Sony AVD-S10 DVD Player

Sony AVD-S10 DVD Player
4-240-874-11(2)
Super Audio CD/
DVD RECEIVER
Operating Instructions
AVD-S10
© 2002 Sony Corporation
WARNING
Welcome!
To prevent fire or shock
hazard, do not expose the unit
to rain or moisture.
Do not install the appliance in a
confined space, such as a bookcase
or built-in cabinet.
To prevent fire, do not Cover the
ventilation of the apparatus with
news papers, table-cloths, curtains,
etc. And don’t place lighted candles
on the apparatus.
To prevent fire or shock hazard, do
not place objects filled with liquids,
such as vases, on the apparatus.
Thank you for purchasing this Sony
Super Audio CD/DVD receiver.
Before operating this receiver, please
read this manual thoroughly and
retain it for future reference.
This appliance is classified as a
CLASS 1 LASER product. The label
is located on the rear exterior.
The following caution label is
located inside the receiver.
Don’t throw
away the battery
with general
house waste,
dispose of it
correctly as
chemical waste.
2GB
Precautions
Safety
• If anything falls into the cabinet,
unplug the unit and have it
checked by qualified personnel
before operating it any further.
• The unit is not disconnected from
the mains as long as it is
connected to the mains outlet,
even if the unit itself has been
turned off.
• Unplug the unit from the wall
outlet if you do not intend to use it
for an extended period of time. To
disconnect the cord, pull it out by
the plug, never by the cord.
Installing
• Allow adequate air circulation to
prevent internal heat buildup.
• Do not place the unit on surfaces
(rugs, blankets, etc.) or near
materials (curtains, draperies) that
may block the ventilation slots.
• Do not install the unit near heat
sources such as radiators, or air
ducts, or in a place subject to
direct sunlight, excessive dust,
mechanical vibration, or shock.
• Do not install the unit in an
inclined position. It is designed to
be operated in a horizontal
position only.
• Keep the unit and discs away from
equipment with strong magnets,
such as microwave ovens, or large
loudspeakers.
• Do not place heavy objects on the
unit.
• If the unit is brought directly from
a cold to a warm location,
moisture may condense inside the
Compact AV System and cause
damage to the lenses. When you
first install the unit, or when you
move it from a cold to a warm
location, wait for about 30 minutes
before operating the unit.
Precautions
On safety
Should any solid object or liquid fall into the
cabinet, unplug the receiver and have it checked
by qualified personnel before operating it any
further.
On power sources
• The unit is not disconnected from the AC power
source (mains) as long as it is connected to the
wall outlet, even if the unit itself has been
turned off.
• AC power cord must be changed only at the
qualified service shop.
On placement
• Place the receiver in a location with adequate
ventilation to prevent heat build-up in the
receiver.
• At high volume, over long periods of time, the
cabinet becomes hot to the touch. This is not a
malfunction. However, touching the cabinet
should be avoided. Do not place the unit in a
confined space where ventilation is poor as this
may cause overheating.
• Do not block the ventilation slots by putting
anything on the receiver. The receiver is
equipped with a high power amplifier. If the
ventilation slots on the top surface are blocked,
the unit can overheat and malfunction.
• Do not place the receiver on a soft surface such
as a rug that might block the ventilation holes
on the bottom.
• Do not place the receiver in a location near heat
sources, or in a place subject to direct sunlight,
excessive dust, or mechanical shock.
On operation
• If the receiver is brought directly from a cold to
a warm location, or is placed in a very damp
room, moisture may condense on the lenses
inside the receiver. Should this occur, the
receiver may not operate properly. In this case,
remove the disc and leave the receiver turned on
for about half an hour until the moisture
evaporates.
• When you move the receiver, take out any discs.
If you don’t, the disc may be damaged.
• For power saving purposes, the receiver can be
completely turned off by the POWER button on
the main unit. Though the LED remains lit for a
while, the receiver is completely off.
On adjusting volume
Do not turn up the volume while listening to a
section with very low level inputs or no audio
signals. If you do, the speakers may be damaged
when a peak level section is played.
On cleaning
Clean the cabinet, panel, and controls with a soft
cloth slightly moistened with a mild detergent
solution. Do not use any type of abrasive pad,
scouring powder or solvent such as alcohol or
benzine.
If you have any questions or problems concerning
your receiver, please consult your nearest Sony
dealer.
On cleaning discs
Do not use a commercially available CD/DVD
cleaning disc. It may cause a malfunction.
On your TV’s colour
If the speakers should cause the TV screen to have
colour irregularity, turn off the TV at once then
turn it on after 15 to 30 minutes. If colour
irregularity should persist, place the speakers
further away from the set.
IMPORTANT NOTICE
Caution: This receiver is capable of holding a
still video image or on-screen display image on
your television screen indefinitely. If you leave
the still video image or on-screen display image
displayed on your TV for an extended period of
time you risk permanent damage to your
television screen. Projection televisions are
especially susceptible to this.
3GB
Table of Contents
WARNING .......................................................................................................... 2
Welcome! ........................................................................................................... 2
Precautions ........................................................................................................ 3
About this Manual .............................................................................................. 6
This receiver Can Play the Following Discs ....................................................... 6
Notes about the Discs ........................................................................................ 8
Index to Parts and Controls ............................................................................... 9
Guide to the Control Menu Display (Magic Pad) .............................................. 13
Getting Started ................................................................ 15
Quick Overview ................................................................................................
Unpacking ........................................................................................................
Inserting Batteries into the Remote .................................................................
Step 1: Speaker System Hookup .....................................................................
Step 2: Antenna Hookups ................................................................................
Step 3: TV Hookups .........................................................................................
Step 4: Hooking Up the Receiver .....................................................................
Speaker Setup .................................................................................................
Presetting Radio Stations ................................................................................
15
15
16
16
19
21
22
23
28
Playing Discs .................................................................. 30
Playing Discs ...................................................................................................
Resuming Playback from the Point Where You Stopped the Disc
(Resume Play) ...........................................................................................
Using the DVD’s Menu .....................................................................................
Playing VIDEO CDs with PBC Functions (PBC Playback) ..............................
Creating Your Own Programme (Programme Play) .........................................
Playing in random order (Shuffle Play) ............................................................
Playing repeatedly (Repeat Play) ....................................................................
30
31
32
33
34
36
36
Searching for a Scene ....................................................... 38
Searching for a Particular Point on a Disc (Scan, Slow-motion Play) .............. 38
Searching for a Title/Chapter/Track/Index/Scene ............................................. 39
Viewing Information About the Disc ....................................... 41
Viewing the Playing Time and Remaining Time on the Front Panel Display .... 41
Checking the Playing Time and Remaining Time ............................................ 42
4GB
Sound Adjustments ........................................................... 44
Changing the Sound ........................................................................................
Automatically decoding the input audio signal (Auto Format Decode) ............
Enjoying Surround Sound ................................................................................
Using only the front speakers (2 Channel Stereo) ...........................................
Adjusting the level parameters .........................................................................
44
46
46
50
50
Enjoying Movies .............................................................. 51
Changing the Angles ....................................................................................... 51
Displaying the Subtitles ................................................................................... 52
Checking the Play Information (ADVANCED) .................................................. 53
Using Various Additional Functions ....................................... 54
Locking Discs (CUSTOM PARENTAL CONTROL, PARENTAL CONTROL) ... 54
Other Operations ............................................................. 59
Controlling the TV with the Supplied Remote ..................................................
Watching the Video or other Unit .....................................................................
Listening to the Radio ......................................................................................
Using the Radio Data System (RDS) ...............................................................
Naming Preset Stations ...................................................................................
59
60
61
62
62
Settings and Adjustments ................................................... 64
Using the Setup Display ..................................................................................
Setting the Display or Sound Track Language (LANGUAGE SETUP) .............
Settings for the Display (SCREEN SETUP) .....................................................
Custom Settings (CUSTOM SETUP) ...............................................................
Settings for the Speakers (SPEAKER SETUP) ...............................................
64
65
66
67
68
Additional Information ....................................................... 72
Troubleshooting ...............................................................................................
Self-diagnosis Function (When letters/numbers appear on the front panel
display) .......................................................................................................
Glossary ..........................................................................................................
Specifications ...................................................................................................
Language Code List .........................................................................................
DVD Setup Menu List ......................................................................................
Index ................................................................................................................
72
75
75
78
80
81
82
5GB
Terms for discs
About this Manual
• The instructions in this manual describe
the controls on the remote. You can also
use the controls on the receiver if they
have the same or similar names as those on
the remote.
• The icons used in this manual are
explained below:
Icon
Meaning
Icon
Meaning
Functions
available in
DVD video
mode
Functions
available in
Super Audio
CD and
Audio CD
mode
Functions
available in
VIDEO
CD mode
Functions
available in
CD mode
More
convenient
features
z
This receiver Can Play
the Following Discs
Format of discs
DVD VIDEO
• Title
The longest sections of a picture or music
feature on a DVD, movie, etc., in video
software, or the entire album in audio
software. Each title is assigned a title
number enabling you to locate the title you
want.
• Chapter
Sections of a picture or a music piece that
are smaller than titles. A title is composed
of several chapters. Each chapter is
assigned a chapter number enabling you to
locate the chapter you want. Depending on
the disc, no chapters may be recorded.
• Track
Sections of a picture or a music piece on a
VIDEO CD, Super Audio CD, or CD.
Each track is assigned a track number
enabling you to locate the track you want.
• Index (Super Audio CD, CD) / Video
Index (VIDEO CD)
A number that divides a track into sections
to easily locate the point you want on a
VIDEO CD, Super Audio CD, or CD.
Depending on the disc, no indexes may be
recorded.
• Scene
On a VIDEO CD with PBC functions
(page 33), the menu screens, moving
pictures and still pictures are divided into
sections called “scenes.” Each scene is
assigned a scene number enabling you to
locate the scene you want.
Disc
Super Audio CD
DVD
structure
Title
Chapter
VIDEO CD
Music CD
The “DVD VIDEO” logo is a trademark.
6GB
VIDEO CD,
Super
Audio CD,
or CD
structure
Disc
Track
Index
Note on PBC (Playback Control)
(VIDEO CDs)
This receiver conforms to Ver. 1.1 and Ver.
2.0 of VIDEO CD standards. You can enjoy
two kinds of playback depending on the disc
type.
You can
Enjoy video playback
(moving pictures) as well
as music.
Disc type
VIDEO CDs
without PBC
functions
(Ver. 1.1 discs)
VIDEO CDs
with PBC
functions
(Ver. 2.0 discs)
Play interactive software
using menu screens
displayed on the TV screen
(PBC Playback), in
addition to the video
playback functions of Ver.
1.1 discs. Moreover, you
can play high-resolution
still pictures, if they are
included on the disc.
Region code
Your receiver has a region code printed on
the back of the unit and will only play
DVDs labelled with the same region code.
DVDs labelled
will also play on this
receiver.
If you try to play any other DVD, the
message “Playback prohibited by area
limitations.” will appear on the TV screen.
Depending on the DVD, no region code
indication may be labelled even though
playing the DVD is prohibited by area
restrictions.
ALL
Examples of discs that the receiver
cannot play
The receiver cannot play the following
discs:
• CD-ROMs (PHOTO CDs included)
• All CD-Rs other than music and VCD
formatted CD-Rs
• Data part of CD-Extras
• DVD-ROMs
• DVD Audio discs
• A DVD with a different region code (page
7, 77).
• A disc that has a non-standard shape (e.g.,
card, heart)
• A disc with paper or stickers on it.
• A disc that has the adhesive, cellophane
tape, or a sticker still left on it.
Note
Some CD-Rs or CD-RWs cannot be played on this
receiver depending upon the recording quality or
physical condition of the disc, or the characteristics
of the recording device.
Furthermore, the disc will not play if it has not been
correctly finalized. For more information, see the
operating instructions for the recording device.
Note on playback operations of
DVDs and VIDEO CDs
Some playback operations of DVDs and
VIDEO CDs may be intentionally set by
software producers. Since this receiver plays
DVDs and VIDEO CDs according to the
disc contents the software producers
designed, some playback features may not
be available. Also, refer to the instructions
supplied with the DVDs or VIDEO CDs.
7GB
Copyrights
This product incorporates copyright
protection technology that is protected by
method claims of certain U.S. patents, other
intellectual property rights owned by
Macrovision Corporation, and other rights
owners. Use of this copyright protection
technology must be authorized by
Macrovision Corporation, and is intended
for home and other limited viewing uses
only unless otherwise authorized by
Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
This receiver incorporates Dolby* Digital,
Pro Logic Surround, and the DTS** Digital
Surround System.
* Manufactured under license from Dolby
Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol
are trademarks of Dolby Laboratories.
Confidential unpublished works. © 1992-1997
Dolby Laboratories. All rights reserved.
** Manufactured under license from Digital Theater
Systems, Inc. US Pat. No. 5,451,942 and other
worldwide patents issued and pending. “DTS” and
“DTS Digital Surround” are trademarks of Digital
Theater Systems, Inc. © 1996 Digital Theater
Systems, Inc. All rights reserved.
Notes about the Discs
On handling discs
• To keep the disc clean, handle the disc by
its edge. Do not touch the surface.
• Do not stick paper or tape on the disc.
• Do not expose the disc to direct sunlight or
heat sources such as hot air ducts, or leave
it in a car parked in direct sunlight as the
temperature may rise considerably inside
the car.
• After playing, store the disc in its case.
On cleaning
• Before playing, clean the disc with a
cleaning cloth.
Wipe the disc from the centre out.
• Do not use solvents such as benzine,
thinner, commercially available cleaners,
or anti-static spray intended for vinyl LPs.
8GB
Index to Parts and Controls
For more information, refer to the pages indicated in parentheses.
Front Panel
–
PRESET
+
VOLUME
STANDBY
DISPLAY
POWER
SOUND FIELD
–
1
2
3
4
5
6
7
8
POWER switch (30)
STANDBY indicator (30)
Disc tray (30)
A (open/close) (30)
H (play) (30)
X (pause) (31)
x (stop) (30)
./>, PRESET +/– (28, 31)
9
q;
qa
qs
qd
qf
qg
qh
BAND
FUNCTION
PHONES
+
VOLUME control (30)
PHONES jack (30)
FUNCTION (60)
BAND (28)
SOUND FIELD +/– (46)
DISPLAY (61)
Front panel display (10)
(remote sensor) (16)
continued
9GB
Front Panel Display
When playing back a DVD
Current surround
format
Playing status
ALL 1 DISC S AUTO TITLE
PRO LOGIC
DIGITAL FM AM
NTSC PBC ANGLE
Lights up when you
can change the angle
Current chapter number
TRACK
CHAPTER INDEX
Current sound
H TUNED
M MONO ST S
dB REPEAT 1
k H z PROGRAM
M H z SHUFFLE
Current title
number
Playing time
Current play mode
When playing back a Super Audio CD, CD, or VIDEO CD
Current index number
(The index indicator does not appear
during Super Audio CD playback.)
Playing status
ALL 1 DISC S AUTO
TITLE
TRACK
CHAPTER INDEX
H TUNED
Current sound
M MONO ST S
dB REPEAT 1
k H z PROGRAM
M H z SHUFFLE
DIGITAL FM AM
NTSC PBC ANGLE
Lights up during
PBC playback
(VIDEO CD only)
Playing time
Current track number
Current play mode
When listening to the radio
Preset number
ALL 1 DISC S AUTO TITLE
PRO LOGIC
DIGITAL FM AM
NTSC PBC ANGLE
Current band
10GB
TRACK
Monaural/Stereo effect
CHAPTER INDEX
H TUNED
M MONO ST S
dB REPEAT 1
k H z PROGRAM
M H z SHUFFLE
Current station
Rear Panel
EURO AV
SPEAKERS
FRONT
R
AM
COAXIAL
FM
75Ω
ANT
OPTICAL
(CD ONLY)
L
OUT
OPTICAL
1
2
AUDIO
OUT
IMPEDANCE USE 6–16Ω
CENTER
L
+
+
+
–
–
–
SURROUND
R
L
+
–
IN
R
ANALOG
DIGITAL OUT DIGITAL IN
SUB
WOOFER
1 AM antenna (19)
2 T EURO AV OUTPUT (TO TV) jack
(21)
3 t EURO AV INPUT (FROM VIDEO)
jack (22)
4 SUBWOOFER AUDIO OUT jack (17)
R
L
R
L
5 SPEAKERS jacks (17)
6 DIGITAL IN OPTICAL 1/2 jacks
7 DIGITAL OUT OPTICAL (CD ONLY)
jack
8 ANALOG IN/OUT L/R jacks
9 FM 75Ω COAXIAL antenna jack (20)
continued
11GB
Remote
Note
This remote control glows in the dark. However,
before glowing, the remote must be exposed to light
for awhile.
12GB
1
2
3
4
5
6
7
8
9
0
qa
qs
qd
qf
qg
qh
qj
qk
ql
w;
wa
ws
wd
wf
wg
wh
wj
wk
wl
e;
ea
es
ed
ef
eg
eh
ej
ek
el
RM SET UP (59)
OPEN/CLOSE (30)
BAND (28)
FUNCTION (60)
MEMORY (28)
NAME (63)
PLAY MODE (34)
REPEAT (37)
Number buttons (32)
./>, PRESET +/– (28, 31)
H (play) (30)
X (pause) (31)
DVD TOP MENU (32)
C/X/x/c/ENTER (24)
DVD DISPLAY (13, 36)
TV CH +/– (60)
TV VOL +/– (60)
TV [/1 (on/standby) (60)
[/1 (on/standby) (30)
STEREO/MONO (61)
DISPLAY (61)
SOUND FIELD +/– (46)
TIME (41)
DIMMER (27)
AUDIO (44)
ANGLE (51)
SUBTITLE (52)
ENTER
CLEAR (35)
m/M (28, 38)
x (stop) (30)
MUTING (31)
DVD MENU (32)
VOLUME +/– (30)
O RETURN (33)
TV/VIDEO (60)
AMP MENU (24)
DVD SETUP (64)
WIDE (60)
Guide to the Control Menu Display (Magic Pad)
Use the Control Menu to select a function that you’d like to use. The Control Menu display
appears when the DVD DISPLAY button is pressed. For details, refer to the page in
parentheses.
Control Menu
Total number of titles or tracks recorded
Current playing title number (Video CD/
Super Audio CD/CD: track number)
Current playing chapter
number (Video CD/Super
Audio CD/CD: index number)
Playing time
Playback status
(NPlayback, XPause, xStop, etc.)
12(27)
18(34)
T
1:32:55
Icon of selected
Control Menu item
DVD
SUBTITLE
Select:
Type of disc being
played back
Current setting
OFF
OFF
1: ENGLISH
2: FRENCH
3: SPANISH
Control Menu items
Function name of selected
Control Menu item
Total number of chapters or indexes recorded
Options
ENTER
Cancel:
RETURN
Operation message
List of Control Menu Items
TITLE (DVD only) (page 39)/
SCENE (only VIDEO CD in PBC
playback) (page 39)/TRACK (VIDEO CD
only) (page 39)
Selects the title (DVD), the scene (VIDEO
CD in PBC playback), or the track
(VIDEO CD) to be played.
CHAPTER (DVD only) (page
39)/INDEX (VIDEO CD only) (page 39)
Selects the chapter (DVD) or the index
(VIDEO CD) to be played.
TRACK (Super Audio CD/CD
only) (page 39)
Selects the track (Super Audio CD/CD) to
be played.
INDEX (Super Audio CD/CD
only) (page 39)
Selects the index (Super Audio CD/CD) to
be played.
TIME/TEXT (page 40)
Checks the elapsed time and the remaining
playback time.
Inputs the time code for picture and music
searching.
Displays the DVD or the Super Audio CD/
CD text.
continued
13GB
AUDIO (page 44)
Changes the audio setting.
SUBTITLE (DVD only) (page
Displays the subtitles.
Changes the subtitle language.
ANGLE (DVD only) (page 51)
Changes the angle.
REPEAT (page 36)
Plays the entire disc (all titles/all tracks)
repeatedly, or one title/chapter/track
repeatedly.
52)
ADVANCED (DVD only)
(page 53)
Checks the information (bit rate or layer)
on the disc while playing a DVD.
CUSTOM PARENTAL
CONTROL (page 54)
Sets the disc to prohibit playing.
SETUP (page 64)
CUSTOM Setup
By using the Setup Display, you can make
various adjustments to items such as
picture and sound. You can also set a
language for the subtitles and the Setup
Display, among other things.
RESET
Returns the settings in “SETUP” to the
default setting.
z Each time you press DVD DISPLAY, the Control Menu display changes as follows:
, Control Menu display
m
ADVANCED display (Appears if you select any setting other than “OFF.” See page 53.)
m
Control Menu display off
The Control Menu items are different depending on the disc.
z The Control Menu icon indicator lights up in green
t
when you select “REPEAT” unless
you set the REPEAT PLAY setting to “OFF.” The “ANGLE” indicator lights up in green only when the angles can
be changed.
14GB
Getting Started
Quick Overview
This chapter presents a quick overview so you can begin enjoying your new receiver right away.
For selecting a language used in the on-screen display, refer to page 65.
For selecting the aspect ratio of the TV to be connected, refer to page 66.
Check that you have the following items:
• AM loop antenna (1)
• FM wire antenna (1)
• SCART (EURO AV) cord (1)
• Remote Commander (remote) RM-SP10 (1)
• R6 (size AA) batteries (2)
Getting Started
Unpacking
15GB
Inserting Batteries into the Remote
You can control the receiver using the supplied remote. Insert two R6 (size AA) batteries by
matching the 3 and # ends on the batteries to the markings inside the compartment. When
using the remote, point it at the remote sensor on the receiver.
Notes
•
•
•
•
Do not leave the remote in an extremely hot or humid place.
Do not use a new battery with an old one.
Do not drop any foreign object into the remote casing, particularly when replacing the batteries.
Do not expose the remote sensor to direct light from the sun or lighting apparatus. Doing so may cause a
malfunction.
• If you do not use the remote for an extended period of time, remove the batteries to avoid possible damage from
battery leakage and corrosion.
Step 1: Speaker System Hookup
You can enjoy surround sound by connecting 5 speakers (front L/R speakers, centre speaker,
rear L/R speakers) and active subwoofer to the receiver. If you do not connect 5 speakers and
active subwoofer to the receiver, the receiver optimizes the surround signal depending on the
number of connected speakers. When you connect 2 speakers to the receiver, connect the
speakers to the SPEAKERS FRONT L/R jacks.
Notes
•
•
•
•
16GB
Be sure to match the speaker cord to the appropriate terminal: 3 to 3, # to #, L to L, and R to R jack.
Use the high performance speakers.
Use the same size and performance speakers for the front, centre, and rear speakers.
To obtain the best possible surround sound, specify the speaker parameters (number, distance, level, etc.) on page
23.
Terminals for connecting the speakers
To the
SPEAKERS FRONT L and R terminals
SPEAKERS REAR L and R terminals
SPEAKERS CENTER terminal
SUBWOOFER AUDIO OUT terminal
SPEAKERS
EURO AV
IMPEDANCE USE 6–16Ω
FRONT
R
AM
COAXIAL
OPTICAL
(CD ONLY)
L
AUDIO
OUT
OPTICAL
1
2
+
+
+
–
–
–
R
75Ω
ANT
CENTER
L
SURROUND
L
R
+
–
IN
OUT
FM
Getting Started
Connect the
Front speakers
Rear speakers
Centre speaker
Subwoofer
ANALOG
DIGITAL OUT DIGITAL IN
R
SUB
WOOFER
+
+
–
L
R
L
–
Centre speaker
Front speaker (R)
+
–
Front speaker (L)
Subwoofer
(active type)
+
–
Rear speaker (R)
+
–
Rear speaker (L)
17GB
To avoid short-circuiting the speakers
Short-circuiting of the speakers may damage the receiver. To prevent this, be sure to follow
these precautions when connecting the speakers. Make sure the bare wire of each speaker cord
does not touch another speaker terminal or the bare wire of another speaker cord.
Examples of poor conditions of the speaker cord
Stripped speaker cord is
touching another speaker
terminal.
Stripped cords are touching
each other due to excessive
removal of insulation.
After connecting all the components, speakers, and AC power cord (mains lead), output a test
tone to check that all the speakers are connected correctly. For details on outputting a test tone,
see page 26.
If no sound is heard from a speaker while outputting a test tone, or a test tone is output from a
speaker other than the one currently displayed on the front panel display, the speaker may be
short-circuited. If this happens, check the speaker connection again.
Notes
• Be sure to match the speaker cord to the appropriate terminal on the components: 3 to 3, and # to #. If the
cords are reversed, the sound will be distorted and will lack bass.
• If you use front speakers with low maximum input rating, adjust the volume carefully to avoid excessive output
on the speakers.
18GB
Step 2: Antenna Hookups
Connect the supplied AM/FM antennas for listening to the radio.
Connect the
AM loop antenna
FM wire antenna
Getting Started
Terminals for connecting the antennas
To the
AM terminals
FM 75Ω COAXIAL terminal
AM loop antenna
FM wire antenna
SPEAKERS
EURO AV
FRONT
R
AM
COAXIAL
FM
75Ω
ANT
OPTICAL
(CD ONLY)
L
OPTICAL
1
2
AUDIO
OUT
IMPEDANCE USE 6–16Ω
CENTER
L
+
+
+
–
–
–
SURROUND
L
R
+
–
IN
OUT
R
ANALOG
DIGITAL OUT DIGITAL IN
SUB
WOOFER
R
L
R
L
Notes
• To prevent noise pickup, keep the AM loop antenna away from the receiver and other components.
• Be sure to fully extend the FM wire antenna.
• After connecting the FM wire antenna, keep it as horizontal as possible.
continued
19GB
z If you have poor FM reception
Use a 75-ohms coaxial cable (not supplied) to connect the receiver to an outdoor FM antenna as shown below.
Outdoor FM antenna
System
Earth wire
(not supplied)
AM
COAXIAL
FM
75Ω
To earth
Note
If you connect the receiver to an outdoor antenna, ground it to protect against lightning. To prevent a gas explosion,
do not connect the earth wire to a gas pipe.
20GB
Step 3: TV Hookups
Connect a SCART (EURO AV) cord (supplied) and mains lead in the order (1 – 3) shown
below. Be sure to connect the SCART (EURO AV) cord to the T EURO AV OUTPUT (TO
TV) jack on the receiver. Also, be sure to connect the mains lead last.
Plug cords securely to prevent unwanted noise.
Refer to the instructions supplied with the TV.
The receiver cannot output the S video signal.
The receiver cannot output the audio signal of the connected TV. When you listen to the audio signal of the TV
by using the connected speakers, input the audio signal of the TV from the t EURO AV INPUT (FROM
VIDEO) jack.
Getting Started
Notes
•
•
•
•
Super Audio CD/DVD receiver
SPEAKERS
EURO AV
FRONT
R
AM
COAXIAL
FM
75Ω
ANT
OPTICAL
(CD ONLY)
L
OPTICAL
1
2
IMPEDANCE USE 6–16Ω
CENTER
L
+
+
+
–
–
–
AUDIO
OUT
SURROUND
R
L
+
–
IN
OUT
R
ANALOG
DIGITAL OUT DIGITAL IN
SUB
WOOFER
R
L
R
L
To T EURO AV OUTPUT (TO TV) jack
2 a mains lead
TV
3 a mains lead
1 SCART (EURO AV) cord
(supplied)
To SCART (EURO AV) input
When you connect using the SCART (EURO AV) cord, check that the TV conforms to S video
or RGB signals. If the TV conforms to S video, change the input mode of the TV to RGB
signals. Refer to the operating instructions supplied with the TV to be connected. Also, when
you set “LINE” to “VIDEO” or “RGB” (same as TV) under “CUSTOM SETUP” in the Setup
Display (page 67), use a SCART (EURO AV) cord that conforms to each signal.
When connecting to a standard 4:3 screen TV
Depending on the disc, the image may not fit your TV screen.
If you want to change the aspect ratio, please refer to page 66.
21GB
Step 4: Hooking Up the Receiver
Note
Refer to the instructions supplied with the components to be connected.
Connecting the VCR to the receiver
Connect the SCART (EURO AV) cord (not supplied) to the t EURO AV INPUT (FROM
VIDEO) jack. Be sure to make the connections firmly to avoid hum and noise.
Super Audio CD/DVD receiver
SPEAKERS
EURO AV
FRONT
R
AM
COAXIAL
FM
75Ω
ANT
OPTICAL
(CD ONLY)
L
OPTICAL
1
2
AUDIO
OUT
IMPEDANCE USE 6–16Ω
CENTER
L
+
+
+
–
–
–
SURROUND
L
R
+
–
IN
OUT
R
ANALOG
DIGITAL OUT DIGITAL IN
SUB
WOOFER
R
L
R
L
To t EURO AV INPUT (FROM VIDEO) jack
To SCART (EURO AV)
SCART (EURO AV) cord
(not supplied)
Notes
• Do not connect the receiver to a VCR. If you pass the receiver signals via the VCR, you may not receive a clear
image on the TV screen.
• If you cannot view the pictures from a VCR through this receiver which is connected to a TV with RGB
component jacks, set
to t (Audio/Video) on your TV. When you select
(RGB), the TV cannot receive
the signal from the VCR.
• If you want to use your VCR’s SmartLink function, connect the VCR to your TV’s SmartLink jack.
• The SmartLink function may not work properly if your VCR is connected to your TV via the SCART (EURO
AV) jacks on the receiver.
• When you connect the receiver to your TV via the SCART (EURO AV) jacks, the TV’s input source is set to the
receiver automatically when you start playback or press any button except for POWER on the receiver or [/1 on
the remote. In this case, press TV/VIDEO on the remote to return the input to the TV.
• The receiver does not output the S video signal.
• When you select “DVD” by pressing FUNCTION (page 60), the video signal and RGB signal do not output
from the t EURO AV INPUT (FROM VIDEO) jack. Also, the receiver cannot output the S video signal.
• When you select “VIDEO” by pressing FUNCTION (page 60), the audio signal from the t EURO AV INPUT
(FROM VIDEO) jack is output to the connected speakers. The audio signal does not output from theT EURO
AV OUTPUT (TO TV) jack.
When you play a disc recorded in the NTSC colour system, the receiver outputs the video signal or the Setup
Display etc. in the NTSC colour system and the picture may not appear on the PAL colour system televisions.
In this case, open the tray and remove the disc.
22GB
Speaker Setup
Getting Started
For the best possible surround sound, all the speakers other than the subwoofer should be the
same distance from the listening position (A).
However, this receiver allows you to place the centre speaker up to 1.6 meters (5.0 feet) closer
(B) and the rear speakers up to 4.6 meters (15.0 feet) closer (C) to the listening position.
The front speakers can be placed from 1.0 to 15.0 meters (3.0 to 50.0 feet) (A) from the
listening position.
You can place the subwoofer in any position.
You can place the rear speakers either behind you or to the side, depending on the shape of your
room, etc.
When the rear speakers are placed to the side
When the rear speakers are placed behind you
B
B
A
A
A
45°
A
45°
C
C
90°
20°
C
C
90°
20°
Note
Do not place the centre and rear speakers farther away from the listening position than the front speakers.
Specifying the speaker parameters
To obtain the best possible surround sound, first specify the distance of the speakers from your
listening position, then set the balance and level. Use the test tone to adjust the speaker volumes
to the same level.
You may adjust the speaker parameters using SPEAKER SETUP in the setup display (page 68).
continued
23GB
C/X/x/c/ENTER
AMP MENU
To specify the size, distance, position and height of the speakers
1
2
Press AMP MENU repeatedly to display 9 SP. SETUP on the front panel display.
3
Set the parameter using C/c.
The selected parameter will appear on the front panel display.
4
Repeat Steps 2 and 3 to set other parameters in 9 SP. SETUP.
If you do not operate the remote for a few seconds, the parameter turns off and is stored in
the receiver.
Sit in your listening position and select the item to be set using X/x.
• Items set in 9 SP. SETUP
– Size of 5 speakers (front L/R, centre, rear L/R)
– with or without the subwoofer
– Distance of the front, rear, and centre speakers
– Position and height of the rear speakers
xSIZE
When you do not connect centre or rear speakers, or move the rear speakers, set the parameters
for F.SP., C.SP., R.SP., and S.W. The default settings are underlined.
• F.SP. (front speaker)
–LARGE: Normally select this.
–SMALL: Select this if the small speakers are used for the front speaker.
• C.SP. (centre speaker)
–LARGE: Normally select this.
–SMALL: Select this if the small speaker is used for the centre speaker.
–NO: Select this if no centre speaker is used.
24GB
Getting Started
• R.SP. (rear speakers)
–LARGE: Normally select this. Specify the position and height to implement the Digital
Cinema Surround modes in the “Virtual” sound field (page 48) properly.
–SMALL: Select this if the small speakers are used for the rear speaker. Specify the position
and height to implement the Digital Cinema Surround modes in the “Virtual” sound field
(page 48) properly.
–NO: Select this if no rear speakers are used.
• S.W. (subwoofer)
–YES: Select this if the subwoofer is used.
–NO: Select this if no subwoofer is used.
xDISTANCE
You can vary the distance of each speaker as follows. The default settings are underlined.
• F. D. 5 m (17 ft) (front speakers distance)
Front speaker distance can be set in 0.2 meter (1.0 foot) steps from 1.0 to 15.0 meters (3.0 to
50.0 feet).
• C. D. 5 m (17 ft) (centre speaker distance)
Centre speaker distance can be set in 0.2 meter (1.0 foot) steps from the front speaker distance
to 1.6 meters (5.0 feet) closer to your listening position.
• R. D. 3.4 m (12 ft) (rear speakers distance)
Rear speaker distance can be set in 0.2 meter (1.0 foot) steps from a distance equal to the front
speaker distance to a distance 4.6 meters (15.0 feet) closer to your listening position.
Note
If each of the front or rear speakers are not placed an equal distance from your listening position, set the distance
of the closest speaker.
Specifying the rear speaker position and height
If you select anything other than “NO” in “R.SP.,” specify the position and height of the rear
speakers. The default settings are underlined.
Position diagram
90
A
A
45
B
B
20
• R. P. BEHIND
Select this if the rear speakers are located in the section B.
• R. P. SIDE
Select this if the rear speakers are located in the section A.
continued
25GB
Height diagram
C
C
60
D
D
30
• R. H. LOW
Select this if the rear speakers are located in section D.
• R. H. HIGH
Select this if the rear speakers are located in section C.
These parameters are not available when “R.SP.“ is set to “NO”.
To specify the balance and level of the speakers
1
2
Press AMP MENU repeatedly to display 9 LEVEL on the front panel display.
3
Sit in your listening position and select the item to be adjusted using X/x.
• Items adjusted in 9 LEVEL
– Balance of the front and rear speakers
– Volume level of the centre and rear speakers and subwoofer
4
Adjust the volume level so that the volume of the test tone from each speaker sounds the
same using C/c.
The adjusted value will appear on the front panel display.
5
Repeat Steps 3 and 4 to adjust other parameters in 9 LEVEL.
If you do not operate the remote for a few seconds, the value disappears from the display
and is stored in the receiver.
6
Use X/x to select T.TONE and use C/c to set T.TONE to OFF.
Use X/x to select T.TONE and use C/c to set T.TONE to ON.
You will hear the test tone from each speaker in sequence.
xBALANCE
You can vary the balance of each speaker as follows. The default settings are underlined.
• F. ......I...... centre (front speakers)
Adjust the balance between the front left and right speakers (You can adjust from centre,
6 steps left or right).
• R. ......I...... centre (rear speakers)
Adjust the balance between the rear left and right speakers (You can adjust from centre,
6 steps left or right).
26GB
Notes
• When you select an item, the sound cuts off for a moment.
• Depending on the settings of other speakers, the subwoofer may output excessive sound.
To adjust the volume of all the speakers at one time
Use the VOLUME control.
Getting Started
xLEVEL
You can vary the level of each speaker as follows. The default settings are underlined.
• C. LEVEL 0 dB (centre speaker level)
Adjust the level of the centre speaker (you can adjust from –10 dB to +10 dB in 1 dB steps).
• R. LEVEL 0 dB (rear speakers level)
Adjust the level of the rear speakers (you can adjust from –10 dB to +10 dB in 1 dB steps).
• SW. LEV. 0 dB (subwoofer level)
Adjust the level of the subwoofer (you can adjust from –10 dB to +10 dB in 1 dB steps).
Other AMP MENU settings
You can control the brightness of the front panel display, clear the preset stations and the station
names, and set the speaker parameters back to the default setting. Press AMP MENU repeatedly
to display 9 CUSTOMIZE. Use X/x to select the following items.
xDIMMER
You can change the brightness of the front panel display by two ways. Use C/c to adjust the
settings or press DIMMER.
xMEMO. CLR.
You can clear the preset stations and station names, and set the speaker parameters back to the
default setting.
• MEMO.CLR.N (No): Press ENTER to skip back to previous menu.
• MEMO.CLR.Y (Yes): If you press ENTER, “Really? N” appears. To clear the memory, use
C/c to select “Really? Y” and press ENTER. “ALL CLEAR!” is displayed and all settings
such as preset stations and station names will be cleared, and speaker parameters will be reset
to their default settings.
27GB
Presetting Radio Stations
You can preset 20 stations for FM and 10 stations for AM.
Before tuning, make sure to turn down the volume to minimum.
BAND
MEMORY
PRESET +/–
m/M
ENTER
1 Press BAND repeatedly until the band you want appears on the front panel
display.
Every time you press BAND, the band changes to AM or FM alternately.
2 Press and hold m or M until the frequency indication starts to change,
then release.
Scanning stops when the receiver tunes in a station. “TUNED” and “ST” (for stereo
programme) appear on the front panel display.
ALL 1 DISC S AUTO TITLE
PRO LOGIC
DIGITAL FM AM
NTSC PBC ANGLE
TRACK
CHAPTER INDEX
H TUNED
M MONO ST S
dB REPEAT 1
k H z PROGRAM
M H z SHUFFLE
3 Press MEMORY.
A preset number appears on the front panel display.
ALL 1 DISC S AUTO TITLE
PRO LOGIC
DIGITAL FM AM
NTSC PBC ANGLE
TRACK
CHAPTER INDEX
H TUNED
M MONO ST S
dB REPEAT 1
k H z PROGRAM
M H z SHUFFLE
4 Press PRESET + or – to select the preset number you want.
ALL 1 DISC S AUTO TITLE
PRO LOGIC
DIGITAL FM AM
NTSC PBC ANGLE
28GB
TRACK
CHAPTER INDEX
H TUNED
M MONO ST S
dB REPEAT 1
k H z PROGRAM
M H z SHUFFLE
5 Press ENTER.
The station is stored.
ALL 1 DISC S AUTO TITLE
PRO LOGIC
DIGITAL FM AM
NTSC PBC ANGLE
TRACK
ALL 1 DISC S AUTO TITLE
PRO LOGIC
DIGITAL FM AM
NTSC PBC ANGLE
TRACK
CHAPTER INDEX
H TUNED
M MONO ST S
dB REPEAT 1
k H z PROGRAM
M H z SHUFFLE
H TUNED
M MONO ST S
dB REPEAT 1
k H z PROGRAM
M H z SHUFFLE
6 Repeat 1 to 5 to store other stations.
To tune in a station with a weak signal
Press m or M repeatedly in 2 to tune in the station manually.
Getting Started
v
CHAPTER INDEX
To change the preset number
Start over from 1.
29GB
Playing Discs
4
Playing Discs
Press A on the receiver or OPEN/
CLOSE on the remote, and place a
disc on the disc tray.
The receiver automatically turns on
and the STANDBY indicator turns off.
Depending on the DVD or VIDEO CD,
some operations may be different or
restricted.
Refer to the operating instructions supplied
with your disc.
STANDBY
indicator
A
H x
With the playback side facing down
PHONES
Adjust the volume
Connect
headphones
POWER
OPEN/
CLOSE
H
1
2
3
Press H.
The disc tray closes, and the receiver
starts playback (continuous play).
Adjust the volume on the receiver.
[/1
After following Step 5
Depending on the disc, a menu may appear
on the TV screen. You can play the disc
interactively by following the instructions
on the menu. DVD (page 32), VIDEO CD
(page 33).
x
Turn on your TV.
Switch the input selector on the TV
to this receiver.
Press POWER on the receiver.
The receiver enters standby mode and
the STANDBY indicator lights up in
red.
30GB
5
To turn on the receiver
Press POWER on the receiver. The receiver
enters standby mode and the STANDBY
indicator lights up in red. Press [/1 on the
remote. The receiver turns on and the
STANDBY indicator turns off. In standby
mode, you can also turn on the receiver by
pressing A on the receiver or by pressing
H.
To turn off the receiver
Press [/1 on the remote. The receiver
enters standby mode and the STANDBY
indicator lights up in red. To turn off the
receiver completely, press POWER on the
receiver. While playing a disc, do not turn
off the receiver by pressing POWER. Doing
so may cancel the menu settings. When you
turn off the receiver, first press x to stop
playback and then press [/1 on the remote.
Saving the power in standby mode
Press [/1 on the remote once.
z While the receiver is in standby mode, the
STANDBY indicator on the receiver lights up.
Resuming Playback from
the Point Where You
Stopped the Disc (Resume Play)
To cancel standby mode
Press [/1 on the remote once.
OPEN/CLOSE
H
Playing Discs
When you stop the disc, the receiver
remembers the point where you pressed x
and “RESUME” appears on the front panel
display. As long as you do not open the disc
tray, Resume Play will work even if the
receiver enters standby mode by pressing
[/1.
Additional operations
x
./>
H
x
X
To
Stop
Pause
Resume play after
pause
Go to the next chapter,
track, or scene in
continuous play mode
Go back to the
preceding chapter, track,
or scene in continuous
play mode
Stop play and remove
the disc
Mute the sound
MUTING
Operation
Press x.
Press X.
Press X or H.
1
Press >.
“RESUME” appears on the front panel
display, so you can restart the disc
from the point where you stopped the
disc.
If “RESUME” does not appear,
Resume Play is not available.
Press ..
Press OPEN/CLOSE.
Press MUTING. To
cancel muting, press it
again or turn up the
volume.
Note
While playing a disc, press x to
stop playback.
2
Press H.
The receiver starts playback from the
point where you stopped the disc in
Step 1.
z To play from the beginning of the disc, press x
twice, then press H.
Do not push the disc tray when closing it. Press
OPEN/CLOSE to close the disc tray.
continued
31GB
Notes
• Depending on where you stopped the disc, the
receiver may not resume playback from exactly the
same point.
• The point where you stopped playing is cleared
when:
– you turn the power off by pressing POWER on
the receiver.
– you change the play mode.
Using the DVD’s Menu
A DVD is divided into long sections of a
picture or a music feature called “titles.”
When you play a DVD which contains
several titles, you can select the title you
want using DVD TOP MENU.
When you play DVDs that allow you to
select items such as the language for the
subtitles and the language for the sound,
select these items using DVD MENU.
Number
buttons
DVD TOP
MENU
DVD MENU
ENTER
C/X/x/c
32GB
1
Press DVD TOP MENU or DVD MENU.
The disc’s menu appears on the TV
screen.
The contents of the menu vary from disc
to disc.
2
Press C/X/x/c or the number buttons
to select the item you want to play or
change.
3
Press ENTER.
Playing VIDEO CDs with
PBC Functions (PBC Playback)
z To play without using PBC, press ./> or
the number buttons while the receiver is stopped to
select a track, then press H or ENTER.
“Play without PBC” appears on the TV screen and
the receiver starts continuous play. You cannot play
still pictures such as a menu. To return to PBC
playback, press x twice, then press H.
Note
Depending on the VIDEO CD, “Press ENTER” in
Step 3 may appear as “Press SELECT” in the
instructions supplied with the disc. In this case, press
H.
Playing Discs
With PBC (Playback Control) functions,
you can enjoy simple interactive operations,
search functions, and other such operations.
PBC playback allows you to play VIDEO
CDs interactively by following the menu on
the TV screen.
To go back to the menu
Press O RETURN.
Number
buttons
./>
H
x
ENTER
X/x
O RETURN
1
Start playing a VIDEO CD with PBC
functions.
The menu for your selection appears.
2
3
4
Select the item number you want
by pressing X/x or the number
buttons.
Press ENTER.
Follow the instructions in the
menu for interactive operations.
Refer to the instructions supplied with
the disc, as the operating procedure
may differ according to the VIDEO
CD.
33GB
Creating Your Own
Programme (Programme Play)
2
Press c.
The cursor moves to the title or track
(in this case, “01”).
Title
PROGRAM
ALL CLEAR
1. TITLE – –
2. TITLE – –
3. TITLE – –
4. TITLE – –
5. TITLE – –
6. TITLE – –
7. TITLE – –
You can play the contents of a disc in the
order you want by arranging the order of the
titles, chapters or tracks on the disc to create
your own programme. You can programme
up to 25 titles, chapters, and tracks.
Chapter
T
C
––
01
02
03
04
05
ALL
01
02
03
04
05
06
Chapters recorded on a disc
PLAY MODE
REPEAT
3
Number
buttons
CLEAR
Select the title, chapter, or track
you want to programme.
xWhen playing a DVD
For example, select chapter “03” of
title “02.”
Press X/x or the number buttons to
select “02” under “T,” then press
ENTER.
H
ENTER
X/x/c
PROGRAM
1
In stop mode, press PLAY MODE
repeatedly until “PROGRAM”
appears on the front panel
display.
The programming display appears on
the TV screen.
“TRACK” is displayed when you play a
VIDEO CD, Super Audio CD, or CD.
PROGRAM
ALL CLEAR
1. TITLE
2. TITLE – –
3. TITLE – –
4. TITLE – –
5. TITLE – –
6. TITLE – –
7. TITLE – –
T
––
01
02
03
04
05
ALL CLEAR
1. TITLE – –
2. TITLE – –
3. TITLE – –
4. TITLE – –
5. TITLE – –
6. TITLE – –
7. TITLE – –
T
C
––
01
02
03
04
05
ALL
01
02
03
04
05
06
Next, press X/x or the number buttons
to select “03” under “C,” then press
ENTER.
PROGRAM
ALL CLEAR
1. TITLE 0 2 – 0 3
2. TITLE – –
3. TITLE – –
4. TITLE – –
5. TITLE – –
6. TITLE – –
7. TITLE – –
T
––
01
02
03
04
05
Titles or tracks
recorded on a disc
Selected title and chapter
34GB
xWhen playing a VIDEO CD,
Super Audio CD, or CD
For example, select track “02.”
Press X/x or the number buttons to
select “02” under “T,” then press
ENTER.
To cancel the programmed order
To cancel all the titles, chapters, or tracks in
the programmed order, press X, and select
“ALL CLEAR” in Step 2. To cancel the
selected programme, select the programme
using X/x in Step 2, then press CLEAR, or
select “--” in Step 3, then press ENTER.
Selected track
z You can do Repeat Play of the programmed titles,
ALL CLEAR
1. TRACK 0 2
2. TRACK – –
3. TRACK – –
4. TRACK – –
5. TRACK – –
6. TRACK – –
7. TRACK – –
0:15:30
T
––
01
02
03
04
05
chapters, or tracks. Press REPEAT, or set “REPEAT”
to “ON” in the Control Menu display during
Programme Play.
Note
The number of titles, chapters, or tracks displayed are
the same number of titles, chapters, or tracks
recorded on a disc.
Playing Discs
PROGRAM
Total time of the programmed tracks
4
To programme other titles,
chapters, or tracks, repeat Steps 2
to 3.
The programmed titles, chapters, and
tracks are displayed in the selected
order.
5
Press H to start Programme
Play.
Programme Play begins.
When the programme ends, you can
restart the same programme again by
pressing H.
To return to normal play
Press CLEAR during playback.
To turn off the programme menu
In stop mode, press PLAY MODE to turn
off the programme menu.
To change the programme
1
In Step 2, select the programme number
of the title, chapter, or track you want to
change using X/x or the number
buttons, and press c.
2
Follow Step 3 for new programming.
35GB
Playing in random order
Playing repeatedly (Repeat
(Shuffle Play)
Play)
You can have the receiver “shuffle” titles,
chapters, or tracks and play them in random
order. Subsequent “shuffling” may produce
a different playing order.
You can play all the titles/tracks or a single
title/chapter/track on a disc.
In Shuffle or Programme Play mode, the
receiver repeats the titles or tracks in the
shuffled or programmed order.
You cannot perform Repeat Play during
PBC playback of VIDEO CDs (page 33).
You may not be able to perform Repeat Play
depending on the DVD.
PLAY MODE
CLEAR
H
PLAY MODE
REPEAT
CLEAR
H
1
2
In stop mode, press PLAY MODE
repeatedly until “SHUFFLE”
appears on the front panel
display.
DVD DISPLAY
Press H.
To return to normal play
In stop mode, press PLAY MODE twice, or
during playback, press CLEAR to return to
normal play.
Notes
• Shuffle Play is cancelled when:
– you open or close the disc tray
– you turn the power off
– you change the function
• You may not be able to do Shuffle Play depending
on the DVD.
36GB
ENTER
X/x
1
Press DVD DISPLAY.
The Control Menu appears.
2
Press X/x to select
(REPEAT), then press ENTER.
If you do not select “OFF,” the
indicator of “REPEAT” lights up in
green.
3
Select the Repeat Play setting.
12(27)
18(34)
T
1:32:55
DVD
OFF
OFF
DISC
TITLE
CHAPTER
Playing Discs
When playing a DVD and when
Programme Play is set to OFF
• OFF: does not play repeatedly.
• DISC: repeats all the titles.
• TITLE: repeats the current title on a disc.
• CHAPTER: repeats the current chapter.
When playing a VIDEO CD/Super
Audio CD/CD and when Programme
Play is set to OFF
• OFF: does not play repeatedly.
• DISC: repeats all the tracks on a disc.
• TRACK: repeats the current track
When Programme Play is set to ON
• OFF: does not play repeatedly.
• ON: repeats Programme Play.
To cancel Repeat Play
Press CLEAR.
z You can set Repeat Play during stop
mode
After selecting the “REPEAT” item, press H.
The receiver starts Repeat Play.
z You can quickly display the “REPEAT”
status
Press REPEAT on the remote.
Note
Repeat play is cancelled when:
– you turn the power off.
– you change the function.
37GB
Searching for a Scene
Searching for a Particular
Point on a Disc (Scan, Slowmotion Play)
You can locate a particular point on a disc
quickly by monitoring the picture or playing
back slowly.
m/M
H
Watching frame by frame (Slowmotion play)
You can use this function only for DVDs or
VIDEO CDs. Press m or M when the
receiver is in the pause mode. To return to
normal speed, press H.
Each time you press m or M during
Slow-motion play, the playback speed
changes. Two speeds are available. With
each press, the indication changes as
follows:
Playback direction
SLOW 2M y SLOW 1M
Opposite direction (DVD only)
SLOW 2m y SLOW 1m
Note
Depending on the DVD/VIDEO CD, you may not be
able to do some of the operations described.
Locating a point quickly by playing
a disc in fast forward or fast
reverse (Scan)
Press m or M while playing a disc.
When you find the point you want, press
H to return to normal speed.
Each time you press m or M during
scan, the playback speed changes. Three
speeds are available. With each press, the
indication changes as follows:
t
Playback direction
×2B (DVD/Super Audio CD/CD only) t FF1M
FF2M T
t
Opposite direction
×2b (DVD only) t FR1m t FR2m
The ×2B/×2b playback speed is about twice
the normal speed. The FF2M/FR2m
playback speed is faster than FF1M/
FR1m.
38GB
The SLOW 2M/SLOW 2m playback
speed is slower than SLOW 1M/SLOW
1m.
xWhen playing a VIDEO CD with
PBC Playback
(SCENE)
Searching for a Title/
Chapter/Track/Index/
Scene
xWhen playing a Super Audio
CD/CD
(TRACK) or
(INDEX)
You can search a DVD disc by title or
chapter, and you can search a VIDEO CD or
CD by track, index, or scene. As titles and
tracks are assigned unique numbers on the
disc, you can select the desired one by
entering its number. Or, you can search for a
scene using the time code. (TIME SEARCH)
12(27)
18(34)
T
1:32:55
Number
buttons
Searching for a Scene
Example: when you select
(CHAPTER)
“** (**)” is selected (** refers to a
number).
The number in parentheses indicates
the total number of titles, chapters,
tracks, indexes, or scenes.
DVD
CLEAR
Selected row
ENTER
X/x
DVD DISPLAY
3
Press ENTER.
“** (**)” changes to “— (**)”.
12(27)
– –(34)
T
1:32:55
1
DVD
Press DVD DISPLAY.
The Control Menu appears.
2
Press X/x to select the search
method.
xWhen playing a DVD
(TITLE),
(CHAPTER), or
(TIME/TEXT)
Select TIME/TEXT for TIME
SEARCH.
xWhen playing a VIDEO CD
(TRACK) or
(INDEX)
4
Press X/x or the number buttons
to select the title, chapter, track,
index, or scene number you want
to search.
If you make a mistake
Cancel the number by pressing
CLEAR, then select another number.
continued
39GB
5
Press ENTER.
The receiver starts playback from the
selected number.
To turn off the Control Menu
Press DVD DISPLAY repeatedly until the
Control Menu is turned off.
To search for a scene using the time
code (TIME SEARCH) (DVD only)
1
In Step 2, select
(TIME/
TEXT).
“T **:**:**” (playing time of the
current title) is selected.
2
Press ENTER.
“T **:**:**” changes to “T --:--:--.”
3
Input the time code using the number
buttons, then press ENTER.
For example, to find the scene at
2 hours, 10 minutes, and 20 seconds
after the beginning, just enter “2:10:20.”
Note
The title, chapter or track number displayed is the
same number recorded on the disc.
40GB
Viewing Information About the Disc
Viewing the Playing Time
and Remaining Time on
the Front Panel Display
When playing a DVD
Playing time and number of the current title
TITLE
TRACK
CHAPTER INDEX
H TUNED
M MONO ST S
dB REPEAT 1
k H z PROGRAM
M H z SHUFFLE
Remaining time of the
current title
TITLE
TRACK
CHAPTER INDEX
H TUNED
M MONO ST S
dB REPEAT 1
k H z PROGRAM
M H z SHUFFLE
You can check information about the disc,
such as the remaining time, total number of
titles of a DVD, or tracks of a Super Audio
CD, CD, or VIDEO CD, using the front
panel display (page 10).
Playing time and number
of the current chapter
TITLE
TRACK
CHAPTER INDEX
H TUNED
M MONO ST S
dB REPEAT 1
k H z PROGRAM
M H z SHUFFLE
Remaining time of the
current chapter
TRACK
CHAPTER INDEX
H TUNED
M MONO ST S
Viewing Information About the Disc
TITLE
dB REPEAT 1
k H z PROGRAM
M H z SHUFFLE
TIME
Text
TITLE
TRACK
CHAPTER INDEX
H TUNED
M MONO ST S
dB REPEAT 1
k H z PROGRAM
M H z SHUFFLE
When playing a VIDEO CD (without
PBC functions), Super Audio CD, or
CD
Playing time and current track number
TITLE
TRACK
CHAPTER INDEX
H TUNED
M MONO ST S
dB REPEAT 1
k H z PROGRAM
M H z SHUFFLE
Press TIME.
Each time you press TIME while playing the
disc, the display changes as shown in the
following charts.
Remaining time of the
current track
TITLE
TRACK
CHAPTER INDEX
H TUNED
M MONO ST S
dB REPEAT 1
k H z PROGRAM
M H z SHUFFLE
Playing time of the disc
TITLE
TRACK
CHAPTER INDEX
H TUNED
M MONO ST S
dB REPEAT 1
k H z PROGRAM
M H z SHUFFLE
Remaining time of the
disc
TITLE
TRACK
CHAPTER INDEX
H TUNED
M MONO ST S
dB REPEAT 1
k H z PROGRAM
M H z SHUFFLE
Text
TITLE
TRACK
CHAPTER INDEX
H TUNED
M MONO ST S
dB REPEAT 1
k H z PROGRAM
M H z SHUFFLE
continued
41GB
z When playing VIDEO CDs with PBC functions,
the scene number and the playing time are displayed.
z The playing time and remaining time of the
current chapter, title, track, scene, or disc will also
appear on your TV screen. See the following section
“Checking the Playing Time and Remaining Time”
for instructions on how to read this information.
Notes
• While playing Super Audio CD, the index indicator
does not appear on the front panel display.
• Depending on the type of disc being played and the
playing mode, the disc information may not be
displayed.
Checking the Playing
Time and Remaining Time
You can check the playing time and
remaining time of the current title, chapter,
or track, and the total playing time or
remaining time of the disc. You can also
check the DVD/CD/Super Audio CD text
recorded on the disc.
TIME
DVD
DISPLAY
1
Press DVD DISPLAY during
playback.
The Control Menu appears.
12(27)
18(34)
T
1:32:55
DVD
Disc type
Time information
42GB
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement