Sony HTD-DW760 System
masterpage:Right
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB01COV_HT-DDW760-U.fm]
GB01COV_HT-DDW760-U.book Page 1 Tuesday, April 20, 2004 3:10 PM
4-252-086-13(1)
Home Theatre
System
Operating Instructions
HT-DDW760
©2004 Sony Corporation
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB02REG_HT-DDW760-U.fm]
masterpage:Left
GB01COV_HT-DDW760-U.book Page 2 Tuesday, April 20, 2004 3:10 PM
WARNING
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
To prevent fire, do not cover the ventilation of the
apparatus with newspapers, table-cloths, curtains, etc.
And don’t place lighted candles on the apparatus.
To prevent fire or shock hazard, do not place objects
filled with liquids, such as vases, on the apparatus.
Do not install the appliance in a confined space,
such as a bookcase or built-in cabinet.
Don’t throw away batteries with
general house waste; dispose of
them correctly as chemical waste.
For customers in Canada
CAUTION
TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
Except for customers in Europe
ENERGY STAR® is a U.S. registered
mark. As an ENERGY STAR® partner,
Sony Corporation has determined that
this product meets the ENERGY
STAR® guidelines for energy
efficiency.
2GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB02REG_HT-DDW760-U.fm]
masterpage:Right
GB01COV_HT-DDW760-U.book Page 3 Tuesday, April 20, 2004 3:10 PM
About area codes
About This Manual
• The instructions in this manual are for model
HT-DDW760. Check your model number by looking
at the lower right corner of the front panel. In this
manual, HT-DDW760 models of area code CEL is
used for illustration purposes unless stated otherwise.
• The instructions in this manual describe the controls
on the receiver. You can also use the controls on the
supplied remote if they have the same or similar
names as those on the receiver. For details on the use
of your remote, see pages 37–43.
The HT-DDW760 consists of:
• Receiver
– Models of area code CEL, CEK
only
– Models of other area code
• Speaker system
– Front speaker (left)
– Front speaker (right)
– Center speaker
– Surround speaker (left)
– Surround speaker (right)
– Sub woofer
STR-DE497P
STR-K760P
SS-MSP760L
SS-MSP760R
SS-CNP760
SS-MSP760SL
SS-MSP760SR
SA-WMSP76
The area code of the receiver you purchased is
shown on the lower portion of the rear panel (see
the illustration below).
R
L
+
+
R
CENTER
L
FRONT
4-XXX-XXX-XX AA
Area code
Any differences in operation, according to the area
code, are clearly indicated in the text, for example,
“Models of area code AA only”.
This receiver incorporates Dolby* Digital and Pro
Logic Surround and the DTS** Digital Surround
System.
* Manufactured under license from Dolby
Laboratories.
“Dolby”, “Pro Logic” and the double-D symbol are
trademarks of Dolby Laboratories.
** “DTS” and “DTS Digital Surround” are registered
trademarks of Digital Theater Systems, Inc.
3GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB01COV_HT-DDW760-UTOC.fm]
masterpage:Left
GB01COV_HT-DDW760-U.book Page 4 Tuesday, April 20, 2004 3:10 PM
Table of Contents
Getting Started
1: Check how to hookup your
components....................................... 5
1a: Connecting components with
digital audio output jacks ........... 7
1b: Connecting components with
multi channel output jacks.......... 9
(Models of area code CEL, CEK
only)
1c: Connecting components with
only analog audio jacks ............ 11
2: Connecting the antennas ................... 13
3: Connecting speakers ......................... 14
4: Connecting the AC power cord ........ 16
5: Setting up the speakers ..................... 17
6: Setting up the sub woofer ................. 19
7: Adjusting the speaker levels and
balance ............................................ 19
— TEST TONE
Amplifier Operation
Selecting the component ....................... 20
Listening to multi channel sound .......... 20
— MULTI CH IN
(Models of area code CEL, CEK
only)
Listening to FM/AM radio.................... 21
Storing FM stations automatically ........ 22
— AUTOBETICAL
(Models of area code CEL, CEK
only)
Presetting radio stations ........................ 22
Using the Radio Data System (RDS).... 23
(Models of area code CEL, CEK
only)
Changing the display............................. 25
About the indications in the display...... 26
Enjoying Surround Sound
Using only the front speakers and sub
woofer............................................. 27
— 2CH STEREO
Enjoying higher fidelity sound ............. 27
— AUTO FORMAT DIRECT
Selecting a sound field.......................... 28
Advanced Adjustments and
Settings
Switching the audio input mode for
digital components ......................... 30
— INPUT MODE
Customizing sound fields ..................... 30
Adjusting the tone................................. 32
Advanced settings................................. 32
Other Operations
Naming preset stations and inputs ........ 34
Using the Sleep Timer .......................... 35
Recording ............................................. 35
Operations Using the Remote
RM-PP760
Before you use your remote.................. 37
Remote button description.................... 37
Selecting the command mode of the
remote............................................. 40
Programming the remote ...................... 41
Additional Information
Precautions ........................................... 44
Troubleshooting.................................... 45
Specifications ....................................... 47
List of button locations and reference
pages............................................... 50
Index ........................................ back cover
4GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB03CON_HT-DDW760-U.fm]
masterpage:Right
GB01COV_HT-DDW760-U.book Page 5 Tuesday, April 20, 2004 3:10 PM
Getting Started
Steps 1a through 1c beginning on page 7 describe how to hook up your components to this receiver.
Before you begin, refer to “Connectable components” below for the pages which describe how to
connect each component.
After hooking up all your components, proceed to “2: Connecting the antennas” (page 13).
Getting Started
1: Check how to hookup your components
Connectable components
Component to be connected
Page
DVD player
With digital audio outputa)
7–8
With multi channel audio outputb)
9–10
With analog audio output onlyc)
7–8
TV monitor
With composite video input only
8, 10 or 12
Satellite tuner
With digital audio outputa)
7–8
With analog audio output onlyc)
7–8
CD player
With analog audio output onlyc)
11
MD/Tape deck
With analog audio output onlyc)
11
Multi channel decoder (Models of area code CEL, CEK only)
9
VCR
12
a)
Model with a DIGITAL OPTICAL OUTPUT or DIGITAL COAXIAL OUTPUT jack, etc.
(Models of area code CEL, CEK only) Model with a MULTI CH OUTPUT jacks, etc. This connection is used to
output the audio decoded by the component’s internal multi channel decoder through this receiver.
c) Model equipped only with AUDIO OUT L/R jacks, etc.
b)
continued
5GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB03CON_HT-DDW760-U.fm]
masterpage:Left
GB01COV_HT-DDW760-U.book Page 6 Tuesday, April 20, 2004 3:10 PM
Required cords
The hookup diagrams on the subsequent pages assume the use of the following optional connection
cords (A to F) (not supplied unless indicated).
A Audio cord
White (L)
Red (R)
B Audio/video cord
Yellow (video)
White (L/audio)
Red (R/audio)
D Optical digital cord
E Coaxial digital cord (supplied)
Orange
F Monaural audio cord
(Models of area code CEL, CEK only)
C Video cord
Black
Yellow
Tip
Audio cord A can be torn into two monaural audio
cords F.
Notes
• Turn off the power to all components before making any connections.
• Be sure to make connections firmly to avoid hum and noise.
• When connecting an audio/video cord, be sure to match the color-coded pins to the appropriate jacks on the
components: yellow (video) to yellow; white (left, audio) to white; and red (right, audio) to red.
• When connecting optical digital cords, insert the cord plugs straight in until they click into place.
• Do not bend or tie optical digital cords.
6GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB03CON_HT-DDW760-U.fm]
masterpage:Right
GB01COV_HT-DDW760-U.book Page 7 Tuesday, April 20, 2004 3:10 PM
.
1a: Connecting components with digital audio output jacks
Getting Started
Hooking up a DVD player or satellite tuner
For details on the required cords (A–F), see page 6.
1 Connect the audio jacks.
DVD player
OUTPUT
AUDIO
OUT
OUTPUT
L
DIGITAL
COAXIAL
R
E
A
ANTENNA
DIGITAL
OPTICAL
VIDEO 2
IN
MONITOR
AM
VIDEO IN
VIDEO IN
VIDEO OUT
VIDEO IN
VIDEO OUT
DVD IN
COAXIAL
L
L
L
L
L
AUDIO
OUT
CENTER
R
FRONT
SUB
SURROUND WOOFER
MULTI CH IN
IN
CD
R
OUT R IN
MD/TAPE
R AUDIO IN AUDIO OUT R AUDIO IN
DVD VIDEO 2
VIDEO 1
AUDIO IN
D
SUB
WOOFER
A
OUTPUT
OUTPUT
DIGITAL
OPTICAL
AUDIO
OUT
L
R
Satellite tuner
Note
You can listen to the sound of your TV by connecting your TV’s audio output jacks to the VIDEO 2 AUDIO IN jacks
on the receiver. In this case, do not connect the TV’s video output jack to the VIDEO 2 VIDEO IN jack on the
receiver.
continued
7GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB03CON_HT-DDW760-U.fm]
masterpage:Left
GB01COV_HT-DDW760-U.book Page 8 Tuesday, April 20, 2004 3:10 PM
2 Connect the video jacks.
TV monitor
Satellite tuner
OUTPUT
INPUT
VIDEO
VIDEO
C
C
ANTENNA
DIGITAL
OPTICAL
VIDEO 2
IN
MONITOR
AM
VIDEO IN
VIDEO IN
VIDEO OUT
VIDEO IN
VIDEO OUT
DVD IN
COAXIAL
L
L
L
L
L
AUDIO
OUT
CENTER
R
FRONT
SUB
SURROUND WOOFER
MULTI CH IN
IN
CD
R
OUT R IN
MD/TAPE
R AUDIO IN AUDIO OUT R AUDIO IN
DVD VIDEO 2
VIDEO 1
AUDIO IN
SUB
WOOFER
C
OUTPUT OUTPUT
VIDEO
DVD player
8GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB03CON_HT-DDW760-U.fm]
masterpage:Right
GB01COV_HT-DDW760-U.book Page 9 Tuesday, April 20, 2004 3:10 PM
(Models of area code CEL, CEK only)
1 Connect the audio jacks.
If your DVD player is equipped with multi channel output jacks, you can connect it to this receiver’s
MULTI CH IN jacks to enjoy the multi channel sound. Alternatively, the multi channel input jacks can
be used to connect an external multi channel decoder.
For details on the required cords (A–F), see page 6.
Getting Started
1b: Connecting components with multi channel output
jacks
ANTENNA
DIGITAL
OPTICAL
VIDEO 2
IN
MONITOR
AM
VIDEO IN
VIDEO IN
VIDEO OUT
VIDEO IN
VIDEO OUT
DVD IN
COAXIAL
L
L
L
L
L
AUDIO
OUT
CENTER
R
FRONT
SUB
SURROUND WOOFER
MULTI CH IN
A A
FRONT
IN
CD
R
OUT R IN
MD/TAPE
R AUDIO IN AUDIO OUT R AUDIO IN
DVD VIDEO 2
VIDEO 1
AUDIO IN
SUB
WOOFER
F F
SURROUND CENTER
L
R
MULTI CH OUT
SUB
WOOFER
DVD player,
Multi channel decoder, etc.
Tip
This connection also allows you to enjoy software with multi channel audio recorded in formats other than the Dolby
Digital and DTS.
Note
When you make connections to the MULTI CH IN jacks, you will need to adjust the level of the surround speakers
and sub woofer using the controls on the connected component.
continued
9GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB03CON_HT-DDW760-U.fm]
masterpage:Left
GB01COV_HT-DDW760-U.book Page 10 Tuesday, April 20, 2004 3:10 PM
2 Connect the video jacks.
DVD player
TV monitor
OUTPUT
INPUT
VIDEO
VIDEO
C
C
ANTENNA
DIGITAL
OPTICAL
VIDEO 2
IN
MONITOR
AM
VIDEO IN
VIDEO IN
VIDEO OUT
VIDEO IN
VIDEO OUT
DVD IN
COAXIAL
L
L
L
L
L
AUDIO
OUT
CENTER
R
FRONT
SUB
SURROUND WOOFER
MULTI CH IN
IN
CD
R
OUT R IN
MD/TAPE
R AUDIO IN AUDIO OUT R AUDIO IN
DVD VIDEO 2
VIDEO 1
AUDIO IN
SUB
WOOFER
10GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB03CON_HT-DDW760-U.fm]
masterpage:Right
GB01COV_HT-DDW760-U.book Page 11 Tuesday, April 20, 2004 3:10 PM
1c: Connecting components with only analog audio jacks
Getting Started
Hooking up audio components
For details on the required cords (A–F), see page 6.
ANTENNA
DIGITAL
OPTICAL
VIDEO 2
IN
MONITOR
AM
VIDEO IN
VIDEO IN
VIDEO OUT
VIDEO IN
VIDEO OUT
DVD IN
COAXIAL
L
L
L
L
L
AUDIO
OUT
CENTER
R
SUB
SURROUND WOOFER
IN
R
OUT R IN
MD/TAPE
CD
MULTI CH IN
l
A
A
OUT
A
SUB
WOOFER
IN
INPUT OUTPUT
OUTPUT
LINE
LINE
CD player
R AUDIO IN AUDIO OUT R AUDIO IN
DVD VIDEO 2
VIDEO 1
AUDIO IN
l
FRONT
LINE
L
L
R
R
MD/Tape deck
continued
11GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB03CON_HT-DDW760-U.fm]
masterpage:Left
GB01COV_HT-DDW760-U.book Page 12 Tuesday, April 20, 2004 3:10 PM
Hooking up video components
If you connect your TV to the MONITOR VIDEO OUT jack, you can watch the video from the selected
input (page 20). For details on the required cords (A–F), see page 6.
VCR
OUTPUT
VIDEO
OUT
TV monitor
AUDIO
OUT
INPUT
L
VIDEO
R
B
C
ANTENNA
DIGITAL
OPTICAL
VIDEO 2
IN
MONITOR
AM
VIDEO IN
VIDEO IN
VIDEO OUT
VIDEO IN
VIDEO OUT
DVD IN
COAXIAL
L
L
L
L
L
AUDIO
OUT
CENTER
SUB
SURROUND WOOFER
MULTI CH IN
IN
CD
R
OUT R IN
MD/TAPE
R AUDIO IN AUDIO OUT R AUDIO IN
DVD VIDEO 2
VIDEO 1
AUDIO IN
SUB
WOOFER
L
OUT
L
R
FRONT
B
IN
B
INPUT OUTPUT
VIDEO
IN
VIDEO
OUT
AUDIO
IN
AUDIO
OUT
L
L
R
R
VCR
12GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB03CON_HT-DDW760-U.fm]
masterpage:Right
GB01COV_HT-DDW760-U.book Page 13 Tuesday, April 20, 2004 3:10 PM
2: Connecting the antennas
AM loop antenna
(supplied)
FM wire antenna
(supplied)
Getting Started
Connect the supplied AM loop antenna and FM wire antenna.
ANTENNA
DIGITAL
OPTICAL
VIDEO 2
IN
MONITOR
AM
VIDEO IN
VIDEO IN
VIDEO OUT
VIDEO IN
VIDEO OUT
DVD IN
COAXIAL
L
L
L
L
L
AUDIO
OUT
CENTER
R
FRONT
SUB
SURROUND WOOFER
MULTI CH IN
IN
CD
R
OUT R IN
MD/TAPE
R AUDIO IN AUDIO OUT R AUDIO IN
DVD VIDEO 2
VIDEO 1
AUDIO IN
SUB
WOOFER
*
*
The shape of the connector varies depending on the area code.
Notes
• To prevent noise pickup, keep the AM loop antenna away from the receiver and other components.
• Be sure to fully extend the FM wire antenna.
• After connecting the FM wire antenna, keep it as horizontal as possible.
13GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB03CON_HT-DDW760-U.fm]
masterpage:Left
GB01COV_HT-DDW760-U.book Page 14 Tuesday, April 20, 2004 3:10 PM
3: Connecting speakers
Connect your speakers to the receiver. This receiver allows you to use a 5.1 channel speaker system.
To fully enjoy theater-like multi channel surround sound requires five speakers (two front speakers, a
center speaker, and two surround speakers) and a sub woofer (5.1 channel).
Example of 5.1 channel speaker system configuration
Center speaker
Front speaker (Right)
Surround speaker (Right)
Front speaker (Left)
Sub woofer
Surround speaker (Left)
Tips
• Since the sub woofer does not emit highly directional signals, you can place it wherever you want.
• For greater flexibility in the positioning of the speakers, use the optional WS-FV11 or WS-FV10D floor stand
(available only in certain countries).
Note
Connect the long speaker connecting cords to the surround speaker terminals and the short speaker connecting cords
to the front and center speaker terminals.
Attaching foot pads
To prevent speaker vibration or movement, attach the supplied foot pads to the speaker as shown in the
illustration below.
Note
Be sure to attach the supplied foot pads to the sub woofer as well.
14GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB03CON_HT-DDW760-U.fm]
masterpage:Right
GB01COV_HT-DDW760-U.book Page 15 Tuesday, April 20, 2004 3:10 PM
Required cords
B Monaural audio cord (supplied)
(+)
(–)
Black
Surround speaker
(Right)
E
Surround speaker
(Left)
e
E
A
Getting Started
A Speaker cords (supplied)
Center speaker
e
E
e
A
A
MONITOR
VIDEO OUT
R
L
+
R
+
L
+
+
AUDIO
OUT
SUB
WOOFER
R
L
SURROUND
R
L
FRONT
CENTER
SPEAKERS
A
B
A
INPUT
E
Sub woofer
e
Front speaker
(Right)
E
e
Front speaker
(Left)
15GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB03CON_HT-DDW760-U.fm]
masterpage:Left
GB01COV_HT-DDW760-U.book Page 16 Tuesday, April 20, 2004 3:10 PM
4: Connecting the AC
power cord
Setting the voltage selector
for the receiver and sub
woofer
Connecting the AC power
cord
Connect the AC power cord to a wall outlet.
AC power cord
If your receiver and sub woofer has a voltage
selector on the rear panel, check that the voltage
selector is set to the local power supply voltage.
If not, use a screwdriver to set the selector to the
correct position before connecting the AC power
cord to a wall outlet.
Receiver
VOLTAGE SELECTOR
120V
220V
240V
To a wall outlet
Sub woofer
VOLTAGE SELECTOR
120V
220 / 230V
16GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB03CON_HT-DDW760-U.fm]
masterpage:Right
GB01COV_HT-DDW760-U.book Page 17 Tuesday, April 20, 2004 3:10 PM
Performing initial setup
operations
1
2
3
Press ?/1 to turn off the receiver.
You can use the SET UP menu to set the
distance and location of the speakers connected
to this receiver.
1
2
3
Press ?/1 to turn on the receiver.
Press MAIN MENU repeatedly to select
“ SET UP ”.
Hold down ?/1 for 5 seconds.
Press
or
repeatedly to select the
parameter you want to adjust.
“PUSH” and “ENTER” appears in the
display alternatingly.
For details, see “Speaker setup parameters”
below.
Press ENTER.
Note
“CLEARING” appears in the display for a
while, then “CLEARED” appears.
The following are reset to their factory
settings.
• All settings in the SET UP, LEVEL,
TONE and CUSTOMIZE menus.
• The sound field memorized for each
input and preset station.
• All sound field parameters.
• All preset stations.
• All index names for inputs and preset
stations.
• MASTER VOLUME –/+ is set to “VOL
MIN”.
Some speaker setup items may appear dimmed in
the display. This means that they have been
adjusted automatically due to other speaker
settings or may not be adjustable.
4
Getting Started
Before using the receiver for the first time,
initialize the receiver by performing the
following procedure.
This procedure can also be used to return
settings you have made to their factory defaults.
Use the buttons on the receiver for the operation.
5: Setting up the speakers
Press + or – repeatedly to select the
setting you want.
The setting is entered automatically.
5
Repeat steps 3 and 4 until you have set
all of the items that follow.
Speaker setup parameters
The initial setting is underlined.
x
L
R
DIST. X.X m (XX ft.)
(Front speaker distance)
Initial setting: 3.0 m (10 ft.)
Lets you set the distance from your listening position
to the front speakers (A). You can adjust from 1.0
meter to 7.0 meters (3 to 23 feet) in 0.1 meter (1 foot)
steps.
If both front speakers are not placed an equal distance
from your listening position, set the distance to the
closest speaker.
B
A
30˚
100˚-120˚
C
30˚
A
100˚-120˚
C
continued
17GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB03CON_HT-DDW760-U.fm]
masterpage:Left
GB01COV_HT-DDW760-U.book Page 18 Tuesday, April 20, 2004 3:10 PM
x
C
DIST. X.X m (XX ft.)
(Center speaker distance)
Initial setting: 3.0 m (10 ft.)
Lets you set the distance from your listening position
to the center speaker. Center speaker distance should
be set from a distance equal to the front speaker
distance (A on page 17) to a distance 1.5 meters (5
feet) closer to your listening position (B on page 17).
x
SR
SL
DIST. X.X m (XX ft.)
(Surround speaker distance)
Initial setting: 3.0 m (10 ft.)
Lets you set the distance from your listening position
to the surround speakers. Surround speaker distance
should be set from a distance equal to the front speaker
distance (A on page 17) to a distance 4.5 meters (15
feet) closer to your listening position (C on page 17).
If both surround speakers are not placed an equal
distance from your listening position, set the distance
to the closest speaker.
Tip
x
SR
SL
PL. XXXX
(Surround speaker placement)
Lets you specify the height of your surround speakers
for proper implementation of the surround effects of
the Cinema Studio EX modes (page 28).
B
B
60
A
A
30
• LOW
Select if the height of your surround speakers
corresponds to section A.
• HIGH
Select if the height of your surround speakers
corresponds to section B.
The receiver lets you to input the speaker position in
terms of distance. However, it is not possible to set the
center speaker further than the front speakers. Also, the
center speaker cannot be set more than 1.5 meters (5
feet) closer than the front speakers.
Likewise, the surround speakers cannot be set further
away from the listening position than the front
speakers. And they can be no more than 4.5 meters (15
feet) closer.
This is because incorrect speaker placement is not
conducive to the enjoyment of surround sound.
Please note that, setting the speaker distance closer than
the actual location of the speakers will cause a delay in
the output of the sound from that speaker. In other
words, the speaker will sound like it is further away.
For example, setting the center speaker distance 1–2
meters (3–6 feet) closer than the actual speaker
position will create a fairly realistic sensation of being
“inside” the screen. If you cannot obtain a satisfactory
surround effect because the surround speakers are too
close, setting the surround speaker distance closer
(shorter) than the actual distance will create a larger
sound stage.
Adjusting these parameter while listening to the sound
often results in much better surround sound. Give it a
try!
18GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB03CON_HT-DDW760-U.fm]
masterpage:Right
GB01COV_HT-DDW760-U.book Page 19 Tuesday, April 20, 2004 3:10 PM
7: Adjusting the speaker
levels and balance
— TEST TONE
Listening to the sub woofer
Adjust the speaker levels and balance while
listening to the test tone from your listening
position. Use the remote for the operation.
POWER indicator
POWER
Getting Started
6: Setting up the sub
woofer
Tip
The receiver employs a test tone with a frequency
centered at 800 Hz.
Before playing the program source, set the
volume to minimum on the receiver.
1
2
3
Press input buttons (e.g., DVD) to
select the program source (e.g., DVD
player).
Press POWER on the sub woofer.
Press ?/1 to turn on the receiver.
Press TEST TONE.
“T. TONE” appears in the display and the
test tone is output from each speaker in
sequence.
Front (left) t Center t Front (right) t
Surround (right) t Surround (left) t
Sub woofer
Turn on the receiver.
The POWER indicator on the sub woofer
lights up.
4
1
2
3
Play the program source.
Adjust the speaker levels and balance
using the LEVEL menu so that the level
of the test tone sounds the same from
each speaker.
For details on the LEVEL menu settings,
see page 30.
Adjusting the level
Tips
Slight adjustments to the system can enhance
your sound enjoyment.
LEVEL
• To adjust the level of all speakers at the same
time, press MASTER VOL +/– on the remote or
turn MASTER VOLUME –/+ on the receiver.
• The adjusted value are shown in the display
during adjustment.
4
Press TEST TONE again after
adjustment.
The test tone turns off.
Turn LEVEL to adjust the volume.
Notes
Set the volume level to best suit your preference
according to the program source.
• (Models of area code CEL, CEK only) The test tone
cannot be used when MULTI CH IN function is used.
• Although these adjustments can also be made via the
front panel using the LEVEL menu (when the test
tone is output, the receiver switches to the LEVEL
menu automatically), we recommend you follow the
procedure described above and adjust the speaker
levels from your listening position using the remote.
• The bass redirection circuitry is always active, so you
may hear some sound output from the sub woofer
when test tone is output from other speakers.
However, this is not a malfunction.
Note
Do not set the volume of the sub woofer to maximum.
Extraneous noise may be heard.
19GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB04BSC_HT-DDW760-U.fm]
masterpage:Left
GB01COV_HT-DDW760-U.book Page 20 Tuesday, April 20, 2004 3:10 PM
Amplifier Operation
Selecting the component
1
Press input buttons to select the input.
To select the
Press
VCR
VIDEO 1
or VIDEO 2
Satellite tuner
VIDEO 2
DVD player
DVD
MD or tape deck
MD/TAPE
CD player
CD
Built-in tuner (FM/AM) TUNER FM/AM
The selected input appears in the display.
2
Turn on the component and start
playback.
Note
If you select the VCR or DVD player, set the
TV’s video input to match the component you
selected.
3
Turn MASTER VOLUME –/+ to adjust
the volume.
Note
To avoid damaging your speakers, make sure that
you turn down the volume before you turn off the
receiver.
To mute the sound
Press MUTING on the remote.
The muting function will be canceled when you
do the following.
• Press MUTING on the remote again.
• Turn the power off.
• Increase the volume.
Listening to multi channel
sound
— MULTI CH IN
(Models of area code CEL, CEK only)
You can select the audio directly from the
components connected to the MULTI CH IN
jacks. This enables you to enjoy high quality
analog inputs such as DVD. When MULTI CH
IN is selected, the tone and sound field cannot be
used.
Press MULTI CH IN.
Press again to cancel the MULTI CH IN
function.
Note
To optimize the sound balance of this system, we
recommend that you set the speaker configuration of
your DVD player as follows:
Speaker type
Settings
FRONT
SMALL
CENTER
SMALL
SURROUND/REAR
SMALL
SUB WOOFER
YES
When MULTI CHANNEL
DECODING indicator lights up
(Models of area code CEL, CEK only)
The MULTI CHANNEL DECODING indicator
lights up when the receiver is decoding multi
channel sources.
However, this indicator does not light up if you
select 2CH STEREO mode.
To use the headphones
Connect the headphones to the PHONES jack.
When the headphones are connected, speaker
output is automatically canceled and “SP” does
not light up in the display.
20GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB04BSC_HT-DDW760-U.fm]
masterpage:Right
GB01COV_HT-DDW760-U.book Page 21 Tuesday, April 20, 2004 3:10 PM
Listening to FM/AM radio
You can enter the frequency of the station you
want directly. Use the remote for the operation.
1
The last received station is tuned in.
Tip
Tip
The tuning scale differs depending on the area code as
shown in the following table. For details on area codes,
see page 3.
Area code
FM
AM
CA
100 kHz
10 kHz*
CEL, CEK, SP, AU
50 kHz
9 kHz
E51
50 kHz
10 kHz
* The AM tuning scale can be changed (see page 48).
Automatic tuning
If you do not know the frequency of the station
you want, you can let the receiver scan all
available stations in your area.
1
Press TUNER FM/AM repeatedly to
select the FM or AM band.
The last received station is tuned in.
2
Press TUNER repeatedly to select the
FM or AM band.
Press TUNING + or TUNING –.
Press TUNING + to scan from low to high;
press TUNING – to scan from high to low.
The receiver stops scanning whenever a
station is received.
You can also use TUNER FM/AM on the
receiver.
2
3
Press D.TUNING.
Press the numeric buttons to enter the
frequency.
Amplifier Operation
You can listen to FM and AM broadcasts
through the built-in tuner. Before operation,
make sure you have connected the FM and AM
antennas to the receiver (see page 13).
Direct tuning
Example 1: FM 102.50 MHz
Press 1 b 0 b 2 b 5 b 0
Example 2: AM 1,350 kHz
(You do not have to enter the last “0” when
the tuning scale is set to 10 kHz.)
Press 1 b 3 b 5 b 0
If you have tuned in an AM station, adjust
the direction of the AM loop antenna for
optimum reception.
If you cannot tune in a station
and the entered numbers flash
Make sure you have entered the right frequency.
If not, repeat steps 2 and 3. If the entered
numbers still flash, the frequency is not used in
your area.
Tip
If “STEREO” flashes in the display and the FM stereo
reception is poor, press FM MODE to change to
monaural (MONO). You will not be able to enjoy the
stereo effect, but the sound will be less distorted. To
return to stereo mode, press FM MODE again.
21GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB04BSC_HT-DDW760-U.fm]
masterpage:Left
GB01COV_HT-DDW760-U.book Page 22 Tuesday, April 20, 2004 3:10 PM
Storing FM stations
automatically
— AUTOBETICAL
Presetting radio stations
You can preset up to 30 FM or AM stations.
Then you can easily tune in the stations you
often listen to.
(Models of area code CEL, CEK only)
This function lets you store up to 30 FM and FM
RDS stations in alphabetical order without
redundancy. Additionally, it only stores the
stations with the clearest signals.
If you want to store FM or AM stations one by
one, see “Presetting radio stations”.
Use the buttons on the receiver for the operation.
1
2
Presetting radio stations
1
The last received station is tuned in.
2
Press ?/1 to turn off the receiver.
Hold down MEMORY and press ?/1 to
turn the receiver back on.
“AUTO-BETICAL SELECT” appears in
the display and the receiver scans and stores
all the FM and FM RDS stations in the
broadcast area.
For RDS stations, the tuner first checks for
stations broadcasting the same program,
then stores only the one with the clearest
signal. The selected RDS stations are sorted
alphabetically by their Program Service
name, then assigned a 2-character preset
code. For more details on RDS, see
page 23.
Regular FM stations are assigned 2character preset codes and stored after the
RDS station.
When done, “FINISH” appears in the
display momentarily and the receiver
returns to the normal operation.
3
Tune in the station that you want to
preset using Automatic Tuning
(page 21) or Direct Tuning (page 21).
Press MEMORY.
“MEMORY” appears in the display for a
few seconds. Do steps 4 to 5 before the
display goes out.
4
Press PRESET TUNING + or PRESET
TUNING – repeatedly to select a preset
station number.
Each time you press the button, you can
select the preset station number as follows:
tA1yA2y...yA0yB1yB2y...yB0T
tC0y...yC2yC1T
If “MEMORY” goes out before you select
the preset station number, start again from
step 3.
Tip
You can also use the remote to select a preset
station number. Press SHIFT repeatedly to select
a memory page (A, B or C) and then press the
numeric buttons to select a preset number.
Notes
• Do not press any button on the receiver or supplied
remote during autobetical operation, except ?/1.
• If you move to another area, repeat this procedure to
store stations in your new area.
• For details on tuning the stored stations, see “Tuning
to preset stations”.
• If you move the antenna after storing stations with
this procedure, the stored settings may no longer be
valid. If this happens, repeat this procedure to store
the stations again.
Press TUNER FM/AM repeatedly to
select the FM or AM band.
5
Press MEMORY again.
The station is stored to the selected preset
number.
If “MEMORY” goes out before you press
MEMORY, start again from step 3.
6
Repeat steps 2 to 5 to preset another
station.
22GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB04BSC_HT-DDW760-U.fm]
masterpage:Right
GB01COV_HT-DDW760-U.book Page 23 Tuesday, April 20, 2004 3:10 PM
Tuning to preset stations
1
The last received station is tuned in.
Press PRESET TUNING + or PRESET
TUNING – repeatedly to select the
preset station you want.
Each time you press the button, you can
select the preset station as follows:
tA1yA2y...yA0yB1yB2y...yB0T
tC0y...yC2yC1T
Using the remote
1
Press TUNER repeatedly to select the FM or
AM band.
2
Press PRESET/CH/D.SKIP +/– repeatedly
to select the preset station you want.
To select the preset station
directly
Press the numeric buttons on the remote.
The preset station of the selected number in the
current memory page is tuned in. Press SHIFT
repeatedly on the remote to change the memory
page.
(Models of area code CEL, CEK only)
This receiver also allows you to use RDS (Radio
Data System), which enables radio stations to
send additional information along with the
regular program signal. You can also display
RDS information.
Notes
• RDS is operable only for FM stations.
• Not all FM stations provide RDS service, nor do they
provide the same types of services. If you are not
familiar with the RDS services in your area, check
with your local radio stations for details.
Amplifier Operation
2
Using the Radio Data
System (RDS)
Press TUNER FM/AM repeatedly to
select the FM or AM band.
Receiving RDS broadcasts
Simply select a station on the FM band
using Automatic tuning (page 21), Direct
tuning (page 21), or preset tuning
(page 23).
When you tune in a station that provides RDS
services, the RDS indicator lights up and the
program service name appears in the display.
Note
RDS may not work properly if the station you tuned to
is not transmitting the RDS signal properly or if the
signal strength is weak.
Displaying RDS information
While receiving an RDS station, press
DISPLAY repeatedly.
Each time you press the button, RDS
information on the display changes cyclically as
follows:
Program Service name t Frequency t
Program Type indicationa) t Radio Text
indicationb) t Current Time indication (in 24hour system) t Sound field currently applied
a)
b)
Type of program being broadcast (see page 24).
Text messages sent by the RDS station.
continued
23GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB04BSC_HT-DDW760-U.fm]
masterpage:Left
GB01COV_HT-DDW760-U.book Page 24 Tuesday, April 20, 2004 3:10 PM
Notes
• If there is an emergency announcement by
government authorities, “ALARM” flashes in the
display.
• When the message consists of 9 characters or more,
the message scrolls across the display.
• If a station does not provide a particular RDS service,
“NO XXXX” (such as “NO TEXT”) appears in the
display.
Program type
indication
Description
PHONE IN
Programs where members of the
public express their views by
phone or in a public forum
TRAVEL
Programs about travel. Not for
announcements that are located by
TP/TA
LEISURE
Programs on recreational
activities such as gardening,
fishing, cooking, etc.
Description of program types
Program type
indication
Description
JAZZ
Jazz programs
COUNTRY
Country music programs
NEWS
News programs
NATION M
AFFAIRS
Topical programs that expand on
current news
Programs featuring the popular
music of the country or region
OLDIES
Programs featuring oldies music
FOLK M
Folk music programs
INFO
Programs offering information on
a wide spectrum of subjects,
including consumer affairs and
medical advice
SPORT
Sports programs
EDUCATE
Educational programs, such as
“how-to” and advice programs
DRAMA
Radio plays and serials
CULTURE
Programs about national or
regional culture, such as language
and social concerns
SCIENCE
Programs about the natural
sciences and technology
VARIED
Other types of programs such as
celebrity interviews, panel games,
and comedy
POP M
Popular music programs
ROCK M
Rock music programs
EASY M
Easy Listening
LIGHT M
Instrumental, vocal, and choral
music
CLASSICS
Performances of major orchestras,
chamber music, opera, etc.
OTHER M
Music that does not fit into any
categories above, such as Rhythm
& Blues and Reggae
WEATHER
Weather information
FINANCE
Stock market reports and trading,
etc.
CHILDREN
Programs for children
SOCIAL
Programs about people and the
things that affect them
RELIGION
Programs of religious content
DOCUMENT
Investigative features
NONE
Any programs not defined above
24GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB04BSC_HT-DDW760-U.fm]
masterpage:Right
GB01COV_HT-DDW760-U.book Page 25 Tuesday, April 20, 2004 3:10 PM
Changing the display
Amplifier Operation
Changing the information in
the display
You can check the sound field etc. by changing
the information in the display.
Press DISPLAY repeatedly.
Each time you press DISPLAY, the display will
change cyclically as follows.
Index name of the input* t Selected input t
Sound field currently applied
When the tuner is selected
Program Service name** or preset station name*
t Frequency t Program Type indication**
t Radio Text indication** t Current Time
indication (in 24-hour system)** t Sound field
currently applied
* Index name appears only when you have assigned
one to the input or preset station (page 34). Index
name does not appear when only blank spaces have
been entered, or it is the same as the input name.
** During RDS reception only. (Models of area code
CEL, CEK only. See page 23).
Adjusting the brightness of
the display
Press DIMMER repeatedly.
The brightness of the display will change in 3
steps.
25GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB04BSC_HT-DDW760-U.fm]
masterpage:Left
GB01COV_HT-DDW760-U.book Page 26 Tuesday, April 20, 2004 3:10 PM
About the indications in the display
1
SW
2
3
L F E SP
4
5
6
; DIGITAL ;PRO LOGIC II DTS
SLEEP OPT COAX
7
D.RANGE
RDS MEMORY
STEREO MONO
L C R
SL S SR
qs
qa
0 9
A SW: Lights up when the audio signal is output
from the SUB WOOFER jack.
B LFE: Lights up when the disc being played
back contains the LFE (Low Frequency
Effect) channel and the LFE channel signal is
actually being reproduced.
C SP: Lights up when you turn on the receiver.
Turns off when you connect headphones to the
PHONES jack.
D ; DIGITAL: Lights up when the receiver is
decoding signals recorded in the Dolby Digital
format.
E ; PRO LOGIC II: “; PRO LOGIC” lights
up when the receiver applies Pro Logic
processing to 2 channel signals in order to
output the center and surround channel
signals. “; PRO LOGIC II” lights up when
the Pro Logic II Movie/Music decoder is
activated.
Note
Dolby Pro Logic and Dolby Pro Logic II
decoding do not function for DTS format signals.
F DTS: Lights up when DTS signals are input.
8
I COAX: Lights up when the source signal is a
digital signal being input through the
COAXIAL terminal.
J OPT: Lights up when the source signal is a
digital signal being input through the
OPTICAL terminal.
K SLEEP: Lights up when sleep timer is
activated.
L Playback channel indicators: The letters
(L, C, R, etc.) indicate the channels being
played back. The boxes around the letters vary
to show how the receiver downmixes the
source sound.
L (Front Left), R (Front Right), C (Center
(monaural)), SL (Surround Left), SR
(Surround Right), S (Surround (monaural or
the surround components obtained by Pro
Logic processing))
Example:
Recording format (Front /Surround): 3/2
Sound Field: A.F.D. AUTO
L C R
SL
SR
Note
When playing a DTS format disc, be sure that you
have made digital connections and that INPUT
MODE is not set to “ANALOG” (page 30).
G Tuner indicators: Lights up when using the
receiver to tune in radio stations, etc. See
pages 21–24 for tuner operations.
Note
“RDS” appears for models of area code CEL,
CEK only.
H D.RANGE: Lights up when dynamic range
compression is activated (page 31).
26GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB05SND_HT-DDW760-U.fm]
masterpage:Right
GB01COV_HT-DDW760-U.book Page 27 Tuesday, April 20, 2004 3:10 PM
Enjoying Surround Sound
Using only the front
speakers and sub woofer
— 2CH STEREO
— AUTO FORMAT DIRECT
The Auto Format Direct (A.F.D.) mode allows
you to select the decoding mode you want for
your audio sound.
A.F.D. mode
(Display)
Decoding mode
A.F.D. AUTO
(A.F.D. AUTO)
As encoded
PRO LOGIC
(DOLBY PL)
Dolby Pro Logic
PRO LOGIC II MOVIE
(PLII MOV)
Dolby Pro Logic II
PRO LOGIC II MUSIC
(PLII MUS)
Enjoying Surround Sound
In this mode, the receiver outputs the sound
from the front left/right speakers and sub woofer
only.
When multi channel surround formats are input,
the signals are downmixed to 2 channel with
bass frequencies being output from the sub
woofer.
When standard 2 channel stereo sources are
input, the receiver’s bass redirection circuitry
will be activated. The front channel bass
frequencies will be output from the sub woofer.
Enjoying higher fidelity
sound
Press 2CH.
“2CH ST.” appears in the display and the
receiver switches to the 2CH STEREO mode.
Decoding the input audio
signal automatically
In this mode, the receiver automatically detects
the type of audio signal being input (Dolby
Digital, DTS, standard 2 channel stereo, etc.)
and performs the proper decoding if necessary.
This mode presents the sound as it was recorded/
encoded, without adding any surround effects.
However, if there are no low frequency signals
(Dolby Digital LFE, etc.) it will generate a low
frequency signal for output to the sub woofer.
Press A.F.D. repeatedly to select “A.F.D.
AUTO”.
The receiver automatically detects the type of
audio signal being input and performs the proper
decoding if necessary.
continued
27GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB05SND_HT-DDW760-U.fm]
masterpage:Left
GB01COV_HT-DDW760-U.book Page 28 Tuesday, April 20, 2004 3:10 PM
Enjoying stereo sound in multi
channel (2 channel decoding
mode)
This mode lets you specify the type of decoding
for 2 channel audio sources. This receiver can
reproduce 2 channel sound in 5 channels
through Dolby Pro Logic II or 4 channels
through Dolby Pro Logic.
Selecting a sound field
You can take advantage of surround sound
simply by selecting one of the receiver’s preprogrammed sound fields. They bring the
exciting and powerful sound of movie theaters
and concert halls into your home.
Press A.F.D. repeatedly to select the 2
channel decoding mode.
Selecting a sound field for
movies
The selected type of decoding appears in the
display.
Press MOVIE repeatedly to select the
sound field you want.
x DOLBY PL (PRO LOGIC)
The selected sound field appears in the display.
Performs Dolby Pro Logic decoding. The source
recorded in 2 channel is decoded into 4.1 channels.
Sound field
Display
CINEMA STUDIO EX A DCS
C.ST.EX A
x PLII MOV (PRO LOGIC II MOVIE)
Performs Dolby Pro Logic II Movie mode decoding.
This setting is ideal for movies encoded in Dolby
Surround. In addition, this mode can reproduce sound
in 5.1 channel when watching videos of overdubbed or
old movies.
x PLII MUS (PRO LOGIC II MUSIC)
Performs Dolby Pro Logic II Music mode decoding.
This setting is ideal for normal stereo sources such as
CDs.
Note
Dolby Pro Logic and Dolby Pro Logic II decoding do
not function for DTS format signals.
CINEMA STUDIO EX B DCS
C.ST.EX B
CINEMA STUDIO EX C DCS
C.ST.EX C
About DCS (Digital Cinema
Sound)
Sound fields with DCS marks use DCS
technology.
DCS is the concept name of the surround
technology for home theater developed by Sony.
DCS uses the DSP (Digital Signal Processor)
technology to reproduce the sound
characteristics of an actual cinema cutting studio
in Hollywood.
When played at home, DCS will create a
powerful theater effect that mimics the artistic
combination of sound and action as envisioned
by the movie director.
x C.ST.EX A (CINEMA STUDIO EX A) DCS
Reproduces the sound characteristics of the Sony
Pictures Entertainment “Cary Grant Theater” cinema
production studio. This is a standard mode, great for
watching most any type of movies.
x C.ST.EX B (CINEMA STUDIO EX B) DCS
Reproduces the sound characteristics of the Sony
Pictures Entertainment “Kim Novak Theater” cinema
production studio. This mode is ideal for watching
science-fiction or action movies with lots of sound
effects.
28GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB05SND_HT-DDW760-U.fm]
masterpage:Right
GB01COV_HT-DDW760-U.book Page 29 Tuesday, April 20, 2004 3:10 PM
x C.ST.EX C (CINEMA STUDIO EX C) DCS
Reproduces the sound characteristics of the Sony
Pictures Entertainment scoring stage. This mode is
ideal for watching musicals or films where orchestra
music is featured in the soundtrack.
About CINEMA STUDIO EX modes
Notes
• The effects provided by the virtual speakers may
cause increased noise in the playback signal.
• When listening with sound fields that employ the
virtual speakers, you will not be able to hear any
sound coming directly from the surround speakers.
Press MUSIC repeatedly to select the
sound field you want.
The selected sound field appears in the display.
Sound field
Display
HALL
HALL
JAZZ CLUB
JAZZ
LIVE CONCERT
CONCERT
x HALL
Reproduces the acoustics of a classical concert hall.
x JAZZ (JAZZ CLUB)
Reproduces the acoustics of a jazz club.
x CONCERT (LIVE CONCERT)
Reproduces the acoustics of a 300-seat live house.
Enjoying Surround Sound
CINEMA STUDIO EX modes are suitable for
watching motion picture DVDs (etc.), with
multi channel surround effects. You can
reproduce the sound characteristics of Sony
Pictures Entertainment’s dubbing studio in your
home.
The CINEMA STUDIO EX modes consist of
the following three elements.
• Virtual Multi Dimension
Creates 5 sets of virtual speakers from a single
pair of actual surround speakers.
• Screen Depth Matching
Creates the sensation that the sound is coming
from inside the screen like in theaters.
• Cinema Studio Reverberation
Reproduces the type of reverberation found in
theaters.
The CINEMA STUDIO EX modes integrate
these three elements simultaneously.
Selecting a sound field for
music
To turn off the surround effect
Press 2CH to select “2CH ST.” or press A.F.D.
repeatedly to select “A.F.D. AUTO”.
Tips
• The receiver lets you apply the last selected sound
field to an input whenever it is selected (Sound Field
Link). For example, if you select HALL for the CD
input, then change to a different input and then return
to CD, HALL will automatically be applied again.
• You can identify the encoding format of DVD
software, etc. by looking at the logo on the package.
–
: Dolby Digital discs
–
: Dolby Surround encoded
programs
–
: DTS Digital Surround encoded programs
Note
Sound fields do not function for the signals with a
sampling frequency of more than 48 kHz.
29GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB06ADV_HT-DDW760-U.fm]
masterpage:Left
GB01COV_HT-DDW760-U.book Page 30 Tuesday, April 20, 2004 3:10 PM
Advanced Adjustments and Settings
Switching the audio input
mode for digital
components
— INPUT MODE
You can switch the audio input mode for
components which have digital audio input
jacks.
1
2
Press input buttons to select the input.
Press INPUT MODE repeatedly to
select the audio input mode.
The selected audio input mode appears in
the display.
Audio input modes
• AUTO IN
Gives priority to digital signals when there are
both digital and analog connections. If there
are no digital signals, analog is selected.
• COAX IN
Specifies the digital audio signals input to the
DIGITAL COAXIAL input jack.
• OPT IN
Specifies the digital audio signals input to the
DIGITAL OPTICAL input jacks.
• ANALOG
Specifies the analog audio signals input to the
AUDIO IN (L/R) jacks.
Note
When signals with a sampling frequency of more than
48 kHz is input, the tone and sound field cannot be
used.
Customizing sound fields
By adjusting the LEVEL menu, you can
customize the sound fields to suit your particular
listening situation.
Note on the displayed items
The setup items you can adjust in each menu vary
depending on the sound field. Certain setup parameters
may be dimmed in the display. This means that the
selected parameter is either unavailable or fixed and
unchangeable.
Adjusting the LEVEL menu
You can adjust the balance and level of each
speaker. These settings are applied to all sound
fields except for the effect level parameter. The
effect level parameter settings are stored
individually for each sound field.
1
2
3
Start playing a source encoded with
multi channel surround effects (DVD,
etc.).
Press MAIN MENU repeatedly to select
“ LEVEL ”.
Press
or
repeatedly to select the
parameter you want to adjust.
For details, see “LEVEL menu parameters”
below.
4
While monitoring the sound, press + or
– repeatedly to select the setting you
want.
The setting is entered automatically.
5
Repeat steps 3 and 4 to adjust the other
parameters.
LEVEL menu parameters
The initial setting is underlined.
x
L
R
BAL. L/R XX
(Front speaker balance)
Initial setting: BALANCE (0)
Lets you adjust the balance between front left and right
speakers. You can adjust in the range of BAL. L (+1 to
+8), BALANCE (0), BAL. R (+1 to +8) in 17 steps.
30GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB06ADV_HT-DDW760-U.fm]
masterpage:Right
GB01COV_HT-DDW760-U.book Page 31 Tuesday, April 20, 2004 3:10 PM
x CTR XXX dB
(Center speaker level)
x SUR.L. XXX dB
(Surround speaker (left) level)
x SUR.R. XXX dB
(Surround speaker (right) level)
x S.W. XXX dB
(Sub woofer level)
x
Use the buttons on the receiver for the operation.
1
2
Press ?/1 to turn off the power.
While holding down 2CH, press
?/1.
“SF. CLR.” appears in the display and all
sound fields are reset to the initial setting.
Advanced Adjustments and Settings
Initial setting: 0 dB
You can adjust from –10 dB to +10 dB in 1 dB steps.
Resetting sound fields to the
initial settings
D.RANGE
COMP. XXX
(Dynamic range compressor)
Lets you compress the dynamic range of the sound
track. This may be useful when you want to watch
movies at low volumes late at night.
• OFF
The dynamic range is not compressed.
• STD
The dynamic range is compressed as intended by the
recording engineer.
• MAX
The dynamic range is compressed dramatically.
Tip
Dynamic range compressor lets you compress the
dynamic range of the soundtrack based on the dynamic
range information included in the Dolby Digital signal.
We recommend using the “MAX” setting. This greatly
compresses the dynamic range and lets you view
movies late at night at low volumes. Unlike analog
limiters, the levels are predetermined and provide a
very natural compression.
Note
Dynamic range compression is possible with Dolby
Digital sources only.
x EFCT. XXX (Effect level)
Initial setting: STD
Lets you adjust the “presence” of the surround effect.
31GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB06ADV_HT-DDW760-U.fm]
masterpage:Left
GB01COV_HT-DDW760-U.book Page 32 Tuesday, April 20, 2004 3:10 PM
Adjusting the tone
You can adjust the tonal quality (bass, treble
level) of the front speaker using the TONE
menu.
1
2
3
Start playing a source encoded with
multi channel surround effects (DVD,
etc.).
Press MAIN MENU repeatedly to select
“ TONE ”.
5
Using the CUSTOMIZE menu
to adjust the receiver
You can adjust various receiver settings using
the CUSTOMIZE menu.
1
2
Press
or
repeatedly to select the
parameter you want to adjust.
For details, see “TONE menu parameters”
below.
4
Advanced settings
While monitoring the sound, press + or
– repeatedly to select the setting you
want.
Press MAIN MENU repeatedly to select
“ CUSTOM ”.
Press
or
repeatedly to select the
parameter you want to adjust.
For details, see “CUSTOMIZE menu
parameters” below.
3
Press + or – repeatedly to select the
setting you want.
The setting is entered automatically.
The setting is entered automatically.
4
Repeat steps 3 and 4 to adjust the other
items.
CUSTOMIZE menu parameters
Repeat steps 2 and 3 to adjust the other
items.
Note
The initial setting is underlined.
You cannot adjust the tone when the receiver is
decoding signals with a sampling frequency of more
than 48 kHz.
x DEC. XXXX
(Digital audio input decoding priority)
TONE menu parameters
x BASS XX dB
(Front speaker bass level)
x TREB. XX dB
(Front speaker treble level)
Initial setting: 0 dB
You can adjust from –6 dB to +6 dB in 1 dB steps.
Lets you specify the input mode for the digital signal
input to the DIGITAL IN jacks.
The initial setting is “DEC. AUTO” for VIDEO 2 and
“DEC. PCM” for DVD.
• AUTO
Automatically switches the input mode between
DTS, Dolby Digital, or PCM.
• PCM
PCM signals are given priority (to prevent the
interruption when playback starts). Even when other
signals are input, the sound is output. However, this
receiver cannot decode DTS-CD when set to “DEC.
PCM”.
Note
When set to “DEC. AUTO” and the sound from the
digital audio jacks (for CD, etc.) is interrupted when
playback starts, set to “DEC. PCM”.
32GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB06ADV_HT-DDW760-U.fm]
masterpage:Right
GB01COV_HT-DDW760-U.book Page 33 Tuesday, April 20, 2004 3:10 PM
x DUAL XXX
(Digital broadcast language selection)
Advanced Adjustments and Settings
Lets you select the language you want to listen to
during digital broadcast. This feature only functions
for Dolby Digital sources.
• M/S (Main/Sub)
Sound of the main language will be output through
the front left speaker and sound of the sub language
will be output through the front right speaker
simultaneously.
• M (Main)
Sound of the main language will be output.
• S (Sub)
Sound of the sub language will be output.
• M+S (Main + Sub)
Mixed sound of both the main and sub languages will
be output.
x NAME IN
(Naming preset stations and inputs)
Lets you set the name of preset stations and inputs
selected with input buttons. For details, see “Naming
preset stations and inputs” on page 34.
33GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB070TH_HT-DDW760-U.fm]
masterpage:Left
GB01COV_HT-DDW760-U.book Page 34 Tuesday, April 20, 2004 3:10 PM
Note (Models of area code CEL, CEK only)
Other Operations
Naming preset stations
and inputs
When you name an RDS station and tune in the station,
the Program Service name appears instead of the name
you entered. (You cannot change the name of a
Program Service name. The name you entered will be
overwritten by the Program Service name.)
You can enter a name of up to 8 characters for
preset stations and inputs selected with input
buttons, and display it in the receiver’s display.
1
To index a preset station
Press TUNER FM/AM repeatedly to
select the FM or AM band, then tune in
the preset station you want to create an
index name for (page 23).
To index an input
Press the input button to select the
input you want to create an index name
for.
2
3
4
Press MAIN MENU repeatedly to select
“ CUSTOM ”.
Press
or
“NAME IN”.
repeatedly to select
Press ENTER.
The cursor flashes and you can select a
character.
5
Use
or
and + or – to create an
index name.
Press + or – repeatedly to select a character,
then press > to move the cursor to the next
position.
Tips
• You can select the character type as follows by
pressing + or – repeatedly.
Alphabet (upper case) t Numbers t Symbols
• To enter a blank space, press + or – repeatedly
until a blank space appears in the display.
• If you made a mistake, press < or > repeatedly
until the character you want to change flashes,
then press + or – repeatedly to select the correct
character.
6
Press ENTER to store the index name.
34GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB070TH_HT-DDW760-U.fm]
masterpage:Right
GB01COV_HT-DDW760-U.book Page 35 Tuesday, April 20, 2004 3:10 PM
Using the Sleep Timer
You can set the receiver to turn off automatically
at a specified time. Use the remote for the
operation.
1
2
Press ALT to light up the button.
Press SLEEP while the power is on.
Tip
To check the remaining time before the receiver turns
off, press ALT to light up the button (page 38), then
press SLEEP. The remaining time appears in the
display. If you press SLEEP again, the sleep timer will
be canceled.
Before you begin, make sure you have
connected all components properly.
Recording on an audio tape or
MiniDisc
You can record on a cassette tape or MiniDisc
using the receiver. See the operating instructions
of your cassette deck or MD deck if you need
help.
1
2
Select the component to be recorded.
Prepare the component for playing.
For example, insert a CD into the CD
player.
3
4
Insert a blank tape or MD into the
recording deck and adjust the
recording level, if necessary.
Other Operations
Each time you press SLEEP, the display
changes cyclically as follows:
2-00-00 t 1-30-00 t 1-00-00 t
0-30-00 t OFF
While using Sleep Timer, “SLEEP” lights up in
the display.
Recording
Start recording on the recording deck,
then start playback on the playback
component.
Notes
• Sound adjustments do not affect the signal output
from the MD/TAPE OUT jacks.
• The analog audio signals of the current input is
output from the MD/TAPE OUT jacks.
• (Models of area code CEL, CEK only) The signals
input to the MULTI CH IN jacks are not output from
the MD/TAPE OUT jacks even when MULTI CH IN
is being used. The analog audio signals of the current
or previously used input are output.
continued
35GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB070TH_HT-DDW760-U.fm]
masterpage:Left
GB01COV_HT-DDW760-U.book Page 36 Tuesday, April 20, 2004 3:10 PM
Recording on a video tape
You can record from a VCR, a TV or a DVD
using the receiver. You can also add audio from
a variety of audio sources when editing a video
tape. See the operating instructions of your VCR
or DVD player if you need help.
1
2
Select the program source to be
recorded.
Prepare the component for playing.
For example, insert a video tape you want to
record into VCR.
3
4
Insert a blank video tape into the VCR
(VIDEO 1) for recording.
Start recording on the recording VCR,
then start playing the video tape or
DVD you want to record.
Tip
You can record the sound from any audio source onto
a video tape while copying from a video tape or DVD.
Locate the point where you want to start recording
from another audio source, select the program source,
then start playback. The audio from that source will be
recorded onto the audio track of the video tape instead
of the audio from the original medium. To resume
audio recording from the original medium, select the
video source again.
Notes
• You cannot record a digital audio signal using a
component connected to the analog VIDEO 1 OUT
jacks.
• Make sure to make both digital and analog
connections to the VIDEO 2 and DVD inputs.
Analog recording is not possible if you make only
digital connections.
• The analog audio signals of the current input are
output from the VIDEO 1 OUT jacks.
• (Models of area code CEL, CEK only) The signals
input to the MULTI CH IN jacks are not output from
VIDEO 1 OUT jacks even when MULTI CH IN is
being used. The analog audio signals of the current or
previously used input are output.
36GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB08REM_HT-DDW760-U.fm]
masterpage:Right
GB01COV_HT-DDW760-U.book Page 37 Tuesday, April 20, 2004 3:10 PM
Operations Using the Remote RM-PP760
You can use the remote RM-PP760 to operate
the components in your system.
Before you use your
remote
Inserting batteries into the
remote
1
2
3
4
TV ?/1
?/1
AV ?/1
RM SET UP P
e;
wl
SYSTEM STANDBY SLEEP
VIDEO1
VIDEO2
AV1
AV2
DVD
MD/TAPE
CD
TUNER
5
6
wk
wj
2CH
A.F.D.
MOVIE
1
2
MUSIC
wh
3
DUAL
MONO
7
4
5
AUDIO
7
8
Notes
• Do not leave the remote in an extremely hot or humid
place.
• Do not use a new battery with an old one.
• Do not expose the remote sensor to direct sunlight or
lighting apparatuses. Doing so may cause a
malfunction.
• If you don’t use the remote for an extended period of
time, remove the batteries to avoid possible damage
from battery leakage and corrosion.
8
PRESET/
CH/D.SKIP
9
SUBTITLE
wg
ENTER
>
.
wf
wd
ws
wa
0/10
>10/11
12
ALT
SHIFT D.TUNING DISC
Tip
Under normal conditions, the batteries should last for
about 6 months. When the remote no longer operates
the receiver, replace all batteries with new ones.
6
JUMP/
TIME
ANGLE
9
m
ANT
q;
qa
-
M
CLEAR SEARCH MODE
X
H
x
MUTING
TOP MENU/
GUIDE
AV MENU
MASTER
VOL
V
qs
B
b
ENTER
ql
v
DISPLAY
TV VOL
w;
Operations Using the Remote RM-PP760
Insert R6 (size-AA) batteries with the + and –
properly oriented in the battery compartment.
When using the remote, point it at the remote
sensor
on the receiver.
Remote button
description
O
RETURN/EXIT
TV CH
qd
TV/
VIDEO
MAIN
MENU
WIDE
TEST
TONE
qk
qj
qh
qg
qf
The tables below show the settings of each
button.
Remote
Button
Operations Function
A.F.D. 7
Receiver
Selects the decoding
mode for audio sound.
continued
37GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB08REM_HT-DDW760-U.fm]
masterpage:Left
GB01COV_HT-DDW760-U.book Page 38 Tuesday, April 20, 2004 3:10 PM
Remote
Button
Operations
Function
Remote
Button
ALT wd
Remote
When ALT button
lights up, it changes
the remote key
function to activate
those buttons with
orange printing.
ENTER wf TV/VCR/
Satellite tuner/
LD player/
MD deck/
DAT deck/
Tape deck
ANGLE 7
DVD player
Selects viewing angle
or changes the angles.
ANT 9
VCR
Selects output signal
from the antenna
terminal: TV signal or
VCR program.
ENTER qs VCR/
Enters the selection.
Satellite tuner/
DVD player
AUDIO 7
AV MENU
qs
TV/VCR/
DVD player
Changes the sound to
Multiplex, Bilingual
or Multi channel TV
Sound.
Displays menu.
VCR/
Satellite tuner/
DVD player
AV1 4 and
AV2 3
Remote
AV ?/1 wl
TV/VCR/
Turns the audio and
CD player/
video components on
VCD player/ or off.
LD player/
DVD player/
MD deck/
DAT deck
Select the command
mode of the remote.
Operations
Function
After selecting a
channel, disc or track
using the numeric
buttons, press to enter
the value.
JUMP/
TIME 7
CD player/
VCD player/
DVD player
Shows the time or
displays the playing
time of disc, etc.
MAIN
MENU qj
Receiver
Selects the menu of the
receiver.
MASTER
VOL +/–
ql
Receiver
Adjusts the master
volume of the receiver.
MD/TAPE
6
Receiver
To listen to Minidisc or
audio tape.
MOVIE 7 Receiver
Selects the preprogrammed sound
fields for movie.
MUSIC wh Receiver
Selects the preprogrammed sound
fields for music.
MUTING
w;
Receiver
Mutes the sound from
the receiver.
Receiver
Selects preset stations.
CD wj
Receiver
To listen to compact
disc.
PRESET/
CH/
CLEAR 9
DVD player
Press if you make a
mistake when you
press the numeric
button or press to
return to continuous
play etc.
D.SKIP +/– TV/VCR/
Selects preset channels.
wg
Satellite tuner
Selects a disc directly
(multi-disc changer
only).
RETURN/
EXIT qs
DISC ws
CD player/
VCD player
DISPLAY
qs
TV/VCR/
Selects information
VCD player/ displayed on the TV
LD player/
screen.
DVD player
D.TUNING
9
Receiver
Enters direct tuning
mode.
DUAL
MONO 7
Receiver
Selects the language
you want during
digital broadcast.
DVD 5
Receiver
To watch DVD.
CD player/
Skips discs (multi-disc
VCD player/ changer only).
DVD player/
MD deck
VCD player/
LD player/
DVD player
Returns to the previous
menu.
Satellite tuner Exits the menu.
RM SET
UP 1
Remote
To set up the remote.
SEARCH
MODE ws
DVD player
Selects searching mode.
Press to select the unit
for search (track, index,
etc.)
SHIFT 9
Receiver
Selects a memory page
for presetting radio
stations or tuning to
preset stations.
38GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB08REM_HT-DDW760-U.fm]
masterpage:Right
GB01COV_HT-DDW760-U.book Page 39 Tuesday, April 20, 2004 3:10 PM
Remote
Button
Operations
Function
Remote
Button
Operations
Function
SLEEP e;
Receiver
Activates the sleep
function and the
duration which the
receiver turns off
automatically.
V/v qs
Receiver
Selects a menu item.
B/b qs
Receiver
Adjusts or changes the
setting.
DVD player
SYSTEM
STANDBY
(Press AV
?/1 wl and
?/1 e; at
the same
time)
Receiver/TV/ Turns off the receiver
VCR/Satellite and other Sony audio/
tuner/
video components.
CD player/
VCD player/
LD player/
DVD player/
MD deck/
DAT deck
TEST
TONE qh
Receiver
TOP MENU/ DVD player
Changes the subtitles.
Satellite tuner Displays guide menu.
Receiver
To listen to radio
programs.
TV CH +/–
qf
TV
Selects preset TV
channels.
TV/VIDEO
qk
TV
Selects input signal:
TV input or video
input.
TV
Adjusts the volume of
the TV.
Turns the TV on or off.
VIDEO1 4 Receiver
To watch VCR.
(VTR mode 3)
VIDEO2 3 Receiver
To watch VCR.
(VTR mode 1)
WIDE qg
TV
Selects the wide
picture mode.
?/1 e;
Receiver
Turns the receiver on
or off.
2CH 7
Receiver
Selects 2CH STEREO
mode.
Receiver
Use with SHIFT to
preset radio station or
tuning to preset
stations and with
D.TUNING for direct
tuning.
CD player/
VCD player/
LD player/
MD deck/
DAT deck
Selects track numbers.
0/10 selects track 10.
TV/VCR/
Selects channel
Satellite tuner numbers.
Displays DVD title.
TUNER wk
TV ?/1 2
1-9 7 and
0/10 8
Outputs test tone.
GUIDE qs
TV VOL +/– TV
qd
V/v/B/b qs VCR/
Selects a menu item.
Satellite tuner/
DVD player
>10/11 8
CD player/
VCD player/
LD player/
MD deck
Selects track numbers
over 10.
./>
8
VCR/
CD player/
VCD player/
LD player/
DVD player/
MD deck/
DAT deck/
Tape deck
Skips tracks.
m/M 9 CD player/
VCD player/
LD player/
DVD player/
MD deck
VCR/
DAT deck/
Tape deck
Searches tracks in the
forward or backward
direction.
Operations Using the Remote RM-PP760
SUBTITLE
8
Fastforwards or
rewinds.
continued
39GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB08REM_HT-DDW760-U.fm]
masterpage:Left
GB01COV_HT-DDW760-U.book Page 40 Tuesday, April 20, 2004 3:10 PM
Remote
Button
Operations
Function
H q;
VCR/
CD player/
VCD player/
LD player/
DVD player/
MD deck/
DAT deck/
Tape deck
Starts playback.
VCR/
CD player/
VCD player/
LD player/
DVD player/
MD deck/
DAT deck/
Tape deck
Pauses playback or
record. (Also starts
recording with
components in
recording standby.)
VCR/
CD player/
VCD player/
LD player/
DVD player/
MD deck/
DAT deck/
Tape deck
Stops playback.
VCD player/
LD player/
DVD player
Returns to the
previous menu or exits
the menu.
TV
Selects the channel
entry mode, either one
or two digit.
X qa
x wa
O qs
-/-- ws
Selecting the command
mode of the remote
Set the remote command mode using the RM
SET UP button and the remote command mode
buttons.
Selecting the command mode
You can switch the command mode (AV1 and
AV2) of the remote. If the command mode of
the receiver and the remote is different, you
cannot use the remote to operate the receiver.
Press AV1 or AV2 while holding down RM
SET UP.
The indicator flashes once (twice for AV2), then
the command mode switches.
To check the command mode of
the remote
Press RM SET UP. You can check the remote by
the indicator.
Notes
• Some functions explained in this section may not
work depending on the model.
• The above explanation is intended to serve as an
example only. Therefore, depending on the
component the above operation may not be possible
or may operate differently than described.
• When you press input buttons (VIDEO1, VIDEO2 or
DVD), the input mode of the TV might not switch to
the corresponding input mode that you want. In this
case, press TV/VIDEO button to switch the input
mode of the TV.
• To activate the buttons with orange printing, press
ALT first before pressing the buttons.
Mode
Indicator flashes
AV1
once
AV2
twice
To reset the remote to factory
settings
Press ?/1, AV ?/1 and MASTER VOL – at
the same time.
The indicator flashes 3 times, then goes off.
Note
If the command mode of the receiver and the remote is
different, you cannot use the remote to operate the
receiver. To change the command mode of the
receiver, see page 46.
40GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB08REM_HT-DDW760-U.fm]
masterpage:Right
GB01COV_HT-DDW760-U.book Page 41 Tuesday, April 20, 2004 3:10 PM
Programming the remote
You can program the remote to control nonSony components by changing the code. Once
the control signals have been memorized, you
can use those components as part of your
system.
Furthermore, you can also program the remote
for Sony components that the remote is unable to
control. Note that the remote can only control
components that accept infrared wireless control
signals.
1
Press AV ?/1 while holding down RM
SET UP.
2
Press the input button (including TV
?/1) for the component you want to
control.
For example, if you are going to control a
CD player, press CD.
3
Press the numeric buttons to enter the
numeric code (or one of the codes if
more than one code exists)
corresponding to the component and
the maker of the component you want
to control.
See the tables on pages 42–43 for
information on the numeric code(s)
corresponding to the component and the
maker of the component (the first digit and
the last two digits of the numeric code
correspond to the category and the maker’s
code respectively).
4
Press the programmed button to activate the
input you want.
If programming is unsuccessful,
check the following:
• If the indicator does not light up in step 1, the
batteries are weak. Replace both batteries.
• If the indicator flashes 4 times in quick
succession while entering the numeric code,
an error has occurred. Start again from step 1.
Notes
• The indicator turns off while a valid button is
pressed.
• In step 2, if several input buttons are pressed, only the
last pressed button is valid.
• In step 2, if you press TV ?/1, only TV VOL +/– ,
TV CH +/– , TV/VIDEO and WIDE buttons are
reprogrammed.
• In step 3, if an input button is pressed, the new input
is selected and the programming procedure returns to
the beginning of step 3.
• For the numeric codes, only the first three numbers
entered are valid.
To clear the memory of the
remote
To clear all programmed signals, do the
following to reset the remote to factory settings.
Press ?/1, AV ?/1 and MASTER VOL – at
the same time.
Operations Using the Remote RM-PP760
The indicator lights up.
To activate the input after
programming
The indicator flashes 3 times, then goes off.
Press ENTER.
Once the numeric code has been verified,
the indicator slowly flashes twice and the
remote automatically exits the
programming mode.
5
Repeat steps 1 to 4 to control other
components.
To cancel programming
Press RM SET UP during any step. The remote
automatically exits the programming mode.
continued
41GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB08REM_HT-DDW760-U.fm]
masterpage:Left
GB01COV_HT-DDW760-U.book Page 42 Tuesday, April 20, 2004 3:10 PM
The numeric codes
corresponding to the component
and the maker of the component
To control a DAT deck
SONY
203
Use the numeric codes in the tables below to
control non-Sony components and also Sony
components that the remote is normally unable
to control. Since the remote signal that a
component accepts differs depending on the
model and year of the component, more than one
numeric code may be assigned to a component.
If you fail to program your remote using one of
the codes, try using other codes.
PIONEER
219
Maker
Code(s)
To control an MD deck
Maker
Code(s)
SONY
301
DENON
302
JVC
303
KENWOOD
304
Notes
• The numeric codes are based on the latest
information available for each brand. There is a
chance, however, that your component will not
respond to some or all of the codes.
• All of the input buttons on this remote may not be
available when used with your particular component.
To control a tape deck
Maker
Code(s)
SONY
201, 202
DENON
204, 205
KENWOOD
206, 207, 208, 209
To control a CD player
NAKAMICHI
210
Maker
Code(s)
PANASONIC
216
SONY
101, 102, 103
PHILIPS
211, 212
DENON
104, 123
PIONEER
213, 214
JVC
105, 106, 107
TECHNICS
215, 216
KENWOOD
108, 109, 110
YAMAHA
217, 218
MAGNAVOX
111, 116
MARANTZ
116
ONKYO
112, 113, 114
PANASONIC
115
Maker
Code(s)
PHILIPS
116
SONY
601, 602, 603
PIONEER
117
PIONEER
606
TECHNICS
115, 118, 119
YAMAHA
120, 121, 122
To control an LD player
To control a video CD player
Maker
Code(s)
SONY
605
42GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB08REM_HT-DDW760-U.fm]
masterpage:Right
GB01COV_HT-DDW760-U.book Page 43 Tuesday, April 20, 2004 3:10 PM
To control a VCR
To control a TV
Code(s)
Maker
Code(s)
SONY
701, 702, 703, 704, 705,
706
SONY
501, 502
DAEWOO
AIWA*
710, 750, 757, 758
504, 505, 506, 507, 515,
544
AKAI
707, 708, 709, 759
FISHER
508
BLAUPUNKT
740
GOLDSTAR
EMERSON
711, 712, 713, 714, 715,
716, 750
503, 511, 512, 515, 534,
544
GRUNDIG
517, 534
FISHER
717, 718, 719, 720
HITACHI
513, 514, 515, 544
GENERAL ELECTRIC
721, 722, 730
ITT/NOKIA
521, 522
GOLDSTAR
723, 753
JVC
516
GRUNDIG
724
MAGNAVOX
503, 518, 544
HITACHI
722, 725, 729, 741
MITSUBISHI/MGA
503, 519, 544
ITT/NOKIA
717
NEC
503, 520, 544
JVC
726, 727, 728, 736
PANASONIC
509, 524
MAGNAVOX
730, 731, 738
PHILIPS
515, 518
MITSUBISHI/MGA
732, 733, 734, 735
PIONEER
509, 525, 526, 540
NEC
736
RCA/PROSCAN
510, 527, 528, 529, 544
PANASONIC
729, 730, 737, 738, 739,
740
SAMSUNG
503, 515, 531, 532, 533,
534, 544
PHILIPS
729, 730, 731
SANYO
508, 545, 546, 547
PIONEER
729
SHARP
535
RCA/PROSCAN
722, 729, 730, 731, 741,
747
TELEFUNKEN
523, 536, 537, 538
THOMSON
530, 537, 539
SAMSUNG
742, 743, 744, 745
TOSHIBA
535, 540, 541
SANYO
717, 720, 746
ZENITH
542, 543
SHARP
748, 749
TELEFUNKEN
751, 752
TOSHIBA
747, 755, 756
To control a satellite tuner or
cable box
ZENITH
754
Maker
Code(s)
SONY
801, 802, 803, 804
JERROLD/G.I.
806, 807, 808, 809, 810,
811, 812, 813, 814
PANASONIC
818
* If an AIWA VCR does not work even though you
enter the code for AIWA, enter the code for Sony
instead.
To control a DVD player
RCA
805, 819
Maker
S. ATLANTA
815, 816, 817
Code(s)
SONY
401, 402, 403
PANASONIC
406, 408
To control a tuner
PHILIPS
407
Maker
Code(s)
PIONEER
409
SONY
002, 003, 004, 005
TOSHIBA
404
DENON
405
Operations Using the Remote RM-PP760
Maker
43GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB09ADD_HT-DDW760-U.fm]
masterpage:Left
GB01COV_HT-DDW760-U.book Page 44 Tuesday, April 20, 2004 3:10 PM
If you encounter color irregularity on a
nearby TV screen
Additional Information
Precautions
On safety
Should any solid object or liquid fall into the cabinet,
unplug the receiver and have it checked by qualified
personnel before operating it any further.
On power sources
• Before operating the receiver, check that the
operating voltage is identical with your local power
supply. The operating voltage is indicated on the
nameplate at the rear of the receiver.
• The receiver is not disconnected from the AC power
source (mains) as long as it is connected to the wall
outlet, even if the receiver itself has been turned off.
• If you are not going to use the receiver for a long
time, be sure to disconnect the receiver from the wall
outlet. To disconnect the AC power cord, grasp the
plug itself; never pull the cord.
• (Models of area code CA only)
One blade of the plug is wider than the other for the
purpose of safety and will fit into the wall outlet only
one way. If you are unable to insert the plug fully into
the outlet, contact your dealer.
• AC power cord must be changed only at the qualified
service shop.
The front and center speakers and the sub woofer are
magnetically shielded to allow it to be installed near
a TV set. However, color irregularities may still be
observed on certain types of TV sets. As the surround
speakers are not magnetically shielded, we
recommend that you place the surround speakers
slightly further away from TV set (page 14).
If color irregularity is observed...
Turn off the TV set once, then turn it on again after
15 to 30 minutes.
If color irregularity is observed again...
Place the speaker further away from the TV set.
If howling occurs
Reposition the speakers or turn down the volume on
the receiver.
On cleaning
Clean the cabinet, panel and controls with a soft cloth
slightly moistened with a mild detergent solution. Do
not use any type of abrasive pad, scouring powder or
solvent such as alcohol or benzine.
If you have any question or problem concerning your
receiver, please consult your nearest Sony dealer.
On heat buildup
Although the receiver heats up during operation, this is
not a malfunction. If you continuously use this receiver
at a large volume, the cabinet temperature of the top,
side and bottom rises considerably. To avoid burning
yourself, do not touch the cabinet.
On placement
• Place the receiver in a location with adequate
ventilation to prevent heat buildup and prolong the
life of the receiver.
• Do not place the receiver near heat sources, or in a
place subject to direct sunlight, excessive dust or
mechanical shock.
• Do not place anything on top of the cabinet that
might block the ventilation holes and cause
malfunctions.
• Use caution when placing the receiver or speakers on
surfaces that have been specially treated (with wax,
oil, polish, etc.) as staining or discoloration of the
surface may result.
On operation
Before connecting other components, be sure to turn
off and unplug the receiver.
44GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB09ADD_HT-DDW760-U.fm]
masterpage:Right
GB01COV_HT-DDW760-U.book Page 45 Tuesday, April 20, 2004 3:10 PM
Troubleshooting
If you experience any of the following
difficulties while using the receiver, use this
troubleshooting guide to help you remedy the
problem.
There is no sound from a specific component.
• Check that the component is connected correctly
to the audio input jacks for that component.
• Check that the cord(s) used for the connection is
(are) fully inserted into the jacks on both the
receiver and the component.
• Check that you have selected the correct
component on the receiver.
There is no sound from one of the front
speakers.
• Connect a pair of headphones to the PHONES
jack to verify that sound is output from the
headphones. If only one channel is output from the
headphones, the component may not be connected
to the receiver correctly. Check that all the cords
are fully inserted into the jacks on both the
receiver and the component. If both channels are
output from the headphones, the front speaker
may not be connected to the receiver correctly.
Check the connection of the front speaker which is
not outputting any sound.
There is no sound from analog 2 channel
sources.
• Check that the INPUT MODE is not set to
“COAX IN” or “OPT IN” (page 30).
• (Models of area code CEL, CEK only) Check that
you have not selected “MULTI CH IN”.
The left and right sounds are unbalanced or
reversed.
• Check that the speakers and components are
connected correctly and securely.
• Adjust balance parameters in the LEVEL menu.
There is severe hum or noise.
• Check that the speakers and components are
connected securely.
• Check that the connecting cords are away from a
transformer or motor, and at least 3 meters (10
feet) away from a TV set or fluorescent light.
• Move your TV away from the audio components.
• The plugs and jacks are dirty. Wipe them with a
cloth slightly moistened with alcohol.
Additional Information
There is no sound or only a very low-level
sound no matter which component is
selected.
• Check that the speakers and components are
connected securely and correctly.
• Check that both the receiver and all components
are turned on.
• Check that you have selected the correct
component on the receiver.
• Check that MASTER VOLUME –/+ is not set at
“VOL MIN”.
• Check that the headphones are not connected.
• Press MUTING on the remote to cancel the
muting function.
There is no sound from digital sources (from
COAXIAL or OPTICAL input jack).
• Check that the INPUT MODE is not set to
“ANALOG” (page 30). Check that the INPUT
MODE is not set to “COAX IN” for the sources
from OPTICAL input jack, or set to “OPT IN” for
the sources from COAXIAL input jack.
• (Models of area code CEL, CEK only) Check that
you have not selected “MULTI CH IN”.
There is no sound or only a very low-level
sound is heard from the center or/and
surround speakers.
• Make sure the sound field function is on (press
A.F.D., MOVIE or MUSIC).
• Select a CINEMA STUDIO EX mode (page 28).
• Adjust the speaker level (page 19).
There is no sound from the sub woofer.
• Check that the sub woofer is connected correctly
and securely.
The surround effect cannot be obtained.
• Make sure the sound field function is on (press
A.F.D., MOVIE or MUSIC).
• Sound fields do not function for the signals with a
sampling frequency of more than 48 kHz.
Dolby Digital or DTS multi channel sound is
not reproduced.
• Check that the playing DVD, etc. is recorded in
Dolby Digital or DTS format.
• When connecting the DVD player, etc. to the
digital input jacks of this receiver, check the audio
setting (settings for the audio output) of the
connected component.
continued
45GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB09ADD_HT-DDW760-U.fm]
masterpage:Left
GB01COV_HT-DDW760-U.book Page 46 Tuesday, April 20, 2004 3:10 PM
Recording cannot be done.
• Check that the components are connected
correctly.
• Select the source component with input buttons.
The FM reception is poor.
• Use a 75-ohm coaxial cable (not supplied) to
connect the receiver to an outdoor FM antenna as
shown below. If you connect the receiver to an
outdoor antenna, ground it against lightning. To
prevent a gas explosion, do not connect the ground
wire to a gas pipe.
Outdoor FM antenna
Receiver
ANTENNA
ANTENNA
AM
AM
Ground wire
(not supplied)
To ground
Radio stations cannot be tuned in.
• Check that the antennas are connected securely.
Adjust the antennas and connect an external
antenna if necessary.
• The signal strength of the stations is too weak
(when tuning in with automatic tuning). Use direct
tuning.
• Make sure you set the tuning interval correctly
(when tuning in AM stations with direct tuning).
• No stations have been preset or the preset stations
have been cleared (when tuning by scanning
preset stations). Preset the stations (page 22).
• Press DISPLAY repeatedly so that the frequency
appears in the display.
RDS does not work.*
• Make sure that you are tuned to an FM RDS
station.
• Select a stronger FM station.
The RDS information that you want does not
appear.*
• Contact the radio station and find out whether they
actually provide the service in question. If so, the
service may be temporarily out of order.
There is no picture or an unclear picture
appears on the TV screen or monitor.
• Select the appropriate input on the receiver.
• Set your TV to the appropriate input mode.
• Move your TV away from the audio components.
* Models of area code CEL, CEK only.
Remote control
The remote does not function.
• Point the remote at the remote sensor
on the
receiver.
• Remove any obstacles in the path between the
remote and the receiver.
• Replace all the batteries in the remote with new
ones, if they are weak.
• Check if the command modes of the receiver and
the remote is the same. If the command mode of
the receiver and the remote is different, you
cannot operate the receiver with the remote. To
switch the command mode of the receiver, press
?/1 to turn off the power. Then, press ?/1 while
pressing ENTER. Each time you press ?/1, the
command mode switches between
“C.MODE.AV2” and “C.MODE.AV1”. (The
initial setting is “C.MODE.AV2”.)
• Make sure you select the correct input on the
remote.
• To activate the buttons with orange printing, press
ALT first before pressing the buttons.
• Before you use the V/v/B/b button for receiver
operation, press MAIN MENU. To operate other
components, press TOP MENU/GUIDE or AV
MENU after pressing the input button.
Error message
If there is a malfunction, the display shows a
message.
PROTECT
Irregular current is output from the speakers. The
receiver will automatically turn off after a few
seconds. Check the speaker connection and turn on
the power again. If this problem persists, consult
your nearest Sony dealer.
46GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB09ADD_HT-DDW760-U.fm]
masterpage:Right
GB01COV_HT-DDW760-U.book Page 47 Tuesday, April 20, 2004 3:10 PM
If you are unable to remedy the
problem using the
troubleshooting guide
Clearing the receiver’s memory may remedy the
problem (page 17). However, note that all
memorized settings will be reset to their factory
settings and you will have to readjust all settings
on the receiver.
If the problem persist
Consult your nearest Sony dealer.
Reference sections for clearing
the receiver’s memory
To clear
See
All memorized settings
page 17
Customized sound fields
page 31
Specifications
Amplifier section
Power Output1)
Models of area code CA
(6 ohms 1 kHz, THD 0.7%)
STR-K760P:
FRONT2): 60 W/ch
CENTER2): 60 W
SURR2): 60 W/ch
(6 ohms 1 kHz, THD 10%)
STR-K760P:
FRONT2): 100 W/ch
CENTER2): 100 W
SURR2): 100 W/ch
Additional Information
Models of area code SP, E51
(6 ohms 1 kHz, THD 0.7%)
STR-K760P:
FRONT2): 80 W/ch
CENTER2): 80 W
SURR2): 80 W/ch
(6 ohms 1 kHz, THD 10%)
STR-K760P:
FRONT2): 100 W/ch
CENTER2): 100 W
SURR2): 100 W/ch
Models of area code CEL, CEK
(6 ohms 1 kHz, THD 0.7%)
STR-DE497P:
FRONT2): 80 W/ch
CENTER2): 80 W
SURR2): 80 W/ch
(6 ohms 1 kHz, THD 10%)
STR-DE497P:
FRONT2): 100 W/ch
CENTER2): 100 W
SURR2): 100 W/ch
Models of area code AU
(6 ohms 120 Hz–20 kHz, THD 0.09%)
STR-K760P:
FRONT2): 45 W/ch
CENTER2): 45 W
SURR2): 45 W/ch
(6 ohms 1 kHz, THD 0.7%)
STR-K760P:
FRONT2): 80 W/ch
CENTER2): 80 W
SURR2): 80 W/ch
(6 ohms 1 kHz, THD 10%)
STR-K760P:
FRONT2): 100 W/ch
CENTER2): 100 W
SURR2): 100 W/ch
continued
47GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB09ADD_HT-DDW760-U.fm]
masterpage:Left
GB01COV_HT-DDW760-U.book Page 48 Tuesday, April 20, 2004 3:10 PM
1) Measured under the following conditions:
AM tuner section
Area code
Power requirements
CA
120 V AC, 60 Hz
SP, CEL, CEK
230 V AC, 50 Hz
AU, E51
240 V AC, 50 Hz
Tuning range
Models of area code CA
With 10-kHz tuning scale: 530 - 1,710 kHz3)
With 9-kHz tuning scale: 531 - 1,710 kHz3)
Models of area code E51
With 10-kHz tuning scale: 530 - 1,610 kHz
Models of area code CEL, CEK, SP, AU
With 9-kHz tuning scale: 531 - 1,602 kHz
Antenna
Loop antenna
Intermediate Frequency 450 kHz
2) Depending on the sound field settings and the
source, there may be no sound output.
Inputs (Analog)
MULTI CH IN*, CD,
Sensitivity: 800 mV
MD/TAPE, VIDEO 1, 2, Impedance: 50 kiloohms
DVD
Inputs (Digital)
DVD (Coaxial)
Sensitivity: –
Impedance: 75 ohms
VIDEO 2 (Optical)
Sensitivity: –
Impedance: –
Outputs (Analog)
Voltage: 2 V
Impedance: 1 kiloohms
Reproduction frequency range:
28 – 20,000 Hz
Tone
Gain levels
Video section
Inputs/Outputs
Video:
1 Vp-p, 75 ohms
General
MD/TAPE (OUT),
Voltage: 800 mV
VIDEO 1 (AUDIO OUT) Impedance: 10 kiloohms
SUB WOOFER
3) You can change the AM tuning scale to 9 kHz or
10 kHz. After tuning in any AM station, turn off the
receiver. While holding down PRESET TUNING +
or TUNING +, press ?/1. All preset stations will be
erased when you change the tuning scale. To reset
the scale to 10 kHz (or 9 kHz), repeat the procedure.
Power requirements
Area code
Power requirements
CA
120 V AC, 60 Hz
CEL, CEK
230 V AC, 50/60 Hz
AU
240 V AC, 50 Hz
SP
220 – 230 V AC, 50/60 Hz
E51
120/220/240 V AC, 50/60 Hz
±6 dB, 1 dB step
Power consumption
* Models of area code CEL, CEK only.
FM tuner section
Tuning range
Antenna
Antenna terminals
Intermediate Frequency
87.5 - 108.0 MHz
FM wire antenna
75 ohms, unbalanced
10.7 MHz
Area code
Power consumption
CA
225 VA
CEL, CEK, AU, SP 150 W
E51
165 W
Power consumption (during standby mode)
0.3 W
Dimensions (w/h/d) (Approx.)
430 × 145 × 301.5 mm
(17 × 5 6/8 × 11 7/8 inches)
including projecting parts
and controls
Mass (Approx.)
6.5 kg (14 lb 6 oz)
48GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB09ADD_HT-DDW760-U.fm]
masterpage:Right
GB01COV_HT-DDW760-U.book Page 49 Tuesday, April 20, 2004 3:10 PM
Speaker section
Supplied accessories
Front speakers (SS-MSP760L/
SS-MSP760R)
Center speaker (SS-CNP760)
Surround speakers (SS-MSP760SL/
SS-MSP760SR)
FM wire antenna (1)
AM loop antenna (1)
Speaker connecting cord, long (2)
Speaker connecting cord, short (3)
Monaural connecting cord (1 phono to 1 phono) (1)
Coaxial digital cord (1)
Foot pads (speakers) (20)
Foot pads (subwoofer) (4)
Remote commander (1)
R6 (size-AA) batteries (2)
Speakers
• Front speakers (2)
• Center speaker (1)
• Surround speakers (2)
• Sub woofer (1)
Front/center speakers
For details on the area code of the component you
are using, see page 3.
Additional Information
Full range, magnetically
shielded
Surround speakers
Full range
Speaker units
80 mm cone type
Enclosure type
Bass reflex
Rated Impedance
6 ohms
Dimension (w/h/d) (Approx.)
Front/surround speakers 102 × 150 × 126 mm
(4 × 6 × 5 inches)
Center speaker
225 × 102 × 126 mm
(8 7/8 × 4 × 5 inches)
Mass (Approx.)
Front speakers
0.8 kg (1 lb 13 oz)
Center speaker
1.0 kg (2 lb 4 oz)
Surround speakers
0.7 kg (1 lb 9 oz)
Design and specifications are subject to change
without notice.
Sub woofer (SA-WMSP76)
Speaker system
Speaker unit
Enclosure type
RMS output:
Input
Active subwoofer,
magnetically shielded
200 mm cone type
Acoustically loaded bass
reflex
100 W (6 ohms, 100 Hz,
THD 10%)
LINE IN (input pin jacks)
Power requirements
Area code
Power requirements
CA
120 V AC, 60 Hz
CEL, CEK, SP
230 V AC, 50/60 Hz
AU
240 V AC, 50/60 Hz
E51
120/220~230 V AC, 50/60 Hz
Power consumption
75 W
Dimensions (w/h/d) (Approx.)
270 × 325 × 398 mm
(10 3/4 × 12 7/8 × 15 3/4
inches) including front
panel
Mass (Approx.)
9.0 kg (19 lb 14 oz)
49GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB09ADD_HT-DDW760-U.fm]
masterpage:Right
GB01COV_HT-DDW760-U.book Page 50 Tuesday, April 20, 2004 3:10 PM
List of button locations and reference pages
How to use pages 50 and 51
Use this page to find the location of buttons that are
mentioned in the text.
Illustration number
r
DISPLAY 2 (23, 25, 46)
R
Name of button/part
R
Reference page
Main unit
ALPHABETICAL ORDER
A-L
A.F.D. (button/indicator) 9 (27,
28, 29, 45)
CD wg (20)
DIMMER 3 (25)
DISPLAY 2 (23, 25, 46)
Display 5 (23, 25)
DVD wj (20)
ENTER qd (17, 34, 46)
FM MODE ws (21)
Input buttons qk (20, 30, 33, 34,
46)
INPUT MODE qf (26, 30)
IR (receptor) 4 (37, 46)
M-Z
MAIN MENU qj (17, 30, 32, 34)
MASTER VOLUME –/+ qs (19,
20, 45)
MD/TAPE wh (20)
MEMORY wa (22)
MOVIE (button/indicator) q;
(28, 45)
MULTI CH IN* 7 (20)
MULTI CHANNEL DECODING
(indicator)* 6 (20)
MUSIC (button/indicator) qa (29,
45)
PHONES (jack) wd (20, 26, 45)
PRESET TUNING –/+ ql (22,
48)
TUNER FM/AM wf (20, 21, 34)
TUNING –/+ w; (21, 48)
VIDEO 1 wl (20)
VIDEO 2 wk (20)
NUMBERS AND SYMBOLS
2CH (button/indicator) 8 (27,
29, 31)
+/– qg (17, 30, 32, 34)
</> qh (17, 30, 32, 34)
?/1 (power) 1 (17, 22, 46, 48)
* Models of area code CEL, CEK
only.
50GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB09ADD_HT-DDW760-U.fm]
masterpage:Right
GB01COV_HT-DDW760-U.book Page 51 Tuesday, April 20, 2004 3:10 PM
1
wd
ws wa
2 3
4
5
6
w;
ql
qk
qj qh qg
wk
wj
wh
wg
qfqd
qs
Additional Information
wl
7 8 9 q; qa
wf
51GB
model name1[HT-DDW760]
[4-252-086-13(1)]
lename[E:\SEM_Janet\DDW760_3rdrevision\J9040000_4252086131DDW760GB\4252086131\
GB01COV_HT-DDW760-UIX.fm]
masterpage:Left
GB01COV_HT-DDW760-U.book Page 52 Tuesday, April 20, 2004 3:10 PM
Index
A
R
Adjusting
CUSTOMIZE parameters 32
LEVEL parameter 30
SET UP parameters 17
speaker levels and balance 19
TONE parameter 32
Automatic tuning 21
RDS 23
Recording
on a video tape 36
on an audio tape or MD 35
C
Changing
display 25
Clearing receiver’s memory 17
CUSTOMIZE menu 32
D
Digital Cinema Sound 28
Direct tuning 21
Dual Mono 33
Dubbing. See Recording
S
Selecting
component 20
sound field 28–29
SET UP menu 17
Sleep Timer 35
Sound field
customizing 30
pre-programmed 28–29
resetting 31
selecting 28–29
Speakers
adjusting speaker levels and balance 19
connection 14
placement 14
Supplied accessories 49
E
Editing. See Recording
I
Indexing. See Naming
L
T
Test tone 19
TONE menu 32
Tuning
automatically 21
directly 21
to preset stations 22
Labeling. See Naming
LEVEL menu 30
N
Naming 34
P
Preset stations
how to 22
how to tune 23
Sony Corporation Printed in Malaysia
model name1[HT-DDW760]
[4-252-086-13(1)]
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement