IBT-5 Quick and easy testing for installation, commissioning and

IBT-5 Quick and easy testing for installation, commissioning and
ACTERNA TEST & MEASUREMENT SOLUTIONS
IBT-5
Quick and easy testing for installation, commissioning and
maintenance of ISDN basic rate accesses
Key Features
• Low-cost, rapid installation of ISDN lines and equipment
for the basic rate access
• Automated testing of services/teleservices and ETSI
supplementary services for trouble-free commissioning
• Efficient management and maintenance of ISDN accesses
with simulation on all major interfaces and wide range
of protocols
• Simplified use with intuitive interface, mobile phone-style
navigation, downloadable updates and phantom power-feed
• Enhanced troubleshooting with offline and online data
analysis tool and step-by-step guide to testing procedures
Easy, low-cost testing and maintenance
Rapid and assured testing of integrated services digital network (ISDN) access is
vital for network providers to deliver new and highly reliable voice and data
services over the growing number of public, private and proprietary protocols and
interfaces. But with the mix of technologies becoming increasingly complex,
highly functional testers that are easy and cost-effective to use are needed to
enable configurations to be tested and issues resolved so that quality and
reliability can be assured.
WEBSITE : www.jdsu.com
IBT-5
2
The IBT-5 provides a single solution for
rapid and reliable performance testing
and fault diagnostics in all environments
B1
01101101
10110110
ISDN
S/T BRA
IBT-5 Tester
1
S
3
5
6
8
9
8
The JDSU IBT-5 is a low-cost, handheld tester for installing, commissioning and
maintaining ISDN basic rate accesses and public and private PBX networks. Easy
to use with clearly displayed results the IBT-5 provides a single solution for rapid
and reliable performance testing and fault diagnostics in all environments, with a
robust, compact design and extended eight-hour battery life.
NT1
P
2
4
7
7
Yes
No
Clr
9
Shift
10110110
01101101
B2
Self-call mode
ISDN
S/T BRA
IBT-5 Tester
1
P
2
4
S
3
5
7
6
8
7
9
8
9
Yes
NT1
ISDN
S/T BRA
IBT-5 Tester
NT1
No
1
P
2
4
S
3
5
7
6
8
7
9
8
Clr
Yes
No
Clr
9
Shift
Quality access and services
The IBT-5 enables users to quickly and easily check accesses to the ISDN network,
the availability of standard and supplementary services and teleservices, and the
resulting transmission quality.
Shift
BERT Mode
Low-cost, rapid installation
The IBT-5 provides all the tests and functions required for the installation of basic
rate accesses, including bit error rate test (BERT) testing of the physical layer and
transmission quality and X.25 testing in the D channel for packet transmission
evaluation.
Loopbox Mode
01101101
10110110
01101101
10110110
B1 or B2
End-to-end measurements
All major protocols (including Q.SIG, CorNet-T, CorNet-TS, and TN1R6) and
interfaces (So/To, and U (2B1Q/4B3T)) are supported.
In BERT testing the IBT-5 can test the quality of transmission in self-call mode or
through end-to-end measurements. Bit errors can be inserted manually and the
level of quality displayed at any time during the test.
Availability of the service
Transmission
integrity
X.25
ISDN
S/T BRA
IBT-5 Tester
So/To
Yes
No
Clr
Shift
IBT-5
X.25
Test of X.25 services
NT1
ISDN
U
X.25
To evaluate X.25 quality the IBT-5 establishes an X.25 link (by self-call or via a
loop) and analyzes the reception quality of a previously transmitted data packet.
The tester indicates the availability of the service and the integrity of data
transmissions, and includes a loopback function for complete testing.
The IBT-5 also enables testers to troubleshoot problems arising from the ISDN
connection by displaying, storing and analyzing a call trace using the Real-Time
Trace Windows™ PC Detailed Decoder software.
Decoder software
IBT-5
3
ISDN
S/T BRA
IBT-5 Tester
1
P
2
4
S
3
5
7
6
8
7
9
8
Yes
No
Clr
9
Shift
IBT-5
?
EDSS-1
Speech BC
Audio 3,1 kHz
Data 64 BC
S /T
U
Data 56 BC o o NT1
Speech
Fax G3
Fax G4
Teletex
Videotext
ISDN
Available for EDSS-1, EDSS-CH (SN3), 1TR67 and VN6 protocols the IBT-5
enables users to launch an automatic test to check for the presence of
supplementary services on the basic access being tested. With the choice of
services tested depending upon the services implemented in the network the IBT5 avoids the risks of incorrect results caused by unnecessary tests, and indicates
the availability, non-availability and/or causes for error for each tested service
Test of services and teleservices
ISDN
S/T BRA
IBT-5 Tester
1
P
2
4
S
3
5
7
6
8
7
9
8
Yes
No
Clr
9
Shift
IBT-5
?
CLIP
CLIR
COLP
SUB
AOC
TP
HOLD
CFU
CFB
CFNR
CUG
MCID
UUS
So/To
U
NT1
ISDN
ISDN
S/T BRA
IBT-5 Tester
Yes
No
Clr
Shift
So
To
ISDN
S/T BRA
IBT-5 Tester
Yes
No
Clr
Shift
PBX
Line simulation mode (LT)
IBT-5 So
ISDN
S/T BRA
IBT-5 Tester
1
P
2
4
S
3
5
7
6
8
9
8
Yes
No
Clr
9
Shift
So/To
U
NT1
ISDN
U
ISDN
S/T BRA
IBT-5 Tester
1
P
2
4
S
3
5
7
6
8
7
9
8
9
Yes
No
Clr
Shift
IBT-5 So and U
Terminal simulation mode (TE)
Facilitated maintenance
Simulation (TE and LT) on all major interfaces (So/To and U (2B1Q/4B3T))
enables efficient management of ISDN accesses, with simulation of Q.SIG,
CorNet-T, CorNet-TS or TN1R6 protocols for inter-PBX testing also fully
supported.
The IBT-5’s LT simulation function provides an easy means of simulating the
ISDN network before connecting equipment such as a PBX. Additional to TE
simulation this operating mode enables testers to use existing tests and functions
such as call, automatic test of services, teleservices, BERT test and loopback.
Test of supplementary services
7
Easy commissioning
The IBT-5 automatically tests the availability of the various ISDN services offered,
including bearer capability, services/teleservices and ETSI supplementary services.
A special mode enables the service and its associated protocol to be tested
automatically.
IBT-5
4
Header-Section Head (optional)
Simplified use
The IBT-5 can be used just like an ordinary DTMF/touch tone telephone. The
tester features clear scrolling menus for each test, prompting the user to enter
specific data as and when required, and enabling testers to save data for future
tests. All test results are provided in plain text and can be printed on any serial
printer (figure 1).
The IBT-5 can repeat the last test sequence (recall), with a built-in memory for
storing six numbers. The tester also displays information on the cost of the call,
calling number and calling errors. In the event of connection failure testers can
track the source and location of the problem using a simplified protocol trace
(figure 2).
The IBT-5 is easily updated with new software in minutes, either by download or
by exchanging a chip (FLASH).
Enhanced troubleshooting
Compatible with all JDSU’s testers, the JDSU ISDNpartner Expert System enables
information and statistics generated by the equipment to be downloaded for more
detailed analysis by PC-based applications. Using the software solution, testers
can analyze data on the D channel in realtime, examining logs and statistics and
tracking for recurring errors so that long-term corrective action can be taken.
The software solution provides an HTML interface that guides testers through the
testing process whatever their level of skills and experience, reducing the need for
specialist staff to detect and correct common ISDN problems. Automatic
diagnosis and suggested corrective actions are offered, as well as a sophisticated
process for navigating the trace for complex faults, increasing the speed at which
problems are isolated and resolved (figure 3).
figure 1 Protocol trace
figure 2 Scrolling menus
figure 3 Event log screen
IBT-5
Specifications
So/To basic rate access
Test features
Electrical characteristics to
Rec. ITU-T I.430, ETS 300 012
Connector
1 x RJ-45
Impedance
high impedance, 100 Ω
Protocols: EDSS-1, Q.931, BTNR 191,V1, Q.SIG, 1TR67,TN1R6,
1TR6,TPH1962,VN3/VN4/VN6, SN2, EDSS-CH (SwissNet 3),
DMS-100 (funct.), N.ISDN, ATT, NTT, CorNet-T/TS®,Telenokia,
Televerket
Interface
auto-configuration, point-to-point,
point-to-multipoint, no protocol (leased line mode)
Coding law
A, µ
Display
2 lines x 16 characters, backlit
Keypad
16 keys
Dimensions (w x h x d)
240 x 45 x 55 mm
Weight of the basic instrument
approx. 0.5 kg
Serial interface
jack connector
Telephone function
(TE simulation and option for LT simulation)
Selection
address, sub-address,
channel, service, self-call
Phone-book
6 telephone numbers
Recall facility
Keypad facilities test
on connection
DTMF generation
0 to 9, *, #
Dialling
overlap or “en bloc”
Interpreted trace
layers 1, 2, 3
Network charge analysis keypad
and functional protocols
Screen display
Information on the current call, called address, calling address,
connected address, billing
statement, service, channel, reason for non-display of the
address, cause of connection failure and location parameter,
Call Waiting display, DISPLAY information element
Bit error rate test
Analysis to G.821 (ITU-T Blue Book)
Pseudo-random bit sequence
211–1
Measurement time
1 min, 15 min, 1 h, 24 h, infinite
Manual insertion of bit errors
Automatic test of services
Predefined tests
Bearer capability, teleservices
Loopbox mode (B1 and B2)
Selection mode
ISDN (all incoming calls or
user-to-user signaling)/X.25 in the D channel
Realtime trace on PC
Detailed decoding of D-channel signaling on a PC
Result printouts
Results from various measurements with the IBT-5 can be
printed directly on a printer with an RS-232 serial interface.
U interface (BN 7522/1X and BN 7522/7X)
Connector
Layer 1 characteristics
Line code
2-wire
conform to ANSI, ETSI
2B1Q, 4B3T
®Registered trademark, Siemens AG Munich/Berlin
General specifications
Menu languages
French, English, German, and Spanish
Power supply
phantom power or rechargeable batteries (option)
Operating time from NiMH batteries
> 8 hours
Charging time
< 3 hours from AC line
Safety
to EN 60950
Drop and shock test
to ETS 300 019-2 class 7M2
Permitted ambient temperature
to ETS 300 019-1 class 7.1
Operational range
–5 to +50°C
Storage and transport range
–25 to +70°C
Humidity
20 to 80% relative, 525 g/m3 absolute
Commissioning
– Testing of all supplementary services
(EDSS-1,VN6, 1TR67, SN3)
automatic mode
– Test of X.25 in the D channel (layers 1, 2 and 3)
– Set-up of an X.25 connection (SAPI 16)
– Transfer of a data packet
– Checking for correct data transmission
– Generic functional protocol
CFU, CFB, CFNR
Option: Rechargeable battery pack
including LT simulation
This option is highly recommended for configuring and commissioning ISDN equipment in a network.
Protocols
EDSS-1, Q.SIG, Q.931, 1TR6,
1TR67, EDSS-CH(SN3),VN3/VN4/VN6,TPH1962,
Telenokia,Televerket
Telephone function, BERT (bit error rate test), automatic
testing of services and teleservices, loopback function.
Ordering information
IBT-5 basic instrument
S0/T0 interface
BN 7522/20
S0/T0 and U (2B1Q) interfaces
BN 7522/10
S0/T0 and U (4B3T) interfaces
BN 7522/70
Standard package includes:
– Operating manual
– Quick User Guide
– Carrying bag
– Test cables for the S0/T0 and U (2B1Q) or U (4B3T) interfaces.
Menu available in:
– English
– French
– German
– Spanish
IBT-5 complete packages
– IBT-5 S0/T0 and U (2B1Q) BN 7522/11
– IBT-5 S0/T0 and U (4B3T) BN 7522/71
Includes IBT-5 basic instrument (S0/T0 and U interfaces), all
software options and rechargeable battery pack option with
serial interface (NiMH cells with universal charger).
Standard package includes:
– Operating manual
– Quick User Guide
– Carrying bag
– Test cables for the S0/T0 and U (2B1Q) or U (4B3T) interfaces
– Decoding software on PC.
All statements, technical information and recommendations related to the products herein are based upon information believed to be
reliable or accurate. However, the accuracy or completeness thereof is not guaranteed, and no responsibility is assumed for any
inaccuracies. The user assumes all risks and liability whatsoever in connection with the use of a product or its application. JDSU reserves
the right to change at any time without notice the design, specifications, function, fit or form of its products described herein, including withdrawal at any time of a product offered for sale herein. JDSU makes no representations that the products
herein are free from any intellectual property claims of others. Please contact JDSU for more information. JDSU and the JDSU logo are
trademarks of JDS Uniphase Corporation. Other trademarks are the property of their respective holders. ©2006 JDS Uniphase
Corporation. All rights reserved. 30137154 500 0206 IBT5.DS.ACC.TM.AE
Test & Measurement Regional Sales
NORTH AMERICA
TEL : 1 866 228 3762
FAX : +1 301 353 9216
LATIN AMERICA
TEL : +55 11 5503 3800
FAX : +55 11 5505 1598
ASIA PACIFIC
TEL : +852 2892 0990
FAX : +852 2892 0770
EMEA
TEL : +49 7121 86 2222
FAX : +49 7121 86 1222
WEBSITE : www.jdsu.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement