PHILIPS MAGNAVOX PS1966C1 Color Television Quick Use and Setup Guide
Below you will find brief information for Color Television PS1966C1. The guide provides basic information about setting up your television and connecting it to various devices, such as cable TV, antenna, and VCR. The manual will help you understand how to use the onscreen menu controls, set up channels, and program your TV for your specific needs. This quick guide will guide you through the basic steps to get your new television up and running.
Advertisement
Advertisement
Color Television
PS1966C1
Quick Use and Setup Guide
T
ABLE OF
C
ONTENTS
Getting Started
10
9
8
7
11
12
6
5
1
2
4
3
Warning/Precautions........................................1
Basic Television Hookups ...............................1
Basic Television and Remote Operation .......................2
How to Use the Onscreen Menu Controls ....................3
Setting Up Your Television for the First Time ..........3-4
• For details on product registration, warranty, and service refer to the other literature (Owner’s Manual) included with your TV information packet.
Please retain all these materials and keep them handy for future reference.
NOTE: This owner's manual is used with several different television models. Not all features (and drawings) discussed in this manual will necessarily match those found with your television set.
This is normal and does not require you contacting your dealer or requesting service.
WARNING: TO PREVENT FIRE OR SHOCK HAZ-
ARD DO NOT EXPOSE THIS UNIT TO RAIN OR
EXCESSIVE MOISTURE.
H
OOKING
U
P
Y
OUR
TV (B
ASIC
A
NTENNA
/C
ABLE
TV C
ONNECTIONS
)
C
ABLE
TV
C
ABLE
I
NPUT
/C
ONVERTER
Y
our Cable TV input into your home may be a single (75 ohm) cable, or a
Converter Box installation.
In either case the connection to the TV is very easy.
Just put the threaded end of the cable signal to the
TV's antenna plug and screw it down tight.
BEGIN
If your Cable TV signal
is a single round cable (75 ohm) then you're ready to connect to the TV.
If you have a Cable
Converter Box:
Connect the Cable TV signal to the Cable Signal IN(put) plug on the Converter.
NOTE: The connecting cable for the Converter is supplied from the Cable TV Company.
Cable TV Company
IN
Cable TV Converter
Box Connection
Connect the Cable TV cable to the
ANTENNA/CABLE plug on the TV.
If you have a Cable Converter Box:
Connect the OUT(put) plug from the
Converter to the 75
Ω plug on the TV.
Cable TV Signal Input
OUT
OR
Round Cable
75
Ω
Ohm
75
V
1
2
Back of TV
75 V in out
VIDEO
L/MONO
AUDIO
R
1
S
MART
H
ELP
Remember:
Set the TV for the type signal you've just connected (see the “Tuner” section on page 3 of this
Set-Up Guide.)
To select only the channel numbers on your Cable system see “Auto Program"
(page 4). If you use a
Cable Converter box, set the TV to the same channel as the converter's CH 3/4 switch (on the rear of the converter.)
A
NTENNA
C
OMBINATION
UHF/VHF
A
combination antenna receives normal broadcast channels (VHF 2-13 and UHF 14-69). Your connection is easy since there is only one 75
Ω
(ohm) antenna plug on the back of your TV - and that’s where the antenna goes.
BEGIN
If your antenna has a
round cable (75 ohm) on the end, then you're ready to connect it to the TV.
If your antenna has flat twin-lead
wire (300 ohm), you first need to attach the antenna wires to the screws on a 300 to 75 ohm adapter.
1
300 to 75
Ω
Adapter
75 V
Push the round end of the adapter (or antenna) onto the
75
Ω plug on the rear of the TV.
If the round end of the antenna wire is threaded, screw it down tight.
2
Combination VHF/UHF
Antenna
(Outdoor or Indoor)
Twin Lead
Wire
Back of TV
OR
Round Cable
75
Ω
Note: For homes with separate UHF and VHF antennas you will need an optional combiner to connect to the TV.
U/V
Combiner
75 V in out
VIDEO
L/MONO
AUDIO
R
1
Back of TV
75-300 Ohm Adapter
S
MART
H
ELP
Remember, be sure to set the TV for the type signal you've connected
(see the “Tuner” section on page 3 of this Set-Up Guide.)
To set the TV to select only the channel numbers in your area see how to
“Program" or "Add" channels in memory on page 4 (Auto
Program section).
To order any optional accessory contact your dealer or call the toll-free accessory ordering number
(1-800-851-8885).
TV
TO
VCR
B
ASIC
C
ONNECTION
he basic Antenna, or
T
Cable TV, to VCR to
TV connection is shown to the right. For more information on other hookups
(possible when Cable
Converter/Descrambler boxes are included) refer to your accessory VCR and
Cable Converter Owner's
Manual for details.
BEGIN
Connect your
Antenna or Cable TV signal to the IN FROM ANT(enna) plug on the VCR.
Outdoor
VHF/UHF
Antenna
Connect the OUT TO
TV plug on the VCR to the
75
Ω plug on the TV (connecting cable supplied with the
VCR.)
300 to 75
Ω
Ohm Adapter
1
Round Cable
75
Ω
Supplied with VCR
75
V
OR
Refer to the Owner's
Manual included with your
VCR for other possible connections and TV/VCR operating details.
2
IN FROM ANT.
OUT TO TV
Cable TV signal
Back of TV
VCR
Q/U-1 in out
VIDEO
L/MONO
AUDIO
R
3135 015 10901
T
ELEVISION
6
TV
AND
R
EMOTE
C
ONTROL
O
PERATION
BEGIN
Press the POWER
button to turn the TV ON.
Press the VOLUME +
button to increase the sound level or the VOLUME – but-
ton to lower the sound level.
Pressing both buttons at the
same time will display the onscreen menu. Once in the menu, use these button to make adjustments or selections.
Press the CHANNEL UP
▲ or DOWN ▼ button to select TV channels.
STEREO
Remote Sensor Window Audio/Video Input Jacks
(Stereo Audio Jacks)
Slide the TV/VCR/ACC
mode switch on the remote control to the TV position and point the remote at the front of the TV when sending commands.
MENU
POWER
R
EMOTE
B
ATTERY
I
NSTALLATION o load the supplied batT teries into the remote:
1. Remove the battery
compartment lid on the back of the remote.
2. Place the batteries (2-
AA) in the remote. Be sure the (+) and (-) ends of the batteries line up correctly (inside of case is marked.)
3. Reattach the battery lid.
VIDEO L AUDIO R
INSTALL/
MENU
– VOLUME + CHANNEL
– VOLUME + CHANNEL
POWER VIDEO L AUDIO R
1
Point the remote control toward the remote sensor window on the TV when operating the TV with the remote.
Headphone Jack
2
3
POWER
SLEEP
A/CH
STA
TUS/EXIT
RECIRD
TV
VCR
ACC
CC
CLOCK
TV/VCR
SMAR
T
SOUND
MENU
SMAR
T
PICTURE
SURF
MUTE
CH
VOL
3
4
TV/VCR/ACC M
ODE
S
WITCH
The remote's TV/VCR/ACC
Switch controls how buttons on the remote are used.
For example:
With the switch in the "TV"
position: the Menu, CURSOR ©,
©© , §§ and ■ buttons are used to select and adjust onscreen TV features.
With the switch in the
"ACC" position: the Power, Channel
Number, and Channel
Up (+) /Down (–) buttons on the remote work with
Cable TV Converters.
With the switch in the
"VCR" position: the Menu, CURSOR ©,
©© , §§ and ■ buttons on the remote work Stop,
Play, and other VCR features.
Note: For more details on how the TV remote works with VCRs and Cable
Converters, see the other owner's manual supplied with your TV.
Sleep Button
Press to set the TV to automatically turn itself OFF. Also can be used as an Enter button when sending channel commands to remote controlled cable converters or VCRs.
Status/Exit Button
Press to see the current channel number on the
TV screen. Also press to clear the TV screen after control adjustments.
A/CH-Record Button
Press to toggle between the currently viewed channel and the previously viewed channel.
When in the VCR mode, press to start the recording of a video tape.
TV/VCR/ACC Mode Switch
Slide to TV position to control TV functions;
VCR to control VCR functions; and ACC for
Cable Converter, DBS, DVD, etc. functions.
SmartSound™ Button
Press to select from a list of SmartSound controls. (Factory preset sound control levels set for different types of listening, based on the type of programming being used.)
Menu Button
Press for the onscreen menu to appear.
Pressing the menu button after menu selections are made will eliminate the menu from the display.
Cursor Buttons
Use these buttons to select and adjust the
TV's onscreen menu. Also used with a VCR for PLAY, FAST FORWARD, REWIND, and
STOP.
Volume (+), (–) Buttons
Press to adjust the TV sound level.
Mute Button
Press to turn the sound OFF on the TV. Press again to return the sound to its previous level.
S
MART
H
ELP
Remember, You can press any button on the front of the TV to turn the TV
ON.
Q/U-2
POWER
SLEEP
CLOCK A/CH STATUS/EXIT CC
TV RECORD
VCR 1
ACC
4
7
SMART
2
5
8
0
SOUND
MENU
PICTURE
SURF
TV/VCR
3
6
9
VOL
MUTE
CH
The tuned channel number will always briefly appear when the
TV is first turned ON (and with channel changes.)
You can also press the STA-
TUS/EXIT button (on the remote) to see what channel the
TV is ON.
Power Button
Press to turn the TV (or select VCR/
Cable Converter) ON and OFF.
CC Button
Press to select Closed Caption options within the menu. (Refer to the Owner’s
Manual for details.)
Clock-TV/VCR Button
When used in the TV mode, the
CLOCK-TV/VCR button will access the
Clock menu options.
Press while in the VCR mode (VCR indicator on the front of the unit will light) to view the playback of a tape.
Press again to place in the TV position
(VCR indicator light will go off) to view one program while recording another program.
Number Buttons
Press the number buttons to select TV channels. When selecting single digit channels, press the number of the desired channel. The TV will pause for a few seconds then tune to the selected channel. (Note: you can press "0", then the number also.) For channels "100" and above, first press "1" then the next two numbers of the desired channel.
SmartPicture™ Button
Press to select from a list of
SmartPicture controls. (Factory preset picture control levels set for different types of viewing sources and programs.)
Surf Button
Press to select previously viewed channels. You can place up to 8 channels in memory. Then by pressing the SURF button you can quickly view the select channels. See the “Surf" section (in your other owner's manual) to see how to select a series of channels using the Surf button.
When in the VCR mode, pressing this button will pause the playback of a video tape.
Channel (+), (–) Buttons
Press to change the tuned channel.
H
OW TO
U
SE THE
TV’
S ONSCREEN
MENU C
ONTROLS
M ENU
F eatures for your television can be adjusted from within a MENU shown on the TV’s screen. A MENU is nothing more than an 0nscreen list of features. Each
MENU item can be adjusted by viewing the screen and simply press a button.
BEGIN
Press the MENU but-
ton on the remote (or the
Volume (+) or (–) buttons simultaneously on the TV) to show the onscreen menu.
©
Press the CURSOR UP or DOWN ■ buttons on the remote (or the Volume (+) or (–) buttons on the TV) to pick any of the onscreen menu features.
Press the CURSOR
RIGHT
©© or LEFT §§
buttons on the remote (or
Channel ▲ or ▼ buttons on the
TV) to adjust any highlighted onscreen feature.
Press the
STATUS/EXIT button on the remote to clear the screen after an adjustment.
You can also just wait a few seconds after you finish the feature adjustment and the
MENU will disappear from the screen automatically.
1
VOL
MUTE
CH
SMAR
T
ACC
VCR
SLEEP
TV
RECORD
A/CH
STATUS/EXIT
CC
TV/VCR
CLOCK
2
SURF
PICTURE
SMAR
T
POWER
3
SETUP
SmartLock REVIEW
BRIGHTNESS
COLOR
PICTURE
©
©
30
30
30
SHARPNESS
TINT
30
03
COL. TEMP.
CONTRAST PLUS
NORMAL
ON
NOISE REDUCTION ON
VOLUME
BALANCE
TREBLE
BASS
INCREDIBLE SURR
15
05
31
31
ON
SOUND
SAP
AVL
VOLUME LIMITER
INPUT
STEREO
OFF
ON
ON
EXT 1
SLEEPTIMER
SmartLock
CC
CLOCK
SETUP
OFF
©
OFF
©
©
S
MART
H
ELP
If you pass the feature you want, press the CUR-
SOR UP or DOWN button on the remote to move back through the
MENU.
The MENU list is a continuous loop. Once you come to the last item in the list, scrolling down will bring you back to the start of the list again.
The onscreen menu will time out and disappear from the screen when you finish, or you can press the STATUS/EXIT button to clear the menu from the screen.
S
ETTING
U
P
Y
OUR
T
ELEVISION
F
OR THE
F
IRST
T
IME
L
ANGUAGE
F or our Spanish and
French speaking TV owners an onscreen LAN-
GUAGE option is present.
With the LANGUAGE control you can set the TV’s onscreen menu to be shown in either English, Spanish, or
French.
BEGIN
Press the MENU but-
ton on the remote to show the onscreen menu.
CC OFF
CLOCK
SETUP
©
©
SMART LOCK REVIEW
©
BRIGHTNESS 30
Press the CURSOR UP
© or DOWN ■ buttons to scroll through the onscreen menu until the word SETUP is highlighted.
LANGUAGE
TUNER
AUTO PROGRAM
ENGLISH
CABLE
©
Press the CURSOR
RIGHT ©© button to display the SETUP menu features.
LANGUAGE
OR
FRANCAIS
LANGUAGE ESPANOL
Press CURSOR UP ©
or DOWN ■ buttons to scroll the Setup features until the word LANGUAGE is highlighted.
Press the CURSOR
RIGHT ©© button repeat-
edly to select ENGLISH,
ESPANOL (Spanish), or
FRANCAIS (French).
1
SOUND
MENU
SMAR
T
ACC
VCR
SLEEP
TV
RECORD
A/CH
STATUS/EXIT
CC
TV/VCR
CLOCK
POWER
SURF
PICTURE
SMAR
T
4
2
VOL
MUTE
CH
3
5
S
MART
H
ELP
Remember: The
Language control only makes the TV’s onscreen MENU items appear in English, Spanish, or French text.
It does not change the other onscreen text features such as
Closed Caption (CC) TV shows.
The onscreen menu will time out and disappear from the screen when you finish, or you can press the STATUS/EXIT button to clear the menu from the screen.
T
UNER
T he TUNER feature allows you to change the
TV’s signal input to either
CABLE, ANTENNA or AUTO mode. It’s important for the
TV to know if you want to receive channels from a
Cable TV signal or a normal
Antenna signal.
Note: The AUTO mode setting helps the TV determine the type of signal or channels being received when AUTO
PROGRAM is activated.
4
2
1
VOL
MUTE
CH
BEGIN
Press the MENU but-
ton on the remote to show the onscreen menu.
SOUND
MENU
SMAR
T
ACC
VCR
SLEEP
TV
RECORD
A/CH
STATUS/EXIT
CC
TV/VCR
CLOCK
POWER
SURF
PICTURE
SMAR
T
3
5
Press the CURSOR UP
© or DOWN ■ buttons to scroll through the onscreen menu until the word SETUP is highlighted.
CC
CLOCK
OFF
©
SETUP
©
SMART LOCK REVIEW
©
BRIGHTNESS 30
Press the CURSOR
RIGHT ©© button to display the SETUP menu features.
LANGUAGE
AUTO PROGRAM
ENGLISH
©
TUNER
CHANNEL EDIT
EXTERNAL
CABLE
©
©
TUNER
TUNER
AUTO
OR
ANTENNA
Press CURSOR UP ©
or DOWN ■ buttons to scroll the Setup features until the word TUNER is highlighted.
Press the CURSOR
RIGHT
©© button to select either CABLE, ANTENNA
or AUTO mode.
S
MART
H
ELP
Remember, when the
AUTO mode is selected the TV will automatically choose the correct type of signal or channels when
AUTO PROGRAM is activated.
When CABLE is selected, channels
1-125 are available. When ANTEN-
NA is selected, channels 2-69 are available.
The onscreen menu will time out and disappear from the screen when you finish, or you can press the
STATUS/EXIT button to clear the menu from the screen.
Q/U-3
H
OW TO
U
SE THE
SETUP F
EATURES
A
UTO
P
ROGRAM
Y our TV can automatically set itself for local area (or
Cable TV) channels. This makes it easy for you to select only the TV stations in your area when the CHANNEL
(+), (–) buttons are pressed.
Note: Make sure the antenna or cable signal connection has been completed before AUTO
PROGRAM is activated.
BEGIN
Press the MENU but-
ton on the remote to show the onscreen menu.
CC OFF
CLOCK
SETUP
©
©
SMART LOCK REVIEW
©
BRIGHTNESS 30
Press the CURSOR UP
© or DOWN ■ buttons to scroll through the onscreen menu until the word SETUP is highlighted.
LANGUAGE
TUNER
AUTO PROGRAM
CHANNEL EDIT
EXTERNAL
ENGLISH
CABLE
©
©
©
1
SOUND
MENU
SMAR
T
ACC
VCR
SLEEP
TV
RECORD
A/CH
STATUS/EXIT
CC
TV/VCR
CLOCK
POWER
SURF
PICTURE
SMAR
T
4
2
VOL
MUTE
CH
3
5
S
MART
H
ELP
Try it out. Press the
CHANNEL (+), (–) buttons and see which channels have been added to the TV’s memory.
Press the CURSOR
RIGHT ©© button to display the SETUP menu features.
AUTO PROG 33
Press CURSOR UP © or
DOWN ■ buttons to scroll the Setup features until the words AUTO PROGRAM are highlighted.
Press the CURSOR
RIGHT
©© button to start the Auto Program scanning of channels
Auto Program will scan for all available channels within the Antenna/Cable signal.
When finished, the TV will go back to the SETUP menu.
If you want to delete any unwanted channels from the TV’s memory, see the CHANNEL EDIT section below.
The onscreen menu will time out and disappear from the screen when you finish, or you can press the STATUS/EXIT button to clear the menu from the screen.
C
HANNEL
E
DIT
C hannel Edit makes it easy for you to ADD or
DELETE channels from the list of channels stored in the
TV’s memory.
1
VOL
2
4
MUTE
7
SOUND
MENU
SMAR
T
ACC
VCR
SLEEP
TV
RECORD
A/CH
STATUS/EXIT
CC
TV/VCR
CLOCK
POWER
SURF
PICTURE
SMAR
T
6
CH
3
5
7
BEGIN
Press the MENU but-
ton on the remote to show the onscreen menu.
Press the CURSOR UP
© or DOWN ■ buttons to scroll through the onscreen menu until the word SETUP is highlighted.
CC OFF
CLOCK
SETUP
©
©
SMART LOCK REVIEW
©
BRIGHTNESS 30
Press the CURSOR
RIGHT ©© button to display the SETUP menu features.
Press the CURSOR UP
© or DOWN ■ buttons to scroll the Setup features until the words CHANNEL EDIT are highlighted.
Press the CURSOR
RIGHT ©© button to display the CHANNEL EDIT options.
With the CHANNEL
EDIT options displayed, and the word CHANNEL highlighted; enter the channel number
(with the NUMBERED or the
CURSOR RIGHT © or LEFT
§ buttons) you wish to ADD, or
DELETE from the TV’s memory.
Scroll down (using the
CURSOR UP © or DOWN
■ buttons) to highlight the word SAVED.
Now use the CURSOR
RIGHT ©© button to toggle between YES or NO.
If YES is selected the menu reads “CHANNEL ADDED” and the channel is added to the
TV’s memory. If NO is select-
ed the menu reads “CHAN-
NEL DELETED” and the channel is deleted from the
TV’s memory.
TUNER
AUTO PROGRAM
CHANNEL EDIT
EXTERNAL
CABLE
©
©
©
CHANNEL
SAVED
CHANNEL ADDED
2 CHANNEL
SAVED
CHANNEL DELETED
2
NO
E
XTERNAL he External feature T allows you to rename your input source selections.
When the Input feature (refer to Owner’s Manual for details) is accessed to change audio/video jacks, your source selection will be called by the name you choose. This name will also appear onscreen when using the audio/video inputs.
BEGIN
Press the MENU but-
ton on the remote to show the onscreen menu.
CLOCK
CC
SETUP
AutoLock REVIEW
BRIGHTNESS
©
OFF
©
©
30
1
SOUND
MENU
AUTO
ACC
VCR
SLEEP
TV
RECORD
A/CH
STATUS/EXIT
CC
TV/VCR
CLOCK
POWER
SURF
PICTURE
AUTO
4
2
VOL
MUTE
CH
3
5
6
©
Press the CURSOR UP
or DOWN ■ buttons to scroll through the onscreen menu until the word SETUP is highlighted.
Press the CURSOR
RIGHT ©© button to display the SETUP menu features.
Press the CURSOR UP ©
or DOWN ■ buttons to scroll the Setup features until the word
EXTERNAL is highlighted.
With the External options menu displayed, press the
CURSOR RIGHT
©© but-
ton to select a name from the list: EXT, GAM, DVD, VCD,
VCR, LD, or SAT.
Press the CURSOR
RIGHT
©© button to activate the External feature.
AUTO PROGRAM
CHANNEL EDIT
EXTERNAL
©
©
©
EXT 1 EXT
EXT 1
EXT 1
EXT 1
EXT 1
EXT 1
EXT 1
GAM
DVD
VCD
VCR
LD
SAT
S
MART
H
ELP
Remember: This feature will rename your external signal source and appear onscreen with the new name.
The onscreen menu will time out and disappear from the screen when you finish, or you can press the STATUS/EXIT button to clear the menu from the screen.
Q/U-4

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Easy-to-use onscreen menu controls
- Variety of input and output options
- Stereo audio jacks
- Headphone jack
- Remote control with dedicated buttons for TV, VCR, and Cable Converter control
- SmartSound™ and SmartPicture™ presets for optimized audio and video performance
- Surf button for quick access to previously viewed channels