Pioneer DEH-2700 CD Player

DEH-2700

This product conforms to CEMA cord colors.

Le code de couleur des câbles utilisé pour ce produit est conforme à CEMA.

Los colores de los cables este producto se conforman con el código de colores CEMA.

Printed in China

Imprimé en Chine

<YRD5017-A/U> UC <KMMZX> <04G00000>

Connecting the Units

Note:

• This unit is for vehicles with a 12-volt battery and negative grounding. Before installing it in a recreational vehicle, truck or bus, check the battery voltage.

• To avoid shorts in the electrical system, be sure to disconnect the

≠ battery cable before beginning installation.

• Refer to the owner’s manual for details on connecting the power amp and other units, then make connections correctly.

• Secure the wiring with cable clamps or adhesive tape. To protect the wiring, wrap adhesive tape around them where they lie against metal parts.

• Route and secure all wiring so it cannot touch any moving parts, such as the gear shift, handbrake and seat rails. Do not route wiring in places that get hot, such as near the heater outlet. If the insulation of the wiring melts or gets torn, there is a danger of the wiring short-circuiting to the vehicle body.

• Don’t pass the yellow lead through a hole into the engine compartment to connect to the battery. This will damage the lead insulation and cause a very dangerous short.

• Do not shorten any leads. If you do, the protection circuit may fail to work when it should.

• Never feed power to other equipment by cutting the insulation of the power supply lead of the unit and tapping into the lead. The current capacity of the lead will be exceeded, causing overheating.

• When replacing the fuse, be sure to only use a fuse of the rating prescribed on this unit.

• Since a unique BPTL circuit is employed, never wire so the speaker leads are directly grounded or the left and right

≠ speaker leads are common.

If you ground the products together and the ground becomes detached, there is a risk of damage to the

• products or fire.

• The black lead is ground. Please ground this lead separately from the ground of high-current products such as power amps.

If you ground the products together and the ground becomes detached, there is a risk of damage to the products or fire.

Speakers connected to this unit must be highpower with minimum rating of 45 W and impedance of 4 to 8 ohms. Connecting speakers with output and/or impedance values other than those noted here may result in the speakers catching fire, emitting smoke, or becoming damaged.

• When this product’s source is switched ON, a control signal is output through the blue/white lead.

Connect to an external power amp’s system remote control or the car’s Auto-antenna relay control terminal (max. 300 mA 12 V DC). If the car features a glass antenna, connect to the antenna booster power supply terminal.

• When an external power amp is being used with this system, be sure not to connect the blue/white lead to the amp’s power terminal. Likewise, do not connect the blue/white lead to the power terminal of the auto-antenna. Such connection could cause excessive current drain and malfunction.

• To avoid a short-circuit, cover the disconnected lead with insulating tape. Insulate the unused speaker leads without fail. There is a possibility of a short-circuit if the leads are not insulated.

• If this unit is installed in a vehicle that does not have an ACC (accessory) position on the ignition switch, the red lead of the unit should be connected to a terminal coupled with ignition switch ON/OFF operations. If this is not done, the vehicle battery may be drained when you are away from the vehicle for several hours. (Fig. 1)

O

F

F

ACC

O

N

T

R

A

S

ACC position

O

F

F

O

N

T

R

A

S

No ACC position

Fig. 1

• Cords for this product and those for other products may be different colors even if they have the same function. When connecting this product to another product, refer to the supplied manuals of both products and connect cords that have the same function.

<ENGLISH>

Rear output

This Product

Antenna jack

Fuse

Jack for the Wired Remote Control

Please see the Instruction Manual for the

Wired Remote Control (sold separately).

Blue/white

To system control terminal of the power amp or Auto-antenna relay control terminal

(max. 300 mA 12 V DC).

Yellow

To terminal always supplied with power regardless of ignition switch position.

Red

To electric terminal controlled by ignition switch (12 V DC)

ON/OFF.

Black (ground)

To vehicle (metal) body.

With a 2 speaker system, do not connect anything to the speaker leads that are not connected to speakers.

Perform these connections when using the optional amplifier.

White

Front speaker

+

Left

Rear speaker

+

White/black

Green

Green/black

Rear speaker

+

Connecting cords with RCA pin plugs

(sold separately)

System remote control

Gray

Gray/black

Violet

Violet/black

+

+

Front speaker

Right

Rear speaker

+

Rear speaker

Power amp

(sold separately)

Fig. 2

Installation

Note:

• Before making a final installation of the unit, temporarily connect the wiring to confirm that the connections are correct and the system works properly.

• Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.

• Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle.

• Install the unit where it does not get in the driver’s way and cannot injure the passenger if there is a sudden stop, like an emergency stop.

• The semiconductor laser will be damaged if it overheats, so don’t install the unit anywhere hot

— for instance, near a heater outlet.

• If installation angle exceeds 60° from horizontal, the unit might not give its optimum performance.

(Fig. 3)

60

°

Fig. 3

DIN Front/Rear-mount

This unit can be properly installed either from “Front” (conventional DIN Front-mount) or

“Rear” (DIN Rear-mount installation, utilizing threaded screw holes at the sides of unit chassis). For details, refer to the following illustrated installation methods.

DIN Front-mount

Installation with the rubber bush (Fig. 4)

Dashboard

182

Holder

After inserting the holder into the dashboard, then select the appropriate tabs according to the thickness of the dashboard material and bend them.

(Install as firmly as possible using the top and bottom tabs. To secure, bend the tabs 90 degrees.)

53

Rubber bush

Screw

Removing the Unit (Fig. 5) (Fig. 6)

Frame

To remove the frame, extend top and bottom of the frame outwards in order to unlock it. (When reattaching the frame, point the side with a groove downwards and attach it.)

• It becomes easy to remove the frame if the front panel is released.

Fig. 5

Insert the supplied extraction keys into the unit, as shown in the figure, until they click into place. Keeping the keys pressed against the sides of the unit, pull the unit out.

Fig. 6

Fig. 4

DIN Rear-mount

Installation using the screw holes on the side of the unit

1. Remove the frame. (Fig. 7)

Frame

To remove the frame, extend top and bottom of the frame outwards in order to unlock it. (When reattaching the frame, point the side with a groove downwards and attach it.)

• It becomes easy to remove the frame if the front panel is released.

Fig. 7

2. Fastening the unit to the factory radio mounting bracket.

(Fig. 8) (Fig. 9)

Select a position where the screw holes of the bracket and the screw holes of the head unit become aligned (are fitted), and tighten the screws at 2 places on each side. Use either truss screws (5

×

8 mm) or flush surface screws

(5

×

9 mm), depending on the shape of the screw holes in the bracket

.

10

Fig. 8

<ENGLISH>

About the fixing screws for the front panel

If you do not operate the Detaching and Replacing the Front Panel Function, use the supplied fixing screws and fix the front panel to this unit.

Fixing screw

Fig. 10

Fig. 9

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project