Enterasys WPIM, APIM network module Instructions
Below you will find brief information for network module WPIM, network module APIM. These instructions guide you through the installation process of the WPIM and APIM modules, which are crucial for expanding the functionality and connectivity of your network system. These modules provide a seamless way to add new features and capabilities to your existing network infrastructure.
advertisement
CAUTION CAUTION
Failure to remove a BRIM or HSIM faceplate, as applicable, before installing this module may result in bent connector pins.
Follow the instructions on the back side of this card and consult your BRIM or HSIM documentation before installing this module.
P/N 9031498-02
Failure to remove a BRIM or HSIM faceplate, as applicable, before installing this module may result in bent connector pins.
Follow the instructions on the back side of this card and consult your BRIM or HSIM documentation before installing this module.
P/N 9031498-02
CAUTION CAUTION
Failure to remove a BRIM or HSIM faceplate, as applicable, before installing this module may result in bent connector pins.
Follow the instructions on the back side of this card and consult your BRIM or HSIM documentation before installing this module.
P/N 9031498-02
Failure to remove a BRIM or HSIM faceplate, as applicable, before installing this module may result in bent connector pins.
Follow the instructions on the back side of this card and consult your BRIM or HSIM documentation before installing this module.
P/N 9031498-02
INSTALLING WPIMs/APIMs
1. Attach the disposable grounding strap to your wrist.
2. See figure and remove two faceplate screws from the
BRIM (three screws from an HSIM, not shown in figure).
3. Remove the faceplate.
4. Insert the connector pins of the WPIM (same procedure for
APIM, not shown) into the connector on the BRIM.
WPIM CONNECTOR
STANDOFF
BRIM CONNECTOR
INSTALLING WPIMs/APIMs
1. Attach the disposable grounding strap to your wrist.
2. See figure and remove two faceplate screws from the
BRIM (three screws from an HSIM, not shown in figure).
3. Remove the faceplate.
4. Insert the connector pins of the WPIM (same procedure for
APIM, not shown) into the connector on the BRIM.
WPIM CONNECTOR
STANDOFF
BRIM CONNECTOR
WPIM 1
XMT
BRIM-W6
RCV
STS
XMT
STS
RCV
BRIM
WPIM 2
FACEPLATE SCREWS 1498_01
5. Press down evenly and firmly on the WPIM until the pins slide all the way into the connector holes. Ensure that the
WPIM seats flush on the standoffs.
6. Secure the WPIM using screws provided with the WPIM.
7. Attach the faceplate using the faceplate screws.
WPIM 1
XMT
BRIM-W6
RCV
STS
XMT
STS
RCV
BRIM
WPIM 2
FACEPLATE SCREWS 1498_01
5. Press down evenly and firmly on the WPIM until the pins slide all the way into the connector holes. Ensure that the
WPIM seats flush on the standoffs.
6. Secure the WPIM using screws provided with the WPIM.
7. Attach the faceplate using the faceplate screws.
INSTALLING WPIMs/APIMs
1. Attach the disposable grounding strap to your wrist.
2. See figure and remove two faceplate screws from the
BRIM (three screws from an HSIM, not shown in figure).
3. Remove the faceplate.
4. Insert the connector pins of the WPIM (same procedure for
APIM, not shown) into the connector on the BRIM.
WPIM CONNECTOR
STANDOFF
BRIM CONNECTOR
INSTALLING WPIMs/APIMs
1. Attach the disposable grounding strap to your wrist.
2. See figure and remove two faceplate screws from the
BRIM (three screws from an HSIM, not shown in figure).
3. Remove the faceplate.
4. Insert the connector pins of the WPIM (same procedure for
APIM, not shown) into the connector on the BRIM.
WPIM CONNECTOR
STANDOFF
BRIM CONNECTOR
WPIM 1
XMT
BRIM-W6
RCV
STS
XMT
STS
RCV
BRIM
WPIM 2
FACEPLATE SCREWS 1498_01
5. Press down evenly and firmly on the WPIM until the pins slide all the way into the connector holes. Ensure that the
WPIM seats flush on the standoffs.
6. Secure the WPIM using screws provided with the WPIM.
7. Attach the faceplate using the faceplate screws.
WPIM 1
XMT
BRIM-W6
RCV
STS
XMT
STS
RCV
BRIM
WPIM 2
FACEPLATE SCREWS 1498_01
5. Press down evenly and firmly on the WPIM until the pins slide all the way into the connector holes. Ensure that the
WPIM seats flush on the standoffs.
6. Secure the WPIM using screws provided with the WPIM.
7. Attach the faceplate using the faceplate screws.
advertisement
Key Features
- Easy installation
- Connects to BRIM/HSIM
- Expands network features
- Secure connection
Frequently Answers and Questions
How do I install a WPIM/APIM module?
What should I do if the connector pins bend during installation?
Can I install the module without attaching a grounding strap?
What is the purpose of the standoffs?
Where can I find the faceplate screws?
Related manuals
advertisement