GE JN327HCC 30" Standard Range Hood: Bisque on Bisque

GE JN327HCC 30" Standard Range Hood: Bisque on Bisque
Range Hoods
www.GEAppliances.com
Safety Information . . . . . . . . 2, 3
Operating/Care and
Cleaning Instructions
Charcoal Filter . . . . . . . . . . . . . . .5
Grease Filter . . . . . . . . . . . . . . . .4
Hood Light . . . . . . . . . . . . . . . . .5
Hood Surfaces . . . . . . . . . . . . . . .5
Controls . . . . . . . . . . . . . . . . . . . .4
Installation Instructions . . .6–16
Owner’s Manual and
Installation Instructions
JN327–Recirculation only
JV338*–Vent options only
JV347*–Vent & Recirculation
options
JV367*–Vent & Recirculation
options
RN328–Recirculation only
Consumer Support
Consumer Support . . .Back Cover
Warranty . . . . . . . . . . . . . . . . . . 19
*
Write the model and serial numbers here:
Model # __________________________
Serial # __________________________
You can find them on a label on the
back wall of the hood.
164D4290P393
49-80242 12-03 JR
Safety Instructions
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
SAFETY PRECAUTIONS
WARNING – TO REDUCE THE RISK OF FIRE,
Operating Instructions
ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
A. Use this unit only in the manner intended
by the manufacturer. If you have questions,
contact the manufacturer.
B. Before servicing or cleaning unit, switch power off
at service panel and lock the service disconnecting
means to prevent power from being switched on
accidentally. When the service disconnecting
means cannot be locked, securely fasten a
prominent warning device, such as a tag, to
the service panel.
C. Do not use this unit with any solid-state speed
control device.
D. If using a cord connection kit, use only with range
hood cord-connection kit JXHC1 that has been
investigated and found acceptable for use with
this model range hood.
E. This unit must be grounded.
CAUTION – FOR GENERAL VENTILATING USE
ONLY. DO NOT USE TO EXHAUST HAZARDOUS OR
EXPLOSIVE MATERIALS AND VAPORS.
Installation Instructions
WARNING –
Consumer Support
TO REDUCE THE RISK OF
INJURY TO PERSONS IN THE EVENT OF A RANGE TOP
GREASE FIRE, OBSERVE THE FOLLOWING*:
A. SMOTHER FLAMES with a close-fitting lid,
cookie sheet or metal tray, then turn off the
burner. BE CAREFUL TO PREVENT BURNS.
If the flames do not go out immediately,
EVACUATE AND CALL THE FIRE
DEPARTMENT.
B. NEVER PICK UP A FLAMING PAN—
You may be burned.
C. DO NOT USE WATER, including wet
dishcloths or towels—a violent steam
explosion will result.
D. Use an extinguisher ONLY if:
1. You know you have a Class ABC extinguisher,
and you already know how to operate it.
2. The fire is small and contained in the area
where it started.
3. The fire department is being called.
4. You can fight the fire with your back to an exit.
* Based on “Kitchen Firesafety Tips” published
by NFPA.
2
WARNING –
TO REDUCE THE RISK OF
A RANGE TOP GREASE FIRE:
A. Never leave surface units unattended at high
settings. Boilovers cause smoking and greasy
spillovers that may ignite. Heat oils slowly on low
or medium settings.
B. Always turn hood ON when cooking at high heat
or when cooking flaming foods.
C. Clean ventilating fans frequently. Grease should
not be allowed to accumulate on fan or filter.
D. Use proper pan size. Always use cookware
appropriate for the size of the surface element.
WARNING –
TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
A. Installation work and electrical wiring must be
done by qualified person(s) in accordance with
all applicable codes and standards, including
fire-rated construction.
B. Sufficient air is needed for proper combustion
and exhausting of gases through the flue
(chimney) of fuel burning equipment to prevent
back drafting. Follow the heating equipment
manufacturer’s guideline and safety standards
such as those published by the National Fire
Protection Association (NFPA), the American
Society for Heating, Refrigeration and Air
Conditioning Engineers (ASHRAE) and the
local code authorities.
C. When cutting or drilling into wall or ceiling, do
not damage electrical wiring and other hidden
utilities.
D. Ducted fans must always be vented to the
outdoors.
WARNING –
TO REDUCE THE RISK OF FIRE,
USE ONLY METAL DUCTWORK.
■ Do not attempt to repair or replace any part of
your hood unless it is specifically recommended in
this guide. All other servicing should be referred to
a qualified technician.
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
READ AND SAVE THESE INSTRUCTIONS
Safety Instructions
INSTRUCTIONS DE SÉCURITÉ IMPORTANTES.
LISEZ TOUTES LES INSTRUCTIONS AVANT D’UTILISER.
PRÉCAUTIONS EN MATIÈRE DE SÉCURITÉ
AVERTISSEMENT – POUR RÉDUIRE LE AVERTISSEMENT – RÉDUISEZ LE
RISQUE D’INCENDIE, DE SECOUSSE ÉLECTRIQUE OU DE
BLESSURE CORPORELLE, OBSERVEZ LES PRÉCAUTIONS
SUIVANTES :
ATTENTION – UNIQUEMENT À USAGE DE
AVERTISSEMENT – POUR RÉDUIRE LE
RISQUE DE BLESSURE CORPORELLE SI DE LA GRAISSE
PREND FEU SUR LA SURFACE DE CUISSON DU FOUR,
SUIVEZ LES INSTRUCTIONS SUIVANTES* :
RISQUE D’INCENDIE, DE SECOUSSE ÉLECTRIQUE OU DE
BLESSURE CORPORELLE, OBSERVEZ LES PRÉCAUTIONS
SUIVANTES :
A. Vous devez faire exécuter tous les travaux
d’installation et de câblage électrique par une
personne qualifiée, conformément à tous les codes
et les normes en vigueur, en particulier ceux de
construction relatifs aux incendies.
B. Vous devez assez d’air pour avoir une bonne
combustion et permettre l’évacuation des gaz par le
conduit de cheminée du matériel de combustion du
carburant, afin d’éviter tout retour d’air. Suivez les
directives du fabricant de matériel de combustion et
les normes de sécurité comme celles publiées par la
National Fire Protection Association (NFPA),
l’American Society for Heating, Refrigeration and
Air Conditioning Engineers (ASHRAE), ainsi que les
modalités des codes locaux.
C. Si vous faites un trou ou une ouverture dans un mur
ou un plafond, n’endommagez pas les fils électriques
et les autres installations cachées de service public.
D. Vous devez toujours alimenter les ventilateurs dans
les conduits en air en provenance de l’extérieur.
AVERTISSEMENT – POUR RÉDUIRE
LE RISQUE D’INCENDIE, N’UTILISEZ QUE DES CONDUITS
EN MÉTAL.
■ N’essayez jamais de remplacer ou de réparer un
Consumer Support
A. ÉTOUFFEZ LES FLAMMES avec un couvercle qui
convient, une tôle à biscuits ou un plateau en métal,
puis éteignez le brûleur. FAITES BIEN ATTENTION
DE NE PAS VOUS BRÛLER. Si les flammes ne
s’éteignent pas immédiatement, SORTEZ ET
APPELEZ LES POMPIERS.
B. NE DÉPLACEZ JAMAIS UNE CASSEROLLE QUI
FLAMBE – Vous pouvez vous brûler.
C. N’UTILISEZ JAMAIS D’EAU, en particulier de
serviette ou de chiffon mouillé – il se produira une
explosion violente de vapeur brûlante.
D. N’UTILISEZ UN EXTINCTEUR que si :
1. Vous avez un extincteur de classe ABC et vous
savez comment l’utiliser;
2. Le feu est réduit et confiné à l’endroit où il a
commencé;
3. Vous avez déjà appelé les pompiers;
4. Vous combattez les flammes en tournant le dos à
une sortie.
* Basé sur l’ouvrage intitulé «Kitchen Fire Safety Tips»
publié par la NFPA.
AVERTISSEMENT – POUR RÉDUIRE LE
Installation Instructions
VENTILATION GÉNÉRALE. N’UTILISEZ JAMAIS POUR
L’ÉCHAPPEMENT DE MATIÈRES ET DE VAPEURS
EXPLOSIVES.
A. Ne laissez jamais sans surveillance les unités de
cuisson de surface à une température élevée. Le
bouillonnement occasionne des débordements
fumants et graisseux qui peuvent prendre feu.
Chauffez à feu doux les substances huileuses,
avec un réglage bas ou moyen.
B. Mettez toujours la hotte en marche quand vous
cuisinez à haute température ou quand vous cuisinez
des aliments qui ont des flammes.
C. Nettoyez les mécanismes de ventilation
fréquemment. Il ne faut pas permettre une
accumulation de graisse sur le ventilateur ou
sur le filtre.
D. Utilisez une casserole de bonne taille. Utilisez
toujours un ustensile de cuisine qui convienne au
diamètre de l’élément de cuisson.
Operating Instructions
A. N’utilisez cet appareil que de la manière prévue
par le fabricant. Si vous avez des questions, appelez
le fabricant.
B. Avant de réparer ou de nettoyer votre appareil,
débranchez le courant au niveau du panneau
de service et verrouillez les mécanismes de
débranchement de service pour éviter tout
branchement accidentel au courant. Si vous ne
pouvez pas verrouiller les mécanismes de
débranchement de service, attachez soigneusement
un avertissement bien visible, comme une étiquette,
au panneau de service.
C. N’utilisez jamais cet appareil avec un mécanisme
de réglage de la vitesse à semi-conducteurs.
D. Si vous utilisez l’ensemble de cordon de
raccordement, utilise seulement avec l’ensemble de
cordon de raccordement pour hotte JXHC1. Suite à
un examen technique, l’article JXHC1 s’est avéré
compatible avec ce modèle de hotte.
E. Cet appareil doit être bien mis à la terre.
RISQUE D’UN FEU DE GRAISSE SUR LA SURFACE DE
CUISSON DU FOUR :
élément de votre hotte si le présent manuel ne le
recommande pas expressément. Tout autre entretien
doit être effectué par un technicien qualifié.
LISEZ ET SUIVEZ ATTENTIVEMENT CES INSTRUCTIONS.
LISEZ ET CONSERVEZ CES INSTRUCTIONS
3
Safety Instructions
Using the hood controls.
Throughout this manual, features and appearance may vary from your model.
Switch Pad Controls (on some models)
Control Knobs (on some models)
ON
OFF
Operating Instructions
LO
MED
HI
OFF
ON
NITE
OFF
OFF
LO
FAN Control
LIGHT Control
Turn to HI, MED or LO as needed.
Continuous use of the fan system while cooking
helps keep the kitchen comfortable and less
humid. It also reduces cooking odors and soiling
moisture that create a frequent need for cleaning.
Press the pad at the top to turn the light ON.
LIGHT Control
Turn to ON while cooking or to NITE for use as a
night light.
FAN Control
Press the pad at the top to turn the fan on HI and
at the bottom to turn it on LO. The center position
is OFF.
Continuous use of the fan system while cooking
helps keep the kitchen comfortable and less
humid. It also reduces cooking odors and soiling
moisture that create a frequent need for cleaning.
Care and cleaning of the vent hood.
Be sure electrical power is off and all surfaces are cool before cleaning or servicing any part of the
vent hood.
Reusable Metal Grease Filter–Ducted Installations Only
Consumer Support
Installation Instructions
HI
Grease filter
4
The efficiency of your hood
depends on a clean filter.
Frequency of cleaning depends on
hood use and the type of cooking
you do. However, the grease filter
should be cleaned at least once a
month.
To clean:
Soak and then agitate it in a hot
water and detergent solution.
Light brushing can be used to
remove embedded dirt. Rinse,
shake and let it dry before
replacing.
To remove:
Pull down on the center of the
front edge of the filter. The filter
will then slip out of the retaining
tabs on the back.
NEVER OPERATE THE HOOD
WITHOUT THE FILTER IN PLACE.
With careful handling, the metal
filter will last for years. If a new
replacement filter becomes
necessary, order the part from
your dealer. Order genuine GE
part number WB02X8391.
To replace:
Slip the back edge of the filter
into the retaining tabs and push
the front edge up until it snaps
into place.
Safety Instructions
Charcoal Filter–Recirculating Installations Only
The charcoal filter cannot be
cleaned. It must be replaced. Order
filter no. WB02X10700. Replacement
filters can be ordered from your GE
supplier.
Replaceable charcoal filter
NOTE: DO NOT rinse, or put charcoal filters in
an automatic dishwasher.
To remove:
Pull down on the center of the
front edge of the filter. The filter
will then slip out of the retaining
tabs on the back.
To replace:
Slip the back edge of the filter
into the retaining tabs and push
the front edge up until it snaps
into place.
If the hood is not vented to
the outside, the air will be
recirculated through a disposable
charcoal filter that helps remove
smoke and odors.
Painted Surfaces
NOTE: When cleaning, take care not
to come in contact with filters and
other non-enameled surfaces.
Clean grease-laden surfaces of the
hood frequently. To clean the hood
surface, use a hot, damp cloth with a
mild detergent suitable for painted
surfaces. About one tablespoon of
ammonia may be added to the water.
Use a clean, hot, damp cloth to
remove soap. Dry with a dry,
clean cloth.
CAUTION: When cleaning the hood
surfaces, be certain that you do not
touch the light bulb with moist hands or
cloth. A warm or hot light bulb may break
if touched with a moist surface. Always
let the light bulb cool completely before
cleaning around it.
Hood Light
Light cover
CAUTION: Let the light bulb cool
completely before removing.
A warm or hot bulb may break
if touched with a moist cloth
or hand.
To remove the light cover
(on some models):
• Press the sides with two fingers
until the side prongs are
released.
Remove the bulb and replace with
an ordinary screw-base light bulb,
not more than 60 watts.
• Lift the light cover and slide it
toward you in one motion.
Consumer Support
To replace the light cover:
• Insert the prong located at the
end of the cover into the top
opening.
Installation Instructions
Do not use steel-wool pads or other
abrasive cleaners. They will scratch
the surface.
Operating Instructions
The charcoal filter should be
replaced after 6 to 12 months
(depending on hood usage).
• Gently push the cover up and
press the sides to fit the side
prongs into the side openings.
• Release and the cover will lock
in position.
5
Installation
Instructions
Range Hood
Questions? Visit our Website at: www.geappliances.com or Call GE Answer Center at 800.626.2000
BEFORE YOU BEGIN
DUCTWORK REQUIREMENTS
Read these instructions completely and carefully.
NOTE: Read the ductwork sections only if you do not
have existing ductwork. If you have existing ductwork,
skip to the “Damage” section and proceed.
•
IMPORTANT – Save these
instructions for local inspector’s use.
•
•
•
•
•
•
•
The venting system must exhaust to the outside.
IMPORTANT – Observe all
This hood can be vented vertically through upper
cabinets or horizontally through an outside wall.
Ductwork is not included.
governing codes and ordinances.
Note to Installer – Be sure to leave these
instructions with the Consumer.
Note to Consumer – Keep these instructions
for future reference.
Skill level – Installation of this appliance requires
basic mechanical and electrical skills.
Completion time – 30 minutes–3 hours
Proper installation is the responsibility of the
installer.
Product failure due to improper installation is not
covered under the Warranty.
Exhaust connection:
The hood exhaust has been designed to mate with
standard 31⁄4″ x 10″ rectangular ducting or 7″ diameter
round ducting.
If a 6″ round duct is required, a rectangular-to-round
transition adaptor must be used*. Do not use less than
a 6″ diameter duct.
Maximum duct length:
For satisfactory air movement, the total duct length
of a 31⁄4″ x 10″ rectangular, 6″ or 7″ diameter round
duct should not exceed 65 equivalent feet. See the
WORKSHEET–CALCULATE TOTAL EQUIVALENT
DUCTWORK LENGTH section.
FOR YOUR SAFETY:
NOTE: It is important that ducting be installed using
the most direct route and with as few elbows as possible.
This ensures clear venting of exhaust and helps prevent
blockages. Also, make sure dampers swing freely and
nothing is blocking the ducts.
WARNING – Before beginning the
installation, switch power off at service panel and lock
the service disconnecting means to prevent power
from being switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a prominent warning device, such as a tag,
to the service panel.
Elbows, transitions, wall and roofcaps, etc.,
present additional resistance to airflow and are
equivalent to a section of straight duct longer than their
actual physical size. When calculating the total duct
length, add the equivalent lengths of all transitions and
adaptors plus the length of all straight duct sections. The
charts on the following pages show you how to calculate
total equivalent ductwork length using the approximate
feet of equivalent length of some typical ducts.
OPTIONAL POWER CORD KIT JXHC1
An optional Power Cord Connection Kit, model
JXHC1, is available at extra cost from your GE
supplier for installation using a standard 3-prong,
grounded wall outlet. Follow the Installation
Instructions packed with the kit to connect the power
cord to the range hood.
* IMPORTANT: If a rectangular-toround transition adaptor is used, the
bottom corners of the damper will
have to be cut to fit, using the tin
snips, in order to allow free
movement of the damper.
Equivalent lengths of duct pieces
are based on actual tests and reflect
requirements for good venting
performance with any hood.
6
Installation Instructions
Follow the guidelines for proper duct sizing in the ducting charts.
DUCTING CHART:
Flow vs. equivalent feet of duct length
CFM
300
250
JV347
200
JV338
150
100
50
0
0
20
40
60
80
100
Equivalent Feet of Duct Length
MAXIMUM DUCT LENGTH: For satisfactory air movement, the total duct length of a 31⁄4″ x 10″ rectangular,
6″ or 7″ diameter round duct should not exceed 65 equivalent feet.
7
Installation Instructions
WORKSHEET—CALCULATE TOTAL EQUIVALENT DUCTWORK LENGTH
DUCT
PIECES
EQUIVALENT NUMBER
LENGTH
x USED
= TOTAL
31⁄4″ x 10″
Rect.,
straight
1 Ft.
7″ Round,
straight
1 Ft.
6″ Round,
straight
1 Ft.
31⁄4″ x 10″
Rect. 90°
elbow
8.5 Ft.
x (
)
=
Ft.
31⁄4″ x 10″
Rect. 45°
elbow
7 Ft.
x (
)
=
Ft.
31⁄4″ x 10″
Rect. 90°
flat elbow
24 Ft.
x (
)
=
Ft.
31⁄4″ x 10″
Rect.
wall cap
with
damper
45 Ft.
(7 ft. w/o
damper)
x (
)
=
Ft.
x (
)
=
Ft.
31⁄4″ x 10″
Rect. to
6″ round
transition
4.5 Ft.
x (
)
=
Ft.
31⁄4″ x 10″
Rect. to
6″ round
transition
90° elbow
11.5 Ft.
6″ Round,
90° elbow
8 Ft.
x (
)
6″ Round,
45° elbow
6.5 Ft.
x (
)
x (
x (
x (
x (
Subtotal column 1
)
)
)
)
=
DUCT
PIECES
Ft.
EQUIVALENT NUMBER
LENGTH
x USED
= TOTAL
6″ Round
wall cap
with
damper
34 Ft.
(6 ft. w/o
damper)
x (
)
=
Ft.
x (
)
=
Ft.
6″ Round
roof cap
30 Ft.
x (
)
=
Ft.
6″ Round
to
31⁄4″ x 10″
rect.
transition
5.5 Ft.
x (
)
=
Ft.
6″ Round
to
31⁄4″ x 10″
rect.
transition
90° elbow
14.5 Ft.
x (
)
=
Ft.
7″ Round,
90° elbow
8 Ft.
x (
)
=
Ft.
7″ Round,
45° elbow
6.5 Ft.
x (
)
=
Ft.
7″ Round
wall cap
with
damper
34 Ft.
(6 ft. w/o
damper)
x (
)
=
Ft.
x (
)
=
Ft.
Ft.
7″ Round
roof cap
30 Ft.
x (
)
=
Ft.
5.5 Ft.
x (
)
=
Ft.
=
Ft.
7″ Round
to
31⁄4″ x 10″
rect.
transition
x (
)
=
Ft.
Ft.
=
Ft.
7″ Round
to
31⁄4″ x 10″
rect.
transition,
90° elbow
14.5 Ft.
=
Subtotal column 2
=
Ft.
Subtotal column 1
=
Ft.
Total ductwork
=
Ft.
=
=
=
Ft.
Ft.
MAXIMUM DUCT LENGTH: For satisfactory air
movement, the total duct length of a 31⁄4″ x 10″
rectangular, 6″ or 7″ diameter round duct should
not exceed 65 equivalent feet.
8
Installation Instructions
DAMAGE – SHIPMENT/INSTALLATION
TOOLS YOU WILL NEED
• If the unit is damaged in shipment, return the unit to the
store in which it was bought for repair or replacement.
• If the unit is damaged by the customer, repair or
replacement is the responsibility of the customer.
• If the unit is damaged by the installer (if other than
the customer), repair or replacement must be made
by arrangement between customer and installer.
Flat blade and Phillips
screwdrivers
Saw (saber or keyhole)
MOUNTING SPACE
30″ or 36″
Bottom edge of
cabinet needs
to be 30″ or
more from
the cooking
surface
Pencil
Duct tape
Electric drill
Metal snips
(in some
applications)
1/4″ pivoting
hex socket
Pliers
Tape measure
Wire stripper
Flashlight
Caulking
Level
1/4″ Nutdriver
30″
min.
PARTS INCLUDED
66″ or more
from the floor
to the top of
the hood
PART
NOTES:
• This range hood is for installation over ranges or
cooktops up to 36″ wide.
• If you are going to vent your range hood to the
outside, see the “Ducting Requirements” section
for exhaust duct preparation.
9
QUANTITY
Grease Filter only (JV338)
1
Charcoal Filter only
(JN327 and RN328)
1
Grease Filter and Charcoal
Filter (JV347 and JV367)
2
Mounting Screws
4
Exhaust Adaptor
(for 31⁄4″ x 10″ rect. venting)
1
Exhaust Adaptor Screw
1
Installation Instructions
1 CHOOSE VENT OPTION
Determine the vent option that your installation will
require and that is available for your model from the
below choices.
A
IMPORTANT: If the hood is to be installed in a
recirculating, non-vented ductless manner, do not
knock out any vent openings in the hood. Only an
electrical access hole will be knocked out of the hood.
Outside top exhaust
(Vertical duct–31⁄4″ x 10″ Rectangular)
C
JV338
JV338
JV347
JV367
JV347
JV367
B
Outside rear exhaust
(Horizontal duct–31⁄4″ x 10″
Rectangular)
Outside top exhaust
(Vertical duct–7″ Round)
D
Recirculating
(non-vented/ductless)
JV338
JN327
RN328
JV347
JV367
JV347
JV367
10
Installation Instructions
5 REMOVE WIRING COVER
2 REMOVE EXHAUST ADAPTOR
If exhausting/venting using the 3 ⁄ ″ x 10″ rectangular
duct—optional for JV338, JV347 and JV367 models
only:
Remove the exhaust adaptor from the inside of the
hood. Set it aside along with its mounting screws.
Remove the wiring cover from inside the hood.
Set the cover and its mounting screw aside.
14
Wiring
cover
31⁄4″ x 10″
rectangular
exhaust
adaptor
and screws
3 REMOVE FILTER
Remove the shipping tape holding the metal grease
filter in place. Pull down on the center of the front
edge of the filter. The filter will then slip out of the
retaining tabs on the back.
6 REMOVE WIRING KNOCKOUT
Remove either the top or the back wiring knockout as
needed and install an approved strain relief clamp.
Back knockout
Top knockout
Strain relief
clamp
Metal grease filter
4 REVERSE THE BAFFLE FOR
DUCTED INSTALLATIONS ONLY
(JV347 and JV367 models)
If the hood is to be recirculated, skip to the next step.
Remove the baffle from the top of the hood. Re-install
the baffle so the short side marked “VENTED” is
visible. The long side of the baffle should be inside
the hood.
“VENTED” is visible
11
Strain relief
clamp
Installation Instructions
8 FOR 31⁄4″ X 10″ RECTANGULAR
7 REMOVE DUCT KNOCKOUT
DUCTED DISCHARGE
INSTALLATIONS ONLY:
If recirculating, non-vented ductless (JN327 and RN328,
and optional for JV347 and JV367 models only), skip to
Step 10 D and proceed.
Using a flat blade screwdriver, remove the appropriate
duct knockout from the top or back of the hood.
31⁄4″ x 10″ Rectangular
vertical discharge.
Remove top rectangular
duct knockout only.
Attach exhaust adaptor/damper over the appropriate
knockout opening (for vertical or horizontal,
depending on installation) with two exhaust adaptor
screws. Make sure damper pivot is nearest to top/back
edge of hood. Remove tape from damper flap.
7″ Round vertical
discharge. Remove circular
duct knockout only.
Up to 1″ side-toside adjustment
Pivot
(depending on
installation)
31⁄4″ x 10″ Rectangular
horizontal discharge. Remove
rear rectangular duct knockout only.
Exhaust adaptor/damper
(vertical discharge position)
Tape
Top/back edge
Exhaust adaptor/damper
(horizontal discharge position)
NOTE: The exhaust adaptor/damper can be installed
up to 1 inch on either side of the hood center to
accommodate off-center ductwork. In extreme offcenter installations, one end of the duct connector may
need to be trimmed to clear the electrical cable clamp.
9 FOR 7″ ROUND VERTICAL
DUCTED DISCHARGE
INSTALLATIONS ONLY:
Bend up the duct alignment ears in preparation for
later attachment of the 7″ duct.
Attachment ear tabs
12
Installation Instructions
10 MARK HOLES
C. Outside rear exhaust
(Horizontal duct–31⁄4″ x 10″ Rectangular)
Select the vent option that your installation will
require and proceed to that section:
• Use the diagram or the hood as a template and
mark the locations on the cabinet for ductwork,
electrical wiring and keyhole screw slots.
A. Outside top exhaust
(Vertical duct–31⁄4″ x 10″ Rectangular)
• Use the diagram or the hood as a template and
mark the locations on the cabinet for ductwork,
electrical wiring and keyhole screw slots.
Wood shims (recessed-bottom cabinets only)
Cabinet front
⁄ ″ 11⁄4″
12
Hood mounting screws (4)
133⁄4″ (30″ hood)
163⁄4″ (36″ hood)
Cabinet front
33⁄4″
133⁄4″ (30″ hood)
163⁄4″ (36″ hood)
7⁄″
Cabinet Bottom
51⁄4″
51⁄4″
Cabinet
bottom
133⁄4″ (30″ hood)
163⁄4″ (36″ hood)
34
3⁄″
34
⁄″
Vertical duct
access hole
12
Wood shims (recessedCenter
bottom cabinets only)
95⁄8″
11⁄4″
13⁄8″
Electrical access hole
(in cabinet bottom)
Hood mounting screws (4)
Access
hole for 7″
round duct
133⁄4″ (30″ hood)
163⁄4″ (36″ hood)
Wood shims (recessedbottom cabinets only)
73⁄4″
8″ DIA.
HOLE
95⁄8″
11⁄4″
5⁄″
34
Center
line
Electrical access hole
(in wall)
• Use the hood as a template and mark the locations
on the cabinet for the electrical wiring and keyhole
screw slots.
• Since the hood is to be recirculated (not to be vented
outside), do not cut out any vent openings in the wall
or cabinet bottom.
• Use the diagram or the hood as a template and
mark the locations on the cabinet for ductwork,
electrical wiring and keyhole screw slots.
Cabinet
bottom
51⁄4″
73⁄4″
133⁄4″ (30″ hood)
163⁄4″ (36″ hood)
D. Recirculating (non-vented ductless–
JN327 and RN328, and optional on
JV347 and JV367 models only)
B.Outside top exhaust (Vertical duct–7″ Round)
Cabinet front
51⁄4″
Hood mounting screws (4) Center line
line
133⁄4″ (30″ hood)
163⁄4″ (36″ hood)
Horizontal duct
access hole
13⁄8″
Electrical access
hole (in cabinet bottom)
13
Installation Instructions
14 SCREW IN PARTWAY
11 FOR RECESSED-BOTTOM
Drive a mounting screw (from the hardware packet)
partway into each center of the narrow neck of the
keyhole slots marked on the cabinet bottom.
CABINETS ONLY
15 OPTIONAL POWER CORD
KIT JXHC1
An optional Power Cord Connection Kit, model
JXHC1, is available at extra cost from your GE
supplier for installation using a standard 3-prong,
grounded wall outlet. Follow the Installation
Instructions packed with the kit to connect the
power cord to the range hood.
Wood shims
• If the cabinets have front, side or back trim, make
2 wood shims the width of the trim and attach them
to the cabinet bottom recess on both sides. See Step
10 for marking locations.
CL
Cabinet
12 CUT HOLES
Cut holes at marked locations for duct and electrical
wiring. For the vertical duct, cut out 3/4″ extra
toward the front of the cabinet so you can move the
duct freely when installing the hood. It may also ease
installation by cutting the hole 10 1⁄2″ instead of 10″.
7⁄″
34
11⁄4″
3-prong
wall outlet
(if using cord
connection)
13⁄4″ dia. clearance hole
for optional power
supply location
NOTE: If using optional Power Cord Kit JXHC1,
feed the power cord through the hole in the top
cabinet while raising the hood. Loop any excess
length of cord and tie away with a suitable tape
or tie.
13 RUN WIRES
Run the electrical wires through the wall or
cabinet according to National Electrical Code
and applicable local codes.
NOTE: DO NOT turn the power on until
installation is complete.
16 FEED IN WIRES
Lift the hood into position and feed the house
wiring through the wiring knockout.
14
Installation Instructions
19 INSTALL LIGHT BULB
17 SECURE HOOD
NOTE: A light bulb is not shipped with the hood.
Obtain one locally. Purchase and install an ordinary
screw-base light bulb, not more than 60 watts.
Slide the hood back against the wall. Tighten
the mounting screws. Be sure the screw heads
are in the narrow neck of the keyhole slot.
Mounting
screw (4)
Keyhole (4)
NOTE: DO NOT PUSH ON FAN BLADE. Pushing
on the blade may cause it to interfere with other
hood parts.
20 FOLLOW ELECTRICAL CODE
Complete the electrical wiring according to
National Electrical Code and local codes.
NOTE: This hood must be permanently grounded.
Connect house wiring (120 VAC) to hood wiring.
18 CONNECT DUCTWORK TO
HOOD (Ducted installations only)
On 7″ round installations, attach the 7″ duct
with sheet metal screws through the holes in
the alignment ears.
7″ round duct
Attachment ear tabs
Use duct tape to make joints secure and air tight.
Duct tape
15
Installation Instructions
21 CONNECT WIRING
23 REPLACE FILTER
Connect house black to hood black wire, house
white to hood white wire and house ground under
green ground screw. Securely tighten the strain
relief clamp onto the house wiring.
Make sure fan blade turns freely and replace the
filter. NOTE: On model JV347, install the metal
grease filter if ducted or the charcoal filter if
recirculated.
Green ground screw
Metal grease filter or charcoal filter
WARNING: IMPROPER CONNECTION OF
ALUMINUM HOUSE WIRING TO THESE
COPPER LEADS CAN RESULT IN A SERIOUS
PROBLEM. USE ONLY CONNECTORS
DESIGNED FOR JOINING COPPER TO
ALUMINUM AND FOLLOW THE
MANUFACTURER’S RECOMMENDED
PROCEDURE CLOSELY.
The installation is complete. Turn on power at
service panel, and test for proper operation.
TROUBLESHOOTING CHECKLIST
If the hood seems to be operating at high speed when
the control is not set on high, or if ventilation seems
inadequate, check the following:
❏ Knockouts not removed from hood.
❏ Damper blade not opening.
❏ Reduced airflow because the duct is too small or
the duct length is too long.
❏ The duct is blocked.
❏ Undersized or restrictive wall or roof cap.
22 REPLACE WIRING COVER
If the hood seems to make excessive noise:
❏ Fan may be hitting the filter. Turn off the fan and
remove the filter. Bend the filter down slightly in the
center (into a dome shape) to allow fan clearance.
Reinstall and adjust as needed.
Wiring cover
The fan does not work but the lights do:
❏ Switch power off at the service panel and lock the
service disconnecting means to prevent power from
being switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a prominent warning device, such as a tag,
to the service panel.
❏ Check the wiring connections. See the CONNECT
WIRING section in these Installation Instructions.
16
Safety Instructions
Notes.
Operating Instructions
Installation Instructions
Consumer Support
17
Consumer Support
Installation Instructions
Operating Instructions
Safety Instructions
Notes.
18
All warranty service provided by our Factory Service Centers, or
an authorized Customer Care® technician. To schedule service,
on-line, 24 hours a day, visit us at www.GEAppliances.com, or
call 800.GE.CARES (800.432.2737).
Staple your receipt here.
Proof of the original purchase
date is needed to obtain service
under the warranty.
For The Period Of:
GE Will Replace:
One Year
From the date of the
original purchase
Any part of the range hood which fails due to a defect in materials or workmanship.
During this full one-year warranty, GE will also provide, free of charge, all labor and
in-home service to replace the defective part.
■ Service trips to your home to teach you how to use
the product.
■ Damage to the product caused by accident, fire, floods
or acts of God.
■ Improper installation, delivery or maintenance.
■ Incidental or consequential damage caused by possible
defects with this appliance.
■ Failure of the product if it is abused, misused, or
used for other than the intended purpose or used
commercially.
■ Damage after delivery.
■ Replacement of house fuses or resetting of circuit
breakers.
Operating Instructions
What GE Will Not Cover:
Safety Instructions
GE Range Hood Warranty.
This warranty is extended to the original purchaser and any succeeding owner for products purchased for home
use within the USA. In Alaska, the warranty excludes the cost of shipping or service calls to your home.
Warrantor: General Electric Company. Louisville, KY 40225
Installation Instructions
Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives
you specific legal rights, and you may also have other rights which vary from state to state. To know what your
legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.
Consumer Support
19
Consumer Support.
GE Appliances Website
www.GEAppliances.com
Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day,
any day of the year! For greater convenience and faster service, you can now download Owner’s Manuals,
order parts, catalogs, or even schedule service on-line. You can also “Ask Our Team of Experts™”
your questions, and so much more...
Schedule Service
www.GEAppliances.com
Expert GE repair service is only one step away from your door. Get on-line and schedule your service at
your convenience 24 hours any day of the year! Or call 800.GE.CARES (800.432.2737) during normal
business hours.
Real Life Design Studio
www.GEAppliances.com
GE supports the Universal Design concept—products, services and environments that can be used by
people of all ages, sizes and capabilities. We recognize the need to design for a wide range of physical and
mental abilities and impairments. For details of GE’s Universal Design applications, including kitchen
design ideas for people with disabilities, check out our Website today. For the hearing impaired, please call
800.TDD.GEAC (800.833.4322).
Extended Warranties
www.GEAppliances.com
Purchase a GE extended warranty and learn about special discounts that are available while your warranty
is still in effect. You can purchase it on-line anytime, or call 800.626.2224 during normal business hours.
GE Consumer Home Services will still be there after your warranty expires.
Parts and Accessories
www.GEAppliances.com
Individuals qualified to service their own appliances can have parts or accessories sent directly to their
homes (VISA, MasterCard and Discover cards are accepted). Order on-line today, 24 hours every day or
by phone at 800.626.2002 during normal business hours.
Instructions contained in this manual cover procedures to be performed by any user. Other servicing generally
should be referred to qualified service personnel. Caution must be exercised, since improper servicing may cause
unsafe operation.
Contact Us
www.GEAppliances.com
If you are not satisfied with the service you receive from GE, contact us on our Website with all the details
including your phone number, or write to: General Manager, Customer Relations
GE Appliances, Appliance Park
Louisville, KY 40225
Register Your Appliance
www.GEAppliances.com
Register your new appliance on-line—at your convenience! Timely product registration will allow for
enhanced communication and prompt service under the terms of your warranty, should the need arise.
You may also mail in the pre-printed registration card included in the packing material.
Printed in China
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement