Panasonic | CQC1301U | Operating instructions | Panasonic CQC1301U User manual

MUTE
1
2
SCROLL
RANDOM
SCAN
3
4
5
REPEAT
SQ
6
DI S C
D·M
Operating Instructions
CLOCK
DISP
Warning
Caution
This pictograph intends to alert you to the presence of
important operating instructions and installation instructions. Failure to heed the instructions may result in
injury or material damage.
Observe the following cautions when using this
unit.
❑ Keep the sound volume at an appropriate level.
Keep the volume level low enough to be aware of road and traffic
conditions while driving.
❑ This unit is designed for use exclusively in automobiles.
❑ Do not operate the unit for a prolonged period with the
engine turned off.
Operating the audio system for a long period of time with the
engine turned off will drain the battery.
(CQ-C1401U)
Observe the following warnings when installing.
Warning
Observe the following warnings when using this
unit.
❑ The driver should neither watch the display nor operate
the system while driving.
Watching the display or operating the system will distract the driver from looking ahead of the vehicle and can cause accidents.
Always stop the vehicle in a safe location and use the parking
brake before watching the display or operating the system.
❑ Use the proper power supply.
This product is designed for operation with a negative grounded
12 V DC battery system. Never operate this product with other battery systems, especially a 24 V DC battery system.
❑ Keep batteries and insulation film out of reach of infants.
Batteries and insulation film can be ingested, so keep them out of
the reach of infants. If an infant ingests a battery or insulation film,
please seek immediate medical attention.
❑ Protect the Deck Mechanism.
Do not insert any foreign objects into the slot of this unit.
❑ Do not disassemble or modify the unit.
Do not disassemble, modify the unit or attempt to repair the product yourself. If the product needs to be repaired, consult your
dealer or an authorized Panasonic Servicenter.
❑ Do not use the unit when it is out of order.
If the unit is out of order (no power, no sound) or in an abnormal
state (has foreign objects in it, is exposed to water, is smoking, or
smells), turn it off immediately and consult your dealer.
❑ The remote control unit should not lie about in the car.
If the remote control unit lies about, it could fall on the floor while
driving, get wedged under the brake pedal, and lead to a traffic
accident.
❑ Refer fuse replacement to qualified service personnel.
When the fuse blows out, eliminate the cause and have it replaced
with the fuse prescribed for this unit by a qualified service engineer. Incorrect replacement of the fuse may lead to smoke, fire,
and damage to the product.
TEXT
Caution
(Only for
CQ-C1401U)
❑ Disconnect the lead from the negative (–) battery terminal before installation.
Wiring and installation with the negative (–) battery terminal connected may cause electrical shock and injury due to a short circuit.
Some cars equipped with the electrical safety system have specific
procedures of battery terminal disconnection.
FAILURE TO FOLLOW THE PROCEDURE MAY LEAD TO THE
UNINTENDED ACTIVATION OF THE ELECTRICAL SAFETY SYSTEM
RESULTING IN DAMAGE TO THE VEHICLE AND PERSONAL
INJURY OR DEATH.
❑ Never use safety-related components for installation,
grounding, and other such functions.
Do not use safety-related vehicle components (fuel tank, brake,
suspension, steering wheel, pedals, airbag, etc.) for wiring or fixing the product or its accessories.
❑ Installing the product on the air bag cover or in a location
where it interferes with airbag operation is prohibited.
❑ Check for piping, gasoline tank, electric wiring, and other
items before installing the product.
If you need to open a hole in the vehicle chassis to attach or wire
the product, first check where the wire harness, gasoline tank, and
electric wiring are located. Then open the hole from outside if possible.
❑ Never install the product in a location where it interferes
with your field of vision.
❑ Never have the power cord branched to supply other
equipment with power.
❑ After installation and wiring, you should check the normal operation of other electrical equipment.
The continuation of their using in abnormal conditions may cause
fire, electrical shock or a traffic accident.
❑ In the case of installation to an airbag-equipping car,
confirm warnings and cautions of the vehicle manufacturer before installation.
❑ Make sure the leads do not interfere with driving or getting in and out of the vehicle.
❑ Insulate all exposed wires to prevent short circuiting.
❑ Do not expose the unit to direct sunlight or excessive
heat.
Otherwise these will raise the interior temperature of the unit,
and it may lead to smoke, fire, or other damage to the unit.
❑ Do not use the product where it is exposed to water,
moisture, or dust.
Exposure of the unit to water, moisture, or dust may lead to
smoke, fire, or other damage to the unit. Make especially sure
that the unit does not get wet in car washes or on rainy days.
Observe the following cautions when installing.
❑ Refer wiring and installation to qualified service personnel.
Installation of this unit requires special skills and experience. For
maximum safety, have it installed by your dealer. Panasonic is
not liable for any problems resulting from your own installation
of the unit.
❑ Follow the instructions to install and wire the product.
Not following the instructions to properly install and wire the
product could cause an accident or fire.
❑ Take care not to damage the leads.
When wiring, take care not to damage the leads. Prevent them
from getting caught in the vehicle chassis, screws, and moving
parts such as seat rails. Do not scratch, pull, bend or twist the
leads. Do not run them near heat sources or place heavy objects
on them. If leads must be run over sharp metal edges, protect
the leads by winding them with vinyl tape or similar protection.
Speaker impedance
Pre-amp output voltage
Pre-amp output impedance
Subwoofer output voltage
Subwoofer output impedance
Dimensions (W x H x D)
Weight
Disc Player
Sampling frequency
DA converter
Pick-up type
Light source
Wave length
Frequency response
Signal to noise ratio
Total harmonic distortion
Wow and flutter
Channel separation
: 8 times oversampling
: 1 bit DAC System
: Astigma 3-beam
: Semiconductor laser
: 790 nm
: 20 Hz – 20 kHz (±1 dB)
: 96 dB
: 0.01 % (1 kHz)
: Below measurable limits
: 75 dB
AM Radio
Frequency range
Usable sensitivity
1
Power Output:
17 W RMS x 4 Channels at 4 Ω and ≤ 1%
THD+N
Signal to Noise Ratio:
85 dBA (reference: 1 W into 4 Ω)
Set your car's ignition switch to the ACC or
ON position.
The demonstration screen appears.
Q'ty: 1 set
Installation Instructions
(YEFM293891)
Q'ty: 1
Owners Information
Card
Pull the insulation film out from the
backside of the remote control
gently.nly
1
Note: Battery Information:
Battery Type: Panasonic lithium battery (CR2025) (Included in
the remote control)
Battery Life: Approximately 6 months under normal use (at
room temperature)
Press [DISP] (CLOCK).
Clock Display at Power Off
3
(YEFC05657)
Q'ty: 1
Rubber Bushing
Q'ty: 1
Hours set
Power Connector
(YEAJ02877)
Q'ty: 1
POWER
SOURCE MENU
SEL
SRC
VOL
SET
BAND
MUTE
1
2
3
RANDOM
SCAN
REPEAT
4
5
6
7
8
9
0
DISP
TUNE
#
Q'ty: 1
Remote Control Unit
(includes a battery)
NUMBER
CAR AUDIO
Q'ty: 1
(EUR7641010)
Q'ty: 1
Notes:
¡ The number in parentheses underneath each accessory part name is the part number for maintenance and service.
¡ Accessories and their part numbers are subject to modification without prior notice due to improvements.
¡ Mounting Collar and Trim Plate are mounted on the main unit at shipment.
Panasonic Sales Company,
Division of Matsushita Electric of
Puerto Rico, Inc. (“PSC”)
Ave. 65 de Infanteria, Km. 9.5
San Gabriel Industrial Park,
Carolina, Puerto Rico 00985
http://www.panasonic.com
Panasonic Canada Inc.
5770 Ambler Drive,
Mississauga, Ontario
L4W 2T3
http://www.panasonic.ca
YEFM285597A NT1104-1114
Printed in China
[[]: sets the hour ahead.
[]]: sets the hour back.
4 Press [DISP] (CLOCK).
Minutes blinks
5 Adjust the minute.
Minutes set
[[]: sets the minute ahead.
[]]: sets the minute back.
6 Press [DISP] (CLOCK).
Complete
Notes:
¡ “ADJUST” is displayed before adjusting the clock.
¡ Hold down []] or [[] to change numbers rapidly.
Yes
No
XM Satellite Radio
supported (XM receiver [XMD1000] is needed)
not supported
Subwoofer output
Yes
No
Features
CD changer control
Obtain Product Information and Operating Assistance;
locate your nearest Dealer or Servicenter; purchase Parts
and Accessories; or make Customer Service and Literature
requests by visiting our Web Site at:
http://www.panasonic.com/support
or, contact us via the web at:
http://www.panasonic.com/contactinfo
You may also contact us directly at:
1-800-211-PANA (7262),
Monday-Friday 9 am-9 pm; Saturday-Sunday 10 am-7 pm,
EST.
For hearing or speech impaired TTY users, TTY : 1-877-8338855
Accessory Purchases:
Purchase Parts, Accessories and Instruction Books online
for all Panasonic Products by visiting our Web Site at:
http://www.pasc.panasonic.com
or, send your request by E-mail to:
npcparts@panasonic.com
You may also contact us directly at:
1-800-332-5368 (Phone) 1-800-237-9080 (Fax Only)
(Monday-Friday 9 am to 8 pm, EST.)
Panasonic Services Company
20421 84th Avenue South, Kent, WA 98032
(We accept Visa, MasterCard, Discover Card, American
Express, and Personal Checks)
For hearing or speech impaired TTY users, TTY : 1-866-6051277
Caution
Display off
¡ This face plate is not waterproof. Do not expose it to
water or excessive moisture.
¡ Do not remove the face plate while driving your car.
¡ Do not place the face plate on the dashboard or nearby
areas where the temperature rises high.
¡ Do not touch the contacts on the face plate and the main
unit, since this may result in poor electrical contact.
¡ If dirt or other foreign substances get on the contacts,
wipe them off with a clean and dry cloth.
Removing
Mounting
1 Turn off the power.
2 Press [ ]. The face plate will open.
3 Pull it out toward you.
1 Slide the left side of the face plate in place.
2 Press the right end of face plate until a
“click” is heard.
2
1
1
2
LIMITED WARRANTY COVERAGE
If your product does not work properly because of defects in materials
and workmanship.
Panasonic Consumer Electronics Company or Panasonic Sales Company
(collectively referred to as “the warrantor”) will, for the length of the period indicated in the chart below, which starts with the date of original purchase (“warranty period”), at its option either (a) repair your product with
new or refurbished parts, or (b) replace it with a new or refurbished
product. The decision to repair or replace will be made by the warrantor.
Categories
CANADA
WARRANTY SERVICE
For product operation and information assistance, please
contact your Dealer or our Customer Care Centre at:
Telephone #: (905) 624-5505 Fax #: (905) 238-2360
Web: www.panasonic.ca
For product repairs, please contact one of the following:
・Your Dealer who will inform you of an authorized
Servicentre nearest you.
・Our Customer Care Centre at (905) 624-5505 or
www.panasonic.ca
・A Panasonic Factory Servicentre listed below:
Richmond, British
Columbia
Panasonic Canada Inc.
12111 Riverside Way
Richmond, BC V6W 1K8
Tel: (604) 278-4211
Fax: (604) 278-5627
Calgary, Alberta
Panasonic Canada Inc.
6835-8th St. N. E. Calgary,
AB T2E 7H7
Tel: (403) 295-3955
Fax: (403) 274-5493
Mississauga, Ontario
Panasonic Canada Inc.
5770 Ambler Dr.
Mississauga, ON L4W 2T3
Tel: (905) 624-8447
Fax: (905) 238-2418
Lachine, Quebec
Panasonic Canada Inc.
3075, rue Louis A. Amos
Lachine, QC H8T 1C4
Tel: (514) 633-8684
Fax: (514) 633-8020
MXE Series Audio Components (except items
listed below)
Speakers
Two (2) Years
Two (2) Years
One (1) Year
Not Applicable
Accessories (in exchange for defective items)
Ninety (90) Days Not Applicable
During the “Labor” warranty period, there will be no charge for labor.
During the “Parts” warranty period, there will be no charge for parts. You
must carry-in or mail-in your product during the warranty period. If nonrechargeable batteries are included, they are not warranted. This warranty
only applies to products purchased and serviced in the United States or
Puerto Rico. This warranty is extended only to the original purchaser of a
new product which was not sold “as is”. A purchase receipt or other
proof of the original purchase date is required for warranty service.
CARRY-IN OR MAIL-IN SERVICE
For Carry-In or Mail-In Service in the United States, call 1-800-211-PANA
(7262) or visit
Panasonic Web Site: http://www.panasonic.com
For assistance in Puerto Rico, call Panasonic Sales Company (787)-7504300 or fax (787)-768-2910.
LIMITED WARRANTY LIMITS AND EXCLUSIONS
This warranty ONLY COVERS failures due to defects in materials and
workmanship, and DOES NOT COVER normal wear and tear or cosmetic
damage. The warranty ALSO DOES NOT COVER damages which occurred
during shipment, failures which are caused by products not supplied by
the warrantor, failures which result from accident, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty installation, set-up
adjustment, maladjustment of consumer control, improper maintenance,
improper antenna, inadequate signal reception or pickup, power line
surge, improper voltage supply, lightning, modification, commercial use
(such as use in hotels, offices, restaurants, or other business uses) or
rental use of the product, or service by anyone other than the technician
from Factory Servicenter or other authorized service centers, or damage
that is attributable to acts of God.
CANADA
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga Ontario L4W 2T3
PANASONIC PRODUCT LIMITED WARRANTY
Panasonic Canada Inc. warrants this product to be free from defects in
materials and workmanship and agrees to remedy any such defect for a
period as stated below from the date of original purchase.
CAR AUDIO PRODUCT – ONE (1) YEAR, PARTS AND LABOUR
(The labour to install or remove the product is not warranted)
LIMITATIONS AND EXCLUSIONS
This warranty does not apply to products purchased outside Canada or to
any product which has been improperly installed, subjected to usage for
which the product was not designed, misused or abused, damaged during shipping, or which has been altered or repaired in any way that
affects the reliability or detracts from the performance, nor does it cover
any product which is used commercially. Dry cell batteries are also
excluded from coverage under this warranty.
This warranty is extended to the original end user purchaser only. A purchase receipt or other proof of the original purchase date is required
before warranty service is performed.
THIS EXPRESS, LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE.
IN NO EVENT WILL PANASONIC CANADA INC. BE LIABLE FOR ANY
SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES.
In certain instances, some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, or the exclusion of
implied warranties, so the above limitations and exclusions may not be
applicable.
IF YOU SHIP THE PRODUCT TO A SERVICENTRE
Carefully pack and send prepaid, adequately insured and preferably in the
original carton.
Include details of the defect claimed, and proof of the date of original
purchase.
Folder selection order/file playback order
Root Folder
(Root Directory)
1
Points to remember when making MP3/WMA files
TEXT
Printed side
¡ High bit rate and high sampling frequency are recommended for high quality sounds.
¡ Selecting VBR (Variable Bit Rate) is not recommended
because playing time is not displayed properly and sound
may be skipped.
¡ The playback sound quality differs depending on the
encoding circumstances. For details, refer to the user
manual of your own encoding software and writing software.
¡ Direct sunlight
¡ Near car heaters
¡ Dirty, dusty and damp areas
¡ Seats and dashboards
Do not use irregularly shaped discs.
Disc cleaning
Use a dry, soft cloth to wipe from the center outward.
<Correct>
q
¡ You may encounter trouble in playing MP3/WMA files or
displaying the information of MP3/WMA files recorded with
certain writing software or CD recorders.
¡ The file extension “.mp3” or “.wma” should be assigned to
each file depending on the file format.
¡ This unit does not have the play list function.
¡ Although Multi-session recording is supported, the use of
Disc-at-Once is recommended.
Supported file systems
ISO 9660 Level 1/Level 2, Apple Extension to ISO 9660, Joliet,
Romeo
Note: Apple HFS, UDF 1.50, MIX mode CD, CD Extra is not
supported.
Compression formats
(Recommendation: “Points to remember when making
MP3/WMA files” on the right.)
¡ Windows Media
Audio Ver. 2, 8
Bit rate: 64 k-192 kbps
VBR: No
Sampling frequency:
32, 44.1, 48 kHz
e
In the order
1
–
8
3
w
File Selection
In the order
–
y
q
5
6
r
8
7
Tree 1
Tree 2
Tree 3
t
y
Tree 4
Tree 8
(Max.)
Maximum number of files/folders
¡ It is recommended to set the bit rate to “128 kbps or
more” and “fixed”.
¡ Maximum number of files: 999
¡ Maximum number of files in one folder: 255
¡ Maximum depth of trees: 8
¡ Maximum number of folders: 255 (Root folder is included.)
WMA
<Wrong>
Folder Selection
4
MP3
¡ It is recommended to set the bit rate to “64 kbps or
more” and “fixed”.
¡ Do not set the copy protect attribute on the WMA file to
enable this unit to play back.
¡ MPEG 1 audio layer 3
Bit rate: 32 k-320 kbps
VBR: Yes
Sampling frequency:
32, 44.1, 48 kHz
¡ MPEG 2 audio layer 3
Bit rate: 8 k-160 kbps
VBR: Yes
Sampling frequency:
16, 22.05, 24 kHz
2
Common
Do not use irregularly shaped discs.
Do not leave discs in the following places:
¡ You are recommended to minimize the chances of making a disc that contains both CD-DA files and MP3/WMA
files.
¡ If CD-DA files are on the same disc as MP3 or WMA files,
the songs may not play in the intended order, or some
songs may not play at all.
¡ When storing MP3 data and WMA data on the same disc,
use different folders for each data.
¡ Do not record files other than MP3/WMA files and unnecessary folder on a disc.
¡ The name of MP3/WMA file should be added by rules as
shown in the following descriptions and also comply with
the rules of each file system.
One (1) Year
Note: MP3/WMA encoding and writing software is not supplied with this unit.
¡ Do not touch the underside of a disc.
¡ Do not scratch on a disc.
¡ Do not bend a disc.
¡ When not in use, keep a disc in a case.
Recording MP3/WMA files on a CD-media
Labor
One (1) Year
Customer’s Record
Model
No.
Serial
No.
Dealer’s
No.
Code
No.
Dealer’s
Address
Date of
Purchase
Notes on MP3/WMA
How to hold a disc
¡ You may have trouble playing back some CD-R/RW discs
recorded using CD recorders (CD-R/RW drives), either due
to their recording characteristics or dirt, fingerprints,
scratches, etc. on the disc surface.
¡ CD-R/RW discs are less resistant to high temperatures and
high humidity than ordinary music CDs. Leaving them
inside a car for extended periods may damage and make
playback impossible.
¡ Some CD-R/RWs cannot be played back successfully due
to incompatibility among writing software, a CD recorder
(CD-R/RW drive) and the discs.
¡ This player cannot play the CD-R/RW discs if the session is
not closed.
¡ This player cannot play the CD-R/RW discs which contain
other than CD-DA data or MP3/WMA (Video CD, etc.).
¡ Be sure to observe the instructions of the CD-R/RW disc
for handling it.
Parts
Audio Components (except items listed below)
THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER
“LIMITED WARRANTY COVERAGE”. THE WARRANTOR IS NOT LIABLE
FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM
THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF
THIS WARRANTY. (As examples, this excludes damages for lost time,
cost of having someone remove or re-install an installed unit if applicable, travel to and from the sevicer, and loss of media, data or other memory contents. The items listed are not exclusive, but are for illustration
only.) ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE
WARRANTY OF MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF
THE LIMITED WARRANTY.
If you use commercial CDs, they must have the label
shown at right.
Some copy-protected music CDs are not playable.
Do not attach any seals or labels to your discs.
Do not write on the disc label with a ballpoint pen or
other hard-point pens.
PARTS AND SERVICE WHICH ARE NOT COVERED BY THIS LIMITED
WARRANTY ARE YOUR RESPONSIBILITY.
PANASONIC AUTO PRODUCTS
LIMITED WARRANTY
Matsushita Electric of Puerto Rico, Inc.
Panasonic Sales Company
Factory Servicenter:
Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park,
Carolina, Puerto Rico 00985
Phone (787) 750-4300, Fax (787) 768-2910
Press [DISP] to change the display.
Clock display
Adjust the hour.
CQ-C1301U
This unit is equipped with a removable face plate. Removing this face plate makes the unit totally inoperable.
Hours blinks
Q'ty: 1
Mounting Bolt
Your product is designed and manufactured to ensure the minimum of maintenance. Use a soft cloth for routine exterior cleaning. Never use benzine, thinner, or other solvents.
¡ Use fuses of the same specified rating (15 A). Using substitutes or fuses with higher ratings, or connecting the unit
directly without a fuse could cause fire or damage to the unit. If the replaced fuse fails, contact your nearest authorized
Panasonic Servicenter.
seconds.
Trim Plate
CQ-C1401U
Notes on Discs
Warning
(YEFX0217263)
Q'ty: 2
Models
This warranty gives you specific legal rights and you may also have other
rights which vary from state to state. If a problem with this product
develops during or after the warranty period, you may contact your dealer or Servicenter. If the problem is not handled to your satisfaction, then
write to warrantor’s Consumer Affairs Department at the addresses of the
warrantor.
PANASONIC SALES COMPANY,
DIVISION OF MATSUSHITA ELECTRIC OF PUERTO RICO, INC.
Ave. 65 de infanteria, Km. 9.5, San Gabriel Industrial Park
Carolina, Puerto Rico 00985
Service in Puerto Rico
THIS PRODUCT UTILIZES A CLASS I LASER.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF.
REFER SERVICING TO QUALIFIED PERSONNEL.
If the replaced fuse fails, contact your nearest authorized Panasonic Servicenter.
(clock display)
Mounting Collar
TUNE
Panasonic Consumer Electronics
Company, Division of Matsushita
Electric Corporation of America
One Panasonic Way, Secaucus,
New Jersey 07094
http://www.panasonic.com
appears.
Note: If you would like to turn on the power and make the
demonstration message appear, hold down [SRC] (PWR)
for more than 4 seconds.
The 12-hour system is used for the clock.
Clock Setting
(English: YEFM285597)
(Français: YEFM285598)
(Español: YEFM285599)
2 The demonstration screen is canceled, and no more
Press [DISP] (Display).
3 Press [SRC] (PWR: Power).
ACC
ON
2 Hold down [DISP] (CLOCK) for more than 2
Installation kit (YEP0FZ5698)
Lock Cancel Plate
tery liquid, wash it with plenty of water.
● If battery liquid comes into contact with your eyes, wash them
with plenty of water and get immediate medical attention.
Anti-Theft System
Note:
¡ Specifications and design are subject to modification without
notice due to improvements.
¡ Some figures and illustrations in this manual may be different
from your product.
Accessories
Instruction kit
Operating Instructions
new battery.
● If any part of your body or clothing comes into contact with bat-
Maintenance
: 530 kHz – 1 710 kHz
: 27 dB/µV (S/N 20 dB)
Above specifications comply with EIA standards.
In case of battery leakage
● Thoroughly wipe the battery liquid off the battery case and insert
Caution
Part 15 of the FCC Rules
Cleaning the
Unit
Tone adjustment range
: 87.9 MHz – 107.9 MHz
: 10.2 dBf. (75 Ω)
: 15.2 dBf. (75 Ω)
: 30 Hz – 15 kHz (±3 dB)
: 75 dB
: 35 dB (1 kHz)
: 55 dB
: 100 dB
: 62 dB
the battery case.
● Replace dead battery as soon as possible.
● Remove the battery from the remote control unit when not using
it for an extended period of time.
● Insulate the battery (by placing them in a plastic bag or covering
them with vinyl tape) before disposal or storage.
● Dispose of the battery according to the local regulations.
● Do not disassemble, recharge, heat or short the battery. Do not
throw a battery into a fire or water.
PANASONIC CONSUMER ELECTRONICS COMPANY,
DIVISION OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA
One Panasonic Way, Secaucus, New Jersey 07094
This operating instruction manual is for 2 models CQ-C1401U and CQ-C1301U. All illustrations throughout this manual represent model CQ-C1401U unless otherwise specified. The following table describes the differences between 2 models.
U.S.A.
● Use only specified battery (CR2025).
● Match the polarity of the battery with the (+) and (–) marks in
The following applies only in the U.S.A.
Fuse
Maximum power output
Frequency range
Usable sensitivity
50 dB quieting sensitivity
Frequency response
Alternate channel selectivity
Stereo separation
Image rejection ratio
IF rejection ratio
Signal to noise ratio
Observe the following cautions when handling the
battery for the remote control unit.
Blocking these parts will cause the interior of the unit to overheat and will result in fire or other damage.
(Anti-Theft System)
Current consumption
: DC 12 V (11 V – 16 V DC), test voltage 14.4 V, negative ground
: Less than 2.2 A (CD mode; 0.5 W 4
channels)
: 50 W x 4 (at 1 kHz), volume control
maximum
: Bass: ±12 dB at 100 Hz,
Treble: ±12 dB at 10 kHz
:4 – 8 Ω
: 2.5 V (CD mode, 1 kHz, 0 dB)
: 200 Ω
: 2.5 V (only for CQ-C1401U)
: 200 Ω (only for CQ-C1401U)
: 178 x 50 x 160 mm
{7” x 1 15/16” x 6 5/16”}
: 1.3 kg {2 lbs. 14 oz}
❑ Wear gloves for safety. Make sure that wiring is completed before installation.
❑ To prevent damage to the unit, do not connect the
power connector until the whole wiring is completed.
❑ Do not connect more than one speaker to one set of
speaker leads. (except for connecting to a tweeter)
❑ Do not block the air vent or the cooling plate of the unit.
Face Plate Removing/Mounting
Power supply
First Time Power On
FM Stereo Radio
Battery
Installation
General
The product should be installed in a horizontal position with the
front end up at a convenient angle, but not more than 30˚.
The user should bear in mind that in some areas there may be
restrictions on how and where this unit must be installed.
Consult your dealer for further details.
Use the supplied or designated parts and appropriate tools to
install the product. The use of parts other than those supplied or
designated may result in internal damage to the unit. Faulty
installation may lead to an accident, a malfunction or fire.
¡Please read these instructions (including “Limited Warranty” and “Customer Services Directory”) carefully before using this product
and keep this manual for future reference.
Preparation
❑ Installation Angle
❑ Use the designated parts and tools for installation.
FCC Warning:
Any unauthorized changes or modifications to this equipment
would void the user's authority to operate this device.
Specifications
Avoid slanted or strongly curved surfaces for installation. If the
installation is not stable, the unit may fall down while driving and
this can lead to an accident or injury.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty
lasts, so the exclusions may not apply to you.
U.S.A.
Limited Warranty
CQ-C1401U
PUSH SEL
SRC
ER
LD
FO
E/TRACK
TUN
BAND
APM
PWR
VO
L
This pictograph intends to alert you to the presence of
important operating instructions and installation instructions. Failure to heed the instructions may result in
severe injury or death.
❑ Do not install the product where it is exposed to strong
vibrations or is unstable.
Notes on MP3/WMA
CQ-C1301U
safely and to alert you to potential dangers resulting from improper
connections and operations. The meanings of the pictographs are
explained below. It is important that you fully understand the meanings of the pictographs in order to use this manual and the system
properly.
Panasonic welcomes you to our constantly growing family of electronic products owners.
We endeavor to give you the advantages of precise electronic and mechanical engineering, manufactured with carefully selected components, and
assembled by people who are proud of the reputation their work has built for our company. We know this product will bring you many hours of
enjoyment, and after you discover the quality, value and reliability we have built into it, you too will be proud to be a member of our family.
Differences
between 2 models
nents of your car audio system carefully before using the system.
They contain instructions about how to use the system in a safe and
effective manner. Panasonic assumes no responsibility for any problems resulting from failure to observe the instructions given in this
manual.
■ This manual uses pictographs to show you how to use the product
Customer Services Directory
WMA MP3 CD Player/Receiver
■ Read the operating instructions for the unit and all other compo-
Notes on CD/CD Media (CD-ROM, CD-R, CD-RW)
CQ-C1401U
Before Reading These Instructions
Safety Information
Notes on
CD-Rs/RWs
WMA MP3 CD Player/Receiver with CD Changer Control
English
®
Caution
Never assign the “.mp3”, or “.wma” file name
extension to a file that is not in the MP3/WMA
format. This may not only produce noise from
the speaker damage, but also damage your
hearing.
Notes:
¡ This unit counts the number of folders irrespective of the
presence or absence of MP3/WMA file.
¡ If the selected folder does not contain any MP3/WMA
files, the nearest MP3/WMA files in the order of playback
will be played.
¡ Playback order may be different from other MP3/WMA
players even if the same disc is used.
¡ “ROOT” appears when displaying the root folder name.
Display Information
Displayed items
¡ CD-TEXT
Disc title
Track title
¡ MP3 (ID3 tag)
Album name
¡ MP3/WMA
Folder name
File name
¡ WMA (WMA tag)
Album name
Title name/Artist name
Title name/Artist name
Displayable characters
Windows Media, and the Windows logo
are trademarks, or registered trademarks of Microsoft Corporation in the
United States and/or other countries.
¡ Name files and folders in accordance with the standard of
each file system. Refer to the instructions of writing software for details.
¡ ASCII character set and special characters in each language can be displayed.
Copyright
Notes:
¡ With some software in which MP3/WMA format files
have been encoded, the character information may not be
displayed properly.
¡ Undisplayable characters and symbols will be converted
into an asterisk ( ).
No warranty
It is prohibited by copyright laws to copy, distribute and
deliver copyrighted materials such as music without the
approval of copyright holder except enjoying yourself personally.
Above description complies with our investigations as of
December 2004. It has no warranty for reproducibility and
displayability of MP3/WMA.
MUTE
1
2
3
RANDOM
SCAN
REPEAT
4
5
6
7
8
9
0
DISP
TUNE
[MUTE]
toggles mute on/off.
TUNE
#
NUMBER
[DISP] (Display)
switches the information on display,
and exits the audio menu.
Battery Replacement
q Remove the battery holder with the Tough pointed object
remote control unit placed on a flat
surface.
q Stick your thumbnail into the
w
groove, and push the holder in
q
the direction of the arrow at the
Back side
same time.
w Pull it out in the direction of the
2
arrow using a tough pointed object.
w Put a battery in the case with (+)3
side facing up.
e Put the case back.
A track (CD mode), disc (CD changer CQ-C1401U ), file,
folder (MP3/WMA mode) and channel (XM Satellite
Radio CQ-C1401U ) can be directly selected.
Example: Track number 5
1 Press [#] (NUMBER).
2 Press [5].
3 Press [BAND] (SET).
Notes:
¡ To suspend direct selection, press [DISP].
¡ For folder selection, enter a number after pressing [#]
(NUMBER) twice.
¡ If there is no playable file in the selected folder, the first
file or folder on the disc is selected.
Warning
¡Keep batteries away from children to avoid the risk of
accidents. If an infant ingests a battery, please seek
immediate medical attention.
Caution
¡ Remove and dispose of an old battery immediately.
¡ Do not disassemble, heat or short a battery. Do not
throw a battery into a fire or water.
¡ Follow local regulations when disposing of a battery.
¡ Improper use of batteries may cause overheating, an
explosion or ignition, resulting in injury or a fire.
Functions only on Main unit
The following functions are not available on remote control
unit.
¡Demonstration
¡SQ selection
¡Scroll
¡Disc eject
SCAN
3
4
5
2
REPEAT
Power on: Press [SRC] (PWR).
Power off: Hold down [SRC] (PWR) for more
than 1 second.
1
[SRC] (Source)
selects a source.
SCROLL
RANDOM
SCAN
3
4
5
2
REPEAT
CLOCK
SQ
DISP
6
[1] to [6]
selects a preset station in the radio source,
and presets the current station. (Hold it down
for more than 2 seconds.)
[DISP] (Display)
switches the information on
the display.
Disc Player
(POP) wide-ranged and deep sound:
slightly emphasizes bass and treble.
CQ-C1401U
(VOCAL) clear sound:
emphasizes middle tone and slightly emphasizes treble.
Volume Adjustment
(Setting Range: 0 to 40, Default: 18)
Turn [VOL].
BAND
Radio mode display (Default)
1 Press [SRC] to select the radio source.
2 Press [BAND] to select a band.
Note: Settings of SQ, bass and treble are influenced one
ON: Press [MUTE]. (
OFF: Press [MUTE] again.
Manual station preset
RANDOM
SCAN
3
4
5
REPEAT
SQ
CLOCK
DISP
6
[DISP] (Display)
switches the information on
the display.
[}] [{]
skip to the previous/next disc in CD changer mode
indicator
(RANDOM)/(SCAN)/(REPEAT)
toggles on/off each play mode.
(SCROLL)
scrolls the information on display.
(CD/MP3/WMA mode)
CQ-C1401U ,
and skip to the previous/next folder in MP3/WMA
mode.
Press [DISP] to change the display.
MP3/WMA mode display
Normal
Normal
Disc title
Play time
Folder name/
Album*
File name/
Title, artist*
Clock
Track title
lights when folder random/repeat/scan is on.
Folder number
Clock
File number
CQ-C1401U
CD Changer:
Play Mode indicators
Normal
CD Changer mode display
Track number
*ID3/WMA Tag On/Off
1 Press [SRC] to select the Disc Player
source.
2
Select a desired portion.
[BAND]
selects a band in the XM Satellite
Radio source.
(Category)
toggles on/off the category mode.
(Hold it down for more than 2 seconds.)
(blinks once)
Note: New stations overwrite existing saved stations.
Disc number
Clock
album title and song
title/artist name are displayed.
[SRC] (Source)
selects a source.
Folder/disc selection
Notes:
¡ For scrolling text, press [3] (SCROLL).
¡ “NO TEXT” is displayed when there is no information on the
disc.
¡ This unit does not support CD text display. (CD changer mode)
CQ-C1401U
Random play
All the available tracks/files are played in a random sequence.
Repeat play (folder/disc)
The current folder/disc is repeated.
Disc Player (CD-DA disc):
Previous/next track
Pause
Press [BAND] (y / 5).
Disc Player (MP3/WMA disc):
Press again to cancel.
Previous/next file
Note: Pausing does not function in the CD changer
mode.
CQ-C1401U
CD Changer:
Previous/next track
Random play (folder/disc)
All the available files/tracks in current folder/disc are played in
a random sequence.
Hold down [4] (RANDOM) for more than 2
seconds.
Hold down again to cancel.
Repeat play
The current track/file is repeated.
Press [6] (REPEAT).
Press again to cancel.
Hold down [6] (REPEAT) for more than 2
seconds.
SCROLL
RANDOM
SCAN
3
4
5
2
It is required to sign up to become an XM Satellite Radio subscriber. After checking your XM Satellite Radio ID, sign up on
the XM’s website or by calling them.
REPEAT
SQ
6
DI S C
D·M
CLOCK
DISP
q : Increased
w : Decreased
Treble
q : Increased
w : Decreased
(Setting Range: –12 dB to +12 dB by 2 dB,
Default: 0 dB)
Balance
q : Right enhanced
w : Left enhanced
(Setting Range: 15 levels each, Default CNT (center))
Note: New stations overwrite existing saved stations.
Fader
q : Front enhanced
w : Rear enhanced
(Setting Range: 15 levels each, Default CNT (center))
q : Increased
w : Decreased
Troubleshooting
[DISP] (Display)
switches the information on
the display.
If You Suspect Something Wrong
Hold down again to cancel.
¡ Write down the ID indicated on the lower right of your XM
receiver (XMD1000).
Press again to cancel.
Scan play (folder/disc)
From the next folder/disc, the first 10 seconds of the first
file/track in each album is played in sequence.
Hold down [5] (SCAN) for more than 2 seconds.
Hold down again to cancel.
XM RADIO ID
Radio source.
The first 10 seconds of each tracks/files is played in sequence.
Press [5] (SCAN).
XM RADIO ID : XXXXXXXX
1 Press [SRC] to select the XM Satellite
Scan play
[]] [[]
select a channel.
[}] [{]
select a category in the category mode.
¡ Check the ID shown by tuning your XM Radio to chan-
nel 0. (Refer to “Channel adjustment”)
1 Check of XM Satellite Radio ID.
L/C 1144XXXXXX
Operation Flow
Note: To perform fast forward/reverse, hold down
either of them.
Previous/next disc
Press again to cancel.
Random, Repeat, Scan
Operation Flow
Press [6] / [7].
Press [4] (RANDOM).
CQ-C1401U
CD Changer:
MUTE
[1] to [6]
selects a preset channel in the XM Satellite
Radio source,
and presets the current channel. (Hold it
down for more than 2 seconds.)
XMD 1000
Track/file selection
ER
LD
FO
CQ-C1401U
1
(Default)
folder name/file name are
displayed.
Play time
Disc Player (MP3/WMA disc):
q : Up
w : Down
(Setting Range: –12 dB to +12 dB by 2 dB,
Default: 0 dB)
Display change
Band
Preset Number
Press [DISP] to change the display.
Band/channel
Channel name
Check and take steps as described below.
If the described suggestions do not solve the problem, it is recommended to take the unit to your nearest authorized Panasonic
Servicenter. The product should be serviced only by qualified personnel. Please refer the checking and the repair to professionals.
Panasonic shall not be liable for any accidents arising out of neglect
of checking the unit or your own repair after your checking.
2 Press [BAND] to select a band.
(RADIO ID display)
2 Activate the XM Satellite Radio.
Select either of the below to sign up.
¡ Web site: http://www.xmradio.com/activation
¡ Phone number: 1-800-852-9696
Warning
¡ Do not use the unit in an irregular condition, for example, without sound, or with smoke or a foul smell, which can cause
ignition or electric shock. Immediately stop using the unit and
consult your dealer.
¡ Never try to repair the unit by yourself because it is dangerous
to do so.
Channel
Artist name
Song name
XM Satellite Radio indicator
Common
Category name
Clock time
Up to 6 channels can be preset in XM1, XM2, and XM3 respectively.
Preset channels can be simply called up by pressing [1] to
[6].
1
2 Hold down [1] to [6] for more than 2 secSelect a channel.
Notes:
¡ New channels overwrite existing saved channels.
¡ Because preset memory setting is performed with service
IDs in each channel, a channel may switch to another that
has been stored under the same service ID when calling up
a preset channel. However, broadcasting contents are the
same as what the stored channel provides.
No power
No sound
Noise
No sound from
left, right, front,
or rear speaker
onds.
Left and right
sounds are
reversed
(blinks once)
Check point
Trouble
CQ-C1401U
Play Mode indicators (blinks when disc random/repeat is
on)
Previous/next folder
PWR
SRC
¡ Do not insert foreign objects into the disc slot.
Press [{] / [}].
BAND
APM
VO
L
Hold down [3] for more
than 2 seconds.
Caution
¡ Do not insert a disc when the
indicator lights.
¡ Refer to the section of “Notes on Discs” and “Notes
on MP3/WMA”.
¡ This unit does not support 8 cm {3”} discs.
¡ If you insert an 8 cm {3”} disc and cannot eject it, turn ACC of
your car off once and turn it on again, then press [u] (Eject).
About XM
The direct satellite-to-receiver broadcasting technology is used to provide
listeners with crystal clear sound smoothly from coast to coast. XM is over
130 channels of sheer variety: digital-quality music, news, sports, comedy,
traffic & weather, talk, children’s programs, and more.
The XM name and related logos are trademarks of XM Satellite
Radio Inc.
PUSH SEL
[SRC] (Source)
selects a source.
SCROLL
2
wise to adjust.
Bass
[1] to [6] for more than 2 seconds.
The preset stations under best receiving conditions are
received for 5 seconds each after presetting the stations
(SCAN). To stop scanning, press one of the buttons from
[1] to [6].
XM Satellite Radio Source Display
1
3 Turn [VOL] clockwise or counterclock-
(Setting Range: 0 to 40, Default: 18)
1 Tune into a station.
2 Hold down one of the preset buttons from
CQ-C1401U
Channel Preset
MUTE
DISP
Subwoofer Level
No sound, or disc
is automatically
ejected
3 Select a channel.
Channel adjustment
[]]: Lower
[[]: Higher
Note: Channel selection is not available during the recep-
tion of channel 1 with category ON. To receive other channels, set the category to OFF or switch to another category.
Preset channel selection
Press the corresponding preset button from [1] to [6] to
tune in a preset channel.
Category On/Off
Category Selection
1
1
Hold down [BAND] to switch category
mode ON or OFF.
The following functions are available when the category mode
is active.
¡ Enables category switching.
¡ Enables channel selection only within the category selected
by category switching.
Press [}] or [{] to display the category
name.
2 Press [}] or [{] while the category name
is displayed. Seeking will start.
Check point
Trouble
Radio
● Start the engine. (Or turn the ignition
switch to the ACC position.)
● Verify the wiring. (battery lead, power
lead, ground lead, etc.)
● Fuse blown (Contact the nearest
Panasonic Servicenter.)
● Ask a professional for fuse replacement.
● Be sure to use the same rated fuse.
● Disable the mute function.
● Verify the wiring.
● Wait until the dew disappears before
turning on the unit.
Frequent
noise
● Tune in to another station of high-intensity waves.
● Make sure that the antenna mounted
point is grounded properly.
Preset data
deleted
● The preset memory is cleared to return
to the original factory setting when the
power connector or battery is disconnected.
Error Display Messages
● Make sure that grounding is established
(The disc is ejected automatically.)
The disc is dirty, or is upside down.
● Check the disc.
● Adjust the balance and fader.
● Verify the wiring.
(The disc is ejected automatically.)
The disc has scratches.
● Check the disc.
properly.
No operation by some cause.
● If normal operation is not restored, consult your dealer or the nearest
Servicenter to ask for repairs.
● Connect the speaker lead correctly.
Cannot read the file
● Check the file.
Disc Player
Category Setting
SRC
CLOCK
SQ
6
(Setting Range: –6 dB to +6 dB and MUTE,
Default: 0 dB)
CQ-C1401U
E/TRACK
TUN
PWR
Play time
Play Mode indicators
DI S C
D·M
REPEAT
Volume
Up to 6 stations can be preset in AM, FM1, FM2, and FM3
respectively.
Preset stations can be simply called up by pressing [1] to [6].
Press the corresponding preset button from [1] to [6] to
tune in a preset station.
Preparation:
¡ You can connect the optional XM receiver (XMD1000) with
optional Digital Adapter (XMDPAN100). For details, refer to the
operating instructions for the XM receiver.
¡ Toll free number
XM Tuner P/N: XMD1000
Call 1-800-XM-RADIO(96-72346)
Extension cord P/N: XMDPAN100 Call 1-800-942-TERK(8375)
Getting Started
APM
ER
LD
FO
CQ-C1401U
Display change
Disc Player (CD-DA disc): Disc Player (MP3/WMA disc):
Player Source Display
VO
L
E/TRACK
TUN
BAND
PUSH SEL
(y / 5) (Pause/Play)
toggles pause/play in the
player source.
5
Note: If the fader is set to front, the pre-amp. output
(rear) is decreased.
CD-DA mode display
[u] (Eject)
ejects the disc.
SCAN
4
Note: If no operation takes place for more than 7 seconds in the audio menu (2 seconds in Main volume adjustment), the display returns to the regular mode.
Preset station selection
XM Satellite Radio
Track number
RANDOM
3
lights.)
Player (Disc Player and CD Changer)
[6] [7]
skip to the previous/next track/file in the player mode.
Hold down either of them for fast reverse/fast
forward.
SCROLL
1 Press [VOL] (PUSH SEL) to display the audio menu display.
Battery Type: Panasonic lithium battery (CR2025) (Included
in the remote control)
Battery Life: Approximately 6 months under normal use (at
room temperature)
Disc slot
takes a disc in with the printed side facing up.
Notes:
¡ The power will be turned on automatically when
a disc is loaded.
¡ A disc which has both CD-DA data and
MP3/WMA data on it may not be reproduced
normally.
2
[DISP] (Display)
exits from the audio menu.
another. If such an influence causes distortion to the
audio signal, readjust bass/treble or volume.
Mute
MUTE
DI S C
D·M
Clock display
seconds.
Note: Hold down either of them for more than 0.5 seconds and release it for seek tuning.
PWR
mode to be adjusted.
3 Select a station.
[TUNE]]: Lower
[TUNE[]: Higher
ER
LD
FO
CQ-C1401U
1
1 Select a band.
2 Hold down [BAND] (APM) for more than 2
Frequency adjustment
VO
L
SRC
With this operation, stations with good receiving conditions can
be automatically stored in the preset memory.
(ROCK) speedy and heavy sound:
exaggerates bass and treble.
CD Changer
or
XM radio
Press [DISP] to change the display.
APM
Auto Preset Memory (APM)
(FLAT) flat frequency response:
does not emphasize any part. (Default)
Press [SRC] to change the source.
Frequency Preset Number
2 Press [VOL] (PUSH SEL) to select a
[TUNE ]] [TUNE []
down/up the frequency. (Hold it down for
more than 0.5 seconds and release it for seek
tuning.)
SQ is a function that can call up various sound types at
the touch of button in accordance with your listening
music type.
Press [SQ] to select the sound type as follows:
Source Selection
Notes: Battery Information:
MUTE
SRC
DI S C
D·M
SQ (Sound Quality)
Set your car's ignition switch to the ACC or ON position.
Radio
PWR
DISP
[SQ] (Sound Quality)
selects a sound type (SQ).
ER
LD
FO
CQ-C1401U
APM
CLOCK
SQ
6
[MUTE]
toggles mute on/off.
Power On/Off
General Operations
Direct Access
[SRC] (Source)
selects a source.
(PWR) (Power)
toggles power on/off.
RANDOM
VO
L
Station Preset
BAND
1
SCROLL
BAND
Operation Flow
VOL
SET
MUTE
SRC
DI S C
D·M
PUSH SEL
PUSH SEL
APM
[VOL] (volume)
adjusts the volume,
and selects the value in the audio menu, etc.
E/TRACK
TUN
CQ-C1401U
PWR
SEL
ER
LD
FO
L
E/TRACK
TUN
VO
BAND
POWER
SOURCE MENU
SRC
Band
[VOL]
selects a value in the audio menu.
(PUSH SEL) (Push to Select)
selects items in the audio menu.
Display change
E/TRACK
TUN
Remote Control Sensor
[MENU] (SEL: Select)
selects the items in the audio menu.
[SRC] (SOURCE)
selects a source.
(POWER)
toggles power on/off.
CAR AUDIO
Functions
[VOL] (Volume)
lights while receiving an FM stereo signal.
PUSH SEL
[BAND]
selects a band in the tuner source,
toggles pause/play in player source,
executes the APM in tuner source (Hold it down for more than 2 seconds),
toggles category mode on/off in the XM Satellite Radio source CQ-C1401U .
[BAND]
selects a band in the radio source.
(APM) (Auto Preset Memory)
executes APM in the radio source. (Hold it
down for more than 2 seconds.)
Radio Source Display
Note: This instruction manual explains operations for use with the buttons on the main unit. (Different operations excluded)
[0] to [9]
selects a preset station/channel (1 to 6),
presets the current station/channel (Hold it down
for more than 2 seconds.),
inputs the number in direct selection.
[#] (NUMBER)
executes the direct selection.
[RANDOM] [SCAN] [REPEAT]
toggles on/off each play mode.
[]] [[]
down/up the frequency (Hold it down for more
than 0.5 seconds and release it for seek tuning.),
selects a channel.
[{] [}]
skip to the previous/next folder/disc in player
mode,
selects a category.
[6] [7]
skip to the previous/next track/file in player mode.
Hold it down for fast reverse/fast forward.
Audio Settings
Radio (AM/FM)
Audio menu
General
Remote Control Unit
● Load the disc correctly.
● Clean the disc.
Sound skip,
poor sound
quality
● Clean the disc.
Sound skip
due to
vibration
● The maximum permissible tilt angle is
30°.
● Secure the unit.
Disc
unejectable
● Press [u]. If the disc is still not ejected,
contact the nearest Panasonic
Servicenter.
Note: Messages in the action and display sections of the error chart
vary with changers. Refer to the operating instructions for the CD
changer for details. CQ-C1401U
A WMA file can be copyrighted.
● The file protected by copyright is not
playable.
CQ-C1401U
DIN cord is disconnected.
● Connect the DIN cord.
No disc is in the CD Changer (magazine).
Cannot receive XM Satellite Radio.
● Verify the wiring.
Channel not in service
● This channel is not currently in
service. Tune to another channel.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising