Panasonic | CQC1001U | Operating instructions | Panasonic CQC1001U User manual

Panasonic CQC1001U User manual
CD Player/Receiver
FM Stereo Radio
Current consumption
Maximum power output
Tone adjustment range
Suitable speaker impedance
Pre-amp output voltage
Output impedance
Dimensions (W x H x D)
Frequency range
Usable sensitivity
50 dB quieting sensitivity
Frequency response
Alternate channel selectivity
Stereo separation
Image response ratio
IF response ratio
Signal/noise ratio
Operating Instructions
AM Radio
Frequency range
Usable sensitivity
: 530 kHz - 1 710 kHz
: 28 dB/µV (S/N 20 dB)
BAND
APM
PWR
MUTE
7
8
1
Power Output:
14 W RMS x 4 Channels at 4 Ω and ≤ 1%
THD+N (for CQ-C1121/C1101U)
13 W RMS x 4 Channels at 4 Ω and ≤ 1%
THD+N (for CQ-C1001U)
Signal to Noise Ratio:
85 dBA (reference: 1 W into 4 Ω)
: 8 times oversampling
: 1 bit DAC System
: Astigma 3-beam
: Semiconductor laser
: 790 nm
: 20 Hz - 20 kHz (±1 dB)
: 96 dB
: 0.01 % (1 kHz)
: Below measurable limits
: 75 dB
CQ-C1121U
D·M
2
9
3
10
11
12
4
5
6
SQ/SCAN
CLOCK
DO
N
SRC
VO
L
REP
RA
Above specifications comply with EIA standards.
Disc Player
Sampling frequency
DA converter
Pick-up type
Light source
Wave length
Frequency response
Signal to noise ratio
Total harmonic distortion
Wow and flutter
Channel separation
CQ-C1121U/C1101U/C1001U
: 87.9 MHz–107.9 MHz
: 11.0 dBf. (75 Ω)
: 15.2 dBf. (75 Ω)
: 30 Hz–15 kHz (±3 dB)
: 75 dB
: 35 dB (1 kHz)
: 75 dB
: 100 dB
: 62 dB
PUSH SEL
Weight
: 12 V DC (11 - 16 V DC), negative
ground
: Less than 2.2 A (CD mode; 0.5 W 4
channels)
: 50 W x 4 (at 1 kHz), volume control
maximum (for CQ-C1121/C1101U)
: 45 W x 4 (at 1 kHz), volume control
maximum (for CQ-C1001U)
: Bass: ±12 dB at 100 Hz,
Treble: ±12 dB at 10 kHz
:4 - 8 Ω
: 2.5 V (CD mode, 1 kHz, 0 dB)
: 200 Ω
: 178 x 50 x 160 mm
{7" x 1 15/16" x 6 5/16"}
: 1.3 kg {2 lbs. 14 oz}
TUNE/TRACK
Power supply
M
DISP
Panasonic welcomes you to our constantly growing family of electronic products owners.
We endeavor to give you the advantages of precise electronic and mechanical engineering, manufactured with carefully selected components, and
assembled by people who are proud of the reputation their work has built for our company. We know this product will bring you many hours of
enjoyment, and after you discover the quality, value and reliability we have built into it, you too will be proud to be a member of our family.
MUTE
PWR
VOL
MODE
TUNE
TRACK
BAND
CAR AUDIO
Q'ty: 1 set
Installation Instructions
(FX0214C384ZA)
(EUR7641020)
Trim Plate
Q'ty: 1
(YFC054C080ZA: CQ-C1121/1101U)
(YFC054C058ZA: CQ-C1001U)
Q'ty: 1
(FX0214C385ZA)
Q'ty: 1
Owners Information
Card
Mounting Collar
Remote Control Unit
(include a battery, only
for CQ-C1121U)
Lock Cancel Plate
(YFM284C444ZA)
Q'ty: 2
Mounting Bolt
Power Connector
(YEAJ02877)
Q'ty: 1
(YEJV014C002N)
Q'ty: 1
Q'ty: 1
Rubber Bushing
(YES014C095ZA)
Q'ty: 1
Notes:
¡ The number in parentheses underneath each accessory part name is the part number for maintenance and service.
¡ Accessories and their part numbers are subject to modification without prior notice due to improvements.
¡ Mounting Collar and Trim Plate are mounted on the main unit at shipment.
Panasonic Sales Company,
Division of Matsushita Electric of
Puerto Rico, Inc. (“PSC”)
Ave. 65 de Infanteria, Km. 9.5
San Gabriel Industrial Park,
Carolina, Puerto Rico 00985
http://www.panasonic.com
Panasonic Canada Inc.
5770 Ambler Drive,
Mississauga, Ontario
L4W 2T3
http://www.panasonic.ca
YFM284C441ZB TAMACO0904-1015
Note: Battery Information:
Battery Type: Panasonic lithium battery (CR2025) (Included
in the remote control)
Battery Life: Approximately 6 months under normal use (at
room temperature)
ACC
ON
the accessory indicator
lights.
Press [SRC] (PWR: Power).
2
3 Press [DISP] (CLOCK).
4
Your product is designed and manufactured to ensure the minimum of maintenance. Use a soft cloth for routine
exterior cleaning. Never use benzine, thinner, or other solvents.
Press [DISP] (Display) to change the display.
¡ This face plate is not waterproof. Do not expose it to
water or excessive moisture.
¡ Do not remove the face plate while driving your car.
¡ Do not place the face plate on the dashboard or nearby
areas where the temperature rises high.
Rear/Front
Rear
Rear
■ Read the operating instructions for the unit and all other components of your car audio system carefully before using the system.
They contain instructions about how to use the system in a safe and
effective manner. Panasonic assumes no responsibility for any problems resulting from failure to observe the instructions given in this
manual.
This pictograph intends to alert you to the presence of
important operating instructions and installation instructions. Failure to heed the instructions may result in
severe injury or death.
Warning
Observe the following warnings when using this
unit.
Watching the display or operating the system will distract the driver from looking ahead of the vehicle and can cause accidents.
Always stop the vehicle in a safe location and use the parking
brake before watching the display or operating the system.
❑ Use the proper power supply.
¡ Do not touch the contacts on the face plate and the main
unit, since this may result in poor electrical contact.
¡ If dirt or other foreign substances get on the contacts,
wipe them off with a clean and dry cloth.
This product is designed for operation with a negative grounded
12 V DC battery system. Never operate this product with other battery systems, especially a 24 V DC battery system.
❑ Keep batteries and insulation film out of reach of infants.
Batteries and insulation film can be ingested, so keep them out of
the reach of infants. If an infant ingests a battery or insulation film,
please seek immediate medical attention.
❑ Protect the Deck Mechanism.
Do not insert any foreign objects into the slot of this unit.
❑ Do not disassemble or modify the unit.
(Anti-Theft System)
Face Plate Removing/Mounting
Clock Setting
Caution
6 Press [DISP] (CLOCK).
Notes:
¡ "AdJ" is displayed before adjusting the clock.
¡ Hold down []] or [[] to change numbers rapidly.
Pre-amp. output connector
❑ The driver should neither watch the display nor operate
the system while driving.
Anti-Theft System
[[]: sets the hour ahead.
[]]: sets the hour back.
8 Press [DISP] (CLOCK).
No
LIMITED WARRANTY COVERAGE
If your product does not work properly because of defects in materials
and workmanship.
Panasonic Consumer Electronics Company or Panasonic Sales Company
(collectively referred to as “the warrantor”) will, for the length of the period indicated in the chart below, which starts with the date of original purchase (“warranty period”), at its option either (a) repair your product with
new or refurbished parts, or (b) replace it with a new or refurbished
product. The decision to repair or replace will be made by the warrantor.
Categories
CANADA
WARRANTY SERVICE
For product operation and information assistance, please
contact your Dealer or our Customer Care Centre at:
Telephone #: (905) 624-5505 Fax #: (905) 238-2360
Web: www.panasonic.ca
For product repairs, please contact one of the following:
・Your Dealer who will inform you of an authorized
Servicentre nearest you.
・Our Customer Care Centre at (905) 624-5505 or
www.panasonic.ca
・A Panasonic Factory Servicentre listed below:
Richmond, British
Columbia
Panasonic Canada Inc.
12111 Riverside Way
Richmond, BC V6W 1K8
Tel: (604) 278-4211
Fax: (604) 278-5627
Calgary, Alberta
Panasonic Canada Inc.
6835-8th St. N. E. Calgary,
AB T2E 7H7
Tel: (403) 295-3955
Fax: (403) 274-5493
Mississauga, Ontario
Panasonic Canada Inc.
5770 Ambler Dr.
Mississauga, ON L4W 2T3
Tel: (905) 624-8447
Fax: (905) 238-2418
Lachine, Quebec
Panasonic Canada Inc.
3075, rue Louis A. Amos
Lachine, QC H8T 1C4
Tel: (514) 633-8684
Fax: (514) 633-8020
Parts
Labor
Do not disassemble, modify the unit or attempt to repair the product yourself. If the product needs to be repaired, consult your
dealer or an authorized Panasonic Servicenter.
Removing
Mounting
1
2 Press [ ]. The face plate will open.
3 Pull it out toward you.
1 Slide the left side of the face plate in place.
2 Press the right end of the face plate until a
Turn off the power.
“click” is heard.
❑ Do not use the unit when it is out of order.
If the unit is out of order (no power, no sound) or in an abnormal
state (has foreign matter in it, is exposed to water, is smoking, or
smells), turn it off immediately and consult your dealer.
❑ The remote control unit should not lie about in the car.
If the remote control unit lies about, it could fall on the floor while
driving, get wedged under the brake pedal, and lead to a traffic
accident.
2
1
1
2
Customer’s Record
Model
No.
Serial
No.
Dealer’s
No.
Code
No.
Dealer’s
Audio Components (except items listed below)
One (1) Year
One (1) Year
Address
Date of
MXE Series Audio Components (except items
listed below)
Speakers
Two (2) Years
Two (2) Years
Purchase
One (1) Year
Not Applicable
Accessories (in exchange for defective items)
Ninety (90) Days Not Applicable
CANADA
During the “Labor” warranty period, there will be no charge for labor.
During the “Parts” warranty period, there will be no charge for parts. You
must carry in or mail in your product during the warranty period. If nonrechargeable batteries are included, they are not warranted. This warranty
only applies to products purchased and serviced in the United States or
Puerto Rico. This warranty is extended only to the original purchaser of a
new product which was not sold “as is”. A purchase receipt or other
proof of the original purchase date is required for warranty service.
CARRY-IN OR MAIL-IN SERVICE
For Carry-In or Mail-In Service in the United States, call 1-800-211-PANA
(7262) or visit
Panasonic Web Site: http://www.panasonic.com
For assistance in Puerto Rico, call Panasonic Sales Company (787)-7504300 or fax (787)-768-2910.
LIMITED WARRANTY LIMITS AND EXCLUSIONS
This warranty ONLY COVERS failures due to defects in materials and
workmanship, and DOES NOT COVER normal wear and tear or cosmetic
damage. The warranty ALSO DOES NOT COVER damages which
occurred during shipment, failures which are caused by products not
supplied by the warrantor, failures which result from accident, misuse,
abuse, neglect, mishandling, misapplication, alteration, faulty installation,
set-up adjustment, maladjustment of consumer control, improper maintenance, improper antenna, inadequate signal reception or pickup, power
line surge, improper voltage supply, lightning, modification, commercial
use (such as use in hotels, offices, restaurants, or other business uses)
or rental use of the product, or service by anyone other than the technician from Factory Servicenter or other authorized service centers, or
damage that is attributable to acts of God.
THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER
“LIMITED WARRANTY COVERAGE”. THE WARRANTOR IS NOT LIABLE
FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM
THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF
THIS WARRANTY. (As examples, this excludes damages for lost time,
cost of having someone remove or re-install an installed unit if applicable, travel to and from the sevicer, and loss of media, data or other memory contents. The items listed are not exclusive, but are for illustration
only.) ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE
WARRANTY OF MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF
THE LIMITED WARRANTY.
■ This manual uses pictographs to show you how to use the product
safely and to alert you to potential dangers resulting from improper
connections and operations. The meanings of the pictographs are
explained below. It is important that you fully understand the meanings of the pictographs in order to use this manual and the system
properly.
Caution
This pictograph intends to alert you to the presence of
important operating instructions and installation instructions. Failure to heed the instructions may result in
injury or material damage.
Caution
Observe the following cautions when using this
unit.
❑ Keep the sound volume at an appropriate level.
Keep the volume level low enough to be aware of road and traffic
conditions while driving.
❑ This unit is designed for use exclusively in automobiles.
❑ Do not operate the unit for a prolonged period with the
engine turned off.
Operating the audio system for a long period of time with the
engine turned off will drain the battery.
¡ Use fuses of the same specified rating (15 A). Using substitutes or fuses with higher ratings, or connecting the unit
directly without a fuse could cause fire or damage to the unit. If the replaced fuse fails, contact your nearest authorized
Panasonic Servicenter.
Display off
5 Adjust the hour.
[[]: sets the minute ahead.
[]]: sets the minute back.
No
Warning
This unit is equipped with a removable face plate. Removing this face plate makes the unit totally inoperable.
7 Adjust the minute.
Yes (Included)
Matsushita Electric of Puerto Rico, Inc.
Panasonic Sales Company
Factory Servicenter:
Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park,
Carolina, Puerto Rico 00985
Phone (787) 750-4300, Fax (787) 768-2910
Warning
Clock display
Hold down [DISP] (CLOCK) for more than
2 seconds.
Remote control function
PARTS AND SERVICE WHICH ARE NOT COVERED BY THIS LIMITED
WARRANTY ARE YOUR RESPONSIBILITY.
PANASONIC AUTO PRODUCTS
LIMITED WARRANTY
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga Ontario L4W 2T3
PANASONIC PRODUCT LIMITED WARRANTY
Panasonic Canada Inc. warrants this product to be free from defects in
materials and workmanship and agrees to remedy any such defect for a
period as stated below from the date of original purchase.
CAR AUDIO PRODUCT – ONE (1) YEAR, PARTS AND LABOUR
(The labour to install or remove the product is not warranted)
LIMITATIONS AND EXCLUSIONS
This warranty does not apply to products purchased outside Canada or to
any product which has been improperly installed, subjected to usage for
which the product was not designed, misused or abused, damaged during shipping, or which has been altered or repaired in any way that
affects the reliability or detracts from the performance, nor does it cover
any product which is used commercially. Dry cell batteries are also
excluded from coverage under this warranty.
This warranty is extended to the original end user purchaser only. A purchase receipt or other proof of the original purchase date is required
before warranty service is performed.
THIS EXPRESS, LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE.
IN NO EVENT WILL PANASONIC CANADA INC. BE LIABLE FOR ANY
SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES.
In certain instances, some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, or the exclusion of
implied warranties, so the above limitations and exclusions may not be
applicable.
IF YOU SHIP THE PRODUCT TO A SERVICENTRE
Carefully pack and send prepaid, adequately insured and preferably in the
original carton.
Include details of the defect claimed, and proof of the date of original
purchase.
Safety Information
If the replaced fuse fails, contact your nearest authorized Panasonic Servicenter.
Clock Display at Power Off
Fuse
Battery
Installation
1 Turn the ignition switch until
Button
Purchase Parts, Accessories and Instruction Books online
for all Panasonic Products by visiting our Web Site at:
http://www.pasc.panasonic.com
or, send your request by E-mail to:
npcparts@panasonic.com
You may also contact us directly at:
1-800-332-5368 (Phone) 1-800-237-9080 (Fax Only)
(Monday-Friday 9 am to 8 pm, EST.)
Panasonic Services Company
20421 84th Avenue South, Kent, WA 98032
(We accept Visa, MasterCard, Discover Card, American
Express, and Personal Checks)
For hearing or speech impaired TTY users, TTY : 1-886-6051277
Printed in China
Maintenance
The 12-hour system is used for the clock.
Rotary knob
Accessory Purchases:
¡Please read these instructions (including “Limited Warranty” and “Customer Services Directory”) carefully before using this product
and keep this manual for future reference.
Preparation
Pull the insulation film out from
the backside of the remote control gently.nly
Rotary knob
Features
Volume control
Service in Puerto Rico
Cleaning the
Unit
Panasonic Consumer Electronics
Company, Division of Matsushita
Electric Corporation of America
One Panasonic Way, Secaucus,
New Jersey 07094
http://www.panasonic.com
CQ-C1001U
Obtain Product Information and Operating Assistance;
locate your nearest Dealer or Servicenter; purchase Parts
and Accessories; or make Customer Service and Literature
requests by visiting our Web site at:
http://www.panasonic.com/support
or, contact us via the web at:
http://www.panasonic.com/contactinfo
You may also contact us directly at:
1-800-211-PANA (7262),
Monday-Friday 9 am-9 pm; Saturday-Sunday 10 am-7 pm,
EST.
For hearing or speech impaired TTY users, TTY : 1-877-8338855
Note:
¡ Specifications and design are subject to modification without
notice due to improvements.
¡ Some figures and illustrations in this manual may be different
from your product.
Q'ty: 1
CQ-C1101U
U.S.A.
Customer Services Directory
POWER
(English: YFM284C441ZA)
(Français: YFM284C442ZA)
(Español: YFM284C443ZA)
CQ-C1121U
This warranty gives you specific legal rights and you may also have other
rights which vary from state to state. If a problem with this product
develops during or after the warranty period, you may contact your dealer or Servicenter. If the problem is not handled to your satisfaction, then
write to warrantor’s Consumer Affairs Department at the addresses of the
warrantor.
PANASONIC SALES COMPANY,
DIVISION OF MATSUSHITA ELECTRIC OF PUERTO RICO, INC.
Ave. 65 de infanteria, Km. 9.5, San Gabriel Industrial Park
Carolina, Puerto Rico 00985
(CQ-C1121U)
Accessories
Operating Instructions
PANASONIC CONSUMER ELECTRONICS COMPANY,
DIVISION OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA
One Panasonic Way, Secaucus, New Jersey 07094
This operating instruction manual is for 3 models CQ-C1121U, CQ-C1101U and CQ-C1001U. All illustrations throughout this
manual represent model CQ-C1121U unless otherwise specified. The following table describes the differences among 3 models.
Models
Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty
lasts, so the exclusions may not apply to you.
U.S.A.
Limited Warranty
General
Before Reading These Instructions
Differences Among
3 Models
Specifications
English
®
❑ Refer fuse replacement to qualified service personnel.
When the fuse burns out, eliminate the cause and have it replaced
with the fuse prescribed for this unit by a qualified service engineer. Incorrect replacement of the fuse may lead to smoke, fire,
and damage to the product.
Observe the following warnings when installing.
❑ Disconnect the lead from the negative (–) battery terminal before installation.
Wiring and installation with the negative (–) battery terminal connected may cause electrical shock and injury due to a short circuit.
Some cars equipped with the electrical safety system have specific
procedures of battery terminal disconnection.
FAILURE TO FOLLOW THE PROCEDURE MAY LEAD TO THE
UNINTENDED ACTIVATION OF THE ELECTRICAL SAFETY SYSTEM
RESULTING IN DAMAGE TO THE VEHICLE AND PERSONAL
INJURY OR DEATH.
❑ Never use safety-related components for installation,
grounding, and other such functions.
Do not use safety-related vehicle components (fuel tank, brake,
suspension, steering wheel, pedals, airbag, etc.) for wiring or fixing the product or its accessories.
❑ Installing the product on the air bag cover or in a location
where it interferes with airbag operation is prohibited.
❑ Check for piping, gasoline tank, electric wiring, and other
items before installing the product.
If you need to open a hole in the vehicle chassis to attach or wire
the product, first check where the wire harness, gasoline tank, and
electric wiring are located. Then open the hole from outside if possible.
❑ Never install the product in a location where it interferes
with your field of vision.
❑ Never have the power cord branched to supply other
equipment with power.
❑ After installation and wiring, you should check the normal operation of other electrical equipment.
The continuation of their using in abnormal conditions may cause
fire, electrical shock or a traffic accident.
❑ In the case of installation to an airbag-equipped car, confirm warnings and cautions of the vehicle manufacturer
before installation.
❑ Make sure the leads do not interfere with driving or getting in and out of the vehicle.
❑ Insulate all exposed wires to prevent short circuiting.
❑ Do not expose the unit to direct sunlight or excessive
heat.
Otherwise these will raise the interior temperature of the unit,
and it may lead to smoke, fire, or other damage to the unit.
❑ Do not use the product where it is exposed to water,
moisture, or dust.
Exposure of the unit to water, moisture, or dust may lead to
smoke, fire, or other damage to the unit. Make especially sure
that the unit does not get wet in car washes or on rainy days.
Observe the following cautions when installing.
❑ Refer wiring and installation to qualified service personnel.
Installation of this unit requires special skills and experience. For
maximum safety, have it installed by your dealer. Panasonic is
not liable for any problems resulting from your own installation
of the unit.
❑ Follow the instructions to install and wire the product.
Not following the instructions to properly install and wire the
product could cause an accident or fire.
❑ Take care not to damage the leads.
When wiring, take care not to damage the leads. Prevent them
from getting caught in the vehicle chassis, screws, and moving
parts such as seat rails. Do not scratch, pull, bend or twist the
leads. Do not run them near heat sources or place heavy objects
on them. If leads must be run over sharp metal edges, protect
the leads by winding them with vinyl tape or similar protection.
❑ Do not install the product where it is exposed to strong
vibrations or is unstable.
Avoid slanted or strongly curved surfaces for installation. If the
installation is not stable, the unit may fall down while driving and
this can lead to an accident or injury.
❑ Installation Angle
The product should be installed in a horizontal position with the
front end up at a convenient angle, but not more than 30˚.
The user should bear in mind that in some areas there may be
restrictions on how and where this unit can be installed. Consult
your dealer for further details.
❑ Wear gloves for safety. Make sure that wiring is completed before installation.
❑ To prevent damage to the unit, do not connect the
power connector until the whole wiring is completed.
❑ Do not connect more than one speaker to one set of
speaker leads. (except for connecting to a tweeter)
Observe the following cautions when handling the
battery for the remote control unit.
● Use only specified battery (CR2025).
● Match the polarity of the battery with the (+) and (–) marks in
the battery case.
● Replace dead battery as soon as possible.
● Remove the battery from the remote control unit when not using
it for an extended period of time.
● Insulate the battery (by placing them in a plastic bag or covering
them with vinyl tape) before disposal or storage.
● Dispose of the battery according to the local regulations.
● Do not disassemble, recharge, heat or short the battery. Do not
throw a battery into a fire or water.
In case of battery leakage
● Thoroughly wipe the battery liquid off the battery case and insert
new battery.
● If any part of your body or clothing comes into contact with battery liquid, wash it with plenty of water.
● If battery liquid comes into contact with your eyes, wash them
with plenty of water and get immediate medical attention.
❑ Use the designated parts and tools for installation.
Use the supplied or designated parts and appropriate tools to
install the product. The use of parts other than those supplied or
designated may result in internal damage to the unit. Faulty
installation may lead to an accident, a malfunction or fire.
❑ Do not block the air vent or the cooling plate of the unit.
Blocking these parts will cause the interior of the unit to overheat and will result in fire or other damage.
The following applies only in the U.S.A.
Part 15 of the FCC Rules
FCC Warning:
Any unauthorized changes or modifications to this equipment
would void the user's authority to operate this device.
Caution
THIS PRODUCT IS A CLASS I LASER PRODUCT.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR BY YOURSELF.
REFER SERVICING TO QUALIFIED PERSONNEL.
CQ-C1001U
CQ-C1121U
TUNE/TRACK
2
3
10
11
12
4
5
6
SQ/SCAN
CQ-C1121U
PWR
CLOCK
REP
DO
M
MUTE
SRC
D·M
7
1
8
2
9
3
10
11
12
4
5
6
SQ/SCAN
CLOCK
DO
N
1
9
L
APM
REP
RA
8
N
7
RA
MUTE
SRC
D·M
PUSH SEL
APM
PWR
MUTE
SRC
PUSH SEL
UME
VOL
SEL
BAND
CQ-C1121U
M
DISP
DISP
[DISP] (Display)
switches the information on
the display.
Preset Number
Press [DISP] (Display) to change the display.
Radio mode display (Default)
CQ-C1001U
Clock display
lights while receiving the D•M (Direct Memory)
station.
Volume Adjustment
(VOCAL) clear sound:
emphasizes middle tone and slightly emphasizes treble.
(Setting Range: 0 to 40, Default: 18)
CQ-C1101U
Turn [VOL] (Volume).
CQ-C1001U
2
Frequency adjustment
Press [BAND] to select a band.
Note: Settings of SQ, bass and treble are influenced
[TRACK s] [TRACK d]
skip to the previous/next track in the player
mode.
Hold down either of them for fast reverse/fast
forward.
Disc slot
takes a disc in with the label-side facing up.
Note: The power will be turned on automatically
when a disc is loaded.
MUTE
[VOL}] [VOL{]
adjust the volume.
VO
BAND
L
CQ-C1121U
PUSH SEL
(y / 5) (Pause/Play)
toggles pause/play in the player source.
[u] (Eject)
ejects the disc.
APM
PWR
1
TUNE
TRACK
[BAND]
selects a band in the radio source,
toggles pause/play in the player source,
and executes APM in the radio source.
(Hold down it for more than 2 seconds.)
BAND
CAR AUDIO
[TUNE]] [TUNE[]
down/up the frequency. (Hold down it for
more than 2 seconds for seek tuning.)
[TRACK s ] [TRACK d ]
skip to the previous/next track in the player mode.
Hold down it for fast reverse/fast forward.
[SRC] (Source)
selects a source
8
2
9
3
w Put a battery in the case
with (+)-side facing up.
e Put the case back.
2
3
¡ Do not insert a disc when the
indicator lights.
¡ Refer to the section of “Notes on Discs”.
¡ This unit does not support 8 cm {3"} discs.
¡ If you insert an 8 cm {3"} disc and cannot eject it, turn ACC of
your car off once and turn it on again, then press [u] (Eject).
Warning
¡Keep batteries away from children to avoid the risk
of accidents. If an infant ingests a battery, please
seek immediate medical attention.
Caution
¡ Remove and dispose of the old battery immediately.
¡ Do not disassemble, heat or short the battery. Do
not throw the battery into a fire or water.
¡ Follow local regulations when disposing of the
battery.
¡Improper use of batteries may cause overheating,
an explosion or ignition, resulting in injury or a
fire.
Note: Battery Information:
Battery Type: Panasonic lithium battery (CR2025)
(Included in the remote control)
Battery Life: Approximately 6 months under normal
use (at room temperature)
12
5
6
SQ/SCAN
CLOCK
DO
[DISP] (Display)
switches the information on
the display.
[REP] (Repeat)
toggles on/off the repeat play.
(RANDOM)
toggles on/off the random play. (Hold down it
for more than 2 seconds.)
REP
M
DISP
(SCAN)
toggles on/off the scan play. (Hold down it for more than 2
seconds.)
Operation Flow
Battery Notes
Tough pointed object
q Remove the battery holder
with the remote control unit
placed on a flat surface.
q Stick your thumbnail into
the groove, and push the
holder in the direction of
the arrow, and at the
same time.
w
w Pull it out in the direction
q
of the arrow using a
tough pointed object.
Back side
11
4
[1] to [6]
(7) to (12) (Hold down one of them for
more than 2 seconds.)
select a track directly.
Caution
Battery Replacement
10
N
7
RA
MUTE
SRC
D·M
TUNE/TRACK
VOL
6
SQ/SCAN
CLOCK
DO
REP
M
DISP
MUTE
SRC
Note: If no operation takes place for more than 5 seconds
in the audio menu (2 seconds in Main volume adjustment),
the display returns to the regular mode.
CQ-C1101U
1 Select a band.
2 Hold down [BAND] (APM) for more than 2
CQ-C1101U
[▲]
[▼]
CQ-C1001U
Press [SEL] (Select).
Press [▲] or [▼].
(Setting Range: 0 to 40, Default: 18)
Note: New stations overwrite existing saved stations.
[▲]: Up
[▼]: Down
Bass
(Setting Range: –12 dB to +12 dB by 2 dB,
Default: 0 dB)
[▲]: Up
[▼]: Down
Treble
(Setting Range: –12 dB to +12 dB by 2 dB,
Default: 0 dB)
Your favorite FM/AM radio station can be memorized in the
[D·M] button and you can call back the radio station just by
pressing the button whatever the current sound source is,
even if the power is off.
D•M station writing
[▲]: Up
[▼]: Down
Balance
1 Select a station you would like to preset.
2 Hold down [D•M] for more than 2 seconds.
(Setting Range: 15 levels each and 0 (center),
Default 0)
[▲]: Right enhanced
[▼]: Left enhanced
Fader
D•M station calling
1
CQ-C1121U
Turn [VOL].
Volume
(blinks once)
seconds.
3 Adjust.
CQ-C1101U
With this operation, stations with good receiving conditions can
be automatically stored in the preset memory.
(Setting Range: 15 levels each and 0 (center),
Default 0)
Press [D•M] (Direct Memory).
[▲]: Front enhanced
[▼]: Rear enhanced
Note: If the fader is set to front, the pre-amp. output
(rear) is decreased.
1
Press [SRC] (Source) to select the Disc
Player mode.
2
Select a desired portion.
¡ This unit does not support MP3 and WMA disc playback.
¡ This unit does not support CD text display.
¡ Do not insert foreign matter into the disc slot.
Play time
If You Suspect Something Wrong
Display change
Track
Check and take steps as described below.
Press [DISP] (Display) to change the display.
If the described suggestions do not solve the problem, it is recommended to take the unit to your nearest authorized Panasonic
Servicenter. The product should be serviced only by qualified personnel. Please refer checking and repair to professionals. Panasonic
shall not be liable for any accidents arising out of neglect of checking
the unit or your own repair after your checking.
Player mode display (Default)
lights when a disc is in the player.
Repeat indicator
Trouble
Random play
All the available tracks are played in a random sequence.
Hold down [REP] (RANDOM) for more than
2 seconds.
Scan play
The first 10 seconds of each track is played in sequence.
Hold down [SQ] (SCAN) for more than 2
seconds.
Press [TRACK s] or [TRACK d].
Press a track number button from [1] to [6].
¡ The corresponding track (1-6) starts playing.
Hold down a track number button from [1]
to [6] ((7) to (12)) for more than 2 seconds.
¡ The corresponding track (7-12) starts playing.
No power
Hold down again to cancel.
Repeat play
The current track is repeated.
(blinks during scanning)
Hold down again to cancel.
No sound
Press [REP] (Repeat).
Noise
Press again to cancel.
Notes on CD/CD Media
Press again to cancel.
Direct track selection
Check point
Common
Press [BAND] (y / 5).
Warning
¡ Do not use the unit in an irregular condition, for example,
without sound, or with smoke or a foul smell, which can cause
ignition or electric shock. Immediately stop using the unit and
consult your dealer.
¡ Never try to repair the unit by yourself because it is dangerous
to do so.
Clock display
Pause
Track selection
Note: To perform fast forward/reverse, hold down either
of them.
Random indicator
Player Mode Display
[MUTE]
toggles mute on/off.
MODE
12
5
Troubleshooting
Random, Repeat, Scan
Note: This operating instruction manual explains operations for use with the buttons on the main unit. (Different operations excluded)
[MODE]
selects a mode (source).
11
4
CQ-C1001U
[1] to [6] for more than 2 seconds.
Auto Preset Memory (APM)
Disc Player
Notes on Discs
Remote Control Unit (Only for C1121U)
PWR
10
[DISP] (Display)
exits from the audio menu.
Press [VOL] (PUSH SEL: Select).
Press again to cancel.
to the audio signal, readjust bass/treble or volume.
POWER
SEL
PWR
CQ-C1121U
1 Tune into a station.
2 Hold down one of the preset buttons from
Note: New stations overwrite existing saved stations.
Preset station selection
Press the corresponding preset button from [1] to [6] to
tune into a preset station.
by one another. If such an influence causes distortion
[PWR] (Power)
toggles power on/off.
APM
2 Select a mode to be adjusted.
Manual station preset
The preset stations under best receiving conditions are
received for 5 seconds each after presetting the stations
(SCAN). To stop scanning, press one of the preset buttons from [1] to [6].
Note: Hold down either of them for more than 0.5
seconds and release it for station search.
Mute
lights.)
3
CQ-C1001U
[TUNE]]: Lower
[TUNE[]: Higher
Press [VOLUME▲] or [VOLUME▼].
ON: Press [MUTE]. (
OFF: Press [MUTE] again.
9
2
Press [SEL] (Select).
Audio menu
Disc Player
3 Select a station.
source.
(ROCK) speedy and heavy sound:
exaggerates bass and treble.
(POP) wide-ranged and deep sound:
slightly emphasizes bass and treble.
CQ-C1121U
1 Press [SRC] (Source) to select the radio
Operation Flow
General Operations
Press [SRC] (Source) to change the source.
8
1 Display the audio menu.
Up to 6 stations can be preset in AM, FM1, FM2, and FM3
respectively.
Preset stations can be simply called up by pressing one of the
preset buttons from [1] to [6].
SQ is a function that can call up various sound types at
the touch of button in accordance with your listening
music type.
Press [SQ] to select the sound type as follows:
(FLAT) flat frequency response:
does not emphasize any part. (Default)
Source Selection
7
BAND
[▲] or [▼]
selects a value in the audio menu.
[SEL] (Select)
selects items in the audio menu.
[TUNE ]] [TUNE []
down/up the frequency. (Hold down it for
more than 2 seconds for seek tuning.)
Preset buttons [1] to [6]
selects a preset station in the radio source,
and presets the current station. (Hold down it
for more than 2 seconds)
Station Preset
Power on: Press [SRC] (PWR: Power).
Power off: Hold down [SRC] (PWR: Power) for
more than 1 second.
Radio
[SRC] (Source)
selects a source.
SQ (Sound Quality)
Turn your car's ignition switch to the ACC or ON position.
MUTE
SRC
CQ-C1121U
Direct Memory
Power On/Off
PWR
D·M
Press [VOL] (PUSH SEL: Select).
[SQ] (Sound Quality)
selects a sound type (SQ).
[MUTE]
toggles mute on/off.
CQ-C1121U
APM
1
lights when mute is on.
[SRC] (Source)
selects a source.
(PWR) (Power)
toggles power on/off.
VO
L
BAND
N
VO
L
BAND
APM
PWR
VO
Band
CQ-C1101U
[VOL]
selects a value in the audio menu.
(PUSH SEL) (Push to Select)
selects items in the audio menu.
UME
VOL
BAND
Remote Control Sensor
Frequency
CQ-C1121U
Display change
RA
[VOLUME▲] [VOLUME▼] (Press)
adjusts the volume.
lights while receiving an FM stereo signal.
Radio Mode Display
[VOL] (Volume) (Turn)
[D•M] (Direct Memory)
tunes into the station memorized in D•M.
(Hold down it for more than 2 seconds to
memorize the current station.)
[BAND]
selects a band in the radio source.
(APM) (Auto Preset Memory)
executes APM in the radio source. (Hold
down it for more than 2 seconds)
PUSH SEL
[D•M] (Direct Memory)
tunes into the station memorized in D•M.
(Hold down it for more than 2 seconds to
memorize the current station.)
CQ-C1101U
Audio Setting
TUNE/TRACK
CQ-C1121U
Radio (AM/FM )
TUNE/TRACK
General
If you use commercial CDs, they must
have the label shown at right.
Some copy-protected music CDs are not
playable.
How to hold a disc
¡ Do not touch the underside of a disc.
¡ Do not scratch on a disc.
¡ Do not bend a disc.
¡ When not in use, keep a disc in a case.
Do not use irregularly shaped discs.
Do not leave discs in the following places:
¡ Direct sunlight
¡ Near car heaters
¡ Dirty, dusty and damp areas
¡ Seats and dashboards
Disc cleaning
Use a dry, soft cloth to wipe from the center outward.
Do not attach any seals or labels to your discs.
Do not write on the disc label with a ballpoint pen
or other hard-point pens.
Notes on CD-Rs/RWs
¡ You may have trouble playing back some CD-R/RW discs
recorded using CD recorders (CD-R/RW drives), either due
to their recording characteristics or dirt, fingerprints,
scratches, etc. on the disc surface.
¡ CD-R/RW discs are less resistant to high temperatures and
high humidity than ordinary music CDs. Leaving them
inside a car for extended periods may damage them and
make playback impossible.
¡ Some CD-R/RWs cannot be played back successfully due
to incompatibility among writing software, a CD recorder
(CD-R/RW drive) and the discs.
¡ This player cannot play the CD-R/RW discs if the session is
not closed.
¡ This player cannot play the CD-R/RW discs which contain
other than CD-DA data (MP3/WMA, Video CD, etc.).
¡ Be sure to observe the instructions of the CD-R/RW disc
for handling it.
No sound from
left, right, front,
or rear speaker
Left and right
sounds are
reversed
Check point
Trouble
Disc Player
¡ Start the engine. (Or turn the ignition
switch to the ACC position.)
¡ Verify the wiring. (Ex. battery lead,
power lead, ground lead, etc.)
¡ Fuse blown (Contact the nearest
Panasonic Servicenter.)
¡ Ask a professional for fuse replacement.
¡ Be sure to use the same rated fuse.
¡ Disable the mute function.
¡ Verify the wiring.
¡ Wait until the dew disappears before
turning on the unit.
¡ Make sure that grounding is established
properly.
¡ Adjust the balance and fader.
¡ Verify the wiring.
¡ Connect the speaker lead correctly.
No sound, or disc
is automatically
ejected
¡ Load the disc correctly.
¡ Clean the disc.
Sound skip,
poor sound
quality
¡ Clean the disc.
Sound skip
due to
vibration
¡ The maximum permissible tilt angle is
30°.
¡ Secure the unit.
Disc not
ejectable
¡ Press [u]. If the disc is still not ejected,
contact the nearest Panasonic
Servicenter.
Error Display Messages
(The disc is ejected automatically.)
The disc is dirty, or is upside down.
The disc has scratches.
¡ Check the disc.
Radio
Frequent
noise
¡ Tune into another station of high-intensity waves.
¡ Make sure that the antenna mounted
point is grounded properly.
Preset data
are deleted
¡ The preset memory is cleared to return
to the original factory setting when the
power connector or battery is disconnected.
No operation by some cause.
¡ If normal operation is not restored, call
the store where you purchased the unit
or the nearest Servicenter to ask for
repairs.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising