LG FLATRON 680LE TFT LCD monitor User manual

Contents

ENGLISH

Introduction ...........................................................A1

Connecting the Monitor.........................................A2

Location and Function of Controls ........................A3

Control Panel Function ..........................................A4

On Screen Display (OSD) Control Adjustment ....A5

On Screen Display(OSD) Selection and Adjustment .....................................................A6

Video Memory Modes ...........................................A8

Troubleshooting .....................................................A9

Specifications .......................................................A10

DEUTSCH

Einleitung ................................................................B1

Anschließen ............................................................B2

Ort und Funktion der Bedienungselemente ..........B3

Bedienungselemente der Bildkontrolle..................B4

On Screen Display (OSD) Anpassung ...................B5

OSD Einstellung und Auswahlsymbole .................B6

Videospeichermodi ................................................B8

Störungen................................................................B9

Produktbeschreibung ...........................................B10

FRANÇAIS

Introduction ...........................................................C1

Branchement du Moniteur ....................................C2

Nomenclature et Fonctions ...................................C3

Fonctions du Paneau de Commande.....................C4

Réglage des Commandes Affichage Écran.............C5

Options de sélection et de Réglage

OSD (affichage écran) ..........................................C6

Mise en Mémoire de Modes Vidéo........................C8

Quelques Conseils en Cas D’incident....................C9

Spécifications D'entree........................................C10

ITALIANO

Introduzione ..........................................................D1

Collegamento del Monitor ....................................D2

Posizione e Funzione dei Conando di Controllo ..D3

Funzione del Pannello di Controllo.......................D4

Controllo Regolazione On Screen Display (OSD)....D5

Elementi di Selezione e Regolazione dell'OSD.....D6

Modalità di Memoria Video ..................................D8

In Caso di Problemi ...............................................D9

Specifiche.............................................................D10

ESPAÑOL

Introducción ...........................................................E1

Conectando del Monitor ........................................E2

Ubicacion y Funcion de los Controles ...................E3

Función del Panel de Control.................................E4

Ajuste del Control de Exhibición en Pantalla (OSD) .......E5

Ajuste del OSD y Selección de Elementos .............E6

Modos de Memoria de Video.................................E8

Sugerencias para Localizar las Fallas......................E9

Especificaciones ....................................................E10

PORTUGUÊS

Introdução...............................................................F1

Conectando o Monitor ...........................................F2

Posição dos Controles e Descrição ........................F3

Funções do Painel de Controle ..............................F4

Ajuste On Screen Display(OSD) ............................F5

Ajustes OSD e Itens de Seleção .............................F6

Modos de Memória de Vídeo.................................F8

Resolvendo Problemas............................................F9

Especificações .......................................................F10

NEDERLANDS

Inleiding .................................................................N1

De Monitor Aansluiten..........................................N2

De plaatsing en de werking van de knoppen........N3

Het bedieningspaneel ............................................N4

Bediening via het beeldscherm OSD

(On Screen Display) ..............................................N5

Kiezen en instellen via het OSD-systeem..............N6

Modi voor videogeheugen.....................................N8

Problemen oplossen...............................................N9

Specificaties .........................................................N10

Introduction

The FLATRON LCD 680LE Flat Panel Monitor has an active matrix TFT

(Thin-Film Transistor) LCD (Liquid Crystal Display).

This monitor is designed for use in small working areas or for those who need more working space on the desk.

Features

The FLATRON LCD 680LE is a 15.7-inch (15.7 inches viewable) intelligent microprocessor based monitor.

Digitally controlled auto-scanning is done with the micro-processor for horizontal scan frequencies between 30 and 80kHz, and vertical scan frequencies between 56 - 85Hz.

The microprocessor-based digital controls allow you to adjust conveniently a variety of image controls by using the OSD (On Screen Display).

It supports resolutions up to 1280x1024, and has a wide viewing angle of ±60 degrees horizontal and ±45 degrees vertical.

The monitor is shipped with 16 factory pre-programmed video modes that are permanently resident. In addition, there are 10 user-storable modes, for a total of 26 memory modes.

Plug and play capability if supported by your system.

This monitor has DDC 2B function.*

Compliant with the following regulated specifications :*

- EPA E

NERGY

S

TAR

- Swedish TCO’99

* For detailed information, please refer to the Reference Guide provided .

A1

133B

Connecting the Monitor

To set up the monitor, ensure that the power is turned off to the monitor, computer system, and other attached devices. Connect the cables to monitor with it lying on a cushion or a cloth.

Follow these steps:

1

Power off both the monitor and computer.

2 Connect one end of the monitor signal cable to the input connector on the rear panel of the monitor.

3 Connect the other end to the 15-pin connector on the real panel of the computer and tighter the screws. Be sure the signal cable aligns with the 15pin connector.

4 Connect the other end of the monitor signal cable to the rear panel of

Macintosh computer through a Macintosh adapter and then tighten screws.

4'

Connect one end of the AC power cord to the AC adapter 2 and the other end to a properly grounded AC outlet that is easily accessible and close to the

5 Power on the computer, then the monitor.

6 If you see the NO SIGNAL message, check the signal cable and connectors.

7 After using the system, power OFF the monitor, then the computer.

3

Power

Cord

IBM MACINTOSH

2 AC adapter

A2

D-15P 4

Adapter D-15P

Signal Cable

Note : If you see the “OUT OF RANGE” message, check to make sure your system is set to one of the factory preset modes

(see page A8), or is set to a resolution and refresh rate within the specification limits of this monitor.

4'

Location and Function of Controls

Front View

Rear View

OSD Button AUTO/SET Button

Buttons

Power Button

Power Indicator

DC Power Connecter

+

A3

D-Sub Signal Connector

Control Panel Function

Front Panel Controls

OSD Button AUTO/SET Button Power Button

Control

OSD Button

100

Button

100

AUTO/SET Button

P R O C E S S I N G

A U T O C O N F I G U R A T I O N

Power Button

Power Indicator

Button Power Indicator

Function

Use this button to enter or exit the on screen display.

Use these buttons to choose or adjust items in the on screen display.

<Shortcut Keys>

• Brightness and Contrast can be adjusted directly without entering the On Screen Display (OSD) system.

Touch the buttons to adjust the settings and then the OSD button to save all changes. The

Brightness and Contrast functions are also available in the On Screen Display (OSD) menu.

Use this button to enter a selection in the on screen display.

* AUTO adjustment function

Touch the AUTO/SET button before using OSD menu.

This button is for the automatic adjustment of the screen position, clock and phase.

Note: Some signal from some graphics boards may not function properly. If the results are unsatisfactory, adjust your monitor’s

Position, Clock and Phase manually.

Use this button to turn the monitor on or off.

The power indicator light is shown in the power button.

This indicator lights up green when the monitor operates normally. If the monitor is in DPM (Energy

Saving) mode (stand-by/ suspend/power off), this indicator color changes to amber.

A4

On Screen Display (OSD) Control Adjustment

Making adjustments to the image size, position and operating parameters of the monitor are quick and easy with the On Screen Display Control system.

A quick example is given below to familiarize you with the use of the controls.

Following section is an outline of the available adjustments and selections you can make using the OSD.

NOTE

Allow the monitor to stabilize for at least 30 minutes before making image adjustment.

To make adjustments in the On Screen Display, follow these steps:

Press the OSD Button, then the main menu of the OSD appears.

2

2

3

3

To acces a control, use the or Buttons. When the icon you want becomes highlighted, press the AUTO/SET Button.

Use the Buttons to adjust the item to the desired level.

Accept the changes by pressing the AUTO/SET Button.

Exit the OSD by Pressing the OSD Button.

A5

On Screen Display(OSD) Selection and Adjustment

You were introduced to the procedure of selection and adjusting an item using the OSD system.

Listed below are the icons, icon names, and icon descriptions of the items that are shown on the Menu.

OSD Adjust

BRIGHTNESS CONTRAST

88

100

Description

Brightness

Used to adjust the brightness of the screen.

Contrast

Adjust the display to the contrast desired.

COLOR

PRESET

9300K 6500K

RED

GREEN

BLUE

PRESET 9300K/ 6500K

To appear the displays color temperature.

• 9300K:Slightly bluish white.

• 6500K:Slightly reddish white.

RED To set your own color levels.

GREEN To set your own color levels.

BLUE To set your own color levels.

POSITION

61

39

Vertical Position

To move image up and down.

Horizontal Position

To move picture image left and right.

A6

On Screen Display(OSD) Selection and Adjustment

OSD Adjust

CLOCK

PHASE

TRACKING

CLOCK

PHASE

Description

To minimize any vertical bars or stripes visible on the screen background.The horizontal screen size will also change.

To adjust the focus of the display.

This item allows you to remove any horizontal noise and clear or sharpen the image of characters.

SETUP

LANGUAGE

IMAGE SIZE

OSD POSITION

MODE INFO

ENGLISH

FULL

ON

4 8 . 3 k H z / 6 0 . 0 H z

P R E S E T M O D E

LANGUAGE To choose the language in which the control names are displayed.

IMAGE SIZE This function displays the image in its original size or enlarged size so as to fit in the full screen of the LCD panel.

OSD POSITION To adjust position of the OSD window on the screen.

MODE INFO This function displays the current mode information on the screen when power on the monitor.

A7

Video Memory Modes

The monitor has 26 memory locations for display modes, 16 of which are factory preset to popular video modes.

Display Modes (Resolution)

13

14

15

16

9

10

11

12

7

8

5

6

3

4

1

2

Display Modes (Resolution)

VGA

VGA

VGA

VESA

VESA

VESA

VESA

VESA

MAC

VESA

VESA

VESA

VESA

VESA

VESA

VESA

640 x 350

720 x 400

640 x 480

640 x 480

640 x 480

800 x 600

800 x 600

800 x 600

832 x 624

1024 x 768

1024 x 768

1024 x 768

1152x870

1152x900

1280x1024

1280x1024

Horizontal Freq.(kHz)

49.73

48.36

60.12

68.67

68.68

61.80

63.98

79.98

31.47

31.47

31.47

37.50

43.27

37.88

46.88

53.67

Vertical Freq.(Hz)

75

66

60

75

75

60

75

85

85

60

75

85

70

70

60

75

Note : This LCD monitor has been pre-adjusted to the video mode of

VESA 1280x1024 @60Hz.

User Modes

Modes 17-26 are empty and can accept new video data. If the monitor detects a new video mode that has not been present before or is not one of the preset modes, it stores the new mode automatically in one of the empty modes starting with mode 17.

If you use up the 10 blank modes and still have more new video modes, the monitor replaces the information in the user modes starting with mode 17.

A8

Troubleshooting

Check the following before calling for service.

Display Position is incorrect.

Push the AUTO/SET Button.

If the results are unsatisfactory, adjust the image position using the H position and

V position icon in the on screen display.

On the screen background, vertical bars or stripes are visible.

Push the AUTO/SET Button.

If the results are unsatisfactory, decrease the vertical bars or stripes using the

CLOCK icon in the on screen display.

Any horizontal noise appearing in any image or characters are not clearly portraid.

Push the AUTO/SET Button.

If the results are unsatisfactory, decrease the horizontal bars using the PHASE icon in the on screen display.

NO SIGNAL message.

The signal cable is not connected, or is loose. Check and secure the connection.

OUT OF RANGE message appears.

Picture is blank.

The frequency of the signal from the video card is outside the operating range of the monitor.

Horizontal Frequency: 30kHz-80kHz

Vertical Frequency: 56Hz-85Hz

* Use the graphics board's utility software to change the frequency setting (Refer to the manual for graphics board).

* You can change the setup to the supported resolution using the Safe Mode (Press the F8 key during booting the system).

The power LED is illuminated amber.

The monitor is in its display power management mode.

There is no active signal coming from the PC.

The signal cable is not fastened securely.

Check the computer power and graphics adapter configuration.

The monitor doesn't enter the power saving off mode (Amber).

Computer video signal is not VESA DPMS standard. Either the PC or the video controller card is not using the VESA DPMS power management function.

NOTE

If the power indicator(LED) light is blinking amber, may result in abnomal condition of the monitor.

Then press a power ON/OFF button on the front panel control and call your service technician for more information.

A9

Specifications

Display

Sync Input

Video Input

Power

Consumption

Dimensions

Power Input

AC Adapter

Weight

Tilt Range

Environment

Conditions

Type

Viewable Size

Pixel pitch

True color

Horizontal Freq.

Vertical Freq.

Input form

Signal input

15.7inch (39.83cm) Flat Panel Active matrix-TFT LCD

Anti-Glare coating

15.7inch (39.83cm)

0.243 x 0.243mm

16.7 million color

30kHz - 80kHz (Automatic)

56Hz - 85Hz (Automatic)

Separate, TTL, Positive/Negative

15 pin D-Sub connector

Display Area

Input Form

311 x 248.8 mm / 12.2 x 9.79 inch

Separate, RGB Analog, 0.714Vp-p/75ohm,

Positive

Resolution (max.) VESA 1280 x 1024 @ 75Hz

Normal

≤ 36W

Stand-by/Suspend ≤ 3W

Power Off ≤ 3W

Width

Height

37.0 cm / 14.57 inches

38.77 cm / 15.26 inches

Depth 13.4 cm / 5.28 inches

DC 24V 1.2A

Input

Output

Net

Down

Up

AC 100-240V, 50 - 60Hz, 1.2A - 0.6A

DC 24V 1.5A

4.5 kg (9.92 lbs)

-5˚

35˚

+

Operating condition

Temperature

Humidity

Storage condition

Temperature

Humidity

10˚C to 35˚C

10% to 80% non-condensing

-20˚C to 60˚C

5% to 95% non-condensing

NOTE

Information in this document is subject to change without notice.

A10