Zenith DVB352 Operating Guide

Installation and Operating Guide | Warranty
Model Number | DVB352 | DVD Player
© Copyright 2003, Zenith Electronics Corporation
Safety Precautions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK
OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This lightning flash with arrowhead symbol within an
equilateral triangle is intended to alert the user to
the presence of uninsulated dangerous voltage
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
product.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH
WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE
DANS LA BORNE CORRESPONDANTE DE LA PRISE ET
POUSSER JUSQU’AU FOND.
WARNING: Do not install this equipment in a confined space
such as a bookcase or similar unit.
CAUTION:
This Digital Video Disc Player employs a Laser System.
To ensure proper use of this product, please read this owner’s
manual carefully and retain for future reference. Should the unit
require maintenance, contact an authorized service
location (see ‘How service is handled’ on warranty).
Use of controls, adjustments, or the performance of procedures
other than those specified herein may result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open
the enclosure. Visible laser radiation when open. DO NOT
STARE INTO BEAM.
CAUTION: The apparatus should not be exposed to water
(dripping or splashing) and no objects filled with liquids, such
as vases, should be placed on the apparatus.
2
FCC WARNING: This equipment may generate or use radio
frequency energy. Changes or modifications to this
equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The
user could lose the authority to operate this equipment if an
unauthorized change or modification is made.
REGULATORY INFORMATION: FCC Part 15
This product has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the product is
operated in a residential installation. This product generates,
uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur
in a particular installation. If this product does cause harmful
interference to radio or television reception, which can be
determined by turning the product off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the product and
receiver.
Connect the product into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician
for help.
FCC COMPLIANCE: The responsible party for this product’s
compliance is: Zenith Electronics Corporation, 2000 Millbrook
Drive, Lincolnshire, IL 60069, USA.
Phone: 1-847-941-8000
OTES ON COPYRIGHTS:
It is forbidden by law to copy, broadcast, show, broadcast
via cable, play in public, or rent copyrighted material without
permission.
This product uses copyright protection developed by
Macrovision. Copy protection signals are recorded on some
discs. When recording and playing the pictures of these discs
on a VCR, picture noise will appear.
This product incorporates copyright protection technology that
is protected by method claims of certain U.S. patents and other
intellectual property rights owned by Macrovision Corporation
and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is
intended for home and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
SERIAL NUMBER: The serial number is found on the back of
this unit. This number is unique to this unit and not available to
others. You should record requested information here and
retain this guide as a permanent record of your purchase.
Model No. DVB352
Serial No.
Date of Purchase
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNER’S MANUAL.
AND THOSE MARKED ON THE PRODUCT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE.
This product has been designed and manufactured to assure personal safety. Improper use can result in electric
shock or fire hazard. The safeguards incorporated in this product will protect you if you observe the following procedures for installation, use, and servicing.
This product does not contain any parts that can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.
1. Read these instructions. - All these safety and operating instructions should be read before the product is
operated.
2. Keep these instructions. - The safety, operating and
use instructions should be retained for future reference.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the product.
11. Only use attachments/accessories specified by
the manufacturer.
3. Heed all warnings. - All warnings on the product and
in the operating instructions should be adhered to.
4. Follow all instructions. - All operating and use
instructions should be followed.
5. Do not use this product near water. – For example:
near a bath tub, wash bowl, kitchen sink, laundry tub,
in a wet basement; or near a swimming pool; and other
areas located near water.
6. Clean only with dry cloth. – Unplug this product from
the wall outlet before cleaning. Do not use liquid cleaners.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions. Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product
and to protect it from over-heating. The openings
should never be blocked by placing the product on a
bed, sofa, rug or other similar surface. This product
should not be placed in a built-in installation such as a
bookcase or rack unless proper ventilation is provided
or the manufacturer’s instructions have been adhered
to.
12. Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/product combination to
avoid injury from tip-over.
13. Unplug this product during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the product has been
damaged in any way, such as power-supply cord
or plug is damaged, liquid has been spilled or
objects have fallen into the product, the product
has been exposed to rain or moisture, does not
operate normally, or has been dropped.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9.
Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
3
INTRODUCTION
IMPORTANT SAFETY INSTRUCTIONS
Table of Contents
Introduction
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . 2
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . 3
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Before Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Playable Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Notes on Discs . . . . . . . . . . . . . . . . . . . . . . . . . . 6
About Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Front Panel and Display Window . . . . . . . . . . . . . . 7
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
DVD Connections Panel . . . . . . . . . . . . . . . . . . . . . 9
Preparation
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11
Connecting to a TV . . . . . . . . . . . . . . . . . . . . . . 10
Optional Equipment Connections . . . . . . . . . . . . 11
Pre-operation . . . . . . . . . . . . . . . . . . . . . . . . . . 12-15
General Explanation. . . . . . . . . . . . . . . . . . . . . . 12
On-Screen Display . . . . . . . . . . . . . . . . . . . . . . . 12
Pre-operation Settings. . . . . . . . . . . . . . . . . . 13-15
Pre-operation Setup. . . . . . . . . . . . . . . . . . . 13
Language . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Picture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Others . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Parental Control. . . . . . . . . . . . . . . . . . . . . . 15
Operation
DVD Operation . . . . . . . . . . . . . . . . . . . . . . . . . 16-18
Playing a DVD . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Exchanging discs during playback . . . . . . . . 16
Skipping discs . . . . . . . . . . . . . . . . . . . . . . . 16
Exchanging the disc and starting playback . . 16
General Features . . . . . . . . . . . . . . . . . . . . . . . . 17
Moving to another TITLE . . . . . . . . . . . . . . . 17
Moving to another CHAPTER . . . . . . . . . . . 17
Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Still Picture and Frame-by-Frame Playback . 17
Slow Motion. . . . . . . . . . . . . . . . . . . . . . . . . 17
Random . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Repeat A-B . . . . . . . . . . . . . . . . . . . . . . . . . 18
Repeat . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Time Search . . . . . . . . . . . . . . . . . . . . . . . . 18
3D Surround . . . . . . . . . . . . . . . . . . . . . . . . 18
Zoom. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Marker Search . . . . . . . . . . . . . . . . . . . . . . . 18
Special DVD Features . . . . . . . . . . . . . . . . . . . . 19
Title Menu . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Disc Menu . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Camera Angle . . . . . . . . . . . . . . . . . . . . . . . 19
Changing the Audio Language . . . . . . . . . . . 19
Subtitles . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Video Mode Setting . . . . . . . . . . . . . . . . . . . . . . 19
Screen Saver . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4
Audio CD and MP3/WMA Operation . . . . . . . . 20-21
Playing an Audio CD or MP3/WMA Disc . . . . . . 20
Notes on MP3/WMA Recordings . . . . . . . . . . . . 20
Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Changing Tracks . . . . . . . . . . . . . . . . . . . . . 21
Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Random with MP3/WMA Disc . . . . . . . . . . . 21
Random Track/ All/ Off . . . . . . . . . . . . . . . . . 21
Random with Audio CD . . . . . . . . . . . . . . . . 21
Repeat A-B . . . . . . . . . . . . . . . . . . . . . . . . . 21
3D Surround . . . . . . . . . . . . . . . . . . . . . . . . 21
Changing Audio Channels . . . . . . . . . . . . . . 21
Repeat Track/ Disc/ All/ Off . . . . . . . . . . . . . 21
JPEG Files Operation . . . . . . . . . . . . . . . . . . . . . . 22
Viewing JPEG Files . . . . . . . . . . . . . . . . . . . . . . 22
Changing Files . . . . . . . . . . . . . . . . . . . . . . 22
Still Picture . . . . . . . . . . . . . . . . . . . . . . . . . 22
To flip the picture . . . . . . . . . . . . . . . . . . . . . 22
To rotate the picture . . . . . . . . . . . . . . . . . . . 22
Notes on JPEG Files . . . . . . . . . . . . . . . . . . 22
Programmed Playback . . . . . . . . . . . . . . . . . . . . . 23
Programmed Playback with Audio CD . . . . . . . . 23
Programmed Playback with MP3/WMA Discs . . 23
Repeat Programmed Tracks . . . . . . . . . . . . . 23
Erasing a Track from the Program List . . . . . 23
Erasing the Complete Program List . . . . . . . 23
Reference
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Language Code List . . . . . . . . . . . . . . . . . . . . . . . 25
Country Code List . . . . . . . . . . . . . . . . . . . . . . . . . 26
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
About the symbols for instructions
Indicates hazards likely to cause harm to the unit
itself or other material damage.
Indicates special operating features of this unit.
Indicates tips and hints for making the task easier.
Before Use
Playable Discs
Title (DVD only)
The main film content, accompanying feature content,
additional feature content, or music album.
Each title is assigned a title reference number enabling
you to locate it easily.
DVD
(8 cm / 12 cm disc)
Audio CD
(8 cm / 12 cm disc)
In addition, this unit can play : DVD-R, DVD±RW, CD-R,
or CD-RW discs that contain audio titles, MP3, WMA, or
JPEG files.
otes
– Depending on the condition of the recording equipment or the CD-R/RW (or DVD-R/±RW) disc itself,
some CD-R/RW (or DVD-R/±RW) discs cannot be
played on the unit.
– Do not attach any seal or label to either side (the
labeled side or the recorded side) of a disc.
– Do not use irregularly shaped CDs (e.g., heart-shaped
or octagonal). The unit may malfunction.
Chapter (DVD only)
Sections of a picture or a musical piece that are smaller
than titles. A title is composed of one or several chapters. Each chapter is assigned a chapter number,
enabling you to locate the chapter you want. Depending
on the disc, chapters may not be recorded.
Track (Audio CD only)
Sections of a musical piece on an audio CD. Each track
is assigned a track number, enabling you to locate the
track you want.
otes on DVDs
Some playback operations of DVDs may be intentionally
fixed by software manufacturers. As this unit plays DVDs
according to disc content designed by the software
manufacturer, some playback features of the unit may
not be available or other functions may be added.
Refer also to the instructions supplied with the DVDs.
Some DVDs made for business purposes may not be
played on the unit.
Regional code of the DVD player and DVDs
This DVD player is designed and manufactured
for playback of region “1” encoded DVD software.
The region code on the labels of some DVD discs indicate which type of player can play those discs. This unit
can play only DVD discs labeled “1” or “ALL”. If you try to
play any other discs, the message “Check Regional
Code” will appear on the TV screen. Some DVD discs
may not have a region code label even though their playback is prohibited by area limits.
1
5
INTRODUCTION
Disc-related terms
Before Use (Continued)
Precautions
Handling the unit
When shipping the unit
The original shipping carton and packing materials
come in handy. For maximum protection, re-pack the
unit as it was originally packed at the factory.
When setting up the unit
The picture and sound of a nearby TV, VCR, or radio
may be distorted during playback. In this case, position
the unit away from the TV, VCR, or radio, or turn off the
unit after removing the disc.
To keep the exterior surfaces clean
Do not use volatile liquids, such as insecticide spray,
near the unit. Do not leave rubber or plastic products in
contact with the unit for a long period of time. They will
leave marks on the surface.
Storing discs
After playing, store the disc in its case.
Do not expose the disc to direct sunlight or sources of
heat, or leave it in a parked car exposed to direct sunlight, as there may be a considerable temperature
increase inside the car.
Cleaning discs
Fingerprints and dust on the disc can cause poor picture quality and sound distortion. Before playing, clean
the disc with a clean cloth. Wipe the disc from the center out.
Yes
No
Cleaning the unit
To clean the cabinet
Use a soft, dry cloth. If the surfaces are extremely dirty,
use a soft cloth lightly moistened with a mild detergent
solution. Do not use strong solvents such as alcohol,
benzine, or thinner, as these might damage the surface
of the unit.
To obtain a clear picture
The DVD player is a high-tech, precision device. If the
optical pick-up lens and disc drive parts are dirty or
worn, the picture quality will be poor.
Regular inspection and maintenance are recommended
after every 1,000 hours of use. (This depends on the
operating environment.)
For details, please contact your nearest dealer.
Notes on Discs
Handling discs
Do not touch the playback side of the disc.
Hold the disc by the edges so that fingerprints will not
get on the surface.
Do not stick paper or tape on the disc.
6
Do not use strong solvents such as alcohol, benzine,
thinner, commercially available cleaners, or anti-static
spray intended for older vinyl records.
About Symbols
About the
symbol display
“
” may appear on the TV screen during operation.
This icon means the function explained in this owner’s
manual is not available on that specific DVD video disc.
About the disc symbols for instructions
Section in this manual whose title has one of the
following symbols is applicable only to the disc(s)
represented by the symbol.
DVD DVD
CD
Audio CD.
MP3 MP3 disc.
WMA WMA disc.
JPEG JPEG Files on Disc.
Front Panel and Display Window
POWER
Switches the player ON and OFF.
OPEN/CLOSE ( / )
Opens or closes the disc tray.
INTRODUCTION
STOP ( 9 )
Stops playback.
STANDBY indicator
Lights red when the player is in Standby mode (off).
Remote Sensor
Point the DVD Player remote control here.
Display window
Shows the current status of the player.
Disc Tray
Insert a disc here.
DISC SKIP
Moves to the next available disc tray.
DISC EXCHANGE
Allows you to change a disc
(other than the one playing) during
playback
PLAY ( 2 )
Starts playback.
PAUSE ( ; )
Pauses playback temporarily /
press repeatedly for frame-by-frame playback.
Reverse SKIP/SCAN ( Q / S )
Go to beginning of current chapter/track or to PREVIOUS chapter/track.
Press and hold for two seconds for a fast reverse search.
Forward SKIP/SCAN ( T / R )
Go to NEXT chapter/track.
Press and hold for two seconds for a fast forward search.
ANGLE Lights when multi angles are
present.
TITLE Indicates current title number
CHP/TRK Indicates current chapter or track number
A light will appear if a disc is in the
disc tray. The current disc tray flashes.
Indicates total playing time/elapsed time
PROG. Programmed playback active
DVD inserted
CD Audio CD inserted
MP3 MP3 or WMA disc
inserted
DVD
RANDOM RANDOM
playback active
Indicates repeat
mode
Indicates current player function:
Playback, Pause, etc.
MP3
CD DVD
1
2
3
TITLE
CHP/TRK
PROG.
RANDOM ALL A
B
5
4
7
Remote Control
POWER
Switches DVD Player ON and OFF.
OPEN/CLOSE
Opens and closes the disc tray.
DISPLAY
Accesses On-Screen display.
SELECT/ENTER
Acknowledges menu selection.
b B v V (left/right/up/down)
Selects options in a menu.
MENU
Accesses menu on a DVD disc.
PAUSE/STEP ( X ) •
Pauses playback temporarily/ press
repeatedly for frame-by-frame
playback.
Reverse SLOW ( t ) •
Reverse slow playback.
power
open / close
display
select
title
skip / scan
play
• PLAY (H )
Starts playback.
skip / scan
• Reverse SKIP/SCAN ( . )
Search backward*/ go to beginning
of current chapter or track or go to
previous chapter or track.
program
STOP ( x ) •
Stops playback.
AUDIO •
Selects an audio language (DVD) or
an audio channel (CD).
• Forward SKIP/SCAN ( > )
Search forward*/ go to next chapter
or track.
enter
Forward SLOW ( T ) •
Forward slow playback.
0-9 number buttons
Select numbered options in a menu.
TITLE
Displays the disc’s Title menu, if
available.
return
menu
RETURN
Removes the Setup menu.
clear
* Press and hold button for about
two seconds.
audio subtitle
repeat
a-b
setup
PROGRAM
Enters/exits the program edit mode.
random zoom
CLEAR
Removes a track number on the
program list or a mark on the
MARKER SEARCH menu.
marker search disc skip
SUBTITLE •
Selects a subtitle language.
ANGLE •
Selects a DVD camera angle if
available
• REPEAT
Repeat chapter, track, group, title, all.
• A-B
Repeat sequence.
SETUP •
Accesses or removes setup menu.
• RANDOM
Plays tracks in random order.
MARKER •
Marks any point during playback.
• ZOOM
Enlarges video image.
SEARCH •
Displays MARKER SEARCH menu.
DISC SKIP •
Moves to the next available disc
tray.
8
AAA
Point the remote control at the remote sensor and press
the buttons.
Distance: About 23 ft (7 m) from the front of the
remote sensor.
Angle: About 30° in each direction of the front of the
remote sensor.
Remote Control Battery Installation
AAA
Remote Control Operating Range
Detach the battery cover on the rear of
the remote control, and insert two R03
(size AAA) batteries with
and
aligned correctly. Replace cover.
Caution
Do not mix old and new batteries. Never mix different
types of batteries (standard, alkaline, etc.).
DVD Connections Panel
INTRODUCTION
COAXIAL (Digital audio out jack)
Connect to digital (coaxial) audio equipment.
ANALOG AUDIO OUT (Left/Right) 1, 2
Connect to an amplifier, receiver or stereo system.
VIDEO OUT
Connect to a TV with video inputs.
COMPONENT/PROGRESSIVE SCAN
VIDEO OUT (Y Pb Pr)
Connect to a TV with Y Pb Pr inputs.
S-VIDEO OUT
Connect to a TV with S-Video inputs.
AC Power Cord
Plug into the power source.
Do not touch the inner pins of the jacks on the DVD
connections panel. Electrostatic discharge may
cause permanent damage to the unit.
9
Connections
ips
Depending on your TV and other equipment you wish
to connect, there are various ways you could connect
the player. Use only one of the connections
described below.
Please refer to the manuals of your TV, VCR, Stereo
System or other devices as necessary to make the
best connections.
For better sound reproduction, connect the player’s
AUDIO OUT jacks to the audio in jacks of your
amplifier, receiver, stereo or audio/video equipment.
See “Optional Equipment Connections” on page 11.
Caution
– Make sure the DVD Player is connected directly to the
TV. Tune the TV to the correct video input channel.
– Do not connect the DVD Player’s AUDIO OUT jack to
the phono in jack (record deck) of your audio system.
– Do not connect your DVD Player via your VCR. The
DVD image could be distorted by the copy protection
system.
Connecting to a TV
Make one of the following connections, depending on
the capabilities of your existing equipment.
Progressive Scan (Color Stream® pro) connection
1
If your television is high-definition or “digital ready”,
you may take advantage of the DVD Player’s progressive scan output for the highest video resolution
possible.
If your TV does not accept the Progressive Scan format, the picture will appear scrambled if you use the
DVD’s Progressive Scan output.
Connect the COMPONENT VIDEO OUT/
PROGRESSIVE SCAN jacks on the DVD Player to
the corresponding in jacks on the TV using an
optional Y Pb Pr cable (C).
the DVD Player’s Left and Right AUDIO
2 Connect
OUT jacks to the audio left/right in jacks on the TV
using the supplied audio cables (A).
otes
– Set Progressive Scan to “On” in the Setup menu to
use a progressive signal, see page 13.
– Progressive scan does not work with the analog video
connections (yellow VIDEO OUT jack).
Rear of TV
Video connection
1
S-VIDEO
INPUT
Connect the VIDEO OUT jack on the DVD Player to
the video in jack on the TV using the supplied video
cable (V).
COMPONENT VIDEO
Pr
Pb
VIDEO
INPUT
AUDIO INPUT
Y
L
R
L
the DVD Player’s Left and Right AUDIO
2 Connect
OUT jacks to the audio left/right in jacks on the TV
using the supplied audio cables (A).
S-Video connection
1
S
C
A
Connect the S-VIDEO OUT jack on the DVD Player
to the S-Video in jack on the TV using the supplied
S-Video cable (S).
the DVD Player’s Left and Right AUDIO
2 Connect
OUT jacks to the audio left/right in jacks on the TV
using the supplied audio cables (A).
Component Video (Color Stream®) connection
1
Connect the COMPONENT VIDEO OUT/
PROGRESSIVE SCAN jacks on the DVD Player to
the corresponding in jacks on the TV with optional Y
Pb Pr cables (C).
the DVD Player’s Left and Right AUDIO
2 Connect
OUT jacks to the audio left/right in jacks on the TV
using the supplied audio cables (A).
10
DVD player Connections Panel
V
Connections (Continued)
Optional Equipment Connections
DVD player Connections Panel
INTRODUCTION
Connecting to an amplifier equipped with
2-Channel analog stereo or Dolby Pro Logic ll/
Pro Logic
Connect the Left and Right AUDIO OUT jacks on the
DVD Player to the audio left and right in jacks on your
amplifier, receiver, or stereo system, using the audio
cables (A).
Connecting to an amplifier equipped with
2-Channel digital stereo (PCM) or to an Audio/
Video receiver equipped with a multi-channel
decoder (Dolby Digital™, MPEG 2, or DTS)
1
Connect one of the DVD Player’s DIGITAL AUDIO
OUT jacks (COAXIAL X) to the corresponding in
jack on your amplifier. Use an optional digital
(coaxial X) audio cable.
2
You will need to activate the player’s digital output.
(See “Digital Audio Output” on page 14).
X
COAXIAL
DIGITAL INPUT
A
L
R
AUDIO INPUT
Amplifier (Receiver)
Digital Multi-channel sound
A digital multi-channel connection provides the best
sound quality. For this you need a multi-channel
Audio/Video receiver that supports one or more of the
audio formats supported by your DVD Player (MPEG 2,
Dolby Digital and DTS). Check the receiver manual and
the logos on the front of the receiver.
Caution:
Due to the DTS Licensing agreement, the digital output
will be in DTS digital out when DTS audio stream is
selected.
otes
– If the audio format of the digital output does not match
the capabilities of your receiver, the receiver will
produce a strong, distorted sound or no sound at all.
– Six Channel Digital Surround Sound via digital connection can only be obtained if your receiver is
equipped with a Digital Multi-channel decoder.
– To see the audio format of the current DVD in the onscreen display, press AUDIO.
11
Pre-operation
General Explanation
Playback Status/Restrictions
This manual gives basic instructions for operating the
DVD Player. Some DVDs require specific operation or
allow only limited operation during playback. When this
occurs, the symbol
appears on the TV screen, indicating that the operation is not permitted by the DVD
Player or is not available on the disc.
TITLE
CHAPT
Repeat Title
Repeat Chapter
A B
Repeat A-B
OFF
Repeat Off
Resume play from this point
Action prohibited or not available
On-Screen Display
General playback status can be displayed on the TV
screen. Some options can be changed on the menu.
On-screen display operation
1 Press DISPLAY during playback.
3/4
4 to select a menu option.
2 Use
The selected option will be highlighted.
1/2
2 to change the setting of a menu option.
3 Use
The number buttons can be also be used for setting
otes
Some discs may not provide all of the features on the
on-screen display example shown below.
If no button is pressed for 10 seconds, the on-screen
display disappears.
numbers (e.g., title number). For some functions,
press SELECT/ENTER to execute the setting.
DVD
4 to select desired options)
Function (Use 3/4
Selection Method
1 /3
Shows the current title number and total number of
titles, and skips to the desired title number.
1 / 2, or
Numbers, SELECT/ENTER
1 /12
Shows the current chapter number and total number of
chapters, and skips to the desired chapter number.
1 / 2, or
Numbers, SELECT/ENTER
Shows the elapsed playing time, and
searches the point by the elapsed time directly.
Numbers, SELECT/ENTER
Menu Options
Title Number
Chapter Number
Time search
0:20:09
Audio language
and Digital Audio
Output mode
Subtitle language
1 ENG
D
5.1 CH
ABC
Angle
Sound
12
OFF
1 /1
NORM.
Shows the current audio soundtrack language,
encoding method, and channel number, and
changes the setting.
Shows the current subtitles language, and
changes the setting.
Shows the current angle number and total number of
angles, and changes the angle number.
Shows the current sound mode, and
changes the setting.
1 / 2, or
AUDIO
1 / 2, or
SUBTITLE
1 / 2, or
ANGLE
1 /2
Pre-operation (Continued)
Picture
You can set your own personal preferences on the DVD
player.
TV Aspect
Pre-operation Setup
1
Press SETUP.
The Setup menu appears.
DVD
4:3 Letterbox: Select when a standard 4:3 TV is connected. Displays theatrical images with masking bars
above and below the picture.
4:3 Panscan: Select when a conventional TV set is
connected. The video material formatted in the Pan &
Scan style is played back in that style (Both sides of the
picture are cut off).
16:9 Wide: Select when a 16:9 wide TV is connected.
Disc Audio
Original
Disc Subtitle
English
Disc Menu
French
Rating
German
Disc Audio
4:3 Letterbox
Country Code
Spanish
Disc Subtitle
4:3 Panscan
TV Aspect
Italian
Disc Menu
16:9 Wide
Menu Language
Chinese
Rating
Progressive Scan
Polish
Country Code
Digital Audio Output
Hungarian
5.1 Speaker Setup
Other – – – –
Others
TV Aspect
Menu Language
Progressive Scan
Digital Audio Output
2
4 to select the desired option.
Use 3/4
The screen will show the current setting for the
selected option, as well as alternate setting(s).
While the desired option is selected, press 2,
4 to select the desired setting.
then 3/4
Press SELECT/ENTER to confirm your selection.
Some options require additional steps.
3
4
SETUP, RETURN, or PLAY to exit and
5 Press
remove the Setup menu.
Language
Disc Language
DVD
Select a language for the disc’s Menu, Audio, and
Subtitle.
Original: The original language set for the disc is selected.
Other: To select another language, use number buttons to
enter the corresponding 4-digit number according to the language code list on page 25. If you enter the wrong language
code, press CLEAR.
5.1 Speaker Setup
Others
Progressive Scan
DVD
Progressive Scan Video provides the highest quality picture with less flickering.
• If you are using the COMPONENT VIDEO OUT/
PROGRESSIVE SCAN jacks, but are connecting the
DVD Player to a standard (analog) television, set
Progressive Scan to Off.
• If you are using the Component Video jacks for
connection to a TV or monitor that is compatible with
a progressive scan signal, set Progressive Scan to
On.
Disc Audio
Off
Disc Subtitle
On
Disc Menu
Rating
Country Code
TV Aspect
Menu Language
Progressive Scan
Disc Audio
Original
Disc Subtitle
English
Disc Menu
French
Rating
German
Country Code
Spanish
TV Aspect
Italian
Menu Language
Chinese
Progressive Scan
Polish
Digital Audio Output
Hungarian
5.1 Speaker Setup
Other – – – –
Others
Menu Language
Select a language for the Setup menu. This is the menu
you see when you press SETUP.
Disc Audio
English
Disc Subtitle
Spanish
Disc Menu
French
Digital Audio Output
5.1 Speaker Setup
Others
Caution
Once the setting for progressive scan output is entered, an
image will only be visible on a progressive scan compatible TV
or monitor. If you set Progressive Scan to On in error, you
must reset the unit. Press STOP to stop any disc that is playing. Next, press STOP again and hold it for five seconds
before releasing it. The video output will be restored to the
standard setting, and a picture will once again be visible on a
conventional analog TV or monitor.
Rating
Country Code
TV Aspect
Menu Language
13
PRE-OPERATION
Pre-operation Settings
Pre-operation (Continued)
Sound
Others
Digital Audio Output
DRC, Vocal, and Auto Play settings can be changed.
4 to select the desired option and press
Use 3/4
SELECT/ENTER. The setting of the selected option
can be turned On or Off.
Each DVD disc has a variety of audio output options.
Set the player’s Digital Audio Output according to the
type of audio system you use.
DOLBY DIGITAL/PCM: Select “DOLBY DIGITAL/PCM”
if you connect the DVD Player’s DIGITAL OUT jack to a
Dolby Digital decoder (or an amplifier or other equipment with a Dolby Digital decoder).
Stream/PCM: Select “Stream/PCM” if you connect the
DVD Player’s DIGITAL OUT jack to an amplifier or other
equipment with a DTS decoder, Dolby Digital decoder
or MPEG decoder.
PCM: Select “PCM” if you connect to a 2-channel digital
stereo amplifier. The DVD player outputs sounds in the
PCM 2ch format; when you play a DVD video disc
recorded on the Dolby Digital, MPEG1, or MPEG2
recording system.
Disc Audio
DOLBY
DIGITAL
Disc Subtitle
Stream/PCM
Disc Menu
PCM
/PCM
Rating
Country Code
TV Aspect
Menu Language
Progressive Scan
Sample Freq.
48 KHz
96KHz
Digital Audio Output
5.1 Speaker Setup
Others
Sample Frequency
To change the Sample Frequency setting, first select the
desired Digital Audio Output as indicated as above.
If your receiver or amplifier is NOT capable of handling
96KHz signals, select 48KHz. When this choice is
made, this unit will automatically convert any 96KHz signals to 48KHz so your system can decode them.
If your receiver or amplifier is capable of handling
96KHz signals, select 96KHz. When this choice is
made, this unit will pass each type of signal through
without any further processing.
Disc Audio
DRC
On
Disc Subtitle
Vocal
On
Disc Menu
Auto Play
Off
Rating
Country Code
TV Aspect
Menu Language
Progressive Scan
Digital Audio Output
5.1 Speaker Setup
Others
Dynamic Range Control (DRC)
With the DVD format, you can hear a program’s soundtrack in the most accurate and realistic presentation
possible, thanks to digital audio technology. However,
you may wish to compress the dynamic range of the
audio output (the difference between the loudest sounds
and the quietest ones). Then, you may listen to a movie
at a lower volume without losing clarity of sound. Set
DRC to On for this effect.
Vocal
Set Vocal to On only when a multi-channel karaoke DVD
is playing. The karaoke channels on the disc will mix
into normal stereo sound.
Auto Play
DVD
You can set up the DVD Player so a DVD disc automatically starts playing whenever the DVD is inserted.
If Auto Play mode is set to On, this DVD player will
search for title that has the longest playback time and
then play back the title automatically.
On: Auto Play function is active.
Off: Auto Play function is not active.
ote
The Auto Play function may not work for some DVDs.
14
Pre-operation (Continued)
Parental Control
Country Code
Rating
Enter the code of a country/area whose standards were
used to rate the DVD video disc, referring to the list
(See “Country Code List”, page 26.).
Movies on DVDs may contain scenes not suitable for
children. Therefore, discs may contain Parental Control
information that applies to the complete disc or to
certain scenes on the disc. These scenes are rated from
1 to 8, and alternatively, more suitable scenes are available for selection on some discs. Ratings are
country-dependent. The Parental Control feature allows
you to prevent discs from being played by your children
or to have certain discs played with alternative scenes.
Disc Audio
Disc Subtitle
Code Set
U S
Disc Menu
Rating
Country Code
TV Aspect
Menu Language
Progressive Scan
Digital Audio Output
5.1 Speaker Setup
Disc Audio
8
Disc Subtitle
7
Disc Menu
6
Rating
Country Code
5
TV Aspect
Menu Language
3
Progressive Scan
1
Digital Audio Output
Unlock
5.1 Speaker Setup
Change
4
2
Others
“Rating” on the Setup menu using the
1 Select
3/4
4 buttons.
2 While “Rating” is selected, press 2.
you have not entered a password yet.
3 When
Enter a 4-digit password using the numbered buttons and create a personal 4-digit security password, then press SELECT/ENTER. Enter the 4-digit
password again and press SELECT/ENTER to verify.
When you have already entered a password;
Enter a 4-digit password using the numbered buttons to confirm the personal 4-digit security password, then press SELECT/ENTER.
If you make a mistake before pressing SELECT/ENTER,
press CLEAR and enter 4-digit security password again.
4 butSelect a rating from 1 to 8 using the 3/4
4 tons.
One (1) has the least playback restrictions.
Eight (8) has the most playback restrictions.
Unlock: If you select Unlock, Parental Control is not
active. The entire disc will play in full.
Ratings 1 to 8: Some discs contain scenes not
suitable for children. If you set a rating for the player, all disc scenes with the same rating or lower will
be played. Higher rated scenes will not be played
unless an alternative scene is available on the disc.
The alternative must have the same rating or a
lower one. If no suitable alternative is found, playback will stop. You must enter the 4-digit password
or change the rating level in order to play the disc.
5
Press SELECT/ENTER to confirm your rating
selection, then press SETUP to exit the menu.
Others
Country Code on the Setup menu using
1 Select
4 buttons.
the 3/4
2 While Country Code is selected, press 2.
3 Follow step 3 of “Rating” on left.
4 Select the first character using the 3/44 buttons.
the cursor using 2 button and select the
5 Shift
4 buttons.
second character using 3/4
Press SELECT/ENTER to confirm your country
6 code
selection, then press SETUP to exit the
menu.
ote
Confirmation of the 4-digit password is necessary when
the code is changed (see “Changing the 4-digit code”
below.).
Changing the 4-digit code
1 Follow Steps 1-2 as shown above to the left (Rating).
2 Enter the old code, then press SELECT/ENTER.
4 buttons then press
3 Select Change using 3/4
SELECT/ENTER.
4 Enter the new 4-digit code, then press
SELECT/ENTER.
5 Enter exactly the same code a second time and verify by pressing SELECT/ENTER.
6 Press SETUP to exit the menu.
If you forget your 4-digit password
If you forgot your password, to clear the current password, follow the procedure below.
1 Press SETUP to display the Setup menu.
2 Use the Number buttons to enter the 6-digit number
“210499”.
The 4-digit password is cleared. “P CLr” appears on the
display for a moment.
3 Enter a new password as shown above to the left
(Rating).
15
PRE-OPERATION
DVD
DVD
DVD Operation
Playing a DVD
Exchanging discs during playback
Playback Setup
DVD
Turn on the TV and select the video input source connected to the DVD player.
Audio system: Turn on the audio system and select
the input source connected to the DVD player.
Press OPEN/CLOSE to open the disc tray.
1
your chosen disc in the tray, with the
2 Load
playback side down.
Do not load a disc in the
left or right side position.
Center Position
Tray
• Discs can be loaded one at-a-time. Press
DISC SKIP to rotate the carousel.
OPEN/CLOSE to close the tray.
3 Press
READING appears on the TV screen, and playback
starts automatically. If playback does not start,
press PLAY.
In some cases, the disc menu might appear
instead.
If a menu screen is displayed
A menu screen may be displayed first after loading a
DVD with menus.
DVD
Use the 1 234 buttons to select the title/chapter you
want to view, then press SELECT/ENTER to start playback.
Press TITLE or MENU to return to the menu screen.
otes
– If Parental Control is set and the disc is not within the
Rating settings (not authorized), the 4-digit code must
be entered and/or the disc must be authorized (see
“Parental Control”, on page 15).
– DVDs may have a Region Code.
Your player will not play discs that have a Region
Code different from your player. The region code for
this player is 1 (one).
16
Press DISC EXCHANGE on the front panel during
playback to open the disc tray.
Press DISC SKIP to rotate the disc tray. The carousel
will rotate clockwise one disc at-a-time.
Exchange the discs and press DISC EXCHANGE or
OPEN/CLOSE to close the disc tray.
ote
– The disc tray presently loaded in the play position can
not be exchanged.
Skipping discs
Press DISC SKIP during playback or in Stop mode.
otes
– When DISC SKIP is pressed, the disc tray rotates and
playback begins from the beginning of the next disc.
– If there is no disc on the next disc tray, the following
disc tray will be selected.
– When DISC SKIP is pressed during playback of disc
5, playback of disc 1 will start.
Exchanging the disc and starting playback
1. Press OPEN/CLOSE during playback or in Stop
mode.
Play stops (if pressed during playback), the disc tray opens
and the disc that was in the play position comes to the front.
2. Exchange the disc.
3. Press OPEN/CLOSE or PLAY again.
The tray closes and playback begins (with the disc
that is in front).
DVD Operation (Continued)
General Features
Still Picture and Frame-by-Frame Playback
ote
Unless stated otherwise, all operations described use
the remote control. Some features may also be
available on the Setup menu.
1. Press PAUSE/STEP during playback.
The player will go into PAUSE mode.
2. You can advance the picture frame-by-frame by pressing PAUSE/STEP repeatedly on the remote control.
Changing TITLEs
Slow Motion
DVD
DVD
1. Press SLOW t or T during playback.
1 /3
The DVD player will enter SLOW mode.
When a disc has more than one title, you can move to
another title as follows:
Press DISPLAY then use the appropriate numbered
button (0-9) to select a title number.
Changing CHAPTERs
DVD
1 /12
If a title on a disc has more than one chapter, you can
move to another chapter as follows:
Press SKIP/SCAN . or > briefly during
playback to select the next chapter or to return to the
beginning of the current chapter.
Press . twice briefly to step back to the previous
chapter.
To go directly to any chapter during DVD playback,
4 to select the chapter
press DISPLAY. Then, use 3/4
icon. Then, enter the chapter number using the numbered buttons (0-9).
ote
Press two-digit numbered buttons (0-9) in rapid
succession. For example, press 0, 2 instead of pressing
only 2.
Search
2. Use the SLOW t or T to select the required speed:
t 1/16, t 1/8, t 1/4 or t 1/2 (backward), or
T 1/16, T 1/8, T 1/4 or T 1/2 (forward).
3. To exit slow motion mode, press PLAY.
Random
Karaoke DVD
1 Press RANDOM during playback or when playback is
stopped.
The unit automatically begins Random Playback and
RANDOM or “RAND.” appears on the display window
and menu screen.
2 To return to normal playback, press RANDOM repeatedly until RANDOM or “RAND.” disappears on the display window and menu screen.
ip
By pressing SKIP/SCAN > during Random playback,
the unit selects another title and resumes Random playback.
ote
This function only works with DVD Karaoke discs.
DVD
1. Press and hold SKIP/SCAN . or > for about
two seconds during playback.
The player will now go into SEARCH mode.
2. Press and hold SKIP/SCAN . or > repeatedly
to select the required speed: mX2, mX4, mX16,
mX100 (backward) or MX2, MX4, MX16,
MX100 (forward).
3. To exit SEARCH mode, press PLAY.
17
OPERATION
DVD
DVD Operation (Continued)
Repeat A-B
A *
A B
General Features (Continued)
DVD
OFF
Zoom
To repeat a sequence in a title:
The Zoom function allows you to enlarge the video
image and to move through the enlarged image.
1. Press A-B at your chosen start point.
“ A * ” appears briefly on the TV screen.
2. Press A-B again at your chosen end point.
“A B” appears briefly on the TV screen, and the repeat
sequence begins (“AsB” appears the display window).
3. To cancel the sequence, press A-B.
Repeat
DVD
CHAPT
TITLE
DVD
1. Press ZOOM during playback or still playback to activate the Zoom function.
If you press ZOOM repeatedly, the magnification level
increases up to six steps.
2. Use the 1 234 buttons to move through the zoomed
picture.
ALL
OFF
DVD Video Discs - Repeat Chapter/Title/All/Off
3. Press CLEAR to resume normal playback or return to
the paused image.
1. To repeat the chapter currently playing, press REPEAT.
The Repeat Chapter icon appears on the TV screen.
2. To repeat the title currently playing, press REPEAT a
second time.
The Repeat Title icon appears on the TV screen.
3. To repeat entire all disc contents, press REPEAT a
third time.
ote
The zoom function may not work for some DVDs.
Marker Search
1/9
DVD
MARKER SEARCH
The Repeat All icon appears on the TV screen.
4. To exit Repeat mode, press REPEAT a fourth time.
The Repeat Off icon appears on the TV screen.
Time Search
DVD
0:20:09
-:--:--
The Time Search function allows you to start playing at
any chosen time on the disc.
1. Press DISPLAY during playback. The on-screen display appears on the screen.
The Time Search box shows the elapsed playing time of the
current disc.
4 to select the Time
2. Within 10 seconds, use 3/4
Search icon on the on-screen display.
The “-:--:--” appears in the Time Search box.
3. Within 10 seconds, use the number buttons to enter
the required start time. Enter hours, minutes, and
seconds from left to right in the box.
If you enter the wrong numbers, press CLEAR to remove the
numbers you entered. Then enter the correct numbers.
4. Within 10 seconds, press SELECT/ENTER to confirm
the start time.
Playback starts from the selected time on the disc. If you enter
an invalid time, playback will continue from the current point.
You can start playback from a memorized point. Up to
nine Marker points can be memorized.
To enter a marker point, follow these steps.
1. During disc playback, press MARKER when
playback reaches the spot that you want to
memorize.
The Marker icon will appear on the TV screen briefly.
2. Repeat step 1 to enter up to nine Marker points on a
disc.
To Recall a Marked Scene
1. During disc playback, press SEARCH.
The MARKER SEARCH menu will appear on the screen.
2. Within 10 seconds, use 1/2 to select a Marker
number that you want to recall.
3. Press SELECT/ENTER.
Playback will start from the Marked scene.
4. To remove the MARKER SEARCH menu, press
SEARCH.
To Clear a Marked Scene
1. During disc playback, press SEARCH.
3D Surround
DVD
NORM.
3D SUR
This DVD player can produce a 3D Surround effect,
which simulates multi-channel audio playback from two
conventional stereo speakers, instead of the five or
more speakers normally required to listen to multichannel audio from a home theater system.
1. Press DISPLAY during playback.
2. Use 3 or 4 to select the sound option.
The sound option will be highlighted.
3. Use 1 or 2 to to select “3D SUR”.
To turn off the 3D Surround effect, select “NORM”.
18
The MARKER SEARCH menu will appear on the screen.
2. Use 1/2 to select the Marker number that you want
to erase.
3. Press CLEAR.
The Marker number will be erased from the list.
4. Repeat steps 2 and 3 to erase additional Marker
numbers.
5. To remove the MARKER SEARCH menu, press
SEARCH.
DVD Operation (Continued)
Video Mode Setting
DVD
With certain discs, the playback picture may be flickering or Dot Crawl is shown on straight lines. That
means Vertical interpolation or De-interlace is not
perfectly matched with the disc. In this case, the
picture quality may be improved by changing the
video mode.
To change the video mode, press and hold
DISPLAY about 3 seconds during disc playback. The
new video mode number selected is displayed on the
TV screen. Check whether the video quality has
improved. If not, repeat the above procedure until picture quality is improved.
Video mode sequence:
MODE1 → MODE2 → MODE3 → MODE1
If you turn off the power, the video mode will return to
initial default state (MODE1).
Checking the Contents of DVD Video
Discs: Menus
DVDs may offer menus that allow you to access special
features. To use the disc menu, press MENU. Then, use
the appropriate number button to select an option. Or,
use the 1 234 buttons to highlight your selection, then
press SELECT/ENTER.
Title Menu
DVD
1. Press TITLE.
If the current title has a menu, the menu will appear on the
screen. Otherwise, a disc menu may appear.
2. The menu can list camera angles, spoken language,
subtitle options, and chapters for the title.
3. To remove the title menu, press TITLE again.
Disc Menu
Detailed Descriptions for Video Modes
MODE1: The source material of the DVD video (film material or
video material) is determined from disc information.
DVD
1. Press MENU.
The disc menu is displayed.
2. To remove the disc menu, press MENU again.
Camera Angle
DVD
DVD
1 /1
If the disc contains scenes recorded at different camera
angles, you can change to a different camera angle
during playback.
Press ANGLE repeatedly during playback to select a
desired angle.
The number of the current angle appears on the display.
Changing the Audio Language
DVD
MODE2: Suitable for playing film based content or video based
material recorded by the progressive scan method.
MODE3: Suitable for playing video based content with comparatively little motion.
ote
The video mode setting only works when the Progressive
Scan mode is set to “On” in the Setup menu.
Screen Saver
The screen saver appears if you leave the DVD Player
in Stop mode for about five minutes.
After the Screen Saver has been engaged for about five
minutes, the DVD Player will automatically turn itself off.
1 ENG
D
5.1 CH
Press AUDIO repeatedly during playback to hear a different audio language or audio track.
Subtitles
DVD
ABC
1 ENG
Press SUBTITLE repeatedly during playback to see the
different subtitle languages available.
If
ote
appears, the feature is not available on the disc.
19
OPERATION
Special DVD Features
Audio CD and MP3/WMA Operation
Playing an Audio CD or MP3/WMA
Disc CD MP3 WMA
The DVD Player can play audio CDs. Also, the DVD
Player can play MP3/WMA formatted recordings on
CD-ROM, CD-R, or CD-RW discs.
Before playing MP3/WMA recordings, read the notes on
MP3/WMA Recordings on right.
Insert a disc and close the tray.
Audio CD; Audio CD menu appears on the TV
screen go to step 4.
MP3/WMA disc; The MP3/WMA-JPEG choice
menu appears on the TV screen. Go to step 2
1
MP3 WMA
3/4
4 to select the MP3/WMA then press
2 Use
SELECT/ENTER.
The MP3/WMA menu appears on the TV screen.
Press RETURN to move to the MP3/WMA-JPEG
choice menu.
TRACK
TRACK
TRACK
TRACK
TRACK
TRACK
TRACK
TRACK
2
Program
1.mp3
2.mp3
3.mp3
4.mp3
5.mp3
6.mp3
7.mp3
8.mp3
00:00
Clear All
OFF
1
3/4
4 to select a folder, and SELECT/ENTER.
3 Use
A list of files in the folder appears.
3/4
4 to select a track then press PLAY or
4 Use
SELECT/ENTER.
Playback starts.
During playback, the current track’s elapsed playing
time will appear on the display window and menu.
Playback will stop at the end of the disc.
Press TITLE to move to the next page.
Press MENU to move to the previous page.
Program
CD
1
2
3
4
TRACK
TRACK
TRACK
TRACK
TRACK
TRACK
TRACK
TRACK
TRACK 02
TRACK 03
TRACK 04
TRACK 05
TRACK 06
Clear All
TRACK 07
0: 56: 18
Program
MP3/WMA
5
TRACK 01
3
STER.
NORM.
Audio CD Menu
2
1.mp3
2.mp3
3.mp3
4.mp3
5.mp3
6.mp3
7.mp3
8.mp3
00:00
Clear All
1
A MP3 file is audio data compressed by using the
MPEG1 audio layer-3 file-coding scheme. Files that
have the “.mp3” file extension are called “MP3 files”.
The player can not read a MP3 file that has a file
extension other than “.mp3”.
About WMA (Window Media Audio)
A WMA file is Microsoft audio compression
technology.
WMA (Windows Media Audio) offers double the audio
compression of the MP3 format.
1. Sampling Frequency / only at 44.1kHz (MP3),
22.05 - 44.1kHz (WMA)
2. Bit rate / within 32 - 320kbps (MP3),
32 - 128kbps (WMA)
3. CD-R physical format should be “ISO 9660”
4. If you record MP3/WMA files using software which
cannot create a FILE SYSTEM, for example “DirectCD” etc., it is impossible to playback MP3/WMA
files. We recommend that you use “Easy-CD
Creator”, which creates an ISO9660 file system.
5. A single session disc requires MP3/WMA files in the
first track. If there is no MP3/WMA file in the 1st
track, it cannot playback MP3/WMA files. If you wish
to playback MP3/WMA files, format all the data in
the disc or use a new one.
6. File names should be named using 8 letters or less
and must incorporate “.mp3” or “.wma” extension
e.g. “********.mp3” or “********.wma”.
7. Do not use special letters such as “/ : * ? “ < > ” etc.
8. Total number of files on the disc should be less than
650.
This DVD player requires discs/recordings to meet
certain technical standards in order to achieve optimal
playback quality. Pre-recorded DVDs are automatically
set to these standards. There are many different types
of recordable disc formats (including CD-R containing
MP3 or WMA files). They require certain pre-existing
conditions (see above) to insure compatible playback.
OFF
MP3/WMA Menu
3
ip
If you are in a file list and want to return to the Folder
4 to highlight
list, use the 3/4
and press
SELECT/ENTER to return to the previous menu screen.
5 To stop playback at any other time, press STOP.
20
About MP3
MP3/WMA Disc compatibility with this player is
limited as follows:
JPEG
MP3/WMA
Notes on MP3/WMA Recordings
Customers should also note that permission is
required in order to download MP3/WMA files and
music from the Internet. Our company has no right
to grant such permission. Permission should always
be sought from the copyright owner.
Audio CD and MP3/WMA Operation (Continued)
CD
MP3
Random With Audio CD
WMA
1. Press PAUSE/STEP during playback.
1. Press RANDOM during playback or in Stop mode.
The unit automatically begins Random Playback and
“RANDOM(1-3)” appears in the display window.
2. To return to playback, press PLAY or press
PAUSE/STEP again.
Changing Track
CD
MP3
WMA
Press SKIP/SCAN . or > briefly during
playback to go to the next track or to return to the
beginning of the current track.
Press SKIP/SCAN . twice briefly to step back to
the previous track.
Listening an audio CD, to go directly to any track,
enter the track number using the numbered buttons
(0-9) during playback.
Search
CD
MP3
WMA
1. Press and hold SKIP/SCAN . or > for about
two seconds during playback.
• RANDOM1: Plays all the tracks on a single disc in random
order and then stops.
• RANDOM2: Plays all the tracks on current disc in
random order and then plays all the tracks on each succeeding disc in random order and then stops.
• RANDOM3: Plays 2 tracks randomly from a disc and then
plays 2 tracks randomly from a different disc until all tracks
on all discs have been played.
2. To return to normal playback, press RANDOM until
“RANDOM” disappears from the display window.
Repeat A-B
CD
To repeat a sequence.
1. During disc playback, press A-B at your chosen start
point.
The Repeat icon and “A * ” appear on the menu screen.
2. Press A-B again at your chosen end point.
The player will now go into SEARCH mode.
2. Press and hold SKIP/SCAN . or > repeatedly
to select the required speed: mX2, mX4, mX8
(backward) or MX2, MX4, MX8 (forward).
Search speed and direction are indicated on the menu
screen.
The Repeat icon and “A B” appear on the menu screen, and
the sequence begins to play repeatedly.
3. To exit the sequence and return to normal play, press
A-B again.
The Repeat icon and “OFF” appear on the menu screen.
3D Surround
3. To exit SEARCH mode, press PLAY.
Random with MP3/WMA Disc
CD
MP3
WMA
1 Press RANDOM during playback or when playback is
stopped.
The unit automatically begins Random Playback and
RANDOM or “RAND.” appears on the display window
and menu screen.
CD
This unit can produce a 3D Surround effect, which
simulates multi-channel audio playback from two
conventional stereo speakers, instead of the five or
more speakers normally required to listen to multichannel audio from a home theater system.
1. Press DISPLAY during playback.
2. Use 1 or 2 to select the sound option.
2 To return to normal playback, press RANDOM repeatedly until RANDOM or “RAND.” disappears on the display window and menu screen.
3. Use 3 or 4 to select “3D SUR”.
Repeat Track/All/Off
Changing Audio Channels
MP3
WMA
1 To repeat the track currently playing, press REPEAT.
The Repeat icon and “TRACK” appears on the menu
screen.
2 To repeat all tracks on a disc, press REPEAT a second time.
The Repeat icon and “ALL” appears on the menu screen.
3 To cancel Repeat mode, press REPEAT a third time.
The Repeat icon and “OFF” appears on the menu screen.
The sound option will be highlighted.
To turn off the 3D Surround effect, select “NORM”.
CD
Press AUDIO repeatedly during playback to hear a
different audio channel (STER., LEFT, or RIGHT).
Repeat Track/Disc/All/Off
CD
1. To repeat the track currently playing, press REPEAT.
The Repeat icon and “TRACK” appear on the menu screen.
2. To repeat all tracks on a disc, press REPEAT a
second time.
The Repeat icon and “DISC” appear on the menu screen.
3.To repeat entire all disc contents, press REPEAT third
time.
The Repeat icon and “All” appears on the menu screen.
4. To cancel Repeat mode, press REPEAT a fourth time.
The Repeat icon and “OFF” appear on the menu screen.
21
OPERATION
Pause
JPEG File Operation
Viewing JPEG Files
Changing Files
JPEG
This DVD Player can play discs with JPEG files. Before
playing JPEG files, read the notes on JPEG files on
right.
1
Insert a disc and close the tray.
The MP3/WMA-JPEG choice menu appears on the
TV screen.
MP3 WMA
While viewing a picture, press SKIP/SCAN . or >
once to advance to the next file or return to the previous
file.
Still Picture
1. Press PAUSE/STEP during slide show.
The player will now go into PAUSE mode.
2. To return to the slide show, press PLAY or press
PAUSE/STEP again.
JPEG
2
4 to select the JPEG option then press
Use 3/4
SELECT/ENTER.
The JPEG menu appears on the TV screen.
To flip the picture
4 while viewing a picture to flip the
Use 3/4
picture horizontally or a vertically.
JPEG
To rotate the picture
Folder1
Folder2
Folder3
Use 1/2 while viewing a picture to rotate the
picture clockwise or counter clockwise.
Folder4
Folder5
Folder6
Folder7
Folder8
Slide Speed
Off
Notes on JPEG Files
3
4 to select a folder, and SELECT/ENTER.
Use 3/4
A list of files in the folder appears.
Press RETURN to move to the MP3/WMA-JPEG
choice menu.
ip
If you are in a file list and want to return to the Folder
list, use the 34 buttons on the remote to highlight
“
” and press SELECT/ENTER to return to the
previous menu screen.
4 to
If you want to view a particular file, use 3/4
4 highlight
a file and press SELECT/ENTER or
PLAY.
Viewing the file function starts.
During viewing a file mode, press RETURN/
DISPLAY to go back to the previous menu
(JPEG menu).
Press TITLE to move to the next page.
Press MENU to move to the previous page.
JPEG
Folder1
Picture1.jpg
Picture2.jpg
Picture3.jpg
Picture4.jpg
Picture5.jpg
Picture6.jpg
Picture7.jpg
5/32
1024X768
Slide Speed
Off
5/32
1024X768
Picture5.jpg
ip
There are several viewing Slide Speed options: Fast,
Normal, Slow, and Off. Use 1/2 to highlight the Slide
Speed then use 3/4 to select the option you want to
use, and then press SELECT/ENTER.
viewing at any other time, press STOP.
5 ToThestop
JPEG menu appears.
22
Depending on the size and number of the JPEG files,
it could take a long time for the DVD player to read
the disc’s content. If you don’t see an on-screen display after several minutes, some of the files are too
big — reduce the resolution of the JPEG files to less
than 2 mega pixels and burn another disc.
Total number of files and folders on the disc should be
less than 650.
Some discs may be incompatible due to different
recording format or condition of the disc.
When you are using software such as “Easy CD
Creator” to burn jpeg files on a CD-R, ensure that all
the selected files have the “.jpg” extension before
copying into the CD layout.
If the files have “.jpe” or “.jpeg” extensions, please
rename them as “.jpg” files.
File names without “.jpg” extension will not be able to
be read by this DVD player, even though the files are
shown as JPEG image files in Windows Explorer.
Programmed Playback
CD
MP3
The Program function enables you to store your favorite
tracks from any disc in the player’s memory.
Programmed Playback with MP3/WMA
Audio CD Programmed Playback
Press PROGRAM during playback or in the Stop
mode to enter the Program Edit mode.
The E mark will appear to the right of the word Program
on the right side of the menu screen.
step 1 of “Audio CD Programmed
1 Follow
Playback” on left.
a track, then press SELECT/ENTER to
2 Select
place the selected track on the Program list.
step 2 to place additional tracks on the
3 Repeat
Program list.
Program
MP3/WMA
Note
Press PROGRAM to exit the Program Edit mode.
The E mark will disappear.
Move to the Disc number selection column by
pressing 3 repeatedly.
2
3 Select an audio disc number using 1/2.
a track, then press SELECT/ENTER to
4 Select
place the selected track on the Program list.
ote
You must select an audio
CD disc number.
3
If selected track is from a different kind of disc (DVD or
MP3 etc.), the track is skipped during programmed
playback.
5
Repeat steps 2-4 to place additional tracks on
the Program list.
Program
CD
1
2
3
4
5
E
TRACK 12
2
TRACK 01
TRACK 08
2
TRACK 02
TRACK 10
1
TRACK 03
TRACK 01
3
TRACK 04
TRACK 06
Clear All
TRACK 07
3
0: 56: 18
2
STER.
NORM.
Audio CD Menu
6
Press 2.
7
4 to select the track you want to start
Use 3/4
playing.
The programmed track you selected last is highlighted on
the program list.
Press TITLE to move to the next page.
Press MENU to move to the previous page.
8 Press PLAY to start.
Playback begins in the order in which you programmed
the tracks and “PROG.” appears on the menu screen.
Playback stops after all of the tracks on the Program list
have played once.
1.mp3
2.mp3
3.mp3
4.mp3
5.mp3
6.mp3
7.mp3
8.mp3
00:00
TRACK 2.mp3
TRACK 4.mp3
TRACK 3.mp3
Clear All
3
OFF
MP3/WMA Menu
steps 6-9 of “Audio CD Programmed
4 Follow
Playback” on left.
Repeat Programmed Tracks
To repeat the track currently playing, press REPEAT.
The Repeat icon and “TRACK” appear on the menu screen.
To repeat all tracks on the program list, press
REPEAT a second time.
The Repeat icon and “ALL” appear on the menu screen.
To cancel Repeat mode, press REPEAT a third time.
The Repeat icon and “OFF” appear on the menu screen.
Erasing a Track from the Program List
1. Press PROGRAM during playback (Audio CD and
MP3/WMA disc only) or in the Stop mode to enter the
Program Edit mode.
The
TRACK 05
E
TRACK 8.mp3
TRACK
TRACK
TRACK
TRACK
TRACK
TRACK
TRACK
TRACK
E
mark will appear.
2. Press 2 to move to the Program list.
4 to select the track that you wish to erase
3. Use 3/4
from the Program list.
4. Press CLEAR.
The track will be erased from the Program list.
Erasing the Complete Program List
1. Follow steps 1-2 of “Erasing a Track from Program
List” as above.
4 to select “Clear All”, then press
2. Use 3/4
SELECT/ENTER.
The complete Program for the disc will be erased.
The programs are also cleared when the disc is removed.
resume normal playback from programmed
9 Toplayback,
select a track from the CD track list
and then press SELECT/ENTER.
“PROG.” indicator disappears from the menu screen.
23
OPERATION
discs
Program can contain 30 tracks.
1
WMA
Troubleshooting
Check the following troubleshooting chart for the possible cause of a problem before contacting service.
Possible Cause
Problem
Solution
No power.
The power cord is disconnected.
Plug the power cord into the wall power
outlet securely.
The power is on, but
the DVD player does
not work.
No disc is inserted.
Insert a disc. (Check that the DVD or,
audio CD indicator in the display
window lights.)
No picture.
The TV is not set to receive DVD signal
output.
Select the appropriate video input
source on the TV so the picture from the
DVD player appears on the TV screen.
The video cable is not connected
securely.
Connect the video cable securely.
The connected TV power is turned off.
Turn on the TV.
The equipment connected with the
audio cable is not set to receive DVD
signal output.
Select the correct input source on the
audio receiver so you can listen to the
sound from the DVD player.
The audio cable is not connected
securely.
Connect the audio cable securely.
The power of the equipment connected
with the audio cable is turned off.
Turn on the equipment connected with
the audio cable.
The Digital Audio Output is set to the
wrong position.
Set the Digital Audio Output to the
correct position, then turn on the DVD
player again by pressing POWER.
The playback picture is
poor.
The disc is dirty.
Clean the disc.
The DVD player does
not start playback.
No disc is inserted.
Insert a disc. (Check that the DVD, or
audio CD indicator in the DVD display
lights.)
An unplayable disc is inserted.
Insert a playable disc. (Check the disc
type, color system, and Regional Code.)
The disc is placed upside down.
Place the disc with the playback side
down.
The disc is not placed within the guide.
Place the disc on the disc tray correctly
inside the guide.
The disc is dirty.
Clean the disc.
A Lock level is set.
Cancel the Rating function or change
the rating level.
The remote control is not pointed at the
remote sensor on the DVD player.
Point the remote control at the remote
sensor on the DVD player.
The remote control is too far from the
DVD player.
Operate the remote control within 23 ft
(7 m).
There is an obstacle between the remote
control and the DVD player.
Remove the obstacle.
The batteries in the remote control are
exhausted.
Replace the batteries with new ones.
No sound.
The remote control
does not work properly.
24
Language Code List
Code
Language
Code
Language
Code
Language
Code
Language
6566
Abkhazian
7074
Fiji
7678
Lingala
8373
Singhalese
6565
Afar
7073
Finnish
7684
Lithuanian
8375
Slovak
6570
Afrikaans
7082
French
7775
Macedonian
8376
Slovenian
8381
Albanian
7089
Frisian
7771
Malagasy
8379
Somali
6577
Ameharic
7176
Galician
7783
Malay
6983
Spanish
6582
Arabic
7565
Georgian
7776
Malayalam
8385
Sudanese
7289
Armenian
6869
German
7784
Maltese
8387
Swahili
6583
Assamese
6976
Greek
7773
Maori
8386
Swedish
6588
Aymara
7576
Greenlandic
7782
Marathi
8476
Tagalog
6590
Azerbaijani
7178
Guarani
7779
Moldavian
8471
Tajik
6665
Bashkir
7185
Gujarati
7778
Mongolian
8465
Tamil
6985
Basque
7265
Hausa
7865
Nauru
8484
Tatar
6678
Bengali; Bangla
7387
Hebrew
7869
Nepali
8469
Telugu
6890
Bhutani
7273
Hindi
7879
Norwegian
8472
Thai
6672
Bihari
7285
Hungarian
7982
Oriya
6679
Tibetan
6682
Breton
7383
Icelandic
8065
Panjabi
8473
Tigrinya
6671
Bulgarian
7378
Indonesian
8083
Pashto, Pushto
8479
Tonga
7789
Burmese
7365
Interlingua
7065
Persian
8482
Turkish
6669
Byelorussian
7165
Irish
8076
Polish
8475
Turkmen
7577
Cambodian
7384
Italian
8084
Portuguese
8487
Twi
6765
Catalan
7465
Japanese
8185
Quechua
8575
Ukrainian
9072
Chinese
7487
Javanese
8277
Rhaeto-Romance
8582
Urdu
6779
Corsican
7578
Kannada
8279
Rumanian
8590
Uzbek
7282
Croatian
7583
Kashmiri
8285
Russian
8673
Vietnamese
6783
Czech
7575
Kazakh
8377
Samoan
8679
Volapük
6865
Danish
7589
Kirghiz
8365
Sanskrit
6789
Welsh
7876
Dutch
7579
Korean
7168
Scots Gaelic
8779
Wolof
6978
English
7585
Kurdish
8382
Serbian
8872
Xhosa
6979
Esperanto
7679
Laothian
8372
Serbo-Croatian
7473
Yiddish
6984
Estonian
7665
Latin
8378
Shona
8979
Yoruba
7079
Faroese
7686
Latvian, Lettish
8368
Sindhi
9085
Zulu
OPERATION
Enter the appropriate code number for the pre-operation settings “Disc Audio”, “Disc Subtitle” and/or “Disc Menu”
(See page 13).
25
Country Code List
Enter the appropriate code number for the pre-operation setting “Country Code” (See page 15).
Code
AD
AE
AF
AG
AI
AL
AM
AN
AO
AQ
AR
AS
AT
AU
AW
AZ
BA
BB
BD
BE
BF
BG
BH
BI
BJ
BM
BN
BO
BR
BS
BT
BV
BW
BY
BZ
CA
CC
CF
CG
CH
CI
CK
CL
CM
CN
CO
CR
CS
CU
CV
CX
CY
CZ
DE
DJ
DK
DM
DO
DZ
EC
EE
EG
EH
26
Country
Andorra
United Arab Emirates
Afghanistan
Antigua and Barbuda
Anguilla
Albania
Armenia
Netherlands Antilles
Angola
Antarctica
Argentina
American Samoa
Austria
Australia
Aruba
Azerbaidjan
Bosnia-Herzegovina
Barbados
Bangladesh
Belgium
Burkina Faso
Bulgaria
Bahrain
Burundi
Benin
Bermuda
Brunei Darussalam
Bolivia
Brazil
Bahamas
Bhutan
Bouvet Island
Botswana
Belarus
Belize
Canada
Cocos (Keeling) Islands
Central African Republic
Congo
Switzerland
Ivory Coast
Cook Islands
Chile
Cameroon
China
Colombia
Costa Rica
Former Czechoslovakia
Cuba
Cape Verde
Christmas Island
Cyprus
Czech Republic
Germany
Djibouti
Denmark
Dominica
Dominican Republic
Algeria
Ecuador
Estonia
Egypt
Western Sahara
Code
ER
ES
ET
FI
FJ
FK
FM
FO
FR
FX
GA
GB
GD
GE
GF
GH
GI
GL
GM
GN
GP
GQ
GR
GS
GT
GU
GW
GY
HK
HM
HN
HR
HT
HU
ID
IE
IL
IN
IO
IQ
IR
IS
IT
JM
JO
JP
KE
KG
KH
KI
KM
KN
KP
KR
KW
KY
KZ
LA
LB
Country
Eritrea
Spain
Ethiopia
Finland
Fiji
Falkland Islands
Micronesia
Faroe Islands
France
France (European
Territory)
Gabon
Great Britain
Grenada
Georgia
French Guyana
Ghana
Gibraltar
Greenland
Gambia
Guinea
Guadeloupe (French)
Equatorial Guinea
Greece
S. Georgia & S. Sandwich
Isls.
Guatemala
Guam (USA)
Guinea Bissau
Guyana
Hong Kong
Heard and McDonald
Islands
Honduras
Croatia
Haiti
Hungary
Indonesia
Ireland
Israel
India
British Indian Ocean
Territory
Iraq
Iran
Iceland
Italy
Jamaica
Jordan
Japan
Kenya
Kyrgyzstan
Cambodia6
Kiribati
Comoros
Saint Kitts & Nevis Anguilla
North Korea
South Korea
Kuwait
Cayman Islands
Kazakhstan
Laos
Lebanon
Code
LC
LI
LK
LR
LS
LT
LU
LV
LY
MA
MC
MD
MG
MH
MK
ML
MM
MN
MO
MP
MQ
MR
MS
MT
MU
MV
MW
MX
MY
MZ
NA
NC
NE
NF
NG
NI
NL
NO
NP
NR
NU
NZ
OM
PA
PE
PF
PG
PH
PK
PL
PM
PN
PR
PT
PW
PY
QA
RE
RO
RU
RW
SA
SB
Country
Saint Lucia
Liechtenstein
Sri Lanka
Liberia
Lesotho
Lithuania
Luxembourg
Latvia
Libya
Morocco
Monaco
Moldavia
Madagascar
Marshall Islands
Macedonia
Mali
Myanmar
Mongolia
Macau
Northern Mariana Islands
Martinique (French)
Mauritania
Montserrat
Malta
Mauritius
Maldives
Malawi
Mexico
Malaysia
Mozambique
Namibia
New Caledonia (French)
Niger
Norfolk Island
Nigeria
Nicaragua
Netherlands
Norway
Nepal
Nauru
Niue
New Zealand
Oman
Panama
Peru
Polynesia (French)
Papua New Guinea
Philippines
Pakistan
Poland
Saint Pierre and Miquelon
Pitcairn Island
Puerto Rico
Portugal
Palau
Paraguay
Qatar
Reunion (French)
Romania
Russian Federation
Rwanda
Saudi Arabia
Solomon Islands
Code
SC
SD
SE
SG
SH
SI
SJ
SK
SL
SM
SN
SO
SR
ST
SU
SV
SY
SZ
TC
TD
TF
TG
TH
TJ
TK
TM
TN
TO
TP
TR
TT
TV
TW
TZ
UA
UG
UK
UM
US
UY
UZ
VA
VC
VE
VG
VI
VN
VU
WF
WS
YE
YT
YU
ZA
ZM
ZR
ZW
Country
Seychelles
Sudan
Sweden
Singapore
Saint Helena
Slovenia
Svalbard and Jan Mayen
Islands
Slovak Republic
Sierra Leone
San Marino
Senegal
Somalia
Suriname
Saint Tome and Principe
Former USSR
El Salvador
Syria
Swaziland
Turks and Caicos Islands
Chad
French Southern
Territories
Togo
Thailand
Tadjikistan
Tokelau
Turkmenistan
Tunisia
Tonga
East Timor
Turkey
Trinidad and Tobago
Tuvalu
Taiwan
Tanzania
Ukraine
Uganda
United Kingdom
USA Minor Outlying
Islands
United States
Uruguay
Uzbekistan
Vatican City State
Saint Vincent &
Grenadines
Venezuela
Virgin Islands (British)
Virgin Islands (USA)
Vietnam
Vanuatu
Wallis and Futuna Islands
Samoa
Yemen
Mayotte
Yugoslavia
South Africa
Zambia
Zaire
Zimbabwe
Specifications
Power requirements
AC 120 V, 60 Hz
Power consumption
14W
Dimensions (Approx.)
16.9 X 3.2 X 16.2 inches (430 x 80 x 410 mm) (w x h x d)
Weight (Approx.)
11.2 lbs (5.1 kg)
Operating temperature
5˚C to 35˚C (41˚F to 95˚F)
Operating humidity
5 % to 90 %
REFERENCE
General
System
Laser
Semiconductor laser, wavelength 650 nm
Signal system
NTSC
Frequency response
DVD (PCM 96 kHz): 8 Hz to 44 kHz
DVD (PCM 48 kHz): 8 Hz to 22 kHz
CD: 8 Hz to 20 kHz
Signal-to-noise ratio
More than 100dB (ANALOG OUT connectors only)
Harmonic distortion
Less than 0.008%
Dynamic range
More than 100 dB (DVD)
More than 95 dB (CD)
Outputs
VIDEO OUT
1 Vp-p 75 Ω, negative sync, RCA jack x 1
S-VIDEO OUT
(Y) 1.0 V (p-p), 75 Ω, negative sync, Mini DIN 4-pin x 1
(C) 0.3 V (p-p) 75 Ω
COMPONENT VIDEO OUT
(Y) 1.0 V (p-p), 75 Ω, negative sync, RCA jack x 1
(Pb)/(Pr) 0.7 V (p-p), 75 Ω, RCA jack x 2
Audio output (digital audio)
0.5 V (p-p), 75 Ω, RCA jack x 1
Audio output (analog audio)
2.0 Vrms (1 kHz, 0 dB), 600 Ω, RCA jack (L, R) x 1
Accessories
S-Video cable . . . . . . . . . . . . . . . . . . . . .1
Video cable . . . . . . . . . . . . . . . . . . . . . . .1
Audio cable . . . . . . . . . . . . . . . . . . . . . . .1
Remote control . . . . . . . . . . . . . . . . . . . .1
Batteries . . . . . . . . . . . . . . . . . . . . . . . . .2
Design and specifications are subject to change without prior notice.
Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic”, and the double-D symbol are trademarks of Dolby
Laboratories.
DTS and DTS Digital Out are registered trademarks of Digital Theater Systems, Inc.
27
ZENITH ELECTRONICS CORPORATION
DVD PLAYER DVB352 LIMITED WARRANTY - USA
Zenith will repair or replace your product, at Zenith’s option, if it proves to be defective in material or workmanship under
normal use, during the warranty period (“Warranty Period”) listed below, effective from the date (“Date of Installation”) of
original installation of the product. This warranty is good only to the original purchaser of the product and effective only when
used in the United States, excluding U.S. Territories.
WARRANTY PERIOD:
HOW SERVICE IS HANDLED:
LABOR: 90 DAYS from the Date of Purchase.
Call 1-877-993-6484 for instructions on getting the defective
unit repaired or replaced.
Please retain dated sales receipt and your box to return the
PARTS: One Year from the Date of Purchase.
unit to Zenith for repair or replacement.
Repaired or Replacement Unit is warranted for the remaining
period of the original warranty.
Both ways shipping charges will be borne by Zenith during the
Warranty Period. After the Warranty Period, you pay in-bound
shipping charges and Zenith pays return shipping charges.
Visit our website at http://www.zenithservice.com
THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TO THE EXTENT ANY
IMPLIED WARRANTY IS REQUIRED BY LAW, IT IS LIMITED IN DURATION TO THE EXPRESS WARRANTY PERIOD
ABOVE. ZENITH WILL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INDIRECT, OR INCIDENTAL DAMAGES OF ANY
KIND, INCLUDING LOST REVENUES OR PROFITS, IN CONNECTION WITH THE PRODUCT. SOME STATES DO NOT
ALLOW LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.
THIS LIMITED WARRANTY DOES NOT APPLY TO:
Damages or operating problems that result from shipping, installation, adjustment of user controls, calibration, maintenance
or failure to maintain, or separate system components; and
Damages or operating problems that result from normal wear and tear, misuse, abuse, operation outside environmental
specifications or contrary to the requirements or precautions in the Operating Guide, accident, lightning strikes or other
natural causes, unauthorized modification or alteration, incorrect electrical current or voltage, signal reception or input, software not licensed directly by Zenith, software errors that do not disable functionality, operating and software protocols adopted after the date of manufacture or for outside the US, institutional or commercial use, or other causes not arising out of
defect in material or workmanship.
The cost of repair or replacement under these excluded circumstances shall be borne by the consumer.
CUSTOMER INTER-ACTIVE CENTER NUMBERS:
For nearest Authorized Service Center,
Where to buy, Product Assistance, or
Customer Assistance
Call 1-877-9Zenith (1-877-993-6484) (Monday~ Friday, 7 AM ~ 8 PM CT;
and Saturday, 8 AM ~ 5 PM CT) and select appropriate options from the menu.
Or visit our website at http://www.zenithservice.com
FOR WARRANTY SERVICE:
You must call 1-877-993-6484 (Monday~ Friday, 7 AM to 8 PM CT; and Saturday, 8 AM ~ 5 PM CT) and select appropriate
options from the menu to confirm the product is defective and to obtain a Return Authorization (RA). During the Warranty
Period, Zenith will send you a return-shipping label. After you obtain an RA for return, please box your unit with a legible
copy of the sales receipt and enough packing material to ensure undamaged delivery of your product. When you receive the
label, place it on the box and call the 800 # in the instructions for pick-up. When your unit is received, Zenith will repair or
replace your unit in accordance with this Limited Warranty.
ADVANCE SHIPMENT. If a replacement unit is available and you want second day delivery, our service representative will
ask for your credit card number. Zenith requires a reserved deposit by credit card as surety for such advance shipment. Your
credit card will not be charged if you return the defective unit in 10 business days. For advance shipment, the return label will
come with the replacement unit sent to you. Please follow boxing and shipping instructions above.
ZENITH ELECTRONICS CORPORATION
2000 MILLBROOK DRIVE
LINCOLNSHIRE, IL 60069
Zenith Part No. 206-3881
GS# 3835RS0060B
Printed in China
Issue O