Toshiba SD-2150 DVD Player

Toshiba SD-2150 DVD Player
OWNER'S MANUAL
DVD VIDEO PLAYER
SD-2150
Nov., 2000 s
Introduction
SAFETY PRECAUTIONS
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS
RISQUE DE CHOC ELECTRIQUE NE
PAS OUVRIR
WARNING :
TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USERSERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk
of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE
ENCLOSURE. DO NOT OPEN THE CABINET. REFER SERVICING TO QUALIFIED PERSONNEL
ONLY.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
ATTENTION:
POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA
FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
CAUTION:
This Digital Video Disc Player employs a Laser System.
To ensure proper use of this product, please read this owner’s manual carefully and retain for
future reference. Should the unit require maintenance, contact an authorized service location see service procedure.
Use of controls or adjustments or performance of procedures other than those specified herein
may result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open the enclosure.
Visible laser radiation when open and interlocks defeated.
DO NOT STARE INTO BEAM.
FCC NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rule. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
WARNING:
2
Changes or modifications made to this equipment, not expressly approved by Toshiba, or parties
authorized by Toshiba, could void the user’s authority to operate the equipment.
In the spaces provided below, record the Model and Serial No. located on the rear panel of your DVD video
player.
Serial No.
Introduction
Model No.
Retain this information for future reference.
Location of the required label
PRODUCT IS CERTIFIED BY THE MANUFACTURER TO
COMPLY WITH DHHS RULE 21CFR SUBCHAPTER J
APPLICABLE AT THE DATE OF MANUFACTURE.
MANUFACTURED
SERIAL NO
TOSHIBA CORPORATION
1-1,SHIBAURA 1-CHOME,MINATO-KU,
TOKYO 105-8001,JAPAN
3
Introduction
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS GIVEN IN THIS
OWNER’S MANUAL AND THOSE MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR
FUTURE REFERENCE.
This set has been designed and manufactured to assure personal safety. Improper use can result in electric
shock or fire hazard. The safeguards incorporated in this unit will protect you if you observe the following
procedures for installation, use and servicing. This unit is fully transistorized and does not contain any parts that
can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.
1. Read owner’s manual
After unpacking this product, read the owner’s manual carefully, and follow
all the operating and other instructions.
2. Power Sources
This product should be operated only from the type of power source indicated
on the label. If you are not sure of the type of power supply to your home,
consult your product dealer or local power company. For products intended
to operate from battery power, or other sources, refer to the operating
instructions.
3. Grounding or Polarization
This product may be equipped with a polarized alternating current line plug
(a plug having one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you are unable to insert
the plug fully into the outlet, try reversing the plug. If the plug should still fail
to fit, contact your electrician to replace your obsolete outlet. Do not defeat
the safety purpose of the polarized plug.
4. Ventilation
Slots and openings in the cabinet are provided for ventilation and to ensure
reliable operation of the product and to protect it from overheating, and these
openings must not be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug or other similar surface.
This product should not be placed in a built-in installation such as a bookcase
or rack unless proper ventilation is provided or the manufacturer’s instructions
have been adhered to.
5. Heat
The product should be situated away from heat sources such as radiators,
heat registers, stoves, or other products (including amplifiers) that produce
heat.
4
6. Water and Moisture
Do not use this product near water - for example, near a bath tub, wash bowl,
kitchen sink, or laundry tub; in a wet basement; or near a swimming pool and
the like.
Introduction
7. Cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
8. Power-Cord Protection
Power-supply cords should be routed so that they are not likely to be walked
on or pinched by items placed upon or against them, paying particular attention
to cords at plugs, convenience receptacles, and the point where they exit
from the product.
9. Overloading
Do not overload wall outlets; extension cords, or integral convenience
receptacles as this can result in a risk of fire or electric shock.
10. Lightning
For added protection for this product during storm, or when it is left unattended
and unused for long periods of time, unplug it from the wall outlet. This will
prevent damage to the product due to lightning and power-line surges.
11. Object and Liquid Entry
Never insert objects of any kind into this product through openings as they
may touch dangerous voltage points or short-out parts that could result in a
fire or electric shock. Never spill liquid of any kind on the product.
12. Attachments
Do not use attachments not recommended by the product manufacturer as they may cause hazards.
5
Introduction
IMPORTANT SAFETY INSTRUCTIONS
13. Accessories
Do not place this product on an unstable cart, stand, tripod, bracket, or table.
The product may fall, causing serious injury to a child or adult, and serious
damage to the product. Use only with a cart, stand, tripod, bracket, or table
recommended by the manufacturer, or sold with the product. Any mounting
of the product should follow the manufacturer’s instructions, and should use
a mounting accessory recommended by the manufacturer.
A product and cart combination should be moved with care. Quick stops,
excessive force, and uneven surfaces may cause the product and cart
combination to overturn.
S3125A
14. Disc Tray
Keep your fingers well clear of the disc tray as it is closing. Neglecting to do
so may cause serious personal injury.
15. Burden
Do not place a heavy object on or step on the product. The object may fall,
causing serious personal injury and serious damage to the product.
16. Headphones
When you use headphones, keep the volume at a moderate level. If you use
the headphones continuously with high volume sound, it may cause hearing
damage.
17. Disc
Do not use a cracked, deformed, or repaired disc. These discs are easily
broken and may cause serious personal injury and product malfunction.
18. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following
conditions:
a) When the power-supply cord or plug is damaged.
b) If liquid has been spilled, or objects have fallen into the product.
c) If the product has been exposed to rain or water.
d) If the product does not operate normally by following the operating instructions. Adjust only those
controls that are covered by the operating instructions as an improper adjustment of other controls may
result in damage and will often require extensive work by a qualified technician to restore the product to
its normal operation.
e) If the product has been dropped or damaged in any way.
f) When the product exhibits a distinct change in performance - this indicates a need for service.
6
19. Servicing
Do not attempt to service this product yourself as opening or removing covers
may expose you to dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
Introduction
20. Replacement Parts
When replacement parts are required, be sure the service technician has used replacement parts specified
by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may
result in fire, electric shock, or other hazards.
21. Safety Check
Upon completion of any service or repairs to this product, ask the service
technician to perform safety checks to determine that the product is in proper
operating condition.
7
Introduction
Precautions
Notes on handling
When shipping the DVD video player, the original
shipping carton and packing materials come in handy.
For maximum protection, repack the unit as it was
originally packed at the factory.
Do not use volatile liquids, such as insect spray, near
the DVD video player. Do not leave rubber or plastic
products in contact with the DVD video player for a
long time. They will leave marks on the finish.
The top and rear panels of the DVD video player may
become warm after a long period of use. This is not a
malfunction.
When the DVD video player is not in use, be sure to
remove the disc and turn off the power.
If you do not use the DVD video player for a long
period, the unit may not function properly in the
future. Turn on and use the DVD video player
occasionally.
Notes on locating
Place the DVD video player on a level surface. Do not
use it on a shaky or unstable surface such as a
wobbling table or inclined stand. The loaded disc may
come off the proper position and cause damage to
the DVD video player.
When you place this DVD video player near a TV,
radio, or VCR, the playback picture may become poor
and the sound may be distorted. In this case, place
the DVD video player away from the TV, radio, or
VCR.
Notes on moisture condensation
Moisture condensation damages the DVD video
player. Please read the following carefully.
Moisture condensation occurs, for example, when you
pour a cold drink into a glass on a warm day. Drops of
water form on the outside of the glass. In the same way,
moisture may condense on the optical pick-up lens
inside this unit, one of the most crucial internal parts of
the DVD video player.
le of mo
Examp ensat isture
ion!
cond
Optical pick-up
lens
Moisture condensation occurs during the
following cases.
When you bring the DVD video player directly from a
cold place to a warm place.
When you use the DVD video player in a room where
you just turned on the heater, or a place where the
cold wind from the air conditioner directly hits the unit.
In summer, when you use the DVD video player in a
hot and humid place just after you move the unit from
an air conditioned room.
When you use the DVD video player in a humid place.
It’s too
warm!
Notes on cleaning
Use a soft, dry cloth for cleaning.
For stubborn dirt, soak the cloth in a weak detergent
solution, wring well and wipe. Use a dry cloth to wipe
it dry.
Do not use any type of solvent, such as thinner and
benzine, as they may damage the surface of the DVD
video player.
If you use a chemical saturated cloth to clean the unit,
follow that product’s instructions.
To obtain a clear picture
The DVD video player is a high technology, precision
device. If the optical pick-up lens and disc drive parts
are dirty or worn down, the picture quality becomes
poor. To obtain a clear picture, we recommend regular
inspection and maintenance (cleaning or parts
replacement) every 1,000 hours of use depending on
the operating environment. For details, contact your
nearest dealer.
8
Do not use the DVD video player when moisture
condensation may occur.
If you use the DVD video player in such a situation, it
may damage discs and internal parts. Remove the
disc, connect the power cord of the DVD video player
to the wall outlet, turn on the DVD video player, and
leave it for two or three hours. After two or three
hours, the DVD video player will have warmed up and
evaporated any moisture. Keep the DVD video player
connected to the wall outlet and moisture
condensation will seldom occur.
Wa
it!
Wall outlet
Notes on Discs
Structure of disc contents
Do not touch the playback side of the disc.
Introduction
On handling discs
Normally, DVD video discs are divided into titles, and the
titles are sub-divided into chapters. VIDEO CDs/audio
CDs are divided into tracks.
DVD video disc
DVD video disc
Title 1
Chapter 1
Title 2
Chapter 2
Chapter 1
Chapter 2
Chapter 3
Playback side
Do not attach paper or tape to discs.
VIDEO CD/Audio CD
VIDEO CD/Audio CD
Track 1
Track 2
Track 3
Track 4
Track 5
On cleaning discs
Fingerprints and dust on the disc cause picture and
sound deterioration. Wipe the disc from the center
outwards with a soft cloth. Always keep the disc
clean.
Each title, chapter or track is assigned a number, which
is called “title number”, “chapter number” or “track
number” respectively.
There may be discs that do not have these numbers.
Notes on copyright
If you cannot wipe off the dust with a soft cloth, wipe
the disc lightly with a slightly moistened soft cloth and
finish with a dry cloth.
Do not use any type of solvent such as thinner,
benzine, commercially available cleaners or antistatic
spray for vinyl LPs. It may damage the disc.
On storing discs
Do not store discs in a place subject to direct sunlight
or near heat sources.
Do not store discs in places subject to moisture and
dust such as a bathroom or near a humidifier.
Store discs vertically in a case. Stacking or placing
objects on discs outside of their case may cause
warping.
It is forbidden by law to copy, broadcast, show,
broadcast on cable, play in public, and rent copyrighted
material without permission.
DVD video discs are copy protected, and any recordings
made from these discs will be distorted.
This product incorporates copyright protection
technology that is protected by method claims of certain
U.S. patents and other intellectual property rights owned
by Macrovision Corporation and other rights owners.
Use of this copyright protection technology must be
authorized by Macrovision Corporation, and is intended
for home and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.
9
Introduction
Notes on Discs (continued)
About this owner’s manual
This owner’s manual explains the basic instructions of
this DVD video player. Some DVD video discs are
produced in a manner that allows specific or limited
operation during playback. As such, the DVD video
player may not respond to all operating commands. This
is not a defect in the DVD video player. Refer to
instruction notes of discs.
“ ” may appear on the TV screen during operation.
A “ ” means that the operation is not permitted by the
DVD video player or the disc.
Playable discs
This DVD video player can play the following discs.
Disc Mark
Contents
Disc
Size
Maximum
playback time
Approx. 4 hours
(single sided disc)
12 cm
Audio
+
video
(moving
pictures)
DVD
video
discs
Approx. 8 hours
(double sided disc)
Approx. 80 minutes
(single sided disc)
8 cm
Notes on region numbers
The region number of this DVD video player is 1. If
region numbers, which stand for their playable area, are
printed on your DVD video disc and you do not find 1
or ALL , disc playback will not be allowed by the player.
(In this case, the DVD video player will display a
message on-screen.)
On VIDEO CDs
This DVD video player supports VIDEO CDs equipped
with the PBC (Version 2.0) function. (PBC is the
abbreviation of Playback Control.) You can enjoy two
playback variations depending on types of discs.
• VIDEO CD not equipped with PBC function
(Version 1.1)
Sound and movie can be played on this DVD video
player in the same way as an audio CD.
• VIDEO CD equipped with PBC function
(Version 2.0)
In addition to operation of a VIDEO CD not equipped
with the PBC function, you can enjoy playback of
interactive software with search function by using the
menu displayed on the TV screen (Menu Playback).
Some of the functions described in this owner’s
manual may not work with some discs.
10
Approx. 160 minutes
(double sided disc)
VIDEO
CDs
DIGITAL VIDEO
Audio
CDs
Audio
+
video
(moving
pictures)
12 cm
Approx. 74 minutes
8 cm
Approx. 20 minutes
12 cm
Approx. 74 minutes
8 cm
(CD
single)
Approx. 20 minutes
Audio
• You cannot play discs other than those listed above.
• You cannot play discs of CD-R, CD-RW, DVD-RAM,
DVD-RW, etc., even if they may be labeled marks
listed above.
• This DVD video player uses the NTSC color system,
and cannot play DVD video discs recorded in any
other color system (PAL, SECAM, etc.).
Table of Contents
SAFETY PRECAUTIONS .......................... 2
IMPORTANT SAFETY INSTRUCTIONS ... 4
Precautions ............................................... 8
Notes on Discs .......................................... 9
Notes on region numbers ............................... 10
Table of Contents.................................... 11
Identification of Controls ....................... 12
Front panel ..................................................... 12
Rear panel ...................................................... 12
DVD display .................................................... 13
Remote control ............................................... 14
Loading batteries ............................................ 15
Operating with the remote control .................. 15
Connections
Connecting to a TV ................................. 16
Advanced playback
Accessing a Specific Location Directly .. 26
Entering the time of the desired location ........ 26
Playing Repeatedly ................................. 27
Repeating a title, chapter, or track .................. 27
Repeating a specific segment ........................ 27
Playing in a Favorite Order .................... 28
Setting titles, chapters, or tracks in a favorite
order ............................................................. 28
Playing in Random Order ...................... 29
Playing titles, chapters or tracks in random
order ............................................................. 29
Zooming a Picture .................................. 30
Zooming a picture ........................................... 30
Selecting 3-D (N-2-2) Sound
Enhancement .......................................... 30
Selecting 3-D (N-2-2) sound enhancement .... 30
Connecting to a TV ......................................... 16
Connecting to an audio system and TV
equipped with ColorStream®
(Component video) inputs ............................ 17
Selecting the Camera Angle .................. 31
Connecting to Optional Equipment ...... 18
Selecting a Language ............................. 33
Connecting to an amplifier equipped with a
Dolby Digital decoder ................................... 18
Connecting to an amplifier equipped with
Dolby Pro Logic Surround ............................ 18
Connecting to an amplifier equipped with a
DTS decoder ................................................ 19
Connecting to an amplifier equipped with an
MPEG2 audio decoder ................................. 19
Connecting to an amplifier equipped with a
digital audio input ......................................... 19
Selecting a playback audio setting ................. 33
Basic playback
Playing a Disc ......................................... 20
Basic playback ............................................... 20
Playing in fast reverse or fast forward
directions ...................................................... 22
Playing frame by frame .................................. 22
Playing in slow-motion .................................... 23
Resuming playback from the same location ... 23
Locating a Specific Title, Chapter, or
Track ........................................................ 24
Introduction
Introduction
Changing the camera angle ........................... 31
Selecting Subtitles ................................. 32
Selecting a subtitle language ......................... 32
Viewing the Operational Information
and DVD/CD-Text .................................... 34
Checking the operational status ..................... 34
Checking the remaining time and setting
status ............................................................ 34
Function setup
Customizing the Function Settings ...... 35
Setting procedure ........................................... 35
Setting details ................................................. 37
Others
Table of Languages ................................ 42
Before Calling Service Personnel ......... 43
Specifications ......................................... 44
LIMITED WARRANTY DVD VIDEO
PLAYER ................................................... 45
Locating a title using the top menu ................. 24
Locating a title by entering the title number .... 24
Locating a specific chapter or track directly .... 25
Locating a specific chapter or track ................ 25
11
Introduction
Identification of Controls
See the page in
for details.
Front panel
OPEN/CLOSE 1/2 buttons 20
POWER indicator 20
STOP button 21
Disc tray 20
PLAY button 20
OPEN/CLOSE
PLAY
1
DISC-1
OPEN/CLOSE
DISC-2
2
STOP
POWER
DISC SELECT
SKIP
PAUSE
DISC-1/2 indicators 20
DVD display 13
PAUSE button 21
SKIP buttons 25
POWER button 20
DISC SELECT button 20
Rear panel
ColorStream® (Component video) VIDEO OUT jacks (Y/PB/PR) 17
VIDEO OUT jack 16
VIDEO OUT
VIDEO
Y
PB
AC IN
PR
AUDIO OUT
S
R
L
ANALOG
BITSTREAM/
PCM
BITSTREAM/PCM AUDIO OUT jack 18 19
AC inlet
ANALOG AUDIO OUT jacks 16 17
Power cord
S VIDEO OUT jack 16
12
Introduction
Pressing of the FL DIMMER button on the remote
control turns the DVD display on or off.
DVD display
FL DIMMER
Off
On
Total playing time/remaining time/elapsed time indicators
Play mode indicator
Disc number indicator
Memory playback indicator
Title/track number indicator
Chapter number indicator
DISC TITLE TRK
CHP INDEX
TOTAL
REMAIN
MEMORY
HDCD
SVCDVD
Multifunctional indicator (indicates operating
status or messages, etc.)
DVD/VIDEO CD/CD indicator
Repeat playback indicator
Angle icon indicator
The indicators vary depending on the kinds of discs you play.
DVD video disc
VIDEO CD
• When closing the disc tray:
Audio CD
• When closing the disc tray:
Example
• When closing the disc tray:
Example
DISC TITLE TRK
CHP INDEX
TOTAL
REMAIN
DISC TITLE TRK
MEMORY
Example
CHP INDEX
TOTAL
REMAIN
MEMORY
HDCD
SVCDVD
HDCD
SVCDVD
Total number of titles
Example
DISC TITLE TRK
Total number of
tracks
Total playing
time of the disc
• During playback:
• During playback:
TOTAL
REMAIN
Elapsed time
of the current
title
Some discs may not display chapter
numbers or elapsed time.
TOTAL
REMAIN
MEMORY
Total number of
tracks
Total playing
time of the disc
Example
CHP INDEX
TOTAL
REMAIN
Playing track 6
DISC TITLE TRK
MEMORY
CHP INDEX
TOTAL
REMAIN
MEMORY
HDCD
SVCDVD
HDCD
SVCDVD
HDCD
SVCDVD
Playing chapter 3
of title 2
DISC TITLE TRK
MEMORY
CHP INDEX
• During playback:
Example
CHP INDEX
DISC TITLE TRK
HDCD
SVCDVD
Elapsed time of
the current
track
Playing track 6
Elapsed time of
the current
track
Some discs may not display track
numbers or elapsed time.
13
Introduction
Identification of Controls (continued)
The instructions in this manual describe the functions on the remote control. See the page in
for details.
Remote control
POWER button 20
DISC SELECT button 20
POWER
DISC SELECT
REV button 22
REV
FWD
SKIP
FWD button 22
PAUSE/STEP
PAUSE/STEP button 21 22
STOP button 21
STOP
PLAY
TOP MENU
MENU
SKIP buttons 25
PLAY button 20
ENTER button 35
MENU button*
TOP MENU button 24
Direction buttons 35
( / / / )
ENTER
RETURN
CLEAR
CLEAR button 25
RETURN button 35
ANGLE
SUBTITLE
AUDIO
ANGLE button 31
AUDIO button 33
SETUP
DISPLAY
ZOOM
3D
SETUP button 35
DISPLAY button 34
3D button 30
SLOW
FL DIMMER
SUBTITLE button 32
SEARCH
SLOW buttons 23
1
2
3
T
Number buttons 24
4
5
6
+10
7
8
9
0
RANDOM MEMORY REPEAT
ZOOM button 30
FL DIMMER button 13
T button 24
A-B RPT
RANDOM button 29
A-B RPT button 27
MEMORY button 28
REPEAT button 27
* MENU button
Use the MENU button to display the menu included on
many DVD video discs. To operate a menu, follow the
instructions in “Locating a title using the top menu.”
24
14
1
Open the cover.
Operating with the remote control
Point the remote control at the remote
sensor and press the buttons.
1
DISC-1
DISC-2
30°
2
Insert batteries (AA size).
Introduction
Loading batteries
2
30°
Within about 7 m (23 feet)
Distance: About 7 m (23 feet) from the front of the
remote sensor
Angle:
About 30° in each direction of the front of
the remote sensor
Make sure to match the + and – on the batteries
to the marks inside the battery compartment.
3
Close the cover.
Notes on batteries
Improper use of batteries may cause battery leakage and
corrosion. To operate the remote control correctly, follow the
instructions below.
• Do not insert batteries into the remote control in the wrong
direction.
• Do not charge, heat, open, or short-circuit the batteries.
Do not throw batteries into a fire.
• Do not leave dead or exhausted batteries in the remote
control.
• Do not use different types of batteries together, or mix old
and new batteries.
• If you do not use the remote control for a long period of
time, remove the batteries to avoid possible damage from
battery corrosion.
• If the remote control does not function correctly or if the
operating range becomes reduced, replace all batteries
with new ones.
• If battery leakage occurs, wipe the battery liquid from the
battery compartment, then insert new batteries.
* Do not expose the remote sensor of the DVD video
player to a strong light source such as direct
sunlight or other illumination. If you do so, you may
not be able to operate the DVD video player via the
remote control.
Notes on the remote control
• Direct the remote control at the remote sensor of the DVD
video player.
• Do not drop or give the remote control a shock.
• Do not leave the remote control near an extremely hot or
humid place.
• Do not spill water or put anything wet on the remote
control.
• Do not open the remote control.
15
Connections
Connecting to a TV
Connect the DVD video player to your TV.
For details of output sound, see 33 .
Connecting to a TV
Signal flow
VIDEO OUT
VIDEO
Y
PB
AC IN
PR
AUDIO OUT
S
To S VIDEO
OUT
R
L
ANALOG
BITSTREAM/
PCM
(red)
To ANALOG
AUDIO OUT
(white)
(yellow)
To wall outlet
To VIDEO OUT
Audio/video cable
(supplied)
To audio inputs
(red)
S video cable (not supplied)
If the TV has an S video input, connect the
DVD video player with an S video cable.
When using an S video cable, do not
connect the yellow video cable.
To video
input
(white)
(yellow)
To S video input
TV or monitor with
audio/video inputs
• Make the following setting.
On-screen display
Select:
Page
“Audio Out Select”
“Analog 2ch”
35
39
Notes
• Refer to the owner’s manual of the connected TV as well.
• When you connect the DVD video player to your TV, be sure to turn off the power and unplug both units from the wall outlet
before making any connections.
• If your television set has one audio input, connect the DVD video player to a Y cable adapter (not supplied) and then connect
to your TV.
• Connect the DVD video player directly to your TV. If you connect the DVD video player to a VCR, TV/VCR combination or
video selector, the playback picture may be distorted as DVD video discs are copy protected.
16
Connecting to an audio system and TV equipped with ColorStream® (Component video) inputs
Connections
Signal flow
VIDEO OUT
VIDEO
Y
PB
AC IN
PR
AUDIO OUT
R
L
ANALOG
S
(red)
BITSTREAM/
PCM
(white)
To ANALOG
AUDIO OUT
To PR
VIDEO
OUT
To PB
VIDEO
OUT
To Y
VIDEO
OUT
To wall outlet
To audio inputs of
the amplifier
(red)
(white)
To Y video input
To PB video input
To PR video input
Audio system
ColorStream® (Component video) outputs/inputs
Some TVs or monitors are equipped with component video inputs. Connecting to
these inputs allows you to enjoy higher quality picture playback.
Actual labels for component video inputs may vary depending on the TV
manufacturer. (ex. Y, R-Y, B-Y or Y, CB, CR)
In some TVs or monitors, the color levels of the playback picture may be reduced
slightly or the tint may change. In such a case, adjust the TV or monitor for
optimum performance.
TV or monitor with
component video inputs
• Make the following setting.
On-screen display
Select:
Page
“Audio Out Select”
“Analog 2ch”
35
39
Notes
• Refer to the owner’s manual of the connected equipment as well.
• When you connect the DVD video player to other equipment, be sure to turn off the power and unplug all of the equipment
from the wall outlet before making any connections.
• If you place the DVD video player near a tuner or radio, the radio broadcast sound might be distorted. In this case, place the
DVD video player away from the tuner and radio.
• The output sound of the DVD video player has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate
listening level. Otherwise, the speakers may be damaged by a sudden high volume sound.
• Turn off the amplifier before you connect or disconnect the DVD video player’s power cord. If you leave the amplifier power
on, the speakers may be damaged.
17
Connections
Connecting to Optional Equipment
You can enjoy high quality dynamic sounds by connecting the DVD video player
to optional audio equipment.
For connection to your TV, see “Connecting to a TV” 16 17 .
For details of output sound, see 33 .
: Front speaker
: Rear speaker
: Sub woofer
: Center speaker
: Signal flow
Connecting to an amplifier equipped with a Dolby Digital decoder
Dolby Digital
Dolby Digital is the surround sound technology used in theaters showing the latest movies,
and is now available to reproduce this realistic effect in the home. You can enjoy motion
picture and live concert DVD video discs with this dynamic realistic sound by connecting the
DVD video player to a 6 channel amplifier equipped with a Dolby Digital decoder or Dolby
Digital processor. If you have a Dolby Pro Logic Surround decoder, you will obtain the full
benefit of Pro Logic from the same DVD movies that provide full 5.1-channel Dolby Digital
soundtracks, as well as from titles with the Dolby Surround mark.
VIDEO OUT
VIDEO
Amplifier equipped
with a Dolby Digital
decoder
Y
PB
PR
AUDIO OUT
R
L
ANALOG
S
BITSTREAM/
PCM
To BITSTREAM/
PCM AUDIO OUT
75 Ω coaxial cable
Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D
symbol are trademarks of Dolby
Laboratories. Confidential unpublished
works. ©1992-1997 Dolby Laboratories.
All rights reserved.
• Use DVD video discs encoded via
the Dolby Digital recording
system.
• Make the following setting.
On-screen display
Select:
Page
“Audio Out Select”
“Bitstream”
35
39
Recording system
33
D
To digital audio input
Connecting to an amplifier equipped with Dolby Pro Logic Surround
Dolby Pro Logic Surround
You can enjoy the dynamic realistic sound of Dolby Pro Logic Surround by connecting an amplifier and speaker system (right and left
front speakers, a center speaker, and one or two rear speakers).
With an amplifier equipped with Dolby Digital
Connect the equipment the same way as described in “Connecting to an amplifier
equipped with a Dolby Digital decoder.” Refer to that amplifier’s owner’s manual and set
the amplifier so you can enjoy Dolby Pro Logic Surround sound.
With an amplifier not equipped with Dolby Digital
Connect the equipment as follows.
VIDEO OUT
VIDEO
*
Amplifier equipped
with Dolby Pro Logic
Surround
To audio input
Audio cable
18
Y
PB
PR
AUDIO OUT
S
R
L
ANALOG
BITSTREAM/
PCM
To ANALOG
AUDIO OUT
• Make the following setting.
On-screen display
Select:
Page
“Audio Out Select”
“Analog 2ch”
35
39
Be sure to set “Audio Out Select”
to “Analog 2ch” when you enjoy
sounds of Dolby Pro Logic
Surround using this connection.
* Connect one or two rear speakers.
The output sound from the rear speakers will be
monaural even if you connect two rear speakers.
Warning
• When you are connecting (via the BITSTREAM/PCM AUDIO OUT jack) an AV decoder that does not have Dolby Digital,
Digital Theater Systems (DTS) or MPEG2 decoding function, be sure to set “Audio Out Select” to “PCM” from the onscreen displays 35 39 . Otherwise, high volume sound may damage your hearing as well as the speakers.
• When playing DTS-encoded discs (DVD video discs and audio CDs), excessive noise may be output from the analog
stereo jacks. To avoid possible damage to the audio system, you should take proper precautions when the ANALOG
AUDIO OUT jacks of the DVD video player are connected to an amplification system. To enjoy DTS Digital Surround™
playback, an external 5.1 channel DTS Digital Surround™ decoder system must be connected to the BITSTREAM/PCM
AUDIO OUT jack of the DVD video player.
Connecting to an amplifier equipped with a DTS decoder
Connections
Digital Theater Systems (DTS)
“DTS” and “DTS Digital Surround” are
DTS is a high quality surround technology used in theaters and now available for home use,
trademarks of Digital Theater Systems,
on DVD video discs or audio CDs.
Inc.
If you have a DTS decoder or processor, you can obtain the full benefit of 5.1 channel DTS
encoded sound tracks on DVD video discs or audio CDs.
• Use DVD video discs or audio
CDs encoded via the DTS
recording system.
• Make the following setting.
VIDEO OUT
VIDEO
Y
PB
PR
AUDIO OUT
Amplifier equipped
with a DTS decoder
S
R
L
ANALOG
BITSTREAM/
PCM
To BITSTREAM/
PCM AUDIO OUT
75 Ω coaxial cable
To digital audio input
On-screen display
Select:
Page
“Audio Out Select”
“Bitstream”
35
39
Recording system
DTS
33
Connecting to an amplifier equipped with an MPEG2 audio decoder
MPEG2 sound
You can enjoy motion picture and live concert DVD video discs with dynamic realistic sound by
connecting an amplifier equipped with an MPEG2 audio decoder or MPEG2 audio processor.
• Use DVD video discs encoded via
the MPEG2 recording system.
• Make the following setting.
VIDEO OUT
VIDEO
Amplifier equipped
with an MPEG2
audio decoder
Y
PB
PR
AUDIO OUT
S
R
L
ANALOG
BITSTREAM/
PCM
To BITSTREAM/
PCM AUDIO OUT
75 Ω coaxial cable
To digital audio input
On-screen display
Select:
Page
“Audio Out Select”
“Bitstream”
35
39
Recording system
MPEG
33
Connecting to an amplifier equipped with a digital audio input
2 channel digital stereo
You can enjoy the dynamic sound of 2 channel digital stereo by connecting an amplifier
equipped with a digital audio input and speaker system (right and left front speakers).
VIDEO OUT
VIDEO
Y
PB
PR
AUDIO OUT
S
Amplifier equipped with
a digital audio input
75 Ω coaxial cable
R
L
ANALOG
• Make the following setting.
BITSTREAM/
PCM
To BITSTREAM/
PCM AUDIO OUT
On-screen display
Select:
Page
“Audio Out Select”
“PCM”
35
39
To digital audio input
Notes
• DO NOT connect the BITSTREAM/PCM AUDIO OUT jack of the DVD video player to the AC-3 RF input of a Dolby Digital
Receiver. This input on your A/V Receiver is reserved for Laserdisc use only and is incompatible with the BITSTREAM/PCM
AUDIO OUT jack of the DVD video player.
• Connect the BITSTREAM/PCM AUDIO OUT jack of the DVD video player to the “COAXIAL” input of a Receiver or Processor.
• Refer to the owner’s manual of the connected equipment as well.
• When you connect the DVD video player to other equipment, be sure to turn off the power and unplug all of the equipment
from the wall outlet before making any connections.
• The output sound of the DVD video player has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate
listening level. Otherwise, the speakers may be damaged by a sudden high volume sound.
• Turn off the amplifier before you connect or disconnect the DVD video player’s power cord. If you leave the amplifier power
on, the speakers may be damaged.
19
Basic playback
Playing a Disc
This section shows you the basics on how to play a disc.
CAUTION
Keep your fingers well clear of the disc tray as it is closing.
Neglecting to do so may cause serious personal injury.
POWER
1 indicator
DISC-1/2
indicators
3
2, 4
6
OPEN/CLOSE
PLAY
1
DISC-1
OPEN/CLOSE
DISC-2
2
STOP
POWER
DISC SELECT
SKIP
PAUSE
5
DVD display
DVD
VCD
CD
PAUSE STOP
Basic playback
Preparations
• When you want to view a disc, turn on the TV and select the video input connected to the DVD video player.
• When you want to enjoy the sound of discs from the audio system, turn on the audio system and select the input connected
to the DVD video player.
1
Press POWER.
POWER
The DVD video player turns on and
the POWER indicator on the player
illuminates.
When the DVD video player is turned on for
the first time, an initial set-up display appears.
See “Initial set-up” to make the settings before
proceeding to step 2.
2
Press DISC SELECT repeatedly to
select the disc you want.
DISC SELECT
DISC-1
DISC-2
6
Red (lit): The disc is on standby or is
being played.
Green (lit): Secondary standby.
Off: Playback does not start.
Press PLAY.
PLAY
Playback starts.
Press OPEN/CLOSE (1/2).
OPEN/CLOSE
1
Press either button you want.
The disc tray opens.
OPEN/CLOSE
2
3
5
Place a disc on the disc tray.
With the playback
side down.
Do not place more
than one disc.
If you insert a DVD video disc that contains a top
menu, a menu may appear. See “Locating a title
using the top menu.” 24
• You may need to press the TOP MENU or MENU
button to display disc menu (depending on the actual
DVD video disc.)
Note
Even while playing a disc, you can set another disc. Press the
OPEN/CLOSE (1/2) button for a disc which is not played.
Initial set-up
Make the following settings on the display.
• There are two different disc sizes. Place the disc in
the correct guide on the disc tray. If the disc is out of
the guide, it may damage the disc and cause the
DVD video player to malfunction.
• Do not place anything except DVD video discs,
VIDEO CDs or audio CDs on the disc tray.
4
Press OPEN/CLOSE (1/2) to close the
disc tray.
OPEN/CLOSE
1
OPEN/CLOSE
2
Press the button which you pressed
in step 2.
To set another disc, press the other
button.
• Some discs may be automatically played after
having been set. Even in the playback, you can
select a disc to play in step 5.
20
On-Screen Language:
Select the appropriate
on-screen language.
TV Shape: Select a
picture size according to
the aspect ratio of your
TV. (See 38 for details.)
TOSHIBA
Thank you for your purchase of this TOSHIBA DVD Player.
Please make a selection
for On-Screen Language and your TV Shape and
press ENTER button on your remote control.
FIRST SETUP
On-Screen Language
TV Shape
ENG
4:3LB
1 Press / to select “On-Screen Language,” and
press ENTER.
2 Select a language using / , and press ENTER.
3 Press to select “TV Shape,” and press ENTER.
4 Select a picture size using / , and press ENTER.
5 Finally press SETUP.
All your selections are entered and the display
disappears.
To change your settings, see “Customizing the Function
Settings.” 35
To obtain a higher quality picture
5
1
PAUSE/STEP
6
STOP
MENU
ENTER
/
SETUP
TOP MENU
Occasionally, some picture noise not usually visible during a normal broadcast
may appear on the TV screen while playing a DVD video disc because the high
resolution pictures on these discs include a lot of information. While the amount of
noise depends on the TV you use with this DVD video player, you should generally
reduce the sharpness adjustment on your TV when viewing DVD video discs.
About
DVD
VCD
CD
The DVD VCD CD icons on the heading bar show the playable discs for the
function described under that heading.
DVD : You can use this function with DVD video discs.
VCD : You can use this function with VIDEO CDs.
CD
: You can use this function with audio CDs.
About the screen saver
Press PAUSE/STEP during playback.
If you pause a picture of a DVD video disc and leave it
still for a long while, the screen saver of the DVD video
player automatically appears (when “Screen Saver” is
set to “On” 40 ). To turn off the screen saver, press the
PLAY button.
PAUSE/STEP
To resume normal playback, press
the PLAY button.
• The sound is muted during still
mode.
Automatic Power Off function
To stop playback
Press STOP.
STOP
If the DVD video player is stopped, or the screen saver
is engaged for approximately 20 minutes, the DVD
video player will automatically turn itself off.
To remove the disc
Press OPEN/CLOSE (1/2) for the disc you want to
remove.
OPEN/CLOSE
1
Remove the disc after the disc tray
opens completely.
OPEN/CLOSE
2
Be sure to press the OPEN/CLOSE (1/2) button to
close the disc tray after you remove the disc.
Notes
• Do not move the DVD video player during playback. Doing so may damage the disc.
• Use the OPEN/CLOSE (1/2) button to open and close the disc tray. Do not push the disc tray while it is moving. Doing so may
cause the DVD video player to malfunction.
• Do not push up on the disc tray or put any objects other than discs on the disc tray. Doing so may cause the DVD video
player to malfunction.
• In many instances, a menu screen will appear after playback of a movie is completed. Prolonged display of an on-screen
menu may damage your television set, permanently etching that image onto its screen. To avoid this, be sure to press the
STOP button on your remote control once the movie is completed.
21
Basic playback
To pause playback (still mode)
Basic playback
REV
Playing a Disc (continued)
FWD
You can play discs at various speeds, and resume playback from the location
where you stopped playback.
PLAY
PAUSE/STEP
SLOW
DVD
VCD
CD
Playing in fast reverse or fast forward directions
To resume normal playback
Press REV or FWD during playback.
REV
FWD
Press PLAY.
PLAY
REV: Fast reverse playback
FWD: Fast forward playback
DVD
Each time you press the REV or
FWD button, the playback speed
changes.
TV screen
2
x2 the normal
speed
VCD
CD
8
x8 the normal
speed
30
Notes
• The DVD video player mutes sound and omits subtitles
during reverse and forward scan of DVD video discs.
However, the DVD video player plays sound during fast
forward or fast reverse play of audio CDs.
• The playback speed may differ depending on the disc.
x30 the normal
speed
Each time you press the REV or
FWD button, the two speeds
alternate.
TV screen
FR1
FR2
Fast reverse
playback
FF1
DVD
VCD
FF2
Fast forward
playback
Playing frame by frame
Press PAUSE/STEP during still playback.
PAUSE/STEP
Each time you press the PAUSE/
STEP button, the picture advances
one frame.
To resume normal playback
Press PLAY.
PLAY
Note
The sound is muted during frame by frame playback.
22
Playing in slow-motion
DVD
VCD
Press PLAY.
Each time you press the SLOW
button, the slow-motion speed
changes.
SLOW
Basic playback
To resume normal playback
Press SLOW during playback.
PLAY
TV screen
1 2
1 4
1 8
1/2 the normal
speed
1/4 the normal
speed
1/8 the normal
speed
Notes
• The sound is muted during slow-motion playback.
• The playback speed may differ depending on the disc.
If you press the SLOW
button
during playback, you can view the
picture in reverse slow-motion. (Only
when using a DVD video disc.)
SLOW
Each time you press the SLOW
button, the slow-motion speed
changes.
DVD
VCD
CD
1
2
Resuming playback from the same location
Press STOP at the location where you
want to interrupt playback.
STOP
The DVD video player memorizes
the location where playback is
stopped.
Press PLAY.
PLAY
The DVD video player resumes
playback from the location where
you stopped playback.
To start playback from the beginning regardless
of the location where you stopped playback
1 Press STOP twice.
STOP
The DVD video player’s memory is
cleared.
2 Press PLAY.
PLAY
DVD
Playback starts from the
beginning of the current title.
VCD
CD
Playback starts from the
beginning of the disc.
• If you want to return to the beginning of a DVD video
disc, open and close the disc tray once with the
OPEN/CLOSE (1/2) button for the disc you want to
play before pressing the PLAY button.
Notes
• The DVD video player’s memory is also cleared when:
– you unplug the DVD video player from the wall outlet after
you stop playback.
– you change the parental lock setting 40 or select a disc
menu language 37 .
– you open the disc tray for a disc which is played.
– you switch the discs by pressing the DISC SELECT button.
• There may be a difference in the location where playback
resumes depending on the disc.
• Settings you changed using the on-screen displays while the
DVD video player keeps a location in the memory may
function only after the memory is cleared.
23
Basic playback
Locating a Specific Title, Chapter, or Track
Normally, DVD video discs are divided into titles, and the titles are sub-divided into chapters. VIDEO CDs and audio CDs
are divided into tracks. You can quickly locate any specific title, chapter, or track.
DVD video disc
Title 1
Chapter 1 Chapter 2
DVD
1
Chapter 1
Title 2
Chapter 2
VIDEO CD/Audio CD
Chapter 3
Track 1
Track 2
Track 3
Track 4
Track 5
Locating a title using the top menu
Press TOP MENU.
The top menu appears on the TV
screen.
TOP MENU
3
Press ENTER.
Playback starts from chapter 1 of the
selected title.
ENTER
e.g.
2
Press
want.
ENTER
DVD
1
/
/
TITLE 1
TITLE 2
TITLE 3
TITLE 4
/
to select the title you
If the titles in the top menu are
assigned a number, you can directly
locate a specific title by pressing its
designated number with the number
buttons.
Locating a title by entering the title number
Press T.
SEARCH
T
Make sure that the space next to
“Title” is highlighted.
(You can shift the highlight using the
/ buttons.)
Title : 1
Chapter:
2
To select title 12
24
1
Press the corresponding number
buttons for the title you want.
e.g. To select title 2
3
Notes
• The instructions above describe basic procedures which
may vary depending on the contents of the DVD video disc.
If different instructions appear on the TV screen, follow those
instructions.
• If you display the top menu during playback and press the
TOP MENU button again without selecting any title, the DVD
video player may resume playback from the point where you
first pressed the TOP MENU button (depending on the actual
DVD video disc.)
• This method of locating a title is available only on a disc that
contains a top menu.
• Instruction notes of discs may refer to the button that
displays the top menu as TITLE button.
2
1
2
Press PLAY.
PLAY
Playback starts from chapter 1 of the
selected title.
Notes
• Pressing the CLEAR button resets the title and chapter
numbers. To clear the “Title” and “Chapter” display, press the
T button several times.
• This method of locating a title is available only on a disc that
contains title numbers.
TOP MENU
SKIP
PLAY
/
/
/
ENTER
CLEAR
T
Number buttons
DVD
VCD
CD
Press T.
Skip steps 1 and 2 if you are using a VIDEO CD/
audio CD.
4
Press PLAY.
PLAY
Playback starts from the selected
chapter or track.
SEARCH
T
2
Title : 1
Chapter:
Press to highlight the space next to
“Chapter.”
Title : 1
Chapter:
ENTER
3
1
1
To select a title and chapter number at the same
time
Perform step 1, and enter a title number you want in the
space next to “Title” using the number buttons, then
perform steps 2 to 4.
Note
Pressing the CLEAR button resets the title and chapter
numbers. To clear the “Title” and “Chapter” display, press the T
button several times.
Press the corresponding number
buttons for the chapter or track you
want.
You can use the +10 button to select numbers
from 10 through 99.
e.g. To select chapter or track 25
or
DVD
VCD
CD
2
5
+10
+10
5
Locating a specific chapter or track
Press SKIP
or
repeatedly to display
the chapter or track number you want.
Playback starts from the selected chapter or track.
SKIP
To locate succeeding chapters or tracks
SKIP
Playback starts from the beginning of the
current chapter or track.
When you press twice, playback starts
from the beginning of the preceding
chapter or track.
Notes
• Some titles may not display chapter numbers.
• When you set “Title Stop” to “Off” 41 , you can access
chapters in another title. If you go back to the preceding title
by pressing the SKIP
button, the DVD video player
locates the first chapter of the title. When “Title Stop” is set
to “On,” you can access chapters only within the current title.
25
Basic playback
1
Locating a specific chapter or track directly
Advanced playback
Accessing a Specific Location Directly
You can access a specific location by entering its corresponding time (hours,
minutes, seconds).
3
1
2
DVD
VCD
CD
1
Entering the time of the desired location
Press T twice.
You may have to press further
depending on the disc. Press the
button repeatedly until the following
display appears.
SEARCH
T
Time
2
-:- - :- -
Press the number buttons to enter the
time.
e.g.
1
3
26
2
5
3
0
Time
1 : 25 : 30
Press PLAY.
PLAY
Playback starts from the desired
location.
Notes
• Some discs may not respond to this process.
• Some scenes may not be located precisely as you specified.
• This method for accessing specific locations is available
only within the current title of the DVD video disc or within
the current track of the VIDEO CD/audio CD.
Playing Repeatedly
PLAY
You can play a specific title, chapter, track, or segment repeatedly.
CLEAR
REPEAT
A-B RPT
DVD
VCD
CD
1
Repeating a title, chapter, or track
Press REPEAT.
REPEAT
Each time you press the REPEAT
button, the repeat mode changes as
follows.
2
Press PLAY.
PLAY
DVD
DVD
VCD
CD
1
Chapter Repeat
Repeats the current
chapter.
DVD
Title Repeat
Repeats the current
title.
Repeats the current
track.
VCD
CD
Track Repeat
DVD
VCD
CD
Disc Repeat
Repeats the current
disc.
DVD
VCD
CD
All Repeat
Repeats all the discs.
Repeat Off
Resumes normal
playback.
Advanced playback
Chapter Repeat
The DVD video player starts repeat
playback.
Press the PLAY button within about
5 seconds after you press the
REPEAT button.
To resume normal playback
Press CLEAR.
CLEAR
Notes
• Some discs may not permit repeat operation.
• When using a DVD video disc, the “All Repeat” feature may
be canceled when the DVD video player switches to another
disc.
Repeating a specific segment
Press A-B RPT at the beginning of the
segment (point A) you want to play
repeatedly.
To resume normal playback
Press CLEAR.
CLEAR
A-B RPT
A–
2
Press A-B RPT again at the end of the
segment (point B).
A-B RPT
The DVD video player automatically
returns to point A and starts repeat
playback of the selected segment
(A-B).
Notes
• Some discs may not permit A-B repeat operation.
• You cannot set the A-B repeat function for a segment that
includes multiple camera angles 31 .
• You can specify a segment only within the current title or
track.
• There may be a slight difference between point A and the
location where playback actually resumes depending on the
disc.
A–B
27
Advanced playback
Playing in a Favorite Order
3
You can combine your favorite titles, chapters, or tracks and play them in the
order you determine. You can program up to 28 selections into the memory.
(Memory playback)
Title: 2
Chapter: 25
Title: 2
Chapter: 12
/
/
/
2
Title: 1
Chapter: 1
DISPLAY
CLEAR
2
1
DVD
VCD
CD
1
Setting titles, chapters, or tracks in a favorite order
Insert a disc and press MEMORY during
stop.
MEMORY
The following display appears.
D: Disc number
T: Title number or
track number
C: Chapter number
2
MEMORY
D T C
1 – –– –– 8
2 – –– –– 9
3 – – – – – 10
4 – – – – – 11
5 – – – – – 12
6 – – – – – 13
7 – – – – – 14
D
–
–
–
–
–
–
–
T
––
––
––
––
––
––
––
C
– – 15
– – 16
– – 17
– – 18
– – 19
– – 20
– – 21
D
–
–
–
–
–
–
–
T
––
––
––
––
––
––
––
C
– – 22
– – 23
– – 24
– – 25
– – 26
– – 27
– – 28
D
–
–
–
–
–
–
–
T
––
––
––
––
––
––
––
C
––
––
––
––
––
––
––
Select the items in the order you want
by pressing the number buttons, then
ENTER for each item.
Each time you press the / button, the spaces
of “D”, “T” and “C” are highlighted in turn. Highlight
where you want to enter, then press the
corresponding number buttons.
To select tracks from a VIDEO CD/audio CD in
order, press the number buttons for the track,
then press the ENTER button for each selection
you want.
To select another title, chapter or track in the same
disc, you do not need to select the disc number.
To select another chapter in the same title, you do
not need to select the title number.
3
28
Press PLAY while the MEMORY display
appears on the TV screen.
PLAY
The DVD video player starts memory
playback.
To change the programmed selections
1 While the MEMORY display appears on the TV
screen, press / to move the highlighted bar to
the item you want to change.
2 Change the selection following the instructions in
step 2.
To cancel the programmed selections
1 While the MEMORY display appears on the TV
screen, press / to move the highlighted bar to
the item you want to cancel.
2 Press CLEAR.
To resume normal playback from memory
playback
Press CLEAR.
CLEAR
The memory playback indicator
disappears.
To program during playback
If you press the MEMORY button during playback, a
programming display appears.
If you further press the DISPLAY button, you can
display the current MEMORY setting. Follow steps 2
and 3.
Notes
• Some discs may not permit memory playback operation.
• If you press the REPEAT button during memory playback,
the DVD video player repeats the current memory playback.
• If you press the MEMORY or RETURN button while the
MEMORY display appears on the TV screen, the MEMORY
display disappears.
• The programmed selections will be cleared when you turn off
the DVD video player.
• When using a DVD video disc, the memory playback may be
canceled when the DVD video player switches the discs.
Playing in Random Order
You can play titles, chapters within a title, or tracks in random order.
(Random playback)
Title: 1
Chapter: 3
Title: 2
Chapter: 2
2
CLEAR
Title: 3
Chapter: 1
1
DVD
VCD
CD
1
Playing titles, chapters or tracks in random order
To resume normal playback
Press RANDOM.
RANDOM
Press CLEAR.
Each time you press the RANDOM
button, the random playback mode
changes as follows.
DVD
Chapter Random Plays chapters within
the current title in
random order.
DVD
Title Random
VCD
CD
Track Random
Random Off
Notes
• Some discs may not permit random playback operation.
• You cannot use the random playback function in conjunction
with the memory playback function.
Plays titles within the
current disc in random
order.
Plays tracks within the
current disc in random
order.
Resumes normal
playback.
If you press the RANDOM button
during playback, the DVD video
player automatically starts random
playback after finishing the current
title, chapter or track.
2
Press PLAY.
PLAY
The DVD video player starts random
playback.
Press the PLAY button within about
5 seconds after you press the
RANDOM button.
29
Advanced playback
Chapter Random
CLEAR
Advanced playback
Zooming a Picture
You can magnify areas within a picture.
/
/
/
RETURN
CLEAR
ZOOM
DVD
Zooming a picture
Press ZOOM during normal, slow or still
playback.
ZOOM
RETURN
ENTER
CLEAR
As you repeatedly press the ZOOM
button, the magnification level
increases.
To reduce the magnification level,
press the RETURN button.
If you press the / / / buttons,
the zoom point shifts.
When the zoom point reaches an
edge of the picture, the color of
“Zoom” changes.
Pressing the CLEAR button restores
the zoom point to the center of the
picture.
To resume normal playback
Press ZOOM repeatedly so that “Zoom Off” appears.
ZOOM
Notes
• Some discs may not respond to zoom feature.
• During some scenes, the buttons may not work as
described.
• Zooming does not work on subtitles or menus included on
DVD video discs.
• During zoom playback, the / / / buttons cannot work
on menus included on DVD video discs. If you want to view
the menus, cancel the zoom playback.
• The magnification level varies depending on the picture size
you select. 38
Selecting 3-D (N-2-2) Sound Enhancement
You can enjoy expansive virtual surround sound effects from just two speakers.
3D
DVD
VCD
CD
Selecting 3-D (N-2-2) sound enhancement
Press 3D during playback.
3D
The current setting is displayed.
Each time you press the 3D button,
the setting changes as follows.
3D (N – 2 – 2 ) : Off
Off
3D (N – 2 – 2 ) : On
On
Notes
• You may sense a difference in volume between normal and
3-D (N-2-2) enhanced sound.
• 3-D (N-2-2) sound enhancement may not function (or may
not be realized) depending on the sound output setting or
disc recording system 33 .
• If 3-D (N-2-2) sound enhancement is on, Dolby Pro Logic
Surround may not function on output sounds at all, or may
function differently than usual.
Spatializer® 3-Dimensional Sound Processing provided by Desper
Products. Inc.
Certain audio features of this product manufactured under a license
from Desper Products, Inc., Spatializer® and the circle-in-square
device are trademarks owned by Desper Products, Inc.
30
Selecting the Camera Angle
If the scene was recorded from multiple angles, you can easily change
the camera angle of the scene you are watching.
2
1, 2
CLEAR
DVD
1
Changing the camera angle
Press ANGLE while playing a scene
recorded with multiple angles.
ANGLE
Current angle number
Angle icon
Press CLEAR.
CLEAR
To disable the angle icon display on the TV
From the on-screen displays, set “On-Screen Displays”
to “Off.” 40
Monitor the DVD display when you want to change the
camera angle.
Angle : 1
2
Press ANGLE or while the angle
number is displayed on the TV screen.
ANGLE
Each time you press the ANGLE or
button, the camera angle changes.
Notes
• You can change the camera angle during still playback. The
camera angle changes to the new setting when you resume
normal playback.
• If you pause a picture immediately after changing a camera
angle, the resumed playback picture may not display the new
camera angle.
e.g.
Angle : 1
ENTER
Angle : 2
Angle : 3
: Cycles backwards
You can change the camera angle directly by
pressing the number buttons corresponding to its
angle number instead of using the / buttons.
31
Advanced playback
While playing a scene recorded with
multiple angles, the angle icon ( )
appears in the DVD display and on
the TV screen.
Press the ANGLE button while the
angle icon is displayed.
To turn off the angle number display
Advanced playback
Selecting Subtitles
You can display subtitles on the TV screen and select a subtitle language
from those included on the DVD video disc.
/
/
/
SUBTITLE
CLEAR
Good evening!
DVD
1
Bonsoir!
¡Buenas tardes!
Selecting a subtitle language
Press SUBTITLE during playback.
SUBTITLE
The current subtitle setting is
displayed for about 3 seconds.
To turn subtitles on or off
1 Press SUBTITLE during playback.
SUBTITLE
Subtitle : 1 ENG On
Language
Position number
The abbreviation of the language appears instead
of the language name. Refer to the list of
languages and their abbreviations. 42
2
2 Press / while the subtitle setting is displayed on
the TV screen, to select “On” or “Off.”
Displayed for about 3 seconds.
Subtitle : 1 ENG On
ENTER
Press SUBTITLE or while the subtitle
setting is displayed on the TV screen.
SUBTITLE
ENTER
Each time you press the SUBTITLE
or button, the subtitle languages
included on the DVD video disc
change.
Subtitles
Subtitle : 1 ENG Off
e.g.
Subtitle : 1 ENG On
Good evening!
Subtitles are
not displayed.
Subtitle : 2 FRE On
Subtitle : 3 SPA On
: Cycles backwards
To turn off the subtitle setting display,
press the CLEAR button.
Notes
• Some DVD video discs are set to display subtitles
automatically, and you cannot turn them off even if you set
the subtitle function to off.
• During some scenes, the subtitles may not appear
immediately after you select “On.”
• Some DVD video discs will allow you to make subtitle
selections and turn subtitles on or off only via the disc menu.
Notes
• When you turn on the DVD video player or replace a disc, the player returns to the initial default setting 37 .
When you select a subtitle language which is not included on the disc, the DVD video player plays a prior language
programmed on the disc.
• During some scenes, the subtitles may not appear immediately after you change the subtitle language by pressing the
buttons.
32
/
Selecting a Language
You can select a preferred language and sound recording system from those
included on the DVD video disc.
Good morning!
DVD
1
Bonjour!
2
1, 2
CLEAR
¡Buenos días!
Selecting a playback audio setting
Press AUDIO during playback.
AUDIO
The current audio setting is
displayed for about 3 seconds.
Press AUDIO or while the audio
setting is displayed on the TV screen.
AUDIO
Each time you press the AUDIO or
button, the audio settings included
on the DVD video disc change.
Language
Recording system
Audio channel
Audio : 1 ENG PCM 2CH
Audio Out Select : Bitstream
e.g.
ENTER
Output sound format
Audio : 1 ENG PCM 2CH
Audio : 2 FRE
39
Advanced playback
Position
number
2
D 2CH
Audio : 3 SPA PCM 2CH
The abbreviation of the language appears instead
of the language name. Refer to the list of
languages and their abbreviations. 42
: Cycles backwards
If you press the / buttons, you
can select output sound format. 39
To turn off the audio setting display, press the
CLEAR button.
Selecting sound channels of VIDEO CDs
You can switch left and right channels by pressing the
AUDIO button repeatedly during playback.
AUDIO
Notes
• When you turn on the DVD video player or replace a disc,
player returns to the initial default setting 37 .
If you select a sound track which is not included on the disc,
the DVD video player plays a prior sound track programmed
on the disc.
• Some discs allow you to change audio selections only via
the disc menu. If this is the case, press the MENU button
and choose the appropriate language from the selections on
the disc menu.
Output sound conversion table (sampling frequency/quantization bit)
Audio selection from the menu 35 39 and output jacks on the rear panel
Discs
Sound recording system
Dolby Digital
48 kHz/16 bit
48 kHz/20 bit
DVD
Linear 48 kHz/24 bit
video discs
PCM
96 kHz/16 bit
96 kHz/20 bit
96 kHz/24 bit
DTS
MPEG2
VIDEO CDs
MPEG1
Linear PCM 44.1 kHz/16 bit
Audio CDs
DTS
“Bitstream”
“Analog 2ch”
“PCM”
BITSTREAM/PCM ANALOG AUDIO
OUT jacks
jack
BITSTREAM/PCM ANALOG AUDIO
OUT jacks
jack
BITSTREAM/PCM ANALOG AUDIO
OUT jacks
jack
Bitstream
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
Bitstream
Bitstream
44.1 kHz/16 bit
44.1 kHz/16 bit
Bitstream
48 kHz/20 bit
48 kHz/16 bit
48 kHz/20 bit
48 kHz/20 bit
48 kHz/16 bit
48 kHz/20 bit
48 kHz/20 bit
–
–
44.1 kHz/16 bit
44.1 kHz/16 bit
(Noise)
Bitstream
48 kHz/16 bit
48 kHz/16 bit
–
–
–
–
Bitstream
Bitstream (2ch)
44.1 kHz/16 bit
44.1 kHz/16 bit
Bitstream
48 kHz/20 bit
48 kHz/16 bit
48 kHz/20 bit
48 kHz/24 bit
96 kHz/16 bit
96 kHz/20 bit
96 kHz/24 bit
–
48 kHz/16 bit
44.1 kHz/16 bit
44.1 kHz/16 bit
(Noise)
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
–
48 kHz/16 bit
44.1 kHz/16 bit
44.1 kHz/16 bit
Bitstream
48 kHz/20 bit
48 kHz/16 bit
48 kHz/20 bit
48 kHz/20 bit
48 kHz/16 bit
48 kHz/20 bit
48 kHz/20 bit
–
48 kHz/16 bit
44.1 kHz/16 bit
44.1 kHz/16 bit
(Noise)
: 3-D (N-2-2) sound enhancement can function.
33
Advanced playback
Viewing the Operational Information and
DVD/CD-Text
You can view information about a disc and its operational status on the TV
screen.
DISPLAY
DVD
VCD
CD
Checking the operational status
Press DISPLAY during stop.
Each time you press the DISPLAY button, the on-screen display appears as follows.
DISPLAY
DVD
Current title number
Current chapter number
e.g.
→
Stop
Title : 2
Chapter : 1
Operational
status
e.g.
→
Track : 1
Total 0 : 46 : 30
Stop
Operational
status
↓
↓
Displays CD-Text data if included on the audio CDs.
(Some letters may not be displayed properly
depending on the disc.)
Displays DVD-Text data if included on the disc.
(Some letters or sections may not be displayed
properly depending on the disc.)
↓
Turns off.
DVD
VCD
CD
Current track number
Total playing time of the disc
VCD
CD
↓
Turns off.
Checking the remaining time and setting status
Press DISPLAY during playback.
Each time you press the DISPLAY button, the on-screen display appears as follows.
DISPLAY
DVD
Current chapter number
Current title number Operational
status
Playback mode
e.g.
Play
Elapsed Remain
Title : 3 0 :10 : 15 0 : 50 : 45
Chapter : 2 0 :03 : 08 0 :10 : 24
Chapter Repeat
3D (N-2-2) : On
→
D 2 CH
Audio : 1 ENG
Subtitle : 12 ENG Off
Angle : 1
↓
Bit Rate 0
Elapsed time
and remaining
time of the
current title
Elapsed time
and remaining
time of the
current chapter
Current 3-D
(N-2-2) setting
Current audio
setting
Current subtitle
setting
Current angle
setting
10 6 . 0 Mbps
Data transfer rate (Mbit/s)
= Amount of picture, sound and subtitle data in the
DVD video disc transferred per second.
The larger the value is, the more data processed, but
this does not necessarily insure better picture quality.
↓
Displays DVD-Text data if included on the disc.
(Some letters or sections may not be displayed
properly depending on the disc.)
↓
Turns off.
34
VCD
CD
Operational status
Current track number
Playback mode
e.g.
Play
Elapsed Remain
Track : 3 0 :01 : 20 0 : 02 : 00
0 :05 : 12 0 :43 : 00
Disc
Track Repeat
3D (N-2-2) : On
→
Elapsed time
and remaining
time of the
current track
Elapsed time
and remaining
time of the disc
Current 3-D
(N-2-2) setting
↓
Displays CD-Text data if included on the audio CDs.
(Some letters may not be displayed properly
depending on the disc.)
↓
Turns off.
Function setup
Customizing the Function Settings
2
You can change the default settings to customize performance to your preference.
RETURN
LANGUAGE
DVD
VCD
CD
1
PICTURE
DISPLAY
AUDIO
3, 4
1, 6
OPERATION
Setting procedure
Press SETUP during stop.
SETUP
The following on-screen display
appears.
3
Press / to select the setting you
want to change, then press ENTER.
ENTER
ENTER
PICTURE
2
AUDIO
DISPLAY
OPERATION
ENG
ENG
ENG
–––
4
Press / to select a symbol for the
setting you want to change.
Function setup
LANGUAGE
On-Screen Language
Disc Menu Language
Audio Language
Subtitle Language
Change the selection by / or other
buttons, by referring to the
corresponding pages 37 , then press
ENTER.
(See the next page.)
ENTER
ENTER
ENTER
5
Repeat steps 3 and 4 to change other
settings.
6
Press SETUP.
To select another operation, go back to step 2.
Language settings
LANGUAGE
SETUP
The on-screen display disappears.
Picture performance settings
PICTURE
To return to the previous display
Press RETURN.
Output sound settings
RETURN
AUDIO
Display settings
DISPLAY
Operational settings
OPERATION
Notes
• The on-screen display disappears when you press the
SETUP button.
• The SETUP button can function even during normal
playback, however some operations may be inaccessible,
and a message will appear. In this case, try again after
playback is stopped.
35
Function setup
Setting
LANGUAGE
PICTURE
AUDIO
DISPLAY
OPERATION
36
Details
Page
On-Screen Language
DVD
VCD
CD
To select a preferred language for on-screen
displays.
37
Disc Menu Language
DVD
To select a preferred language for disc menus.
37
Audio Language
DVD
To select a preferred language for the sound
track.
37
Subtitle Language
DVD
To select a preferred language for subtitles.
37
TV Shape
DVD
To select a picture size according to the aspect
ratio of your TV.
38
Black Level
DVD
VCD
To select the black level of playback pictures.
38
Audio Out Select
DVD
VCD
CD
To select an output sound format
corresponding to your system connection.
39
Dynamic Range Control
DVD
To turn on or off a function that makes faint
sounds easier to hear even if you lower the
volume during late hours playback.
39
Karaoke Vocal
DVD
To turn on or off the vocal output during DVD
KARAOKE disc playback.
39
On-Screen Displays
DVD
VCD
CD
To turn on or de-activate the operational status
display on the TV screen.
40
OSD Background Color
DVD
VCD
CD
To select the background color for on-screen
displays.
40
Screen Saver
DVD
To turn the screen saver on or off.
40
Pause/Still
DVD
To select the resolution of still pictures.
(Field/Frame)
40
Parental Lock
DVD
To turn the parental lock function on or off.
40
Remote Confirmation
DVD
VCD
CD
To turn on or off the confirmation beeper for
each remote command received.
41
Title Stop
DVD
To turn on or off a feature that automatically
stops playback after a title has been viewed.
41
PBC
VCD
To use the menu screen when playing a PBCcontrollable VIDEO CD.
41
Customizing the Function Settings (continued)
Setting details
PICTURE
LANGUAGE
LANGUAGE
On-Screen Language
Disc Menu Language
Audio Language
Subtitle Language
On-Screen Language
DVD
AUDIO
DISPLAY
OPERATION
English:
French:
Spanish:
Others:
ENG
ENG
ENG
–––
VCD
CD
English: To view on-screen displays in English.
French: To view on-screen displays in French.
Spanish: To view on-screen displays in Spanish.
DVD
To play sound tracks in English.
To play sound tracks in French.
To play sound tracks in Spanish.
To make a further choice.
After pressing the ENTER button, follow
steps 1) - 4) below.
1) Obtain the abbreviation of the preferred
language from the list 42 .
2) Select the first character by pressing the /
buttons.
3) Press the / buttons to shift and select the
second character by pressing the /
buttons.
DVD
PICTURE
English:
French:
Spanish
Others:
Function setup
Disc Menu Language
Audio Language
LANGUAGE
On-Screen Language
Disc Menu Language
Audio Language
Subtitle Language
To display disc menus in English.
To display disc menus in French.
To display disc menus in Spanish.
To make a further choice.
After pressing the ENTER button, follow
steps 1) - 4) below.
1) Obtain the abbreviation of the preferred
language from the list 42 .
2) Select the first character by pressing the /
buttons.
3) Press the / buttons to shift and select the
second character by pressing the / buttons.
PICTURE
LANGUAGE
On-Screen Language
Disc Menu Language
Audio Language
Subtitle Language
AUDIO
ENG
PA
ENG
–––
DISPLAY
ENG
ENG
PA
–––
DISPLAY
OPERATION
English
French
Spanish
Others
Code
PA
4) Press the ENTER button.
Note
Some DVD video discs may be played in a different
language than you selected. A prior language may be
programmed on the disc.
OPERATION
Subtitle Language
English
French
Spanish
Others
Code
AUDIO
PA
4) Press the ENTER button.
Note
Some DVD video discs may not include your preselected language. In this case, the DVD video player
automatically displays disc menus consistent with the
disc’s initial language setting.
English:
French:
Spanish:
No Subtitle:
Others:
DVD
To display subtitles in English.
To display subtitles in French.
To display subtitles in Spanish.
To disable subtitles.
To make a further choice.
After pressing the ENTER button,
follow steps 1) - 4) below.
1) Obtain the abbreviation of the preferred
language from the list 42 .
2) Select the first character by pressing the
buttons.
/
(Continued)
37
Function setup
Customizing the Function Settings (continued)
Setting details
(Continued)
LANGUAGE
3) Press the / buttons to shift and select the
second character by pressing the /
buttons.
PICTURE
LANGUAGE
On-Screen Language
Disc Menu Language
Audio Language
Subtitle Language
AUDIO
ENG
ENG
ENG
PA
DISPLAY
PICTURE
AUDIO
DISPLAY
OPERATION
4 : 3LB
NRML
OPERATION
English
French
Spanish
No Subtitle
Others
Code
PICTURE
TV Shape
Black Level
TV Shape
PA
4:3 Letterbox:
Select when a standard 4:3 TV is
connected.
Displays theatrical images with
masking bars above and below the
picture.
4:3 Normal:
Select when a standard 4:3 TV is
connected.
Displays pictures cropped to fill
your TV screen. Either or both
sides of the picture are cut off.
4) Press the ENTER button.
Notes
• Some DVD video discs may be set to display subtitles
in a different language than you selected. A prior
subtitle language may be programmed on the disc.
• Some DVD video discs allow you to change subtitle
selections only via the disc menu. If this is the case,
press the MENU button and choose the appropriate
subtitle language from the selection on the disc menu.
DVD
16:9 Widescreen: Select when a 16:9 wide TV is
connected.
Notes
• The displayable picture size is preset on the DVD video
disc. Therefore, the playback picture of some DVD
video discs may not conform to the picture size you
select.
• When you play DVD video discs recorded in the 4:3
picture size only, the playback picture always appears
in the 4:3 picture size regardless of the TV shape
setting.
• If you select “16:9 Widescreen” and you own a 4:3 TV
set, the DVD playback picture will be horizontally
distorted during playback. Images will appear to be
horizontally compressed. Always be sure that your TV
shape conforms to the actual TV in use.
Black Level
DVD
VCD
Set to your preference and monitor’s ability.
Enhanced: Expanded black level. (0 IRE)
Normal:
Standard black level. (7.5 IRE)
38
Karaoke Vocal
LANGUAGE
AUDIO
AUDIO
Audio Out Select
Dynamic Range Control
Karaoke Vocal
Audio Out Select
DVD
DISPLAY
PICTURE
VCD
Bitstream
On
Off
CD
Select the output sound format corresponding to your
system connection.
For details of sound recording systems, see 33 .
Off: The primary vocal is not output.
On: The primary vocal is output when it is recorded
on the disc.
Notes
• The vocal output feature is used during playback of
Dolby Digital (multi-channel) recorded DVD KARAOKE
discs. This feature allows you to turn off vocal audio
tracks, or restore them for background accompaniment.
• When playing KARAOKE, connect appropriate audio
equipment such as an amplifier to the DVD video
player.
Function setup
Bitstream:
DVD
OPERATION
Select when connected to an amplifier
equipped with a Dolby Digital, DTS,
MPEG1 or MPEG2 decoder. 18 19
The DVD video player outputs digital
audio information in the bitstream
format when you play a DVD video disc
recorded on the Dolby Digital, DTS,
MPEG1 or MPEG2 recording system.
Analog 2ch: Select when connected to a TV, or
Dolby Pro Logic or stereo system via
the analog audio jacks. 16 18
PCM:
Select when connected to a 2 channel
digital stereo amplifier. 19
The DVD video player outputs sounds
in the PCM 2ch format when you play a
DVD video disc recorded on the Dolby
Digital, MPEG1 or MPEG2 recording
system.
Dynamic Range Control
DVD
Off: Full dynamic range is maintained.
On: Dynamic range is reduced.
Notes
• This function works only during playback of Dolby
Digital recorded discs.
• The level of Dynamic Range Reduction may differ
depending on the DVD video disc.
39
Function setup
Customizing the Function Settings (continued)
Setting details
LANGUAGE
DISPLAY
PICTURE
On-Screen Displays
DVD
On
Gray
On
VCD
Off: Operational modes (e.g. “Play”, “
displayed.
On: Operational modes (e.g. “Play”, “
displayed on-screen.
OSD Background Color
DVD
Blue: Blue background.
Gray: Gray background.
Screen Saver
OPERATION
AUDIO
DISPLAY
On-Screen Displays
OSD Background Color
Screen Saver
DVD
Off: The screen saver is disengaged.
On: The screen saver operates.
LANGUAGE
OPERATION
Pause/Still
CD
”) are not
”) are
VCD
PICTURE
OPERATION
Pause/Still
Parental Lock
Remote Confirmation
Title Stop
PBC
AUDIO
DISPLAY
Auto
Off
On
Off
On
DVD
Auto:
For normal use. Still and fast motion images
can be paused.
Frame: The resolution of still pictures is improved,
so that you can make a motionless picture
more clearer when you pause it.
CD
Parental Lock
DVD
DVD video discs equipped with the parental lock
function are rated according to their content. The
contents allowed by a parental lock level and the way
a DVD video disc can be controlled may vary from
disc to disc. For example, if the disc allowed you
could edit out violent scenes unsuitable for children
and replace them with more suitable scenes, or lock
out playback of the disc altogether.
• DVD video discs may or may not respond to the
parental lock settings. This is not a defect in the DVD
video player. Make sure this function works with your
DVD video discs.
Off: The parental lock feature does not function.
After pressing the ENTER button, follow step 1)
below.
On: To activate the parental lock feature or change
the settings.
After pressing the ENTER button, follow steps
1) - 3) below.
LANGUAGE
PICTURE
OPERATION
Pause/Still
Parental Lock
Remote Confirmation
Title Stop
PBC
40
DISPLAY
AUDIO
Auto
Off
On
Off
On
Off
On
Security Code
1) Press the number buttons to create a personal
4-digit security code, then press ENTER.
If you make a mistake before pressing the
ENTER button, press the CLEAR button and
enter your 4-digit security code again.
2) Press the / buttons to select the country
whose standards were used to rate the DVD
video disc.
CANADA
Viewable
STOP
STOP
STOP
STOP
ENTER
The 4-digit security code is cleared.
2) Press the number buttons to create a new
4-digit security code.
3) Press the ENTER button.
Remote Confirmation
DVD
VCD
CD
Function setup
Level 8
Level 7
Level 6
Level 5
Level 4
Level 3
Level 2
Level 1
To change your 4-digit security code
1) After selecting “On” or “Off,” press the STOP
button four times, then press the ENTER
button.
Off: The beeper does not sound.
On: The beeper sounds with each remote operation.
3) Press the / buttons to select the parental
lock level, then press the ENTER button.
CANADA
Locked
Viewable
Level8
Level 7
Level 6
Level 5
Level 4
Level 3
Level 2
Level 1
You cannot play DVD video discs rated higher than
the level you selected unless you cancel the parental
lock function.
For example, when you select level 7, discs rated
higher than level 7 are locked out and cannot be
played.
Title Stop
DVD
Off: The DVD video player continues after playback
of a title is completed.
On: The DVD video player stops after playback of a
title is completed.
PBC
VCD
Off: When playing a VIDEO CD without using the
menu.
On: To use the menu when playing a PBC-featured
VIDEO CD.
The parental lock level is equivalent to the following
USA movie ratings.
Level 7: NC-17
Level 6: R
Level 4: PG 13
Level 3: PG
Level 1: G
The parental lock levels for “CANADA” are included
for future use. Check the appropriate parental lock
level when you buy a DVD video disc equipped with
the parental lock feature in the future.
To change the parental lock level
Follow steps 1) - 3).
41
Others
Table of Languages
Table of languages and their abbreviations
Abbreviation
–––
CHI (ZH)
DUT (NL)
ENG (EN)
FRE (FR)
GER (DE)
ITA (IT)
JPN (JA)
KOR (KO)
MAY (MS)
SPA (ES)
AA
AB
AF
AM
AR
AS
AY
AZ
BA
BE
BG
BH
BI
BN
BO
BR
CA
CO
CS
CY
DA
DZ
EL
EO
ET
EU
FA
FI
FJ
FO
FY
GA
GD
GL
42
Language
No alternate
language
Chinese
Dutch
English
French
German
Italian
Japanese
Korean
Malay
Spanish
Afar
Abkhazian
Afrikaans
Amharic
Arabic
Assamese
Aymara
Azerbaijani
Bashkir
Belorussian
Bulgarian
Bihari
Bislama
Bengali, Bangla
Tibetan
Breton
Catalan
Corsican
Czech
Welsh
Danish
Bhutani
Greek
Esperanto
Estonian
Basque
Persian
Finnish
Fiji
Faroese
Frisian
Irish
Scottish Gaelic
Galician
Abbreviation
GN
GU
HA
HI
HR
HU
HY
IA
IE
IK
IN
IS
IW
JI
JW
KA
KK
KL
KM
KN
KS
KU
KY
LA
LN
LO
LT
LV
MG
MI
MK
ML
MN
MO
MR
MT
MY
NA
NE
NO
OC
OM
OR
PA
PL
PS
Language
Guarani
Gujarati
Hausa
Hindi
Croatian
Hungarian
Armenian
Interlingua
Interlingue
Inupiak
Indonesian
Icelandic
Hebrew
Yiddish
Javanese
Georgian
Kazakh
Greenlandic
Cambodian
Kannada
Kashmiri
Kurdish
Kirghiz
Latin
Lingala
Laotian
Lithuanian
Latvian, Lettish
Malagasy
Maori
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Maltese
Burmese
Nauru
Nepali
Norwegian
Occitan
(Afan) Oromo
Oriya
Panjabi
Polish
Pashto, Pushto
Abbreviation
PT
QU
RM
RN
RO
RU
RW
SA
SD
SG
SH
SI
SK
SL
SM
SN
SO
SQ
SR
SS
ST
SU
SV
SW
TA
TE
TG
TH
TI
TK
TL
TN
TO
TR
TS
TT
TW
UK
UR
UZ
VI
VO
WO
XH
YO
ZU
Language
Portuguese
Quechua
Rhaeto-Romance
Kirundi
Rumanian
Russian
Kinyarwanda
Sanskrit
Sindhi
Sango
Serbo-Croatian
Singhalese
Slovak
Slovenian
Samoan
Shona
Somali
Albanian
Serbian
Siswati
Sesotho
Sundanese
Swedish
Swahili
Tamil
Telugu
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Setswana
Tongan
Turkish
Tsonga
Tatar
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapük
Wolof
Xhosa
Yoruba
Zulu
Before Calling Service Personnel
Check the following guide for the possible cause of a problem before contacting service.
Symptoms and correction
Symptom
Cause
Correction
No power.
• The power plug is disconnected.
• Connect the power plug securely into the
wall outlet.
16
The DVD video player turned
off by itself.
• The automatic power off function turned
the unit off.
• Press the PLAY button.
21
No picture.
• The TV is not set to receive DVD signal
output.
• Select the appropriate video input mode
on the TV so the picture from the DVD
video player appears on the TV screen.
20
• The video cable is not connected securely.
• Connect the video cable securely into the
appropriate jacks.
16, 17
• The equipment connected with the audio
cable is not set to receive DVD signal
output.
• Select the correct input mode of the
audio receiver so you can listen to the
sound from the DVD video player.
• The audio cable is not connected securely.
• Connect the audio cable securely into the
appropriate jacks.
• The audio receiver or TV is turned off.
• Turn on the equipment connected with
the audio cable.
• The setting of output sound format is
incorrect.
• Select the proper audio setting.
The playback picture has
occasional distortion.
• The disc is dirty.
• Eject the disc and clean it.
9
• It is in fast forward or fast reverse
playback.
• Sometimes a small amount of picture
distortion may appear. This is not a
malfunction.
–
Brightness is unstable or
noises are present in the
playback pictures.
• The effect of copy protection.
• Connect the DVD video player directly to
the TV. Avoid connecting the DVD video
player to a VCR or TV/VCR combination.
16
The DVD video player does
not start playback.
• No disc is inserted.
• Insert a disc.
20
• An unplayable disc is inserted.
• Insert a playable disc. (Check the disc
type and color system.)
10
• The disc is placed upside down.
• Place the disc with the playback side
down.
20
• The disc is not placed within the guide.
• Place the disc correctly inside the guide
on the disc tray.
20
• The disc is dirty.
• Clean the disc.
• The parental lock function is set.
• Cancel the parental lock function or
change the parental lock level.
Playback does not follow the
course of the disc’s program.
• It is in the mode of repeat playback,
memory playback, etc.
• These operations may prevent a proper
progress of the contents.
–
Buttons do not work.
• Power supply fluctuations or other
abnormalities such as static electricity may
interrupt correct operations.
• Turn the power on or off with the POWER
button. Or disconnect the power plug and
insert it into the wall outlet again.
–
The remote control does not
work properly.
• The remote control is not pointed at the
remote sensor of the DVD video player.
• Point the remote control at the remote
sensor of the DVD video player.
15
• The remote control is too far from the DVD
video player.
• Operate the remote control within about
7 m.
15
• The batteries in the remote control are
exhausted.
• Replace the batteries with new ones.
15
No sound.
Page
20
16, 17
18, 19
20
33, 35
39
Others
9
35, 40
43
Others
Specifications
DVD video player / outputs / supplied accessories
DVD Video Player
Power supply
120 V AC, 60 Hz
Power consumption
14 W
Mass
3.4 kg
External dimensions
430 × 102 × 313 mm (W/H/D)
Signal system
Standard NTSC
Laser
Semiconductor laser, wavelength 650 nm
Frequency range
DVD linear sound :
Signal-to-noise ratio
More than 112 dB
Audio dynamic range
More than 105 dB
Harmonic distortion
Less than 0.002 %
Wow and flutter
Below measurable level (less than ±0.001 % (W.PEAK))
Operating conditions
Temperature: 5 °C to 35 °C, Operation status: Horizontal
48 kHz sampling 4 Hz to 22 kHz
96 kHz sampling 4 Hz to 44 kHz
Outputs
Video output
1.0 V (p-p), 75 Ω, negative sync., pin jack × 1
S video output
(Y) 1.0 V (p-p), 75 Ω, negative sync., Mini DIN 4-pin × 1
(C) 0.286 V (p-p), 75 Ω
Component video output
(Y) 1.0 V (p-p), 75 Ω, negative sync., pin jack × 1
(PB)/(PR) 0.7 V (p-p), 75 Ω, pin jack × 2
Audio output (BITSTREAM/PCM)
0.5 V (p-p), 75 Ω, pin jack × 1
Audio output (ANALOG AUDIO)
2.0 V (rms), 220 Ω, pin jacks (L, R) × 1
Supplied Accessories
Audio/video cable ................................................. 1
Remote control (SE-R0044) ................................. 1
Batteries (AA) ....................................................... 2
Power cord ............................................................ 1
• Designs and specifications are subject to change without notice.
44
LIMITED WARRANTY DVD VIDEO PLAYER
Toshiba America Consumer Products, Inc. (“TACP”), Toshiba Hawaii (“THI”) and Toshiba Canada Limited (“TCL”) make the
following limited warranties. These limited warranties extend to original purchaser or any person receiving this set as a gift from
the original purchaser and to no other purchaser or transferee.
Limited Ninety (90) Day Warranty
TACP/THI warrant this product against defects in materials
or workmanship for a period of ninety (90) days after the
date of original retail purchase. During this period, TACP/
THI will repair a defective product or part, without charge to
you. You must deliver the entire product to a TACP/THI
Authorized Service Station. You are responsible for all
transportation and insurance charges for the unit to and
from the Authorized Service Station. If you live in the U.S.A.
you may, at your option, return your DVD Unit to:
Toshiba America Consumer Products Inc.
Returns Center
1420C Toshiba Dr.
Lebanon, TN 37087
Upon receipt we will, at our option, exchange the DVD Unit
with a new or refurbished unit. Canadian consumers are
requested to contact TCL. In Hawaii consumers are
requested to contact THI.
Rental Units
The warranty for rental units begin with the first rental or
thirty (30) days from the date of shipment to the rental firm,
whichever comes first.
Owner’s Manual
You should read the owner’s manual thoroughly before
operating this product. You should complete and mail the
enclosed Demographic card within ten (10) days after you,
or the person who has given you this product as a gift,
purchased this product. This is one way to enable TACP to
provide you with better customer service and improved
products. Failure to return the card will not affect your rights
under this warranty.
Your Responsibility
The above warranties are subject to the following
conditions:
(1) You must retain your bill of sale or provide other proof of
purchase.
(2) You must notify a TACP/THI/TCL Authorized Service
Station within thirty (30) days after you discover a
defective product or part.
(3) All warranty servicing of this product must be made by a
TACP/THI/TCL Authorized Service Station.
(4) U.S.A. warranties are effective only if the product is
purchased and operated in the Continental U.S.A. or
Puerto Rico.
(5) Labor service charges for set installation. Set up,
adjustment of customer controls and installation or
repair of antenna systems are not covered by this
warranty. Reception problems caused by inadequate
antenna systems are your responsibility.
(6) Warranties extend only to defects in materials or
workmanship as limited above and do not extend to any
product or parts which have been lost or discarded by
you or to damage to products or parts caused by
misuse, accident, damage caused by Acts of God, such
as lighting or fluctuations in electric power, improper
installation, improper maintenance or use in violation of
instructions furnished by us; or to units which have been
altered or modified without authorization of TACP/THI/
TCL or to damage to products or part thereof which
have had the serial number removed, altered, defaced
or rendered illegible.
(7) Should you elect to return your DVD Unit to TACP after
the ninety (90) days and within one (1) year, or after the
warranty period has expired: Call (800)-631-3811 to
receive information concerning an exchange price.
Payment must be enclosed with product in the form of a
certified check or money order including reason for
return.
(8) Physically damaged DVD Units are not acceptable for
repair or exchange whether in or out of warranty and
will be returned as received.
Others
Limited One (1) Year Warranty
TACP/THI further warrant the parts in this product against
defects in materials or workmanship for a period of one (1)
year after the date of original retail purchase. During this
period, TACP/THI will repair or replace a defective product
or part, at their option, with a new or refurbished product or
part without charge to you, except that if a defective part is
replaced after ninety (90) days from the date of the original
retail purchase you pay labor charges involved in the
replacement. You must also deliver the entire product to a
TACP/THI Authorized Service Station. You are responsible
for all transportation and insurance charges for the unit to
and from the Authorized Service Station. If you live in the
U.S.A. you may, at your option, return your DVD Unit to:
Toshiba America Consumer Products Inc.
Returns Center
1420C Toshiba Dr.
Lebanon, TN 37087
Upon receipt we will, at our option, exchange the DVD Unit
with a new or refurbished unit. Canadian Consumers are
requested to contact TCL. In Hawaii consumers are
requested to contact THI.
Commercial Units
Products sold and used for commercial use have a limited
ninety (90) day warranty for all parts and labor.
(Continued)
45
Others
LIMITED WARRANTY DVD VIDEO PLAYER (continued)
How to Obtain Warranty Service
(1) Refer to the troubleshooting guide in your owner’s manual. This check list may solve your problem.
(2) In the U.S.A., only call the TACP toll free number 800-631-3811, or if in Hawaii or Canada see listing below within (30)
days after you find a defective product or part.
(3) Arrange for the delivery of the product to the TACP/THI/TCL Authorized Service Station or TACP Return Center.
Products shipped to the Service Station must be insured and safely and securely packed, preferably in the original
shipping carton, and a letter explaining the defect and also a copy of the bill of sale or other proof of purchase must be
enclosed.
In the Continental United States contact:
Toll Free
800-631-3811
In Hawaii contact:
Toshiba Hawaii Inc.
327 Kamakee Street
Honolulu, HA 96814
(808)-521-5377
In Canada contact:
Consumer Electronics Group
191 McNabb Street
Markham, Ontario L3R 8H2
(905)-470-5400
Consumer Electronics Group
22171 Fraserwood Way
Richmond, B.C. V6W 1J5
(604)-303-2500
Consumer Electronics Group
1643 North Service Road
Droval, QC H9P 1J1
(514)-856-4100
All warranties implied by state law, including the implied warranties of merchantability and fitness for a particular purpose, are
expressly limited to the duration of the limited warranties set forth above. With the exception of any warranties implied by state
law as hereby limited, the foregoing warranty is exclusive and in lieu of all other warranties, guarantees, agreements and
similar obligations of manufacturer or seller with respect to the repair or replacement of any parts. In no event shall TACP/THI
be liable for consequential or incidental damages.
No person, agent, distributor, dealer or company is authorized to change, modify or extend the terms of these warranties in
any manner whatsoever. The time within which an action must be commenced to enforce any obligation of TACP/THI arising
under the warranty or under any statute, or law of the United States or any state thereof, is hereby limited to ninety (90) days
from the date you discover or should have discovered, the defect. This limitation does not apply to implied warranties arising
under state law.
This warranty gives you specific legal rights and you may also have other rights which may vary from state to state. Some
states do not allow limitation on how long an implied warranty lasts, when an action may be brought, or the exclusion or
limitation of incidental or consequential damages, so the above provisions may not apply to you.
ATTENTION CANADIAN CONSUMERS:
Canadian consumers are requested to complete the special Canadian “Warranty Registration Form” enclosed, and forward
this completed form with a copy of bill of sale to TOSHIBA OF CANADA to “Register and Validate” their warranty. Product
must be purchased from an Authorized Canadian Dealer. Products purchased in the U.S.A. and used in Canada are not
covered by these warranties.
IMPORTANT: PACKING AND SHIPPING INSTRUCTION
When you send the product to a Service Station, you must use the original carton box and packing material, then insert the
original carton box containing the unit into another carton using more packing material.
46
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement