Alpine V-Power MRP-M200 Mono Amplifier Datasheet

MRP-M200

1 Channel V-Power Series Mono Amplifier

F E AT U R E S

General

Bass Engine®

1 Channel Operation

MOSFET Power Supply

No Current Limiting

Darlington Bi-Polar Outputs

STAR Circuitry

Solid Copper Bus Bars

MultiMode

Top Mounted LED Power Indicator

Adjustable Crossover (LP)

Bass EQ

Subsonic Filter

Continuously Adjustable Gain Control

Both sides Terminal Layout

Gold Plated RCA Input Connectors

Speaker Level Inputs

Gold Plated Power Screw Terminals

Gold Plated Speaker Screw Terminals

Noise Elimination Coil

0¡ 180¡

PHASE

75

100

140

55 170

50 200

(Hz)

LP FILTER bass engine

+6db NOM

0.5V

0db

OFF ON

BASS EQ

+12db MIN

GAIN

MAX

CH—2 CH—1

(L)

INPUT

(R)

(R) (L)

SPEAKER

LEVEL INPUT

S P E C I F I C AT I O N S

MAX Power (at 14.4V,EIAJ)

Per channel into 2 ohms ..........................................................................300W x 1

RMS Power (at 14.4V,20Hz-20kHz)

Per channel into 4 ohms........................................................150W x 1 (0.08% THD)

Into 2 ohms .................................................................................200W x 1 (0.3%)

Bass Engine®

Bass EQ (Variable) ........................................................... 50Hz Variable (0 - +12dB)

Crossover Network ............................................Variable 50Hz - 200Hz LP (18dB/oct)

General

Frequency Reponse ................................................................20Hz-200Hz (+0,-3dB)

Signal to Noise (S/N) ..........................................100dBA (referenced to rated power)

Input Sensitivity (for rated power) .........................................................200mV ~ 4.0V

Slew Factor.......................................................................................greater than 5

Input Impedance .......................................................................................10k ohm

Speaker Impedance .............................................4 or 2 ohms(stereo), 4 ohms(bridged)

Power Requirements ..............................................................14.4V DC (11V to 16V)

Heat Sink (WxHxD)...........................................................230mm x 58mm x 230mm

Foot Sink (WxHxD) ...........................................................250mm x 58mm x 230mm

Weight ......................................................................................2.6kg(5lbs. 12oz.)

Revision-B-06242002

2002 © Alpine Electronics of America, Inc. Specifications and design are subject to change without notice

MRP-M200

1 Channel V-Power Series Mono Amplifier

-

Battery

+

Fuse Holder

2 Ohm or 4 Ohm Mono Loading Capable

Speaker Output Lead (+)

Battery Power

Wire (Optional) Power Distribution

Block (Optional)

Battery Lead

Ground Lead (Black)

Speaker Output Lead (-)

MONO

SPEAKER OUTPUT

MONO

25A

BATTERY REMOTE GND

POWER SUPPLY

FUSE

25A

BATTERY REMOTE GND

Remote - Out

SPEAKER OUTPUT

Remote-On Lead (Blue/White)

(+12V Input turns Amp on)

Front Output

White (Left)

Red (Right)

Rear Left (+)

Rear Left (-)

White

Rear Right (-)

Rear Right (+)

White/Black

Grey/Black

Grey

Use Speaker Output or

Low Level Output

(Do Not Use Both)

Optional RCA Cable

0° 180°

PHASE

75

100

140

55

50

170

200

(Hz)

LP FILTER bass engine

+6db NOM

0.5V

0db

OFF ON

BASS EQ

+12db MIN

GAIN

MAX

CH–2 CH–1

(L)

INPUT

(R)

(R) (L)

SPEAKER

LEVEL INPUT

Connector

Assembly

Part No.

01E11136S01

0° 180°

PHASE

75

100

140

55

50

170

200

(Hz)

LP FILTER

+6db NOM

0.5V

0db

OFF ON

BASS EQ

+12db MIN

GAIN

MAX

CH–2 CH–1

(L)

INPUT

(R)

(R) (L)

SPEAKER

LEVEL INPUT

2002 © Alpine Electronics of America, Inc. Specifications and design are subject to change without notice

Revision-B-06242002