Panasonic PV-D4754S DVD-VCR Combo User manual

DVD/VCR DECK

Operating Instructions

Model No.

PV-D4754S

Connections and Initial Setup Procedures are on pages 12 to 17.

MULTI FORMAT PLAYBACK

*

Ability to play back may depend on recording conditions.

As an

E

NERGY

S

TAR Partner, Matsushita Electric Corporation of America has determined that this product or product model meets the

E

NERGY

S

TAR guidelines for energy efficiency.

Please read these instructions carefully before attempting to connect, operate or adjust this product. Please save this manual.

Spanish Quick Use Guide is included.

(Guía para rápida consulta en español está incluida.)

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

D4754S P1-25 (040202).p65

1 2004/02/02, 13:22

Important Safeguards and Precautions

TO REDUCE THE RISK OF ELECTRIC SHOCK, FIRE, INJURY TO PERSONS OR DAMAGE TO

THIS PRODUCT, READ AND RETAIN ALL SAFETY AND OPERATING INSTRUCTIONS. HEED ALL

WARNINGS IN THE MANUAL AND ON THE PRODUCT.

INSTALLATION

1 POWER SOURCE CAUTION

Operate only from a power source indicated on the unit or in this manual. If necessary, have your Electric Utility Service

Company or Video Products Dealer verify the power source in your home.

2 POLARIZED OR GROUNDING PLUG

As a safety feature, this product comes with either a polarized power cord plug (one blade is wider than the other), or a threewire grounding type plug.

POLARIZED PLUG CAUTION:

This plug will only fit into an outlet one way. If you cannot fully insert the plug, try reversing it. If it still will not fit, have an electrician install the proper wall outlet. Do not defeat the safety feature by tampering with the plug.

GROUNDING PLUG CAUTION:

This plug will only fit into a three-hole grounding outlet. If necessary, have an electrician install the proper outlet. Do not defeat the safety feature by tampering with the plug.

3 POWER CORD

Make sure power cords are routed so that they are not likely to have anything rest on them, roll over them, or be in the way of walking traffic. If an extension cord is used, make sure it also has either a polarized or grounded plug and that the cords can be securely connected. Frayed cords, damaged plugs, and damaged or cracked wire insulation are hazardous and should be replaced by a qualified service technician.

Overloaded outlets and extension cords are fire hazards and should be avoided.

4 DO NOT BLOCK VENTILATION HOLES

Ventilation openings in the cabinet release heat generated during operation. If they are blocked, heat build-up inside the unit can cause failures that may result in a fire hazard or heat damage to cassettes or discs.

For protection, follow these rules: a. Never cover ventilation slots or the unit while in use, or operate the unit when placed on a bed, sofa, rug, or other soft surface.

b. Avoid built-in installation, such as a book case or rack, unless proper ventilation is provided.

5 PLACEMENT: AVOID EXTREMELY HOT LOCATIONS OR

SUDDEN TEMPERATURE CHANGES

Do not place the unit over or near heater or radiator, in direct sunlight, inside closed vehicles, in high temperature [over 104°F

(40°C)], or in over 75% humidity. If the unit is suddenly moved from a cold place to a warm one, moisture may condense in the unit and on the tape causing damage. Never subject the unit to vibration, impact, or place it so that the surface is tilted as internal parts may be seriously damaged.

6 TO AVOID PERSONAL INJURY

• Do not place unsecured equipment on a sloping surface.

• Do not place this unit on any support that is not firm, level, and adequately strong.

The unit could fall causing serious injury to a child or adult and damage to the unit.

• An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

• Carefully follow all operating instructions and use the manufacturer's recommended accessories when operating this unit or connecting it to any other equipment.

OUTDOOR ANTENNA INSTALLATION

1 SAFE ANTENNA AND CABLE CONNECTION

If an outside antenna or cable system is connected to the equipment, be sure the antenna or cable system is grounded so as to provide some protection against built up static charges and voltage surges.

Section 810 of the National

Electrical Code, ANSI/NFPA 70

NEC

- NATIONAL

ELECTRICAL CODE

ANTENNA

LEAD IN

WIRE

GROUND

CLAMP

(in Canada, part 1 of the Canadian Electrical

Code) provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an

ELECTRIC

SERVICE

EQUIPMENT

antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

electrodes and requirements for the grounding electrode.

2 KEEP ANTENNA CLEAR OF HIGH VOLTAGE POWER LINES OR

CIRCUITS

An outside antenna system should be located well away from power lines, electric light or power circuits and where it will never come into contact with these power sources if it should happen to fall. When installing an outside antenna, extreme care should be taken to avoid touching power lines, circuits or other power sources as this could be fatal. Because of the hazards involved, antenna installation should be left to a professional.

USING THE UNIT

If the unit has been in storage or moved to a new location, refer first to the

INSTALLATION section of these safeguards.

1 KEEP THE UNIT AWAY FROM WATER OR MOISTURE OF ANY KIND.

2 IF EQUIPMENT IS EXPOSED TO RAIN, MOISTURE, OR STRONG

IMPACT, unplug the unit and have it inspected by a qualified service technician before use.

3 DURING AN ELECTRICAL STORM

During a lightning storm, whether indoors or outdoors, or before leaving the unit unused for extended periods of time, disconnect all equipment from the power source as well as the antenna and cable system.

4 WHEN THE UNIT IS PLUGGED IN

• Never expose the unit to rain or water. DO NOT OPERATE if liquid has been spilled into the unit. Immediately unplug the unit, and have it inspected by a service technician. Fire and shock hazards can result from electrical shorts caused by liquid contact inside.

• Never drop or push any object through openings in the unit. Some internal parts carry hazardous voltages and contact can cause electric shock or fire hazard.

Do not put any foreign object on the disc tray.

• Avoid placing the unit directly above or below your TV set as this may cause electrical interference. Keep all magnets away from electronic equipment.

5 USING ACCESSORIES

Use only accessories recommended by the manufacturer to avoid risk of fire, shock, or other hazards.

6 CLEANING THE UNIT

Unplug the unit. Then, use a clean, dry, chemically untreated cloth to gently remove dust or debris. DO NOT USE cleaning fluids, aerosols, or forced air that could over-spray, or seep into the unit and cause electrical shock. Any substance such as wax, adhesive tape, etc. may mar the cabinet surface. Exposure to greasy, humid, or dusty areas may adversely affect internal parts.

SERVICE

1 DO NOT SERVICE THIS PRODUCT YOURSELF

If, after carefully following the detailed operating instructions, this product does not operate properly, do not attempt to open or remove covers, or make any adjustments not described in the manual. Unplug the unit and contact a qualified service technician.

2 IF REPLACEMENT PARTS ARE REQUIRED

Make sure the service technician uses only parts specified by the manufacturer, or those having the same safety characteristics as the original parts. The use of unauthorized substitutes may result in fire, electric shock, or other hazards.

3 HAVE THE SERVICE TECHNICIAN PERFORM A SAFETY CHECK

After any service or repairs to the unit, request the service technician to conduct a thorough safety check as described in the manufacturer’s service literature to ensure that the unit is in safe operating condition.

2

D4754S P1-25 (040202).p65

2 2004/02/02, 13:22

Safety Precautions/Mesures de sécurité

To prevent fire or shock hazard, do not expose this equipment to rain or moisture.

To prevent electric shock, match wide blade of plug to wide slot, fully insert.

AVERTISSEMENT:

Afin de prévenir tout risque d’incendie ou de chocs électriques, ne pas exposer cet appareil à la pluie ou à une humidité excessive.

ATTENTION :

Pour éviter les chocs électriques, introduire la lame la plus large de la fiche dans la borne correspondante de la prise et pousser jusqu’au fond.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

This symbol warns the user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any inside part of this unit.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included.

Therefore, it should be read carefully in order to avoid any problems.

CAUTION:

UNIT IS A CLASS I LASER PRODUCT.

HOWEVER THIS UNIT USES A VISIBLE LASER BEAM WHICH COULD

CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED.

BE SURE TO OPERATE THE UNIT CORRECTLY AS INSTRUCTED.

WHEN THIS UNIT IS PLUGGED TO THE WALL OUTLET, DO NOT PLACE

YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY AND OTHER

OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN

HAZARDOUS RADIATION EXPOSURE.

DO NOT OPEN COVERS AND DO NOT ATTEMPT TO REPAIR YOURSELF.

REFER SERVICING TO QUALIFIED PERSONNEL.

CAUTION:

LASER RADIATION

WHEN OPEN DO NOT

STARE INTO BEAM.

ATTENTION:

RAYONNEMENT

LASER EN CAS

D’OUVERTURE.

NE PAS REGARDER

DANS LE FAISCEAU.

(Inside of product)

FCC NOTE:

This equipment has been tested and found to comply with part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when operated in a residential environment. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, use the equipment in another location and/or utilize an electrical outlet different from that used by the receiver.

If necessary, consult the dealer or an experienced radio/TV technician for help. The user may find the booklet, “Something About Interference” available from FCC local regional offices helpful.

FCC Caution:

To assure continued compliance, (example- use only shielded interface cables when connecting to other devices.) Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

Region Management Information:

This DECK is designed and manufactured to respond to the

Region Management Information that is recorded on a DVD disc. If the Region number described on the DVD disc does not correspond to the Region number of this DECK, this

DECK cannot play this disc.

●The Region number for this DECK is “1”.

●The Player will play DVD-Video marked with labels containing “1” or “ALL”.

Example:

1

ALL

1

2

4

3

D4754S P1-25 (040202).p65

3 2004/02/02, 13:22

Before Using

Congratulations

on your purchase of one of the most sophisticated and reliable products on the market today. Used properly, it will bring you years of enjoyment. Please fill in the information below. The serial number is on the tag located on the back of your DECK.

• Date of Purchase

• Dealer Purchased From

• Dealer Address

• Dealer Phone No.

• Model No. PV-D4754S

• Serial No.

Head Cleaning

Playing older or damaged tapes may eventually cause video heads to become clogged.

Video Head Clog Sensor

During playback, this screen appears if clogging is detected.

To remove screen, press PLAY on the remote or DECK.

V I DEO HEADS MAY

NEED CLEAN I NG

PLEASE I NSERT HEAD

CLEAN I NG CASSETTE

OR REFER TO MANUAL

END : PLAY

Accessories

Remote Control

EUR7724KB0

Batteries 2 “AA”

• Use “dry” type head cleaning cassette only.

(Part No. NV-TCL30PT is recommended.)

• Follow cleaning tape instructions carefully.

Excessive use of tape can shorten head life.

• If head clog symptoms persist, contact your nearest servicenter by visiting our Web Site

(see p. 61).

Cleaning DECK

RF Coaxial Cable

LSJA0418

To order accessories, call toll free

1-800-332-5368.

Use a soft cloth or dusting attachment of a vacuum cleaner to remove dust from the ventilation holes on the back sides and bottom of the cabinet.

Plastic surfaces are easily scratched and can be marred by alcohol and various solvents.

Avoid excessive use of oil-based furniture polishes since the materials used in the cabinet will accumulate more dust. We recommend using a non-abrasive, antistatic cleaner and polisher.

Loading the Batteries

1) Open cover.

2) Insert batteries as marked.

3) Close cover.

Battery replacement caution

• Do not mix old and new batteries.

• Do not mix alkaline with manganese batteries.

Features for a Quality Picture (VCR)

Digital Auto Picture

Automatically controls the video output signal for less noise depending on the tape condition.

Digital Auto Tracking

Continuously analyzes the signal and adjusts for optimum picture quality.

Manual Tracking Control

(to reduce picture noise)

Use during Playback and Slow Motion mode to reduce picture noise.

Press CH (TRACKING) / on the remote control or on DECK until the picture clears up.

To return to Auto Tracking, press POWER off, then on again a few seconds later.

Record/ Playback Time

Only use tapes with the mark in this DECK.

Tape Speed

Setting

Type of Video Cassette

T120 T160 T180

R

R

R

R

R

R

R

R SP

(Standard Play)

2 Hours

2 Hours

40 Minutes

3 Hours

4

SLP

(Super Long Play)

6 Hours 8 Hours 9 Hours

V-Lock Control (to reduce picture jitter)

In Still mode, CH (TRACKING) / operate as a

V-Lock control.


D4754S P1-25 (040202).p65

4 2004/02/02, 13:22

Table of Contents

Initial Setup (Connection)

DVD / VCR

Important Safeguards and Precautions ......................... 2, 3

Before Using ......................................................................... 4

DECK & Cassette Information ........................................ 6 , 7

Location of Controls .................................................... 8 ~ 10

Displays

(On Screen Displays and Multi Function Display) .................

11

Connections ............................................................... 12 ~ 15

Initial Setup for Basic Connections

(Ready to Play)

....... 16, 17

Basic Operation

VCR

Reset Language, Channels, Clock, VCR’s Output Channel .. 18, 19

Playback/ Record on a Tape........................................ 20, 21

DVD

Basic DVD Operation ................................................... 22, 23

VCR Operation

Timer Recording ........................................................... 24, 25

MTS Broadcast/ VHS Hi-Fi Stereo System ................. 26, 27

Multi-Brand Control Feature ........................................ 28, 29

Tape Operation

(Search System)

...................................... 30, 31

Special VCR Features ................................................ 32 ~ 34

Copying Your Tapes

(Dubbing) ......................................................

35

DVD Operation

Disc Operation ............................................................ 36 ~ 41

DVD-RAM Operation

(DVD-RAM only)

.............................. 42, 43

DVD Operation using On-Screen Displays .............. 44 ~ 48

MP3/JPEG Playback Operation ................................. 49 ~ 51

Settings for DVD Operation ....................................... 52 ~ 55

A/V OPTIMIZER ................................................................... 55

Language Code List ........................................................... 56

For Your Information

Warning and Instruction Displays ..................................... 57

Before Requesting Service .......................................... 58, 59

Limited Warranty .......................................................... 60, 61

Customer Services Directory ............................................ 61

Spanish (Español) Quick Use Guide ......................... 62 ~ 69

Index .............................................................................. 70, 71

5

D4754S P1-25 (040202).p65

5 2004/02/02, 13:22

DECK & Cassette Information

Prevent Accidental Tape Erasure

Break off the tab to prevent recording.

Record Tab

Screw driver

To record again

Cover the hole with cellophane tape.

DVD-RAM discs

DVD-RAM discs must meet the following conditions for this unit to be able to play them.

Type

Capacity

• Non-cartridge discs

• Discs that can be removed from their cartridges (TYPE 2 and 4)

• 12 cm (5”) 9.4 GB (double-sided) and 4.7 GB (single-sided)

• 8 cm (3”) 2.8 GB (double-sided)

• Remove TYPE 2 and 4 discs from their cartridges before use, then return them when you are finished.

Read the instructions for the disc carefully.

Disc formats supported by this DECK

DECK can play back discs bearing any of the following marks:

Logo Disc type

DVD-RAM (Version 1.1 of the

Video Recording Format a unified video recording standard)

DVD (DVD-Video)

DVD-R (DVD-Video formatted discs [finalized])

DVD-Audio

CD (CD-DA)

• Some parts of the disc, for example where one program ends and another begins, may not play smoothly.

Disc Handling

Handling precautions

• Sticking a label on the disc may impair DVD-R playback.

• Do not attach sticker to discs. (Do not use discs with exposed adhesive from tape or left over peeled-off stickers.)

• Only hold disc by edges as shown below. Fingerprints, dirt and scratches can cause skipping and distortion.

• Do not write on label side of disc.

• Never use record cleaning sprays, benzine, thinner, static electricity prevention liquids, or any other solvent.

Disc tray

Disc

CD-R/CD-RW

• CD-DA format

• WMA/MP3/JPEG file and

finalized.*

[Discs Played 8cm (3") or 12cm (5")]

*A process that allows play on compatible equipment.

Discs which cannot be played

• DVD with Region No. other than “1” or “ALL”

• PAL discs (the audio on DVD-Audio can be played), DVD-ROM, DVD-RW, DVD+R,

DVD+RW, CD-ROM, CDV, CD-G, CVD, SVCD,

SACD, CD-TEXT, Divx Video Disc, Photo-CD and Video CD

Notes

• Do not use irregularly shaped discs (e.g. heartshaped), as these can damage the unit.

• It may not be possible to play CD-R, CD-RW,

DVD-R and DVD-RAM in all cases due to the type of disc or condition of the recording.

• Do not try to close disc tray when disc is not properly placed.

To clean disc surface

With a soft, damp (water only) cloth, gently wipe from the center hole to the outer edge as shown below. (Wiping in a circular pattern will scratch the surface.)

• DVD-RAM, DVD-R :

Clean only with the DVD-RAM disc cleaner available. Never use cloths or cleaners for CDs etc.

If disc is brought from a cold to a warm environment, moisture may form on the disc

Wipe away moisture with a soft, dry, lint-free cloth before using disc. (See above.)

Improper disc storage

Discs could be damaged if stored or left in areas:

• exposed to direct sunlight.

• that are humid or dusty.

• near heat (i.e. heater, radiator, etc.).

6


D4754S P1-25 (040202).p65

6 2004/02/02, 13:22

Specifications

Power Source:

Power Consumption:

120 V AC, 60 Hz

Power On: Approx. 28 watts, Power Off: Approx. 0.85 watts

Video Signal:

EIA Standard NTSC color

Video Recording System:

4 rotary heads helical scanning system

1 track (Normal), 2 channel (Hi-Fi Audio Sound)

Audio Track:

Tuner

Broadcast Channels:

CABLE Channels:

VHF 2 ~ 13, UHF 14 ~ 69

Midband A through I (14 ~ 22), Superband J through W (23 ~ 36)

Hyperband AA ~ EEE (37 ~ 64), Lowband A-5 ~ A-1 (95 ~ 99)

Special CABLE channel 5A (01), Ultraband 65 ~ 94, 100 ~ 125

Input/Output Terminal:

Input Terminal:

Output Terminal:

Audio/Video Line Input/Output, RF Input/Output

Audio/Video Line Input (Front)

S-Video Output (DVD only), Component Video Output (DVD only)

Audio Output 2 (L), (R)

Operating Temperature:

Operating Humidity:

Weight:

Dimensions:

5 °C ~ 40 °C (41 °F ~ 104 °F)

10 % ~ 75 %

3.85 kg (8.5 lbs).

430 (W) x 95 (H) x 273 (D) mm

16-15/16” (W) x 3-3/4” (H) x 10-3/4” (D) inch

Discs Played

(1) DVD-Video Disc

DVD-Audio Disc

DVD-RAM Disc

(2) Compact Disc

(CD-DA)

(CD-R/CD-RW, MP3, WMA, JPEG)

5” (12 cm) single-sided single-layer

5” (12 cm) single-sided double-layer

5” (12 cm) double-sided double-layer (one layer per side)

3” (8 cm) single-sided single-layer

3” (8 cm) single-sided double-layer

3” (8 cm) double-sided double-layer (one layer per side)

5” (12 cm) 9.4 GB (double-sided) and 4.7 GB (single-sided)

3” (8 cm) 2.8 GB (double-sided)

5” (12 cm) disc

3” (8 cm) disc

Digital Audio Output:

Pickup:

Digital Optical Connector

Wavelength: 655 nm (DVD), 790 nm (CD)

Laser power: CLASS II

Note:

•

Designs and specifications are subject to change without notice.

Definition of Terms (DVD)

Angle:

Some DVD discs feature scenes simultaneously shot from different angles.

The ANGLE button can be used to view the scene from different angles.

(ANGLE Indicator lights on DECK when a scene recorded at different angles is detected.)

Chapter Number: Titles are subdivided into numbered sections. You can quickly search for a favorite scene using these numbers.

DVD:

A high-density optical disc on which high-quality pictures and sound have been digitally recorded. DVD incorporates video compression technology

Subtitles:

(MPEG II) and high-density recording technology which allow entire movies to be recorded with incredible playback quality.

Written dialogue which appears at the bottom of the screen.

Time Number:

The elapsed play time from the start of a disc or title. Use to quickly find scenes. (May not work with some discs.)

Title Number:

For DVD discs with two or more titles, the title is numbered as title 1, title 2, etc.

Track Number:

Numbers assigned to tracks on CDs to allow specific tracks to be quickly located.

Apparatus Claims of U.S. Patent Nos. 4,631,603, 4,577,216, 4,819,098 and 4,907,093, licensed for limited viewing uses only.

This product incorporates copyright protection technology that is protected by method claims of certain U.S. Patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision

Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

7

D4754S P1-25 (040202).p65

7 2004/02/02, 13:22

Location of Controls

Remote Control

EJECT

/

OPEN / CLOSE

pp. 20, 22

POWER

NUMBER keys

ADD/DELETE

/ CLEAR

pp. 19,

39

ACTION pp. 18

, 52

SET

VCR mode p. 28

STOP

pp. 20, 22

REWIND

/ SEARCH /

SLOW

-

pp. 20, 23

FAST FORWARD

/

SEARCH / SLOW+

pp. 20, 23

PAUSE

/ STILL

pp. 20, 23

ANGLE

p

. 37

SUB TITLE

p

. 36

TITLE /

DIRECT NAVIGATOR

p

. 38, 42

Bold: VCR Function / Bold Italic: VCR and DVD Functions

Italic: DVD Function / Normal: Others

VCR/TV p. 21

TV mode

p. 28

CHANNEL

TRACKING

/

V-LOCK

/ /

/

10

pp. 4, 21,

22

VOLUME

+

/

-

p. 28

MENU / PLAY LIST

p

. 38, 43

SELECT

DVD mode

p. 28

PLAY

pp. 20, 22

SKIP+

SKIP-

p

. 23

Virtual Surround Sound (V.S.S.) /

ENTER

pp

. 23, 28

ZOOM

p

. 37

TAPE POSITION

/

STATUS

VOLUME ADJUST

p. 31,

40

AUDIO (SAP / Hi-Fi)

pp. 27,

36

INPUT p. 35

DISPLAY

p. 11, 44

RETURN / SEARCH

pp

. 22, 30

COMMERCIAL SKIP

/

ZERO SEARCH

A/V OPTIMIZER

pp. 30,

55

RECORD p. 21

COUNTER RESET p. 30

SPEED p. 21,

41

/

PAGE

EJECT button: When this button is pressed in VCR mode, the tape is ejected.

This button is inoperative if pressed during recording.

If pressed in DVD mode, the disc tray opens or closes.

PROGRAM p. 24

8


D4754S P1-25 (040202).p65

8 2004/02/02, 13:22

Bold:

VCR Function

Italic: DVD Function

Bold Italic: VCR and DVD Functions

Normal: Others

PLAY p. 20

If the disc cannot be removed...

First, unplug DECK. Then, prepare a rigid wire (e.g. an extended paper clip) and, applying moderate force, insert it straight into the hole at the base of the tray.

The tray will eject a little. Now, pull the tray all the way out and remove the disc.

STOP/EJECT p. 20

Over 2 inches

Remote

Sensor

POWER

Cassette

Compartment

Disc Tray

Audio/Video

Input Connector 2

(LINE 2)

p. 35

REC p. 21

CHANNEL /

TRACKING/V-LOCK pp. 4, 21

Blue Light

p. 32

Multi Function

Display

p. 11

OPEN/CLOSE

p.

22

FAST FORWARD

/ SEARCH /

SKIP

p.

20, 23

REWIND

/ SEARCH /

SKIP

p.

20, 23

PLAY

p.

22

STOP

p.

22

Reset All Memory Functions

Returns to factory setting. Use if relocating DECK, or if Initial Setup needs to be redone.

• Make sure a tape is not inserted in the DECK.

1 2

1

2

3

Turn DECK Power on.

Press and hold both VCR PLAY and CHANNEL on the DECK for more than 5 seconds.

• The power shuts off.

Perform “Initial Setup (Ready to Play)” on page 16.

9

D4754S P1-25 (040202).p65

9 2004/02/02, 13:22

Location of Controls (continued)

Rear View of DECK

AC Power Plug

• While plugged into an AC outlet, this DECK consumes 0.85 W of electrical power in off mode.

Bold:

VCR Function

Bold Italic: VCR and DVD Functions


VHF/UHF Antenna Output Terminal p.12

VHF/UHF Antenna Input Terminal p. 12

Component Video Output

Connector (Y, P

B

, P

R

)

(DVD Only)

p.

13

Video Output

Connector p.

12

Video Input

Connector p. 35

• • •

Optical Digital Audio

Output Connector

(DVD Only)

p.

15

S-Video Out Connector

(DVD Only)

pp.

10, 13

Audio Output 1

Connector (L/R) p.

12

Audio Output 2

Connector (L/R) p.

13

Audio Input

Connector (L/R) p. 35

The following table shows the status of the output jacks when in VCR or DVD mode.

VCR

DVD

Video Output

Audio Out 1

Audio Out 2

YES

YES

Component

Video Output

N/A

YES

S-VIDEO OUT

N/A

Note

• PROG functions on the remote are not available when using Component Video Output and

S-VIDEO OUT. Please set TV to either RF INPUT or VIDEO INPUT, and then press PROG.

To enjoy PROGRESSIVE SCAN video

(1). Connect Component Video Output to the component video input terminals of a television.

(See p. 13.)

(2). When PROGRESSIVE OUT is set to “ON” in the DVD Main Menu (p. 55), a Progressive

Scan signal is output from the Component Video Output Connector.

Notes

• The screen may shift off-center when using progressive output. Please adjust the screen position if this occurs. (Refer to your TV manual.)

• If the television is not progressive compatible, a progressive scan picture is not available.

Connect the Video Output or S-Video Output connector (see p. 12, 13) and set PROGRESSIVE OUT to “OFF” in the DVD Main Menu. (See p. 55.)

10


D4754S P1-25 (040202).p65

10 2004/02/02, 13:22

Displays (On Screen & Multi Function)

On Screen Displays (VCR)

Function & Channel Displays

CH 0 8

When a function button is pressed, e.g. PLAY, or you change channels, a 5-second display appears.

Blank Tape/ No Video Signal

Indications

Whenever a blank section of a tape comes up in Play mode, or when the selected channel has no broadcast signal with Weak

Signal Display Feature (p. 33) set to OFF, the TV screen will turn solid blue.

Current Time

Function Status

VCR Status & Clock Displays

To display or remove screen shown at right,

Rec Time Remaining

(OTR mode only, see p. 21.)

REW 1 2 : 0 0AM

0 : 25

CH 02

-0 : 1 2 : 3 4

SP

STEREO

SAP

MONO

Channel

Counter

Broadcast Audio

Being Received

(See pp. 26, 27.)

Tape Speed

(See p. 4.)

Multi Function Display

VCR mode Indicator

Lights up when

DECK is in VCR mode.

Tape Indicator

Lights up when a tape is inserted.

DISC Indicator

Lights up when a disc is inserted.

VCR REC Indicator

Lights up during recording.

Timer Indicator

Lights up when

DECK is set for

Timer Recording, or when One

Touch Recording

(OTR) is used.

Flashes when

Timer Recording is set, but a tape has not been inserted into DECK and when a power interruption occurs during Timer

Programming.

Hi-Fi Indicator

Lights up when

Hi-Fi audio is present in Play mode.

AM/PM

Indicator

DVD mode Indicator

Lights up when

DECK is in DVD mode.

CD/MP3/WMA

Indicator

CD : Lights when an

Audio CD is inserted or

JPEG file is played.

MP3/WMA :

Lights when an

MP3 or WMA file is played.

ANGLE Indicator

Lights up when a scene recorded at different angles is detected.

(See p. 37.)

(DVD only)

DTS Indicator

Lights up when a DTS formatted DVD is played.

(DVD only)

V C R

TIMER REC

Hi - Fi

C D

DVD

MP3 WMA

ANGLE

AM

PM

Dolby Digital

Indicator

Lights up when a “Dolby Digital” formatted DVD is played.

(DVD only)

Clock/ Status/ Channel/ Speed Display

Displays current time. Briefly displays DECK status when you press a function button, channel number or “L1” or “L2” when you select channel or line input, and recording speed when you press SPEED.

11

D4754S P1-25 (040202).p65

11 2004/02/02, 13:22

Connections

Basic Connections

•

•

If your TV has AUDIO and VIDEO IN terminals, connect them to DECK for higher quality picture and sound.

You can enjoy stereo sound even if your TV is not stereo by connecting a stereo amplifier to DECK.

• Connect DECK and TV with an RF Coaxial Cable

a

(supplied) or an AV Cable

b

(not supplied) as shown in the figure below.

Antenna or Cable

DSS

Receiver

IN

IN

OUT

IN

OUT

Cable Box

DVD/VCR DECK

VIDEO

OUT

L

AUDIO

R

IN 1

IN FROM ANT.

VHF/UHF

OUT TO TV

or

1

Disconnect antenna or cable from TV and connect to DECK.

2

Connect DECK to TV with RF Coaxial Cable.

TV

a

RF COAXIAL CABLE

(supplied)

AUDIO IN

R L

VIDEO

IN

VHF/

UHF

b

AV CABLE

(not supplied)

When using “Nut type” RF coaxial cables, tighten with fingers only. Overtightening may damage terminals.

Note to CABLE system installer

This reminder is provided to call the CABLE system installer’s attention to Article 820-40 of the

NEC in USA (and to the Canadian Electrical Code in Canada) that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

12


D4754S P1-25 (040202).p65

12 2004/02/02, 13:22

Other Connections

DVD/VCR DECK

OUT IN 1

IN FROM ANT.

VHF/UHF

OUT TO TV

ANT or CATV

Cable Box

IN OUT

Connect With Two Cable Boxes

DVD/VCR DECK

ANT

IN FROM ANT.

Cable Box

OUT IN 1

or

CATV

IN OUT

2-Way Splitter

OUT 1 OUT 2

Cable Box

IN OUT

TV

VHF/

UHF

IN

R

OUT

AUDIO

L

VIDEO

VHF/UHF

OUT TO TV

A/B Switch

IN 1 IN 2

You Can

• view any

(including scrambled) channel.

• use Remote

Control to select channels without using Multi-brand control feature.

You Cannot

• record scrambled channels.

You Can

TV

IN

R

OUT

AUDIO

L

VIDEO

VHF/

UHF

• record and view both scrambled and unscrambled channels if additional equipment is added.

This connection requires: two converter boxes, an A/B switch, and a 2-way splitter.

You Cannot

• view a channel other than the one selected for any type of recording.

• set a Timer recording of a channel unless you select it on the Cable Box.

Connections For DVD Only (enjoying higher picture quality)

1

2

3

Connect AUDIO OUT2 (L, R) to the AUDIO IN (L, R) of the TV. (audio input for COMPONENT or S-VIDEO mode).

If your TV has COMPONENT VIDEO INPUT, connect to COMPONENT VIDEO OUT.

If your TV does not have COMPONENT VIDEO INPUT but has S-VIDEO INPUT, connect to

S-VIDEO OUT.

When in DVD mode, set your TV to either COMPONENT VIDEO IN or S-VIDEO IN.

Notes

• You can watch DVDs through the S-VIDEO or COMPONENT VIDEO, VHF/UHF OUT TO TV,

and VIDEO OUT connections to your TV. The VCR and TUNER pictures are available only from the VIDEO OUT and VHF/UHF OUT TO TV connections to your TV.

• PROG functions on the remote are not available when using S-VIDEO OUT and COMPONENT

Video Output. Please set TV to either RF INPUT or VIDEO INPUT, and then press PROG.

• TV must have capability to accept and display a progressive scan signal to use

PROGRESSIVE mode. Consult your TV operating instructions.

DVD/VCR DECK

TV

From DECK’s

A/V OUTPUT

DVD OUTPUT

COMPONENT

VIDEO OUT AUDIO OUT2

IN

IN

IN

Y

Y

AUDIO

PB

P

B

L

VIDEO

S-VIDEO OUT

PR

P

R

R

S-VIDEO

IN

or

13

D4754S P1-25 (040202).p65

13 2004/02/02, 13:22

Connections (continued)

Audio Connections

Ready Checklist

Turn down the volume, then turn DECK, as well as other equipment to be connected, off before proceeding with connection.

Do not block ventilation holes of any of the equipment and arrange them so that air can circulate freely.

Read through the instructions before connecting other equipment.

Ensure that you observe the color coding when connecting audio and video cables.

■ Connecting Amplifier (2ch stereo system)

Speaker

DVD/VCR DECK

AUDIO OUT2

L

R

Amplifier

AUDIO IN

R L

Speaker

Enjoying digital audio output from the digital audio output connector

Notes on audio output from the optical digital audio output connector

Disc

DVD

DVD-RAM

CD

MP3

WMA

Sound recording format

Dolby Digital

Linear PCM

(48/96/192/44.1/88.2/

176.4 kHz 16/20/24bit)

DTS

Dolby Digital

Linear PCM(48 kHz/16 bit)

Linear PCM

MP3

WMA

Optical digital audio output from connector

Dolby Digital bitstream (1-5.1 ch) or PCM (48 kHz sampling/16 bit only)* 1

Linear PCM (2 ch)

(48 kHz sampling/16 bit or 44.1 kHz sampling/

16 bit)*

2

Bitstream or PCM (48 kHz sampling/16 bit only)*

1

Dolby Digital bitstream (1 - 5.1 ch) or PCM (48 kHz sampling/16 bit only)

Linear PCM (2 ch)

Linear PCM (44.1 kHz sampling)

Linear PCM (It depends on the MP3 file)

Linear PCM (It depends on the WMA file)

*1 The type of audio output from the connector can be selected by the Settings for DVD

Operation. (See p. 53.)

*2 When “LPCM(DVD)” is set to OFF in the DVD Main Menu, 44.1 or 48 kHz sampling/16 bit is ouput. When set to ON, sampling of sound quality greater than 44.1 or 48 kHz/16 bit is reduced to 44.1 or 48 kHz/16 bit. (See page 53.)

For your reference:

• Dolby Digital is a digital sound compression technique developed by the Dolby Laboratories

Licensing Corporation. Supporting 5.1-channel surround sound, as well as stereo (2-channel) sound, this technique enables a large quantity of sound data to be efficiently recorded on a disc.

• Linear PCM is a signal recording format used in CDs. While CDs are recorded in 44.1 kHz/16 bit,

DVDs are recorded in 44.1 kHz/16 bit ~ 192 kHz/24 bit.

• If you have a Dolby Pro Logic Surround decoder, you will obtain the full benefit of Pro Logic from the same DVD movies that provide full 5.1 channel Dolby Digital soundtracks, as well as from titles with the Dolby Surround mark. For information on Panasonic or Technics Dolby Pro Logic

Surround Sound Decoders please contact your local dealer.

14


D4754S P1-25 (040202).p65

14 2004/02/02, 13:22

■ Connecting Amplifier (5.1 ch Surround system) [Digital connection]

DECK Dolby Digital Decoder Amplifier Speaker

or

DECK DTS (Digital Theater Systems) Decoder Amplifier Speaker

When DVDs recorded in Dolby Digital or DTS are played, Dolby Digital bitstream or DTS bitstream is output from the DECK OPTICAL digital audio output connector.

When DECK is connected to a Dolby Digital decoder or DTS decoder, you can enjoy theater-quality audio in your home. [An optical digital audio cable (optional) is required when an optional Dolby Digital decoder or DTS decoder is used.]

Notes on connecting an optical

digital audio cable (optional)

• Firmly connect the cable to the connector.

Surround

Speaker

[5.1ch Surround system]

Surround

Speaker

Center

Speaker

DVD/VCR DECK

(Rear)

Decoder with

Dolby Digital /DTS processing (optional)

Front

Speaker

Front

Speaker

Optical Digital

Audio Cable

(optional)

To Optical

Digital Audio

Input Connector

Amplifier

Subwoofer

Caution for optical digital audio output connector:

• When connecting an amplifier (with an Optical Digital Input Connector) which does not contain the Dolby Digital or DTS decoder, be sure to select “PCM” at “Dolby Digital” and “PCM” at “dts” of the Settings for DVD Operation “Audio Output” (see p. 53).

Otherwise, any attempt to play DVDs may cause such a high level of noise that it may be harmful to your ears and damage your speakers.

• When a Dolby Digital/DTS decoder is connected, please select “Bitstream” at “dts” or

“Dolby Digital” of the Settings for DVD Operation “Audio Output”.

If “PCM” is selected, there will be stereo sound. (See p. 53.)

• CDs can be played as usual.

Note:

• Some DTS decoders which do not support DVD-DTS interface may not work properly with DECK.

Manufactured under license from Digital Theater Systems, Inc. US Pat. No’s. 5,451,942,

5,956,674, 5,974,380, 5,978,762, 6,487,535 and other US. and world-wide patents issued and pending. “DTS” and “DTS 2.0 + Digital Out” are trademarks of Digital Theater Systems, Inc.

Copyright 1996, 2003 Digital Theater Systems, Inc. All Rights Reserved.

Manufactured under license from Dolby Laboratories.

“Dolby,” “Pro Logic,” and the double-D symbol are trademarks of Dolby Laboratories.

15

D4754S P1-25 (040202).p65

15 2004/02/02, 13:22

Initial Setup for Basic Connections (Ready to Play)

Before doing Initial Setup

1

2

3

Turn TV on.

See connections a

RF Coaxial Cable Connection and b AV Cable Connection on page 12.

<RF Coaxial Cable Connection>

Set TV to channel 3.

<AV Cable Connection>

Set TV to VIDEO.

[DECK

➛

• Go to “Initial Setup (Ready to Play).” (See below.)

[Cable Box

➛

• Turn on Cable Box and set it to your Public Broadcasting Station (PBS) channel in your time zone.

• If you use a DSS Receiver, it must be turned off.

Initial Setup (Ready to Play)

1

2

Press VCR on remote for VCR mode.

Plug DECK Power Cord into AC wall outlet. DECK comes on and auto channel and clock set starts.

• If screen below does not appear, check DECK - TV connection and, if TV is tuned to channel 3, try switching it to channel 4.

• To change VCR’s output channel, please see “VCR’s Output Channel” on page 19.

Plug VCR Power plug into an AC wall outlet.

CH AUTO SET PROCEEDING

CANCEL : STOP

AUTO CLOCK SET

PROCEEDING

Notes

• Function buttons are void during Initial Setup.

• To eject a tape during Auto Set, press EJECT on remote or STOP/EJECT twice on DECK.

Then make settings manually. (See p. 18.)

• If Auto Clock Set takes more than 30 minutes, press STOP and perform settings manually. (See p. 18.)

16

CANCEL : STOP

Continued on next page...


D4754S P1-25 (040202).p65

16 2004/02/02, 13:22

dy to Play)

*Important: If a remote control button does not work when pressed, press the VCR button on the remote and try the button again.

EJECT

3 Settings are made automatically.

When complete, this screen appears.

ACTION

SELECT

SET

VCR

If “AUTO CLOCK SET IS INCOMPLETE” appears, manually set clock (below).

AUTO CLOCK SET

IS I NCOMPLETE

PLEASE SET CLOCK BY

PRESSING ACT I ON KEY

STOP/EJECT

17

Manual Clock Set

If Auto Clock Set was incomplete.

1 Press ACTION* on remote to display

CLOCK screen.

SET CLOCK

1 / 1/2004 THU --

-

DST : ON

- - - - - - - - -- - - - - - - -- - - - - -

SELECT : SET : SET

END : ACT I ON

2

Press to select the month and SET to set. In the same manner, select and set the date, year, time, and DST (Daylight

Saving Time).

SET CLOCK

6 /20/2004 SUN -

-

DST : ON

- - - - - - - - -- - - - - - - -- - - - - -

SELECT : SET : SET

START : ACT I ON

3

Press ACTION to start clock and exit.

17

2004/02/02, 13:22 D4754S P1-25 (040202).p65

Reset Language, Channels, Clock, VCR’s O

1

MENU

SET UP VCR

SET UP CLOCK

SET UP CHANNEL

IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

SET : SET

EXIT : ACTION

Press ACTION*

to display MENU.

• PROGRAM functions are not available when using COMPONENT Video Output and S-VIDEO OUT. Please set TV to either RF INPUT or VIDEO INPUT, and then press PROGRAM.

2

Language

1) Press to select language item.

MENU

SET UP VCR

SET UP CLOCK

SET UP CHANNEL


VCR’S OUTPUT CH:3

Channels

1) Press to select

“SET UP CHANNEL,” and press SET.

MENU

SET UP VCR

SET UP CLOCK

SET UP CHANNEL


VCR’S OUTPUT CH:3

EXIT : ACTION

2) Press SET repeatedly to change language item as shown below.

MENU

PREPARAR VCR

FIJAR RELOJ

FIJAR CANAL

LANGUE/LANGUAGE:ESPAÑOL

SALIDA DE VCR CANAL : 3

EXIT : ACTION


“ANTENNA,” then

press SET to set your antenna system

(“TV” or “CABLE.”)

SET UP CHANNEL

ANTENNA : CABLE

AUTO SET

WEAK S I GNAL D I SPLAY : OFF

SALIR : ACTION

For Spanish SELECT : SET : SET

EXIT : ACT I ON


“AUTO SET,” then

press SET.

• If you use a Cable Box, set it to the PBS channel in your time zone.

For French

MENU

SET UP VCR

SET UP CLOCK

SET UP CHANNEL


VCR’S OUTPUT CH:3

SET : SET

EXIT : ACTION

For English

3) Press ACTION to exit.


CANCEL : STOP

• After Channel Auto Set is finished, Auto Clock

Set will be performed.

Clock


“SET CLOCK,” and

press SET.

MENU

SET UP VCR

SET UP CLOCK

SET UP CHANNEL


VCR’S OUTPUT CH:3

EXIT : ACTION


“MANUAL,” and press SET.

(For Auto Clock Set, select

“AUTO CLOCK SET.”)

SET CLOCK

AUTO CLOCK SET

NUAL

T I ME ZONE ADJUST : 0

SELECT : SET : SET

EXIT : ACT I ON

(“TIME ZONE ADJUST” appears only when auto clock is set.)

SET CLOCK

1 / 1/2004 THU --

-

DST : ON

- - - - - - - - -- - - - - - - -- - - - - -

SELECT : SET : SET

END : ACT I ON

3) Press and to select, then set the date, time, and DST (Daylight

Saving Time).

4) Press ACTION to start

Clock and exit this mode.

18


D4754S P1-25 (040202).p65

18 2004/02/02, 13:22

k, VCR’s Output Channel


POWER

NUMBER keys

CH /

ADD/DLT

ACTION

SELECT

SET

VCR

Time Zone Adjust

(Only when Auto Clock is set.)


“SET CLOCK,” and

press SET.

MENU

SET UP VCR

SET UP CLOCK

SET UP CHANNEL


VCR’S OUTPUT CH:3

SET : SET

EXIT : ACTION

VCR’s Output

Channel


“VCR’S OUTPUT CH.,” and press SET.

MENU

SET UP VCR

SET UP CLOCK

SET UP CHANNEL


VCR’S OUTPUT CH:3

EXIT : ACTION


“TIME ZONE ADJUST,”

2) Press SET.

SET CLOCK

AUTO CLOCK SET

MANUAL

T I ME ZONE ADJUST : 0

I F YOU PRESS ACT I ON

KEY, VCR’ S OUTPUT CH

SW I TCHES TO CH 4.

3) Press ACTION.

SELECT : SET : SET

EXIT : ACT I ON

PLEASE TUNE YOUR TV TO

CH 4.

and press SET to subtract or add hour(s) as necessary.

After 3 seconds

3) Press ACTION.

• “TIME ZONE ADJUST” returns to “0” if clock is set manually.

MENU

SET UP VCR

SET UP CLOCK

SET UP CHANNEL


VCR’S OUTPUT CH:4

SET : SET

EXIT : ACTION

• To Make Corrections, repeat steps 1) ~ 3).

Add or Delete a Channel

To add channel:

Select channel with NUMBER keys and press ADD/DLT.

CHANNEL 08 ADDED

To delete channel:

Select channel with CH / or

NUMBER keys and press ADD/DLT.

CHANNEL 08 DELE TED

DST (Daylight Saving Time)

DECK auto adjusts clock for DST.

(p. 17.)

Spring (First Sunday in April)

DST:ON

➛

Autumn (Last Sunday in October)

DST:ON

➛

• If your area does not observe

Daylight Saving Time, select

DST:OFF.

• Keep these time changes in mind when programming DECK for timer recordings.

19

D4754S P1-25 (040202).p65

19 2004/02/02, 13:22

Playback/ Record on a Tape

Ready Checklist

All connections are made. (pp. 12 ~ 15)

TV and DECK are plugged in.

TV is on and tuned to CH 3, 4, or VIDEO.

Remote is in VCR mode. (Press VCR.)

EJECT VCR/TV

CH /

Playback a Tape

1

Insert a tape.

• DECK power comes on. If Auto VCR/TV (see p. 32) is set to “OFF,” press VCR/TV on the remote for VCR mode.

VCR

2

Press PLAY* to play a tape.

• If tape has no rec. tab (p. 6), auto play begins.

Special Features During Play

FF/

SLOW+

REW/

SLOW-

Forward/Reverse Scene Search

➛

➛

After search has begun, each additional press of

FF or REW changes speed.

PAUSE/

STILL

REC

Notes

• Picture interruption may occur with some TVs.

• FF and REW search speed may vary depending on current tape position.

• After 10 minutes in search mode, VCR returns to

Play mode to protect the tape and the video heads.

Still (Freeze) Picture

➛

➛

Frame by Frame Picture

➛

➛

Slow Motion Picture

➛

REW/SLOW- (decrease speed) in Still

➛ mode.

➛ Press PLAY to release.

DVD

PLAY

STOP

Notes

• These features work best in SP or SLP mode.

• The sound will be muted.

• To reduce picture noise, see “Manual

Tracking Control” on page 4.

• After 3 minutes in Still or Slow mode, VCR stops to protect the tape and the video heads.

Playback using DECK buttons

1

Insert a tape.

SPEED

2

Press PLAY.

3

Press STOP to stop a tape.

Rapid Rewind/FF

Press REW/SLOW- or FF/SLOW+ in Stop mode to rewind or fast forward a tape.

• Rewinds a T-120 tape in approx. 1 minute.

Press EJECT on remote, or STOP/EJECT on DECK to eject a tape.

Multi Function Display

Press STOP/EJECT to stop and/ or eject a tape.

20


D4754S P1-25 (040202).p65

20 2004/02/02, 13:22


Record on a Tape

2

3

Insert a tape with a record tab (p. 6).

1

• DECK power comes on. If Auto VCR/TV (see p. 32) is set to “OFF,” press VCR/TV on the remote for

VCR mode.

This video recorder, equipped with HQ

(High Quality) system, is compatible with existing VHS equipment.

Only use tapes with the mark.

Only tapes tested and inspected for use in 2, 4, 6, and 8 hour machines are recommended.

Press CH

, or NUMBER keys to select the channel.

• If channel number is over 100, first press 100 key then the other 2 digits.

• For “LINE” input, see p. 35.

Press SPEED

to select the record speed (p. 4).

SP = Standard Play

SLP = Super Long Play

• Speed appears on-screen and on Multi Function Display.

Note

Remove loose or peeling

labels from tapes to prevent

tape jam.

4

Press REC

to start recording.

(The VCR REC indicator lights up on Multi Function

Display),

• To edit out unwanted scenes, press PAUSE/STILL to pause, and again to resume recording.

• You cannot view another channel during recording.

5

Press STOP

to stop recording.

CH 02

0 : 0 0 : 0 0

SP

REC T I ME : 0 : 30

T I ME : PRESS REC KEY

CANCEL : PRESS STOP KEY

<One Touch Recording screen>

One Touch Recording (recording in progress),

➛ press REC repeatedly to set the recording length

(30 min. ~ 4 hours) (see right).

• DECK shuts off after the preset record length.

Record one station, watch another,

Normal Rec 0:30 1:00

4:00 3:00 2:00 1:30

➛

(change to TV mode),

➛ select channels at TV (recording continues).

Select Channels at DECK (In Stop or

Rec. Pause mode)

➛ press VCR/TV on the remote

(change to TV mode),

Record using DECK buttons

4

Press REC to start recording.

1

Insert a tape.

Play a disc while recording a tape.

➛

➛

Notes

• It is not possible to record from DVD/ CD to

VHS tape using DECK.

• Watching one channel and recording another is not possible when using Cable Box or

DSS Receiver.

• After 5 minutes in Pause mode, DECK stops to protect a tape and video heads.

2

Select

Channel.


Press STOP/EJECT to stop.

21

D4754S P1-25 (040202).p65

21 2004/02/02, 13:22

Basic DVD Operation

Ready Checklist


DECK is plugged in.

If DECK is connected to an audio amplifier, turn the stereo system’s power on.

OPEN/

CLOSE

POWER

NUMBER keys

SELECT

SET

FF/

SLOW+

REW/

SLOW-

PAUSE/

STILL

TITLE

10

MENU

STOP

DVD

PLAY

SKIP+

SKIP -

VSS

RETURN

Operation using DECK buttons

1

Press

POWER.

3, 7

Press

OPEN/CLOSE.

4

Press PLAY.

3

Insert a disc.

6

Press STOP.

* 1 Interactive DVD...

May include multiple camera angles, stories, etc.

1

Press

POWER* on the remote or DECK.

Press

DVD to select DVD mode.

2

• If a disc is already inserted, go to step 4.

(Depending on the disc, playback may start automatically.)

3

Press OPEN/CLOSE,

and then place a disc into the disc tray.

1

2

• Hold disc by its edges only (p. 6) with printed side up and use guides to place into tray.

2

DVD-RAM

➡ see p. 42

4 Press

PLAY to start playing.

Disc tray closes automatically.

CLOSE

READING

• You may also close tray by

pressing

OPEN/CLOSE.

• Data reading time differs with each disc.

If an interactive DVD* 1 is used and TITLE MENU appears, go to step 5.

<Example1>

T I TLE MENU

Dogs Cas t l es

Love r s B i r ds

5

Press

or

NUMBER keys (see below) to select title, and press SET or

PLAY to start playing.

• Pressing SET or PLAY is not necessary when using

NUMBER keys.

<Example2>

Using NUMBER keys starts play automatically.

The number of available titles varies with each disc.

<Input

Example>

1 digit number 1 •••• 1

2 digit number 12 ••• 10

➛ 1 ➛ 2

Press

SKIP+

| or

SKIP- |

to go to next or previous menu screen.

• SKIP function not available with all discs.

Please refer to disc jacket for operation information.

To return to menu (play stops)

Press

TITLE, MENU, or RETURN.

6

Press

STOP to stop playing.

7

Press

OPEN/CLOSE to eject the disc.

22


D4754S P1-25 (040202).p65

22 2004/02/02, 13:22

*Important: If a remote control button does not work when pressed, press the DVD button on the remote and try the button again.

■ Forward/Reverse Scene Search

Press

FF/SLOW+ or REW/SLOW- during play.

Press

PLAY to release.

• Search speed, slow at first, increases with each additional press of the button up to 5 levels.

■ Forward/Reverse Chapter/Track Skip

Press

SKIP+ | or

SKIP- |

during play.

Each press skips a chapter (DVD-Video), track (DVD-Audio/CD) or Program/Play List/

Marker (DVD-RAM).

•

DVD-Video, DVD-Audio and CD

Pressing SKIP- |

once midway through a chapter/track returns to the start of that chapter/track. Each additional press skips back one chapter/track.

Current playback position

V.S.S.

(Virtual Surround Sound)

Enjoy a surround-like effect if you are using two front speakers only. The effect is broadened and sound seems to come from virtual speakers on either side if the disc has surround signals recorded on it.

Press

VSS in DVD mode.

• The Surround sound effect can be changed by pressing VSS repeatedly as shown by the figure below.

VSS OFF

VSS1

VSS OFF (default) VSS2

Chapter/Track Chapter/Track Chapter/Track

Reverse Skip Forward Skip

•

DVD-RAM

Pressing SKIP- |

once midway through a program/play list returns to the start of that program/play list. Each additional press skips back one program/play list.

Current playback position Marker

VSS3

Note

• Surround sound effect is available in DVD mode only.

• Turn off the surround effects on the other equipment.

• V.S.S. will not work, or will have less effect, with some discs.

• Turn V.S.S. off if it causes distortion.

• Sound will only come from the two front speakers if V.S.S. is on.

Program/Play List Program/Play List Program/Play List

Reverse Skip Forward Skip

■

Still Picture or Pause

Press

PAUSE/STILL during play.

Press


• DVD : DECK will enter still picture mode.

• CD : DECK will enter pause mode.

■ Frame by Frame Picture

(DVD)

Press

PAUSE/STILL in still mode.

Press


• Each press advances picture one frame.

• Hold button down for consecutive frame advance.

• Whether pictures are advanced by “FRAME” or

“FIELD” is selected automatically. (See p. 54.)

■

Slow Motion Picture

(DVD)

Press

FF/SLOW+ or REW/SLOW- in still mode.

Press


• Slow motion speed, slow at first, is increased with each additional press of the button up to

5 levels.

Auto-Power Off Function

Power turns off after DECK has been in

Stop mode (DVD) for about 5 minutes.

• When appears on the screen while a button is being operated, it means that the corresponding operation is prohibited by DECK or the disc.

Resume Function

DECK memorizes the point where STOP is pressed (STOP is displayed on screen).

Press

PLAY to resume play from this point.

Pressing

STOP again or opening the tray cancels RESUME, however, RESUME is not canceled when power is turned off and on.

• RESUME works only with discs for which elapsed play time is displayed during play.

• When a DVD-RAM still picture is played back, the counter will not be displayed, however RESUME will function.

Notes

• Please read the disc jacket for operation information.

• If a single sided disc is placed in upside down, “THIS TYPE OF DISC CANNOT

BE PLAYED. PLEASE INSERT A

DIFFERENT DISC” is displayed.

• Remove disc and press DECK POWER off when not in use.

• Disc continues to rotate with menu displayed even after play is done.

Press STOP to clear menu display when finished with menu.

23

D4754S P1-25 (040202).p65

23 2004/02/02, 13:22

Timer Recording

Ready Checklist


TV and DECK are plugged in.

Clock set correctly. (p. 18)

Tape has record tab intact. (p. 6)

Remote is in VCR mode. (Press VCR.)

Sufficient tape remaining for recording time.

1

Press PROG*

to display Program.

2

P DT START STOP CH SPD

1 -- --:-- --:-- -- --

2 -- --:-- --:-- -- --

3 -- --:-- --:-- -- --

4 -- --:-- --:-- -- --

SELECT : SET : SET

EXIT : PROG

Example

Today

14

13

31

1

SELECT /

Selection Order

12

DAILY

WEEKLY

(SU)

WEEKLY

(MO)

WEEKLY

(SA)

1) Press .

2) Set record DATE, press

to select:

1~31= one time, or

DAILY=Monday~Friday, or WEEKLY= same time each week.

• See selection order left.

3) Set remaining items, press SET

to set START/ STOP times,

CH (channel) or LINE input (p. 35), and tape speed (SP, SLP).

Then press to select.

Press PROG

to end programming.

POWER

ADD/DLT

SELECT

SET

VCR

PROG

3


1 13 2:00p 3:20p 02 SLP

2 -- --:-- --:-- -- --

3 -- --:-- --:-- -- --

4 -- --:-- --:-- -- --

SET COMPLETED

CANCEL : ADD/DLT

SELECT : SET : SET

EXIT : PROG

To Enter More Programs, press

to select and

press SET

to set an unused program number, and then repeat step 2.

Or

Press PROG

to exit.

VCR mode Indicator

VCR REC Indicator

V C R

TIMER REC

Hi - Fi

TIMER Indicator

<Multi Function Display>

• The “Timer” Indicator lights up on DECK.

• You can set Timer Recording with the power on or off.

• “TIMER REC WILL START SOON” appears on-screen for 2 minutes before Timer Recording starts. If DECK is in DVD mode, no message appears, but the VCR REC Indicator, the VCR mode indicator and

“REC” will flash on Multi function Display.

24


D4754S P1-25 (040202).p65

24 2004/02/02, 13:22


Review, Replace or Clear Program Contents:

(Recording is not in progress)

1

2

Press PROG

to display Program List.


1 13 2:00p 3:20p 02 SLP

2 14 7:00p 7:30p 10 SP

3 -- --:-- --:-- -- --

4 -- --:-- --:-- -- --

CANCEL : ADD/DLT

SELECT : SET : SET

EXIT : PROG

Press

to select number.

To cancel a Timer

Recording in progress...

Hold down STOP in VCR mode for a few seconds to cancel the Timer

Recording.

(The “TIMER” Indicator goes out on Multi Function Display.)

• Any future daily or weekly recording will be performed as programmed.

3

To Replace program...


1 13 2:00p 3:20p 02 SLP

2 14 7:00p 7:30p 10 SP

3 -- --:-- --:-- -- --

4 -- --:-- --:-- -- --

Repeat Step 2 (p. 24) to set new programs.

SELECT : SET : SET

EXIT : PROG

or

To Clear program...

Press ADD/DLT.


1 -- --:-- --:-- -- --

2 14 7:00p 7:30p 10 SP

3 -- --:-- --:-- -- --

4 -- --:-- --:-- -- --

SELECT : SET : SET

EXIT : PROG

4

Press PROG

to end the programming.

Notes

• If you are using a Cable Box, the VCR’s channel for Timer Recording must be set to the Cable Box input channel and Cable Box must be manually set to the desired channel. Cable Box power must be left on.

• 2 minutes before Timer Recording is performed, “PLEASE PREPARE FOR TIMER

REC” appears and Timer Indicator flashes.

Be sure a cassette with record tab is loaded and DECK is in Stop mode.

• If a power interruption occurs while programming the timer, the timer program(s) may be canceled. If “TIMER PROGRAMS WERE LOST DUE TO POWER INTERRUPTION” appears on-screen, please re-enter the timer programs.

• If the start time for Timer Recording comes up during recording and playing back,

Timer Recording will not be performed.

Important notes when using DSS Receiver

• When recording programs via DSS Receiver, DSS Receiver must be left on.

• When recording programs via an antenna or cable, DSS Receiver must be turned off.

25

D4754S P1-25 (040202).p65

25 2004/02/02, 13:22

MTS Broadcast/ VHS Hi-Fi Stereo System

Connection

Make the Audio/Video Connection as shown on pp. 12 ~ 15.

• You can use TV connected to a Stereo amplifier and speakers instead of Stereo TV.

Receivable Broadcast Types

The following are possible audio broadcast types and onscreen displays.

The signal being received is indicated with a “ ” mark while the selected audio mode is indicated with an arrow.

To display the broadcast signal being received,

MTS Stereo and SAP broadcast

Multi-channel Television Sound

Stereo (main language) and

Secondary Audio Program (sub language) broadcasts are being received simultaneously.

Select STEREO or SAP audio mode.

STOP 1 2 : 0 0AM

STEREO

SAP

MONO

CH 02

0 : 0 0 : 0 0

SP

MTS Stereo broadcast

Multi-channel Television Sound

Stereo broadcast. Select STEREO audio mode.

• If stereo broadcast is weak and display flickers, select MONO audio mode for possible better results.

STOP 1 2 : 0 0AM

STEREO

SAP

MONO

CH 02

0 : 0 0 : 0 0

SP

AUDIO

(SAP/Hi-Fi)

DISPLAY

SAP broadcast

Secondary Audio Program (sub language) broadcast. Select SAP audio mode for the sub language.

STOP 1 2 : 0 0AM

STEREO

SAP

MONO

CH 02

0 : 0 0 : 0 0

SP

MONO broadcast

Normal monaural sound broadcast.

STOP 1 2 : 0 0AM

STEREO

SAP

MONO

CH 02

0 : 0 0 : 0 0

SP

Equipped with

®

-TV

Noise Reduction for true MTS reproduction.

®

-TV Noise

Reduction is required for good stereo separation and audio fidelity.

®

is a registered trademark, and is licensed by

®

Technology Licensing.

26


D4754S P26-35 (040202).p65

26 2004/02/02, 13:22


Audio Mode for Recording

1

Press AUDIO (SAP/Hi-Fi)

to display audio mode.

(Display disappears after 5 seconds.)

2

STEREO

SAP

MONO

Press AUDIO (SAP/Hi-Fi) repeatedly to select desired mode.

• Refer to “Receivable Broadcast Types” on p. 26.

• Arrow indicates selection.

3

Make a recording.

See p. 21.

Audio Mode for Playback

1

Start playback.

See p. 20.

2 Press AUDIO (SAP/Hi-Fi)

to display audio mode.

3

H I F I : L / R

H I F I : L

H I F I : R

NORMAL

Press AUDIO (SAP/Hi-Fi) repeatedly to select desired mode.

• Select “HIFI (L/R)” or “HIFI (L)” or “HIFI (R)” to listen to stereo recordings in stereo sound.

Select “NORMAL” for monaural sound.

• Display disappears after 5 seconds.

• Arrow indicates selection.

Notes

• Only tapes recorded in Hi-Fi stereo will playback with true stereo sound.

Standard stereo tapes will playback in monaural sound.

• To listen to Hi-Fi stereo playback, the DECK AUDIO (L/R) jacks must be connected to a stereo TV or an external stereo amplifier and speakers. (See pp. 12, 14.)

• If tracking is adjusted during playback, Hi-Fi audio may revert to normal audio.

• Hi-Fi and normal audio playback volume level may differ.

27

D4754S P26-35 (040202).p65

27 2004/02/02, 13:22

Multi-Brand Control Feature

Multi-Brand Control Setup

The Remote Control can be set to control some TVs.

1

Find your TV Brand Code Number on the following page.

2

Set up for TV control,

➛

➛

3

Confirm code entry,

➛ press POWER to turn selected unit on or off.

• See table below for controllable functions in each mode.

Notes

• Repeat setup after remote battery replacement.

• Remote will not control every TV made by the manufacturer listed. If you get no response, your particular unit cannot be controlled.

There are NO additional codes for the products listed. If your product is not listed, then the remote is not compatible with that product.

Using Multi-Brand Control

After remote is set up, you can select VCR, DVD, or TV for the desired function.

Press VCR,

DVD, or TV on the remote.

(Table below shows available remote buttons for each mode.)

Mode

Unit

DVD/VCR TV

DVD

VCR

All

VOL

+

/

-

TV

EJECT/ OPEN/CLOSE

*

,

DISPLAY, PLAY, STOP,

FF/SLOW+, REW/SLOW-,

VCR/TV, PAUSE /STILL, SKIP,

AUDIO, CM/ZERO, SPEED, REC,

TAPE POSITION, PAGE,

COUNTER RESET

POWER, INPUT, NUMBER keys,

ENTER, CH / , VOL

+

/

-

*

Bold: VCR Function


Bold Italic: VCR and DVD Functions

Normal: TV

Notes

• Not all functions listed may be controllable.

• In TV mode, it may be necessary to press ENTER after pressing NUMBER keys for channel selection.

28


D4754S P26-35 (040202).p65

28 2004/02/02, 13:22

TV Brand Code Numbers

Panasonic ......................................... 01, 02

Quasar .............................................. 01, 02

RCA ......................................................... 03

GE ........................................................... 03

Zenith ...................................................... 04

Magnavox ............................................... 05

Sylvania .................................................. 05

Sharp ................................................. 06, 07

Sony ........................................................ 08

Toshiba ................................................... 09

Sanyo ...................................................... 10

Fisher ...................................................... 10

JVC ......................................................... 11

Hitachi ..................................................... 12

Mitsubishi .......................................... 07, 13

Samsung ................................................ 14

Gold Star .................................... 15, 16, 17

Important Notes

• Some manufacturers use several codes for one brand.

If the first code entered fails, try the next one listed.

• Some TVs require you to turn on the power manually.

POWER

VCR

TV

NUMBER keys

DVD

ENTER

D4754S P26-35 (040202).p65

29 2004/02/02, 13:22

29

Tape Operation

Search System

For each recording, an invisible index mark is placed on the tape. A program index and information are also included for timer recordings. These marks are used to access or scan recordings.

Index Search

1

2

INDEX SEARCH

ENTER INDEX NUMBER :1

USING 1- 9 KEYS

FORWARD SEARCH :FF

REVERSE SEARCH :REW

EXIT :SEARCH

INDEX SEARCH

FORWARD SEARCH : FF

REVERSE SEARCH : REW

Press SEARCH*

to display SEARCH in Stop or Play mode, and then

press NUMBER

keys to select recording number.

• To calculate number, see below.

Press FF/SLOW+

or REW/SLOW- on the remote to start search.

Play begins at search end.

To search forward or back 1 index,

press FF/SLOW+ or

REW/SLOW- on the remote while screen left is displayed (10 sec.).

• To cancel, press

PLAY or STOP.

Zero Search

To quickly return to a specified tape location.

1

Press DISPLAY during play to display Counter.

2

3

4

5

PLAY 1 2 : 0 0AM

0 : 0 0 : 0 0

SP

Continue to record, playback etc.

Press STOP.

REW 1 2 : 3 0AM CH 02

0 : 30 : 30

SP

Press COUNTER

RESET on remote at desired position to reset to “0:00:00”.

Press CM/ZERO

in Stop mode to start

Zero Search.

STOP 1 2 : 3 1AM CH 02

0 : 0 0 : 0 0

SP

• DECK will go into FF or REW mode and stop at the last point the Counter was set to 0:00:00.

Commercial Skip

To Calculate Index Number

Example 1:

To go to rec. 2 from rec. 4, enter 3 and press REW.

DECK fast forwards (skips) over 1, 2, or 3 minutes of recorded tape as desired.

1

Press CM/ZERO in Play mode.

• The skip time can be changed by pressing CM/ZERO repeatedly as shown by the figure below.

1 2 3 4 5 6 7

PLAY

Example 2:

To go to rec. 6 from rec. 2, enter 4 and press FF.

1st Press 1 min Skip

2nd Press 2 min Skip

1 2 3 4 5 6 7

NOTE: indicates start points of each recording.

3rd Press 3 min Skip

Note

30

• No indication appears on-screen.

• If Index Search is started very close to an index mark, that index mark may not be counted in the search.


D4754S P26-35 (040202).p65

30 2004/02/02, 13:22


Tape Select

Select your tape length so the tape position and amount of tape remaining are properly displayed.

(See “Tape Position Display” section right.)

1

Press ACTION

to display MENU.

2

MENU

SET UP VCR

SET UP CLOCK

SET UP CHANNEL


VCR’S OUTPUT CH:3

Press

to select

“SET UP VCR,” and

press SET.

Tape Position Display

To find out the present tape position and amount of tape remaining.

Tape position is displayed incorrectly in the following cases:

• If VHS-C type cassettes, tapes under 30 minutes, tapes over 180 minutes, or incompatible tapes are used.

• If the correct tape length is not selected.

(See “Tape Select” section left.)

3

EXIT : ACTION

SET UP VCR

REPEAT PLAY

REMOTE WARN I NG

AUTO SHUT-OFF

FRONT DISPLAY

AUTO VCR/TV

TAPE SELECT

: OFF

: ON

: OFF

: ON

: ON

: T-120

SELECT : SET : SET

END : ACT I ON

Press

to select

“TAPE SELECT,” and press SET to set “T-120,” “T-160” or “T-180.”

T-120 T-160 T-180

• Select “T-120” for tapes 120 minutes or less, “T-160” if 140 or 160 minutes, and

“T-180” if 180 minutes.

4

Press ACTION

to return to normal screen.

1 Press TAPE POSITION

to detect current tape position.

DETECTING TAPE POSITION

SP

R 120 M I N.

BEG I N END

• “DETECTING TAPE

POSITION” only appears the first time a cassette is inserted and it takes several seconds for correct indication to appear.

• The present tape position indication and amount of tape remaining (according to tape speed) are displayed.

Tape remaining time display may not be precise.

Repeat Play

Set to playback a recording over and over.

1

Press ACTION

to display MENU.

2

MENU

SET UP VCR

SET UP CLOCK

SET UP CHANNEL


VCR’S OUTPUT CH:3

SET : SET

EXIT : ACTION

Press

to select “SET UP

VCR,” and press

SET.

2

Press TAPE POSITION

(or wait 5 seconds) to return to normal screen.

3

4

SET UP VCR

REPEAT PLAY

REMOTE WARN I NG

AUTO SHUT-OFF

FRONT DISPLAY

AUTO VCR/TV

TAPE SELECT

: OFF

: ON

: OFF

: ON

: ON

: T-120

SELECT : SET : SET

END : ACT I ON

Press

to select “REPEAT

PLAY,” and press

SET to set “ON” or

“OFF.”

• Play repeats at tape end or if unrecorded portion over 30 sec. is detected.

Press ACTION


Note

• For repeat play in DVD mode, see page 47.

Auto Operation Functions

Auto Play

Insert a tape

➛ Power comes on,

➛ Play starts if there is no record tab

(see p. 6).

Auto Rewind

Play

Fast Forward

➛ Tape end ➛ Rewind

➛

Stop

Play Auto Eject

(Repeat Play must be off)

Play

➛

Tape end

➛

Rewind

➛

Stop

➛

Tape ejects if some programs are set.

31

D4754S P26-35 (040202).p65

31 2004/02/02, 13:22

Special VCR Features

The VCR/TV selection can be set to auto or manual.

1

Press ACTION*

to display MENU.

2

MENU

SET UP VCR

SET UP CLOCK

SET UP CHANNEL


VCR’S OUTPUT CH:3

Press

to select “SET UP VCR,” and

press SET.

SET : SET

EXIT : ACTION

3

SET UP VCR

REPEAT PLAY

REMOTE WARN I NG

AUTO SHUT-OFF

FRONT DISPLAY

AUTO VCR/TV

TAPE SELECT

: OFF

: ON

: OFF

: ON

: ON

: T-120

SELECT : SET : SET

END : ACT I ON

Press

to select “

AUTO VCR/TV

,” and

press SET

to set “ON” or “OFF.”

• OFF(Manual): You select “VCR” or “TV” mode using the VCR/TV button on the remote.

• ON(Auto): “VCR” mode is automatically set when

VCR is turned on, or in Play mode.

4

Press ACTION


Note

• For more on VCR/TV selection, see “Record one station, watch another” and “Select channels at DECK” sections (see p. 21).

VCR Lock Feature

When set to ON, all operations except for timer record and tape eject are prohibited. Useful for households with small children.

To turn on, hold down REC on DECK in Stop mode with no tape inserted for 7 seconds.

(Please ignore “NO CASSETTE” warning.)

Blue LIGHT ON/OFF Feature

You can turn DECK’s blue light off if you find it to be glaring.

To turn LIGHT off,

press DISPLAY for 5 seconds in VCR mode.

To turn LIGHT on, repeat above.

Notes

• This operation is not possible in power off mode.

• If you unplug DECK, DECK turns to defult setting (Blue light turns on).

REC

Blue Light

VCR LOCK ACT I VATED

To turn off, repeat above.

VCR LOCK OFF

• VCR Lock cancels in 24 hours.

Note

• DVD functions will work even when VCR Lock is set to ON.

32


D4754S P26-35 (040202).p65

32 2004/02/02, 13:22


D4754S P26-35 (040202).p65

ACTION

SELECT

SET

DISPLAY

Weak Signal Display Feature

When “ON,” picture is displayed regardless of signal strength.

1

Press ACTION

to display MENU.

2

MENU

SET UP VCR

SET UP CLOCK

SET UP CHANNEL


VCR’S OUTPUT CH:3

Press

to select “SET UP

CHANNEL,” and

press SET.

SET : SET

EXIT : ACTION

3

SET UP CHANNEL

ANTENNA : CABLE

AUTO SET

WEAK S I GNAL D I SPLAY:OFF

SELECT : SET: SET

EXIT : ACT I ON

Press

to select “WEAK SIGNAL

DISPLAY,” and

press SET

to set “ON” or “OFF.”

• ON: Picture is displayed regardless of signal condition, and may not always be clearly visible.

OFF: Screen turns solid blue when signal is weak or non-existent.

• Selecting ON has no effect on connected equipment with blue back feature.

4 Press ACTION


Auto Shut-Off Feature

The power shuts off at a preset time.

1

Press ACTION

to display MENU.

2

MENU

SET UP VCR

SET UP CLOCK

SET UP CHANNEL


VCR’S OUTPUT CH:3

Press


press SET.

EXIT : ACTION

3

SET UP VCR

REPEAT PLAY

REMOTE WARN I NG

AUTO SHUT-OFF

FRONT DISPLAY

AUTO VCR/TV

TAPE SELECT

: OFF

: ON

: OFF

: ON

: ON

: T-120

SELECT : SET : SET

END : ACT I ON

Press

to select “AUTO SHUT-OFF.”

Press SET repeatedly to change shut-off time as shown below.

2 Hours

OFF

4 Hours

6 Hours

4

Press ACTION


Note

• The shut-off countdown will not function during Play or

Record.

33

33 2004/02/02, 13:22

Special VCR Features (continued)

Remote Warning Feature

If Multi-brand feature is used (p. 28), and this feature is set to on, a warning appears whenever an invalid key is pressed in TV mode.


1

2

Press ACTION*

to display MENU.

MENU

SET UP VCR

SET UP CLOCK

SET UP CHANNEL


VCR’S OUTPUT CH:3

Press


press SET.

EXIT : ACTION

3

SET UP VCR

REPEAT PLAY

REMOTE WARN I NG

AUTO SHUT-OFF

FRONT DISPLAY

AUTO VCR/TV

TAPE SELECT

: OFF

: ON

: OFF

: ON

: ON

: T-120

SELECT : SET : SET

END : ACT I ON

Press

to select

“REMOTE WARNING,” and

press SET to set “ON” or “OFF.”

• If “OFF,” remote warning will not appear when invalid key is pressed.

4

Press ACTION


ACTION

SELECT

SET

STOP

STILL/

PAUSE

Multi Function Display

(Front Display) ON/OFF Feature

Multi Function Display (Front Display) can be set to

ON/OFF.

1 Press ACTION

to display MENU.

2

MENU

SET UP VCR

SET UP CLOCK

SET UP CHANNEL


VCR’S OUTPUT CH:3

Press


press SET.

EXIT : ACTION

INPUT

REC

3

SET UP VCR

REPEAT PLAY

REMOTE WARN I NG

AUTO SHUT-OFF

FRONT DISPLAY

AUTO VCR/TV

TAPE SELECT

: OFF

: ON

: OFF

: ON

: ON

: T-120

SELECT : SET : SET

END : ACT I ON

Press

to select

“FRONT DISPLAY,” and

press SET to set “ON” or “OFF.”

• ON : When set to “ON,”

Multi Function Display is displayed.

OFF : When set to “OFF,”

Multi Function Display is not displayed.

If a Timer Program is set,

Multi Function Display is displayed.

4

Press ACTION



34


(Front Display)

D4754S P26-35 (040202).p65

34 2004/02/02, 13:22

Copying Your Tapes (Dubbing)

Connection

VCR/ Camcorder

(Hi-Fi)

VIDEO

L

AUDIO

R

OUT

DVD/VCR DECK

IN 1

IN FROM ANT.

VIDEO

AUDIO1

L

R

OUT

VHF/UHF

OUT TO TV

TV

VHF/

UHF

Front of DECK

VIDEO IN 2 L-AUDIO IN2-R

(Audio/Video In Terminals on the front of DECK are available)

1

2

Connect VIDEO OUT terminal on Playing VCR to VIDEO IN terminal on DECK.

To monitor the dubbing, also connect TV as shown.

Connect “L” and “R” AUDIO OUT terminals on Playing VCR to “L” and “R”

AUDIO IN terminals on DECK.

In place of Playing VCR, you can use other equipment, such as a Camcorder.

Simply connect the unit’s Audio/Video outputs to DECK.

Playing (Source) VCR

1

Insert a pre-recorded tape.

2

Recording (Editing) DECK

Insert a blank tape with record tab.

Press INPUT to set DECK Input mode to

LINE for Video Input.

(See “Selecting the Input Mode” below.)

3

Press PLAY, then PAUSE immediately to enter PLAY/PAUSE mode.

Press REC, then STILL/PAUSE immediately to enter REC/PAUSE mode.

The operation of steps 4 and 5 must be done on the playing and recording VCRs at the same time.

Press PLAY to start dubbing.

Playing VCR starts playback.

Press STILL/PAUSE to start dubbing.

DECK starts recording.

4

5

Note

Press STOP to stop dubbing.

To Monitor Dubbing on TV

1 Turn TV on and tune to the Recording

VCR channel (CH 3 or CH 4).

2 If Auto VCR/TV (see p. 32) is set to

“OFF,” press VCR/TV on the remote for VCR mode.

• Dubbing tapes protected with Copy

Guard will result in poor quality recordings.

Press STOP to stop dubbing.

Selecting the Input Mode

Method 1: Press INPUT repeatedly.

Channel Number

↔

Method 2: Press CH / .

Display will change as below.

1 2 3

Press

LINE2 LINE1

(CABLE)

125 or

(TV)

69

Press

• “L1” or “L2” lights up on Multi Function Display

(about 4 seconds) when LINE1 or LINE2 is selected.

• LINE1: For rear audio/video connection.

LINE2: For front audio/video connection.

Caution:

• Unauthorized exchanging and/or copying of copyrighted recordings may be copyright infringement.

• Please note that some tapes cannot be dubbed on DECK.

Also, it is not possible to dub DVD/ CD to VHS tapes using DECK.

• When appears on the screen while a button is being operated, it means that the corresponding operation is prohibited by DECK or the disc.

35

D4754S P26-35 (040202).p65

35 2004/02/02, 13:22

Disc Operation

1

2

Subtitle Language (DVD only)

You can select a different subtitle language (if offered) than the one set at the Settings for DVD Operation. (See p. 52.)

Notes

Te amo

Press SUB TITLE*

in Play mode to display the subtitle selection on-screen.

• Display disappears after

5 seconds.

• When no subtitles are offered,

“-” will be displayed instead of the language number.

Press SUB TITLE,

NUMBER keys to select a desired language.

, or

Subtitle language being played back (see chart, right).

• If after several presses of the button the language does not change, language selection is not offered on the disc.

• When disc is removed, subtitles revert to initial setting language. If the initial language is not recorded on the disc, the disc’s priority language will appear.

• With DVD-RAM, the subtitle can only be set to ON/OFF.

The subtitle language cannot be selected.

• Subtitles may not change to the selected language immediately.

Ready Checklist

Please read “Basic DVD Operation” on page 22.

[Subtitle language]

[Audio sound track language]

ENG

FRA

DEU

ITA

ESP

NLD

SVE

NOR

DAN

POR

RUS

JPN

CHI

KOR

MAL

VIE

English

French

German

Italian

Spanish

Dutch

Swedish

Norwegian

Danish

Portuguese

Russian

Japanese

Chinese

Korean

Malay

Vietnamese

Thai

Other

• Change the No. by pressing , and press SET.

[Audio attribute 1 type, sampling

frequency, bit No. of the disc

(see p. 53.)

]

LPCM

Dolby Digital

DTS

44.1 kHz

192 kHz

16 bit

20 bit

24 bit

1 ch - 5.1 ch

1 ch - 5.1 ch

Linear PCM disc

Dolby Digital disc

DTS disc

Audio Soundtrack Language (DVD only)

You can change the audio soundtrack language, selected at the Settings for DVD Operation, to a different language if available. (See p. 52.)

(This operation works only with discs on which multiple audio soundtrack languages are recorded.)

1

2

Press

AUDIO

in Play mode to display the audio selection on-screen.


5 seconds.

Information of the audio stream currently being played back is displayed. (See page 53.)

Press AUDIO,

, or

NUMBER keys to select desired language.

Audio soundtrack language being played back (see chart, above right).

Notes

• If, after several presses of the AUDIO button the language does not change, language selection is not offered on the disc.

• When disc is removed, language reverts to initial setting. If this language is not recorded on the disc, the language recorded will be heard.

• With DVD-RAM, Audio Soundtrack

Language cannot be set. Audio stream and Audio mode (LR/L/R) setting can be made. Audio stream operation method is the same as Audio Soundtrack

Language. Press to move the cursor to Audio mode, then press AUDIO or

to select LR/ L/ R.

AUD I O : 1 LR

D o l b y D i g i t a l 3 / 2 . 1 c h

36


D4754S P36-72 (040202).p65

36 2004/02/02, 13:22

*Important: if a remote control button does not work when pressed, press the DVD button on the remote and try the button again.

When appears on the screen while a button is being operated, it means that the corresponding operation is prohibited by DECK or the disc.

ANGLE Indicator

Multiple Angle Viewing (DVD only)

DVDs may contain scenes shot from multiple camera angles allowing the same scene to be viewed at different angles. You can view these angles, if available, using the

ANGLE button.

1 Press ANGLE

in Play mode to display the angle selection on-screen.


5 seconds.

SELECT : ANGLE

Notes

• The ANGLE Indicator lights up on

DECK when a scene recorded at different angles is detected.

• The angle number can be set beforehand so that the angle is switched whenever the ANGLE

Indicator lights up.

2

Press

ANGLE repeatedly or to select the desired angle.

SELECT : ANGLE

Number of angle being played back.

Note

This function not available with DVD-RAM.

NUMBER keys

SELECT

SET

Vocal Selection for Karaoke Discs (DVD only)

1

Press

AUDIO in Play mode to display the audio screen.

2

Press to select

VOCAL and

press

AUDIO or to select as shown below.

• DVD Karaoke (1 vocal) VOCAL ON VOCAL OFF

• DVD Karaoke (2 vocals) VOCAL V1 VOCAL V2 VOCAL V1+V2 VOCAL OFF

ZOOM

ANGLE

AUDIO

SUB TITLE

Picture Zoom (DVD only)

You can enlarge specific portions of a picture and select the zoom ratio using the ZOOM button during

DVD playback.

Notes

• The subtitle cannot be enlarged or moved.

• During picture zoom, “ZOOM1” or

“ZOOM2” appears on-screen for 5 seconds.

• Zooming, on some discs, may result in poor picture quality, or may not operate at all.

Press

ZOOM repeatedly to change display as follows.

• You can enlarge the center portion of the image to one of 2 magnifications.

■ Use the , , and buttons to move the position up, down, left and right.

37

D4754S P36-72 (040202).p65

37 2004/02/02, 13:22

Disc Operation (continued)

Title Menu (DVD only)

Some DVDs have more than one title, e.g. movies.

If the disc offers a title menu, you can select the desired title number. (Operation may vary according to the disc.)

1

T I TLE MENU

Dogs Cas t l es

Love r s B i r ds

Press TITLE*

in Play mode to display the title screen.

2

<Example>

T I TLE MENU

Dogs Cas t l es

Love r s B i r ds

B i rds of the world

<Example>

Press

or

NUMBER keys

to select a title, and

press

SET or PLAY to start playing.

• “Pressing SET or PLAY” is not necessary when using

NUMBER keys.

NUMBER keys

CLEAR

ACTION

MENU

SELECT

SET

PLAY

STOP

DVD Menu (DVD only)

DVDs may offer a special menu. This menu may include guides to unique contents, audio/subtitle languages, etc.

Although contents and operation may vary, the following steps show basic procedure for using the menu.

1

DVD MENU

1 . SUBT I TLE

2 . AUD I O

3 . ANGLE

Press

MENU

in Play mode to display

DVD MENU.

<Example>

TITLE

2

38

DVD MENU

1 . SUBT I TLE

2 . AUD I O

3 . ANGLE

<Example>

Press

or

NUMBER keys

to select an item, and

press

SET or PLAY to perform.

• Pressing SET or PLAY is not necessary when using

NUMBER keys.

Repeat step 2 if there is

more than one menu.


D4754S P36-72 (040202).p65

38 2004/02/02, 13:22


2

Program Play (CD only)

You can program specific tracks and order of play.

1

Press ACTION

to display DVD MAIN MENU.

DVD MAIN MENU

D I SC LANGUAGES

AUDIO OUTPUT

ST I L L MODE

TV MODE

: AUTO

: 4 : 3 P a n & S c a n

PROGRESSIVE OUT: OFF

PLAY MODE

SELECT

SET

END

:

: SET

: ACT I ON

Press

to select

“PLAY MODE,” and

press SET

to display.

Ready Checklist

DECK is in DVD mode, press DVD.

CD is inserted.

Program Repeat Play

(CD only)

1

2

Do operation steps 1 through 5 at left on this page.

Press

DISPLAY to display Disc

Information screen.

(Disc Information Screen)

3

PLAY MODE

PROGRAM PLAY

RANDOM PLAY

Press

to select

“PROGRAM PLAY,” and

press

SET to display.

SELECT

SET

END

:

: SET

: ACT I ON

4

1

2

PROGRAM PLAY

D I SC

6 11 16

7 12 17

3 8 13 18

4 9 14 19

5 10 15 20

CLEAR LAST

CLEAR ALL

SELECT

SET

END

:

: SET

: ACT I ON

PROGRAM

5 8

15 6

1 13

3 2

2

START

Press

to select a track number (Track numbers on disc are displayed.), and

press

SET.

• Repeat step 4 to select another track.

• The selected track is added on the right side.

5

1

2

3

PROGRAM PLAY

D I SC

6 11 16

7 12 17

8 13 18

4 9 14 19

5 10 15 20

CLEAR LAST

CLEAR ALL

SELECT

SET

END

:

: SET

: ACT I ON

PROGRAM

5 8

15 6

1 13

3 2

2

START

Press

to select “START,” and

press

SET to start play of programs in the sequence selected.


STOP

during play, then press

CLEAR.

3

4

Press

DISPLAY to display

DECK Information screen.

Press

SET to enter Select mode.

Cursor move to “OFF.”

(DECK Information Screen)

5

Press

to select “DISC.”

(DECK Information Screen)

Notes

• Up to 15 tracks can be programmed.

• “ ” or “ ” (depending on disc) indicates additional

PROGRAM PLAY screen.

Press for next or previous screen.

• To clear the last program one by one

Press to move to “CLEAR LAST” and press

SET. (Pressing CLEAR on remote control also clears last program.)

• To clear all programs

Press to move to “CLEAR ALL” and press

SET. (Programs are also cleared when the power is turned off or the disc is removed.)

6

Press

SET to set mode.

Cursor moves to “REPEAT.”

To cancel, select “REPEAT :

OFF” in step 5, then press SET.

39

D4754S P36-72 (040202).p65

39 2004/02/02, 13:22

Disc Operation (continued)

Random Play (CD only)

Tracks are played in a random order.

1

Press ACTION*


2

DVD MAIN MENU

D I SC LANGUAGES

AUDIO OUTPUT

ST I L L MODE

TV MODE

: AUTO

: 4 : 3 P a n & S c a n

PROGRESSIVE OUT: OFF

PLAY MODE

SELECT

SET

END

:

: SET

: ACT I ON

Press

to select “PLAY MODE,” and

press SET

to display.

3

PLAY MODE

PROGRAM PLAY

RANDOM PLAY

SELECT

SET

END

:

: SET

: ACT I ON

Press

to select

“RANDOM PLAY,” and

press

SET

to begin random play.


STOP

during play, then press

CLEAR.

Ready Checklist


NUMBER keys

CLEAR

ACTION

SELECT

SET

STOP

VOLUME

ADJUST

DISPLAY

PAGE

Setting the VOLUME ADJUST (DVD only)

Some DVDs are recorded in lower than average volume levels.

For these DVDs, this DECK can be set so that the average volume is increased automatically.

Press

VOL.ADJ repeatedly to change “OFF”

↔

• “OFF” or “ON” lights up on Multi Function Display (about 3 seconds) when

VOL.ADJ is pressed.

Some DVD

[Low volume level]

VOLUME ADJUST “OFF”

Volume is at the original level.

VOLUME ADJUST “ON”

Volume level is increased when played back.

• “ON” is set ..... When a DVD is played back, the average volume is increased.

• “OFF” is set .... The volume level recorded on the disc is played back just as it is.

Notes

• While settings can be made with all discs, they may have no effect with some discs.

Please set as you prefer.

• When audio equipment is connected, setting the Sound Output level to “OFF” is recommended.

• If the sound becomes abnormal while playing a disc, set the Sound Output level to “OFF.”

40


D4754S P36-72 (040202).p65

40 2004/02/02, 13:22


DVD-Audio Operation (DVD-Audio only)

This DECK, equipped with a 192 kHz/ 24 bit Audio D/A converter, supports DVD-Audio recorded with high quality sound.

The DVD-Audio feature includes “Still Image Skip” and “Bonus Group Playback” functions. (See below.)

Please refer to “Basic DVD Operation” on pages 22 and 23.

Still Image Skip (DVD-Audio only)

DVD-Audio still images (only if contained) can be skipped over.

PAGE : 1

PAGE : 2

SELECT :

Press PAGE

in Play or Pause mode to display the still image and page number.

Each press of PAGE changes page number as shown below.

• Pressing PAGE on the last page returns to PAGE 1.

Press PAGE

PAGE : 1

Press PAGE

PAGE : 2

Press PAGE

PAGE : 3 .......

Press PAGE

PAGE : XX

SELECT :

Note

• Still Image Skip function not available with all discs.

Bonus Group playback (DVD-Audio only)

Some DVD-Audio discs contain bonus groups. To enjoy these groups you may have to enter a password. Refer to the disc's jacket.

1

Note

Press

DISPLAY in stop mode to display “On-Screen Displays.”

• During playback, Bonus Group tracks cannot be selected.

2

GROUP

TRACK

: 2

: 1

DVD-AUDIO

00 : 12 : 34

Press

to select “GROUP,” and press SET.

Press

or NUMBER keys to select bonus group number, and press SET (see pp. 44, 45.)

SELECT :

SET : SET NEXT : D I SPLAY

Notes

• If the proper secret code is already entered, Bonus Group tracks can be selected. (Secret code enter screen is skipped.)

3

Note

BONUS GROUP

ENTER 4-D I G I T CODE

---

Press NUMBER keys

to enter bonus group secret code.

To Make Corrections

Press repeatedly to move the cursor.

Press

NUMBER keys to make the correction.

• When the proper secret code has been entered, Bonus Group track 1 playback begins. If a mistake is made, the secret code enter screen is redisplayed.

4

Press

CLEAR to return to normal screen.

41

D4754S P36-72 (040202).p65

41 2004/02/02, 13:22

DVD-RAM Operation (DVD-RAM only)

You can enjoy playing your personally recorded/edited DVD-RAM discs on this DECK.

Note

• This DECK was designed for playback only. DVD-RAM recording is not possible.

Play a DVD-RAM

1

Do steps 1 ~ 3 on page 22.

• Play begins from the first program title recorded on the DVD-RAM.

2

Press

D.NAVI* or PLAY LIST to display Direct

Navigator or Play List menu for easy title or scene selection.

• See below for “Direct Navigator” or next page for

“Play List information”.

3

4

Press

STOP to stop playing.

Press


Direct Navigator

If the DVD-RAM features Direct Navigator, a list of recorded titles is displayed. Simply select a title number and start playback. (Operation can vary with disc used.)

1

Press D.NAVI

in Play/Stop mode to display the Direct Navigator menu.

Program No.

Recording time length

Page No.

2

Press to select a page and press to select a title (Program No.).

Then, press SET or PLAY to start playing.

• “Pressing SET or PLAY” is not necessary when using NUMBER keys.

Using NUMBER keys starts playing automatically.


<Input

Example>

1 digit number 1 ••••1


➛ 1 ➛ 2

Direct Navigator

No.

1

2

3

4

Date

2002/12/24

5:15:41AM

2002/12/25

4:31:49AM

2002/12/25

8:24:25AM

2002/12/25

12:45:00AM

Length

00:01:00

00:03:12

00:15:01

00:03:00

SELECT:

SET : SET

Title

Drama

Dinosaur

Page 1/4

Pana NEWS

Tigers vs.Giants

END:TITLE

Recording time and date

Titles

(Example)

3

Press

D.NAVI to clear Direct navigator menu.

42


D4754S P36-72 (040202).p65

42 2004/02/02, 13:22


Play List

If the DVD-RAM features a Play List, your preselected list of favorite scenes is displayed for easy access. (Operation can vary according to how you edited the DVD-RAM.)

1

Press PLAY LIST

in Play/Stop mode to display the Play List menu.

Play List No.

Established time length

Page No.

2

Press to select a page and press to select a title (Play List No.).

Then, press SET or PLAY to start playing.

• “Pressing SET or PLAY” is not necessary when using NUMBER keys.

Using NUMBER keys starts playing automatically.


<Input

Example>

1 digit number 1 ••••1


➛ 1 ➛ 2

Play List

No.

1

2

3

4

Date

2002/12/24

5:15:41AM

2002/12/25

4:31:49AM

2002/12/25

8:24:25AM

2002/12/25

12:45:00AM

Length

00:01:00

00:03:12

00:15:01

00:03:00

SELECT:

SET :SET

Page 1/5

Title

Movie Picture

Playback

Still Picture

Playback

Hybrid Playback

Par tial Playback

END:MENU

Recording time and date

Titles

(Example)

3

Press

PLAY LIST to clear Play List menu.

10

NUMBER keys

SELECT

SET

PLAY LIST

STOP

PLAY

D.NAVI

Notes

• Titles of Direct Navigator and Play List cannot be changed using this DECK.

• With Direct Navigator, up to 99 programs can be displayed. With Play List, up to 99 titles (999 scenes) can be displayed.

• While DVD MAIN MENU is displayed, Direct Navigator and Play List display will not appear even if TITLE or MENU is pressed.


43

D4754S P36-72 (040202).p65

43 2004/02/02, 13:22

DVD Operation using On-Screen Displays

When

DISPLAY is pressed, On-Screen Displays show disc information (title/chapter/track number, elapsed playing time) and DECK information (repeat play, play mode).

1

Press

DISPLAY* in Play or Stop mode to display “On-Screen Displays.”

• Each press of DISPLAY changes the on-screen display as follows. (Refer to pp. 44 ~ 48.)

➡

Selected Disc information

(See pp. 45, 46.)

Selected DECK information

(See pp. 47, 48.)

Ready Checklist


NUMBER keys

Normal Screen

Note

• DISPLAY button does not function while main menu of

DVD, title menu of DVD, Direct Navigator or Play List is displayed.

2

3

Press

(or ) to select an item, and

press

SET.

Press

or

NUMBER keys

to select the setting, and press

SET.

<Example of DVD-Video>

• When numbers are displayed (e.g. title number), NUMBER keys are also available.

• If the number entered is not on the disc, the entry will have no effect.

Re-enter the correct number.

<Example of DVD-Audio>

• For more details, refer to the disc operation information.

To return to normal screen, press DISPLAY

repeatedly.

SELECT

SET

DISPLAY

<Example of DVD-RAM>

44

Note



D4754S P36-72 (040202).p65

44 2004/02/02, 13:22


Detailed Descriptions of each On-Screen Display

1. TITLE No.

Go directly to a preset title number.

• Select “TITLE”, and press SET.

• Change the No. by pressing or NUMBER keys, and press SET.

1

2

2. CHAPTER No.

Go directly to a preset chapter number.

• Select “CHAPTER”, and press SET.

• Change the No. by pressing or

NUMBER keys, and press SET.

• This function does not work with some discs.

3. Disc currently being played

The type of disc currently inserted is displayed.

4. Elapsed playing time

The screen may be changed by selecting the elapsed time.

• Select the elapsed playing time (“xx:xx:xx”), and press SET.

• Change the elapsed time by pressing

NUMBER keys.

Enter time starting with seconds.

If the time entered is not on the disc, the entry will have no effect.

Re-enter the correct time.

e.g., press 0

➛ 1 ➛ 2 ➛ 3 ➛ 4 ➛ 5 ➛ SET for “01 : 23 : 45”.

press 3

➛ 0 ➛ SET for “00 : 00 : 30”.


3

4

A. GROUP No.

Go directly to a preset group number.

• Select “GROUP”, and press SET.


B. TRACK No.

Go directly to a preset track number.

• Select “TRACK”, and press

SET.


A

B

C. Disc currently being played


D. Elapsed playing time



• Change the elapsed time by pressing NUMBER keys.




e.g., press 0

➛ 1 ➛ 2 ➛ 3 ➛ 4 ➛ 5 ➛ SET for “01 : 23 : 45”.

press 3

➛ 0 ➛ SET for “00 : 00 : 30”.


C

D

45

D4754S P36-72 (040202).p65

45 2004/02/02, 13:22

DVD Operation using On-Screen Displays (continued)

2

3

1. TRACK No.

Go directly to a preset track number.

• Select “TRACK”, and press SET*.


1

2. Disc currently being played


3. Elapsed playing time

A

A. Direct Navigation (PROGRAM) or PLAY LIST No.

Go directly to a preset title number.

• Select “PROGRAM” or “PLAY LIST”, and press

SET.


B. Disc currently being played


C. Elapsed playing time



• Change the elapsed time by pressing NUMBER keys.




e.g., press 0

➛ 1 ➛ 2 ➛ 3 ➛ 4 ➛ 5 ➛ SET for “01 : 23 : 45”.

press 3

➛ 0 ➛ SET for “00 : 00 : 30”.


A

Direct Navigation

(PROGRAM)

PLAY LIST

B

C

B

C

Note


46


D4754S P36-72 (040202).p65

46 2004/02/02, 13:22


1. Operating mode

The current operation is displayed.

1

2

2. Repeat Play mode (see p. 48)

Repeat play mode can be selected.

• Select “REPEAT”, and press SET.

• Change the desired mode during play by pressing , and press SET.

Repeat Play mode

DVD-Video

DVD-Audio

CHAPTER

TRACK

TITLE

GROUP

OFF (NORMAL)

OFF (NORMAL)

DVD-RAM

(PROGRAM)

PROGRAM DISC

(PLAY LIST)

OFF (NORMAL)

PLAY LIST ALL PLAY LIST OFF (NORMAL)

CD TRACK DISC OFF (NORMAL)

3. Play mode [CD only] (See p. 39, 40.)

When Play mode is set (p. 39, 40), the mode name is displayed.

PROGRAM PLAY program play

RANDOM PLAY random play

---normal play

3

Note

• For repeat play in VCR mode, see p. 31.

NUMBER keys

SELECT

SET

D4754S P36-72 (040202).p65

47 2004/02/02, 13:22

47

DVD Operation using On-Screen Displays (continued)

For your reference

Repeat Play mode example (see p. 47)

• CHAPTER/TITLE REPEAT PLAY (DVD-Video)

CURRENT PLAYBACK POSITION

CHAPTER REPEAT

TITLE REPEAT

NORMAL PLAY

TITLE chapter chapter chapter

• TRACK/GROUP REPEAT PLAY (DVD-Audio)


TRACK REPEAT

GROUP REPEAT

NORMAL PLAY

GROUP track track track

GROUP track track track

• TRACK/DISC REPEAT PLAY (CD)

CURRENT PLAYBACK POSITION track track track

TRACK REPEAT

DISC REPEAT

NORMAL PLAY

• PROGRAM/DISC REPEAT PLAY (DVD-RAM [PROGRAM])


PROGRAM REPEAT

DISC REPEAT

NORMAL PLAY

PROGRAM PROGRAM PROGRAM PROGRAM PROGRAM PROGRAM

• PLAY LIST/ALL PLAY LIST REPEAT PLAY (DVD-RAM [PLAY LIST])


POWER

OPEN/

CLOSE

PLAY LIST REPEAT

ALL PLAY LIST REPEAT

NORMAL PLAY

PLAY LIST PLAY LIST PLAY LIST PLAY LIST PLAY LIST PLAY LIST

Note

• For repeat play in VCR mode, see p. 31.


48


D4754S P36-72 (040202).p65

48 2004/02/02, 13:23

NUMBER keys

ACTION

SELECT

SET

PLAY

STOP

SKIP+

SKIP

-

FF

REW

PAUSE

MP3/WMA/JPEG Playback Operation

This unit can play MP3/WMA/JPEG format CD-R or CD-RW recorded for personal use on a PC, etc.

Some discs may not play due to the condition of the recording.

1

Press

POWER* on the remote or DECK.

2

Press OPEN/CLOSE,

then place an MP3/WMA/JPEG disc into the disc tray.

Press

OPEN/CLOSE to close.

3

• MP3/WMA/JPEG MENU is displayed.

• Playback starts automatically

(except JPEG files).

• CD directory is displayed.

<Example>

Function

Status

STOP

Folder area

(Current folder appears green.)

ROOT . .

VA END_WALTZ

TECHNO DD_CUB I C

POPS NOCTURNE

JAZZ NORN

Parent folder

File area

(Selected file/

PLAY MODE : NORMAL folder is highlighted.

Titles are

PLAY MODE

:MP3 file :WMA file

displayed up to 11 characters.)

:Folder :Parent folder

:JPEG file

MP3/WMA Playback

Do steps 1~3 at left.

a

Press

to select an MP3/WMA file (

/

)

.

(During STOP mode)

b

Press

SET or PLAY to start playback.

■ Forward/Reverse Search

Press

FF/SLOW+ or REW/SLOW- during play.

Press


• Search speed, slow at first, increases with each additional press of the button up to 5 levels.

■ Forward/Reverse Track Skip

Press

SKIP+ | or

SKIP- |

during play.

Each press skips a track.

• If pressed within first 3 seconds of playback, skips to the previous track. If over 3 seconds, returns to top of track. (

SKIP- |

only.)

• Put DECK in Stop mode before performing folder/file selection (see step 4.)

■ Pause

Press

PAUSE during play.

c

Press


Press

STOP to stop play.

d

Press


The MP3/WMA/JPEG MENU is closed automatically.

<Example>

ROOT

VA

END_WALTZ

DD_CUB I C

NOCTURNE

NORN

TECHNO

POPS

(Diagram left shows CD directory structure as displayed in example

OSD above.)

Notes

• Only File (not Folder) area operation is possible.

• Files are displayed in the following order:

(!...0,1....9,A,B......Z).

Note

• Copyright protected files and files containing errors cannot be played back. The DECK skips to the next file.

JAZZ

4

• Select file (During STOP mode)

1) Press to select an MP3/WMA file ( / ).

➡ MP3/WMA Playback (see right)

2) Press to select a JPEG file ( ).

➡ JPEG Playback (see p. 50)

3)

Press

SKIP+ | (next) or

SKIP- |

(previous) to skip a file/folder page (7 files) in the File area.

• Select folder (During STOP mode)

1) Press to select a folder ( ).

2) Press SET to display files/folders contained in the folder.

• Select parent folder (During STOP mode)

1) Press to select a folder ( ).

2) Press SET to make changes to the previous directory display.

5

Press

ACTION to return the DVD MAIN

MENU. (

➛ Press ACTION again to return to the MP3/WMA/JPEG MENU.)

■ Select PLAY MODE [MP3/WMA Playback]

(During STOP mode)

Press to select the desired PLAY

MODE (see below).

[PLAY MODE]

NORMAL:

All MP3/WMA files are selected and played back one time only.

SINGLE REPEAT:

The selected MP3/WMA file is played back repeatedly.

FOLDER REPEAT:

The MP3/WMA files contained in the selected folder are played back repeatedly. However, folders below the selected folder are not played back.

DISC REPEAT:

All MP3/WMA files are played back repeatedly.

49

D4754S P36-72 (040202).p65

49 2004/02/02, 13:23

MP3/WMA/JPEG Playback Operation (continued)

JPEG Playback

You can play back JPEG images.

Displayable Image Size: 32x32~7680x7680 pixels

Note

• Some JPEG format may not be played back.

Do steps 1~3 on page 49.

1

Press

to select a JPEG file (

)

.

2

Press SET or PLAY.

Selected JPEG file is displayed.

[JPEG Playback Screen]

<Example>

3

➡

Press STOP

.

(See p. 49)

■ Next/Previous Search

➡

Press

SKIP+ | or

SKIP- |

.

■ Start Slide-show

➡

Press

REW/SLOW-. (below)

FF/SLOW+ or

■ Enlarging an image

■ Rotating an image

➡

Press

ZOOM. (P. 51)

➡

Press

ANGLE. (P. 51)

Press STOP to return to the MP3/WMA/

JPEG MENU.

■ Select PLAY MODE [JPEG Slide-show]

(During STOP mode)

Press to select the desired PLAY MODE

(See below).

[PLAY MODE]

NORMAL:

All JPEG files are selected and played back one time only.

SINGLE REPEAT:

The selected JPEG file is played back repeatedly.

FOLDER REPEAT:

The JPEG files contained in the selected folder are played back repeatedly. However, folders below the selected folder are not played back.

DISC REPEAT:

All JPEG files are played back repeatedly.

JPEG Slide-show

(During JPEG Playback.)

JPEG files are displayed automatically

(about every 3 seconds) as a slide-show.

1

Press

FF/SLOW+ or REW/SLOW-.

<Example>

<Example>

Operation can be done when files are in order, such as in the diagram below.

ROOT

REW/SLOW-

01 PIC

FF/SLOW+

Image changes every 3 seconds.

➡

Press

STOP to return the MP3/WMA/

JPEG MENU. (See p. 49)

■ Still picture

➡

Press

STILL (only SLIDE).

➡

Press


■ Forward/Reverse File Skip

➡

Press

SKIP+ | or

SKIP- |

.

Each press skips a file.

AAA

DDD

TTT

UUU

VVV

WWW

ZZZ

REW/SLOW-

FF/SLOW+

2

50

Press ACTION to return to

the DVD MAIN MENU.


D4754S P36-72 (040202).p65

50 2004/02/02, 13:23

SELECT

SET

FF/

SLOW+

REW/

SLOW-

STILL

ANGLE

JPEG Zoom


You can enlarge specific portions of a JPEG picture and select the zoom ratio using the ZOOM button on the remote during JPEG Playback screen.

ACTION

Set Zoom size.

Press

ZOOM repeatedly to change display as follows.

➡

Press

STOP to return the MP3/WMA/JPEG MENU.

• You can enlarge the center portion of the image to one of 2 magnifications.

• Operation can be done during Rotation (below).

X 1.0 (ORIGINAL) X 1.5 (ZOOM 1) X 2.0 (ZOOM 2)

STOP

1st press 2nd press

PLAY

SKIP+

SKIP -

ZOOM

3rd press

■ Use the , , and buttons to move the position up, down, left and right.

(Position cannot be changed on X1.0

ORIGINAL images.)

1st press

JPEG Rotation


You can rotate a JPEG picture using the ANGLE button on the remote during JPEG Playback screen. (The JPEG picture will be rotated 90 ° clockwise.)

Set rotation.

Press

ANGLE repeatedly to change display as below.

➡

Press STOP to return the MP3/WMA/JPEG MENU.

• Operation can be done during Zoom (above).

• The vertical/horizontal ratio of rotated JPEG images may vary when they are displayed.

2nd press 3rd press

4th press

MPEG Layer-3 audio decoding technology licensed from Fraunhofer IIS and

Thomson multimedia.

Windows Media, and the Windows logo are trademarks, or registered trademarks of Microsoft Corporation in the United States and/or other countries.

WMA is a compression format developed by Microsoft Corporation. It achieves the same sound quality as MP3 with a file size that is smaller than that of MP3.

D4754S P36-72 (040202).p65

51 2004/02/02, 13:23

51

Settings for DVD Operation

1

Press ACTION*


2

DVD MAIN MENU

D I SC LANGUAGES

AUDIO OUTPUT

ST I L L MODE

TV MODE

: AUTO

: 4 : 3 P a n & S c a n

PROGRESSIVE OUT : OFF

Once initial settings are done, they remain in memory (even after power is turned off) until changed. This means

DECK will operate under the same conditions (especially DVDs) each time.

Press


press

SET.

Ready Checklist


SELECT

SET

END

:

: SET

: ACT I ON

DISC LANGUAGES (See below)

All languages offered on the disc can be set.

If a language not offered is set, the original disc language will be selected.

AUDIO OUTPUT (See p. 53.)

You can set the audio output that comes from the digital audio output terminal.

STILL MODE (See p. 54.)

To select “FIELD” (Field still) or “FRAME” (Frame still) to prevent jitter or make small text or fine patterns clearly visible in a still picture.

When “AUTO” is set, “FIELD” or “FRAME” is selected automatically.

TV MODE (See p. 54.)

To select whether the video material for a widescreen will be played back in the Pan & Scan style,

Letterbox style or 16 : 9 style.

To select and set the language of the audio soundtrack, subtitles, or title/DVD menus for all discs to be played.

3

4

5

Disc Languages (DVD only)

DVD MAIN MENU

D I SC LANGUAGES

AUDIO OUTPUT

ST I L L MODE

TV MODE

: AUTO

: 4 : 3 P a n & S c a n


SELECT

SET

END

:

: SET

: ACT I ON

D I SC LANGUAGES

AUD I O

SUBT I TLE

MENUS

: E n g l i s h

: AUTO

: E n g l i s h

SELECT

SET

END

:

: SET

: ACT I ON

Press

to select

“DISC LANGUAGES,” and

press SET

to display screen.

Press


press

SET repeatedly for desired language.

(Please refer right.)

Press

ACTION to redisplay DVD MAIN

MENU and go to step 2 to setup another item.

Or, press ACTION twice to exit.

NUMBER keys

ACTION

SELECT

SET

“AUDIO” selections

(Factory preset: English)

To select the audio soundtrack language.

English/Spanish/French/Japanese

Original: Original disc language

OTHER 0000: Other language selection* 1

“SUBTITLE” selections

(Factory preset: AUTO)

To select the subtitle language.

AUTO: Same language selected for “AUDIO”

• If language set for “AUDIO” is used in playback, subtitles will not appear.

• If another language is used during playback, the subtitles will appear in the language selected at “AUDIO” setup.



“MENUS” selections

(factory preset: English)

To select the language used in title menus or DVD menus.



To enter OTHER

✱✱✱✱ code number,

Press

NUMBER keys (Please refer to language codes on p. 56).

To make corrections, press repeatedly to delete language code number, and correct.

*

1

If the selected language is not offered, the original disc language is selected.


52

D4754S P36-72 (040202).p65

52 2004/02/02, 13:23


Audio Output (DVD only)

Ready Checklist


Select the digital output to be output from the optical digital audio output connector of DECK.

1 Press ACTION


Type of amplifier

to be connected

Recommended setting

LPCM

( DV D )

D o l b y

Digital

D T S

2

DVD MAIN MENU

D I SC LANGUAGES

AUDIO OUTPUT

ST I L L MODE

TV MODE

: AUTO

: 4 : 3 P a n & S c a n


SELECT

SET

END

:

: SET

: ACT I ON

Press

to select

“AUDIO OUTPUT,” and

press SET

to display screen.

No amplifier is connected

AV amplifier (with digital audio input connector) without Dolby Digital/DTS decoder

AV amplifier including

Dolby Digital decoder

AV amplifier including

Dolby Digital/DTS decoder

P C M

P C M

P C M

PCM*

1

Bitstream

Bitstream Bitstream

*

2

3

AUD I O OUTPUT

LPCM(DVD) : OFF

D o l b y D i g i t a l : B i t s t r e a m d t s : B i t s t r e a m

DRC : OFF

SELECT

SET

END

:

: SET

: ACT I ON

Press


press SET

repeatedly for output. (See below.)

OFF: Linear PCM of less than 44.1 or 48 kHz/16 bit is output. When playing DVDs recorded in linear PCM of over 44.1 or 48 kHz/20 bit, no digital audio is output. (Factory preset)

PCM: When playing DVDs recorded in linear PCM of

44.1 or 48 kHz/20 bit/24 bit or more, digital audio converted to 44.1 kHz/16 bit or 48 kHz/

16 bit is output.

(Digital output of PCM audio is restricted to

48 kHz/16 bit or below for copyright protection.)

Bitstream: Dolby Digital bitstream (1 ch - 5.1 ch) is output. (Factory preset)

PCM: When you have connected an amplifier that doesn’t have a built-in Dolby Digital decoder.

• Make settings according to amplifier connected to optical audio output as shown in above table.

*1 When connecting an amplifier (with an optical digital input connector) which does not contain the Dolby Digital or

DTS decoder, be sure to select

“PCM”. If “Bitstream” is selected, starting DVD play may cause such a high level of noise as to be harmful to your ears and damage the speakers.

*2 When a dts decoder is connected, please select “Bitstream” in “dts.”

If “PCM” is selected, there will be stereo sound.

When a Dolby Digital decoder is connected, please select “Bitstream” in “Dolby Digital.”

If “PCM” is selected, there will be stereo sound.

PCM*

1

P C M

Bitstream: DTS bitstream is output. (Factory preset)

PCM: When you have connected an amplifier that doesn’t have a built-in DTS decoder.

■ “DRC (Dynamic Range Compression)”

selections

OFF: Normal audio range is selected. (Factory preset)

ON:

For dynamic sound even at low volume, this is useful for late-night listening.

[Dolby Digital DVDs only].

4

Press

ACTION to redisplay DVD MAIN

MENU and go to step 2 to setup another item.

Or, press ACTION twice to exit.

53

D4754S P36-72 (040202).p65

53 2004/02/02, 13:23

Settings for DVD Operation (continued)

Still Mode (DVD only)

Set to reduce jitter in a displayed still picture or a motion picture.

1

Press ACTION*


2

DVD MAIN MENU

D I SC LANGUAGES

AUDIO OUTPUT

ST I L L MODE

TV MODE

: AUTO

: 4 : 3 P a n & S c a n


Press

to select “STILL MODE,” and

press

SET repeatedly for mode. (See below.)

SELECT

SET

END

:

: SET

: ACT I ON

AUTO:

“FIELD” (Field still) or “FRAME” (Frame still) is automatically selected during the still mode.

(Factory preset)

FIELD: “FIELD” (Field still) is always selected.

This setting will reduce jitter when compared with “AUTO” on some discs.

FRAME: “FRAME” (Frame still) is always selected.

Some texts and fine patterns will be seen clearly when compared with “AUTO” on some discs.

3

Press ACTION

to exit this mode.

ACTION

SELECT

SET

TV Mode (DVD only)

Set the screen display style for wide-screen video material playback.

1

Press

ACTION


2

DVD MAIN MENU

D I SC LANGUAGES

AUDIO OUTPUT

ST I L L MODE

TV MODE

: AUTO

: 4 : 3 P a n & S c a n


Press

to select “TV MODE,” and press

SET

repeatedly for mode.

(See below.)

SELECT

SET

END

:

: SET

: ACT I ON

4:3 Pan & Scan (Factory preset) :

Wide-screen video data is played in Pan & Scan style (left and right of screen is trimmed.)

• Video data not formatted in Pan & Scan will play in letterbox style.

4:3 Letterbox :

Wide-screen video data is played in Letterbox style (top and bottom of screen has black margin).

16:9 :

Set “16:9” when using Wide-screen TV.

Example

• Pan & Scan (Factory preset)

• Letterbox

3

Press ACTION

to exit this mode.


54

D4754S P36-72 (040202).p65

54 2004/02/02, 13:23


PROGRESSIVE OUT

Sets the Component Video Output Connector (p. 10, 13) to output the Progressive scan signal.

1

Press ACTION


2

DVD MAIN MENU

D I SC LANGUAGES

AUDIO OUTPUT

ST I L L MODE

TV MODE

: AUTO

: 4 : 3 P a n & S c a n


Press

to select

“PROGRESSIVE OUT,” and

press

SET repeatedly for mode. (See below.)

SELECT

SET

END

:

: SET

: ACT I ON

OFF:

Progressive scan signal is not output.

ON:

Progressive scan signal is output from the

Component Video Output Connector.

3

Press ACTION

to exit this mode.

Notes

• If the television is not progressive compatible, a progressive scan picture is not available. Connect the Video Output or

S-Video Output connector (see p. 12, 13) and set PROGRESSIVE OUT to “OFF”.

• CONSUMERS SHOULD NOTE THAT

NOT ALL HIGH DEFINITION

TELEVISION SETS ARE FULLY

COMPATIBLE WITH THIS PRODUCT

AND MAY CAUSE ARTIFACTS TO BE

DISPLAYED IN THE PICTURE. IN CASE

OF 525 PROGRESSIVE SCAN PICTURE

PROBLEMS, IT IS RECOMMENDED

TO SET PROGRESSIVE OUT TO “OFF”.

IF THERE ARE QUESTIONS

REGARDING OUR TV SET

COMPATIBILITY WITH THIS MODEL

525p DVD/VCR DECK, PLEASE

CONTACT OUR CUSTOMER SERVICE

CENTER.

A/V OPTIMIZER

You can set to preset audio/video effects as desired.

1

NORMAL

Press

A/V OPTIMIZER

in Play mode to display the A/V OPTIMIZER selection on-screen.


5 seconds.

2

C I NEMA

Press A/V OPTIMIZER

to select the desired mode below.

NORMAL CINEMA

ACTION

DRAMA

The video/audio effect of each mode is listed below.

Mode

NORMAL

Video

Standard video

CINEMA

DRAMA

ACTION

Bright areas are subdued.

Standard video

Brightness and sharpness are enhanced.

Audio

Standard audio

Enhances high/low range for dynamic sound.

Reduces high/low range so dialog and vocals can be heard clearly.

Enhances high/low range for dynamic sound.

ACTION

SELECT

SET

A/V

OPTIMIZER

Note

• With some discs, the audio/video effect may not be obtained, also the audio/video effects may not work well.

55

D4754S P36-72 (040202).p65

55 2004/02/02, 13:23

Language Code List

Enter the appropriate code number for the initial settings “AUDIO”, “SUBTITLE” and/or

“MENUS” (see p. 52).

Code Language

6565 Afar

6566 Abkhazian

6570 Afrikaans

6577 Ameharic

6582 Arabic

6583 Assamese

6588 Aymara

6590 Azerbaijani

6665 Bashkir

6669 Byelorussian

6671 Bulgarian

6672 Bihari

6678 Bengali; Bangla

6679 Tibetan

6682 Breton

6765 Catalan

6779 Corsican

6783 Czech

6789 Welsh

6865 Danish

6869 German

6890 Bhutani

6976 Greek

6978 English

6979 Esperanto

6983 Spanish

6984 Estonian

6985 Basque

7065 Persian

7073 Finnish

7074 Fiji

Code Language

7079 Faroese

7082 French

7089 Frisian

7165 Irish

7168 Scots Gaelic

7176 Galician

7178 Guarani

7185 Gujarati

7265 Hausa

7273 Hindi

7282 Croatian

7285 Hungarian

7289 Armenian

7365 Interlingua

7378 Indonesian

7383 Icelandic

7384 Italian

7387 Hebrew

7465 Japanese

7473 Yiddish

7487 Javanese

7565 Georgian

7575 Kazakh

7576 Greenlandic

7577 Cambodian

7578 Kannada

7579 Korean

7583 Kashmiri

7585 Kurdish

7589 Kirghiz

7665 Latin

Code Language

7678 Lingala

7679 Laothian

7684 Lithuanian

7686

Latvian, Lettish

7771 Malagasy

7773 Maori

7775 Macedonian

7776 Malayalam

7778 Mongolian

7779 Moldavian

7782 Marathi

7783 Malay

7784 Maltese

7789 Burmese

7865 Nauru

7869 Nepali

7876 Dutch

7879 Norwegian

7982 Oriya

8065 Panjabi

8076 Polish

8083

Pashto, Pushto

8084 Portuguese

8185 Quechua

8277

Rhaeto-Romance

8279 Romanian

8285 Russian

8365 Sanskrit

8368 Sindhi

8372

Serbo-Croatian

8373 Singhalese

Code Language

8375 Slovak

8376 Slovenian

8377 Samoan

8378 Shona

8379 Somali

8381 Albanian

8382 Serbian

8385 Sundanese

8386 Swedish

8387 Swahili

8465 Tamil

8469 Telugu

8471 Tajik

8472 Thai

8473 Tigrinya

8475 Turkmen

8476 Tagalog

8479 Tonga

8482 Turkish

8484 Tatar

8487 Twi

8575 Ukrainian

8582 Urdu

8590 Uzbek

8673 Vietnamese

8679 Volapük

8779 Wolof

8872 Xhosa

8979 Yoruba

9072 Chinese

9085 Zulu

56


D4754S P36-72 (040202).p65

56 2004/02/02, 13:23

Warning and Instruction Displays

These displays will alert you to a missed operation or provide further instructions.

OSD

PLEASE SET CLOCK BY

PRESSING ACTION KEY

PLEASE PREPARE

FOR TIMER REC

CHECK CASSETTE

RECORD TAB

NO CASSETTE

TO CANCEL TIMER REC

HOLD DOWN STOP KEY

FOR APPROX 3 SEC

VIDEO HEADS MAY

NEED CLEANING

PLEASE INSERT HEAD

CLEANING CASSETTE

OR REFER TO MANUAL

END : PLAY

VCR LOCK ACTIVATED

REMOTE CONTROL IS SET

TO TV MODE

USE VCR : VCR KEY

USE DVD : DVD KEY

PLEASE CHECK THE DISC,

AND FOR STAINS OR

SCRATCHES ON DISC

THIS DISC MAY NOT BE PLAYED

IN YOUR REGION

THIS TYPE OF DISC CANNOT BE

PLAYED. PLEASE INSERT A

DIFFERENT DISC

CANNOT PLAY THIS FILE

THIS FILE IS PROTECTED

Caution

If you attempt to set or review a Timer

Recording and the Clock is not set...

If the DECK is not in Stop mode, or cassette is not inserted, or cassette has no record tab, or tape is at its end 2 minutes before a Timer

Recording is about to begin...

If you press REC on the remote control or DECK, and a cassette is inserted with no record tab...

If you press PLAY, FF, REW, or REC on the remote control or DECK without a cassette inserted...

If you press STOP or POWER during a Timer

Recording...

(visible in VCR mode only)

If head cleaning becomes necessary while playing back a tape...

Page

24

24

25

6

20

21

25

4

If you press a function button other than STOP/

EJECT or POWER while DECK is in VCR Lock mode...

If you press an invalid key on the remote while in TV mode...

32

28

29

34

If you press PLAY, and DECK reads data from a stained or scratched disc in DVD mode.

6

Playback of a disc with different region number was attempted. Only discs marked region “1”,

“ALL”, or those that include “1” are playable on this DECK.

An unusable disc is inserted in the unit, or the disc is not installed with label side up.

3

6

This file format cannot be played.

(Appears during MP3/WMA/JPEG file playback)

This file is copyright protected and cannot be played back. (Playback is prohibited.)

(WMA only)

49

49

2004/02/02, 13:23

57

D4754S P36-72 (040202).p65

57

Before Requesting Service

Check the following points if you are having trouble with your DECK.

Power

No power…

Power turns itself off...

Recording & Playback

TV program cannot be recorded...

Solution

• Completely insert Power Plug into an AC outlet.

• Press POWER button on.

• Make sure power source is active.

• Auto power-off (shutoff) occurs after about 5 min.

in DVD mode with no operation, or if there is no broadcast signal in TV or Playback mode.

Turn the power back on. (pp. 23, 33)

Solution

• Check connections between DECK, external antenna, and TV.

• Check channel selections.

• Make sure your antenna system (CABLE or TV) is correctly set. (Channels [p. 18])

• Make sure cassette record tab is intact. (p. 6)

Timer recording cannot be performed…

There is no playback picture, or the playback picture is noisy or contains streaks...

During special effects playback picture may contain some vertical jitter when using a TV with an

Automatic Vertical Hold Control...

• Confirm that clock is set to current time and date.

• Make sure Cable/DSS box (if used) is left on and tuned to channel to be recorded.

• Set recording start/stop times correctly. (p. 24)

• Timer recording may not be performed or continued if a power interruption occurs before or during a

Timer Recording, even after power is restored.

• Select channel 3 or 4 on TV to match VCR output channel (3 or 4) (p. 16) or select LINE.

• Set VCR/TV selector to “VCR.”

• Adjust TRACKING control in either direction. (p. 4)

• Try Head Cleaning. (p. 4)

• Set TV’s Vertical Hold Control to MANUAL, then adjust.

DECK cannot be controlled...

Remote Control

DECK cannot be remote controlled...

PROG buttons do not respond...

• Make sure DECK power is on.

• Check Remote batteries.

• Make sure VCR LOCK is set to off. (p. 32)

• Make sure Remote is in proper mode. (p. 28)

• Make sure Timer Recording is not in progress.

Solution

• Make sure DECK power is on.

• Make sure Remote is in VCR mode.

• Aim Remote Control directly at remote sensor on DECK. (p.9)

• Avoid any object blocking signal path.

• Check Remote batteries. (p. 4)

• Exposing DECK remote sensor to direct fluorescent or outdoor light may cause signal interference.

• PROG functions are not available in COMPONENT

Video Output and S-VIDEO OUT. Set TV to either RF

IN or VIDEO IN. (p. 10)

• Check Remote batteries. (p. 4)

• Press VCR or DVD button for DVD/VCR mode. (p. 28)

58


D4754S P36-72 (040202).p65

58 2004/02/02, 13:23

DVD/ CD

Play fails to start even when PLAY is pressed...

Picture is distorted during rapid advance or rapid reverse...

No Forward/Reverse Scene Search play...

Audio soundtrack and/or subtitle language is not the one selected at the initial settings...

No subtitles...

Alternative audio soundtrack

(or subtitle) language cannot be selected...

Angle cannot be changed...

Solution

• This DECK cannot play discs other than DVDs and CDs.

• The disc may be dirty and require cleaning.

• The picture will be somewhat distorted at times: this is normal.

• Some discs may have sections which prohibit

Forward/Reverse Scene Search. (p. 23)

• If the audio soundtrack and/or subtitle language selected at DVD initial settings does not exist on the disc, it will not be accessible.

• Subtitles appear only when available on disc.

• “OFF” is selected at the changing subtitle language.

Select “ON” at the “Subtitle Languages” section

(p. 36) to display the subtitles.

• Alternative language cannot be selected with discs which do not contain more than one language.

• For some discs, alternative language cannot be selected with the AUDIO or SUB TITLE button.

Try selecting it from the DVD MAIN MENU if available.

• This function is dependent on software availability.

Even if disc has multiple angles, they may be recorded for specific scenes only (ANGLE indicator on DECK lights up). (p. 37)

Miscellaneous

Programs cannot be viewed on TV...

Video cassette cannot be inserted...

Solution

• Make sure TV is tuned to VCR's output channel (3 or 4).

• Check connections between DECK, external antenna, and TV.

• Set VCR/TV selector to “TV.” (p. 21)

• Make sure proper signal source is selected.

• If the television is not progressive compatible, a progressive scan picture is not available.

Connect the Video Output or S-Video Output connector (pp. 12, 13) and set PROGRESSIVE

OUT to “OFF” in the DVD Main Menu. (p. 55)

• Insert the cassette with window side up; record tab facing you.

• Make sure cassette record tab is intact. (p. 6)

Video cassette ejects when a recording is started or the power is turned off for timer recording...

In Stop mode, the motor (CYLINDER) continues to rotate...

The disc cannot be removed..

• To enable Quick play mechanism, the cylinder will rotate for about 3 minutes. This reduces response time from Stop to Play mode.

• First, unplug DECK. Then, prepare a rigid wire

(e.g. an extended paper clip) and, applying moderate force, insert it straight into the hole at the base of the tray. The tray will eject a little. Now, pull the tray all the way out and remove the disc. (p. 9)

If you cannot resolve the problem, please call the Customer Call Center for product assistance at 1-800-211-PANA (7262).

To locate an authorized servicenter, please call toll free 1-800-211-PANA (7262).

or, contact us via the web at:http://www.panasonic.com/contactinfo

59

D4754S P36-72 (040202).p65

59 2004/02/02, 13:23

Limited Warranty

PANASONIC CONSUMER ELECTRONICS COMPANY,

DIVISION OF MATSUSHITA ELECTRIC

CORPORATION OF AMERICA

One Panasonic Way

Secaucus, New Jersey 07094

PANASONIC SALES COMPANY,

DIVISION OF MATSUSHITA

ELECTRIC OF PUERTO RICO, INC.,

AVE. 65 de Infantería, Km. 9.5

San Gabriel Industrial Park

Carolina, Puerto Rico 00985

Panasonic DVD/VCR Deck Limited Warranty

Limited Warranty Coverage

If your product does not work properly because of a defect in materials or workmanship, Panasonic

Consumer Electronics Company or Panasonic Sales Company (collectively referred to as “the warrantor”) will, for the length of the period indicated on the chart below, which starts with the date of original purchase

(“Limited Warranty period”), at its option either (a) repair your product with new or refurbished parts, or (b) replace it with a new or a refurbished product. The decision to repair or replace will be made by the warrantor.

Product or Part Name Parts Labor

DVD/VCR Deck One (1) Year Ninety (90) Days

Rechargeable Batteries

(in exchange for defective item)

Ten (10) Days Not Applicable

During the “Labor” Limited Warranty period there will be no charge for labor. During the “Parts” warranty period, there will be no charge for parts. You must mail-in your product during the warranty period.

If non-rechargeable batteries are included, they are not warranted. This Limited Warranty only applies to products purchased and serviced in the United States or Puerto Rico. This Limited Warranty is extended only to the original purchaser and only covers product purchased as new. A purchase receipt or other proof of original purchase date is required for Limited Warranty service.

Mail-In Service

For assistance in the continental U.S.A. in obtaining repairs please ship the product to:

Panasonic Services Company

Customer Servicenter

Suite B

4900 George McVay Drive

McAllen, TX 78503

For assistance in Puerto Rico call Panasonic Sales Company (787)-750-4300 or fax (787)-768-2910.

When shipping the unit carefully pack and send it prepaid, adequately insured and preferably in the original carton. Include a letter detailing the complaint and provide a day time phone number where you can be reached.

IF REPAIR IS NEEDED DURING THE LIMITED WARRANTY PERIOD THE PURCHASER WILL BE

REQUIRED TO FURNISH A SALES RECEIPT/PROOF OF PURCHASE INDICATING DATE OF

PURCHASE, AMOUNT PAID AND PLACE OF PURCHSE. CUSTOMER WILL BE CHARGED FOR THE

REPAIR OF ANY UNIT RECEIVED WITHOUT SUCH PROOF OF PURCHASE.

Limited Warranty Limits And Exclusions

This Limited Warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES NOT

COVER normal wear and tear or cosmetic damage. The Limited Warranty ALSO DOES NOT COVER damages which occurred in shipment, or failures which are caused by products not supplied by the warrantor, or failures which result from accidents, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty installation, setup adjustments, misadjustment of consumer controls, improper maintenance, power line surge, lightning damage, modification, or commercial use (such as hotel, office, restaurant, or other business), rental use of the product, or service by anyone other than a Factory Servicenter or other Authorized Servicer, or damage that is attributable to acts of God.

60


D4754S P36-72 (040202).p65

60 2004/02/02, 13:23

THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER “LIMITED WARRANTY

COVERAGE”. THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL

DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH

OF THIS WARRANTY. (As examples, this excludes damages for lost time, cost of having someone remove or re-install an installed unit if applicable, travel to and from the servicer, loss of or damage to media or images, data or other recorded content. The items listed are not exclusive, but are for illustration only.)

ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY,

ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY.

Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied Limited Warranty lasts, so the exclusions may not apply to you.

This Limited Warranty gives you specific legal rights and you may also have other rights which vary from state to state. If a problem with this product develops during or after the Limited Warranty period, you may contact your dealer or Servicenter. If the problem is not handled to your satisfaction, then write to the warrantor’s Consumer Affairs Department at the addresses listed for the warrantor.

PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY, ARE YOUR

RESPONSIBILITY.

Customer Services Directory

Obtain Product Information and Operating Assistance; locate your nearest Dealer or

Servicenter; purchase Parts and Accessories; or make Customer Service and

Literature requests by visiting our Web Site at:

http://www.panasonic.com/support

or, contact us via the web at:

http://www.panasonic.com/contactinfo

You may also contact us directly at:

1-800-211-PANA (7262),

Monday-Friday 9 am-9 pm; Saturday-Sunday 10 am-7 pm, EST.

For hearing or speech impaired TTY users, TTY : 1-877-833-8855

Accessory Purchases

Purchase Parts, Accessories and Instruction Books online for all Panasonic

Products by visiting our Web Site at:

http://www.pasc.panasonic.com

or, send your request by E-mail to: [email protected]

You may also contact us directly at:

1-800-332-5368 (Phone) 1-800-237-9080 (Fax Only) (Monday - Friday 9 am to 8 pm, EST.)

Panasonic Services Company

20421 84th Avenue South,

Kent, WA 98032

(We Accept Visa, MasterCard, Discover Card, American Express, and Personal Checks)

For hearing or speech impaired TTY users, TTY : 1-866-605-1277

Service in Puerto Rico

Matsushita Electric of Puerto Rico, Inc. Panasonic Sales Company

Factory Servicenter:

Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park,

Carolina, Puerto Rico 00985

Phone (787)750-4300 Fax (787)768-2910

As of October 2003

61

D4754S P36-72 (040202).p65

61 2004/02/02, 13:23

Medidas de seguridad y precauciones importantes

PARA REDUCIR EL RIESGO DE GOLPES ELÉCTRICOS, INCENDIOS, HERIDAS O DAÑOS A

ESTE PRODUCTO, LEA Y GUARDE TODAS LAS INSTRUCCIONES DE SEGURIDAD Y

FUNCIONAMIENTO. TENGA EN CUENTA TODAS LAS ADVERTENCIAS INDICADAS EN EL

MANUAL Y EN EL PRODUCTO.

INSTALACIÓN

1 PRECAUCIÓN CON LA FUENTE DE ALIMENTACIÓN

El equipo solo debe hacerse funcionar desde una fuente de a limentación que se indique en la unidad o en este manual.

Si fuera necesario, haga revisar la fuente de alimentación de su hogar por parte de la Compañia de Suministro Eléctrico o por parte de su Distribuidor de Productos de Vídeo.

2 CONECTOR POLARIZADO O CON TOMA A TIERRA

Como característica de seguridad, este producto de vídeo viene equipado con un enchufe de cable de alimentación polarizado (solo una pata es más ancha que la otra), o con un enchufe del tipo con toma a tierra de tres patas.

PRECAUCIÓN CON EL ENCHUFE POLARIZADO

Este enchufe sólo entrará en la toma en un sentido.

Si no pudiera introducir el enchufe a fondo, intente darle la vuelta. Si aún así no entrara, llame a un técnico electricista para que le instale una toma de red adecuada. No desactive esta función de seguridad manipulando el enchufe de ninguna manera.

PRECAUCIÓN CON ENCHUFES CON TOMA A TIERRA

Este enchufe sólo entrará en una toma con conexión a tierra de tres orificios. Si fuera necesario, que un técnico electricista le instale la toma de red adecuada. No desactive esta función de seguridad manipulando el enchufe de ninguna manera.

3 CABLE DE ALIMENTACIÓN

Asegúrese de que los cables de alimentación son dispuestos de tal forma que no se apoye nada sobre ellos, no ruede nada sobre ellos, o que estén en el paso de tráfico al caminar. Si se utilizara un cable alargador, asegúrese de que también disponga de un enchufe polarizado o con toma a tierra y de que puede conectarse firmemente. Los cables pelados, los enchufes averiados o hilos quebrados constituyen un peligro y deben ser reemplazados por un técnico cualificado del servicio técnico. Las tomas eléctricas de la red general sobrecargadas y los cables de extensión constituyen riesgos de incendio y han de evitarse en lo posible.

4 NO BLOQUEE LOS ORIFICIOS DE VENTILACIÓN

Las aberturas de ventilación del mueble liberan el calor generado durante el funcionamiento de la unidad. Si se bloquearan, el calor acumulado dentro de la unidad podría ocasionar fallos que pueden llevar a riesgos de incendio o daños por calor en las cassettes utilizadas.

5 EVITE UBICACIONES MUY CALIENTES O SOMETIDA

A CAMBIOS BRUSCOS DE TEMPERATURA

No coloque la unidad encima o cerca de cual quier tipo de calefactor o regulador, bajo la luz solar directa, dentro de vehículos, etc… No traslade la unidad súbitamente entre sitios con variaciones extremas de temparatura. Si la unidad es llevada bruscamente de un sitio frío a otro cálido, la humedad puede condensarse en la unidad y en la cinta.

6 PARA EVITAR LESIONES PERSONALES

• No coloque equipos no fijados en superficies inclinadas.

• No coloque esta unidad sobre ningún soporte que no esté firme, nivelado y que sea adecuadamente fuerte. La unidad podría caerse y producir graves lesiones a niños o adultos y dañarse la unidad misma.

• La combinación de aparato y carrito debe moverse con cuidado. Las paradas súbitas, una fuerza excesiva ya las superficies irregulares pueden ocasionar el vuelco de la combinación de aparato y carrito.

• Siga atentamente las instrucciones de funcionamiento y utilice los accesorios recomendados por el fabricante al hacer funcionar esta unidad o al conectaria a otros equipos.

62

INSTALACIÓN DE LA ANTENA EXTERIOR

1 CONEXIÓN SEGURA DE LA ANTENA Y DE LOS CABLES

Si se conectara una antena exterior o sistema de cable conectado al equido, el usuario deberá asegurarse de que la antena o el sistema de cable disponen de toma a tierra

CÓDIGOO ELÉCTRICO

NEC-NATIONAL

BAJADA DE ANTENA

como forma de proporcinar protección contra la acumulación de cargas estábicas y saltos de corrientes. La sección 810 del Código

Eléctrico Nacional, ANSI/NFPA 70 (en

DE CONEXIÓN

A TIERRA

UNIDAD DE DESCARGA

DELA ANTENA (SECCIÓN

S10-20 DEL NEC)

EQUIPO DE

SERVICIO

ELÉCTRICO

Canadá, la parte 1 del Código Eléctrico

Canadiense) proporciona información con respecto a la

CONDUCTORES CONEXIÓN

A TIERRA (SECCIÓN

S10-20 DEL NEC)

EMPALMADOR DE

CONEXIÓN A TIERRA

SISTEMA DE ELECTRODOS DE

CONEXIÓN A TIERRA DEL SERVICIO

ELÉCTRICO (ART, 250 DEL NEC, PARTE H)

conexión a tierra correcta del mástil y la estructura de soporte, conexión a tierra de los cables de bajada de antena a una unidad de descarga, tamaño de los conductores a tierra, ubicación de la unidad de descarga de antena, conexión de los electrodos a tierra y requisitos del electrodo de toma a tierra.

2 MANTENGA LA ANTENA LIBRE DE LÍNEAS O CIRCUITOS DE ALTO VOLTAJE

Un sistema de antena exterior deberá ser colocado bien alejado de líneas de alimentación, luz eléctrica o circuitos de alimentación para que nunca esté en contacto con tales fuentes de alimentación si se cayera. Al instalar una antena exterior, debe tenerse muchísimo cuidado para evitar las líneas de alimentación, circuitos u otras fuentes de alimentación ya que esto podría resultar mortal.

Debido a los riesgos implicados en la instalación de una antena, tal operación debe dejarse a un profesional.

UTILIZACIÓN DE LA UNIDAD DE VÍDEO

Si la unidad ha estado almacenada o es trasladada a una nueva ubicación, remítase primero a la sección de INSTALACIÓN de estas medidas de seguridad.

1 MANTENGA ESTA UNIDAD DE VÍDEO ALEJADA DEL AGUA O DE

HUMEDAD DE CUALQUIER TIPO

2 SI EL EQUIPO ES EXPUESTO A LA LLUVIA, HUMEDAD, O FUERTES

IMPACTOS, desenchufe la unidad y que sea revisada por un técnico cualificado antes de volver a utilizarla.

3 DURANTE UNA TORMENTA ELÉCTRICA

Durante una tormenta con rayos, tanto en interiores como en el exterior, o antes de dejar la unidad sin utilizar durante largos períodos de tiempo, desconecte todos los equipos de la fuente de alimentación así como la antena y el sistema de cableado.

4 AL ENCHUFAR LA UNIDAD

•No exponga nunca la unidad a la lluvia o el agua. NO LA HAGA FUNCIONAR si se ha derramado líquido dentro de la unidad. Desenchufe la unida inmediatamente ya que sea revisada por un técnico. Pueden producirse incendios o sacudidas eléctricas derivadas de cortocircuitos eléctricos causados por el contacto de líquidos con el interior de la unidad.

•No deje caer ni introduzca ningún objeto por las aberturas de la unidad. Algunas piezas internas tienen un voltaje peligroso y el contacto con ellas puede producir sacudidas eléctricas o incendios.

•Evite colocar la unidad directamente encima o debajo del televisor, ya que esto prodría causar interferencias eléctricas. Mantenga cualquier tipo de imán alejados de equipos electrónicos.

5 UTILIZACIÓN DE ACCESORIOS

Utilice sólo accesorios recomendados por el fabricante para así evitar riesgos de incendio, sacudidas eléctricas y otros peligros.

6 LIMPIEZA DE LA UNIDAD

Desenchufe la unidad. Luego utilice un paño limpio y seco, sin tratamiento químico para quitar suavemente el polvo o suciedad. NO UTILICE productos de limpieza, aerosoles, o aire comprimido que pudieran causar un exceso de pulverización o introducirse en la unidad y ocasionar sacudidas eléctricas.

Caulquier substancia, como cera, cinta adhesiva, etc., podría arruinar el acabado de la superficie. La exposición a substancias grasosas, áreas húmedas o polvorientas puede afectar de manera adversa a las piezas intemas.

SERVICIO

1 EL USUARIO NO DEBE REALIZAR NINGUNA OPERACIÓN DE

SERVICIO TÉCNICO POR SÍ MISMO

Si, después de observar atentamente las detalladas instrucciones de funcionamiento, este producto de vídeo no funcionara correctamente, no intente abrir o extraer las tapas, o realizar cualquier ajuste no indicado en este manual.

Desenchufe la unidad y llévela a un técnico cualificado de servicio técnico.

2 SI FUERAN NECESARIAS PIEZAS DE RECAMBIO

Asegúrese de que el técnico de servicio utiliza sólo piezas especificadas por el fabricante, o de las mismas características que las piezas originales.

La utilización de subsitutos no autorizados puede ser causa de incendios, sacudidas eléctricas, u otros peligros.

3 QUE EL TÉCNICO DE SERVICIO TÉCNICO REALICE UNA

COMPROBACIÓN DE SEGURIDAD

Después de cualquier servicio o reparación de la unidad, solicite al técnico de servicio que realice una completa comprobación de seguridad tal como se describe en la literatura de servicio técnico del fabricante para asegurarse así que la unidad de vídeo se encuentra en condiciones de funcionamiento seguras.

D4754S P36-72 (040202).p65

62 2004/02/02, 13:23

PRECAUCIONES DE SEGURIDAD

PARA PREVENIR INCENDIOS O CHOQUES ELÉCTRICOS NO

EXPONGA ESTE APARATO A LA LLUVIA O LA HUMEDAD.

PARA PREVENIR CHOQUES ELÉCTRICOS, ASEGURASE QUE LA

CLAVIJA HAGA JUEGO CON EL ENCHUFE Y CONÉCTELO

COMPLETAMENTE.

PRECAUCION

PELIGRO DE DESCARGA

ELECTRICA NO ABRIR

PRECAUCION: PARA EVITAR LA POSIBILIDAD DE

UNA DESCARGA ELECTRICA NO DESMONTAR LA

CUBIERTA (O LA PARTE TRASERA). ESTE APARATO

NO PUEDE SER REPARADO POR EL PROPIETARIO.

PARA CUALQUIER TRABAJO DE SERVICIO SE

DEBE RECURRIR A UN TECNICO ESPECIALIZADO.

Este símbolo advierte al usuario de que hay voltaje sin aislamiento dentro de la unidad de suficiente magnitud como para ocasionar sacudidas eléctricas. Por lo tanto, resultará peligroso realizar cualquier tipo de contacto con toda pieza interna de la unidad.

Este símbolo alerta al usuario de que se ha incluido importante literatura sobre el funcionamiento y mantenimiento de esta unidad. Por tanto, debe leerse atentamente tal literatura a fin de evitar cualquier problema.

Advertencia FCC:

Cualquier cambio o modificación no autorizado de este equipo anulará la autorización al usuario para hacer funcionar la unidad.

FCC Warning:

Any unauthorized changes or modifications to this equipment would void the user’s authority to operate.

D4754S P36-72 (040202).p65

63 2004/02/02, 13:23

63

Spanish Quick Use Guide/ Guía para rápida consulta

Realice la conexión de la antena o TV por cable antes de enchufar el cable de CA.

El DVD/VCR iniciará automáticamente la fijación de los canales y del reloj al enchufar el cable de CA.

CONEXIONES

Para Ant/Cable

➛

1

Conecte el cable de la antena al terminal IN

FROM ANT del DVD/VCR.

Televisor

DVD/VCR

2

Conecte el terminal OUT TO TV del DVD/VCR a la entrada de la antena VHF/UHF del TV con el cable RF incluido.

Para Sistema Digital de Satelite (DSS)/ Convertidor de cable

➛

1

Conecte la salida de convertidor de cable al terminal IN FROM ANT.

Televisor

VHF/UHF

➛

DVD/VCR

2

2

Conecte el terminal OUT TO TV del DVD/VCR a la entrada de la antena VHF/UHF del TV con el cable RF incluido.

2

Terminal

OUT TO TV

Terminal

IN FROM ANT.

Terminal

OUT TO TV

Terminal IN FROM ANT.

1

Entrada (IN) desde

ANT./CABLE

Estuche convertidor de TV por cable

1

Entrada (IN) desde

ANT./CABLE

CONFIGURACION INICIAL

VHF/UHF

1

2

Encienda el TV y cambie al canal 3.

Enchufe el cable de CA.

El DVD/VCR se encenderá e iniciará las fijaciones de los canales y del reloj.

• Si no aparece la pantalla de abajo, compruebe la conexión del DVD/VCR-TV y si el canal del

TV está a 3, intennte cambiando al canal 4.

• Para cambiar el canal de salida del DVD/VCR, consulte las instrucciones de “Canal de salida del VCR” (informaciones en inglés página 19).

Enchufe el cable de CA.

3

Al usar cables coaxiales RF del tipo “tuerca”, apriételos solamente con los dedos. Un apriete excesivo puede dañar los terminales.

Las fijaciones se realizan automáticamente.

Cuando termina las fijaciones, aparecerá la siguiente pantalla.


CANCEL : STOP

AUTO CLOCK SET

PROCEEDING

Al inicio, el idioma de la pantalla está fijado a inglés.

Para cambiar el idioma, seleccione la pantalla

MENU (informaciones en inglés página 18).

Si aparece en la pantalla “AUTO CLOCK SET IS

INCOMPLETE (FIJACION AUTOMATICA DEL

RELOJ ES INCOMPLETO)”, Ajuste el reloj como se describe a continuación.

AUTO CLOCK SET

IS I NCOMPLETE

CANCEL : STOP

Si está usanndo un convertidor de TV por cable y en su area hay un canal de Public Broadcast

Station (PBS), ajuste su convertidor al canal PBS de su area. Si está usando un receptor DSS, este debe estar apagado.

Nota

• Los botones de funciones no funcionan durante la configuración inicial.

• Para retirar un cassette durante el ajuste automático, presione EJECT en el control remoto o STOP dos veces en el aparato. En este caso, los ajustes de los canales y la hora se deben hacer manualmente. Para los ajustes seleccione la pantalla MENU (informaciones en inglés página 18).

• Dependiendo de las condiciones, el ajuste automático puede durar más de 30 minutos.

En ese caso, presione STOP para detener el ajuste automático y realice los ajustes manualmente en la pantalla MENU.

Si la fijación ha sido incompleta.

1 Presione la tecla ACTION en el control remoto para visualizar la pantalla del menú SET

CLOCK.

SET CLOCK

1 / 1/2004 THU --

-

DST : ON

- - - - - - - - -- - - - - - - -- - - - - -

2

PLEASE SET CLOCK BY

PRESSING ACT I ON KEY

AJUSTE MANUAL DEL RELOJ

Presione para seleccionar el mes y SET para ajustar. De la misma forma, seleccione y ajuste la fecha, año, hora y DST (hora de verano).

SET CLOCK

6 /20/2004 SUN -

-

15:30PM

DST : ON

- - - - - - - - -- - - - - - - -- - - - - -

3 Presione dos veces la tecla ACTION para poner el RELOJ en marcha y salir.

64

D4754S P36-72 (040202).p65

64 2004/02/02, 13:23

Operaciones básicas para la reproducción

1

2

Inserte un cassette,

• La alimentación del DECK se activa. Si Auto

VCR/TV (consulte la página 32) está en

“INACT (OFF)”, presione VCR/TV en el control remoto para el modo VCR.

Presione PLAY para reproducir el cassette.

• Si el cassette no tiene la lengüeta de prevención de grabación (página 6), se inicia la reproducción automáticamente.

Detalles especiales durante la grabación

Presione FF/SLOW+ o REW/SLOW- para búsqueda de escenas hacia delante/ hacia atrás. Presione PLAY para liberar.

Durante la búsqueda, cada vez que

presione FF o REW se cambia la velocidad:

Presione PAUSE/STILL para imagen Fija

(Congelada).

Presione PLAY para liberar.

Presione PAUSE/STILL en el modo de imagen fija para imágenes cuadro a cuadro.

Presione PLAY para liberar.

Presione FF/SLOW+ o REW/SLOW- en el modo de imagen fija para cambiar la velocidad de las imágenes a cámara lenta.

3

Presione STOP para detener el cassette.

Rebobinado/Avance rápido

Presione REW/SLOW- o FF/SLOW+ en el modo de parada para rebobinado/avance rápido del cassette.

• Rebobina una cinta T-120 en aproximadamente 1 minuto.

Presione EJECT en el control remoto, o STOP/EJECT en el DECK para expulsar el cassette.

Programación fácil para la grabación con temporizador

1

Presione PROG

para visualizar la pantalla de Programacion.

2

P FE I N I C PARADA CA VEL

1 -- --:-- --:-- -- --

2 -- --:-- --:-- -- --

3 -- --:-- --:-- -- --

4 -- --:-- --:-- -- --

ELEG I R : FIJAR : SET

TERM I NAR : PROG

1) Presion .

2) Para ajustar la FECHA de grabación, presione

para seleccionar:

1-31 = una vez, o

DIARIO = a la misma hora de lunes a viernes, o

SEMANA = a la misma hora cada semana.

Orden para elegir

Ejemplo

Fecha de hoy 7

8 9

31

1

2

/ Orden para elegir

6

DIARIO

SEMANAL

(SA)

SEMANAL

(LU)

SEMANAL

(DO)

3) Ajustes los ítems restantes,

presione SET para ajustar los tiempos de

INICIO/PARADA, CANAL o entrada de LINEA

(página 35), y la velocidad de la cinta (SP, SLP).

Luego presione para seleccionar.

Presione PROG para finalizar PROGRAM.

Operaciones básicas para la grabación

1 Inserte el cassette con lengüeta de

protección de grabación (página 6).

• La alimentación del DECK se activa. Si Auto

VCR/TV (consulte la página 32) está en

“INACT (OFF)”, presione VCR/TV en el control remoto para el modo VCR.

2

3

4

Presione CH

/

, o las teclas de números para seleccionar el canal.

Presione SPEED para seleccionar la velocidad de grabación (página 6)

• SP = Reproducción normal

• SLP = Reproducción extra larga

Presione REC para comenzar a grabar.

• Para eliminar escenas indeseadas, presione

PAUSE/STILL para hacer una pausa, y al presionar nuevamente continua la grabación.

• No podrá ver otro canal durante la grabación.

5

Presione STOP para detener la grabación.

3

P FE I N I C PARADA CA VEL

1 13 2:00p 3:20p 02 SLP

2 -- --:-- --:-- -- --

3 -- --:-- --:-- -- --

4 -- --:-- --:-- -- --

FIJACION ES COMPLETO

CANCELAR : ADD/DLT

ELEG I R : FIJAR : SET

TERM I NAR : PROG

Presione

para seleccionar un número que no está usando para ingresar mas programas y

presione SET para ajustar.

Luego repita el paso 2.

O

Presione nuevamente

PROG para salir.

Grabación de un toque

Presione REC repetidamente para ajustar la hora de grabación (30 min - 4 horas).

• La videograbadora termina la grabación a una hora programada.

Grabación normal

0:30 1:00

4:00 3:00 2:00 1:30

65

D4754S P36-72 (040202).p65

65 2004/02/02, 13:23


2

3

Operaciones básicas del DVD

Funcionnamiento del DVD utilizando visualizaciones en pantalla

1 Presione

POWER en el control remoto o el aparato.

Presione

DVD para seleccionar el modo DVD.

1) Presione OPEN/CLOSE.

2) Ponga un disco en la bandeja de disco.

• Sujete el disco sin tocar ninguna de sus superficies, póngalo con el lado donde esté impreso el título hacia arriba, alinéelo con las guías y póngalo en su posición apropiada.

Disco de 3” (8 cm) / Disco de 5” (12 cm)

Cuando se presiona DISPLAY, la visualización en pantalla muestra la información del disco (título / capítulo / número de lista, tiempo transcurrido de reproducción, audio / idioma del subtítulo, y ángulo) e información (repetir la reproducción, modo reproducción, Karaoke vocal encendido / apagado, etc.).

1

Presione

DISPLAY en el modo reproducción o parada para visualizar las visualizaciones en pantalla.

• Cada vez que se presione DISPLAY, la visualización en pantalla cambia como se muestra a continuación.

4 Presione

PLAY para iniciar la reproducción.

La bandeja del disco se cierra automáticamente.

• Si está usando un DVD interactivo y aparece el menú de títulos (TITLE MENU), siga al paso 5.

Información seleccionada del disco

5 Presione

o las teclas numéricas para seleccionar el artículo deseado.

Presione

SET o PLAY para la reproducción.

Si usa las teclas numéricas, la reproducción comienza automáticamente.

Información seleccionada del DECK

Pantalla normal

6

7

Presione

STOP para parar la reproducción.

2

Presione

(o ) para seleccionar el ítem deseado.

Presione

SET para ajustar.

Presione

OPEN/CLOSE para expulsar el disco.

3

■ Para buscar una escena particular

Búsqueda hacia adelante

Presione

FF/SLOW+ en el modo de reproducción.

Búsqueda hacia atrás

Presione

REW/SLOW- en el modo de reproducción.

(Para liberar, presione PLAY)

■ Para saltar un capítulo o una pista

Salto hacia adelante

Presione SKIP

l en el modo de reproducción.

Salto hacia atrás

Presione l

SKIP en el modo de reproducción.

■ Para ver una imagen fija

Presione

PAUSE/STILL durante la reproducción.

(Para liberar, presione

PLAY)

■ Para ver imágenes cuadro a cuadro (DVD)

Presione

PAUSE/STILL en el modo de imagen fija.

La imagen avanza un cuadro cada vez que presiona la tecla. (Para volver a la reproducción normal, presione

PLAY)

■ Para ver en cámara lenta (DVD)

Presione

FF/SLOW+ o REW/SLOW- en el modo de imagen fija.

(Para liberar, presione

PLAY)

Presione

para seleccionar el ajuste deseado.

Presione

SET para ajustar.

Para volver a la pantalla normal,

Presione repetidamente CLEAR o DISPLAY.

<Ejemplo (Vídeo DVD)>

T I TULO : 12

CAP I TULO : 11

DVD

00 : 12 : 34

ELEG I R :

F I JAR : SET S I GU I ENTE: D I SPLAY

<Ejemplo (DVD-RAM)>

T I TULO : 12

CAP I TULO : 11

DVD

00 : 12 : 34

ELEG I R :


<Ejemplo (Audio DVD)>

GRUPO : 1

P I STA : 1

DVD-AUDIO

00 : 12 : 34

T I TULO : 12

CAP I TULO : 24

DVD

00 : 12 : 34

ELEG I R : 0 - 9


T I TULO : 12

CAP I TULO : 24

DVD

00 : 12 : 34

ELEG I R :


GRUPO : 1

P I STA : 1

DVD-AUDIO

00 : 12 : 34

ELEG I R :

F I JAR : SET T E R M I N A R : D I SPLAY

ENTRAR: 0 - 9

F I JAR : SET T E R M I N A R : D I SPLAY

66

D4754S P36-72 (040202).p65

66 2004/02/02, 13:23

1

2

3

4

Fijaciones iniciales

Presione

para seleccionar el artículo deseado.

Presione

SET.

5

Volver a visualizar el menú de DVD para continuar el ajuste.

Presione

ACTION y pase al paso 3 para ajustar otro ajuste o, para salir, presione ACTION dos veces.

Selección de IDIOMAS DEL

DISCO [DVD solamente]

Presione DVD para seleccionar el modo DVD.

Presione ACTION en el modo de parada para visualizar MENU.

Presione

para seleccionar el artículo deseado.

Presione

SET.

IDIOMAS DEL DISCO

Todos los idiomas ofrecidos en el disco pueden ser ajustados. Si el idioma ajustado no es ofrecido en el disco, se seleccionará el idioma original del disco.

SALIDA DE AUDIO

Puede usted ajustar la salida audio procedente del terminal de salida audio digital.

DETENER RASTREO

Para seleccionar “CAMPO”, “CUADRO” o “AUTO” para prevenir inestabilidad o para permitir ver textos pequeños o patrones finos claramente en el modo de imagen fija.

TV PREFERENCIA

Para seleccionar cuando el material del vídeo es para pantalla ancha y se quiere reproducir en el estilo Pan&Scan, en el estilo Letterbox o en el estilo

16:9 en la pantalla.

Seleccione “AUDIO”

(Fijación de fábrica : inglés)

Inglés / Español / Francés / Japonés :

Original :

Se seleccionará el idioma original de cada disco.

OTRO 0000 :

Se puede seleccionar el otro idioma.

Seleccione “SUBTITULO”

AUTO : Se seleccionará el mismo que fue seleccionado en la preparación de

“AUDIO”. (Fijación de fábrica)

• Si el idioma seleccionado en la preparación de “AUDIO” se utiliza durante la reproducción, los subtítulos no aparecerán.

• Si se utiliza otro idioma durante la reproducción, los subtítulos aparecerán en el idioma seleccionado en la preparación de “AUDIO”


OTRO 0000 :

Se puede seleccionar el otro idioma.

Seleccione “MENU”

(Fijación de fábrica : inglés)


OTRO 0000

: Se puede seleccionar el otro idioma.

Cambio del idioma de subtítulos

[Vídeo DVD solamente]

EI idioma de los subtítulos seleccionado al hacer las fijaciones iniciales se puede cambiar por otro idioma diferente, si éste se encuentra disponible.

1

ELEG I R : SUB TITLE

Presione

SUBTITLE durante la reproducción.

Cuando no haya subtítulos grabados, se visualizará “-” en lugar del número de idioma.

2

ELEG I R : SUB TITLE

Presione

SUB TITLE, las teclas numéricas para seleccionar el idioma deseado.

o

Visión desde otro ángulo

[DVD solamente]

Algunos discos DVD tienen escenas que han sido filmadas simultáneamente desde

ángulos diferentes.

Con estos discos, la misma escena podrá verse desde cada uno de estos ángulos diferentes utilizando el botón ANGLE.

1

ANGULO : 1

ELEG I R : ANGLE

Presione ANGLE

durante la reproducción para visualizar la selección del ángulo.

2

ANGULO : 2

Presione ANGLE

repetidamente o para seleccionar el

ángulo deseado.

ELEG I R : ANGLE

67

D4754S P36-72 (040202).p65

67 2004/02/02, 13:23


1 Presione

AUDIO durante la reproducción para visualizar la pantalla AUDIO.

2

Selección de vocal para los discos de Karaoke [DVD solamente]

Presione para

seleccionar VOZ y presione AUDIO o para seleccionar tal como se indica a continuación.

Cambio del idioma de la pista de sonido [DVD solamente]

EI idioma de la pista de sonido seleccionado al hacer las fijaciones iniciales se puede cambiar por otro idioma diferente, si éste se encuentra disponible.

1 Presione

AUDIO durante la reproducción para visualizar

SONIDO en la pantalla.

ELEG I R : AUD I O /

ELEG I R : AUDIO

• DVD Karaoke (1 vocal) VOZ ACTIVO VOZ INACTIVO

• DVD Karaoke (2 vocals) VOZ V1 VOZ V2 VOZ V1+V2 VOZ INACTIVO

2 Presione

AUDIO, teclas numéricas para seleccionar el idioma deseado.

o las

ELEG I R : AUDIO

Utilización de un menú de títulos

[DVD solamente]

Algunos discos con películas, vienen con dos o más títulos. Por ejemplo, si el disco tiene un menú de títulos grabados, el botón TITLE podrá utilizarse para seleccionar el título de la película.

1

Presione TITLE durante la reproducción.

Ahora se visualiza una lista de los títulos del disco.

Utilización de un menú de DVD

[DVD solamente]

Algunos discos DVD ofrecen un menú especial.

Este menú incluye guías para contenidos únicos, audio, subtitulos, idiomas, etc.

Aunque los contenidos y las operaciones se cambian, los siguientes son unos pasos básicos para el uso del menú.

1 Presione

MENU durante la reproducción.

El menú de DVD introducido en el disco se visualiza ahora.

2

T I TLE MENU

Dogs Cas t l es

Love r s B i r ds

Dogs of the world

Presione

o las

teclas de números para seleccionar el título deseado.

Presione

SET o PLAY para elegir.

2

DVD MENU

1 . SUBT I TLE

2 . AUD I O

3 . ANGLE

<ejemplo>

Presione

o las

teclas de números

para seleccionar el ítem deseado.

Presione

SET o PLAY para elegir.

<ejemplo>

Ampliación de la imagen [DVD solamente]

Durante la reproducción de un DVD, puede ampliar partes específicas de una imagen y seleccionar la relación de zoom usando el botón ZOOM.

Presione

ZOOM repetidamente para cambiar el tamaño de la imagen como se indica a continuación:

■ Use los botones , , y para desplazar la posición hacia arriba, hacia abajo, hacia la izquierda o hacia la derecha.

2da

3da

68

D4754S P36-72 (040202).p65

68 2004/02/02, 13:23

Puede utilizar esta unidad para reproducir audio de formato MP3/WMA/JPEG, grabado para uso personal con una computadora, etc., en un

CD-ROM o CD-RW. La ejecución no podrá realizarse en algunos casos, debido a las condiciones de la grabación.

1

2

3

Funcionamiento de la ejecución de MP3/WMA/JPEG

Presione

POWER en el control remoto o DECK.

Presione

OPEN/CLOSE y a continuacion coloque un disco MP3/WMA/JPEG en la bandeja de discos.

Presione

OPEN/CLOSE para cerrarla.

Se visualizará el MENU MP3/WMA/JPEG y la ejecución se iniciará automáticamente.

(Se visualizará el directorio del CD.)

Estado de la función

<ejemplo>

REPROD

Carpeta principal

Area de las carpetas

(La carpeta visualizada actualmente se volverá verde)

ROOT . .

VA END_WALTZ

TECHNO DD_CUB I C

POPS NOCTURNE

JAZZ NORN

MODE DE REPRODUCCION :

NORMAL

MODO DE REPRODUCCIÓN

Area de archivos

(El archivo/ la carpeta se visualiza con un cursor.)

: Archivo MP3

:Carpeta

: Archivo WMA

:Carpeta principal

: Archivo JPEG

4

■

Ejecución MP3/WMA/JPEG (Durante el modo STOP)

Presione

para seleccionar un archivo

MP3/WMA ( / ) o un archivo JPEG ( ), y

presione

SET o PLAY.

• MP3/WMA

Búsqueda hacia adelante/hacia atrás

➡

Presione

FF/SLOW+ o REW/SLOW- durante la ejecución.

Salto de pista hacia adelante/hacia atrás

➡

Presione

SKIP+ | o

SKIP- |

durante la ejecución.

• JPEG

Búsqueda siguiente/anterior

➡

Presione

SKIP+ | o

SKIP- |

.

Inicie la muestra-diapositiva

➡

Presione

FF/SLOW+ o REW/SLOW-.

Ampliar una imagen

➡

Presione

ZOOM.

Girar una imagen

➡

Presione

ANGLE.

Presione

STOP para detener la operación descrita arriba.

■

Seleccione MODO DE REPRODUCCION

(Durante el modo STOP)

Presione

para seleccionar el MODO

DE REPRODUCCIÓN deseado.

[MODO DE REPRODUCCIÓN]

NORMAL:

Todos los archivos se reproducen sólo una vez.

REPETICION DE UNA MUSIC:

El archivo seleccionado se reproduce repetidamente.

REPETICION DE UN ARCHIVO:

Los archivos que se encuentran en la carpeta seleccionada se reproducen repetidamente.

REPETICION DEL DISCO:

Todos los archivos se reproducen repetidamente.

5

Presione

ACTION para regresar al

DVD MENU PRINCIPAL.

D4754S P36-72 (040202).p65

69 2004/02/02, 13:23

69

Index

DECK & VCR

A ACTION button ................................. 8, 18

Accessories ............................................ 4

ADD/DELETE button

(Add or Delete a Channel) ............ 8, 19

Audio Broadcast types

(Stereo/SAP/Mono) ............................ 26

Audio Mode (Playback, Recording) .... 27

Auto Operation Functions .................... 31

Auto Shut-Off ........................................ 33

B Batteries ................................................. 4

Blue Light (ON/OFF Feature) ........... 9, 32

C Channel (“SET UP CHANNEL”) .......... 18

Channel Up/Down,

Tracking/V-Lock Button .................... 4, 8

Clock (“SET CLOCK”) .......................... 18

CM/ZERO SEARCH button ............. 8, 30

Commercial Skip ................................. 30

Connections ................................. 12 ~ 15

Copy Your Tapes (Dubbing) ............... 35

COUNTER RESET button ............... 8, 30

Customer Services Directory ............... 61

D DISPLAY button ............................... 8, 11

DST (Daylight Saving Time) ................ 19

E EJECT button ................................... 8, 20

ENTER button

(For tuning TV Channel) ................ 8, 28

F FAST FORWARD/SLOW+ button ..... 8, 20

H Head Cleaning ...................................... 4

I Index Search ........................................ 30

Indicator (Multi Function Display) ....... 11

Initial Setup (Ready to Play) ......... 16, 17

INPUT button ................................... 8, 35

L Limited Warranty ........................... 60, 61

Location of Controls

(Remote, DECK) .......................... 8 ~ 10

M Multi-Brand Control ....................... 28, 29

Multi Function Display (Front Display)

ON/OFF Feature ................................... 34

O On-Screen Displays (VCR) ................. 11

One Touch Recording ......................... 21

P PLAY button (Playback a Tape) ...... 8, 20

POWER button ....................................... 8

PROG button (PROGRAM) .............. 8, 24

Program Clear, Review, Replace ....... 25

Q Quality Picture ....................................... 4

R REC button (Record on a Tape) ..... 8, 21

Record Tab ............................................ 6

Remote Sensor ...................................... 9

Remote Warning .................................. 34

Repeat Play ......................................... 31

Reset All Memory Functions ................. 9

REWIND/SLOW- button ................... 8, 20

S SAP/Hi-Fi ............................................. 27

SEARCH button ............................... 8, 30

Spanish Quick Use Guide ........... 62 ~ 69

Specifications ......................................... 7

SPEED button .................................. 8, 21

Still (Freeze) Picture ............................ 20

STILL/PAUSE button (Still Picture) .. 8, 20

STOP button ..................................... 8, 20

T Tape Position, Tape Status ................. 31

Tape Select .......................................... 31

Timer Recording .................................. 24

Trouble Shooting ........................... 58, 59

TV mode button ................................ 8, 28

V VCR Lock ............................................. 32

VCR mode button ............................ 8, 28

VCR/TV button ................................. 8, 21

VCR/TV Selection Feature .................. 32

VOLUME +/- button (TV Volume) .... 8, 28

WWarning and Instruction Displays ....... 57

Weak Signal Display ........................... 33

70


D4754S P36-72 (040202).p65

70 2004/02/02, 13:23

DVD

A ACTION button ................................. 8, 52

ANGLE button

(Multiple Angle Viewing) ......... 8, 37, 51

AUDIO button

(Audio Soundtrack Language) ...... 8, 36

Audio Output

(For Selecting Audio Output) ............. 53

Auto-Power Off Function ..................... 23

A/V OPTIMIZER .................................... 55

B Bonus Group (For DVD-Audio) ........... 41

C CLEAR button .................................. 8, 39

Component Video Output .............. 10, 13

D Direct Navigator ................................... 42

Disc Languages ................................... 52

DISPLAY button

(“On-Screen Display”) .................... 8, 44

DTS ...................................................... 14

DVD-Audio ........................................... 41

DVD Menu ........................................... 38

DVD mode button ............................ 8, 28

DVD-RAM (DVD-VR) ........................... 42

F Frame by Frame Picture ...................... 23

Forward/Reverse Chapter/Track Skip ... 23

Forward/Reverse Scene Search .......... 23

J JPEG ............................................ 49 ~ 51

K Karaoke

(Vocal Selection for Karaoke Discs) ... 37

L Language Code List ............................ 56

M MENU button

(To display DVD Menu) ................. 8, 38

MP3 ...................................................... 49

Multiple Angle Viewing ........................ 37

O OPEN/CLOSE button ....................... 8, 22

Optical Digital Audio Output .......... 10, 15

P PAGE button (Still Image Skip) ....... 8, 41

PLAY button (Play a Disc) ............... 8, 22

Play List ................................................ 43

Program Play (For CD) ........................ 39

Progressive Scan ..................... 10, 13, 55

R Random Play (For CD) ........................ 40

Repeat Play ................................... 47, 48

Resume Function ................................. 23

RETURN button ............................... 8, 22

Rotation ................................................ 51

S SKIP+ l or SKIP- l button

(Forward/Reverse Chapter/Track) 8, 23

Slide-show ........................................... 50

SLOW+/SLOW- button

(Slow Motion Picture) .................... 8, 23

STILL/PAUSE button

(Still Picture or Pause) ................... 8, 23

Still Mode

(For selecting “FIELD” or “FRAME”) .. 54

STOP button ..................................... 8, 22

SUB TITLE button

(For selecting Subtitle Language) ... 8, 36

S-Video Out .................................... 10, 13

T TITLE button (Title Menu) ................ 8, 38

TV Mode

(For selecting the screen display style) .. 54

V VOLUME ADJUST button ................ 8, 40

V.S.S. (Virtual Surround Sound) ..... 8, 23

WWMA ..................................................... 49

Z ZOOM button (Picture Zoom) ..... 8, 37, 51

71

D4754S P36-72 (040202).p65

71 2004/02/02, 13:23

Panasonic Consumer Electronics Company,

Division of Matsushita Electric Corporation of America

One Panasonic Way Secaucus, New Jersey 07094

Panasonic Sales Company (“PSC”),

Division of Matsushita Electric of Puerto Rico, Inc.

Ave. 65 de Infantería. Km. 9.5 San Gabriel Industrial Park, Carolina,

Puerto Rico 00985

D4754S P36-72 (040202).p65

72 2004/02/02, 13:23

P

Printed in Indonesia

LSQT0797 A

S0104-1024

Panasonic PV-D4754S DVD-VCR Combo User manual

Assistant Bot

Operating Instructions

Connections and Initial Setup Procedures are on pages 12 to 17.

MULTI FORMAT PLAYBACK

Important Safeguards and Precautions

Safety Precautions/Mesures de sécurité

To prevent fire or shock hazard, do not expose this equipment to rain or moisture.

To prevent electric shock, match wide blade of plug to wide slot, fully insert.

Afin de prévenir tout risque d’incendie ou de chocs électriques, ne pas exposer cet appareil à la pluie ou à une humidité excessive.

Pour éviter les chocs électriques, introduire la lame la plus large de la fiche dans la borne correspondante de la prise et pousser jusqu’au fond.

CAUTION:

FCC NOTE:

FCC Caution:

Region Management Information:

1

2

4

Before Using

Head Cleaning

Video Head Clog Sensor

Accessories

Cleaning DECK

Loading the Batteries

Features for a Quality Picture (VCR)

Record/ Playback Time

Table of Contents

Initial Setup (Connection)

Basic Operation

VCR Operation

DVD Operation

For Your Information

DECK & Cassette Information

Prevent Accidental Tape Erasure

DVD-RAM discs

Disc formats supported by this DECK

Disc Handling

Specifications

Definition of Terms (DVD)

Location of Controls

Remote Control

Reset All Memory Functions

Location of Controls (continued)

Rear View of DECK

VCR

To enjoy PROGRESSIVE SCAN video

Displays (On Screen & Multi Function)

On Screen Displays (VCR)

Multi Function Display

Connections

Basic Connections

VIDEO

AUDIO

Other Connections

Connect With Two Cable Boxes

You Can

You Cannot

You Can

You Cannot

Connections For DVD Only (enjoying higher picture quality)

DVD OUTPUT

or

Connections (continued)

Audio Connections

Ready Checklist

Enjoying digital audio output from the digital audio output connector

DECK Dolby Digital Decoder Amplifier Speaker

or

DECK DTS (Digital Theater Systems) Decoder Amplifier Speaker

Initial Setup for Basic Connections (Ready to Play)

Before doing Initial Setup

Turn TV on.

Initial Setup (Ready to Play)

Plug VCR Power plug into an AC wall outlet.

Continued on next page...

dy to Play)

Manual Clock Set

Reset Language, Channels, Clock, VCR’s O

Language

Channels