Yamaha R-V901
RX-V901
Natural Sound Stereo Receiver
Thank you for selecting this YAMAHA stereo receiver.
OWNER’S MANUAL
CAUTION
RISK OF ELECTRIC
SHOCK
CONTENTS
Safety Instructions ................... 2
Features ................................... 4
Supplied Accessories .............. 4
Profile of This Unit .................... 5
Speaker Setup for
This Unit.................................... 6
Connections ............................. 7
Speaker Balance Adjustment ... 12
Basic Operations .................... 15
Tuning Operations .................. 18
Preset Tuning ...........................19
Using Digital Sound Field
Processor (DSP) .................... 22
Setting the SLEEP Timer ....... 26
Remote Control Transmitter ... 27
Troubleshooting ...................... 33
Specifications ......................... 34
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK), NO USER-SERVICEABLE
PARTS INSIDE, REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
IMPORTANT!
Please record the serial number of this
unit in the space below.
• Explanation of Graphical Symbols
Serial No.:
The serial number is located on the rear
of the unit.
Retain this Owner’s Manual in a safe
place for future reference.
WARNING
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.
The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert you to the
presence of uninsulated “dangerous
voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert
you to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.
SAFETY INSTRUCTIONS
1
Read Instructions – All the safety and operating
instructions should be read before the unit is operated.
A. The power-supply cord or the plug has been damaged;
Retain Instructions – The safety and operating instructions
should be retained for future reference.
B. Objects have fallen, or liquid has been spilled into the unit;
3
Heed Warnings – All warnings on the unit and in the
operating instructions should be adhered to.
C. The unit has been exposed to rain; or
4
Follow Instructions – All operating and other instructions
should be followed.
5
Water and Moisture – The unit should not be used near
water – for example, near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming
pool, etc.
2
6
or
or
D. The unit does not appear to operate normally or exhibits a
marked change in performance; or
E. The unit has been dropped, or the cabinet damaged.
Carts and Stands – The unit should be used only with a
cart or stand that is recommended by the manufacturer.
6A A unit and cart combination should
be moved with care. Quick stops,
excessive force, and uneven
surfaces may cause the unit and
cart combination to overturn.
7
Wall or Ceiling Mounting – The unit
should be mounted to a wall or ceiling only as
recommended by the manufacturer.
8
Ventilation – The unit should be situated so that its
location or position does not interfere with its proper
ventilation. For example, the unit should not be situated
on a bed, sofa, rug, or similar surface, that may block the
ventilation openings; or placed in a built-in installation,
such as a bookcase or cabinet that may impede the flow
of air through the ventilation openings.
9
Heat – The unit should be situated away from heat
sources such as radiators, stoves, or other appliances that
produce heat.
16 Servicing – The user should not attempt to service the unit
beyond those means described in the operating
instructions. All other servicing should be referred to
qualified service personnel.
17 Power Lines – An outdoor antenna should be located
away from power lines.
18 Grounding or Polarization – Precautions should be taken
so that the grounding or polarization is not defeated.
19 Outdoor Antenna Grounding – If an outside antenna is
connected to this unit, be sure the antenna system is
grounded so as to provide some protection against voltage
surges and built-up static charges. Article 810 of the
National Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to
an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to
grounding electrodes, and requirements for the grounding
electrode.
EXAMPLE OF ANTENNA GROUNDING
MAST
10 Power Sources – The unit should be connected to a power
supply only of the type described in the operating
instructions or as marked on the unit.
GROUND
CLAMP
11 Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the unit.
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810–20)
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810–21)
GROUND CLAMPS
12 Cleaning – The unit should be cleaned only as
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250. PART H)
recommended by the manufacturer.
13 Nonuse Periods – The power cord of the unit should be
ANTENNA
LEAD IN
WIRE
NEC – NATIONAL ELECTRICAL CODE
unplugged from the outlet when left unused for a long
period of time.
Note to CATV system installer:
14 Object and Liquid Entry – Care should be taken so that
objects do not fall into and liquids are not spilled into the
inside of the unit.
15 Damage Requiring Service – The unit should be serviced
by qualified service personnel when:
2
This reminder is provided to call the CATV system
installer's attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building, as
close to the point of cable entry as practical.
Caution: Read this before operating your unit
1
2
3
4
5
To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
Install this unit in a cool, dry, clean place – away from
windows, heat sources, sources of excessive vibration,
dust, moisture and cold. Avoid sources of humming
(transformers, motors). To prevent fire or electrical
shock, do not expose the unit to rain or water.
Do not operate the unit upside-down. It may overheat,
possibly causing damage.
Never open the cabinet. If something drops into the set,
contact your dealer.
Do not use force on switches, controls or connection
wires. When moving the unit, first disconnect the power
plug and the wires connected to other equipment.
Never pull the wires themselves.
6
7
8
9
10
Do not attempt to clean the unit with chemical solvents;
this might damage the finish. Use a clean, dry cloth.
Always set the VOLUME control to “– ∞” before starting
the audio source play. Increase the volume gradually to
an appropriate level after the play back has been
started.
To prevent lightning damage, pull out the power cord
and remove the antenna cable during an electrical
storm.
Be sure to read the “TROUBLESHOOTING” section
regarding common operating errors before concluding
that the unit is faulty.
AC outlet
Do not connect audio equipment to the AC outlet on the
rear panel if that equipment requires more power than
the outlet is rated to provide.
FCC INFORMATION
1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to
use the product.
2. IMPORTANT : When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product
MUST be used. Follow all installation instructions.
Failure to follow instructions could void your FCC
authorization to use this product in the USA.
3. NOTE : This product has been tested and found to
comply with the requirements listed in FCC Regulations,
Part 15 for Class “B” digital devices. Compliance with
these requirements provides a reasonable level of
assurance that your use of this product in a residential
environment will not result in harmful interference with
other electronic devices.
This equipment generates/uses radio frequencies and, if
not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic devices.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this product
is found to be the source of interference, which can be
determined by turning the unit “OFF” and “ON”, please try
to eliminate the problem by using one of the following
measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
We Want You Listening For A Lifetime
YAMAHA and the Electronic Industries Association’s
Consumer Electronics Group want you to get the most out of
your equipment by playing it at a safe level. One that lets the
sound come through loud and clear without annoying blaring or
distortion – and, most importantly, without
affecting your sensitive hearing. Since hearing
damage from loud sounds is often undetectable
until it is too late, YAMAHA and the Electronic
Industries Association’s Consumer Electronics
Group recommend you to avoid prolonged
exposure from excessive volume levels.
3
FEATURES
●
5 Speaker Configuration
●
Test Tone Generator for Easier Speaker Output
Balance Adjustment
●
3 Center Channel Modes
(NORMAL/WIDE/PHANTOM)
●
40-Station Random Access Preset Tuning
●
Automatic Preset Tuning
Digital Sound Field Processor
6 Programs for Digital Sound Field Processing
2 Programs for Dolby Surround Decoding
(DOLBY PRO LOGIC and DOLBY PRO LOGIC
ENHANCED)
●
Preset Station Shifting Capability
(Preset Editing)
●
IF Count Direct PLL Synthesizer Tuning System
●
Video Signal Input/Output Capability
Automatic Input Balance Control for Dolby
Surround
●
SLEEP Timer
●
Remote Control Capability
Front:
85W + 85W (8Ω) RMS Output Power,
0.07% THD, 1 kHz
Center: 85W (8Ω) RMS Output Power,
0.07% THD, 1 kHz
Rear:
20W + 20W (8Ω) RMS Output Power,
0.3% THD, 1 kHz
●
●
SUPPLIED ACCESSORIES
After unpacking, check that the following parts are contained.
Remote Control Transmitter
<U.S.A., Canada
and Australia models>
4
Batteries (size AA, R6, UM-3)
Indoor FM Antenna
User Program Sheets
AM Loop Antenna
<General model>
PROFILE OF THIS UNIT
You are the proud owner of a Yamaha stereo receiver –an extremely sophisticated audio component. The Digital Sound Field
Processor (DSP) built into this unit takes full advantage of Yamaha’s undisputed leadership in the field of digital audio processing to
bring you a whole new world of listening experiences. Follow the instructions in this manual carefully when setting up your system,
and this unit will sonically transform your room into a wide range of listening environments –movie theater, concert hall, and so on.
In addition, you get incredible realism from Dolby-encoded video sources using the built-in Dolby Pro Logic Surround Decoder.
Please read this operation manual carefully and store it in a safe place for later reference.
Digital Sound Field Processing
What is it that makes live music so good? Today’s advanced
sound reproduction technology lets you get extremely close to
the sound of a live performance, but chances are you’ll still
notice something missing: the acoustic environment of the live
concert hall. Extensive research into the exact nature of the
sonic reflections that create the ambience of a large hall has
made it possible for Yamaha engineers to bring you this same
sound in your own listening room, so you’ll feel all the sound of
a live concert.
What’s more, our technicians, armed with sophisticated
measuring equipment, have even made it possible to capture
the acoustics of a variety of venues such as an actual concert
hall, theater, etc. to allow you to accurately recreate one of
several actual live performance environments, all in your own
home.
Dolby Pro Logic Surround
The Dolby Pro Logic Surround Decoder program lets you
experience the dramatic realism and impact of Dolby Surround
movie theater sound in your own home. Dolby Pro Logic gets
its name from its professional-grade steering logic circuitry,
which provides greater effective front and rear channel
separation for a much higher degree of realism than the
“passive” Dolby Surround circuits found in less sophisticated
home audio/video equipment. Dolby Pro Logic Surround
provides a true center channel, so that there are four
independent channels, unlike passive Dolby Surround which
has in effect only three channels: left, right, and rear. This
center channel allows listeners seated in even less-than-ideal
positions to hear the dialog originating from action on the
screen while getting a stereo effect as well.
This Dolby Pro Logic Surround Decoder employs a digital
signal processing system. This system increases sound
stability at each channel and minimizes crosstalk between
channels compared to conventional analog Dolby signal
processing.
In addition, this unit features a built-in automatic input balance
control. This circuit always presents you the best surround
conditions without performing manual adjustments.
Dolby Pro Logic Surround + DSP
You can also enjoy a combination of Dolby Pro Logic Surround
and DSP in the sound field program “
PRO LOGIC
ENHANCED”.
It recreates the surround effect of a movie theater, effectively
duplicating its multiple surround loudspeaker system,
completely surrounding the listener with the sounds of the
action taking place on the screen.
5
SPEAKER SETUP FOR THIS UNIT
SPEAKERS TO BE USED
This unit is designed to provide the best sound-field quality with a 5 speaker configuration. The speakers to be used with this unit
will be mainly front speakers, rear speakers, and a center speaker. (You can omit the center speaker. Refer to the “4-Speaker
Configuration” shown below.)
The front speakers are used for the main source sound and the effect sound. They will probably be the speakers of your present
stereo speaker system. The rear speakers are used for the effect sound. And the center speaker is used for the center sound
(dialog etc.) encoded with the Dolby Surround. The rear and center speakers do not need to be equal in power to the front
speakers. However, all the speakers should have high enough power handling to accept the maximum output of this unit.
SPEAKER CONFIGURATION
5-Speaker Configuration
4-Speaker Configuration
This configuration is the most effective and recommended one.
In this configuration, the center speaker is necessary as well as
the rear speakers. If the digital sound field program DOLBY
PRO LOGIC or DOLBY PRO LOGIC ENHANCED is selected,
conversations will be output from the center speaker and the
ambience will be excellent.
● Set the center channel mode to the “NORMAL” or “WIDE”
position. (For details, refer to page 13.)
The center speaker is not used in this configuration. If the
digital sound field program DOLBY PRO LOGIC or DOLBY
PRO LOGIC ENHANCED is selected, the center sound is
output from the left and the right front speakers. However, the
sound effect of other programs can be the same as that of the
5-speaker configuration.
● Be sure to set the center channel mode to the “PHANTOM”
position. (For details, refer to page 13.)
Front L
Center
Front R
Front L
Dialogue
Dialogue
Surround sound
Surround sound
Rear L
Rear R
Rear L
Front R
Rear R
SPEAKER PLACEMENT
The recommended speaker configuration, the 5-speaker configuration, will require two speaker pairs: front speakers (your normal
stereo speakers), and rear speakers, plus a center speaker. When you place these speakers, refer to the following.
Front:
In normal position. (The position of your present
stereo speaker system.)
Rear: Behind your listening position, facing slightly inward.
Nearly six feet (approx. 1.8 m) up from the floor.
Center: Precisely between the front speakers. (To avoid
interference with TV sets, use a magnetically shielded
speaker.)
Front R
Center
Front L
TV set
Rear R
Rear L
6
CONNECTIONS
Before attempting to make any connections to or from this unit, be sure to first switch OFF the power to this unit and to any other
components to which connections are being made.
CONNECTIONS WITH OTHER COMPONENTS
When making connections between this unit and other components, be sure all connections are made correctly, that is to say L (left)
to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the owner’s manual for each component to be connected to this unit.
LD player,
TV tuner, etc.
AUDIO IN
VIDEO OUT
AUDIO OUT
VIDEO IN
Video cassette recorder 2
VIDEO OUT
VIDEO IN
AUDIO OUT
Monitor TV
GND
OUTPUT
Turntable
(U.S.A. model)
OUTPUT
8ΩMIN.
/SPEAKER
FRONT
CENTER
REAR
REAR
GND
75Ω UNBAL.
AC OUTLETS
CENTER
FM
ANT
C
SWITCHED
I20W MAX. TOTAL
l20W MAX. TOTAL
I.0A MAX. TOTAL
D
DUAL
C D:4ΩMIN./SPEAKER
SINGLE:8ΩMIN./SPEAKER
VIDEO SIGNAL
GND
MONITOR LD/TV
OUT
IN
VCR 1
OUT
IN
VCR 2
OUT
LOW
PASS
fc:200Hz
SINGLE
MAINS
SPEAKERS
SPEAKERS
AM
ANT
A
A
A OR B:8ΩMIN.
/SPEAKER
A B:l6ΩMIN.
/SPEAKER
B
PHONO
CD
TAPE
REC
PB
OUT
TAPE
IN
LD/TV
OUT
VCR 1
IN
B
OUT
VCR 2
FRONT
AUDIO SIGNAL
CD player
Tape deck
VIDEO IN
AUDIO IN
AUDIO OUT
VIDEO OUT
LINE IN
OUTPUT
LINE OUT
To AC outlet
Video cassette recorder 1
: Refer to “ABOUT THE
ACCESSORY TERMINALS”
on page 10.
CONNECTING TO VIDEO AUX TERMINALS (ON THE FRONT PANEL)
These terminals are used to connect any video input source such as a camcorder to this unit.
VIDEO AUX
VIDEO
L AUDIO R
AUDIO OUT R
AUDIO OUT L
VIDEO OUT
R
L
VIDEO
Camcorder
7
CONNECTING SPEAKERS
Connect the respective speakers to this unit as figured below.
Rear speakers
Left
Right
OUTPUT
8ΩMIN.
/SPEAKER
FRONT
CENTER
REAR
REAR
CENTER
C
D
DUAL
C D:4ΩMIN./SPEAKER
SINGLE:8ΩMIN./SPEAKER
Center speaker
LOW
PASS
fc:200Hz
SINGLE
SPEAKERS
SPEAKERS
A
A
B
B
FRONT
Left
Right
Left
Right
Front speakers A
Front speakers B
Note on front speaker connection:
One or two speaker systems can be connected to this unit. If
you connect only one speaker system, connect it to either the
SPEAKERS A or B terminals.
IMPEDANCE SELECTOR switch
(Canada model only)
Be sure to switch this only when the power of this unit is
turned off. Select the position proper for the use of your front
speakers.
Note on center speaker connection:
One or two center speakers can be connected to this unit. If
you cannot place the center speaker on or under the TV, it is
recommended to use two center speakers and place them on
both sides of the TV to orient the center sound at the center
position.
For connecting two center speakers, follow the method shown
below.
When using one pair of front
speakers;
• If the impedance of each speaker is
8Ω or higher, set to right (
).
• If the impedance of each
speaker is 4Ω or higher, but lower
than 8Ω, set to left (
).
A OR B:USE 4ΩMIN.
/SPEAKER
A
B:USE 8ΩMIN.
/SPEAKER
A OR B:USE 8ΩMIN.
/SPEAKER
When using two pairs of front
speakers;
The impedance of each speaker must
be 8Ω or higher.
Set this switch to left (
).
IMPEDANCE
SELECTOR
SELECTEUR
D’IMPEDANCE
REAR
CENTER
C
D
DUAL
FRONT LEVEL switch
(Australia model only)
Normally set to “0 dB”. If desired, you can decrease the
output level at the FRONT SPEAKERS terminals by 10 dB by
setting this switch to “–10 dB”.
l0 dB 0 dB
FRONT
LEVEL
l
SINGLE
Center speaker
8
Center speaker
How to Connect:
Connect the SPEAKERS terminals to your speakers with wire
of the proper gauge, cut as short as possible. If the
connections are faulty, no sound will be heard from the
speakers. Make sure that the polarity of the speaker wires is
correct, that is, + and – markings are observed. If these wires
are reversed, the sound will be unnatural and will lack bass.
Do not let the bare speaker wires touch each other and do
not let them touch the metal parts of this unit as this could
damage this unit and/or speakers.
Note
Use speakers with the specified impedance shown on the rear
of this unit.
For connecting to the FRONT SPEAKERS terminals
Red: positive (+)
Black: negative (–)
For connecting to the REAR and CENTER SPEAKERS
terminals
Red: positive (+)
Black: negative (–)
➀ Unscrew the knob.
➁ Insert the bare wire.
2
1
[Remove approx. 5mm
(1/4”) insulation from
the speaker wires.]
➂ Tighten the knob and
secure the wire.
3
<U.S.A., Canada and General models only>
➀ Press up the tab.
➁ Insert the bare wire.
➀
➂
[Remove approx. 5mm
(1/4”) insulation from
the speaker wires.]
➂ Release the tab and
secure the wire.
➁
Banana Plug connections are also possible. Simply insert the
Banana Plug connector into the corresponding terminal.
9
ABOUT THE ACCESSORY TERMINALS
AC OUTLET(S) (SWITCHED)
FRONT OUTPUT terminals
(U.S.A., Canada and General models)
...........................................................2 SWITCHED OUTLETS
(Australia model) ................................. 1 SWITCHED OUTLET
Use these to connect the power cords from your components
to this unit.
The power to the SWITCHED outlets is controlled by this unit’s
POWER switch or the provided remote control transmitter’s
POWER key. These outlets will supply power to any
component whenever this unit is turned on.
The maximum power (total power consumption of
components) that can be connected to the SWITCHED AC
OUTLET(S) is 120 watts.
These terminals are for front channel line output. There is no
connection to these terminals when you use the built-in
amplifier.
However, if you drive front speakers with an external stereo
power amplifier, connect the input terminals of the external
amplifier (MAIN IN or AUX terminals of a power amplifier or an
integrated amplifier) to these terminals.
GND terminal (For turntable use)
Connecting the ground wire of the turntable to this terminal will
normally minimize hum, but in some cases better results may
be obtained with the ground wire disconnected.
This terminal is for output to a monaural amplifier driving a
subwoofer. Only frequencies below 200 Hz from the front and
center channels are output.
ADDING A SUBWOOFER
You may wish to add a subwoofer to reinforce the bass
frequencies.
Connect the LOW PASS terminal to the INPUT terminal of
the subwoofer amplifier, and connect the speaker terminals
of the subwoofer amplifier to the subwoofer.
With some subwoofers, including the Yamaha Active Servo
Processing Subwoofer System, the amplifier and subwoofer
are in the same unit.
OUTPUT
CENTER
REAR
LOW
PASS
fc:200Hz
Subwoofer system
10
These terminals are for rear channel line output. There is no
connection to these terminals when you use the built-in
amplifier.
However, if you drive rear speakers with an external stereo
power amplifier, connect the input terminals of the external
amplifier (MAIN IN or AUX terminals of a power amplifier or an
integrated amplifier) to these terminals.
CENTER OUTPUT terminal
LOW PASS terminal
FRONT
REAR OUTPUT terminals
This terminal is for center channel line output. There is no
connection to this terminal when you use the built-in amplifier.
However, if you drive a center speaker with an external power
amplifier, connect the input terminal of the external amplifier to
this terminal.
ANTENNA CONNECTIONS
●
●
Each antenna should be connected to the designated terminals correctly, referring to the following diagram.
Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide sufficient signal
strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an indoor one. If you experience
poor reception quality, an outdoor antenna may result in improvement.
Outdoor FM antenna
Outdoor AM antenna
Indoor FM
antenna
(included)
AM loop
antenna
(included)
GND
75Ω UNBAL.
FM
ANT
300-ohm
feeder
GND
AM
ANT
TAPE
PB
PHONO
75-ohm
coaxial cable
CD
75-ohm/300-ohm
antenna adapter
Ground
Connecting the AM loop antenna
1
2
➀
➂
➁
3
Orient so that the best
reception is obtained.
* The AM loop antenna should be placed apart from the main unit. The antenna may be hung on a wall.
* The AM loop antenna should be kept connected, even if an outdoor AM antenna is connected to this unit.
GND terminal
For maximum safety and minimum interference, connect the
GND terminal to a good earth ground. A good earth ground is
a metal stake driven into moist earth.
Notes
● When connecting the indoor
FM antenna, insert its
connector into the FM ANT
terminal firmly.
● If you need an outdoor
FM antenna to improve
FM reception quality, either
300-ohm feeder or coaxial cable may be used. In locations
troubled by electrical interference, coaxial cable is
preferable.
11
SPEAKER BALANCE ADJUSTMENT
This procedure lets you adjust the sound output level balance between the front, center, and rear speakers using the built-in test
tone generator. With this adjustment, the sound output level heard at the listening position will be the same from each speaker.
This is important for the best performance of the digital sound field processor.
The adjustment of each speaker output level should be done at your listening position with the remote control transmitter.
Otherwise, the result may not be satisfactory.
<For U.S.A., Canada and Australia models only>
Use the remote control transmitter with the YPC-USER-LEARN switch on it set to the YPC position.
1
5
4
<U.S.A., Canada and
Australia models>
SEARCH
STOP
PLAY
DIR A
DIR B
<General model>
TAPE MON
REC PAUSE
REC MUTE
REC/PAUSE
DIR A
PLAY
TEST
SEARCH
PAUSE/STOP
PLAY
LD/TV
5
PRO LOGIC
1
ENHANCED
DISPLAY
STOP
CONCERT
VIDEO
MONO
MOVIE
3
4
DISCO
ROCK
HALL
6
7
2
VCR 1
VCR 2
SURROUND
STADIUM
5
V–AUX
HALL
DELAY TIME
1
ON/OFF
5
Set to the “ ∞ ” position.
PRO LOGIC ENHANCED
A
B
ON
ON
DISCO
OFF
OFF
* If you use two front speaker systems, press both the A
and B switches.
3
BASS
TREBLE
l
l
2
3
3
4
4
5
5
0
BALANCE
l
2
l
2
3
3
4
4
5
5
Set to the “0” position.
12
V AUX
VOLUME
Select the
PRO LOGIC or
PRO LOGIC
ENHANCED mode, so that the corresponding name is
illuminated on the display.
DIGITAL SOUND FIELD PROCESSOR
SPEAKERS
2
EFFECT
ON/OFF
POWER
Select the front speakers to be used.
0
VCR 2
MASTER
VOLUME
4
l
DISCO
3
2
2
ROCK
REAR
LEVEL
VCR 1
SUR.
MONO MOVIE STADIUM
8
EFFECT
DSP
CENTER
LEVEL
TAPE MON
LD/TV
ENHANCED CNCT VIDEO
PRO LOGIC
CHAPTER/CH
DIR B
STOP
0
l
2
2
3
3
4
4
L 5
5 R
CONCERT
VIDEO
ROCK CONCERT
CONCERT
HALL
MONO
MOVIE
STADIUM
EFFECT
5
<U.S.A., Canada and
Australia models>
8
6
<General model>
SURROUND
STADIUM
DISCO
ROCK
HALL
5
6
7
8
EFFECT
DSP
ON/OFF
CENTER LEVEL
V–AUX
REC PAUSE
7
MASTER
VOLUME
DELAY
TIME
REAR LEVEL
RESET
CLEAR
CENTER
LEVEL
DIR B
TAPE MON
LD/TV
ENHANCED CNCT VIDEO
VCR 1
SUR.
MONO MOVIE STADIUM
ROCK
REAR
LEVEL
PLAY
STOP
PRO LOGIC
8
7
TEST
DIR A
TEST
HALL
DISCO
VCR 2
EFFECT
ON/OFF
V AUX
DELAY TIME
VOLUME
8
6
Select the center channel output mode according to your
speaker configuration.
(Refer to “SPEAKER CONFIGURATION” on page 6.)
CENTER
MODE
7
TEST
TEST
ER
Flashes continuously.
NORMAL
WIDE
PHANTOM
8
Turn up the volume.
MASTER
VOLUME
<U.S.A., Canada
and Australia
models>
<General
model>
VOLUME
On the feature of each mode, refer to the “Note” shown
below.
Note
In step 6, when you select the center channel output mode,
note the following.
For 5 speaker configuration)
NORMAL: Select this mode when you use a center speaker
that is smaller than the front speakers. In this
mode, the bass tone will be output from the front
speakers.
WIDE:
Select this mode when you use the center speaker
approximately same sized as the front speakers.
You will hear a test tone (like pink noise) from the left front
speaker, then the center speaker, then the right front
speaker, and then the rear speakers, for about two
seconds each. The display changes as shown below.
Front (L)
Center
TEST
For 4 speaker configuration)
PHANTOM: Select this mode when you do not use the center
speaker. The center sound will be output from the
left and right front speakers.
Rear
(L and R)
Front (R)
* The test tone from the left rear speaker and the right rear
speaker will be heard at the same time.
CONTINUED
13
<U.S.A.,Canada and
Australia models>
PRO LOGIC
ENHANCED
CONCERT
VIDEO
MONO
MOVIE
1
2
3
4
<General model>
VCR 2
SURROUND
STADIUM
DISCO
ROCK
5
6
7
HALL
DSP
10
1
12
9
9
Adjust the BALANCE control so that the effect sound
output level of the left front speaker and the right front
speaker are the same.
CENTER LEVEL
0
2
RESET
11
3
10
DIR A
PLAY
TEST
STOP
CENTER
LEVEL
MONO MOVIE STADIUM
PRO LOGIC
DIR B
TAPE MON
LD/TV
ENHANCED CNCT VIDEO
VCR 1
SUR.
ROCK
REAR
LEVEL
HALL
DELAY TIME
DISCO
VCR 2
EFFECT
ON/OFF
V AUX
VOLUME
CLEAR
Adjust the sound output level of the rear speakers to
be at the same level as that of the front speakers with
the REAR LEVEL keys.
4
L 5
12
10
11
<U.S.A., Canada
and Australia
models>
2
4
TEST
DELAY
TIME
l
3
MASTER
VOLUME
REAR LEVEL
BALANCE
l
ON/OFF
REC PAUSE
V–AUX
8
EFFECT
<General model>
REAR LEVEL
5 R
REAR
LEVEL
Adjust the sound output level of the center speaker to
be at the same level as that of the front speakers with
the CENTER LEVEL keys.
TEST
<U.S.A., Canada
and Australia
models>
<General
model>
Lights up.
0
REAR
Adjustable
CENTER LEVEL
CENTER
LEVEL
12
Cancel the test tone.
TEST
TEST
R
TEST
Stops flashing and disappears
Lights up.
CENTER
00
Notes
Once you have completed these adjustments, you can
adjust whole sound level on your audio system by using
the VOLUME control (or the VOLUME keys on the remote
control transmitter).
● If you use external power amplifiers, their volume controls
may also be adjusted to achieve proper balance.
● In step 10, if the center channel mode is in the
“PHANTOM” position, the sound output level of the center
speaker cannot be adjusted. This is because in this mode,
the center sound is automatically output from the left and
right front speakers.
● <Australia model only>
If there is insufficient sound output from the center and
rear speakers, you may decrease the front speaker output
level by setting the FRONT LEVEL switch on the rear
panel to “–10 dB”.
●
Adjustable
14
BASIC OPERATIONS
1, 6
3
2
4
7
7
TO PLAY A SOURCE
1
5
Play the source. (For detailed information on the
tuning operation, refer to page 18.)
6
Set to the “ ∞ ” position.
2
POWER
Adjust to the desired output level.
7
3
Select the desired input source by using the input
selector buttons.
(For video sources, turn the TV/monitor ON.)
TAPE
MONITOR
TUNER
CD
PHONO
VIDEO AUX
VCR 2
VCR 1
LD/TV
* The name of the selected input source will appear in
the display.
4
Select the front speakers to be used.
SPEAKERS
A
B
ON
ON
OFF
OFF
If desired, adjust the BASS, TREBLE, BALANCE
controls, etc. (refer to page 17) and use the digital
sound field processor. (Refer to page 24.)
Notes on using the input selector buttons
Note that pressing on each input selector button selects
the source which is connected to the corresponding input
terminals on the rear panel.
* To select the source connected to the VIDEO AUX
terminals on the front panel, press VIDEO AUX.
● The selection of TAPE MONITOR cannot be canceled by
pressing another input selector button. To cancel it, press
TAPE MONITOR again.
When you select a button other than TAPE MONITOR,
make sure that TAPE MONITOR is not also selected.
● If you select the input selector button for a video source
without canceling the selection of TAPE MONITOR, the
playback result will be the video image from the video
source and the sound from the audio tape.
● Once you play a video source, its video image will not be
interrupted even if the input selector button for an audio
source is selected.
●
To turn off the power
Press the POWER switch again.
* If you use two front speaker systems, press both the A and
B switches.
15
1, 4
2
TO RECORD A SOURCE TO TAPE
(OR DUB FROM TAPE TO TAPE)
1
2
3
4
16
Note
DSP, VOLUME, BASS, TREBLE and BALANCE control
settings have no effect on the material being recorded.
Select the source to be recorded.
TAPE
MONITOR
TUNER
CD
PHONO
VIDEO AUX
VCR 2
VCR 1
LD/TV
Play the source and then turn the VOLUME control
up to confirm the input source. (For detailed information
on the tuning operations, refer to page 18.)
Set the tape deck or VCR to the recording mode.
If the tape deck is used for recording, you can monitor
the sounds being recorded by pressing TAPE
MONITOR.
TAPE
MONITOR
TUNER
CD
PHONO
VIDEO AUX
VCR 2
VCR 1
LD/TV
Selecting the SPEAKER system
Because one or two speaker systems (as front speakers) can
be connected to this unit, the SPEAKERS switches allow you
to select speaker system A or B, or both at once.
Adjusting the BASS and TREBLE
controls
BASS
l
0
TREBLE
l
2
SPEAKERS
A
B
ON
ON
OFF
OFF
3
l
2
3
4
5
0
2
3
4
BASS
l
2
3
4
5
4
5
5
: Turn this clockwise to increase (or counterclockwise to decrease) the low frequency
response.
Adjusting the BALANCE control
Adjust the balance of the output volume to the left and right
speakers to compensate for sound imbalance caused by
speaker location or listening room conditions.
BALANCE
l
0
l
2
2
3
TREBLE : Turn this clockwise to increase (or counterclockwise to decrease) the high frequency
response.
Note
These controls are effective only for the sound from the front
speakers.
3
4
4
L 5
5 R
Note
This control is effective only for the sound from the front
speakers.
When you listen with headphones
Connect the headphones to the PHONES jack. You can listen
to the sound to be output from the front speakers through
headphones.
When listening with headphones privately, set both the
SPEAKERS A and B switches to the OFF position and switch
off the digital sound field processor (so that no DSP program
name is illuminated on the display) by pressing the EFFECT
switch.
PHONES
17
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement