GE DRSR483GD Gas Dryer

GE DRSR483GD Gas Dryer
GE Appliances
DRSR483GDCC/WW – GE® Super 7.0 Cu. Ft. Capacity Gas Dryer with Stainless Steel Drum
Dryer Dimensions (in inches)
23-1/2
28-1/4
*24-1/2" from the edge of the side panel to the front.
25-1/2" from front to edge of endcaps.
25-1/2*
27
Exhaust Options:
When viewed from the front of the unit, exhaust 3-way via rear, left and
bottom. Dryer is shipped exhausted to the rear. Alternate exhausting
knockouts are supplied.
Gas: An individual properly-grounded branch circuit, with a three-prong
grounding-type receptacle, protected by a 15 or 20 amp circuit breaker or
a time-delay fuse is required.
8-1/2
36
42
2-1/2
Side View
Gas Dryer Electric Rating: 120V, 60Hz, 6A
11-1/2
2
Gas (BTU/HR): 22,000. Factory-equipped for natural gas. Tested for LP
gas. LP gas supply requires a conversion kit. Check installation instructions
for correct kit and have a qualified gas technician install a conversion kit.
See dryer ducting information for proper installation.
3-1/2
Rear View
Note: Dryer wall outlet must be located within 36" of service cord entry
and accessible when dryer is mounted in position.
Installation Information: For complete information, see installation
instructions packed with your dryer.
Power Cord Locations
5''
Power
Cord Hole
R
4-1/2''
Back View
Specification Created 6/03
Listed by
Underwriters
Laboratories
For answers to your Monogram,® GE Profile™ or
GE® appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center® service, 800.626.2000.
GE Appliances
DRSR483GDCC/WW – GE® Super 7.0 Cu. Ft. Capacity Gas Dryer with Stainless Steel Drum
Dryer Exhausting Information – Use Metal Duct Only
Vertical and Horizontal Ducting
For complete information, see installation instructions packed with your dryer.
Best Performance
A
A
4
B
Domestic
Dryer Models
2-1/2
7.3 Capacity Electric
and Gas Dryers
7.0 and 6.0
Capacity Models
all Electric Dryers
7.0 and 6.0
Capacity Models
all Gas Dryers
5.7 Capacity Electric
and Gas Dryers
Number
of
90°
Turns
0
1
2
3
4
0
1
2
3
4
0
1
2
3
0
1
2
3
4
Maximum Length of 4"
Dia. Rigid Metal Duct
Exhaust Hood Type
Maximum Length of 4"
Dia. Flexible Metal Duct
Exhaust Hood Type
A
4" Opening
B
2-1/2"
Opening
A
4" Opening
150 ft.
140 ft.
130 ft.
120 ft.
110 ft.
90 ft.
60 ft.
45 ft.
35 ft.
25 ft.
90 ft.
60 ft.
45 ft.
35 ft.
60 ft.
52 ft.
44 ft.
32 ft.
28 ft.
127 ft.
117 ft.
107 ft.
97 ft.
87 ft.
60 ft.
45 ft.
35 ft.
25 ft.
15 ft.
60 ft.
45 ft.
35 ft.
25 ft.
48 ft.
40 ft.
32 ft.
24 ft.
16 ft.
75 ft.
65 ft.
55 ft.
45 ft.
35 ft.
55 ft.
40 ft.
30 ft.
20 ft.
15 ft.
55 ft.
40 ft.
30 ft.
20 ft.
30 ft.
22 ft.
14 ft.
—
—
B
2-1/2"
Opening
52 ft.
42 ft.
32 ft.
22 ft.
12 ft.
45 ft.
30 ft.
20 ft.
15 ft.
10 ft.
45 ft.
30 ft.
20 ft.
15 ft.
18 ft.
14 ft.
10 ft.
—
—
Special Installation Requirements
Alcove or Closet Installation:
• If your dryer is approved for installation in an alcove or closet, it will be stated on a label on the dryer back.
• The dryer MUST be exhausted to the outside.
• Minimum clearances between dryer cabinet and adjacent walls or other surfaces are:
0" either side
3" front and rear
• Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 52”.
• Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq. in. of
open area equally distributed. If this closet contains both a washer and a dryer, doors must contain
a minimum of 120 sq. in. of open area equally distributed.
• No other fuel-burning appliance shall be installed in the same closet with a gas dryer.
Bathroom or Bedroom Installation:
• The dryer MUST be exhausted to the outdoors.
• The installation must conform with the local codes, or in the absence of local codes, with the
National Fuel Gas Code, ANSI Z223.
Minimum Clearances other than Alcove or Closet Installation:
• Minimum clearances to combustible surfaces
0" both sides
3" rear
Specification Created 6/03
Ducting Materials:
For best performance, this dryer should be vented with 4” diameter all-rigid metal exhaust duct. If “all-rigid
metal” duct cannot be used, then “flexible all-metal” venting can be used, but it will reduce the maximum
recommended duct length.
Exhaust Length Calculation:
1. Determine the number of 90° turns needed for your installation. If you exhaust to the side or bottom of dryer,
add one turn.
2. The maximum length of 4" rigid (aluminum or galvanized) duct which can be tolerated is shown in the table.
The maximum length for flexible ducts are less than for rigid duct.
2. A turn of 45° or less may be ignored. Two 45° turns within the duct length should be treated as a 90° elbow.
A turn over 45° should be treated as a 90° elbow.
Exhausting the dryer to the outside is strongly recommended to prevent large amounts of moisture and lint
from being blown into the room. Gas dryers or any dryer located in a closet must be exhausted to the outside.
Caution: For personal safety do not terminate exhaust into a chimney, under any enclosed house floor (crawl
space), or into an attic, since the accumulated lint could create a fire hazard or moisture could cause damage.
Never terminate the exhaust into a common duct or plenum with a kitchen exhaust, since the combination of lint
and grease could create a fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird nesting, etc. The wall cap
must also be located at least 12" above the ground or any other obstruction with the opening pointed down.
Other terminations, such as louvered wall boxes, are acceptable provided they are equivalent to a 4" opening
dampered wall cap.
For more information on venting kits and accessories, please call 1-800-GE CARES.
R
Listed by
Underwriters
Laboratories
For answers to your Monogram,® GE Profile™ or
GE® appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center® service, 800.626.2000.
GE Appliances
DRSR483GDCC/WW – GE® Super 7.0 Cu. Ft. Capacity Gas Dryer with Stainless Steel Drum
8 Cl
oth e s
Care Cycle
MORE DRY
COTTONS
OFF
COOL DOWN
WRINKLE
CARE
ON
OFF
REG. HEAT
EASY CARE
AUTOMATIC
WRINKLE FREE
PERM. PRESS
DELICATES
OPTIMUM DRY
MEDIUM
MED. HEAT
LESS DRY
LESS DRY
Extended Cool
4 Heat Settings
EASY CARE
START
Features and Benefits
s - Super Capacit
y
WRINKLE CARE
SIGNAL
WRINKLEAirCARE
Tumble
FABRIC CARE
START
LOUD
COTTONS
AUTOMATIC
MORE DRY
TIMED DRY
80
QUICK FLUFF 10
DELICATES
FLUFF
LOW HEAT
NO HEAT
DEWRINKLE 20
DAMP DRY 30
MIN
• Stainless Steel drum – It resists rust and won’t chip, peel or snag clothes.
70
40
50
60
• Auto Dry – Uses thermostats to monitor air temperature and reduce fabric wear.
• Four heat selections – Provide the right temperature for the right drying results.
• Wrinkle Care Extended Tumble – Continues to tumble clothes without heat to help prevent
wrinkling and creasing.
• Interior Dryer Light – Lets you see everything inside for easy loading and unloading.
• Eight dry cycles – A variety of fast flexible options for drying clothes.
• Variable end-of-cycle signal – Adjustable volume offers added flexibility.
• Quiet-by-Design™ – Engineered for quiet operation.
• Reverse-A-Door – Offers added installation flexibility.
• Upfront Lint Filter – Easy to reach and clean.
• Model DRSR483GDWW – White on white
• Model DRSR483GDCC – Bisque on bisque
Specification Created 6/03
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement