2010 - Product Guide
Contents
Innovation AV Switchers
Revolution DSP
AMIS Series Mixers Amps
AMC Series Mixer Amps
Mixers
Performance Mixing Console
Amplifiers
Zone Paging CD Players and Tuners
Equalizers
Crossover
Compressor-Limiter
Contractor Tools
Headphone amp
Phantom Power Supply
Mic Spliiter
Line Splitter
Pro to consumer level matching
Direct box
Pages 3-4
Pages 5-7
Pages 8-11
Pages 12-13
Pages 14-17
Pages 18-19
Pages 20-23
Pages 24-26
Page 27
Page 28
Page 29
Page 29
Pages 30-31
Mic Pre-amp
Hum eliminator
Speaker-to-line level matching
Distribution amp
Monitor panel
Digital Message Announcer
Speakers
AV Essentials - microphones
Page 32-33
Page 34
5 year warranty with every Australian Monitor purchase.
http://amav.starin.biz
INNOVATION SERIES
IN 600 - Audio & Video Switcher with integral audio amplifier
The IN600 takes the Innovation Series concept to a higher level of flexibility with complete system control. Featuring
an onboard mic/line mixer, six AV source inputs with six balanced XLR outputs, the IN600 can also be configured
as a 5.1 front end. Including RS232 projector control and logic output for screen up/down control, the IN600 gives
the AV integrator full room AV control or optional Crestron or third party interfacing. Dedicated Innovation software
allows for set up of all function parameters, and the IN600 will also be compatible with a soon to be released series
of wall panels. The IN600 - untold AV control flexibility in a user friendly and cost-effective package.
•
•
•
•
•
•
•
•
•
•
•
•
•
4 XLR mic/line and RCA inputs
2 x DVD inputs featuring VGA (component),
composite video and 5.1 RCA audio
2 x AUX inputs featuring composite video
and stereo RCA audio
2 x PC inputs featuring VGA video and
stereo RCA audio
1x composite video and 1x VGA video output
6 balanced XLR outputs (5.1 out)
7x “Select” buttons on front panel for 6
sources and “Off” (LED indication of selected
source) - RS485 and front panel control
Sub output features 24dB/Oct LPF at 120Hz
VGA/Composite video select switch on rear
panel for DVD1 and DVD2
Projector RS232 control to allow for
switching between composite and VGA
sources
Screen up and screen down external logic
control
Front panel control
RS485 control
Specs:
Line Audio:
THD <0.5%
Noise Floor -90dBu
Frequency Response (+/-3dB) 20Hz-20kHz
Gain (trim centre)
XLR Mic 45dB
XLR Line 0dB
RCA line 12dB
RCA switched 0dB
Headroom 15dBu
Video:
VGA High speed RGB+Sync switching
Video Composite 75Ohm Buffered outputs
Video follows audio switching
Comms:
Type R
S485
Baud Rate 9600
Number of Data Bits 8
Parity None
Number of Stop Bits 1
Power Consumption (max): 30VA
Dimensions: 3.5”H x 19”W x 9.82”D
Net Weight: 9.4lb
Shipping Dimensions: 7.5”H x 20.5”W x 14.2”D
Shipping Weight: 14.3lb
page 3
IN 400 - Audio & Video Switcher with integral audio amplifier
The IN400 is a compact AV switching amplifier with a host of extra features available to the AV integrator. The IN400
is a one box solution for any application with a mix of audio and video sources. With 8 AV inputs as well as mix in,
stereo line output, 2 composite video outputs, VGA video output, 80 watt per channel powered outputs, IR control,
RS485 control and video away from audio split, the IN400 is perfect for boardroom, lecture theatre or training facility
installations as a stand alone control unit or as part of a larger system interfacing with a third party control system.
•
•
•
•
•
•
•
•
•
•
•
•
•
4 composite video/stereo audio inputs
2 Composite video outputs
4 VGA (SXGA resolution)/stereo audio
inputs
VGA video output
Mix stereo RCA audio input
Emergency override input
Stereo audio line level output
IR remote control (source select,
volume and bass/treble control)
RS485 port for third party control
(e.g. Crestron)
Front panel source select and volume
control c/w LED indication
Bass and Treble control via IR and
RS485 control
1RU
On board 2 x 80 watt amplifier
http://amav.starin.biz
Specs:
Power Output (0.5%THD, 1kHz):
2x50W @ 8 Ohms, 2x80W @ 4 Ohms
THD (20-10kHz, 8ohm, -2dBr): Better than 0.1%
Frequency Response (+/-3dB): 20Hz-20kHz
Gain: 24dB @ 8Ohm
Line Audio:
THD <0.5%
Noise Floor -90dBu
Frequency Response (+/-3dB) 20Hz-20kHz
Headroom +5dBu
Video:
VGA High speed RGB+Sync switching
Video Composite 75ohm Buffered outputs
Video follows audio switching
Comms:
Type R
S485
Baud Rate 9600
Number of Data Bits 8
Parity None
Number of Stop Bits 1
Power Consumption: 1/8 power 150VA (0.65A)
Thermal Output: 1/8 power 100W (341.2Btu/hr)
Dimensions: 1.75”H x 19”W x 12.8”D
Net Weight: 15.4lb
Shipping Dimensions: 3.5”H x 19”W x 16.5”D
Shipping Weight: 19.8lb
REVOLUTION SERIES
AV Revolution - Digital Signal Processor for presentation spaces
The AV Revolution is packed with processing power for applications ranging from lecture theatres and boardrooms
through to function room systems with room-combining. With accessories such as CobraNet cards and remote wall
panels, the AV revolution offers a combination of stereo and mono outputs as well as stereo and mono mic line
inputs. Whether used for straight signal processing or source routing applications, the AV Revolution can do it all.
•
•
•
•
•
•
•
•
•
•
•
•
3 stereo output zones
2 mono output zones
6 stereo line sources available to all five
output zones
4 mic/line switchable inputs available to
all five output zones
Support for a range of remote control
panels (RS-485 protocol)
Ethernet control of audio parameters via
Crestron or other third party interfacing
“Master override” input (mic/line input
4) with logic triggering to override zone
mixes
Ability for stereo zone outputs to be mono
summed, allowing up to two uniquely
processed outputs per zone
Various EQ, dynamics and delay
processing on inputs and outputs
Simple setup using configuration software
Integrated user GUI
Front panel input/output signal present
indication
page 5
Specs:
Balanced Mic Input:
Impedance 2k Ohms
Phantom Power 48 V
Gain/Max Input 6 dB/6dBu, 24 dB/-12dBu,
42 dB/-12dBu, 60dB/-48dBu
Balanced Line Input:
Impedance 5KOhm
Gain/Max Input -12dB/24dBu, +6dB/6dBu
Unbalanced RCA Input:
Impedance 15k Ohms
Maximum Input 6.2 dBu
Balanced Outputs:
Impedance 50 Ohms
Maximum Output 24 dBu
System:
Frequency Response 20-20,000Hz
THD + N 0.003%
Dynamic Range 108 dB
Sample Rate 48kHz
Latency 2.1ms
Processor 2 x Analog Devices Sharc DSP
(ADSP-21375) 32/40 bit floating point
Processing Power 2 x 1596 MFLOPS
Communications:
Ethernet 100 Base T
Icon Control Panel RS485 500m
Voltage 90-264 VAC
Power Consumption <30 VA
Zone Revolution -Digital Signal Processor for paging
The Zone Revolution offers a multi-zone solution to the bar/club market. Combining state-of-the-art processing speed
with multiple stereo and mono inputs and outputs, the Zone Revolution is designed to handle the most challenging
foreground/background audio scenarios. Two Zone Revolutions can be linked to provide even more zone flexibility.
The ICON paging stations and Revolution Series wall panel remotes cater for a host of interface functions including
clever paging facilities, source or zone selection, system preset recalls, volume control and many other system features.
•
•
•
•
•
•
•
•
•
•
•
•
•
3 stereo output zones
Additional sub/aux outputs on the first two stereo zones
4 stereo BGM source inputs available to all three output zones
Ability for Stereo input 4 to have priority over all BGM source
inputs (‘jukebox’ functionality)
4 mic/line switchable inputs available to all three output zones
Support for up to two remote paging stations with the ability to
page simultaneously
Support for a range of remote control panels (RS-485 protocol)
Ethernet control of audio parameters for Crestron or other third
party interfaces
Ability to link two Zone Revolutions to achieve six stereo output
zones
“Master override” input (mic/line input 4) with logic triggering to
override zone mixes
Various levels of source priority and ducking
Ability for stereo zone/aux/sub outputs to be mono summed,
allowing up to three uniquely processed outputs per zone
Various EQ, dynamics and delay processing on inputs and outputs
http://amav.starin.biz
Paging Station & Wall Panel
The Revolution Series represents a giant leap forward in the ease of
configuration and installation of DSP products. With a range of visually
impressive and ergonomically friendly wall panels and
paging stations, the simplicity of use is carried through to the end user where
the intuitive interfaces will be most appreciated.
The ICON paging station is easy to operate for even the most inexperienced
user, and reinvents the dated look of paging stations
with a striking new design. Expansion modules and CobraNet variants for
the ICON paging station will also become available in the future, further
extending the flexibility of the Revolution Series in
any commercial installation.
The intuitive, simple-to-use design concept of the
Revolution Series is carried through to the wall
mount control interface. These stylish panels can
be configured to perform volume control, source
selection, muting, or preset recall whilst giving the
user feedback of system status on the visual display.
Aesthetically pleasing, simple in both programming
and use, the cost effective Revolution Series makes
complex commercial DSP installations a thing of
the past.
Software Interface
The Revolution software design has achieved
the rare feat of combining ease-of-use for the
contractor, while still allowing the high level of
functionality many installations require. Both
Revolution Series DSP models feature software
interfaces with a similar look and feel.
The clearly laid out graphics can also be
password protected, allowing the PC based GUI
to be operated by the client, or addressed via
Crestron or other third party control system.
page 7
amis series
The Australian Monitor Installation Series (AMIS) is a world-class range of background music and paging
systems. Offering well featured mixer amplifiers, power amplifiers, zone solutions and various speaker
and contractor tool products, the range has grown in recent years to become a substantial and formidable
catalogue. Clever Features, Contractor Friendly is our motto and the design philosophy behind this very
successful brand.
AMIS 60 - 4 Input 60 Watt Mixer-Amplifier
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
4 balanced dual mic/line inputs
Overall bass and treble controls
70V and 8 ohm outputs
Vox muting from channels 1 and 2 (defeatable)
Bell, Pre Announce, Evac and Alert tones in-built
(rear panel activation)
Vox triggered relay output
VCA remote master level control RC1
Temperature Sensing Fan Cooling
Insert point for connection of AMIS EQ or other
processors
15V Phantom power on all mic inputs (defeatable
by rear switch)
6 zone speaker selector with ‘all call’
Both overall and internal limiting
Balanced XLR 700mV output for connection to
multiple power amps
Tape Output 350mV @ 10K ohms
Signal Present LED
2RU
120VAC/24VDC operation
http://amav.starin.biz
AMIS 60 SPECIFICATIONS
Power Output: 60 Watts RMS
Maximum Load: 80 Ohms @ 70 Volts
Power Bandwidth:
60Hz - 17kHz (- 3dB)
Frequency Response:
60Hz - 23kHz (- 3dB)
Total Harmonic Distortion:
0.5% @ 1kHz rated power
Signal To Noise Ratio:
-74dB all controls center
Tone Controls: Bass @ 100Hz, Boost
+12dB Cut -12dB, Treble @ 10kHz, Boost
+9dB Cut -9dB
Input Sensitivity:
Mics: 1mV @ 200 Ohms Aux: 150mV @ 47K Ohms
Outputs: Speaker: 70 Volts, 8 Ohm Tape: 350mV @10KOhms Line: Balanced 700mV
Phantom Power:
18 V DC Mic ins- Switch
Controls: 4 input channel gain
1 Bass control
1 Treble control
1 Master gain control
6 Speaker zone selector
1 Speaker “all call” selector
1 Pre-announce defeat switch
1 Phantom Power switch Tone Generators: Four tone generator with Bell,
Pre-Announce, Alert and Evac
Protection: Soft limiter for overload protection, plus AC and DC fuses.
Muting:
Channels 1 and 2 will mute
channels 3 and 4
Indicators: Power “on” LED
Power Source:120VAC 60Hz,
3 pin IEC connector; 24VDC
Power Consumption: 125 Watts
Dimensions: 3.5” H x 19” W x 13”D Weight: 22 lbs.
AMIS 120 - 4 Input 120 Watt Mixer-Amplifier
•
•
•
4 balanced mic/dual RCA line inputs
70 volt 4 or 8 ohm operation
Vox muting on channels 1 and 2
Bell, Pre Announce, Evac and Alert
tones on board
•
•
•
•
•
Vox triggered output relay
VCA master level control
15 VDC phantom power
2 RU
Mains or 24DVC operation
Inputs
The AMIS has four universal input channels with separate level controls. Each
channel will accept balanced or unbalanced microphone, line and auxiliary
inputs. The unit has industry standard XLR microphone sockets and dual RCA
auxiliary sockets for each channel. An insert point is also featured on the rear
panel for those applications where an additional EQ or feedback eliminator may
be required.
Outputs
The AMIS 60 features 70 volt and 8 ohm while the AMIS 120 features 70 volt, 4
& 8 ohm isolated transformer outputs, plus a tape recorder output by means of
dual RCA sockets. A balanced 700mV XLR output is also provided to feed up to
6 power amplifiers. A vox triggered relay output is also available on the rear panel
for activation of external devices from the vox muting circuit. In most cases this
would be used as a muting bypass relay, which when used with the appropriate
external attenuator will maintain paging levels irrespective of the attenuator
setting.
VCA Control RC1
The master volume can be controlled remotely. External VCA control would
normally be via a pot connected to a two wire rear panel barrier strip.
Speaker Zone Selector
A six position push button speaker zone selector with overriding “all call” is
located on the front panel. Each of the six zone selectors switch the 70 volt
speaker line output to 6 separate speaker zones. The “all call” selector overrides
all 6 zones regardless of their on/off condition and places the 70 volt output to all
6 zones.
Tone Generator
The AMIS series comes standard with an in-built four tone generator module.
Tones include Bell, Pre-announce Chime, Alert Tone and Evacuate Tone. Any of
these tones may be activated from a simple contact closure connected to the rear
panel of the amplifier. A Pre-announce defeat switch is located on the front panel.
Muting
VOX muting is standard on the AMIS series. A mic or line signal on channels 1 or
2 will mute channels 3 and 4. The muting function can be disabled via an internal
link.
page 9
AMIS 120 SPECIFICATIONS
Power Output: 120 Watts RMS
Maximum Load: 40 Ohms @ 70 Volts
Power Bandwidth: 60Hz - 17kHz (- 3dB)
Frequency Response: 60Hz - 23kHz (- 3dB)
Total Harmonic Distortion:
0.5% @ 1kHz rated power
Signal To Noise Ratio:
-74dB all controls center
Tone Controls: Bass @ 100Hz
Boost +12dB Cut -12dB Treble @ 10kHz Boost +9dB Cut -9dB
Input Sensitivity: Mics: 1mV @ 200 Ohms Aux: 150mV @ 47K Ohms
Outputs: Speaker: 70 Volts, 4 & 8 Ohm Tape: 350mV @10KOhms Line: Balanced 700mV
Phantom Power: 18 V DC Mic ins- Switch
Controls: 4 input channel gain 1 Bass control
1 Treble control 1 Master gain control 6 Speaker zone selector 1 Speaker “all call” selector 1 Pre-announce defeat switch 1 Phantom Power switch Tone Generators: Four tone generator with Bell, Pre-Announce, Alert and Evac
Protection: Soft limiter for overload protection, plus AC and DC fuses.
Muting: Channels 1 and 2 will mute
channels 3 and 4
Indicators: Power “on” LED
Power Source: 120VAC 60Hz 3 pin IEC connector; 24VDC
Power Consumption: 250 Watts
Dimensions: 3.5” H x 19” W x 13” D Weight: 26.5 lbs.
AMIS 120XL - 8 Input 120 Watt Mixer-Amplifier
Description
The AMIS120XL is an 8 channel, 120 watt mixer amplifier suitable for rack or
desk mounting. The amplifier is a self contained compact unit of solid steel
construction. This amplifier features a status LED.
Inputs
The AMIS120XL has eight universal input channels with separate level controls.
Each channel will accept balanced or unbalanced microphone, line and auxiliary
inputs. The unit has industry standard XLR microphone sockets and dual RCA
auxiliary sockets for each channel. Rear panel dip switches per channel allow
the adjustment of line input sensitivity. An insert point is also featured on the rear
panel for those applications where an additional EQ or Feedback Exterminator
may be required.
Outputs
The AMIS120XL features 70 volt, 4 & 8 ohm isolated transformer outputs, plus
a tape recorder output by means of dual RCA sockets. A balanced 700mV XLR
output is also provided to feed up to 6 power amplifiers. A vox triggered relay
output is also available on the rear panel for activation of external devices from
the vox muting circuit. In most cases this would be used as a muting bypass
relay, which when used with the appropriate external attenuator will maintain
paging levels irrespective of the attenuator setting.
VCA Control RC1
The master volume level can be controlled remotely. External VCA control would
normally be via a pot connected to a two wire rear panel barrier strip.
Tone Generator
The AMIS120XL comes standard with an in-built four tone generator module.
Tones include Bell, Pre-announce Chime, Alert Tone and Evacuate Tone. Any
of these tones may be activated from a simple contact closure connected to the
rear panel of the amplifier.
Muting
Multiple levels of VOX muting is standard on the AMIS120XL. A mic or line signal
on channels 1 will mute channels 2 to 8, on channel 2 will mute 3-8 and channel
3, will mute 4-8. The muting function can be disabled via an internal link. A vox
triggered relay output is also available on the rear panel for activation of external
devices from the vox muting circuit. In most cases this would be used as a
muting bypass relay, which when used with the appropriate external attenuator
will maintain paging levels irrespective of the attenuator setting.
http://amav.starin.biz
AMIS 129XL SPECIFICATIONS
Power Output: 120 watts RMS
Maximum Load: 40 Ohms @ 70 Volts
Power Bandwidth:
60Hz - 17kHz (- 3dB)
Frequency Response: 60Hz - 23kHz (- 3dB)
Total Harmonic Distortion: 0.5% @ 1KHz rated power
Signal To Noise Ratio:
-74dB with all controls at center
Tone Controls: Bass @ 100Hz
Boost +12dB Cut -12dB Mid @ 600Hz Boost +12dB Cut -12dB Treble @ 10kHz Boost +9dB Cut -9dB
Inputs: Eight mic/aux universal inputs with XLR female and dual RCA plugs; 600 ohm transformer balanced
telephone paging input
Input Sensitivity:
Mics: 1mV @ 200 Ohms Aux: 150mV @ 47K Ohms with 9, 12, 15dB Pads
Outputs: Speaker: 70 Volts, 4 & 8 Ohms & 25V Tape: 350mV @ 10K Ohms Line: Balanced 700mV
Controls:
8 Input channel gain controls 1 Master gain control VCA rear panel strip
Dip Switch per Channel for line
sensitivity and phantom power and a
vox relay out
Phantom Power: 18V DC on all Mic ins- Switch Tone Generators: Four tone generator with Bell, Pre-Announce, Alert and Evac
Muting: Channel 1 will mute chans.
2 to 8, channel 2 mutes 3 - 8,
channel 3 mutes 4 - 8.
Also a vox relay to external devices.
Indicators: Power “on” & signal present LEDs
Dimensions:
3.5” H x 19” W x 13” D
Weight: 26.5lb
AMIS 250 - 6 Chan 250 Watt Mixer-Amplifier
Description
The AMIS250 is a 6 channel, 250 watt mixer amplifier suitable for rack or desk
mounting. The amplifier is a self contained compact unit of solid steel construction.
Inputs
The AMIS250 has six universal input channels with separate level controls. Each
channel will accept balanced or unbalanced microphone, line and auxiliary inputs.
The unit has industry standard XLR microphone sockets and dual RCA auxiliary
sockets for each channel. An insert point is also featured on the rear panel for
those applications where an additional EQ or feedback exterminator may be
required.
Outputs
The AMIS250 features 70 volt & 25V and 4 ohm isolated transformer outputs, plus
a tape recorder output by means of dual RCA sockets. A balanced 700mV XLR
output is also provided to feed up to 6 power amplifiers.
VCA Control RC1
The master volume level can be controlled remotely. External VCA control would
normally be via a pot connected to a two wire rear panel barrier strip.
Tone Generator
The AMIS250 comes standard with an in-built four tone generator module. Tones
include Bell, Pre-announce Chime, Alert Tone and Evacuate Tone. Any of these
tones may be activated from a simple contact closure on the rear panel of the
amplifier.
Muting
VOX muting is standard on the AMIS250. A mic or line signal on channels 1 or
2 will mute channels 3, 4, 5 and 6. The muting function can be disabled via an
internal link.
Phantom Power
Phantom Power (18V DC) is available from all mic inputs. A rear panel phantom
power on/off switch is also provided.
Protection
Internal current limiting protects the amplifier from both overload and overdrive
conditions. Australian Monitor Installation Series amplifiers feature a protection
network that provides greater stability and performance. Our amplifiers are
recognised worldwide for their reliability and this is due to the extensive levels
of current limiting which protect the amplifiers from both overload and overdrive
conditions.
page 11
AMIS 250 SPECIFICATIONS
Power Output: 250 watts RMS
Maximum Load: 20 Ohms @ 70 Volts
Power Bandwidth: 60Hz - 17kHz (- 3dB)
Frequency Response: 60Hz - 23kHz (- 3dB)
Total Harmonic Distortion: 0.5% @ 1kHz rated power
Signal To Noise Ratio:
-74dB with all controls at center
Tone Controls: Bass @ 100Hz: Boost +12dB Cut -12dB
Mid @ 600Hz: Boost +12dB, Cut -12dB Treble @ 10kHz: Boost +9dB Cut -9dB
Inputs: Six mic/aux universal inputs with XLR female mic sockets and dual RCA Phono aux sockets; 600 ohm transformer balanced telephone paging input
Input Sensitivity: Mics: 1mV @ 200 Ohms Aux: 150mV @ 47K Ohms Outputs Speaker: 70 V, 4 Ohms Tape: 350mV @ 10K Ohms
Line: Balanced 700mV
Phantom Power: 18 Volts DC on all Mic inputs
Controls:
6 Input channel gain controls 1 Master gain control 1 Phantom Power on/off switch
Tone Generators Four tone generator with Bell, Pre-Announce, Alert and Evac
Muting: Built-in VOX muting. Channels 1 and 2 will mute channels 3, 4, 5 and 6
Indicators: Power “on” and “Protect” LED
Power Source: 120VAC 60Hz 3 pin IEC; 24VDC
Power Consumption: 400 Watts
Dimensions: 3.5” H x 19” W x 13” D
Weight 33.1lb
AMC SERIES
The Australian Monitor Installation Series AMC line of amplifiers takes the heritage & reliability of our famous AMIS
series & integrates these features into a low cost amplifier format for applications where reliability is everything,
but the more elaborate features of our AMIS series are not required. The 30 watt version of the AMC series is a
2 RU mixer amplifier featuring 70 volt line & 4 ohm outputs & 3 universal mic/line inputs.
Master volume & overall treble/bass controls are provided, along with Voice triggered muting (defeatable) giving
channel 1 priority over inputs 2 & 3. There is also facility to internally add a tone generator card.
The Australian Monitor AMC series give the contractor a low cost alternative in applications that are cost sensitive,
but still require a high quality of sound reproduction & reliability.
AMC 30 - 30 Watt 2RU Mixer-Amplifier
•
•
•
•
•
•
•
•
•
3 balanced XLR mic/dual RCA line inputs
30 watt output power
2 Rack units in height
70 volt or 4 ohm operation
Master treble and bass control
Channel 1 has priority over channels 2 & 3
(defeatable)
Facility to add a tone generator module ATC5488
Tape output (pre master)
Balanced line output
AMC 30 SPECIFICATIONS
Power output: 30W
Outputs: 4 Ohms, 70V
THD before clipping: 0.5%
Inputs: 3x (Mic/Aux)
Input connectors: 3x (XLR/RCA)
Mic sensitivity: 1mV+/-0.2mV
AUX sensitivity: 0.5V+/-100mV
S/N ratio: > 75dBr
Bandwidth On 70V terminals:
85Hz-15kHz (-3dB +0dB)
Tone Controls Bass @ 100Hz: +/- 12 dB
Treble @ 10kHz: +/- 9 dB
Power source: 115V 60 Hz
Current draw (full power): .73 A
Fuses: 1A - AC mains & DC
Line Out: 1V
Tape Out: 300mV
Mic 1 Automatic: Priority over Mic 2/3
Size: 19” W x 3.5” H x 7.5” D
Protections:
1) Short circuit 2) No Thermal
Output Regulation: 96%
Net Weight: 13.2lb
Shipping Dimensions:
20.1” W x 5.7” H x 11.7” D
Shipping Weight: 16.5lb
http://amav.starin.biz
AMC 60 - 60 Watt 2RU Mixer-Amplifier
• 3 balanced XLR mic/dual RCA line inputs
• 60 watt output power
• 2 Rack units in height
• 70 volt or 4 ohm operation
• Master treble and bass control
• Channel 1 has priority over channels 2 & 3 (defeatable)
• Facility to add a tone generator module ATC5488
• Tape output (pre master)
• Balanced line output
AMC 60 SPECIFICATIONS
Power output: 60W
Outputs: 4 Ohms, 70V
THD before clipping: 0.5%
Inputs: 3x (Mic/Aux)
Input connectors: 3x (XLR/RCA)
Mic sensitivity: 1mV+/-0.2mV
AUX sensitivity:0.5V+/-100mV
S/N ratio: > 75dBr
Bandwidth On 70V terminals:
75Hz-15kHz (-3dB +0dB)
Tone Controls Bass @ 100Hz: +/- 12 dB
Treble @ 10kHz: +/- 9 dB
Power source: 115V 60 Hz
Current draw (full power): 1.38 A
Fuses: 1A - AC mains & DC
Line Out: 1V
Tape Out: 300mV
Mic 1 Automatic: Priority over Mic2/3
Size: 19” W x 3.5” H x 11.1” D
Protections:
1) Short circuit 2) Thermal at 95%
Output Regulation: 96%
Net Weight: 18.7lb
Shipping Dimensions: 20.1” W x 5.7” H x 11.7”D
Shipping Weight: 23.1 lb
AMC 120 - 120 Watt
AMC 120 SPECIFICATIONS
Power output: 120W
Outputs: 4 Ohms, 70V
THD before clipping: 0.5%
Inputs: 3x (Mic/Aux)
Input connectors:3x (XLR/RCA)
Mic sensitivity: 1mV+/-0.2mV
AUX sensitivity: 0.5V+/-100mV
S/N ratio: > 80dBr
Bandwidth On 70V terminals
75Hz-15kHz (-3dB +0dB)
Tone Controls Bass @ 100Hz: +/- 12 dB
Treble @ 10kHz: +/- 9 dB
Power source: 115V 60 Hz
Current draw (full power): 2.5 A
Fuses: 1A - AC mains & DC
Line Out: 1V
Tape Out: 300mV
Mic 1 Automatic: Priority over Mic2/3
Size: 19” W x 3.5” H x 11.1” D
Protections:
1) Short circuit 2) Thermal at 95%
Output Regulation: 96%
Net Weight: 23.1lb
Shipping Dimensions: 20.1” W x 5.7” H x 11.7” D
Shipping Weight: 27.6 lb
2RU Mixer-Amplifier
• 3 balanced XLR mic/dual RCA line inputs
• 120 watt output power
• 2 Rack units in height
• 70 volt or 4 ohm operation
• Master treble and bass control
• Channel 1 has priority over channels 2 & 3 (defeatable)
• Facility to add a tone generator module ATC5488
• Tape output (pre master)
• Balanced line output
page 13
MIXERS
AMC MIX - 3 Channel Mixer
The Australian Monitor Installation Series AMC-MIX mixer brings the affordability
& ease of use of the AMC series amplifiers and offers accommodations a low cost
mixer for applications where reliability is everything but the more elaborate features
of the MX mixers series are not required.
The AMC-MIX is a 1 RU mixer that features 3 universal mic/line inputs. Master
volume & overall treble & bass controls are provided, along with vox triggered muting
(defeatable) giving channel 1 priority over channels 2 & 3. There is also facility to
add an optional on board tone generator card. The AMC-MIX gives the contractor a
low cost alternative in applications that are price sensitive but still require reliability
& a high level of sound reproduction.
•
•
•
•
•
3 Mic/line input mono mixer
Master Volume, overall treble & bass controls
1 RU
Optional tone generator ATC5483
On board priority
AMC MIX SPECIFICATIONS
Frequency Response: 20Hz - 20kHz (+0,-3dB)
Distortion: < 0.5% @ 1kHz (THD)
Signal to noise ratio: > 84dB (pots at center)
Crosstalk: > 60dB
Tone controls:
BASS @100HZ +/- 12dB
TREBLE @10KHZ +/9dB
Sensitivity:
Mic Sens 0.7mV, -61dBu Imp 1k3ohm
RCA 500mV, -4dBu Imp >100kohm
Max level in:XLR mic -20dBu
RCA >30dBu
Max level out:+14dBu
Master Out:
Nominal Level 0dBu into 1k Ohm Imp 100 Ohm
Mono tape out:
Nom -16dB into 10k Ohm
Imp 10k Ohm
Power Input: 20V AC via 2.1mmx5.5mm barrel
Power Consumption: 7 VA (max)
Dimensions HxWxD:
1.75”x19”x7.54”
WEIGHT: Net 5.5lb
Shipping 7.7lb
MX 61 SPECIFICATIONS
Frequency Response:
- 6 Channel Mixer
20Hz - 20kHz (+0,-3dB)
Distortion: < 0.1% @ 1kHz
Signal to noise ratio:
The MX61 mixer features the new Australian Monitor Standard (AMS) input section
> 90dB (all pots at center)
which has an XLR input switchable between mic & line level, dual RCA line inputs,
Crosstalk:>70dB
signal present LED indication, individually switchable phantom power, & +/- 15dB
Tone controls: BASS:@ 100HZ +/of gain trim available per input. The MX61 also boasts whisper quiet operation, 4
12dB, MID @ 1.6KHZ +/- 12dB,
segment output level indication & balanced line output, record output & headphone
TREBLE @ 10KHZ +/- 12dB
Sensitivity: Mic Sens 4.36mV, -45dBu outputs. The MX61 has 6 AMS inputs to one output & will operate via 110 VAC or
Imp 1k3ohm (Trim center- 0dB)
24VDC via an external 24 volt power supply. Optional remote VCA volume control,
Line Sens 0.775V, 0dBu, Imp >100k,
tone generators & muting boards are also available for the MX61 (see options on next
RCA 200mV, -12dBu, Imp 30kohm
page). The MX61 mixer is extremely versatile & represents excellent value for money.
Max level in: X
LR mic -15dBu line
+30dBu RCA >30dBu
Max level out:+21dBu
Phantom Power:15V DC
Master Out:Nominal Level 0dBu into
1kohm Imp 100ohm
Mono headphone out:
Nom -6dB into 200ohm Imp 10ohm
Mono Rec out:
Nom -12dB into 10kohm, Imp 10kohm
• 6 input mono mixer
• 24VDC or mains power operation
Power Input:AC: 115V/60Hz, 3 pin IEC,
• XLR input switchable between mic
• Optional remote VCA/Tone
DC: 24 Volts
&
line
level
generator/ Muting boards
Power Consumption (MAX): 7VA
• 15dB +/- gain trim control per input • Whisper quiet operation
Fuses: MAINS (115V) 120mA
Dimensions H x W x D: 1.75“x19”x7.2”
• Input 1 is switchable to be pre/post • Dual color signal present indication
Weight: Net 6.1lb, Shipping 8.3lb
master
LED per input
MX 61
http://amav.starin.biz
MX 81 - 8 Channel 1 RU Mixer
The Australian Monitor Installation Series MX81 mixer brings a range of new features
to the AMIS standard 1 RU mixer range. The MX81 mixer features the new Australian
Monitor Standard (AMS) input section which has an XLR input switchable between
mic & line level, dual RCA line inputs (on the first 6 inputs only), signal present LED
indication, individually switchable phantom power, & +/- 15dB of gain trim & treble &
bass controls available per input. The MX81 also boasts whisper quiet operation, 4
segment output level indication & balanced line output, record output & headphone
outputs. Optional remote VCA volume control, tone generators & muting boards are
also available for the MX81 (see options below). The MX81 mixer is extremely versatile
& represents excellent value for money.
•
•
•
•
•
•
•
•
8 input mono mixer
XLR input switchable between mic & line level
15dB +/- gain trim control per input
Input 1 is switchable to be pre/post master
24VDC or mains power operation
Optional remote VCA/Tone generator/ Muting boards
Whisper quiet operation
Dual color signal present indication LED per input
OPTIONS (not included)
AMMUTE1 Single Stage Priority Mute Module
• Allows for muting of channels 2 and higher when signal is present at channel 1 and the channel volume is turned up
AMMUTE3 Triple Stage Priority Mute Module
• Allows for muting of channels 2 and higher when signal is present at channel 1
• Allows for muting of channels 3 and higher when signal is present at channel 2
• Allows for muting of channels 4 and higher when signal is present at channel 3
• Ability to adjust threshold of the trigger signal along with the the release time of the ducked
signal
AMVCA Remote Master Volume Control Module
• Enables the end user to utilize a localized volume control
• Remote volume control is pre the mixers front panel master volume and thus can be
set up to give a limited volume range to the end user
• Optional RC1 remote volume control available
AMTONE1 Tone Module
• Generates four tones: Evacuation, Alert, Bell and Pre Announce Chime
page 15
MX81 SPECIFICATIONS
Frequency Response: 20Hz - 20kHz (+0,-3dB)
Distortion: > 0.1% @ 1kHz THD
Signal to noise ratio:
> 90dB (all pots at center)
Crosstalk: >70dB
Tone Controls:
BASS @ 100HZ +/- 12dB
TREBLE @ 10KHZ +/- 12dB
Sensitivity:
Mic Sens 4.36mV, -45dBu
(Trim in center 0dB) Imp 1k3ohm
Line Sens 0.775V, 0dBu
Imp >100k
RCA 200mV, -12dBu
Imp 30k Ohm
Max Level in:
XLR mic -15dBu line
+30dBu
RCA:
>30dBu
Max Level out:
+21dBu
Phantom Power:
15V DC
Master Out:
Nominal Level 0dBu into
1k Ohm Imp 100 Ohm
Mono Headphone Out:
Nom -6dB into 200 Ohm
Imp 10 Ohm
Mono Rec Out:
Nom -12dB into 10kohm
Imp 10k Ohm
Poxer Input:
AC: 115V/60Hz, 3 pin IEC320-C14
DC: 24 Volts
Power Consumption:
7 VA (max)
Fuses:
MAINS (115V) 120mA
Dimensions H x W x D:
1.75“x19”x7.2”
Weight:
Net 6.1lb
Shipping 3.75kg (8.3lb)
MX 82 - 8 Channel Stereo Mixer
The MX82 offers high quality audio performance and a wide array of features
in a standard 1RU size. There are four mic/line inputs and four stereo inputs.
Each of the four mic/line channels consists of a balanced XLR input switchable
between mic and line level, 15dB of gain trim across the mic/line inputs plus
individually switchable phantom power (15VDC). The first 4 channels also feature
a line level direct output which can be used to feed additional amplifiers, mixers
or recording devices. An internal dip switch allows the first 4 inputs to be routed
to the direct output, the master outputs or both. You can also feed the optional
tone generator to the direct outs if required. Input 1 can also be pre or post
master if you require, allowing it to be used as a priority (or emergency) input.
Inputs 5-8 are four dedicated stereo RCA aux/line level inputs.
• 8 input stereo mixer
• 4 XLR inputs switchable between mic and line level, each with
direct output
• 4 stereo dual RCA line level inputs.
• Each input has front panel mic/line switching (inputs1-4), treble
and bass control
• +/-15dB of gain trim
• dual color status LED indication
• Single master volume control
• Headphone output (can be pre/post master)
• Phantom power individually switchable for XLR inputs
• Priority muting via optional muting modules (see below)
• Optional remote VCA master and tone board
OPTIONS (not included)
AMMUTE1 Single Stage Priority Mute Module
• Allows for muting of channels 2 and higher when signal is present at channel 1 and the channel volume is turned up
AMMUTE3 Triple Stage Priority Mute Module
• Allows for muting of channels 2 and higher when signal is present at channel 1
• Allows for muting of channels 3 and higher when signal is present at channel 2
• Allows for muting of channels 4 and higher when signal is present at channel 3
• Ability to adjust threshold of the trigger signal along with the the release time of the ducked
signal
AMVCA Remote Master Volume Control Module
• Enables the end user to utilize a localized volume control
• Remote volume control is pre the mixers front panel master volume and thus can be
set up to give a limited volume range to the end user
• Optional RC1 remote volume control available
AMTONE1 Tone Module
• Generates four tones: Evacuation, Alert, Bell and Pre Announce Chime
http://amav.starin.biz
MX 82 SPECIFICATIONS
Frequency Response
20Hz - 20kHz (+0,-3dB)
Total Harmonic Distortion
<0.1% @ 1kHz
Signal to Noise Ration
> 90dB (all pots at center)
Crosstalk
>70dB
Tone Controls:
BASS @ 100HZ +/- 12dB
TREBLE @ 10KHZ +/- 9dB
Sensitivity Mic Sens 4.36mV, -45dBu
lmp 1k 3 Ohm (Trim center- 0dB)
Line Sens 0.775V, 0dBu
Imp >100k
RCA 200mV, -12dBu
Imp 30k Ohm
Max Level in:
XLR mic -9dBu line XLR line > 30dBu
RCA >30dBu
Max Level out:
+27dBu
Phantom Power:
15V DC / Internally Switched
Master out
Nominal Level 0dBu into 1k Ohm Imp 100 Ohm
Mono Headphone out:
Nom -6dB into 200 Ohm Imp 10 Ohm
Stereo Rec Out:
Nom -12dB into 10k Ohm
Imp 10k Ohm
Channel Direct Out:
Nom 0dBu into 1k Ohm
Imp 100 Ohm
Power Input: AC: 230V/50Hz or 115V/60Hz, 3 pin IEC320-C14 connector
Power Consumption (max): 7VA
Fuses:
MAINS (115V) 120mA
MAINS (230V) 63mA
Dimensions H x W x D:
1.75“x19”x7.2”
Weight:
NET 6.2lb
SHIPPING 8.4lb
MX 883 - 2RU Stereo Mixer
The MX883 is the latest MX mixer addition and is the most versatile and fully
featured mixer in the MX mixer family. The MX883 is a 2RU stereo mixer that
features 8 stereo RCA or mono XLR balanced inputs. Each input offers individually
switchable phantom power, +/-15dB of gain trim, balanced XLR switchable
between mic and line level, stereo RCA in. It also has line level direct outputs
which can be used to feed additional ampliers, mixers or recording devices, dual
color status LED indication, treble and bass controls and individual left, right and
aux assign switching with LED indication. The MX883 also features a link bus,
allowing two MX883 ís to be linked to form a 16 channel stereo mixer.Designed
to be a high performance stereo mixer with a separate auxiliary output bus for
added flexibility, the left and right bus outputs feature 5 band constant Q graphic
EQ and all outputs have 4 stage LED level indication. The MX883 also has a
pre/post master switchable headphone output. The MX883 is equally at home in
a commercial installation or in the demanding environment of live performance.
•
•
•
•
•
•
•
•
•
8 mic/line XLR/stereo RCA inputs with LED indication
Stereo output
Auxiliary output
5 band constant Q graphic EQ on L/R bus
Direct TRS output per input
+/- 15dB gain trim per input
Link bus
Low noise/high performance
2RU
page 17
MX 883 SPECIFICATIONS:
Frequency Response:
20Hz - 20kHz (+0,-3dB)
Total Harmonic Distortion:
< 0.1% @ 1kHz
Signal to Noise Ratio:
> 90dB (all pots at centre position)
Crosstalk Between Channels:
>70dB
Tone Controls:
BASS @ 100HZ +/- 12dB
TREBLE - @ 10KHZ +/-9dB
Sensitivity: (TRIM IN CENTRE 0dB)
- Mic Sens 4.36mV, -45dBu Imp
1k3ohm - Line Sens 0.775V,
0dBu Imp >100k - RCA 200mV,
-12dBu Imp 30kohm
Max Level In:
XLR mic -9dBu
XLR line >30dBu
RCA >30dBu
Max Level Out: +21dBu
Phantom Power: 15V DC
Outputs:Master Out - Nominal Level
0dBu into 1kohm
Imp 100ohm
Stereo Headphone Out:
Nom -6dBu into 200ohm
Imp 10ohm
Stereo Rec Out:
Nom -12dBu into 10kohm
Imp 10kohm
Channel Direct Out:
Nom 0dBu into 1kohm
Imp 100ohm
Power Input: AC: 230V/50Hz or
115V/60Hz, 3 pin IEC320 C14 connector
Power Consumption: (MAX) - 30 VA
Fuses: MAINS (115V) 200mA
MAINS (230V) 100mA
Dimensions:
3.5” W x 19”H x 10.6” D
Shipping Dimensions:
6.7” W x 19.9” H x 13.8” D
Weight: 8.8lb
PM12 - Performance Mixing Console
The Four Mono Channels include:
• Balanced XLR and 6.35mm TRS input
• 6.35mm TRS insert point on all mic
channels
• 48volt phantom power c/w LED indication
• Low cut filter
• Input gain trim
• 3 Band EQ with Sweepable mids
• EQ bypass switch
• 2 Aux Sends (one pre and one post fader)
• Pan control
• Channel Mute
• 4 segment LED channel metering
• Channel PFL c/w LED indication
The Four Stereo Channels include:
• Dual 6.35mm jack inputs
• Input Gain trim
• 3 Band EQ
• Pan control
• Channel Mute
• 4 segment LED channel metering
• Channel PFL c/w LED indication
Performance Mixing Console PM12
http://amav.starin.biz
PM12 Specifications
Frequency Response:
20Hz - 20kHz (+1/-2dB)
Distorion (TH & N):
0.01% @ +4 dBu, 1kHz,
bandwidth 80 kHz
Signal to Noise Ratio:
90dBu, all channels at
Unity Gain
Crosstalk (at 1 KHZ):
-70 dB between input
channels; -70dB between
input/output channels
Max Input:
Electronically balanced, discrete
input configuration
Mic E.I.N (22 Hz - 22 kHz):
-129.5 dBu, 150 Ohm source
-117.3 dBqp, 150 Ohm source
-132.0 dBu, input shorted
-122.0 dBqp, input shorted
Master Output:
+20 dBu balanced
Power Consumption:
7 VA (max)
Dimentions (HxWxD):
3.5”x13.2”x 17.2”
Weight:
Net 18.7lb
Shipping 23.1lb
Master Section Includes:
• Pre/Post Aux send controls
• Stereo Aux returns switchable to Stereo or
Alternate outputs
• Tape in/Record out
• Stereo Control room outputs c/w level
control
• Headphone output c/w level control
• Stereo 6.35mm Alternate jack outputs
• Alternate output fader
• Alternate output PFL c/w LED indication
• Balanced XLR/6.35mm jack Stereo main
outputs
• 2 x 10 segement L/R output LED indication
• L/R output faders
PM 16 - Performance Mixing Console
The Eight Mono Channels include:
• Balanced XLR and 6.35mm TRS input
• 6.35mm TRS insert point on all mic channels
• 48volt phantom power c/w LED indication
• Low cut filter
• Input gain trim
• 3 Band EQ with Sweepable mids
• EQ bypass switch
• 2 Aux Sends (one pre and one post fader)
• Pan control
• Channel Mute
• 4 segment LED channel metering
• Channel PFL c/w LED indication
The Four Stereo Channels include:
• Dual 6.35mm jack inputs
• Input Gain trim
• 3 Band EQ
• Pan control
• Channel Mute
• 4 segment LED channel metering
• Channel PFL c/w LED indication Performance
Mixing Console
PM16 Specifications
Frequeency Response:
20Hz - 20kHz (+1/-2dB)
Distortion (TH & N):
0.01% @ +4 dBu, 1kHz,
bandwidth 80 kHz
Signal to noise ratio:
90dBu, all channels at
Unity Gain
Crosstalk (at 1 KHZ):
-70 dB between input
channels; -70dB between
input/output channels
Max Input:
Electronically balanced, discrete
input configuration
Mic E.I.N (22 Hz - 22 kHz):
-129.5 dBu, 150 Ohm source
-117.3 dBqp, 150 Ohm source
-132.0 dBu, input shorted
-122.0 dBqp, input shorted
Master Output:+20 dBu balanced
Power Consumption: 7 VA (max)
Dimensions (HxWxD):
3.5” x 17.6” x 17.2”
Weight: Net 24.2lb
Shipping 28.6lb
Master Section Includes:
• Pre/Post Aux send controls
• Stereo Aux returns switchable to Stereo or Alternate
outputs
• Tape in/Record out
• Stereo Control room outputs c/w level control
• Headphone output c/w level control
• Stereo 6.35mm Alternate jack outputs
• Alternate output fader
• Alternate output PFL c/w LED indication
• Balanced XLR/6.35mm jack Stereo main outputs
• 2 x 10 segement L/R output LED indication
• L/R output faders
page 19
AMPLIFIERS
AMIS 120P - 120 Watt
70 Volt 8 Ohm Amplifier
Description - The AMIS120P is a 120 watt power amplifier with outputs for 4 and 8
ohms and 70 volt line. It may be desk or rack mounted. The AMIS120P features a flat
screwdriver accessible gain control on the rear panel. This amplifier features a status LED.
Inputs and Outputs - The AMIS120P features a balanced line level XLR
input with a parallel output to feed additional power amplifiers. The unit has
industry standard 3 pin XLR microphone sockets. The AMIS120P features 70
volt, 8 and 4 ohm isolated transformer outputs via a rear panel barrier strip.
Protection - Internal current limiting protects the amplifier from both overload and
overdrive conditions. Should the amplifier be overdriven, a current limiter will protect
the unit, and in a worst case scenario the amplifier will shut down until the problem
is resolved. Once the problem is fixed (shorted speaker line or overdriven input), the
amplifier will automatically reset and continue operation. The AMIS120P features
generous heatsinking. Australian Monitor Installation Series amplifiers feature a
protection network that provides greater stability and performance. Our amplifiers are
recognized worldwide for their reliability and this is due to the extensive levels of current
limiting which protect the amplifiers from both overload and overdrive conditions.
•
•
•
•
•
•
•
•
Balanced XLR line level input with parallel output
Signal Present LED
Rear panel level control
Temperature Sensing Fan Cooling
Current limiting protection
70V, 4 and 8 ohm outputs
2RU
120VAC/24VDC operation
http://amav.starin.biz
AMIS 120P SPECIFICATIONS
Power Output: 120 Watts RMS
Maximum Load: 40 Ohms @ 70 Volts
Power Bandwidth: 60Hz - 17kHz (- 3dB)
Frequency Response: 60Hz - 23kHz (- 3dB)
Total Harmonic Distortion: 0.5% @ 1kHz rated power
Signal To Noise Ratio: -80dB
Input Sensitivity: 700mV
Outputs: 70V, 4 Ohm, 8 Ohm
Controls: One gain control on rear
of the unit via flathead screwdriver control
Indicators: Power “on” LED
Power Source: 120VAC 60Hz 3 pin IEC connector; 24VDC
Power Consumption: 300 Watts
Protection: Current Limiter protection,
plus AC and DC fuses
Dimensions: 3.5” H x 19” W x 11” D
Weight: 26.5lb
AMIS 250P - 250 Watt
70 Volt 8 Ohm Amplifier
Description - The AMIS250P is a 250 watt power amplifier with outputs for
4 ohms and 70 volt line. It may be desk or rack mounted. The AMIS250P
features a flat screwdriver accessible gain control on the rear panel.
Inputs - TheAMIS250P features one signal input. The unit has industry standard 3 pin XLR
microphone sockets. Two line level sockets are provided for bridged in/out connection.
Outputs - The AMIS250P features 70 volt and 4 ohm isolated transformer outputs.
Protection - Internal current limiting protects the amplifier from both overload
and overdrive conditions. The AMIS250P also features protection in the form
of excess temperature auto cut out. A built-in auto temperature sensing fan will
turn on at a factory default level but in most situations, will never be required.
Australian Monitor Installation Series amplifiers feature a protection network
that provides greater stability and performance. Our amplifiers are recognized
worldwide for their reliability and this is due to the extensive levels of current
limiting which protect the amplifiers from both overload and overdrive conditions.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
6 balanced dual mic/line inputs
Overall bass, mid and treble controls
70V and 4, 8 ohm outputs
Vox muting from channels 1, 2 and 3 (selectable)
Vox triggered relay output
Temperature Sensing Fan Cooling
Tape Output (350mV @ 10K ohms) and balance output (700mv)
Bell, Pre Announce, Evac and Alert tones in-built (rear panel activation)
15V phantom power on all mic inputs (defeatable per channel by rear switch)
Insert point for connection of AMIS EQ or other processors
Overdrive protection and internal limiting
Signal Present LED
2RU
120VAC/24VDC operation
page 21
AMIS 250P SPECIFICATIONS
Power Output: 250 Watts RMS
Maximum Load: 20 Ohms @ 70 Volts
Power Bandwidth: 60Hz - 17kHz (- 3dB)
Frequency Response: 60Hz - 23kHz (- 3dB)
Distortion:
0.5% @ 1 kHz rated power (THD)
Signal To Noise Ratio:
80dB
Input Sensitivity: 700mV Outputs 70V, 4 Ohm
Controls: One gain control on rear of the unit via flathead screwdriver control
Indicators: Power “on” and “Protect” LED
Power Source: 120VAC 60Hz 3 pin IEC connector; 24VDC
Power Consumption: 400 Watts
Protection: Current Limiter protection,
plus AC and DC fuses
Dimensions:
3.5”H x 19”W x 13”D Weight:33.1lb
AMIS 1202P - 2 chan. 120 Watt 70 Volt 8 Ohm Amplifier
Description - The AMIS1202P is a dual channel 120W + 120W power amplifier designed to deliver
continuous full range performance in a compact and reliable package. The AMIS1202P is two independent
amplifiers in the one chassis making it the perfect choice for multi-zone or multi-channel applications.
Inputs and Outputs - The AMIS1202P provides dual balanced XLR inputs (male and female) per
channel. These two inputs are wired in parallel enabling a line level ‘split’ to be taken from the second
input of each channel. 70 volt line and 4/8 ohm outputs are available via the rear panel barrier strip.
Controls and Metering - A recessed input attenuation control for each channel is included on the rear panel.
These pots are accessible using a screwdriver. The AMIS1202P features a signal-present LED per channel and
power-on LED.
Protection - The AMIS1202P features ‘slow start’ and dual AC and DC fuse protection. Also featured is automatic
speaker protection. The AMIS1202P includes generous heat sinking for reliable operation in even the most
extreme conditions. Australian Monitor Installation Series amplifiers feature a protection network that provides
greater stability and performance. Our amplifiers are recognized worldwide for their reliability and this is due to
the extensive levels of current limiting which protect the amplifiers from both overload and overdrive conditions.
•
•
•
•
•
•
•
Balanced XLR line level input with
parallel output per channel
Signal Present LED
Rear panel level controls
Current limiting protection
70V, 4 and 8 ohm outputs per amplifier
2RU
120VAC/24VDC operation
http://amav.starin.biz
AMIS 1202P SPECIFICATIONS
Power Output: 120 Watts per channel
Maximum Load:
40 Ohms on 70 Volt line setting
Frequency Response:
60Hz - 23kHz (- 3dB)
Total Harmonic Distortion:
0.5% at 1kHz (1 Watt - full power)
Signal To Noise Ratio:
-80dB at 70V
-80dB at 8 Ohms
-80dB at 4 Ohms
Input Sensitivity:
0.5 Volt RMS - 70 Volt
Input Impedance:10K Ohms
Input Connection:
Active balanced input with male and
female 3 pin XLR input/output
Outputs:
70 Volt line and 4/8 Ohm via rear
panel barrier strip. Line out to feed
additional amplifiers from one of the
paralleled XLR input.
Controls:
Front power switch; Recessed rear
input attenuator (per chan)
Metering/Indicators:
Signal-present LED per chan.
Power Source: 120VAC 60Hz 3 pin
IEC; 24VDC
Power Consumption:
400 Watts (maximum)
Protection: Fuses for overload &
short circuit protect, High temperature
trip (at 120¼C), DC Output Sensing
(disconnects load if DC is present)
Dimensions: 3.5” H x 19” W x 11” D
Weight: 33.1lb
AMIS 480P - 4 Chan. 80 Watt
70 Volt/ 8 Ohm Amplifier
The Australian Monitor Installation Series AMIS480P is a robust, highly featured 4 channel power amplifier. Offering
4 independent channels, each delivering 80 watts into 4 ohms or 70/100 volt line, the AMIS480P is designed
to operate in extreme conditions to give the contractor the most reliable 4 channel amplifier available today.
Engineered with maximum attention to channel isolation, with individual ground lift switches and level control
for each channel, the AMIS480P will operate as 4 individual amplifiers in a rack space friendly, 2RU chassis.
For ease of installation, each channel input can be routed to the next channel via rear panel link
switches, eliminating the need for daisy chaining or Y-split cables. The AMIS480P also offers
signal present and clip LED indicators for each channel as well as a thermal protect indicator.
The AMIS480P is a significant advance in 4 channel amp design offered at a contractor friendly price.
•
•
•
•
•
•
•
•
•
4 x 80 watts @ 4ohm, 70 volt, 100 volt.
Bi colour status LED per channel
Thermal fault LED
2 x dual speed fans
230/240 VAC or 24 VDC operation
Ground lift switches per channel
Balanced XLR line inputs
Input link through switching
2 RU chassis
page 23
AMIS 480P SPECICIATIONS
Power Output:
4 x 80W
Freq. Response (1W): 80Hz - 20kHz
Distortion:
1% THD, all channels driven
Power Bandwidth: 85Hz - 20kHz
S/N Ratio: 94dB (ref 100V)
Crosstalk: 1kHz 80dB; 20Hz - 20kHz Better than 60dB
Input Sensitivity: 0.775V RMS (0dBu)
Input Impedance: 2
0K
Voltage Gain(pot at max):
100V out 129 (42dB)
70V out 90 (39dB) 4ohm out 23 (27dB)
Output Regulation: 95% (1kHz)
Dimensions:
4.36” H x 19” W x 17” D
Weight: 4
4lb
Shipping Weight: 53lb
ZONE PAGING SYSTEMS
Digipage
The AMIS Digipage is a 3 rack unit multizone paging and
source selection system that offers unprecedented flexibility for
multizone paging and source routing applications. 6 program
inputs and one dedicated local mic/line input are available to
each of 8 zone outputs.
With LED indication for program/local input selection,
zone output level, paging enable/disable and
network busy, the DigiPage provides extensive
status indication to the user. The DigiPage is also
expandable to 16 zones via a simple link cable to a
second unit. Paging stations are available in 8 or 16
zone models allowing paging into any individual zone,
any combination of zones or All Call. Remote control
panels are also available, allowing source selection
and volume control from within each remote zone.
DIGIPAGE SPECIFICATIONS:
Local Source:
Data/Digital Audio Mic: Unbalanced (RCA): Input RJ45 CAT5 Connector
Impedance:100KW; Program Sources (Trim Max.):
Sensitivity: 1.5V
Unbalanced (RCA): Input Balanced (XLR) MIC: Input Impedance:100KW; Impedance:1k3W; Sensitivity:150mV
Sensitivity:11mV
Balanced (XLR): Input Balanced (XLR) LINE: Input Impedance:1k3W; Impedance:45KW; Sensitivity:1mV
Min.Trim: -46dB
Sensitivity:350mV
Sum Input: Input Sensitivity:330mV;
Threshold: -46dBu (at output, ind.of input)
Frequency Response (3dB): 15Hz - 17kHz
THD: 0.005%
Noise: Page Mic: -84dB;
Other Inputs: -89dB
Power Supply 2:
4VDC 30VA Plug-pack
Dimensions:
5.2” H x 19.01” W x 6.7” D
Weight:
13.2 lbs.
Shipping weight:
15.4 lbs
Digipage Jr.
The DigiPage Jr starts as an 8 zone system
and can be expanded to 16 zones. It is
packed with excellent features and is a very
cost effective solution for those applications
who have neither the budget or the need for
the more elaborate features of DigiPage.
The Digipage Jr. is suitable for many similar applications as DigiPage
but has a few less inputs and does not allow for remote source or
volume selection.
DIGIPAGE JR SPECIFICATIONS:
Data/Digital Audio Mic: RJ45 CAT5 Connector
Program Sources (Trim Max.):
Unbalanced (RCA): Input Impedance:100KW; Sensitivity:150mV
Balanced (XLR): Input Impedance:1k3W; Sensitivity:1mV -57dbu
Min.Trim: -46dB
http://amav.starin.biz
Local Source:
Unbalanced (RCA): Input Impedance:100KW; Sensitivity: 1.5V
Balanced (XLR) MIC: Input Impedance:1k3W; Sensitivity:11mV
Balanced (XLR) LINE: Input Impedance:45KW; Sensitivity:350mV
Sum Input: Input Sensitivity:330mV;
Threshold: -46dBu (at output, ind.of input)
Frequency Response (3dB)
15Hz - 17kHz
THD 0.005%
Noise Page Mic: -84dB;
Other Inputs: -89dB
Power Supply 2
4VDC 30VA Plug-pack
Dimensions 5.2” H x 19.01” W x 6.7” D
Weight
9.9 lbs.
Shipping weight
12.2 lbs
ZM3 - Zone Paging Mixer
Description
The Australian Monitor ZoneMix3 is an extremely versatile and innovative mixer
and signal router. Featuring a broadcast quality audio spec, the ZoneMix3 allows
selection of 4 stereo sources to 3 stereo zones either at the ZoneMix3 or remotely.
One stereo source can have selectable priority per zone and each stereo zone
boasts 5 stage equalization. The ZoneMix3 also has the ability to route two
independent mic or line signals to any zone or combination of zones. Add to this
remote volume controls in each zone and the ZM3M 3 zone paging microphone
(both running via inexpensive CAT-5 cabling) and you have an extremely high
quality zone selecting mixer at a fraction of the cost of other products in this market.
Inputs
There are two MIC/LINE inputs. The balanced XLR inputs accepts mic level
signals. The dual RCA inputs accept line level inputs and are summed to mono
internally. Gain and EQ are controlled from the front panel. These inputs supply
15V phantom power, unless internally disabled. These inputs may have priority
over program inputs, if this feature is enabled.
There are four program inputs. These are stereo RCA line level inputs. Trim is
controlled from the front panel. LINE4 is a priority input, if this feature is enabled.
PAGE INPUT: There is an RJ45 connector on the rear of the unit accepts a CAT-5
cable from the optional ZM3M Paging Station.
SUM INPUT: This input has overall priority and is usually used for an emergency
tone or message.
Outputs
There are 3 Stereo Zone balanced XLR Outputs. The zone outputs are configured
as stereo left and right as default but can be internally changed to mono.
Link
Two ZoneMix3 Units can be linked together to provide six stereo zone outputs.
Controls
There are various levels of control you can use to ensure the optimum result
from your ZoneMix3. They include: Trim Control for all inputs 5 Stage EQ on
each zone output Mic/Line Selection for the first two inputs Program Control for
selecting a program source via the front panel. This can also be done remotely
with the ZM3R Remote Source/Volume Selection Unit.
page 25
ZM3 SPECIFICATIONS
Sensitivity (for 0dB out): Mic/Line Input (RCA) 86mV (-19dB);
Mic/Line Input (XLR) 1.55mV (-54dB);
Prog Input (RCA) 190mV (-12dB)
Max Level Out: 10V RMS (+22dB)
Frequency Response: 20Hz - 20kHz (0dB/-3dB)
THD: Less than 0.1%
Noise: -80dB
Crosstalk: Better than 65dB
Phantom Power: 15VD
Metering and Status:
A “status” LED gives an indication of OUTPUT signal.
It glows greenat 30dB and red
at 0dBV(1V). This is meant
to indicate clip within the
ZoneMix3. When used with Australian MonitorSynergy amplifiers, both LEDS on the
ZoneMix3 and the Synergy
amplifier will go red simultaneously Indicating
system clip (with pot at full
on the amplifier). A “remote”
LED indicates that the zone
is in remote control mode. A
“power” LED indicates there is power to the unit.
Power Input: 20VAC; 30VA
max.
Dimensions: 1.74” H x 18.9” W x 11.2” D
Weight: 5.5lb
Shipping: 6.6lb
ZRM4 - Zone Paging Mixer
Featuring 6 inputs that can be balanced XLR mic or dual RCA/balanced XLR line level, all available to any
combination of 4 zone outputs. Input one can be designated as a paging input with priority over all other inputs
individualy selectable at each zone output. Front panel switches with LED indication provide for simple routing
of each input. Each input has bi colour status LED indication & 2 stage equalization. Each input has an internal
gain trim which can provide a further +/- 15dB of gain to allow the perfect set up of input gain no matter what
the input signal may be. Phantom power & high pass filters are also supplied per input.
Each balanced XLR zone output also features a dual colour status LED & switchable paging mic priority. Remote
VCAs are also available for each output allowing for a wall mounted volume control to be installed in remote
zones giving a volume range from off to whatever the master level on the AMIS ZRM4 relevant zone output is
set to. Alert, Evacuation, Bell & Pre announce tones are also provided on board. The AMIS ZRM4 is a compact
yet extremely versatile zone routing mixer which makes the complex task of multizone signal routing simple &
cost effective.
•
•
•
•
•
•
•
•
•
•
•
•
6 universal inputs
+/- 15dB gain trim per input
4 balanced outputs
Input 1 has selectable priority
Individual output assign with LED
Switchable mic/line balanced XLR inputs
indication per input
Bi colour status LED per output
Bi colour status LED per input
Remote VCA volume control per output
HPF & 15 VDC Phantom power
On board Pre announce, bell, alert & evac
tones switchable per input
2 stage EQ per input
http://amav.starin.biz
ZRM4 SPECIFICATIONS
Sensitivity: (input for 0dBu out)
RCA In -26dBu to +4dBu (39mV to 1.23 V)
XLR Line In -26dBu to +4dBu (39mV - 1.23V)
XLR Mic In -60dBu to -30dBu (0.78mV to 25mV)
Max Level In: >14.1 Vrms (+25dBu)
Max Level Out: >15.4 Vrms (+26dBu)
Frequency Response: <5Hz to >22kHz (0dB/-3dB)
THD: Less than 0.1%
Noise: <90dBu 20Hz-20kHz (all pots centered)
Crosstalk: <-65dB @ 1kHz
Phantom Power:
15VDC
Power Input: 20VAC; 600mA max or
24 to 34v DC regulated 600mA max
Dimensions: 44.0h x 482.0w x 188.0d
Weight: 6.4lb
Shipping: 9.7lb
Mym series
MYM-DCD - Dual CD player
•
•
•
•
•
•
1 RU dual program source
MP3 compatible CD player
Option IR control for the CD player
Up to 20 tracks programmable on the players
Discrete stereo outputs for each module
Priority stereo output as standard
MYM-TCD - CD player and Tuner
•
•
•
•
•
•
•
•
1 RU dual program source
MP3 compatible CD player
Option IR control for the CD player
Up to 20 tracks programmable on the CD player
10 user selectable presets on the AM/FM tuner
Discrete stereo outputs for each module
Priority stereo output as standard
Tuner sleep function
MYM-DT - Dual Tuner
•
•
•
•
•
1 RU dual program source
10 user selectable presets on each AM/FM tuner
Discrete stereo outputs for each module
Priority stereo output as standard
Tuner sleep function
page 27
SPECIFICATIONS CD/MP3 PLAYER
Output Level:
@ 1kHz, 0dB 1.2V +/- 0.3V
Frequency Response:
20Hz-20kHz +/- 2dB
Separation:
1kHz, 0dB >60 dB
T.H.D+ Noise:
1kHz, 0dB <0.05%
Weight 5kg
SPECIFICATIONS CD/MP3 PLAYER
Output Level:
@ 1kHz, 0dB 1.2V +/- 0.3V
Frequency Response:
20Hz-20kHz +/- 2dB
Separation: 1kHz, 0dB >60 dB
T.H.D+ Noise: 1kHz, 0dB <0.05%
AM / FM TUNER:
FM Tuning Range: 87.5 MHz -108 MHz
IF Frequency & Rejection:
10.7 MHz >80 dB
Image Rejection >25 dB
S/N Ratio 1mV/M Input 46db
T.H.D 1mV <1.0%
Auto Tuning Sens: <50uV
AM Tuning Range: 522kHz – 1620kHz
IF Frequency & Rejection:
450 kHz >45dB
Image Rejection: >30dB
S/N Ratio 5mV/M Input >35dB
Auto tuning sens: <2mV
Dimensions: 18.97” W x 1.73” H x 9.84” D
SPECIFICATIONS AM / FM TUNERs
FM Tuning Range: 87.5 MHz -108 MHz
IF Frequency & Rejection:
10.7 MHz >80 dB
Image Rejection: >25 dB
S/N Ratio: 1mV/M Input 46db
T.H.D: 1mV <1.0%
Auto Tuning Sen: <50uV
AM Tuning Range: 522kHz – 1620kHz
IF Frequency & Rejection: 450 kHz >45dB
Image Rejection: >30dB
S/N Ratio: 5mV/M Input >35dB
Auto tuning sens: <2mV
Dimensions: 18.97” W x 1.73” H x 9.84” D
Equalizers
AMIS 215EQ - 2 Channel 15 Band Equalizer
The Australian Monitor Pro Series AMIS 215EQ is a single rack unit graphic
equalizer. Featuring constant Q circuitry, selectable 6dB or 12dB slider range,
balanced XLR, 6.35mm TRS & unbalanced RCA inputs & outputs, EQ bypass
switches, ground lift switches, output level controls & overload LED’s.
AMIS 31EQ - Single Channel 31 Band Equalizer
The Australian Monitor Pro Series AMIS 31EQ is single rack unit graphic
equalizer. Featuring constant Q circuitry, selectable 6dB or 12dB slider range,
balanced XLR, 6.35mm TRS & unbalanced RCA inputs & outputs, EQ bypass
switches, ground lift switches, output level controls, overload LED’s & variable
high & low pass filters.
The features found in Australian Monitor Pro Series graphic EQ’s are usually
associated with equalizers many times the price of these. The AMIS 215EQ
and AMIS 31EQis an extremely well featured graphic equalizer at a contractor
friendly price.
http://amav.starin.biz
EQUALIZER
AMIS215EQ: 2 x 15 2/3 Octave
ISO Spacing from 20Hz – 20kHz
AMIS31EQ: 31 1/3 Octave ISO
Spacing from 20Hz - 20kHz
Type Constant Q Accuracy 3%
Center Frequency
Travel 20mm Positive Centre
Detent Range +/- 6dB or +/12dB selectable
Inputs:
Type Active balanced/unbalanced
Connectors 3 pin XLR, 6.35mm
TRS balanced, RCA unbalanced
Impedance 20k Ohms balanced,
15k Ohms unbalanced
Max level +22dBm (level control
at centre)
Outputs:
Type Active balanced/unbalanced
Connectors 3 pin XLR, 6.35mm
TRS balanced, RCA unbalanced
Impedance <150 Ohms Typical
Max Level +22dbm (2k ohms)
+18dBm (600 ohms)
RFI Filters: Yes
Passive Bypass Switches: Yes
Overload LED Switches 5dB
below clipping
Low Cut Filter: (AMIS31EQ only)
10-250Hz, 12dB per octave
High Cut Filter: (AMIS31EQ
only) 3kHz-40kHz, 12dB per
octave
Frequency Response 20Hz20kHz
IM Distortion(SMPTE) 0.005%
Signal to Noise Ratio -94dB
(20kHz noise bandwidth)
Channel Separation 50dB
Common Mode Rejection: 50:1
Voltage: 110VAC 60Hz
Dimnesions:
1.75” H x 19.01” W x 8.50 D
Weight:
5.51lbs
Crossover / Compressor Limiter
AMIS 23x - 2 Way Crossover
AMIS23X SPECIFICATIONS
Frequency Range:
X1 80Hz to 920 Hz
X2 800Hz to 9.2 kHz
Hum and Noise: >93dBu
Low Frequency Section: Output @ 0dB <-106 dBu
High Frequency Section: Output @ 0 dB <-97d dBu
Signal-To-Noise Ratio: 118 dBControls:
The Australian Monitor Pro Series AMIS23X is a one rack unit, fourth order LinkwitzRiley electronic crossover. The AMIS23X can be confi- gured as either a stereo two
way or a mono three way crossover. Featuring clip LED indication per band per
channel, frequency range selector switch, CD horn boost switch & polarity reverse
switching, the AMIS 23X is a professional price-performing crossover.
CL2 - Compressor Limiter
The Australian Monitor Pro Series AMIS CL2 is a 1 RU, dual channel compressor
limiter. Featuring an expander/gate, compression & limiting per channel, the
AMISCL2 utilizes a high quality VCA to give excellent performance from a budget
priced dynamics processor. With added features like selectable Automatic attack &
release times & EQ enhancement which automatically compensates for high end
loss when heavy compression is taking place, the AMISCL2 has the features & the
performance of a compressor/limiter many times the price.
page 29
Input Level Continuously variable; Output Level Low, High Cont. variable;
CD Boost Rear panel switch; mute Front panel switch; Channel link Rear panel switch; Phase Rear panel switch
Dimensions:
1.75”H x 19”W x 8.5”D
Weight: 5.5 lbs
AMIS CL2 SPECIFICATIONS
Input:
Type RF-filtered, Servo-
balances input stage
Impedance 60K balanced
Nominal Operating Level -
10dBu to 4dBu
Maximum Input Level: +21dBu balanced and unbalanced
CMR: @ 1kHz >40dB
Input detection:
Type DC de-coupled, unbalanced input
Impedance >20K ohms
Maximum Input+21dBu
Output:
Type Electronically buffered output stage
Impedance <40 ohms
Bandwidth: 5Hz to 50kHz, +0, -1dB
THD: @ +4dBu 0.05%typ..
IMD (SMPTE) @ +10dBu 0.01% typ.
Noise & Hum: >93dBu
Crosstalk:
@ 20kHz >85dBu
CONTRACTOR TOOLS
Multican (HA4) 4 Channel Headphone Amplifi
er The AMIS MULTI CAN is a compact yet
high quality 4 channel headphone amplifi
er, featuring 6.35mm TRS, dual RCA and
dual XLR stereo inputs and 6.35mm TRS
headphone outputs the MULTI CAN also offers
individual output level controls per channel.
Juiced Up (PPA2) Dual Phantom Power
Supply is an in-line power supply that provides
phantom power for 2 condenser mics. Selectable
between 12VDC & 48VDC, it will power nearly
any commercially available microphone. The
AMIS PPA2 can run off 29 volt batteries or be
powered by the supplied 12 VDC power supply.
Get Up Converts an unbalanced domestic level
signal to a professional line level balanced audio
signal. Inputs are stereo RCA connectors and
outputs are balanced XLRs. The GET UP also
features a front panel level control for achieving
the optimal output level.
Get Down Converts a professional line level
balanced audio signal to an unbalanced
domestic level signal. Inputs are balanced XLRs
and outputs are stereo RCA connectors. The
GET DOWN also features a front panel level
control for achieving the optimal output level.
Let’s Split (MSC1) Microphone Splitter /
Combiner produces 2 balanced XLR signals,
(1 direct, 1 transformer isolated) from a single
balanced XLR input. The AMIS MCS1 provides
a ground lift switch to eliminate hum.
Let’s Split (LSC1) Line Splitter / Combiner
produces 2 balanced XLR signals, (1 direct, 1
transformer isolated) from a single balanced
XLR line level input. The AMIS LSC1 provides
a ground lift switch to eliminate hum.
http://amav.starin.biz
Mixed Up (PM4) 4 Channel Passive Mixer
is a 4 input, 1 output passive mixer that can
be used for mixing 4 mics, instruments, or
line sources or forconverting stereo feeds to
mono. The AMIS PM4 requires no batteries or
other external power source. The unit features
unbalanced .25 inch jack inputs & outputs and
can be used as a 1 in 4 out signal splitter when
all channel volumes are run at maximum.
Injector (DI1) Passive Direct Injection Box
features a balanced XLR output, a .25 inch
TRS through output, 3 stage pad offering up
to 40dB of attenuation & a ground lift switch for
hum elimination.
Pre Me (PRE1) Mini Microphone Preamp
features balanced XLR & unbalanced 6.35mm
jack inputs & outputs, switchable 36 volt
phantom power, gain control & signal clip LED.
Powered by a supplied 12VDC power supply,
Buzz Off (HE2) Dual Hum Eliminator tool
for eliminating hum & signal noise caused
by ground loops. The AMIS HE2 has two
discreet signal paths via balanced XLR inputs
& outputs. The AMIS HE2 is a passive device
& can also be used as a converter of balanced
& unbalanced signals. As part of the AMIS
Contractor Tools range, the AMIS HE2 is an
inexpensive
Drop Me 70 volt to line level converter with
phoenix to XLR and level control.
AMIS26 2 x 6 Mic/Line Distribution Amplifier. 24VDC
Phantom Power switchable per input. Either input
can be routed to any of the 6 outputs via front panel
dip switches.
MP8 8 Channel Monitor Panel. 100/70V Line or
Low Impedance Applications. Includes 2.5 inch
speaker with volume control. Loop in, loop out
terminal strips for inputs from amplifiers and
outputs to speakers.
DMA1 digital message announcer is a compact yet
highly featured digital playback device. Utilizing an
SD card digital storage format the DMA1 delivers
high quality stereo audio in an MP3 format.
page 31
Speakers
ST30P - Active two-way stereo speakers
The AMAV ST30P is supplied in pairs. The master features an on board 30W stereo amplifier with treble,
bass, volume control, a stereo line input via RCA connectors and a speaker output to provide power to the
passive speaker.
The compact & architecturally pleasing AMAV ST30P delivers high quality reinforcement for a variety of
audio visual applications.
• On board stereo power amplifier
• 30 watt RMS
• Complete with “U” brackets
• Stereo RCA inputs
• Bass, Treble and Volume controls on board
• Available in black
• Supplied as pairs (one passive, one active)
• High quality sounds reproduction
Avaliable in white
http://amav.starin.biz
ST30P SPECS
Woofer Diameter:
5.25”
Woofer Impedance:
8ohm
Tweeter Diameter:
0.5” dome
Tweeter Impedance:
8 ohm
Power: 30 Watts
Sensitivity: 89dB
Frequency Response:
60Hz to 20kHz
Active Speaker Specs
Equalization:
50Hz shelf ±15dB
10kHz shelf ±12dB
AC Power Input:
120 VAC
Dimensions:
9.65”W x 7.20”H x 6.54”D
Weight: 13.2 lbs per pair
XRS - Two-way speakers
The XRS series of high performance loudspeakers takes legendary performance and adds a more stylish,
contemporary look that is at home in any entertainment environment.
The XRS series two-way injection moulded speaker enclosures have more features and new aesthetic to suit live
sound reinforcement and permanent installation. From front-of-house to fold back, the dance floor to background
fill, the XRS series is designed with flexibility and performance in mind.
Including 8”, 10” and 12” models, each have high quality compression drivers and represent a significant advancement
in injection moulded box design while maintaining excellent audio quality and great value for money.
XRS8
Two way loudspeaker, 8” woofer & 1.5” horn with 90 x 90 (h x v) dispersion.
Heavy duty, injection moulded black case. Includes U mounting bracket.
XRS8 SPECS
Driver: 1 x 8” woofer, 1 x 1.5” HF driver
Woofer Impedance: 8 Ohm
Recommended Max Power: 100 W
Sensitivity: 92dB
Frequency Response (-3dB): 65Hz to 18kHz
Frequency Response (-10dB): 60Hz to 20kHz
Dimensions: 10.9”W x 10.11”D x 15.75”H
Weight: 14.33 lbs
XRS10
Two way loudspeaker, 10” woofer & 1.5” horn with 90 x 90 (h x v) dispersion.
Heavy duty, injection moulded black case with pole mount & eye bolt
installation points.
XRS10 SPECS
Driver: 1 x 10” woofer, 1 x 1.5” HF driver
Woofer Impedance: 8 Ohm
Recommended Max Power: 250 W
Sensitivity: 95dB
Frequency Response (-3dB): 55Hz to 18kHz
Frequency Response (-10dB): 50Hz to 20kHz
Dimensions: 12.64”W x 8.18”D x 18.27”H
Weight: 22.05 lbs
XRS12
Two way loudspeaker, 12” woofer & 2” horn with 90 x 90 (h x v) dispersion.
Heavy duty, injection moulded black case with pole mount & eye bolt
installation points.
XRS12 SPECS
Driver: 1 x 12” woofer, 1 x 2” HF driver
Woofer Impedance: 8ohm
Recommended Max Power: 300 W
Sensitivity: 97dB
Frequency Response (-3dB): 50Hz to 18kHz
Frequency Response (-10dB): 40Hz to 20kHz
Dimensions: 16.34”W x 15.04”D x 24.40”H
Weight: 39.68 lbs
MICROPHONES
Astatic GSM-1
Heavy-Duty Installation Shockmount
• Hi mass for maximum shock absorption
• No”sag” or “droop”, even when using longer gooseneck microphones
Astatic 827A-13, 827A-17
Cardioid Mini Gooseneck Condenser Microphones
• Unidirectional for rejection of feedback or unwanted ambient
sounds
• Unique all flex gooseneck design for precise positioning
• Low noise transformerless electronic design
• Includes foam pop filter
Astatic 40-118
Hi Mass, Heavy-Duty Portable Desk Stand with LED
• Large, soft-Touch programmable membrane switch with LED
• LED Status indicator on electronically noiseless switch
• Selectable Push-To-Talk or Push-To-Mute (-55dB)
• Selectable power up ON or power up MUTED
Astatic AMC105SNO-19
Dynamic Heavy Duty Push-To-Talk Omni-Directional Microphone (19” Gooseneck)
• Frequency Response 50Hz to 13kHz
• Internal shock mount
• Switch wired normally open
• 5/8”-27 mounting thread, 2-3/4” flange & 7’ jacketed four conductor cable
Astatic 119S-19
Dynamic Heavy-Duty Cardioid Paging Microphone Head (Chrome, Push-To-Talk
Switch, 19” Gooseneck)
• Frequency response 80Hz to 15kHz
• Internal shock mount & multi-stage blast (“pop”) filter
• Includes attached 5.5’ two conductor shielded cable & 2-3/4” flange
Astatic 611L
Dynamic Omni-directional Palm Held Microphone
• Rugged polyester mic element resists effects of extreme temperature, moisture, most
acids, alkaline & solvents
• Low impedance for long canle runs and hum resistance
• Molded high impact resistant Cycolac body
• 75,000 cycle switch
• Permanently attached heavy duty, 4-conducter, 2-shielded, coiled chord with stripped &
tinned ends
• Included panel mount hanger-clip
Astatic 631L
Dynamic Noise Canceling Palm Held Microphone
• 360° elimination of background noise and resists feedback
• Soft curved lip guard to encourage proper spacing for best up-close use
• Other features same as 611L
http://amav.starin.biz
page 35
5 year warranty with every Australian Monitor purchase.
Distributed exclusively in the U.S. by
Reseller Portal for Pricing, Programs and Product Details:
http://AustralianMonitor.Starin.biz
STARIN© 2009: Documents created and distributed by Starin are for the sole purpose of presentation and promotion of Starin
products. No editing, duplication or other modification is permitted. The material should be presented in whole. Authorized Starin
representatives may use the material in so far as it benefits Starin and their mutual interests. Anyone provided this material will
use their best abilities to keep from having it distributed to competitors of Starin. The Starin logo and copyright statement must
remain fixed to the content. Any representations that this material belongs to or is associated with another firm are not permitted.
Starin-Australian-Guide-10-20-2009
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement