Toshiba SDP1000 Portable DVD Player with Screen

Toshiba SDP1000 Portable DVD Player with Screen
Introduction
Basic playback
2
14
DIGITAL VIDEO
PORTABLE DVD PLAYER
SD-P1000
OWNER’S MANUAL
Advanced
playback
Function setup
Connections
Others
© 2000 TOSHIBA CORPORATION
A S
XZ2029P005
24
34
44
52
Introduction
SAFETY PRECAUTIONS
CAUTION:
This equipment employs a Laser System.
To ensure proper use of this product, please read this owner’s manual carefully and retain for
future reference. Should the unit require maintenance, contact an authorized service location see service procedure.
Use of controls or adjustments or performance of procedures other than those specified herein
may result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open the enclosure.
Visible and invisible laser radiation when open and interlocks defeated.
DO NOT STARE INTO BEAM.
FCC NOTICE “Declaration of Conformity Information”
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
WARNING:
Only peripherals complying with the FCC class B limits may be attached to this equipment.
Operation with non-compliant peripherals or peripherals not recommended by Toshiba is likely
to result in interference to radio and TV reception.
Changes or modifications made to this equipment, not expressly approved by Toshiba, or
parties authorized by Toshiba, could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired
operation.
In the spaces provided below, record the Model and Serial No. located on the bottom of your DVD player.
Model No.
Retain this information for future reference.
2
Serial No.
Location of the required label
Introduction
3
Introduction
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS GIVEN IN THIS
OWNER’S MANUAL AND THOSE MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR
FUTURE REFERENCE.
This set has been designed and manufactured to assure personal safety. Improper use can result in electric
shock or fire hazard. The safeguards incorporated in this unit will protect you if you observe the following
procedures for installation, use and servicing. This unit is fully transistorized and does not contain any parts that
can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.
1. Read owner’s manual
After unpacking this
product, read the owner’s
manual carefully, and
follow all the operating
and other instructions.
2. Power Sources
This product should be operated
only from the type of power
source indicated on the label. If
you are not sure of the type of
power supply to your home,
consult your product dealer or
local power company. For
products intended to operate from battery
power, or other sources, refer to the operating
instructions.
3. Ventilation
Slots and openings in
the cabinet are provided
for ventilation and to
ensure reliable operation
of the product and to
protect it from
overheating, and these
openings must not be blocked or covered. The
openings should never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product should not be placed in a
built-in installation such as a bookcase or rack
unless proper ventilation is provided or the
manufacturer’s instructions have been adhered
to.
4
4. Heat
The product should be
situated away from heat
sources such as
radiators, heat registers,
stoves, or other products
(including amplifiers) that
produce heat.
5. Water and Moisture
Do not use this product near
water - for example, near a
bath tub, wash bowl, kitchen
sink, or laundry tub; in a wet
basement; or near a
swimming pool and the like.
6. Cleaning
Unplug this product from
the wall outlet before
cleaning. Do not use liquid
cleaners or aerosol
cleaners. Use a damp
cloth for cleaning.
8. Overloading
Do not overload wall
outlets; extension cords, or
integral convenience
receptacles as this can
result in a risk of fire or
electric shock.
9. Lightning
For added protection for
this product during an
electrical storm, or when
it is left unattended and
unused for long periods
of time, unplug it from the
wall outlet. This will
prevent damage to the
product due to lightning and power-line surges.
10. Object and Liquid Entry
Never insert objects of any
kind into this product
through openings as they
may touch dangerous
voltage points or short-out
parts that could result in a
fire or electric shock. Never
spill liquid of any kind on the product.
11. Attachments
Do not use attachments not recommended by
the product manufacturer as they may cause
hazards.
12. Accessories
Do not place this product on
an unstable cart, stand, tripod,
bracket, or table. The product
may fall, causing serious
injury to a child or adult, and
serious damage to the
product. Use only with a cart,
stand, tripod, bracket, or table
recommended by the manufacturer, or sold
with the product. Any mounting of the product
should follow the manufacturer’s instructions,
and should use a mounting accessory
recommended by the manufacturer.
A product and cart combination should be
moved with care. Quick stops, excessive force,
and uneven surfaces may cause the product
and cart combination to overturn.
Introduction
7. Power-Cord Protection
Power-supply cords
should be routed so that
they are not likely to be
walked on or pinched by
items placed upon or
against them, paying
particular attention to
cords at plugs, convenience receptacles, and
the point where they exit from the product.
S3125A
13. Lid
Be careful not to catch your
fingers in the disc holder
when closing the lid. It may
cause personal injury.
14. Headphones
When you use
headphones, keep the
volume at a moderate
level. If you use the
headphones continuously
with high volume sound, it
may cause hearing damage.
15. Disc
Do not use a cracked,
deformed, or repaired
disc. These discs are
easily broken and may
cause serious
personal injury and
product malfunction.
16. Disc Spin
Do not touch a spinning disc. When you open
the disc holder, the disc may have not stopped
spinning. Touching a spinning disc may cause
personal injury or damage to the product.
5
Introduction
IMPORTANT SAFETY INSTRUCTIONS
17. Heating up
Do not use the product
on your lap or other
parts of body, as it may
become heated. Even
low temperature may
cause inflaming or
blistering, if touched for
a prolonged period.
18. Supplied AC Adapter
Use the supplied AC adapter to operate the
product. Substitute devices not specified by the
manufacturer may result in fire or product
malfunction.
b) Never disassemble the battery
pack, as that could cause
leakage of alkaline solution or
other electrolytic substance.
19. Airline Passengers
When you use this
product in an airplane,
follow the instructions of
the airline. Disregarding
them may cause harmful
interference to radio
communication.
c) Never short-circuit the battery
pack by either accidentally or
intentionally bringing the
terminals in contact with
another metal object. This
could cause personal injury
or a fire, and could also
damage the battery pack.
20. Pick-up Lens and Laser Beam
Do not look close the
pick-up lens or stare into
laser beam. Doing so
may cause damage to
eyesight.
d) Never hammer a nail into
the battery pack.
Never hit a hammer on the
battery pack.
Never step or tread on the
battery pack.
21. Traffic
Do not use this product
while walking or driving.
Neglecting this may
cause a traffic accident.
e) If you ever detect the
emission of an extraordinary
odor, excessive heat,
discoloration, or deformation
of the battery pack, remove
it from the player or the
battery charger immediately, and discontinue
use of the battery pack.
22. LCD
Should the LCD panel be
broken and liquid leaks
out, do not inhale or
swallow it. Doing so may
cause poisoning.
If you have got it into
your mouth, wash it out
and consult your doctor. If your hands or
clothes have touched it, wipe them with
alcohol and a cleaning cloth and then wash
them well.
6
23. Battery Pack
a) Never throw the battery pack into a
fire, as that could cause the battery
pack to explode.
Never heat the battery pack, as that
could cause leakage of alkaline
solution or other electrolytic
substance.
f) If you ever detect rust, the
emission of an
extraordinary odor,
excessive heat or anything
unusual of the battery pack
before starting to use it, do
not use it. Take it to an authorized Toshiba
service provider.
h) Never dispose of used
battery packs with other
ordinary solid wastes, since
they contain toxic
substances. Always dispose
of used battery packs in
accordance with the
prevailing community regulations that apply to
the disposal of batteries. Cover the metal
terminals with insulating tape, in order to
prevent accidental short-circuiting.
i) Always confirm that the
battery pack is compatible
with your player, before
attaching the battery pack
to the player.
j) Never expose the terminals
of the battery pack to any
other metal object. Wrap the
battery or place it in a
protective plastic bag,
whenever transporting it.
k) Always confirm that the
temperature is 5-35˚C before
you charge the battery.
Leakage, excessive heat, or
deterioration of the battery pack
may occur if this warning is not
heeded.
m) Never expose the battery
pack to direct sunlight.
Never store or use the
battery pack in a locked
and unventilated vehicle.
(where excessive internal
temperatures may be
encountered.)
Introduction
g) Keep the battery pack
away from heat or fire, if
you detect the emission of
an extraordinary odor or
leakage of alkaline
solution or other
electrolytic substance.
n) Always keep the battery
pack out of reach of infants
or small children.
o) Never shock the battery pack by
dropping or throwing it.
p) If the liquid contained within
the battery pack leaks, use
a large amount of water and
immediately wash off any
liquid which may
accidentally contact any
part of the body. Remove
any liquid that has
contacted your clothes by washing them
immediately with a detergent.
q) Always confirm that a
“click” sound has resulted,
when attaching the battery
pack to the player. That
sound confirms that the
battery pack has been
properly attached.
l) Never expose the battery
pack to any liquid.
7
Introduction
IMPORTANT SAFETY INSTRUCTIONS
24. Damage Requiring Service
Unplug this product from the wall outlet and
refer servicing to qualified service personnel
under the following conditions:
a) When the power-supply cord or plug is
damaged.
b) If liquid has been spilled, or objects have
fallen into the product.
c) If the product has been exposed to rain or
water.
d) If the product does not operate normally by
following the operating instructions. Adjust
only those controls that are covered by the
operating instructions as an improper
adjustment of other controls may result in
damage and will often require extensive
work by a qualified technician to restore the
product to its normal operation.
e) If the product has been dropped or damaged
in any way.
f) When the product exhibits a distinct change
in performance - this indicates a need for
service.
25. Servicing
Do not attempt to service this
product yourself as opening
or removing covers may
expose you to dangerous
voltage or other hazards.
Refer all servicing to qualified
service personnel.
26. Replacement Parts
When replacement parts are required, be sure
the service technician has used replacement
parts specified by the manufacturer or have the
same characteristics as the original part.
Unauthorized substitutions may result in fire,
electric shock, or other hazards.
27. Safety Check
Upon completion of any
service or repairs to this
product, ask the service
technician to perform
safety checks to determine
that the product is in
proper operating condition.
8
Precautions
Do not shock the LCD panel. It may cause unit
damage and malfunction.
When shipping the player, the original shipping carton
and packing materials come in handy. For maximum
protection, repack the unit as it was originally
packaged at the factory.
Do not use volatile liquids, such as insect spray, near
the player. Do not leave rubber or plastic products in
contact with the player for a long time. They will leave
marks on the finish.
The top and rear panels of the player may become
warm after a long period of use. This is not a
malfunction.
When the player is not in use, be sure to remove the
disc and turn off the power.
If you do not use the player for a long period, the unit
may not function properly in the future. Turn on and
use the player occasionally.
Notes on locating
When you place this player near a TV, radio, or VCR,
the playback picture may become poor and the sound
may be distorted. In this case, move the player away
from the TV, radio, or VCR.
Notes on moisture condensation
Moisture condensation damages the player. Please
read the following carefully.
Moisture condensation occurs, for example, when you
pour a cold drink into a glass on a warm day. Drops of
water form on the outside of the glass. In the same way,
moisture may condense on the optical pick-up lens
inside this unit, one of the most crucial internal parts of
the player.
le of mo
Examp ensat isture
ion!
cond
Optical pick-up
lens
Moisture condensation occurs during the
following cases.
When you bring the player directly from a cold place
to a warm place.
When you use the player in a room where you just
turned on the heater, or a place where the cold wind
from the air conditioner directly hits the unit.
In summer, when you use the player in a hot and
humid place just after you move the unit from an air
conditioned room.
When you use the player in a humid place.
Notes on cleaning
Use a soft, dry cloth for cleaning.
For stubborn dirt, soak the cloth in a weak detergent
solution, wring well and wipe. Use a dry cloth to wipe
it dry.
Do not use any type of solvent, such as thinner and
benzine, as they may damage the surface of the
player.
If you use a chemical saturated cloth to clean the unit,
follow that product’s instructions.
When cleaning the LCD panel, use a soft, dry cloth.
To obtain a clear picture
The player is a high technology, precision device. If the
optical pick-up lens and disc drive parts are dirty or worn
down, the picture quality becomes poor. To obtain a
clear picture, we recommend regular inspection and
maintenance (cleaning or parts replacement) every
1,000 hours of use depending on the operating
environment. For details, contact your nearest dealer.
Introduction
Notes on handling
It’s too
warm!
Do not use the player when moisture
condensation may occur.
If you use the player in such a situation, it may
damage discs and internal parts. Remove the disc,
connect the power cord of the player to the wall
outlet, turn on the player, and leave it for two or three
hours. After two or three hours, the player will have
warmed up and evaporated any moisture. Keep the
player connected to the wall outlet and moisture
condensation will seldom occur.
Wa
it!
Wall outlet
9
Introduction
Notes and Information
Playable discs
Structure of disc contents
This player can play the following discs.
Disc Mark
Contents
Disc
Size
Maximum
playback time
Approx. 4 hours
(single sided disc)
12 cm
Audio
+
video
(moving
pictures)
DVD
video
discs
Normally, DVD video discs are divided into titles, and
the titles are sub-divided into chapters. VIDEO CDs and
audio CDs are divided into tracks.
DVD video disc
DVD video disc
Title 1
Approx. 8 hours
(double sided disc)
Chapter 1
Title 2
Chapter 2
Chapter 1
Chapter 2
Chapter 3
Approx. 80 minutes
(single sided disc)
8 cm
Approx. 160 minutes
(double sided disc)
VIDEO CD/audio CD
VIDEO CD/audio CD
Track 1
VIDEO
CDs
DIGITAL VIDEO
Audio
CDs
Audio
+
video
(moving
pictures)
12 cm
Approx. 74 minutes
8 cm
Approx. 20 minutes
12 cm
Approx. 74 minutes
8 cm
(CD
single)
Approx. 20 minutes
Track 3
Track 4
Track 5
Each title, chapter or track is assigned a number, which
is called “title number”, “chapter number” or “track
number” respectively.
There may be discs that do not have these numbers.
On VIDEO CDs
Audio
The following discs are also available.
DVD-ROM
CD-RW
DVD-R
CD-R
CD-ROM
• You cannot play discs other than those listed above.
• You cannot play discs of DVD-RAM, DVD-RW, etc. or
non-standardized discs, even if they may be labeled
as above.
• This player uses the NTSC color system, and cannot
play DVD video discs recorded in any other color
system (PAL, SECAM, etc.).
Notes on region numbers
The region number of this player is 1. If region numbers,
which stand for their playable area, are printed on your
DVD video disc and you do not find 1 or ALL , disc
playback will not be allowed by the player. (In this case,
the player will display a message on-screen.)
10
Track 2
This player supports VIDEO CDs equipped with the
PBC (Version 2.0) function. (PBC is the abbreviation of
Playback Control.)
You can enjoy two playback variations depending on
types of discs.
• VIDEO CD not equipped with PBC function
(Version 1.1)
Sound and movie can be played on this player in the
same way as an audio CD.
• VIDEO CD equipped with PBC function
(Version 2.0)
In addition to operation of a VIDEO CD not equipped
with the PBC function, you can enjoy playback of
interactive software with search function by using the
menu displayed on the screen (Menu Playback).
Some functions described in this owner’s manual may
not work with all discs.
About this owner’s manual
Do not touch the playback side of the disc.
Playback side
Do not attach paper or tape to discs.
Introduction
On handling discs
This owner’s manual explains the basic instructions of
this player. Some DVD video discs are produced in a
manner that allows specific or limited operation during
playback. As such, the player may not respond to all
operating commands. This is not a defect in the player.
Refer to instruction notes of discs.
“ ” may appear on the screen during operation.
A “ ” means that the operation is not permitted by the
player or the disc.
Notes on copyright
On cleaning discs
Fingerprints and dust on the disc cause picture and
sound deterioration. Wipe the disc from the center
outwards with a soft cloth. Always keep the disc
clean.
If you cannot wipe off the dust with a soft cloth, wipe
the disc lightly with a slightly moistened soft cloth and
finish with a dry cloth.
Do not use any type of solvent such as thinner,
benzine, commercially available cleaners or antistatic
spray for vinyl LPs. It may damage the disc.
On storing discs
Do not store discs in a place subject to direct sunlight
or near heat sources.
Do not store discs in places subject to moisture and
dust such as a bathroom or near a humidifier.
Store discs vertically in a case. Stacking or placing
objects on discs outside of their case may cause
warping.
It is forbidden by law to copy, broadcast, show,
broadcast on cable, play in public, and rent copyrighted
material without permission.
DVD video discs are copy protected, and any recordings
made from these discs will be distorted.
This product incorporates copyright protection
technology that is protected by method claims of certain
U.S. patents and other intellectual property rights owned
by Macrovision Corporation and other rights owners.
Use of this copyright protection technology must be
authorized by Macrovision Corporation, and is intended
for home and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.
Exemptions
Toshiba Corporation is not liable for any damage
caused by fire, earthquake, uses by a third person,
accidents, owner’s intentional or unintentional
misuse, or uses in other improper conditions.
Toshiba Corporation is not liable for incidental
damages (such as profit loss or interruption in
business, etc.) caused by use or misuse of this
player.
Toshiba Corporation is not liable for any damage
caused by neglect of the instructions described in the
owner’s manual.
Toshiba Corporation is not liable for any damage
caused by misuse or malfunction through joint use of
this player and the connected equipment or software
that Toshiba Corporation is not concerned.
11
Introduction
Table of Contents
Introduction
SAFETY PRECAUTIONS .......................... 2
IMPORTANT SAFETY INSTRUCTIONS ... 4
Precautions ............................................... 9
Notes and Information ........................... 10
Notes on region numbers ............................... 10
Table of Contents.................................... 12
Basic playback
Selecting a subtitle language ......................... 30
Selecting a Language ............................. 31
Selecting a playback audio setting ................. 31
Viewing the Operational Information .... 32
Checking the operational status ..................... 32
Checking the remaining time and setting
status ............................................................ 32
Function setup
Playing a Disc ......................................... 14
Customizing the Function Settings ...... 34
Basic playback ............................................... 14
Setting procedure ........................................... 34
Setting details ................................................. 36
Variable Speed Playback ........................ 18
Playing in fast reverse or fast forward
directions ...................................................... 18
Playing frame by frame .................................. 18
Playing in slow-motion .................................... 19
Resuming playback from the same location ... 19
Locating a Specific Title, Chapter, or
Track ........................................................ 20
Locating a title using the top menu ................. 20
Locating a title by entering the title number .... 20
Locating a specific chapter or track directly ... 21
Locating a specific chapter or track ................ 21
Advanced playback
Playback From a Memorized Location .... 24
Storing locations in the memory ..................... 24
Accessing a Specific Location Directly .. 24
Entering the time of the desired location ........ 24
Playing Repeatedly ................................. 25
Repeating a title, chapter, or track .................. 25
Repeating a specific segment ........................ 25
Playing in a Favorite Order .................... 26
Setting titles, chapters, or tracks in a favorite
order ............................................................. 26
Table of Languages ................................ 42
Connections
Power Connection .................................. 44
Using the battery pack .................................... 45
Connecting to a TV ................................. 46
Connecting to Optional Equipment ...... 48
Connecting to an amplifier equipped with a
Dolby Digital decoder ................................... 48
Connecting to an amplifier equipped with
Dolby Pro Logic Surround ............................ 48
Connecting to an amplifier equipped with a
DTS decoder ................................................ 48
Connecting to an amplifier equipped with an
MPEG2 audio decoder ................................. 49
Connecting to an amplifier equipped with a
digital audio input ......................................... 49
Connecting to a PC ................................ 50
Others
Before Calling Service Personnel ......... 52
Specifications ......................................... 53
Identification of Controls ....................... 54
Zooming a Picture .......................................... 28
Main unit ......................................................... 54
Side view ........................................................ 55
Remote control ............................................... 56
Loading batteries ............................................ 57
Operating with the remote control .................. 57
Selecting 3-D (N-2-2) Sound
Enhancement .......................................... 28
LIMITED WARRANTY PORTABLE DVD
PLAYER ................................................... 58
Playing in Random Order ....................... 27
Playing titles, chapters or tracks in
random order ................................................ 27
Zooming a Picture .................................. 28
Selecting 3-D (N-2-2) sound enhancement .... 28
Selecting a Camera Angle ..................... 29
Changing the camera angle ........................... 29
12
Selecting Subtitles ................................. 30
Basic playback
Begin your operation.
Playing a Disc
Variable Speed Playback
Locating a Specific Title,
Chapter, or Track
Basic playback
Playing a Disc
This section shows you the basics on how to play a disc.
indicates a reference page of this manual.
See the page in
for details.
DVD
VCD
CD
CAUTION
• Keep your fingers well clear of the disc as it is spinning.
Neglecting to may cause serious personal injury.
• Be careful not to catch your fingers in the disc holder.
• Do not use a cracked, deformed, or repaired disc.
Basic playback
Preparations
• Make all connections and settings as necessary referring to
the connections chapter ( 44 ).
• When you want to view a disc on a connected TV or monitor,
turn on the equipment and select the video input connected
to the player.
• When you want to enjoy the sound of discs from an audio
system, turn the audio system on and select the input
connected to the player.
• If you use the supplied remote control, make sure that
batteries are loaded in it. 57
• Press the button on the front center to open the top cover.
1
Turn on the power.
POWER ON
POWER
Press POWER ON ( ) on the main
unit.
Alternatively press POWER on the
remote control.
The player turns on and the POWER/CHG
indicator on the player illuminates in green.
When the player is turned on for the first time,
an initial set-up display appears. See “Initial
set-up” and make the proper settings before
proceeding to step 2.
Push here.
2
Open the cover.
Press
OPEN
on the main unit.
Alternatively press OPEN on the
remote control.
Do not try to open the cover without using the
these buttons.
The cover is designed to stop at two positions.
Do not force the cover open further, as it may
cause damage to the player.
POWER/CHG indicator
4
3
Set a disc.
Slide the rim under the
stopper.
Stopper
MENU
TOP MENU
VOLUME
2
ENTER
1,5
Place a disc with the playback side down, and
push gently on the center of the disc to fix it to the
spindle.
4
14
Close the cover.
Press PUSH CLOSE on the left corner.
2
To obtain a higher quality picture
DIMMER
Occasionally, some picture noise not usually visible during a normal broadcast may
appear on the TV screen while playing a DVD video disc because the high
resolution pictures on these discs include a lot of information. While the amount of
noise depends on the TV you use with this player, you should generally reduce the
sharpness adjustment on your TV when viewing DVD video discs.
1
SETUP
TOP MENU
/ / /
ENTER
About
MENU
5
VCD
CD
Initial set-up
Start playback.
Press
PLAY
Make the following settings on the display.
on the main unit.
Alternatively press PLAY on the
remote control.
If you select a DVD video disc that contains a top
menu, or select a PBC (Playback Control)featured VIDEO CD ( 10 ), a menu may appear.
See “Locating a title using the top menu”. 20
• You may need to press the TOP MENU or MENU
button to display disc menu (depending on the
actual DVD video disc.)
Notes
• Do not put any objects other than discs in the disc holder.
• Do not move or shake the main unit while playing. It may
damage the disc.
• In many instances, a menu screen will appear after playback
of a movie is completed. Prolonged display of an on-screen
menu may damage your television set, permanently etching
that image onto its screen. To avoid this, be sure to press the
(STOP) button (or STOP button on the remote control)
once the movie is completed.
• This player is equipped with a high-speed disc drive
mechanism to support DVD-ROM/CD-ROM discs.
Therefore, there may be some vibration in the unit. This is
not a malfunction. (The degree of vibration varies depending
on the disc.)
On-screen Language: Select the appropriate
on-screen language.
TV Shape: Select a picture size according to the aspect
ratio of your TV. When you use the LCD of this player,
select “16:9LCD.” (See 37 for details.)
TOSHIBA
Thank you for your purchase of TOSHIBA Portable
DVD player. Please make a selection
for On-Screen Language and your TV Shape and
press ENTER button on your remote control.
FIRST SETUP
On-Screen Language
TV Shape
ENG
LCD
1 Press / to select “On-Screen Language,” and
press ENTER.
2 Select a language using / , and press ENTER.
3 Press to select “TV Shape,” and press ENTER.
4 Select a picture size using / , and press ENTER.
5 Finally press SETUP on the remote control.
All your selections are entered and the display
disappears.
To change your settings, see “Customizing the Function
Settings.” 34
To change LCD brightness
Press DIMMER.
DIMMER
Each time you press DIMMER,
brightness alternates between two
levels.
To adjust the volume of the speakers or the
connected headphones
Turn VOLUME control.
VOLUME
15
Basic playback
STOP
5
DVD
The DVD VCD CD icons on the heading bar show the playable discs relevant to the
function described under each heading.
DVD : You can use this function with DVD video discs.
VCD : You can use this function with VIDEO CDs.
CD
: You can use this function with audio CDs.
Basic playback
Playing a Disc (continued)
OPEN
POWER
PLAY
PAUSE/STEP
STOP
Basic playback (continued)
To pause playback (still mode)
Press (or PAUSE/STEP on the remote control) during
playback.
PAUSE/STEP
POWER/CHG indicator
To resume normal playback, press
(PLAY) (or PLAY on the remote
control).
• Sound is muted during still mode.
RETURN
To stop playback
Press
(or STOP on the remote control).
STOP
To turn off the power
Press and hold POWER OFF ( ) on the main unit for
about 2 seconds.
OFF
Alternatively press POWER on the remote control.
POWER
To remove the disc
Press
cover.
(or OPEN on the remote control) to open the
OPEN
Remove the disc from under the rim
while gently pressing down on its
center.
CAUTION
Do not touch the spindle immediately after prolonged play,
as it may have become hot.
Be careful in loading/removing a disc.
16
Hold function
If you pause a picture of a DVD video disc and leave it
still for a long while, the screen saver of the player
automatically appears (when “Screen Saver” is set to
“On” 40 ). To turn off the screen saver, press the
(PLAY) (or PLAY on the remote control) button.
The buttons on the player and remote control can be
locked, so that you can avoid unintended operation
while carrying the player.
Basic playback
About the screen saver
Press and hold RETURN on the player for longer than
approximately 2 seconds.
Automatic Power Off function
If the player is stopped, or the screen saver is engaged
for approximately 20 minutes, the player will
automatically turn itself off.
About the LCD
• Although the LCD incorporates high precision
technology in its design, please understand that
there may be slight pixel breakup or stray light
emissions of 0.01% or less.
• The fluorescent tube which illuminates the panel
from the inside will deteriorate with use. (The
standard life length is about 10,000 hours of
continuous use at normal temperature.) When the
LCD becomes dim, flickers, or does not illuminate,
contact your dealer for replacement.
RETURN
The buttons are locked.
HOLD
To release the buttons, press and hold RETURN on the
player for longer than approximately 2 seconds.
Notes
• When you lock or release the buttons, the POWER/CHG
indicator flashes three times.
• If a button is pressed while it is locked, the POWER/CHG
indicator will flash rapidly.
If the cover will not open
Open the cover manually as shown below when it is
locked by power failure or other causes.
Bottom of the
player
Slide the pin in the arrow’s
direction using a slender
object with a fine tip.
17
Basic playback
Variable Speed Playback
You can play discs at various speeds, and resume playback from the location
where you stopped playback.
REV
PLAY
FWD
PAUSE/STEP
SLOW
STOP
DVD
VCD
CD
Playing in fast reverse or fast forward directions
To resume normal playback
Press REV or FWD during playback.
Press PLAY.
REV
PLAY
REV: Fast reverse playback
FWD: Fast forward playback
FWD
DVD
Each time you press the REV or
FWD button, the playback speed
changes.
2
x2 the normal
speed
VCD
CD
8
x8 the normal
speed
30
Notes
• The player mutes sound and omits subtitles during reverse
and forward scan of DVD video discs. However, the player
plays sound during fast forward or fast reverse play of audio
CDs.
• The playback speed may vary depending on the disc.
x30 the normal
speed
Each time you press the REV or
FWD button, the two playback
speeds alternate.
FR1
FR2
Fast reverse
playback
FF1
FF2
Fast forward
playback
DVD
VCD
Playing frame by frame
Press PAUSE/STEP during still playback.
PAUSE/STEP
Each time you press the PAUSE/
STEP button, the picture advances
one frame.
To resume normal playback
Press PLAY.
PLAY
Note
The sound is muted during frame by frame playback.
18
Playing in slow-motion
To resume normal playback
Press SLOW during playback.
SLOW
DVD
VCD
CD
1
Press PLAY.
Each time you press the SLOW
button, the slow-motion speed
changes.
PLAY
1 2
1 4
1 8
1/2 the normal
speed
1/4 the normal
speed
1/8 the normal
speed
Notes
• The sound is muted during slow-motion playback.
• The playback speed may vary depending on the disc.
Resuming playback from the same location
Press STOP at the location where you
want to interrupt playback.
STOP
2
Basic playback
DVD
The player memorizes the location
where playback is stopped.
Press PLAY.
PLAY
The player resumes playback from
the location where you stopped
playback.
To start playback from the beginning regardless
of the location where you stopped playback
1 Press STOP twice.
STOP
The player’s memory is cleared.
2 Press PLAY.
PLAY
DVD
Playback starts from the
beginning of the current title.
VCD
CD
Playback starts from the
beginning of the disc.
• If you want to return to the beginning of a DVD video
disc, turn the power off and on by pressing the
POWER button, and then start playback.
Notes
• The player’s memory is also cleared when:
– you change the parental lock setting 40 or select a disc
menu language 36 .
– you use a PBC-featured VIDEO CD while “PBC” is set to
“On” 41 .
• There may be a difference in the location where playback
resumes depending on the disc.
• Settings you changed using the on-screen displays while the
player keeps a location in the memory may function only
after the memory is cleared.
19
Basic playback
Locating a Specific Title, Chapter, or Track
Normally, DVD video discs are divided into titles, and the titles are sub-divided into chapters. VIDEO CDs and audio CDs
are divided into tracks. You can quickly locate any specific title, chapter, or track.
DVD video disc
Title 1
Chapter 1 Chapter 2
DVD
1
Chapter 1
Press TOP MENU.
The top menu appears.
TOP MENU
Press
want.
ENTER
DVD
1
/
/
TITLE 1
TITLE 2
TITLE 3
TITLE 4
/
to select the title you
If the titles in the top menu are
assigned a number, you can directly
locate a specific title by pressing its
designated number with the number
buttons.
Track 2
Track 3
Track 4
Track 5
3
Press ENTER.
Playback starts from chapter 1 of the
selected title.
Notes
• The instructions above describe basic procedures which
may vary depending on the contents of the DVD video disc.
If different instructions appear on the screen, follow those
instructions.
• If you display the top menu during playback and press the
TOP MENU button again without selecting any title, the
player may resume playback from the point where you first
pressed the TOP MENU button (depending on the actual
DVD video disc.)
• This method of locating a title is available only on a disc that
contains a top menu.
• Instruction notes of discs may refer to the button that
displays the top menu as TITLE button.
Locating a title by entering the title number
Press T.
T
Make sure that the space next to
“Title” is highlighted.
(You can shift the highlight using the
/ buttons.)
1
Press the corresponding number
buttons for the title you want.
e.g. To select title 2
To select title 12
20
Track 1
ENTER
Title : 1
Chapter:
2
VIDEO CD/Audio CD
Chapter 3
Locating a title using the top menu
e.g.
2
Title 2
Chapter 2
2
1
2
3
Press PLAY.
PLAY
Playback starts from chapter 1 of
the selected title.
Notes
• Pressing the CLEAR button resets the title and chapter
numbers. To clear the “Title” and “Chapter” display, press
the T button several times.
• This method of locating a title is available only on a disc that
contains title numbers.
TOP MENU
Number buttons
T
ENTER
/ / /
CLEAR
PLAY
SKIP
1
Locating a specific chapter or track directly
Press T.
Skip steps 1 and 2 if you are using a VIDEO CD/
audio CD.
T
2
Title : 1
Chapter:
1
Press to highlight the space next to
“Chapter.”
Title : 1
Chapter:
ENTER
3
Basic playback
DVD
VCD
CD
1
4
Press PLAY.
PLAY
Playback starts from the selected
chapter or track.
To select a title and chapter number at the same
time
Perform step 1, and enter a title number you want in the
space next to “Title” using the number buttons, then
perform steps 2 to 4.
Note
Pressing the CLEAR button resets the title and chapter
numbers. To clear the “Title” and “Chapter” display, press the
T button several times.
Press the corresponding number
buttons for the chapter or track you
want.
You can use the +10 button to select numbers
from 10 through 99.
e.g. To select chapter or track 25
2
or +10
DVD
VCD
CD
5
+10
5
Locating a specific chapter or track
Press SKIP ( / ) repeatedly to display
the chapter or track number you want.
Playback starts from the selected chapter or track.
SKIP
To locate succeeding chapters or tracks
SKIP
Notes
• Some titles may not display chapter numbers.
• When you set “Title Stop” to “Off” 41 , you can access
chapters in another title. If you go back to the preceding title
by pressing the SKIP
button, the player locates the first
chapter of the title. When “Title Stop” is set to “On,” you can
access chapters only within the current title.
Playback starts from the beginning of the
current chapter or track.
When you press twice, playback starts
from the beginning of the preceding
chapter or track.
21
Advanced playback
Customizing the performance of your player.
Playback From a Memorized
Location
Locating a Specific Location
Directly
Playing Repeatedly
Playing in a Favorite Order
Playing in Random Order
Zooming a Picture
Selecting 3-D (N-2-2) Sound
Enhancement
Selecting a Camera Angle
Selecting Subtitles
Selecting a Language
Viewing the Operational
Information
Advanced playback
Playback From a Memorized Location
The player memorizes a specific location on a disc, so that you can resume
playback from there later.
DISC/MEMO
Storing locations in the memory
DVD
Press DISC/MEMO at the location where
you want to resume playback later.
DISC/MEMO
Disc M emory Set
To start playback from the location you stored
Insert a disc that contains the location you stored, and
press DISC/MEMO during stop.
DISC/MEMO
The DISC/MEMO button can be pressed also while
you are playing in slow-motion or the picture is
paused.
Some discs begin playback
automatically. In such a case, first
stop playback by pressing STOP, then
press DISC/MEMO.
Notes
• The player memorizes only one location on each side of a DVD video disc. It has the capability to memorize 3 different
locations (eg. 3 single sided discs). Storing a fourth memory location erases the first.
• Storing a new location erases a previous one on the disc.
• If you start playback of a DVD video disc equipped with the parental lock feature 40 , after changing the parental lock level
on the player, the display of the parental lock level may return to the previous one. In this case, set the parental lock level
back to it.
• Some discs or scenes (especially menus included on the disc) may not permit this operation.
Accessing a Specific Location Directly
You can access a specific location by entering its corresponding time (hours,
minutes, seconds).
2
1
3
DVD
VCD
CD
1
Entering the time of the desired location
Press T twice.
You may have to press further
depending on the disc. Press the
button repeatedly until the following
display appears.
T
Time
2
Press the number buttons to enter the
time.
e.g.
1
24
-:- - :- -
2
5
3
0
Time
1 : 25 : 30
3
Press PLAY.
PLAY
Playback starts from the desired
location.
Notes
• Some discs may not respond to this process.
• Some scenes may not be located precisely as you
specified.
• This method for accessing specific locations is available
only within the current title of the DVD video disc or within
the current track of the VIDEO CD/audio CD.
Playing Repeatedly
You can play a specific title, chapter, track, or segment repeatedly.
(Title repeat, chapter/track repeat, A-B repeat)
CLEAR
PLAY
REPEAT
A-B RPT
DVD
VCD
CD
Press REPEAT.
REPEAT
Each time you press the REPEAT
button, the repeat mode changes as
follows.
2
Press PLAY.
PLAY
Advanced playback
1
Repeating a title, chapter, or track
The player starts repeat playback.
Press the PLAY button within about
5 seconds after you press the
REPEAT button.
Chapter Repeat
DVD
Chapter Repeat
Repeats the same
chapter.
DVD
Title Repeat
Repeats the same title.
VCD
CD
Track Repeat
Repeats the same track.
VCD
CD
All Repeat
Repeats the entire disc.
Repeat Off
Resumes normal
playback.
DVD
VCD
CD
Repeating a specific segment
1
Press A-B RPT at the beginning of the
segment (point A) you want to play
repeatedly.
A-B RPT
2
Press CLEAR.
CLEAR
Note
Some discs may not permit repeat operation.
To resume normal playback
Press CLEAR.
CLEAR
A–
Press A-B RPT again at the end of the
segment (point B).
A-B RPT
To resume normal playback
The player automatically returns to
point A and starts repeat playback of
the selected segment (A-B).
Notes
• Some discs may not permit A-B repeat operation.
• You can specify a segment only within the current title or
track.
• You cannot set the A-B repeat function for a segment that
includes multiple camera angles 29 .
• There may be a slight difference between point A and the
location where playback actually resumes depending on the
disc.
A–B
25
Advanced playback
Playing in a Favorite Order
You can combine your favorite titles, chapters, or tracks and play them in the
order you determine. You can program up to 28 selections into the memory.
(Memory playback)
Title: 2
Chapter: 25
Title: 2
Chapter: 12
Title: 1
Chapter: 1
DISPLAY
2
2
/ / /
CLEAR
3
1
DVD
VCD
CD
1
Setting titles, chapters, or tracks in a favorite order
Set a disc and press MEMORY during
stop.
MEMORY
The following display appears.
T: Title number or
track number
C: Chapter number
2
MEMORY
T C
1 –– ––
2 –– ––
3 –– ––
4 –– ––
5 –– ––
6 –– ––
7 –– ––
8
9
10
11
12
13
14
T
––
––
––
––
––
––
––
C
––
––
––
––
––
––
––
15
16
17
18
19
20
21
T
––
––
––
––
––
––
––
C
––
––
––
––
––
––
––
22
23
24
25
26
27
28
T
––
––
––
––
––
––
––
C
––
––
––
––
––
––
––
Select the items in the order you want
by pressing the number buttons, then
ENTER for each item.
Each time you press the / button, the space
of “T” and “C” is highlighted in turn. Highlight
where you want to enter, then press the
corresponding number buttons.
To select another chapter in the same title, you do
not need to select the title number.
To select tracks from a VIDEO CD/audio CD in
order, press the number buttons for the track, then
press the ENTER button for each selection you
want.
3
Press PLAY while the MEMORY display
appears on the screen.
PLAY
26
The player starts memory playback.
To change the programmed selections
1 While the MEMORY display appears on the screen,
press / to move the highlighted bar to the item
you want to change.
2 Change the selection following the instructions in
step 2.
To cancel the programmed selections
1 While the MEMORY display appears on the screen,
press / to move the highlighted bar to the item
you want to cancel.
2 Press CLEAR.
To resume normal playback from memory
playback
Press CLEAR.
CLEAR
To program during playback
If you press the MEMORY button during playback, a
programming display appears.
If you further press the DISPLAY button, you can
display the current MEMORY setting. Follow steps 2
and 3.
Notes
• Some discs may not permit memory playback operation.
• If you press the REPEAT button during memory playback,
the player repeats the current memory playback.
• If you press the MEMORY or RETURN button while the
MEMORY display appears on the screen, the MEMORY
display disappears.
• The programmed selections will be cleared when you turn off
the player.
Playing in Random Order
You can play titles, chapters within a title, or tracks in random order.
(Random playback)
Title: 1
Chapter: 3
Title: 2
Chapter: 2
CLEAR
Title: 3
Chapter: 1
2
1
DVD
VCD
CD
To resume normal playback
Press RANDOM.
RANDOM
Press CLEAR.
Each time you press the RANDOM
button, the random mode changes
as follows.
Chapter Random
DVD
Chapter Random Plays chapters in the
same title in random
order.
DVD
Title Random
VCD
CD
Track Random
Random Off
CLEAR
Notes
• Some discs may not permit random playback operation.
• You cannot use the random playback function in conjunction
with the memory playback feature.
Plays titles in random
order.
Plays tracks in random
order.
Resumes normal
playback.
If you press the RANDOM button
during playback, the player
automatically starts random
playback after finishing the current
title, chapter or track.
2
Press PLAY.
PLAY
The player starts random playback.
Press the PLAY button within about
5 seconds after you press the
RANDOM button.
27
Advanced playback
1
Playing titles, chapters or tracks in random order
Advanced playback
Zooming a Picture
You can magnify areas within a picture.
ZOOM
/
/
/
RETURN
CLEAR
DVD
Zooming a picture
Press ZOOM during normal, slow or still
playback.
As you repeatedly press the ZOOM
button, the magnification level
increases.
ZOOM
RETURN
To reduce the magnification level,
press the RETURN button.
ENTER
CLEAR
If you press the / / / buttons,
the zoom point shifts.
When the zoom point reaches an
edge of the picture, the color of
“Zoom” changes.
Pressing the CLEAR button restores
the zoom point to the center of the
picture.
To resume normal playback
Press ZOOM repeatedly so that “Zoom” disappears.
ZOOM
Notes
• Some discs may not respond to zoom feature.
• During some scenes, the buttons may not work as
described.
• Zooming does not work on subtitles or menus included on
DVD video discs.
• During zoom playback, the / / / buttons cannot work
on menus included on DVD video discs. If you want to view
the menus, cancel the zoom playback.
• The magnification level varies depending on the picture size
you select. 37
Selecting 3-D (N-2-2) Sound Enhancement
You can enjoy expansive virtual surround sound effects from just two speakers.
DVD
VCD
CD
Selecting 3-D (N-2-2) sound enhancement
Press 3D during playback.
3D
The current setting is displayed.
Each time you press the 3D button,
the setting changes as follows.
3D (N – 2 – 2 ) : Off
3D (N – 2 – 2 ) : On
3DHP (N – 2 – 2 For Headphone) : On
28
3D
Off
Notes
• You may sense a difference in volume between normal and
3-D (N-2-2) enhanced sound.
• 3-D (N-2-2) sound enhancement may not function (or may
not be realized) depending on the sound output setting or
recording system 31 .
• If 3-D (N-2-2) sound enhancement is on, Dolby Pro Logic
Surround may not function on output sounds at all, or may
function differently than usual.
On
This level is designed
especially for
headphone listening.
Spatializer® 3-Dimensional Sound Processing provided by Desper
Products. Inc.
Certain audio features of this product manufactured under a license
from Desper Products, Inc., Spatializer® and the circle-in-square
device are trademarks owned by Desper Products, Inc.
Selecting a Camera Angle
If a scene was recorded with multiple angles, you can easily change the
camera angle of the scene you are viewing.
1, 2
2
CLEAR
DVD
Press ANGLE while playing a scene
recorded with multiple angles.
ANGLE
While playing a scene recorded with
multiple angles, the angle icon ( )
appears on the screen.
Press the ANGLE button while the
angle icon is displayed.
Current angle number
Angle icon
Angle : 1
2
Press ANGLE or while the angle
number is displayed on the screen.
ANGLE
Each time you press the ANGLE or
button, the camera angle changes.
To turn off the angle number display
Press CLEAR.
CLEAR
To disable the angle icon display on the screen
From the on-screen displays, set “On-Screen Displays”
to “Off.” 40
The multi camera angle function is always active
regardless of this setting.
Notes
• You can change the camera angle during still playback. The
camera angle changes to the new setting when you resume
normal playback.
• If you pause a picture immediately after changing a camera
angle, the resumed playback picture may not display the
new camera angle.
e.g.
Angle : 1
ENTER
Angle : 2
Angle : 3
: Cycles backwards
You can change the camera angle directly by
pressing the number buttons corresponding to an
angle number instead of using the / buttons.
29
Advanced playback
1
Changing the camera angle
Advanced playback
Selecting Subtitles
You can display subtitles on the screen and select a subtitle language
from those included on the DVD video disc.
Good evening!
DVD
1
Bonsoir!
SUBTITLE
/ / /
CLEAR
¡Buenas tardes!
Selecting a subtitle language
Press SUBTITLE during playback.
SUBTITLE
The current subtitle setting is
displayed for about 3 seconds.
To turn subtitles on or off
1 Press SUBTITLE during playback.
SUBTITLE
Subtitle : 1 ENG On
Language
Position number
The abbreviation of the language appears instead
of the language name. Refer to the list of
languages and their abbreviations. 42
2
2 Press / while the subtitle setting is displayed on
the screen, to select “On” or “Off.”
Displayed for about 3 seconds.
ENTER
Subtitle : 1 ENG On
Press SUBTITLE or while the subtitle
setting is displayed on the screen.
SUBTITLE
Each time you press the SUBTITLE
or button, the subtitle languages
included on the DVD video disc
change.
Subtitles
e.g.
Subtitle : 1 ENG Off
ENTER
Subtitle : 1 ENG On
Good evening!
Subtitles are
not displayed.
Subtitle : 2 FRE On
Subtitle : 3 SPA On
: Cycles backwards
To turn off the subtitle setting
display, press the CLEAR button.
Notes
• Some DVD video discs display subtitles automatically, and
you cannot turn them off even if you set the subtitle function
to off.
• During some scenes, subtitles may not appear immediately
after you select “On.”
• Some DVD video discs will allow you to make subtitle
selections and turn subtitles on or off only via the disc menu.
Notes
• When you turn on the player or replace a disc, the player returns to the initial default setting 36 .
When you select a subtitle language which is not included on the disc, the player plays a prior language programmed on the
disc.
• During some scenes, the subtitles may not appear immediately after you change the subtitle language by pressing the /
buttons.
30
Selecting a Language
You can select a preferred language and sound recording system from those
included on the DVD video disc.
Good
morning!
1, 2
2
¡Buenos días!
Bonjour!
CLEAR
Selecting a playback audio setting
DVD
AUDIO
The current audio setting is
displayed for about 3 seconds.
Position
number
2
Press AUDIO or while the audio
setting is displayed on the screen.
AUDIO
Language
Recording system
Audio channel
Audio : 1 ENG PCM 2CH
Audio Out Select : Bitstream
Each time you press the AUDIO or
button, the audio settings included
on the DVD video disc change.
e.g.
Audio : 1 ENG PCM
ENTER
Output sound format
Audio : 2 FRE
39
Audio : 3 SPA PCM
The abbreviation of the language appears instead
of the language name. Refer to the list of
languages and their abbreviations. 42
Advanced playback
1
Press AUDIO during playback.
2CH
D 2CH
2CH
: Cycles backwards
If you press the / buttons, you
can select output sound format.
To turn off the audio setting display, press the
CLEAR button.
Selecting sound channels of VIDEO CDs
During playback, press AUDIO repeatedly to select the
sound channel.
AUDIO
Notes
• Some discs allow you to change audio selections only via
the disc menu. If this is the case, press the MENU button
and choose the appropriate language from the selections on
the disc menu.
• When you turn on the player or replace a disc, the player
returns to the initial default setting 36 .
If you select a sound track which is not included on the disc,
the player plays a prior sound track programmed on the disc.
Output sound conversion table (sampling frequency/quantization bit)
Discs
DVD video
discs
VIDEO CDs
Audio CDs
Recording system
Dolby Digital
48 kHz/16 bit
48 kHz/20 bit
48 kHz/24 bit
Linear PCM 96 kHz/16 bit
96 kHz/20 bit
96 kHz/24 bit
DTS
MPEG2
MPEG1
Linear PCM 44.1 kHz/16 bit
DTS
Audio selection from the menu 34 39 and output jacks on the rear panel
“Bitstream”
“Analog 2ch”
“PCM”
BITSTREAM/PCM AV OUT jack BITSTREAM/PCM AV OUT jack BITSTREAM/PCM AV OUT jack
jack
jack
jack
Bitstream
48 kHz/20 bit 48 kHz/16 bit 48 kHz/20 bit
48 kHz/20 bit
Bitstream
48 kHz/16 bit 48 kHz/16 bit 48 kHz/16 bit 48 kHz/16 bit 48 kHz/16 bit 48 kHz/16 bit
48 kHz/16 bit 48 kHz/20 bit 48 kHz/16 bit 48 kHz/20 bit 48 kHz/16 bit 48 kHz/20 bit
48 kHz/16 bit 48 kHz/20 bit
48 kHz/24 bit 48 kHz/16 bit 48 kHz/20 bit
48 kHz/16 bit 48 kHz/16 bit
96 kHz/16 bit 48 kHz/16 bit 48 kHz/16 bit
48 kHz/16 bit 48 kHz/20 bit
96 kHz/20 bit 48 kHz/16 bit 48 kHz/20 bit
48 kHz/16 bit 48 kHz/20 bit
96 kHz/24 bit 48 kHz/16 bit 48 kHz/20 bit
Bitstream
Bitstream
Bitstream
Bitstream
48 kHz/16 bit
48 kHz/16 bit 48 kHz/16 bit 48 kHz/16 bit
44.1 kHz/16 bit 44.1 kHz/16 bit 44.1 kHz/16 bit 44.1 kHz/16 bit 44.1 kHz/16 bit 44.1 kHz/16 bit
44.1 kHz/16 bit 44.1 kHz/16 bit 44.1 kHz/16 bit 44.1 kHz/16 bit 44.1 kHz/16 bit 44.1 kHz/16 bit
Bitstream
(Noise)
Bitstream
(Noise)
Bitstream
(Noise)
: 3-D (N-2-2) sound enhancement can function.
31
Advanced playback
Viewing the Operational Information
You can view information about a disc and its operational status on the screen.
DISPLAY
DVD
VCD
CD
Checking the operational status
Press DISPLAY during stop.
Each time you press the DISPLAY button, the on-screen display changes as follows.
DISPLAY
VCD
CD
DVD
Current title number
e.g.
e.g.
→
Stop
Title : 2
Chapter : 1
Operational
status
→
↓
Turns off.
DVD
VCD
CD
Current track number
Total playing time of the disc
Current chapter number
Track : 1
Total 0 : 46 : 30
Stop
Operational
status
↓
Turns off.
Checking the remaining time and setting status
Press DISPLAY during playback.
Each time you press the DISPLAY button, the on-screen display changes as follows.
DISPLAY
DVD
Current chapter number
Current title number Operational
status
Playback mode
e.g.
Play
Elapsed Remain
Title : 3 0 :10 : 15 0 : 50 : 45
Chapter : 2 0 :03 : 08 0 :10 : 24
Chapter Repeat
3D (N-2-2) : On
→
D 2 CH
Audio : 1 ENG
Subtitle : 12 ENG Off
Angle : 1
↓
Bit Rate 0
10
Elapsed time
and remaining
time of the
current title
Elapsed time
and remaining
time of the
current chapter
Current 3-D
(N-2-2) setting
Current audio
setting
Current subtitle
setting
Current angle
setting
6 . 0 Mbps
Data transfer rate (Mbit/s)
= Amount of picture, sound and subtitle data in the
DVD video disc transferred per second.
The larger the value is, the more data processed, but
this does not necessarily insure better picture quality.
↓
Turns off.
32
VCD
CD
e.g.
→
Operational status
Current track number
Playback mode
Play
Elapsed Remain
Track : 3 0 :01 : 20 0 : 02 : 00
0 :05 : 12 0 :43 : 00
Disc
Track Repeat
3D (N-2-2) : On
↓
Turns off.
Elapsed time
and remaining
time of the
current track
Elapsed time
and remaining
time of the disc
Current 3-D
(N-2-2) setting
Function Setup
You can change the default settings to customize
performance to your preference.
Customizing the Function
Settings
Table of Languages
Function setup
Customizing the Function Settings
You can change the default settings to customize performance to your
preference.
1, 6
2
RETURN
LANGUAGE
DVD
VCD
CD
1
PICTURE
DISPLAY
AUDIO
OPERATION
3, 4
Setting procedure
Press SETUP during stop.
SETUP
The following on-screen display
appears.
3
Press / to select the setting you
want to change, then press ENTER.
ENTER
PICTURE
LANGUAGE
On-Screen Language
Disc Menu Language
Audio Language
Subtitle Language
2
AUDIO
DISPLAY
ENTER
OPERATION
ENG
ENG
ENG
–––
4
Change the selection by / or other
buttons, by referring to the
corresponding pages 36 , then press
ENTER.
Press / to select a symbol for the
setting you want to change.
ENTER
ENTER
(See the next page.)
5
ENTER
Repeat steps 3 and 4 to change other
settings.
To select another operation, go back to step 2.
Language settings
6
LANGUAGE
Press SETUP.
SETUP
The on-screen display disappears.
Picture performance settings
PICTURE
To return to the previous display
Press RETURN.
RETURN
Output sound settings
AUDIO
Display settings
DISPLAY
Operational settings
OPERATION
34
Notes
• The on-screen display disappears when you press the
SETUP button.
• The SETUP button can function even during normal
playback, however some operations may be inaccessible,
and a message will appear. In this case, try again after
playback is stopped.
Setting
LANGUAGE
PICTURE
DISPLAY
OPERATION
Page
On-Screen Language
DVD
VCD
CD
To select a preferred language for on-screen
displays.
36
Disc Menu Language
DVD
To select a preferred language for disc menus.
36
Audio Language
DVD
To select a preferred language for the sound
track.
36
Subtitle Language
DVD
To select a preferred language for subtitles.
36
TV Shape
DVD
To select a picture size according to the aspect
ratio of your TV.
37
Blacker than Black
DVD
VCD
To make an adjustment of the black level on
your TV using a commercially available test disc
that contains adjustment signals.
38
Black Level
DVD
VCD
To select the black level of playback pictures.
38
Progressive 4:3 Output
DVD
To select the video output for pictures recorded
in the 4:3 picture size. (Only when a TV is
connected to the COMPONENT VIDEO
connector.)
38
Component Video
DVD
To select the signal output format. (Only when a
TV is connected to the COMPONENT VIDEO
connector.)
38
Audio Out Select
DVD
VCD
CD
To select an output sound format corresponding
to your system connection.
39
Dynamic Range Control
DVD
To turn on or off a function that makes faint
sounds easier to hear even if you lower the
volume during late hours playback.
39
Karaoke Vocal
DVD
To turn on or off the vocal output during DVD
KARAOKE disc playback.
39
Extended Audio Features
DVD
To turn on or off a special language for visually
impaired persons.
39
On-Screen Displays
DVD
VCD
CD
To turn on or de-activate the operational status
display on the screen.
40
OSD Background Color
DVD
VCD
CD
To select the background color for on-screen
displays.
40
Extended Subtitle Features
DVD
To turn on or off special subtitles for hearing
impaired persons.
40
Screen Saver
DVD
To turn the screen saver on or off.
40
Pause/Still
DVD
To select the resolution of still pictures.
(Field/Frame)
40
Parental Lock
DVD
To turn the parental lock function on or off.
40
Title Stop
DVD
To turn on or off a feature that automatically
stops playback after a title has been viewed.
41
PBC
VCD
To use the menu when playing a PBC-featured
VIDEO CD.
41
Function setup
AUDIO
Details
35
Function setup
Customizing the Function Settings (continued)
Setting details
Audio Language
PICTURE
LANGUAGE
LANGUAGE
On-Screen Language
Disc Menu Language
Audio Language
Subtitle Language
On-Screen Language
DVD
AUDIO
DISPLAY
English:
French:
Spanish:
Others:
ENG
ENG
ENG
–––
VCD
CD
English: To view on-screen displays in English.
French: To view on-screen displays in French.
Spanish: To view on-screen displays in Spanish.
Disc Menu Language
English:
French:
Spanish:
Others:
To play sound tracks in English.
To play sound tracks in French.
To play sound tracks in Spanish.
To make a further choice.
After pressing the ENTER button, follow
steps 1) - 4) below.
1) Obtain the abbreviation of the preferred
language from the list 42 .
2) Select the first character by pressing the /
buttons.
3) Press the / buttons to shift and select the
second character by pressing the /
buttons.
DVD
PICTURE
LANGUAGE
On-Screen Language
Disc Menu Language
Audio Language
Subtitle Language
To display disc menus in English.
To display disc menus in French.
To display disc menus in Spanish.
To make a further choice.
After pressing the ENTER button, follow
steps 1) - 4) below.
1) Obtain the abbreviation of the preferred
language from the list 42 .
2) Select the first character by pressing the /
buttons.
3) Press the / buttons to shift and select the
second character by pressing the / buttons.
PICTURE
LANGUAGE
On-Screen Language
Disc Menu Language
Audio Language
Subtitle Language
AUDIO
ENG
PA
ENG
–––
DISPLAY
AUDIO
ENG
ENG
PA
–––
DISPLAY
OPERATION
English
French
Spanish
Others
Code
PA
4) Press the ENTER button.
Note
Some DVD video discs may be played in a different
language than you selected. A prior language may be
programmed on the disc.
OPERATION
Subtitle Language
English
French
Spanish
Others
Code
PA
4) Press the ENTER button.
Note
Some DVD video discs may not include your preselected language. In this case, the DVD video player
automatically displays disc menus consistent with the
disc’s initial language setting.
36
DVD
OPERATION
English:
French:
Spanish:
No Subtitle:
Others:
DVD
To display subtitles in English.
To display subtitles in French.
To display subtitles in Spanish.
To disable subtitles.
To make a further choice.
After pressing the ENTER button, follow
steps 1) - 4) below.
1) Obtain the abbreviation of the preferred
language from the list 42 .
2) Select the first character by pressing the
buttons.
/
3) Press the / buttons to shift and select the
second character by pressing the /
buttons.
LANGUAGE
PICTURE
TV Shape
Blacker than Black
Black Level
Progressive 4:3 Output
Component Video
PICTURE
PICTURE
LANGUAGE
On-Screen Language
Disc Menu Language
Audio Language
Subtitle Language
AUDIO
ENG
ENG
ENG
PA
DISPLAY
OPERATION
AUDIO
DISPLAY
OPERATION
LCD
Off
NRML
On
Y CB CR
English
French
Spanish
No Subtitle
Others
PA
TV Shape
4:3 Letterbox:
Select when a standard 4:3 TV is
connected.
Displays theatrical images with
masking bars above and below the
picture.
4:3 Normal:
Select when a standard 4:3 TV is
connected.
Displays pictures cropped to fill
your TV screen. Either or both
sides of the picture are cut off.
4) Press the ENTER button.
Notes
• Some DVD video discs may be set to display subtitles
in a different language than you selected. A prior
subtitle language may be programmed on the disc.
• Some DVD video discs allow you to change subtitle
selections only via the disc menu. If this is the case,
press the MENU button and choose the appropriate
subtitle language from the selection on the disc menu.
DVD
Function setup
Code
16:9 Widescreen: Select when a 16:9 wide TV is
connected.
16:9LCD:
Select when you use the LCD of
this player.
Displays pictures in the same size
(4:3, 16:9, etc.) as recorded in a
DVD video disc.
Notes
• The displayable picture size is preset on the DVD video
disc. Therefore, the playback picture of some DVD
video discs may not conform to the picture size you
select.
• When you play DVD video discs recorded in the 4:3
picture size only, the playback picture always appears
in the 4:3 picture area regardless of the TV shape
setting.
• If you select “16:9 Widescreen” or “16:9LCD” and you
own a 4:3 TV set, the DVD playback picture will be
horizontally distorted during playback. Images will
appear to be horizontally compressed. Always be sure
that your TV shape conforms to the actual TV in use.
• When you view pictures on the LCD of this player,
select “16:9LCD”.
37
Function setup
Customizing the Function Settings (continued)
Setting details
(Continued)
Component Video
Blacker than Black
DVD
VCD
Off: For normal use.
On: Select when you adjust the black level of your
TV using a commercially available test disc that
contains adjustment signals.
Black Level
DVD
VCD
Select the brightness of playback pictures you view
on a TV which is connected to the AV OUT jack or the
S VIDEO jack of this player.
Enhanced: Expanded black level.
Normal:
Standard black level.
Progressive 4:3 Output
DVD
VCD
Make this selection when you connect the player
using the COMPONENT VIDEO connector to a TV
equipped with the component video inputs which
does not have aspect ratio control.
Off: When you play pictures of DVD video discs or
VIDEO CDs recorded in the 4:3 picture size, the
COMPONENT VIDEO connector does not
output them to the connected TV. To view them,
connect the TV to the S VIDEO jack or the AV
OUT jack of the player.
On: The COMPONENT VIDEO connector always
outputs playback pictures to the connected TV.
When you play pictures of DVD video discs or
VIDEO CDs recorded in the 4:3 picture size,
they will be horizontally stretched. To view them
in the original 4:3 size, select “Off” and connect
the TV to the S VIDEO jack or the AV OUT jack
of the player.
38
DVD
VCD
Select the output signal format corresponding to the
scanning system (interlace or progressive) of the
connected TV equipped with the component video
inputs, or the color system of the monitor.
Y CB CR: Select when connected to a TV (interlace
system) equipped with the component
video inputs using the COMPONENT
VIDEO connector.
Y PB PR: Select when connected to a TV
(progressive system) equipped with the
component video inputs using the
COMPONENT VIDEO connector.
Karaoke Vocal
LANGUAGE
AUDIO
DISPLAY
PICTURE
AUDIO
Audio Out Select
Dynamic Range Control
Karaoke Vocal
Extended Audio Features
DVD
VCD
Bitstream
On
Off
Off
CD
Select the output sound format corresponding to your
system connection.
For details of sound recording systems, see 31 .
Bitstream:
Select when connected to an amplifier
equipped with a Dolby Digital, DTS,
MPEG1 or MPEG2 decoder. 48 49
The player outputs digital audio
information in the bitstream format
when you play a DVD video disc
recorded on the Dolby Digital, DTS,
MPEG1 or MPEG2 recording system.
Off: The primary vocal is not output.
On: The primary vocal is output when it is recorded
on the disc.
Notes
• The vocal output feature is used during playback of
Dolby Digital (multi-channel) recorded DVD KARAOKE
discs. This feature allows you to turn off vocal audio
tracks, or restore them for background
accompaniment.
• When playing KARAOKE, connect appropriate audio
equipment such as an amplifier to the player.
Extended Audio Features
Function setup
Audio Out Select
DVD
OPERATION
DVD
Some DVD video discs contain a special language
track that describes the actions on-screen for visually
impaired persons. The player automatically plays this
special feature.
Off: This function does not work.
On: This function works.
Analog 2ch: Select when connected to a TV, or
Dolby Pro Logic or stereo system via
the analog audio jacks. 47 48
PCM:
Select when connected to a 2 channel
digital stereo amplifier. 49
The player outputs sounds in the PCM
2ch format when you play a DVD video
disc recorded on the Dolby Digital,
MPEG1 or MPEG2 recording system.
Dynamic Range Control
DVD
Turn on or off a function that makes faint sounds
easier to hear. Especially beneficial, if you lower the
volume during late hours playback.
Off: Full dynamic range is maintained.
On: Dynamic range is reduced.
Notes
• This function works only during playback of Dolby
Digital recorded discs.
• The level of Dynamic Range Reduction may differ
depending on the DVD video disc.
39
Function setup
Customizing the Function Settings (continued)
Setting details
LANGUAGE
DISPLAY
PICTURE
On-Screen Displays
DVD
On
Blue
Off
On
VCD
Off: Operational modes (e.g. “Play”, “
displayed.
On: Operational modes (e.g. “Play”, “
displayed on-screen.
OSD Background Color
OPERATION
AUDIO
DISPLAY
On-Screen Displays
OSD Background Color
Extended Subtitle Features
Screen Saver
DVD
OPERATION
Pause/Still
CD
”) are not
”) are
VCD
Screen Saver
Auto
Off
Off
On
Auto:
For normal use. Still and fast motion images
can be paused.
Frame: The resolution of still pictures is improved,
so that you can make a motionless picture
sharper when you pause it.
DVD
DVD
DVD video discs equipped with the parental lock
function are rated according to their content. The
contents allowed by a parental lock level and the way
a DVD video disc can be controlled may vary from
disc to disc. For example, if the disc allowed you
could edit out violent scenes unsuitable for children
and replace them with more suitable scenes, or lock
out playback of the disc altogether.
• DVD video discs may or may not respond to the
parental lock settings. This is not a defect in the player.
Make sure this function works with your DVD video
discs.
DVD
Off: The screen saver is disengaged.
On: The screen saver operates.
Off: The parental lock feature does not function.
After pressing the ENTER button, follow step 1)
below.
On: To activate the parental lock feature or change
the settings.
After pressing the ENTER button, follow steps
1) - 3) below.
LANGUAGE
OPERATION
Pause/Still
Parental Lock
Title Stop
PBC
40
DISPLAY
AUDIO
DVD
Parental Lock
Some DVD video discs contain special subtitles, an
enhancement of closed captioning for hearing
impaired persons. The player automatically displays
these special subtitles.
Off: This function does not work.
On: This function works.
PICTURE
CD
Blue: Blue background.
Gray: Gray background.
Extended Subtittle Features
LANGUAGE
OPERATION
Pause/Still
Parental Lock
Title Stop
PBC
PICTURE
DISPLAY
AUDIO
Auto
Off
Off
On
Off
On
Security Code
1) Press the number buttons to create a personal
4-digit security code, then press ENTER.
If you make a mistake before pressing the
ENTER button, press the CLEAR button and
enter your 4-digit security code again.
2) Press the / buttons to select the country
whose standards were used to rate the DVD
video disc.
Level 8
Level 7
Level 6
Level 5
Level 4
Level 3
Level 2
Level 1
3) Press the / buttons to select the parental
lock level, then press the ENTER button.
STOP
STOP
STOP
STOP
ENTER
The 4-digit security code is cleared.
2) Press the number buttons to create a new
4-digit security code.
3) Press the ENTER button.
Title Stop
Function setup
CANADA
Viewable
To change your 4-digit security code
1) After selecting “On” or “Off,” press the STOP
button four times, then press the ENTER
button.
DVD
Off: The player continues after playback of a title is
completed.
On: The player stops after playback of a title is
completed.
CANADA
Locked
Viewable
Level8
Level 7
Level 6
Level 5
Level 4
Level 3
Level 2
Level 1
PBC
VCD
Off: When playing a VIDEO CD without using the
menu.
On: To use the menu when playing a PBC-featured
VIDEO CD.
You cannot play DVD video discs rated higher than
the level you selected unless you cancel the parental
lock function.
For example, when you select level 7, discs rated
higher than level 7 are locked out and cannot be
played.
The parental lock level is equivalent to the following
USA movie ratings.
Level 7: NC-17
Level 6: R
Level 4: PG 13
Level 3: PG
Level 1: G
The parental lock levels for “CANADA” are included
for future use. Check the appropriate parental lock
level when you buy a DVD video disc equipped with
the parental lock feature in the future.
To change the parental lock level
Follow steps 1) - 3).
41
Function setup
Table of Languages
Table of languages and their abbreviations
Abbreviation
–––
CHI (ZH)
DUT (NL)
ENG (EN)
FRE (FR)
GER (DE)
ITA (IT)
JPN (JA)
KOR (KO)
MAY (MS)
SPA (ES)
AA
AB
AF
AM
AR
AS
AY
AZ
BA
BE
BG
BH
BI
BN
BO
BR
CA
CO
CS
CY
DA
DZ
EL
EO
ET
EU
FA
FI
FJ
FO
FY
GA
GD
GL
42
Language
No alternate
language
Chinese
Dutch
English
French
German
Italian
Japanese
Korean
Malay
Spanish
Afar
Abkhazian
Afrikaans
Amharic
Arabic
Assamese
Aymara
Azerbaijani
Bashkir
Belorussian
Bulgarian
Bihari
Bislama
Bengali, Bangla
Tibetan
Breton
Catalan
Corsican
Czech
Welsh
Danish
Bhutani
Greek
Esperanto
Estonian
Basque
Persian
Finnish
Fiji
Faroese
Frisian
Irish
Scottish Gaelic
Galician
Abbreviation
GN
GU
HA
HI
HR
HU
HY
IA
IE
IK
IN
IS
IW
JI
JW
KA
KK
KL
KM
KN
KS
KU
KY
LA
LN
LO
LT
LV
MG
MI
MK
ML
MN
MO
MR
MT
MY
NA
NE
NO
OC
OM
OR
PA
PL
PS
Language
Guarani
Gujarati
Hausa
Hindi
Croatian
Hungarian
Armenian
Interlingua
Interlingue
Inupiak
Indonesian
Icelandic
Hebrew
Yiddish
Javanese
Georgian
Kazakh
Greenlandic
Cambodian
Kannada
Kashmiri
Kurdish
Kirghiz
Latin
Lingala
Laotian
Lithuanian
Latvian, Lettish
Malagasy
Maori
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Maltese
Burmese
Nauru
Nepali
Norwegian
Occitan
(Afan) Oromo
Oriya
Panjabi
Polish
Pashto, Pushto
Abbreviation
PT
QU
RM
RN
RO
RU
RW
SA
SD
SG
SH
SI
SK
SL
SM
SN
SO
SQ
SR
SS
ST
SU
SV
SW
TA
TE
TG
TH
TI
TK
TL
TN
TO
TR
TS
TT
TW
UK
UR
UZ
VI
VO
WO
XH
YO
ZU
Language
Portuguese
Quechua
Rhaeto-Romance
Kirundi
Rumanian
Russian
Kinyarwanda
Sanskrit
Sindhi
Sango
Serbo-Croatian
Singhalese
Slovak
Slovenian
Samoan
Shona
Somali
Albanian
Serbian
Siswati
Sesotho
Sundanese
Swedish
Swahili
Tamil
Telugu
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Setswana
Tongan
Turkish
Tsonga
Tatar
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapük
Wolof
Xhosa
Yoruba
Zulu
Connections
Read this chapter first to make the necessary
preparations.
Power Connection
Connecting to a TV
Connecting to Optional
Equipment
Connecting to a PC
Connections
Power Connection
Connect the supplied AC adapter to power the player.
For outdoor use, the battery pack (supplied) is also available.
When using the battery pack, follow the instructions on page 45 .
Caution
• Do not connect the power plug to a power outlet other than that indicated on the label, as this can result in a risk of fire
or electric shock.
• Do not connect or disconnect the power plug with wet hands. Doing so may cause electric shock.
• Do not use an AC adapter other than one specified, as it can cause a fire or damage to the player.
DC IN 15V
PC
To the DC inlet
2
Follow steps 1 to 3 to connect.
When disconnecting, reverse the order.
AC adapter
1
Connect the supplied AC adapter
and the power cord firmly.
To wall outlet
3
Power cord
Power plug
44
Warning
• Do not use a battery pack other than one specified as it can result in a fire or damage to the unit.
• Do not heat, open, or short-circuit the battery pack. Do not throw the battery pack into a fire. Doing so may cause an
explosion or a fire.
• Make sure that the battery pack is attached firmly to the player when using it.
Using the battery pack
Use a battery pack MEDB01AX (supplied). Charge it before using.
Attaching the battery pack
Detaching the battery pack
First disconnect the AC adapter and the power cord
from the player, then attach the battery pack.
1 Disconnect the AC adapter and the power cord
from the player.
1 Open the connector cover on the bottom of the
player.
2 Detach the battery pack while pressing the
release button.
2 Insert the hooks of the battery pack into the
holes on the rear of the player.
Release button
3 Slide the battery pack up until the hooks click.
Connections
Rear of the player
Hook
Connector
cover
Hook
Battery pack (supplied)
Note
Do not detach the battery pack while you are operating the
player (while the POWER/CHG indicator illuminates in green).
LCD brightness while using the battery pack
Charging the battery pack
1 Attach the battery pack to the player.
2 Connect the supplied AC adapter and the power
cord to the player. 44
Charging starts, and the POWER/CHG indicator
illuminates in orange.
When the charging is completed, the POWER/CHG
indicator turns off.
Charging time is approximately 3.5 hours. The player
will operate for about 2.5 hours at normal
temperature if powered by a charged brand-new
battery pack. Charging time and life of a battery pack
vary depending on environmental conditions and
operational status. Low temperature will extend the
charging time and shorten the life.
Since the player operates in a power saving mode when
attached the battery pack, the LCD brightness may be
reduced. It can be restored by pressing the DIMMER
button on the remote control, however in this case,
battery pack life will be shortened.
Note on the top cover while using the battery
pack
Be careful when opening the top cover to its full extent
when using the player with the battery pack, as the top
cover may knock against the battery pack, causing
serious damage to the player.
S VIDEO
VOLUME
/ REMOTE
AV IN
BITSTREAM/PCM
AV OUT
COMPONENT VIDEO
Notes
• The attached battery pack may get warm when you are
charging it or operating the player. This is not a defect.
• The POWER/CHG indicator flashes in green when the
power in the battery pack is running out.
45
Connections
Caution
When you use headphones, keep the volume at a
moderate level. If you use the headphones continuously
with high volume sound, it may cause hearing damage.
Connecting to a TV
Connect the player to a TV to view playback pictures.
For details of output sound, see 31 .
Connecting headphones
Connect headphones to the headphone jack
using a stereo mini plug.
Before connecting, temporarily turn down the
volume with the headphone volume control.
Readjust to your preference when playback
starts.
Signal flow
Audio/video cable
(supplied)
• Turn off the player before you connect or
disconnect the headphone cable. Neglecting this
may cause abnormal performance of the player.
S video cable
(Not supplied)
To
VOLUME
(headphone) jack
To S VIDEO
To AV OUT
S VIDEO
/ REMOTE
AV IN
BITSTREAM/PCM
AV OUT
To AV IN
To COMPONENT VIDEO
Component video cable
(supplied)
Audio/video cable
You can use the LCD of this player to monitor pictures of video equipment connected
via the AV IN jack.
To audio output (red)
To audio output (white)
Video equipment
To video output (yellow)
Notes
• While the AV IN jack is connected, the player does not play discs.
• While you are using the LCD of the player to view pictures of video equipment, the
automatic power off function 17 does not work.
Notes
• Refer to the owner’s manual of the connected TV (or other equipment) as well.
• When you connect the player to your TV, be sure to turn off the power and unplug both units from the wall outlet before
making any connections.
• Connect the player directly to your TV. If you connect the player to a VCR, TV/VCR combination or video selector, the
playback picture may be distorted as DVD video discs are copy protected.
• If you place the player near a tuner or radio, the radio broadcast sound might be distorted. In this case, place the player
away from the tuner and radio.
• The output sound of the player has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate listening
level. Otherwise, the speakers may be damaged by a sudden high volume sound.
46
TV
To audio input (red)
To audio input (white)
Set “Audio Out Select” to “Analog 2ch.”
To video input (yellow)
34
39
To S video input
To Y (Y)
To PB (CB)
or
To component
video inputs
To PR (CR)
Set “Component Video” to “Y CB CR”
or “Y PB PR”, according to the
scanning system (interlace or
progressive) of your TV. 38
Connections
TV equipped with
component video inputs
(interlace, progressive)
Note
Pictures cannot be viewed if you are using
the player with the battery pack. Use the
AC adapter.
You can enjoy playback sounds on your audio system by connecting the
AV OUT jack or BITSTREAM/PCM jack on the player to the audio inputs
on your audio equipment.
For the connection to audio equipment, see 48 .
Using the S video cable
If the TV has an S video input, connect the player with
the supplied S video cable for better quality playback
picture.
The S video cable transmits video signals only. To
obtain sound output, be sure to connect the red and
white plugs of the supplied audio/video cable to your
TV’s audio inputs.
When using the S video cable, do not connect the
yellow video cable.
PROGRESSIVE outputs/inputs (ColorStream®Pro)
Some TVs or monitors are equipped with component video
inputs that are capable of reproducing a progressively
scanned video signal. Connecting to these inputs allows you
to view the highest quality pictures with less flicker.
INTERLACED outputs/inputs (ColorStream®)
Some TVs or monitors are equipped with component video
inputs. Connecting to these inputs allows you to enjoy higher
quality picture playback.
Actual labels for component video inputs may vary depending
on the TV manufacturer. (ex. Y, R-Y, B-Y or Y, CB, CR)
In some TVs or monitors, the color levels of the playback
picture may be reduced slightly or the tint may change. In
such a case, adjust the TV or monitor for optimum
performance.
47
Connections
Connecting to Optional Equipment
You can enjoy high quality dynamic sounds by connecting the player to optional
audio equipment.
For connection to your TV, see “Connecting to a TV” 46 47 .
For details of output sound, see 31 .
: Front speaker
: Rear speaker
: Sub woofer
: Center speaker
: Signal flow
Connecting to an amplifier equipped with a Dolby Digital decoder
Dolby Digital
Manufactured under license from Dolby
Dolby Digital is the surround sound technology used in theaters showing the latest movies,
Laboratories. “Dolby” and the double-D
and is now available to reproduce this realistic effect in the home. You can enjoy motion
symbol are trademarks of Dolby
picture and live concert DVD video discs with this dynamic realistic sound by connecting the
Laboratories. Confidential unpublished
player to a 6 channel amplifier equipped with a Dolby Digital decoder or Dolby Digital
works. ©1992-1997 Dolby Laboratories.
processor. If you have a Dolby Pro Logic Surround decoder, you will obtain the full benefit of
All rights reserved.
Pro Logic from the same DVD movies that provide full 5.1-channel Dolby Digital
soundtracks, as well as from titles with the Dolby Surround mark.
• Use DVD video discs encoded via
Amplifier equipped with a
Dolby Digital decoder
To digital audio input
(coaxial)
VOLUME
/ REMOTE
AV IN
BITSTREAM/PCM
the Dolby Digital recording
system.
• Make the following setting.
AV OUT
To BITSTREAM/PCM
75Ω coaxial cable
(not supplied)
Digital cable (supplied)
On-screen display
Select:
“Audio Out Select”
“Bitstream”
Recording system
Page
34
39
31
D
Connecting to an amplifier equipped with Dolby Pro Logic Surround
Dolby Pro Logic Surround
You can enjoy the dynamic realistic sound of Dolby Pro Logic Surround by connecting an amplifier and speaker system (right and left
front speakers, a center speaker, and one or two rear speakers).
With an amplifier equipped with Dolby Digital
Connect the equipment the same way as described in “Connecting to an amplifier
equipped with a Dolby Digital decoder.” Refer to that amplifier’s owner’s manual and set
the amplifier so you can enjoy Dolby Pro Logic Surround sound.
With an amplifier not equipped with Dolby Digital
Connect the equipment as follows.
*
Amplifier equipped with
Dolby Pro Logic Surround
VOLUME
/ REMOTE
AV IN
BITSTREAM/PCM
On-screen display
Select:
“Audio Out Select”
“Analog 2ch”
Page
34
39
AV OUT
Be sure to set “Audio Out Select”
to “Analog 2ch” when you enjoy
sounds of Dolby Pro Logic
Surround using this connection.
To AV OUT
To analog audio input
• Make the following setting.
Audio/video cable (supplied)
(yellow)
No need to connect when using an S
video cable to connect to your TV.
* Connect one or two rear speakers.
The output sound from the rear speakers will be
monaural even if you connect two rear speakers.
Connecting to an amplifier equipped with a DTS decoder
Digital Theater Systems (DTS)
“DTS” and “DTS Digital Surround” are
DTS is a high quality surround technology used in theaters and now available for home use,
trademarks of Digital Theater Systems,
on DVD video discs or audio CDs.
Inc.
If you have a DTS decoder or processor, you can obtain the full benefit of 5.1 channel DTS
•
Use DVD video discs or audio
encoded sound tracks on DVD video discs or audio CDs.
Amplifier equipped with a
DTS decoder
To digital audio input
(coaxial)
48
75Ω coaxial cable
(not supplied)
VOLUME
/ REMOTE
AV IN
BITSTREAM/PCM
AV OUT
To BITSTREAM/PCM
Digital cable (supplied)
CDs encoded via the DTS
recording system.
• Make the following setting.
On-screen display
Select:
“Audio Out Select”
“Bitstream”
Recording system
DTS
Page
34
39
31
Warning
• When you are connecting (via the BITSTREAM/PCM jack) an AV decoder that does not have the Dolby Digital, Digital
Theater Systems (DTS) or MPEG2 decoding function, be sure to set “Audio Out Select” to “PCM” from the on-screen
displays 34 39 . Otherwise, high volume sound may damage your hearing as well as the speakers.
• When playing DTS-encoded discs (DVD video discs and audio CDs), excessive noise may be output from the analog
stereo jacks. To avoid possible damage to the audio system, you should take proper precautions when the AV OUT jack
of the player is connected to an amplification system. To enjoy DTS Digital Surround™ playback, an external 5.1
channel DTS Digital Surround™ decoder system must be connected to the BITSTREAM/PCM jack of the player.
Connecting to an amplifier equipped with an MPEG2 audio decoder
MPEG2 sound
You can enjoy motion picture and live concert DVD video discs with dynamic
realistic sound by connecting an amplifier equipped with an MPEG2 audio decoder
or MPEG2 audio processor.
Amplifier equipped with an
MPEG2 audio decoder
To digital audio input
(coaxial)
VOLUME
/ REMOTE
AV IN
BITSTREAM/PCM
AV OUT
To BITSTREAM/PCM
Digital cable (supplied)
On-screen display
Select:
“Audio Out Select”
“Bitstream”
Recording system
MPEG
Page
34
39
31
Connections
75Ω coaxial cable
(not supplied)
• Use DVD video discs encoded via
the MPEG2 recording system.
• Make the following setting.
Connecting to an amplifier equipped with a digital audio input
2 channel digital stereo
You can enjoy the dynamic sound of 2 channel digital stereo by connecting an
amplifier equipped with a digital audio input and speaker system (right and left front
speakers).
Amplifier equipped with a
digital audio input
To digital audio input
(coaxial)
75Ω coaxial cable
(not supplied)
VOLUME
/ REMOTE
AV IN
BITSTREAM/PCM
AV OUT
To BITSTREAM/PCM
• Make the following setting.
On-screen display
Select:
“Audio Out Select”
“PCM”
Page
34
39
Digital cable (supplied)
Notes
• DO NOT connect the BITSTREAM/PCM jack of the player to the AC-3 RF input of a Dolby Digital Receiver. This input on
your A/V Receiver is reserved for Laserdisc use only and is incompatible with the BITSTREAM/PCM jack of the player.
• Connect the BITSTREAM/PCM jack of the player to the “COAXIAL” input of a Receiver or Processor.
• Refer to the owner’s manual of the connected equipment as well.
• When you connect the player to other equipment, be sure to turn off the power and unplug all of the equipment from the wall
outlet before making any connections.
• The output sound of the player has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate listening
level. Otherwise, the speakers may be damaged by a sudden high volume sound.
• Turn off the amplifier before you connect or disconnect the player’s power cord. If you leave the amplifier power on, the
speakers may be damaged.
49
Connections
Connecting to a PC
This player can be connected to a PC using an ATAPI card (option: MEDC01AX).
By connecting to a PC, you can use this player as a 4 times speed DVD-ROM
drive or a 24 times speed CD-ROM drive.
When connected to a PC using an ATAPI card, the player operates as a DVD-ROM/CD-ROM drive
exclusively.
When you do not use this player as a DVD-ROM/CD-ROM drive, disconnect the connection cable from the
PC connector. As long as it is connected the cable, the player will not function as a video player.
An ATAPI card (option) is necessary for connection to a PC.
For details, refer to the instruction supplied with the ATAPI card.
DC IN 15V
Open the cover.
2
1
To PC connector
4
To a PC
1
2
3
4
Connect the connection cable of the ATAPI card to the player.
Connect the supplied AC adapter to the player.
44
Follow steps 1 to 4 on page 14.
Connect the ATAPI card to a PC.
Notes
• While you are using the player as a DVD-ROM/CD-ROM drive, audio signals (including those from the headphone jack) are
not output.
• While you are using the player as a DVD-ROM/CD-ROM drive, no picture is displayed on the LCD.
• Some PC systems may require software to play DVD video disc and VIDEO CDs.
50
Others
Before Calling Service
Personnel
Specifications
Identification of Controls
LIMITED WARRANTY
PORTABLE DVD PLAYER
Others
Before Calling Service Personnel
Check the following guide for the possible cause of a problem before contacting service.
Symptoms and correction
Symptom
Cause
Correction
No power.
• The AC adapter or power plug is
disconnected.
• Connect the AC adapter or power plug
securely.
44
45
Page
• Dead batteries.
• Re-charge the battery.
The player turned off by itself.
• The automatic power off function turned
the unit off.
• Press the
No picture.
• The TV is not set to receive DVD signal
output.
• Select the appropriate video input mode
on the TV so the picture from the player
appears on the TV screen.
14
• The audio/video cable is not connected
securely.
• Connect the audio/video cable securely
into the appropriate jacks.
46, 47
• The equipment connected with the audio/
video cable is not set to receive DVD
signal output.
• Select the correct input mode of the
audio receiver so you can listen to the
sound from the player.
• The audio/video cable is not connected
securely.
• Connect the audio/video cable securely
into the appropriate jacks.
46, 47
48, 49
• The audio receiver or TV is turned off.
• Turn on the equipment connected with
the audio/video cable.
46, 47
48, 49
• The setting of output sound format is
incorrect.
• Select the proper audio setting.
31, 34
39
• The disc is dirty.
• Eject the disc and clean it.
• It is in fast forward or fast reverse
playback.
• Sometimes a small amount of picture
distortion may appear. This is not a
malfunction.
–
• The main unit was moved or given a
shock.
• Vibrating or shaking the unit during
playback may produce distortion. This is
not a malfunction. If not restored to usual
status, stop the playback and start again.
–
No sound.
The playback picture has
occasional distortion.
(PLAY) button.
17
47
10
• The disc is not set firmly.
• Remove the disc and set it again.
14
Brightness is unstable or
noises are present in the
playback pictures.
• The effect of copy protection.
• Connect the player directly to the TV.
Avoid connecting the player to a VCR or
TV/VCR combination.
46
The player does not start
playback.
• No disc is inserted.
• Insert a disc.
14
• An unplayable disc is inserted.
• Insert a playable disc. (Check the disc
type and color system.)
11
• The disc is inserted upside down.
• Insert the disc with the playback side
down.
14
• The disc is not inserted securely.
• Insert the disc securely in the disc holder.
14
• The disc is dirty.
• Clean the disc.
10
• The parental lock function is set.
• Cancel the parental lock function or
change the parental lock level.
40
Playback does not follow the
course of the disc’s program.
• It is in the mode of repeat playback,
memory playback, etc.
• These operations may prevent a proper
progression of the contents.
–
Buttons do not work.
• Power supply fluctuations or other
abnormalities such as static electricity may
interrupt correct operations.
• Turn the power on or off with the
POWER button. Or disconnect the power
plug and insert it into the wall outlet
again.
–
• The buttons are locked.
• Release the buttons.
17
• The remote control is not pointed at the
remote sensor of the player.
• Point the remote control at the remote
sensor of the player.
57
• The remote control is too far from the
player.
• Operate the remote control within about
7 m.
57
• The batteries in the remote control are
exhausted.
• Replace the batteries with new ones.
57
The remote control does not
work properly.
52
Specifications
Player / Connectors / Liquid crystal display / Supplied accessories
Player
Power supply
DC 15 V (Rated current : 2 A)
120 V AC, 60 Hz (with the supplied AC adapter)
Mass
680 g
External dimensions
139 × 32 × 149 mm (W/H/D)
Signal system
Standard NTSC
Laser
Semiconductor laser, wavelength 650 nm / 795 nm
Frequency range
DVD linear sound : 48 kHz sampling 4 Hz to 22 kHz
96 kHz sampling 4 Hz to 44 kHz
Operating conditions
Temperature: 5 °C to 35 °C, Operation status: Horizontal
Connectors
1.0 V (p-p), 75 Ω, negative sync., Ø3.5mm mini jack × 1
S video output (S VIDEO)
(Y) 1.0 V (p-p), 75 Ω, negative sync., Mini DIN 4-pin × 1
(C) 0.286 V (p-p), 75 Ω
Component video output
(COMPONENT VIDEO)
D connector 14-pin, 2 lines, 1.27 mm pitch
(Y): 1.0 V (p-p), 75 Ω, (PB/CB • PR/CR): 0.7 V (p-p), 75 Ω
Audio output (BITSTREAM/PCM)
Optical/coaxial connector (Ø3.5mm) × 1
Audio output (AV OUT)
2.0 V (rms), 220 Ω, Ø3.5mm mini jack × 1
Video input (AV IN)
1.0 V (p-p), 75 Ω, negative sync., Ø3.5mm mini jack × 1
Audio input (AV IN)
2.0 V (rms), Ø3.5mm mini jack × 1
Headphone terminal
Ø3.5mm stereo mini jack × 1
Others
Video output (AV OUT)
Liquid crystal display
Panel size
5.8 inches (76.32 mm × 127.2 mm)
Projection system
TN color transmission
Driving system
TFT active matrix
Resolution
800 × 480 (effective pixel rate : more than 99.99%)
Supplied accessories
Audio/video cable ................................................. 1
Remote control (MEDR02UX) .............................. 1
Batteries (AA) ....................................................... 2
AC adapter (PA2501U) ......................................... 1
Battery pack (MEDB01AX) ................................... 1
Headphones ......................................................... 1
Digital cable .......................................................... 1
Component video cable ........................................ 1
Power cord ........................................................... 1
• Designs and specifications are subject to change without notice.
53
Others
Identification of Controls
See the page in
for details.
Main unit
Press this button to
open the top cover.
LCD 15 17
Speakers
POWER/CHG (Power/Charge)
indicator 14 44 45
RETURN button 17 34
ENTER button 34
(Eject) button 14
TOP MENU button 20
MENU button 15
Direction buttons (
POWER ON /
/
(Play) button 14 15
(Pause) button 16
POWER OFF /
54
/
(Stop) button 16
/
) 34
Side view
VOLUME
S VIDEO
/ REMOTE
AV IN
BITSTREAM/PCM
AV OUT
COMPONENT VIDEO
Volume control 14 46
S VIDEO jack 46
Headphone jack 46
COMPONENT VIDEO connector 46
Do not connect anything.
AV OUT jack 46
AV IN jack 46
BITSTREAM/PCM jack 48 49
Others
DC IN 15V
PC
DC inlet 44
PC card connector 50
55
Others
Identification of Controls (continued)
The instructions in this manual describe the functions of the remote control. See the page in
for details.
Remote control
POWER button 14
OPEN button 14
OPEN
DIMMER
POWER
ZOOM
3D
SETUP button 34
SETUP
DISPLAY button 32
DISPLAY
DIMMER button 15
3D button 28
ANGLE SUBTITLE AUDIO DISC/MEMO
ANGLE button 29
ZOOM button 28
DISC/MEMO button 24
SUBTITLE button 30
Number buttons 20
1
2
3
4
5
6
7
8
9
0
+10
T
TOP MENU
MENU
AUDIO button 31
T button 20
ENTER button 34
TOP MENU button 20
Direction buttons 34
( / / / )
CLEAR button 20
MENU button*
ENTER
CLEAR
RETURN
RETURN button 34
REV
PLAY
FWD PAUSE/STEP
REV button 18
PLAY button 15
SKIP button 21
PAUSE/STEP button 16 18
SKIP
STOP
SKIP
SLOW
RANDOM MEMORY REPEAT A-B RPT
FWD button 18
SLOW button 19
STOP button 16
SKIP button 21
RANDOM button 27
A-B RPT button 25
MEMORY button 26
REPEAT button 25
* MENU button
Use the MENU button to display the menu included on
many DVD video discs. To operate a menu, follow the
instructions in “Locating a title using the top menu.”
20
56
Loading batteries
1
Open the cover.
Operating with the remote control
Point the remote control at the remote
sensor and press the buttons.
OFF
POWER/CHG
30°
2
Insert batteries (AA size).
3
Close the cover.
Notes on batteries
Improper use of batteries may cause battery leakage and
corrosion. To operate the remote control correctly, follow the
instructions below.
• Do not insert batteries into the remote control in the wrong
direction.
• Do not charge, heat, open, or short-circuit the batteries.
Do not throw batteries into a fire.
• Do not leave dead or exhausted batteries in the remote
control.
• Do not use different types of batteries together, or mix old
and new batteries.
• If you do not use the remote control for a long period of
time, remove the batteries to avoid possible damage from
battery corrosion.
• If the remote control does not function correctly or if the
operating range becomes reduced, replace all batteries
with new ones.
• If battery leakage occurs, wipe the battery liquid from the
battery compartment, then insert new batteries.
30°
Within about 7 m (23 feet)
Distance: About 7 m (23 feet) from the front of the
remote sensor
Angle:
About 30° in each direction of the front of
the remote sensor
Others
Make sure to match the + and – on the batteries
to the marks inside the battery compartment.
POWER ON
* Do not expose the remote sensor of the player to a
strong light source such as direct sunlight or other
illumination. If you do so, you may not be able to
operate the player via the remote control.
Notes on the remote control
• Direct the remote control at the remote sensor of the
player.
• Do not drop or give the remote control a shock.
• Do not leave the remote control near an extremely hot or
humid place.
• Do not spill water or put anything wet on the remote
control.
• Do not open the remote control.
57
Others
LIMITED WARRANTY PORTABLE DVD PLAYER
Toshiba America Consumer Products, Inc. (“TACP”) and Toshiba Hawaii, Inc. (“THI”) make the following limited warranties.
These limited warranties extend to original consumer purchaser or any person receiving this set as a gift from the original
consumer purchaser and to no other purchaser or transferee.
Limited Ninety (90) Day Warranty
TACP/THI warrant this product against defects in materials
or workmanship for a period of ninety (90) days after the
date of original retail purchase. During this period, TACP/
THI will repair a defective product or part, without charge to
you. You must deliver the entire product to a TACP/THI
Authorized Service Station. You are responsible for all
transportation and insurance charges for the unit to and
from the Authorized Service Station.
Limited One (1) Year Warranty
TACP/THI further warrant the parts in this product against
defects in materials or workmanship for a period of one (1)
year after the date of original retail purchase. During this
period, TACP/THI will repair or replace a defective part,
without charge to you, except that if a defective part is
replaced after ninety (90) days from the date of the original
retail purchase you pay labor charges involved in the
replacement. You must also deliver the entire product to a
TACP/THI Authorized Service Station. You are responsible
for all transportation and insurance charges for the unit to
and from the Authorized Service Station.
Rental Units
The warranty for rental units begin with the first rental or
thirty (30) days from the date of shipment to the rental firm,
whichever comes first.
58
Commercial Units
Products sold and used for commercial use have a limited
ninety (90) day warranty for all parts and labor.
Owner’s Manual
You should read the owner’s manual thoroughly before
operating this product. You should complete and mail the
enclosed Demographic card within ten (10) days after you,
or the person who has given you this product as a gift,
purchased this product. This is one way to enable TACP to
provide you with better customer service and improved
products. Failure to return the card will not affect your rights
under this warranty.
Your Responsibility
The above warranties are subject to the following
conditions:
(1) You must retain your bill of sale or provide other proof of
purchase.
(2) You must notify a TACP/THI/TCL Authorized Service
Station within thirty (30) days after you discover a
defective product or part.
(3) All warranty servicing of this product must be made by a
TACP/THI/TCL Authorized Service Station.
(4) U.S.A. warranties are effective only if the product is
purchased and operated in the Continental U.S.A. or
Puerto Rico.
(5) Labor service charges for set installation. Set up,
adjustment of customer controls and installation or
repair of antenna systems are not covered by this
warranty. Reception problems caused by inadequate
antenna systems are your responsibility.
(6) Warranties extend only to defects in materials or
workmanship as limited above and do not extend to any
product or parts which have been lost or discarded by
you or to damage to products or parts caused by
misuse, accident, damage caused by Acts of God, such
as lighting or fluctuations in electric power, improper
installation, improper maintenance or use in violation of
instructions furnished by us; or to units which have
been altered or modified without authorization of TACP/
THI/TCL or to damage to products or part thereof which
have had the serial number removed, altered, defaced
or rendered illegible.
(7) Physically damaged DVD Units are not acceptable for
repair or exchange whether in or out of warranty and
will be returned as received.
How to Obtain Service
(1) Refer to the troubleshooting guide in your owner’s manual. This checklist may solve your problem or check our web
site at WWW.TOSHIBA.COM/TACP.
(2) Products shipped to the Service Station must be insured and safely and securely packed, preferably in the original
shipping carton, and a letter explaining the defect and also a copy of the bill of sale or other proof of purchase must be
enclosed.
In United States contact:
Toshiba America Consumer Products Inc.
(800)-631-3811
In Hawaii contact:
Toshiba Hawaii, Inc.
327 Kamakee St
Honolulu, HI 96814
(808)-521-5377
In Canada contact:
Consumer Electronics Group
191 McNabb St
Markham, Ontario L3R 8H2
(905)-470-5400
Consumer Electronics Group
22171 Fraserwood Way
Richmond, B.C. V6W 1J5
(604)-303-2500
Consumer Electronics Group
1643 North Service Rd
Dorval, QC H9P 1J1
(514)-856-4100
ATTENTION CANADIAN CONSUMERS: (Toshiba Canada “TCL”)
Canadian consumers are requested to complete the special Canadian “Warranty Registration Form” enclosed, and forward
this completed form with a copy of bill of sale to TOSHIBA OF CANADA to “Register and Validate” their warranty. Product
must be purchased from an Authorized Canadian Dealer.
IMPORTANT: PACKING AND SHIPPING INSTRUCTION
When you send the product to a Service Station, you must use the original carton box and packing material, then insert the
original carton box containing the unit into another carton, using more packing material.
Products purchased in the U.S.A. and used in Canada are not covered by these warranties.
Products purchased in Canada and used in the U.S.A. are not covered by these warranties.
59
Others
All warranties implied by state law, including the implied warranties of merchantability and fitness for a particular purpose, are
expressly limited to the duration of the limited warranties set forth above. With the exception of any warranties implied by state
law as hereby limited, the foregoing warranty is exclusive and in lieu of all other warranties, guarantees, agreements and
similar obligations of manufacturer or seller with respect to the repair or replacement of any parts. In no event shall TACP/THI
be liable for consequential or incidental damages.
No person, agent, distributor, dealer or company is authorized to change, modify or extend the terms of these warranties in
any manner whatsoever. The time within which an action must be commenced to enforce any obligation of TACP/THI arising
under the warranty or under any statute, or law of the Unite States or any state thereof, is hereby limited to ninety (90) days
from the date you discover or should have discovered the defect. This limitation does not apply to implied warranties arising
under state law.
This warranty gives you specific legal rights and you may also have other rights, which may vary from state to state. Some
states do not allow limitation on how long an implied warranty lasts, when an action may be brought, or the exclusion or
limitation of incidental or consequential damages, so the above provisions may not apply to you.
Printed in Japan
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement