Sony CMT-NE5 CD Shelf System

Sony CMT-NE5 CD Shelf System
4-253-397-11(6)
Micro Hi-Fi
Component
System
Operating Instructions
Owner’s Record
The model and serial numbers are located on the rear of the unit. Record the serial number
in the space provided below. Refer to them whenever you call upon your Sony dealer
regarding this product.
Model No. ______________
Serial No. ______________
CMT-NE5
CMT-NE3
©2004 Sony Corporation
WARNING
WARNING
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
To prevent fire, do not cover the ventilation of the
apparatus with news papers, table-cloths, curtains, etc.
And don’t place lighted candles on the apparatus.
To prevent fire or shock hazard, do not place objects
filled with liquids, such as vases, on the apparatus.
Do not install the appliance in a confined space,
such as a bookcase or built-in cabinet.
This appliance is
classified as a CLASS 1
LASER product. This
marking is located on the
rear exterior.
Don’t throw away the battery with
general house waste, dispose of it
correctly as chemical waste.
For customers in the United States
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and
receiver.
– Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV
technician for help.
CAUTION
You are cautioned that any changes or modification not
expressly approved in this manual could void your
authority to operate this equipment.
Note to CATV system installer:
This symbol is intended to alert
the user to the presence of
uninsulated “dangerous voltage”
within the product’s enclosure
that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
This symbol is intended to alert
the user to the presence of
important operating and
maintenance (servicing)
instructions in the literature
accompanying the appliance.
CAUTION
The use of optical instruments with this product will
increase eye hazard.
2GB
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building, as
close to the point of cable entry as practical.
For customers in Canada
CAUTION
TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
CAUTION
The use of optical instruments with this product will
increase eye hazard.
Except for European model
ENERGY STAR® is a U.S. registered
mark. As an ENERGY STAR® partner,
Sony Corporation has determined that
this product meets the ENERGY
STAR® guidelines for energy
efficiency.
Table of Contents
How to use this manual........................... 4
Playable discs.......................................... 4
Getting Started
Hooking up the system............................ 6
Setting the clock...................................... 8
CD/MP3 – Play
Loading a disc ......................................... 9
Playing a disc .......................................... 9
— Normal Play/Shuffle Play
Playing repeatedly................................. 10
— Repeat Play
Creating your own program .................. 11
— Program Play
Tuner
Presetting radio stations ........................ 12
Listening to the radio ............................ 13
— Preset Tuning
— Manual Tuning
Using the Radio Data System (RDS).... 14
(European model CMT-NE5 only)
Tape – Play
Loading a tape....................................... 15
Playing a tape ........................................ 15
Timer
Falling asleep to music ......................... 17
— Sleep Timer
Waking up to music.............................. 18
— Play Timer
Timer recording radio programs........... 19
— Rec Timer
Display
Turning off the display ......................... 20
— Power Saving Mode
Viewing information about the disc in the
display ............................................ 20
Optional Components
Hooking up optional components......... 21
Troubleshooting
Problems and remedies......................... 22
Messages............................................... 24
Additional Information
Precautions............................................ 26
Specifications........................................ 27
List of button locations and reference
pages............................................... 30
Tape – Recording
Recording your favorite CD tracks on a
tape.................................................. 16
— CD-TAPE Synchro Recording
Recording on a tape manually............... 16
— Manual Recording
Sound Adjustment
Adjusting the sound ..............................17
3GB
How to use this manual
• The instructions in this manual are for model
CMT-NE5 and CMT-NE3. Check your
model number by looking at the front panel.
In this manual, CMT-NE5 is used for
illustration purposes unless stated otherwise.
Any difference in operation is clearly
indicated in the text, for example, “CMT-NE5
only”.
• This manual mainly explains operations using
the remote, but the same operations can also
be performed using the buttons on the system
having the same or similar names.
Playable discs
You can play back the following discs on this
system. Other discs cannot be played back.
List of playable discs
Format of discs
Audio CDs
CD-R/CD-RW
(audio data/MP3 files*)
* CMT-NE5 only.
4GB
Disc logo
Discs that this system cannot
play
• CD-ROMs
• CD-Rs/CD-RWs other than those recorded in
the following formats:
– music CD format
– MP3 format that conforms to ISO96601)
Level 1/Level 2, Joliet or Multi Session2)
• A disc that has a non-standard shape (e.g.,
card, heart).
• A disc with paper or stickers on it.
• A disc that has the adhesive, cellophane tape,
or a sticker still left on it.
1) ISO 9660 Format
The most common international standard for the
logical format of files and folders on a CD-ROM.
There are several specification levels. In Level 1,
file names must be in the 8.3 format (no more than
eight characters in the name, no more than three
characters in the extension “.MP3”) and in capital
letters. Folder names can be no longer than eight
characters. There can be no more than eight nested
folder levels. Level 2 specifications allow file
names and folder names up to 31 characters long.
Each folder can have up to 8 trees.
For Joliet in the expansion format (file and folder
names can have up to 16 characters) make sure of
the contents of the writing software, etc.
2) Multi Session
This is a recording method that enables you to add
data using the Track-At-Once method.
Conventional CDs begin at a CD control area called
the Lead-in and end at an area called Lead-out. A
Multi Session CD is a CD having multiple sessions,
with each segment from Lead-in to Lead-out
regarded as a single session. This unit supports up to
10 sessions.
CD-Extra: This format records audio (audio CD
data) on the tracks in session 1 and data on the tracks
in session 2. This unit supports up to 10 sessions.
Mixed CD: This format records data on the first
track and audio (audio CD data) on the second and
subsequent tracks of a session.
Notes on CD-R and CD-RW
• Some CD-Rs or CD-RWs cannot be played
on this system depending upon the recording
quality or physical condition of the disc, or
the characteristics of the recording device.
Furthermore, the disc will not play if it has not
been correctly finalized. For more
information, see the operating instructions for
the recording device.
• Discs recorded on CD-R/CD-RW drives may
not be played back because of scratches, dirt,
recording condition or the driver’s
characteristics.
• CD-R and CD-RW discs recorded in Multi
Session that have not ended by “closing the
session” are not supported.
• The system may be unable to play MP3
format files that do not have the extension
“.MP3”.
• Attempting to play non-MP3 format files that
have the extension “.MP3” may result in noise
or malfunction.
• With formats other than ISO 9660 level 1 and
2, folder names or file names may not be
displayed correctly.
• The following discs take a longer time to start
playback.
– a disc recorded with complicated tree
structure.
– a disc recorded in Multi Session.
– a disc to which data can be added (nonfinalized disc).
Music discs encoded with
copyright protection
technologies
This product is designed to playback discs that
conform to the Compact Disc (CD) standard.
Recently, various music discs encoded with
copyright protection technologies are marketed
by some record companies. Please be aware that
among those discs, there are some that do not
conform to the CD standard and may not be
playable by this product.
Cautions when playing a disc
that is recorded in Multi
Session
• If the disc begins with a CD-DA session, it is
recognized as a CD-DA (audio) disc, and
MP3 sessions are played back without sound.
• If the disc begins with an MP3 session, it is
recognized as an MP3 disc, and CD-DA
sessions are played back without sound.
• The playback range of an MP3 disc is
determined by the tree structure of files
produced by analyzing of the disc.
• A disc with a mixed CD format will be
recognized as a CD-DA (audio) disc.
5GB
Getting Started
Hooking up the system
Perform the following procedures 1 to 4 to hook up your system using the supplied cords and
accessories.
Right speaker
Left speaker
1
2
43
FM lead antenna
AM loop antenna
1 Connect the speakers.
Connect the right and left speaker cords to
the SPEAKER terminals as shown below.
2 Connect the FM and AM antennas.
Set up the AM loop antenna, then connect
it.
Gray (3)
L
#
Black (#)
Plug type A
AM loop antenna
#
R
Insert this portion
3
AM
SPEA
KER
IMPE
D
USE ANCE
6-16
ANTE
NNA
Extend the FM lead
antenna horizontally
6GB
FM 75
COAX
IAL
4 Connect the power cord to a wall
outlet.
Plug type B
AM loop antenna
AM
ANTE
NNA
FM 75
COAX
IAL
Extend the FM lead
antenna horizontally
Inserting two R6 (size AA)
batteries into the remote
Getting Started
If the plug does not fit the wall socket,
detach the supplied plug adaptor (only for
models equipped with an adaptor).
To turn on the system, press ?/1.
Plug type C
AM loop antenna
AM
ANTE
NNA
Extend the FM lead
antenna horizontally
FM 75
COAX
IAL
Note
If you do not use the remote for a long period of time,
remove the batteries to avoid possible damage from
battery leakage and corrosion.
Tip
When the remote no longer operates the system,
replace both batteries with new ones.
North American models:
Connect using the white side
Other models:
Connect using the brown side
Note
To prevent noise pickup, keep the antennas away from
the system and other components.
3 For models with a voltage selector, set
VOLTAGE SELECTOR to the local
power line voltage. The voltage
selector is located at the bottom of the
apparatus.
Refer to the print on your system’s
VOLTAGE SELECTOR for available
settings
*
* Saudi Arabian model: 120 – 127 V
7GB
Setting the clock
Use buttons on the remote for the operation.
1
2
3
4
5
6
Press ?/1 to turn on the system.
Press CLOCK/TIMER SET.
Press ./> repeatedly to set the
hour.
Press ENTER.
Press ./> repeatedly to set the
minute.
Press ENTER.
The clock starts working.
To adjust the clock
1
2
3
Press CLOCK/TIMER SET.
Press ./> until “CLOCK” appears,
then press ENTER.
Do the same procedures as step 3 to 6
above.
Note
The clock is not displayed in Power Saving Mode
(page 20).
8GB
CD/MP3 – Play
Loading a disc
2
Press Z PUSH OPEN/CLOSE on the
unit.
Place a disc with the label side up on
the CD compartment.
— Normal Play/Shuffle Play
You can play audio CDs and discs with MP3
audio tracks.
MP3 audio tracks cannot be played on CMTNE3.
Track number
1
2
3
Press Z PUSH OPEN/CLOSE on the
unit again to close the lid of the CD
compartment.
Notes
• Do not use a disc with tape, seals or paste on it as this
may cause malfunction.
• Keep the lens on the CD player clean and do not
touch it. If you do so, the lens may be damaged and
the CD player will not operate properly.
CD/MP3 – Play
1
Playing a disc
Playing time
Press CD to switch the function to CD.
Press PLAY MODE in stop mode
repeatedly until the mode you want
appears.
Select
To play
No display
(Normal Play)
The tracks on the disc in
original order.
ALBM*
(Normal Play)
All MP3 audio tracks in the
album on the disc in original
order.
When playing a non-MP3
disc, Album Play performs
the same operation as
Normal Play.
SHUF(FLE)
(Shuffle Play)
All tracks on the disc in
random order.
ALBM SHUF*
(Shuffle Play)
All MP3 audio tracks in the
album on the disc in random
order.
When playing a non-MP3
disc, Album Shuffle Play
performs the same operation
as Shuffle Play.
PGM
(Program Play)
The tracks on the disc in the
order you want them to be
played (see “Creating your
own program” on page 11).
* CMT-NE5 only.
3
Press N.
continued
9GB
Other operations
To
Do this
Stop play
Press x.
Pause
Press X (or CD/NX on the unit).
Press again to resume play.
Select a track
Press ./> repeatedly.
Select an album
of MP3*
Press ALBUM +/– repeatedly
after step 2.
Find a point in a
track
Keep pressing m/M during
playback and release it at the
desired point.
Remove a disc
Press Z PUSH OPEN/CLOSE on
the unit.
— Repeat Play
You can play all the tracks or a single track on a
disc repeatedly.
MP3 audio tracks cannot be played on CMTNE3.
Press REPEAT on the remote repeatedly
during playback until “REP(EAT)” or
“REP(EAT) 1” appears.
* CMT-NE5 only.
REP(EAT): For all the tracks on the disc up to
five times.
REP(EAT) 1: For a single track only.
Notes
To cancel Repeat Play
• You cannot change the play mode during playback.
• Some time may be needed to start playback of discs
recorded in complex configurations such as many
layers.
• When the disc is inserted, the player reads all the
audio tracks on that disc. If there are many albums or
non-MP3 audio tracks on the disc, it may take a long
time for play to begin or for the next MP3 audio track
to start play.
• Do not save unnecessary albums or audio tracks
other than MP3 ones in the disc to be used for MP3
listening. We recommend that you do not save other
types of audio tracks or unnecessary albums on a disc
that has MP3 audio tracks.
• An album that does not include an MP3 audio track
is skipped.
• Maximum album number: 150 (including root
album)
• The maximum number of MP3 audio tracks that can
be contained on a single disc is 255.
• Playback is possible up to 8 levels.
• MP3 audio tracks are played back in the order that
they are recorded on the disc.
• Depending on the encoding/writing software,
recording device, or the recording media used at the
time an MP3 audio track is recorded, you may
encounter such problems as disabled playback,
sound interruptions and noise.
• When playing back an MP3 audio track, the playback
elapsed time indication may differ from the actual
time in the following cases.
– When you play back a VBR (variable bit rate)
MP3 audio track
– When you perform Fast Forward or Rewind
(Manual Search)
10GB
Playing repeatedly
Press REPEAT repeatedly until both
“REP(EAT)” and “REP(EAT) 1” disappear.
Note
When you select “REP(EAT) 1”, that track is repeated
endlessly until “REP(EAT) 1” is canceled.
Creating your own
program
Other operations
Do this
Cancel Program
Play
Press PLAY MODE in stop
mode repeatedly until both
“PGM” and “SHUF(FLE)”
disappears.
Erase the program
Press CLEAR in stop mode.
Each time you press the button, a
track is cleared from the end of
the program.
— Program Play
You can make a program of up to 25 steps.
You can synchro record the programed tracks
onto a cassette tape (page 16).
MP3 audio tracks cannot be played on CMTNE3.
1
2
3
Press CD to switch the function to CD.
Press PLAY MODE in stop mode
repeatedly until “PGM” appears.
Press ./> repeatedly until the
desired track number appears.
Selected track number
Add a track to the Perform steps 3 and 4 in stop
end of the program mode.
CD/MP3 – Play
To
Tips
• The program you made remains after Program Play
finishes. To play the same program again, press N
(or CD/NX on the unit). However, the program is
cleared when you open the CD compartment.
• “– –.– –” appears if the total program time exceeds
100 minutes, if you select a track whose number is 21
or over, or when you programed an MP3 audio track.
Total playing time
(including selected
track)
For CMT-NE5 only:
When programing an MP3, press ALBUM
+/– repeatedly to select the album, then
press ./> repeatedly until the
desired track number appears.
4
Press ENTER on the remote.
The track is programed.
The program step number appears,
followed by the last programed track
number and total playing time.
5
6
To program additional tracks, repeat
steps 3 and 4.
Press N.
Program Play starts.
11GB
Tip
Press x to stop scanning.
Tuner
Presetting radio stations
You can preset up to 20 FM stations and 10 AM
stations. You can then tune in any of those
stations simply by selecting the corresponding
preset number.
Manual tuning preset
You can manually tune in and store the radio
frequency of the desired stations.
1
2
Automatic tuning preset
You can automatically tune in all of the stations
that can be received in your area and then store
the radio frequency of the desired stations.
3
1
4
5
2
3
Press TUNER/BAND repeatedly to
select “FM” or “AM”.
Press TUNING MODE repeatedly until
“AUTO” appears in the display.
Press +/– (or TUNING +/– on the unit).
12GB
Press TUNER MEMORY.
Press +/– (or TUNING +/– on the unit)
repeatedly to select the desired preset
number.
Press ENTER.
Do this
If “TUNED” does not appear and the
scanning does not stop
Tune in a station
with a weak signal
Follow the procedure described
in “Manual tuning preset”
(page 12).
Set another station
to the existing
preset number
After step 4, press +/– (or
TUNING +/– on the unit)
repeatedly to select the preset
number you want to store the
station.
Press TUNER MEMORY.
Preset number
6
7
Press +/– (or TUNING +/– on the unit)
repeatedly to tune in the desired
station.
To
A preset number flashes. Perform steps 5
and 6 while the preset number flashes.
5
Press TUNING MODE on the unit
repeatedly until “AUTO” and
“PRESET” disappear from the display.
The frequency changes as the system scans
for a station. Scanning stops automatically
when a station is tuned in. At that time,
“TUNED” and “STEREO” (for stereo
program only) appear.
Set the frequency of the desired radio
station as described in steps 2 and 3 of
“Manual tuning preset” (page 12).
4
6
7
Press TUNER/BAND repeatedly to
select “FM” or “AM”.
Press +/– (or TUNING +/– on the unit)
repeatedly to select the desired preset
number.
Press ENTER.
Repeat steps 3 through 6 to preset
other stations.
Repeat steps 3 through 6 to preset
other stations.
Other Operations
To change the AM tuning interval
(except for European model and
Saudi Arabian model)
Note
You cannot change the setting in Power Saving Mode.
Tips
• The preset stations are retained for about half a day
even if you disconnect the power cord or if a power
failure occurs.
• To improve the reception, adjust the supplied
antennas or connect an external antenna.
You can listen to a radio station either by
selecting a preset station, or by manually tuning
in the station.
Listening to a preset station
— Preset Tuning
Tuner
The AM tuning interval is factory-preset to
9 kHz (or 10 kHz for some areas). To change the
AM tuning interval, tune in any AM station first,
then turn off the power by pressing ?/1. While
holding TUNING +, press ?/1. When you
change the interval, all the AM preset stations
are initialized. To reset the interval, repeat the
same procedure.
Listening to the radio
Preset radio stations in the tuner’s memory first
(see “Presetting radio stations” on page 12).
1
2
3
Press TUNER/BAND repeatedly to
select “FM” or “AM”.
Press TUNING MODE repeatedly until
“PRESET” appears in the display.
Press +/– (or TUNING +/– on the unit)
repeatedly to select the desired preset
station.
Listening to non-preset radio
station
— Manual Tuning
1
2
3
Press TUNER/BAND repeatedly to
select “FM” or “AM”.
Press TUNING MODE repeatedly until
“AUTO” and “PRESET” disappear from
the display.
Press +/– (or TUNING +/– on the unit)
repeatedly to tune in the desired
station.
continued
13GB
Tips
• To improve broadcast reception, adjust the supplied
antennas, or connect a commercially available
external antenna.
• When an FM stereo program has static noise, press
FM MODE until “MONO” appears. There will be no
stereo effect, but the reception will improve.
• Press TUNING MODE repeatedly until “AUTO”
appears in step 2 above, then press +/– (or TUNING
+/– on the unit). The frequency indication changes
and scanning stops when the system tunes in a station
(Automatic Tuning).
• To record the radio programs, use manual recording
(page 16).
• You can change the display into the clock display
(for 8 seconds) by pressing DISPLAY.
Using the Radio Data
System (RDS)
(European model CMT-NE5 only)
What is the Radio Data
System?
Radio Data System (RDS) is a broadcasting
service that allows radio stations to send
additional information along with the regular
program signal. This tuner offers convenient
RDS features like station name. RDS is
available only on FM stations.*
Note
RDS may not work properly if the station you are tuned
in is not transmitting the RDS signal properly or if the
signal is weak.
* Not all FM stations provide RDS service, nor do they
provide the same types of services. If you are not
familiar with the RDS system, check with your local
radio stations for details on RDS services in your
area.
Receiving RDS broadcasts
Simply select a station from the FM band.
When you tune in a station that provides RDS
services, the station name appears in the display.
To check the RDS information
Each time you press DISPLAY, the display
changes cyclically as follows:
Station name* t Frequency t Clock display
* If the RDS broadcast is not properly received, the
station name may not appear in the display.
14GB
Tape – Play
Loading a tape
1
2
Playing a tape
You can use TYPE I (normal).
1
Press Z PUSH OPEN on the unit.
Load a recorded/recordable tape into
the cassette holder.
Press N (or TAPE/N on the unit).
Other operations
To
Do this
Stop play
Press x.
Pause
Press X. Press again to resume
play.
Fast-forward or
rewind
Press m/M.
Remove a tape
Press Z PUSH OPEN on the unit
in stop mode.
Tape – Play
With the side
you want to
play/record
facing
forward.
2
Press TAPE to switch the function to
TAPE.
15GB
Tape – Recording
Recording your favorite
CD tracks on a tape
— CD-TAPE Synchro Recording
You can record a whole CD on a tape.
You can use TYPE I (normal).
Use buttons on the unit for the operation.
1
2
Load a recordable tape.
Press CD SYNCHRO.
“SYNC” and “REC” appear.
The tape deck stands by for recording and
the CD player pauses for playback.
4
You can record just the portions you like from a
CD on a tape. You can also record a radio
program.
Use buttons on the unit for the operation.
1
2
To stop recording
Press x.
To record a disc by specifying
track order
You can record only your favorite CD tracks
using Program Play. Between steps 2 and 3,
perform steps 1 to 4 of “Creating your own
program” (page 11).
Load a recordable tape.
Select the desired source to record.
• TUNER: To record from this system’s
tuner.
• CD: To record from this system’s CD
player.
• MD: To record from the optional
component connected to the MD jacks.
3
Press z REC PAUSE/START.
“REC” appears and the tape deck stands by
for recording.
4
Press z REC PAUSE/START.
Recording starts.
When the recording is completed, the CD
player and the tape deck stop automatically.
16GB
— Manual Recording
Load a CD you want to record.
For CMT-NE5 only:
When you want to record an album from an
MP3 disc, be sure to press PLAY MODE to
select ALBM, then use ALBUM +/– to
select the desired album before proceeding.
3
Recording on a tape
manually
Press z REC PAUSE/START, then start
playing the desired source to record.
Recording starts.
Other operations
To
Do this
Stop recording
Press x.
Pause recording
Press z REC PAUSE/START.
Tip
For recording from a CD, you can press ./> to
select tracks during recording pause mode (after step 3
and before step 4).
Sound Adjustment
Timer
Adjusting the sound
Falling asleep to music
You can adjust the bass and treble to enjoy more
powerful sound.
Generating a more dynamic
sound (Dynamic Sound
Generator X-tra)
To cancel the DSGX, press DSGX on the unit
again.
You can set the system to turn off after a certain
time, so that you can fall asleep to music.
Use buttons on the remote for the operation.
Press SLEEP repeatedly.
Each time you press the button, the minute
display (the turn-off time) changes cyclically as
follows:
AUTO* t 90MIN t 80MIN t … t
10MIN t OFF
Adjusting the bass and treble
* The system automatically turns off in 100 minutes or
after the current CD or tape finishes playing.
You can adjust the bass and treble.
Other operations
1
Press EQ (or BASS/TREBLE on the
unit) repeatedly to select “BASS” or
“TREBLE”.
To
Each time you press the button, the display
changes cyclically as follows:
BASS y TREBLE
Change the time
to turn off
SLEEP repeatedly to select the
time you want.
Cancel Sleep
Timer function
SLEEP repeatedly until “OFF”
appears.
2
Press ./> (or TUNING +/– on the
unit) repeatedly to adjust the level
while “BASS” or “TREBLE” appears.
Press
Check the
SLEEP once.
remaining time**
** You cannot check the remaining time if you select
“AUTO”.
Tape – Recording/Sound Adjustment/Timer
Press DSGX on the unit.
— Sleep Timer
Note
Do not set to “AUTO” during Synchro Recording on a
tape.
Tip
You can use Sleep Timer, even if you have not set the
clock.
17GB
Waking up to music
To
Do this
Cancel the timer/
activate the timer/
check the setting
1 Press CLOCK/TIMER
Prepare the sound source you want to
play.
Change the setting
Start over from step 1.
• CD: Load a disc. To start from a specific
track, make a program (see “Creating
your own program” on page 11).
• TAPE: Load a tape (see “Playing a tape”
on page 15).
• TUNER: Tune in a radio station (see
“Listening to the radio” on page 13).
Notes
— Play Timer
You can wake up to music at a preset time. Make
sure you have set the clock (see “Setting the
clock” on page 8).
Use buttons on the remote for the operation.
1
2
3
4
Adjust the volume.
Press CLOCK/TIMER SET.
Press ./> repeatedly until
“PLAY” appears, then press ENTER.
“ON TIME” appears and the hour
indication flashes.
5
Set the time to start playing.
Press ./> repeatedly to set the hour,
then press ENTER.
The minute indication flashes.
Press ./> repeatedly to set the
minute, then press ENTER.
6
7
Set the time to stop playing following
the same procedure as step 5.
Press ./> repeatedly until the
desired sound source appears.
Each time you press the button, the display
changes cyclically as follows:
t TUNER y CD T
t TAPE T
8
Press ENTER.
The start time, the stop time and the sound
source, then the original display returns.
9
18GB
Other operations
Press ?/1 to turn off the system.
SELECT and “SELECT”
appears.
2 Press ./> repeatedly
until “PLAY”, “REC” or
“(TIMER) OFF” appears,
then press ENTER.
• If you use Play Timer and Sleep Timer at the same
time, Sleep Timer has priority.
• Do not operate the system from the time the system
turns on until the play starts (about 15 seconds before
the preset time).
• If the system is on about 15 seconds before the preset
time, Play Timer will not be activated.
• You cannot use the optional component connected to
the MD jacks as sound sources for Play Timer.
• You cannot activate Play Timer and Rec Timer at the
same time.
Timer recording radio
programs
— Rec Timer
To timer record, you must first preset the radio
station (see “Presetting radio stations” on
page 12) and set the clock (see “Setting the
clock” on page 8).
Use buttons on the remote for the operation.
1
Press CLOCK/TIMER SET.
Press ./> repeatedly until “REC”
appears, then press ENTER.
Set the time to start recording.
Press ./> repeatedly to set the hour,
then press ENTER.
The minute indication flashes.
Press ./> repeatedly to set the
minute, then press ENTER.
5
Do this
Cancel the timer/
activate the timer/
check the setting
1 Press CLOCK/TIMER
Change the setting
Start over from step 1.
SELECT and “SELECT”
appears.
2 Press ./> repeatedly
until “PLAY”, “REC” or
“(TIMER) OFF” appears,
then press ENTER.
Notes
Tune in the preset radio station (see
“Listening to a preset station” on
page 13).
“ON TIME” appears and the hour
indication flashes.
4
To
• If you use Rec Timer and Sleep Timer at the same
time, Sleep Timer has priority.
• Do not operate the system from the time the system
turns on until the recording starts (about 15 seconds
before the preset time).
• If the system is on about 15 seconds before the preset
time, Rec Timer will not be activated.
• The volume is reduced to minimum during
recording.
• You cannot activate Play Timer and Rec Timer at the
same time.
• After you have set Rec Timer, do not operate the
system until the recording ends.
Timer
2
3
Other operations
Set the time to stop recording following
the same procedure as step 4.
Rec Timer settings and the desired station
appear, then the original display returns.
6
7
Load a recordable tape.
Press ?/1 to turn off the system.
19GB
Display
Turning off the display
Viewing information
about the disc in the
display
— Power Saving Mode
The clock display can be turned off to minimize
the amount of power consumed during standby
(Power Saving Mode).
Press DISPLAY repeatedly while the
system is off until the clock display
disappears.
To cancel Power Saving Mode
Press DISPLAY while the system is off. Each
time you press the button, the display switches
as follows:
Clock display* y No display (Power Saving
Mode)
* The clock is displayed only if you set the clock.
Tips
• The ?/1 indicator lights up even in Power Saving
Mode.
• The timer continues to operate in Power Saving
Mode.
Note
You cannot perform the following operations in Power
Saving Mode.
– setting the clock
– changing the AM tuning interval
You can check the playing time and remaining
time of the current track or that of the disc.
When a disc with MP3 audio tracks is loaded,
you can also check the information recorded on
disc, such as the titles.
Checking the remaining time
and titles (CD/MP3)
Press DISPLAY repeatedly during Normal
Play.
Each time you press the button, the display
changes cyclically as follows:
Current track number and elapsed playing time
t Current track number and remaining time or
“– –.– –”* t Remaining time of the disc or
“– –.– –”* t Track title (disc with MP3 audio
tracks** only) t Album name* t Clock
display
* “– –.– –” appears when you select a CD track whose
number is 21 or over, or when you select an MP3
audio track (CMT-NE5 only).
** When you play back a track with an ID3 tag, the ID3
tag appears. The ID3 tag displays only the track title
information.
Checking the total playing
time and titles (CD/MP3)
Press DISPLAY repeatedly in stop mode.
Each time you press the button, the display
changes cyclically as follows:
TOC display* or total number of albums on the
disc** or total track number of the current
album** t Album name** t Clock display
* TOC = Table of Contents; displays current disc
number, total number of tracks on the disc and total
playing time of the disc.
** For discs with MP3 audio tracks, album titles may
not be displayed depending on the play mode
(CMT-NE5 only).
20GB
Optional Components
Hooking up optional components
To enhance your system, you can connect optional components. Refer to the operating instructions
provided with each component.
Optional analog component
A MD jacks
Use audio cords (not supplied) to connect an
optional analog component (MD deck, etc.) to
these jacks. You can then listen to the sound
from the component.
Listening to audio from a
connected component
1
Connect audio cords.
See the illustration above.
2
Press FUNCTION repeatedly until “MD”
appears.
Start playing the connected component.
Display/Optional Components
From the audio output
jacks of an optional
analog component
Recording audio from a
connected component
1
2
Connect audio cords.
Start recording manually.
See “Recording on a tape manually” on
page 16.
21GB
Troubleshooting
Problems and remedies
Should you encounter a problem with your
system, do the following:
The timer cannot be set.
• Set the clock again (page 8).
1
Make sure the power cord and speaker
cords are correctly and firmly connected.
2
Find your problem in the troubleshooting
checklist below and take the indicated
corrective action.
The timer does not function.
• Press CLOCK/TIMER SELECT on the remote to
set the timer and light up “c PLAY” or “c REC”
in the display (pages 18 and 19).
• Check the timer setting and set the correct time
(pages 18 and 19).
• Cancel the Sleep Timer function (page 17).
• Make sure the clock is correctly set.
If the problem persists after doing all of the
above, consult your nearest Sony dealer.
When the ?/1 indicator flashes
Immediately unplug the power cord and
check the following items.
• If your system has a voltage selector, is the
voltage selector set to the correct voltage?
• Check the voltage for your region, then
make sure the voltage selector is set
correctly.
Check all the above items and fix any
problems found. After ?/1 indicator stops
flashing, reconnect the power cord and turn
on the system. If the indicator still flashes, or
if the cause of the problem cannot be found
even after checking all the above items,
consult your nearest Sony dealer.
General
“– –:– –” appears in the display.
• A power interruption has occurred. Set the clock
(page 8).
There is no sound.
• Press VOLUME + on the remote repeatedly (or
turn VOLUME on the unit clockwise).
• Make sure the headphones are not connected.
• Check the speaker connections (page 6).
Sound comes from one channel, or
unbalanced left and right volume.
• Place the speakers as symmetrically as possible.
• Connect the supplied speakers.
22GB
There is severe hum or noise.
• Move the system away from the source of noise.
• Connect the system to a different wall outlet.
• Install a noise filter (commercially available) to
the power line.
The color on the TV screen is irregular.
• Move the speakers farther away from the TV set.
The remote does not function.
• Remove the obstacle.
• Move the remote closer to the system.
• Point the remote at the system’s sensor.
• Replace the batteries (R6/size AA).
• Locate the system away from the fluorescent light.
Speakers
Sound comes from one channel, or the left
and right volumes are unbalanced.
• Check the speaker connections and placement.
CD/MP3 player
The sound drops out.
• The lens is dirty. Clean it with a commercially
available blower.
Play does not start.
• Eject the disc and check whether a disc is loaded.
• Wipe the disc clean (page 26).
• Replace the disc.
• Load the disc that this system can play (page 4).
• Load the disc correctly.
• Load the disc with the label side up.
• Remove the disc and wipe away the moisture on
the disc, then leave the system turned on for a few
hours until the moisture evaporates.
• Press N (or CD/NX on the unit) to start play.
The sound skips.
• Wipe the disc clean (page 26).
• Replace the disc.
• Try moving the system to a place without
vibration (e.g., on top of a stable stand).
• Try moving the speakers away from the system, or
placing them on separate stands. When you listen
to a track with bass sounds at high volume, the
speaker vibration may cause the sound to skip.
• Keep the antennas away from the system and
other components.
• Consult your nearest Sony dealer if the supplied
AM antenna has come off the plastic stand.
• Try turning off surrounding electrical equipment.
A stereo FM program cannot be received in
stereo.
• Press FM MODE until “STEREO” appears in the
display.
Play does not start from the first track.
• Press PLAY MODE repeatedly until both “PGM”
and “SHUF(FLE)” disappear to return to Normal
Play.
Tape deck
MP3 audio track cannot be played back (CMTNE5 only).
• CMT-NE3 does not play MP3 audio.
• Recording was not performed according to the
ISO 9660 level 1 or level 2 format, or Joliet in the
expansion format.
• The MP3 audio track does not have the extension
“.MP3”.
• The data is not stored in MP3 format.
• Discs containing tracks other than MPEG1, 2
Audio Layer-3 files cannot be played.
The tape does not erase completely.
• The record/playback heads are magnetized.
Demagnetize them (page 27).
The album title, track title and ID3 tag do not
appear correctly (CMT-NE5 only).
• Use a disc that conforms with ISO 9660 level 1,
level 2, or Joliet in the expansion format.
There is excessive wow or flutter, or the sound
drops out.
• The capstans in the tape deck are dirty. Clean
them using a cleaning cassette (page 27).
Noise increases or the high frequencies are
erased.
• The record/playback heads are magnetized.
Demagnetize them (page 27).
Troubleshooting
MP3 audio tracks take longer to play back than
others (CMT-NE5 only).
• After the system reads all tracks on the discs,
playback may take more time than usual if:
– the number of albums or tracks on the disc is
very large.
– the album and track organization structure is
very complex.
The tape does not record or play, or there is a
decrease in sound level.
• The heads are dirty. Clean them (page 27).
• The record/playback heads are magnetized.
Demagnetize them (page 27).
The tape does not record.
• No cassette is loaded. Load a cassette.
• The tab has been removed from the cassette.
Cover the broken tab with adhesive tape
(page 27).
• The tape has wound to the end.
Optional components
Tuner
Severe hum or noise/stations cannot be
received.
• Set the proper band and frequency (page 12).
• Connect the antenna properly (page 6).
• Find a place and an orientation that provide good
reception, then set up the antenna again. If you
cannot obtain good reception, we recommend you
connect a commercially available external
antenna.
• The supplied FM lead antenna receives signals
along its entire length, so make sure you extend it
fully.
There is no sound.
• Refer to General item “There is no sound.”
(page 22) and check the condition of the system.
• Connect the component properly (page 21) while
checking:
– if the cords are connected properly.
– if the cord plugs are firmly inserted all the way.
• Turn on the connected component.
• Refer to the operating instructions supplied with
the connected component and start playing.
• Press FUNCTION repeatedly until “MD” appears
(page 21).
continued
23GB
The sound is distorted.
• Set the volume of the connected component
lower.
Messages
One of the following messages may appear or
flash in the display during operation.
If the system still does not
operate properly after performing
the above measures, reset the
system as follows:
Use buttons on the unit for the operation.
1
2
3
4
Disconnect the power cord.
CD/MP3
NO DISC
There is no disc in the player.
NO STEP
All of the programed tracks have been erased.
Press ?/1 to turn on the system.
OVER
You have reached the end of the disc while pressing
and holding M during playback or pause.
Press x, ?/1 and turn volume to the left at
the same time.
FULL
You tried to program 26 or more tracks (steps).
Reconnect the power cord.
The system is reset to the factory settings. You
should set the settings you made, such as the
preset stations, clock, and timer.
PUSH STOP
You pressed PLAY MODE during playback.
Tuner
COMPLETE
The preset operation ended normally.
Tape
NO TAB
You cannot record the tape because the tab has been
removed from the cassette.
NO TAPE
There is no tape in the tape deck.
Timer
SET CLOCK
You tried to select the timer with the clock not set.
PUSH SELECT
You tried to set the clock or timer during timer
operation.
SET TIMER
You tried to select the timer when Play Timer or Rec
Timer are not set.
TIME NG
Play Timer or Rec Timer start and end times are set
to the same time.
24GB
Other
INVALID
You pressed an invalid button.
Troubleshooting
25GB
On operation
Additional Information
Precautions
On operating voltage
• Before operating the system, check that the operating
voltage of your system is identical with the voltage of
your local power supply.
• The voltage selector is located at the bottom of the
apparatus.
On safety
• The unit is not disconnected from the AC power
source (mains) as long as it is connected to the wall
outlet, even if the unit itself has been turned off.
• Unplug the system from the wall outlet (mains) if it
is not to be used for an extended period of time. To
disconnect the power cord (mains lead), pull it out by
the plug. Never pull the cord itself.
• Should any solid object or liquid fall into the system,
unplug the system and have it checked by qualified
personnel before operating it any further.
• AC power cord must be changed only at the qualified
service shop.
On placement
• Do not place the system in an inclined position.
• Do not place the system in locations where it is;
– Extremely hot or cold
– Dusty or dirty
– Very humid
– Subject to vibrations
– Subject to direct sunlight.
• Use caution when placing the unit or speakers on
surfaces that have been specially treated (with wax,
oil, polish, etc.) as staining or discoloration of the
surface may result.
On heat buildup
• Although the system heats up during operation, this
is not a malfunction.
• Place the system in a location with adequate
ventilation to prevent heat build-up in the system.
• If you continuously use this system at a high volume,
the cabinet temperature of the top, side and bottom
rises considerably. To avoid burning yourself, do not
touch the cabinet.
• To prevent a malfunction, do not cover the
ventilation hole.
26GB
• If the system is brought directly from a cold to a
warm location, or is placed in a very damp room,
moisture may condense on the lens inside the CD
player. Should this occur, the system will not operate
properly. Remove the disc and leave the system
turned on for about an hour until the moisture
evaporates.
• When you move the system, take out any disc.
If you have any questions or problems concerning your
system, please consult your nearest Sony dealer.
Notes on discs
• Before playing, clean the disc with a cleaning cloth.
Wipe the disc from the center out.
• Do not use solvents such as benzene, thinner,
commercially available cleaners or anti-static spray
intended for vinyl LPs.
• Do not expose the disc to direct sunlight or heat
sources such as hot air ducts, nor leave it in a car
parked in direct sunlight.
• Do not use discs encircled with a protection ring.
This may cause a malfunction to the system.
• When using discs that have glue or similar tacky
substance on the label side of the disc or that used a
special ink when the label was printed, there is a
chance that the disc or label may become attached to
parts inside this unit. When this occurs, it may not be
possible to remove the disc, and may also cause this
unit to malfunction. Be sure to check that the label
side of the disc is not sticky before using.
The following types of disc should not be used:
– Rental or used discs with attached seals where the
glue extends beyond the seal. The perimeter of the
seal on the disc is tacky.
– Discs that have labels printed using a special ink
that feels tacky when touched.
• Discs with non-standard shapes (e.g., heart, square,
star) cannot be played on this unit. Attempting to do
so may damage the unit. Do not use such discs.
Cleaning the cabinet
Clean the cabinet, panel and controls with a soft cloth
slightly moistened with mild detergent solution. Do not
use any type of abrasive pad, scouring powder or
solvent such as thinner, benzene or alcohol.
To save a tape permanently
To prevent a tape from being accidentally recorded
over, break off the cassette tab from side A or B as
illustrated.
Break off the
cassette tab
If you later want to reuse the tape for recording, cover
the broken tab with adhesive tape.
Before placing a cassette in the tape
deck
Take up any slack in the tape. Otherwise, the tape may
get entangled in the parts of the tape deck and become
damaged.
When using a tape longer than
90 minutes
Cleaning the tape heads
Clean the tape heads after every 10 hours of use. Be
sure to clean the tape heads before you start an
important recording or after playing an old tape. Use a
separately sold dry-type or wet-type cleaning cassette.
For details, refer to the instructions of the cleaning
cassette.
Demagnetizing the tape heads
Demagnetize the tape heads and the metal parts that
have contact with the tape after every 20 to 30 hours of
use with a separately sold demagnetizing cassette. For
details, refer to the instructions of the demagnetizing
cassette.
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
(The United States model only)
With 6 ohm loads, both channels driven, from
120-10,000 Hz; rated 13 watts per channel
minimum RMS power, with no more than 10%
total harmonic distortion from 250 milliwatts to
rated output.
Main unit
Amplifier section
CMT-NE3
North American model:
Continuous RMS power output (reference):
15 + 15 W
(6 ohms at 1 kHz, 10%
THD)
European model:
DIN power output (rated): 11 + 11 W (6 ohms at 1
kHz, DIN)
Continuous RMS power output (reference):
15 + 15W (6 ohms at 1
kHz, 10% THD)
Music power output (reference):
25 + 25 W
Other models:
The following measured at AC 230 V or AC 120 V, 50/
60 Hz
DIN power output (rated): 11 + 11 W
(6 ohms at 1 kHz, DIN)
Continuous RMS power output (reference):
15 + 15 W
(6 ohms at 1 kHz, 10%
THD)
Inputs
MD (phono jacks):
Outputs
PHONES:
SPEAKER:
Additional Information
The tape is very elastic. Do not change the tape
operations such as play, stop, and fast-winding
frequently. The tape may get entangled in the tape
deck.
Specifications
Sensitivity 450 mV,
impedance 47 kilohms
Accepts headphones with
an impedance of 8 ohms or
more
Accepts impedance of 6 to
16 ohms.
CMT-NE5
North American model:
Continuous RMS power output (reference):
20 + 20 W
continued
27GB
(6 ohms at 1 kHz, 10%
THD)
European model:
DIN power output (rated): 16 + 16 W (6 ohms at 1
kHz, DIN)
Continuous RMS power output (reference):
20 + 20 W (6 ohms at 1
kHz, 10% THD)
Music power output (reference):
33 + 33 W
Other models:
The following measured at AC 230 V or AC 120 V, 50/
60 Hz
DIN power output (rated): 16 + 16 W
(6 ohms at 1 kHz, DIN)
Continuous RMS power output (reference):
20 + 20 W
(6 ohms at 1 kHz, 10%
THD)
Inputs
MD (phono jacks):
Outputs
PHONES:
SPEAKER:
CMT-NE5
Recording system
Frequency response
Wow and flutter
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range
Antenna
Antenna terminals
Intermediate frequency
AM tuner section
Tuning range
Pan-American model:
Sensitivity 450 mV,
impedance 47 kilohms
Accepts headphones with
an impedance of 8 ohms or
more
Accepts impedance of 6 to
16 ohms.
European model:
Other models:
CD player section
CMT-NE3
Laser
Frequency response
CMT-NE5
Laser
Frequency response
Semiconductor laser
(λ=780 nm)
Emission duration:
continuous
20 Hz – 20 kHz
Wow and flutter
28GB
Antenna
Intermediate frequency
87.5 – 108.0 MHz
FM lead antenna
75 ohms unbalanced
10.7 MHz
530 – 1,710 kHz
(with the tuning interval
set at 10 kHz)
531 – 1,710 kHz
(with the tuning interval
set at 9 kHz)
531 – 1,602 kHz
(with the tuning interval
set at 9 kHz)
530 – 1,710 kHz
(with the tuning interval
set at 10 kHz)
531 – 1,602 kHz
(with the tuning interval
set at 9 kHz)
AM loop antenna, external
antenna terminal
450 kHz
Speaker
Semiconductor laser
(λ=780 nm)
Emission duration:
continuous
20 Hz – 20 kHz
Tape deck section
CMT-NE3
Recording system
Frequency response
4-track 2-channel, stereo
50 – 13,000 Hz (±3 dB),
using Sony TYPE I
cassettes
±0.15% W. Peak (IEC)
0.1% W. RMS (NAB)
±0.2% W. Peak (DIN)
4-track 2-channel, stereo
50 – 13,000 Hz (±3 dB),
using Sony TYPE I
cassettes
±0.15% W. Peak (IEC)
0.1% W. RMS (NAB)
±0.2% W. Peak (DIN)
CMT-NE3
Speaker system
Speaker units
Woofer:
Nominal impedance
Dimensions (w/h/d)
Mass
CMT-NE5
Speaker system
Speaker units
Woofer:
Tweeter:
Nominal impedance
Full Range Speaker
System
10 cm dia., cone type
6 ohms
Approx. 146 × 230.5 × 135
mm
Approx. 1.5 kg net per
speaker
2-way, bass-reflex type
10 cm dia., cone type
4 cm dia., cone type
6 ohms
Dimensions (w/h/d)
Mass
Approx. 152 × 230.5 × 160
mm
Approx. 1.7 kg net per
speaker
General
Power requirements
North American model:
Mexican model:
European model:
Australian model:
Korean model:
Chinese model:
Taiwanese model:
Argentine model
CMT-NE5:
CMT-NE3:
Saudi Arabian model:
Other models:
CMT-NE5
North American model:
Mexican model:
European model:
Korean model:
Chinese model
Taiwanese model:
Other models:
Dimensions (w/h/d)
Mass
CMT-NE3:
CMT-NE5:
Supplied accessories
220 V AC, 50/60 Hz
220 – 240 V AC, 50/60 Hz
120 – 127 V or 220 – 240V
AC, 50/60 Hz
110 – 120 V or 220 – 240 V
AC, 50/60 Hz
Adjustable with voltage
selector
45 W
50 W
50 W
57 W
0.3 W (in Power Saving
Mode)
58 W
58 W
50 W
65 W
Additional Information
Power consumption
CMT-NE3:
120 V AC, 60 Hz
120 V AC, 60 Hz
230 V AC, 50/60 Hz
230 – 240 V AC, 50/60 Hz
220 V AC, 60 Hz
220 V AC, 50/60 Hz
120 V AC, 50/60 Hz
Approx. 164 × 230.5 × 263
mm incl. projecting parts
and controls
Approx. 3.7 kg
Approx. 3.9 kg
Remote Commander (1)
R6 (size AA) batteries (2)
AM loop antenna (1)
FM lead antenna (1)
Design and specifications are subject to change
without notice.
29GB
List of button locations and reference pages
How to use this page
Use this page to find the location of buttons and other
parts of the system that are mentioned in the text.
Illustration number
r
DISPLAY 0 (14, 20)
R
Name of button/part
R
Reference page
Main unit
BUTTON DESCRIPTIONS
ALPHABETICAL ORDER
A–O
P–Z
ALBUM +/–* 7 (10, 11)
BASS/TREBLE 8 (17)
Cassette compartment qf
CD SYNCHRO qg (16)
DISPLAY 0 (14, 20)
Display window 5
DSGX 9 (17)
PHONES jack qk
PLAY MODE qj (9, 11)
Remote sensor 2
TUNER/BAND qs (12, 13)
TUNING +/– 4 (12, 13, 17)
TUNING MODE qj (12, 13)
VOLUME qa (18, 22)
1 2 34 5
?/1 (power) 1 (7, 18, 19, 24)
.m/M> (skip back/
skip forward, rewind/fast
forward) 4 (10, 11, 15, 17, 18,
19)
x (stop) 3 (10, 15, 16, 24)
z REC PAUSE/START qh (16)
CD/NX (play/pause) ql (9, 10,
22)
TAPE/N (play) w; (15)
Z PUSH OPEN/CLOSE (CD
open/close) 6 (9)
Z PUSH OPEN (tape open/close)
qd (15)
6
7*
8
9
0
qa
qs
w;
ql
qk
qj
qd
qf
qh qg
* Button available only on CMT-NE5.
30GB
Remote control
BUTTON DESCRIPTIONS
ALPHABETICAL ORDER
A–O
P–Z
ALBUM +/– qa (10, 11)
CD qh (9, 11, 16, 18)
CLEAR qd (11)
CLOCK/TIMER SELECT 2
(18, 19)
CLOCK/TIMER SET 3 (8, 18,
19)
DISPLAY ql (14, 20)
ENTER 9 (8, 11, 12, 18, 19)
EQ qs (17)
FM MODE 4 (13)
FUNCTION 6 (21)
PLAY MODE qk (9, 11)
REPEAT 4 (10)
SLEEP w; (17)
TAPE qg (15, 18)
TUNER/BAND 5 (12, 13, 18)
TUNER MEMORY qj (12)
TUNING MODE qk (12, 13)
VOLUME +/– 0 (18, 22)
CMT-NE5
CMT-NE3
w;
w;
1
2
3
4
5
6
7
ql
qk
qj
qh
qg
qf
qs
2
3
4
5
6
7
8
8
qd
1
Additional Information
ql
qk
qj
qh
qg
qf
?/1 (power) 1 (7, 18, 19, 24)
m/M (rewind/fast forward)
7 (10, 15)
./> (go back/go forward)
qf (8, 10, 11, 18, 19)
x (stop) 8 (10, 15, 16, 24)
X (pause) 8 (10, 15)
N (play) 8 (9, 11, 15, 22)
+/– (tuning) qf (12, 13)
9
qd
*
qs
9
*
0
0
qa
* Button does not function with this model.
31GB
Sony Corporation Printed in China
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement