Cover Important
Important
Please read PRECAUTIONS, this User’s Manual, and the Setup Guide
(separate volume) carefully to familiarize yourself with safe and
effective usage.
•Please refer to the Setup Guide for basic information ranging from
connection of the monitor to a PC to using the monitor.
•The latest User’s Manual is available for download from our web site:
http://www.eizo.com
Location of Caution Statement
EV2316W / EV2336W
EV2416W / EV2436W
This product has been adjusted specifically for use in the region to which it was originally shipped. If operated
outside this region, the product may not perform as stated in the specifications.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means,
electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.
EIZO Corporation is under no obligation to hold any submitted material or information confidential unless prior
arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every effort has been
made to ensure that this manual provides up-to-date information, please note that EIZO monitor specifications are
subject to change without notice.
2

Notice for this monitor
This product is suited to general purposes like creating documents, viewing multimedia content.
This product has been adjusted specifically for use in the region to which it was originally shipped. If the product is
used outside the region, it may not operate as specified in the specifications.
This product may not be covered by warranty for uses other than those described in this manual.
The specifications noted in this manual are only applicable when the following are used:
· Power cords provided with the product
· Signal cables specified by us
Only use optional products manufactured or specified by us with this product.
It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more after the
monitor power has been turned on, and then adjust the monitor.
Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term use and maintain a
stable display.
When the screen image is changed after displaying the same image for extended periods of time, an afterimage may
appear. Use the screen saver or power save function to avoid displaying the same image for extended periods of time.
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime (refer to
“Cleaning” (page 4)).
The LCD panel is manufactured using high-precision technology. Although, missing pixels or lit pixels may appear on
the LCD panel, this is not a malfunction. Percentage of effective dots: 99.9994% or higher.
The backlight of the LCD panel has a fixed lifetime. When the screen becomes dark or begins to flicker, please contact
your local EIZO representative.
Do not press on the panel or edge of the frame strongly, as this may result in display malfunctions, such as interference
patterns, etc. If pressure is continually applied to the panel, it may deteriorate or damage your panel. (If the pressure
marks remain on the panel, leave the monitor with a black or white screen. The symptom may disappear.)
Do not scratch or press on the panel with any sharp objects, as this may result in damage to the panel. Do not attempt
to brush with tissues as this may scratch the panel.
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew condensation may
occur on the interior and exterior surfaces of the monitor. In that case, do not turn the monitor on. Instead wait until
the dew condensation disappears, otherwise it may cause some damage to the monitor.
Notice for this monitor
3
Cleaning
Attention
• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet or panel,
and also quality deterioration of the image.
• Never use any thinner, benzene, wax, and abrasive cleaner, which may damage the cabinet or panel.
Note
• The optional ScreenCleaner is recommended for cleaning the cabinet and panel surface.
If necessary, the stains on the cabinet and panel surface can be removed by moistening part of a soft cloth with
water.
To use the monitor comfortably
• An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor according to
the environmental conditions.
• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.
4
Notice for this monitor
CONTENTS
Cover....................................................................... 1
Chapter 3 Setting Monitor................................ 31
Notice for this monitor.......................................... 3
3-1.
Adjusting Volume.........................................31
Cleaning..................................................................... 4
3-2.
Selecting sound source while using the
DisplayPort signal input..............................31
3-3.
Compensating viewing angle deficiency
(EV2316W / EV2416W only)......................... 32
3-4.
Enabling / Disabling DDC/CI
communication ........................................... 32
3-5.
Locking Operation Buttons........................ 33
3-6.
Setting Orientation...................................... 33
3-7.
Showing and hiding the EIZO logo............ 33
3-8.
Changing Setting Menu Display Position. 34
3-9.
Setting Language......................................... 34
To use the monitor comfortably.............................. 4
CONTENTS.............................................................. 5
Chapter 1 Introduction........................................ 7
1-1.
1-2.
Features.......................................................... 7
Controls and Functions................................ 9
●●
●●
Front................................................................. 9
Rear.................................................................10
1-3.
EIZO LCD Utility Disk...................................11
●●Disk contents and software overview.............11
●●To use “ScreenManager Pro for LCD
(DDC/CI) / EIZO ScreenSlicer”.......................11
1-4.
Basic Operations and Functions................12
●●
●●
Basic operation of the Setting menu...............12
Functions.........................................................13
Chapter 2 Adjusting Screens........................... 14
2-1.
Compatible Resolutions..............................14
●●EV2316W........................................................14
●●EV2336W........................................................15
●●EV2416W.........................................................16
●●EV2436W........................................................17
2-2.
Setting the Resolution.................................18
●●Windows 8 / Windows 7..................................18
●●Windows Vista.................................................18
●●Windows XP....................................................18
●●Mac OS X........................................................18
2-3.
Adjusting Color.............................................19
●●To select the display mode
(FineContrast Mode).......................................19
To perform advanced adjustments................ 20
Adjustable settings in each mode.................. 20
To adjust brightness....................................... 20
To adjust contrast............................................21
To adjust color temperature............................21
To adjust gamma . ......................................... 22
To adjust the color saturation......................... 22
To adjust hue.................................................. 23
To set overdrive intensity (EV2336W /
EV2436W only).............................................. 23
To adjust gain..................................................24
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
2-4.
Screen Adjustment...................................... 25
●●
●●
Digital Signal Input......................................... 25
Analog Signal Input........................................ 25
2-5.
Screen Size Changing................................. 29
●●Screen Size Changing................................... 29
●●To adjust brightness of non-display area....... 30
3-10. Resetting the Monitor to the Default
Settings......................................................... 35
●●To reset the color adjustments....................... 35
●●To reset “EcoView Sense Settings”............... 35
●●To reset all adjustments to the default
settings........................................................... 35
Chapter 4 Power Saving Functions................. 36
4-1.
Setting Power Saving.................................. 36
●●
●●
Monitor........................................................... 36
Audio Output...................................................37
4-2.
Setting Power Indicator................................37
4-3.
Enabling / Disabling Automatic
Brightness Adjustment ...............................37
●●Auto EcoView..................................................37
●●EcoView Optimizer 2...................................... 38
4-4.
Setting the power saving mode when a
person leaves the monitor.......................... 38
4-5.
Checking the power saving level............... 40
4-6.
Enabling / Disabling Auto Power-OFF....... 40
Chapter 5 Troubleshooting............................... 41
5-1.
No picture......................................................41
5-2.
Imaging problems (for both digital and
analog)........................................................... 42
5-3.
Imaging problems (for digital only)........... 43
5-4.
Imaging problems (for analog only).......... 43
5-5.
Other problems............................................ 44
Chapter 6 Reference......................................... 46
6-1.
Attaching the Optional Arm........................ 46
6-2.
Detaching/Attaching Stand Base................47
6-3.
Attaching/Detaching Cable Holder............ 49
6-4.
Connecting Multiple PCs.............................51
●●
●●
To switch among input signals........................51
To set input signal selection............................52
CONTENTS
5
6-5.
Making Use of USB (Universal Serial
Bus)................................................................ 52
●●Required System Environment.......................52
●●Connection Procedure (Setup of USB
Function)......................................................... 53
6-6.
Displaying Monitor Information................. 53
6-7.
Specifications.............................................. 54
6-8.
Preset Timing............................................... 62
6-9.
Glossary........................................................ 64
●●EV2316W....................................................... 54
●●EV2336W....................................................... 55
●●EV2416W........................................................ 57
●●EV2436W....................................................... 58
●●Main Default Settings..................................... 60
●●Outside Dimensions....................................... 60
●●Accessories.....................................................61
●●EV2316W....................................................... 62
●●EV2336W....................................................... 62
●●EV2416W........................................................ 63
●●EV2436W....................................................... 63
Appendix............................................................... 66
Trademark................................................................ 66
License..................................................................... 66
ENERGY STAR......................................................... 67
TCO........................................................................... 67
FCC Declaration of Conformity............................. 68
Hinweise zur Auswahl des richtigen
Schwenkarms für Ihren Monitor............................ 69
Hinweis zur Ergonomie :........................................ 69
LIMITED WARRANTY...............................................70
Recycling Information............................................ 79
China Measures for RoHS Compliance in
ChinaRoHS............................................................... 83
6
CONTENTS
Chapter 1 Introduction
Thank you very much for choosing an EIZO color LCD monitor.
1-1. Features
• 23.0″ wide format LCD (EV2316W / EV2336W)
• 24.1″ wide format LCD (EV2416W / EV2436W)
• Supports a resolution of 1920 × 1080 (EV2316W / EV2336W)
• Supports a resolution of 1920 × 1200 (EV2416W / EV2436W)
• IPS panel with 89˚ horizontal and vertical viewing angles (EV2336W / EV2436W only)
• Applicable to DisplayPort (applicable to 8 bit)*1
The DisplayPort input receives both an image signal and an audio signal via a single DisplayPort cable.
*1 When transmitting an audio signal using the DisplayPort cable, the graphics board must be compatible with audio
output (see “6-7. Specifications” (page 54)).
• The FineContrast function allows the user to select the display mode optimum to the displayed image.
-- The Paper mode reproduces a printed paper effect on the monitor.
See “To select the display mode (FineContrast Mode)” (page 19).
• The software “ScreenManager Pro for LCD (DDC/CI)” to adjust the screen using the mouse and keyboard is
included
See “1-3. EIZO LCD Utility Disk” (page 11).
-- EyeCare Filter
Texture of the paper is reproduced by displaying a translucent image in the foreground of the desktop.
By using this function with the Paper mode, the screen looks more like paper.
See “To select the display mode (FineContrast Mode)” (page 19).
• Supports the power management software “EIZO EcoView NET”
For more information, refer to our web site (http://www.eizo.com).
• Power saving function
Suppressing the power consumption*2 reduces the carbon dioxide emissions. This product is equipped with power saving
function.
-- 0 W power consumption when the main power is off
Equipped with main power switch.
When the monitor is not required, the power supply can be shut off using the main power switch.
-- Auto EcoView
The ambient light sensor on the front side of the monitor detects the environmental brightness to adjust the screen
brightness automatically and comfortably. Excessively high brightness may increase power consumption and cause
unwanted environmental effects. It may also lead to fatigue of your eyes. Use the Auto EcoView to reduce the
brightness.
See “Auto EcoView” (page 37).
-- EcoView Optimizer 2
The monitor automatically adjusts the screen brightness according to the white level of the input signal. This
function can reduce the power consumption while maintaining the brightness specified by the input signal.
See “EcoView Optimizer 2” (page 38).
-- EcoView Sense
The sensor on the front side of the monitor detects the movement of a person. When a person moves away from the
monitor, the monitor shifts to the power saving mode automatically and does not display the images on the screen.
Therefore, the function reduces the power consumption. The sensitivity and time until the power saving mode is
activated can be set according to the monitor usage environment and movement of the user.
See “4-4. Setting the power saving mode when a person leaves the monitor” (page 38).
Chapter 1 Introduction
7
*2 Reference values:
EV2316W
Maximum power consumption: 43 W (Brightness Max., when a USB device is connected, speaker working, at
default settings)
Standard power consumption: 14 W (Brightness 120 cd/m 2, when no USB device is connected, speaker not working,
at default settings)
EV2336W
Maximum power consumption: 40 W (Brightness Max., when a USB device is connected, speaker working, at
default settings)
Standard power consumption: 14 W (100VAC, Brightness 120 cd/m 2, when no USB device is connected, speaker not
working, at default settings)
Standard power consumption: 15 W (200VAC, Brightness 120 cd/m 2, when no USB device is connected, speaker not
working, at default settings)
EV2416W
Maximum power consumption: 40 W (Brightness Max., when a USB device is connected, speaker working, at
default settings)
Standard power consumption: 11 W (Brightness 120 cd/m 2, when no USB device is connected, speaker not working,
at default settings)
EV2436W
Maximum power consumption: 60 W (Brightness Max., when a USB device is connected, speaker working, at
default settings)
Standard power consumption: 19 W (Brightness 120 cd/m 2, when no USB device is connected, speaker not working,
at default settings)
• Up View (EV2316W / EV2416W only)
The viewing angle is adjusted so that the screen looks like a front view when the screen is looked up.
See “3-3. Compensating viewing angle deficiency (EV2316W / EV2416W only)” (page 32).
• Supports portrait and landscape formats
• Displays HDCP (High-bandwidth Digital Protection) protected contents.
Note
• This monitor supports the portrait display. This function allows you to change the orientation of the Setting menu when
using the monitor screen in vertical display position (see “3-6. Setting Orientation” (page 33)).
• When using the monitor screen in a portrait position, the graphics board supporting portrait display is required. When
placing the monitor in a portrait position, the settings of your graphics board need to be changed. Refer to the User’s
Manual of the graphics board for details.
8
Chapter 1 Introduction
1-2. Controls and Functions
●●Front
Setting menu*1
1
1. EcoView Sense sensor
2
3
4
5
6
7
8
9
Detects the movement of a person in front of the monitor (EcoView Sense function (page
38)).
2. Ambient light sensor
Detects ambient brightness (Auto EcoView function (page 37)).
3.
Displays the setting menu of the power saving function (Auto EcoView (page 37) and
EcoView Optimizer 2 (page 38)) and EcoView Sense (page 38).
button
4.
button
Switches input signals for display (page 51).
5.
button
Changes the FineContrast mode (page 19).
6.
button
Displays the Setting menu, determines an item on the menu screen, and saves values
adjusted (page 12).
7.
,
8.
button
button*2
• Provides the menu selection as well as the adjustment and setting of a function.
•
button: Displays the volume adjustment menu (page 31).
button: Displays the Brightness adjustment menu (page 20).
Turns the power on or off.
Indicates the monitor’s operation status.
9. Power indicator
Blue:
Operating
Orange:
Power saving mode
OFF:
Main power / Power off
*1 See “1-4. Basic Operations and Functions” (page 12) for how to use.
button may be hereafter simply displayed as
*2 In this User’s Manual, the
, and the
button as
.
Chapter 1 Introduction
9
●●Rear
15
13
16
17
18
19
20
14
21
1011
*3
12
10. Main power switch
Turns the main power on or off.
11. Power connector
Connects the power cord.
12. Input signal connector
Left: DisplayPort connector / Center: DVI-D connector / Right: D-Sub mini15-pin
connector
13. Security lock slot
Complies with Kensington’s MicroSaver security system.
14. Speaker
Outputs audio source.
Handle used for transportation
15. Handle
Attention
• Firmly grasp and hold the monitor by the bottom while grabbing the handle, and carefully
convey the monitor so as not to drop it.
16. Stand*4
Adjusts the height and angle (tilt and swivel) of the monitor.
17. USB port (DOWN)
Connects a peripheral USB device.
18. USB port (UP)
Connects the USB cable for using the USB Hub function (page 52).
19. Headphone jack
Connects the headphones.
20. Stereo mini jack
Connects the stereo mini jack cable (commercially available product).
21. Cable holder
Covers the monitor cables.
*3 See “6-3. Attaching/Detaching Cable Holder” (page 49) for how to attach the cable holder.
*4 An optional arm (or an optional stand) can be attached by removing the stand (see “6-1. Attaching the Optional Arm” (page 46)).
10
Chapter 1 Introduction
1-3. EIZO LCD Utility Disk
An “EIZO LCD Utility Disk” (CD-ROM) is supplied with this product. The following table shows the disk contents
and the overview of the software programs.
●●Disk contents and software overview
The disk includes software programs for adjustment, and User’s Manual. Refer to Readme.txt file on the disk
for software startup procedures or file access procedures.
Item
Overview
Windows
Macintosh
Screen adjustment pattern files
Used when adjusting the image of analog
signal input manually.
√
√
ScreenManager Pro for LCD
(DDC/CI)
Software for adjusting the screen using the
mouse and keyboard.
√
-
EIZO ScreenSlicer
Software that divides a screen and lays out
multiple windows efficiently.
√
-
User’s Manual of this monitor (PDF file)
√
√
Readme.txt file
√
√
●●To use “ScreenManager Pro for LCD (DDC/CI) / EIZO ScreenSlicer”
For the installation and use of “ScreenManager Pro for LCD (DDC/CI) / EIZO SceenSlicer”, refer to the
respective User’s Manual on the disk.
Chapter 1 Introduction
11
1-4. Basic Operations and Functions
●●Basic operation of the Setting menu
1.Displaying the Setting menu
1. Press
. The Setting menu appears.
2.Adjusting / Setting
1. Choose a menu to adjust / set with , , and then press
. The Sub menu appears.
2. Choose an item to adjust / set with , , and then press
. The adjustment / setting menu appears.
3. Adjust / set the selected item with , , and then press
3.Exiting
1. Choose “Return” from the Sub menu and press
2. Choose “Exit” from the Main menu and press
.
. The Setting menu appears.
. The Setting menu quits.
Note
• The Setting menu can also be exited by pressing
12
Chapter 1 Introduction
twice quickly.
●●Functions
The following table shows the Setting menu and setting items of each menu.
Main menu
Color*1
Screen
Sound
Setting
Brightness
Contrast
Temperature
Gamma
Advanced Settings
Reference
“2-3. Adjusting Color” (page 19)
Saturation
Hue
Overdrive*2
Gain
Color Reset
Screen Size
Smoothing
Analog Adjustment*3 Auto Screen Adjust
Auto Range Adjust
Clock
Phase
Hor.Position
Ver.Position
Source
“To reset the color adjustments” (page 35)
“Screen Size Changing” (page 29)
“2-4. Screen Adjustment” (page 25)
“3-2. Selecting sound source while using
the DisplayPort signal input” (page 31)
Power Save
“Audio Output” (page 37)
PowerManager
Power Save
“4-1. Setting Power Saving” (page 36)
Eco Timer
“4-6. Enabling / Disabling Auto PowerOFF” (page 40)
Monitor Settings
Up View*4
“3-3. Compensating viewing angle
deficiency (EV2316W / EV2416W only)”
(page 32)
Input Signal
“To set input signal selection” (page 52)
Power Indicator
“4-2. Setting Power Indicator” (page 37)
Language
“3-9. Setting Language” (page 34)
DDC/CI
“3-4. Enabling / Disabling DDC/CI
communication” (page 32)
Border Intensity
“To adjust brightness of non-display area”
(page 30)
Menu Settings
Orientation
“3-6. Setting Orientation” (page 33)
Logo
“3-7. Showing and hiding the EIZO logo”
(page 33)
“3-8. Changing Setting Menu Display
Menu Position
Position” (page 34)
Reset
“To reset all adjustments to the default
settings” (page 35)
Information
“6-6. Displaying Monitor Information”
(page 53)
*1 The adjustment / settings available on the “Color” menu depend on the selected Color mode. The above table shows
the sub menus when the User1 or User2 mode is selected.
*2 EV2336W / EV2436W only
*3 These functions can be adjusted with analog input.
*4 EV2316W / EV2416W only
Chapter 1 Introduction
13
Chapter 2 Adjusting Screens
2-1. Compatible Resolutions
The monitor supports the following resolutions.
●●EV2316W
Analog Input (D-Sub)
Resolution
Applicable Signals
640 × 480
800 × 600
1024 × 768
1280 × 720
1280 × 960
1280 × 1024
1680 × 1050
1920 × 1080*1
VGA
VESA
VESA
CEA-861
VESA
VESA
VESA CVT, VESA CVT RB
CEA-861
Vertical Scan
Frequency
Dot Clock
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
148.5 MHz
(Max.)
Vertical Scan
Frequency
Dot Clock
Digital Input (DVI-D)
Resolution
Applicable Signals
640 × 480
800 × 600
1024 × 768
1280 × 720
1280 × 960
1280 × 1024
1680 × 1050
1920 × 1080*1
VGA
VESA
VESA
CEA-861
VESA
VESA
VESA CVT, VESA CVT RB
CEA-861
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
148.5 MHz
(Max.)
Vertical Scan
Frequency
Dot Clock
Digital Input (DisplayPort)
Resolution
Applicable Signals
640 × 480
720 × 480 (4:3)
720 × 480 (16:9)
800 × 600
1024 × 768
1280 × 720
1280 × 960
1280 × 1024
1680 × 1050
1920 × 1080*1
VGA, CEA-861
CEA-861
CEA-861
VESA
VESA
CEA-861
VESA
VESA
VESA CVT, VESA CVT RB
CEA-861
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
The graphics board should comply with the VESA standard and CEA-861 standard.
*1 Recommended resolution
14
Chapter 2 Adjusting Screens
148.5 MHz
(Max.)
●●EV2336W
Analog Input (D-Sub)
Resolution
Applicable Signals
640 × 480
720 × 400
800 × 600
1024 × 768
1280 × 720
1280 × 960
1280 × 1024
1680 × 1050
1920 × 1080*1
VGA, VESA
VGA TEXT
VESA
VESA
CEA-861
VESA
VESA
VESA CVT, VESA CVT RB
CEA-861
Vertical Scan
Frequency
Dot Clock
~75 Hz
70 Hz
~75 Hz
~75 Hz
60 Hz
60 Hz
~75 Hz
60 Hz
60 Hz
148.5 MHz
(Max.)
Vertical Scan
Frequency
Dot Clock
Digital Input (DVI-D)
Resolution
Applicable Signals
640 × 480
720 × 400
800 × 600
1024 × 768
1280 × 720
1280 × 960
1280 × 1024
1680 × 1050
1920 × 1080*1
VGA
VGA TEXT
VESA
VESA
CEA-861
VESA
VESA
VESA CVT, VESA CVT RB
CEA-861
60 Hz
70 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
148.5 MHz
(Max.)
Vertical Scan
Frequency
Dot Clock
Digital Input (DisplayPort)
Resolution
Applicable Signals
640 × 480
720 × 400
720 × 480 (4:3)
720 × 480 (16:9)
800 × 600
1024 × 768
1280 × 720
1280 × 960
1280 × 1024
1680 × 1050
1920 × 1080*1
VGA, CEA-861
VGA TEXT
CEA-861
CEA-861
VESA
VESA
CEA-861
VESA
VESA
VESA CVT, VESA CVT RB
CEA-861
60 Hz
70 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
148.5 MHz
(Max.)
The graphics board should comply with the VESA standard and CEA-861 standard.
*1 Recommended resolution
Chapter 2 Adjusting Screens
15
●●EV2416W
Analog Input (D-Sub)
Resolution
Applicable Signals
640 × 480
800 × 600
1024 × 768
1280 × 720*1
1280 × 960
1280 × 1024
1600 × 1200
1680 × 1050
1920 × 1200*2
VGA
VESA
VESA
CEA-861
VESA
VESA
VESA
VESA CVT, VESA CVT RB
VESA CVT, VESA CVT RB
Vertical Scan
Frequency
Dot Clock
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
193.3 MHz
(Max.)
Vertical Scan
Frequency
Dot Clock
Digital Input (DVI-D)
Resolution
Applicable Signals
640 × 480
800 × 600
1024 × 768
1280 × 720*1
1280 × 960
1280 × 1024
1600 × 1200
1680 × 1050
1920 × 1200*2
VGA
VESA
VESA
CEA-861
VESA
VESA
VESA
VESA CVT, VESA CVT RB
VESA CVT RB
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
162 MHz
(Max.)
Vertical Scan
Frequency
Dot Clock
Digital Input (DisplayPort)
Resolution
Applicable Signals
640 × 480
720 × 480 (4:3)
720 × 480 (16:9)
800 × 600
1024 × 768
1280 × 720*1
1280 × 960
1280 × 1024
1600 × 1200
1680 × 1050
1920 × 1200*2
VGA, CEA-861
CEA-861
CEA-861
VESA
VESA
CEA-861
VESA
VESA
VESA
VESA CVT, VESA CVT RB
VESA CVT RB
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
162 MHz
(Max.)
The graphics board should comply with the VESA standard and CEA-861 standard.
*1 For this resolution, the “Screen Size” setting is “Full Screen” (see “2-5. Screen Size Changing” (page 29)).
*2 Recommended resolution
16
Chapter 2 Adjusting Screens
●●EV2436W
Analog Input (D-Sub)
Resolution
Applicable Signals
640 × 480
720 × 400
800 × 600
1024 × 768
1280 × 720
1280 × 960
1280 × 1024
1600 × 1200
1680 × 1050
1920 × 1200*1
VGA, VESA
VGA TEXT
VESA
VESA
CEA-861
VESA
VESA
VESA
VESA CVT, VESA CVT RB
VESA CVT, VESA CVT RB
Vertical Scan
Frequency
Dot Clock
~75 Hz
70 Hz
~75 Hz
~75 Hz
60 Hz
60 Hz
~75 Hz
60 Hz
60 Hz
60 Hz
193.3 MHz
(Max.)
Vertical Scan
Frequency
Dot Clock
Digital Input (DVI-D)
Resolution
Applicable Signals
640 × 480
720 × 400
800 × 600
1024 × 768
1280 × 720
1280 × 960
1280 × 1024
1600 × 1200
1680 × 1050
1920 × 1200*1
VGA
VGA TEXT
VESA
VESA
CEA-861
VESA
VESA
VESA
VESA CVT, VESA CVT RB
VESA CVT RB
60 Hz
70 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
162 MHz
(Max.)
Vertical Scan
Frequency
Dot Clock
Digital Input (DisplayPort)
Resolution
Applicable Signals
640 × 480
720 × 400
720 × 480 (4:3)
720 × 480 (16:9)
800 × 600
1024 × 768
1280 × 720
1280 × 960
1280 × 1024
1600 × 1200
1680 × 1050
1920 × 1200*1
VGA, CEA-861
VGA TEXT
CEA-861
CEA-861
VESA
VESA
CEA-861
VESA
VESA
VESA
VESA CVT, VESA CVT RB
VESA CVT RB
60 Hz
70 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
162 MHz
(Max.)
The graphics board should comply with the VESA standard and CEA-861 standard.
*1 Recommended resolution
Chapter 2 Adjusting Screens
17
2-2. Setting the Resolution
When you connect the monitor to the PC and find that the resolution is improper, or when you want to change the
resolution, follow the procedure below.
●●Windows 8 / Windows 7
1. For Windows 8, click the “Desktop” tile on the Start Screen to display the desktop.
2. Right-click the mouse anywhere on the desktop except for icons.
3. From the displayed menu, click “Screen resolution”.
4. On the “Screen Resolution” dialog box, select the monitor.
5. Click “Resolution” to select the desired resolution.
6. Click the “OK” button.
7. When a confirmation dialog box is displayed, click “Keep changes”.
●●Windows Vista
1. Right-click the mouse anywhere on the desktop except for icons.
2. From the displayed menu, click “Personalize”.
3. On the “Personalization” window, click “Display Settings”.
4. On the “Display Settings” dialog box, select the “Monitor” tab and select desired resolution in the
“Resolution” field.
5. Click the “OK” button.
6. When a confirmation dialog box is displayed, click “Yes”.
●●Windows XP
1. Right-click the mouse anywhere on the desktop except for icons.
2. From the displayed menu, click “Properties”.
3. When the “Display Properties” dialog box is displayed, click the “Settings” tab and select desired resolution
for “Screen resolution” under “Display”.
4. Click the “OK” button to close the dialog box.
●●Mac OS X
1. Select “System Preferences” from the Apple menu.
2. When the “System Preferences” dialog box is displayed, click “Displays” for “Hardware”.
3. On the displayed dialog box, select the “Display” tab and select desired resolution in the “Resolutions” field.
4. Your selection will be reflected immediately. When you are satisfied with the selected resolution, close the
window.
18
Chapter 2 Adjusting Screens
2-3. Adjusting Color
●●To select the display mode (FineContrast Mode)
This function allows easy selection of a desired mode according to monitor application.
Display Modes
Mode
Purpose
User1
Select this to define a desired set of parameter settings.
User2
sRGB
Suitable for color matching with sRGB compatible peripherals.
Paper
Produces a printed paper effect. Suitable for displaying images from media such as books
and documents.
Movie
Suitable for playing back animated images.
The mode menu
appears.
Procedure
1. Press
.
The mode menu appears at the bottom left of the screen.
2. The mode among the list is highlighted in turn each time
You can switch the mode with
or
is pressed.
while the mode menu is displayed.
→User1←→User2←→sRGB←→Paper←→Movie←
Note
• The Setting menu and the Mode menu cannot be displayed at the same time.
• “ScreenManager Pro for LCD (DDC/CI)” allows you to select the FineContrast mode automatically according to the
application used (see “Chapter 3 Auto FineContrast” in the “ScreenManager Pro for LCD (DDC/CI)” User’s Manual).
Chapter 2 Adjusting Screens
19
●●To perform advanced adjustments
The “Color” menu of the Setting menu allows you to set and save the independent color adjustment for each
mode.
Attention
• It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more after the
monitor power has been turned on, and then adjust the monitor.
• Perform the range adjustment first when adjusting color for analog signals (see “To adjust color gradation automatically”
(page 28)).
• The same image may be seen in different colors on multiple monitors due to their monitor-specific characteristics. Make
fine color adjustment visually when matching colors on multiple monitors.
Note
• Using the “ScreenManager Pro for LCD (DDC/CI)” allows you to perform the color adjustment by using the mouse and
keyboard of your PC. (Refer to “Chapter 4 Color Adjustment” in the User’s Manual for “ScreenManager Pro for LCD
(DDC/CI)”.)
●●Adjustable settings in each mode
The adjustable settings depend on the mode. (Non-adjustable or non-settable function cannot be selected.)
√: Adjustable -: Not adjustable
FineContrast Mode
Function
User1
User2
sRGB
Paper
Movie
Brightness
√
√
√
√
√
Contrast
√
√
-
-
√
Temperature
√
√
-
√
√
Gamma
√
√
-
-
-
Saturation
√
√
-
-
√
Hue
√
√
-
-
√
Overdrive
√
√
-
-
-
Gain
√
√
-
-
-
√
√
√
√
√
Advanced Settings
*1
Color Reset
*1 EV2336W / EV2436W only
●●To adjust brightness
The screen brightness is adjusted by changing the brightness of the backlight (light source from the LCD back
panel).
Adjustable range
0 to 100
Procedure
.
1. Press
2. Use
3. Press
or
for adjustment.
to exit.
Note
• If you feel that the image is too dark even if the brightness is set to 100, adjust the contrast.
• Alternatively, you can use “Brightness” under “Color” in the Adjustment menu to adjust it.
• To adjust the screen brightness automatically and comfortably, see “4-3. Enabling / Disabling Automatic Brightness
Adjustment” (page 37).
20
Chapter 2 Adjusting Screens
●●To adjust contrast
The brightness of the screen is adjusted by varying the video signal level.
Adjustable range
0 to 100
Procedure
1. Choose “Color” in the Setting menu, and press
.
.
2. Choose “Contrast” in the “Color” menu, and press
The “Contrast” menu appears.
3. Use
or
for adjustment.
to exit.
4. Press
Note
• In the contrast of 50, every color gradation is displayed.
• When adjusting the monitor, it is recommended to perform the brightness adjustment which may not lose the gradation
characteristics, prior to the contrast adjustment.
• Perform the contrast adjustment in the following cases.
- When you feel the image is too dark even if the brightness is set to 100 (Set the contrast to higher than 50.)
●●To adjust color temperature
Color temperature can be adjusted.
The color temperature is normally used to express the hue of “White” and / or “Black” by a numerical value.
The value is expressed in degrees “K” (Kelvin).
The screen becomes reddish at a low color temperature, and bluish at a high color temperature, like the flame
temperature. A gain preset value is set for each color temperature setting value.
Adjustable range
Off, 4000 K-10000 K (specified by every 500 K unit, including 9300 K)
Procedure
1. Choose “Color” in the Setting menu, and press
2. Choose “Temperature” in the “Color” menu, and press
.
.
The “Temperature” menu appears.
3. Use
4. Press
or
for adjustment.
to exit.
Note
• The value shown in “K” is available only as reference.
• “Gain” allows you to perform more advanced adjustment (see “To adjust gain” (page 24)).
• If you set to “Off”, the image is displayed in the preset color of the monitor (Gain: 100 for each RGB).
• When gain is changed, the color temperature is changed to “Off”.
Chapter 2 Adjusting Screens
21
●●To adjust gamma
Gamma can be adjusted. The brightness of the monitor varies depending on the input signal, however, the
variation rate is not proportional to the input signal. To keep the balance between the input signal and the
brightness of the monitor is called as “Gamma correction”.
Adjustable range
1.8, 2.0, 2.2
Procedure
1. Choose “Color” in the Setting menu, and press
.
.
2. Choose “Gamma” in the “Color” menu, and press
The “Gamma” menu appears.
3. Use
or
for adjustment.
to exit.
4. Press
Note
• If “Paper” is selected in the FineContrast mode, the gamma value is displayed for “Paper”. The setting “Paper” is
specially meant to get the displayed image look like it is printed on paper.
●●To adjust the color saturation
This function allows you to adjust color saturation.
Adjustable range
-50 to 50
Procedure
1. Choose “Color” in the Setting menu, and press
.
2. Choose “Advanced Settings” in the “Color” menu, and press
3. Choose “Saturation” in the “Advanced Settings” menu, and press
The “Saturation” menu appears.
4. Use
5. Press
or
for adjustment.
to exit.
Attention
• Using this function may make some color gradations unavailable for display.
Note
• The minimum value (-50) changes the screen to monochrome.
22
Chapter 2 Adjusting Screens
.
.
●●To adjust hue
This function allows you to adjust hue.
Adjustable range
-50 to 50
Procedure
1. Choose “Color” in the Setting menu, and press
.
.
2. Choose “Advanced Settings” in the “Color” menu, and press
3. Choose “Hue” in the “Advanced Settings” menu, and press
.
The “Hue” menu appears.
4. Use
or
for adjustment.
to exit.
5. Press
Attention
• Using this function may make some color gradations unavailable for display.
●●To set overdrive intensity (EV2336W / EV2436W only)
This function allows you to set overdrive intensity based on the use of the monitor. You can reduce Image lags
by setting it to “Enhanced” when displaying animated images.
Adjustable range
Enhanced, Standard, Off
Procedure
1. Choose “Color” in the Setting menu, and press
.
2. Choose “Advanced Settings” in the “Color” menu, and press
3. Choose “Overdrive” in the “Advanced Settings” menu, and press
.
.
The “Overdrive” menu appears.
4. Use
5. Press
or
for adjustment.
to exit.
Attention
• The overdrive function is disabled in the following cases:
- The vertical scan frequency of input signals is more than 60 Hz
- Select “Normal” during “Screen Size” (excluding the case that display resolution is 1920 × 1080 (EV2336W) or 1920
× 1200 (EV2436W)).
Chapter 2 Adjusting Screens
23
●●To adjust gain
The brightness of each color component red, green, and blue is called “Gain”. You can change the hue of
“white” by adjusting gain.
Adjustable range
0 to 100
Procedure
1. Choose “Color” in the Setting menu, and press
.
.
2. Choose “Advanced Settings” in the “Color” menu, and press
3. Choose “Gain” in the “Advanced Settings” menu, and press
.
The “Gain” menu appears.
4. Adjust gain with
5. Press
or
for each of red, green, and blue.
to exit.
Attention
• Using this function may make some color gradations unavailable for display.
Note
• The value of gain changes with that of color temperature.
• When gain is changed, the color temperature is changed to “Off”.
24
Chapter 2 Adjusting Screens
2-4. Screen Adjustment
●●Digital Signal Input
When digital signals are input, images are displayed correctly based on the preset data of the monitor, but if
characters and / or lines appear blurred, go to “To modify blurred characters / lines” (page 28).
When performing more advanced adjustment, see “2-3. Adjusting Color” (page 19) and subsequent pages.
●●Analog Signal Input
Attention
• It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more after the
monitor power has been turned on, and then adjust the monitor.
• The Self Adjust (automatic screen adjustment) function does not work for the images under the resolution of 800 × 600
(SVGA).
• The self adjustment (or automatic screen adjustment) function works correctly when an image is fully displayed over the
Windows or Macintosh display area. They do not work properly in the cases below:
- When an image is displayed only on a part of the screen (command prompt window, for example)
- When a black background (wallpaper, etc.) is in use
Also, these functions cannot work properly in some graphic boards.
The monitor screen adjustment is used to suppress flickering of the screen or adjust screen position and screen
size correctly according to the PC to be used.
Note
• The Self Adjust function works when all of the following conditions are satisfied:
- When a signal is input into the monitor for the first time or when a resolution or vertical / horizontal scan frequency
not used before is set
If the screen is not displayed correctly even after performing the Self Adjust operation, adjust the screen
according to the procedures on the following pages to use the monitor comfortably.
Setting Procedures
1.Perform the auto adjustment.
●●To adjust flickering, screen position, and screen size automatically
Procedure
1. Choose “Screen” in the Setting menu, and press
.
2. Choose “Analog Adjustment” in the “Screen” menu, and press
.
3. Choose “Auto Screen Adjust” in the “Analog Adjustment” menu, and press
4. Select “Yes” with
or , and press
.
.
Flickering, screen position, and screen size are corrected by the auto-adjustment function.
If the screen is not displayed correctly even after performing the auto adjustment, perform adjustments
according to the following procedure. If the screen is displayed correctly, go to “5. Adjusting color gradation.”
(page 28).
Chapter 2 Adjusting Screens
25
2.Prepare to use analog screen adjustment patterns.
Load the “EIZO LCD Utility Disk” to your PC, and then open the “Screen adjustment pattern files”.
Note
• For details and instructions on opening the “Screen adjustment pattern files”, refer to the Readme.txt file.
3.Perform the auto adjustment again with the analog screen adjustment pattern
displayed.
●●To adjust flickering, screen position, and screen size automatically
Procedure
1. Display Pattern 1 in full screen on the monitor using the “Screen adjustment pattern files”.
2. Choose “Screen” in the Setting menu, and press
.
.
3. Choose “Analog Adjustment” in the “Screen” menu, and press
4. Choose “Auto Screen Adjust” in the “Analog Adjustment” menu, and press
5. Select “Yes” with
or , and press
.
.
Flickering, screen position, and screen size are corrected by the auto-adjustment function.
If the screen is not displayed correctly even after performing the auto adjustment, perform adjustments
according to the following procedure. If the screen is displayed correctly, go to “5. Adjusting color gradation.”
(page 28).
4.Choose “Screen” from the Setting menu to perform advanced adjustments.
Adjust the clock, phase and position, in this order.
●●To eliminate vertical bars
Procedure
.
1. Choose “Analog Adjustment” in the “Screen” menu, and press
2. Choose “Clock” in the “Analog Adjustment” menu, and press
.
The “Clock” menu appears.
3. Adjust the clock with
Press
4. Press
or
or
to eliminate vertical bars.
slowly so as not to miss the adjustment point.
to exit.
When blurring, flickering or bars appear on the screen after adjustment, proceed to “To remove flickering or blurring ”.
26
Chapter 2 Adjusting Screens
●●To remove flickering or blurring
Procedure
.
1. Choose “Analog Adjustment” in the “Screen” menu, and press
2. Choose “Phase” in the “Analog Adjustment” menu, and press
.
The “Phase” menu appears.
3. Adjust the phase with
4. Press
or
to minimize flickering or blurring.
to exit.
When vertical bars appear on the screen after adjustment, go back to “To eliminate vertical bars ”.
(Clock → Phase → Position)
Attention
• Flickering or blurring may not be eliminated depending on your PC or graphics board.
●●To correct the screen position
Note
• Since the number of pixels and the pixel positions are fixed on the LCD monitor, only one position is provided to display
images correctly. The position adjustment is made to shift an image to the correct position.
Procedure
1. Choose “Analog Adjustment” in the “Screen” menu, and press
.
2. Choose “Hor.Position” or “Ver.Position” from the “Analog Adjustment” menu, and press
.
The “Hor. Position” or “Ver. Position” menu appears.
3. Adjust the position with
4. Press
or .
to exit.
5. Close Pattern 1.
Chapter 2 Adjusting Screens
27
5.Adjusting color gradation.
●●To adjust color gradation automatically
Every color gradation (0 to 255) can be displayed by adjusting the signal output level.
Procedure
1. Display Pattern 2 in full screen on the monitor using the “Screen adjustment pattern files”.
2. Choose “Screen” in the Setting menu, and press
.
3. Choose “Analog Adjustment” in the “Screen” menu, and press
.
4. Choose “Auto Range Adjust” in the “Analog Adjustment” menu, and press
5. Select “Yes” with
or , and press
.
.
The output range is set automatically.
6. Close Pattern 2.
6.Modify blurred characters or lines.
●●To modify blurred characters / lines
When an image is displayed with a resolution other than recommended, the characters or lines of the
displayed image may blur.
Attention
• Smoothing setting may not be required depending on the display resolution. (You cannot choose the smoothing icon.)
Adjustable range
1 to 5
Procedure
1. Choose “Screen” in the Setting menu, and press
2. Choose “Smoothing” in the “Screen” menu, and press
The “Smoothing” menu appears.
3. Use
4. Press
28
or
for adjustment.
to exit.
Chapter 2 Adjusting Screens
.
.
2-5. Screen Size Changing
●●Screen Size Changing
The image with the resolution other than the recommended resolution is displayed in full screen automatically.
You can change the screen size by using the “Screen Size” function.
Setting
Function
Full Screen
Displays an image in full screen. Images are distorted in some cases because the vertical
rate is not equal to the horizontal rate.
Enlarged
Displays an image in full screen. In some cases, a blank horizontal or vertical border
appears to equalize the vertical rate and the horizontal rate.
Normal*1
Displays images with the specified resolution.
*1 EV2336W / EV2436W only
Example: Image size 1024 × 768
EV2316W :
EV2336W :
EV2416W :
EV2436W :
Full Screen
Enlarged
Normal
(1920 × 1080)
(1920 × 1080)
(1920 × 1200)
(1920 × 1200)
(1440 × 1080)
(1440 × 1080)
(1600 × 1200)
(1600 × 1200)
(-)
(1024 × 768)
(-)
(1024 × 768)
Procedure
.
1. Choose “Screen” in the Setting menu, and press
2. Choose “Screen Size” in the “Screen” menu, and press
.
The “Screen Size” menu appears.
3. Select “Full Screen”, “Enlarged”, or “Normal” with
4. Press
or .
to exit.
Attention
• Selecting “Normal” may make some color gradations unavailable for display.
• When a 1280 × 720 resolution image is displayed on the EV2416W, the screen size is “Full Screen”.
Chapter 2 Adjusting Screens
29
●●To adjust brightness of non-display area
A border (black area with no image) around the image appears in the “Normal” or “Enlarged” mode.
Border
Procedure
1. Choose “Monitor Settings” in the Setting menu, and press
.
2. Choose “Border Intensity” in the “Monitor Settings” menu, and press
The “Border Intensity” menu appears.
3. Use
4. Press
30
or
for adjustment.
to exit.
Chapter 2 Adjusting Screens
.
Chapter 3 Setting Monitor
3-1. Adjusting Volume
This function allows you to adjust the volume.
Adjustable range
0 to 30
Procedure
.
1. Press
2. Use
or
3. Press
for adjustment.
to exit.
Note
• The volume for the speakers and the headphone can be set individually.
3-2. Selecting sound source while using the DisplayPort
signal input
This function allows you to switch sound source during DisplayPort signal input. You can select the Stereo Mini
Jack or DisplayPort.
Procedure
1. Choose “Sound” in the Setting menu, and press
.
.
2. Choose “Source” in the “Sound” menu, and press
The “Source” menu appears.
3. Select “Stereo Mini Jack” or “DisplayPort” with
4. Press
or .
to exit.
Note
• This function is available with DisplayPort signal input.
Chapter 3 Setting Monitor
31
3-3. Compensating viewing angle deficiency (EV2316W
/ EV2416W only)
When the screen is to be viewed from below, the viewing angle can be compensated for so the screen looks as if it
is being seen from directly ahead.
Off
-20˚
-40˚
Adjustable range
-40˚, -20˚, Off
Procedure
1. Choose “Monitor Settings” in the Setting menu, and press
.
.
2. Choose “Up View” in the “Monitor Settings” menu, and press
The “Up View” menu appears.
3. Select “-40˚”, “-20˚”, or “Off” with
4. Press
or .
to exit.
Attention
• The setting is turned “Off” in the following cases:
- “Orientation” of the Setting menu is set to “Portrait”.
- “sRGB” is selected from the FineContrast mode.
• Depending on the viewing angle, switching the setting may make the screen less visible.
3-4. Enabling / Disabling DDC/CI communication
This function allows you to enable / disable the DDC/CI communication (see “6-9. Glossary” (page 64)).
Procedure
1. Choose “Monitor Settings” in the Setting menu, and press
2. Choose “DDC/CI” in the “Monitor Settings” menu, and press
.
.
The “DDC/CI” menu appears.
3. Select “On” or “Off” with
4. Press
or .
to exit.
Note
• The DisplayPort input of this monitor does not support DDC/CI communication.
32
Chapter 3 Setting Monitor
3-5. Locking Operation Buttons
This function allows you to lock the settings to prevent them being changed.
Procedure
1. Press
to turn off the monitor.
while pressing
2. Hold down
to turn on the monitor.
The Lock / Unlock setting is toggled by performing the operation in step 2.
Note
• The following operations are available even if the buttons are locked:
- Turning on or off the monitor with the Power button
3-6. Setting Orientation
This function allows you to change the orientation of the Setting menu when using the monitor screen in vertical
display position.
Procedure
.
1. Choose “Monitor Settings” in the Setting menu, and press
.
2. Choose “Menu Settings” in the “Monitor Settings” menu, and press
.
3. Choose “Orientation” in the “Menu Settings” menu, and press
The “Orientation” menu appears.
4. Select “Landscape” or “Portrait” with
5. Press
or .
to exit.
6. When selecting “Portrait”, turn the monitor screen 90˚ in clockwise direction.
Attention
• Be sure that the cables are correctly connected.
• Be sure to turn the monitor screen after pulling up the screen to the uppermost position of the stand and setting the
screen tilted upward.
Note
• For using the monitor with “Portrait” position, the graphics board supporting portrait display is required. When placing
the monitor in a “Portrait” position, settings of your graphics board need to be changed. Refer to the User’s Manual of
the graphics board for details.
3-7. Showing and hiding the EIZO logo
When the monitor is turned on, the EIZO logo appears on the screen. You can choose to show or hide the display of
the EIZO logo.
Procedure
.
1. Choose “Monitor Settings” in the Setting menu, and press
2. Choose “Menu Settings” in the “Monitor Settings” menu, and press
3. Choose “Logo” in the “Menu Settings” menu, and press
.
.
The “Logo” menu appears.
4. Select “On” or “Off” with
5. Press
or .
to exit.
Chapter 3 Setting Monitor
33
3-8. Changing Setting Menu Display Position
You can change the display position of the Setting menu.
Procedure
1. Choose “Monitor Settings” in the Setting menu, and press
.
.
2. Choose “Menu Settings” in the “Monitor Settings” menu, and press
.
3. Choose “Menu Position” in the “Menu Settings” menu, and press
The “Menu Position” menu appears.
4. Choose the position with
5. Press
or .
to exit.
3-9. Setting Language
This function allows you to select a language for the Setting menu or messages.
Selectable languages
English, German, French, Spanish, Italian, Swedish, Japanese, Simplified Chinese, Traditional Chinese
Procedure
1. Choose “Monitor Settings” in the Setting menu, and press
2. Choose “Language” in the “Monitor Settings” menu, and press
The “Language” menu appears.
3. Choose a language with
4. Press
34
to exit.
Chapter 3 Setting Monitor
or .
.
.
3-10.Resetting the Monitor to the Default Settings
The setting values are reset to the default settings.
Attention
• After resetting, you cannot undo the operation.
Note
• Regarding the default setting, see “Main Default Settings” (page 60).
●●To reset the color adjustments
This function only resets the color adjustments for the currently selected mode to the default settings.
Procedure
1. Choose “Color” in the Setting menu, and press
.
2. Choose “Color Reset” in the “Color” menu, and press
3. Select “Yes” with
.
or .
.
4. Press
The color adjustments revert to the default settings.
●●To reset “EcoView Sense Settings”
This function resets adjustments for “EcoView Sense Settings” to the default settings.
Procedure
1. Press
.
2. Choose “EcoView Sense Settings” in the “EcoView Menu”, and press
.
3. Choose “Reset” in the “EcoView Sense Settings”, and press
4. Select “Yes” with
5. Press
.
or .
.
The “EcoView Sense Settings” adjustments revert to the default settings.
Note
• “EcoView Sense Settings” can be changed and reset only when “EcoView Sense” is set to “On” (see “4-4. Setting the
power saving mode when a person leaves the monitor” (page 38)).
●●To reset all adjustments to the default settings
This function resets all adjustments to the default settings.
Procedure
1. Choose “Monitor Settings” in the Setting menu, and press
2. Choose “Reset” in the “Monitor Settings” menu, and press
3. Select “Yes” with
4. Press
.
.
or .
.
All adjustments revert to the default settings.
Chapter 3 Setting Monitor
35
Chapter 4 Power Saving Functions
4-1. Setting Power Saving
●●Monitor
This function allows you to set the monitor into the power saving mode according to the PC status. When the
monitor has shifted to the power saving mode, the images on the screen are not displayed.
Attention
• Turning off the main power switch or unplugging the power cord completely shuts off power supply to the monitor.
• When the monitor is in power saving mode, devices connected to the USB downstream port will still work. Therefore,
power consumption of the monitor varies with connected devices even in the power saving mode.
• Power consumption varies even when the stereo mini jack cable is connected.
Note
• The monitor changes to the power saving mode about 15 seconds after the signal input ceases to be detected.
Procedure
.
1. Choose “PowerManager” in the Setting menu, and press
.
2. Choose “Power Save” in the “PowerManager” menu, and press
The “Power Save” menu appears.
3. Select “On” or “Off” with
4. Press
or .
to exit.
Power Saving System
Analog Signal Input
This monitor complies with the VESA DPM standard.
PC
On
Power saving
mode
STAND-BY
SUSPENDED
OFF
Power Off
Monitor
Power Indicator
Operating
Blue
Power saving mode
Orange
Power saving mode
Orange
Digital Signal Input
• DVI
This monitor complies with the DVI DMPM standard.
• DisplayPort
This monitor complies with the DisplayPort Standard V1.1a.
PC
Monitor
Power Indicator
On
Operating
Blue
Power saving mode
Power saving mode
Orange
Power Off
Power saving mode
Orange
Exiting the power saving mode
If the monitor receives input, it automatically exits the power saving mode and returns to the normal display
mode.
36
Chapter 4 Power Saving Functions
●●Audio Output
This monitor allows you to turn off the audio output from the speakers / headphone at the power saving mode.
Procedure
1. Choose “Sound” in the Setting menu, and press
.
2. Choose “Power Save” in the “Sound” menu, and press
.
The “Power Save” menu appears.
3. Select “Sound On” or “Sound Off” with
or .
to exit.
4. Press
4-2. Setting Power Indicator
This function allows you to set the power indicator (blue) ON / OFF in the monitor ON condition.
Procedure
1. Choose “Monitor Settings” in the Setting menu, and press
.
.
2. Choose “Power Indicator” in the “Monitor Settings” menu, and press
The “Power Indicator” menu appears.
3. Select “On” or “Off” with
or .
to exit.
4. Press
4-3. Enabling / Disabling Automatic Brightness
Adjustment
●●Auto EcoView
The ambient light sensor on the front side of the monitor detects the environmental brightness to adjust the
screen brightness automatically and comfortably by using the Auto EcoView function.
Attention
• Be careful not to block the ambient light sensor on the lower side of the monitor when using the Auto EcoView function.
Procedure
1. Press
.
2. Choose “Auto EcoView” in the “EcoView Menu” menu, and press
.
The “Auto EcoView” menu appears.
3. Select “High”, “Standard”, or “Off” with
4. Press
or .
to exit.
Note
• As “Brightness” in the Setting menu is changed, the auto adjustment range for Auto EcoView is also changed.
• Set to “High” if you feel a little brighter with “Standard” setting status.
Chapter 4 Power Saving Functions
37
●●EcoView Optimizer 2
Using the EcoView Optimizer 2 function automatically adjusts the screen brightness according to the white
level of the input signal. This function can reduce the power consumption while maintaining the brightness
specified by the input signal.
Procedure
1. Press
.
2. Choose “EcoView Optimizer 2” in the “EcoView Menu” menu, and press
.
The “EcoView Optimizer 2” menu appears.
3. Select “On” or “Off” with
or .
to exit.
4. Press
Note
• When “Movie” is selected from the FineContrast mode, the setting is turned “Off”.
• When the EcoView Optimizer 2 function is “On”, the appearance of pale color may change. If that bothers you, set this
function to “Off”.
4-4. Setting the power saving mode when a person
leaves the monitor
The sensor on the front side of the monitor detects the movement of a person by using the EcoView Sense function.
When a person moves away from the monitor, it shifts to the power saving mode automatically and does not display
the images on the screen to reduce the power consumption. When a person comes near the monitor again, it
recovers from the power saving mode and displays the images. The sensitivity and time until the power saving
mode is activated can be set according to the monitor usage environment and movement of the user.
Note
• At the time of shifting to power saving mode, the message that indicates shifting is displayed.
Procedure
1. Press
.
2. Choose “EcoView Sense” in the “EcoView Menu”, and press
The “EcoView Sense” menu appears.
3. Select “On” or “Off” with
4. Press
38
or .
to exit.
Chapter 4 Power Saving Functions
.
5. When “On” is selected, select “EcoView Sense Settings” for setting the details.
Item
Setting Range
Description
Time
5, 30 sec
1, 3, 5, 10, 15, 30, 45,
60 min
Specifies the time from when a person leaves the monitor until the
“No Presence detected” message appears. The monitor shifts to
the power saving mode about 20 seconds after the message is
displayed.
Sensitivity
Level 5
Level 4
Level 3
Level 2
Level 1
When the setting level is high (“Level 5” at maximum), even minor
movements of a person are detected, causing the monitor to shift
to the power saving mode only infrequently. On the other hand,
when the setting level is low (“Level 1” at minimum), only major
movements of a person are detected, allowing the monitor to shift
to the power saving mode frequently. EcoView Sense is activated
when the sensor on the front side of the monitor detects the
movement of heat. Therefore, the sensitivity should be changed
depending on the typical user’s clothes or the typical room
temperature. If the monitor shifts to or recovers from the power
saving mode contrary to your expectations, try changing the setting
level.
Reset
-
This function resets all adjustments to the default settings.
Note
• When the monitor is used in the “Portrait” direction, the detection sensitivity is lower than the “Landscape” direction.
Try increasing the sensitivity setting value when switching the mode to the power saving mode.
• To use the monitor comfortably, increase the sensitivity for high temperatures, which reduces the detection sensitivity,
and reduce the sensitivity for low temperatures, which increases the detection sensitivity.
Chapter 4 Power Saving Functions
39
4-5. Checking the power saving level
The EcoView menu allows you to check Power Reduction, CO2 Reduction, and Eco Performance Level. The more
indicators light up representing the Eco Performance Level, the higher the power saving level attained.
Example: EV2436W
Indicator
Procedure
1. Press
.
The “EcoView Menu” menu appears.
Note
• Power reduction: the backlight’s reduction of power consumption as a result of the adjusted brightness value.
CO2 reduction: converted from the “Power reduction” value, this is an estimate of the quantity of CO2 emissions reduced
when using the monitor for 1 hour.
* The numeric value is a result of a calculation based on a default setting (0.000555 t -CO2/kWh) determined by a Japanese
ministerial ordinance (2006, Ministry of Economy, Trade and Industry, Ministry of Environment, civil code article 3) and
may differ depending on country and year.
4-6. Enabling / Disabling Auto Power-OFF
This function allows you to switch the setting to turn off the monitor automatically after a specified time has passed
in the power saving mode.
Adjustable range
Off, 0, 1, 2, 3, 5, 10, 15, 20, 25, 30, 45 min, 1, 2, 3, 4, 5 h
Procedure
.
1. Choose “PowerManager” in the Setting menu, and press
2. Choose “Eco Timer” in the “PowerManager”, and press
3. Select “Off” or time to turn off the monitor with
4. Press
40
to exit.
Chapter 4 Power Saving Functions
or .
.
Chapter 5 Troubleshooting
If a problem still remains after applying the suggested remedies, contact your local EIZO representative.
5-1. No picture
Problem
1. No picture
• Power indicator does not light.
Possible cause and remedy
•
•
•
•
Check whether the power cord is connected properly.
Turn the main power switch on.
Press .
Turn off the main power, and then turn it on again a few
minutes later.
• Power indicator is lighting blue.
• Increase “Brightness”, “Contrast”, or “Gain” in the Setting
menu (see “To perform advanced adjustments” (page 20)).
• Power indicator is lighting orange.
•
•
•
•
Switch the input signal with
.
Move the mouse or press any key on the keyboard.
Check whether the PC is turned on.
When the EcoView Sense function is “On”, the monitor
may have shifted to the power saving mode. Come near
to the monitor. If the screen is not displayed, move the
mouse or press any key on the keyboard.
• Depending on the PC and graphics board, the input signal
is not detected and the monitor does not recover from
the power saving mode. If the screen is not displayed
even after moving the mouse or pressing any key on the
keyboard, turn the monitor off and on using its power
button. When the screen is displayed, execute the
following procedure. The problem may be improved.
1. Press
to turn off the monitor.
2. Hold down
while pressing to turn on the
monitor.
“x” is displayed on the menu title of “Information” of the
Setting menu (see “6-6. Displaying Monitor Information”
(page 53)).
3. Reboot the PC.
To return to the previous setting, perform steps 1 to 3
again.
• Power indicator is flashing orange.
• The device that is connected using DisplayPort has a
problem. Solve the problem, turn off the monitor, and then
turn it on again. Refer to the User’s Manual of the output
device for further details.
Chapter 5 Troubleshooting
41
Problem
2. The message below appears.
• The message shows that the input signal is
out of the specified frequency range.
Example:
Possible cause and remedy
This message appears when the signal is not input correctly
even when the monitor functions properly.
• Check whether the PC is configured to meet the resolution
and vertical scan frequency requirements of the monitor
(see “2-1. Compatible Resolutions” (page 14)).
• Reboot the PC.
• Select an appropriate setting using the graphics board’s
utility. Refer to the User’s Manual of the graphics board
for details.
5-2. Imaging problems (for both digital and analog)
Problem
42
Possible cause and remedy
1. The screen is too bright or too dark.
• Use “Brightness” or “Contrast” in the Setting menu to
adjust it. (The LCD monitor backlight has a limited life
span. When the screen becomes dark or begins to flicker,
contact your local EIZO representative.)
• If the screen is too bright, turn on Auto EcoView. The
monitor detects the environmental brightness to adjust the
screen brightness automatically.
2. Characters are blurred.
• Check whether the PC is configured to meet the resolution
and vertical scan frequency requirements of the monitor
(see “2-1. Compatible Resolutions” (page 14)).
• When an image is displayed with a resolution other than
recommended, the characters or lines of the displayed
image may blur. Use “Smoothing” and “Screen Size” in the
Setting menu to adjust the display (see “To modify blurred
characters / lines” (page 28), and “Screen Size Changing”
(page 29)).
3. Afterimages appear.
• Afterimages are particular to LCD monitors. Avoid
displaying the same image for a long time.
• Use the screen saver or power save function to avoid
displaying the same image for extended periods of time.
4. Green / red / blue / white dots or defective
dots remain on the screen.
• This is due to LCD panel characteristics and is not a
failure.
5. Interference patterns or pressure marks
remain on the screen.
• Leave the monitor with a white or black screen. The
symptom may disappear.
6. Noise appears on the screen.
• In the Setting menu, set “Overdrive” to “Off” (see “To set
overdrive intensity (EV2336W / EV2436W only)” (page 23)).
• When entering the HDCP signals, the normal images may
not be displayed immediately.
Chapter 5 Troubleshooting
5-3. Imaging problems (for digital only)
Problem
Possible cause and remedy
1. The monitor configuration is changed to
single under the multiple monitor configuration (when DisplayPort is connected).
• When two monitors are connected to one PC using
DisplayPort, and the power to one of the monitors is
turned off with the power button, the screen setting may
be changed to the single monitor configuration. In such a
case, enable the “DP HotPlug” function with the following
procedures. Enabling this function may increase the
power consumption.
1. Press to turn off the monitor.
2. Hold down while pressing to turn on the monitor.
Each time the operation enables / disables this function
alternatively.
The current setting status can be identified based on the
color used to display the input port or signal error.
Setting
Input port
Signal Error
Disable
(default
setting)
Enable
5-4. Imaging problems (for analog only)
Problem
Possible cause and remedy
1. Display position is incorrect.
• Use “Position” in the Setting menu to correct the image
position (see “To correct the screen position” (page 27)).
• If the problem persists, use the graphics board’s utility if
available to change the display position.
2. Vertical bars appear on the screen or a
part of the image is flickering.
• Use “Clock” in the Setting menu to adjust it (see “To
eliminate vertical bars” (page 26)).
3. Whole screen is flickering or blurring.
• Use “Phase” in the Setting menu to adjust it (see “To
remove flickering or blurring” (page 27)).
Chapter 5 Troubleshooting
43
5-5. Other problems
Problem
44
Possible cause and remedy
1. The Setting menu does not appear.
• Check whether the operation lock function is active (see
“3-5. Locking Operation Buttons” (page 33)).
2. The “Smoothing” on the Setting menu
“Screen” cannot be selected.
• You cannot choose “smoothing” when the screen is
displayed in the following resolutions or settings.
--The resolution is 1920 × 1080 (EV2316W / EV2336W)
--The resolution is 1920 × 1200 (EV2416W / EV2436W)
--Screen Size is “Normal” (EV2336W / EV2436W only)
3. The auto adjustment function does not
work.
• This function does not work during digital signal input.
• This function is intended for use on the Macintosh and
on AT-compatible PC running Windows. It does not work
properly when an image is displayed only on a part of the
screen (command prompt window, for example) or when a
black background (wallpaper, etc.) is in use.
• This function does not work correctly with some graphics
boards.
4. No audio output.
• Check whether the stereo mini jack cable is connected
properly.
• Check whether volume is set to 0.
• Check the setting of the PC and the audio playback
software.
• During DisplayPort signal input, check the “Source”
setting (see “3-2. Selecting sound source while using the
DisplayPort signal input” (page 31)).
5. (When using EcoView Sense)
The images remain to be displayed when
you move away from the monitor. / The
images do not reappear when you come
near it.
• Check the setting environment of the monitor. Presence
Sensor may not work correctly in the following
environments.
--The monitor is located in a place affected by wind.
--There is some heat emitting device near the monitor.
--There is some obstacle in front of the sensor.
• Check whether any dirt on the sensor. Clean the sensor
with a soft cloth.
• Check whether you are in front of the monitor. The
EcoView Sense function is activated when the sensor on
the front side of the monitor detects the movement of heat.
• In the high temperature conditions, the monitor may not
recover from the power saving mode. If the screen is not
displayed even after moving the mouse or pressing any
key on the keyboard, turn the monitor off and on using its
power button. When the screen is displayed, increase the
detection sensitivity value (see “4-4. Setting the power
saving mode when a person leaves the monitor” (page 38)).
Chapter 5 Troubleshooting
Problem
6. USB devices connected to the monitor do
not work.
Possible cause and remedy
• Check whether the USB cable is connected correctly (see
“6-5. Making Use of USB (Universal Serial Bus)” (page 52)).
• Change the USB port to another one. If the PC or
peripheral devices works correctly by changing the USB
port, contact your local EIZO representative. (Refer to the
manual of the PC for details.)
• Reboot the PC.
• If the peripheral devices work correctly when the PC and
peripheral devices are connected directly, please contact
your local EIZO representative.
• Check whether the PC and OS are USB compliant. (For
USB compliance of the respective devices, consult their
manufacturers.)
• Check the PC’s BIOS setting for USB when using
Windows. (Refer to the manual of the PC for details.)
Chapter 5 Troubleshooting
45
Chapter 6 Reference
6-1. Attaching the Optional Arm
An optional arm (or an optional stand) can be attached by removing the stand section. Please refer to our web site
for the corresponding optional arm (or optional stand). http://www.eizo.com
Attention
• When attaching an arm or stand, follow the instructions of their User’s Manual.
• When using another manufacturer’s arm or stand, confirm the following in advance and select one conforming to the VESA
standard. Use the screws securing the unit and the stand.
- Clearance between the screw holes: 100 mm × 100 mm
- Thickness of plate: 2.6 mm
- Strong enough to support weight of the monitor unit (except the stand) and attachments such as cables.
• When using an arm or stand, attach it to meet the following tilt angles of the monitor.
- Up 45˚, down 45˚ (horizontal display, and vertical display rotated 90 degrees clockwise)
• Connect the cables after attaching an arm or stand.
• Do not move the removed stand up and down. Doing so may result in injury or device damage.
• The monitor and arm or stand are heavy. Dropping them may result in injury or equipment damage.
• When setting the monitor to the portrait style, turn the monitor screen 90˚ in clockwise direction.
Procedure
1.Lay the LCD monitor on a soft cloth spread over on a stable surface with the
panel surface facing down.
2.Remove the stand.
Prepare a screwdriver. Loosen the screws (four) securing the unit and the stand with the screwdriver.
3.Attach the arm or stand to the monitor.
Secure the monitor to the arm or stand using the screws specified in the User’s Manual of the arm or stand.
46
Chapter 6 Reference
6-2. Detaching/Attaching Stand Base
Detaching procedure
The stand base that was attached during setup can be detached using the following procedures.
1.Lay the LCD monitor on a soft cloth spread over on a stable surface with the
panel surface facing down.
2.Turn the fixing screw on the stand base to detach it.
Note
• The fixing screw can be removed by hand. If the fixing screw is too tight, use a coin or flathead screwdriver.
3.Turn the stand base in the counterclockwise direction to detach it.
Top of the stand base
Align the “-” mark on the stand brace
with the “●” mark on the stand base.
Note
• Reattach the fixing screw onto the stand base for when the stand base is used again.
Chapter 6 Reference
47
Attaching procedure
The once removed the stand base can be attached to the monitor again with the following procedures.
1.Check that the fixing screw is firmly attached to the bottom of the stand base.
2.Place the stand base on a stable surface.
3.Insert the stand brace into the stand base.
Align the “-” mark on the stand brace
with the “●” mark on the stand base.
4.Turn the stand brace in the clockwise direction until it clicks.
Align the “-” mark on the stand brace
with the “-” mark on the stand base.
48
Chapter 6 Reference
6-3. Attaching/Detaching Cable Holder
A cable holder is supplied with this product. Use the holder to organize the cables connected to the monitor.
Attaching procedure
1.Pass the cables through the cable holder.
2.Close the opening in the cable holder.
3.While holding the cable holder closed, attach it onto the stand.
Note
• The cable holder can be inserted either perpendicular or parallel to the stand. Change the direction of the cable holder
according to the conditions of the cables.
Chapter 6 Reference
49
Detaching procedure
1.Close the opening in the cable holder.
2.While holding the cable holder closed, remove it from the stand.
50
Chapter 6 Reference
6-4. Connecting Multiple PCs
The product has multiple connections to PCs and allows you to switch to one of the connections for display.
Connection examples
DisplayPort
connector
Digital
(DisplayPort)
Signal cable
(supplied PP200)
DVI-D connector
Digital (DVI)
Signal cable
(supplied FD-C39)
D-Sub
connector
Analog (D-Sub)
Signal cable
(option MD-C87)
DisplayPort 
connector
DVI connector
D-Sub mini 15-pin
connector
To PC 1
To PC 2
To PC 3
●●To switch among input signals
The input signal switches each time
is pressed.
When the signal is switched, the active input port name appears at the top right corner of the screen.
Chapter 6 Reference
51
●●To set input signal selection
Setting
Function
Auto
The monitor recognizes the connector through which PC signals are input.
When a PC is turned off or enters the power saving mode, the monitor automatically
displays another signal.
Manual
The monitor displays the signal from the selected connector despite the signal input. Select
the input signal for display using the
operation button.
Procedure
.
1. Choose “Monitor Settings” from the Adjustment menu, and press
2. Choose “Input Signal” from “Monitor Settings”, and press
3. Select “Auto” or “Manual” with
4. Press
.
or .
to exit.
Note
• If you select “Auto”, the monitor enters the power saving mode after all the PCs have entered the power saving mode or
have been switched off.
6-5. Making Use of USB (Universal Serial Bus)
This monitor has a USB hub. It works as a USB hub when connected to a USB-compatible PC, allowing the
connection of peripheral USB devices.
●●Required System Environment
• A PC equipped with a USB port
• Windows 2000 / XP / Vista / 7 / 8 or Mac OS 9.2.2 and Mac OS X 10.2 or later
• USB cable (commercially available product)
Attention
• This monitor may not work depending on PC, OS or peripheral devices to be used. For USB compatibility of peripheral
devices, contact their manufacturers.
• When the monitor is in power saving mode, devices connected to the USB downstream port will still work. Therefore,
power consumption of the monitor varies with connected devices even in the power saving mode.
• When the main power of the monitor is Off, a device connected to the USB downstream port will not operate.
52
Chapter 6 Reference
●●Connection Procedure (Setup of USB Function)
1. Connect the monitor first to a PC using the signal cable, and run the PC.
2. Connect the USB cable between the USB downstream port of the PC and the USB upstream port of the
monitor.
The USB hub function is set up automatically upon connection of the USB cable.
3. Connect the peripheral USB devices to the USB downstream port of the monitor.
USB
downstream
port
USB
upstream
port
6-6. Displaying Monitor Information
This function allows you to display the model name, serial number, usage time, resolution, and input signal.
Procedure
1. Choose “Information” in the Setting menu, and press
.
The “Information” menu appears.
Attention
• When you turn on the monitor for the first time, the usage time may be more than 0 due to a factory inspection.
Chapter 6 Reference
53
6-7. Specifications
●●EV2316W
LCD Panel
Size
23.0-inch (580 mm)
Type
TFT color LCD, LED backlight
Surface treatment
Anti-Glare Hard Coating
Viewing angles
Horizontal 170˚, vertical 160˚ (CR≥10)
Dot Pitch
0.2655 mm
Response Time
Black-white-black: Approx. 5 ms
Horizontal Scan Analog
Frequency
Digital
31 - 68 kHz
DVI
31 - 68 kHz
DisplayPort 31 - 68 kHz
Vertical Scan
Frequency
Analog
Digital
55 - 61 Hz (non-interlace)
DVI
59 - 61 Hz (non-interlace)
DisplayPort 59 - 61 Hz (non-interlace)
Resolution
Max. Dot Clock
1920 Dots × 1080 Lines
Analog
Digital
148.5 MHz
DVI
148.5 MHz
DisplayPort 148.5 MHz
Max. Display Color
Approx. 16.77 million colors
Display Area (H × V)
509.7 mm (20.1 inch) × 286.7 mm (11.3 inch)
Power Supply
100 - 120 VAC ±10 %, 50 / 60 Hz 0.75 A
200 - 240 VAC ±10 %, 50 / 60 Hz 0.45 A
Power
Consumption
Screen Display On
43 W or less
Power saving mode
0.3 W or less (with no USB connections, “EcoView Sense”: “Off”, and
“Sound” - “Power Save”: “Sound Off”)
Power Off
0.3 W or less
Main Power Off
Input Signal Connector
0W
D-Sub mini 15-pin
DVI-D connector (Applicable to HDCP)
DisplayPort (Standard V1.1a, applicable to HDCP)
Applicable Format (Audio signal)
- 2ch linear PCM 
(32 kHz / 44.1 kHz / 48 kHz / 88.2 kHz / 96 kHz)
Analog Input Signal (Sync)
Separate, TTL, positive / negative
Analog Input Signal (Video)
Analog, Positive (0.7 Vp-p / 75 Ω)
Digital Signal (DVI) Transmission System TMDS (Single Link)
54
Audio Output
Speaker output: 1.0 W + 1.0 W (8 Ω, THD+N: 10 % or less)
Headphone output: 2 mW + 2 mW (32 Ω, THD+N: 3 % or less)
Line Input
Input impedance: 44 kΩ (typ.)
Input level: 2.0 Vrms (Max.)
Plug & Play
Analog / Digital (DVI-D) : VESA DDC 2B / EDID structure 1.3
Digital (DisplayPort) : VESA DisplayPort / EDID structure 1.4
Dimensions
(Width) ×
(Height) ×
(Depth)
Main unit
540 mm (21.3 inch) × 338.5 - 478.5 mm (13.3 inch - 18.8 inch) × 233
mm (9.2 inch)
Main unit (without
stand)
540 mm (21.3 inch) × 317.5 mm (12.5 inch) × 56 mm (2.2 inch)
Mass
Main unit
Approx. 5.4 kg (11.9 lbs.)
Main unit (without
stand)
Approx. 3.1 kg (6.8 lbs.)
Chapter 6 Reference
Movable range
Environmental
Conditions
Temperature
Humidity
Air Pressure
USB
Tilt:
35˚ Up, 5˚ Down
Swivel:
344˚
Adjustable height:
140 mm (5.5 inch)
Rotation:
90˚ (Clockwise)
Operating:
5˚C to 35˚C (41˚F to 95˚F)
Transportation/
Storage:
-20˚C to 60˚C (-4˚F to 140˚F)
Operating:
20 % to 80 % R.H. (no condensation)
Transportation/
Storage:
10 % to 90 % R.H. (no condensation)
Operating:
700 to 1,060 hPa
Transportation/
Storage:
200 to 1,060 hPa
Standard
USB Specification Revision 2.0
Port
Upstream port × 1, Downstream port × 2
Communication Speed 480 Mbps (high), 12 Mbps (full), 1.5 Mbps (low)
Supply current
Downstream:
Max. 500mA/1 port
●●EV2336W
LCD Panel
Size
23.0-inch (580 mm)
Type
TFT color LCD, LED backlight
Surface treatment
Anti-Glare Hard Coating
Viewing angles
Horizontal 178˚, vertical 178˚ (CR≥10)
Dot Pitch
0.2652 mm
Response Time
Black-white-black: Approx. 16 ms
Gray-to-gray: Approx. 6 ms (Overdrive setting: Enhanced)
Horizontal Scan Analog
Frequency
Digital
31 - 81 kHz
DVI
31 - 68 kHz
DisplayPort 31 - 68 kHz
Vertical Scan
Frequency
Analog
Digital
55 - 76 Hz (non-interlace)
DVI
59 - 61 Hz (non-interlace) (VGA TEXT: 69 - 71 Hz)
DisplayPort 59 - 61 Hz (non-interlace) (VGA TEXT: 69 - 71 Hz)
Resolution
Max. Dot Clock
1920 Dots × 1080 Lines
Analog
Digital
148.5 MHz
DVI
148.5 MHz
DisplayPort 148.5 MHz
Max. Display Color
Approx. 16.77 million colors
Display Area (H × V)
509.1 mm (20 inch) × 286.4 mm (11.3 inch)
Power Supply
100 - 120 VAC ±10 %, 50 / 60 Hz 0.8 A
200 - 240 VAC ±10 %, 50 / 60 Hz 0.5 A
Power
Consumption
Screen Display On
40 W or less
Power saving mode
0.3 W or less (with no USB connections, “EcoView Sense”: “Off”, and
“Sound” - “Power Save”: “Sound Off”)
Power Off
0.3 W or less
Main Power Off
Input Signal Connector
0W
D-Sub mini 15-pin
DVI-D connector (Applicable to HDCP)
DisplayPort (Standard V1.1a, applicable to HDCP)
Applicable Format (Audio signal)
- 2ch linear PCM 
(32 kHz / 44.1 kHz / 48 kHz / 88.2 kHz / 96 kHz)
Chapter 6 Reference
55
Analog Input Signal (Sync)
Separate, TTL, positive / negative
Analog Input Signal (Video)
Analog, Positive (0.7 Vp-p / 75 Ω)
Digital Signal (DVI) Transmission System TMDS (Single Link)
Audio Output
Speaker output: 1.0 W + 1.0 W (8 Ω, THD+N: 10 % or less)
Headphone output: 2 mW + 2 mW (32 Ω, THD+N: 3 % or less)
Line Input
Input impedance: 44 kΩ (typ.)
Input level: 2.0 Vrms (Max.)
Plug & Play
Analog / Digital (DVI-D) : VESA DDC 2B / EDID structure 1.3
Digital (DisplayPort) : VESA DisplayPort / EDID structure 1.4
Dimensions
(Width) ×
(Height) ×
(Depth)
Main unit
540 mm (21.3 inch) × 338.5 - 478.5 mm (13.3 inch - 18.8 inch) × 233
mm (9.2 inch)
Main unit (without
stand)
540 mm (21.3 inch) × 317.5 mm (12.5 inch) × 56 mm (2.2 inch)
Mass
Main unit
Approx. 6.1 kg (13.4 lbs.)
Main unit (without
stand)
Approx. 3.7 kg (8.2 lbs.)
Movable range
Environmental
Conditions
Temperature
Humidity
Air Pressure
USB
Tilt:
35˚ Up, 5˚ Down
Swivel:
344˚
Adjustable height:
140 mm (5.5 inch)
Rotation:
90˚ (Clockwise)
Operating:
5˚C to 35˚C (41˚F to 95˚F)
Transportation/
Storage:
-20˚C to 60˚C (-4˚F to 140˚F)
Operating:
20 % to 80 % R.H. (no condensation)
Transportation/
Storage:
10 % to 90 % R.H. (no condensation)
Operating:
700 to 1,060 hPa
Transportation/
Storage:
200 to 1,060 hPa
Standard
USB Specification Revision 2.0
Port
Upstream port × 1, Downstream port × 2
Communication Speed 480 Mbps (high), 12 Mbps (full), 1.5 Mbps (low)
Supply current
56
Chapter 6 Reference
Downstream:
Max. 500mA/1 port
●●EV2416W
LCD Panel
Size
24.1-inch (610 mm)
Type
TFT color LCD, LED backlight
Surface treatment
Anti-Glare Hard Coating
Viewing angles
Horizontal 170˚, vertical 160˚ (CR≥10)
Dot Pitch
0.270 mm
Response Time
Black-white-black: Approx. 5 ms
Horizontal Scan Analog
Frequency
Digital
31 - 76 kHz
DVI
31 - 76 kHz
DisplayPort 31 - 76 kHz
Vertical Scan
Frequency
Analog
Digital
55 - 61 Hz (non-interlace)
DVI
59 - 61 Hz (non-interlace)
DisplayPort 59 - 61 Hz (non-interlace)
Resolution
Max. Dot Clock
1920 Dots × 1200 Lines
Analog
Digital
193.3 MHz
DVI
162 MHz
DisplayPort 162 MHz
Max. Display Color
Approx. 16.77 million colors
Display Area (H × V)
518.4 mm × 324.0 mm (20.4 inch × 12.8 inch)
Power Supply
100 - 120 VAC ±10 %, 50 / 60 Hz 0.8 A
200 - 240 VAC ±10 %, 50 / 60 Hz 0.5 A
Power
Consumption
Screen Display On
40 W or less
Power saving mode
0.3 W or less (with no USB connections, “EcoView Sense”: “Off”, and
“Sound” - “Power Save”: “Sound Off”)
Power Off
0.3 W or less
Main Power Off
0W
Input Signal Connector
D-Sub mini 15-pin
DVI-D connector (Applicable to HDCP)
DisplayPort (Standard V1.1a, applicable to HDCP)
Applicable Format (Audio signal)
- 2ch linear PCM 
(32 kHz / 44.1 kHz / 48 kHz / 88.2 kHz / 96 kHz)
Analog Input Signal (Sync)
Separate, TTL, positive / negative
Analog Input Signal (Video)
Analog, Positive (0.7 Vp-p / 75 Ω)
Digital Signal (DVI) Transmission System TMDS (Single Link)
Audio Output
Speaker output: 1.0 W + 1.0 W (8 Ω, THD+N: 10 % or less)
Headphone output: 2 mW + 2 mW (32 Ω, THD+N: 3 % or less)
Line Input
Input impedance: 44 kΩ (typ.)
Input level: 2.0 Vrms (Max.)
Plug & Play
Analog / Digital (DVI-D) : VESA DDC 2B / EDID structure 1.3
Digital (DisplayPort) : VESA DisplayPort / EDID structure 1.4
Dimensions
(Width) ×
(Height) ×
(Depth)
Main unit
552.5 mm (21.8 inch) × 368 - 499 mm (14.5 - 19.6 inch) × 233 mm (9.2
inch)
Main unit (without
stand)
552.5 mm (21.8 inch) × 358 mm (14.1 inch) × 57 mm (2.24 inch)
Mass
Main unit
Approx. 6.1 kg (13.4 lbs.)
Main unit (without
stand)
Approx. 3.7 kg (8.2 lbs.)
Chapter 6 Reference
57
Movable range
Environmental
Conditions
Temperature
Humidity
Air Pressure
USB
Tilt:
35˚ Up, 5˚ Down
Swivel:
344˚
Adjustable height:
140 mm (5.5 inch) (131 mm (5.2 inch) for tilt of
0˚)
Rotation:
90˚ (Clockwise)
Operating:
5˚C to 35˚C (41˚F to 95˚F)
Transportation/
Storage:
-20˚C to 60˚C (-4˚F to 140˚F)
Operating:
20 % to 80 % R.H. (no condensation)
Transportation/
Storage:
10 % to 90 % R.H. (no condensation)
Operating:
700 to 1,060 hPa
Transportation/
Storage:
200 to 1,060 hPa
Standard
USB Specification Revision 2.0
Port
Upstream port × 1, Downstream port × 2
Communication Speed 480 Mbps (high), 12 Mbps (full), 1.5 Mbps (low)
Supply current
Downstream:
Max. 500mA/1 port
●●EV2436W
LCD Panel
Size
24.1-inch (610 mm)
Type
TFT color LCD, LED backlight
Surface treatment
Anti-Glare Hard Coating
Viewing angles
Horizontal 178˚, vertical 178˚ (CR≥10)
Dot Pitch
0.270 mm
Response Time
Black-white-black: Approx. 14 ms
Gray-to-gray: Approx. 6 ms (Overdrive setting: Enhanced)
Horizontal Scan Analog
Frequency
Digital
31 - 81 kHz
DVI
31 - 76 kHz
DisplayPort 31 - 76 kHz
Vertical Scan
Frequency
Analog
Digital
55 - 76 Hz (non-interlace) (WUXGA: - 61 Hz)
DVI
59 - 61 Hz (non-interlace) (VGA TEXT: 69 - 71 Hz)
DisplayPort 59 - 61 Hz (non-interlace) (VGA TEXT: 69 - 71 Hz)
Resolution
Max. Dot Clock
1920 Dots × 1200 Lines
Analog
Digital
193.3 MHz
DVI
162 MHz
DisplayPort 162 MHz
Max. Display Color
Approx. 16.77 million colors
Display Area (H × V)
518.4 mm × 324.0 mm (20.4 inch × 12.8 inch)
Power Supply
100 - 120 VAC ±10 %, 50 / 60 Hz 1.0 A
200 - 240 VAC ±10 %, 50 / 60 Hz 0.6 A
Power
Consumption
58
Screen Display On
60 W or less
Power saving mode
0.3 W or less (with no USB connections, “EcoView Sense”: “Off”, and
“Sound” - “Power Save”: “Sound Off”)
Power Off
0.3 W or less
Main Power Off
0W
Chapter 6 Reference
Input Signal Connector
D-Sub mini 15-pin
DVI-D connector (Applicable to HDCP)
DisplayPort (Standard V1.1a, applicable to HDCP)
Applicable Format (Audio signal)
- 2ch linear PCM 
(32 kHz / 44.1 kHz / 48 kHz / 88.2 kHz / 96 kHz)
Analog Input Signal (Sync)
Separate, TTL, positive / negative
Analog Input Signal (Video)
Analog, Positive (0.7 Vp-p / 75 Ω)
Digital Signal (DVI) Transmission System TMDS (Single Link)
Audio Output
Speaker output: 1.0 W + 1.0 W (8 Ω, THD+N: 10 % or less)
Headphone output: 2 mW + 2 mW (32 Ω, THD+N: 3 % or less)
Line Input
Input impedance: 44 kΩ (typ.)
Input level: 2.0 Vrms (Max.)
Plug & Play
Analog / Digital (DVI-D) : VESA DDC 2B / EDID structure 1.3
Digital (DisplayPort) : VESA DisplayPort / EDID structure 1.4
Dimensions
(Width) ×
(Height) ×
(Depth)
Main unit
552.5 mm (21.8 inch) × 368 - 499 mm (14.5 - 19.6 inch) × 233 mm (9.2
inch)
Main unit (without
stand)
552.5 mm (21.8 inch) × 358 mm (14.1 inch) × 57 mm (2.24 inch)
Mass
Main unit
Approx. 6.4 kg (14.1 lbs.)
Main unit (without
stand)
Approx. 4.1 kg (9 lbs.)
Movable range
Environmental
Conditions
Temperature
Humidity
Air Pressure
USB
Tilt:
35˚ Up, 5˚ Down
Swivel:
344˚
Adjustable height:
140 mm (5.5 inch) (131 mm (5.2 inch) for tilt of
0˚)
Rotation:
90˚ (Clockwise)
Operating:
5˚C to 35˚C (41˚F to 95˚F)
Transportation/
Storage:
-20˚C to 60˚C (-4˚F to 140˚F)
Operating:
20 % to 80 % R.H. (no condensation)
Transportation/
Storage:
10 % to 90 % R.H. (no condensation)
Operating:
700 to 1,060 hPa
Transportation/
Storage:
200 to 1,060 hPa
Standard
USB Specification Revision 2.0
Port
Upstream port × 1, Downstream port × 2
Communication Speed 480 Mbps (high), 12 Mbps (full), 1.5 Mbps (low)
Supply current
Downstream:
Max. 500mA/1 port
Chapter 6 Reference
59
●●Main Default Settings
Auto EcoView
Standard
EcoView Optimizer 2
On
EcoView Sense
Off
FineContrast Mode
User1
Screen Size
Full Screen
Smoothing
3
Power Save
On
Eco Timer
Off
Language
English
Menu Position
Center
Input Signal
Manual
●●Outside Dimensions
EV2316W / EV2336W
Unit: mm
344°
SWIVEL
540
511.8
14.1
220
14.3
14.1
24.5
56
349
315
100
Chapter 6 Reference
108.7
108.8
140
368
73
187
154
34
60
100
5° 35°
140
320
14.4
161
50
10
°
90
PIVOT
288.8
317.5
590
TILT
233
7
220
275
90
EV2416W / EV2436W
Unit: mm
344°
SWIVEL
16
226.25
16
552.5
520.5
100
226.25
35°
129
TILT
100
5°
368
140
129
131
55
10
141
169
134
16
320
326
358
596
°
90
PIVOT
44
16
28.5
57
349
315
33
233
19
275
289
90
●●Accessories
Signal cable
Cleaning Kit
MD-C87
EIZO “ScreenCleaner”
For the latest information about the accessories, refer to our web site.
http://www.eizo.com
Chapter 6 Reference
61
6-8. Preset Timing
The following table shows factory preset analog signal timing.
Attention
• Display position may be deviated depending on the PC connected, which may require screen adjustment using Setting menu.
• If a signal other than those listed in the table is input, adjust the screen using the Setting menu. However, screen display may
still be incorrect even after the adjustment.
• When interlace signals are used, the screen cannot be displayed correctly even after screen adjustment using the Setting
menu.
●●EV2316W
Resolution
Applicable
Signals
640 × 480
800 × 600
1024 × 768
1280 × 720
1280 × 960
1280 × 1024
1680 × 1050
1680 × 1050
1920 × 1080
VGA
VESA
VESA
CEA-861
VESA
VESA
VESA CVT
VESA CVT RB
CEA-861
Frequency
Dot Clock:
MHz
25.18
40.00
65.00
74.25
108.00
108.00
146.25
119.00
148.50
●●EV2336W
62
Resolution
Applicable
Signals
640 × 480
640 × 480
640 × 480
720 × 400
800 × 600
800 × 600
800 × 600
800 × 600
1024 × 768
1024 × 768
1024 × 768
1280 × 720
1280 × 960
1280 × 1024
1280 × 1024
1680 × 1050
1680 × 1050
1920 × 1080
VGA
VESA
VESA
VGA TEXT
VESA
VESA
VESA
VESA
VESA
VESA
VESA
CEA-861
VESA
VESA
VESA
VESA CVT
VESA CVT RB
CEA-861
Chapter 6 Reference
Polarity
Horizontal:
Vertical: Hz Horizontal
kHz
31.47
37.88
48.36
45.00
60.00
63.98
65.29
64.67
67.50
59.94
60.32
60.00
60.00
60.00
60.02
59.95
59.88
60.00
Frequency
Dot Clock:
MHz
25.18
31.50
31.50
28.32
36.00
40.00
50.00
49.50
65.00
75.00
78.75
74.25
108.00
108.00
135.00
146.25
119.00
148.50
Negative
Positive
Negative
Positive
Positive
Positive
Negative
Positive
Positive
Negative
Positive
Negative
Positive
Positive
Positive
Positive
Negative
Positive
Polarity
Horizontal:
Vertical: Hz Horizontal
kHz
31.47
37.86
37.50
31.47
35.16
37.88
48.08
46.88
48.36
56.48
60.02
45.00
60.00
63.98
79.98
65.29
64.67
67.50
Vertical
59.94
72.81
75.00
70.09
56.25
60.32
72.19
75.00
60.00
70.07
75.03
60.00
60.00
60.02
75.03
59.95
59.88
60.00
Negative
Negative
Negative
Negative
Positive
Positive
Positive
Positive
Negative
Negative
Positive
Positive
Positive
Positive
Positive
Negative
Positive
Positive
Vertical
Negative
Negative
Negative
Positive
Positive
Positive
Positive
Positive
Negative
Negative
Positive
Positive
Positive
Positive
Positive
Positive
Negative
Positive
●●EV2416W
Resolution
Applicable
Signals
640 × 480
800 × 600
1024 × 768
1280 × 720
1280 × 960
1280 × 1024
1600 × 1200
1680 × 1050
1680 × 1050
1920 × 1200
1920 × 1200
VGA
VESA
VESA
CEA-861
VESA
VESA
VESA
VESA CVT
VESA CVT RB
VESA CVT
VESA CVT RB
Frequency
Dot Clock:
MHz
25.18
40.00
65.00
74.25
108.00
108.00
162.00
146.25
119.00
193.25
154.00
●●EV2436W
Resolution
Applicable
Signals
640 × 480
640 × 480
640 × 480
720 × 400
800 × 600
800 × 600
800 × 600
800 × 600
1024 × 768
1024 × 768
1024 × 768
1280 × 720
1280 × 960
1280 × 1024
1280 × 1024
1600 × 1200
1680 × 1050
1680 × 1050
1920 × 1200
1920 × 1200
VGA
VESA
VESA
VGA TEXT
VESA
VESA
VESA
VESA
VESA
VESA
VESA
CEA-861
VESA
VESA
VESA
VESA
VESA CVT
VESA CVT RB
VESA CVT
VESA CVT RB
Polarity
Horizontal:
Vertical: Hz Horizontal
kHz
31.47
37.88
48.36
45.00
60.00
63.98
75.00
65.29
64.67
74.56
74.04
59.94
60.32
60.00
60.00
60.00
60.02
60.00
59.95
59.88
59.89
59.95
Frequency
Dot Clock:
MHz
25.18
31.50
31.50
28.32
36.00
40.00
50.00
49.50
65.00
75.00
78.75
74.25
108.00
108.00
135.00
162.00
146.25
119.00
193.25
154.00
Negative
Positive
Negative
Positive
Positive
Positive
Positive
Negative
Positive
Negative
Positive
Negative
Positive
Negative
Positive
Positive
Positive
Positive
Positive
Negative
Positive
Negative
Polarity
Horizontal:
Vertical: Hz Horizontal
kHz
31.47
37.86
37.50
31.47
35.16
37.88
48.08
46.88
48.36
56.48
60.02
45.00
60.00
63.98
79.98
75.00
65.29
64.67
74.56
74.04
Vertical
59.94
72.81
75.00
70.09
56.25
60.32
72.19
75.00
60.00
70.07
75.03
60.00
60.00
60.02
75.03
60.00
59.95
59.88
59.89
59.95
Negative
Negative
Negative
Negative
Positive
Positive
Positive
Positive
Negative
Negative
Positive
Positive
Positive
Positive
Positive
Positive
Negative
Positive
Negative
Positive
Vertical
Negative
Negative
Negative
Positive
Positive
Positive
Positive
Positive
Negative
Negative
Positive
Positive
Positive
Positive
Positive
Positive
Positive
Negative
Positive
Negative
Chapter 6 Reference
63
6-9. Glossary
Clock
The analog signal input monitor needs to reproduce a clock of the same frequency as the dot clock of the
graphics system in use, when the analog signal is converted to a digital signal for image display. This is
called clock adjustment. If the clock pulse is not set correctly, some vertical bars appear on the screen.
DDC/CI (Display Data Channel / Command Interface)
VESA provides the standardization for the interactive communication of the setting information, etc.
between a PC and the monitor.
DisplayPort
DisplayPort is a next-generation digital AV interface that allows connection of the PC, audio, imaging
devices, etc. to the monitor. One cable can transfer sound with images.
DVI (Digital Visual Interface)
DVI is a digital interface standard. DVI allows direct transmission of the PC’s digital data without loss.
This adopts the TMDS transmission system and DVI connectors. There are two types of DVI connectors.
One is a DVI-D connector for digital signal input only. The other is a DVI-I connector for both digital and
analog signal inputs.
DVI DMPM (DVI Digital Monitor Power Management)
DVI DMPM is a digital interface power saving function. The “Monitor ON (operating mode)” and “Active
Off (power saving mode)” are indispensable for DVI DMPM as the monitor’s power mode.
Gain
This is used to adjust each color parameter for red, green and blue. An LCD monitor displays the color by
the light passing through the panel color filter. Red, green and blue are the three primary colors. All the
colors on the screen are displayed by combining these three colors. The color tone can be changed by
adjusting the light intensity (volume) passing through each color’s filter.
Gamma
Generally, the monitor brightness varies nonlinearly with the input signal level, which is called “Gamma
Characteristic”. A small gamma value produces a low-contrast image, while a large gamma value produces a
high-contrast image.
HDCP (High-bandwidth Digital Content Protection)
Digital signal coding system developed to copy-protect the digital contents, such as video, music, etc.
This helps to transmit the digital contents safely by coding the digital contents sent via the DVI or HDMI
connector on the output side and decoding them on the input side.
Any digital contents cannot be reproduced if both of the equipments on the output and input sides are not
applicable to HDCP system.
64
Chapter 6 Reference
Overdrive
This technology enhances response speed by increasing the potential difference at the time of motion of
liquid-crystal pixels, and it is used for liquid-crystal TV sets and others in general. It provides clear-cut
three-dimensional display with little afterimage, by improving response speed of the intermediate graduation
range that frequently appears in moving images.
Phase
Phase means the sampling timing to convert the analog input signal to a digital signal. Phase adjustment is
made to adjust the timing. It is recommended that phase adjustment be made after the clock is adjusted
correctly.
Range Adjustment
Range adjustment controls the signal output levels to display every color gradation. It is recommended that
range adjustment be made before color adjustment.
Resolution
The LCD panel consists of numerous pixels of specified size, which are illuminated to form images. This
monitor consists of horizontal 1920 pixels and 1080 vertical pixels (EV2316W / EV2336W), or horizontal
1920 pixels and 1200 vertical pixels (EV2416W / EV2436W). At a resolution of 1920 × 1080 (EV2316W /
EV2336W) or 1920 × 1200 (EV2416W / EV2436W), all pixels are illuminated as a full screen (1:1).
sRGB (Standard RGB)
International standard for color reproduction and color space among peripheral devices (such as monitors,
printers, digital cameras, scanners). As a form of simple color matching for the Internet, colors can be
displayed using tones close to those of the transmission and reception devices.
Temperature
Color temperature is a method to measure the white color tone, generally indicated in degrees Kelvin. The
screen becomes reddish at a low temperature, and bluish at a high temperature, like the flame temperature.
5000 K: Slightly reddish white
6500 K: White referred to as daylight-balanced color
9300 K: Slightly bluish white
TMDS (Transition Minimized Differential Signaling)
A signal transmission system for digital interface.
VESA DPM (Video Electronics Standards Association - Display Power
Management)
VESA specifications achieve increased energy efficiency for computer monitors. This involves
standardization of signals sent from the computer (graphics board).
DPM defines the status of signals transmitted between the computer and monitor.
Chapter 6 Reference
65
Appendix
Trademark
The DisplayPort Compliance Logo and VESA are registered trademarks of the Video Electronics Standards
Association.
Windows, Windows Vista, Windows Media, SQL Server, and Xbox 360 are registered trademarks of Microsoft
Corporation in the United States and other countries.
Apple, Mac, Macintosh, iMac, eMac, Mac OS, MacBook, PowerBook, ColorSync, QuickTime, and iBook are
registered trademarks of Apple Inc.
Acrobat, Adobe, Adobe AIR, and Photoshop are registered trademarks of Adobe Systems Incorporated in the
United States and other countries.
PowerPC is a registered trademark of International Business Machines Corporation.
Pentium is a registered trademark of Intel Corporation in the United States and other countries.
AMD Athlon and AMD Opteron are trademarks of Advanced Micro Devices, Inc.
GRACoL and IDEAlliance are registered trademarks of International Digital Enterprise Alliance.
ColorVision, ColorVision Spyder2 are registered trademarks of DataColor Holding AG.
Spyder3 is a trademark of DataColor Holding AG.
Eye-One, ColorMunki, and X-Rite are registered trademarks or trademarks of X-Rite Incorporated.
TouchWare is a trademark of 3M Touch Systems, Inc.
NextWindow is a registered trademark of NextWindow Ltd.
RealPlayer is a registered trademark of RealNetworks, Inc.
NEC is a registered trademark of NEC Corporation. PC-9801 and PC-9821 are trademarks of NEC Corporation.
PlayStation is a registered trademark of Sony Computer Entertainment Inc.
PSP and PS3 are trademarks of Sony Computer Entertainment Inc.
ENERGY STAR is a registered trademark of the United States Environmental Protection Agency in the United
States and other countries.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or
registered trademarks of HDMI Licensing, LLC in the United States and other countries.
Kensington and MicroSaver are trademarks of ACCO Brands Corporation.
EIZO, the EIZO Logo, ColorEdge, DuraVision, FlexScan, FORIS, RadiForce, RadiCS, RadiNET, Raptor, and
ScreenManager are registered trademarks of EIZO Corporation in Japan and other countries.
ColorNavigator, EIZO EasyPIX, EcoView NET, EIZO ScreenSlicer, i • Sound, Screen Administrator, and UniColor
Pro are trademarks of EIZO Corporation.
All other company and product names are trademarks or registered trademarks of their respective owners.
License
A round gothic bold bit map font designed by Ricoh is used for the characters displayed on this product.
66
Appendix
ENERGY STAR
As an ENERGY STAR Partner, EIZO Corporation has determined that this product meets the
ENERGY STAR guidelines for energy efficiency.
TCO
This product has acquired the TCO standard that relates to the safety, ergonomics (EcoView Optimizer 2: Off),
environment and so forth of office equipment. For an overview of the TCO, refer to our web site.
http://www.eizo.com
Appendix
67
FCC Declaration of Conformity
For U.S.A. , Canada, etc. (rated 100-120 Vac) Only
FCC Declaration of Conformity
We, the Responsible Party
EIZOInc.
5710WarlandDrive,Cypress,CA90630
Phone:(562)431-5011
declare that the product
Tradename:EIZO
Model:FlexScanEV2316W/EV2336W/EV2416W/EV2436W
is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,pursuant
toPart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainst
harmfulinterferenceinaresidentialinstallation.Thisequipmentgenerates,uses,andcanradiateradio
frequencyenergyand,ifnotinstalledandusedinaccordancewiththeinstructions,maycauseharmful
interferencetoradiocommunications.However,thereisnoguaranteethatinterferencewillnotoccurin
aparticularinstallation.Ifthisequipmentdoescauseharmfulinterferencetoradioortelevisionreception,
whichcanbedeterminedbyturningtheequipmentoffandon,theuserisencouragedtotrytocorrect
theinterferencebyoneormoreofthefollowingmeasures.
* Reorientorrelocatethereceivingantenna.
* Increasetheseparationbetweentheequipmentandreceiver.
* Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected.
* Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
Changesormodificationsnotexpresslyapprovedbythepartyresponsibleforcompliancecouldvoidthe
user’sauthoritytooperatetheequipment.
Note
UsetheattachedspecifiedcablebeloworEIZOsignalcablewiththismonitorsoastokeepinterference
withinthelimitsofaClassBdigitaldevice.
- ACCord
- ShieldedSignalCable(enclosed)
Canadian Notice
ThisClassBdigitalapparatuscomplieswithCanadianICES-003.
CetappareilnumériquedeleclasseBestcomformeàlanormeNMB-003duCanada.
68
Appendix
Hinweise zur Auswahl des richtigen Schwenkarms für Ihren Monitor
Dieser Monitor ist für Bildschirmarbeitsplätze vorgesehen. Wenn nicht der zum Standardzubehör gehörige
Schwenkarm verwendet wird, muss statt dessen ein geeigneter anderer Schwenkarm installiert werden. Bei der
Auswahl des Schwenkarms sind die nachstehenden Hinweise zu berücksichtigen:
Der Standfuß muß den nachfolgenden Anforderungen entsprechen:
a) Der Standfuß muß eine ausreichende mechanische Stabilität zur Aufnahme des Gewichtes vom Bildschirmgerät
und des spezifizierten Zubehörs besitzen. Das Gewicht des Bildschirmgerätes und des Zubehörs sind in der
zugehörenden Bedienungsanleitung angegeben.
b)Die Befestigung des Standfusses muß derart erfolgen, daß die oberste Zeile der Bildschirmanzeige nicht höher
als die Augenhöhe eines Benutzers in sitzender Position ist.
c) Im Fall eines stehenden Benutzers muß die Befestigung des Bildschirmgerätes derart erfolgen, daß die Höhe der
Bildschirmmitte über dem Boden zwischen 135 – 150 cm beträgt.
d)Der Standfuß muß die Möglichkeit zur Neigung des Bildschirmgerätes besitzen (max. vorwärts: 5°, min. nach
hinten ≥ 5°).
e) Der Standfuß muß die Möglichkeit zur Drehung des Bildschirmgerätes besitzen (max. ±180°). Der maximale
Kraftaufwand dafür muß weniger als 100 N betragen.
f) Der Standfuß muß in der Stellung verharren, in die er manuell bewegt wurde.
g)Der Glanzgrad des Standfusses muß weniger als 20 Glanzeinheiten betragen (seidenmatt).
h)Der Standfuß mit Bildschirmgerät muß bei einer Neigung von bis zu 10° aus der normalen aufrechten Position
kippsicher sein.
Hinweis zur Ergonomie :
Dieser Monitor erfüllt die Anforderungen an die Ergonomie nach EK1-ITB2000 mit dem Videosignal, 1920×1080
(EV2316W / EV2336W) / 1920×1200 (EV2416W / EV2436W), Digital Eingang und mindestens 60,0 Hz
Bildwiederholfrequenz, non interlaced. Weiterhin wird aus ergonomischen Gründen empfohlen, die Grundfarbe
Blau nicht auf dunklem Untergrund zu verwenden (schlechte Erkennbarkeit, Augenbelastung bei zu geringem
Zeichenkontrast.)
Übermäßiger Schalldruck von Ohrhörern bzw. Kopfhörern kann einen Hörverlust bewirken.
Eine Einstellung des Equalizers auf Maximalwerte erhöht die Ausgangsspannung am Ohrhörer- bzw.
Kopfhörerausgang und damit auch den Schalldruckpegel.
„Maschinenlärminformations-Verordnung 3. GPSGV:
Der höchste Schalldruckpegel beträgt 70 dB(A) oder weniger gemäss EN ISO 7779“
[Begrenzung des maximalen Schalldruckpegels am Ohr]
Bildschirmgeräte: Größte Ausgangsspannung 150 mV
Appendix
69
LIMITED WARRANTY
LIMITED WARRANTY
EIZOCorporation(hereinafterreferredtoas“EIZO”)anddistributorsauthorizedbyEIZO(hereinafterreferredtoasthe
“Distributors”)warrant,subjecttoandinaccordancewiththetermsofthislimitedwarranty(hereinafterreferredtoasthe
“Warranty”),totheoriginalpurchaser(hereinafterreferredtoasthe“Original Purchaser”)whopurchasedtheproduct
specifiedinthisdocument(hereinafterreferredtoasthe“Product”)fromEIZOorDistributors,thatEIZOandDistributors
shall,attheirsolediscretion,eitherrepairorreplacetheProductatnochargeiftheOriginalPurchaserbecomesaware
withintheWarrantyPeriod(definedbelow)thattheProductmalfunctionsorisdamagedinthecourseofnormaluseof
theProductinaccordancewiththedescriptionintheinstructionmanualattachedtotheProduct(hereinafterreferredto
asthe“User’s Manual”).
The period of this Warranty is limited to (i) five (5) years from the date of purchase of the Product; or, limited to the
expiration of (ii) 30,000 hours of its use of the Product(hereinafterreferredtoasthe“Warranty Period”).EIZOand
DistributorsshallbearnoliabilityorobligationwithregardtotheProductinrelationtotheOriginalPurchaseroranythird
partiesotherthanasprovidedunderthisWarranty.
EIZOandDistributorswillceasetoholdorstoreanypartsoftheProductuponexpirationofseven(7)yearsafterthe
productionofsuchpartsisdiscontinued.Inrepairingthemonitor,EIZOandDistributorswilluserenewalpartswhich
complywithourQCstandards.
TheWarrantyisvalidonlyinthecountriesorterritorieswheretheDistributorsarelocated.TheWarrantydoesnotrestrict
anylegalrightsoftheOriginalPurchaser.
NotwithstandinganyotherprovisionofthisWarranty,EIZOandDistributorsshallhavenoobligationunderthisWarranty
whatsoeverinanyofthecasesassetforthbelow:
(a) AnydefectoftheProductcausedbyfreightdamage,modification,alteration,abuse,misuse,accident,incorrect
installation,disaster,faultymaintenanceand/orimproperrepairbythirdpartyotherthanEIZOandDistributors;
(b) AnyincompatibilityoftheProductduetopossibletechnicalinnovationsand/orregulations;
(c) Anydeteriorationofthesensor;
(d) AnydeteriorationofdisplayperformancecausedbythedeteriorationofexpendablepartssuchastheLCDpanel
and/orbacklight,etc.(e.g.changesinbrightness,changesinbrightnessuniformity,changesincolor,changesin
coloruniformity,defectsinpixelsincludingburntpixels,etc.);
(e) AnydefectoftheProductcausedbyexternalequipment;
(f) AnydefectoftheProductonwhichtheoriginalserialnumberhasbeenalteredorremoved;
(g) Anynormaldeteriorationoftheproduct,particularlythatofconsumables,accessories,and/orattachments(e.g.
buttons,rotatingparts,cables,User’sManual,etc.);and
(h) Anydeformation,discoloration,and/orwarpoftheexterioroftheproductincludingthatofthesurfaceoftheLCD
panel.
To obtain service under the Warranty, the Original Purchaser must deliver the Product, freight prepaid, in its original
packageorotheradequatepackageaffordinganequaldegreeofprotection,assumingtheriskofdamageand/orloss
intransit,tothelocalDistributor.TheOriginalPurchasermustpresentproofofpurchaseoftheProductandthedateof
suchpurchasewhenrequestingservicesundertheWarranty.
TheWarrantyPeriodforanyreplacedand/orrepairedproductunderthisWarrantyshallexpireattheendoftheoriginal
WarrantyPeriod.
EIZO OR DISTRIBUTORSARE NOT RESPONSIBLE FORANY DAMAGE TO, OR LOSS OF, DATA OR OTHER
INFORMATIONSTOREDINANYMEDIAORANYPARTOFANYPRODUCTRETURNEDTOEIZOORDISTRIBUTORS
FORREPAIR.
EIZOAND DISTRIBUTORS MAKE NO FURTHER WARRANTIES, EXPRESSED OR IMPLIED, WITH RESPECTTO
THE PRODUCTAND ITS QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FORANY PARTICULAR
USE. IN NO EVENT SHALL EIZO OR DISTRIBUTORS BE LIABLE FORANY INCIDENTAL, INDIRECT, SPECIAL,
CONSEQUENTIAL OR OTHER DAMAGE WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR
LOSSOFPROFIT,BUSINESSINTERRUPTION,LOSSOFBUSINESSINFORMATION,ORANYOTHERPECUNIARY
LOSS)ARISINGOUTOFTHEUSEORINABILITYTOUSETHEPRODUCTORINANYCONNECTIONWITHTHE
PRODUCT,WHETHERBASEDONCONTRACT,TORT,NEGLIGENCE,STRICTLIABILITYOROTHERWISE,EVEN
IFEIZOORDISTRIBUTORSHAVEBEENADVISEDOFTHEPOSSIBILITYOFSUCHDAMAGES.THISEXCLUSION
ALSO INCLUDESANY LIABILITY WHICH MAYARISE OUT OFTHIRD PARTY CLAIMSAGAINSTTHE ORIGINAL
PURCHASER. THE ESSENCE OF THIS PROVISION IS TO LIMIT THE POTENTIAL LIABILITY OF EIZOAND
DISTRIBUTORSARISINGOUTOFTHISLIMITEDWARRANTYAND/ORSALES.
70
Appendix
BEGRENZTE GARANTIE
EIZO Corporation (im Weiteren als „EIZO“ bezeichnet) und die Vertragsimporteure von EIZO (im Weiteren als
„Vertrieb(e)“bezeichnet)garantierendemursprünglichenKäufer(imWeiterenals„Erstkäufer“bezeichnet),derdasin
diesemDokumentvorgegebeneProdukt(imWeiterenals„Produkt“bezeichnet)vonEIZOodereinemVertrieberworben
hat,gemäßdenBedingungendieserbeschränktenGarantie(imWeiterenals„Garantie“bezeichnet),dassEIZOund
derVertriebnacheigenemErmessendasProduktentwederkostenlosreparierenoderaustauschen,fallsderErstkäufer
innerhalb der Garantiefrist (weiter unten festgelegt) eine Fehlfunktion bzw. Beschädigung des Produkts feststellt,
die während des normalen Gebrauchs des Produkts gemäß denAnweisungen des zum Lieferumfang des Produkts
gehörendenBenutzerhandbuchs(imWeiterenals„Benutzerhandbuch“bezeichnet)aufgetretenist.
Die Dauer der Garantieleistung beträgt (i) fünf (5) Jahre ab dem Erstverkaufsdatum des Produkts oder (ii) 30.000
BetriebsstundendesProdukts(imWeiterenals„Garantiefrist“bezeichnet).EIZOunddieVertriebeübernehmenüber
denRahmendieserGarantiehinaushinsichtlichdesProduktskeinerleiHaftungoderVerpflichtungdemErstkäuferoder
Drittengegenüber.
EIZOunddieVertriebeverpflichtensich,ErsatzteilefürdasProduktübereinenZeitraumvonsieben(7)Jahrennach
EinstellungderProduktionderErsatzteilezulagernbzw.anzubieten.EIZOundseineVertriebspartnerverpflichtensich,
beieineretwaigenReparaturdesMonitorsausschließlichProduktegemäßdenEIZO-Qualitätssicherungsstandardszu
verwenden.
Diese Garantie gilt nur in Ländern oder Gebieten, in denen sich Vertriebe befinden. Die gesetzlichen
GewährleistungsrechtedesErstkäufersgegenüberdemVerkäuferwerdendurchdieseGarantienichtberührt.
EIZOunddieVertriebebesitzenimRahmendieserGarantiekeinerleiVerpflichtungindenfolgendenFällen:
(a) Produktdefekte, die auf Frachtschäden, Modifikation, Nachgestaltung, Missbrauch, Fehlbedienung, Unfälle,
unsachgemäßeInstallation,Naturkatastrophen,fehlerhafteWartungund/oderunsachgemäßeReparaturdurcheine
andereParteialsEIZOunddieVertriebezurückzuführensind.
(b) Eine Inkompatibilität des Produkts aufgrund von technischen Neuerungen und/oder neuen Bestimmungen, die
nachdemKaufinKrafttreten.
(c) JeglicheVerschlechterungdesSensors.
(d) Jegliche Verschlechterung der Bildschirmleistung, die durch Verschleißteile wie das LCD-Panel und/oder die
Hintergrundbeleuchtungusw.hervorgerufenwerden(z.B.VeränderungenvonHelligkeitoderHelligkeitsverteilung,
VeränderungenvonFarbeoderFarbverteilung,PixeldefekteeinschließlichvondurchgebranntenPixelnusw.).
(e) Produktdefekte,diedurchexterneGeräteverursachtwerden.
(f) JeglicherDefekteinesProdukts,dessenursprünglicheSeriennummergeändertoderentferntwurde.
(g) NormaleAbnutzung des Produkts, insbesondere von Verbrauchsteilen, Zubehörteilen und/oder Beilagen (z.B.
Tasten,drehbareTeile,Kabel,Benutzerhandbuchusw.);sowie
(h) Verformungen,Verfärbungenund/oderVerziehungenamProduktäußeren,einschließlichderOberflächedesLCDPanels.
Bei Inanspruchnahme der Garantieleistung ist der Erstkäufer verpflichtet, das Produkt auf eigene Kosten und
in der Originalverpackung bzw. einer anderen geeigneten Verpackung, die einen gleichwertigen Schutz gegen
Transportschädenbietet,andenörtlichenVertriebzuübersenden,wobeiderErstkäuferdasTransportrisikogegenüber
Schädenund/oderVerlustträgt.ZumZeitpunktderInanspruchnahmederGarantieleistungmussderErstkäufereinen
Verkaufsbelegvorweisen,aufdemdasKaufdatumangegebenist.
DieGarantiefristfüreinimRahmendieserGarantieausgetauschtesund/oderrepariertesProdukterlischtnachAblauf
derursprünglichenGarantiefrist.
EIZOODERDIEEIZO-VERTRAGSIMPORTEUREHAFTENNICHTFÜRZERSTÖRTEDATENBESTÄNDEODERDIE
KOSTEN DER WIEDERBESCHAFFUNG DIESER DATENBESTÄNDEAUF JEGLICHEN DATENTRÄGERN ODER
TEILENDESPRODUKTS,DIEIMRAHMENDERGARANTIEBEIEIZOODERDENEIZO-VERTRAGSIMPORTEUREN
ZURREPARATUREINGEREICHTWURDEN.
EIZO UND DIE EIZO-VERTRAGSIMPORTEURE GEBEN WEDER EXPLIZITE NOCH IMPLIZITE GARANTIEN
IN BEZUGAUF DIESES PRODUKT UND SEINE QUALITÄT, LEISTUNG, VERKÄUFLICHKEIT ODER EIGNUNG
FÜR EINEN BESTIMMTEN ZWECK.AUF KEINEN FALL SIND EIZO ODER DIE EIZO-VERTRAGSIMPORTEURE
VERANTWORTLICH FÜR JEGLICHE ZUFÄLLIGE, INDIREKTE, SPEZIELLE, FOLGE- ODERANDERE SCHÄDEN
JEGLICHERART (EINSCHLIESSLICH OHNE JEDE BEGRENZUNG SCHÄDEN BEZÜGLICH PROFITVERLUST,
GESCHÄFTSUNTERBRECHUNG, VERLUST VON GESCHÄFTSINFORMATION ODER JEGLICHEANDEREN
FINANZIELLEN EINBUSSEN), DIE DURCH DIE VERWENDUNG DES PRODUKTES ODER DIE UNFÄHIGKEIT
ZUR VERWENDUNG DES PRODUKTES ODER IN JEGLICHER BEZIEHUNG MIT DEM PRODUKT, SEI ES
BASIERENDAUFVERTRAG,SCHADENSERSATZ,NACHLAESSIGKEIT,STRIKTEHAFTPFLICHTODERANDEREN
FORDERUNGEN ENTSTEHEN,AUCH WENN EIZO UND DIE EIZO-VERTRAGSIMPORTEURE IM VORAUS ÜBER
DIEMÖGLICHKEITSOLCHERSCHÄDENINFORMIERTWURDEN.DIESERAUSSCHLUSSENTHÄLTAUCHJEDE
HAFTPFLICHT, DIEAUS FORDERUNGEN DRITTER GEGEN DEN ERSTKÄUFER ENTSTEHEN KANN. ZWECK
DIESERKLAUSELISTES,DIEHAFTUNGVONEIZOUNDDENVERTRIEBENGEGENÜBERFORDERUNGENZU
BEGRENZEN,DIEAUSDIESERBESCHRÄNKTENGARANTIEUND/ODERDEMVERKAUFENTSTEHENKÖNNEN.
Appendix
71
GARANTIE LIMITÉE
EIZO Corporation (ci-après dénommé « EIZO ») et les distributeurs autorisés par EIZO (ci-après dénommés
« Distributeurs »), sous réserve et conformément aux termes de cette garantie limitée (ci-après dénommée
« Garantie »), garantissent à l’acheteur initial (ci-après dénommé « Acheteur initial ») du produit spécifié dans la
présente (ci-après dénommé « Produit ») acheté auprès d’EIZO ou de Distributeurs agréés EIZO, que EIZO et ses
DistributeursaurontpouroptionderéparerouremplacergratuitementleProduitsil’Acheteurinitialconstate,pendantla
Périodedegarantie(définieci-dessous),qu’ilyaundysfonctionnementouqueleProduitasubiundommagedansle
cadred’uneutilisationnormaleduProduitconformémentàladescriptiondumoded’emploiquiaccompagneleProduit
(ci-aprèsdénommé«Manuel d’utilisation »).
La période de cette Garantie est limitée à (i) cinq (5) ans à partir de la date d’achat du Produit ; ou, limitée jusqu’à
l’expirationde(ii)30000heuresd’utilisationduProduit(ci-aprèsdénommée« Période de Garantie»).EIZOetses
DistributeursdéclinenttouteresponsabilitéouobligationconcernantceProduitfaceàl’Acheteurinitialouàtouteautre
personneàl’exceptiondecellesstipuléesdanslaprésenteGarantie.
EIZO et ses Distributeurs cesseront de tenir ou conserver en stock toute pièce de ce Produit après l’expiration de
la période de sept (7) ans suivant l’arrêt de la production de telles pièces. Pour réparer le moniteur, EIZO et ses
distributeursutiliserontdespiècesderechangeconformesànosnormesdecontrôlequalité.
LaGarantieestvalableuniquementdanslespaysoulesterritoiresoùsetrouventlesDistributeurs.LaGarantienelimite
aucundesdroitsreconnusparlaloiàl’Acheteurinitial.
NonobstanttouteautreclausedecetteGarantie,EIZOetsesDistributeursn’aurontd’obligationdanslecadredecette
Garantiepouraucundescasénumérésci-dessous:
(a) ToutdéfautduProduitrésultantdedommagesoccasionnéslorsdutransport,d’unemodification,d’unealtération,
d’unabus,d’unemauvaiseutilisation,d’unaccident,d’uneinstallationincorrecte,d’undésastre,d’unentretienet/
oud’uneréparationincorrectseffectuésparunepersonneautrequeEIZOousesDistributeurs;
(b) TouteincompatibilitéduProduitrésultantd’améliorationstechniqueset/ouréglementationspossibles;
(c) Toutedétériorationducapteur;
(d) Toute détérioration des performances d’affichage causée par la détérioration des éléments consommables tels
quelepanneauLCDet/oulerétroéclairage,etc.(parexempledeschangementsdeluminosité,deschangements
del’uniformitédelaluminosité,desmodificationsdecouleur,deschangementsdel’uniformitédescouleurs,des
défectuositésdepixelsycomprisdespixelsbrûlés,etc.);
(e) ToutdéfautduProduitcauséparunappareilexterne;
(f) Toutdéfautd’unProduitsurlequellenumérodesérieoriginalaétéaltéréousupprimé;
(g) Toute détérioration normale du Produit, particulièrement celle des consommables, des accessoires et/ou des
piècesreliéesauProduit(touches,élémentspivotants,câbles,Manueld’utilisationetc.),et
(h) Toute déformation, décoloration, et/ou gondolage de l’extérieur du Produit, y compris celle de la surface du
panneauLCD.
Pourbénéficierd’unservicedanslecadredecetteGarantie,l’AcheteurinitialdoitrenvoyerleProduitportpayé,dans
sonemballaged’origineoutoutautreemballageappropriéoffrantundegrédeprotectionéquivalent,auDistributeurlocal,
etassumeralaresponsabilitédesdommageset/oupertepossibleslorsdutransport.L’Acheteurinitialdoitprésenterune
preuved’achatduProduitcomprenantsadated’achatpourbénéficierdeceservicedanslecadredelaGarantie.
LaPériodedegarantiepourtoutProduitremplacéet/ouréparédanslecadredecetteGarantieexpireraàlafindela
Périodedegarantieinitiale.
EIZOOUSESDISTRIBUTEURSNESAURAIENTÊTRETENUSRESPONSABLESDESDOMMAGESOUPERTESDE
DONNÉESOUD’AUTRESINFORMATIONSSTOCKÉESDANSUNMÉDIAQUELCONQUEOUUNEAUTREPARTIE
DUPRODUITRENVOYÉÀEIZOOUAUXDISTRIBUTEURSPOURRÉPARATION.
AUCUNEAUTRE GARANTIE, EXPLICITE OU TACITE, N’EST OFFERTE PAR EIZO ET SES DISTRIBUTEURS
CONCERNANT LE PRODUIT ET SES QUALITÉS, PERFORMANCES, QUALITÉ MARCHANDE OUADAPTATION
À UN USAGE PARTICULIER. ENAUCUN CAS, EIZO OU SES DISTRIBUTEURS NE SERONT RESPONSABLES
DES DOMMAGES FORTUITS, INDIRECTS, SPÉCIAUX, INDUITS, OU DE TOUTAUTRE DOMMAGE QUEL
QU’IL SOIT (Y COMPRIS, SANS LIMITATION, LES DOMMAGES RÉSULTANT D’UNE PERTE DE PROFIT, D’UNE
INTERRUPTION D’ACTIVITÉS, D’UNE PERTE DE DONNÉES COMMERCIALES, OU DETOUTAUTRE MANQUE
À GAGNER) RÉSULTANT DE L’UTILISATION OU DE L’INCAPACITÉ D’UTILISER LE PRODUIT OUAYANT UN
RAPPORTQUELCONQUEAVECLEPRODUIT,QUECESOITSURLABASED’UNCONTRAT,D’UNTORT,D’UNE
NÉGLIGENCE,D’UNERESPONSABILITÉSTRICTEOUAUTRE,MÊMESIEIZOOUSESDISTRIBUTEURSONTÉTÉ
AVERTISDELAPOSSIBILITÉDETELSDOMMAGES.CETTELIMITATIONINCLUTAUSSITOUTERESPONSABILITÉ
QUI POURRAIT ÊTRE SOULEVÉE LORS DES RÉCLAMATIONS D’UN TIERS CONTRE L’ACHETEUR INITIAL.
L’ESSENCE DE CETTE CLAUSE EST DE LIMITER LA RESPONSABILITÉ POTENTIELLE DE EIZO ET DE SES
DISTRIBUTEURSRÉSULTANTDECETTEGARANTIELIMITÉEET/OUDESVENTES.
72
Appendix
GARANTÍA LIMITADA
EIZO Corporation (en lo sucesivo “EIZO”) y sus distribuidores autorizados (en lo sucesivo los “Distribuidores”),
conarregloydeconformidadconlostérminosdeestagarantíalimitada(enlosucesivola“Garantía”),garantizanal
compradororiginal(enlosucesivoel“Comprador original”)quecompróelproductoespecificadoenestedocumento(en
losucesivoel“Producto”)aEIZOoasusDistribuidores,queEIZOysusDistribuidores,asupropiocriterio,repararán
osustituiránelProductodeformagratuitasielCompradororiginaldetectadentrodelperiododelaGarantía(indicado
posteriormente)queelProductonofuncionacorrectamenteoquesehaaveriadoduranteelusonormaldelmismode
acuerdoconlasindicacionesdelmanualdeinstruccionessuministradoconelProducto(enlosucesivoel“Manual del
usuario”).
ElperíododevalidezdeestaGarantíaestálimitadoa(i)cinco(5)añosapartirdelafechadecompradelProductoo(ii)
a30.000horasdeusodelProducto(enadelantedesignadocomoel“Periodo de Garantía”).EIZOysusDistribuidores
notendránningunaresponsabilidadniobligaciónconrespectoalProductoparaconelCompradororiginalniparacon
tercerosquenoseanlasestipuladasenlapresenteGarantía.
EIZOysusDistribuidoresnoestaránobligadosasuministrarcualquierrecambiodelProductounavezpasadossiete
(7)añosdesdequesedejedefabricarelmismo.Paralareparacióndelmonitor,EIZOylosdistribuidoresutilizarán
repuestosquecumplanconnuestrosestándaresdecontroldecalidad.
LaGarantíaesválidasóloenlospaísesyterritoriosdondeestánubicadoslosDistribuidores.LaGarantíanorestringe
ningúnderecholegaldelCompradororiginal.
A pesar de las estipulaciones de esta Garantía, EIZO y sus Distribuidores no tendrán obligación alguna bajo esta
Garantíaenningunodeloscasosexpuestosacontinuación:
(a) CualquierdefectodelProductocausadopordañoseneltransporte,modificación,alteración,abuso,usoincorrecto,
accidente, instalación incorrecta, desastre, mantenimiento incorrecto y/o reparación indebida realizada por un
terceroquenoseaEIZOosusDistribuidores.
(b) CualquierincompatibilidaddelProductodebidaaposiblesinnovacionestécnicasy/oreglamentaciones.
(c) Cualquierdeteriorodelsensor.
(d) Cualquierdeterioroenelrendimientodelavisualizacióncausadoporfallosenlaspiezasconsumiblescomoel
panelLCDy/ola"Backlight",etc.(p.ej.cambiosdebrillo,cambiosdeuniformidaddelbrillo,cambiosdecolor,
cambiosdeuniformidaddelcolor,defectosdepíxeles,incluyendopíxelesmuertos,etc.).
(e) CualquierdefectodelProductocausadoporunequipoexterno.
(f) CualquierdefectodelProductoenelquehayasidoalteradooborradoelnúmerodeserieoriginal.
(g) CualquierdeterioronormaldelProducto,yenparticulardelaspiezasconsumibles,accesoriosydemás(p.ej.
botones,piezasgiratorias,cables,Manualdelusuario,etc.).
(h) Cualquierdeformación,decoloracióny/oalabeodelexteriordelProductoincluidalasuperficiedelpanelLCD.
Para obtener servicio en los términos de esta Garantía, el Producto deberá ser enviado por el Comprador original,
asuDistribuidorlocal,coneltransportepreviamentepagado,enelembalajeoriginaluotroembalajeadecuadoque
ofrezcaelmismogradodeprotección,asumiendoelriesgodedañosy/opérdidadelProductoduranteeltransporte.El
CompradororiginaldeberápresentaruncomprobantedecompradelProductoenelquesereflejelafechadecompra
delmismocuandolosoliciteelserviciodeGarantía.
ElPeriododegarantíaparacualquierProductoreemplazadoy/oreparadoenlostérminosdeestaGarantíaexpiraráal
vencerelPeriododegarantíaoriginal.
EIZO O LOS DISTRIBUIDORESAUTORIZADOS DE EIZO NO SE RESPONSABILIZAN DE NINGÚN DAÑO O
PÉRDIDAQUEPUEDANSUFRIRLOSDATOSUOTRAINFORMACIÓNALMACENADAENCUALQUIERMEDIOO
CUALQUIERPARTEDECUALQUIERPRODUCTODEVUELTOAEIZOOALOSDISTRIBUIDORESDEEIZOPARA
SUREPARACIÓN.
EIZOY LOS DISTRIBUIDORESAUTORIZADOS DE EIZO NO OFRECEN NINGUNA OTRA GARANTÍA, IMPLÍCITA
NI EXPLÍCITA, CON RESPECTOAL PRODUCTO YA SU CALIDAD, RENDIMIENTO, COMERCIABILIDAD E
IDONEIDADPARACUALQUIERUSOENPARTICULAR.ENNINGÚNCASOSERÁNEIZOOLOSDISTRIBUIDORES
AUTORIZADOSDEEIZORESPONSABLESDENINGÚNDAÑOEMERGENTE,INDIRECTO,ESPECIAL,INHERENTE
O CUALQUIERA QUE SEA (INCLUYENDO, SIN LIMITACIÓN, DAÑOS POR LUCRO CESANTE, INTERRUPCIÓN
DE LAACTIVIDAD COMERCIAL, PÉRDIDA DE INFORMACIÓN COMERCIAL O CUALQUIER OTRA PÉRDIDA
PECUNIARIA)QUESEDERIVEDELUSOOIMPOSIBILIDADDEUSODELPRODUCTOOENRELACIÓNCONEL
PRODUCTO,YA SEA BASADO EN CONTRATO, PORAGRAVIO, NEGLIGENCIA, ESTRICTA RESPONSABILIDAD
O CUALQUIERA QUE SEA,AUN CUANDO SE HAYAADVERTIDOA EIZO OA LOS DISTRIBUIDORES DE EIZO
DELAPOSIBILIDADDETALESDAÑOS.ESTAEXCLUSIÓNTAMBIÉNABARCACUALQUIERRESPONSABILIDAD
QUE PUEDA DERIVARSE DE RECLAMACIONES HECHAS POR UN TERCERO CONTRA EL COMPRADOR
ORIGINAL.LAESENCIADEESTAESTIPULACIÓNESLIMITARLARESPONSABILIDADPOTENCIALDEEIZOYLOS
DISTRIBUIDORESQUEPUDIERADERIVARSEDEESTAGARANTÍALIMITADAY/OVENTAS.
Appendix
73
GARANZIA LIMITATA
EIZOCorporation(acuisifaràriferimentodaquiinpoicon“EIZO”)ediDistributoriautorizzatidaEIZO(acuisifarà
riferimento da qui in poi con “Distributori”) garantiscono, secondo i termini di questa garanzia limitata (a cui si farà
riferimentodaquiinpoicon“Garanzia”)all’acquirenteoriginale(acuisifaràriferimentodaquiinpoicon“Acquirente
originale”) che ha acquistato il prodotto specificato in questo documento (a cui si farà riferimento da qui in poi con
“Prodotto”)daEIZOodaisuoiDistributori,cheEIZOeidistributori,alorodiscrezione,riparerannoosostituirannoil
Prodottosenzaaddebitosel’Acquirenteoriginaletrova,entroilperiododellaGaranzia(definitosotto),cheilProdotto
malfunzionaesièdanneggiatonelcorsodelsuonormaleutilizzoosservandoleindicazionidelmanualediistruzioni
allegatoalProdotto(acuisifaràriferimentodaquiinpoicon“Manuale utente”).
LapresenteGaranziaèlimitataa(i)cinque(5)anniapartiredalladatad'acquistodelProdottoo(ii)alloscaderedi
30.000 ore d'utilizzo del Prodotto (a cui si farà riferimento da qui in poi con “Periodo di Garanzia”). EIZO e i suoi
DistributorinonsiassumonoalcunaresponsabilitàenonhannoalcunobbligoriguardoalProdottoversol'Acquirente
originaleoterzidiversidaquellirelativiaquestaGaranzia.
EIZO e i suoi Distributori cesseranno di tenere o di conservare qualsiasi ricambio del Prodotto allo scadere di sette
(7) anni dopo che la produzione di tali ricambi èstataterminata.Perlariparazionedelmonitor,EIZOeiDistributori
utilizzerannopartidiricambioconformiainostristandarddicontrollodellaqualità.
La Garanzia è valida soltanto nei paesi dove ci sono i Distributori EIZO. La Garanzia non limita alcun diritto legale
dell’Acquirenteoriginale.
IndipendentementedaqualsiasialtracondizionediquestaGaranzia,EIZOeisuoiDistributorinonavrannoalcunobbligo
derivantedaquestaGaranziainognunodeicasielencatidiseguito:
(a) QualsiasidifettodelProdottocausatodadanniditrasporto,modifiche,alterazioni,abusi,usiimpropri,incidenti,
installazioneerrata,calamità,manutenzioneerratae/oriparazioniimproprieeseguitedaterzepartichenonsiano
EIZOoisuoiDistributori.
(b) QualsiasiincompatibilitàdelProdottodovutaapossibiliinnovazionitecnichee/onormative.
(c) Qualsiasideterioramentodelsensore.
(d) Qualsiasideterioramentodelleprestazionidelloschermocausatodaldeterioramentodelleparticonsumabili,come
ilpannelloLCDe/olaretroilluminazione,ecc.(peresempio:icambiamentidiluminosità,cambiamentidiuniformità
della luminosità, i cambiamenti di colore, i cambiamenti di uniformità del colore, i difetti dei pixel, inclusi i pixel
bruciati,ecc.).
(e) QualsiasidifettodelProdottocausatodaapparecchiatureesterne.
(f) QualsiasidifettodelProdottoincuiilnumerodiserieoriginalesiastatoalteratoorimosso.
(g) Qualsiasi normale deterioramento del Prodotto, in particolar modo nelle sue parti di consumo, accessori, e/o
attacchi(peresempio:tasti,partirotanti,cavi,Manualedell’utente,ecc.).
(h) Qualsiasitipodideformazione,scolorimento,e/odiinvolucroesternodelProdottoinclusalasuperficiedelpannello
LCD.
Per ricevere assistenza tecnica con questa Garanzia, l’Acquirente originale deve inviare il Prodotto, con trasporto
pre-pagato, nella sua confezione originale o altraconfezioneadeguatachefornisceunlivelloanalogodiprotezione,
assumendosiilrischiodidannie/operditaintransito,alDistributorelocale.L’Acquirenteoriginaledevepresentarela
provadiacquistochestabilisceladatadiacquistodelProdottoquandorichiedeserviziosottoGaranzia.
IlPeriododigaranziaperqualsiasiProdottosostituitoe/oriparatosottoquestaGaranziascadeallafinedelPeriododi
garanziaoriginale.
EIZOOISUOIDISTRIBUTORINONSONORESPONSABILIPERQUALSIASIDANNOOPERDITADIDATIOALTRE
INFORMAZIONI MEMORIZZATI SU QUALSIASI SUPPORTO O QUALSIASI PARTE DI QUALSIASI PRODOTTO
INVIATOAEIZOOISUOIDISTRIBUTORIPERRIPARAZIONI.
EIZO E I SUOI DISTRIBUTORI NON OFFRONOALCUNA GARANZIAADDIZIONALE, IMPLICITA O ESPLICITA,
RIGUARDO IL PRODOTTO E LA SUA QUALITÀ, PRESTAZIONI, VENDIBILITÀ OAPPROPRIATEZZA PER
QUALSIASI USO PARTICOLARE. IN NESSUN CASO EIZO O I DISTRIBUTORI EIZOAUTORIZZATI SARANNO
RESPONSABILI PER QUALSIASI DANNOACCIDENTALE, INDIRETTO, SPECIALE, CONSEGUENTE O DI
QUALSIASIALTRANATURA(INCLUSI,SENZALIMITI,DANNIPERPERDITADIPROFITTI,INTERRUZIONEDELLE
ATTIVITÀ, PERDITA DI INFORMAZIONI D’AFFARI O QUALSIASIALTRA PERDITA PECUNIARIA) DERIVANTI
DALL’USO O DALL’IMPOSSIBILITÀ DI USARE IL PRODOTTO O IN QUALSIASI RELAZIONEAL PRODOTTO,
SIA SU BASE DI CONTRATTO, TORTO, NEGLIGENZA, STRETTA RESPONSABILITÀ OALTRIMENTI,ANCHE
SE EIZO O I DISTRIBUTORI EIZOAUTORIZZATI SONO STATIAVVERTITI DELLA POSSIBILITÀ DITALI DANNI.
QUESTAESCLUSIONEINCLUDEANCHEQUALSIASIRESPONSABILITÀCHEPOSSAINSORGEREDARECLAMI
DI TERZI CONTRO L’ACQUIRENTE ORIGINALE. L’ESSENZA DI QUESTO PROVVEDIMENTO È LIMITARE LA
RESPONSABILITÀPOTENZIALEDIEIZOEDEIDISTRIBUTORIDERIVANTEDAQUESTAGARANZIALIMITATAE/O
DALLEVENDITE.
74
Appendix
BEGRÄNSAD GARANTI
EIZOCorporation(nedankallat“EIZO”)ochEIZOsauktoriseradedistributörer(nedankallade“Distributörer”)garanterar
ienlighetmedvillkorenidennabegränsadegaranti(nedankallad“Garantin”)denursprungligeköparen(nedankallad
den“Ursprunglige köparen”)somköptedenidokumentetspecificeradeprodukten(nedankallad“Produkten”)från
EIZOellerDistributörer,attEIZOellerDistributörerenligtegetgottfinnandekostnadsfrittantingenrepareraellerbytaut
dendefektaProduktenomdenUrsprungligeköpareninomGarantiperioden(definierasnedan)upptäckerattProdukten
fungerarfelaktigtellerskadasundernormalanvändningavProduktenienlighetmedbeskrivningenibruksanvisningen
(nedankallad“Bruksanvisning”).
Giltighetsperiodenfördennagarantiärbegränsadtill(i)fem(5)årfråndatumetförProduktensinköpeller,omdetta
inträffartidigare,begränsattillutlöpandetav(ii)30000timmarsanvändningavProdukten(härikallad“Garantiperioden”).
EIZOochDistributörerskainteundernågravillkorhanågotannatansvaränvadsomangesidennagarantigällande
ProduktenirelationtilldenUrsprungligeköparenellertredjepart.
EIZOochDistributörerkommerattupphöramedlagerhållningavProduktensdelareftersju(7)årefterattproduktionen
av dessa delar upphört. Nät skärmen repareras använder EIZO och distributörer reservdelar som uppfyller våra
kvalitetsstandarder.
Garantin är endast giltig i de länder där det finns Distributörer. Garantin begränsar inte några av den Ursprunglige
köparenslagstadgaderättigheter.
OavsettandravillkoridennagarantiskainteEIZODistributörerundernågravillkorhanågotansvarinågotavdefall
sombeskrivsnedan:
(a) När någon bristfällighet hos Produkten kan härledas till att ha uppstått vid frakt, modifiering, ändring, felaktigt
handhavande,olycka,felaktiginstallation,katastrof,felaktigtunderhålloch/ellerfelaktigreparationutfördavtredje
partannanänEIZOochDistributörer.
(b) AllaformeravinkompatibilitethosProduktenpågrundavmöjligatekniskainnovationeroch/ellerbestämmelser.
(c) Allaförsämringaravsensorn.
(d) Alla försämringar av bildens prestanda beroende på förbrukningsdelar så som LCD-panel och/eller
bakgrundsbelysningetc.(t.ex.ändringariljusstyrka,jämnhetiljusstyrka,färg,färgjämnhet,defektapixlaroch/eller
fastlysandepixlaretc.).
(e) AlladefekterhosProduktensomorsakatsavexternutrustning.
(f) AlladefekterhosProduktenpåvilkendetursprungligaserienumretharändratselleravlägsnats.
(g) All normal försämring av Produkten, speciellt förbrukningsartiklar, tillbehör och/eller yttre delar (t.ex. knappar,
roterandedelar,kablar,Bruksanvisningenetc.).
(h) Varjedeformation,missfärgningoch/ellerskevhetavProduktensyttreinklusiveytanpåLCD-panelen.
För att erhålla service under denna garanti måste den Ursprunglige köparen (med hänseende till risken för skada
och/ellerförlustundertransport)levereraProduktentillnärmasteDistributörmedförebetaldfrakt,idessursprungliga
förpackning eller annan fullgod förpackning som ger likvärdigt skydd. Den Ursprunglige köparen måste kunna visa
inköpsbevisförProduktensomklargörProduktensinköpsdatumvidbegäranavgarantiservice.
Garantiperiodenförallautbyttaoch/ellerrepareradeprodukterunderdennagarantiskallupphöravidutgångenavden
ursprungligaGarantiperioden.
EIZOELLERDISTRIBUTÖRERÄRINTEANSVARIGAFÖRNÅGONFORMAVSKADAELLERFÖRLUSTAVDATA
ELLERANNAN INFORMATION SOM HAR LAGRATS I NÅGON FORMAV MEDIA ELLERANNAN DELAV NÅGON
PRODUKTSOMHARRETURNERATSTILLEIZOELLERDISTRIBUTÖRERFÖRREPARATION.
EIZO OCH DISTRIBUTÖRERNA GARANTERAR INGET, UTTRYCKLIGEN ELLER UNDERFÖRSTÅTT, VAD
BETRÄFFARPRODUKTENOCHDESSKVALITET,PRESTANDA,SÄLJBARHETELLERLÄMPLIGHETFÖRNÅGON
FORMAVSPECIELLANVÄNDNING.UNDERINGAOMSTÄNDIGHETERSKALLEIZOELLERDISTRIBUTÖRERNA
HÅLLASANSVARIGAFÖRNÅGRASOMHELSTUNDERORDNADE,INDIREKTA,SPECIELLA,DÄRAVFÖLJANDE
ELLER ÖVRIGA SKADOR (INKLUSIVE, UTAN BEGRÄNSNING TILL, SKADOR FÖR FÖRLUSTAV INKOMST,
AVBRUTENAFFÄRSRÖRELSE,FÖRLUSTAVAFFÄRSINFORMATIONELLERANNANSÄRSKILDFÖRLUST)SOM
UPPSTÅTT SOM ETT RESULTATAVANVÄNDNING ELLER OFÖRMÅGAATTANVÄNDA PRODUKTEN ELLER I
NÅGON FORMAVANSLUTNINGTILL PRODUKTERNA, VARE SIG DETTA GRUNDAS PÅ KONTRAKT, ÅTALBAR
HANDLING,FÖRSUMLIGHET,ANSVARSSKYLDIGHETELLERANNAT,ÄVENOMEIZOELLERDISTRIBUTÖRERNA
HAR INFORMERATS BETRÄFFANDE MÖJLIGHETATT SÅDANA SKADOR FÖRELIGGER. DETTA UNDANTAG
OMFATTARÄVENALLFORMAVANSVARSSKYLDIGHETSOMKANUPPSTÅGENOMENTREDJEPARTSANSPRÅK
GENTEMOTDENURSPRUNGLIGEKÖPAREN.GRUNDBESTÅNDSDELENIBESTÄMMELSENÄRATTBEGRÄNSA
DETEVENTUELLAANSVARSTAGANDETFÖREIZOOCHDISTRIBUTÖRERNASOMKANUPPSTÅGENOMDENNA
BEGRÄNSADEGARANTIOCH/ELLERFÖRSÄLJNING.
Appendix
75
ΠΕΡΙΟΡΙΣΜΕΝΗ ΕΓΓΥΗΣΗ
Η EIZO Corporation (στο εξής «EIZO») και οι διανομείς που εξουσιοδοτεί η EIZO (στο εξής «Διανομείς»)
παρέχουν εγγύηση, υποκείμενη και σύμφωνα με τους όρους της παρούσας περιορισμένης εγγύησης (στο εξής
«Εγγύηση»),στοναρχικόαγοραστή(στοεξής«Αρχικός Αγοραστής»)οοποίοςαγόρασετοπροϊόνπουκαθορίζεταιστο
παρόνέγγραφο(στοεξής«Προϊόν»)απότηνEIZOήτουςΔιανομείς,ηοποίαεξασφαλίζειότιηEIZOκαιοιΔιανομείς,
σύμφωναμετηδιακριτήευχέρειάτους,είτεθαεπισκευάσουνείτεθααντικαταστήσουντοΠροϊόνχωρίςχρέωσηεάνο
ΑρχικόςΑγοραστής αντιληφθεί εντός της ΠεριόδουΕγγύησης(ορίζεταικατωτέρω)ότιτοΠροϊόνδυσλειτουργείήέχει
υποστείβλάβηκατάτηδιάρκειακανονικήςχρήσηςτουΠροϊόντοςσύμφωναμετηνπεριγραφήστοεγχειρίδιοχρήσηςπου
συνοδεύειτοΠροϊόν(στοεξής«Εγχειρίδιο Χρήστη»).
ΗπερίοδοςτηςπαρούσαςΕγγύησηςείναι(i)πέντε(5)έτηαπότηνημερομηνίααγοράςτουΠροϊόντος,ή,στηλήξητων
(ii)30.000ωρώνχρήσηςτουΠροϊόντος(στοεξής«Περίοδος Εγγύησης»).ΗEIZOκαιοιΔιανομείςδενφέρουνκαμία
ευθύνηήυποχρέωσηόσοναφοράτοΠροϊόνσεσχέσημετονΑρχικόΑγοραστήήοποιοδήποτετρίτομέρος,ούτεάλλη
ευθύνηδιαφορετικήαπόαυτήνπουπαρέχεταιστηνπαρούσαΕγγύηση.
ΗEIZOκαιοιΔιανομείςθαπαύσουνναδιατηρούνήνααποθηκεύουντυχόνεξαρτήματατουΠροϊόντοςκατόπιντηςλήξης
τωνεπτά(7)ετώνμετάτηδιακοπήτηςπαραγωγήςτέτοιωνεξαρτημάτων.Κατάτηνεπισκευήτηςοθόνης,ηEIZOκαιοι
ΔιανομείςθαχρησιμοποιήσουνανταλλακτικάεπισκευήςπουσυμμορφώνονταιμεταπρότυπάμαςγιατηΔιασφάλιση
Ποιότητας.
Η Εγγύηση ισχύει μόνο σε χώρες ή περιοχές όπου βρίσκονται οιΔιανομείς. Η Εγγύηση δεν περιορίζει οποιαδήποτε
νόμιμαδικαιώματατουΑρχικούΑγοραστή.
ΛαμβανομένηςυπόψηκάθεδιάταξηςτηςπαρούσαςΕγγύησης,ηEIZOκαιοιΔιανομείςδενθαέχουνκαμίααπολύτως
υποχρέωσησύμφωναμετηνπαρούσαΕγγύησησεοποιαδήποτεαπότιςπεριπτώσειςπουδιατυπώνονταικατωτέρω:
(α) ΤυχόνελάττωματουΠροϊόντοςπουπροκαλείταιαπόζημιάκατάτημεταφορά,τροποποίηση,αλλαγή,κατάχρηση,
λανθασμένη χρήση, ατύχημα, λανθασμένηεγκατάσταση,καταστροφή,εσφαλμένησυντήρησηή/καιλανθασμένη
επισκευήαπότρίτομέροςεκτόςτηςEIZOκαιτωνΔιανομέων,
(β) ΤυχόνασυμβατότητατουΠροϊόντοςλόγωπιθανώντεχνικώνκαινοτομιώνή/καικανονισμών,
(γ) Τυχόνεπιδείνωσητουαισθητήρα,
(δ) Τυχόν επιδείνωση της απόδοσης οθόνης που προκαλείται από τη φθορά αναλώσιμων εξαρτημάτων όπως
της οθόνης LCD ή/και του φωτός υποβάθρου, κτλ. (π.χ. αλλαγές στη φωτεινότητα, αλλαγές στην ομοιομορφία
φωτεινότητας,αλλαγέςστοχρώμα,αλλαγέςστηνομοιομορφίαχρώματος,ελαττώματασεpixelπεριλαμβανομένων
τωνκαμένωνpixel,κτλ.),
(ε) ΤυχόνελάττωματουΠροϊόντοςπουπροκαλείταιαπόεξωτερικόεξοπλισμό,
(στ)ΤυχόνελάττωματουΠροϊόντοςστοοποίοέχειτροποποιηθείήαφαιρεθείογνήσιοςαριθμόςσειράς,
(ζ) Τυχόν φυσιολογική φθορά του προϊόντος, ιδιαίτερα αυτής των αναλώσιµων, των αξεσουάρ ή/και των
προσαρτηµάτων(π.χ.κουµπιά,περιστρεφόµεναµέρη,καλώδια,ΕγχειρίδιοΧρήστη,κτλ.),και
(η) Τυχόν παραμόρφωση, αποχρωματισμό ή/και διαστρέβλωση του εξωτερικού μέρους του προϊόντος,
περιλαμβανομένηςτηςεπιφάνειαςτηςοθόνηςLCD.
ΟΑρχικόςΑγοραστήςγιαναδικαιούταιυπηρεσίεςεπισκευήςσύμφωναμετηνΕγγύηση,θαπρέπειναπαραδώσειτο
Προϊόν, με πληρωμένα τα μεταφορικά έξοδα, στηναρχικήτουσυσκευασίαήσεάλληεπαρκήσυσκευασίαμεισότιμο
βαθμόπροστασίας,αναλαμβάνονταςτονκίνδυνοβλάβηςή/καιαπώλειαςκατάτημεταφορά,στοντοπικόΔιανομέα.Ο
ΑρχικόςΑγοραστήςότανζητάυπηρεσίεςεπισκευήςσύμφωναμετηνΕγγύηση,θαπρέπειναπροσκομίζειτηναπόδειξη
αγοράςτουΠροϊόντοςκαιτηνημερομηνίατηςαγοράς.
Η Περίοδος Εγγύησης για οποιοδήποτε αντικατεστημένο ή/και επισκευασμένο προϊόν σύμφωνα με την παρούσα
ΕγγύησηλήγειστοτέλοςτηςαρχικήςΠεριόδουΕγγύησης.
Η EIZO Ή ΟΙΔΙΑΝΟΜΕΙΣΔΕΝ ΕΥΘΥΝΟΝΤΑΙ ΓΙΑ ΟΠΟΙΑΔΗΠΟΤΕ ΒΛΑΒΗ ΉΑΠΩΛΕΙΑΔΕΔΟΜΕΝΩΝ ΉΑΛΛΩΝ
ΠΛΗΡΟΦΟΡΙΩΝ ΠΟΥΑΠΟΘΗΚΕΥΟΝΤΑΙ ΣΕ ΟΠΟΙΟΔΗΠΟΤΕ ΜΕΣΟ Ή ΟΠΟΙΟΔΗΠΟΤΕΑΛΛΟ ΜΕΡΟΣ ΣΕ
ΟΠΟΙΟΔΗΠΟΤΕΠΡΟΪΟΝΠΟΥΕΠΙΣΤΡΕΦΕΤΑΙΣΤΗΝEIZOΉΣΕΔΙΑΝΟΜΕΑΓΙΑΕΠΙΣΚΕΥΗ.
Η EIZO ΚΑΙ ΟΙΔΙΑΝΟΜΕΙΣΔΕΝ ΠΑΡΕΧΟΥΝ ΚΑΜΙΑ ΠΕΡΑΙΤΕΡΩ ΕΓΓΥΗΣΗ, ΡΗΤΗ Ή ΣΥΝΕΠΑΓΟΜΕΝΗ, ΟΣΟΝ
ΑΦΟΡΑΤΟ ΠΡΟΪΟΝ ΚΑΙΤΗΝ ΠΟΙΟΤΗΤΑ,ΤΗΝΑΠΟΔΟΣΗ,ΤΗΝ ΕΜΠΟΡΕΥΣΙΜΟΤΗΤΑ ΉΤΗΝ ΚΑΤΑΛΛΗΛΟΤΗΤΑ
ΤΟΥ ΓΙΑ ΟΠΟΙΑΔΗΠΟΤΕ ΣΥΓΚΕΚΡΙΜΕΝΗ ΧΡΗΣΗ. ΣΕ ΚΑΜΙΑ ΠΕΡΙΠΤΩΣΗ Η EIZO Ή ΟΙΔΙΑΝΟΜΕΙΣΔΕΝ
ΘΑ ΕΥΘΥΝΟΝΤΑΙ ΓΙΑ ΚΑΜΙΑΑΠΟΛΥΤΩΣ ΤΥΧΑΙΑ, ΕΜΜΕΣΗ, ΕΙΔΙΚΗ, ΣΥΝΕΠΑΓΟΜΕΝΗ ΉΑΛΛΗ ΒΛΑΒΗ
(ΠΕΡΙΛΑΜΒΑΝΟΜΕΝΩΝ, ΜΕΤΑΞΥΑΛΛΩΝ, ΒΛΑΒΩΝ ΉΑΠΩΛΕΙΑΣ ΚΕΡΔΩΝ,ΔΙΑΚΟΠΗΣ ΕΠΙΧΕΙΡΗΜΑΤΙΚΩΝ
ΔΡΑΣΤΗΡΙΟΤΗΤΩΝ,ΑΠΩΛΕΙΑΣΕΠΙΧΕΙΡΗΜΑΤΙΚΩΝΠΛΗΡΟΦΟΡΙΩΝΉΤΥΧΟΝΑΛΛΗΣΧΡΗΜΑΤΙΚΗΣΑΠΩΛΕΙΑΣ)
ΠΟΥΠΡΟΚΥΠΤΕΙΑΠΟΤΗΧΡΗΣΗΉΤΗΝΑΝΙΚΑΝΟΤΗΤΑΧΡΗΣΗΣΤΟΥΠΡΟΪΟΝΤΟΣΉΤΥΧΟΝΑΛΛΗΣΣΥΝΔΕΣΗΣ
ΜΕΤΟΠΡΟΪΟΝ,ΕΙΤΕΒΑΣΙΖΕΤΑΙΣΕΣΥΜΒΟΛΑΙΟ,ΒΛΑΒΗ,ΑΜΕΛΕΙΑ,ΑΥΣΤΗΡΗΕΥΘΥΝΗΉΕΙΔΑΛΛΩΣ,ΑΚΟΜΗ
ΚΙΕΑΝΗEIZOΉΟΙΔΙΑΝΟΜΕΙΣΕΝΗΜΕΡΩΘΟΥΝΓΙΑΤΗΝΠΙΘΑΝΟΤΗΤΑΤΕΤΟΙΩΝΖΗΜΙΩΝ.ΗΕΞΑΙΡΕΣΗΑΥΤΗ
ΠΕΡΙΛΑΜΒΑΝΕΙ ΕΠΙΣΗΣ ΟΠΟΙΑΔΗΠΟΤΕ ΕΥΘΥΝΗΕΝΔΕΧΕΤΑΙΝΑΠΡΟΚΥΨΕΙΑΠΟΑΞΙΩΣΕΙΣΤΡΙΤΟΥΜΕΡΟΥΣ
ΚΑΤΑΤΟΥΑΡΧΙΚΟΥΑΓΟΡΑΣΤΗ. Η ΟΥΣΙΑΤΟΥΟΡΟΥΑΥΤΟΥΕΙΝΑΙΝΑΠΕΡΙΟΡΙΣΕΙΤΗΝΠΙΘΑΝΗΕΥΘΥΝΗΤΗΣ
EIZOΚΑΙΤΩΝΔΙΑΝΟΜΕΩΝΠΟΥΠΡΟΚΥΠΤΕΙΑΠΟΤΗΝΠΑΡΟΥΣΑΕΓΓΥΗΣΗΉ/ΚΑΙΤΙΣΠΩΛΗΣΕΙΣ.
76
Appendix
ОГРАНИЧЕННАЯ ГАРАНТИЯ
EIZO Corporation (называемая в дальнейшем “EIZO”) и авторизированные EIZO дистрибуторы (называемые в
дальнейшем“Дистрибуторы”)гарантируют,всоответствиисусловиямиипунктамиэтойограниченнойгарантии
(называемойвдальнейшем“Гарантия”),первичномупокупателю(называемомувдальнейшем“Первоначальный
покупатель”),которыйприобрелуEIZOилиДистрибуторовпродукт,указанныйвэтомдокументе(называемый
в дальнейшем “Продукт”), что EIZO или Дистрибуторы на свое усмотрение либо бесплатно отремонтируют,
либо бесплатно заменят Продукт, если Первоначальный покупатель признает в пределах Гарантийного срока
(определенногониже),чтоПродуктнеисправенилионповрежденпроцессенормальногоиспользованияпродукта
всоответствиисописаниемвинструкциипоэксплуатации,прилагаемойкПродукту(называемойвдальнейшем
“Руководство пользователя”).
Гарантийный период ограничен сроком (i) пять (5) лет от даты приобретения Продукта или ограничен сроком
(ii) 30 000 часов использования Продукта (называемый в дальнейшем “Гарантийный период”). EIZO и
ДистрибуторыненесутникакойответственностиинеберутобязательствотносительноПродуктапоотношениюк
Первоначальномупокупателюилипоотношениюклюбымтретьимсторонам,кромеобязательств,оговоренныхв
этойГарантии.
EIZOиДистрибуторыпрекратятхранениеилискладированиелюбыхдеталейПродуктапоистечениисеми(7)
летпослепрекращенияпроизводстватакихдеталей.ВслучаеремонтамонитораEIZOиДистрибьюторыбудут
использоватьзапчасти,которыесоответствуютнашимстандартамQC(контролькачества).
Гарантия действительна только в странах или регионах, где расположены Дистрибуторы. Гарантия не
ограничиваетникакиезаконныеправаПервоначальногопокупателя.
НесмотрянадругиеусловияэтойГарантииEIZOиДистрибуторыненесутникакихобязательствсогласноэтой
Гарантиивлюбомизперечисленныхнижеслучаев:
(а) Любые дефекты Продукта, вызванные повреждениями при перевозке, модификацией, изменением,
неправильным обращением, неправильным использованием, авариями, неправильной установкой,
стихийнымибедствиями,неправильнымуходоми/илинеправильнымремонтомтретьейстороной,отличной
отEIZOилиДистрибуторов;
(б) Любые несовместимости Продукта из-за технических усовершенствований и/или изменения технических
норм;
(в) Любоеповреждениедатчика;
(г) Любые ухудшения работы дисплея, вызванные изнашиванием невосстановимых частей, таких как
панельЖКДи/илиподсветкаит.д.(например,изменениевяркости,изменениевравномерностияркости,
изменениевцветности,изменениевравномерностицветности,изменениевпикселах,включаявыгоревшие
пикселыит.д.);
(д) ЛюбыедефектыПродукта,вызванныевнешнимоборудованием;
(е) ЛюбыедефектыПродукта,прикоторыхоригинальныйсерийныйномербылизмененилиудален;
(ж) Любые естественные ухудшения продукта, в частности, вызванные износом расходных частей,
принадлежностей и/или приспособлений (например, кнопок, вращающихся частей, кабелей, Руководства
пользователяит.д.);и
(з) Любые деформации, изменения цвета и/или коробления внешней поверхности продукта, включая
поверхностьпанелиЖКД.
Чтобы получить техническое обслуживание в рамках Гарантии, Первоначальный покупатель должен доставить
Продукт местному Дистрибутору, оплатив перевозку, в его оригинальной упаковке или в другой соответствующей
упаковке,обеспечивающейравноценнуюстепеньзащиты,принимаявовниманиерискповрежденияи/илиутерюпри
транспортировке. При запросе технического обслуживания в рамках Гарантии Первоначальный покупатель должен
предоставитьсвидетельствопокупкипродуктаидатыпокупки.
Гарантийныйпериоддлялюбогозамененногои/илиотремонтированногопродуктаврамкахГарантииистекаетвконце
завершениясрокадействияоригинальногоГарантийногопериода.
EIZOИЛИДИСТРИБУТОРЫНЕНЕСУТОТВЕТСТВЕННОСТИЗАЛЮБЫЕПОВРЕЖДЕНИЯИЛИУТЕРЮДАННЫХИЛИ
ДРУГОЙ ИНФОРМАЦИИ, ХРАНЯЩИХСЯ НА КАКИХ-ЛИБО НОСИТЕЛЯХ ИНФОРМАЦИИ ИЛИ НА ЛЮБЫХ ДРУГИХ
ЧАСТЯХПРОДУКТА,КОТОРЫЙВОЗВРАЩЕНEIZOИЛИДИСТРИБУТОРАМДЛЯРЕМОНТА.
EIZOИДИСТРИБУТОРЫНЕДАЮТНИКАКОЙДАЛЬНЕЙШЕЙГАРАНТИИ,ВЫРАЖЕННОЙИЛИПОДРАЗУМЕВАЕМОЙ,
ОТНОСИТЕЛЬНО ПРОД УКТА И ЕГО КАЧЕСТВА, ТЕХНИЧЕСКИХ ХАРАКТЕРИСТИК, ТОВАРНОСТИ ИЛИ
СООТВЕТСТВИЯ ДЛЯ КАКОГО-ЛИБО ОПРЕДЕЛЕННОГО ИСПОЛЬЗОВАНИЯ. НИ ПРИ КАКИХ УСЛОВИЯХ EIZO
ИЛИ ДИСТРИБУТОРЫ НЕ НЕСУТ ОТВЕТСТВЕННОСТИ ЗА ЛЮБОЙ СЛУЧАЙНЫЙ, КОСВЕННЫЙ, СПЕЦИАЛЬНЫЙ,
ПОБОЧНЫЙ ИЛИ ИНОЙ УЩЕРБ (ВКЛЮЧАЯ, БЕЗ ОГРАНИЧЕНИЙ, УЩЕРБ ИЗ-ЗА НЕПОЛУЧЕННОЙ ПРИБЫЛИ,
ПРЕРЫВАНИЯ БИЗНЕСА, ПОТЕРИ КОММЕРЧЕСКОЙ ИНФОРМАЦИИ ИЛИ ЛЮБЫЕ ДРУГИЕ ФИНАНСОВЫЕ
ПОТЕРИ), ВОЗНИКШИЙ ИЗ-ЗА ИСПОЛЬЗОВАНИЯ ИЛИ НЕВОЗМОЖНОСТИ ИСПОЛЬЗОВАТЬ ПРОДУКТ ИЛИ В
ЛЮБОЙДРУГОЙСВЯЗИСПРОДУКТОМ,ЛИБООСНОВАННЫЙНАКОНТРАКТНЫХОТНОШЕНИЯХ,ГРАЖДАНСКИХ
ПРАВОНАРУШЕНИЯХ, НЕБРЕЖНОСТИ, ПРИЧИНЕНИЯ УЩЕРБА ТРЕТЬЕЙ СТОРОНЕ ИЛИ ЧЕМ-ЛИБО ЕЩЕ, ДАЖЕ
ЕСЛИ EIZO ИЛИ ДИСТРИБУТОРЫ БЫЛИ УВЕДОМЛЕНЫ О ВОЗМОЖНОСТИ ТАКОГО УЩЕРБА. ЭТО ИСКЛЮЧЕНИЕ
ТАКЖЕ ВКЛЮЧАЕТ ЛЮБЫЕ ОБЯЗАТЕЛЬСТВА, КОТОРЫЕ МОГУТ ВОЗНИКНУТЬ В РЕЗУЛЬТАТЕ ТРЕБОВАНИЙ
ТРЕТЬЕЙ СТОРОНЫ В ОТНОШЕНИИ ПЕРВОНАЧАЛЬНОГО ПОКУПАТЕЛЯ. СУЩЕСТВОМ ЭТОГО ПОЛОЖЕНИЯ
ЯВЛЯЕТСЯОГРАНИЧЕНИЕПОТЕНЦИАЛЬНОЙОТВЕТСТВЕННОСТИEIZOИДИСТРИБУТОРОВ,ВОЗНИКАЮЩЕЙИЗЗАЭТОЙОГРАНИЧЕННОЙГАРАНТИИИ/ИЛИПРОДАЖ.
Appendix
77
有限责任保证书
EIZOCorporation(以下简称 EIZO )和 EIZO 授权的经销商(以下简称 经销商 ),接受并依照本有限责任保证书(以
下简称 保证书 )之条款,向从 EIZO 和经销商购买本文中所规定产品(以下简称 产品 )的原买方(以下称 原买方 )
提供保证 :在保证期内(规定如下),如果原买方发现按本产品所附使用说明书(以下简称 用户手册 )所述方式正常使
用本产品过程中,本产品出现故障或损坏,EIZO 和经销商根据其独自的判断免费修理或更换该产品。
本保证期限定为(i)自本产品购买之日起的五(5)年期间或限定为到达(ii)使用本产品 3 万小时的期限(以下简称 保证期限 )。
EIZO和经销商将不向原买方或任何第三方承担本保证书所规定之外的与本产品有关的任何责任或义务。
本产品的任何部件停产七 (7) 年后,EIZO 和经销商将不再保留或保管任何这类部件。维修显示器时,EIZO 与经销商将使
用符合我方质量控制标准的替换零件。
本保证书仅对于设有经销商的国家或地区有效。本保证书并不限定原买方的任何法律权利。
无论本保证书的任何其他条款如何规定,对于任何下列情况之一,EIZO 和经销商将不承担本保证书规定责任 :
(a) 由于运输损害、改装、改动、滥用、误用、意外事故、错误安装、灾害、维护不善和 / 或由除 EIZO 和经销商以外的
第三方进行不适当的修理造成本产品的任何故障。
(b) 由于可能发生的技术变更和 / 或调整造成本产品的任何不兼容性。
(c) 传感器的任何劣化。
(d) 由于诸如液晶显示屏(LCD)和 / 或背灯等消耗品部件的老化造成的任何显示性能低劣(如亮度变化、亮度均一性变化、
色彩变化、色彩均一性变化、如烧伤像素等像素缺陷)。
(e) 因外部设备造成本产品的任何故障。
(f) 因本产品的原序号被改变或消除造成本产品的任何故障。
(g) 本产品的任何正常老化,尤其是消耗品、附件和 / 或附加装置(如按钮、旋转部件、电缆、用户手册等)、以及
(h) 本产品表面包括液晶显示屏(LCD)表面的任何变形、变色和 / 翘曲。
为了获得本保证书规定的服务,原买方必须使用原包装或其他具有同等保护程度的适当包装将本产品运送到当地的经销商,
并且预付运费,承担运输中的损坏和 / 或损失的风险。要求提供本保证书规定的服务时,原买方必须提交购买本产品和标
明此购买日期的证明。
按本保证书规定进行了更换和 / 或修理的任何产品的保证期限,将在原保证期限结束时终止。
在返回给 EIZO 和经销商进行修理后,任何产品的任何媒体或任何部件中储存的数据或其他信息发生任何损坏或损失,对
此 EIZO 和经销商将不承担责任。
对于本产品及其质量、性能、可销售性以及对于特殊用途的适合性,EIZO 和经销商不提供其他任何明示或暗示的保证。因
使用本产品或无法使用本产品或因与本产品有任何关系(无论是否根据合同)而造成 : 任何附带的、间接的、特殊的、随
之发生的或其他的损害(包括但不仅限于:利润损失、业务中断、业务信息丢失或其他任何金钱损失)以及侵权行为、过失、
严格赔偿责任或其他责任,即使已经向 EIZO 和经销商提出了发生这些损害的可能性,对此 EIZO 和经销商概不承担责任。
本免责条款还包括因第三方向原买方提出索赔而可能发生的任何责任。 本条款的本质是限定由于本有限责任保证书和 / 或
销售本产品所发生的 EIZO 和经销商的潜在责任。
78
Appendix
Recycling Information
Recycling Information
This product, when disposed of, is supposed to be collected and recycled according to your country’s
legislationtoreduceenvironmentalburden.Whenyoudisposeofthisproduct,pleasecontactadistributoror
anaffiliateinyourcountry.
ThecontactaddresseesarelistedontheEIZOwebsitebelow.
http://www.eizo.com
ForrecyclinginformationforcustomersinSwitzerland,pleaserefertothefollowingwebsite.
http://www.swico.ch
Informationen zum Thema Recycling
Dieses Produkt muss gemäß den Vorschriften Ihres Landes zur Entlastung der Umwelt recyclet werden.
Wenden Sie sich beider Entsorgung dieses Produkts aneinen Verteileroder eineTochtergesellschaft in
IhremLand.
DieAdressenzurKontaktaufnahmesindaufderuntenangegebenenWebsitevonEIZOaufgeführt.
http://www.eizo.com
KundeninderSchweizentnehmenInformationenzumRecyclingderfolgendenWebsite:
http://www.swico.ch
Informations sur le recyclage
Ceproduitdoitêtrejetéauxpointsdecollecteprévusàceteffetetrecycléconformémentàlalégislationde
votrepays,afinderéduirel’impactsurl’environnement.Lorsquevousjetezceproduit,veuillezcontacterun
distributeurouunesociétéaffiliéedevotrepays.
LesadressesdesdistributeurssontrépertoriéessurlesiteWebEIZOci-dessous.
http://www.eizo.com
Pour les clients en Suisse, veuillez consulter le site Web suivant afin d’obtenir des informations sur le
recyclage.
http://www.swico.ch
Información sobre reciclaje
Este producto debe desecharse y reciclarse según la legislación del país para reducir el impacto
medioambiental.Cuandodeseedeshacersedeesteproducto,póngaseencontactoconundistribuidoro
unafilialdesupaís.
EncontrarálasdireccionesdecontactoenelsitiowebdeEIZOqueseindicaacontinuación.
http://www.eizo.com
Informazioni sul riciclaggio
Perlosmaltimentoeilriciclaggiodelpresenteprodotto,attenersiallenormativevigentinelpropriopaeseper
ridurrel’impattoambientale.Perlosmaltimento,rivolgersiadundistributoreounaffiliatopresentinelproprio
paese.
GliindirizzisonoelencatinelsitoWebEIZOriportatodiseguito.
http://www.eizo.com
PerinformazionisulriciclaggiopericlientiinSvizzera,consultareilsitoWebriportatodiseguito.
http://www.swico.ch
Återvinningsinformation
När denna produkt kasseras ska den hanteras och återvinnas enligt landets föreskrifter för att reducera
miljöpåverkan.Närdukasserarproduktenskadukontaktaendistributörellerrepresentantidittland.
KontaktadressernalistaspåEIZO-webbplatsennedan.
http://www.eizo.com
Appendix
79
Πληροφορίες ανακύκλωσης
Τοπροϊόναυτό,όταναπορρίπτεται,πρέπεινασυλλέγεταικαιναανακυκλώνεταισύμφωναμετηνομοθεσία
τηςχώραςσαςέτσιώστεναμηνεπιβαρύνειτοπεριβάλλον.Γιανααπορρίψετετοπροϊόν,επικοινωνήστεμε
έναναντιπρόσωποήμιαθυγατρικήεταιρείαστηχώρασας.
ΟιδιευθύνσειςεπικοινωνίαςαναγράφονταιστηντοποθεσίαwebτηςEIZOπαρακάτω.
http://www.eizo.com
Сведения по утилизации
По истечении срока службы данного продукта его следует принести на сборный пункт и
утилизировать в соответствии с действующими предписаниями в вашей стране, чтобы уменьшить
вредное воздействие на окружающую среду. Прежде чем выбросить данный продукт, обратитесь к
дистрибьюторуиливместноепредставительствокомпанииввашейстране.
Контактныеадресаможнонайтинавеб-узлеEIZO.
http://www.eizo.com
Informatie over recycling
Wanneeruditproductwiltweggooien,moethetuitmilieu-overwegingenwordenverzameldengerecycled
volgens de betreffende wetgeving van uw land. Wanneer u dit product wilt weggooien, moet u contact
opnemenmeteendistributeurofeenpartnerinuwland.
DecontactadressenwordenvermeldopdevolgendeEIZO-website.
http://www.eizo.com
Informação sobre reciclagem
Esteproduto,quandoodeitarfora,deveserrecolhidoerecicladodeacordocomalegislaçãodoseupaís
parareduzirapoluição.Quandodeitarforaesteproduto,contacteumdistribuidorouumafilialnoseupaís.
OsendereçosdecontactoestãolistadosnowebsitedoEIZO,abaixo.
http://www.eizo.com
Oplysninger om genbrug
Dette produkt forventes ved bortskaffelse at blive indsamlet og genbrugt i overensstemmelse med
lovgivningen i dit land for at reducere belastningen af miljøet. Når du bortskaffer denne produkt, skal du
kontakteendistributørellerettilknyttetselskabiditland.
AdressernepåkontaktpersonerneerangivetpåEIZO’swebstednedenfor.
http://www.eizo.com
Kierrätystä koskevia tietoja
Tuote tulee hävittää kierrättämällä maan lainsäädännön mukaisesti ympäristön kuormittumisen
vähentämiseksi.Kunhävitättuotteen,otayhteyttäjälleenmyyjääntaitytäryhtiöönmaassasi.
YhteystiedotlöytyvätEIZOnInternet-sivustolta.
http://www.eizo.com
Wykorzystanie surowców wtórnych
Tenproduktpozużyciupowinienbyćzbieranyiprzetwarzanyzgodniezkrajowymiprzepisamidotyczącymi
ochrony środowiska. Wyrzucając ten produkt, należy skontaktować się z lokalnym dystrybutorem lub
partnerem.AdresykontaktowemożnaznaleźćwewskazanejponiżejwitrynieinternetowejfirmyEIZO.
http://www.eizo.com
80
Appendix
Informace o recyklaci
Při likvidaci produktu musí být produkt vyzvednut a recyklován podle zákonů příslušné země, aby
nedocházelo k zatěžování životního prostředí. Zbavujete-li se produktu, kontaktujte distributora nebo
pobočkuvesvézemi.KontaktníadresyjsouuvedenynanásledujícíwebovéstráncespolečnostiEIZO.
http://www.eizo.com
Ringlussevõtu alane teave
Keskkonnakoormusevähendamisekstulekskasutatudtootedkokkukogudajavõttaringlussevastavaltteie
riigiseadustele.Kuikõrvaldatekäesolevatoote,võtkepalunühendustturustajavõifiliaaligaomariigis.
KontaktisikudontoodudEIZOveebileheljärgmiselaadressil:
http://www.eizo.com
Újrahasznosítási információ
Jelenterméket,amikoreldobjuk,azilletőországtörvényeialapjánkellösszegyűjteniésújrahasznosítani,
hogy csökkentsük a környezet terhelését.Amikor ezt a terméket eldobja, kérjük lépjen kapcsolatba egy
országonbelüliforgalmazóvalvagytársvállalkozással.
AkapcsolatcímeiazEIZOalábbiweboldalántalálhatókfelsorolva:
http://www.eizo.com
Podatki o recikliranju
Ob koncu uporabe odslužen izdelek izročite na zbirno mesto za recikliranje v skladu z okoljevarstveno
zakonodajo vaše države. Prosimo, da se pri odstranjevanju izdelka obrnete na lokalnega distributerja ali
podružnico.
KontaktninaslovisoobjavljeninaspodajnavedenihspletnihstranehEIZO:
http://www.eizo.com
Informácie o recyklácii
Prilikvidáciimusíbyťtentovýrobokrecyklovanývsúladeslegislatívouvašejkrajiny,abysaznížilozaťaženie
životnéhoprostredia.Keďsachcetezbaviťtohtovýrobku,kontaktujteprosímdistribútoraalebopobočkuvo
vašejkrajine.
ZoznamkontaktnýchadriesjeuvedenýnanasledovnejwebovejstránkefirmyEIZO:
http://www.eizo.com
Pārstrādes informācija
Utilizējot šo produktu, tā savākšana un pārstrāde veicama atbilstoši jūsu valsts likumdošanas prasībām
attiecībā uz slodzes uz vidi samazināšanu. Lai veiktu šī produkta utilizāciju, sazinieties ar izplatītāju vai
pārstāvniecībujūsuvalstī.
KontaktadresesirnorādītaszemākminētajāEIZOtīmekļavietnē.
http://www.eizo.com
Informacija apie grąžinamąjį perdirbimą
Šalinant(išmetant)šiuosgaminiusjuosreikiasurinktiirperdirbtigrąžinamuojubūdupagaljūsųšaliesteisės
aktus, siekiant sumažinti aplinkos teršimą. Kai reikia išmesti šį gaminį, kreipkitės į jūsų šalyje veikiančią
gaminiųpardavimoatstovybęarbajosfilialą.
KontaktiniaiadresatainurodytiEIZOinternetosvetainėje.
http://www.eizo.com
Appendix
81
Информация относно рециклиране
Приизхвърлянетонатозипродуктсепредлагасъбиранетоирециклиранетомусъобразнозаконитена
вашатастраназадасенамализамърсяванетонаоколнатасреда.Когатоискатедасеосвободитеот
тозипродукт,молясвържетесестърговскиямупредставителилисъссъответнитеорганиотговарящи
затовавъввашатастрана.
ДаннитезавръзкаснассаописанинаследнияИнтернетсайтнаEIZO:
http://www.eizo.com
Informaţie referitoare la reciclare
Acestprodus,cânddebarasat,trebuiecolectatşireciclatconformlegislaţieiţăriirspectivecasăreducem
sarcinamediului.Cândsedebaraseazădeacestprodus,vărugămsăcontactaţiundistribuitorsauunafiliat
alţăriirespective.
AdreseledecontactlegăsiţipepaginadewebalEIZO:
http://www.eizo.com
Geri Dönüşüm Bilgisi
Buürünün,atılacağızaman,ülkenizinçevrekirliliğininazaltılmasıkonusundakimevzuatınagöretoplanması
veyenidendeğerlendirilmesigerekmektedir.Ürünüatacağınızzamanlütfenülkenizdekibirdistribütörveya
ilgilikuruluşlatemasageçiniz.
İrtibatadresleriaşağıdakiEIZOwebsitesindeverilmiştir.
http://www.eizo.com
82
Appendix
China Measures for RoHS Compliance in ChinaRoHS
关于电子信息产品污染控制标识
本标识根据「电子信息产品污染控制管理办法」,适用于在中华人民共和国销售的电子信息产品。标识中央的
数字为环保使用期限的年数。只要您遵守该产品相关的安全及使用注意事项,在自制造日起算的年限内,不会
产生对环境污染或人体及财产的影响。上述标识粘贴在机器背面。
• 有毒有害物质或元素的名称及含量
部件名称
有毒有害物质或元素
铅
汞
镉
六价铬
多溴联苯
多溴二苯醚
(Pb)
(Hg)
(Cd)
(Cr(VI))
(PBB)
(PBDE)
印刷电路板
×
○
○
○
○
○
机箱
○
○
○
○
○
○
液晶显示器
×
○
○
○
○
○
其他
×
○
○
○
○
○
○ :表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 规定的限量要求以下。
× :表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 规定的限量要求。
( 企业可在此处 , 根据实际情況对上表中打“×” 的技术原因进行进一步说明 )
Appendix
83
2nd Edition-August, 2013
Copyright © 2012-2013 EIZO Corporation All rights reserved.
03V24733B1
(U.M-EV2416W-Z)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising