VTech VT 1711 User's Manual
Add to my manuals4 Pages
VTech VT 1711 is a 900MHz digital spread spectrum cordless telephone with a one-line telephone cord, a wall mount accessory, a belt clip, and a rechargeable battery pack. It has a ringer equivalence number (REN) of 5.0000, allowing you to connect multiple devices to your telephone line. The battery pack can be recharged in 16 hours and provides a low-battery signal when it needs to be replaced. The phone also features a spare battery charger in the base unit. With its various accessories and features, the VTech VT 1711 is a versatile and convenient cordless telephone for home or office use.
advertisement
USER’S MANUAL
VT 1711
900MHZ DIGITAL SPREAD
SPECTRUM CORDLESS TELEPHONE
Parts Check List
1. Base unit, Handset and
AC adaptor
2. One-Line Telephone Cord
INTRODUCTION
3. Battery Pack
4. Wall mount accessory
5. Belt Clip
To purchase replacement battery packs, call VTECH Communications at 1-800-595-
9511. In Canada, call VTECH Electronics at 1-800-267-7377.
10
9
8
7
20
6
1
19
18
3
2
5
4
17
16
15
14
13
MEMOR
12
11
Y DIALING
CHARGING spare batter
PO
WER handset in-use y
DIGIT
SPREAD SPECTR
900
VT1711
MHZ
UM
PA
GE
Base Unit Handset
VTECH
Belt Clip
Wall mount accessory
Telephone Cord
VTECH COMMUNICATIONS LTD.
I M P O R TA N T
BEFORE USING YOUR NEW
PHONE, WE STRONGLY
RECOMMEN D YOU READ THIS
MANUAL THOROUGHLY.
This equipment complies with Parts 15 and
68 of the Federal Communications
Commission (FCC) rules for the United
States. It also complies with regulations RSS-
210 and CS-03 of Industry Canada (IC).
A label is located on the underside of the base unit containing both the FCC registration number and Ringer Equivalence Number (REN) or the IC registration number and Load Number.
You must, upon request, provide this information to your local telephone company.
This equipment is compatible with inductively coupled hearing aids.
FCC Part 15
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
The equipment has been tested and found to comply with part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:
* Reorientate or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet or on a circuit different from that to which the receiver is connected.
* Consult the dealer or an experienced radio/TV technician for help.
FCC AND IC REGULATIONS
FCC Part 68
The FCC requires that you connect your cordless telephone to the nationwide telephone network through a modular telephone jack (USOC RJ11C or RJ11W).
Your telephone company may discontinue your service if your equipment causes harm to the telephone network. They will notify you in advance of disconnection, if possible.
During notification, you will be informed of your right to file a complaint with the FCC.
If it is determined that your telephone equipment is malfunctioning, the FCC requires that it not be used and that it be unplugged from the modular jack until the problem has been corrected. Repairs to this telephone equipment can only be made by the manufacturer or its authorized agents or by others who may be authorized by the
FCC. For repair procedures, follow the instructions outlined under the VTECH
Limited Warranty.
The REN is useful in determining the number of devices you may connect to your telephone line and still enable the devices to ring when you receive a call. The general rule is that the REN value should not exceed
5.0 total; however, contact your local telephone company for the specific number in your area.
INDUSTRY CANADA (IC) NOTICE
NOTICE: The Industry Canada (IC) label identifies certified equipment. This certification means that the equipment meets telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal
Equipment Technical Requirements document(s). The department does not guarantee the equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable
2
Battery Pack
1
AC Adaptor
FCC AND IC REGULATIONS
method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by a user to this equipment, or equipment malfunctions, may give the telephone communications company cause to request the user to disconnect the equipment.
User should ensure for their own protection, that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.
Caution! User should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.
NOTICE: The Ringer Equivalence Number
(REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.0000.
IMPORTANT SAFETY INSTRUCTIONS
When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a dry cloth for cleaning.
4. Do not use this product near water, for example, near a bathtub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool.
5. Do not place this product on an unstable cart, stand, or table. The telephone may fall, causing serious damage to the telephone.
6. Slots and openings in the cabinet and the back or bottom are provided for ventilation, to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the product on the bed, sofa, rug, or other similar surface.
This product should never be placed near or over a radiator or heat register.
This product should not be placed in a built-in installation unless proper ventilation is provided.
7. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your dealer or local Power Company.
8. Do not allow anything to rest on the power cord. Do not locate this product where the cord will be abused by persons walking on it.
9. Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock.
10. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product.
3
IMPORTANT SAFETY INSTRUCTIONS
11. To reduce the risk of electric shock, do not disassemble this product. Opening or removing covers may expose you to dangerous voltages or other risks.
Incorrect reassembly can cause electric shock when the appliance is subsequently used.
12.Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a) When the power supply cord plug is damaged or frayed.
b) If liquid has been spilled into the product.
c ) If the product has been exposed to rain or water.
d) If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions because improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation.
e) If the product has been dropped or the cabinet has been damaged.
f) If the product exhibits a distinct change in performance.
13.Do not use the telephone to report a gas leak in the vicinity of the leak.
SAVE THESE INSTRUCTIONS
REPLACING THE HANDSET BATTERY PACK
Charging the handset batteries. The handset of your VTech VT 1711 cordless telephone is powered by a rechargeable battery pack. It charges automatically whenever the handset is in the base. You should charge the battery pack for 16 hours when you first receive your phone. You’ll know that battery pack needs charging when:
* The phone emits a warning tone when you press the ON/OFF key.
* The LOW BATT LED is slowly flashing
* The handset seems completely dead; no lights are evident, and pressing keys do not generate a beep.
To Charge the Battery Pack. To charge the battery pack, place the handset in the base unit. The CHARGE indicator will light to show the handset is seated properly and the battery pack is charging. It is recommended that the battery pack be charged for at least 16 hours initially and 8 hours for maintenance charging. You can use your telephone before that with diminished capacity, but it is best to charge the battery pack fully. It will take several recharge cycles to maximize the charge capacity of your battery pack. The maximum battery life between charges is 7 hours of continuous talk time or 14 days of stand by.
Alternatively, if you have purchased a spare battery pack and it has been charging in the base unit, simply exchange the drained handset battery pack with the fully charged replacement battery pack from the base charger. Place the drained handset battery pack into the base charger to recharge.
4
REPLACING THE HANDSET BATTERY PACK
ITS IMPOSSIBLE TO
OVERCHARGE THE BATTERY
PACK
The battery pack can be recharged many times, but if you get a low-battery signal even after 8 hours of maintenance charging in the base cradle (or 24 hours in the base spare battery charger), the battery pack(s) should be replaced.
To purchase replacement battery packs, call VTECH Communications at 1-800-
595-9511. In Canada, call VTECH
Electronics at 1-800-267-7377.
REPLACING THE HANDSET
BATTERY PACK
Follow the steps below:
1. Remove the battery case cover by pressing on the ridged lines and sliding downward.
2. Discard the old battery pack. Don’t put the old battery pack in a trash compactor or a fire - it could burst.
3. Place the new battery pack in the battery compartment with the metal contacts facing down.
4. Replace the battery case cover by sliding the cover upwards.
5. If the new battery pack is not already charged, place the handset in the cradle of the base unit to allow it to charge for 16 hours.
CAUTION:
To Reduce the Risk of Fire or Injury to
Persons, read and Follow the Instructions
1. Use only VTECH rechargeable battery pack.
2. Do not dispose of the battery in a fire.
The cell may explode.
IMPORTANT:
Do not dispose of this battery into household garbage. For information on recycling or proper disposal, consult your local solid waste collection or disposal organization.
3. Do not open or mutilate the battery.
Released electrolyte is corrosive and may cause damage to the eyes or skin.
It may be toxic if swallowed.
4. Exercise care in handling batteries in order not to short the battery with conducting materials such as rings, bracelets, and keys. The battery or conductor may overheat and cause burns.
A WORD ABOUT RECHARGEABLE
BATTERIES
Your Ni-Cd batter y pack recharges whenever the Handset is returned to the
Base Unit cradle. You may return the
Handset to its cradle whenever you’re not using the phone.
SPARE BATTERY CHARGER
The VT 1711 has a built-in Spare Battery
Charger, which is located in the cradle of the Base Unit.
NOTE: In order to benefit from this feature, you must obtain an optional
Spare Battery pack from an authorized VTech dealer, or by contacting VTech Customer Service at 1-800-595-9511
Installation
Remove the Spare Battery charger cover by pressing the release tab and lifting up.
Place a battery pack in the Spare Battery charger. Make sure the metal charging contacts on the underside of the battery pack are aligned with the charging contact in the Spare Battery charger.
Power Backup
When a Spare Battery pack is installed in the Base Unit, the VTech 1711 uses this battery to provide operational backup in case of a power failure. If you have a fully charged battery pack in the Spare Battery charger and there is a power outage, you will still be able to place and receive calls for up to four hours.
5
REPLACING THE HANDSET BATTERY PACK
Replacing a Drained Handset battery
The spare battery pack can also be used to replace a drained Handset battery pack to ensure interrupted use. Be sure to put the drained battery in the Spare Battery charger for recharging.
Please note that the Spare battery pack recharges at a slower rate than a battery pack charging in the Handset. It takes 24 hours to fully charge a battery pack in the
Spare Battery charger.
WALL MOUNTING
The Wall Mount adaptor is designed to fit on standard Wall Mount plates.
1. Choose a spot near an electrical outlet and a telephone jack.
Your phone requires a modular telephone jack and a standard electrical outlet (120v
AC). The power cord is six feet long; make sure there is an electrical outlet within reach of the base. The outlet should not be controlled by a wall switch. If the switch is ever turned off, the phone will not operate.
USING THE WALL MOUNT
ADAPTOR
1. Position the wall mount bracket on
the base. Line up the tabs on the wall mount adaptor with the holes on the bottom of the base. Snap the wall mount bracket firmly in place.
2. Mount the base on the wall.
Position the base so the mounting studs will fit into the holes on the bottom of the base. Position the power cord to extend down the wall the phone is to be mounted on. Slide the base down on the mounting studs until it locks into place.
3. Connect the telephone line cord.
The telephone line cord has a snap-in plug at each end. Insert one of the plugs into the jack on the bottom of the base.
Insert the other end of the plug into the wall jack.
4. Plug the AC adaptor into an electrical outlet and the DC connector on the back of the Base Unit.
GETTING STARTED
SETTING UP YOUR VTECH VT 1711
Choose an area near an electrical outlet and a telephone wall jack.
AC POWER ADAPTOR
Plug the AC power adaptor into an electrical outlet and the DC connector to the back of the base unit.
SETTING THE TONE/PULSE SWITCH
The TONE\PULSE switch is located on the bottom of the base unit and is factory set to TONE. If you have touch tone service, do not change the switch setting. If you have rotary (Pulse) service, set the switch to PULSE.
CHARGE THE HANDSET BATTERY
PACK BEFORE USE
The battery pack recharges automatically whenever the handset is in the base unit. The battery pack must be charged for 16 hours before using your phone for the first time.
CONNECT TELEPHONE LINE CORD
Plug one end of the telephone cord into a wall jack, and the other end into the back of the Base Unit.
6
CHECK FOR A DIAL TONE
After charging the battery pack, rotate the Base Unit antenna to an upright position.
Pick up the Handset, making sure the
Handset antenna is fully extended. Now press ON/OFF, you should hear a dial tone.
If not, see ‘IN CASE OF DIFFICULTY’.
Fill in the telephone number card on the base unit.
CAUTION:
1. Never install telephone wiring during a lightning storm.
2. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
3. Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.
4. Use caution when installing or modifying telephone lines.
7
BASIC OPERATION
ANSWERING CALLS
When the Handset is in the Base Unit cradle, simply pick up the Handset to answer an incoming call.
When the Handset is away from the Base
Unit press any key to answer an incoming call.
MAKING CALLS
1. Press the ON/OFF key and wait for a dial tone.
2. Then dial the number you want.
If you make a mistake when dialing, press
ON/OFF to hang up, then press the ON/
OFF key to get the dial tone again.
DISCONNECTING
To end a call, either place the handset back in the Base Unit, or press ON/OFF.
VOLUME CONTROLS
The volume controls for the handset are located on the side of the unit. Press the or key to increase or decrease the volume. While on an active call, holding either key down will continually change the volume setting. The earpiece volume level will change accordingly.
There are four volume levels.
flash
You can use your VTech VT1711 cordless phone with services such as Call
Waiting. Simply press the FLASH key.
REDIAL
To REDIAL the last number you dialed, press the ON/OFF key, then press
REDIAL. The phone will automatically dial the number.
HOLD
Press HOLD to place an active call on hold.
The PHONE LED will flash to indicate call is on hold.
Press ON/OFF or HOLD again to return to the call.
If a call is on Hold using VT1711 and the user picks up another phone on the same link, the VT1711 will take itself off hold and turn off. therefore, you do not have to go back to turn the phone off if you go to another extension. It is done automatically.
PAGE
To page from the base, press PAGE.
To cancel the page, either press PAGE again on the base or press ON/OFF on the handset.
ADVANCED FUNCTIONS
TEMPORARY TONE
If you have rotary (dial-pulse) telephone service (TONE/PULSE switch is set to
PULSE), this feature allows you to temporarily switch to TONE dialing for such purposes as remote access to answering machines, bank-by-phone services, use of calling cards and other special services.
1. Dial the call normally.
2. Then activate the Temporar y Tone feature by pressing * (TONE key).
3. You can then press the numbers or symbols you need, and your phone will send the proper tones.
To end the call, press ON/OFF or place the handset back in the base. The phone will automatically go back to rotary (dial-pulse) service.
PROGRAMMING THE RINGER
The handset ringer is capable of four different types of ringing tones. The following section details how to select different ringer types.
CHANGING RINGER TYPES
To program, the handset must be OFF.
To select a different ringer type do the following:
8
* Press FLASH
* Press:
1 for ringer type 1
2 for ringer type 2
3 for ringer type 3
4 for ringer type 4
* A confirmation ring will be heard for the new ringer type.
* The phone will automatically exit ringer programming mode.
TO PROGRAM SPEED DIAL
NUMBERS
The Handset must be OFF.
* Press MEM/PROG. The PHONE LED will flash quickly to indicate that the unit is in program mode.
* Using the dial pad, enter the number you want to store. The number can be up to 16 digits long, including pauses or other special characters.
* Press MEM/PROG once more.
* Enter the two digit memory location you wish to store the number in (01..20).
* If programmed correctly, the phone will emit two short beeps and exit programming mode.
MEMory(SPEED) DIALING
* Press ON/OFF to get dial tone.
* Press MEM/PROG.
* Enter a 2 digit location number (01..20)
* The number stored in that location will be automatically dialed.
CHANGING STORED NUMBERS
To change or replace a stored number, simply store a new number in the desired memory location.
DELETING STORED NUMBERS
To delete a stored number from memory do the following:
BASIC OPERATION
* The handset must be OFF.
* Press MEM/PROG to enter program mode.
* Press MEM/PROG again.
* Enter the two digit memory location that you wish to delete (01..20).
* The phone will emit two short beeps and exit programming mode.
NOTE:Stored numbers are retained in memory even if the base loses its power or the handset battery is removed.
STORING SPECIAL CODES
To insert a pause in a phone number, press PAUSE/REDIAL at the appropriate point when entering the number. This inserts a 2 second pause. For longer pauses, press
PAUSE/REDIAL two or more times. Each press makes the pause 2 seconds longer, and is treated as a stored digit.
If your phone is connected to a PBX you can store the PBX access number and a pause before the phone number. For example, to store 9-PAUSE-555-1234 in memory location 08, do the following:
* The handset must be OFF
* Press MEM/PROG
* Press 9
* Press PAUSE/REDIAL, to insert a two second pause
* Dial 5551234
* Press MEM/PROG
* Press 08 (memory location)
* If programmed correctly, the phone will emit two short beeps and exit programming mode.
ADDITIONAL OPERATING TIPS
If the handset is moved to a point where the base unit and handset can no longer communicate, the handset will beep twice and the LOW BATT LED will flash slowly to
9
BASIC OPERATION
signal Out of Range.
OUT OF RANGE WHEN PHONE IS ON
If you are presently engaged in a phone conversation move closer to the base. If the base unit does not communicate with the handset within 25 seconds of losing contact, it will automatically hang up.
OUT OF RANGE WHEN PHONE IS OFF
If the phone is OFF, the handset and base still monitor each other to make sure that they can communicate. If the handset is moved out of range, the handset will beep twice, and then the LOW BATT LED will flash slowly. The handset will re-link with the base automatically once it is brought back within range. The unit will then be able to receive and place calls.
When the base unit is unplugged from the power supply, the handset will beep twice, and the LOW BATT LED will flash slowly. Plug the base in again and this will stop.
NOISE OR INTERFERENCE
Your VTech VT1711 cordless telephone has auto-channel scan circuitry, which will detect excess noise and change the channel of the phone to reduce it. This is done automatically.
Since the VTech VT1711 is a fully digital phone, it does not suffer from noise associated with regular cordless phones.
At times you may experience occasional
“drop outs”, especially at the extreme edges of the phone’s range. Simply move closer to the base unit and this will disappear.
The RBRC
TM
Seal
The RBRC R Seal on the (easily removable) nickel-cadmium batter y (contained in our product) indicates that VTech
Communications, INC.is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful lives,when taken out of service within the United States and
Canada.
The RBRC R program provides a convenient alternative to placing used nickel-cadmium batteries into the trash or municipal waste,which may be illegal in your areas.
VTech’s participation in RBRC R makes it easy for you to drop off the spent battery at local retailers participating in the RBRC R program or at authorized VTech product service centers.
Please call 1-800-8-BATTERY
TM
for information on Ni-Cd battery recycling and disposal bans/ restrictions in your area.VTech’s involvement in this program is part of its commitment to protecting our environment and conserving natural resources.
Remove the nickel-cadmium battery pack by pressing on the lock knob and sliding downward as mentioned on this manual.
RBRC R is a registered trademark of Rechargeable Battery Recycling Corporation.
10
BASIC OPERATION
LOW BATTERY INDICATOR
PHONE INDICATOR
FLASH KEY
ON/OFF KEY
TONE (Temporary tone)
MEM KEY
REDIAL KEY
HOLD KEY
SPREAD SPECTRUM
LOW BATT PHONE
ON/OFF
PHONE FLASH
1
4 ghi
7 pqrs
* tone
PAUSE
REDIAL
2 abc
5 jkl
8 tuv
0 oper
PROG
MEM
3 def
6 mno
9 wxyz
#
HOLD
DIGITAL
CORDLESS
900
MHZ
VOLUME UP & DOWN
DIALING KEYS
10
9
8
7
6
5
20
19
18
4
3
2
17
16
15
14
MEMOR
1
13
12
11
Y DIALING
SP
ARE B
CHARGING
WER
HANDSET IN-USE
ATTER
Y
SPARE BATTERY
INDICATOR
CHARGING
INDICATOR
HANDSET IN USE
INDICATOR
POWER
INDICATOR
DIGIT
SPREAD SPECTR 900
VT1711
MHZ
UM
PA
GE
PAGE KEY
11
HEADSET OPERATION
Your VT 1711 cordless telephone is equipped with a 2.5mm Headset Jack for use with an optional accessory Headset for hands-free operation.
The headband can be adjusted to fit the contour of your head. Using both hands, slide the headband up or down so that it rests comfortably on your head, with the speaker cushion centered against your ear.
If you choose to use the Headset option, you must obtain an optional accessory
Headset, which is compatible with the VT
1711.
For maximum sound quality, the flexible microphone should be positioned at the corner of your mouth, about one inch from your face.
To purchase a Headset, call
VTech Customer Service at 1-
800-595-9511.
BELT CLIP
Once you have a compatible 2.5mm
Headset, locate the Headset Jack on the
VT 1711 Handset. Connect the plug on the
Headset cord to the jack on the cordless
Handset. The plug should fit securely. Do not force the connection.
The VT 1711 is also equipped with a detachable belt clip. Align the pins on the inside edge of the clip with the notches on the sides of the VT 1711 Handset. The belt clip should snap securely into place. Do not force the connection.
OPERATION
NOTE: Whenever a compatible Headset is connected to the cordless Handset, the microphone on the Handset will be muted.
This is done to limit the effect of background noise.
The following operational characteristics apply to VTech Headsets. The same may also apply to other, non-VTech supplied headsets, but VTech assumes no responsibility for their performance.
The VTech brand compatible Headset has a reversible, monaural design. You can wear your Headset on either ear, leaving one ear free for room conversation.
12
If you have difficulty operating your phone, the suggestions below should solve the problem. If you still have difficulty after trying these suggestions call VTECH
Communications at 1-800-595-9511. In
Canada, call VTECH Electronics at 604-273-
5131.
THE PHONE DOESNT WORK AT ALL.
* Make sure the power cord is plugged in.
* Make sure the telephone line cord is plugged firmly into the base unit and the telephone wall jack.
* Make sure the batteries are properly charged. If the LOW BATT LED is flashing, the battery pack needs charging.
NO DIAL TONE
First check all the suggestions above. If you still don’t hear a dial tone, disconnect the base unit from the telephone jack and connect a different phone. If there is no dial tone on that phone either, the problem is in your wiring or local service. Call your local telephone company.
YOU GET NOISE, STATIC, OR A
WEAK SIGNAL EVEN WHEN
YOURE NEAR THE BASE UNIT.
Household appliances plugged into the same circuit as the base unit can sometimes cause interference. Try moving the appliance or the base unit to another outlet.
YOU GET NOISE, STATIC, OR A
WEAK SIGNAL WHEN YOURE
AWAY FROM THE BASE UNIT.
* You may be out of range. Either move close to the base, or relocate the base unit.
* The layout of your home may be limiting the range. Try moving the base unit to another position.
IN CASE OF DIFFICULTY
THE HANDSET DOES NOT RING WHEN
YOU RECEIVE A CALL.
* Make sure the telephone line cord is plugged firmly into the base unit and the telephone jack. Make sure the power cord is plugged in.
* You may be too far from the base unit.
* You may have too many extension phones on your telephone line to allow all of them to ring. Try unplugging some of the other phones.
YOU HEAR OTHER CALLS WHILE
USING YOUR PHONE.
Disconnect your base unit from the telephone jack, and plug in a regular telephone. If you still hear other calls, the problem is probably in your wiring or local service. Call your local telephone company.
YOU HEAR NOISE IN THE
HANDSET, AND NONE OF THE
KEYS OR BUTTONS WORK.
* Make sure the power cord is plugged in.
* Your base unit and handset may not be operating on the same channel or security code. Place the handset in the cradle for a few moments to reset the channel.
COMMON CURE FOR ELECTRIC
EQUIPMENT
Electronics, like people, can sometimes get confused. If the unit does not seem to be responding normally, then try putting the handset in the cradle. If it does not seem to respond after trying this a few times, do the following (in the order listed):
1. Disconnect the power to the base.
2. Disconnect the handset battery.
3. Wait a few minutes.
4. Connect power to the base.
5. Connect the handset battery.
6. Put the handset in the base.
13
WARRANTY
WARRANTY STATEMENT
WHAT DOES OUR WARRANTY
COVER?
* Any defect in material or workmanship.
FOR HOW LONG AFTER THE
ORIGINAL PURCHASE?
* To the original purchaser only - ONE
YEAR.
WHAT WILL VTECH DO?
* At our option, repair or replace your unit.
HOW DO I SEND MY UNIT, IN OR
OUT OF WARRANTY?
* In the U.S. call VTECH
COMMUNICATIONS CUSTOMRER
SERVICE For Return Authorigation at:
1-800-595-9511,
In Canada call VTECH ELECTRONICS at 1-800-267-7377.
* Properly pack your unit. Include any cables and accessories that were originally provided with the product. We recommend using the original carton and packing materials.
* Include in the package a copy of the sales receipt or other evidence of date or original purchase (if the unit was purchased within the last twelve months).
* Print your name and address, along with a description of the defect, and include this in the package.
* Include payment for any service or repair not covered by warranty, as determined by VTECH Communications.
* Ship the unit via UPS Insured, or equivalent to:
VTECH COMMUNICATIONS
11035 SW 11th STREET BLDG. B
SUITE 270 BEAVERTON, OR 97005
In Canada VTECH ELECTRONICS
SUITE 2007671 Alderbridge Way
Richmord, B.C. U6X 1Z9
VTECH Communications assumes no responsibility for units sent without prior Return Authorization.
WHAT DOES OUR WARRANTY
NOT COVER?
* Batteries
* Damage from misuse, neglect, or acts of nature (lightning, floods, power surges, etc.)
* Products which may have been modified or incorporated into other products
* Products purchased and/or operated outside the USA, its territories, or
Canada.
* Products serviced by the owner or a service facility not expressly authorized by VTECH Communications
* Products purchased more than 12 months from current date
* Units purchased in “AS IS” condition or units purchased as “Distressed
Merchandise”.
HOW DOES STATE LAW RELATE TO
THIS WARRANTY?
* This warranty gives you specific rights.
You may also have other rights that vary from state to state.
14
MAINTENANCE
TAKING CARE OF YOUR TELEPHONE.
Your VTech VT 1711 cordless telephone contains sophisticated electronic parts, so it must be treated with care.
Avoid rough treatment.
Place the handset down gently. Save the original packing materials to protect your telephone if you ever need to ship it.
Avoid Water
Your telephone can be damaged if it gets wet. Do not use the handset outdoors in the rain, or handle it with wet hands. Do not install your base unit near a sink, bathtub, or shower.
Electrical storms
Electrical storms can sometimes cause power surges harmful to electronic equipment.
For your own safety, use caution when using electric appliances during storms.
Cleaning your telephone
Your telephone has a durable plastic casing that should retain its luster for many years. Clean it only with a soft cloth slightly dampened with water or a mild soap. Do not use excess water or cleaning solvents of any kind.
ReMEM/PROGber that electrical appliances can cause serious injury if used when you are wet or standing in water, DO
NOT RETRIEVE IT UNTIL YOU UNPLUG
THE POWER CORD AND TELEPHONE
LINE CORDS FROM THE WALL. Then pull the unit out by the unplugged cords.
TECHNICAL SPECIFICATIONS
Direct Sequence Spread Spectrum Cordless Telephone
FREQUENCY CONTROL
Crystal Controlled PLL Synthesizer
TRANSMIT FREQUENCY
902MHz to 928MHz
NOMINAL EFFECTIVE RANGE
Maximum power allowed by
FCC and IC. Actual operating range may vary according to environmental conditions at the time of use.
15 size
Handset: 186.5(L)X64(W)X45(D)mm
Base:
WEIGHT
Handset:
205(L)X156(W)X57(H)mm
280g
Base: 415g
POWER REQUIREMENTS
Handset: Self-contained nickelcadmium rechargeable battery supply, 3.6V
nominal, 600mAh capacity.
9VDC @ 500mA Base:
MEMORY
Memory Dial: 20 Memory locations
16 Digits per location
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project