GE Profile DPSB619ED Electric Dryer

GE Profile DPSB619ED Electric Dryer
TM
DPSB619EDCC/WW – GE Profile™ Super 7.0 Cu. Ft. Capacity Electric Dryer with Stainless Steel Drum
23-1/2
28-1/4
*24-1/2" from the edge of the side panel to the front.
25-1/2" from front to edge of endcaps.
25-1/2*
8-1/2
42
2-1/2
Side View
NEMA Receptacle codes:
3-prong dryer cord/30A/4' long (cat #WX9X2) is for NEMA10-30R
receptacle
4-prong dryer cord/30A/4' long (cat #WX9X18) is for NEMA14-30R
receptacle
27
36
Circuit Requirements:
An individual, properly-grounded branch circuit, protected by a 30-amp
circuit breaker or a time-delay fuse, is required.
11-1/2
2
Exhaust Options:
4-way via rear, right, left and bottom.
Electric Dryer Rating:
240V, 5600W, 24A, 60Hz
208V, 4400W, 22A, 60Hz
3-1/2
Rear View
Note:
Dryer wall outlet must be located within 36" of service cord entry and
accessible when dryer is mounted in position.
Installation Information:
For complete information, see installation instructions packed with your dryer.
Power Cord Locations
5''
Power
Cord Hole
R
4-1/2''
Back View
Specification Revised 3/04
270186
Listed by
Underwriters
Laboratories
For answers to your Monogram,® GE Profile™ or
GE® appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center® service, 800.626.2000.
TM
DPSB619EDCC/WW – GE Profile™ Super 7.0 Cu. Ft. Capacity Electric Dryer with Stainless Steel Drum
For complete information, see installation instructions packed with your dryer.
Dryer Exhausting Information – Use Metal Duct Only
Vertical and Horizontal Ducting
Best Performance
Maximum Length of 4"
Dia. Rigid Metal Duct
Exhaust Hood Type
Maximum Length of 4"
Dia. Flexible Metal Duct
Exhaust Hood Type
Number
of
90°
Turns
A
4" Opening
B
2-1/2"
Opening
A
4" Opening
0
1
2
3
4
0
1
2
3
4
0
1
2
3
0
1
2
3
4
150 ft.
140 ft.
130 ft.
120 ft.
110 ft.
90 ft.
60 ft.
45 ft.
35 ft.
25 ft.
90 ft.
60 ft.
45 ft.
35 ft.
60 ft.
52 ft.
44 ft.
32 ft.
28 ft.
127 ft.
117 ft.
107 ft.
97 ft.
87 ft.
60 ft.
45 ft.
35 ft.
25 ft.
15 ft.
60 ft.
45 ft.
35 ft.
25 ft.
48 ft.
40 ft.
32 ft.
24 ft.
16 ft.
75 ft.
65 ft.
55 ft.
45 ft.
35 ft.
55 ft.
40 ft.
30 ft.
20 ft.
15 ft.
55 ft.
40 ft.
30 ft.
20 ft.
30 ft.
22 ft.
14 ft.
—
—
A
A
4
B
Domestic
Dryer Models
2-1/2
7.3 Capacity Electric
and Gas Dryers
7.0 and 6.0
Capacity Models
all Electric Dryers
7.0 and 6.0
Capacity Models
all Gas Dryers
5.7 Capacity Electric
and Gas Dryers
B
2-1/2"
Opening
52 ft.
42 ft.
32 ft.
22 ft.
12 ft.
45 ft.
30 ft.
20 ft.
15 ft.
10 ft.
45 ft.
30 ft.
20 ft.
15 ft.
18 ft.
14 ft.
10 ft.
—
—
Special Installation Requirements
Alcove or Closet Installation:
• If your dryer is approved for installation in an alcove or closet, it will be stated on a label on the dryer back.
• The dryer MUST be exhausted to the outside.
• Minimum clearances between dryer cabinet and adjacent walls or other surfaces are:
0" either side
3" front and rear
• Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 52”.
• Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq. in. of
open area equally distributed. If this closet contains both a washer and a dryer, doors must contain
a minimum of 120 sq. in. of open area equally distributed.
• No other fuel-burning appliance shall be installed in the same closet with a gas dryer.
Bathroom or Bedroom Installation:
• The dryer MUST be exhausted to the outdoors.
• The installation must conform with the local codes, or in the absence of local codes, with the
National Fuel Gas Code, ANSI Z223.
Minimum Clearances other than Alcove or Closet Installation:
• Minimum clearances to combustible surfaces
0" both sides
3" rear
Specification Revised 3/04
270186
Ducting Materials:
For best performance, this dryer should be vented with 4" diameter all-rigid metal exhaust duct. If
“all-rigid metal” duct cannot be used, then “flexible all-metal” venting can be used, but it will reduce
the maximum recommended duct length.
Exhaust Length Calculation:
1. Determine the number of 90° turns needed for your installation. If you exhaust to the side or
bottom of dryer, add one turn.
2. The maximum length of 4" rigid (aluminum or galvanized) duct which can be tolerated is shown
in the table. The maximum length for flexible ducts are less than for rigid duct.
A turn of 45° or less may be ignored. Two 45° turns within the duct length should be treated as a
90° elbow. A turn over 45° should be treated as a 90° elbow.
Exhausting the dryer to the outside is strongly recommended to prevent large amounts of
moisture and lint from being blown into the room. Gas dryers or any dryer located in a closet must be
exhausted to the outside.
Caution: For personal safety do not terminate exhaust into a chimney, under any enclosed house
floor (crawl space), or into an attic, since the accumulated lint could create a fire hazard or moisture
could cause damage. Never terminate the exhaust into a common duct or plenum with a kitchen
exhaust, since the combination of lint and grease could create a fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird nesting, etc.
The wall cap must also be located at least 12" above the ground or any other obstruction with the
opening pointed down.
Other terminations, such as louvered wall boxes, are acceptable provided they are equivalent to a
4" opening dampered wall cap.
For more information on venting kits and accessories, please call 1-800-GE-CARES.
R
Listed by
Underwriters
Laboratories
For answers to your Monogram,® GE Profile™ or
GE® appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center® service, 800.626.2000.
TM
DPSB619EDCC/WW – GE Profile™ Super 7.0 Cu. Ft. Capacity Electric Dryer with Stainless Steel Drum
Features and Benefits
Sensor Dry Cycles
DRYNESS
TIMED DRY
OPTIONS
HEAT LEVEL
START
SIGNAL
COTTONS
MORE
DRY
KNITS
SWEATERS
DRY
MIXED
LOADS
EASY CARE
PERM PRESS
DELICATES
SPEED
DRY
WARM
DE
UP
WRINKLE
LESS
DRY
CUSTOM CUSTOM
1
Sensor Dry Plus
2
DAMP
TIMED DRY
30 MIN
EXTEND
TUMBLE
HIGH
MEDIUM
LOW
AIR
DRY
ANTIBACTERIAL
DAMP
SIGNAL
DELAY
1-8 hrs.
MORE
STOP
LESS
EXTRA
LOW
EXTENDED TUMBLE
PAUSE
EST. TIME REMAINING
CLEAN LINT FILTER
SENSING
• Sensor Dry Plus – Continually monitors moisture levels to help clothes look better than ever,
longer than ever.
• Full electronic controls with Adaptive Logic System™ and LED readout – Simplify cycle
selections and provide accurate cycle times.
• Speed Dry – Delivers ready-to-go results in minutes.
• Five heat selections – Temperatures are matched to fabric type for better fabric care.
• Interior Dryer Light – Lets you see everything inside for easy loading and unloading.
• Multiple dry cycles, including custom options – Cycles are matched to fabric type for
enhanced drying performance and flexibility.
• Luxury Quiet performance – Minimizes operating noise.
• Variable End-of-Cycle signal – Adjustable volume offers added flexibility.
• Delay Start – Lets you do the laundry on your items.
• Deluxe dryer rack – Allows tumble-free drying of items like sneakers and stuffed animals.
• Model DPSB619EDWW – White on white
• Model DPSB619EDCC – Bisque on bisque
Specification Revised 3/04
270186
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement