178861
121433X
17490508
Battery, 12 Volt, 28 Amp
Bolt, Hex Head 1/4-20 UNC x 3/4
Tray, Battery
Bolt, Battery Front 1/4-20 x 7.5 Zinc
Holddown Battery Dash Mount
Nut, Push Nylon 1/4" Battery Front
Switch Interlock Push-In
Harness, Light
Bulb, Light
Cable, Battery, 6 Gauge, 16", Red
Cable, Battery
Fuse, 20 Amp
Nut, Hex, Keps 1/4-20 UNC
Cable, Ground, 6 Gauge, 12", Black
Switch, Plunger
Switch, Ignition, Push-In
Key, Ignition
Harness, Ignition
Bolt, Hex, Fin. 1/4-20 x 1/2
Cover, Terminal, Red
Solenoid
Ammeter, Rectangular
Screw, Thdrol 5/16-18 x 1/2 TYT
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
31
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
REPAIR PARTS
TRACTOR - - MODEL NUMBER SGT18H46C
CHASSIS
119
30
24
29
36
87
17
212
36
36
24
26
25
26
25
120
121
122
31
123
44
3
90
50
19
124
28
125
71
66
9
115
209
117
64
114
209
209
3 153
6
209
209
86
209
8
11
1
59
26
114
117
209
3
35
74
33
10
3
209
2
205
35
205
3
206
108
38
13
34
38
32
www.mymowerparts.com
26
209
For Parts Call K&T 606-678-9623 or 606-561-4983
REPAIR PARTS
TRACTOR - - MODEL NUMBER SGT18H46C
CHASSIS
KEY
NO.
PART
NO.
DESCRIPTION
1
2
3
6
8
9
10
11
13
17
19
24
25
26
28
29
30
31
33
34
35
36
38
44
50
59
64
66
71
74
86
87
90
108
114
115
117
119
120
121
122
123
124
125
153
205
206
209
212
174620
176554
17060612
155923
126471X
170119
72140608
159954
159953
136673X550
164863
74780616
19131312
73800600
136375
136374X599
167270X550
175315
145244X550
145243X550
72110606
108067X
175710
140675
137304
110436X
170259
169261X010
73640400
73680600
136670X550
136671X550
19091216
74780612
145349
121794X
144283
19092016
137271
137269
137270
157105
157107
74180412
19132203
17490608
170165
17000612
156144
Chassis
Drawbar
Screw 3/8-16 x 3/4
Saddle Flat Lt
Clip Insulator
Dash
Bolt RdHd Sqnk. 3/8-16 Unc x 1
Panel Dash Lh
Panel Dash Rh
Hood
Screw Hwhd Hi-Lo #13-16 x 3/4
Bolt Fin Hex 3/8-16 Unc x 1 Gr. 5
Washer 13/32 x 13/16 x 12 Ga.
Nut Lock Hex w/Insert 3/8-16 UNC
Grill / Lens Asm
Lens Grille
Fender Asm YTGT
Bracket Fender
Footrest Pnt. Lh
Footrest Pnt. Rh
Bolt RdHd Sht. Sqnk. 3/8-16 x 3/4
Nut Pal
Bracket Asm Pivot Mower Rear
Strap Asm Fender
Rod Support Hood
Bushing Snap Split
Dash Lower
Plate Dash Slkscr.
Nut Keps Hex 1/4-20 Unc
Nut Crownlock 3/8-16 Unc
Panel Asm. Pnt. Side Rh
Panel Asm. Pnt. Side Lh
Washer 9/32 x 3/4 x 16 Ga.
Bolt Fin Hex 3/8-16 Unc x 3/4
Bracket Support Dash
Cover Access
Washer Serrated Disc 13/32 x 1
Washer 9/32 x 1-1/4 x 16 Ga.
Rivet Ratchet Female
Washer Nylon
Rivet Ratchet Male
Bracket Asm. Pivot Hood Lh
Bracket Asm. Pivot Hood Rh
Screw Mach Cr. 1/4-20 x 3/4
Washer 13/32 x 1-3/8 x 3 Ga.
Screw Thdrol 3/8-16 x 1/2
Bolt Shoulder 5/16-18
Screw Hex wsh Thdrol 3/8-16 x 3/4
Insert Lens Reflector
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
33
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
REPAIR PARTS
TRACTOR - - MODEL NUMBER SGT18H46C
DRIVE
51
57
51
89
63
69
19
197
16
61
198 161
42
16
169 171
164
21
58
48
42
40
163
38
42
166
82
146
35
165
47
62
8
110
16
51
51
139
103
30
36
120
34
110
53
28
73
110
111
142
131
95
26
29
3
27
135
26 19
77
76
189
2
136
141
36 35
37
19
102
94
96
49
39
156
110
151
51
27
168
10
138
150
41
83
14
202
50
64
56
162
134
65
159 158
19
146
116
66
31
71
70
59
81
139
72
26
77
24
129
22
126
25
93
136
126
127
135
1
84
43
129
128
76
189
126
140
137
131
32
26
129
34
www.mymowerparts.com
55
For Parts Call K&T 606-678-9623 or 606-561-4983
REPAIR PARTS
TRACTOR - - MODEL NUMBER SGT18H46C
DRIVE
KEY PART
NO. NO.
1
------2
3
8
10
14
16
19
21
22
24
25
26
27
28
29
30
31
32
34
35
36
37
38
39
40
41
42
43
47
48
49
50
51
53
55
56
57
58
59
61
62
63
64
65
66
69
70
71
72
73
76
142431
143995
166020
76020416
10040400
73800500
73800600
140845
158274
73350600
106888X
19131316
76020412
175765
71673
123780X
123791X
74760512
175578
120183X
19211616
1572H
165936
74760648
175461
175556
19131312
19111012
127783
154407
123205X
74760624
73680600
105710X
105709X
74760620
161741
158278
169691
17060612
8883R
175412
71170764
10040700
161488
142432
162848
158283
19132012
158282
12000053
DESCRIPTION
Transaxle, Hydro Gear Model 3253000 (Order Parts From Transaxle
Manufacturer)
Spring, Brake Return
Pulley, Hydro
Rod Shift Fender Adjust Yt
Pin, Cotter 1/8 x 1
Washer Lock Hvy Helical
Nut Lock Hx w/Ins. 5/16-18 Unc
Nut, Lock Hex w/Ins. 3/8-16 UNC
Knob
Rod, Brake
Nut, Hex Jam 3/8-16
Spring, Rod, Brake
Washer 13/32 x 13/16 x 16 Ga.
Pin, Cotter 1/8 x 3/4
Rod, Brake, Park
Cap, Brake Parking Black
Bracket, Transaxle, L.H.
Keeper, Belt, Transaxle, L.H.
Bolt Hex Hd. 5/16-18 Unc x 3/4
Shaft, Foot Pedal
Bearing Nylon
Washer 21/32 x 1 x 16 Gauge
Pin,Roll 3/16 x 1
Idler, Flat
Bolt Rdhd 3/8-16 Unc x 3
Spacer
Keeper, Idler
Washer 13/32 x 13/16 x 12 Gauge
Bolt Shoulder 5/16-18 Unc
Pulley, Idler
Bellcrank Clutch Grnd Drv Stl
Retainer, Belt
Bolt, Hex 3/8-16 x 1-1/2
Nut, Crownlock 3/8-16
Link, Clutch
Spring, Return, Clutch
Bolt, Hex 3/8-16 x 1-1/4
V-Belt, Drive
Keeper, Belt, Transaxle, R.H.
Keeper Belt Centerspan
Screw 3/8-16 x 3/4
Cover, Foot Pedal
Pulley, Engine
Bolt, Hex 7/16-20 x 4-1/4
Washer, Lock Hvy Hlcl Spr 7/16
Keeper Belt Engine F-proof
Screw Hex Wsh Hi-Lo 1/4-1/2 Unc
Keeper Belt Engine
Strap Torque Lh Hydro-3000
Washer 13/32 x 1-1/4 x 12 Ga.
Strap Torque Rh Hydro-3000
E-Ring
KEY
NO.
PART
NO.
DESCRIPTION
77
81
82
83
84
89
93
94
95
96
102
103
110
111
116
120
126
127
128
129
131
134
135
136
137
138
139
140
141
142
146
150
151
156
158
159
161
162
163
164
165
166
168
169
171
189
197
198
202
9396E
165598
123782X
19171216
165926
164892X428
142564
140462
158508
4497H
141322
73940800
74760612
123776X
72110610
73900600
1685H
74490548
158284
105529X
10140500
158272
123800X
163168X
19111212
19112016
74780612
4475J
159197
74330516
74490536
175456
19133210
166002
165589
165494
72140406
73680400
74780416
19091010
165623
166880
165492
165581
17490608
160849
169613
169593
72110612
Key Square 1/4 x 2
Shaft Asm Cross Tapered
Spring, Torsion
Washer 17/32 x 3/4 x 16 Gauge
Link Transaxle
Console
Line Fuel Hydro
Fan Hydro
Control Asm Bypass Hydro-3000
Retainer Spring 1" Zinc/cad.
Washer Belliville 1/2 x 1-1/2
Nut Hex Jam Toplock 1/2-20 Unf
Bolt Hex 3/8-16 x 3/4
Bracket, Transaxle, R.H.
Bolt Rdhd Sq Neck 3/8-16 x 1/25
Nut Lock Flg. 3/8-16 Unc
Nut Lock 5/16-18 Nc Thd
Bolt Hex Flghd 5/16-18 x 3.0 Gr. 5
Bracket Neutral Adjust HG-3000
Bolt Shoulder 5/16-18 Unc
Washer Lock 5/16
Rod Actuator Bypass Hydro-3000
Washer 1-1/32 x 1-5/8 x 16 Gauge
Washer Axle Flange
Washer 11/32 x 3/4 x 12 Ga.
Washer 11/32 x 1.25 x 16 Ga.
Bolt Fin Hex 3/8-16 x 3/4
Bushing Pinion Sector
Pin Hitch
Bolt 5/16 x 24 x 1
Bolt Hex Flghd 5/16-18 x 2-1/4
Spacer
Washer 13/32 x 2 x 10 Ga.
Washer Srrted 5/16ID x 1.125
Bracket Shift Mount
Hub Tapered Flange Shift Lt
Bolt Rdhd Sqnk 1/4-20 x 3/4 Gr 5
Nut Crownlock 1/4-20 Unc
Bolt Hex Fin 1/4-20 Unc x 1 Gr 5
Washer 5/8 x .281 x 10 Ga
Bracket Pivot Lever
Screw 5/16-18 x 5/8
Bolt Shoulder 5/16-18 x .561
Plate Fastening Lt
Screw Thdrol 3/8-16 x 1/2 Ty-Tt
Washer Spacer Axle
Nyliner Snap-In 5/8" Id
Washer Nyl 7/8 Id x .105
Bolt Carr Sh 3/8-16 x 1-1/2 Gr.5
NOTE: All component dimensions given in U.S. inches\
1 inch = 25.4 mm
35
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
REPAIR PARTS
TRACTOR - - MODEL NUMBER SGT18H46C
STEERING ASSEMBLY
38 38
12
39
1
41
42
37
37
36
88
91
43
71
29
67
67
68
67
46
29
8
47
6
9
17
13
65
46
85
2
8
7
85
6
9
9
5
47
7
3
32
9
5
92
11
82
29
29
4
26
43
29
29
15
40
43
15
28
15
10
30
36
www.mymowerparts.com
6
8
For Parts Call K&T 606-678-9623 or 606-561-4983
REPAIR PARTS
TRACTOR - - MODEL NUMBER SGT18H46C
STEERING ASSEMBLY
KEY
NO.
PART
NO.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
15
17
26
28
29
30
32
36
37
38
39
40
41
42
43
46
47
65
67
68
71
82
85
88
91
92
140044X428
154427
156486
157475
6266H
121748X
19272016
12000029
3366R
175122
10040600
73940800
136518
145212
177883
126847X
19131416
17060612
76020412
130465
145207
152927
140045X428
100712K
7810H
100711L
177776X428
121749X
121232X
6855M
160367
72140618
169828
175146
169835
133835
175118
175553
169829
Wheel Steering Auto Black
Axle Asm Front
Spindle Asm Lh
Spindle Asm Rh
Bearing Race Thrust Harden
Washer 25/32 X 1 5/8 X 16ga
Washer 27/32 X 1 1/4 X 16 Ga
Ring Klip #t5304-75
Bearing Col Strg Blk
Link Drag
Lockwasher
Nut Hex Jam Toplock 1/2-20 Unf
Spacer Bearing Axle Front
Nut Hex Flange Lock
Shaft Asm Strg
Bushing Rod Tie Blk Lt
Washer 13/32 X 7/8 X 16ga
Screw 3/8-16x3/4
Pin
Rod Tie Wire Form 19 75 Mech
Bushing Strg
Screw TT #10-32 x 5 x 3/8 Flange
Insert Cap Strg
Washer .53 x 2.25 x .160 Zinc
Locknut Center
Adaptor Wheel Strg 640/ 635id
Boot Dash Steering
Washer 25/32 X 1 1/4 X 16 Ga
Cap Spindle Fr Top Blk
Fitting Grease
Spacer Axle
Bolt Rdhd Sq 3/8-16 Unc x 2-1/4
Brace Axle Front
Steering Asm
Bracket Susp Chassis Front
Fastner Christmas Tree
Bolt Shoulder 7/16-20
Clip Steering
Axle Rear 16" Tires GTV
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
37
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
REPAIR PARTS
TRACTOR - - MODEL NUMBER SGT18H46C
ENGINE
106
3
2
1
107
8
14
38
13
10
81
25
105
105
6
5
16
26
45
62
99
72
32
31
45
34
100
33
37
39
40
41
33
45
23
29
OPTIONAL EQUIPMENT
4
Spark Arrester
38
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
REPAIR PARTS
TRACTOR - - MODEL NUMBER SGT18H46C
ENGINE
KEY
NO.
PART
NO.
1
2
3
176174
17720410
-------
4
5
6
8
10
13
14
16
23
25
26
29
31
32
33
34
37
38
39
40
41
45
62
72
81
99
100
105
106
107
149723
174703
174704
171877
176252
35-414
148456
11050600
169837
132778
73920600
137180
151346
161493
123487X
106082X
8543R
148315
109227X
3645J
139277
17000612
10040500
71070512
73510400
160771
160772
17120616
160-82
42-823
DESCRIPTION
Control, Throttle
Screw, Hex Head, Thread Cutting 1/4-20 x 5/8
Engine, Tec Model Number TVT691
(Order Parts From Engine Manufacturer)
Muffler
Tube, Exhaust, LH
Tube, Exhaust, RH
Bolt 5/16-18 UNC x 3/4 w/Sems
Shield, Heat
Muffler Gasket
Tube Drain Oil Easy
Washer, Lock, External Tooth 3/8
Shield, Browning / Debris Guard
Choke Control
Nut, Keps 3/8-24 UNF
Kit, Spark Arrestor
Tank Fuel 3 50 Rear
Cap Fuel Gauge
Clamp, Hose
Pad, Spacer
Line, Fuel
Plug Drain Oil Easy
Pad, Idler
Bushing
Stem, Fuel Tank
Screw Hex wsh Thdrol 3/8-16 x 3/4
Washer Lock 5/16
Screw Hex Hd Cap 5/16-18 x 3/4
Nut Keps Hex 1/4-20 Unc
Bracket Asm Pivot Lh Raised
Bracket Asm Pivot Rh Raised
Screw 3/8-16 x 1
Control Cover
Screw
NOTE: All component dimensions given in U.S. inches.
1 inch = 25.4 mm
39
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
REPAIR PARTS
TRACTOR - - MODEL NUMBER SGT18H46C
SEAT ASSEMBLY
1
18
28
28
14
7
7
10
5
6
22
27
2
21
24
5
16
25
15
11
13
17
12
KEY
NO.
PART
NO.
DESCRIPTION
1
2
5
6
7
10
11
12
13
14
15
140118
140551
145006
73800600
124181X
174894
166369
121246X
121248X
72050412
121249X
Seat
Pivot Bracket, Seat
Clip, Push-in Hinged
Nut, Lock Hex w/Ins 3/8-16 UNC
Spring, Seat
Pan, Seat
Knob, Seat, Black
Bracket, Switch Mounting
Bushing, Snap, Black, Nylon
Bolt, Carriage 1/4-20 x 1-1/2
Spacer, Split
KEY
NO.
PART
NO.
DESCRIPTION
16
17
18
21
22
24
25
27
28
123740X
123976X
124238X
171852
73800500
19171912
127018X
17490608
171877
Spring
Locknut, Flange 1/4 Grade 5
Cap Spring Seat Blk 1.75 x 1.0
Bolt, Shoulder 5/16-18 Unc -2A
Nut Lock Hex W/Ins 5/16-18 Unc
Washer 17/32 x 1-3/16 x 12 Gauge
Bolt, Shoulder 5/16-18 x .62
Screw Thdrol 3/8-16 x 3/4
Bolt 5/16-18 UNC x 3/4 w/Sems
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
40
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
REPAIR PARTS
TRACTOR - - MODEL NUMBER SGT18H46C
DECALS
4
11
2
2
7
3
17
17
1
12
14
8
13
6
13
10
19
KEY
NO.
PART
NO.
DESCRIPTION
KEY
NO.
PART
NO.
DESCRIPTION
1
2
3
4
6
7
8
10
11
171448
164022
177174
177173
140837
157002
4900J
139346
162398
Decal Fender
Decal Side Panel
Decal Hood LH
Decal Hood RH
Decal Parking Brake
Decal Danger Fender English
Decal Clutch/brake English
Decal V-Belt Sch
Decal Steering
12
13
14
17
19
-----
156835
106202X
145005
177512
162391
142341
157199X428
138311
178387
Decal Oper sDL Eng
Reflector Taillight
Decal, Btry Dngr/Psn
Decal Fender Side
Decal Deck
Decal Cntrl Movement
Pad, Footrest
Decal Handle Lft Height Adjust
Manual, Owner's (English)
WHEELS & TIRES
KEY
NO.
1
2
1
2
3
4
5
6
7
8
9
10
11
--
5,8
4,10
7
3,9
6
11
PART
NO.
59192
65139
106230X
59904
106228X427
278H
9040H
124074X427
124106X
7154J
104757X428
144334
DESCRIPTION
Cap Valve Tire
Stem Valve
Tire Front
Tube Front (Service Item Only)
Rim Asm 8" front
Fitting Grease (Front Wheel Only)
Bearing Flange (Front Wheel nly)
Rim Asm 12" rear
Tire R 23 x 8.5-12 C Service
Tube Rear (Service Item Only)
Cap Axle Blk 1 50 X 1 00
Sealant, Tire (1 Doz. Tube)
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
41
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
REPAIR PARTS
TRACTOR - - MODEL NUMBER SGT18H46C
MOWER LIFT
29
28
27
25 24
23
7
8
9
41
1
10
49
47
37
14
38
30
40
36
50
13
26
46
2
11
6
12
13
19
13
20
15
31
32
13
19
31
32
44
42
43
39
42
www.mymowerparts.com
20
17 18 20
16
20
15
For Parts Call K&T 606-678-9623 or 606-561-4983
REPAIR PARTS
TRACTOR - - MODEL NUMBER SGT18H46C
MOWER LIFT
KEY
NO.
PART
NO.
DESCRIPTION
1
2
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
23
24
25
26
27
28
29
30
31
32
36
37
38
39
40
41
42
43
44
46
47
49
50
121006X
159188
74780624
109413X
124526X
122364X
2876H
145537
145536
4939M
159189
173288
73350800
175689
73800800
139868
163552
110807X
19131016
137150
76020308
160985
73350600
138057
150233
169865
73540600
155097
123935X
17060516
142992
19112410
123934X
73680600
19131612
72240608
12000022
19292016
145212
110452X
Rod Assembly, Lever
Shaft Assembly, Lift
Bolt, Hex Head, Fin. 3/8-16 x 1-1/2
Grip Handle
Button Plunger Black
Plunger Lever Lift
Spring
Link, Lift, LH
Link, Lift, RH
Retainer Spring
Lever Assembly, Lift, RH
Link, Front
Nut, Hex, Jam 1/2-13 UNC
Trunnion
Nut Lock W/Wsh 1/2-13 Unc
Arm, Suspension, Rear
Retainer Spring
Nut Special
Washer 13/32 x 5/8 x 16 Ga.
Spring Compression
Pin Cotter
Rod Adj. Lift
Nut Hex Jam 3/8-16 Unc
Knob Inf. 3/8-16 Unc
Trunnion Infin Height
Bearing
Nut, Crownlock 3/8-24
Pointer Height Indicator
Plug Hole
Screw 5/16-18 x 1
Stop Over Center
Washer 11/32 x 1-1/2 10 Ga.
Scale Ind. Height
Nut, Crownlock 3/8-16 UNC
Washer 13/32 x 1 x 12 Ga.
Bolt, Carriage 3/8-16 x 1.00
E-Ring
Washer
Nut Hex Flange Lock
Nut Push
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
43
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
REPAIR PARTS
TRACTOR - - MODEL NUMBER SGT18H46C
MOWER DECK
67
157
158
156
153
151
155
46
152
41
135
153 154
49
136
42
45
41
69
85
127
46
36
37
42
43
45
40
59
126
58
44
33
44
129
39
32
116
50
31
130
35
72
52
38
30
62
33
32
61
62 60
132
31
34
117
47
30
90
119
91
180
93
94
93
180
21
95
90
21
118
82
3
18
134
5
133
6
26
21
1
22
23
24
25
29
28
117
27
19
15
14
18
16
20
48
13
18
11
10
9
8
44
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
REPAIR PARTS
TRACTOR - - MODEL NUMBER SGT18H46C
MOWER DECK
KEY
NO.
PART
NO.
DESCRIPTION
KEY
NO.
PART
NO.
1
3
5
6
8
9
10
11
13
14
15
16
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
156948
138457
4939M
130832
850857
10030600
140296
176084
137553
137152
110485X
174493
72140505
132827
145055
73680500
134753
131267
105304X
149287
110452X
166883X428
19111016
131491
157722
129963
153531
178342
144945
17490628
19131316
131494
156085
144917
137273
17060620
165723
144949
133943
145059
137729
144959
139573
Deck Asm., Mower 46"
Bracket Asm., Sway Bar
Retainer Spring
Arm, Suspension, Rear (Sway Bar)
Bolt, Patched 3/8-24 x 1-1/4 Gr. 8
Washer, Lock Hvy., Unplated 3/8
Washer, Hard Blade, Mower Vented
Blade Hi-Perf 46"
Shaft Asm. w/Lower Bearing
Housing, Mandrel
Bearing, Ball, Mandrel
Stripper, Mower Round
Bolt, Carriage 5/16-18 x 5/8
Bolt, Hex Head, Shoulder 5/16-18
Baffle, Vortex Mower 46"
Nut, Crownlock 5/16-18 UNC
Stiffiner, Bracket
Bracket, Deflector
Cap, Sleeve
Spring, Torsion, Deflector
Nut, Push
Shield, Deflector Mower
Washer 11/32 x 5/8 x 16 Ga.
Rod, Hinge
Screw, Thdroll Washer Head
Washer, Spacer Mower Vented
Pulley, Mandrel
Nut, Flg. Top Lock
Anchor, Spring Deck 46"
Screw, Thdroll 3/8-16 x 1-3/4 Tytt
Washer 13/32 x 1 x 16 Ga.
Pulley, Idler, Flat
Keeper, Belt, Idler
Pulley, Idler, Driven
Spring, Secondary 44/46/50 Vent
Screw 3/8-16 x 1-1/4
Spacer, Retainer
Arm, Idler Secondary
Washer, Hardened
Cover, Mandrel Deck
Screw, Thdroll. 1/4-20 x 5/8
V-Belt, Mower, Secondary
V-Belt, Mower, Primary
49
73680600
Nut, Crownlock 3/8-16 UNC
50
72110612
Bolt, Carriage 3/8-16 x 1-1/2 Gr. 5
52
156493
Pulley Idler
58
165906
Rod Brake 46"
59
157034
Guide Bolt 46" Mower Dr
60
156722
Arm Asm Brake 46"
61
161315
Bolt Shld 5/16-18
62
131870
Spring Return
67
106932X
Knob Rd 3/8-16 Plstc Thds Blk
69
73350600
Nut Hex Jam 3/8-16 Unc
72
19131316
Washer 13/32 x 1 x 16 Ga.
82
4497H
Retainer Spring
85
10040600
Washer Lock 3/8
90
17060612
Screw 3/8-16 x 3/4
91
175746
Bracket Asm. Noseroller Lh
93
19171416
Washer 17/32 x 7/8 x 16 Ga.
94
132264
Roller Nose
95
175747
Bracket Asm. Noseroller Rh
116 4898H
Bolt, Shoulder
117 165746
Gauge Wheel
118 73930600
Nut, Centerlock 3/8-16 UNC
119 19121414
Washer 3/8 x 7/8 x 14 Ga.
126 156472
Arm, Idler, Primary Deck 46"
127 146763
Pulley, Idler, V-Groove Dim. 4.25
129 19133808
Washer 13/32 x 2-3/8 x 8 Ga
130 165891
Bolt Carriage Idler
132 165890
Arm Spring Brake Mower
133 165904
Bracket Anchor Cable 46"
134 17490512
Screw Thdrol5/16-18 x 3/4
135 165898
Retainer Spring Yellow
136 19091216
Washer 9/32 x 3/4 x 16 Ga
151 169670
Bracket Clutch Cable
152 170328
Clutch Cable 38"/46"
153 169674
Washer Flat 3/8" Type B
154 169675
Spring Retainer
155 169671
Spring Retension Q
156 169672
SPacer Clutch Cable
157 169669
Rod Clutch Cable 3/8"
158 17720410
Screw Hex Thd Cut 1/4-20 x 5/8
-143651
Mandrel Asm 44"/46"/50" Service
-172497
Replacement Mower, Complete
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
45
www.mymowerparts.com
DESCRIPTION
For Parts Call K&T 606-678-9623 or 606-561-4983
LIMITED WARRANTY
The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in
materials and workmanship. For a period of two (2) years from date of purchase by the original consumer purchaser, we will
repair or replace, at our option, without charge for parts or labor incurred in replacing parts, any part which we find to be
defective due to materials or workmanship. This Warranty is subject to the following limitations and exclusions.
1. This warranty does not apply to the engine, other than EHP manufactured transaxle/transmission components,
battery (except as noted below) or components parts thereof. Please refer to the applicable manufacturer's
warranty on these items.
2. Transportation charges for the movement of any power equipment unit or attachment are the responsibility of
the purchaser. Transportation charges for any parts submitted for replacement under this warranty must be
paid by the purchaser unless such return is requested by Electrolux Home Products.
3. Battery Warranty: On products equipped with a Battery, we will replace, without charge to you, any battery
which we find to be defective in manufacture, during the first ninety (90) days of ownership. After ninety (90)
days, we will exchange the Battery, charging you 1/12 of the price of a new Battery for each full month from the
date of the original sale. Battery must be maintained in accordance with the instructions furnished.
4. The Warranty period for any products used for rental or commercial purposes is limited to 90 days from the date
of original purchase.
5. This Warranty applies only to products which have been properly assembled, adjusted, operated, and maintained in accordance with the instructions furnished. This Warranty does not apply to any product which has
been subjected to alteration, misuse, abuse, improper assembly or installation, delivery damage, or to normal
wear of the product.
6. Exclusions: Excluded from this Warranty are belts, blades, blade adapters, normal wear, normal adjustments,
standard hardware and normal maintenance.
7. In the event you have a claim under this Warranty, you must return the product to an authorized service dealer.
Should you have any unanswered questions concerning this Warranty, please contact:
In Canada contact:
Electrolux Home Products
a division of WCI Outdoor Products, Inc.
Outdoor Products Customer Service Dept.
250 Bobby Jones Expressway
Augusta, GA 30909 USA
Electrolux Home Products
a division of WCI Outdoor Products, Inc.
7075 Ordan Drive
Mississauga, Ontario
L5T 1K6
giving the model number, serial number and date of purchase of your product and the name and address of the authorized
dealer from whom it was purchased.
THIS WARRANTY DOES NOT APPLY TO INCIDENTAL OR CONSEQUENTIAL DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN FOR OUR EXPRESSED WARRANTIES. Some areas
do not allow the limitation of consequential damages or limitations of how long an implied Warranty may last, so the above
limitations or exclusions may not apply to you. This Warranty gives you specific legal rights, and you may have other rights
which vary from locale to locale.
This is a limited Warranty within the meaning of that term as defined in the Magnuson-Moss Act of 1975.
46
www.mymowerparts.com
47
www.mymowerparts.com
15 MAX.
SIGHT AND HOLD THIS LEVEL WITH
SKY LINE OR TREE.
CUT
OUT
ON D
THIS
OTT
IS A
ED L
15 S
INES
LOP
E
Operate your Tractor up and down the face of slopes (not
greater than 15 ), never across the face. Make turns gradually to prevent tipping or loss of control. Exercise extreme
caution when changing direction on slopes.
SIGHTING
GUIDE
ONLY RIDE UP AND DOWN HILL,
NOT ACROSS HILL
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION
For Parts Call K&T 606-678-9623 or 606-561-4983
For Parts Call K&T 606-678-9623 or 606-561-4983
®
www.mymowerparts.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement