GE Profile DPSB620GCWW Gas Dryer

GE Profile DPSB620GCWW Gas Dryer
TM
DPSB620GCCC/WW – GE Profile™ King-size 7.0 Cu. Ft. Capacity Gas Dryer
Dryer Dimensions (in inches)
23-1/2
28-1/4
*24-1/2" from the edge of the side panel to the front.
25-1/2" from front to edge of endcaps.
25-1/2*
8-1/2
27
36
42
2-1/2
Side View
Exhaust Options:
When viewed from the front of the unit, exhaust 3-way via rear, left and bottom.
Dryer is shipped exhausted to the rear. Alternate exhausting knockouts
are supplied.
Gas:
An individual properly-grounded branch circuit, with a three-prong grounding-type
receptacle, protected by a 15 or 20 amp circuit breaker or a time-delay fuse is required.
Gas Dryer Electric Rating:
120V, 60Hz, 6A
11-1/2
2
3-1/2
Rear View
Gas (BTU/HR):
22,000. Factory-equipped for natural gas. Tested for LP gas. LP gas supply
requires a conversion kit. Check installation instructions for correct kit and have
a qualified gas technician install a conversion kit. See dryer ducting information
for proper installation.
Note:
Dryer wall outlet must be located within 36" of service cord entry and accessible
when dryer is mounted in position.
Installation Information:
For complete information, see installation instructions packed with your dryer.
R
Listed by
Underwriters
Laboratories
For answers to your Monogram,® GE Profile™ or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center® service, 800.626.2000.
Specification Revised 3/03
TM
DPSB620GCCC/WW – GE Profile™ King-size 7.0 Cu. Ft. Capacity Gas Dryer
Dryer Exhausting Information – Use Metal Duct Only
Vertical and Horizontal Ducting
For complete information, see installation instructions packed with your dryer.
Best Performance
Maximum Length of 4"
Dia. Rigid Metal Duct
Exhaust Hood Type
Maximum Length of 4"
Dia. Flexible Metal Duct
Exhaust Hood Type
Number
of
90°
Turns
A
4" Opening
B
2-1/2"
Opening
A
4" Opening
0
1
2
3
4
0
1
2
3
4
0
1
2
3
0
1
2
3
4
150 ft.
140 ft.
130 ft.
120 ft.
110 ft.
90 ft.
60 ft.
45 ft.
35 ft.
25 ft.
90 ft.
60 ft.
45 ft.
35 ft.
60 ft.
52 ft.
44 ft.
32 ft.
28 ft.
127 ft.
117 ft.
107 ft.
97 ft.
87 ft.
60 ft.
45 ft.
35 ft.
25 ft.
15 ft.
60 ft.
45 ft.
35 ft.
25 ft.
48 ft.
40 ft.
32 ft.
24 ft.
16 ft.
75 ft.
65 ft.
55 ft.
45 ft.
35 ft.
55 ft.
40 ft.
30 ft.
20 ft.
15 ft.
55 ft.
40 ft.
30 ft.
20 ft.
30 ft.
22 ft.
14 ft.
—
—
A
A
4
B
Domestic
Dryer Models
2-1/2
7.3 Capacity Electric
and Gas Dryers
7.0 and 6.0
Capacity Models
all Electric Dryers
7.0 and 6.0
Capacity Models
all Gas Dryers
5.7 Capacity Electric
and Gas Dryers
B
2-1/2"
Opening
52 ft.
42 ft.
32 ft.
22 ft.
12 ft.
45 ft.
30 ft.
20 ft.
15 ft.
10 ft.
45 ft.
30 ft.
20 ft.
15 ft.
18 ft.
14 ft.
10 ft.
—
—
Special Installation Requirements
Alcove or Closet Installation:
• If your dryer is approved for installation in an alcove or closet, it will be stated on a label on the dryer back.
• The dryer MUST be exhausted to the outside.
• Minimum clearances between dryer cabinet and adjacent walls or other surfaces are:
0" either side
3" front and rear
• Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 52”.
• Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq. in. of
open area equally distributed. If this closet contains both a washer and a dryer, doors must contain
a minimum of 120 sq. in. of open area equally distributed.
• No other fuel-burning appliance shall be installed in the same closet with a gas dryer.
Bathroom or Bedroom Installation:
• The dryer MUST be exhausted to the outdoors.
• The installation must conform with the local codes, or in the absence of local codes, with the
National Fuel Gas Code, ANSI Z223.
Minimum Clearances other than Alcove or Closet Installation:
• Minimum clearances to combustible surfaces
0" both sides
3" rear
Specification Revised 3/03
Ducting Materials:
For best performance, this dryer should be vented with 4” diameter all rigid metal exhaust
duct. If “all rigid metal” duct cannot be used, then “flexible all metal” venting can be
used, but it will reduce the maximum recommended duct length.
Exhaust Length Calculation:
1. Determine the number of 90° turns needed for your installation. If you exhaust to the
side or bottom of dryer, add one turn.
2. The maximum length of 4’ rigid (aluminum or galvanized) duct which can be tolerated is
shown in the table. The maximum length for flexible ducts are less than for rigid duct.
A turn of 45° or less may be ignored. Two 45° turns within the duct length should be
treated as a 90° elbow. A turn over 45° should be treated as a 90° elbow.
Exhausting the dryer to the outside is strongly recommended to prevent large
amounts of moisture and lint from being blown into the room. Gas dryers or any dryer
located in a closet must be exhausted to the outside.
Caution: For personal safety do not terminate exhaust into a chimney, under any
enclosed house floor (crawl space), or into an attic, since the accumulated lint could
create a fire hazard or moisture could cause damage. Never terminate the exhaust into
a common duct or plenum with a kitchen exhaust, since the combination of lint and
grease could create a fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird
nesting, etc. The wall cap must also be located at least 12" above the ground or any other
obstruction with the opening pointed down.
Other terminations, such as louvered wall boxes, are acceptable provided they are
equivalent to a 4" opening dampered wall cap.
For more information on venting kits and accessories,
please call 1-800-GE-CARES.
R
Listed by
Underwriters
Laboratories
For answers to your Monogram,® GE Profile™ or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center® service, 800.626.2000.
TM
DPSB620GCCC/WW – GE Profile™ King-size 7.0 Cu. Ft. Capacity Gas Dryer
Features and Benefits
ING
TIME REMAIN
Perfect Dry
POWER
COTTONS
KNITS
WOOLENS
DAMP LESS
DRY
AIR
DRY
DRY
1
CUSTOM
2
MIXED
LOADS
PERM
PRESS
DELICATES
SPEED
DRY
TIMED
DRY
HIGH
MEDIUM
LOW
EXTRA
LOW
DE
WRINKLE
CUSTOM
LOAD
SIZE
START
SIGNAL
MORE
DRY
DRYNESS
LEVEL
TEMP
SET TIME
S
C Y C L E S TAT U
DAMP
SIGNAL
TumblePlus
ANTI
BACTERIAL
EXTEND
TUMBLE
SENSING
TIMED DRY
COOL DOWN
EXTENDED TUMBLE
CLEAN LINT FILTER
STOP
DELAY
START
• King-size Capacity with Deluxe Dryer Rack
NON SENSOR
PRESS & HOLD
TO STORE
• Electronic Controls with Cycle Countdown and LED Indicators
• Stainless Steel Drum
• Multiple Dry Cycles with Custom Cycles and Adaptive Logic System™
• Options including Delay Start, Antibacterial Cycle, Wrinkle Care (Extended Tumble Plus),
Dewrinkle, AirDry and Add Time
• Variable End-of-Cycle Signal
• Dryer Interior Light
• Model DPSB620GCCC – Bisque on bisque
• Model DPSB620GCWW – White on white
Specification Revised 3/03
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement