GE 7-4894 Clock Radio

GE 7-4894 Clock Radio
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THE LIGHTNING
FLASH AND ARROWHEAD WITHIN THE
TRIANGLE IS A
WA R N I N G S I G N
ALERTING YOU OF
"DANGEROUS
VOLTAGE" INSIDE
THE PRODUCT.
CAUTION: TO REDUCE THE
RISK OF ELECTRIC SHOCK,
D O N OT R E M OV E C OV E R
( O R BAC K ) . N O U S E R S E RV I C E A B L E PA RT S I N S I D E . R E F E R S E RV I C I N G
T O Q UA L I F I E D S E RV I C E
PERSONNEL.
THE EXCLAMATION
POINT WITHIN THE
TRIANGLE IS A
WARNING
SIGN
ALERTING YOU OF
I M P O R TA N T
INSTRUCTIONS
A C C O M PA N Y I N G
T H E P R O D U C T.
SEE MARKING ON BOTTOM / BACK OF PRODUCT
WARNING: TO PREVENT FIRE OR ELECTRICAL
SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.
7-4894 EN-US
1
1/6/03, 8:33 AM
FCC Information
FCC Information
For Your Safety
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two
conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
In accordance with FCC requirements, changes or
modifications not expressly approved by Thomson
multimedia Inc. could void the user’s authority to
operate this product.
This device generates and uses radio frequency
(RF) energy, and if not installed and used properly,
this equipment may cause interference to radio
and television reception.
If this equipment does cause interference to radio
or television reception (which you can determine
by unplugging the unit), try to correct the
interference by one or more of the following
measures:
• Re-orient the receiving antenna (that is, the
antenna for the radio or television that is
“receiving” the interference).
• Move the unit away from the equipment that is
receiving interference.
• Plug the unit into a different wall outlet so that
the unit and the equipment receiving interference
are on different branch circuits.
If these measures do not eliminate the
interference, please consult your dealer or an
experienced radio/television technician for
additional suggestions. Also, the Federal
Communications Commission has prepared a
helpful booklet, “How To Identify and Resolve
Radio TV Interference Problems.” This booklet is
available from the U.S. Government Printing
Office, Washington, DC 20402. Please specify stock
number 004-000-00345-4 when ordering copies.
EN
The AC power plug is
polarized (one blade is wider
than the other) and only fits
into AC power outlets one
way. If the plug will not go
into the outlet completely,
turn the plug over and try to insert it the other
way. If it still does not fit, contact a qualified
electrician to change the outlet, or use a different
one. Do not attempt to bypass this safety feature.
For Your Records
In the event that service should be required, you
may need both the model number and the serial
number. In the space below, record the date and
place of purchase:
Date of Purchase:
Place of Purchase:
Service Information
This product should be serviced only by those
specially trained in appropriate servicing
techniques. For instructions on how to obtain
service, refer to the warranty included in this
Guide.
1
7-4894 EN-US
2
1/6/03, 8:33 AM
Battery Back-Up Operation
This clock radio is equipped with a memory
holding system that can be powered with
2 AA batteries (included). The power failure protection circuit will not operate unless battery is installed.
When normal household power is interrupted, or AC line cord is unplugged, the
batteries will power the clock radio to
keep track of time and alarm settings programmed into memory. When the battery
backup functions, the digital display will
not light, however, the function of alarm
still occurs during the power interruption
if remaining battery power is adequate.
Normal operation will resume after AC
power is restored so you will not have to
reset the time or the alarm.
EN
Install battery as follows:
1. Remove battery compartment door (located at the
bottom of the radio) by
applying thumb pressure
to area indicated on battery door and then lift the
door out and off the cabinet.
2. Connect 2 AA battery to
the connector plug.
3. Insert battery in the compartment and replace the
compartment door.
Power Failure Indicator
When AC power is interrupted (disconnected) for a short period of time, both
time and alarm settings will change (unless optional battery is installed). After AC
power is restored (reconnected), the Digital Display will blink to indicate that power
was interrupted and you should readjust
the time and alarm settings.
+
OPEN/CLOSE
OPEN/CLOSE
(UM3/AA/R6X2)
-
Removble direction of Battery Door
2
7-4894 EN-US
3
1/6/03, 8:33 AM
Operating the Clock
EN
Time/Date selector
This unit has a built-in automatic
time set system, basically you do not
have to set the clock manually. However, in case the memory holding batteries are accidentally removed, you
may reset the clock as follow:
Tip: No icon will be flashing if all selectors are in LOCK mode, if you see any icon
flashing on display, check the Time/Date
selector or the SET switch.
Setting date:
1. Slide the Time/Date selector switch to
DATE.
2. Press REV or FWD to set the date, No
adjustment can be made when the
Time/Date selector is in LOCK mode
Setting time:
1. Slide the Time/Date selector switch to
CLOCK
.
2. Press REV or FWD to set the time, No
adjustment can be made when the
Time/Date selector is in LOCK mode
4
7-4894 EN-US
4
1/6/03, 8:33 AM
Operating the Radio
EN
Tuning the Stations
Antennas
1. Press ON/OFF (located on the top of the
radio) to turn on the radio.
2. Slide the FM/AM switch to the desired
broadcast band.
3. Turn TUNING to select a station.
4. Press ON/OFF to turn off the radio
AM Antenna-A built-in ferrite rod antenna
eliminates the need for an outside antenna for AM reception. Rotating the unit
slightly may improve reception of distant
AM stations.
Built-In AFC
The Built In Automatic Frequency Control
(AFC) works only on FM. It helps reducing
drift on FM reception and keeping the
radio locked in on the FM station to which
it is tuned.
When tuning in FM stations, you may notice that the station you are tuning can
be well-tuned on two or three nearby
points on the dial. Always tune carefully
at the loudest and clearest point.
4
7-4894 EN-US
5
1/6/03, 8:33 AM
Operating the Clock
EN
Setting the WAKE Time
Your digital clock operates on a 12-hour
standard mechanism. A green indicator
will be shown next to AM when the unit
is reading AM time.
1. Slide the SET switch to WAKE 1 or
WAKE 2. (An indicator is activated.)
2. Press REV or FWD to set the wake time.
The time decrements or increments will
follow by a faster rate when you press
and hold either REV or FWD.
3. After WAKE time is set, slide the SET
switch to LOCK position.
Tip: The unit equips with GRAD-U-WAKE
feature, the alarm tone volume will increase gradually to its maximum in about
30 to 45 seconds.
Waking by Selected Source
Programme
You may be woken up by music
alarm
or
.
1. Select an AM or FM station.
2. Set wake time (see above direction).
3. Press the WAKE 2 or WAKE 1 button
to select waking up by music or alarm.
A green indicator is up next to the selected setting.
4. Adjust the volume by turning VOLUME.
Note: When you turn off the alarm or
the music
by pressing ON/OFF
ON/OFF, the
alarm or the music
same time tomorrow.
will turn on at the
Tips: If you set SLEEP function with low
volume level before going to bed, we advise using ALARM
mode to wake you up
since its volume will automatically increase.
5
7-4894 EN-US
6
1/6/03, 8:33 AM
Operating the Clock
EN
Sleep Mode
Stop the Nap alarm
In sleep mode, the radio will turn off automatically. Simply:
Press NAP or follow “Turning off Alarm”.
1. Press SLEEP then the time display will
exhibit 0:59 and the radio will turn on.
2. While holding SLEEP, press REV or FWD
to set the sleep time. The time range is
from 1 minute to 2 hours.
3. Release SLEEP and the current time will
be shown again. The radio is turned
on and you may select the station as
usual. The radio will turn off when the
preset time elapses. If you decide to
turn off the radio sooner, press SNOOZE
or ON/OFF.
4. When SLEEP is activated again, the
sleep time will be the same as the one
you have set before.
5. Press SLEEP to read the remaining sleep
time.
Nap Mode
This function wakes you up after a short
period of time. Simply:
1. Press NAP and release. The green NAP
indicator will flash. During this period,
adjust NAP time by pressing REV or
FWD. The range is from 10 minutes to
2 hours.
2. The clock will be shown after 5 seconds
if no button is pressed. The NAP indicator will lit up.
3. Press NAP once to show time left.
1. Press and hold NAP to cancel the nap
setting.
2. Only alarm sound can be selected.
3. Nap alarm is equipped with GRAD-UWAKE feature.
Turning off Alarm
Silence the alarm momentarily
Press SNOOZE. The alarm will sound again
when the snooze period is over. (see
“Snooze Alarm Operation”).
Stop the alarm
Press ON/OFF. Then, the alarm will be on
the following day at the same time.
Disable the alarm permanently
1. Press CANCEL button.
2. The WAKE indicator will be flashing.
3. Press WAKE 1 or WAKE 2 button within
3 seconds to deactivate the corresponding
alarm function permanently.
Tip: You can activate the previously
set alarm time by pressing WAKE 1
or WAKE 2 button
6
7-4894 EN-US
7
1/6/03, 8:33 AM
Operating the Clock
Snooze Alarm Operation
Seconds Time Display
This operation allows extra sleep time after the alarm is on. The alarm will be off
by pressing SNOOZE until the snooze period is over. Snooze function can be used
repeatedly up to 2 hours. After this, the
alarm will turn off until the next alarm
conditions are met. Set the “quiet” period as follow:
The unit may display in seconds.
1. Select LOCK in the SET switch.
2. Press REV or FWD to show seconds
display.
3. Release REV or FWD to return to the
hour and minute display.
EN
1. Press and hold SNOOZE.
2. Press REV or FWD to set the “quiet”
period (the default time is 9 minutes)
from 1 minute to 30 minutes. Release
button, then, the “quiet” period is set.
Weekend cancel
If the weekend cancel function is activated, the alarm will be active during
MON to FRI, and inactive during SAT and
SUN. You can activate or deactivate this
function as follow:
To activate Weekend cancel function
• Press the Weekend cancel button once
(the red icon “Weekend Cancel” will appear.)
To deactivate Weekend cancel function
• Press and hold the Weekend cancel
button to cancel this function (the red
icon “Weekend Cancel” will disappear.)
7
7-4894 EN-US
8
1/6/03, 8:33 AM
Operating the Clock
EN
SET switch
Before you Plug for Power
Auto Clock Set
1. Setting Time Zone
You may slide the time
zone selector at the bottom of the clock to Eastern, Central, Mountain
or Pacific.
You do not have to set the clock time as a
built-in automatic time set system is
equipped in this clock powered by 3V (2
X AA batteries (included). All you have to
do is to plug this clock for power and current time will be shown automatically.
However, the batteries can also be exhausted and we recommend that you replace the batteries every 3-5 years.
MOUNTAIN
PACIFIC
CENTRAL
EASTERN
2. Day Light Saving
You can slide the DAY
LIGHT SAVING switch at
the side of the unit to turn
on/ off in areas observing/
not observing such time
change.
WARNING: Please avoid playing with
these buttons after entering the
Clock/Alarm set mode.
8
7-4894 EN-US
9
1/6/03, 8:33 AM
US Limited Warranty
What your warranty covers:
• Defects in materials or workmanship.
EN
For how long after your purchase:
• One year from date of purchase.
The warranty period for rental units begins with the first rental or 45 days from date of shipment to the
rental firm, whichever comes first.
What we will do:
• Provide you with a new, or at our option, a refurbished unit. The exchange unit is under warranty for
the remainder of the original product’s warranty period.
• Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that the product
is within the warranty period must be presented to obtain warranty service. For rental firms, proof of
first rental is also required.
How to make a warranty claim:
• Properly pack your unit. Include any cables, etc., which were originally provided with the product.
We recommend using the original carton and packing materials.
• Include evidence of purchase date such as the bill of sale. Also print your name and address and a
description of the defect. Send via standard UPS or its equivalent to:
Thomson multimedia Inc.
Product Exchange Center
11721 B Alameda Avenue
Socorro, Texas 79927
• Insure your shipment for of loss or damage. Thomson accepts no liability in case of damage or loss en
route to Thomson.
• Pay any charges billed to you by the Exchange Center for service not covered by the warranty.
• A new or refurbished unit will be shipped to you freight prepaid.
What your warranty does not cover:
• Customer instruction. (Your Owner’s Manual provides information regarding operating Instructions
and user controls. For additional information, ask your dealer.)
• Installation and set-up service adjustments.
• Batteries.
• Damage from misuse or neglect.
• Products which have been modified or incorporated into other products.
• Products purchased or serviced outside the USA.
• Acts of nature, such as but not limited to lightning damage.
9
7-4894 EN-US
10
1/6/03, 8:33 AM
US Limited Warranty
Limitation of Warranty:
• THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PRODUCT. ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED (INCLUDING ALL IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) ARE HEREBY DISCLAIMED. NO
VERBAL OR WRITTEN INFORMATION GIVEN BY THOMSON MULTIMEDIA INC., ITS AGENTS OR
EMPLOYEES SHALL CREATE A GUARANTY OR IN ANY WAY INCREASE THE SCOPE OF THIS
WARRANTY.
• REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY
OF THE CONSUMER. THOMSON MULTIMEDIA INC. SHALL NOT BE LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF
ANY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. THIS DISCLAIMER
OF WARRANTIES AND LIMITED WARRANTY ARE GOVERNED BY THE LAWS OF THE STATE OF
INDIANA. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED
TO THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE.
EN
How state law relates to this warranty:
• Some states do not allow the exclusion nor limitation of incidental or consequential damages, or
limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply
to you.
• This warranty gives you specific legal rights, and you also may have other rights that vary from state
to state.
If you purchased your product outside the USA:
This warranty does not apply. Contact your dealer for warranty information.
10
7-4894 EN-US
11
1/6/03, 8:33 AM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement