Toshiba MV19N2 19 in. TV/VCR Combo

Toshiba MV19N2 19 in. TV/VCR Combo
OWNER’S MANUAL
TELEVISION/VCR COMBINATION
MV13N2/W
MV19N2/W
ATTENTION
If you purchase a universal remote control from your local retailer, please
contact the remote manufacturer for the required programming code.
TV/CATV MODE SELECTION
When shipped from the factory, the TV/CATV menu option is set to the “CATV”
(Cable Television) mode.
If not using CATV, set this menu option to the “TV” position.
Before operating the unit, please read this manual thoroughly.
5E20101B COV-IN
1
14/08/2003, 15:49
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
WARNING:
TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead
symbol, within an equilateral triangle is
intended to alert the user to the presence
of uninsulated dangerous voltage within
the product's enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock.
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in
the literature accompanying the appliance.
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC (Federal Communications Commission) Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the distance between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance with the
FCC (Federal Communications Commission) Rules could void the user's authority to operate this
equipment.
COPYRIGHT: It is permissible to record television programs, films, video tapes and other material only in the event
that third party copyrights and other rights are not violated.
WARNING: Unauthorized recording of copyrighted television programs, films, video cassettes and other materials
may infringe the rights of copyright owners and be contrary to copyright laws.
5E20101B COV-IN
2
14/08/2003, 15:49
IMPORTANT SAFEGUARDS
1.
READ INSTRUCTIONS
2.
All the safety and operating instructions should be read before the unit is operated.
RETAIN INSTRUCTIONS
3.
The safety and operating instructions should be retained for future reference.
HEED WARNINGS
4.
All warnings on the unit and in the operating instructions should be adhered to.
FOLLOW INSTRUCTIONS
5.
All operating and use instructions should be followed.
CLEANING
Unplug this unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
6.
Use a damp cloth for cleaning the exterior cabinet only.
ATTACHMENTS
The manufacturer of this unit does not make any recommendations for attachments, as they may cause hazards.
7.
WATER AND MOISTURE
Do not use this unit near water. For example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet
basement, or near a swimming pool.
PORTABLE CART WARNING
(symbol provided by RETAC)
8. ACCESSORIES
Do not place this unit on an unstable cart, stand, tripod, bracket, or table.
The unit may fall, causing serious injury, and serious damage to the unit.
8A. An appliance and cart combination should be moved with care. Quick stops,
excessive force, and uneven surfaces may cause the appliance and cart
combination to overturn.
S3126A
VENTILATION
Slots and openings in the cabinet back or bottom are provided for ventilation, and to ensure reliable operation of
the unit, and to protect it from overheating. These openings must not be blocked or covered. The openings
should never be blocked by placing the unit on a bed, sofa, rug, or other similar surface. This unit should never
be placed near or over a radiator or heat source. This unit should not be placed in a built-in installation such as
a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.
10. POWER SOURCE
9.
This unit should be operated only from the type of power source indicated on the rating plate. If you are not sure
of the type of power supply to your home, consult your appliance dealer or local power company. For units
intended to operate from battery power, or other sources, refer to the respective pages on this Owner’s Manual
for their operating instructions.
11. GROUNDING OR POLARIZATION
This unit is equipped with a polarized alternating-current line plug (a plug having one blade wider than the other).
This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug
fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your
obsolete outlet. Instead of the polarized alternating-current line plug, your unit may be equipped with a 3-wire
grounding-type plug (a plug having a third (grounding) pin). This plug will only fit into a grounding-type power
outlet. This too, is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to
replace your obsolete outlet.
Do not defeat the safety purpose of the grounding-type plug.
1
5E20101B P01-09
1
14/08/2003, 15:49
IMPORTANT SAFEGUARDS
(CONTINUED)
12. POWER-CORD PROTECTION
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point
where they exit from the appliance.
13. LIGHTNING
To protect your unit from a lightning storm, or when it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the unit
due to lightning and power line surges.
14. POWER LINES
An outside antenna system should not be located in the vicinity of overhead power lines, other electric light or
power circuits, or where it can fall onto or against such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from touching such power lines or circuits, as contact
with them might be fatal.
15. OVERLOADING
Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.
16. OBJECT AND LIQUID ENTRY
Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short out
parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit.
17. OUTDOOR ANTENNA GROUNDING
If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is grounded
to provide some protection against voltage surges and built-up static charges, Section 810 of the National
Electrical Code (NEC), ANSI/NFPA 70, provides information with respect to proper grounding of the mast and
supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding
electrode.
18. SERVICING
Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage
or other hazards. Refer all servicing to qualified service personnel.
For example:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the unit.
c. If the unit has been exposed to rain or water.
d. If the unit does not operate normally by following the operating instructions. Adjust only those controls that are
covered by the operating instructions, as an improper adjustment of other controls may result in damage and
will often require extensive work by a qualified technician to restore the unit to its normal operation.
e. If the unit has been dropped or the cabinet has been damaged.
f . When the unit exhibits a distinct change in performance, this indicates a need for service.
19. REPLACEMENT PARTS
When replacement parts are required, be sure the service technician uses replacement parts specified by the
manufacturer or those that have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock or other hazards.
2
5E20101B P01-09
2
14/08/2003, 15:49
20. SAFETY CHECK
Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to
determine that the unit is in proper operating condition.
21. HEAT
The product should be situated away from heat sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
22. NOTE TO CATV SYSTEM INSTALLER
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides
guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the
grounding system of the building, as close to the point of cable entry as practical.
EXAMPLE OF ANTENNA GROUNDING AS PER THE
NATIONAL ELECTRICAL CODE
ANTENNA LEAD IN WIRE
GROUND CLAMP
ANTENNA DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
NEC-NATIONAL ELECTRICAL CODE
S2898A
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
IMPORTANT RECYCLING INFORMATION
This product uses both Cathode Ray Tube (CRT) and other components
that contain lead. In your community there might be regulations that
require you to dispose these materials properly under environmental
considerations. Please contact your local authorities, or the Electronic
Industries Alliance (http://www.eiae.org) for disposal or recycling
information.
3
5E20101B P01-09
3
14/08/2003, 15:49
FEATURES
Color TV With Video Cassette Recorder - Unique space saving design combines a color TV and a video cassette
recorder.
High Quality Picture Technology - This TV/VCR equipped “HQ” incorporates VHS High Quality technology. A built-in detail
enhancer is used to boost the recorded signal and provide picture quality during playback. It is compatible with other VHS
video cassette recorders.
181 Channel Tuner - Receives standard VHF and UHF broadcast channels and up to 113 cable channels. The actual
number of channels received depends upon channel reception in your area or your cable system.
Closed Caption Decoder With Full Text Mode - Displays text captions or full screen text on the screen for hearing
impaired viewers.
8-Programs/1-Month Programmable Timer With Everyday/Every Week Capability - The built-in timer allows automatic
absentee recording of up to 8 TV programs within 1 month. It is also possible to record a program which is broadcast at the
same time everyday or every week.
Automatic Clock Set - Once your TV/VCR is plugged into the AC outlet, it automatically sets the correct date and time.
On-Screen TV Display And VCR Programming - When you select a channel or make other changes, the TV will show an
indicator on the screen for a few seconds. Timer recording can be programmed and confirmed on the screen.
Picture Adjustments Using The Remote Control - The On-Screen display allows remote control adjustment of BRIGHTNESS, CONTRAST, COLOR, TINT and SHARPNESS.
Automatic Playback/Rewind-Stop-Eject - When loading a cassette tape without the erase prevention tab, this TV/ VCR
will automatically play back the cassette tape at the correct speed. When a tape reaches its end during play-back, recording
(except during OTR and Timer Record) and fast forward, it will automatically stop, rewind, stop and eject the tape.
Programmable ON/OFF Timer - Allows you to automatically turn on or off the TV/VCR at a set time.
Programmable TV Sleep Timer - Operable from the remote control, the TV can be programmed up to 120 minutes to turn
off automatically.
Automatic Repeat Play System - When Auto Repeat option is turned on, the TV/VCR will automatically play back the
same cassette tape repeatedly.
One-touch Timer Recording (OTR) - Simply by pressing the REC buttons, the TV/VCR can be programmed for up to 6
hours of recording with an immediate start.
Front Audio/Video Input Jacks - Input jacks for other video device or playback purpose.
Skip Search - When the SKIP SEARCH button on the remote control is pressed during playback, the TV/VCR will automatically search forward in 30 second increments to a maximum of 3 minutes with each press of the SKIP SEARCH button,
and then return to normal playback.
2 Speed Picture Search - 3 or 5 times normal speed in SP mode (9X or 15X in SLP).
2 Speed Record Playback - Records and plays two tape speeds (SP, SLP).
Real Time Tape Counter With Zero Return - The counter displays the real tape time and the zero return can be used to
return the tape to a preselected position (00:00:00) while the counter can be used to locate programs.
Digital Auto Tracking - Automatically adjusts tracking during playback for the best possible picture.
On-Screen 3 Language Display - You can select one of 3 languages, English, Spanish or French for on-screen programming.
V-Chip - The V-Chip function can read the rating of a TV program or movie content if the program is encoded with this
information. V-Chip will allow you to set a restriction level.
4
5E20101B P01-09
4
14/08/2003, 15:49
TABLE OF CONTENTS
Please read the descriptions and operating procedures contained in this Owner’s Manual prior to operating
your new TV/VCR.
PREPARATION
SAFETY PRECAUTIONS ....................................................................................................................................... 6
LOCATION OF CONTROLS ................................................................................................................................... 8
REMOTE CONTROL .............................................................................................................................................. 9
ANTENNA CONNECTIONS ................................................................................................................................... 11
CABLE TV CONNECTIONS ................................................................................................................................. 13
SETTING THE LANGUAGE ................................................................................................................................. 14
AUTO CLOCK SETTING ...................................................................................................................................... 15
MANUAL CLOCK SETTING ................................................................................................................................. 17
TV OPERATION
TV OPERATION ....................................................................................................................................................
TO MEMORIZE CHANNELS ................................................................................................................................
SETTING THE V-CHIP .........................................................................................................................................
TO SET THE ON TIMER .......................................................................................................................................
TO SET THE OFF TIMER .....................................................................................................................................
PICTURE CONTROL ADJUSTMENTS ................................................................................................................
18
22
25
29
30
31
PLAYBACK
LOADING AND UNLOADING A VIDEO CASSETTE ............................................................................................ 33
PLAYBACK ........................................................................................................................................................... 35
SPECIAL PLAYBACK ........................................................................................................................................... 37
RECORDING
RECORDING A TV PROGRAM ............................................................................................................................
ONE-TOUCH TIMER RECORDING (OTR) ..........................................................................................................
TIMER RECORDING ............................................................................................................................................
OTHER FUNCTIONS FOR THE TIMER RECORDING ........................................................................................
39
41
42
44
ADDITIONAL INFORMATION
USING THE REAL TIME TAPE COUNTER ..........................................................................................................
USING ZERO RETURN ........................................................................................................................................
DUPLICATING A VIDEO TAPE .............................................................................................................................
PROBLEM AND TROUBLESHOOTING GUIDE ...................................................................................................
RECEPTION DISTURBANCES ............................................................................................................................
VIDEO HEAD CLEANING .....................................................................................................................................
SPECIFICATIONS ................................................................................................................................................
LIMITED WARRANTY ..........................................................................................................................................
45
46
47
48
50
51
51
52
5
5E20101B P01-09
5
14/08/2003, 15:49
SAFETY PRECAUTIONS
MOISTURE CONDENSATION
DO NOT OPERATE ANY FUNCTIONS ON THIS UNIT FOR AT LEAST THREE HOURS WHEN MOISTURE IN
THE AIR CONDENSES ON IT. LET THE UNIT STAND WITH POWER ON (SEE BELOW).
WHAT IS MOISTURE CONDENSATION?
When a cold liquid is poured into a glass, for example, water vapor in the air will condense on the surface of
the glass. This is called moisture condensation.
MOISTURE WILL CONDENSE ON THE UNIT IN THE FOLLOWING CASES;
• When you move the unit from a cold to a warm place.
• After heating a cold room or under extremely humid conditions.
WHEN YOU EXPERIENCE THE ABOVE CONDITIONS,
Plug the power cord into an AC outlet, press the POWER button to turn on
and leave the unit at room temperature until moisture condensation disappears.
Depending on the surrounding conditions, this may take about three hours.
If you cause a static discharge when touching the
unit, and the unit fails to function, simply unplug the
unit from the wall outlet, wait a few minutes and
plug it back in. The unit should return to normal
operation.
Avoid extreme heat.
Do not place the unit on or near appliances which may
cause electromagnetic interference (e.g. speakers,
etc). Doing so may cause erratic operation of the unit
including picture and/or sound distortion or noise.
Avoid extreme cold.
Head Drum
Video Tape
104˚F
(40˚C)
(5˚C)
41˚F
Avoid extreme moisture and dust.
The ventilation holes prevent overheating. Do not
block or cover these holes. Especially avoid
covering the holes with soft materials such as cloth
or paper.
6
5E20101B P01-09
6
14/08/2003, 15:49
Do not insert fingers or any other objects into the
cassette loading slot. Do not spray cleaner or wax
directly on the unit or use forced air to remove dust.
Avoid places subject to strong vibration. Use in
a horizontal (flat) position only.
Keep the unit away from flower vases, sinks, etc.
If liquids should be spilled into the unit, serious
damage will result. If you spill any liquids into the
unit, unplug the AC power cord immediately and
consult qualified service personnel before attempting to use it again.
When you finish operating the unit, always unload
the cassette and turn off the power.
When you leave your home for a long time, unplug
the AC power cord.
To protect the unit from a lightning storm, unplug the
AC power cord from the wall outlet and disconnect
the antenna.
POWER SOURCE
TO USE AC POWER
Use the AC polarized line cord provided for operation on AC. Insert
the AC cord plug into a standard 120V 60Hz polarized AC outlet.
NOTES:
• Never connect the AC line cord plug to anything other than the
specified voltage (120V 60Hz). Use the attached power cord only.
• If the polarized AC cord does not fit into a nonpolarized AC outlet,
do not attempt to file or cut the blade. It is the user's responsibility
to have an electrician replace the obsolete outlet.
• If you cause a static discharge when touching the unit, and the
unit fails to function, simply unplug the unit from the AC outlet, wait
a few minutes, and plug it back in. The unit should return to
normal operation.
• If the AC cord plug is plugged in for the first time, wait for about 5
seconds before pressing the POWER button.
5E20101B P01-09
7
Wider Hole
and Blade
AC Outlet
Polarized AC Cord Plug
(One blade is wider than the other)
14/08/2003, 15:49
7
LOCATION OF CONTROLS
FRONT
REAR
1
ANT.
(MV13N2/W)
2
3 4
6
5
15
7
16
POWER
TIMER REC
8
REC
REC
VOLUME
9
10
CHANNEL
11
PLAY
STOP/EJECT
REW
FF
12
13
LINE IN
VIDEO
AUDIO
PHONE
14
DESCRIPTION OF CONTROLS
FRONT:
1. Cassette Loading Slot - To insert or remove a
video tape.
2. POWER Button - Press to turn the TV/VCR on or off.
3. TIMER REC Indicator - Lights when the unit is in
the Timer Record Mode.
4. REC Indicator - Lights up when the TV/VCR is
recording.
5. PLAY Button - Press to play a prerecorded tape.
6. REW (Rewind) Button - In the Stop mode, this
button rapidly winds the tape backwards. In the Play
mode, this button activates reverse search.
7. PHONE Jack - Plug monaural headphones or an
earphone with an 1/8” miniplug into this jack for
private listening.
8. Remote Sensor - Signals from the Remote Control
are received here.
9. REC Button - Press once to start normal recording.
Additional presses activate One-touch Timer
Recording.
10. VOLUME ▲ / ▼ Buttons - Press to raise or lower
the volume of the sound.
11. CHANNEL ▲ / ▼ Buttons - Press to select a
channel for viewing or recording.
12. STOP/EJECT Button - Press once to stop the tape
in any mode. Press again to eject the tape.
13. FF (Fast Forward) Button - In the Stop mode, this
button rapidly winds the tape forward. In the Play
mode, this button activates forward search.
14. AUDIO/VIDEO IN Jacks - Audio and video signal
cables from an external source can be connected
here.
REAR:
15. UHF/VHF Antenna Jack - Connect the 75 ohm
coaxial cable from the antenna or Cable TV service
to this jack.
16. AC Power Cord - Connect to a 120V, 60Hz outlet.
8
5E20101B P01-09
8
14/08/2003, 15:49
REMOTE CONTROL
1
8
16
22
2
9
23
3
10
4
11
12
24
17
25
18
26
13
19
5
27
14
20
6
15
21
28
7
DESCRIPTION OF CONTROLS
1. CLOSED CAPTION Button - Switches between Caption,
Text and TV modes for Closed-Captioned programs.
2. Direct Channel Selection Buttons (0-9) - Allows direct
access to any channel.
3. CALL Button - Displays the present time/day of the
week, channel, counter, speed selection (and VCR
mode if VCR is operating) on the TV screen.
4. MENU Button - Press to display the On-Screen menu
function.
5. PROGRAM Button - Press to confirm the programmed
timer recording and ON/OFF timer.
6. PLAY Button - Press to play a prerecorded tape.
7. EJECT Button - Press to eject the tape.
8. POWER Button - Press to turn the TV/VCR on. Press
again to turn the TV/VCR off.
9. SKIP SEARCH Button - Press in the playback mode to
search forward in 30 second increments to a maximum
of 3 minutes.
10. ZERO RETURN Button - Use to stop the tape when
the counter reaches 00:00:00.
11. CANCEL Button - Used to clear the selected program
and to move the cursor backward.
12. SP/SLP Button - Sets the tape speed for recording.
13. CHANNEL + / – Buttons - Press the + button to
change to a higher numbered channel set into memory.
Press the – button to change to a lower numbered
channel set into memory.
14. TIMER REC Buttons - Used to set the TV/VCR to start
recording at a preset time.
15. FF (Fast Forward) Button - In the Stop mode, this
button rapidly winds the tape forward. In the Play mode,
this button activates forward search.
5E20101B P01-09
9
16. SLEEP Button - Sets the TV to turn off automatically
after up to 120 minutes.
17. DIGITAL TRACKING Button - Allows automatic
adjustment of tracking to minimize picture noise during
playback.
18. SET/TR + / – Buttons - Used to set or adjust in the
menu mode. During playback, they are used to adjust
tracking manually.
19. VOLUME + / – Buttons - Press the + button to increase, or the – button to decrease the volume level.
20. REC Buttons - Press both buttons at the same time
once to start normal recording. Additional presses
activate One-touch Timer Recording.
21. REW (Rewind) Button - In the Stop mode, this button
rapidly winds the tape backwards. In the Play mode,
this button activates reverse search.
22. INPUT SELECT Button - Switches the program for
viewing between the TV/VCR and external input
sources.
23. COUNTER RESET Button - Used to reset the counter
to 00:00:00.
24. CHANNEL RETURN Button - Switches between the
present channel and the last channel selected.
25. MUTE Button - Press to turn off the sound. Press
again to turn the sound back on.
26. ENTER Button - Press to enter or select information
for on-screen operations.
27. PAUSE/STILL Button - During recording, this button
temporarily stops the tape. During playback, it stops the
tape and displays a still image on the TV screen.
28. STOP Button - Press once to stop the tape.
9
14/08/2003, 15:49
REMOTE CONTROL
(CONTINUED)
BATTERY INSTALLATION
1
2
Slide the battery compartment cover in the direction
of the arrow.
Install two “AAA” batteries,
paying attention to the
polarity diagram in the
battery compartment.
3
Replace the compartment
cover.
BATTERY PRECAUTIONS
The precautions below should be followed when using batteries in this device:
1. Use only the size and type of batteries specified.
2. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment.
Reversed batteries may cause damage to the device.
3. Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones.
4. If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury
from possible battery leakage.
5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture (Follow battery
manufacturer’s directions).
EFFECTIVE DISTANCE OF THE REMOTE CONTROL
15 FEET
NOTES:
•
•
•
When there is an obstacle between the TV/VCR and the remote control, the remote control may not
operate.
When direct sunlight, an incandescent lamp, fluorescent lamp or any other strong light shines on the
Remote sensor of the TV/VCR, the remote operation may be unstable.
When using the remote control, press the button at intervals of about 1 second to ensure the correct
mode of operation.
10
5E20101B P10-19
10
14/08/2003, 15:50
ANTENNA CONNECTIONS
If you are using an indoor or outdoor antenna, follow the instructions below that correspond to your antenna
system. If you are using a cable TV service (CATV), see page 13 for Cable TV connections.
Combination VHF/UHF Antenna (Single 75 ohm cable or 300 ohm twin-lead wire)
Connect the 75 ohm cable from the combination VHF/
UHF antenna to the Antenna Jack.
ANT.
ANT.
Antenna
Jack
75 ohm
Coaxial
Cable
If your combination VHF/UHF antenna has a 300 ohm
twin-lead wire, the use of the 300-75 ohm Matching
Transformer may be necessary.
Antenna
Jack
300-75 ohm
Matching
Transformer
Combination VHF/UHF Antenna (Separate VHF and UHF 300 ohm twin-lead wires)
300-75 ohm
Matching
Transformer
ANT.
Connect the UHF 300 ohm twin-lead wire to the
Combiner (not supplied). Connect the VHF 300 ohm
twin-lead wire to the 300-75 ohm Matching Transformer. Attach the Transformer to the Combiner, then
attach the Combiner to the Antenna Jack.
Antenna
Jack
Combiner
UHF 300 ohm
VHF 300 ohm
Separate VHF/UHF Antennas (75 ohm VHF cable and 300 ohm UHF twin-lead wires)
Connect the VHF 75 ohm cable and UHF 300 ohm
twin-lead wire to the Combiner (not supplied). Attach
the Combiner to the Antenna Jack.
ANT.
VHF 75 ohm
Antenna
Jack
Combiner
UHF 300 ohm
11
5E20101B P10-19
11
14/08/2003, 15:50
ANTENNA CONNECTIONS
(CONTINUED)
INDOOR ANTENNA (NOT SUPPLIED)
Insert a twin-lead telescopic antenna (not supplied) into the mounting hole on the back of the cabinet until it
locks into place. Attach the antenna plug to the antenna jack. Adjust the length and angle of the antenna rods to
receive the best possible picture.
ANT.
12
5E20101B P10-19
12
14/08/2003, 15:50
CABLE TV CONNECTIONS
This TV/VCR has an extended tuning range and can tune most cable channels without using a Cable TV
converter box. Some cable companies offer “premium pay channels” in which the signal is scrambled.
Descrambling these signals for normal viewing requires the use of a descrambler device which is generally provided by the cable company.
FOR SUBSCRIBERS TO BASIC CABLE TV SERVICE
For basic cable service not requiring a Converter/Descrambler box,
connect the CATV 75 ohm Coaxial Cable directly to the Antenna Jack
on the back of the TV/VCR.
ANT.
75 ohm
Coaxial Cable
Antenna
Jack
FOR SUBSCRIBERS TO SCRAMBLED CABLE TV SERVICE
If you subscribe to a cable TV service which requires the use of a Converter/Descrambler box, connect the incoming
75 ohm Coaxial Cable to the Converter/Descrambler box. Using another 75 ohm Coaxial Cable, connect the output jack
of the Converter/Descrambler box to the Antenna Jack on the TV/VCR. Follow the connections shown below. Set the
TV/VCR to the output channel of the Converter/Descrambler box (usually channel 3 or 4) and use the Converter/
Descrambler box to select channels.
Incoming
75 ohm
CATV cable
75 ohm Cable to
TV/VCR
Converter/
Descrambler
ANT.
Antenna
Jack
FOR SUBSCRIBERS TO UNSCRAMBLED BASIC CABLE TV SERVICE WITH
SCRAMBLED PREMIUM CHANNELS
If you subscribe to a cable TV service in which basic channels are unscrambled and premium channels require the
use of a Converter/Descrambler box, you may wish to use a signal splitter and an A/B Switch box (available from the
Cable company or an electronics supply store). Follow the connections shown below. With the switch in the “B”
position, you can directly tune any nonscrambled channels on your TV/VCR. With the switch in the “A” position, tune
your TV/VCR to the output of the Converter/Descrambler box (usually channel 3 or 4) and use the Converter/
Descrambler box to tune scrambled channels.
Converter/
Descrambler
Incoming
75 ohm
CATV cable
Splitter
A/B Switch
A
75 ohm cable
to TV/VCR
ANT.
B
Antenna
Jack
13
5E20101B P10-19
13
14/08/2003, 15:50
SETTING THE LANGUAGE
This TV/VCR can display the on screen language in English, Spanish or French.
On-screen language selection (step 3) will automatically appear on the screen when you press the MENU
button initially. Select the language you prefer first, then proceed with the other menu options.
1
2
Press the MENU button.
Press the SET/TR + or – button to select the
SYSTEM SETUP option, then press the
ENTER button.
MENU
Press the SET/TR + or – button to select the
LANGUAGE option, then press the ENTER
button.
ENTER
SET/TR
ENTER
SET/TR
SYSTEM SETUP
CLOCK SET
LANGUAGE/IDIOMA/LANGUE
AUTO CLOCK ON OFF
STANDARD TIME
DAYLIGHT SAVING TIME
MENU
TIMER REC SET
TV SETUP
CH SETUP
AUTO REPEAT ON OFF
SYSTEM SETUP
á
+/Ð/ENTER/MENUñ
á
+/Ð/ENTER/MENUñ
CACLO
PT SE
IO D
N
SL
EE
P
1
1 4
4
2
7
PO
WE
T
IP
E
S
A
H
R
TE
N T
U E
O ES
C R
C
R
L
E
N N
N R
A U
H T
C RE
L
A G
IT IN
IG K
D AC
TR
9
0
TR
T/
SE
C
N
O
R RN
ZE TU
E
R
A
+
C
EL
EN
M
TE
U
TE
R
SP
+
LP
H
/S
C
–
L
RA
C
K
U
–
O
V
PR
OG
LE
S
EN
6
M
1 2 3
E
S
8
T
U
P
LL
IN
A
3
C
5
R
M
+
E/S
EC
T
RE
W
Y
LA
P
ST
OP
T
REIME
C R
TIL
L
FF
Press the SET/TR + or – button to select the
desired language: English (ENGLISH), Spanish
(ESPAÑOL) or French (FRANCAIS), then press
the ENTER button.
SET/TR
L
–
H
PA
US
EJ
3
O
V
C
RE
C
4
Press the MENU button until the MENU screen
is cleared.
MENU
ENTER
LANGUAGE/IDIOMA/LANGUE
ENGLISH
ESPAÑOL
FRANCAIS
〈+/–/ENTER/MENU〉
14
5E20101B P10-19
14
14/08/2003, 15:50
AUTO CLOCK SETTING
The Auto Clock function will automatically set the built-in clock (Month, Day, Year and Time) when the TV/VCR is
connected to an Antenna or Cable system and it is turned off. As the TV/VCR searches for a receivable station in
your area and it receives a broadcast signal for Auto Clock, the Auto Clock needs several minutes to set itself.
AUTO CLOCK SETTING
1. Connect the Antenna or Cable system.
• If you use a cable box, turn it on.
2. Plug the AC Power cord to the AC outlet.
3. Make sure the TV/VCR is turned off.
• If you press the POWER button, the Auto Clock set is not effective.
4. Wait at least three minutes and press the POWER button.
5. Press the CALL button to check the clock on the screen.
6. If the clock is not set, check the Antenna condition. The Auto Clock may not function properly if the reception
condition is not good.
AUTO CLOCK ADJUSTMENT
The Auto Clock Adjustment will be performed at 12:00 PM everyday if you turn off the TV/VCR.
• If you use a cable box and you want Auto Clock adjustment to be performed, the cable box must be left on.
• The Auto Clock Adjustment is not effective when there is a difference of more than 5 minutes exists between
the built-in clock time and the actual time.
TO SET AUTO CLOCK TO OFF
When shipped from factory the AUTO CLOCK option is set to ON.
But if you do not want Auto Clock set (Adjustment):
1. Turn on the TV/VCR.
2. Press the MENU button.
3. Press the SET/TR + or – button to select the SYSTEM SETUP option, then press the ENTER button.
4. Press the SET/TR + or – button to select the AUTO CLOCK option.
5. Press the ENTER button to select OFF.
6. Press the MENU button repeatedly to return to the normal screen.
• When the AUTO CLOCK is set to OFF, the Auto Clock adjustment does not function.
• Set the clock manually (see page 17).
TO SET STANDARD TIME
In the rare event that you live within broadcast range of two stations in two different time zones, the TV/VCR may
recognize the wrong station for the Auto Clock set.
To correct the situation:
1. Press the MENU button.
2. Press the SET/TR + or – button to select the SYSTEM SETUP option, then press the ENTER button.
3. Press the SET/TR + or – button to select the STANDARD TIME option, then press the ENTER button.
4. Press the SET/TR + or – button to select your time zone, then press the ENTER button.
ATLANTIC
: GMT – 4 hours
(GMT: Greenwich Mean Time)
EASTERN
: GMT – 5 hours
CENTRAL
: GMT – 6 hours
MOUNTAIN : GMT – 7 hours
PACIFIC
: GMT – 8 hours
ALASKA
: GMT – 9 hours
HAWAII
: GMT – 10 hours
AUTO
: AUTO SET
5. Press the MENU button three times to return to the normal screen.
NOTE: To be able to select the standard time, the clock must first be set by “AUTO CLOCK” once.
15
5E20101B P10-19
15
14/08/2003, 15:50
AUTO CLOCK SETTING
(CONTINUED)
DAYLIGHT SAVING TIME SETTING
You can set the Daylight saving time automatically or manually.
1
Press the MENU button. Press the SET/TR + or
– button to select the SYSTEM SETUP option,
then press the ENTER button.
MENU
2
Press the SET/TR + or – button to select the
DAYLIGHT SAVING TIME option, then press
the ENTER button.
ENTER
SET/TR
ENTER
SET/TR
MENU
TIMER REC SET
TV SETUP
CH SETUP
AUTO REPEAT ON OFF
SYSTEM SETUP
á
SYSTEM SETUP
CLOCK SET
LANGUAGE/IDIOMA/LANGUE
AUTO CLOCK ON OFF
STANDARD TIME
DAYLIGHT SAVING TIME
+/Ð/ENTER/MENUñ
á
+/Ð/ENTER/MENUñ
CACLO
PT SE
IO D
N
SL
EE
1
1 3
P
4
2
W
PO
7
IN
3
IP
T
K
C
S
U
E
S
H
C
R
R
TE
N T
U E
O ES
C R
L
E
N N
N R
A U
H T
C RE
A
9
0
TR
T/
SE
L
A G
IT IN
IG K
D AC
TR
–
C
TE
R
U
M
TE
EN
EL
C
N
O
R RN
ZE TU
E
R
A
+
SP
+
LP
H
/S
C
–
L
RA
LE
6
EN
O
V
PR
OG
E
S
8
T
U
P
LL
A
ER
5
C
M
1 2 3
M
H
O
V
C
+
L
EC
–
R
PA
US
E/S
Y
LA
P
R
E
M C
TI RE
W
E
R
T
EC
EJ
TIL
L
P
TO
S
FF
3
Press the SET/TR + or – button to select one of the options, then press the ENTER button. Press the
MENU button until the MENU screen is cleared.
SET/TR
ENTER
MENU
DAYLIGHT SAVING TIME
for manual setting
(forward one hour)
OFF: for manual setting
(back one hour)
AUTO: for automatic setting
(read XDS in the signal)
ON:
ON
OFF
AUTO
〈+/–/ENTER/MENU〉
NOTES:
When you want to set the Daylight Saving Time manually,
on the first Sunday in April you set to “ON”, and on the last
Sunday in October you set to “OFF”.
• When shipped from factory, the DAYLIGHT SAVING TIME option is set to AUTO position.
• When the clock is not set, Daylight Saving Time setting is not available.
• When there is no Daylight Saving Time in your area, always select OFF position in step 3.
16
5E20101B P10-19
16
14/08/2003, 15:50
MANUAL CLOCK SETTING
You must set the date and time manually for Timer Recordings, ON/OFF Timer and Daylight Saving Time if
the Auto Clock process did not set them correctly.
EXAMPLE: Setting the clock to “8:30 AM”, 29th (WED) October, 2003.
1
Press the MENU button.
Press the SET/TR + or – button to select the
SYSTEM SETUP option, then press the ENTER
button.
MENU
Press the SET/TR + or – button to select the
CLOCK SET option, then press the ENTER
button.
2
ENTER
SET/TR
ENTER
SET/TR
SYSTEM SETUP
CLOCK SET
LANGUAGE/IDIOMA/LANGUE
AUTO CLOCK ON OFF
STANDARD TIME
DAYLIGHT SAVING TIME
MENU
TIMER REC SET
TV SETUP
CH SETUP
AUTO REPEAT ON OFF
SYSTEM SETUP
á
+/Ð/ENTER/MENUñ
á
+/Ð/ENTER/MENUñ
D
E N
S O
O I
L T
C AP
C
EE
SL
1
1
P
4
2
W
PO
7
IN
3
IP
T
K
C
S
U
E
S
H
C
R
A
R
TE
N T
U E
O ES
C R
L
E
N N
N R
A U
H T
C RE
L
A G
IT IN
IG K
D AC
TR
9
0
TR
T/
SE
C
TE
R
U
M
TE
EN
EL
C
N
O
R RN
ZE TU
E
R
A
+
SP
+
LP
H
/S
C
–
L
RA
LE
6
EN
–
O
V
PR
OG
E
S
8
T
U
P
LL
A
ER
5
C
M
1 2 3 4
M
H
ENTER
4
T
REIME
C R
TIL
L
FF
Set the day, year and time
as in step 3.
SET/TR
After setting the clock, date and time
starts functioning automatically.
ENTER
CLOCK SET
CLOCK SET
MONTH
DAY
YEAR
TIME
+
Y
LA
P
Press the SET/TR + or –
button to set the month,
then press the ENTER button.
SET/TR
L
–
EC
T
EC
EJ
E/S
W
ST
OP
3
O
V
C
R
PA
US
RE
MONTH
DAY
YEAR
TIME
10
1 (WED)
2003
12 : 00 AM
10
29 (WED)
2003
8 : 30 AM
8 : 30 AM WED
á +/–/ENTER/CANCEL/MENUñ
á +/–/ENTER/CANCEL/MENUñ
NOTES: • After a power failure or disconnection of the power plug, the time display will be lost. In this case, set the
present time again if the Auto Clock did not set correctly.
• To move cursor backward, press the CANCEL button.
17
5E20101B P10-19
17
14/08/2003, 15:50
TV OPERATION
1
To turn on the TV/VCR,
press the POWER button.
3
Adjust the volume level by
pressing the VOLUME + or –
button. The volume level
will be indicated on the screen by
green bars. As the volume level
increases, so do the number of bars.
If the volume decreases, the number
of green bars also decreases.
2
POWER
VOL –
Set the TV/CATV menu
option to the appropriate
position (See page 22).
TV
- VHF/UHF Channels
CATV - CABLE TV Channels
VOL +
VOLUME
32
D
E N
S O
O I
L T
C AP
C
VHF/UHF/CATV CHANNELS
1
EE
SL
TV
VHF
2-13
UHF
14-69
P
4
4
2
W
PO
7
IN
3
T
IP
U
K
C
S
LE
6
EN
E
S
H
C
R
A
R
TE
N T
U E
O ES
C R
L
E
N N
N R
A U
H T
C RE
TR
T/
SE
L
A G
IT IN
IG K
D AC
TR
9
0
–
C
TE
R
U
M
TE
EN
EL
C
N
O
R RN
ZE TU
E
R
A
+
SP
LP
+
H
/S
C
–
L
RA
E
S
8
T
U
P
LL
A
ER
5
C
M
O
V
PR
OG
M
H
+
L
–
EC
1
O
V
C
R
PA
US
T
EC
EJ
E/S
RE
W
Y
LA
P
ST
OP
T
REIME
C R
TIL
L
2
FF
CATV
VHF
2-13
STD/HRC/IRC
14-36
(A) (W)
37-59
(AA) (WW)
60-85
(AAA) (ZZZ)
86-94
(86) (94)
95-99
(A-5) (A-1)
100-125
(100) (125)
01
(5A)
4
Press the Direct Channel selection buttons to select the channel.
TV mode direct channel selection
When the TV/CATV menu option is in the TV position, all channels can be instantly selected by using two
buttons (for example, to select channel 2, press “0”, then “2”. If you press only “2”, channel selection will be delayed for a
few seconds). For channels 10 and above, press the 2 digits in order.
0
1
2
CATV mode direct channel selection
When the TV/CATV menu option is in the CATV position, channels can be selected as follows:
TO SELECT CATV CHANNELS:
1-9
Press “0” twice, then 1-9 as needed. Example, to select channel 2, press “002”.
10-12
Press “0”, then the remaining 2 digits. Example, to select channel 12, press “012”.
13-99
Press the 2 digits in order. Example, to select channel 36, press “36”.
CH 012
100-125 Press the 3 digits in order. Example, to select channel 120, press “120”.
NOTE FOR CHANNELS 1-12:
If only 1 or 2 buttons are pressed, the corresponding channel will be selected in 2 seconds.
NOTES:
• If a channel with no broadcast is selected, the sound will automatically be muted.
• If a station being viewed stops broadcasting, the TV will automatically shut itself off after 15 minutes.
18
5E20101B P10-19
18
14/08/2003, 15:50
CHANNEL + / –
MUTE
Press and release the CHANNEL + or – button. The
channel automatically stops at the next channel set
into memory.
For proper operation, before selecting channels, they
should be set into the memory. See pages 23 and 24
“To memorize channels”.
Press MUTE button to switch off the sound. The TV/
VCR’s sound will be silenced and “MUTE” will briefly
appear on the screen. The sound can be switched back
on by pressing this button again or one of the VOLUME
+ or – buttons.
MUTE
CH +
MUTE
CH 012
CH –
D
E N
S O
O I
L T
C AP
C
EE
SL
1
P
4
2
W
PO
7
IN
3
C
IP
T
K
U
E
S
H
C
R
A
R
TE
N T
U E
O ES
C R
L
E
N N
N R
A U
H T
C RE
TR
T/
SE
L
A G
IT IN
IG K
D AC
TR
9
0
–
C
TE
R
U
M
TE
EN
EL
C
N
O
R RN
ZE TU
E
R
A
+
SP
LP
+
H
/S
C
–
L
RA
LE
S
EN
6
E
S
8
T
U
P
LL
A
ER
5
C
M
O
V
PR
OG
M
H
O
V
C
+
L
EC
–
R
PA
US
T
EC
EJ
E/S
RE
W
Y
LA
P
ST
OP
TIL
L
T
REIME
C R
FF
CALL
Press the CALL button. The clock, date, channel number, real time tape counter, tape speed and VCR
operation will be indicated.
VCR operation
Press CALL button again to disappear the call display.
: Play
Current time
: Rewind
VCR operation
: Fast-forward
CALL
8:47AM THU
: Eject
: Recording
Auto Repeat
: Recording Pause
00:04:38 SP
Tape In
Tape Speed
Real Time Tape Counter
: Stop
0
0
: Zero Return (Rewind)
: Zero Return (Fast-forward)
NOTE: To listen through the headphone, insert a headphone (not supplied) with a 1/8” mini plug into PHONE jack
on the front. The sound from the TV speaker is muted.
19
5E20101B P10-19
19
14/08/2003, 15:50
TV OPERATION
(CONTINUED)
SLEEP
To set the TV/VCR to turn off after a preset amount of time, press the SLEEP button on the remote control.
The clock will count down 10 minutes for each press of the SLEEP button (120, 110, ...10, 0). After the sleep
time is programmed, the display will appear briefly every ten minutes to remind you that the sleep timer is
operating. To confirm the sleep timer setting, press the SLEEP button and the remaining time will be displayed
for a few seconds. To cancel the sleep timer, press the SLEEP button repeatedly until the display turns to 0.
SLEEP
SLEEP
120
D
E N
S O
O I
L T
C AP
C
EE
SL
1
P
4
2
W
PO
7
IN
3
T
IP
U
K
C
S
LE
6
EN
E
S
A
H
R
TE
N T
U E
O ES
C R
C
R
L
E
N N
N R
A U
H T
C RE
TR
T/
SE
L
A G
IT IN
IG K
D AC
TR
9
0
–
C
TE
R
U
M
TE
EN
EL
C
N
O
R RN
ZE TU
E
R
A
+
SP
+
LP
H
/S
C
–
L
RA
E
S
8
T
U
P
LL
A
ER
5
C
M
O
V
PR
OG
M
H
O
V
C
+
L
EC
–
R
PA
US
EJ
E/S
EC
RE
T
W
Y
LA
P
ST
OP
T
REIME
C R
TIL
L
FF
CHANNEL RETURN
CLOSED CAPTION
Press this button to switch between normal TV and
the two closed caption modes (captions and full
screen text). Closed captioning will display text on the
screen for hearing impaired viewers.
This button allows you to go back to the last channel
selected by pressing the CHANNEL RETURN button.
Press this button again to return to the last channel
you were watching.
CHANNEL
RETURN
CLOSED
CAPTION
CH 012
CAPTION CH 1
NOTES: • If using an indoor antenna or if TV reception is very poor, the Closed Caption Decoder text may not appear.
In this case, adjust the antenna for better reception or use an outdoor antenna.
• When activating the Closed Captioned Decoder, there will be a short delay before the Closed Captioned text
appears on the screen.
• Closed Captioned TV programs can be recorded and played back on a VCR with the Closed Captioned text intact.
The Closed Captioning text will disappear during Cue, Rewind and Pause modes or if the VCR tracking is not
adjusted properly.
• Closed Captioned text is only displayed in locations where it is available.
• If the Call display is on, the Closed Captioning text will not appear.
20
5E20101B P20-33
20
14/08/2003, 15:50
WHAT IS CLOSED CAPTIONING?
This television has the capability to decode and display
Closed Captioned television programs. Closed
Captioning will display text on the screen for hearing
impaired viewers or it will translate and display text in
another language.
CLOSED CAPTIONING WITH A VCR
Closed Captioned programs can be recorded and played
back on a VCR with the Closed Captioned text intact.
The Closed Captioned text will disappear during Cue
(Fast Forward Search), Review (Rewind Search) and
Pause Modes or if the VCR tracking is not adjusted
properly.
TO VIEW CLOSED CAPTIONS
Press the CLOSED CAPTION button on the remote
control to switch between normal TV and the two Closed
Caption Modes (Captions and Full Screen Text).
Captions: This Closed Caption Mode will display text
on the screen in English or another language (depending on the setting of the Closed Captions CH. 1 or 2).
Generally, Closed Captions in English are transmitted
on Captions Channel 1 and Closed Captions in other
languages are transmitted on Captions Channel 2.
Text: The Text Closed Caption Mode will usually fill the
screen with a programming schedule or other information.
After selecting a Closed Caption Mode, it will stay in
effect until it is changed, even if the channel is changed.
If the Captions signal is lost due to a commercial or a
break in the signal, the Captions will reappear when the
signal is received again.
If the channels are changed, the Captions will be delayed
approximately 10 seconds.
The Captions will appear in places on the screen where
they will least interfere with the picture, usually on the
bottom of the screen. News programs will usually show
three-line Closed Captions which scroll onto the screen.
Most other shows provide two or three lined Captions
placed near the character who is speaking so the viewer
can follow the dialogue.
Words in italics or underlined describe titles, words in
foreign languages or words requiring emphasis. Words
that are sung usually appear enclosed by musical notes.
For television programs broadcasting with Closed Captions, look in your TV guide for the Closed Captions
symbol (CC).
• When selecting Closed Captions, the captioning will be delayed approximately 10 seconds.
• If no caption signal is received, no captions will appear, but the television will remain in the Caption Mode.
• Misspellings or unusual characters may occasionally appear during Closed Captioning. This is normal with
Closed Captioning, especially with live programs. This is because during live programs, captions are also
entered live. These transmissions do not allow time for editing.
• When Captions are being displayed, on-screen displays, such as volume and mute may not be seen or may
interfere with Closed Captions.
• Some cable systems and copy protection systems may interfere with the Closed Captioned signal.
• If using an indoor antenna or if TV reception is very poor, the Closed Caption Decoder may not appear or
may appear with strange characters or misspelled words. In this case, adjust the antenna for better reception
or use an outdoor antenna.
21
5E20101B P20-33
21
14/08/2003, 15:50
TO MEMORIZE CHANNELS
This TV/VCR is equipped with a channel memory feature which allows channels to skip up or down to the
next channel set into memory, skipping over unwanted channels. Before selecting channels, they must be
programmed into the TV/VCR’s memory. In addition to normal VHF and UHF channels, this TV/VCR can
receive up to 113 Cable TV channels. To use this TV/VCR with an antenna, set the TV/CATV menu option to
the TV mode. When shipped from the factory, this menu option is in the CATV mode.
TV/CATV SELECTION
1
2
Press the MENU button.
MENU
Press the SET/TR + or – button to select the
CH SETUP mode, then press the ENTER
button.
ENTER
SET/TR
MENU
TIMER REC SET
TV SETUP
CH SETUP
AUTO REPEAT ON OFF
SYSTEM SETUP
á
+/Ð/ENTER/MENUñ
CATV CHART
The chart below is typical of many cable system channel allocations.
Number on this TV:
Corresponding CATV channel:
23
24 25 26 27 28
29 30
J
K
L
M
N
O
P
Q
41
42 43 44 45 46
47 48
EE FF GG HH
II
JJ KK LL
59
60 61 62 63 64
65 66
WW AAA BBB CCC DDD EEE FFF GGG
77
78 79 80 81 82
83 84
RRR SSS TTT UUU VVV WWW XXX YYY
95
96 97 98 99 100 101 102
A-5 A-4 A-3 A-2 A-1 100 101 102
113 114 115 116 117 118 119 120
113 114 115 116 117 118 119 120
3
Press the SET/TR + or –
button to select the TV/CATV
mode.
SET/TR
4
31
R
49
MM
67
HHH
85
ZZZ
103
103
121
121
14
A
32
S
50
NN
68
III
86
86
104
104
122
122
15
B
33
T
51
OO
69
JJJ
87
87
105
105
123
123
16
C
34
U
52
PP
70
KKK
88
88
106
106
124
124
Press the ENTER button
to select the TV or CATV
mode. The arrow indicates
the selected mode.
ENTER
17
D
35
V
53
QQ
71
LLL
89
89
107
107
125
125
18
E
36
W
54
RR
72
MMM
90
90
108
108
01
5A
5
19 20
F
G
37 38
AA BB
55 56
SS TT
73 74
NNN OOO
91 92
91 92
109 110
109 110
MENU
TV
- VHF/UHF channels
CATV - CABLE TV channels
+/Ð/ENTER/MENUñ
22
5E20101B P20-33
22
22
I
40
DD
58
VV
76
QQQ
94
94
112
112
Press the MENU button until
the MENU screen is cleared.
CH SETUP
TV CATV
AUTO CH MEMORY
ADD/DELETE
á
21
H
39
CC
57
UU
75
PPP
93
93
111
111
14/08/2003, 15:50
AUTOMATIC MEMORY TUNING
1
2
Press the MENU button.
Press the SET/TR + or – button to select the
CH SETUP mode, then press the ENTER
button.
MENU
ENTER
SET/TR
MENU
TIMER REC SET
TV SETUP
CH SETUP
AUTO REPEAT ON OFF
SYSTEM SETUP
á
+/Ð/ENTER/MENUñ
D
E N
S O
O I
L T
C AP
C
SL
EE
P
1
1 4
4
2
PO
WE
7
5
LL
A
3
C
IN
PU
8
U
EN
6
M
SK
9
0
AR
R
EL
EC
T
CH
RE ZE
TU RO
RN
C
TE
R
U
M
TE
EN
EL
C
N
A
+
SP
LP
/S
+
RA
–
H
L
C
O
V
PR
OG
SE
CO
RE UN
SE TE
T R
L
E
N N
N R
A U
H T
C RE
TR
T/
SE
L
A G
IT IN
IG K
D AC
TR
–
2 3
IP
TS
M
H
+
PA
US
E/S
RE
W
Y
LA
P
ST
OP
3
T
REIME
C R
TIL
L
FF
Press the SET/TR + or – button to select the
AUTO CH MEMORY mode, then press the
ENTER button. The TV/VCR will begin
memorizing all the channels available in your area.
Channel numbers will remain red until auto memorizing
is complete.
SET/TR
L
–
EJ
EC
T
O
V
C
RE
C
4
Press the MENU button until the MENU
screen is cleared.
MENU
ENTER
CH SETUP
TV CATV
AUTO CH MEMORY
ADD/DELETE
á
+/Ð/ENTER/MENUñ
23
5E20101B P20-33
23
14/08/2003, 15:50
TO MEMORIZE CHANNELS
(CONTINUED)
TO ADD/DELETE CHANNELS
1
2
Press the MENU button.
Press the SET/TR + or –
button to select the CH
SETUP mode, then press the
ENTER button.
Press the SET/TR + or –
button to select the ADD/
DELETE mode, then press
the ENTER button.
ENTER
SET/TR
MENU
3
ENTER
SET/TR
MENU
TIMER REC SET
TV SETUP
CH SETUP
AUTO REPEAT ON OFF
SYSTEM SETUP
á
CH SETUP
TV CATV
AUTO CH MEMORY
ADD/DELETE
+/Ð/ENTER/MENUñ
á
+/Ð/ENTER/MENUñ
D
E N
S O
O I
L T
C AP
C
SL
EE
P
1
1 6
4
2
PO
WE
7
5
LL
A
3
C
IN
PU
8
U
EN
6
M
SK
9
0
SE
AR
R
EL
EC
T
CH
RE ZE
TU RO
RN
C
TE
R
U
M
TE
EN
EL
C
N
A
+
SP
LP
/S
RA
+
–
H
L
C
O
V
PR
OG
CO
RE UN
SE TE
T R
L
E
N N
N R
A U
H T
C RE
TR
T/
SE
L
A G
IT IN
IG K
D AC
TR
–
2 3 4
IP
TS
M
H
E/S
W
Y
LA
P
Select the desired channel
to be memorized or deleted
using SET/TR + or – button,
or using the Direct Channel
Selection buttons (10 keys, 0-9),
or CHANNEL + or – button.
SET/TR
+
PA
US
RE
ST
OP
4
2 3 5
L
–
EJ
EC
T
O
V
C
RE
C
T
REIME
C R
TIL
L
FF
5
Press the ENTER button to
select the ADD or DELETE.
If you select an unmemorized
channel, the Channel indication will be
red. If you select the ADD mode, the
Channel indication changes from red to
green and the channel will be memorized.
If you select a memorized channel, the
Channel indication will be green. If you
select the DELETE mode, the Channel
indication changes from green to red
and the channel will be deleted from the
memory.
ENTER
ADD
6
Press the MENU button until
the MENU screen is cleared.
MENU
CH 003
〈0–9/+/–/ENTER/MENU〉
24
5E20101B P20-33
24
14/08/2003, 15:50
SETTING THE V-CHIP
An age limitation can be set to forbid children to watch programs according to “TV RATING” and “MOVIE
RATING” level set. To use the V-Chip function, you must register a password.
TO REGISTER PASSWORD
1
2
Press the MENU button.
Press the SET/TR + or – button to select the TV
SETUP option, then press the ENTER button.
MENU
ENTER
SET/TR
MENU
TIMER REC SET
TV SETUP
CH SETUP
AUTO REPEAT ON OFF
SYSTEM SETUP
á
+/Ð/ENTER/MENUñ
D
E N
S O
O I
L T
C AP
C
SL
EE
P
1
1
4
2
PO
WE
7
5
LL
A
3
C
IN
PU
8
U
EN
6
M
SK
9
0
SE
AR
R
EL
EC
T
CH
RE ZE
TU RO
RN
C
TE
R
U
M
TE
EN
EL
C
N
A
+
SP
/S
LP
+
RA
–
H
L
C
O
V
PR
OG
CO
RE UN
SE TE
T R
L
E
N N
N R
A U
H T
C RE
TR
T/
SE
L
A G
IT IN
IG K
D AC
TR
–
2 3
IP
TS
M
H
RE
W
Y
LA
P
ENTER
SET/TR
á
4
1
ENTER
TV SETUP
V-CHIP SET
ON/OFF TIMER
PICTURE
+
E/S
ST
OP
Press the SET/TR + or –
button to select the V-CHIP
SET then press the ENTER
button.
L
–
PA
US
EJ
EC
T
3
4 5
O
V
C
RE
C
TIL
L
T
REIME
C R
FF
Enter the password (4 digits)
using the Direct Channel
Selection buttons (0-9), then
press the ENTER button.
2
3
4
V-CHIP SET
5
1
Enter the same password
again for safety, then press
the ENTER button.
2
ENTER
V-CHIP SET
〈0–9/ENTER/CANCEL/MENU〉
〈0–9/ENTER/CANCEL/MENU〉
" "appears instead of the number.
4
CONFIRM
PASSWORD:
NEW
PASSWORD:
+/Ð/ENTER/MENUñ
3
V-CHIP SET menu appears.
If you forget the password, you cannot set the V-Chip. To avoid forgetting the password, write it down and
keep in a safe place.
25
5E20101B P20-33
25
14/08/2003, 15:50
SETTING THE V-CHIP
(CONTINUED)
TO SET THE V-CHIP
1
2
In the V-CHIP SET menu, press the SET/TR +
or – button to select the TV RATING, then
press the ENTER button.
SET/TR
Press the SET/TR + or – button to display the
desired setting, then press the ENTER button.
ENTER
ENTER
SET/TR
V-CHIP SET
V-CHIP
: OFF
TV RATING
: OFF
MOVIE RATING
: OFF
CHANGE PASSWORD
á
V-CHIP SET
V-CHIP
: OFF
TV RATING
: TVÐPG
MOVIE RATING
: OFF
CHANGE PASSWORD
+/Ð/ENTER/MENUñ
á
+/Ð/ENTER/MENUñ
D
E N
S O
O I
L T
C AP
C
SL
EE
1
P
4
2
7
PO
WE
5
LL
A
3
C
PU
TS
EL
8
EN
6
M
IP
U
9
0
T
AR
CH
RE ZE
TU RO
RN
C
TE
R
U
M
TE
EN
EL
C
N
A
+
SP
LP
/S
+
RA
–
H
L
C
O
V
PR
OG
EC
SE
CO
RE UN
SE TE
T R
L
E
N N
N R
A U
H T
C RE
TR
T/
SE
L
A G
IT IN
IG K
D AC
TR
–
1 2 3
R
IN
SK
M
H
PA
US
+
L
–
C
E/S
EJ
EC
T
RE
W
Y
LA
P
ST
OP
OFF :
TV-Y :
TV-Y7 :
TV-G :
TV-PG:
TV-14 :
TV-MA:
O
V
C
RE
T
REIME
C R
TIL
L
FF
TV RATING is not set
All children
7 years old and above
General Audience
Parental guidance
14 years old and above
17 years old and above
3
Press the SET/TR + or – button to select the
MOVIE RATING, then press the ENTER
button.
SET/TR
ENTER
V-CHIP SET
V-CHIP
: OFF
TV RATING
: TVÐPG
MOVIE RATING
: OFF
CHANGE PASSWORD
• When you select TV- Y7, TV-PG, TV-14 or TV-MA, press
the CALL button to explain the rating. Press the SET/TR
+ or – button to select the desired rating you want. Press
the ENTER button to select the setting ON or OFF.
á
NOTE: The V-Chip function is activated only on programs and tapes that have the rating signal.
26
5E20101B P20-33
26
14/08/2003, 15:50
+/Ð/ENTER/MENUñ
4
Press the SET/TR + or – button to select desired rating, then press the ENTER button.
OFF :
G
:
PG
:
PG-13 :
MOVIE RATING is not set
All ages
Parental guidance
Parental guidance
less than 13 years old
R
: Under 17 years old
Parental guidance suggested
NC-17 : 17 years old and above
X
: Adult only
ENTER
SET/TR
V-CHIP SET
V-CHIP
: OFF
TV RATING
: TVÐPG
MOVIE RATING
: PGÐ13
CHANGE PASSWORD
á
+/Ð/ENTER/MENUñ
D
E N
S O
O I
L T
C AP
C
EE
SL
1
7
P
4
2
W
PO
7
T
IP
E
S
A
H
R
TE
N T
U E
O ES
C R
C
R
L
E
N N
N R
A U
H T
C RE
L
A G
IT IN
IG K
D AC
TR
9
0
TR
T/
SE
C
N
O
R RN
ZE TU
E
R
A
+
C
EL
EN
M
TE
U
TE
R
SP
LP
+
H
/S
C
–
L
RA
C
K
U
–
O
V
PR
OG
LE
S
EN
6
E
S
8
T
U
P
LL
IN
3
A
ER
5
C
M
4 5
M
4 6
+
L
–
H
C
PA
US
E/S
EJ
EC
T
RE
W
Y
LA
P
ST
OP
5
O
V
C
RE
6
Press the SET/TR + or –
button to select
V-CHIP.
SET/TR
TIL
L
T
REIME
C R
FF
Press the ENTER button to
display ON.
7
Press the MENU button until
the MENU screen is cleared.
ENTER
MENU
V-CHIP SET
V-CHIP
: OFF
TV RATING
: TV–PG
MOVIE RATING
: PG–13
CHANGE PASSWORD
V-CHIP SET
V-CHIP
: ON
TV RATING
: TV–PG
MOVIE RATING
: PG–13
CHANGE PASSWORD
〈+/–/ENTER/MENU〉
〈+/–/ENTER/MENU〉
To use the TV after the TV is protected.
When the program applied to the V-Chip setting is received, enter the password, then press the ENTER button.
When the password is entered correctly the protection will be temporarily overridden.
27
5E20101B P20-33
27
14/08/2003, 15:50
SETTING THE V-CHIP
(CONTINUED)
TO CHANGE PASSWORD
1. Press the MENU button.
2. Press the SET/TR + or – button to select the TV SETUP, then press
the ENTER button.
MENU
TIMER REC SET
TV SETUP
CH SETUP
AUTO REPEAT ON OFF
SYSTEM SETUP
á
3. Press the SET/TR + or – button to select the V-CHIP SET, then press
the ENTER button.
TV SETUP
V-CHIP SET
ON/OFF TIMER
PICTURE
á
4. Enter the Password using the Direct Channel Selection buttons (0-9),
then press the ENTER button.
+/Ð/ENTER/MENUñ
+/Ð/ENTER/MENUñ
V-CHIP SET
PASSWORD: – – – –
á 0–9/ENTER/CANCEL/MENUñ
5. Press the SET/TR + or – button to select CHANGE PASSWORD,
then press the ENTER button.
V-CHIP SET
V-CHIP
: ON
TV RATING
: TV–PG
MOVIE RATING
: PG–13
CHANGE PASSWORD
á +/–/ENTER/MENUñ
6. Enter the new password using the Direct Channel Selection buttons
(0-9), then press the ENTER button.
V-CHIP SET
V-CHIP
: ON
TV RATING
: TV–PG
MOVIE RATING
: PG–13
CHANGE PASSWORD
NEW
PASSWORD: – – – –
〈0–9/ENTER/CANCEL/MENU〉
7. Enter the same password again to confirm, then press the ENTER
button.
V-CHIP SET
V-CHIP
: ON
TV RATING
: TV–PG
MOVIE RATING
: PG–13
CHANGE PASSWORD
CONFIRM
PASSWORD: – – – –
〈0–9/ENTER/CANCEL/MENU〉
8. Press the MENU button repeatedly to return to the normal screen.
28
5E20101B P20-33
28
14/08/2003, 15:50
TO SET THE ON TIMER
This feature allows you to have the TV/VCR automatically turn “ON” at a predetermined time. If you program the ON
TIMER once, the TV/VCR will turn on on the programmed day (daily/weekly) at the same time to the same channel.
EXAMPLE: Turning on the TV to channel 12 at 7:00 AM, MONDAY-FRIDAY.
1
Press the MENU button.
Press the SET/TR + or – button
to select the TV SETUP option,
then press the ENTER button.
SET/TR
MENU
2
Press the SET/TR + or –
button to select the ON/OFF
TIMER option, then press
the ENTER button.
ENTER
SET/TR
ENTER
MENU
TIMER REC SET
TV SETUP
CH SETUP
AUTO REPEAT ON OFF
SYSTEM SETUP
á
Press the SET/TR + or –
button to select the ON
TIMER option, then press
the ENTER button.
3
ENTER
SET/TR
ON/OFF TIMER
ON TIMER
12:00AM CH 001
SUN-SAT
CANCEL
TV SETUP
V-CHIP SET
ON/OFF TIMER
PICTURE
OFF TIMER
12:00AM
+/Ð/ENTER/MENUñ
á
+/Ð/ENTER/MENUñ
á
CANCEL
+/Ð/ENTER/CANCEL/MENUñ
D
E N
S O
O I
L T
C AP
C
EE
SL
1
1 6
P
4
2
W
PO
7
IP
T
K
C
S
U
E
S
A
H
R
TE
N T
U E
O ES
C R
C
R
L
E
N N
N R
A U
H T
C RE
TR
T/
SE
L
A G
IT IN
IG K
D AC
TR
9
0
–
C
N
O
R RN
ZE TU
E
R
A
+
C
EL
M
TE
EN
U
TE
R
SP
+
LP
H
/S
C
–
L
RA
LE
6
EN
O
V
PR
OG
E
S
8
T
U
P
LL
IN
3
A
ER
5
C
M
1 – 6
M
+
PA
US
E/S
EJ
EC
T
RE
W
Y
LA
P
ST
OP
Press the SET/TR + or –
button to set the desired hour,
then press the ENTER button.
5
T
REIME
C R
TIL
L
FF
Set the desired minute,
channel and daily or weekly
timer date as in step 4.
SET/TR
ENTER
SET/TR
L
–
H
C
4
O
V
C
RE
ENTER
Press the SET/TR + or –
button to select the SET mode,
then press the ENTER button.
Press the MENU button repeatedly to
return to normal screen.
6
SET/TR
ON/OFF TIMER
ON TIMER
7:00AM CH 001
SUN-SAT
CANCEL
OFF TIMER
12:00AM
á
ENTER
ON/OFF TIMER
ON TIMER
7:00AM CH 012
MON-FRI
CANCEL
OFF TIMER
12:00AM
CANCEL
+/Ð/ENTER/CANCEL/MENUñ
MENU
ON/OFF TIMER
ON TIMER
7:00AM CH 012
MON-FRI
SET
OFF TIMER
12:00AM
CANCEL
〈+/–/ENTER/CANCEL/MENU〉
CANCEL
〈+/–/ENTER/CANCEL/MENU〉
NOTES: • The TV/VCR will automatically turn off approximately 1 hour later after the ON TIMER turns on if no OFF TIMER
has been set. To continue watching the TV, press any button to cancel the one hour automatic shut off.
• To cancel ON TIMER, follow above steps 1-5, then press the SET/TR + or – button to select the CANCEL. Press
the MENU button repeatedly to return to the normal screen.
• After setting the ON TIMER, “ ” of the OFF TIMER will flash on and off. If you wish to set the OFF TIMER, press
the ENTER button then follow the steps 4-6 on page 30.
• If you want to correct the digits while setting, press the CANCEL button until the item you want to correct,
then press the SET/TR + or – button to correct the desired setting.
29
5E20101B P20-33
29
14/08/2003, 15:50
TO SET THE OFF TIMER
This feature allows you to have the TV/VCR turn “OFF” automatically at a predetermined time. If you program the
OFF TIMER once, the TV/VCR will automatically turn off at the same time everyday.
EXAMPLE: Turning off the TV at 11:30 PM.
1
2
Press the MENU button.
Press the SET/TR + or – button
to select the TV SETUP option,
then press the ENTER button.
SET/TR
MENU
Press the SET/TR + or –
button to select the ON/OFF
TIMER option, then press
the ENTER button.
ENTER
SET/TR
ENTER
MENU
TIMER REC SET
TV SETUP
CH SETUP
AUTO REPEAT ON OFF
SYSTEM SETUP
á
Press the SET/TR + or –
button to select the OFF
TIMER option, then press
the ENTER button.
3
SET/TR
TV SETUP
V-CHIP SET
ON/OFF TIMER
PICTURE
ENTER
ON/OFF TIMER
ON TIMER
7:00AM CH 012
MON-FRI
SET
OFF TIMER
12:00AM
+/Ð/ENTER/MENUñ
á
+/Ð/ENTER/MENUñ
CANCEL
〈+/–/ENTER/CANCEL/MENU〉
CACLO
PT SE
IO D
N
SL
EE
P
1
1 6
4
2
7
PO
WE
5
LL
A
3
C
PU
TS
EL
8
EN
6
M
IP
U
CO
RE UN
SE TE
T R
L
E
N N
N R
A U
H T
C RE
TR
T/
SE
L
A G
IT IN
IG K
D AC
TR
–
9
0
1 – 6
R
IN
EC
SK
T
SE
AR
CH
SP
LP
G
+
H
/S
C
–
L
O
PR
O
V
TE
R
U
M
TE
EN
EL
C
N
A
+
C
RE ZE
TU RO
RN
R
A
M
H
+
L
–
EC
1 – 5
O
V
C
R
4
Press the SET/TR + or –
button to set the desired hour,
then press the ENTER button.
SET/TR
FF
Press the SET/TR + or –
button to set the desired minute,
then press the ENTER button.
SET/TR
ENTER
ENTER
Press the SET/TR + or –
button to select the SET mode,
then press the MENU button
repeatedly to return to the normal
screen.
6
SET/TR
ON/OFF TIMER
ON TIMER
7:00AM CH 012
MON-FRI
SET
OFF TIMER
11:00PM
5
LL
Y
LA
P
ST
OP
T
REIME
C R
TI
/S
SE
U
PA
T
EC
EJ
RE
W
ON/OFF TIMER
ON TIMER
7:00AM CH 012
MON-FRI
SET
CANCEL
〈+/–/ENTER/CANCEL/MENU〉
OFF TIMER
11:30PM
MENU
ON/OFF TIMER
ON TIMER
7:00AM CH 012
MON-FRI
SET
OFF TIMER
11:30PM
CANCEL
〈+/–/ENTER/CANCEL/MENU〉
SET
〈+/–/ENTER/CANCEL/MENU〉
NOTES: • If a station being viewed stops broadcasting, the TV will automatically shut itself off after 15 minutes.
• To cancel OFF TIMER, follow above steps 1-5, then press the SET/TR + or – button to select the CANCEL.
Press the MENU button to return to the normal screen.
• To confirm the ON/OFF TIMER:
Press the PROGRAM button twice to indicate the programs on the screen.
30
5E20101B P20-33
30
14/08/2003, 15:50
PICTURE CONTROL ADJUSTMENTS
Picture controls are factory preset but you can adjust them individually as follows:
1
To display the picture adjustment screen, press
the MENU button. Press the SET/TR + or –
button to select the TV SETUP option, then
press the ENTER button.
MENU
Press the SET/TR + or – button to select the
PICTURE option, then press the ENTER button.
2
ENTER
SET/TR
ENTER
SET/TR
TV SETUP
V-CHIP SET
ON/OFF TIMER
PICTURE
MENU
TIMER REC SET
TV SETUP
CH SETUP
AUTO REPEAT ON OFF
SYSTEM SETUP
á
+/Ð/ENTER/MENUñ
á
+/Ð/ENTER/MENUñ
D
E N
S O
O I
L T
C AP
C
SL
EE
P
1
1
4
2
7
PO
WE
IN
T
IP
E
S
H
C
R
A
C
TE
R
U
M
TE
EN
EL
C
N
O
R RN
ZE TU
E
R
A
+
SP
LP
+
H
/S
C
–
L
RA
R
TE
N T
U E
O ES
C R
L
E
N N
N R
A U
H T
C RE
L
A G
IT IN
IG K
D AC
TR
9
0
TR
T/
SE
O
V
PR
OG
C
K
U
–
1 2
LE
S
EN
6
M
E
S
8
T
U
P
LL
A
3
C
5
R
M
+
L
–
H
T
EC
EJ
E/S
W
Y
LA
P
ST
OP
T
REIME
C R
TIL
L
FF
BRIGHTNESS
CONTRAST
Press the ENTER button until “BRIGHTNESS” appears
on the screen, then press the SET/TR + or – button
to adjust the brightness of the picture. When the
SET/TR + button is pressed, the darker portions of
the picture become lighter.
ENTER
O
V
C
EC
R
PA
US
RE
Press the ENTER button until “CONTRAST” appears
on the screen, then press the SET/TR + or – button to
adjust the contrast of the picture. Pictures look
sharpest in the daytime (bright light) by increasing the
contrast. At night (dim light), the sharpest picture is
obtained by reducing the contrast.
ENTER
SET/TR
BRIGHTNESS
0
〈+/–/ENTER/CANCEL/MENU〉
SET/TR
NOTE: The CONTRAST default
setting is set to maximum
at the factory.
CONTRAST
32
〈+/–/ENTER/CANCEL/MENU〉
31
5E20101B P20-33
31
14/08/2003, 15:50
PICTURE CONTROL ADJUSTMENTS
COLOR
TINT
Press the ENTER button until “TINT” appears on the
screen, then press the SET/TR + or – button to adjust
the tint of the picture. This determines how accurately
the colors are reproduced by the TV. Adjusting the tint
for natural facial tone is the best method of obtaining
accurate color reproduction of the entire picture.
Press the ENTER button until “COLOR” appears on
the screen, then press the SET/TR + or – button to
adjust the color intensity of the picture. The control
should be set when colors appear normal in intensity
and brilliance.
ENTER
(CONTINUED)
SET/TR
ENTER
COLOR
SET/TR
0
TINT
〈+/–/ENTER/CANCEL/MENU〉
0
〈+/–/ENTER/CANCEL/MENU〉
D
E N
S O
O I
L T
C AP
C
SL
EE
1
P
4
2
7
PO
WE
IN
C
IP
T
K
U
E
S
H
R
TE
N T
U E
O ES
C R
C
R
L
E
N N
N R
A U
H T
C RE
A
9
0
TR
T/
SE
L
A G
IT IN
IG K
D AC
TR
–
C
TE
R
U
M
TE
EN
EL
C
N
O
R RN
ZE TU
E
R
A
+
SP
LP
+
H
/S
C
–
L
RA
LE
S
EN
6
M
O
V
PR
OG
E
S
8
T
U
P
LL
A
3
C
5
R
M
+
L
–
H
O
V
C
EC
R
PA
US
T
EC
EJ
E/S
RE
W
Y
LA
P
ST
OP
T
REIME
C R
TIL
L
FF
SHARPNESS
CANCEL
Press the ENTER button until “SHARPNESS” appears
on the screen, then press the SET/TR + or – button
to adjust the sharpness of the picture.
Pressing the CANCEL button while making picture
adjustments will return all adjustments to the factory
preset levels.
CANCEL
ENTER
SET/TR
SHARPNESS
0
〈+/–/ENTER/CANCEL/MENU〉
NOTE: The On-screen display will disappear 6 seconds after finishing an adjustment or by pressing the MENU
button three times. The settings can only be adjusted when they are displayed on the TV screen.
32
5E20101B P20-33
32
14/08/2003, 15:50
LOADING AND UNLOADING A VIDEO CASSETTE
Use only video cassette tapes marked
.
LOADING
Push the center of the tape until it is automatically retracted into the TV/VCR.
AUTOMATIC POWER ON AND PLAY
When loading a cassette tape without the erase prevention tab intact, the TV/VCR will turn on automatically
and playback will start immediately.
Insert the cassette with its labeled side facing you.
An inverted video cassette cannot be inserted.
2
1
UNLOADING
1
To unload a video cassette, press the EJECT
button on the remote control, or press the
STOP/EJECT button on the TV/VCR twice.
The first press will stop the tape in any mode. The
second press will eject the tape.
2
Pull the cassette out.
STOP/EJECT
EJECT
OR
AUTOMATIC EJECT
If the TV/VCR automatically rewinds the tape to the
beginning (AUTO REWIND FEATURE), the tape will
be ejected automatically (See NOTE on page 40).
NOTES:
• Always eject the tape when not in use.
• The cassette tape can be ejected even if the POWER is “OFF”.
33
5E20101B P20-33
33
14/08/2003, 15:50
LOADING AND UNLOADING A VIDEO CASSETTE (CONTINUED)
TO PREVENT ACCIDENTAL ERASURE
After recording, break off the erase prevention tab if
you do not wish to record over the tape.
Screwdriver
Erase prevention tab
TO RECORD AGAIN
Cover the hole with adhesive tape.
Be careful the tape does not extend past the edges of
the video cassette housing.
Adhesive tape
TAPE SPEED AND MAXIMUM PLAYBACK/RECORDING TIME
VIDEO CASSETTE TAPE
TAPE SPEED
T-160
T-120
T-90
T-60
T-30
SP (Standard Play)
2-2/3 hours
2 hours
1-1/2 hours
1 hour
30 minutes
SLP (Super Long Play)
8 hours
6 hours
4-1/2 hours
3 hours
1-1/2 hours
34
5E20101B P34-43
34
14/08/2003, 15:50
PLAYBACK
To play a prerecorded tape.
TO START PLAYBACK
1
2
To turn on the TV/VCR, press the POWER button.
Load a prerecorded tape (When loading a
cassette tape without the erase prevention tab,
playback will start automatically).
POWER
D
E N
S O
O I
L T
C AP
C
EE
SL
1
P
4
2
W
PO
7
IN
3
LE
T
IP
U
K
C
S
EN
6
E
S
8
T
U
P
LL
A
ER
5
C
M
E
S
R
A
H
R
TE
N T
U E
O ES
C R
L
E
N N
N R
A U
H T
C RE
TR
T/
SE
L
A G
IT IN
IG K
D AC
TR
9
0
–
C
3
SP
LP
M
A
R
G
+
–
H
/S
C
L
O
PR
O
V
TE
R
U
M
TE
EN
EL
C
N
O
R RN
ZE TU
E
R
A
+
C
1
H
O
V
C
+
L
–
EC
R
W
Y
LA
P
R
E
M C
TI RE
E
LL
TI
/S
SE
U
PA
R
T
EC
EJ
S
TO
P
FF
TO STOP PLAYBACK
3
Press the PLAY button to begin playback.
“ ” will appear on the screen.
PLAY
Press the STOP button once. The tape will stop, but
remain fully loaded and ready to play. “ ” will
appear on the screen.
STOP
NOTE: This TV/VCR selects the playback tape speed SP or SLP automatically.
35
5E20101B P34-43
35
14/08/2003, 15:50
PLAYBACK
(CONTINUED)
TO REWIND OR FORWARD THE TAPE RAPIDLY
Press the FF (Fast Forward) button in the Stop mode.
“ ” will appear on the screen.
Press the REW (Rewind) button in the Stop mode.
“ ” will appear on the screen.
REW
FF
FORWARD/REVERSE PICTURE SEARCH
If you want to see the tape during REW or FF mode, press and hold the REW or FF button. The backward
or forward visual search picture will be seen on the screen. Release to return to the REW or FF mode.
D
E N
S O
O I
L T
C AP
C
SL
EE
1
P
4
2
PO
WE
7
5
IN
3
LL
A
C
PU
8
6
U
EN
M
T
CH
R
SP
LP
/S
O
V
+
L
–
T
REIME
C R
W
Y
LA
P
ST
OP
AR
R
EC
TE
U
M
TE
EN
+
H
H
PA
US
RE
T
SE
EL
RE ZE
TU RO
RN
EL
C
N
A
C
+
C
C
C
EC
IP
TS
M
RE
EJ
CO
RE UN
SE TE
T R
L
E
N N
N R
A U
H T
C RE
TR
T/
SE
L
A G
IT IN
IG K
D AC
TR
9
0
–
RA
–
L
O
V
PR
OG
SK
E/S
TIL
L
FF
DIGITAL TRACKING CONTROLS
When a tape is played, the Digital Auto Tracking system automatically adjusts the tracking to obtain the best
possible picture. If noise bars appear during playback, adjust the tracking manually as follows:
• Press the SET/TR + or – button to obtain the best possible picture.
“MANUAL TRACK” will appear for 4 seconds on the screen. To resume automatic tracking, press the DIGITAL
TRACKING button. “DIGITAL TRACK” will appear for 4 seconds on the screen.
SET/TR
DIGITAL
TRACKING
MANUAL TRACK
Ð
+
DIGITAL TRACK
36
5E20101B P34-43
36
14/08/2003, 15:50
SPECIAL PLAYBACK
TO VISUALLY SEARCH FOR DESIRED POINTS
When either the FF or REW button is pressed in the PLAYBACK mode, the speed search picture will appear. When
pressed twice, the search picture will increase speed. Speed search time depends upon the speed used (SP or SLP)
during recording. See chart below.
To rewind or fast forward a tape, press the STOP button, and then press the REW or FF button.
To visually search backward, press the REW button
once or twice in the PLAYBACK mode.
To visually search forward, press the FF button
once or twice in the PLAYBACK mode.
REW
FF
Press the PLAY button to resume normal viewing
speed.
Press the PLAY button to resume normal viewing
speed.
SPEED SEARCH TIMES
D
E N
S O
O I
L T
C AP
C
PICTURE SEARCH SPEED
SL
EE
P
1
TAPE SPEED
9X
15 X
2
SLP (Super Long
Play)
5
5X
4
SP (Standard Play)
3X
LL
A
EL
8
6
EN
EC
SK
IP
U
CO
RE UN
SE TE
T R
L
E
N N
N R
A U
H T
C RE
TR
T/
SE
L
A G
IT IN
IG K
D AC
TR
9
0
–
T
SE
AR
CH
RE ZE
TU RO
RN
C
TE
R
U
M
TE
EN
EL
C
N
A
+
SP
LP
+
–
H
/S
C
L
RA
R
PU
TS
M
O
V
PR
OG
M
H
O
V
C
+
L
EC
–
R
PA
US
T
EC
EJ
E/S
RE
W
Y
LA
P
ST
OP
TO WATCH STILL PICTURE
PO
WE
IN
3
C
PRESS
TWICE
7
PRESS
ONCE
T
REIME
C R
TIL
L
FF
SKIP SEARCH
Press the PAUSE/STILL button in the
PLAYBACK mode.
PAUSE/STILL
Press the SKIP SEARCH button in the PLAY mode. The TV/VCR will
search forward through approximately 30 seconds of the tape (e.g.
unwanted commercial time) for each press of the SKIP SEARCH
button (maximum six presses) and then resume normal playback.
For example : 1 press: 30 seconds of tape
2 press: 60 seconds of tape
3 press: 90 seconds of tape
SKIP SEARCH
Press the PLAY button or PAUSE/
STILL button to resume normal
playback.
NOTES: • Best results during speed search and still playback can be obtained with video cassettes recorded in the
“SLP” mode.
• The audio output is muted during Speed Search and Still.
• A few noise bars will appear on the TV screen during Speed Search and Still.
• To prevent damage to the tape, Still and Speed Search mode is automatically changed to the Playback
mode after 5 minutes.
37
5E20101B P34-43
37
14/08/2003, 15:50
SPECIAL PLAYBACK
(CONTINUED)
TO WATCH A TAPE REPEATEDLY
1
2
Press the MENU button.
Press the SET/TR + or – button to select the
AUTO REPEAT option.
SET/TR
MENU
MENU
TIMER REC SET
TV SETUP
CH SETUP
AUTO REPEAT ON OFF
SYSTEM SETUP
á
+/Ð/ENTER/MENUñ
D
E N
S O
O I
L T
C AP
C
EE
SL
1
1 4
P
4
2
W
PO
7
LL
A
3
IN
PU
8
6
U
EN
9
0
L
E
N N
N R
A U
H T
C RE
TR
T/
SE
L
A G
IT IN
IG K
D AC
TR
–
AR
TS
EL
EC
T
CH
TE
R
U
M
TE
EN
EL
C
N
A
+
SP
LP
/S
RA
+
–
H
L
C
O
V
PR
OG
SE
RE ZE
TU RO
RN
C
2
CO
RE UN
SE TE
T R
IP
ER
5
C
M
SK
M
H
+
L
–
EC
3
EJ
E/S
EC
T
W
Y
LA
P
ST
OP
3
O
V
C
R
PA
US
RE
T
REIME
C R
TIL
L
FF
Press the ENTER button to select the ON
position.
ENTER
4
Press the MENU button. If you press the PLAY
button, the tape will play over and over until the
repeat mode is canceled.
MENU
MENU
TIMER REC SET
TV SETUP
CH SETUP
AUTO REPEAT ON OFF
SYSTEM SETUP
á
+/Ð/ENTER/MENUñ
NOTE: To cancel repeat mode, follow above steps 1 and 2, then press the ENTER button to select the OFF position.
Press the MENU button to return to the TV.
The repeat function is canceled automatically when the unit is switched off or the tape is ejected.
38
5E20101B P34-43
38
14/08/2003, 15:50
RECORDING A TV PROGRAM
RECORDING AND VIEWING THE SAME TV PROGRAM
1
2
To turn on the TV/VCR, press the POWER
button.
Load a cassette tape with the erase prevention
tab intact.
POWER
CACLO
PT SE
IO D
N
EE
SL
1
P
4
2
W
PO
7
ER
5
3
LL
A
C
IN
PU
TS
8
EL
6
U
EN
M
EC
SK
IP
L
E
N N
N R
A U
H T
C RE
TR
T/
SE
L
A G
IT IN
IG K
D AC
TR
9
0
–
CO
RE UN
SE TE
T R
T
SE
AR
CH
1
+
G
LP
/S
SP
H
C
–
O
PR
L
O
V
TE
U
M
R
TE
EN
EL
C
N
A
C
+
RE ZE
TU RO
RN
R
A
M
H
O
V
C
+
L
EC
–
R
U
PA
3
SE
/S
T
Y
LA
P
3
LL
EC
T
REIME
C R
W
ST
OP
TI
EJ
RE
FF
Press the SP/SLP button to select the desired
tape speed SP or SLP. The counter and SP or
SLP will appear on the screen about 4 seconds.
4
Set the TV/CATV option to the appropriate
position (See page 22).
SP/SLP
TV
- VHF/UHF channels
CATV - CABLE TV channels
00:00:00 SP
NOTES:
• If power is switched off during recording, the TV set goes off and the VCR continues to record. Press the
STOP button to halt the recording and turn off the VCR.
• The TV/VCR Channel cannot be changed during recording.
39
5E20101B P34-43
39
14/08/2003, 15:50
RECORDING A TV PROGRAM
5
(CONTINUED)
6
Press the Direct Channel Selection buttons or
CHANNEL + or – button to select the channel to
be recorded (Example: Channel 12).
Press both the REC buttons at the same time.
“ ● ” and the channel number will appear on the
screen and the REC indicator will light.
CH +
0
1
2
REC
OR
CH –
CH 012
CH 012
REC
D
E N
S O
O I
L T
C AP
C
EE
SL
1
P
4
2
W
PO
7
3
LL
A
PU
TS
EL
8
EN
6
M
IP
U
CO
RE UN
SE TE
T R
L
E
N N
N R
A U
H T
C RE
TR
T/
SE
L
A G
IT IN
IG K
D AC
TR
9
0
–
EC
T
SE
AR
CH
RE ZE
TU RO
RN
C
N
A
+
SP
LP
+
H
/S
C
5
M
A
R
G
O
PR
–
L
O
V
TE
R
U
M
TE
EN
EL
C
6
ER
5
C
IN
SK
+
C
L
–
H
O
V
C
RE
SE
U
PA
LL
W
R
E
M C
TI RE
E
T
R
EC
TI
/S
EJ
Y
LA
P
S
5
TO
P
FF
TO STOP RECORDING
TO STOP RECORDING TEMPORARILY
Press the PAUSE/STILL button to avoid recording unwanted material.
“ ” and the channel number will appear on the screen and the REC
indicator will blink on and off. Press the PAUSE/STILL button or both
the REC buttons to continue the recording.
Press the STOP button to stop
recording.
“ ■ ” will appear on the screen.
STOP
PAUSE/STILL
CH 012
or
REC
NOTE:
The PAUSE mode will be changed to STOP mode after five minutes to
prevent damage to the tape.
NOTES: • AUTO REWIND FEATURE
This TV/VCR will automatically rewind the video cassette when the tape has ended (except during OTR and
Timer Record). It will also eject the video cassette.
• If the erase prevention tab is removed, the tape will eject when both the REC buttons are pressed for recording.
40
5E20101B P34-43
40
14/08/2003, 15:50
ONE-TOUCH TIMER RECORDING (OTR)
The One-touch Timer Recording feature provides a simple and convenient way to make a timed recording.
EXAMPLE: One-touch Timer Recording for 30 minutes.
1
2
Press the POWER button
to turn on the TV/VCR.
3
Press the SP/SLP button to
select the desired tape
speed (SP or SLP).
SP or SLP will appear on the screen.
Load a video cassette
with the erase prevention
tab intact.
POWER
SP/SLP
00:00:00 SP
CACLO
PT SE
IO D
N
SL
EE
P
1
5
4
2
PO
WE
7
5
3
LL
A
C
IN
PU
8
6
U
EN
M
IP
CO
RE UN
SE TE
T R
L
E
N N
N R
A U
H T
C RE
TR
T/
SE
L
A G
IT IN
IG K
D AC
TR
9
0
–
SE
AR
R
EL
EC
T
1
CH
RE ZE
TU RO
RN
EL
C
N
A
C
+
SP
LP
M
A
R
G
+
–
H
/S
C
L
O
PR
O
V
TE
U
M
R
TE
EN
6
SK
TS
H
O
V
C
L
+
EC
–
R
3
/S
SE
U
PA
LL
TI
Y
LA
P
R
E
M C
TI RE
W
E
R
T
EC
EJ
P
TO
S
5
FF
4
Set the TV/CATV option
to the appropriate setting
(See page 22).
5
0
TV
- VHF/UHF channels
CATV - CABLE TV channels
Press the Direct Channel
Press both the REC buttons
Selection buttons or CHANNEL
at the same time to begin
+ or – button to select the
recording. Press the buttons
channel to be recorded
again to stop recording after 30
(Example: Channel 12).
minutes. Each additional press of
the REC buttons will increase
OR
1
2
recording time as shown below, up
to a maximum of 6 hours. “OTR” will
CH –
appear on the screen.
6
CH +
REC
OTR 0 : 30
CH 012
CH 012
NOTES: • Press both the REC buttons at the same time to increase the time needed for recording (See the chart below).
Press
once
Recording time NORMAL REC
twice
3 times
4 times
5 times
6 times
7 times
8 times
9 times
10 times
0:30
1:00
1:30
2:00
3:00
4:00
5:00
6:00
NORMAL REC
• To cancel OTR, press the STOP button.
• The TV/VCR channel cannot be changed during recording.
5E20101B P34-43
41
41
14/08/2003, 15:50
TIMER RECORDING
Timer recording can be programmed on-screen with the remote control. The built-in timer allows automatic
unattended recording of up to 8 programs within 1 month.
EXAMPLE: Program a timer recording for 23rd day, channel 007 (CATV), 7:00 - 9:30 PM (Tape speed : SLP).
• Load a video cassette with the erase prevention tab intact. The TV/VCR will automatically turn on.
• Set the TV/CATV selection to the appropriate position (See page 22).
1
2
Press the MENU button.
Check the TIMER REC SET option is selected,
then press the ENTER button.
MENU
ENTER
MENU
TIMER REC SET
TV SETUP
CH SETUP
AUTO REPEAT ON OFF
SYSTEM SETUP
á
+/Ð/ENTER/MENUñ
D
E N
S O
O I
L T
C AP
C
EE
SL
1
1
P
4
2
W
PO
7
IN
3
LE
T
IP
U
K
C
S
EN
6
E
S
8
T
U
P
LL
A
ER
5
C
M
E
S
A
H
R
TE
N T
U E
O ES
C R
C
R
L
E
N N
N R
A U
H T
C RE
TR
T/
SE
L
A G
IT IN
IG K
D AC
TR
9
0
–
SP
LP
G
+
–
H
/S
C
L
O
PR
O
V
TE
R
U
M
TE
EN
EL
C
N
O
R RN
ZE TU
E
R
A
+
C
3 4
R
A
M
H
O
V
C
C
2 3 4
+
L
–
RE
U
PA
SE
T
W
Y
LA
P
ST
OP
3
T
REIME
C R
FF
Press the SET/TR + or – button to select the
program position, then press the ENTER
button.
SET/TR
ENTER
4
Press the SET/TR + or – button to select the
date, then press the ENTER button.
SET/TR
--------------------------------á
NOTES:
LL
RE
TI
EC
/S
EJ
-:--:--:--:--:--:--:--:--
-:--:--:--:--:--:--:--:--
-----------------
ENTER
-
TIMER REC SET
DATE
START
END
CH
SPEED
+/Ð/ENTER/CANCEL/MENU ñ
23 (THU)
8 : 30 AM
-- : -012
SP
á +/Ð/ENTER/CANCEL/MENU ñ
• If programming is performed without a tape in the TV/VCR, or with a tape without an erase prevention
tab, the Timer Recording is not possible. If a tape without an erase prevention tab is in the TV/VCR the
tape will be ejected.
• To record from the external equipment press the SET/TR + or – button repeatedly until “LINE (from AUDIO/
VIDEO IN jacks on the front)” appears when setting the channel in step 5.
42
5E20101B P34-43
42
14/08/2003, 15:50
5
Set the start time, end time, channel and tape speed as in step 4.
SET/TR
ENTER
23 TH
TIMER REC SET
DATE
START
END
CH
SPEED
-----------------------------
23 (THU)
7 : 00 PM
9 : 30 PM
007
SLP
〈+/–/ENTER/CANCEL/MENU〉
á
7:00PM 9:30PM 007 SLP
-:--:--:--:--:--:--:--
-:--:--:--:--:--:--:--
---------------
-
+/Ð/ENTER/CANCEL/MENU ñ
D
E N
S O
O I
L T
C AP
C
SL
EE
1
P
4
2
PO
WE
7
5
3
LL
A
C
IN
PU
8
AR
T
CH
TE
U
M
LP
/S
SP
W
L
E
N N
N R
A U
H T
C RE
R
TE
EN
RE
SE
R
EC
RE ZE
TU RO
RN
EL
C
N
A
C
+
CH
+
VO
L
–
PA
US
Y
LA
P
ST
OP
6
CH
–
CO
RE UN
SE TE
T R
IP
EL
M
C
T
9
0
TR
T/
SE
VO
L
RA
RE
EC
L
A G
IT IN
IG K
D AC
TR
–
PR
OG
EJ
6
U
EN
M
5
SK
TS
T
REIME
C R
+
E/S
TIL
L
7
FF
To set the timer for another program, press the
SET/TR + or – button until the number of the
second program blinks, then press the ENTER
button. Repeat steps 4 to 5 to set the second
program.
7
Press both the TIMER REC buttons at the same
time. The TIMER REC indicator will light. The
Timer is programed, when the programed time is
reached, the recording is automatically started.
TIMER
REC
4
5
TIMER REC
To cancel timer recording, press both the buttons again
and TIMER REC indicator will go off.
NOTES: • The VCR section cannot be used while the TIMER REC indicator is lit. If you want to use the VCR operation,
press both the TIMER REC buttons at the same time to deactivate the timer.
• After a power failure or disconnection of the power plug, all programed recording setting and time display will be lost
upon resumption of power. In this case, reset the clock (see pages 15-17) and reprogram any timer recordings.
• If you want to correct the digits while setting, press the CANCEL button until the item you want to correct, then
press the SET/TR + or – button to correct the desired setting.
43
5E20101B P34-43
43
14/08/2003, 15:50
OTHER FUNCTIONS FOR THE TIMER RECORDING
TO CONFIRM THE SETTINGS
TO SET DAILY/WEEKLY TIMER
When setting the date in the step 4 on page 42, press
the SET/TR – button repeatedly when the current day
is displayed.
The setting changes as follows:
Press the PROGRAM button once. The TV screen
displays the timer program list.
Press the PROGRAM button again. The TV screen
displays the ON/OFF timer setting.
Example
The current day (Friday)
One month later
minus one day
SUN-SAT
(once)
(Sunday to Saturday)
MON-SAT
(Monday to Saturday)
MON-FRI
(Monday to Friday)
PROGRAM
----------------------------á
WKL-WED
(Weekly Wednesday)
WKL-THU
(twice)
7:00PM 9:30PM 007 SLP
23 TH
-:--:--:--:--:--:--:--
-:--:--:--:--:--:--:--
---------------
ON/OFF TIMER
ON TIMER
7:00AM CH012
MON-FRI
SET
-
OFF TIMER
11:30PM
+/Ð/ENTER/CANCEL/MENU ñ
SET
〈+/–/ENTER/CANCEL/MENU〉
(Weekly Thursday)
Press the PROGRAM button 3 times. The screen
returns to the normal screen.
CACLO
PT SE
IO D
N
EE
SL
1
P
4
2
W
PO
7
3
PU
LL
A
ER
5
C
IN
TS
8
EL
EN
6
M
EC
SK
U
IP
L
E
N N
N R
A U
H T
C RE
TR
T/
SE
L
A G
IT IN
IG K
D AC
TR
9
0
–
CO
RE UN
SE TE
T R
T
SE
AR
CH
SP
LP
+
H
/S
C
M
A
R
G
O
PR
–
L
O
V
TE
R
U
M
TE
EN
EL
C
N
A
+
C
RE ZE
TU RO
RN
+
C
L
–
H
O
V
C
RE
SE
U
PA
RE
W
T
Y
LA
P
ST
OP
T
REIME
C R
LL
EC
TI
/S
EJ
FF
TO CANCEL A PROGRAM
IF THE PROGRAM OVERLAPS ANOTHER
Press the SET/TR + or – button to select the TIMER
REC SET option in the MENU, then press the
ENTER button. Press the SET/TR + or – button to
select the unnecessary program, and press the
CANCEL button to cancel the program.
NOTE: Do not overlap programs as portions of the
conflicting programs will be lost. The first
recording time has priority over the next
recording time as shown in the diagram.
8 : 00
CANCEL
9 : 00
10 : 00
11 : 00
Program 1
Program 2
--------------------------------á
-:--:--:--:--:--:--:--:--
-:--:--:--:--:--:--:--:--
-----------------
-
Deleted Parts
Program 3
Non Recorded Portion Parts
Recording
Control Settings
Prog.1
Prog.2
Prog.3
+/Ð/ENTER/CANCEL/MENU ñ
NOTES: • The everyday/every week recording can be made continuously until the recording is canceled or the tape
reaches the end.
• During timer recording, the automatic rewinding mechanism does not function.
• You can correct or cancel the programmed setting in program confirm mode.
44
5E20101B P44-BACK
44
14/08/2003, 15:50
USING THE REAL TIME TAPE COUNTER
The On-Screen Real Time Tape Counter shows the tape running time in Hours, Minutes and Seconds.
You can easily determine how long the tape has been running or how much time is left on the tape.
TO VIEW THE COUNTER DISPLAY
1
2
Press the CALL button.
Press the COUNTER RESET button to set the
counter to “00:00:00”.
CALL
COUNTER
RESET
8:40AM THU
8:40AM THU
CH 012
00:30:50 SP
CH 012
00:00:00 SP
CACLO
PT SE
IO D
N
EE
SL
1
1 4
P
4
2
W
PO
7
3
LL
A
PU
TS
EL
8
EN
6
M
IP
U
CO
RE UN
SE TE
T R
L
E
N N
N R
A U
H T
C RE
TR
T/
SE
L
A G
IT IN
IG K
D AC
TR
9
0
–
EC
T
SE
AR
CH
RE ZE
TU RO
RN
C
SP
LP
+
H
/S
C
M
A
R
G
O
PR
–
L
O
V
TE
R
U
M
TE
EN
EL
C
N
A
+
3
ER
5
C
IN
SK
+
C
L
–
H
O
V
C
RE
U
PA
RE
W
Y
LA
P
ST
OP
T
REIME
C R
LL
T
TI
/S
EC
3
2
SE
EJ
FF
Begin Playback or Recording to start the tape,
the counter will display the elapsed time.
4
When you wish to make the counter disappear,
press the CALL button once again.
REC
PLAY
CALL
OR
NOTES:
• If you rewind the tape from “00:00:00”, a minus sign (“–”) will be displayed in front of the time.
• When you load a tape, the counter will reset to “00:00:00”.
• The counter does not function on nonrecorded (blank) sections of the tape. When you rewind,
fast forward or play tapes through blank sections, the counter stops.
45
5E20101B P44-BACK
45
14/08/2003, 15:50
USING ZERO RETURN
The zero return function provides a convenient method of rapidly returning to the starting point of recording
or playback. The starting point can be indexed for any location on the tape by pressing the COUNTER
RESET button and ZERO RETURN button.
1
2
Press the CALL button.
Before playback or recording, press the
COUNTER RESET button to set the counter
to “00:00:00”.
COUNTER
RESET
CALL
8:40AM THU
8:40AM THU
CH 012
00:30:50 SP
CH 012
00:00:00 SP
CACLO
PT SE
IO D
N
1
EE
SL
1
P
4
2
W
PO
7
3
LL
A
PU
TS
EL
8
EN
6
M
IP
U
TR
T/
CO
RE UN
SE TE
T R
L
E
N N
N R
A U
H T
C RE
SE
L
A G
IT IN
IG K
D AC
TR
9
0
–
EC
T
SE
AR
CH
RE ZE
TU RO
RN
2
SP
LP
+
H
/S
C
M
A
R
G
O
PR
–
L
O
V
TE
R
U
M
TE
EN
EL
C
N
A
+
C
3
ER
5
C
IN
SK
5
+
C
L
–
H
O
V
C
RE
SE
U
PA
T
RE
T
REIME
C R
W
Y
LA
P
ST
OP
3
Begin playback or recording.
4
LL
EC
TI
/S
EJ
FF
4
Press the STOP button.
STOP
Press the ZERO RETURN
button. The tape will rewind
and automatically stop at
the “00:00:00” position.
ZERO
RETURN
REC
PLAY
5
OR
9:00AM THU
9:00AM THU
CH 012
00:20:00 SP
00:00:00 SP
46
5E20101B P44-BACK
46
CH 012
14/08/2003, 15:50
DUPLICATING A VIDEO TAPE
If you connect the TV/VCR to another VCR or Camcorder, you can duplicate a previously recorded tape. Make
all connections before turning on the power.
1
Insert a blank cassette with the erase prevention tab intact into the TV/VCR.
Insert a previously recorded cassette into the
playback VCR or Camcorder.
2
Press the INPUT SELECT button to select
AUDIO/VIDEO input position. “LINE” will
appear on the screen.
INPUT SELECT
LINE
CONNECTION TO ANOTHER VCR
CONNECTION TO CAMCORDER
Recording TV/VCR
For duplicating a previously recorded tape from a camcorder,
follow the camcorder manufacturer’s instructions. A typical
camcorder dubbing hookup is shown below.
Recording TV/VCR
Playback Camcorder
Playback VCR
To AV jack
To VIDEO To AUDIO
OUT OUT
To Video In
To Audio In
To Video/Audio In
Audio/Video cable (not supplied)
Audio/Video cable (not supplied)
3
Press both the REC buttons
at the same time on the
remote control of the TV/VCR,
then press the PAUSE/STILL
button.
REC
4
Press the PLAY Button on the
playback VCR, then press the
PAUSE/STILL button.
PAUSE/
STILL
PAUSE/STILL
5
Release the recording
pause and the playback
simultaneously to begin the
duplicating process.
PAUSE/STILL
PAUSE/
STILL
PLAY
NOTES:
• It is recommended that the tape speed be set to the SP mode on the TV/VCR for best result.
• Unauthorized recording of copyrighted television programs, films, video cassettes and other materials
may infringe the rights of copyright owners and be contrary to copyright laws.
47
5E20101B P44-BACK
47
14/08/2003, 15:50
PROBLEM AND TROUBLESHOOTING GUIDE
Check the following chart before requesting service.
SYMPTOM
CAUSE
POSSIBLE SOLUTION
PAGE
POWER
No power.
Although the power is on,
the TV/VCR does not
operate.
The AC power cord is not connected.
Connect the AC power cord to the
AC outlet.
7
Cassette is not inserted.
Insert a video cassette.
33
TIMER REC buttons is depressed.
Press the TIMER REC buttons.
43
TV BROADCAST RECEPTION
Poor or no picture.
Try another channel.
Picture control is not adjusted.
Check picture control adjustments.
Possible local interference.
Check for source of reception
disturbance.
Antenna (CATV) connector is not
connected or possible local
interference.
Check CATV connection or VHF/
UHF antenna, reposition or rotate
antenna.
TV station experiencing problems.
Try another channel.
Picture control is not adjusted.
Check picture control adjustments.
Possible local interference.
Check for source of reception
disturbance.
Antenna (CATV) connector is not
connected or possible local
interference.
Check CATV connection or VHF/
UHF antenna, reposition or rotate
antenna.
TV station experiencing problems.
Try another channel.
Antenna (CATV) connector is not
connected or possible local
interference.
Check CATV connection or VHF/
UHF antenna, reposition or rotate
antenna.
Cable TV channel is scrambled.
Try another channel.
18
CATV connector is not connected.
Check all CATV connections.
13
TV/CATV Mode menu option is set to
the TV mode.
Set the TV/CATV Menu option to
the CATV mode.
22
Cable TV service interrupted.
Contact your Cable TV company.
13
TV/CATV Mode menu option is not
set to the appropriate mode.
Make sure TV/CATV menu option is
in the appropriate mode.
22
UHF antenna is not connected.
Check UHF antenna.
11
TV station experiencing problems.
Try another channel.
18
Antenna (CATV) connector is not
connected or possible local
interference.
Check CATV connection or VHF/
UHF antenna, reposition or rotate
antenna.
Possible local interference.
Check for source of reception
disturbance.
50
MUTE button is depressed.
Check that MUTE button has not
been pressed.
19
Poor or no color.
Picture wobbles or drifts.
No CATV reception.
No reception above
channel 13.
Poor or no sound.
48
5E20101B P44-BACK
18
TV station experiencing problems.
48
14/08/2003, 15:50
31, 32
50
11, 13
18
31, 32
50
11, 13
18
11, 13
11, 13
SYMPTOM
TV shuts off.
Closed caption is not
activated.
CAUSE
POSSIBLE SOLUTION
PAGE
TV station stopped broadcasting.
Tune new channel.
18
Sleep timer is set.
Set Sleep Timer to “0”.
20
OFF timer is set.
Set OFF TIMER to “CANCEL”.
TV station experiencing problems or
program tuned is not closed captions.
Try another channel.
18, 19
TV signal is weak.
Check CATV connection of VHF/
UHF antenna, reposition or rotate
antenna.
11, 13
30
The CLOSED CAPTION button is not
depressed.
Press the CLOSED CAPTION button
20, 21
to turn on the closed caption.
The video cassette's erase prevention
tab is broken off.
Place a piece of vinyl tape over the
hole.
34
The time is not set correctly.
Reset the present time.
17
The recording start/end time is not
set correctly.
Reset the start/end time.
The TIMER REC buttons has not
been pressed (The TIMER REC
indicator is not lit).
Press the TIMER REC buttons (The
TIMER REC indicator is lit).
43
Tape is old or worn.
Replace the tape.
—
Tracking adjustment is beyond range
of automatic tracking circuit.
Adjust tracking manually using the
SET/TR +/– buttons on the remote
control.
36
Video heads are dirty.
Clean the video heads.
51
The remote control is not aimed at
the sensor.
Aim the remote control at the
remote sensor.
10
Distance is too far or too much light in
the room.
Operate within 15 feet or reduce the
light of the room.
10
There is an obstacle in the path of
the beam.
Clear the path of the beam.
The batteries are weak.
Replace the batteries.
10
The batteries are not inserted
correctly.
Insert correctly.
10
RECORDING
TV recording does not work.
Timer recording does not
work.
42, 43
PLAYBACK
Noise bars appear on the
screen.
REMOTE CONTROL
Remote control does not
operate.
10
49
5E20101B P44-BACK
49
14/08/2003, 15:50
RECEPTION DISTURBANCES
Most types of television interference can be remedied by adjusting the height and position of the VHF/UHF
antenna. Outdoor antennas are recommended for best results. The most common types of television interference are shown below. If one of these symptoms appear when the TV/VCR is connected to a Cable TV system,
the disturbance may be caused by the local Cable TV company broadcast.
IGNITION
Black spots or horizontal streaks may appear, the picture may flutter or
drift. Usually caused by interference from automobile ignition systems,
neon lamps or AC powered tools and appliances such as drills or hair
dryers.
GHOSTS
Ghosts are caused by the television signal following two paths. One is the
direct path and the other is reflected by tall buildings, hills or other large
objects. Changing the direction or position of the antenna may improve the
reception.
SNOW
If the TV/VCR is located far from the TV station, in a fringe reception
area where the signal is weak, small dots may appear in the picture.
If the signal is extremely weak, the installation of a larger external
antenna may be necessary.
RADIO FREQUENCY INTERFERENCE (RFI)
Caused by two-way radios, this type of interference produces moving
ripples or diagonal streaks in the picture. Some cases may cause a loss of
contrast in the picture. Changing the direction and position of the antenna
or installing an RFI filter may improve the picture.
PICTURE SIZE VARIATION
A slight picture size variation is normal when you adjust the CONTRAST or
BRIGHTNESS settings.
CARE AND MAINTENANCE
To prevent fire or shock hazard, disconnect the TV/VCR from the AC power sources before cleaning.
The finish on the cabinet may be cleaned with mild soap and a soft, damp cloth and cared for as other furniture. Use
caution when cleaning or wiping the plastic parts.
50
5E20101B P44-BACK
50
14/08/2003, 15:50
VIDEO HEAD CLEANING
VIDEO HEAD CLOGGING
The video heads are the means by which the TV/VCR reads the picture from
the tape during playback. In the unlikely event that the heads become dirty
enough to be clogged, no picture will be played back. This can easily be determined if, during playback of a known good tape, there is good sound, but no
picture (picture is extremely snowy). If this is the case, use a high quality head
cleaning system or have them cleaned professionally.
Good Picture
Snowy Picture
Video head cleaning is needed when the playback picture becomes unclear. This signifies that the heads are getting
dirty and can occur when playing poor quality or damaged tapes. If the heads require cleaning, use a equivalent high
quality chemical non-abrasive (wet) head cleaning tape or have them cleaned professionally. If playing a head
cleaning tape in the VCR once does not improve the picture, play it several times before requesting service.
VIDEO HEAD CLEANING
DO NOT ATTEMPT TO CLEAN THE VIDEO HEADS OR SERVICE THE UNIT BY REMOVING THE TOP COVER.
NOTES:
• Video heads may eventually wear out and should be replaced when they fail to produce clear pictures.
• To help prevent video head clogging, use only good quality VHS tapes. Discard worn out tapes.
SPECIFICATIONS
TELEVISION
Picture Tube:
Tuner Type:
Receiving Channels:
Antenna Input:
Speaker:
Audio Output Power:
VCR
Video System:
Video Signal:
Cassette Tape:
Audio Track:
Tape Speed:
F.FWD/REW Time:
Speed Search:
MV13N2/W
Type 13 (335.4 mm diagonal)
Quartz PLL Frequency Synthesized
VHF
2-13
UHF
14-69
CATV
14-36 (A)-(W)
37-59 (AA)-(WW)
60-85 (AAA)-(ZZZ)
86-94 (86)-(94)
95-99 (A-5)-(A-1)
100-125 (100)-(125)
01 (5A)
VHF/UHF In 75 ohms coaxial
1-1/2 x 2-1/2 inches (38 x 63 mm), 8 ohm
1.5W
MV19N2/W
Type 19 (480.0 mm diagonal)
3 inches (76 mm), 8 ohm
1.5W
VHS, 2 Rotary Heads Helical Scanning System
NTSC Color
VHS
1 Track
SP:
33.35 mm/sec.
SLP:
11.12 mm/sec.
F.FWD: Approx. 4 minutes 50 seconds (T-120 Cassette) at 25˚C (77˚F)
REW:
Approx. 2 minutes 30 seconds (T-120 Cassette) at 25˚C (77˚F)
SP
3 & 5 x Normal Speed
SLP
9 & 15 x Normal Speed
GENERAL
Power Source:
Power Consumption:
Dimensions:
AC 120V 60Hz
65 Watts
Width:
14-1/4 inches (362 mm)
Height: 15-1/16 inches (382 mm)
Depth:
14-3/8 inches (365 mm)
Weight:
24.3 Ibs. (11 kg)
Terminals:
Video In: (RCA) 1 Vp-p/75 ohm
Audio In: (RCA) –8 dBm/50K ohm
Storage Temperature:
–20°C to 60°C (–4°F to 140°F)
Operating Temperature: 5°C to 40°C (41°F to 104°F)
Remote Control:
Infrared, Direct Access, 2 x AAA batteries
Accessories:
300-75 ohm Matching Transformer
Remote Control
Batteries (2 x AAA)
86 Watts
Width:
19-1/4 inches (489 mm)
Height:
19-1/8 inches (486 mm)
Depth:
18-5/16 inches (465 mm)
41.8 Ibs. (19 kg)
51
Specifications are subject to change without notice.
Tape Speed shown is approximate.
5E20101B P44-BACK
51
14/08/2003, 15:50
LIMITED WARRANTY TOSHIBA COMBINATION TELEVISION
AND VIDEO CASSETTE RECORDER
Toshiba America Consumer Products, Inc. (“TACP”) and Toshiba Hawaii Inc. (“THI”) make the following limited
warranties. These limited warranties extend to the original consumer purchaser or any person receiving this set as a
gift from the original consumer purchaser and to no other purchaser or transferee.
Limited Ninety (90) Day Warranty
TACP and THI warrant this product and its parts against defects in materials or workmanship for a period of ninety
(90) days after the date of original retail purchase. During this period, TACP and THI will repair a defective product or
part, without charge to you. You must deliver the entire set to an Authorized TACP/THI Service Station. You pay for
all transportation and insurance charges for the set to and from the Service Station.
Limited One (1) Year Warranty
TACP/THI further warrant the parts in this product against defects in materials or workmanship for a period of one
year after the date of original retail purchase. During this period TACP/THI will replace a defective part without
charge to you, except that if a defective part is replaced after ninety (90) days from the date of original retail purchase
you pay labor charges involved in the replacement. You must also deliver the entire product to a TACP/THI Authorized Service Station. You are responsible for all transportation for the set to and from the Service Station.
Limited Two (2) Year Warranty of Picture Tube
TACP and THI further warrant the picture tube in this product against defects in materials or workmanship for a
period of two (2) years after the date of original retail purchase. During this period, TACP/THI will replace a defective
picture tube without charge to you except that if a defective picture tube is replaced after ninety (90) days from the
date of the original retail purchase, you pay labor charges involved in the replacement. You are responsible for all
charges involved in the replacement. you are responsible for all transportation and insurance charges for the set to
and from the Service Station.
Rental Units
The warranty for rental units begins with the first rental or thirty (30) days from the date of shipment to the rental firm,
whichever comes first.
Commercial Units
Products sold and used for commercial use have a limited ninety (90) day warranty for all parts, labor and picture tube.
Owner's Manual and Demographic Card
You should read this owner's manual thoroughly before operating this product. You should complete and mail the
enclosed Demographic card within ten days after you, or the person who has given you this product as a gift,
purchased this product. This is one way to enable TACP/THI to provide you with better customer service and
improved products. Failure to return the Demographic card will not affect your rights under this warranty.
Your Responsibility
The above warranties are subject to the following conditions:
( 1 ) You must retain your bill of sale or provide other proof of purchase.
( 2 ) All warranty servicing of this product must be made by an Authorized TACP/THI Service Station.
( 3 ) These warranties are effective only if the product is purchased and operated in the U.S.A. or Puerto Rico.
( 4 ) Labor service charges for set installation, set up, adjustment of customer controls and installation or repair of
antenna systems are not covered by this warranty. Reception problems caused by inadequate antenna systems
are your responsibility.
( 5 ) Warranties extend only to defects in materials or workmanship as limited above and do not extend to any
product or parts which have been lost or discarded by you or to damage to products or parts caused by
misuse, accident, damage caused by Acts of God, such as lightning or fluctuations in electric power, improper
installation, improper maintenance or use in violation of instructions furnished by us; or to units which have
been altered or modified without authorization of TACP/THI .
52
5E20101B P44-BACK
52
14/08/2003, 15:50
How to Obtain Warranty Service
If after following all of the operating instructions in this manual and checking the section “PROBLEM AND TROUBLESHOOTING GUIDE” and you still find that service is needed;
( 1 ) Call the TACP toll free number 1-800-631-3811 after you find a defective product or part to find the
nearest Toshiba Authorized Service Station.
( 2 ) Please present your bill of sale or other proof to the Authorized Service Station.
“TACP/THI Authorized Service Station personnel will come to your home when warranty service is required.
Depending on the type of repair required, the service will either be performed in your home or the set will be
taken to the TACP/THI Authorized Service Station for repair and returned to your home at no cost to you”
In the Continental United States contact:
In Hawaii Contact:
Toshiba Hawaii, Inc
327 Kamakee Street,
Honolulu, Hawaii 96814
(808) 591-8377
Toll Free
1-800-631-3811
All warranties implied by state law, including the implied warranties of merchantability and fitness for a particular
purpose, are expressly limited to the duration of the limited warranties set forth above. With the exception of any
warranties implied by state law as hereby limited, the foregoing warranty is exclusive and in lieu of all other warranties,
guarantees, agreements and similar obligations of manufacturer or seller with respect to the repair or replacement of
any parts. In no event shall TACP or THI be liable for consequential or incidental damages.
No person, agent, distributor, dealer or company is authorized to change, modify or extend the terms of these
warranties in any manner whatsoever. The time within which action must be commenced to enforce any obligation of
TACP or THI arising under this warranty or under any statute, or law of the United States or any state thereof, is here
by limited to 90 days from the date you discover or should have discovered, the defect. This limitation does not apply
to implied warranties arising under state law.
This warranty gives you specific legal rights and you may also have other rights which may vary from state to state.
Some states do not allow limitation on how long an implied warranty lasts, when an action may be brought, or the
exclusion or limitation of incidental or consequential damages, so the above provisions may not apply to you.
ATTENTION CANADIAN CONSUMERS:
Canadian consumers are requested to complete the special Canadian “Warranty Registration Form”
enclosed, and forward this completed form with a copy of bill of sale to TOSHIBA OF CANADA to
“Register and Validate” their warranty.
Products purchased in the U.S.A. and used in Canada are not covered by these warranties.
Products purchased in Canada and used in the U.S.A. are not covered by these warranties.
Rev. 09-01-98
53
5E20101B P44-BACK
53
14/08/2003, 15:50
03/07
PRINTED IN THAILAND
U
5E20101B P44-BACK
54
14/08/2003, 15:50
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement