GE 7-4853 Clock Radio

GE 7-4853 Clock Radio
FCC Information
FCC Information
For Your Safety
This device generates and uses radio frequency
(RF) energy, and if not installed and used properly,
this equipment may cause interference to radio
and television reception.
These rules are designed to provide reasonable
protection against radio and television
interference in a residential installation. However,
there is no guarantee that interference will not
occur in particular installations.
If this equipment does cause interference to radio
or television reception (which you can determine
by unplugging the unit), try to correct the
interference by one or more of the following
measures:
• Reorient the receiving antenna (that is, the antenna for the radio or television that is “receiving” the interference).
• Move the unit away from the equipment that is
receiving interference.
• Plug the unit into a different wall outlet so that
the unit and the equipment receiving interference are on different branch circuits.
If these measures do not eliminate the
interference, please consult your dealer or an
experienced radio/television technician for
additional suggestions. Also, the Federal
Communications Commission has prepared a
helpful booklet, “How To Identify and Resolve
Radio TV Interference Problem.” This booklet is
available from the U.S. Government Printing
Office, Washington, DC 20402. Please specify
stock number 004-000-00345-4 when ordering
copies.
This equipment has been type tested and found
to comply with the specifications in Subpart J of
Part 15 of FCC Rules.
The AC power plug is
polarized (one blade is wider
than the other) and only fits
into AC power outlets one
way. If the plug will not go
into the outlet completely,
turn the plug over and try to insert it the other
way. If it still does not fit, contact a qualified
electrician to change the outlet, or use a different
one. Do not attempt to bypass this safety feature.
WARNING: TO PREVENT FIRE
OR ELECTRICAL SHOCK HAZARD,
DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.
EN
For Your Records
In the event that service should be required, you
may need both the model number and the serial
number. In the space below, record the date and
place of purchase:
Date of Purchase:
Place of Purchase:
Service Information
This product should be serviced only by those
specially trained in appropriate servicing
techniques. For instructions on how to obtain
service, refer to the warranty included in this
Guide.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THE LIGHTNING
FLASH AND ARROWHEAD WITHIN THE
TRIANGLE IS A
WA R N I N G S I G N
ALERTING YOU OF
"DANGEROUS
VOLTAGE" INSIDE
THE PRODUCT.
CAUTION: TO REDUCE THE
RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER
(OR BACK). NO USERS E RV I C E A B L E PA R T S I N SIDE. REFER SERVICING
TO QUALIFIED SERVICE
PERSONNEL.
THE EXCLAMATION
POINT WITHIN THE
TRIANGLE IS A
WARNING
SIGN
ALERTING YOU OF
I M P O R T A N T
INSTRUCTIONS
A C C O M PA N Y I N G
T H E P R O D U C T.
SEE MARKING ON BOTTOM / BACK OF PRODUCT
1
Untitled-2
1
1/16/02, 5:49 PM
Battery Back-Up Operation
This clock radio is equipped with a memory
holding system that can be powered with
a 9-volt battery (not included). The power
failure protection circuit will not operate
unless battery is installed.
When normal household power is interrupted, or AC line cord is unplugged, the
battery will power the clock radio to keep
track of time and alarm settings programmed into memory. When the battery
backup functions, the digital display will
not light, however, the function of alarm
still occurs during the power interruption
and the radio still operates if remaining
battery power is adequate. Normal operation will resume after AC power is restored so you will not have to reset the
time or the alarm.
EN
Install battery as follows:
1. Remove battery compartment door (located on the back of the radio) by applying thumb pressure to area indicated
on battery door and then lift the door
out and off the cabinet.
2. Connect a 9-volt battery connector plug.
3. Insert battery in the compartment and
replace the compartment door.
Power Failure Indicator
When AC power is interrupted (disconnected) for a short period of time, both
time and alarm settings will change (unless optional battery is installed). After AC
power is restored (reconnected), the Digital Display will blink to indicate that power
was interrupted and you should readjust
the time and alarm settings.
Note: Alkaline (NEDA 1604A / IEC 6LR61) battery is
recommended. Carbon Zinc (NEDA 1604 / IEC 6F22) battery may be used but memory holding time will be substantially reduced. Memory holding time for a fresh alkaline battery is
approximately 8 hours (if radio or alarm is not operated), which should
take care of short, nuisance-type AC power failures. To preserve
battery life, the radio should remain plugged into an AC outlet. As
batteries get older, their voltage drops and memory may be lost. Be
sure to replace the battery periodically. Battery should be removed
if the radio will be stored for more than one day. Leaky batteries
may badly damage the clock radio.
2
Untitled-2
2
1/16/02, 5:49 PM
Operating the Radio
EN
+ VOLUME TUNING
Tuning the Stations
1. Plug the power cord into any 120-V AC
household outlet.
2. Press ON/OFF (located on the top of the
alarm) to turn on the radio.
3. Slide the AM/FM switch (located on the
side of the unit) to the desired broadcast band.
4. Turn TUNING to select a station.
5. Adjust the sound amount by VOLUME.
6. Press ON/OFF to turn off the radio
Built-In AFC
The Built In Automatic Frequency Control
(AFC) works only on FM. It helps reducing
drift on FM reception and keeping the
radio locked in on the FM station to which
it is tuned.
When tuning in FM stations, you may notice that the station you are tuning can
be well-tuned on two or three nearby
points on the dial. Always tune carefully
at the loudest and clearest point.
Antennas
AM Antenna-A built-in ferrite rod antenna
eliminates the need for an outside antenna for AM reception. Rotating the unit
slightly may improve reception of distant
AM stations.
3
Untitled-2
3
1/16/02, 5:49 PM
Operating the Clock
EN
CLOCK
REV
WAKE 1
FWD
WAKE 2
NAP
WAKE 1 WAKE 2
PRESS
HOLD TO CANCEL
SLEEP
SNOOZE
ON/OFF
Setting Clock Time
Your digital clock operates on a 12-hour
standard mechanism. A green indicator
will be shown below to AM when the unit
is reading AM time.
1. Slide the funciton selector to CLOCK.
2. Press REV or FWD to set the clock time.
When you press and hold REV or FWD,
the time decrements or increments will
follow by a fast rate. No adjustment
can be made when mode is selected.
Setting the Wake Time
This clock radio has two separate alarms.
You need to set each of them individually.
1. Slide the function selector to WAKE 1
or WAKE 2.
2. Press REV or FWD to set the wake time.
The time decrements or increments will
follow by a fast rate when you press and
hold REV or FWD.
3. Wake time is set. A green indicator is
up on the left-hand side when WAKE 1
is activated while on the right-hand side
when WAKE 2 is activated.
4. To disable WAKE function, press and
hold WAKE 1 or WAKE 2 button until
the indicator disappears.
Note: The unit equips with GRAD-UWAKE feature, the alarm tone volume will increase gradually to its
maximum in about 30 to 45 seconds.
4
Untitled-2
4
1/16/02, 5:49 PM
Operating the Clock
Sleeping Mode
FM
108
AM
NAP
104
AM
170
140
110
85
100
96
1
2
In sleeping mode, the radio will turn off
automatically. Simply:
70
92
60
88
53
x10
kHz
MHz
EN
Waking by Selected Source
Programme
You may be woken up by music or alarm.
1. Select an AM or FM station. (refer to
“Tuning the Stations”)
2. Set wake time (see above direction).
3. Press the current setting alarm mode
(WAKE 1 or WAKE 2 to select waking
up by music or alarm. A green indicator
is up next to the selected setting.
4. Adjust the volume by turning VOLUME.
Note: When you turn off the alarm
or the radio by pressing ON/OFF, the
alarm or the radio will turn on at the
same time tomorrow.
1. Press SLEEP then the time display will
exhibit 0:59 and the radio will turn on.
2. While holding SLEEP, press REV or FWD
to set the sleep time. The time range is
from 1 minute to 2 hours.
3. Release SLEEP and the current time will
be shown again. The radio is turned
on and you may select the station as
usual. The radio will turn off when the
preset time elapses. If you decide to
turn off the radio sooner, press SNOOZE
or ON/OFF.
4. When SLEEP is activated again, the
sleep time will be the same as the one
you have set before.
5. Press SLEEP to read the remaining sleep
time.
Sleeping Mode and Waking
by Selected Source
Programme
You may set your digital clock radio to lull
you to sleep. The radio will turn off and
wake you up at the preset time.
1. Set the wake time.
2. Follow the steps under “Waking by
Selected Source Programme” and
“Sleeping Mode”.
5
Untitled-2
5
1/16/02, 5:49 PM
Operating the Clock
Stop the alarm
EN Nap Mode
This function wakes you up after a short
period of time. Simply:
1. Press NAP and release. The green NAP
indicator will flash. During this time
period, adjust NAP time by pressing REV
or FWD. The range is from 10 minutes
to 2 hours.
2. The clock will be shown after 5 seconds
if no buttons are pressed. The NAP
indicator will lit up.
3. Press NAP once to show time left.
Stop the Nap alarm
Press NAP or follow “Turning off Alarm”.
Notes:
1. Press and hold NAP to cancel the
nap setting.
2. Only alarm sound can be selected.
3. Nap alarm is equipped with
GRAD-U-WAKE feature.
4. If the radio is currently on, then
the radio will be on after NAP is
pressed.
Turning off Alarm
Silence the alarm momentarily
Press SNOOZE. The alarm will sound again
when the snooze period is over. (see
“Snooze Alarm Operation”).
Press ON/OFF. Then, the alarm will be on
the following day at the same time.
Disable the alarm permanently
Press and hold WAKE 1 or WAKE 2 until
the green indicator disappears.
Snooze Alarm Operation
This operation allows extra sleep time after the alarm is on. The alarm will be off
by pressing SNOOZE until the snooze period is over. Snooze function can be used
repeatedly up to 2 hours. After this, the
alarm will turn off until the next alarm
conditions are met. Set the “quiet” as follow:
1. Press and hold SNOOZE.
2. Press REV or FWD to set the “quiet”
period (the default time is 9 minutes)
from 1 minute to 30 minutes. Release
button, then, the “quiet” period is set.
Seconds Time Display
The unit may display in seconds.
1. Select LOCK in the function selector.
2. Press REV or FWD to show seconds display.
3. Release REV or FWD to return to the
hour and minute display.
6
Untitled-2
6
1/16/02, 5:49 PM
US Warranty
What your warranty cover:
EN
• Any defect in material or workmanship.
For how long after our purchase:
• One year.
(The warranty period for rental units begins with the first rental or 45 days from date of shipment to
the rental firm, whichever comes first.)
What we will do:
• Provide you with a new or, at our options, a refurbished unit.
• The exchange unit is under warranty for the remainder of the original product’s warranty period.
How to make a warranty claim:
• Properly pack your unit. Included any cables, etc., which were originally provided with the product.
We recommend using the original carton and packing materials.
• Included in the package evidence of purchase date such as the bill of sale. Also print your name and
address and a description of the defect. Send standard UPS or its equivalent to:
Thomson multimedia Inc.
Product Exchange Center
11721 B Alameda Av.,
Socorro, TX 79927
• Pay any charges billed to you by the Exchange Center for service not covered by the warranty.
• Insure your shipment in case of loss or damage. Thomson accepts no liability in case of damage or
loss.
• A new or refurbished unit will be shipped to you prepaid freight.
What your warranty does not cover:
• Customer instruction. (Your Owner’s Manual provides information regarding operating instructions
and user controls. For additional information, ask your dealer.)
• Installation and set-up service adjustments.
• Batteries.
• Damage from misuse or neglect.
• Products which have been modified or incorporated into other products.
• Products purchased or serviced outside USA.
• Acts of God, such as but not limited to lightning damage.
How state law relates to this warranty:
• This warranty gives you specific legal rights, and you may have other rights which vary from state to
state.
If you purchased your product outside the USA:
• This warranty does not apply. Contact your dealer for warranty information.
7
Untitled-2
7
1/16/02, 5:49 PM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement