Toshiba SD-6200 Multi

Toshiba SD-6200 Multi
OWNER'S MANUAL
DIGITAL VIDEO
DVD VIDEO PLAYER
SD-6200
Jun., 2000 s
Introduction
SAFETY PRECAUTIONS
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS
RISQUE DE CHOC ELECTRIQUE NE
PAS OUVRIR
WARNING :
TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USERSERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk
of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE
ENCLOSURE. DO NOT OPEN THE CABINET. REFER SERVICING TO QUALIFIED PERSONNEL
ONLY.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
ATTENTION:
POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA
FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
CAUTION:
This Digital Video Disc Player employs a Laser System.
To ensure proper use of this product, please read this owner’s manual carefully and retain for
future reference. Should the unit require maintenance, contact an authorized service location see service procedure.
Use of controls or adjustments or performance of procedures other than those specified herein
may result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open the enclosure.
Visible and invisible laser radiation when open and interlocks defeated.
DO NOT STARE INTO BEAM.
FCC NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rule. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
WARNING:
2
Changes or modifications made to this equipment, not expressly approved by Toshiba, or
parties authorized by Toshiba, could void the user’s authority to operate the equipment.
In the spaces provided below, record the Model and Serial No. located on the rear panel of your DVD video
player.
Serial No.
Introduction
Model No.
Retain this information for future reference.
Location of the required label
PRODUCT IS CERTIFIED BY THE MANUFACTURER TO
COMPLY WITH DHHS RULE 21 CFR SUBCHAPTER J
APPLICABLE AT THE DATE OF MANUFACTURE.
MANUFACTURED
1-1,SHIBAURA 1-CHOME,MINATO-KU.
TOKYO 105-8001,JAPAN
3
Introduction
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS GIVEN IN THIS
OWNER’S MANUAL AND THOSE MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR
FUTURE REFERENCE.
This set has been designed and manufactured to assure personal safety. Improper use can result in electric
shock or fire hazard. The safeguards incorporated in this unit will protect you if you observe the following
procedures for installation, use and servicing. This unit is fully transistorized and does not contain any parts that
can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.
1. Read owner’s manual
After unpacking this product, read the owner’s manual carefully, and follow
all the operating and other instructions.
2. Power Sources
This product should be operated only from the type of power source indicated
on the label. If you are not sure of the type of power supply to your home,
consult your product dealer or local power company. For products intended
to operate from battery power, or other sources, refer to the operating
instructions.
3. Grounding or Polarization
This product may be equipped with a polarized alternating current line plug
(a plug having one blade wider than the other). This plug will fit into the power
outlet only one way. This is a safety feature. If you are unable to insert the
plug fully into the outlet, try reversing the plug. If the plug should still fail to fit,
contact your electrician to replace your obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
4. Ventilation
Slots and openings in the cabinet are provided for ventilation and to ensure
reliable operation of the product and to protect it from overheating, and these
openings must not be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug or other similar surface.
This product should not be placed in a built-in installation such as a bookcase
or rack unless proper ventilation is provided or the manufacturer’s instructions
have been adhered to.
5. Heat
The product should be situated away from heat sources such as radiators,
heat registers, stoves, or other products (including amplifiers) that produce
heat.
4
6. Water and Moisture
Do not use this product near water - for example, near a bath tub, wash bowl,
kitchen sink, or laundry tub; in a wet basement; or near a swimming pool and
the like.
Introduction
7. Cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
8. Power-Cord Protection
Power-supply cords should be routed so that they are not likely to be walked
on or pinched by items placed upon or against them, paying particular attention
to cords at plugs, convenience receptacles, and the point where they exit
from the product.
9. Overloading
Do not overload wall outlets; extension cords, or integral convenience
receptacles as this can result in a risk of fire or electric shock.
10. Lightning
For added protection for this product during storm, or when it is left unattended
and unused for long periods of time, unplug it from the wall outlet. This will
prevent damage to the product due to lightning and power-line surges.
11. Object and Liquid Entry
Never insert objects of any kind into this product through openings as they
may touch dangerous voltage points or short-out parts that could result in a
fire or electric shock. Never spill liquid of any kind on the product.
12. Attachments
Do not use attachments not recommended by the product manufacturer as they may cause hazards.
5
Introduction
IMPORTANT SAFETY INSTRUCTIONS
13. Accessories
Do not place this product on an unstable cart, stand, tripod, bracket, or table.
The product may fall, causing serious injury to a child or adult, and serious
damage to the product. Use only with a cart, stand, tripod, bracket, or table
recommended by the manufacturer, or sold with the product. Any mounting
of the product should follow the manufacturer’s instructions, and should use
a mounting accessory recommended by the manufacturer.
A product and cart combination should be moved with care. Quick stops,
excessive force, and uneven surfaces may cause the product and cart
combination to overturn.
S3125A
14. Disc Tray
Keep your fingers well clear of the disc tray as it is closing. Neglecting to do
so may cause serious personal injury.
15. Burden
Do not place a heavy object on or step on the product. The object may fall,
causing serious personal injury and serious damage to the product.
16. Headphones
When you use headphones, keep the volume at a moderate level. If you use
the headphones continuously with high volume sound, it may cause hearing
damage.
17. Disc
Do not use a cracked, deformed, or repaired disc. These discs are easily
broken and may cause serious personal injury and product malfunction.
18. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following
conditions:
a) When the power-supply cord or plug is damaged.
b) If liquid has been spilled, or objects have fallen into the product.
c) If the product has been exposed to rain or water.
d) If the product does not operate normally by following the operating instructions. Adjust only those
controls that are covered by the operating instructions as an improper adjustment of other controls may
result in damage and will often require extensive work by a qualified technician to restore the product to
its normal operation.
e) If the product has been dropped or damaged in any way.
f) When the product exhibits a distinct change in performance - this indicates a need for service.
6
19. Servicing
Do not attempt to service this product yourself as opening or removing covers
may expose you to dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
Introduction
20. Replacement Parts
When replacement parts are required, be sure the service technician has used replacement parts specified
by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may
result in fire, electric shock, or other hazards.
21. Safety Check
Upon completion of any service or repairs to this product, ask the service
technician to perform safety checks to determine that the product is in proper
operating condition.
7
Introduction
Precautions
Notes on handling
When shipping the DVD video player, the original
shipping carton and packing materials come in handy.
For maximum protection, repack the unit as it was
originally packed at the factory.
Do not use volatile liquids, such as insect spray, near
the DVD video player. Do not leave rubber or plastic
products in contact with the DVD video player for a
long time. They will leave marks on the finish.
The top and rear panels of the DVD video player may
become warm after a long period of use. This is not a
malfunction.
When the DVD video player is not in use, be sure to
remove the disc and turn off the power.
If you do not use the DVD video player for a long
period, the unit may not function properly in the
future. Turn on and use the DVD video player
occasionally.
Notes on locating
Place the DVD video player on a level surface. Do not
use it on a shaky or unstable surface such as a
wobbling table or inclined stand. The loaded disc may
come off the proper position and cause damage to
the DVD video player.
When you place this DVD video player near a TV,
radio, or VCR, the playback picture may become poor
and the sound may be distorted. In this case, place
the DVD video player away from the TV, radio, or
VCR.
Notes on moisture condensation
Moisture condensation damages the DVD video
player. Please read the following carefully.
Moisture condensation occurs, for example, when you
pour a cold drink into a glass on a warm day. Drops of
water form on the outside of the glass. In the same way,
moisture may condense on the optical pick-up lens
inside this unit, one of the most crucial internal parts of
the DVD video player.
le of mo
Examp ensat isture
ion!
cond
Optical pick-up
lens
Moisture condensation occurs during the
following cases.
When you bring the DVD video player directly from a
cold place to a warm place.
When you use the DVD video player in a room where
you just turned on the heater, or a place where the
cold wind from the air conditioner directly hits the unit.
In summer, when you use the DVD video player in a
hot and humid place just after you move the unit from
an air conditioned room.
When you use the DVD video player in a humid place.
It’s too
warm!
Notes on cleaning
Use a soft, dry cloth for cleaning.
For stubborn dirt, soak the cloth in a weak detergent
solution, wring well and wipe. Use a dry cloth to wipe
it dry.
Do not use any type of solvent, such as thinner and
benzine, as they may damage the surface of the DVD
video player.
If you use a chemical saturated cloth to clean the unit,
follow that product’s instructions.
To obtain a clear picture
The DVD video player is a high technology, precision
device. If the optical pick-up lens and disc drive parts
are dirty or worn down, the picture quality becomes
poor. To obtain a clear picture, we recommend regular
inspection and maintenance (cleaning or parts
replacement) every 1,000 hours of use depending on
the operating environment. For details, contact your
nearest dealer.
8
Do not use the DVD video player when moisture
condensation may occur.
If you use the DVD video player in such a situation, it
may damage discs and internal parts. Remove the
disc, connect the power cord of the DVD video player
to the wall outlet, turn on the DVD video player, and
leave it for two or three hours. After two or three
hours, the DVD video player will have warmed up and
evaporated any moisture. Keep the DVD video player
connected to the wall outlet and moisture
condensation will seldom occur.
Wa
it!
Wall outlet
Notes on Discs
Structure of disc contents
Do not touch the playback side of the disc.
Introduction
On handling discs
Normally, DVD video discs are divided into titles, and the
titles are sub-divided into chapters. VIDEO CDs/audio
CDs are divided into tracks.
DVD video disc
DVD video disc
Title 1
Chapter 1
Title 2
Chapter 2
Chapter 1
Chapter 2
Chapter 3
Playback side
Do not attach paper or tape to discs.
VIDEO CD/Audio CD
VIDEO CD/Audio CD
Track 1
Track 2
Track 3
Track 4
Track 5
On cleaning discs
Fingerprints and dust on the disc cause picture and
sound deterioration. Wipe the disc from the center
outwards with a soft cloth. Always keep the disc
clean.
Each title, chapter or track is assigned a number, which
is called “title number”, “chapter number” or “track
number” respectively.
There may be discs that do not have these numbers.
Notes on copyright
If you cannot wipe off the dust with a soft cloth, wipe
the disc lightly with a slightly moistened soft cloth and
finish with a dry cloth.
Do not use any type of solvent such as thinner,
benzine, commercially available cleaners or antistatic
spray for vinyl LPs. It may damage the disc.
On storing discs
Do not store discs in a place subject to direct sunlight
or near heat sources.
Do not store discs in places subject to moisture and
dust such as a bathroom or near a humidifier.
Store discs vertically in a case. Stacking or placing
objects on discs outside of their case may cause
warping.
It is forbidden by law to copy, broadcast, show,
broadcast on cable, play in public, and rent copyrighted
material without permission.
DVD video discs are copy protected, and any recordings
made from these discs will be distorted.
This product incorporates copyright protection
technology that is protected by method claims of certain
U.S. patents and other intellectual property rights owned
by Macrovision Corporation and other rights owners.
Use of this copyright protection technology must be
authorized by Macrovision Corporation, and is intended
for home and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.
9
Introduction
Notes on Discs (continued)
About this owner’s manual
This owner’s manual explains the basic instructions of
this DVD video player. Some DVD video discs are
produced in a manner that allows specific or limited
operation during playback. As such, the DVD video
player may not respond to all operating commands. This
is not a defect in the DVD video player. Refer to
instruction notes of discs.
“ ” may appear on the TV screen during operation.
A “ ” means that the operation is not permitted by the
DVD video player or the disc.
Playable discs
This DVD video player can play the following discs.
Disc Mark
Contents
Disc
Size
Maximum
playback time
Approx. 4 hours
(single sided disc)
12 cm
Audio
+
video
(moving
pictures)
DVD
video
discs
Approx. 8 hours
(double sided disc)
Approx. 80 minutes
(single sided disc)
8 cm
Notes on region numbers
The region number of this DVD video player is 1. If
region numbers, which stand for their playable area, are
printed on your DVD video disc and you do not find 1
or ALL , disc playback will not be allowed by the player.
(In this case, the DVD video player will display a
message on-screen.)
Approx. 160 minutes
(double sided disc)
VIDEO
CDs
DIGITAL VIDEO
Audio
+
video
(moving
pictures)
12 cm
Approx. 74 minutes
8 cm
Approx. 20 minutes
12 cm
Approx. 74 minutes
8 cm
(CD
single)
Approx. 20 minutes
On VIDEO CDs
This DVD video player supports VIDEO CDs equipped
with the PBC (Version 2.0) function. (PBC is the
abbreviation of Playback Control.) You can enjoy two
playback variations depending on types of discs.
• VIDEO CD not equipped with PBC function
(Version 1.1)
Sound and movie can be played on this DVD video
player in the same way as an audio CD.
• VIDEO CD equipped with PBC function
(Version 2.0)
In addition to operation of a VIDEO CD not equipped
with the PBC function, you can enjoy playback of
interactive software with search function by using the
menu displayed on the TV screen (Menu Playback).
Some of the functions described in this owner’s
manual may not work with some discs.
10
Audio
CDs
Audio
The following discs are also available.
CD-R
CD-RW
CD-R/RW discs recorded by CD-DA method can be
played. Some CD-R/RW discs may be incompatible.
• You cannot play discs other than those listed above.
• You cannot play discs of DVD-RAM, DVD-RW, etc.,
even if they may be labeled marks listed above.
• This DVD video player uses the NTSC color system,
and cannot play DVD video discs recorded in any
other color system (PAL, SECAM, etc.).
Table of Contents
SAFETY PRECAUTIONS .......................... 2
IMPORTANT SAFETY INSTRUCTIONS ... 4
Precautions ............................................... 8
Notes on Discs .......................................... 9
Notes on region numbers ............................... 10
Table of Contents ................................... 11
Identification of Controls ....................... 12
Front panel ..................................................... 12
Rear panel ...................................................... 12
DVD display .................................................... 13
Remote control ............................................... 14
Loading batteries ............................................ 15
Operating with the remote control .................. 15
Connections
Advanced playback
Accessing a Specific Location Directly .. 34
Entering the time of the desired location ........ 34
Playing Repeatedly ................................. 35
Repeating a title, chapter, or track .................. 35
Repeating a specific segment ........................ 35
Playing in a Favorite Order .................... 36
Setting titles, chapters, or tracks in a favorite
order ............................................................. 36
Playing in Random Order ...................... 37
Playing titles, chapters or tracks in random
order ............................................................. 37
Zooming a Picture .................................. 38
Zooming a picture ........................................... 38
Selecting DNR Picture Enhancement ... 39
Selecting DNR picture enhancement ............. 39
Connecting to a TV ................................. 18
Selecting the Camera Angle .................. 40
Connecting to a TV ......................................... 18
Connecting to an audio system and TV
equipped with component video inputs ........ 19
Changing the camera angle ........................... 40
Selecting Subtitles ................................. 41
Connecting to Optional Equipment ...... 20
Selecting a Language ............................. 42
Connecting to an amplifier equipped with a
Dolby Digital decoder ................................... 21
Connecting to an amplifier equipped with
Dolby Pro Logic Surround ............................ 21
Connecting to an amplifier equipped with a
DTS decoder ................................................ 22
Connecting to an amplifier equipped with an
MPEG2 audio decoder ................................. 22
Connecting to an amplifier equipped with
5.1ch audio inputs ........................................ 23
Connecting to an amplifier equipped with a
digital audio input ......................................... 23
Selecting a playback audio setting ................. 42
Basic playback
Playing a Disc ......................................... 26
Basic playback ................................................ 26
Playing in fast reverse or
fast forward directions .................................. 28
Playing frame by frame ................................... 28
Playing in slow-motion .................................... 29
Resuming playback from the same location ... 29
Locating a Specific Title, Chapter, or
Track ........................................................ 30
Locating a title using the top menu ................. 30
Locating a title by entering the title number .... 30
Locating a specific chapter or track directly .... 31
Locating a specific chapter or track ................ 31
Introduction
Introduction
Selecting a subtitle language ......................... 41
Quick control
Using the Graphic Remote Control
- V-REMOTE - .......................................... 46
Selecting the Playback Function
- QUICK - .................................................. 47
Accessing Features
- NAVI - ..................................................... 48
Function setup
Customizing the Function Settings ...... 54
Setting procedure ........................................... 54
Setting details ................................................. 56
Table of Languages ................................ 65
Operating a TV with the Remote
Control ..................................................... 66
Others
Before Calling Service Personnel ......... 70
Specifications ......................................... 71
LIMITED WARRANTY DVD VIDEO
PLAYER ................................................... 72
11
Introduction
Identification of Controls
See the page in
for details.
Front panel
TOP MENU button 30
MENU button
RETURN button 54
OPEN/CLOSE 1/2 buttons 26
Cursor control 54
POWER indicator 26
Disc tray 26
PLAY button 26
OPEN/CLOSE
TOP MENU
PLAY
1
DISC-1
MENU
ENTER
OPEN/CLOSE
DISC-2
2
RETURN
STOP
POWER
DISC SELECT
SKIP
PAUSE
PAUSE button 27
DVD display 13
STOP button 27
DISC-1/2 indicators 26
SKIP buttons 31
DISC SELECT button 26
POWER button 26
Rear panel
ColorStream® (Component video)
VIDEO OUT jacks (Y/PB/PR) 19
5.1CH SURROUND AUDIO OUT jacks 23
2CH AUDIO OUT jacks 18 19
BITSTREAM/PCM COAXIAL
AUDIO OUT jack 21 22 23
VIDEO OUT jack 18
AC inlet
AUDIO OUT
VIDEO OUT
5.1CH SURROUND
2CH
BITSTREAM/PCM
Y
AC IN
CENTER
PB
VIDEO
L
PR
S
R
SUBWOOFER SURROUND FRONT
S VIDEO OUT jack 18
COAXIAL
OPTICAL
BITSTREAM/PCM OPTICAL
AUDIO OUT jack 21 22 23
When connecting the optical digital cable, remove
the cap and fit the connector into the jack firmly.
When not using the jack, keep the cap inserted
to protect it from dust intrusion.
12
Power cord
Off
Dimmed
Normal
FL DIMMER
Introduction
Repeated pressing of the FL DIMMER button on
the remote control changes the brightness of the
display.
DVD display
Total playing time/remaining time/
elapsed time indicators
Chapter/track number indicator
Title number indicator
Memory playback indicator
Disc number indicator
Random playback indicator
HDCD indicator
HDCD
DISC
TITLE GROUP
CHP
TRK
TOTAL REMAIN
MEMORY
RANDOM A-B
DVD-AUDIO
SVCDVD
VIDEO CD/CD indicator
Multifunctional indicator (indicates operating
status or messages, etc.)
DVD indicator
Angle icon indicator
Play mode indicator
Repeat playback indicator
The indicators vary depending on the kinds of discs you play.
DVD video disc
VIDEO CD
• During playback:
• During playback:
Example
HDCD
DISC
Audio CD
• During playback:
Example
TITLE GROUP
CHP
TRK
TOTAL REMAIN
MEMORY
RANDOM A-B
DVD-AUDIO
SVCDVD
Playing chapter 3
of title 2
HDCD
DISC
Example
TITLE GROUP
CHP
TRK
TOTAL REMAIN
MEMORY
RANDOM A-B
DVD-AUDIO
SVCDVD
Elapsed time
of the current
title
• Some discs may not display
chapter numbers.
• A time indication not accompanied
with a chapter number shows
elapsed time of a segment within
the current title.
Playing track 6
HDCD
DISC
TITLE GROUP
CHP
TRK
TOTAL REMAIN
MEMORY
RANDOM A-B
DVD-AUDIO
SVCDVD
Elapsed time
of the current
track
Playing track 6
Elapsed time
of the current
track
Some discs may not display track
numbers or elapsed time.
13
Introduction
Identification of Controls (continued)
The instructions in this manual describe the functions on the remote control. See the page in
for details.
Remote control
POWER button 26
DISC SELECT button 26
POWER
DISC SELECT
NAVI button 48
QUICK button 47
QUICK
SETUP
NAVI
ANGLE
SUBTITLE
AUDIO
ANGLE button 40
TOP MENU button 30
T
V-REMOTE button 46
M
OP
U
EN
V-REMOTE
ME
NU
SETUP button 54
AUDIO button 42
SUBTITLE button 41
MENU button*
Cursor control/ENTER button 54
• Cursor control – to move the cursor
Push toward the direction
you want.
• ENTER button – to enter your
selection
Press the center vertically.
ENTER
Jog control 27 28
CLEAR
RETURN
RETURN button 54
SLOW
PAUSE/STEP
SKIP
STOP
PLAY
SKIP buttons 31
CLEAR button 31
PLAY button 26
ZOOM
SLOW buttons 29
STOP button 27
PAUSE/STEP button 27
ZOOM buttons 38
COLOR STREAM
SELECTOR
DNR
DNR button 39
1
FL DIMMER
COLOR STREAM SELECTOR
button 19
Number buttons 30
3
FL DIMMER button 13
4
SEARCH
1
2
3
T
4
5
6
+10
7
8
RANDOM MEMORY
9
0
REPEAT
A-B RPT
RANDOM button 37
MEMORY button 36
T button 30
A-B RPT button 35
REPEAT button 35
Lift to open the cover.
TV
POWER TV/VIDEO
CH
VOL
TV/VIDEO button 66
POWER button 66
VOL buttons 66
CH buttons 66
When closed
14
* MENU button
Use the MENU button to display the
menu included on many DVD video
discs. To operate a menu, follow the
instructions in “Locating a title using
the top menu.” 30
1
Open the cover.
Operating with the remote control
Point the remote control at the remote
sensor and press the buttons.
30°
2
Insert batteries (AAA size).
Introduction
Loading batteries
30°
Within about 7 m (23 feet)
ENTER
Distance: About 7 m (23 feet) from the front of the
remote sensor
Angle:
About 30° in each direction of the front of
the remote sensor
Make sure to match the + and – on the batteries
to the marks inside the battery compartment.
3
Close the cover.
Notes on batteries
Improper use of batteries may cause battery leakage and
corrosion. To operate the remote control correctly, follow the
instructions below.
• Do not insert batteries into the remote control in the wrong
direction.
• Do not charge, heat, open, or short-circuit the batteries.
Do not throw batteries into a fire.
• Do not leave dead or exhausted batteries in the remote
control.
• Do not use different types of batteries together, or mix old
and new batteries.
• If you do not use the remote control for a long period of
time, remove the batteries to avoid possible damage from
battery corrosion.
• If the remote control does not function correctly or if the
operating range becomes reduced, replace all batteries
with new ones.
• If battery leakage occurs, wipe the battery liquid from the
battery compartment, then insert new batteries.
* Do not expose the remote sensor of the DVD video
player to a strong light source such as direct
sunlight or other illumination. If you do so, you may
not be able to operate the DVD video player via the
remote control.
Notes on the remote control
• Direct the remote control at the remote sensor of the DVD
video player.
• Do not drop or give the remote control a shock.
• Do not leave the remote control near an extremely hot or
humid place.
• Do not spill water or put anything wet on the remote
control.
• Do not open the remote control.
15
Connections
Read this chapter first to make all necessary
preparations.
Connecting to a TV
Connecting to an audio system
and TV equipped with
component video inputs
Connecting to an amplifier
equipped with a Dolby Digital
decoder
Connecting to an amplifier
equipped with Dolby Pro Logic
Surround
Connecting to an amplifier
equipped with a DTS decoder
Connecting to an amplifier
equipped with an MPEG2 audio
decoder
Connecting to an amplifier
equipped with 5.1ch audio
inputs
Connecting to an amplifier
equipped with a digital audio
input
Connections
Connecting to a TV
Connect the DVD video player to your TV.
For details of output sound, see 43 .
Connecting to a TV
Signal flow
AUDIO OUT
VIDEO OUT
5.1CH SURROUND
2CH
BITSTREAM/PCM
AC IN
Y
CENTER
PB
VIDEO
PR
S
L
R
SUBWOOFER SURROUND FRONT
To S VIDEO OUT
(yellow)
To VIDEO OUT
(red)
COAXIAL
OPTICAL
(white)
To wall outlet
To 2CH AUDIO OUT
Audio/video cable (supplied)
To audio inputs
To video input
(yellow)
S video cable (not supplied)
(red)
(white)
To S video input
If the TV has an S video input, connect the
DVD video player with an S video cable.
When using an S video cable, do not
connect the yellow video cable.
TV or monitor with
audio/video inputs
• Make the following setting.
On-screen display
Select:
“Audio Out Select”
“Analog 2ch”
Page
54
58
Notes
• Refer to the owner’s manual of the connected TV as well.
• When you connect the DVD video player to your TV, be sure to turn off the power and unplug both units from the wall outlet
before making any connections.
• If your television set has one audio input, connect the DVD video player to a Y cable adapter (not supplied) and then connect
to your TV.
• Connect the DVD video player directly to your TV. If you connect the DVD video player to a VCR, TV/VCR combination or
video selector, the playback picture may be distorted as DVD video discs are copy protected.
18
Connecting to an audio system and TV equipped with component video inputs
Connections
Signal flow
AUDIO OUT
VIDEO OUT
5.1CH SURROUND
2CH
BITSTREAM/PCM
AC IN
Y
CENTER
PB
VIDEO
PR
S
L
R
SUBWOOFER SURROUND FRONT
To Y
VIDEO
OUT
To PB
VIDEO
OUT
To PR
VIDEO
OUT
(white)
COAXIAL
OPTICAL
(red)
To wall outlet
To 2CH AUDIO OUT
To audio inputs of the amplifier
(red)
(white)
To PR video input
To PB video input
To Y video input
PROGRESSIVE outputs/inputs (ColorStream®Pro)
Some TVs or monitors are equipped with component video
inputs that are capable of reproducing a progressively
scanned video signal. Connecting to these inputs allows
you to view the highest quality pictures with less flicker.
INTERLACED outputs/inputs (ColorStream®)
Some TVs or monitors are equipped with component video
inputs. Connecting to these inputs allows you to enjoy
higher quality picture playback.
Actual labels for component video inputs may vary
depending on the TV manufacturer. (ex. Y, R-Y, B-Y or Y, CB,
CR)
In some TVs or monitors, the color levels of the playback
picture may be reduced slightly or the tint may change. In
such a case, adjust the TV or monitor for optimum
performance.
To switch the output signal (Progressive/
Interlaced)
Press COLOR STREAM SELECTOR on the remote
control.
The output signal alternates between component
progressive and component interlaced.
Audio system
TV or monitor with component video
(PROGRESSIVE) inputs
or
TV or monitor with component video
(INTERLACED) inputs
• Make the following setting.
On-screen display
Select:
“Audio Out Select”
“Analog 2ch”
Page
54
58
Notes
• Refer to the owner’s manual of the connected equipment as
well.
• When you connect the DVD video player to other equipment,
be sure to turn off the power and unplug all of the equipment
from the wall outlet before making any connections.
• If you place the DVD video player near a tuner or radio, the
radio broadcast sound might be distorted. In this case, place
the DVD video player away from the tuner and radio.
• The output sound of the DVD video player has a wide
dynamic range. Be sure to adjust the receiver’s volume to a
moderate listening level. Otherwise, the speakers may be
damaged by a sudden high volume sound.
• Turn off the amplifier before you connect or disconnect the
DVD video player’s power cord. If you leave the amplifier
power on, the speakers may be damaged.
19
Connections
Connecting to Optional Equipment
You can enjoy high quality dynamic sounds by connecting the DVD video player
to optional audio equipment.
• For connection to your TV, see “Connecting to a TV”
18 19 .
• For details of output sound, see 43 .
• This section uses the following reference marks.
: Front speaker
: Rear speaker
: Sub woofer
: Center speaker
: Signal flow
Notes
• DO NOT connect the BITSTREAM/PCM AUDIO OUT jack
of the DVD video player to the AC-3 RF input of a Dolby
Digital Receiver. This input on your A/V Receiver is
reserved for Laserdisc use only and is incompatible with
the BITSTREAM/PCM AUDIO OUT jack of the DVD video
player.
• Connect the BITSTREAM/PCM AUDIO OUT jack of the
DVD video player to the “OPTICAL” or “COAXIAL” input of
a Receiver or Processor.
• Refer to the owner’s manual of the connected equipment
as well.
• When you connect the DVD video player to other
equipment, be sure to turn off the power and unplug all of
the equipment from the wall outlet before making any
connections.
• The output sound of the DVD video player has a wide
dynamic range. Be sure to adjust the receiver’s volume to
a moderate listening level. Otherwise, the speakers may
be damaged by a sudden high volume sound.
• Turn off the amplifier before you connect or disconnect the
DVD video player’s power cord. If you leave the amplifier
power on, the speakers may be damaged.
20
Warning
• When you are connecting (via the BITSTREAM/PCM
AUDIO OUT jack) an AV decoder that does not have
Dolby Digital, Digital Theater Systems (DTS) or MPEG2
decoding function, be sure to set “Audio Out Select” to
“PCM” from the on-screen displays 54 58 . Otherwise,
high volume sound may damage your hearing as well as
the speakers.
• When playing DTS-encoded discs (DVD video discs
and audio CDs), excessive noise may be output from
the analog stereo jacks. To avoid possible damage to
the audio system, you should take proper precautions
when the 2CH AUDIO OUT jacks of the DVD video
player are connected to an amplification system. To
enjoy DTS Digital Surround™ playback, an external 5.1
channel DTS Digital Surround™ decoder system must
be connected to the BITSTREAM/PCM AUDIO OUT
jack of the DVD video player.
Connecting to an amplifier equipped with a Dolby Digital decoder
Amplifier equipped with a
Dolby Digital decoder
To OPTICAL
type digital
audio input
To COAXIAL
type digital
audio input
AUDIO OUT
VIDEO OUT
5.1CH SURROUND
2CH
Manufactured under license from Dolby
Laboratories. “Dolby”, “Pro Logic” and
the double-D symbol are trademarks of
Dolby Laboratories. Confidential
unpublished works. ©1992-1997 Dolby
Laboratories. All rights reserved.
• Use DVD video discs encoded via
the Dolby Digital recording
system.
• Make the following setting.
On-screen display
Select:
“Audio Out Select”
“Bitstream”
Page
54
58
BITSTREAM/PCM
Y
CENTER
PB
VIDEO
PR
S
Connections
Dolby Digital
Dolby Digital is the surround sound technology used in theaters showing the
latest movies, and is now available to reproduce this realistic effect in the home.
You can enjoy motion picture and live concert DVD video discs with this dynamic
realistic sound by connecting the DVD video player to a 6 channel amplifier
equipped with a Dolby Digital decoder or Dolby Digital processor. If you have a
Dolby Pro Logic Surround decoder, you will obtain the full benefit of Pro Logic
from the same DVD movies that provide full 5.1-channel Dolby Digital
soundtracks, as well as from titles with the Dolby Surround mark.
L
R
SUBWOOFER SURROUND FRONT
COAXIAL
OPTICAL
Recording system
42
D
Connect either.
75 Ω coaxial cable
Optical digital cable
Connecting to an amplifier equipped with Dolby Pro Logic Surround
Dolby Pro Logic Surround
You can enjoy the dynamic realistic sound of Dolby Pro Logic Surround by
connecting an amplifier and speaker system (right and left front speakers, a
center speaker, and one or two rear speakers).
With an amplifier equipped with Dolby Digital
Connect the equipment the same way as described in “Connecting to an
amplifier equipped with a Dolby Digital decoder.” Refer to that amplifier’s
owner’s manual and set the amplifier so you can enjoy Dolby Pro Logic
Surround sound.
With an amplifier not equipped with Dolby Digital
Connect the equipment as follows.
*
Amplifier equipped with
Dolby Pro Logic Surround
To audio input
AUDIO OUT
VIDEO OUT
5.1CH SURROUND
2CH
BITSTREAM/PCM
• Make the following setting.
On-screen display
Select:
“Audio Out Select”
“Analog 2ch”
Page
54
58
Be sure to set “Audio Out Select”
to “Analog 2ch” when you enjoy
sounds of Dolby Pro Logic
Surround using this connection.
* Connect one or two rear speakers.
The output sound from the rear speakers
will be monaural even if you connect two
rear speakers.
Y
CENTER
PB
VIDEO
L
PR
S
R
SUBWOOFER SURROUND FRONT
COAXIAL
OPTICAL
To 2CH AUDIO OUT
Audio cable
21
Connections
Connecting to Optional Equipment (Continued)
Connecting to an amplifier equipped with a DTS decoder
“DTS” and “DTS Digital Surround” are
Digital Theater Systems (DTS)
trademarks of Digital Theater Systems,
DTS is a high quality surround technology used in theaters and now available for Inc.
home use, on DVD video discs or audio CDs.
• Use DVD video discs or audio
If you have a DTS decoder or processor, you can obtain the full benefit of 5.1
CDs encoded via the DTS
channel DTS encoded sound tracks on DVD video discs or audio CDs.
recording system.
• Make the following setting.
Amplifier equipped with
a DTS decoder
To OPTICAL
type digital
audio input
To COAXIAL
type digital
audio input
On-screen display
Select:
“Audio Out Select”
“Bitstream”
Recording system
DTS
Page
AUDIO OUT
VIDEO OUT
5.1CH SURROUND
2CH
BITSTREAM/PCM
Y
CENTER
PB
VIDEO
PR
S
L
R
SUBWOOFER SURROUND FRONT
COAXIAL
OPTICAL
Connect either.
54
58
42
75 Ω coaxial cable
Optical digital cable
Connecting to an amplifier equipped with an MPEG2 audio decoder
MPEG2 sound
You can enjoy motion picture and live concert DVD video discs with dynamic
realistic sound by connecting an amplifier equipped with an MPEG2 audio
decoder or MPEG2 audio processor.
Amplifier equipped with an
MPEG2 audio decoder
To OPTICAL
type digital
audio input
To COAXIAL
type digital
audio input
On-screen display
Select:
“Audio Out Select”
“Bitstream”
Recording system
MPEG
AUDIO OUT
VIDEO OUT
5.1CH SURROUND
2CH
BITSTREAM/PCM
Y
CENTER
PB
VIDEO
L
PR
S
R
SUBWOOFER SURROUND FRONT
Connect either.
75 Ω coaxial cable
Optical digital cable
22
• Use DVD video discs encoded via
the MPEG2 recording system.
• Make the following setting.
COAXIAL
Page
54
58
OPTICAL
42
Connecting to an amplifier equipped with 5.1ch audio inputs
Amplifier equipped with
5.1ch audio inputs
• Use DVD video discs encoded via
the Dolby Digital recording
system.
• Make the following setting.
On-screen display
Select:
“Audio Out Select”
“Analog 6ch”
Recording system
D/MPEG
Page
54
58
AUDIO OUT
VIDEO OUT
5.1CH SURROUND
2CH
BITSTREAM/PCM
Y
CENTER
PB
VIDEO
L
PR
S
R
To 5.1ch audio
inputs
To 5.1CH SURROUND
AUDIO OUT
Audio cable
SUBWOOFER SURROUND FRONT
COAXIAL
OPTICAL
42
2 channel sound is output in the Dolby Pro
Logic format. To obtain the original 2
channel sound, select “Analog 2ch.”
Connecting to an amplifier equipped with a digital audio input
2 channel digital stereo
You can enjoy the dynamic sound of 2 channel digital stereo by connecting an
amplifier equipped with a digital audio input and speaker system (right and left
front speakers).
Amplifier equipped with
a digital audio input
To OPTICAL
type digital
audio input
To COAXIAL
type digital
audio input
• Make the following setting.
On-screen display
Select:
“Audio Out Select”
“PCM”
Page
54
58
AUDIO OUT
VIDEO OUT
5.1CH SURROUND
2CH
BITSTREAM/PCM
Y
CENTER
PB
VIDEO
PR
S
L
R
SUBWOOFER SURROUND FRONT
COAXIAL
OPTICAL
Connect either.
75 Ω coaxial cable
Optical digital cable
23
Connections
5.1ch surround sound
The Dolby Digital decoder equipped with this DVD video player enables you to
obtain the full benefit of 5.1 channel sound tracks when you connect the DVD
video player to an amplifier equipped with 5.1 channel audio inputs.
Basic playback
Begin your operation.
Playing a Disc
Locating a Specific Title,
Chapter, or Track
Basic playback
Playing a Disc
This section shows you the basics on how to play a disc.
CAUTION
Keep your fingers well clear of the disc tray as it is closing.
Neglecting to do so may cause serious personal injury.
3
POWER indicator
2, 4
PLAY
1
DISC-1/2 indicators
DVD
VCD
CD
DISC SELECT
PAUSE STOP
DVD display
Basic playback
Preparations
• When you want to view a disc, turn on the TV and select the video input connected to the DVD video player.
• When you want to enjoy the sound of discs from the audio system, turn on the audio system and select the input connected
to the DVD video player.
1
Press POWER.
POWER
The DVD video player turns on and
the POWER indicator on the player
illuminates.
4
Press OPEN/CLOSE (1/2) to close the
disc tray.
OPEN/CLOSE
1
OPEN/CLOSE
When the DVD video player is turned on for
the first time, a message appears. Press
ENTER, and make the proper settings before
proceeding to step 2. 64
2
Press OPEN/CLOSE (1/2).
OPEN/CLOSE
1
Press either button you want.
The disc tray opens.
OPEN/CLOSE
Playback starts.
If you insert a DVD video disc that contains a top
menu, a menu may appear. See “Locating a title
using the top menu.” 30
You may need to press the TOP MENU or MENU
button to display disc menu (depending on the
actual DVD video disc.)
• If the disc tray contains a disc you have already
played, playback will begin from the location where
you last stopped playback.
2
3
2
Press the button which you pressed
in step 2.
To load another disc, press the other
button.
Place a disc on the disc tray.
To change the disc
With the playback
side down.
Do not place more
than one disc.
• There are two different disc sizes. Place the disc in
the correct guide on the disc tray. If the disc is out
of the guide, it may damage the disc and cause the
DVD video player to malfunction.
• Do not place a disc which is unplayable in this
DVD video player.
Press DISC SELECT repeatedly to select the disc you
want.
Red (lit): The disc is on standby
DISC-1
DISC SELECT
or is being played.
Green
(lit):
Secondary
standby.
DISC-2
Off:
Playback does not
start.
To start playback in the stop mode
Press PLAY.
PLAY
Note
While playing a disc, you can insert another disc. Press the
OPEN/CLOSE (1/2) button to add, or remove a disc not being
played.
26
1
To obtain a higher quality picture
DISC SELECT
TOP MENU
MENU
Jog control
Occasionally, some picture noise not usually visible during a normal broadcast may
appear on the TV screen while playing a DVD video disc because the high
resolution pictures on these discs include a lot of information. While the amount of
noise depends on the TV you use with this DVD video player, you should generally
reduce the sharpness adjustment on your TV when viewing DVD video discs.
Cursor control/
ENTER
About
PLAY
STOP
PAUSE/STEP
DVD
VCD
CD
The
icons on the heading bar show the playable discs for the
function described under that heading.
DVD : You can use this function with DVD video discs.
VCD : You can use this function with VIDEO CDs.
CD
: You can use this function with audio CDs.
DVD
VCD
CD
About the screen saver
Press PAUSE/STEP during playback.
If you pause a picture of a DVD video disc and leave it
still for a long while, the screen saver of the DVD video
player automatically appears (when “Screen Saver” is
set to “On” 61 ). To turn off the screen saver, press the
PLAY button.
PAUSE/STEP
To resume normal playback, press
the PLAY button.
Alternatively press the jog control during normal
playback.
To resume normal playback, press
the jog control again.
• Sound is muted during still mode.
To stop playback
Press STOP.
STOP
To remove the disc
Press OPEN/CLOSE (1/2) for the disc you want to
remove.
OPEN/CLOSE
1
Remove the disc after the disc tray
opens completely.
OPEN/CLOSE
2
Automatic Power Off function
If the DVD video player is stopped, or the screen saver
is engaged for approximately 20 minutes, the DVD
video player will automatically turn itself off.
HDCD (High Definition Compatible Digital®)
HDCD® (High Definition Compatible Digital®) is a
recording system that has improved audio CD sound in
dynamic range, sound field reproducibility and vocal
acoustics.
This DVD video player is equipped with an HDCD
decoder. The HDCD indicator illuminates when playing
an HDCD-encoded audio CD.
®
, HDCD®, High Definition Compatible Digital® and
Pacific Microsonics™ are either registered trademarks or
trademarks of Pacific Microsonics, Inc. in the United States
and/or other countries. HDCD system manufactured under
license from Pacific Microsonics, Inc. This product is
covered by one or more of the following patents: United
States: 5,479,168, 5,638,074, 5,640,161, 5,808,574,
5,838,274, 5,854,600, 5,872,531 and 5,864,311. Australia
669114. Other patents pending.
Be sure to press the OPEN/CLOSE (1/2) button to
close the disc tray after you remove the disc.
Notes
• Do not move the DVD video player during playback. Doing so may damage the disc.
• Use the OPEN/CLOSE (1/2) button to open and close the disc tray. Do not push the disc tray while it is moving. Doing so
may cause the DVD video player to malfunction.
• Do not push up on the disc tray or put any objects other than discs on the disc tray. Doing so may cause the DVD video
player to malfunction.
• In many instances, a menu screen will appear after playback of a movie is completed. Prolonged display of an on-screen
menu may damage your television set, permanently etching that image onto its screen. To avoid this, be sure to press the
STOP button on your remote control once the movie is completed.
27
Basic playback
To pause playback (still mode)
Basic playback
Playing a Disc (continued)
You can play discs at various speeds, and resume playback from the location
where you stopped playback.
Jog control
SLOW
PLAY
STOP
PAUSE/STEP
DVD
VCD
CD
Playing in fast reverse or fast forward directions
During normal playback, move the jog
control toward
or .
To resume normal playback
Press PLAY or press the jog control.
PLAY
: Fast reverse playback
: Fast forward playback
Each time you move the jog control
up or down, the playback speed
changes.
DVD
VCD
Notes
• The DVD video player mutes sound and omits subtitles
during reverse and forward scan of DVD video discs.
However, the DVD video player plays sound during fast
forward or fast reverse play of audio CDs.
• The playback speed may differ depending on the disc.
Playing frame by frame
Press PAUSE/STEP during still playback.
PAUSE/STEP
Each time you press the PAUSE/
STEP button, the picture advances
one frame.
To resume normal playback
Press PLAY.
PLAY
Note
The sound is muted during frame by frame playback.
28
DVD
VCD
Playing in slow-motion
SLOW
Each time you press the SLOW
button, the slow-motion speed
changes.
SLOW
If you press the SLOW
button
during playback, you can view the
picture in reverse slow-motion. (Only
when using a DVD video disc.)
To resume normal playback
Basic playback
Press SLOW during playback.
Press PLAY.
PLAY
Notes
• The sound is muted during slow-motion playback.
• The playback speed may differ depending on the disc.
Each time you press the SLOW
button, the slow-motion speed
changes.
DVD
VCD
CD
1
2
Resuming playback from the same location
Press STOP at the location where you
want to interrupt playback.
STOP
The DVD video player memorizes
the location where playback is
stopped.
Press PLAY.
PLAY
The DVD video player resumes
playback from the location where
you stopped playback.
To start playback from the beginning regardless
of the location where you stopped playback
1 Press STOP twice.
STOP
The DVD video player’s memory is
cleared.
2 Press PLAY.
PLAY
DVD
Playback starts from the
beginning of the current title.
VCD
CD
Playback starts from the
beginning of the disc.
• If you want to return to the beginning of a DVD video
disc, open and close the disc tray once with the
OPEN/CLOSE (1/2) button for the disc you want to
play before pressing the PLAY button.
Notes
• The DVD video player’s memory is also cleared when:
– you unplug the DVD video player from the wall outlet after
you stop playback.
– you change the parental lock setting 62 or select a disc
menu language 60 .
– you open the disc tray for a disc which is played.
– you switch the discs by pressing the DISC SELECT button.
• There may be a difference in the location where playback
resumes depending on the disc.
• Settings you changed using the on-screen displays while the
DVD video player keeps a location in the memory may
function only after the memory is cleared.
29
Basic playback
Locating a Specific Title, Chapter, or Track
Normally, DVD video discs are divided into titles, and the titles are sub-divided into chapters. VIDEO CDs and audio CDs
are divided into tracks. You can quickly locate any specific title, chapter, or track.
DVD video disc
Title 1
Chapter 1 Chapter 2
DVD
M
OP
U
EN
The top menu appears on the TV
screen.
1
TITLE 1
TITLE 2
TITLE 3
TITLE 4
Select the title you want moving the
cursor control.
ENTER
DVD
If the titles in the top menu are
assigned a number, you can directly
locate a specific title by pressing its
designated number with the number
buttons.
Press T.
SEARCH
T
Make sure that the space next to
“Title” is highlighted.
(You can shift the highlight moving
the cursor control ( / ).)
To select title 12
30
1
Press the corresponding number
buttons for the title you want.
e.g. To select title 2
3
Track 1
Track 2
Track 3
Track 4
Track 5
3
Press ENTER.
ENTER
Playback starts from chapter 1 of the
selected title.
Notes
• The instructions above describe basic procedures which
may vary depending on the contents of the DVD video disc.
If different instructions appear on the TV screen, follow those
instructions.
• If you display the top menu during playback and press the
TOP MENU button again without selecting any title, the DVD
video player may resume playback from the point where you
first pressed the TOP MENU button (depending on the
actual DVD video disc.)
• This method of locating a title is available only on a disc that
contains a top menu.
• Instruction notes of discs may refer to the button that
displays the top menu as TITLE button.
Locating a title by entering the title number
Title : 1
Chapter:
2
VIDEO CD/Audio CD
Chapter 3
Press TOP MENU.
e.g.
2
Title 2
Chapter 2
Locating a title using the top menu
T
1
Chapter 1
2
1
2
Press PLAY.
PLAY
Playback starts from chapter 1 of the
selected title.
Notes
• Pressing the CLEAR button resets the title and chapter
numbers. To clear the “Title” and “Chapter” display, press
the T button several times.
• This method of locating a title is available only on a disc that
contains title numbers.
TOP MENU
Cursor control/
ENTER
SKIP
PLAY
CLEAR
T
Number buttons
DVD
VCD
CD
Press T.
Skip steps 1 and 2 if you are using a VIDEO CD/
audio CD.
SEARCH
Title : 1
Chapter:
T
2
3
Press PLAY.
PLAY
Playback starts from the selected
chapter or track.
1
Move the cursor control ( ) to highlight
the space next to “Chapter.”
Title : 1
Chapter:
ENTER
4
Basic playback
1
Locating a specific chapter or track directly
1
To select a title and chapter number at the same
time
Perform step 1, and enter a title number you want in the
space next to “Title” using the number buttons, then
perform steps 2 to 4.
Note
Pressing the CLEAR button resets the title and chapter
numbers. To clear the “Title” and “Chapter” display, press the
T button several times.
Press the corresponding number
buttons for the chapter or track you
want.
You can use the +10 button to select numbers
from 10 through 99.
e.g. To select chapter or track 25
2
or +10
DVD
VCD
CD
5
+10
5
Locating a specific chapter or track
Press SKIP
or
repeatedly to display
the chapter or track number you want.
Playback starts from the selected chapter or track.
SKIP
SKIP
To locate succeeding chapters or tracks
Playback starts from the beginning of the
current chapter or track.
When you press twice, playback starts
from the beginning of the preceding
chapter or track.
Notes
• Some titles may not display chapter numbers.
• When you set “Title Stop” to “Off” 63 , you can access
chapters in another title. If you go back to the preceding title
button, the DVD video player
by pressing the SKIP
locates the first chapter of the title. When “Title Stop” is set
to “On,” you can access chapters only within the current title.
or
button on the front
• If you press and hold the SKIP
panel during playback, the DVD video player performs fast
reverse or fast forward playback. You can vary the speed by
pressing the button further.
To locate chapters or tracks during fast reverse or fast
forward playback, first press the PLAY button to resume
or
button.
normal playback, then use the SKIP
31
Advanced playback
Customizing the performance of your DVD video player.
Accessing a Specific Location
Directly
Playing Repeatedly
Playing in a Favorite Order
Playing in Random Order
Zooming a Picture
Selecting DNR Picture
Enhancement
Selecting the Camera Angle
Selecting Subtitles
Selecting a Language
Advanced playback
Accessing a Specific Location Directly
You can access a specific location by entering its corresponding time (hours,
minutes, seconds).
3
1
2
DVD
VCD
CD
1
Entering the time of the desired location
Press T twice.
You may have to press further
depending on the disc. Press the
button repeatedly until the following
display appears.
SEARCH
T
Time
2
-:- - :- -
Press the number buttons to enter the
time.
e.g.
1
3
34
2
5
3
0
Time
1 : 25 : 30
Press PLAY.
PLAY
Playback starts from the desired
location.
Notes
• Some discs may not respond to this process.
• Some scenes may not be located precisely as you
specified.
• This method for accessing specific locations is available
only within the current title of the DVD video disc or within
the current track of the VIDEO CD/audio CD.
Playing Repeatedly
You can play a specific title, chapter, track, or segment repeatedly.
CLEAR
PLAY
REPEAT
A-B RPT
DVD
VCD
CD
1
Repeating a title, chapter, or track
Press REPEAT.
REPEAT
Each time you press the REPEAT
button, the repeat mode changes as
follows.
2
Press PLAY.
PLAY
DVD
DVD
VCD
CD
1
Repeats the current
chapter.
DVD
Title Repeat
VCD
CD
Track Repeat
DVD
VCD
CD
Disc Repeat
Repeats the current
disc.
DVD
VCD
CD
All Repeat
Repeats all the discs.
Repeat Off
Resumes normal
playback.
Repeats the current
title.
Repeats the current
track.
To resume normal playback
Press CLEAR.
CLEAR
Notes
• Some discs may not permit repeat operation.
• When using a DVD video disc, “All Repeat” may be canceled
when the DVD video player switches the discs.
Repeating a specific segment
Press A-B RPT at the beginning of the
segment (point A) you want to play
repeatedly.
A-B RPT
2
Chapter Repeat
Advanced playback
Chapter Repeat
The DVD video player starts repeat
playback.
Press the PLAY button within about
5 seconds after you press the
REPEAT button.
Press CLEAR.
CLEAR
A–
Press A-B RPT again at the end of the
segment (point B).
A-B RPT
To resume normal playback
The DVD video player automatically
returns to point A and starts repeat
playback of the selected segment
(A-B).
Notes
• Some discs may not permit A-B repeat operation.
• You cannot set the A-B repeat function for a segment that
includes multiple camera angles 40 .
• You can specify a segment only within the current title or
track.
• There may be a slight difference between point A and the
location where playback actually resumes depending on the
disc.
A–B
35
Advanced playback
Playing in a Favorite Order
You can combine your favorite titles, chapters, or tracks and play them in the
order you determine. You can program up to 30 selections into the memory.
(Memory playback)
Title: 2
Chapter: 25
Title: 2
Chapter: 12
Cursor contro/
ENTER
CLEAR
3
Title: 1
Chapter: 1
2
1
DVD
VCD
CD
1
Setting titles, chapters, or tracks in a favorite order
Insert a disc and press MEMORY during
stop.
MEMORY
The following display appears.
D: Disc number
T: Title number
CT: Chapter number
or track number
2
1
2
3
4
5
6
7
Memory List
D : - T : - - CT : - D : - T : - - CT : - D : - T : - - CT : - D : - T : - - CT : - D : - T : - - CT : - D : - T : - - CT : - D : - T : - - CT : - -
Select the items in the order you want
by pressing the number buttons, then
ENTER for each item.
Each time you move the cursor control ( / ), the
spaces of “D”, “T” and “CT” are highlighted in turn.
Highlight where you want to enter, then press the
corresponding number buttons.
To select tracks from a VIDEO CD/audio CD in
order, press the number buttons for the track,
then press the ENTER button for each selection
you want.
To select another title, chapter or track in the
same disc, you do not need to select the disc
number.
To select another chapter in the same title, you do
not need to select the title number.
3
Press PLAY while the “Memory List”
display appears on the TV screen.
PLAY
36
The DVD video player starts
memory playback.
To change the programmed selections
1 While the “Memory List” display appears on the TV
screen, move the cursor control ( / ) to highlight
the item you want to change.
2 Change the selection following the instructions in
step 2.
To cancel the programmed selections
1 While the “Memory List” display appears on the TV
screen, move the cursor control ( / ) to highlight
the item you want to cancel.
2 Press CLEAR.
To resume normal playback from memory
playback
Press CLEAR.
CLEAR
The memory playback indicator
disappears.
To program during playback
If you press the MEMORY button during playback, a
programming display appears.
Follow steps 2 and 3.
Notes
• Some discs may not permit memory playback operation.
• If you press the REPEAT button during memory playback,
the DVD video player repeats the current memory playback.
• If you press the MEMORY or RETURN button while the
“Memory List” display appears on the TV screen, the
“Memory List” display disappears.
• The programmed selections will be cleared when you turn off
the DVD video player.
• When using a DVD video disc, the memory playback may be
canceled when the DVD video player switches discs.
Playing in Random Order
You can play titles, chapters within a title, or tracks in random order.
(Random playback)
CLEAR
Title: 1
Chapter: 3
Title: 2
Chapter: 2
2
Title: 3
Chapter: 1
1
DVD
VCD
CD
1
Playing titles, chapters or tracks in random order
To resume normal playback
Press RANDOM.
RANDOM
Press CLEAR.
Each time you press the RANDOM
button, the random playback mode
changes as follows.
DVD
Chapter Random Plays chapters within
the current title in
random order.
DVD
Title Random
VCD
CD
Track Random
DVD
VCD
CD
All Random
Plays titles or tracks
within all discs in
random order.
Random Off
Resumes normal
playback.
Notes
• Some discs may not permit random playback operation.
• You cannot use the random playback function in conjunction
with the memory playback function.
Plays titles within the
current disc in random
order.
Plays tracks within the
current disc in random
order.
If you press the RANDOM button
during playback, the DVD video
player automatically starts random
playback after finishing the current
title, chapter or track.
2
Press PLAY.
PLAY
The DVD video player starts random
playback.
Press the PLAY button within about
5 seconds after you press the
RANDOM button.
37
Advanced playback
Chapter Random
CLEAR
Advanced playback
Zooming a Picture
You can magnify areas within a picture.
Cursor control
CLEAR
ZOOM/–/+
DVD
1
Zooming a picture
Press ZOOM during normal, slow or
still playback.
ZOOM
2
To increase the magnification level.
To reduce the magnification level.
As you move the cursor control, the
zoom point shifts.
ENTER
38
Press ZOOM repeatedly so that “Zoom Off” appears.
ZOOM
Zoom playback starts.
Select the zoom point and
magnification level.
CLEAR
To resume normal playback
Pressing the CLEAR button restores
the zoom point to the center of the
picture.
Notes
• Some discs may not respond to zoom feature.
• During some scenes, the buttons may not work as
described.
• Zooming does not work on subtitles or menus included on
DVD video discs.
• During zoom playback, the cursor control cannot work on
menus included on DVD video discs. If you want to view the
menus, cancel the zoom playback.
• The magnification level varies depending on the picture size
you select. 56
Selecting DNR Picture Enhancement
You can view a picture with less video noise.
DNR
DVD
VCD
Selecting DNR picture enhancement
Press DNR during playback.
DNR
The current setting is displayed.
DNR Off
Off
DNR1
To reduce minute video
noise
DNR2
To increase the DNR1
effect
Edge Enhance
To enhance picture edges
DNR: Digital Noise Reduction
39
Advanced playback
Each time you press the DNR
button, the setting changes as
follows.
Notes
• Actual picture enhancement may vary depending on the
quality of the disc.
• While the DNR2 level can provide additional improvement in
the reduction of noise in the video signal, it may produce
undesireble picture artifacts on some discs. Should this
occur, select a more appropriate DNR level (DNR1 or off).
• Depending on the disc, some kinds of picture details may be
lost by the picture enhancement.
Advanced playback
Selecting the Camera Angle
1, 2
If the scene was recorded from multiple angles, you can easily change
the camera angle of the scene you are watching.
2
CLEAR
DVD
1
Changing the camera angle
Press ANGLE while playing a scene
recorded with multiple angles.
ANGLE
While playing a scene recorded with
multiple angles, the angle icon ( )
appears in the DVD display and on
the TV screen.
Press the ANGLE button while the
angle icon is displayed.
e.g.
Current angle number
Angle icon
Angle : 1/ 5
2
Press ANGLE or move the cursor
control ( ) while the angle number is
displayed on the TV screen.
ANGLE
Each time you press the ANGLE
button or move the cursor control
( ), the camera angle changes.
e.g.
Angle : 1/ 5
ENTER
Angle : 2/ 5
Angle : 3/ 5
: Cycles backwards
You can change the camera angle directly by
pressing the number buttons corresponding to its
angle number instead of moving the cursor control
( / ).
40
To turn off the angle number display
Press CLEAR.
CLEAR
To disable the angle icon display on the TV
From the on-screen displays, set “On-Screen Displays”
to “Off.” 61
Monitor the DVD display when you want to change the
camera angle.
Notes
• You can change the camera angle during still playback. The
camera angle changes to the new setting when you resume
normal playback.
• If you pause a picture immediately after changing a camera
angle, the resumed playback picture may not display the
new camera angle.
Selecting Subtitles
SUBTITLE
You can display subtitles on the TV screen and select a subtitle language
from those included on the DVD video disc.
Cursor control
CLEAR
Good evening!
DVD
1
Bonsoir!
¡Buenas tardes!
Selecting a subtitle language
Press SUBTITLE during playback.
SUBTITLE
The current subtitle setting is
displayed for about 3 seconds.
To turn subtitles on or off
1 Press SUBTITLE during playback.
SUBTITLE
Language
2 Move the cursor control ( / ) while the subtitle
setting is displayed on the TV screen, to select “On”
or “Off.”
The abbreviation of the language appears instead
of the language name. Refer to the list of
languages and their abbreviations. 65
Displayed for about 3 seconds.
Subtitle : ENG On
ENTER
2
Press SUBTITLE or move the cursor
control ( ) while the subtitle setting is
displayed on the TV screen.
SUBTITLE
Each time you press the SUBTITLE
button or move the cursor control
( ), the subtitle languages included
on the DVD video disc change.
Subtitles
Subtitle : ENG Off
e.g.
ENTER
Subtitle : ENG On
Good evening!
Subtitles are
not displayed.
Subtitle : FRE On
Subtitle : SPA On
Subtitle : – – – Off
Notes
• Some DVD video discs are set to display subtitles
automatically, and you cannot turn them off even if you set
the subtitle function to off.
• During some scenes, the subtitles may not appear
immediately after you select “On.”
• Some DVD video discs will allow you to make subtitle
selections and turn subtitles on or off only via the disc menu.
: Cycles backwards
To turn off the subtitle setting
display, press the CLEAR button.
Notes
• When you turn on the DVD video player or replace a disc, the player returns to the initial default setting 60 .
When you select a subtitle language which is not included on the disc, the DVD video player plays a prior language
programmed on the disc.
• During some scenes, the subtitles may not appear immediately after you change the subtitle language by moving the cursor
control ( / ).
41
Advanced playback
Subtitle : ENG On
Advanced playback
Selecting a Language
1, 2
You can select a preferred language and sound recording system from those
included on the DVD video disc.
2
CLEAR
Good morning!
DVD
1
Bonjour!
¡Buenos días!
Selecting a playback audio setting
Press AUDIO during playback.
AUDIO
The current audio setting is
displayed for about 3 seconds.
Selecting sound channels of VIDEO CDs
You can switch left and right channels by pressing the
AUDIO button repeatedly during playback.
AUDIO
Language
Recording system
Audio channel
Audio : ENG PCM 2CH
Audio Out Select : Bitstream
Output sound format
54 58
The abbreviation of the language appears instead
of the language name. Refer to the list of
languages and their abbreviations. 65
2
Press AUDIO or move the cursor
control ( ) while the audio setting is
displayed on the TV screen.
AUDIO
Each time you press the AUDIO
button or move the cursor control
( ), the audio settings included on
the DVD video disc change.
e.g.
ENTER
Audio : ENG PCM 2CH
Audio : FRE
D 2 CH
Audio : SPA PCM 2CH
: Cycles backwards
If you move the cursor control
( / ), you can select output sound
format. 58
To turn off the audio setting display, press the
CLEAR button.
42
Notes
• When you turn on the DVD video player or replace a disc,
player returns to the initial default setting 60 .
If you select a sound track which is not included on the disc,
the DVD video player plays a prior sound track programmed
on the disc.
• Some discs allow you to change audio selections only via
the disc menu. If this is the case, press the MENU button
and choose the appropriate language from the selections on
the disc menu.
Output sound conversion table (sampling frequency/quantization bit)
Audio selection from the menu 54 58 and output jacks on the rear panel
Discs
Sound recording system
“Bitstream”
BITSTREAM/PCM
jack
Bitstream
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
Bitstream
Bitstream
44.1 kHz/16 bit
44.1 kHz/16 bit
44.1 kHz/16 bit
Bitstream
“Analog 2ch”
“PCM”
BITSTREAM/PCM
jack
2CH AUDIO
OUT jacks
BITSTREAM/PCM
jack
2CH AUDIO
OUT jacks
Bitstream
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
–
–
–
Bitstream
Bitstream
44.1 kHz/16 bit
44.1 kHz/16 bit
44.1 kHz/16 bit
Bitstream
48 kHz/20 bit
48 kHz/16 bit
48 kHz/20 bit
48 kHz/24 bit
96 kHz/16 bit
96 kHz/20 bit
96 kHz/24 bit
–
48 kHz/16 bit
44.1 kHz/16 bit
44.1 kHz/16 bit
44.1 kHz/20 bit
(Noise)
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
–
48 kHz/16 bit
44.1 kHz/16 bit
44.1 kHz/16 bit
44.1 kHz/16 bit
Bitstream
48 kHz/20 bit
48 kHz/16 bit
48 kHz/20 bit
48 kHz/24 bit
48 kHz/16 bit
48 kHz/20 bit
48 kHz/24 bit
–
48 kHz/16 bit
44.1 kHz/16 bit
44.1 kHz/16 bit
44.1 kHz/20 bit
(Noise)
• HDCD sound via the 2CH AUDIO OUT jacks and the 5.1CH SURROUND AUDIO OUT jacks is output in a normal audio CD format when
“Analog 6ch” is selected.
43
Advanced playback
Dolby Digital
48 kHz/16 bit
48 kHz/20 bit
DVD
Linear 48 kHz/24 bit
PCM
video discs
96 kHz/16 bit
96 kHz/20 bit
96 kHz/24 bit
DTS
MPEG2
VIDEO CDs
MPEG1
Linear PCM 44.1 kHz/16 bit
Audio CDs
HDCD
DTS
“Analog 6ch”
BITSTREAM/PCM 5.1CH SURROUND
AUDIO OUT jacks
jack
–
48 kHz/20 bit
48 kHz/20 bit
48 kHz/16 bit 48 kHz/16 bit 48 kHz/16 bit
48 kHz/20 bit 48 kHz/16 bit 48 kHz/20 bit
48 kHz/24 bit 48 kHz/16 bit 48 kHz/20 bit
48 kHz/16 bit 48 kHz/16 bit 48 kHz/16 bit
48 kHz/20 bit 48 kHz/16 bit 48 kHz/20 bit
48 kHz/24 bit 48 kHz/16 bit 48 kHz/20 bit
–
–
Bitstream
–
48 kHz/16 bit
48 kHz/16 bit
–
44.1 kHz/16 bit
44.1 kHz/16 bit
44.1 kHz/16 bit 44.1 kHz/16 bit 44.1 kHz/16 bit
44.1 kHz/20 bit 44.1 kHz/16 bit 44.1 kHz/16 bit
Bitstream
(Noise)
(Noise)
2CH AUDIO
OUT jacks
Quick control
Simple use of a single button and the cursor control
enables you to direct your playback, without manipulating
many actual buttons.
Using the Graphic Remote
Control - V-REMOTE Selecting the Playback Function
- QUICK Accessing Features
- NAVI -
Quick control
Using the Graphic Remote Control
- V-REMOTE -
1
2
Pressing one button can display a graphics based on-screen remote control that
allows you to control playback as if you were doing it from the actual remote
control.
DVD
VCD
CD
1
Using the graphic remote control
During playback, press V-REMOTE.
V-REMOTE
The graphic remote control (Virtual
Remote) appears.
B: Move the cursor control (
DVD
/ ) to
select “Audio,” “Subtitle,” or
“Angle,” and press ENTER.
0 : 12 : 34
Title : 1
Chapt. : 2 0 : 01 : 23
Audio
Subtitle
Angle
ENTER
Navi
Speed control
Proceed to 2-A.
Stream selection
Proceed to 2-B.
ENTER
Audio:
2A
Proceed to A or B.
DVD
VCD
CD
: Move the cursor control to select
the speed control, and press
ENTER.
Move the cursor control ( / ) to select
a desired audio language, and press
ENTER.
For details, see page 42 .
Selecting the output sound format is not
possible here.
Subtitle: Move the cursor control ( / ) to select
a desired subtitle language, and press
ENTER.
For details, see page 41 .
ENTER
Angle:
Move the cursor control ( / ) to select
a desired camera angle, and press
ENTER.
For details, see page 40 .
ENTER
: Pause 27 / Frame by frame 28
: Normal playback 26
: Slow 29
: Forward skip 31
: Fast forward 28
: Reverse slow 29
: Reverse skip 31
: Fast reverse 28
Navi : Accesses the Navi menu 48
46
To turn off the Virtual Remote
Press V-REMOTE.
V-REMOTE
Note
Some discs may not permit this operation.
Selecting the Playback Function - QUICK -
1
Pressing one button can display a list of playback functions which are relevant to
your current playback mode. You can check and modify them from the list.
DVD
VCD
CD
1
2, 3, 4
Selecting the playback function
During playback, press QUICK.
QUICK
The following on-screen display
appears.
(The actual display will vary
depending on the playback status.)
4
Press ENTER.
ENTER
The on-screen display disappears
and playback will resume according
to your selection.
e.g.
Quick menu
2
For details, see the respective pages.
Move the cursor control ( / ) to select
a desired item, and press ENTER.
Memory :
Memory List :
Repeat :
Random :
Bitrate :
To program memory playback. 36
To list memory settings. 36
To select the repeat playback mode. 35
To select the random playback mode. 37
To activate/disable the bitrate display.
Text :
To activate/disable the Text display. 48
Text display:
Displays DVD-Text data or CD-Text data
if included on the disc.
(Some content on the disc may not be
displayed properly depending on the
disc.)
To change disc selection for playback.
To quit the on-screen display.
48
e.g. To change the repeat mode:
ENTER
ENTER
3
Quick
Memory
Memory List
Repeat
Random
Bit Rate
Text
Disc Select
Exit
A-B (Set A)
Chapter
Title
Disc
All
Disc Select :
Exit :
Note
Pressing the QUICK button again also exits the on-screen
display.
Move the cursor control ( / ) to
change the setting.
e.g. To select the chapter repeat
mode:
ENTER
Quick
Memory
Memory List
Repeat
Random
Bit Rate
Text
Disc Select
Exit
A-B (Set A)
Chapter
Title
Disc
All
47
Quick control
Quick
Memory
Memory List
Repeat
Random
Bit Rate
Text
Disc Select
Exit
Quick control
Accessing Features - NAVI -
1
The NAVI menu provides an icon based display from which you can easily
access key playback function.
DVD
VCD
CD
1
2, 3
NAVI menu items
3
Press NAVI.
NAVI
The NAVI menu appears.
Press ENTER.
Selection details appears.
ENTER
Feature icon
N-2-2
Angle Viewer
V-Remote
Navi
Zoom
Z
M
Capture
Title:
Chapt.:
Audio
Subtitle
Angle
Bit Rate:
Strobe Viewer
DNR
Title/Chapt.: Elapsed time and remainig time of
the current title/chapter.
Audio:
Current audio setting
Subtitle:
Current subtitle setting
Angle:
Current angle setting
Bit Rate:
Data transfer rate (Mbit/s)
Amount of picture, sound and subtitle
data in the DVD video disc
transferred per second.
The larger the value, the more data
processed, but this does not
necessarily insure better picture
quality.
Status display (playback mode, current DNR
setting, current zoom status, etc.)
Move the cursor control to select a
desired feature icon.
For details on each feature, refer to
the list on the next page.
ENTER
48
Refer to the list on the next page and
follow the instructions detailed on
subsequent pages.
Preview
Each time you press the NAVI button, the display
changes.
2
4
Notes
• The NAVI menu will disappear by pressing the NAVI button
several times.
• The number of feature icons on the display will vary
depending on the disc.
Navi menu selections
V-Remote
You can control key playback functions using the graphics based
on-screen remote control.
46
You can display all camera angles simultaneously and select your
preferred one from them.
50
You can magnify areas within a picture.
38
You can divide a desired scene into stop action frames for careful
analysis.
50
You can display thumbnail views of the first scenes of titles or
chapters and select a preferred one.
51
You can view a picture with less video noise.
51
You can sample a scene from a playback picture and transform it
into a background picture.
52
Navi
Zoom
Z
Quick control
Angle Viewer
M
Strobe Viewer
Preview
DNR
Capture
49
Quick control
Accessing Features - NAVI - (continued)
NAVI menu items
Angle Viewer
You can display all camera
angles simultaneously and
select your preferred one
from them.
You can divide a desired
scene into stop action
frames for careful analysis.
Strobe Viewer
After selecting this icon and pressing ENTER, the
following on-screen display appears:
After selecting this icon and pressing ENTER, the
following on-screen display appears:
e.g.
e.g.
1
2
3
4
5
6
7
8
9
Slow
Angle Viewer
Navi
Exit
Strobe Viewer
Normal
>>
Fast
Navi
Exit
When the scene contains 9 camera angles:
1 Move the cursor control to select.
ENTER
1-9 : To select the camera angle.
Navi: To return to the NAVI menu.
Exit : To quit the on-screen display.
2 Press ENTER.
ENTER
Note
Some discs or scenes may not permit this operation.
1 Move the cursor control to select.
ENTER
Slow: Still pictures at shorter intervals.
Normal: Still pictures at normal intervals.
Fast: Still pictures at longer intervals.
>>:
To view the next series of 6 pictures.
Navi: To return to the NAVI menu.
Exit : To quit the on-screen display.
2 Press ENTER.
ENTER
Note
Some discs or scenes may not permit this operation.
50
You can display thumbnail
views of the first scenes of
titles or chapters and
select a preferred one.
Preview
You can view a picture
with less video noise.
DNR
After selecting this icon and pressing ENTER, the
following on-screen display appears:
After selecting this icon and pressing ENTER, the
following on-screen display appears:
e.g.
e.g.
2
4
3
5
Title
Preview
DNR
DNR2
DNR1
DNR Off
Edge Enhance
6
Chapter
<<
>>
Quick control
1
Interval
Navi
Exit
1 Move the cursor control to select.
ENTER
1 - 6:
To locate the scene.
Title:
To display the first scenes of titles (1 to 6).
Chapter: To display the first scenes of chapters
(1 to 6).
Interval: To display scenes at intervals of about 10
minutes apart.
<< :
To go to the previous page.
>> :
To go to the next page.
Navi:
To return to the NAVI menu.
Exit :
To quit the on-screen display.
2 Press ENTER.
1 Move the cursor control to select.
ENTER
DNR2:
DNR1:
DNR Off:
Edge Enhance :
To increase the DNR1 effect.
To reduce minute video noise.
Off.
To sharpen picture edges.
2 Press ENTER.
ENTER
Note
For details and notes on the DNR picture enhancement,
see page 39 .
ENTER
Note
• Some discs or scenes may not permit this operation.
• Some items may not be selected depending on the
disc or scene.
• Some of the first scenes may not picked up depending
on the disc.
51
Quick control
Accessing Features - NAVI - (continued)
NAVI menu items
Capture
You can sample a scene
from a playback picture
and transform it into a
background picture.
After selecting this icon and pressing ENTER, the
following on-screen display appears:
e.g.
Capture
Storing
Navi
Exit
1 Pause playback at a scene you want to capture.
2 Move the cursor control to select.
ENTER
Storing: To sample and store the current picture
in the player memory.
Navi:
To return to the NAVI menu.
Exit :
To quit the on-screen display.
3 Press ENTER.
ENTER
The stored picture will be displayed as a
background picture when the player is in the stop
mode. It is necessary to confirm this process via
the setup menu 61 .
Notes
• You can store only one picture. Storing a new picture
will erase the old one.
• No operations are permitted in process of sampling
and storage of background picture.
52
Function Setup
You can change the default settings to customize
performance to your preference.
Customizing the Function
Settings
Table of Languages
Operating a TV with the remote
control
Function setup
Customizing the Function Settings
1, 6
You can change the default settings to customize performance to your
preference.
2, 3, 4
RETURN
DVD
VCD
CD
1
Setting procedure
Press SETUP during stop.
SETUP
The following on-screen display
appears.
3
Move the cursor control ( / ) to select
the setting you want to change, then
press ENTER.
AB C
Picture
TV Shape
Blacker than Black
Setting : Interlaced
Setting : Progressive
Progressive 4:3 Output
Progressive Conversion
2
4:3 LB
Off
1
1
Full
Auto
Move the cursor control ( / ) to select
a symbol for the setting you want to
change.
ENTER
4
Change the selection by the cursor
control ( / ) or other buttons, by
referring to the corresponding pages
56 , then press ENTER.
(See the next page.)
ENTER
ENTER
5
Repeat steps 3 and 4 to change other
settings.
6
Press SETUP.
Picture performance settings
Output sound settings
AB C
Language settings
To select another operation, go back to step 2.
SETUP
The on-screen display disappears.
To return to the previous display
Press RETURN.
RETURN
Display settings
Operational settings
Initial settings
54
Notes
• The on-screen display disappears when you press the
SETUP button.
• The SETUP button can function even during normal
playback, however some operations may be inaccessible,
and a message will appear. In this case, try again after
playback is stopped.
Setting
TV Shape
Blacker than Black
Setting: Interlaced
Details
DVD
DVD
VCD
DVD
VCD
Page
To select a picture size according to the aspect
ratio of your TV.
56
To make an adjustment of the black level on
your TV using a commercially available test disc
that contains adjustment signals.
56
To adjust the picture quality.
56
Setting: Progressive
DVD
VCD
To adjust the picture quality. (Only when
connected to a PROGRESSIVE TV.)
57
Progressive 4:3 Output
DVD
VCD
To select the video output of pictures recorded
in 4:3 format. (Only when connected to a
PROGRESSIVE TV.)
57
DVD
VCD
To select the system of output signal. (Only
when connected to a PROGRESSIVE TV.)
57
DVD
VCD
CD
To select an output sound format corresponding
to your system connection.
58
To turn on or off a function that makes faint
sounds easier to hear even if you lower the
volume during late hours playback.
59
Progressive Conversion
Audio Out Select
Dynamic Range Control
DVD
Karaoke Vocal
DVD
To turn on or off the vocal output during DVD
KARAOKE disc playback.
59
CD Attenuation
CD
To attenuate sound distortion incurred during
playback of an audio CD.
59
DVD
VCD
CD
To select a preferred language for on-screen
displays.
60
Disc Menu Language
DVD
To select a preferred language for disc menus.
60
Audio Language
DVD
To select a preferred language for the sound
track.
60
Subtitle Language
DVD
To select a preferred language for subtitles.
60
On-Screen Displays
DVD
VCD
CD
To turn on or de-activate the operational status
display on the TV screen.
61
Background
DVD
VCD
CD
To select the background color or background
picture.
61
Screen Saver
DVD
To turn the screen saver on or off.
61
Pause/Still
DVD
To select the resolution of still pictures.
(Field/Frame)
62
Parental Lock
DVD
To turn the parental lock function on or off.
62
Remote Confirmation
DVD
VCD
CD
To turn on or off the confirmation beeper
announcing when each remote command
received.
63
Title Stop
DVD
To turn on or off a feature that automatically
stops playback after a title has been viewed.
63
PBC
VCD
To use the menu screen when playing a PBCcontrollable VIDEO CD.
63
On-screen Language
TV Shape
Audio Out Select
DVD
VCD
CD
To install the initial system setting.
64
Function setup
On-Screen Language
AB C
55
Function setup
Customizing the Function Settings (continued)
Setting details
AB C
Picture
TV Shape
Blacker than Black
Setting : Interlaced
Setting : Progressive
Progressive 4:3 Output
Progressive Conversion
TV Shape
4:3 LB
Off
1
1
Full
Auto
Setting : Interlaced
DVD
VCD
You can fine adjust picture quality and store up to 3
custom picture settings in the memory of the DVD
video player.
To select a preset memory setting:
1) Move the cursor control ( / ) to select a
memory number (1 to 3), and press the ENTER
button.
DVD
AB C
4:3 Letterbox:
Select when a standard 4:3 TV is
connected.
Displays theatrical images with
masking bars above and below the
picture.
4:3 Normal:
Select when a standard 4:3 TV is
connected.
Displays pictures cropped to fill
your TV screen. Either or both
sides of the picture are cut off.
16:9 Widescreen: Select when a 16:9 wide TV is
connected.
Notes
• The displayable picture size is preset on the DVD video
disc. Therefore, the playback picture of some DVD
video discs may not conform to the picture size you
select.
• When you play DVD video discs recorded in the 4:3
picture size only, the playback picture always appears
in the 4:3 picture size regardless of the TV shape
setting.
• If you select “16:9 Widescreen” and you own a 4:3 TV
set, the DVD playback picture will be horizontally
distorted during playback. Images will appear to be
horizontally compressed. Always be sure that your TV
shape conforms to the actual TV in use.
Blacker than Black
DVD
VCD
Off: For normal use.
On: Select when you adjust the black level of your
TV using a commercially available test disc that
contains adjustment signals.
Picture
TV Shape
Blacker than Black
Setting : Interlaced
Setting : Progressive
Progressive 4:3 Output
Progressive Conversion
4:3 LB
Off
1
1
Full
Auto
1
2
3
2) Move the cursor control ( / ) to select the
element, and press the ENTER button.
AB C
Setting : Interlaced
Contrast
0
Brightness
0
Color
0
Tint
0
Sharpness
0
Black Level
NRML
Gamma
–
Y/C Time Correction 0
3) Move the cursor control ( / ) to adjust the
value, and press the ENTER button.
(-7) Lower
Contrast
Higher (+7)
(-7) Darker
Brightness
Brighter (+7)
(-7) Duller
Color
Brighter (+7)
(-7) Redder
Tint
Greener (+7)
(-7) Softer
Sharpness
Sharper (+7)
Normal
Black Level
Enhanced
(–)
Gamma*1
(+)
(-3)
Y/C Time Correction*2
(+3)
*1: Adjust when playback pictures are too dark or too
whitish.
*2: Adjust horizontal color deviations. Pictures may
shift horizontally during the adjustment.
Notes
• These adjustments are not available when connecting
to a PROGRESSIVE TV.
• The Tint adjustment is not available when connecting to
a TV via the component video jacks (Y, PB, PR).
56
Setting : Progressive
DVD
Progressive 4:3 Output
VCD
You can fine adjust picture quality and store up to 3
picture settings in the memory of the DVD video
player. (Only when connected to a PROGRESSIVE
TV.)
To select a preset memory setting:
1) Move the cursor control ( / ) to select a
memory number (1 to 3), and press the ENTER
button.
DVD
DVD VCD
VCD
Select the video output of pictures recorded in 4:3
format. (Only when connected to a PROGRESSIVE
TV.)
4:3: Displays images in 4:3 aspect ratio with
masking bars to the left and right of the picture.
Full: Displays pictures expanded horizontally to fill
the 16:9 screen.
AB C
Picture
TV Shape
Blacker than Black
Setting : Interlaced
Setting : Progressive
Progressive 4:3 Output
Progressive Conversion
4:3 LB
Off
1
1
Full
Auto
1
2
3
AB C
Setting : Progressive
Contrast
0
Brightness
0
Color
0
Tint
0
Edge Enhance Off
3) Move the cursor control ( / ) to adjust the
value, and press the ENTER button.
(-7) Lower
(0) Darker
(-7) Duller
(-7) Redder
Contrast
Higher (+7)
Brightness
Brighter (+14)
Color
Brighter (+7)
Tint
Greener (+7)
Edge Enhance
To enhance picture edges.
(Off < On < Expanded1 < Expanded2)
DVD
VCD
There are two types of source content in pictures
recorded in DVD video discs: film content (pictures
recorded from films at 24 frames per second) and
video content (video signals recorded at 30 frames
per second). Make this selection according to the
type of content being viewed.
Function setup
2) Move the cursor control ( / ) to select the
element, and press the ENTER button.
Progressive Conversion
Auto: Select this position normally.
The DVD video player automatically detects
source content, film or video, of playback
source, and converts that signal in the
progressive output format in an appropriate
method.
Video: The DVD video player filters video signal, and
converts it in the progressive output format
appropriately.
Suitable for playback of video content
pictures.
Film: The DVD video player converts film content
pictures in the progressive output format
appropriately.
Suitable for playback of film content pictures.
The progressive output feature will be most
effective under this selection.
Note
Depending on the disc, pictures may be cut off or
doubled. In this case, select “Video.”
57
Function setup
Customizing the Function Settings (continued)
Setting details
When you select “Analog 6Ch”:
AB C
Audio
Audio Out Select
Dynamic Range Control
Karaoke Vocal
CD Attenuation
Audio Out Select
DVD
VCD
Bitstream
On
Off
Off
AB C
Analog 6ch
C. S. Speaker Size
C (Center) Speaker
S (Surround) Speaker
Subwoofer
Center Channel Delay
Surround Channel Delay
Test Tone
CD
Select the output sound format corresponding to your
system connection.
For details of sound recording systems, see 43 .
Bitstream:
Make the following settings for the built-in 5.1ch
surround decoder.
Select when connected to an amplifier
equipped with a Dolby Digital, DTS,
MPEG1 or MPEG2 decoder. 21 22
The DVD video player outputs digital
audio information in the bitstream
format when you play a DVD video disc
recorded on the Dolby Digital, DTS,
MPEG1 or MPEG2 recording system.
Analog 6ch: Select when connected to an AV
amplifier equipped with 5.1ch audio
inputs. 23
This DVD video player is equipped with
a Dolby Digital and MPEG decoder.
The next screen will detail the
appropriate settings.
Large
On
On
On
0msec
5msec
1) Select an item by moving the cursor control
( / ), and press the ENTER button.
2) Make the settings (see below) by moving the
cursor control ( / / / ), and press the
ENTER button.
C.S.Speaker Size
Small: When the center speaker or surround
speakers cannot reproduce low frequency
signals below 120 Hz.
Large: When the center speaker and surround
speakers can reproduce low frequency
signals below 120 Hz.
C(Center) Speaker
Off: When center speaker is not connected.
On: When you connect center speaker.
S(Surround) Speaker
Analog 2ch: Select when connected to a TV, or
Dolby Pro Logic or stereo system via
the analog audio jacks. 18 19 21
Off: When surround speakers are not connected.
On: When you connect surround speakers.
Subwoofer
PCM:
58
Select when connected to a 2 channel
digital stereo amplifier. 23
The DVD video player outputs sounds
in the PCM 2ch format when you play a
DVD video disc recorded on the Dolby
Digital, MPEG1 or MPEG2 recording
system.
Off: When a sub woofer is not connected.
On: When you connect a sub woofer.
Adjusting the delay time:
When enjoying 5.1ch surround playback, it is ideal
to choose a listening position that is the same
distance from each speaker. By adjusting the
delay time of the center/surround speakers, you
can virtually create an ideal listening environment
(as if the center/surround speakers were at their
ideal locations respectively as below.)
Ideal location of a
center speaker
(A)
FL
FR
Dc
SW
Df
Ds
SL
SR
All speakers should
be located within a
circle with a radius
of Df.
(B)
Center Channel Delay
0msec:
1msec:
2msec:
3msec:
When Df equals Dc.
When (A) is approx. 34 cm (13 inch)
When (A) is approx. 68 cm (27 inch)
When (A) is approx. 102 cm (40 inch) . . .
*(A) = Df – Dc
Get your optimum value (0, 1, 2 . . . 5)
dividing (A) by 34.
Surround Channel Delay
0msec:
1msec:
2msec:
3msec:
When Df equals Ds.
When (B) is approx. 34 cm (13 inch)
When (B) is approx. 68 cm (27 inch)
When (B) is approx. 102 cm (40 inch) . . .
*(B) = Df – Ds
Get your optimum value (0, 1, 2 . . . 15)
dividing (B) by 34.
3) Select “Test Tone” and press the ENTER
button.
The DVD video player outputs a test signal to
each speaker when it is in stop mode. When
playing a DVD video disc, it substitutes the
current sound for the test signal.
Move the cursor control ( / ) to select the
receiving speakers, and adjust the volume of
each speaker at the same level by moving the
cursor control ( / ).
If all the volume levels cannot be equalized,
adjust them on the amplifier.
Dynamic Range Control
DVD
Off: Full dynamic range is maintained.
On: Dynamic range is reduced.
Notes
• This function works only during playback of Dolby
Digital recorded discs.
• The level of Dynamic Range Reduction may differ
depending on the DVD video disc.
Karaoke Vocal
DVD
Off: The primary vocal is not output.
On: The primary vocal is output when it is recorded
on the disc.
Notes
• The vocal output feature is used during playback of
Dolby Digital (multi-channel) recorded DVD KARAOKE
discs. This feature allows you to turn off vocal audio
tracks, or restore them for background accompaniment.
• When playing KARAOKE, connect appropriate audio
equipment such as an amplifier to the DVD video
player.
CD Attenuation
CD
HDCD enhances the output sound level of audio CD
by approximately 6 dB. As such, distortion may occur
in some connected products that are unable to
compensate for a wide range of input signal levels.
(e.g. TV, stereo receivers)
Off: For normal use.
On: Select when an audio CD sound is distorted.
Sound volume of an audio CD is lessened.
59
Function setup
Ideal location of a
surround speaker
Note
Depending on the disc, 6 channel sounds may not be
output via the 5.1 CH SURROUND AUDIO OUT jacks.
Function setup
Customizing the Function Settings (continued)
Setting details
Audio Language
AB C
AB C
Language
On-Screen Language ENG
Disc Menu Language ENG
Audio Language
ENG
Subtitle Language – – –
On-Screen Language
DVD
English:
French:
Spanish:
Others:
VCD
CD
English: To view on-screen displays in English.
Français: To view on-screen displays in French.
Español: To view on-screen displays in Spanish.
Disc Menu Language
English:
French:
Spanish
Others:
DVD
To play sound tracks in English.
To play sound tracks in French.
To play sound tracks in Spanish.
To make a further choice.
After pressing the ENTER button, follow
steps 1) - 4) below.
1) Obtain the abbreviation of the preferred
language from the list 65 .
2) Select the first character by moving the cursor
control ( / ).
3) Move the cursor control ( / ) to shift and
select the second character by moving the
cursor control ( / ).
DVD
AB C
Language
On-Screen Language ENG
Disc Menu Language ENG
Audio Language
ENG
Subtitle Language – – –
To display disc menus in English.
To display disc menus in French.
To display disc menus in Spanish.
To make a further choice.
After pressing the ENTER button, follow
steps 1) - 4) below.
1) Obtain the abbreviation of the preferred
language from the list 65 .
2) Select the first character by moving the cursor
control ( / ).
3) Move the cursor control ( / ) to shift and
select the second character by moving the
cursor control ( / ).
English
French
Spanish
Others
Code E S
4) Press the ENTER button.
Note
Some DVD video discs may be played in a different
language than you selected. A prior language may be
programmed on the disc.
AB C
Language
On-Screen Language ENG
Disc Menu Language ENG
Audio Language
ENG
Subtitle Language – – –
Subtitle Language
English
French
Spanish
Others
Code E S
4) Press the ENTER button.
Note
Some DVD video discs may not include your preselected language. In this case, the DVD video player
automatically displays disc menus consistent with the
disc’s initial language setting.
60
English:
French:
Spanish:
No Subtitle:
Others:
DVD
To display subtitles in English.
To display subtitles in French.
To display subtitles in Spanish.
To disable subtitles.
To make a further choice.
After pressing the ENTER button,
follow steps 1) - 4) below.
1) Obtain the abbreviation of the preferred
language from the list 65 .
2) Select the first character by moving the cursor
control ( / ).
AB C
3) Move the cursor control ( / ) to shift and
select the second character by moving the
cursor control ( / ).
Display
On-Screen Displays On
Background
Gray
Screen Saver
On
AB C
Language
On-Screen Language ENG
Disc Menu Language ENG
Audio Language
ENG
Subtitle Language – – –
English
French
Spanish
No Subtitle
Others
Code A A
4) Press the ENTER button.
DVD
VCD
Off: Operational modes (e.g. “Play”, “
displayed.
On: Operational modes (e.g. “Play”, “
displayed on-screen.
Background
DVD
VCD
CD
”) are not
”) are
CD
Blue:
Blue background.
Gray:
Gray background.
Capture: To use a picture you sampled and stored in
the memory using the Capture feature 52
as a background.
Jacket: To use the jacket picture included on some
discs as a background. If it is not included,
a gray background will be substituted.
Screen Saver
Function setup
Notes
• Some DVD video discs may be set to display subtitles
in a different language than you selected. A prior
subtitle language may be programmed on the disc.
• Some DVD video discs allow you to change subtitle
selections only via the disc menu. If this is the case,
press the MENU button and choose the appropriate
subtitle language from the selection on the disc menu.
On-Screen Displays
DVD
Off: The screen saver is disengaged.
On: The screen saver operates.
61
Function setup
Customizing the Function Settings (continued)
Setting details
1) Press the number buttons to create a personal
4-digit security code, then press the ENTER
button.
If you make a mistake before pressing the
ENTER button, press the CLEAR button and
enter your 4-digit security code again.
AB C
Operation
Pause/Still
Parental Lock
Remote Confirmation
Title Stop
PBC
Pause/Still
Auto
Off
On
Off
On
2) Enter the code of a country whose standards
were used to rate the DVD video disc, referring
to the list below.
DVD
Auto:
For normal use. Still and fast motion images
can be paused.
Frame: The resolution of still pictures is improved,
so that you can make a motionless picture
more clearer when you pause it.
Parental Lock
DVD
DVD video discs equipped with the parental lock
function are rated according to their content. The
contents allowed by a parental lock level and the way
a DVD video disc can be controlled may vary from
disc to disc. For example, if the disc allowed you
could edit out violent scenes unsuitable for children
and replace them with more suitable scenes, or lock
out playback of the disc altogether.
• DVD video discs may or may not respond to the
parental lock settings. This is not a defect in the DVD
video player. Make sure this function works with your
DVD video discs.
Off: The parental lock feature does not function.
After pressing the ENTER button, follow step 1)
below.
On: To activate the parental lock feature or change
the settings.
After pressing the ENTER button, follow steps
1) - 3) below.
AB C
Operation
Pause/Still
Parental Lock
Remote Confirmation
Title Stop
PBC
62
Auto
Off
On
Off
On
Off
On
Security Code – – – –
Country
AUSTRALIA
BELGIUM
CANADA
CHINA
DENMARK
FINLAND
FRANCE
GERMANY
HONG KONG
INDONESIA
ITALY
JAPAN
MALAYSIA
NETHERLANDS
NORWAY
PHILIPPINES
RUSSIAN FEDERATION
SINGAPORE
SPAIN
SWEDEN
SWITZERLAND
TAIWAN
THAILAND
UNITED KINDOM
UNITED STATES
Code
AU
BE
CA
CN
DK
FI
FR
DE
HK
ID
IT
JP
MY
NL
NO
PH
RU
SG
ES
SE
CH
TW
TH
GB
US
a) Select the first character by moving the
cursor control ( / ).
b) Move the cursor control ( / ) to shift and
select the second character by moving the
cursor control ( / ).
c) Press the ENTER button.
3) Move the cursor control ( / ) to select the
parental lock level, then press the ENTER
button.
Remote Confirmation
DVD
VCD
CD
Off: The beeper does not sound.
On: The beeper sounds with each remote operation.
AB C
Operation
Pause/Still
Parental Lock
Remote Confirmation
Title Stop
PBC
Auto
Off
On
Off
On
Title Stop
Country Code U S
Level
7
You cannot play DVD video discs rated higher than
the level you selected unless you cancel the parental
lock function.
For example, when you select level 7, discs rated
higher than level 7 are locked out and cannot be
played.
DVD
Off: The DVD video player continues after playback
of a title is completed.
On: The DVD video player stops after playback of a
title is completed.
PBC
VCD
Off: When playing a VIDEO CD without using the
menu.
On: To use the menu when playing a PBC-featured
VIDEO CD.
Function setup
The parental lock level is equivalent to the following
USA movie ratings.
Level 7: NC-17
Level 6: R
Level 4: PG 13
Level 3: PG
Level 1: G
The parental lock levels for other countries than U.S.
are included for future use. Check the appropriate
parental lock level when you buy a DVD video disc
equipped with the parental lock feature in the future.
To change the parental lock level
Follow steps 1) - 3).
To change your 4-digit security code
1) After selecting “On” or “Off,” press the STOP
button four times, then press the ENTER
button.
STOP
STOP
STOP
STOP
ENTER
The 4-digit security code is cleared.
2) Press the number buttons to create a new
4-digit security code.
3) Press the ENTER button.
63
Function setup
Customizing the Function Settings (continued)
Setting details
AB C
Initial Setup
On-Screen Language ENG
TV Shape
4:3 LB
Audio Out Select
Bitstream
Initial Setup
DVD
VCD
CD
1) Move the cursor control ( / ) to select “OnScreen Language,” and press the ENTER
button.
ENTER
ENTER
2) Select a language moving the cursor control
( / ), and press the ENTER button.
See page 60 , “On-screen Language.”
ENTER
ENTER
3) Make your selection in the same manner as
step 1) then step 2).
See page
See page
64
56
58
, “TV Shape.”
, “Audio Out Select.”
Table of Languages
Table of languages and their abbreviations
Abbreviation
–––
No alternate
language
Chinese
Dutch
English
French
German
Italian
Japanese
Korean
Malay
Spanish
Afar
Abkhazian
Afrikaans
Amharic
Arabic
Assamese
Aymara
Azerbaijani
Bashkir
Belorussian
Bulgarian
Bihari
Bislama
Bengali, Bangla
Tibetan
Breton
Catalan
Corsican
Czech
Welsh
Danish
Bhutani
Greek
Esperanto
Estonian
Basque
Persian
Finnish
Fiji
Faroese
Frisian
Irish
Scottish Gaelic
Galician
Abbreviation
GN
GU
HA
HI
HR
HU
HY
IA
IE
IK
IN
IS
IW
JI
JW
KA
KK
KL
KM
KN
KS
KU
KY
LA
LN
LO
LT
LV
MG
MI
MK
ML
MN
MO
MR
MT
MY
NA
NE
NO
OC
OM
OR
PA
PL
PS
Language
Guarani
Gujarati
Hausa
Hindi
Croatian
Hungarian
Armenian
Interlingua
Interlingue
Inupiak
Indonesian
Icelandic
Hebrew
Yiddish
Javanese
Georgian
Kazakh
Greenlandic
Cambodian
Kannada
Kashmiri
Kurdish
Kirghiz
Latin
Lingala
Laotian
Lithuanian
Latvian, Lettish
Malagasy
Maori
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Maltese
Burmese
Nauru
Nepali
Norwegian
Occitan
(Afan) Oromo
Oriya
Panjabi
Polish
Pashto, Pushto
Abbreviation
PT
QU
RM
RN
RO
RU
RW
SA
SD
SG
SH
SI
SK
SL
SM
SN
SO
SQ
SR
SS
ST
SU
SV
SW
TA
TE
TG
TH
TI
TK
TL
TN
TO
TR
TS
TT
TW
UK
UR
UZ
VI
VO
WO
XH
YO
ZU
Language
Portuguese
Quechua
Rhaeto-Romance
Kirundi
Rumanian
Russian
Kinyarwanda
Sanskrit
Sindhi
Sango
Serbo-Croatian
Singhalese
Slovak
Slovenian
Samoan
Shona
Somali
Albanian
Serbian
Siswati
Sesotho
Sundanese
Swedish
Swahili
Tamil
Telugu
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Setswana
Tongan
Turkish
Tsonga
Tatar
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapük
Wolof
Xhosa
Yoruba
Zulu
Function setup
CHI (ZH)
DUT (NL)
ENG (EN)
FRE (FR)
GER (DE)
ITA (IT)
JPN (JA)
KOR (KO)
MAY (MS)
SPA (ES)
AA
AB
AF
AM
AR
AS
AY
AZ
BA
BE
BG
BH
BI
BN
BO
BR
CA
CO
CS
CY
DA
DZ
EL
EO
ET
EU
FA
FI
FJ
FO
FY
GA
GD
GL
Language
65
Function setup
Operating a TV with the remote
control
ENTER
You can operate the basic functions of selected TVs
using the supplied remote control.
POWER
TV/VIDEO
VOL
CH
Number buttons
Operating a TV with the remote control
Preparation
Follow the instruction of “To program the remote control” to set the brand code.
Point the remote control at your TV, and
use buttons as follows.
POWER
TV/VIDEO
VOL /
CH /
To turn the power on and off.
To select a video input.
To adjust the volume.
To select a channel.
To program the remote control
1 While holding down ENTER, press the number
buttons that correspond to your TV’s brand code
referring to the list on the next page.
e.g. To Program brand code 0071.
ENTER
0
0
7
1
Hold down.
2 Release ENTER.
The DVD remote control memorizes the selected
brand code.
POWER
TV/VIDEO
VOL
CH
Close the cover to
use these buttons.
66
Notes
• The remote control is programmed at the factory to operate
TOSHIBA TVs.
• A single brand may use different codes depending on the
particular model. Enter the correct number referring to the
brand code table.
• For some brands, several brand codes are provided. Try
each of them until the remote control operates your TV.
• Some TVs may not respond to all of the functions in the
table above, or may not be operated at all with this remote
control. In this case, operate that TV with its own remote
control.
• If you replace the remote control’s batteries, remember to
reprogram the brand codes for TV.
Brand code table
Brand code
TOSHIBA
BELL & HOWELL
CARVER
CITIZEN
CURTIS MATHES
0001
0471
0201
0201
0471
0311
0201
0581
0041
0471
0941
0991
0201
0001
0481
0021
0381
0501
0501
0311
0001
0501
0471
0201
0411
0201
0201
0511
0201
0001
0511
0371
0841
0071
0301
0071
0501
0201
0931
0341
0371
0841
0631
0851
0331
EMERSON
FISHER
GE
GOLDSTAR
HALLMARK
HITACHI
INFINITY
JBL
JVC
LXI
MAGNAVOX
MARANTZ
MEMOREX
MGA
MITSUBISHI
MTC
NAD
OPTONICA
PANASONIC
PHILCO
PHILIPS
PROTON
PULSAR
QUASAR
RADIO SHACK
0071
0651
0251
0251
0651
0431
0231
0651
0121
0571
0951
1041
0251
0511
0571
0221
0431
0431
0511
0071
0591
0501
0211 0571
0071 0281 0441
0281 0411 0501
0071 0281 0441
0521 0571
0471 0481 0571
Brand name
Brand code
RCA
0971
1041
0631
0851
0331
0071
0471
0171
0491
0021
0181
0571
0721
0001
0071
0181
0851
0441
0201
0501
0471
0511
0171
0501
0371
0841
0201
0201
0201
0511
0201
0491
0281
0931
REALISTIC
RUNCO
SAMSUNG
0181 0201 0281
0651
0961 0971 0981
0281
0201
0581
0251
0571
0411
0231
0651
0351
0641
0501
0471
0371
0751
0521 0571
0851
0191 0221 0461
0611 0651
SANYO
SEARS
SHARP
SONY
SOUNDESIGN
SYLVANIA
TANDY
TECHNICS
0321
0571
0251
0511
0851
0501
0911
0111
0461
0191
0591
0331 0451 0501
0651 0771
TEKNIKA
TMK
VIDTECH
0571
0511
1061
0181
0501
0221
0611
0201 0501
0531 0761
WARDS
0201 0271
0651
0461 0471
0651
ZENITH
0071
0471
0501
0911
1001
0201
0501
0091 0281 0291
0651
0511 0531 0761
1071
0501
1001
0201
0501
0091
0651
0181
0501
0041
0201
0651
1081 1091 0201
0191
0211
0201
0511
0451
0481
0071
0591
0531
0511
1011
0501
0651
0281
1021 1031
0481 0321
0771
0291 0341
0251
0631
0081
0231
0671
0281
0661
0121
0241
0701
0411
0791
0171
0451
0711
0491
0571
0281
0571
0571
0201
0041
0471
0201
0681
0501
0121
0651
0501
Function setup
Brand name
0191 0221 0461
0611 0651 0371
0841
0851 0571 0201
0501 0511 0531 0761
0911
0251 0481 0501
0251
0501 0401 0411 0851
0501 0001 0191 0481
0851 0511 0571 0071
0441
1011 1021 1031
0501 0481 0321
0651 0771
67
Others
Before Calling Service
Personnel
Specifications
LIMITED WARRANTY DVD
VIDEO PLAYER
Others
Before Calling Service Personnel
Check the following guide for the possible cause of a problem before contacting service.
Symptoms and correction
Symptom
Cause
Correction
No power.
• The power plug is disconnected.
• Connect the power plug securely into the
wall outlet.
18
The DVD video player turned
off by itself.
• The automatic power off function turned
the unit off.
• Press the PLAY button.
27
No picture.
• The TV is not set to receive DVD signal
output.
• Select the appropriate video input mode
on the TV so the picture from the DVD
video player appears on the TV screen.
26
• The video cable is not connected securely.
• Connect the video cable securely into the
appropriate jacks.
• The equipment connected with the audio
cable is not set to receive DVD signal
output.
• Select the correct input mode of the
audio receiver so you can listen to the
sound from the DVD video player.
26
• The audio cable is not connected securely.
• Connect the audio cable securely into
the appropriate jacks.
18-23
• The audio receiver or TV is turned off.
• Turn on the equipment connected with
the audio cable.
26
• The setting of output sound format is
incorrect.
• Select the proper audio setting.
The playback picture has
occasional distortion.
• The disc is dirty.
• Eject the disc and clean it.
9
• It is in fast forward or fast reverse
playback.
• Sometimes a small amount of picture
distortion may appear. This is not a
malfunction.
–
Brightness is unstable or
noises are present in the
playback pictures.
• The effect of copy protection.
• Connect the DVD video player directly to
the TV. Avoid connecting the DVD video
player to a VCR or TV/VCR combination.
18
The DVD video player does
not start playback.
• No disc is inserted.
• Insert a disc.
26
• An unplayable disc is inserted.
• Insert a playable disc. (Check the disc
type and color system.)
10
• The disc is placed upside down.
• Place the disc with the playback side
down.
26
• The disc is not placed within the guide.
• Place the disc correctly inside the guide
on the disc tray.
26
• The disc is dirty.
• Clean the disc.
• The parental lock function is set.
• Cancel the parental lock function or
change the parental lock level.
Playback does not follow the
course of the disc’s program.
• It is in the mode of repeat playback,
memory playback, etc.
• These operations may prevent a proper
progress of the contents.
–
Buttons do not work.
• Power supply fluctuations or other
abnormalities such as static electricity may
interrupt correct operations.
• Turn the power on or off with the POWER
button. Or disconnect the power plug and
insert it into the wall outlet again.
–
The remote control does not
work properly.
• The remote control is not pointed at the
remote sensor of the DVD video player.
• Point the remote control at the remote
sensor of the DVD video player.
15
• The remote control is too far from the DVD
video player.
• Operate the remote control within about
7 m.
15
• The batteries in the remote control are
exhausted.
• Replace the batteries with new ones.
15
No sound.
70
Page
18, 19
42, 54
58
9
54, 62
Specifications
DVD video player / outputs / supplied accessories
DVD Video Player
Power supply
120 V AC, 60 Hz
Power consumption
18 W
Mass
3.5 kg
External dimensions
430 × 102 × 313 mm (W/H/D)
Signal system
Standard NTSC
Laser
Semiconductor laser, wavelength 650 nm / 780 nm
Frequency range
DVD linear sound : 48 kHz sampling 4 Hz to 22 kHz
96 kHz sampling 4 Hz to 44 kHz
Signal-to-noise ratio
More than 112 dB
Audio dynamic range
More than 106 dB
Harmonic distortion
Less than 0.001 %
Wow and flutter
Below measurable level (less than ±0.001 % (W.PEAK))
Operating conditions
Temperature: 5 °C to 35 °C, Operation status: Horizontal
Outputs
1.0 V (p-p), 75 Ω, negative sync., pin jack × 1
S video output
(Y) 1.0 V (p-p), 75 Ω, negative sync., Mini DIN 4-pin × 1
(C) 0.286 V (p-p), 75 Ω
Component video output
(Y) 1.0 V (p-p), 75 Ω, negative sync., pin jack × 1
(PB)/(PR) 0.7 V (p-p), 75 Ω, pin jack × 2
Audio output (BITSTREAM/PCM
OPTICAL)
Optical connector × 1
Audio output (BITSTREAM/PCM
COAXIAL)
0.5 V (p-p), 75 Ω, pin jack × 1
Audio output (2CH AUDIO)
2.0 V (rms), 220 Ω, pin jacks (L, R) × 1
Audio output (5.1CH SURROUND)
2.0 V (rms), 220 Ω, pin jacks × 6
Others
Video output
Supplied Accessories
Audio/video cable ................................................. 1
Remote control (SE-R0034) ................................. 1
Batteries (AAA) ..................................................... 2
Power cord ........................................................... 1
• Designs and specifications are subject to change without notice.
71
Others
LIMITED WARRANTY DVD VIDEO PLAYER
Toshiba America Consumer Products, Inc. (“TACP”), Toshiba Hawaii (“THI”) and Toshiba Canada Limited (“TCL”) make the
following limited warranties. These limited warranties extend to original purchaser or any person receiving this set as a gift
from the original purchaser and to no other purchaser or transferee.
Limited Ninety (90) Day Warranty
TACP/THI warrant this product against defects in materials
or workmanship for a period of ninety (90) days after the
date of original retail purchase. During this period, TACP/
THI will repair or replace a defective product or part, at their
option, with a new or refurbished product or part without
charge to you. You must deliver the entire product to a
TACP/THI Authorized Service Station. You are responsible
for all transportation and insurance charges for the unit to
and from the Authorized Service Station. If you live in the
U.S.A. you may, at your option, return your DVD Unit to:
Toshiba America Consumer Products Inc.
Returns Center
1420C Toshiba Dr.
Lebanon, TN 37087
Upon receipt we will, at our option, exchange the DVD Unit
with a new or refurbished unit. Canadian consumers are
requested to contact TCL. In Hawaii consumers are
requested to contact THI.
Limited One (1) Year Warranty
TACP/THI further warrant the parts in this product against
defects in materials or workmanship for a period of one (1)
year after the date of original retail purchase. During this
period, TACP/THI will repair or replace a defective product
or part, at their option, with a new or refurbished product or
part without charge to you, except that if a defective part is
replaced after ninety (90) days from the date of the original
retail purchase you pay labor charges involved in the
replacement. You must also deliver the entire product to a
TACP/THI Authorized Service Station. You are responsible
for all transportation and insurance charges for the unit to
and from the Authorized Service Station. If you live in the
U.S.A. you may, at your option, return your DVD Unit to:
Toshiba America Consumer Products Inc.
Returns Center
1420C Toshiba Dr.
Lebanon, TN 37087
Upon receipt we will, at our option, exchange the DVD Unit
with a new or refurbished unit. Canadian Consumers are
requested to contact TCL. In Hawaii consumers are
requested to contact THI.
Rental Units
The warranty for rental units begin with the first rental or
thirty (30) days from the date of shipment to the rental firm,
whichever comes first.
72
Commercial Units
Products sold and used for commercial use have a limited
ninety (90) day warranty for all parts and labor.
Owner’s Manual
You should read the owner’s manual thoroughly before
operating this product. You should complete and mail the
enclosed Demographic card within ten (10) days after you,
or the person who has given you this product as a gift,
purchased this product. This is one way to enable TACP to
provide you with better customer service and improved
products. Failure to return the card will not affect your rights
under this warranty.
Your Responsibility
The above warranties are subject to the following
conditions:
(1) You must retain your bill of sale or provide other proof of
purchase.
(2) You must notify a TACP/THI/TCL /Authorized Service
Station within thirty (30) days after you discover a
defective product or part.
(3) All warranty servicing of this product must be made by a
TACP/THI/TCL Authorized Service Station.
(4) U.S.A. warranties are effective only if the product is
purchased and operated in the Continental U.S.A. or
Puerto Rico.
(5) Labor service charges for set installation. Set up,
adjustment of customer controls and installation or
repair of antenna systems are not covered by this
warranty. Reception problems caused by inadequate
antenna systems are your responsibility.
(6) Warranties extend only to defects in materials or
workmanship as limited above and do not extend to any
product or parts which have been lost or discarded by
you or to damage to products or parts caused by
misuse, accident, damage caused by Acts of God, such
as lighting or fluctuations in electric power, improper
installation, improper maintenance or use in violation of
instructions furnished by us; or to units which have
been altered or modified without authorization of TACP/
THI/TCL or to damage to products or part thereof which
have had the serial number removed, altered, defaced
or rendered illegible.
(7) Should you elect to return your DVD Unit to TACP after
the ninety (90) days and within one (1) year, or after the
warranty period has expired: Call (800)-631-3811 to
receive information concerning an exchange price.
Payment must be enclosed with product in the form of a
certified check or money order including reason for
return.
(8) Physically damaged DVD Units are not acceptable for
repair or exchange whether in or out of warranty and
will be returned as received.
How to Obtain Warranty Service
(1) Refer to the troubleshooting guide in your owner’s manual. This check list may solve your problem.
(2) In the U.S.A., only call the TACP toll free number 800-631-3811, or if in Hawaii or Canada see listing below within (30)
days after you find a defective product or part.
(3) Arrange for the delivery of the product to the TACP/THI/TCL Authorized Service Station or TACP Return Center.
Products shipped to the Service Station must be insured and safely and securely packed, preferably in the original
shipping carton, and a letter explaining the defect and also a copy of the bill of sale or other proof of purchase must be
enclosed.
In the Continental United States contact:
Toll Free
800-631-3811
In Hawaii contact:
Toshiba Hawaii Inc.
327 Kamakee Street
Honolulu, HA 96814
(808)-521-5377
In Canada contact:
Consumer Electronics Group
191 McNabb Street
Markham, Ontario L3R 8H2
(905)-470-5400
Consumer Electronics Group
22171 Fraserwood Way
Richmond, B.C. V6W 1J5
(604)-303-2500
Consumer Electronics Group
1643 North Service Road
Droval, QC H9P 1J1
(514)-856-4100
All warranties implied by state law, including the implied warranties of merchantability and fitness for a particular purpose, are
expressly limited to the duration of the limited warranties set forth above. With the exception of any warranties implied by state
law as hereby limited, the foregoing warranty is exclusive and in lieu of all other warranties, guarantees, agreements and
similar obligations of manufacturer or seller with respect to the repair or replacement of any parts. In no event shall TACP/THI
be liable for consequential or incidental damages.
No person, agent, distributor, dealer or company is authorized to change, modify or extend the terms of these warranties in
any manner whatsoever. The time within which an action must be commenced to enforce any obligation of TACP/THI arising
under the warranty or under any statute, or law of the United States or any state thereof, is hereby limited to ninety (90) days
from the date you discover or should have discovered, the defect. This limitation does not apply to implied warranties arising
under state law.
This warranty gives you specific legal rights and you may also have other rights which may vary from state to state. Some
states do not allow limitation on how long an implied warranty lasts, when an action may be brought, or the exclusion or
limitation of incidental or consequential damages, so the above provisions may not apply to you.
Others
ATTENTION CANADIAN CONSUMERS:
Canadian consumers are requested to complete the special Canadian “Warranty Registration Form” enclosed, and forward
this completed form with a copy of bill of sale to TOSHIBA OF CANADA to “Register and Validate” their warranty. Product
must be purchased from an Authorized Canadian Dealer. Products purchased in the U.S.A. and used in Canada are not
covered by these warranties.
IMPORTANT: PACKING AND SHIPPING INSTRUCTION
When you send the product to a Service Station, you must use the original carton box and packing material, then insert the
original carton box containing the unit into another carton using more packing material.
73
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement