Panasonic PV-DM2093 Triple Play 20 in. TV/VCR/DVD Combo

Panasonic PV-DM2093 Triple Play 20 in. TV/VCR/DVD Combo
Initial Setup
TV / DVD / VCR Combination
Operating Instructions
PV-DM2093/PV-DM2793
Basic Operation
Model No.
TV Operation
MULTI FORMAT PLAYBACK
*Ability to play back may depend on recording conditions.
As an ENERGY STAR® Partner, Matsushita Electric Corporation
of America has determined that this product or product model
meets the ENERGY STAR® guidelines for energy efficiency.
This operating instruction book is designed for use with models PV-DM2093 and PV-DM2793.
Illustrations in this manual show the PV-DM2093. Features may vary, so please read carefully.
LSQT0667C
Please read these instructions carefully before attempting to connect,
operate or adjust this product. Please save this manual.
Spanish Quick Use Guide is included.
(Guía para rápida consulta en español está incluida.)
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Timer Operation Advanced Operation For Your Information
• Initial Setup and Connection Procedures are on pages 14 to 15.
Important Safeguards and Precautions
READ AND RETAIN ALL SAFETY AND
OPERATING INSTRUCTIONS. HEED ALL
WARNINGS IN THE MANUAL AND ON UNIT
INSTALLATION
1 POWER SOURCE CAUTION
Operate only from power source indicated on unit
or in this manual. If uncertain, have your Electric
Utility Service Company or Video Products Dealer
verify your home power source.
2 POWER CORD PLUG
For safety, this unit has a polarized type plug (one
wide blade), or a three-wire grounding type plug.
Always hold the plug firmly and make sure your
hands are dry when plugging in or unplugging the AC
power cord.
Regularly remove dust, dirt, etc. on the plug.
POLARIZED PLUG CAUTION:
The plug fits into outlet only one way. If it cannot be
fully inserted, try reversing it. If it still will not fit, have an
electrician install the proper wall outlet. Do not tamper
with the plug.
GROUNDING PLUG CAUTION:
The plug requires a three-hole grounding outlet.
If necessary, have an electrician install the proper
outlet. Do not tamper with the plug.
3 POWER CORD
To avoid unit malfunction, and to protect against
electrical shock, fire or personal injury:
- Keep power cord away from heating appliances and
walking traffic. Do not rest heavy objects on, or roll
such objects over the power cord.
- Do not tamper with the cord in any way.
- An extension cord should have the same type plug
(polarized or grounding) and must be securely
connected.
- Overloaded wall outlets or extension cords are fire
hazards.
- Frayed cords, damaged plugs, and damaged or
cracked wire insulation are hazardous and should
be replaced by a qualified electrician.
4 DO NOT BLOCK VENTILATION HOLES
Ventilation openings in the cabinet release heat
generated during operation. If blocked, heat
build-up may result in a fire hazard or heat
damage to cassettes or discs.
For your protection:
a.Never cover ventilation slots while unit is ON,
or operate unit while placed on a bed, sofa, rug,
or other soft surface.
b.Avoid built-in installation, such as a book case
or rack, unless properly ventilated.
5 AVOID EXTREMELY HOT LOCATIONS OR
SUDDEN TEMPERATURE CHANGES
Do not place unit over or near a heater or radiator,
in direct sunlight, inside closed vehicles, in high
temperature [over 95 °F (35 °C)], or in over 75%
humidity. If unit is suddenly moved from a cold place
to a warm one, moisture may condense in unit and
on the tape causing damage. Never subject unit to
vibration, impact, or place it so that the surface is tilted
as internal parts may be seriously damaged.
6 TO AVOID PERSONAL INJURY
• Never place unit on support or
stand that is not firm, level, and
adequately strong. The unit could
fall causing serious injury to a
child or adult and damage to the
unit.
• Move any appliance and
cart combination with care.
Quick stops, excessive force, and uneven surfaces
may cause objects to overturn.
• Carefully follow all operating instructions.
2
OUTDOOR ANTENNA INSTALLATION
1 SAFE ANTENNA AND CABLE CONNECTION
An outside antenna or cable system must be properly grounded
to provide some protection against built up static charges
and voltage. Section 810 of the National Electrical Code,
ANSI/NFPA 70 (in Canada, part 1 of the Canadian Electrical
Code) provides information regarding
proper grounding of the mast and
supporting structure, grounding of the
lead-in wire to an antenna discharge
unit, size of grounding conductors,
location of antenna discharge unit,
connection to grounding electrodes,
and requirements for the grounding
electrode.
2 KEEP ANTENNA CLEAR OF HIGH
VOLTAGE POWER LINES OR CIRCUITS
Locate an outside antenna system well away from power lines
and electric light or power circuits so it will never touch these
power sources should it ever fall. When installing antenna,
absolutely never touch power lines, circuits or other power
sources as this could be fatal.
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
NEC - NATIONAL ELECTRICAL CODE
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
USING THE UNIT
Before unit is brought out of storage or moved to a new location,
refer again to the INSTALLATION section of these safeguards.
1 KEEP UNIT WELL AWAY FROM WATER OR MOISTURE,
such as vases, sinks, tubs, etc.
2 IF EXPOSED TO RAIN, MOISTURE, OR STRONG IMPACT,
unplug unit and have it inspected by a qualified service
technician before use.
3 ELECTRICAL STORMS
During a lightning storm, or before leaving unit unused for
extended periods of time, disconnect all equipment from the
power source as well as the antenna and cable system.
4 WHEN UNIT IS PLUGGED IN
• DO NOT OPERATE IF:
- liquid has spilled into unit.
- unit was dropped or otherwise damaged.
- unit emits smoke, odours, or noises.
Immediately unplug unit, and have it inspected by a service
technician to avoid potential fire and shock hazards.
• Never drop or push any object through openings in unit.
Touching internal parts may cause electric shock or fire
hazard. Do not put any foreign object on the tray.
• Keep magnetic objects, such as speakers, away from unit to
avoid electrical interference.
5 USING ACCESSORIES
Use only accessories recommended by the manufacturer to
avoid risk of fire, shock, or other hazards.
6 CLEANING UNIT
Unplug unit. Use a clean, dry, chemically untreated cloth to
gently remove dust or debris. DO NOT USE cleaning fluids,
aerosols, or forced air that could over-spray, or seep into unit
and cause electrical shock. Any substance, such as wax,
adhesive tape, etc. may mar the cabinet surface. Exposure to
greasy, humid, or dusty areas may adversely affect internal
parts.
SERVICE
1 DO NOT SERVICE PRODUCT YOURSELF
If, after carefully following detailed operating instructions, the
unit does not operate properly, do not attempt to open or remove
covers, or make any adjustments not described in the manual.
Unplug unit and contact a qualified service technician.
2 REPLACEMENT OF PARTS
Make sure the service technician uses only parts specified by
the manufacturer, or have equal safety characteristics as original
parts. The use of unauthorized substitutes may result in fire,
electric shock, or other hazards.
3 SAFETY CHECK AFTER SERVICING
After unit is serviced or repaired, request that a thorough safety
check be done as described in the manufacturer’s service
literature to ensure video unit is in safe operating condition.
Safety Precautions/Mesures de sécurité
Warning :
To prevent fire or shock hazard, do not expose this equipment to rain or
moisture.
Caution :
To prevent electric shock, match wide blade of plug to wide slot, fully insert.
Avertissement : Afin de prévenir tout risque d’incendie ou de chocs électriques, ne pas exposer
cet appareil à la pluie ou à une humidité excessive.
Attention :
Pour éviter les chocs électriques, introduire la lame la plus large de la fiche dans
la borne correspondante de la prise et pousser jusqu’au fond.
FCC WARNING : Any unauthorized changes or modifications to this equipment would void the
user’s authority to operate.
This video recorder, equipped with the HQ (High Quality) System, is compatible with existing VHS
mark. It is recommended that only cassette tapes that
equipment. Only use those tapes with the
have been tested and inspected for use in 2, 4, 6, and 8 hour VCR machines be used. This television
receiver provides display of television closed captioning in accordance with §15.119 of the FCC rules.
CAUTION:
UNIT IS A CLASS I LASER PRODUCT.
HOWEVER THIS UNIT USES A VISIBLE LASER BEAM WHICH COULD
CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE
SURE TO OPERATE THE UNIT CORRECTLY AS INSTRUCTED.
WHEN THIS UNIT IS PLUGGED TO THE WALL OUTLET, DO NOT
PLACE YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY
AND OTHER OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT ATTEMPT TO REPAIR THE
UNIT YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.
CAUTION:
LASER RADIATION
WHEN OPEN. DO NOT
STARE INTO BEAM.
ATTENTION:
RAYONNEMENT LASER
EN CAS D’OUVERTURE.
NE PAS REGARDER
DANS LE FAISCEAU.
(Inside of product)
FCC NOTICE:
This equipment has been tested and found to comply with part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when operated in a residential
environment. If this equipment does cause interference to radio or television reception, which can be
determined by turning the equipment off and on, use the equipment in another location and/or utilize an
electrical outlet different from that used by the receiver. If necessary, consult the dealer or an experienced
radio/TV technician for help. You may find the booklet, “Something About Interference” available from
FCC local regional offices helpful.
This product utilizes both a Cathode Ray Tube (CRT) and other components that contain lead. Disposal
of these materials may be regulated in your community due to environmental considerations. For
disposal or recycling information please contact your local authorities, or the Electronics Industries
Alliance: <http://www.eiae.org.>
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK
OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS
INSIDE REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL
This symbol warns the user that uninsulated voltage within the
unit may have sufficient magnitude to cause electric shock.
Therefore, it is dangerous to make any kind of contact with any
inside part of this unit.
This symbol alerts the user that important literature concerning
the operation and maintenance of this unit has been included.
Therefore, it should be read carefully in order to avoid any
problems.
Region Management Information
This unit is designed and manufactured to respond to the
Region Management Information that is recorded on a DVD
disc. If the Region number described on the DVD disc does
not correspond to the Region number of this unit, this unit
cannot play this disc.
• The region number of this player is “1.”
• The player will play DVD-Video marked with labels containing “1”
or “ALL.”
Example:
1
3
Before Using
Loading the Batteries
Congratulations
On your purchase of one of the most
sophisticated and reliable products on the market
today. Used properly, it will bring you and your
family years of enjoyment. Please fill in the
information below. The serial number is on the
tag located on the back of your unit.
1) Open the cover.
2) Insert batteries as
marked.
Date of Purchase
Dealer Purchased From
3) Close the cover.
Dealer Address
Battery replacement caution
Dealer Phone No.
• Do not mix old and new batteries.
• Do not mix alkaline with manganese batteries.
Model No.
Serial No.
Prevent Accidental Tape Erasure
Break off the tab to
protect.
Record Tab
Accessories
Screw driver
To record again.
Remote Control
LSSQ0372
Cover the hole
with cellophane tape.
Record/Playback Time
Batteries 2 “AA”
Only use tapes with the
Tape Speed
Setting
To order accessories,
call toll free
1-800-332-5368.
4
mark in this unit.
Type of Video Cassette
T60
T120
T160
SP
(Standard
Play)
1 Hour
2 Hours
2 Hours
40 Minutes
LP
(Long Play)
2 Hours
4 Hours
5 Hours
20 Minutes
SLP
(Super Long
Play)
3 Hours
6 Hours
8 Hours
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Table of Contents
TV / VCR
Playback a Tape................................................................................................18
Record On a Tape.............................................................................................18
Copy Your Tapes (Dubbing) ............................................................................19
Basic DVD Operation .......................................................................................20
DVD
TV / VCR
Timer Recording ...............................................................................................30
TV / VCR
Tape Operation .................................................................................................32
Special VCR Features ......................................................................................36
V-Chip Control Feature ...................................................................................38
Audio Features .................................................................................................42
Video/Audio Menu ............................................................................................44
Video/Audio Adjustment..................................................................................45
Disc Operation .................................................................................................46
DVD Operation using On-Screen Displays ....................................................51
MP3/WMA/JPEG Playback Operation .............................................................54
DVD Lock Feature.............................................................................................57
DVD
DVD
TV / VCR
Settings for DVD Operation .............................................................................58
Language Code List .........................................................................................61
Before Requesting Service..............................................................................62
Warning and Instruction Displays ..................................................................64
Spanish Quick Use Guide/Guía para rápida consulta...................................65
Limited Warranty ..............................................................................................72
Customer Services Directory ..........................................................................73
Index ..................................................................................................................74
Timer Operation Advanced Operation For Your Information
TV Operation .....................................................................................................22
MTS Broadcast/TV Stereo System..................................................................23
Closed Caption System ...................................................................................24
TV Timer Features ............................................................................................26
On-Screen Display (OSD) ................................................................................27
FM Radio ...........................................................................................................28
TV Operation
TV / VCR
Basic Operation
Important Safeguards and Precautions ...........................................................2
Safety Precautions/Mesures de sécurité..........................................................3
Before Using .......................................................................................................4
Information (Unit, Cassette, Disc).....................................................................6
Location of Controls ..........................................................................................8
Connections......................................................................................................11
Initial Setup (Ready to Play) ............................................................................14
Reset Language, Channels, Clock, Time Zone Adjust..................................16
Initial Setup
TV / VCR
5
Information (Unit, Cassette, Disc)
Head Cleaning
Specifications
Playing older or damaged tapes may eventually
cause video heads to become clogged.
Display
Head Clog Sensor
Picture Tube
During playback this
screen appears if clogging
is detected. To clear
message from screen,
press PLAY on the remote
or unit.
V I DEO HEADS MAY
NEED CLEAN I NG
PL EASE I NSERT HEAD
CLEAN I NG CASSETTE
OR REFER TO MANUAL
END : PLAY
• Use “dry” type head cleaning cassette only.
(Part No. NV-TCL30PT is recommended.)
• Follow cleaning tape directions carefully. Excessive use
of head cleaning tape can shorten the video head life.
DST (Daylight Saving Time)
Unit auto adjusts clock for DST (Daylight Saving Time.)
■ Spring (First Sunday in April)
DST: ON ➞ Sets clock ahead one hour.
■ Autumn (Last Sunday in October)
DST: OFF ➞ Turns clock back one hour.
• If your area does not observe Daylight Saving Time,
select DST : OFF (see “Clock” on pages 16 and 17).
• Keep these time changes in mind when programming
the unit for timer recordings.
Features for a Quality Picture
Digital Auto Tracking
Continuously analyzes the signal and adjusts for
optimum picture quality.
Manual Tracking Control (to reduce picture noise)
Use during Playback and Slow Motion mode to
reduce picture noise. Press the 3 or 6 NUMBER
on the
keys on the remote control or CH
unit until the picture clears up. To return to Auto
Tracking, press POWER off, then on again a few
seconds later.
V-Lock Control
In Still mode, the 3 or 6 NUMBER keys on the
on the unit operate as a
remote control or CH
V-Lock control to reduce jitter.
PanaBlack™ Picture Tube (PV-DM2793 only)
This unit uses a PanaBlack™ picture tube for better
color reproduction and picture contrast.
Apparatus Claims of U.S. Patent Nos. 4,631,603,
4,577,216, 4,819,098, and 4,907,093, licensed for
limited viewing uses only.
This product incorporates copyright protection
technology that is protected by method claims of
certain U.S. Patents and other intellectual property
rights owned by Macrovision Corporation and other
rights owners. Use of this copyright protection
technology must be authorized by Macrovision
Corporation, and is intended for home and other
limited viewing uses only unless otherwise authorized
by Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
6
VCR
Video Recording
System
Audio Track
20 inch measured diagonal 90°
deflection Picture Tube (PV-DM2093)
27 inch measured diagonal 100°
deflection Picture Tube (PV-DM2793)
4 rotary heads helical scanning
system
1 track (Normal)
2 channel (Hi-Fi Audio Sound)
Tuner
Broadcast Channels VHF 2 ~ 13, UHF 14 ~ 69
Midband A through I (14 ~ 22)
Superband J through W (23 ~ 36)
Hyperband AA ~ EEE (37 ~ 64)
CABLE Channels
Lowband A-5 ~ A-1 (95 ~ 99)
Special CABLE channel 5A (01)
Ultraband 65 ~ 94, 100 ~ 125
FM Radio
Band Range
General
Power Source
Power
On
Power
Consumption Power
Off
Television System
Speaker
Operating
Temperature
Operating Humidity
Weight
Dimensions
(W x H x D)
87.5 MHz ~ 108.1 MHz
120 V AC, 60 Hz
Approx. 134 W (PV-DM2093)
Approx. 170 W (PV-DM2793)
Approx. 3.5 W
EIA Standard NTSC color
2 pieces 3 W (PV-DM2093)
2 pieces 5 W (PV-DM2793)
5 °C ~ 35 °C (41 °F ~ 95 °F)
10 % ~ 75 %
27 kg (59.4 lbs.) (PV-DM2093)
42 kg (92.5 lbs.) (PV-DM2793)
604 mm (23-13/16″) x 523
mm (20-9/16″) x 508 mm (20″)
(PV-DM2093)
772 mm (30-3/8″) x 654 mm (25-3/4″)
x 533 mm (21″) (PV-DM2793)
Discs played
12 cm (5″) single-sided, single-layer
12 cm (5″) single-sided, double-layer
12 cm (5″) double-sided, double-layer
DVD disc
(one layer per side)
(DVD-Video, DVD-R) 8 cm (3″) single-sided, single-layer
8 cm (3″) single-sided, double-layer
8 cm (3″) double-sided, double-layer
(one layer per side)
Compact disc
(CD-DA, VIDEO CD, 5″ (12 cm) disc
3″ (8 cm) disc
CD-R, CD-RW)
MP3, WMA, JPEG
Digital audio output
Optical digital output Optical connector
Pickup
Wavelength
655 nm (DVD)
790 nm (Video CD/CD)
Laser power: CLASS II
Note
• Designs and specifications are subject to change
without notice.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Discs that can be played
Disc
Logo
Disc formats supported by this
unit
DVD-Video
• DVD-Video format
DVD-R
• DVD-Video formatted discs
(finalized*)
It may not be possible to play these
discs in all cases due to the type of
disc or condition of the recording.
Video CD
• Video-CD format
CD-DA
• CD-DA format
CD-R
• CD-DA format
• Video-CD format
• MP3/WMA/JPEG file and finalized*.
CD-RW
• Discs played 8 cm (3″) or 12 cm (5″)
• * A process that allows play on compatible equipment.
Discs which cannot be played with this unit
• CD-ROM
• DVD with Region No. other
• CDV
than “1” or “ALL”
• CVD
• DVD of PAL system
• CD-G
• DVD-ROM
• CD-TEXT
• DVD-AUDIO
• SACD
• DVD-RW
• Photo-CD
• DVD+RW
Definition of Terms
Angle
Some DVD discs feature scenes simultaneously shot from different
angles. The ANGLE button can be used to view the scene from different
angles. (ANGLE Indicator lights up on the unit when a scene recorded at
different angles is detected.)
Chapter Number
Titles are subdivided into numbered sections. You can quickly search for
a favorite scene using these numbers.
DVD
A high-density optical disc on which high-quality pictures and sound have
been digitally recorded. DVD incorporates new video compression
technology (MPEG II) and high-density recording technology which allow
entire movies to be recorded with incredible playback quality.
Playback Control
With Video CD (version 2.0), scenes or information may be selected for
viewing or listening from an interactive menu that appears on the TV
screen.
Subtitles
Written dialogue which appears at the bottom of the screen.
Time Number
The elapsed play time from the start of a disc or title. Use to quickly find
scenes. (May not work with some discs.)
Title Number
For DVD discs with two or more titles, the title is numbered as title 1, title 2,
etc.
Track Number
Numbers assigned to tracks on Video CDs and CDs to allow specific
tracks to be quickly located.
Video CD
CD containing picture and sound with same quality level as video tape.
This unit also supports Video CDs with playback control (version 2.0).
Handling precautions
• Sticking a label on the disc may impair
DVD-R playback.
• Do not attach sticker to discs. (Do not use
discs with exposed adhesive from tape or
left over peeled-off stickers.)
• Only hold disc by
edges as shown.
Fingerprints, dirt, and
scratches can cause
skipping and
distortion.
• Do not write on
label side of disc.
• Never use record
cleaning sprays,
benzine, thinner,
static electricity
prevention
liquids, or
Disc tray
any other
solvent.
Disc
• Be careful
not to drop
or bend
disc.
• Do not place more than 1 disc on disc tray.
• Do not try to close disc tray when disc is not
properly placed.
• Always store discs in their proper cases
when
not in use.
Initial Setup
Disc type
Disc Handling
To clean disc surface
With a soft, damp (water only) cloth,
gently wipe from the center hole to the
outer edge as shown below. (Wiping in a
circular pattern will scratch the surface.)
If disc is brought from a cold to a
warm
environment, moisture may form on
the disc
Wipe away moisture with a soft, dry,
lint-free cloth before using disc. (See
above.)
Improper disc storage
Discs could be damaged if stored or left
in areas:
• exposed to direct sunlight.
• that are humid or dusty.
• near heat (i.e. heater, radiator, etc.).
7
Location of Controls
Remote Control Buttons
EJECT/OPEN/CLOSE
See next page.
TV/VCR
Sets to TV/VCR mode.
POWER
Turns the unit on or off.
DVD
Sets to DVD mode.
DISPLAY
Displays the TV status and
clock. In DVD mode, displays
disc and unit information.
RAPID TUNE
Displays the last channel
you were watching.
MUTE
Mutes the sound instantly.
FM
Receives FM radio signal.
ACTION
Displays Main Menu.
CHANNEL UP/DOWN
Selects a channel.
REW/SLOWRewinds tape and searches reverse
scene. Decreases slow motion speed
in Still mode.
NUMBER Keys
Selects a channel directly.
ADD/DELETE/CLEAR
Adds or deletes a channel.
Cancels an item on the screen.
MENU
Displays DVD menu.
SELECT
Controls navigation around
on-screen menu.
SET
Sets a selected menu.
VOLUME UP/DOWN
Adjusts volume.
PLAY
Begins playback.
STOP
Stops recording or playback.
FF/SLOW+
Fast forwards tape and forward
visual search. Increases slow
motion speed in Still mode.
STILL/PAUSE
Pauses picture in Playback mode and
frame advance picture in Still mode.
TITLE
Selects the desired title by
number on some DVDs.
/SEARCH
SKIP- |
Skips back one chapter or track.
Goes to previous menu screen. Goes
directly to the desired recording.
| /CM SKIP/ZERO
SKIP+
SEARCH
Skips one chapter or track. Goes
to next screen. In Stop mode,
goes to the counter “0:00:00.” In
Playback mode, skips over 1 to
3 minutes of tape.
AUDIO
Selects the desired audio
mode.
PROGRAM
Displays SET PROGRAM
screen. You can set Timer
Program and On-Timer.
REC
Records a program.
ANGLE
Selects the desired angle in
DVD mode.
8
TRACKING UP/DOWN
Reduces picture noise during
Playback and Slow Motion.
SURROUND/V.S.S.
Creates a deeper, 3-D sound
effect.
SUB TITLE
Selects a different subtitle
language.
ZOOM/COUNTER RESET
Enlarges specific portions of
DVD picture. Resets to “0:00:00”
at desired portion of tape.
RETURN/SPEED
Returns to DVD menu screen.
Selects recording speed of tape.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
EJECT/OPEN/CLOSE button:
Initial Setup
When this button is pressed in TV-VCR mode, the tape is ejected.
This button is inoperative if pressed during recording.
If pressed in DVD mode, the disc tray opens or closes.
Indicators on the Front Panel
<Model PV-DM2093 unit shown>
REC Indicator (RED)
Lights during recording.
In Rec Pause or OTR
Pause mode, the indicator
flashes.
Pg 18.
Remote Sensor
ON TIMER Indicator (ORANGE)
Lights when the On Timer is set.
Pg 26.
ANGLE Indicator (RED)
Lights when a scene
recorded at a different angles
is detected. (DVD only).
Pg 47.
PROG TIMER Indicator
(GREEN)
Lights when the unit is set for
Timer Recording. It flashes
when a Timer Recording
has been set with no tape
inserted, the clock is not set,
or the tape is in motion.
Pg 30.
9
Location of Controls (continued)
Front View of the unit
<Model PV-DM2093 unit shown>
Built In Speaker
If the disc cannot be removed,
First unplug unit.
Then, prepare a rigid wire (e.g.
an extended paper clip, etc.) and,
applying moderate force, insert it
straight into the hole at the base
of the tray. The tray will eject a
little. Now, pull the tray all the way
out and remove the disc.
Disc Tray
Phones Jack
Connect an earphone
or headphones.
Tape Operation
REC
Records a program.
Audio/Video Input
Connector
Connect from other
component.
FAST FORWARD/SEARCH
Fast forwards tape and
forward visual search.
Increases slow motion
speed in Still mode.
POWER
Turns the unit on or off.
PLAY
Begins playback.
REPEAT
Set to see a recording over
and over.
Disc Operation
STOP
Stops playback.
PAUSE
Pauses picture in Playback mode
and frame advance picture in Still
mode.
PLAY
Begins playback.
SKIP
Skips back one chapter or track.
Goes to previous menu screen.
SKIP
Skips one chapter or track.
Goes to next screen.
OPEN/CLOSE
Opens or closes the disc tray.
10
Cassette Compartment
REWIND/SEARCH
Rewinds tape and searches
reverse scene. Decreases
slow motion speed in Still
mode.
STOP
Stops playback.
EJECT
Eject the tape.
TV/FM
Sets to TV/FM mode.
CHANNEL UP/DOWN
Selects a channel.
TRACKING UP/DOWN
Reduces picture noise during Playback
and Slow Motion.
VOLUME UP/DOWN
Adjusts volume.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Rear View of the unit
Initial Setup
<Model PV-DM2093 unit shown>
Audio Output
Connector (L/R)
Pg. 12
VHF/UHF Antenna
Input Terminal
See below.
AC Power Plug
When plugged into an AC
outlet, this unit consumes 3.5 W of
electric power in OFF condition.
Optical digital audio
output connector
Pg. 12
Connections
For ANT./Cable
Connect the cable from
Antenna/Cable to the VHF/UHF
terminal on the unit.
VHF/UHF
IN from
ANT./CABLE
VHF/UHF
For DSS/Cable Box
Connect the OUT jack on your
cable box to the VHF/UHF terminal
on the unit with a RF cable.
Cable TV
Converter Box
VHF/UHF
WARNING
Overtightening “Nut type” RF coaxial cables
may damage jacks. Finger tighten only.
IN from
ANT./CABLE
VHF/UHF
11
Connections (continued)
Audio connections
Enjoy the powerful movie theater and hall-like sound available with multiple channel audio found on
DVDs by connecting an amplifier and speakers. There are two types of connection, digital and analog.
■Digital connection
■Analog connection
Connect an amplifier with Dolby Digital and
DTS decoders to enjoy surround sound.
You can also enjoy stereo sound with sampling
frequencies of 48 kHz if the material isn’
t copy-protected and the equipment you
connect is compatible with these signals.
Connect an amplifier to enjoy high-quality
stereo sound with sampling frequencies of
96 kHz.
DIGITAL AUDIO OUT
PCM/BITSTREAM
OPTICAL COXIAL
Firmly
connect the
cable to the
connector.
OPTICAL
Speakers (example)
Speakers (example)
Connect three or
more speakers for
surround sound.
12
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
IMPORTANT NOTE:
Check List
Enjoying digital audio output from the
digital audio output connector
Notes on audio output from the optical
digital audio output connector
Disc
Sound
recording
format
Dolby Digital
DVD
Linear PCM
(48/96 kHz
16/20/24 bit)
dts
Video CD MPEG 1
CD
Linear PCM
MP3
MP3
WMA
WMA
Optical digital audio output
from connector
Dolby Digital bitstream
(1-5.1 ch) or PCM (48 kHz
sampling/16 bit only)*1
Linear PCM (2ch)
(48 kHz sampling/16 bit
only)*2
Bitstream or PCM (48 kHz
sampling/16 bit only)*1
PCM
(44.1 kHz sampling)
Linear PCM
(44.1 kHz sampling)
Linear PCM
(It depends on the MP3 file)
Linear PCM
(It depends on the WMA file)
Caution for optical digital audio
output connector:
• When connecting an amplifier (with an Optical
digital input connector) which does not contain
the Dolby Digital or dts decoder, be sure to
select “PCM” at “Dolby Digital” and “PCM” at
“dts” of the Settings for DVD Operation “AUDIO
OUTPUT” (see page 59). Otherwise, any
attempt to play DVDs may cause such a high
level of noise that it may be harmful to your
ears and damage your speakers.
• When a dts decoder is connected, please
select “Bitstream” at “dts” of the Settings for
DVD Operation “AUDIO OUTPUT.” If “PCM”
is selected, there will be stereo sound. (See
page 59).
• Video CDs and CDs can be played as usual.
Initial Setup
Turn down the volume, then turn this unit, as well
as other equipment to be connected, off before
proceeding with connection.
Do not block ventilation holes of any equipment
and arrange them so that air can circulate freely.
Read through the instructions before connecting
other equipment.
Ensure that you observe the color coding when
connecting audio and video cables.
Note
• Some dts decoders which do not support
DVD-dts Interface may not work properly with
the unit.
Manufactured under license from
Digital Theater Systems, Inc. US Pat.
No. 5,451,942, 5,956,674, 5,974,380,
5,978,762 and other world-wide patents
issued and pending. “DTS” is a registered
trademark of Digital Theater Systems,
Inc. Copyright 1996, 2000 Digital Theater
Systems, Inc. All rights reserved.
Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D
symbol are trademarks of Dolby
Laboratories.
*1 The type of audio output from the connector can be
selected by the Settings for DVD Operation. (See
page 59.)
*2 Sound having 96 kHz sampling is converted into
48 kHz sampling when it is output from the unit’s
optical digital audio output connector.
For your reference:
• Dolby Digital is a digital sound compression technique
developed by the Dolby Laboratories Licensing Corporation.
Supporting 5.1-channel surround sound, as well as stereo
(2-channel) sound, this technique enables a large quantity of
sound data to be efficiently recorded on a disc.
• Linear PCM is a signal recording format used in CDs. While
CDs are recorded in 44.1 kHz/16 bit, DVDs are recorded in
48 kHz/16 bit up to 96 kHz/24 bit.
• If you have a Dolby Pro Logic Surround decoder, you
will obtain the full benefit of Pro Logic from the same
DVD movies that provide full 5.1 channel Dolby Digital
soundtracks, as well as from titles with the Dolby Surround
mark. For information on Panasonic or Technics Dolby Pro
Logic Surround Sound Decoders please contact your local
dealer.
13
Initial Setup (Ready to Play)
Please make all cable or antenna connections before powering on.
Initial Setup (Ready to Play)
Press TV/VCR on the remote for TV-VCR mode.
TV/VCR
1
Plug the unit power cord into an AC wall outlet.
2
Press POWER* on the remote or unit. The unit
comes on and auto channel and clock set
starts.
POWER
EJECT
ACTION
SELECT
CH AUTO SET PROCEEDING
SET
• If you use a cable box, turn it on and set it to the Public
Broadcasting Service (PBS) channel in your time zone. If you
use a DSS receiver, it must be turned off.
AUTO CLOCK SET
PROCEEDING
CANCEL : PRESS STOP KEY
3
Settings are made automatically. When setup
is done, this screen appears.
2 / 6 / 2003 THUDST
12 :: ON
00PM
SETT I NG : CH 1 0
AUTO CLOCK SET
COMPLETED
STOP
If AUTO CLOCK SET IS INCOMPLETE screen appears,
set the clock using MANUAL CLOCK SET procedure on
next page.
AUTO CLOCK SET
I S I NCOMPLETE
PLEASE SET CLOCK BY
PRESS I NG ACT I ON KEY
14
Notes
• Function buttons are inoperative during
Initial Setup.
• To remove a cassette during Auto Set,
press EJECT twice on the remote or
STOP twice on the unit. In this case,
settings must be made manually. (See
pages 16-17.)
• Depending on conditions, Auto Clock
Set may take longer than 30 minutes.
If so, press STOP to stop setup and
perform settings manually. (See pages
16-17.)
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
*Important: If a remote control button does not work when pressed, press the TV/VCR button on
the remote and try the button again.
Manual Clock Set
Reset all unit Memory Functions
When moving unit to a new location, or if a mistake
was made in the Initial Setup section.
• Make sure a tape is not inserted in the unit.
1
Press ACTION on the remote to display
SET CLOCK Menu screen.
Initial Setup
If AUTO CLOCK SET was incomplete, manually
set the clock as follows.
SET CLOCK
DST : ON
SELE CT MONTH
SELECT :
SET
: SET
END
: ACT I ON
2
Press
to select the month and press
SET to set. In the same manner, select
and set the date, year, time, and DST
(Daylight Saving Time).
THU
3
Press ACTION twice to start CLOCK and
exit.
1
Turn the unit Power
on.
2
Press and hold both PLAY and FF on the unit
for more than 5 seconds.
3
Perform “Initial Setup” on page 14.
• The power will shut off.
• Please ignore “NO CASSETTE” warning.
Note to CABLE system installer:
This reminder is provided to call the CABLE (Cable TV) System Installers attention to Article 820-40
of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the building, as close to the point of cable entry
as practical.
15
Reset Language, Channels, Clock,
1
Press ACTION*
M A I N MENU
DVD
LOCK LANGUAGE
53
TV
2
CH
CLOCK
SELECT :
END
: ACT I ON
to display MAIN MENU.
1
SET : SET
■ Language
■ Channels
1) Press
to
select language
icon.
■ Clock
to
1) Press
select “CH.”
1) Press
to
select “CLOCK.”
M A I N MENU
M A I N MENU
M A I N MENU
DVD
DVD
LOCK LANGUAGE
5
TV
1
CH
CLOCK
SELECT :
END
: ACT I ON
3
LOCK LANGUAGE
53
TV
CH
CLOCK
SELECT :
END
: ACT I ON
SET : SET
2) Press SET.
SET UP CHANNEL
MENU PRINCIPAL
HOLA
BLOQUEO IDIOMA
53
TV
1
CANAL
RELOJ
ELEGIR :
FIJAR : SET
TERMINAR : ACT I ON
For Spanish
MENU
BONJOUR
DVD
BLOCAGE LANGUE
TELE
HORLOGE CANAL
53
SEL. :
FIN
1
REGLER : SET
: ACT I ON
For French
M A I N MENU
DVD
HELLO
1
CH
CLOCK
SELECT :
END
: ACT I ON
SET : SET
For English
3) Press ACTION
to exit.
16
1
CH
CLOCK
SELECT :
END
: ACT I ON
SET : SET
ANTENNA : CABLE
AUTO SET
WEAK S I GNAL D I SPLAY : OFF
SELECT :
SET
: SET
END
: ACT I ON
3) Press
to select
“ANTENNA,” then
press SET to set
your antenna system
(“TV” or “CABLE”).
4) Press
to select
“AUTO SET,” then
press SET.
• After Channel Auto Set
is finished, Clock Auto
Set will be performed.
(If clock is set manually, Clock
Auto Set will not be performed.)
2) Press SET.
SET CLOCK
AUTO CLOCK SET
MANUAL
T I ME ZONE ADJUST : 0
SELECT :
SET
: SET
END
: ACT I ON
(“TIME ZONE ADJUST”
appears only when
auto clock is set.)
3) Press
to select
“MANUAL,” then
press SET.
(For Auto Clock Set,
select “AUTO CLOCK
SET,” and press SET.)
SET CLOCK
2 / 6/2003 THU 12: 00PM
DST : ON
SELE CT HOUR
LOCK LANGUAGE
53
TV
53
TV
SET : SET
2) Press SET
repeatedly.
DVD
LOCK LANGUAGE
DVD
1
SELECT :
SET
: SET
START : ACT I ON
BACK :
<Example MANUAL
CLOCK SET screen>
Continued on
the next page.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Time Zone Adjust
NUMBER
keys
4) Press
and
press SET to
select and set the
month, date, year,
time, and DST
(Daylight Saving
Time).
To Make
Corrections,
repeatedly press
to move to
error, then correct.
5) Press ACTION
twice to start the
clock and exit this
mode.
■ Time Zone Adjust
ADD/DLT
(Only when Auto Clock is set.)
ACTION
SELECT
1) Press
to
select “CLOCK.”
SET
M A I N MENU
DVD
TV
CH
LOCK LANGUAGE
53
1
CH
CLOCK
SELECT :
END
: ACT I ON
Initial Setup
*Important:
If a remote control button does not work when pressed,
press the TV/VCR button on the remote and try the button
again.
SET : SET
2) Press SET.
SET CLOCK
AUTO CLOCK SET
MANUAL
T I ME ZONE ADJUST : 0
SELECT :
SET
:
: ACT I ON
END
3) Press
to select
“TIME ZONE
ADJUST” and
press or
to subtract or
add hour(s) as
necessary.
Add or Delete a Channel
To add channel:
Select channel with NUMBER
keys and press ADD/DLT.
CHANNEL 08 ADDED
SET CLOCK
AUTO CLOCK SET
MANUAL
T I ME ZONE ADJUST : +1
SELECT :
SET
:
: ACT I ON
END
4) Press ACTION
twice to exit.
• “TIME ZONE
ADJUST” returns
to “0” if clock is set
manually.
To delete channel:
Select channel with CH
or NUMBER keys and press
ADD/DLT.
CHANNEL 08 DELE TED
17
Playback a Tape
Check List
Cable or antenna is connected.
Power cord is plugged in.
Insert a cassette.
1
• The unit power comes
on automatically.
Record tab
Record On a Tape
1
2
3
To prevent tape jam,
remove loose or peeling
labels from tapes.
2
• If tape has no record tab (see page 4), auto play
begins.
■ Forward/Reverse scene search
➞Press FF/SLOW+ or REW/SLOW-.
➞Press again or PLAY to release.
■ Still (Freeze) picture
➞Press STILL/PAUSE.
➞Press PLAY to release.
■ Slow Motion picture
➞Press FF/SLOW+ (increases speed) or
REW/SLOW- (decreases speed) in Still
mode.
➞Press PLAY to release.
■ Frame by Frame picture
➞Press STILL/PAUSE in Still mode.
➞Press PLAY to release.
Notes
• These features work best in SP or SLP mode.
• After the unit is in Still or Slow mode for 3 minutes, it will
switch to Stop mode automatically to protect the tape
and the video head.
■ Stop ➞ Press STOP
■ Rewind tape ➞ Press REW/SLOW- in
Stop mode
■ Fast forward tape ➞ Press FF/SLOW+
in Stop mode
■ Eject tape ➞ Press EJECT on the
remote or STOP/EJECT on the unit
Operation using unit buttons
PLAY/REPEAT
CH
• The unit power comes on automatically.
Press CH
or NUMBER keys to
select a channel.
• For “LINE” input, see bottom of next page.
Press SPEED to select recording speed
(see page 4).
SP = Standard Play
LP = Long Play
SLP = Super Long Play
• Selected speed is displayed.
Press PLAY* to play a tape.
Insert a tape.
Insert a tape with record tab.
REC
4
Press REC to start recording.
• To edit out unwanted portions, press
STILL/PAUSE to pause and resume recording.
• You cannot view another channel during
recording.
■ Stop ➞ Press STOP
■ One Touch Recording (OTR)
[recording in progress]
Press REC
Normal Rec
repeatedly to set
4:00
3:00
the recording
length (30 min - 4 hours.)
0:30
2:00
1:00
1:30
• The unit stops recording at a preset time.
• PROG TIMER Indicator lights on the unit.
Notes
• It is not possible to record from DVD/Video CD/CD
to VHS tape using this unit.
• After the unit has been in Rec Pause mode for 5
minutes, it will stop automatically to protect the tape
and the video head.
• The remaining recording time of an OTR can be
displayed by pressing DISPLAY.
EJECT
DISPLAY
ACTION
NUMBER
keys
SELECT
CH
STOP
STILL/
PAUSE
SET
PLAY
FF/SLOW+
REW/SLOWREC
Press to stop
and/or eject tape.
18
SPEED
REC Indicator
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
e
Copy Your Tapes (Dubbing)
*Important:
If a remote control button does not work when pressed, press the TV/VCR button on the remote
and try the button again.
Connections you’ll need to make
Recording (Editing) unit
Playing (Source) VCR
IN
MONO
IN FROM
ANT.
OUT TO
TV
Playback (Source)
1
VIDEO IN L-AUDIO IN-R
Recording (Editing) unit
Basic Operation
OUT R-AUDIO-L VIDEO
Insert blank tape with
record tab.
Insert pre-recorded
tape.
• Dubbing tapes protected with
Copy Guard will have poor
quality results.
2
3
Select “LINE” mode.
See “Selecting Input Mode” below.
Press PLAY then press
PAUSE at starting point
to put in Standby mode.
Press REC, then press
STILL/PAUSE immediately to
put in Standby mode.
(Perform operation of steps 4 and 5 on both units at same time.)
4
Press PLAY
to start dubbing.
Press STILL/PAUSE to start
dubbing.
5
Press STOP
to stop dubbing.
Press STOP to stop dubbing.
STOP
Selecting Input Mode
Method 1:
Caution
• Unauthorized exchanging and/or copying
of copyrighted recordings may be copyright
infringement.
• Please note that some tapes cannot be dubbed on
this unit. Also, it is not possible to dub DVD/Video
CD/CD to VHS tape using this unit.
Press CH
follows.
. The display will change as
1
2
LINE
3
(CABLE) (TV)
125 or 69
Method 2:
a Press ACTION for MAIN MENU.
to select “TV,” then press SET
b Press
for SET UP TV screen.
c Press
to select “INPUT SELECT,” and then
press SET to select “TUNER” or “LINE.”
d Press ACTION twice to exit this mode.
19
Basic DVD Operation
Check List
Cable or antenna is connected.
Power cord is plugged in.
If unit is connected to an audio amplifier, turn
the stereo system’s power on.
1
2
Press POWER* on the remote or unit.
Insert a disc.
• If a disc is already inserted, go to step 3.
(Depending on the disc, playback may start
automatically.)
1) Press OPEN/CLOSE.
2) Place disc into disc tray.
OPEN/
CLOSE
DVD
POWER
1
2
NUMBER
keys
MENU
SELECT
10
3
Press PLAY to start play. Disc tray
closes automatically.
• You may also close
the tray by pressing
OPEN/CLOSE.
• Data reading time differs
with each disc.
CLOSE
SET
REW/
SLOW-
READING
PLAY
<Example 1>
FF/SLOW+
STOP
STILL/
PAUSE
TITLE
SKIP-
SKIP+
|
|
RETURN
T I TLE MENU
If an interactive DVD*1
or a Video CD with
playback control*2 is
used and a TITLE MENU
appears, go to step 4.
4
T I TLE MENU
Dogs
Cas t l es
B i r ds
Dogs
Love r s
Operation using unit buttons
of the world
3 Press PLAY.
2 Insert disc.
• Hold disc by its edges only (page
7) with printed side up and use
guides to place into tray. Use 1
3″(8 cm) or 2 5″ (12 cm) disc.
2•6
Press
OPEN/CLOSE.
<Example 2>
Dogs
Cas t l es
Love r s
B i r ds
Press
or
NUMBER key(s)
(see below) to
select title, and
press SET or PLAY
to start playing.
• “Pressing SET or
PLAY” is not
necessary when using
NUMBER keys.
Using NUMBER key(s) starts play automatically.
The number of available titles varies with each disc.
<Input Example>
1 digit number 1 ••• 1
2 digit number 12 ••• 10➞1➞2
3 digit number 123 •••100➞1➞2➞3
| or SKIP- |
Press SKIP+
to go to next or
previous menu screen.
1Press POWER. 5 Press STOP.
*1 Interactive DVD...
May include multiple camera angles, stories, etc.
*2 Video CD with playback control...
Particular scenes or information can be
interactively selected from a menu that appears
on the screen.
20
• SKIP function not available with all discs.
Please refer to disc jacket for operation information.
To return to MENU (play stops)
Press TITLE, MENU, or RETURN. (DVD)
Press RETURN. (Video CD)
5
6
Press STOP to stop play.
Press OPEN/CLOSE to eject the disc.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
*Important: If a remote control button does not work when pressed, press the DVD button on
the remote and try the button again.
■ Forward/Reverse rapid scene search
➞ Press FF/SLOW+ or REW/SLOWduring play.
➞ Press PLAY to release.
• Starting forward/reverse search during play started from
menu on Video CDs may recall menu.
• Search speed, slow at first, increases with each
additional press of the button up to 5 levels.
■ Forward/Reverse Chapter/Track Skip
Pressing SKIP- |
once midway through a
chapter/track returns to start of that chapter/track.
Each additional press skips back one chapter/track.
| or SKIP-|
• Pressing SKIP+
during play
started from menu on Video CDs may recall menu.
Current playback position
Chapter/Track Chapter/Track Chapter/Track Chapter/Track
Reverse Skip
Forward Skip
■ Still (Pause) Picture
➞ Press STILL/PAUSE during play.
➞ Press PLAY to release.
• DVD/Video CD : The unit will enter Still picture mode.
• CD : The unit will enter Pause mode.
■ Frame by Frame picture (DVD/Video
CD)
RESUME function
The unit memorizes the point where STOP is
pressed (STOP display on the screen).
Press PLAY to resume play from this point.
Pressing STOP again or opening the tray cancels
RESUME, however, RESUME is not canceled
when power is turned off and on.
• RESUME works only with discs for which elapsed
play time is displayed during play.
Auto-Power Off function
Basic Operation
| or SKIP-|
during
➞ Press SKIP+
play.
Each press skips a chapter (DVD) or track
(Video CD/CD).
• When
appears on the screen while a
button is being pressed, it means that the
corresponding operation is prohibited by the
unit or the disc.
Power turns off after unit has been in Stop mode
(DVD) for about 5 minutes.
Enjoy Video CDs featuring
playback control without using
menus (Video CDs only)
1. Do steps 1-3 (previous page).
When menu appears, press STOP.
2. Press NUMBER key(s) to select desired
track (play begins).
• Check disc for track numbers.
• Press “1” to start at beginning of disc.
To Resume Menu use,
Press STOP, and press PLAY, then the menu
appears. Now, go to step 4 (previous page).
➞ Press STILL/PAUSE in Still mode.
➞ Press PLAY to release.
• Each press advances picture one frame.
• Hold down for consecutive frame advance.
• Whether pictures are advanced by “FRAME” or
“FIELD” is selected automatically (see page 60).
■ Slow Motion picture (DVD/Video CD)
➞ Press FF/SLOW+ or REW/SLOW- (DVD
only) in Still mode.
➞ Press PLAY to release.
Notes
• Please read the disc jacket for operation information.
• If a single sided disc is placed in upside down, “THIS
TYPE OF DISC CANNOT BE PLAYED. PLEASE
INSERT A DIFFERENT DISC” is displayed.
• Remove disc and press unit POWER off when not in
use.
• Disc continues to rotate with menu displayed even
after play is done. Press STOP to clear menu display
when finished with menu.
• Slow motion speed, slow at first, is increased with
each additional press of the button up to 5 levels.
• Reverse slow motion is not available for video CDs.
21
TV Operation
1
*Important: If a remote control button does not work
when pressed, press the TV/VCR button on
the remote and try the button again.
Press POWER* on the remote or unit.
Check List
Cable or antenna is connected.
Power cord is plugged in.
2
CH08
Use CH
or
NUMBER keys to
select a channel.
VOL + / VOL POWER
Press VOL + or
VOL - to adjust
volume.
3
PHONES
Jack
24
CH
POWER
RAPID
TUNE
MUTE
NUMBER
keys
■ Using the 100 key
When selecting CABLE channels 100 to 125 with
the NUMBER keys, first press the 100 key, and
then enter the remaining two digits.
100 Key
■ Rapid Tune
Press R-TUNE to display the last channel you
were watching.
CH
VOL+/-
■ Audio Mute
Press MUTE to instantly mute the sound. Press
again to restore the previous sound level.
■ Phones
Connect an earphone (not supplied) or headphones
(not supplied) to the Phones Jack.
22
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
MTS Broadcast/TV Stereo System
Equipped with
-TV
Noise Reduction for true MTS
reproduction.
-TV Noise
Reduction is required for good
stereo separation and audio fidelity.
is a registered trademark,
and is licensed by
Technology
Licensing.
Receivable Broadcast Types
The following are possible audio broadcast types and
on-screen displays. The signal being received is indicated with
an “ ” mark while the selected audio mode is indicated with
an arrow. To change the audio mode for these broadcasts, see
the “Audio Mode for TV Viewing” section below.
Press DISPLAY to display the broadcast signal being
received.
1 2 : 0 0AM
CH08
SP
STEREO
SAP
MONO
DISPLAY
1 2 : 0 0AM
CH08
SP
MTS Stereo broadcast
Multi-channel Television Sound Stereo
broadcast. Select STEREO audio
mode.
• If stereo broadcast is weak and the
display flickers, select MONO audio mode
for possible improvement.
1 2 : 0 0AM
CH08
SP
STEREO
SAP
MONO
SAP broadcast
Secondary Audio Program (sub
language). Select SAP audio mode for
the sub language.
TV Operation
STEREO
SAP
MONO
MTS Stereo and SAP broadcast
Multi-channel Television Sound Stereo
(main language) and Secondary Audio
Program (sub language) broadcasts are
being received simultaneously. Select
the STEREO or SAP audio mode.
AUDIO
1 2 : 0 0AM
STEREO
SAP
MONO
CH08
SP
MONO broadcast
Normal monaural sound broadcast.
Audio Mode for TV Viewing
Press AUDIO to select the desired audio mode as described above.
(Arrow shows selection.)
• Each press of AUDIO will change the audio mode as shown below.
• “SAP” is selected with first press of AUDIO.
< Example >
Press AUDIO
STEREO
SAP
MONO
STEREO
SAP
MONO
STEREO
SAP
MONO
Press AUDIO
Press AUDIO
23
Closed Caption System
Closed Caption is ...
This multi-use system not only allows the hearing impaired to enjoy selected programs, but also makes
useful information from TV stations available to everyone.
Closed Caption Mode Feature
1
2
Press ACTION* to display MAIN MENU.
M A I N MENU
LOCK LANGUAGE
DVD
53
TV
SELECT :
END
: ACT I ON
3
SET : SET
SET UP TV
CAPT I ON
I NPUT SELECT
: TUNER
SET UP V I DEO / AUD I O
DVD VOL ADJUST : + 2
FM ANTENNA
: I NT
SET : SET
SELECT :
END
: ACT I ON
4
1
CH
CLOCK
CAPT I ON
CAPT I ON MODE
CC ON MUTE
: CAP C1
: CAP C1
SELECT :
SET
: SET
END
: ACT I ON
OFF
CAP C1
TEXT C2
1) Press
to select “TV.”
2) Press SET to
display SET
UP TV screen.
1) Press
to
select
“CAPTION.”
2) Press SET to
display
CAPTION
screen.
1) Press
to
select
CAPTION
MODE.
2) Press SET
repeatedly to
select mode.
(See left.)
Closed Caption Mode Selections
Caption Mode: CAP C1 or C2
A narration of selected TV
programs is displayed.
Check TV program listings for CC
(Closed Caption) broadcasts.
Caption Mode: TEXT C1 or C2
Most of the screen will be
blocked out. When the TV station
broadcasts information, such as
program listings, it will appear in
this space.
Caption Mode: OFF
Closed Caption/Text narration will
not be displayed.
Notes
• The closed caption or text signal may
be broadcast over C1, C2, or both.
Also, text contents can vary so you
may wish to try different settings.
• While recording one station and
watching another, Captioning will
not be displayed.
TEXT C1
CAP C2
5
Press ACTION three times to return to
the normal screen.
Recording and Playing Back a Closed Caption/Text Program
Record : Record normally. Closed Caption/Text signal, if present, is recorded
automatically.
Playback : Start playback. Perform above steps to select desired caption mode.
24
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
*Important: If a remote control button does not work when pressed, press the TV/VCR button
on the remote and try the button again.
Caption On Mute Feature
Closed Caption narration, if available, is displayed when
MUTE button is pressed for silence.
1
Press ACTION to display MAIN MENU.
2
M A I N MENU
LOCK LANGUAGE
DVD
53
MUTE
TV
SELECT
3
SET : SET
SET UP TV
CAPT I ON
I NPUT SELECT
: TUNER
SET UP V I DEO / AUD I O
DVD VOL ADJUST : + 2
FM ANTENNA
: I NT
SET : SET
SELECT :
END
: ACT I ON
4
CAPT I ON
CAPT I ON MODE
CC ON MUTE
1) Press
to select
“CAPTION.”
2) Press SET to display
CAPTION screen.
: OFF
: CAP C1
1) Press
to select
CAPTION MODE.
2) Press SET repeatedly
to select “OFF.”
TV Operation
SET
CH
CLOCK
SELECT :
END
: ACT I ON
ACTION
1
1) Press
to select
“TV.”
2) Press SET to display
SET UP TV screen.
SELECT :
SET
: SET
END
: ACT I ON
1) Press
to select
CC ON MUTE.
2) Press SET repeatedly
to select desired mode.
5
NO
CAP C1
• Each press of SET will
change the display as shown
left.
• The caption may be broadcast
over CAP C1 or C2.
CAP C2
Note
• When a disc supporting closed caption is
used, the subtitle and the closed caption
may overlap. In this case, turn the subtitle or
caption on mute mode off. (See page 46.)
6
Press ACTION three times to return to the normal
screen.
7
Press MUTE to mute the sound and display
closed captioning.
• To cancel, press MUTE again.
25
TV Timer Features
ON-TIMER with Alarm
Check List
The clock is set to the correct time.
This unit can be set to automatically power on in one of
4 modes (TV, VCR Playback, FM radio, or DVD/Video
CD/CD.) You can also combine the On-Timer with a
one minute alarm that gradually increases in volume.
1
2
Press PROG* to display SET PROGRAM
screen.
SET PROGRAM
T I MER PROGRAMM I NG
ON T I MER
SLEEP T I MER : 00
SELECT :
SET
: SET
END
: PROG
3
1) Press
to select
desired settings.
2) Press SET to set
the ON-TIMER
time or ON-TIMER
mode.
ON T I MER
ALARM : ON
SELE CT HOUR
SELECT :
SET
: SET
END
: PROG
• ON-TIMER mode
selection order
CH02
CH03
CH125
CH01
VCR
DVD
4
FM9
FM8
FM1
• Make sure a tape is
inserted if Playback
mode is selected.
• Make sure a disc
is inserted if DVD
(DVD/Video CD/CD)
mode is selected.
• See “FM Radio” on pages
28 and 29 for instructions
on how to preset FM
stations.
Press
to select
ALARM “ON” or
“OFF.”
ON T I MER
ALARM : ON
SELE CT ALARM
CANCEL : ADD / DLT
SELECT :
SET
: SET
END
: PROG
1) Press
to select
“ON TIMER.”
2) Press SET to
display ON TIMER
screen.
BACK :
When “ON” is selected,
an alarm will gradually increase in volume for one
minute or until canceled by pressing any button
(including VOL + -).
To Make Corrections,
and
to move back and correct.
use
5
Press PROG to set ON TIMER.
• “ON TIMER SET” is displayed.
• ON-TIMER Indicator lights up on the unit.
To Cancel ON-TIMER,
Repeat steps 1 and 2. Then, press ADD/DLT to clear
the time in step 3. Now, press PROG to end.
“ON TIMER END” briefly appears on-screen.
26
ON-TIMER Indicator
Sleep Timer
This unit can be set for auto power off.
1
Press PROG to display SET
PROGRAM screen.
2
1) Press
to
select SLEEP
TIMER.
2) Press SET
repeatedly to
select the
desired time.
SET PROGRAM
T I MER PROGRAMM I NG
ON T I MER
SLEEP T I MER : 00
SELECT :
SET
: SET
END
: PROG
SLEEP TIMER 30
60
90
00
To cancel,
press SET repeatedly until 00 appears.
3
Press PROG to return to the normal
screen.
• Pressing DISPLAY with sleep timer set
displays remaining time.
Note
• If no button on the remote or unit (including a
button used to turn off the alarm) is pressed
within 60 minutes after unit turns itself on, it will
turn itself back off.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
On-Screen Display (OSD)
*Important:
If a remote control button does not work when pressed, press the TV/VCR button on the remote
and try the button again.
TV/VCR Status & Clock Display
Press DISPLAY to display or remove the overlay.
Function Status
Rec Time
Remaining
(OTR mode
only, see page
18.)
DISPLAY
Current Time
CH08
REC
1 2 : 0 0PM
-0 : 1 2 : 3 4
0 : 25
SP
STEREO
SAP
MONO
Receivable
Broadcast
Types (See
page 23.)
Counter
Tape
Speed
(See
page 4.)
SELECT
SET
Blue Screen Display
TV Operation
ADD/DLT
Channel
Whenever a blank section of a tape comes up in Playback
mode, or when the selected channel has no broadcast signal
with the Weak Signal Display Feature set to “OFF” (see page
36), the screen will turn solid blue.
PROG
Channel & Function Display
When a function button is pressed (PLAY, FF, etc.) or you change
channels, the unit mode or channel number will be displayed.
CH08
PLAY
27
FM Radio
FM Radio is ...
This unit has an FM radio with built-in antenna, 9 station preset, and a band range of 87.5 ~ 108.1 MHz.
You can set the On-Timer (page 26) to wake up to your favorite radio station.
FM Radio Setup
1
Press FM* on the remote or TV/FM on the
unit to display FM radio mode.
2
1 2 : 0 0PM
3
1 2 : 0 0PM
FM 1
FM 1
Press a NUMBER
key (1~9) to select the
FM preset number.
87. 5MHz
8 7. 7MHz
MEMORY : PRESS ADD / DLT KEY
1 2 : 0 0PM
FM 1
1) Press CH
to
select the desired
radio station. (Each
press changes
frequency by 200
kHz.)
2) Press ADD/DLT
to set the
radio station.
TV/FM
8 7. 7MHz
Hold down CH
or
for a few seconds, then
release to quickly scan
for FM stations in your
To Make Corrections, select area.
station with a NUMBER
• To cancel, press CH
or while in search
keys, then do step 3 again.
MEMOR I ZED
mode.
To exit FM mode, press
TV/VCR or DVD on the
remote or TV/FM on the
unit.
CH
FM Antenna Setup
Make sure FM tuning is done correctly (see FM
Radio Setup).
1
2
Press ACTION to display MAIN MENU.
M A I N MENU
DVD
LOCK LANGUAGE
53
TV
CLOCK
SELECT :
END
: ACT I ON
1
CH
1) Press
to
select “TV.”
2) Press SET to
display SET UP TV
screen.
SET : SET
Continued on next page.
28
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
*Important: If a remote control button does not work when pressed, press the FM button on the
remote and try the button again.
3
SET UP TV
CAPT I ON
I NPUT SELECT
: TUNER
SET UP V I DEO / AUD I O
DVD VOL ADJUST : + 2
FM ANTENNA
: I NT
SELECT :
END
: ACT I ON
SET : SET
TV/VCR
■ For cable TV users
➞ “INT”
■ For antenna users
➞ “EXT”
DVD
DISPLAY
NUMBER
keys
FM
ADD/DLT
ACTION
4
1) Press
to select
FM ANTENNA.
2) Press SET
to select “INT
(INTERNAL)”
or “EXT
(EXTERNAL)” to
determine which
one sounds best.
Press ACTION twice to end setup.
SELECT
Using FM Radio
AUDIO
1
2
Press FM on the remote or TV/FM on the
unit to display FM radio mode.
1 2 : 0 0PM
FM 1
87. 5MHz
TV Operation
SET
CH
Press a NUMBER
key (1~9) to select
a preset FM number
(see FM Radio Setup
on page 28).
To exit FM mode,
press TV/VCR or DVD on the remote or
TV/FM on the unit.
Notes
• FM radio cannot be recorded on a Video
cassette.
• You may get better reception by
repositioning the unit.
• You cannot select FM Radio mode during
playback or record, or while a blue back
screen (PROG, ACTION, MENU) is
displayed.
• Once stations are set, the selected station
and current time are displayed when FM
Radio mode is entered. To remove time,
press DISPLAY. If DISPLAY is pressed
again, the unit status screen appears.
Audio Mode for FM Radio
1 2 : 0 0PM
STEREO
MONO
FM 1
8 7. 7MHz
Press AUDIO
repeatedly to select
“STEREO” or “MONO”
in FM Radio mode.
29
Timer Recording
You can set up to 8 programs to be recorded while you
are away.
1
2
Press PROG* to display SET PROGRAM
screen.
1) Press
to select
TIMER
PROGRAMMING.
2) Press SET to
display screen.
SET PROGRAM
T I MER PROGRAMM I NG
ON T I MER
SLEEP T I MER : 00
SELECT :
SET
: SET
END
: PROG
• If a program is already in memory, press
SET to select an unused program number.
3
DATE
START
STOP
CH
Check List
Cable or antenna is connected.
Power cord is plugged in.
The clock is set to correct time.
The tape is long enough.
The record tab is in place.
, and
Press
to select
to set
the recording DATE.
7 FR I --:-- --:-- -- and SET or
TODAY
SP
-----------------------SELE CT START DATE
SELECT :
SET
: SET
: PROG
END
• 1~31 = One time
• DAILY = MON~FRI
• WEEKLY SUN~SAT
= Same time once a week
Example
8
Today’s
Date
9
31
SELECT
7
/
WEEKLY
(SAT)
1
2
6
Selection Order
WEEKLY
(MON)
DAILY
WEEKLY
(SUN)
Repeat step 3 to set:
• Start time, Stop time
• Channel (or LINE for outside source)
• Speed (SP, LP, SLP)
4
P
1
2
3
4
DT
day
----
START
9 : 00 p
-- : --- : --- : --
STOP
12 : 00a
-- : --- : --- : --
CANCEL : ADD / DLT
SELECT 1 - 8 :
ENTER : SET
END
: PROG
5
30
CH SPD
08 SP
-- --- --- --
PROG TIMER Indicator
Press PROG to end
the program.
To Enter More
Programs,
to select
press
and SET to set a
blank program
number, and then
repeat step 3.
Press PROG twice to exit this mode.
• If you’re using a cable box, make sure that it is tuned
to the desired channel and the power is left on for
timer recording.
• PROG TIMER Indicator lights up on the unit.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
*Important: If a remote control button does not work when pressed, press the TV/VCR button on
the remote and try the button again.
Cancel a Timer Recording:
(Recording is in progress)
Hold down STOP for a few
seconds to cancel the Timer
Recording.
• Any future daily or weekly recordings will
be performed as programmed.
Review, Replace or Clear
Program Contents :
(Recording is not in progress)
1
Repeat steps 1 and 2 on page 30.
Press
to select
the desired program.
2
CANCEL : ADD / DLT
SELECT 1 - 8 :
ENTER : SET
END
: PROG
ADD/DLT
3
To Replace program...
DATE
START
STOP
CH
SET
1) Press SET to
display.
SLP
to select
------------------------ 2) Press
SELE CT START DATE
and
press
SET
SELECT :
to set new
or
SET
: SET
BACK :
END
: PROG
program contents.
3) Press PROG.
STOP
To Clear program...
8 SAT 9:00P 12:00A 08
SELECT
TODAY
PROG
DT START STOP CH SPD
-- -- : -- -- : -- -- -8 10 : 00p 12 : 00a 125 SP
10 8 : 00p 9 : 00p 10 SP
SU 9 : 00p 10 : 00p L LP
Press ADD/DLT.
SELECT 1 - 8 :
ENTER : SET
END
: PROG
4
Timer Operation
P
1
2
3
4
Press PROG twice to exit this mode.
Notes
• 2 minutes before Timer recording is performed, “PLEASE
PREPARE FOR TIMER REC” appears and/or the PROG
TIMER Indicator flashes. Be sure a cassette with record
tab is loaded and the unit is in Stop mode.
• If the start times of two programs overlap, the lower
numbered program will have priority.
• If the start time for a Timer Recording comes up during a
normal recording or One Touch Recording (page 18), the
Timer Recording will not be performed.
• If there is a power interruption of more than one minute,
the recording may not be performed or continued.
• If “INCOMPLETE” appears after all items have been set,
check all entries and make necessary corrections.
31
Tape Operation
Search System is ...
Each time a recording is made, an invisible index mark is placed on the tape. When timer recordings are
made, program index and information are also included. These index marks can be used to access or
scan recordings.
Index Search
Go directly to the desired recording.
1
I NDEX SEARCH
ENTER I NDEX NUMBER : 1
US I NG 1- 9 KEYS
FORWARD SEARCH : FF
REVERSE SEARCH : REW
EX I T : SEARCH
Press SEARCH*
in Playback or
Stop mode to
display INDEX
SEARCH screen,
and then press
NUMBER keys
to select the
recording number.
• To calculate
number, see below.
Press FF or REW to start search.
2
REW
FF
Playback begins
at search end. To
search forward
or back 1 index,
press FF or REW
while screen left
is displayed (10
seconds).
I NDEX SEARCH
FORWARD SEARCH : FF
REVERSE SEARCH : REW
NUMBER
keys
SELECT
To cancel, press PLAY.
SET
REW
FF
■ To calculate the Index Number
SEARCH
Example 1:
To go to rec. 2 from rec. 4, enter 3 and press REW.
1
2
3
4
5
6
7
Example 2:
To go to rec. 6 from rec. 2, enter 4 and press FF.
1
2
3
4
5
6
7
Note
• If Index Search is started very close to an index
mark, that index mark may not be counted in
the search.
NOTE: indicates start points of each recording.
32
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
*Important: If a remote control button does not work when pressed, press the TV/VCR button on the
remote and try the button again.
Repeat Play
Set to see a recording over and over.
PLAY
REPEAT ON
To turn “ON,”
press PLAY/REPEAT on the unit repeatedly
in Playback mode to select “REPEAT ON.”
To turn “OFF,”
repeat above to select “REPEAT OFF.”
• Playback repeats when tape end is reached or
an unrecorded portion longer than 30 seconds is
detected.
PLAY/REPEAT
Note
• For repeat play in DVD mode, see page 53.
Advanced Operation
33
Tape Operation (continued)
Zero Search
To quickly return to a specific tape counter
location.
1
2
Press DISPLAY* during playback to
display the Counter.
PLAY 12 : 00 PM
0 : 00 : 00
SLP
Press COUNTER
RESET at the
desired position to
reset to “0:00:00.”
3
Continue playback, rewind, or fast
forward.
4
Press STOP.
DISPLAY
STOP
CM/ZERO
5
Press CM/ZERO in stop mode to start
ZERO SEARCH.
• Unit goes into FF or REW mode and stops at the
last point the Counter was set to 0:00:00.
34
COUNTER
RESET
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
*Important: If a remote control button does not work when pressed, press the TV/VCR button on the
remote and try the button again.
Auto Operation Functions
■ Auto Shut Off
No broadcast signal in TV mode (Only when Weak Signal
Display is set to OFF.), DVD stops, or blank tape is played
for 5 minutes.
➞ Power turns off
• This feature is canceled if any button is pressed during above
conditions.
■ Auto Playback
Insert a tape in Power off mode
➞ Power turns on
• Playback begins if tape has no record tab.
■ Auto Rewind (except for Recording)
Tape reaches its end
➞ Rewind, ➞ Stop
■ Playback Auto Eject (Repeat Play is “OFF”)
Tape with no record tab reaches its end
➞ Rewind, ➞ Stop, ➞ Eject
Commercial Skip
By pressing the CM/ZERO button in Playback mode you
can skip over 1 to 3 minutes of recorded tape in just a few
seconds.
Press CM/ZERO repeatedly to select skip time in
Playback mode.
• No indication appears.
1st Press
1 min skip
2nd Press
2 min skip
3rd Press
3 min skip
Advanced Operation
OFF
35
Special VCR Features
Weak Signal Display Feature
Check List
It is necessary to enter TV
mode by pressing TV/VCR
before selecting “CH” on the
MAIN MENU.
When “ON” is selected, the picture is displayed
even when a broadcast signal is weak or
non-existent.
1
Press ACTION* to display MAIN MENU.
2
M A I N MENU
DVD
LOCK LANGUAGE
53
TV
CLOCK
SELECT :
END
: ACT I ON
1
CH
SET : SET
1) Press
to select “CH.”
2) Press SET to
display SET
UP CHANNEL
screen.
ADD/DLT
ACTION
3
SET UP CHANNEL
ANTENNA : CABLE
AUTO SET
WEAK S I GNAL D I SPLAY : OFF
SELECT :
SET
: SET
END
: ACT I ON
1) Press
to
select WEAK
SIGNAL
DISPLAY.
2) Press SET
to set “ON” or
“OFF.”
SELECT
SET
Notes
• “ON” = Picture is displayed regardless of signal
condition, and may not always be clearly
visible.
“OFF” = Screen turns solid blue when signal is absent
or weak.
• If unit is connected to equipment which has blue back
feature, selecting “ON” will have no effect on the other
equipment.
4
36
Press ACTION twice to return to the
normal screen.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
*Important: If a remote control button does not work when pressed, press the TV/VCR button on
the remote and try the button again.
VCR Lock
All operations are prohibited except Timer
recording and tape eject. Useful for families with
small children.
VCR LOCK ACT I VATED
In Stop mode, hold
down REC on
the unit without a
cassette inserted for 7
seconds to turn “ON.”
(Please ignore “NO
CASSETTE” warning.)
Repeat above with or
without cassette to turn
“OFF.”
VCR LOCK OFF
REC
• VCR Lock is canceled automatically after about 24
hours if clock is set.
Advanced Operation
37
V-Chip Control Feature
V-Chip Control Feature is...
Process of V-Chip Control Feature
This unit has a built-in V-Chip Control which allows you
to block unwanted TV usage based on US MOVIES and
US TV PROGRAMS Ratings.
Enter Code
Setup
Blocking
Enter Secret Code
A 4-digit code must be entered to view a blocked
program or change rating settings.
1
Press ACTION* to display MAIN MENU.
2
M A I N MENU
DVD
LOCK LANGUAGE
53
TV
CLOCK
SELECT :
END
: ACT I ON
3
1
CH
1) Press
to
select “LOCK.”
2) Press SET to
display LOCK
screen.
NUMBER
key
ACTION
SET : SET
LOCK
ENTER 4-D I G I T CODE
-BACK SPACE:
ENTER : 0 - 9
END
: ACT I ON
CLEAR
SELECT
1) Press NUMBER
keys to enter your
secret code.
2) Enter same
code again for
confirmation.
SET
• Step 2) not necessary when changing rating or
secret code.
• Take care that you are not observed entering the
secret code.
To Make Corrections
Press repeatedly to move the cursor.
Press NUMBER keys to make the correction.
4
LOCK
CONF I RM 4-D I G I T CODE
****
****
RECOGN I ZED
CHANGE CODE : ADD / DLT
CONT I NUE : SET
END
: ACT I ON
Press SET to display
US Ratings menu
(see pages 39-40).
Or
Press ACTION twice
to exit.
Changing your secret code
• You will need your current code.
Do steps 1 ~ 3. In step 4, press CLEAR to clear
current code.
Repeat steps 3 and 4 to enter new code.
38
Notes
• Some rental movies do not include V-Chip
data.
• DO NOT forget your secret code.
• Once ratings are set, restricted tapes or
programs cannot be accessed unless the
secret code is entered.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
*Important: If a remote control button does not work when pressed, press the TV/VCR button on the
remote and try the button again.
If LOCK menu is not displayed, perform “Enter
Secret Code” steps on page 38.
US MOVIES Ratings
1
LOCK
US MOV I ES
: OFF
CHANGE SETT I NGS
: OFF
US TV PROGRAMS
CHANGE SETT I NGS
DVD LOCK
: OFF
CHANGE SETT I NGS
NEXT PAGE
SELECT :
SET : SET
END
: ACT I ON
1) Press
to select
US MOVIES.
2) Press SET to set
“ON” or “OFF.”
• “NEXT PAGE” displays CANADIAN V-Chip
setting menu. Not necessary except when viewing
Canadian tapes or broadcasts.
LOCK
US MOV I ES
: OFF
CHANGE SETT I NGS
US TV PROGRAMS
: OFF
CHANGE SETT I NGS
DVD LOCK
: OFF
CHANGE SETT I NGS
NEXT PAGE
SELECT :
SET : SET
END
: ACT I ON
1) Press
to
select CHANGE
SETTINGS.
2) Press SET to
display screen.
Setup
Blocking
US MOVIES RATINGS
G
GENERAL AUDIENCE:
All ages admitted.
PARENTAL GUIDANCE:
Some material may not be suitable
for children.
PARENTS CAUTIONED:
PG-13 Some material may be inappropriate
for children under 13.
R
NC-17
X
RESTRICTED:
Children under 17 must be
accompanied by a parent or adult.
OVER AGE 17 ONLY:
No one 17 and under admitted.
ADULTS ONLY:
1) Press
to
select VIEW NR
PROGRAMS?.
2) Press SET to set
“YES” or “NO.”
3
Press
to select
and SET to set
ratings to be blocked.
(See ratings chart on
this page.)
4
Advanced Operation
NR (Not Rated) PROGRAMS
Some movies, such as old movies or foreign
movies usually have no ratings.
5
Enter Code
PG
■ “ON” ➞ V-Chip Control is activated.
■ “OFF” ➞ V-Chip Control is deactivated.
Note
2
Process of V-Chip Control Feature
Press ACTION to redisplay LOCK
menu and continue with US TV
PROGRAMS Ratings Setup (page 40).
Or,
press ACTION three times to exit.
39
V-Chip Control Feature (continued)
If LOCK menu is not displayed, do “Enter
Secret Code” steps on page 38.
Process of V-Chip Control Feature
US TV PROGRAMS Ratings
US TV PROGRAMS RATINGS: Chart 1
1
LOCK
US MOV I ES
: OFF
CHANGE SETT I NGS
US TV PROGRAMS
: OFF
CHANGE SETT I NGS
DVD LOCK
: OFF
CHANGE SETT I NGS
NEXT PAGE
SELECT :
SET : SET
END
: ACT I ON
1) Press
* to
select US TV
PROGRAMS.
2) Press SET to set
“ON” or “OFF.”
■ “ON” ➞ V-Chip Control is activated.
■ “OFF” ➞ V-Chip Control is deactivated.
Note
• “NEXT PAGE” displays CANADIAN V-Chip setting
menu. Not necessary except when viewing Canadian
tapes or broadcasts.
2
3
LOCK
US MOV I ES
: OFF
CHANGE SETT I NGS
US TV PROGRAMS
: OFF
CHANGE SETT I NGS
DVD LOCK
: OFF
CHANGE SETT I NGS
NEXT PAGE
SELECT :
SET : SET
END
: ACT I ON
V I EW NR PROGRAMS? : YES
UNLOCKED
TV-Y
FV
TV-Y7
TV-G
V S L D
TV-PG
V S L D
TV-1 4
V S L
TV-MA
CONTA I NS NO RAT I NG
SELECT :
SET : SET
END
: ACT I ON
1) Press
to
select CHANGE
SETTINGS.
2) Press SET to
display screen.
1) Press
to
select VIEW NR
PROGRAMS?.
2) Press SET to set
“YES” or “NO.”
NR (Not Rated) PROGRAMS
Some TV shows, such as news, sports, weather,
bulletins, emergency information usually have no
ratings.
4
V I EW NR PROGRAMS? : YES
UNLOCKED
TV-Y
FV
TV-Y7
TV-G
V S L D
TV-PG
V S L D
TV-1 4
V S L
TV-MA
FOR ALL CH I LDREN
SELECT :
SET : SET
END
: ACT I ON
Press
to select
and SET to set
ratings to be blocked.
(See ratings charts on
this page.)
• Ratings highlighted in
green will be blocked.
Ratings in white letters
will not be blocked.
Note
• You may select from standard TV ratings (chart 1), or
customize to a specific content rating (chart 2).
5
40
Enter Code
Setup
Blocking
TV-Y FOR ALL CHILDREN:
Content specifically geared to young
viewers ages 2-6.
TV-Y7 FOR AGE 7 AND OLDER:
May contain mild physical or comedic
violence which may frighten children
under 7.
TV-G GENERAL AUDIENCE:
Contains little or no violence, strong
language, or sexual dialogue or
situations.
TV-PG PARENTAL GUIDANCE:
May contain infrequent coarse
language, limited violence, some
suggestive sexual dialogue and
situations.
TV-14 PARENTS CAUTIONED:
May contain sophisticated themes,
sexual situations, strong language,
and more intense violence.
TV-MA MATURE AUDIENCE:
May contain mature themes, profane
language, graphic violence, and
sexual situations.
US TV PROGRAMS RATINGS: Chart 2
FV
Fantasy Violence
V
Violence
S
Sexual Situations
L
Adult Language
D
Sexually Suggestive Dialogue
Press ACTION three times to exit this mode.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
*Important: If a remote control button does not work when pressed, press the TV/VCR button on the
remote and try the button again.
Process of V-Chip Control Feature
Enter Code
Setup
Blocking
Blocking Message
<When V-Chip Control is activated>
CH08
DISPLAY
PROGRAM RAT I NG EXCEEDED
RAT I NG : PG-1 3
ACCESS CODE
----
• If a program or movie
exceeds the ratings you
have set, a message
will appear on a black
background and sound is
muted.
ENTER : 0-9
ACTION
SELECT
SET
To View a Blocked Program/Movie
[Temporarily Deactivate V-Chip Control]
Enter your secret code (ACCESS CODE) in the
Blocking Message screen.
• V-Chip Control is reactivated when power is turned off
or power failure occurs.
[Deactivate V-Chip Control]
Enter your secret code (steps 1-3 page 38). Then,
set US MOVIES and/or US TV PROGRAMS to
and SET. (Ratings set on pages
“OFF” using
39 and 40 is retained and will be in effect when
V-Chip Control is activated again.)
Advanced Operation
41
Audio Features
Audio Mode for Playback
Choose the type of sound track for playback.
1
2
See the “Playback a Tape” section on page
18 to playback the tape.
H I F I ( L/R)
H I F I ( L)
H I F I ( R)
NORMAL
Press AUDIO*
repeatedly (each press
within 5 seconds) to
select desired mode.
With the proper audio mode
setting, your unit can:
• Record and playback MTS stereo broadcast
(main language) in stereo Hi-Fi. Stereo sound is
recorded on the left and right audio tracks and
on the video portion of a tape.
• Record and playback a monaural broadcast
(main language) or SAP (Secondary Audio
Program, usually in a second language) on the
Hi-Fi tracks for better quality monaural sound.
• Playback non-Hi-Fi tapes in monaural.
• Select “HIFI (L/R),” “HIFI
(L)” or “HIFI (R)” to listen
to stereo recordings in
stereo sound. Select
“NORMAL” for monaural
sound.
• This screen appears when you press AUDIO during
playback.
Audio Mode for Recording
Choose audio mode to match recording type.
1
Press AUDIO repeatedly to select the audio
mode according to the type of broadcast to be
recorded.
• The Audio mode selected stays in effect until it is
changed.
2
MUTE
ACTION
SELECT
SET
VOL+/-
See the “Record On a Tape” section on page
18 to do a recording.
AUDIO
Notes
• Only tapes recorded in Hi-Fi stereo will playback with true
stereo sound. Standard stereo tapes will playback with
monaural sound.
• To listen to Hi-Fi stereo playback, the unit AUDIO (L/R)
jacks must be connected to a stereo amp and speakers.
• There may be a difference in audio level between Hi-Fi
and normal audio playback.
42
SURROUND/
VSS
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
*Important: If a remote control button does not work when pressed, press the TV/VCR button on the
remote and try the button again.
DVD Volume Adjust
Some DVDs are recorded in lower average volume
level. For these DVDs, this unit can be set so that
the average volume is increased automatically.
1
2
Press ACTION* to display MAIN MENU.
M A I N MENU
LOCK LANGUAGE
DVD
53
TV
1
CH
CLOCK
SELECT :
END
: ACT I ON
1) Press
to select “TV.”
2) Press SET to
display SET UP
TV screen.
V.S.S. (Virtual Surround Sound)
[DVD only]
Enjoy a surround-like effect if you are using two
front speakers only. The effect is broadened
and sound seems to come from virtual speakers
on either side if the disc has surround signals
recorded on it.
Press VSS in DVD mode.
• The Surround sound effects can be changed by
pressing VSS repeatedly as shown by the figure
below.
SET : SET
VSS OFF
3
SET UP TV
CAPT I ON
I NPUT SELECT
: TUNER
SET UP V I DEO / AUD I O
DVD VOL ADJUST : + 2
FM ANTENNA
: I NT
SELECT :
END
: ACT I ON
4
SET : SET
1) Press
to
select DVD
VOL ADJUST.
2) Press SET to
set the level (0,
+1, or +2).
Default
VSS1
Press ACTION twice to return to the
normal screen.
VSS2
Surround Sound System
VSS3
SURROUND ON
SURROUND OFF
Press SURROUND.
• “SURROUND ON” is
displayed.
To Cancel,
press SURROUND.
Notes
Advanced Operation
You can hear a deeper, 3-D sound effect using
just the unit’s two front speakers.
• V.S.S. effects is available in DVD mode only.
• Turn off the surround effects on the other equipment.
• V.S.S. will not work, or will have less effect, with some
discs.
• Turn V.S.S. off if it causes distortion.
Notes
• Surround sound effect is not available for normal
(mono) broadcasts.
• The surround effect (TV, VCR mode only) is not
output to Audio Output L/R Connector.
43
Video/Audio Menu
This feature allows easy setting of picture and sound suitable for each program source.
Audio Menu
Video Menu
1
2
Press ACTION* to display MAIN MENU.
M A I N MENU
LOCK LANGUAGE
DVD
53
TV
SELECT :
END
: ACT I ON
3
1
CH
CLOCK
1) Press
to
select “SET UP
VIDEO/AUDIO.”
2) Press SET to
display.
SET UP TV
4
SET : SET
SET UP V I DEO / AUD I O
V I DEO
V I DEO
AUD I O
AUD I O
MENU
: NORMAL
ADJUST
MENU
: MUS I C
ADJUST
SELECT :
SET
: SET
END
: ACT I ON
1) Press
to
select “VIDEO
MENU.”
2) Press SET
repeatedly to
select desired
mode. (See
below.)
Do steps 1-3 left.
SET UP V I DEO / AUD I O
V I DEO
V I DEO
AUD I O
AUD I O
MENU
: NORMAL
ADJUST
MENU
: MUS I C
ADJUST
SELECT :
SET
: SET
END
: ACT I ON
SET : SET
CAPT I ON
I NPUT SELECT
: TUNER
SET UP V I DEO / AUD I O
DVD VOL ADJUST : + 2
FM ANTENNA
: I NT
SELECT :
END
: ACT I ON
1) Press
to select “TV.”
2) Press SET to
display SET
UP TV screen.
a
b
c
1) Press
to
select “AUDIO
MENU.”
2) Press SET to
select desired
mode. (See
below.)
Press ACTION three times to end setup.
[Audio Menu]
■ NORMAL
■ AUTO
[Audio AGC (Auto Gain Control)]
The sound level is automatically adjusted to suit
the program source (see below left).
■ MOVIE
Sound suited to movies.
■ MUSIC
Sound suited to music. (Factory setting)
■ SPEECH
5
Press ACTION three times to end setup.
Sound suited to dialogue.
[Video Menu]
■ NORMAL
Factory setting.
ACTION
■ MOVIE
Picture is adjusted for a movie-like feel.
■ NIGHT
SELECT
Color and picture intensity are adjusted to be
easier on the eyes for night viewing.
Volume level
High
Standard
TV
Volume level
High
CD
TV
Low
Standard
TV
TV
AUDIO MENU : AUTO
<Audio AGC Example>
44
Notes
CD
Low
AUDIO MENU : NORMAL
SET
• The effects of this feature on the signal is not output
to the Audio/Video Output Connector.
• When AUDIO MENU mode is “AUTO,” the AUDIO
ADJUST setting will be “STANDARD.”
• AUDIO MENU settings remain in memory.
• VIDEO MENU settings do not remain in memory.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Video/Audio Adjustment
*Important: If a remote control button does not work when pressed, press the TV/VCR button on the
remote and try the button again.
Audio Adjustment
Video Adjustment
1
2
Press ACTION to display MAIN MENU.
M A I N MENU
DVD
LOCK LANGUAGE
53
TV
SELECT :
END
: ACT I ON
3
SET UP TV
MENU
: NORMAL
ADJUST
MENU
: MUS I C
ADJUST
SELECT :
SET
: SET
END
: ACT I ON
5
V I DEO ADJUST
COLOR
T I NT
BR I GHTNESS
P I CTURE
SHARPNESS
STANDARD
SELECT :
ADJUST :
END
: ACT I ON
DVD
LOCK LANGUAGE
1) Press
to
select “SET UP
VIDEO/AUDIO.”
2) Press SET to
display.
c
d
SET UP TV
1) Press
to
select an item.
(See below.)
to
2) Press
adjust.
e
MENU
: NORMAL
ADJUST
MENU
: MUS I C
ADJUST
SELECT :
SET
: SET
END
: ACT I ON
AUDIO ADJUST
BASS
TREBLE
BALANCE
STANDARD
SELECT :
ADJUST :
END
: ACT I ON
f
Press ACTION four times to end setup.
[AUDIO Adjustment]
■ COLOR Control
■ BASS Control
■ TINT Control
Adjust for natural flesh tones.
■ BRIGHTNESS Control
Adjust picture brightness.
■ PICTURE Control
Adjust picture intensity by adjusting both
contrast and color level in the proper balance.
1) Press
to
select an item.
(See below.)
to
2) Press
adjust.
To Reset AUDIO Controls,
and SET to select and set
press
“STANDARD.” All controls return to their factory
settings.
[VIDEO Adjustment]
Adjust color intensity.
1) Press
to
select “AUDIO
ADJUST.”
2) Press SET to
display.
Advanced Operation
Press ACTION four times to end setup.
1) Press
to
select “SET UP
VIDEO/AUDIO.”
2) Press SET to
display.
SET : SET
SET UP V I DEO / AUD I O
V I DEO
V I DEO
AUD I O
AUD I O
1) Press
to select “TV.”
2) Press SET to
display SET UP
TV screen.
SET : SET
CAPT I ON
I NPUT SELECT
: TUNER
SET UP V I DEO / AUD I O
DVD VOL ADJUST : + 2
FM ANTENNA
: I NT
SELECT :
END
: ACT I ON
1) Press
to
select “VIDEO
ADJUST.”
2) Press SET to
display.
1
CH
CLOCK
SELECT :
END
: ACT I ON
To Reset VIDEO Controls,
and SET to select and set
press
“STANDARD.” All controls return to their factory
settings.
6
M A I N MENU
53
SET : SET
SET UP V I DEO / AUD I O
V I DEO
V I DEO
AUD I O
AUD I O
Press ACTION to display MAIN MENU.
TV
SET : SET
CAPT I ON
I NPUT SELECT
: TUNER
SET UP V I DEO / AUD I O
DVD VOL ADJUST : + 2
FM ANTENNA
: I NT
SELECT :
END
: ACT I ON
4
1
CH
CLOCK
1) Press
to select “TV.”
2) Press SET to
display SET
UP TV screen.
a
b
To adjust the intensity of low frequency sound.
■ TREBLE Control
To adjust the intensity of high frequency sound.
■ BALANCE Control
To adjust the (L/R) unit speaker output level.
• The levels set here do not affect other audio
equipment when connected to the Audio Output
L/R Connector.
■ SHARPNESS Control
Adjust picture sharpness.
45
Disc Operation
Subtitle Language (DVD only)
You can select a different subtitle language (if offered)
than the one set at the Settings for DVD Operation. (See
page 58.)
Press SUB TITLE* in
Play mode to display
the subtitle selection
on-screen.
1
Check List
Please read “Basic DVD Operation” on
page 20.
[Subtitle language]
[Audio soundtrack language]
ENG
FRA
DEU
ITA
ESP
NLD
SVE
NOR
DAN
POR
RUS
JPN
CHI
KOR
MAL
VIE
THA
• Display disappears
after 5 seconds.
• When no subtitles
are offered, “-” will be
displayed instead of
the language number.
2
Te amo
1) Press
to select
desired language.
2) Press (or )
to select “ON” or
“OFF.”
Number of subtitle language being played back.
Notes
• When closed captioning is used along with subtitles, they may
overlap. If so, turn one function off. (See pages 24 and 25.)
• If after several presses of the button the language does not
change, language selection is not offered on the disc.
• Subtitles may not change to the selected language
immediately.
• When disc is removed, subtitles revert to initial setting
language. If the initial language is not recorded on the disc,
the disc’s priority language will appear.
English
French
German
Italian
Spanish
Dutch
Swedish
Norwegian
Danish
Portuguese
Russian
Japanese
Chinese
Korean
Malay
Vietnamese
Thai
Other
• Change the No. by pressing
SET.
, and press
Audio Soundtrack Language (DVD only)
You can change the audio soundtrack language,
selected at the Settings for DVD Operation, to a
different language if available. (See page 58.)
(This operation works only with discs on which multiple
audio soundtrack languages are recorded.)
a
AUDIO: 1 ENG
Dolby Digital 3/2.1ch
Hello
SELECT :
END
: AUDIO
Press AUDIO in
Play mode to display
the audio selection
on-screen.
• Display disappears after
5 seconds.
Audio attribute 1 type,
sampling frequency, bit
No. of the disc.
b
AUDIO: 3 ESP
Dolby Digital 3/2.1ch
Press
to select
desired language.
Hola
SELECT :
END
: AUDIO
46
Audio soundtrack
language being played
back.
[Audio attribute 1 type, sampling
frequency, bit No. of the disc (see
page 59)]
96 kHz
LPCM
or
48 kHz
16 bit
20 bit Linear PCM disc
24 bit
Dolby
Digital
1 ch - 5.1 ch
Dolby Digital disc
dts
1 ch - 5.1 ch
dts disc
Notes
• If, after several presses of the AUDIO button the
language does not change, language selection is
not offered on the disc.
• When disc is removed, language reverts to initial
setting. If this language is not recorded on the disc,
the language recorded will be heard.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
*Important: If a remote control button does not work when pressed, press the DVD button on the
remote and try the button again.
appears on the screen while a
When
button is being pressed, it means that the
corresponding operation is prohibited by
the unit or the disc.
Multiple Angle Viewing (DVD only)
DVDs may contain scenes shot from multiple camera
angles allowing the same scene to be viewed at different
angles. You can view these angles, if available, using the
ANGLE button.
Press ANGLE in Play
mode to display the angle
selection on-screen.
1
• Display disappears after 5
seconds.
ANGLE Indicator
Press
to select the
desired angle.
2
Notes
• ANGLE Indicator lights up on the unit when
a scene recorded at different angles is
detected.
• The angle number can be set beforehand
so that the angle is switched whenever
ANGLE Indicator lights up.
SELECT
SET
Number of angle being played back.
Vocal selection for Karaoke discs (DVD/Video CD)
a
b
Press AUDIO in Play mode to display the audio
screen.
1) Press
(or
) to
select as shown below.
2) Press (or ) to set.
(DVD only)
SELECT :
END
: AUDIO
ANGLE
• Video CD
LR
L
R
ZOOM
AUDIO
Notes
• Closed captioning will not be displayed
while Picture Zoom is used. To see
subtitles, set the subtitle feature to ON (see
page 46).
• The subtitle cannot be enlarged nor can it’s
position be changed.
• The picture zoom feature does not work
with a Video CD.
• During picture zoom, “ZOOM1” or “ZOOM2”
appears on-screen for 5 second.
• Zooming, on some discs, may result in poor
picture quality, or may not operate at all.
Picture Zoom (DVD only)
You can enlarge specific portions of a picture and select the
zoom ratio using the ZOOM button on the remote during
DVD playback.
Set Zoom size.
Press ZOOM repeatedly to change display as follows.
Advanced Operation
SUB TITLE
• DVD Karaoke (1 vocal) VOCAL ON VOCAL OFF
• DVD Karaoke (2 vocals) VOCAL V1 VOCAL V2 VOCAL V1 + V2 VOCAL OFF
• You can enlarge the center portion of the image to one of 2
magnifications.
X 1.0 (ORIGINAL)
X 1.5 (ZOOM 1)
1st press
X 2.0 (ZOOM 2)
2nd press
ZOOM 2
ZOOM 1
3rd press
■ Use the , , and buttons to move the
position up, down, left and right.
47
Disc Operation (continued)
Title menu (DVD only)
Some DVDs have more than one title, e.g. movies. If
the disc offers a title menu, you can select the desired
title number. (Operation may vary according to the
disc.)
1
T I TLE MENU
Dogs
Cas t l es
Love r s
B i r ds
Press TITLE* in Play
mode to display title
screen.
<Example>
2
T I TLE MENU
Dogs
Cas t l es
Love r s
B i r ds
B i rds
of the world
1) Press
or
NUMBER key(s) to
select a title.
2) Press SET or
PLAY to start play.
• Step 2) not necessary
when using NUMBER
key(s).
DISPLAY
ACTION
DVD menu (DVD only)
DVDs may offer a special menu. This menu may
include guides to unique contents, audio/subtitle
languages, etc. Although contents and operation may
vary, the following steps show basic steps for using the
menu.
DVD MENU
1 . SUBT I TLE
2 . AUD I O
CLEAR
MENU
SELECT
SET
<Example>
a
NUMBER
key
PLAY
STOP
TITLE
Press MENU in Play
mode to display DVD
menu.
3 . ANGLE
<Example>
b
DVD MENU
1 . SUBT I TLE
2 . AUD I O
3 . ANGLE
<Example>
1) Press
or
NUMBER key(s) to
select an item.
2) Press SET or
PLAY to access.
• Step 2) not necessary
when using NUMBER
key(s).
Repeat step “b” if there is more than one menu.
48
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
*Important: If a remote control button does not work when pressed, press the TV/VCR, DVD button on the
remote and try the button again.
Program Play (Video CD/CD)
Check List
Unit is in TV-VCR mode, press TV/VCR.
Video CD or CD is inserted.
You can program specific tracks and order of
play.
1
2
Press ACTION in Stop mode to display MAIN
MENU.
M A I N MENU
DVD
LOCK LANGUAGE
53
TV
3
SET : SET
DVD MAIN MENU
4:3 Pan & Scan
SELECT
SET
END
4
1 6
2 7
3 8
4 9
5 10
Press DISPLAY to display Disc
Information screen.
(Disc Information Screen)
TRACK
PBC
1) Press
to select
“PLAY MODE.”
2) Press SET to
display screen.
1) Press
to
select “PROGRAM
PLAY.”
2) Press SET to
display screen.
PROGRAM PLAY
DISC
PROGRAM
11 16
5 8
12 17
15 6
13 18
1 13
14 19
3 2
15 20
2
START
CLEAR LAST
CLEAR ALL
SELECT
:
SET
: SET
END
: ACTION
START
: SET
VIDEO CD
1 : 35 : 12
NEXT : DISPLAY
Press DISPLAY again to display Unit
Information screen.
d
Press SET to enter Select mode.
Cursor move to “OFF.”
(Unit Information Screen)
SET
e
1) Press
to
select “START.”
2) Press SET to start
play of programs
in the sequence
selected.
Press
: SET
END : DISPLAY
to select “DISC.”
(Unit Information Screen)
PLAY
REPEAT: DISC
PROGRAM PLAY
SELECT :
SET
: SET
END : DISPLAY
•To cancel, press STOP during play, then press CLEAR.
Notes
• Up to 15 tracks can be programmed.
• “ ” or “ ” (depending on disc) indicates additional
for next or
PROGRAM PLAY screen. Press
previous screen.
• To clear the last program one by one,
to move to “CLEAR LAST” and press
Press
SET. (Pressing CLEAR also clears last program.)
• To clear all programs,
to move to “CLEAR ALL” and press SET.
Press
(Programs are also cleared when the power is turned off or the
disc is removed.)
f
Advanced Operation
PROGRAM PLAY
DISC
PROGRAM
11 16
5 8
12 17
15 6
13 18
1 13
14 19
3 2
15 20
2
: 1
: OFF
c
1) Press
to select a track
number. (Track
numbers on disc
are displayed.)
2) Press SET to set.
•Repeat step 5 to select another track.
•The selected track is added on the right side.
6
Do steps 1 through 6 on this page.
SET
:
: SET
: ACTION
CLEAR LAST
CLEAR ALL
SELECT
:
SET
: SET
END
: ACTION
1 6
2 7
3 8
4 9
5 10
a
b
:
: SET
: ACTION
PLAY MODE
SELECT
SET
END
5
CH
CLOCK
SELECT :
END
: ACT I ON
1
1) Press
to
select “DVD.”
2) Press SET to
display screen.
Program Repeat Play
(Video CD/CD)
Press SET to set mode. Cursor
move to “REPEAT.” To cancel, select
“REPEAT: OFF” in step e, then press
SET.
49
Disc Operation (continued)
Random Play (Video CD/CD)
Tracks are played in a random order.
1
2
Press ACTION* in Stop mode to display
MAIN MENU.
M A I N MENU
DVD
LOCK LANGUAGE
53
TV
If a remote control button does
not work when pressed, press
the TV/VCR, DVD button on
the remote and try the button
again.
1) Press
to select “DVD.”
2) Press SET to
display screen.
CH
CLOCK
SELECT :
END
: ACT I ON
1
*Important:
SET : SET
ACTION
CLEAR
3
DVD MAIN MENU
4:3 Pan & Scan
SELECT
SET
END
4
:
: SET
: ACTION
PLAY MODE
SELECT
SET
END
1) Press
to select
“PLAY MODE.”
2) Press SET to
display screen.
SELECT
SET
STOP
1) Press
to select
“RANDOM PLAY.”
2) Press SET to begin
random play.
:
: SET
: ACTION
• To cancel, press STOP during play, then press CLEAR.
50
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
DVD Operation using On-Screen Displays
When DISPLAY is pressed, On-Screen Displays show disc
information (title/chapter/track number, elapsed playing
time) and unit information (Repeat Play, Play mode).
1
Check List
Unit is in DVD mode, press DVD.
Press DISPLAY in Play or Stop mode to display
“On-Screen Display.”
• Each press of DISPLAY changes the on-screen display
as follows. (Please refer to page 52 or 53.)
DISPLAY
Selected disc information
Selected unit information
NUMBER
keys
Normal Screen
CLEAR
Note
SELECT
• DISPLAY button does not function while DVD TITLE MENU
is displayed.
SET
2
1) Press
(or
) to select an item.
2) Press SET to set.
3
1) Press
to select the setting.
2) Press SET to set.
<Example of DVD>
T I TLE
: 12
CHAPTER : 11
DVD
0 : 12 : 34
T I TLE
: 12
CHAPTER : 24
NEXT : DISPLAY
SELECT :
SET
: SET
NEXT : DISPLAY
<Example of Video CD>
TRACK
PBC
: 12
: OFF
TRACK
PBC
SET
: 17
: OFF
: SET
SET
: SET
VIDEO CD
0 : 12 : 34
VIDEO CD
0 : 12 : 34
NEXT : DISPLAY
Notes
• When DISPLAY is pressed during
play of a Video CD with play control,
the NUMBER keys are not available
on the displayed screen. In this case,
press DISPLAY again to remove the
displayed screen.
• When appears on the screen while
a button is being pressed, it means
that the corresponding operation is
prohibited by the unit or the disc.
Advanced Operation
SELECT :
SET
: SET
DVD
0 : 12 : 34
• When numbers are
displayed (e.g. title
number), the NUMBER
keys are also available.
• If the number entered
is not on the disc, the
entry will have no effect.
Re-enter the correct
number.
• For more details, refer
to the disc operation
information.
To return to the
normal screen,
press CLEAR or
DISPLAY repeatedly.
NEXT : DISPLAY
51
DVD Operation using On-Screen Displays (continued)
Detailed Descriptions of Each On-Screen Display
Disc information screen (for DVD)
1. TITLE No.
• Select “TITLE,” and press SET*.
• Change the No. by pressing
or NUMBER keys, and
press SET.
1
2
T I TLE
: 1
CHAPTER : 12
DVD
1 : 12 : 55
3
4
2. Chapter No.
• Select “CHAPTER,” and press SET.
• Change the No. by pressing
or NUMBER keys, and
press SET.
SELECT :
SET
: SET
3. Disc currently being played
4. Elapsed playing time
T I TLE
: 1
CHAPTER : 12
The screen may be changed by selecting the elapsed time.
• Select the elapsed playing time (“xx:xx:xx”), and press SET.
• Change the elapsed time by pressing NUMBER keys.
Hours ➞ Minutes ➞ Seconds are entered in order.
If the time entered is not on the disc, the entry will have
no effect.
Re-enter the correct time.
e.g., press 0 - 1 - 2 - 3 - 4 - 5 for 01 : 23 : 45.
SELECT :
SET
: SET
NEXT : DISPLAY
DVD
1 : --: --
NEXT : DISPLAY
If SET is pressed while
making entries, unit returns
to the condition before
entries were made.
Hour Minutes Seconds
• This function does not work with some discs.
Disc information screen (for Video CD/ CD)
A. Track No.
• Select “TRACK,” and press SET.
• Change the No. by pressing
or NUMBER keys, and
press SET.
A
B
TRACK
PBC
: 1
: OFF
VIDEO CD
1 : 35 : 12
C
D
B. Playback control ON/OFF
[Video CD with playback control only]
ON
OFF
Video CD menu play is displayed.
Video CD menu play is not displayed.
SET
: SET
NEXT : DISPLAY
C. Disc currently being played
Video CD
CD
D. Elapsed playing time
Notes
• Track No. and elapsed playing time are not displayed during
play started from menu of Video CDs with playback control.
• When appears on the screen while a button is being pressed,
it means that the corresponding operation is prohibited by the
unit or the disc.
52
NUMBER
keys
SELECT
SET
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
*Important: If a remote control button does not work when pressed, press the DVD button on the
remote and try the button again.
Unit information screen
• Select “REPEAT”, and press SET.
• Change the desired mode during play by pressing
, and press SET.
a. Repeat Play
DVD
Video CD/CD
CHAPTER REPEAT
TRACK REPEAT
TITLE REPEAT
DISC REPEAT
REPEAT OFF
REPEAT OFF
PLAY
REPEAT : CHAPTER
a
SET
: SET
END : DISPLAY
b. Play mode [Video CD/ CD only] (See page 49 or 50.)
PROGRAM PLAY
RANDOM PLAY
----
program play
random play
normal play
PLAY
REPEAT : DISC
RANDOM PLAY
b
SET
: SET
END : DISPLAY
• CHAPTER/TITLE REPEAT PLAY (DVD)
CURRENT PLAYBACK POSITION
• TRACK/DISC REPEAT PLAY (Video CD/CD)
CURRENT PLAYBACK POSITION
TITLE
chapter
track
chapter
chapter
CHAPTER REPEAT
TITLE REPEAT
NORMAL PLAY
track
Advanced Operation
For your reference
track
TRACK REPEAT
DISC REPEAT
NORMAL PLAY
• For repeat play in VCR mode, see page 33.
53
MP3/WMA/JPEG Playback Operation
This unit can play MP3/WMA/JPEG
format CD-R or CD-RW recorded for
personal use on a PC, etc.
Some discs may not play due to
recording condition.
1
2
3
ROOT
My favorite
Press POWER* on the
remote or unit.
Press OPEN/CLOSE,
and then place an
MP3/WMA/JPEG disc
into the disc tray. Press
OPEN/CLOSE to close.
• MP3/WMA/JPEG menu
is displayed.
• Playback starts
automatically (except
JPEG files).
• CD directory is displayed.
CAR1.jpg
CAR2.jpg
END_WALTZ.mp3
PICTURES
TECHNO
picture1.jpg
picture2.jpg
picture3.jpg
picture4.jpg
POPS
Example: If the CD-R/CD-RW
file hierarchy is displayed on the
PC as shown in diagram at left,
MP3/WMA/JPEG Menu Screen,
like the one below is displayed.
Note
• File names are displayed in
ascending order (1, 2, 3...9, A, B,
C...Y, Z) in the MP3/WMA/JPEG
MENU Screen ROOT.
JAZZ.wma
MP3/WMA/JPEG MENU SCREEN
Function
Status
Folder area
(Current folder
appears green.)
ROOT
My favorite
TECHNO
POPS
JAZZ
..
CAR1
CAR2
END_WALTZ
PICTURES
PLAY MODE : NORMAL
4
Press
to move cursor to
File area or PLAY MODE.
(In STOP mode)
■ File area Operation
(In STOP mode)
Press
to select items and SET
or PLAY to start.
| (next) or
Press SKIP+
(previous) to skip a
SKIP- |
file/folder page (7files) in the File area.
Select an MP3/WMA file ( / ).
MP3/WMA Playback (See next page)
Select an JPEG file ( ).
JPEG Playback (See next page)
Select a folder ( ).
Display files/folders contained in the
folder.
Select a Parent folder ( ).
Make changes to the previous
directory display.
Counter
00 : 00 : 00
PLAY
PLAY MODE
File area
(Selected
file/folder is
highlighted.
Titles are
displayed up to
11 characters.)
Explanation of Icons
:MP3 file
:Folder
:JPEG file
:WMA file
:Parent folder
PLAY MODE selection
PLAY
MODE:
JPEG Playback
- Slide-show All MP3/WMA files are
All JPEG files are selected
NORMAL selected and played back
and played back one time
one time only.
only.
SINGLE
The selected MP3/WMA file The selected JPEG file is
REPEAT is played back repeatedly.
played back repeatedly.
The MP3/WMA files
The JPEG files contained in
contained in the selected
the selected folder are played
FOLDER folder are played back
back repeatedly.
REPEAT repeatedly. However, folders However, folders below the
below the selected folder are selected folder are not played
not played back.
back.
DISC
All MP3/WMA files are played All JPEG files are played
back repeatedly.
REPEAT back repeatedly.
MP3/WMA Playback
■ Play mode Operation
(In STOP mode)
Press
to select the desired
PLAY MODE.
5
54
Press ACTION to
return to the DVD MAIN
MENU. (Press ACTION
again to return to the
MP3/WMA/JPEG MENU.)
MPEG Layer-3 audio decoding technology licensed from
Fraunhofer IIS and Thomson multimedia.
Windows Media, and the Windows logo are trademarks,
or registered trademarks of Microsoft Corporation in
the United States and/or other countries. WMA is a
compression format developed by Microsoft Corporation.
It achieves the same sound quality as MP3 with a file size
that is smaller than that of MP3.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
MP3/WMA Playback
JPEG Playback
to select an MP3/WMA file
1 (Press/ ) in STOP
mode.
You can play JPEG images.
Displayable Image Size: 32x32~7680x7680 pixels
2
• Some JPEG format may not be played back.
Do steps 1~3 on page 54.
Press SET or PLAY to start playback.
■ Forward/Reverse Search
Press FF/SLOW+ or REW/SLOW- during play.
Press PLAY to release.
• Search speed, slow at first, increases with
each additional press of the button up to 5
levels.
■ Forward/Reverse Track Skip
| or SKIP- |
during play.
Press SKIP+
Each press skips a track.
• If pressed within first 3 seconds of playback,
skips to the previous track. If over 3 seconds,
only.)
returns to top of track. (SKIP- |
• Put unit in Stop mode before performing
folder/file selection (see step 4 on previous
page.)
■ Pause
Press PAUSE during play.
Press PLAY to release.
3
4
Note
1
Do steps 1~3 on page 54.
Press
to select an JPEG file (
).
00 : 00 : 00
PLAY
ROOT
My favorite
TECHNO
POPS
JAZZ
..
CAR1
CAR2
END_WALTZ
PICTURES
PLAY MODE : NORMAL
2
Press SET or PLAY. Selected file is
displayed.
JPEG Playback Screen
<Example: CAR1>
■ Next/Previous Search
| or SKIP- |
Press SKIP+
<Example>
Press STOP to stop play.
Only the JPEG
files in a folder that
were saved while
being displayed
are displayed.
ROOT
Press OPEN/CLOSE to eject the disc.
My favorite
The MP3 MENU is closed automatically.
CAR1.jpg
CAR2.jpg
END_WALTZ.mp3
PICTURES
Note
• Copyright protected files and files containing errors
cannot be played back. The unit skips to the next file.
picture1.jpg
<Example: CAR2>
POWER
ACTION
REW/
SLOWSTOP
STILL/
PAUSE
SKIP- |
SKIP- |
SELECT
SET
PLAY
FF/SLOW+
SKIP+
ANGLE
ZOOM
|
SKIP+
|
■ Start Slide-show
Press FF/SLOW+ or REW/SLOW-.
(see next page)
■ Enlarging an image
Press ZOOM. (see next page)
■ Rotating an image
Press ANGLE. (see next page)
■ Returned on the MP3/WMA/JPEG MENU
Press STOP. (see previous page)
3
Advanced Operation
<Example: CAR1>
OPEN/
CLOSE
Press ACTION to return to the DVD MAIN
MENU.
55
MP3/WMA/JPEG Playback Operation (continued)
JPEG Playback - Slide-show -
JPEG Playback - Zoom (During JPEG Playback.)
You can enlarge specific portions of a JPEG
picture and select the zoom ratio using the ZOOM
button on the remote during JPEG Playback.
Set Zoom size.
Press ZOOM repeatedly to change display as
follows.
Press STOP to return to the MP3/WMA/JPEG
MENU.
• You can enlarge the center portion of the image to
one of 2 magnifications.
• Operation can be done during Rotation (below).
X 1.0 (ORIGINAL)
X 1.5 (ZOOM 1)
1st press
(During JPEG Playback.)
JPEG files are displayed automatically (about
every 3 seconds) as a slide-show.
1
Press FF/SLOW+ or REW/SLOW-.
Only the JPEG files in a folder that were saved
while being displayed are displayed.
<Example>
ROOT
X 2.0 (ZOOM 2)
2nd press
My favorite
CAR1.jpg
CAR2.jpg
END_WALTZ.mp3
PICTURES
3rd press
■ Use the , , and buttons to move the
position up, down, left and right.
Note
TECHNO
• Position cannot be changed on X1.0 ORIGINAL
images.
picture1.jpg
picture2.jpg
picture3.jpg
picture4.jpg
REW/SLOWFF/SLOW+
JPEG Playback - Rotation (During JPEG Playback.)
You can rotate a JPEG picture using the ANGLE
button on the remote during JPEG Playback. (The
JPEG picture will be rotated 90° clockwise.)
Set rotation.
Press ANGLE repeatedly to change display
as below. (During JPEG Playback screen)
Press STOP to return to the MP3/WMA/JPEG
MENU.
<Example>
If FF/SLOW is pressed while picture 1 is displayed.
picture 1
picture 2
picture 3
picture 4
Image changes every 3 seconds.
If REW/SLOW- is pressed while picture 3 is
displayed.
picture 3
picture 2
picture 1
1st Press
4th Press
2nd Press
3rd Press
Notes
• Operation can be done during ZOOM (above).
• The vertical/horizontal ratio of rotated JPEG
images may vary when they are displayed.
56
Image changes every 3 seconds.
■ Still picture
Press PAUSE (only SLIDE)
■ Forward/Reverse Track Skip
| or SKIP- |
. Each press
Press SKIP+
skips a file.
■ Cancel slide show
Press STOP to return to the MP3/WMA/JPEG
MENU.
2
Press ACTION to return to the DVD MAIN
MENU.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
DVD Lock Feature
*Important:
If a remote control button does not work when
pressed, press the TV/VCR , DVD button on the
remote and try the button again.
You can prevent playback of DVDs with a specific rating level which may be unsuitable for children.
• Some DVDs are encoded with a rating level. If the disc rating is higher (stricter) than the one you preset, playback
will be prohibited.
Caution
Discs not encoded with a rating level will play even if the jacket states it is for mature audiences.
For these discs, the DVD Lock Ratings will not work.
DVD Lock Ratings (DVD only)
Perform DVD Lock setting in TV mode.
Enter your secret code to display LOCK menu.
(Perform “Enter Secret Code” steps on page 38.)
1
LOCK
US MOV I ES
: OFF
CHANGE SETT I NGS
US TV PROGRAMS
: OFF
CHANGE SETT I NGS
DVD LOCK
: OFF
CHANGE SETT I NGS
NEXT PAGE
SELECT :
SET : SET
END
: ACT I ON
ACTION
SELECT
1) Press
* to select
“DVD LOCK.”
2) Press SET to set “ON”
or “OFF.”
SET
■ “ON” ➞ DVD Lock is activated.
■ “OFF” ➞ DVD Lock is deactivated.
<When DVD Lock is activated>
2
LOCK
US MOV I ES
: OFF
CHANGE SETT I NGS
: OFF
US TV PROGRAMS
CHANGE SETT I NGS
: OFF
DVD LOCK
CHANGE SETT I NGS
NEXT PAGE
SELECT :
SET : SET
END
: ACT I ON
3
1
2
3
4
UNLOCKED
5
6
7
8
YES
NO
SELECT :
SET
: SET
1) Press
to select
rating level.
2) Press SET to
select “LOCKED” or
“UNLOCKED.”
SET : SET
LEVEL 1:
LOCK ALL:
Playback of all DVDs, CDs and Video
CDs is prohibited. (Use to prohibit play of
mature theme DVDs not encoded with a
rating level.)
LEVEL 2:
DVDs expressly for children can be played
back.
LEVEL 3 to 7: DVDs for general audiences/children
can be played back. (DVDs with mature
content are prohibited.)
LEVEL 8:
NO LIMIT: (Factory preset)
All DVDs can be played back.
• Ratings which are highlighted in Green will be blocked; those
not highlighted (white letters) will not be blocked.
4
YOUR SELECTION
EXCEEDS THE
,
PLAYER S RATING LIMIT.
DO YOU WANT TO CHANGE THE
LIMIT?
Press ACTION three times to exit.
END : DISPLAY
After DVD Lock is set and a blocked DVD
is played, this message will appear. The
message may differ depending on the
disc.
To continue viewing a blocked
program for now,
to select “YES” and SET.
Press
Then, enter your 4-digit secret code.
When “NO” is selected, blocked programs
cannot be viewed.
<When blocked programs>
Advanced Operation
LOCK ALL
SELECT :
END
: ACT I ON
1) Press
to select
“CHANGE SETTINGS.”
2) Press SET to display
screen.
PROGRAM RATING EXCEEDED
To change DVD LOCK settings
After entering your secret code in
step 3 on page 38, select “OFF” to
deactivate DVD Lock or change the
rating level.
57
Settings for DVD Operation
1
2
Press ACTION* in Stop mode to display
MAIN MENU.
M A I N MENU
DVD
LOCK LANGUAGE
53
TV
3
CH
CLOCK
SELECT :
END
: ACT I ON
1
DVD MAIN MENU
Check List
Unit is in TV-VCR mode, press TV/VCR.
SET : SET
DISC LANGUAGES
AUDIO OUTPUT
ST I L L MODE
: AUTO
TV MODE
: 4 : 3 Pan & Scan
SELECT
SET
END
1) Press
to
select “DVD.”
2) Press SET to
display screen.
Once initial settings are done, they remain
in memory (even after the power is off) until
changed. This means the unit will always
operate under the same conditions (especially
DVDs) each time.
1) Press
to
select an item.
2) Press SET to set.
:
: SET
: ACTION
DISC LANGUAGES (See below.)
Any languages offered on the disc can be set. If a
language not offered is set, the original disc language
will be selected.
AUDIO OUTPUT (See page 59.)
You can set the audio output that comes from the
digital audio output terminal.
STILL MODE (See page 60.)
To select “FIELD” or “FRAME” to prevent jitter or to
make small text or fine patterns clearly visible in a still
picture. When “AUTO” is set, “FIELD” or “FRAME” is
selected automatically.
TV MODE (See page 60.)
To select whether the video material for a wide-screen
will be played back in Pan & Scan style or in Letterbox
style.
DISC LANGUAGES (DVD only)
To select and set the language of the audio soundtrack,
subtitles, or title/DVD menus for all discs to be played.
4
DVD MAIN MENU
DISC LANGUAGES
AUDIO OUTPUT
ST I L L MODE
: AUTO
TV MODE
: 4 : 3 Pan & Scan
SELECT
SET
END
5
:
: SET
: ACTION
DISC LANGUAGES
AUDIO
SUBT I TLE
MENUS
SELECT
SET
END
1) Press
to
select “DISC
LANGUAGES.”
2)Press SET to
display screen.
: English
: AUTO
: English
:
: SET
: ACTION
1) Press
to
select an item.
2) Press SET
repeatedly for
desired language.
(Please refer right.)
Press ACTION to redisplay DVD MAIN MENU
and go to step 3 to setup another item.
6 press ACTION three times to exit.Or,
58
“AUDIO” selections
To select the audio soundtrack language.
(Factory preset: English)
English/Spanish/French/Japanese
Original: Original disc language
OTHER ✱✱✱✱: Other language selection*1
“SUBTITLE” selections
To select the subtitle language.
(Factory preset: AUTO)
AUTO: Same language selected for “AUDIO”
• If language set for “AUDIO” is
used in playback, subtitles will not
appear.
• If another language is used during
playback, the subtitles will appear
in the language selected at “AUDIO”
setup.
English/Spanish/French/Japanese
OTHER ✱✱✱✱: Other language selection*1
“MENUS” selections
(Factory preset: English)
To select the language used in title menus or
DVD menus.
English/Spanish/French/Japanese
OTHER ✱✱✱✱: Other language selection*1
To enter OTHER ✱✱✱✱ code number,
Press NUMBER keys (Please refer to
language codes on page 61).
repeatedly to
To make corrections, press
delete language code number, and correct.
*1 If the selected language is not offered, the
original disc language is selected.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
*Important: If a remote control button does not work when pressed, press the TV/VCR , DVD
button on the remote and try the button again.
AUDIO OUTPUT
Select the digital output to be output from the optical
digital audio output connector of the unit.
ACTION
1
2
SELECT
Do steps 1 and 2 on page 58.
SET
DVD MAIN MENU
DISC LANGUAGES
AUDIO OUTPUT
ST I L L MODE
: AUTO
TV MODE
: 4:3 Pan & Scan
SELECT
SET
END
:
: SET
: ACTION
AUDIO OUTPUT
3
LPCM(DVD)
Dolby Digital
dts
DRC
SELECT
SET
END
: OFF
: Bitstream
: Bitstream
: OFF
:
: SET
: ACTION
1) Press
to
select “AUDIO
OUTPUT.”
2) Press SET to
display screen.
1) Press
to
select an item.
2) Press SET
repeatedly for
output. (See
below.)
■ “LPCM (DVD)” selections
OFF:
PCM:
Linear PCM of less than 48 kHz/16 bit
is output. When playing DVDs recorded
in linear PCM of over 48 kHz/20 bit, no
digital audio is output. (Factory preset)
When playing DVDs recorded in
linear PCM of 48 kHz/20 bit/24 bit or
more, digital audio converted to 44.1
kHz/16 bit or 48 kHz/16 bit is output.
(Digital output of PCM audio is restricted
to48 kHz/16 bit or below for copyright
protection.)
■ “Dolby Digital” selections
■ “dts” selections
Recommended setting
LPCM
(DVD)
Dolby
Digital
dts
AV amplifier
without Dolby
Digital/dts
decoder
PCM
PCM*1
PCM*1
AV amplifier
including
Dolby Digital
decoder
PCM
Bitstream
PCM
AV amplifier
including
Dolby
Digital/dts
decoder
PCM
Bitstream Bitstream*2
No amplifier
is connected
Bitstream: dts bitstream is output. (Factory preset)
PCM:
When you have connected a amplifier
that doesn’t have a built-in dts decoder.
• Make settings according to amplifier
connected to optical audio output as shown
in above table.
■ “DRC (Dynamic Range Compression)”
selections
*1 When connecting an amplifier (with an
optical digital input connector) which
does not contain the Dolby Digital or
dts decoder, be sure to select “PCM.”
If “Bitstream” is selected, starting DVD
play may cause such a high level of noise
as to be harmful to your ears and damage
the speakers.
*2 When a dts decoder is connected, please
select “Bitstream” in “dts.” If “PCM” is
selected, there will be stereo sound.
OFF:
ON:
4
Normal audio range is selected. (Factory
preset)
For dynamic sound even at low volume,
this is useful for late-night listening.
[Dolby Digital DVDs only].
Press ACTION to redisplay DVD MAIN MENU
and go to step 2 to setup another item. Or,
press ACTION three times to exit.
Advanced Operation
Bitstream: Dolby Digital bitstream (1ch-5.1ch) is
output. (Factory preset)
PCM:
When you have connected a amplifier
that doesn’t have a built-in Dolby Digital
decoder.
Type of
amplifier
to be
connected
59
Settings for DVD Operation (continued)
STILL MODE
Set to reduce jitter in a displayed still picture or a motion
picture.
1
2
Do steps 1 and 2 on page 58.
DVD MAIN MENU
DISC LANGUAGES
AUDIO OUTPUT
ST I L L MODE
: AUTO
TV MODE
: 4 : 3 Pan & Scan
*Important:
If a remote control button does not
work when pressed, press the DVD
button on the remote and try the
button again.
1) Press
* to select
“STILL MODE.”
2) Press SET repeatedly
for mode. (See below)
ACTION
SELECT
SET
END
:
: SET
: ACTION
SELECT
AUTO:
“FIELD” (Field still) or “FRAME” (Frame still)
is automatically selected during the still mode.
(Factory preset)
FIELD: “FIELD” (Field still) is always selected.
This setting will reduce jitter when compared
with “AUTO” on some discs.
FRAME: “FRAME” (Frame still) is always selected.
Some texts and fine patterns will be seen clearly
when compared with “AUTO” on some discs.
3
SET
Press ACTION twice to exit this mode.
Selecting TV MODE
Set the screen display style for widescreen video material
playback.
a
b
Do steps 1 and 2 on page 58.
Example
DVD MAIN MENU
DISC LANGUAGES
AUDIO OUTPUT
ST I L L MODE
: AUTO
TV MODE
: 4 : 3 Pan & Scan
SELECT
SET
END
1) Press
to select “TV
MODE.”
2) Press SET repeatedly
for mode. (See below.)
:
: SET
: ACTION
4:3 Pan & Scan : Widescreen video data is played in Pan
(Factory preset)
& Scan style (left and right of screen is
trimmed.)
• Video data not formatted in Pan &
Scan will play in letterbox style.
4:3 Letterbox : Widescreen video data is played in
Letterbox style (top and bottom of
screen has black margin).
c
60
4:3 Pan & Scan (Factory preset)
4:3 Letterbox
Press ACTION twice to exit this mode.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Language Code List
Enter the appropriate code number for the initial settings “AUDIO,” “SUBTITLE” and/or “MENUS” (see
page 58).
Code Language
Code Language
Code Language
Code Language
7079 Faroese
7678 Lingala
8375 Slovak
6566 Abkhazian
7082 French
7679 Laothian
8376 Slovenian
6570 Afrikaans
7089 Frisian
7684 Lithuanian
8377 Samoan
6577 Ameharic
7165 Irish
7686 Latvian, Lettish
8378 Shona
6582 Arabic
7168 Scots Gaelic
7771 Malagasy
8379 Somali
6583 Assamese
7176 Galician
7773 Maori
8381 Albanian
6588 Aymara
7178 Guarani
7775 Macedonian
8382 Serbian
6590 Azerbaijani
7185 Gujarati
7776 Malayalam
8385 Sundanese
6665 Bashkir
7265 Hausa
7778 Mongolian
8386 Swedish
6669 Byelorussian
7273 Hindi
7779 Moldavian
8387 Swahili
6671 Bulgarian
7282 Croatian
7782 Marathi
8465 Tamil
6672 Bihari
7285 Hungarian
7783 Malay
8469 Telugu
6678 Bengali;Bangla
7289 Armenian
7784 Maltese
8471 Tajik
6679 Tibetan
7365 Interlingua
7789 Burmese
8472 Thai
6682 Breton
7378 Indonesian
7865 Nauru
8473 Tigrinya
6765 Catalan
7383 Icelandic
7869 Nepali
8475 Turkmen
6779 Corsican
7384 Italian
7876 Dutch
8476 Tagalog
6783 Czech
7387 Hebrew
7879 Norwegian
8479 Tonga
6789 Welsh
7465 Japanese
7982 Oriya
8482 Turkish
6865 Danish
7473 Yiddish
8065 Panjabi
8484 Tatar
6869 German
7487 Javanese
8076 Polish
8487 Twi
6890 Bhutani
7565 Georgian
8083 Pashto, Pushto
8575 Ukrainian
6976 Greek
7575 Kazakh
8084 Portuguese
8582 Urdu
6978 English
7576 Greenlandic
8185 Quechua
8590 Uzbek
6979 Esperanto
7577 Cambodian
8277 Rhaeto-Romance
8673 Vietnamese
6983 Spanish
7578 Kannada
8279 Romanian
8679 Volapük
6984 Estonian
7579 Korean
8285 Russian
8779 Wolof
6985 Basque
7583 Kashmiri
8365 Sanskrit
8872 Xhosa
7065 Persian
7585 Kurdish
8368 Sindhi
8979 Yoruba
7073 Finnish
7589 Kirghiz
8372 Serbo-Croatian
9072 Chinese
7074 Fiji
7665 Latin
8373 Singhalese
9085 Zulu
For Your Information
6565 Afar
61
Before Requesting Service
Check the following points once again if you are having trouble with your unit.
Power
Correction
No power…
• Completely insert Power Plug into an AC outlet.
• Set POWER button to ON.
• Auto power-off (shut off) occurs after about 5 min. in DVD mode with no
operation, or if there is no broadcast signal in TV or Playback mode. Turn the
power back on.(P. 21, 35)
Power turns itself off...
Monitor
Correction
• Make sure your antenna system (TV or CABLE), is correctly set. (P. 11)
No picture or sound...
• Completely insert Power Plug into an AC outlet.
• Set POWER button to ON.
Poor picture with normal • Adjust BRIGHTNESS, SHARPNESS, and PICTURE controls in the SET UP
sound...
Video Adjustment. (P. 45)
Poor sound with normal • Adjust VOLUME control. (P. 22)
picture...
• Adjust SHARPNESS and PICTURE controls in the SET UP Video
Poor TV reception...
Adjustment. (P. 45)
No color or poor color... • Adjust TINT and COLOR controls in the SET UP Video Adjustment. (P. 45)
Ghost (multiple)
• Install a directional antenna.
images...
TV programs cannot be
• Make sure the selected channel is in unit’s memory. (P. 16)
watched...
Channel cannot be
• Only the channel being recorded can be viewed on this unit.
selected...
VCR
Correction
TV program cannot be
recorded...
• Make sure your antenna system (TV or CABLE), is correctly set. (P. 11)
• Make sure cassette record tab is intact. (P. 4)
• Check that clock is set to current time and date.
• Make sure DSS/CABLE box (if used) is left on and tuned to channel to be
recorded.
Timer recording cannot
• Set recording Start/Stop times correctly. (P. 30-31)
be performed…
• Timer recording may not be performed or continued if a power interruption
of more than 1 minute occurs before or during a Timer Recording, even after
power is restored.
No playback picture,
or the playback picture • Adjust TRACKING control in either direction. (P. 6)
• Try Head Cleaning. (P. 6)
is noisy or contains
streaks...
VCR cannot be
• Make sure VCR LOCK is set to off. (P. 37)
controlled...
Remote Control Correction
• Aim Remote directly at the remote sensor on the unit. (P. 9)
Unit cannot be
controlled...
ACTION, PLAY,
SELECT, SET POWER,
etc. buttons cannot be
selected...
62
•
•
•
•
Avoid any object blocking signal path.
Inspect the remote batteries. (P. 4)
Make sure VCR LOCK is set to off. (P. 37)
Exposing unit remote sensor to direct fluorescent or outdoor light may cause
signal interference.
• Press TV/VCR for TV-VCR mode. (P. 22)
• Press DVD for DVD mode. (P. 20)
• Press FM for FM mode. (P. 28)
• Check remote batteries.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
DVD/Video CD/CD Correction
Play fails to start even
when PLAY is pressed...
Play starts but then
stops
immediately...
Picture is distorted
during rapid advance or
rapid reverse...
No Forward/Reverse
search play...
Play does not start even
when title is selected...
Audio soundtrack and/or
subtitle language is not
the one selected at the
initial settings...
• This unit cannot play discs other than DVDs, Video CDs and CDs.
• The disc may be dirty and require cleaning.
No subtitles...
• Subtitles appear only when available on disc.
• Select “ON” at the “Subtitle language” section (P. 46) to display subtitles.
Alternative audio
soundtrack
(or subtitle) language
cannot be selected...
• Alternative language cannot be selected with discs which do not contain more than
one language.
• For some discs, alternative language cannot be selected with the AUDIO or SUB
TITLE button. Try selecting it from the DVD MAIN MENU if available.
Angle cannot be
changed...
• This function is dependent on software availability. Even if disc has multiple angles,
they may be recorded for specific scenes only (ANGLE Indicator on unit lights up). (P.
47)
Miscellaneous
Correction
Video cassette cannot
be inserted...
Video cassette cannot
be removed...
Eject does not function
or insertion cannot be
done...
Video cassette ejects
when a recording is
started, or the power is
turned off for timer
recording...
The disc cannot be
removed...
• Be sure disc is installed with label side up.
• The picture will be somewhat distorted at times: this is normal.
• Some discs may have sections which prohibit Forward/Reverse search. (P. 21)
• Confirm the “DVD LOCK” setting. (P. 57)
• If the audio soundtrack and/or subtitle language selected at DVD initial settings
does not exist on the disc, it will not be accessible.
• Insert the cassette window side up; record tab facing you.
• Completely insert Power Plug into an AC outlet.
• Turn the POWER off and then on, and try ejecting or inserting the tape again.
• Make sure cassette record tab is intact. (P. 4)
• First, unplug unit. Then, prepare a rigid wire (e.g. an extended paper clip, etc.) and,
applying moderate force, insert it straight into the hole at the base of the tray. The
tray will eject a little. Now, pull the tray all the way out and remove the disc. (P. 10)
In Stop mode, the VCR • To enable Quick Play mechanism, the VCR cylinder will rotate for about 3 minutes.
This reduces response time from Stop to Play mode and from Play to Rewind Search
motor (CYLINDER)
mode.
continues to rotate..
For Your Information
If you cannot resolve the problem, please call the Customer Satisfaction Center for product
assistance at 1-800-211-PANA(7262).
To locate an authorized servicenter call toll free 1-800-211-PANA(7262)
or send e-mail to : [email protected]
63
Warning and Instruction Displays
These displays will alert you of a missed operation or provide further instructions.
OSD
PLEASE SET
CLOCK BEFORE
PROGRAMMING
CHECK CASSETTE
RECORD TAB
TO CANCEL TIMER
REC HOLD DOWN
STOP KEY FOR
APPROX 3 SEC
NO CASSETTE
PLEASE INSERT A
CASSETTE
PLEASE PREPARE
FOR TIMER REC
VIDEO HEADS MAY
NEED CLEANING
PLEASE INSERT
HEAD CLEANING
CASSETTE OR
REFER TO MANUAL
END: PLAY
VCR LOCK
ACTIVATED
PLEASE CHECK
THE DISC, AND
FOR STAINS OR
SCRATCHES ON
DISC
THIS DISC MAY NOT
BE PLAYED IN YOUR
REGION
THIS TYPE OF DISC
CANNOT BE PLAYED.
PLEASE INSERT A
DIFFERENT DISC
CANNOT PLAY THIS
FILE
THIS FILE IS
PROTECTED
IT IS PROHIBITED
TO COPY DVD/
VIDEO CD/CD TO
VHS
64
Caution
If you attempt to set or review a Timer Recording or set the On-Timer and the Clock
is not set... (P.16-17)
If you press REC, and a cassette is inserted with no record tab... (P.4, 18)
If you press STOP during a Timer Recording... (P.31)
If you press PLAY, FF, REW, or REC without a cassette inserted... (P.18)
If the unit is not in Stop mode or a cassette with record tab is not inserted two
minutes before a Timer Recording is about to begin... (P.30-31)
If head cleaning becomes necessary while playing back a tape... (P.6)
If you press a function button other than STOP/EJECT or POWER while the unit is
in VCR Lock mode... (P.37)
If you press PLAY, or the unit reads data from a stained or scratched disc in DVD
mode. Also, if the type of disc is other than DVD, Video CD or CD... (P.7)
Playback of a disc with different region number was attempted. Only discs marked
region “1,” “ALL,” or those that include “1” are playable on this unit. (P.3)
An unusable disc is inserted in the unit. (P.7)
This file format cannot be played.
(Appears during MP3/WMA/JPEG file playback)(P.54)
This file is copyright protected and cannot be played back.
(Playback is prohibited.)(P.54)
If you press REC in DVD mode... (P.18-19)
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Spanish Quick Use Guide/Guía para rápida consulta
■ Conexión para Ant./Cable
Conecte Ant./Cable a la entrada de antena de la TV
(VHF/UHF).
VHF/UHF
VHF/UHF
Ant./Cable
■ Conexión para Sistema Digital de
Satelite (DSS)/Convertidor de cable
Conecte la salida del convertidor de cable la entrada
“VFH/UHF” con el RF cable.
Convertidoe de cable
Nota
• Los botones de funciones son inoperantes
durante la Configuración inicial.
• Para retirar un cassette durante el Ajuste
automático, pulse EJECT dos veces en el control
remoto o STOP dos veces en el VCR. En este
caso, los ajustes se deben realizar manualmente.
(Vea la p.16-17 de Libro de operaciones
avanzadas).
• Dependiendo de las condiciones, puede
que el Ajuste automático del reloj tarde
más de 30 minutos. En ese caso, pulse STOP
para detener la configuración y realice los ajustes
manualmente. (Vea la p.16-17 de Libro de
operaciones avanzadas).
Ajuste Manual del Reloj
Si el ajuste automático del reloj no se ha
completado, ajuste el reloj manualmente de la
siguiente manera.
VHF/UHF
VHF/UHF
Ant./Cable
Conecte por favor todas las conexiones del cable o
de la antena antes de energizar los aparatos.
1
2
Presione ACTION en el control
remoto para visualizar la pantalla
del menú RELOJ.
Presione ▲▼ para seleccionar el
mes y SET para colocarlo. De la
misma forma, seleccione y ajuste
la fecha, año, hora y DST (Hora de
Verano).
3
Presione dos veces la tecla
ACTION para poner el RELOJ en
marcha y salir.
Realizando Configuración Inicial
Presione TV/VCR para la modalidad TV-VCR.
1
2
Conecte el cable electrico de la unidad
en el enchufe de pared de la CA.
CH AUTO SET PROCEEDING
AUTO CLOCK SET
PROCEEDING
Encienda la TV
mediante el control
o directamente en
la unidad. La unidad
inicia la busqueda
de canales y
ajusta el tiempo
automaticamente.
Ajustar de nuevo el reloj
1
2
• Si usa convertidor de cable, enciendala y seleccione el
Servicio Publico de Canales de Television (PBS) en su
horario de uso o tiempo de su zona. Si utiliza receptor
DSS este debe de estar apagado.
SETT I NG : CH 1 0
AUTO CLOCK SET
COMPLETED
AUTO CLOCK SET
I S I NCOMPLETE
PLEASE SET CLOCK BY
PRESS I NG ACT I ON KEY
DVD
BLOQUEO IDIOMA
53
Selecciones
se realizaran
automaticamente,
cuando la
configuracion
termine la pantalla
siguiente aparecera.
• Si “AUTO CLOCK SET IS
INCOMPLETE” aparece
en pantalla, coloque
el tiempo usando el
procedimiento manual
(MANUAL CLOCK SET),
vealo enseguida.
Continúa...
RELOJ
1
CANAL
ELEGIR :
FIJAR : SET
TERMINAR : ACT I ON
3
FIJAR RELOJ
FIJACION AUTOMATICA
MANUAL
AJUSTE ZONA HORA : 0
ELEGIR :
FIJAR : SET
TERMINAR : ACTION
4
FIJAR RELOJ
2 / 6/2003 JUE 12: 00PM
VERANO : ACT
ELEGIR HORA
ELEGIR:
FIJAR : SET RETROCEDER:
I NIC I AR : ACTION
5
Presione
▲▼◄► para
seleccionar
“RELOJ,” y
luego Presione
SET.
Presione ▲▼
para seleccionar
“MANUAL” y
luego presione
SET.
Presione ▲▼ y
SET para
seleccionar y
ajustar la hora y
la fecha.
Presione ACTION dos veces para
que el reloj comience a funcionar y
salir de est
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement