Trendnet TEW-636APB N300 Wireless Hot Spot Access Point Quick Installation Guide
Add to my manuals
10 Pages
Trendnet TEW-636APB is a high-speed wireless access point that allows you to create a secure wireless network for your home or small office. With speeds of up to 300Mbps, it's perfect for streaming HD video, gaming, and other bandwidth-intensive activities. It also features multiple virtual access points (VAPs), so you can create separate networks for guests or different devices. The TEW-636APB is easy to set up and manage, and it's compatible with all wireless devices.
advertisement
Quick Installation Guide
TEW-636APB
H/W: V1.0R
Français .....................................................................................................
1. Avant propos ......................................................................................
2. Installation du matériel .......................................................................
3. Configuration du point d'accès ...........................................................
2
3
1
1
Troubleshooting ........................................................................................ 6
Version 03.24.2008
1. Avant de commencer
Contenu de l'emballage
Adaptateur secteur (12V DC, 1A)
Configuration du système
(5.5 ou plus receint)
Application
300Mbps Wireless N
HotSpot Access Point
(TEW-636APB)
Workstation with 300Mbps
Wireless N PCI Adapter
(TEW-623PI)
Internet
Cable/DSL
Modem
300Mbps
10/100Mbps
Notebook with 300Mbps
Wireless N PC Card
(TEW-621PC)
4-Port Gigabit Firewall Router
(TWG-BRF114)
Workstation with 300Mbps
Wireless N USB Adapter
(TEW-624UB)
1
Français
2. Installation du matériel
Remarque : Déterminez un endroit idéal pour le Point d'accès. Le meilleur endroit se trouve généralement au centre de votre réseau sans fil. Veuillez brancher l'ordinateur en configurant le TEW-636APB au même switch/hub.
1.
Branchez un câble RJ-45 entre le
Switch/Hub et le port LAN du point d'accès.
2. Branchez le transformateur AC au
Access Point et ensuite à une prise de courant.
3. Vérifiez que les lumières Power et
WLAN du panneau sont allumées.
2
Français
3. Configuration du point d'accès
Remarque : Il est recommandé de configurer le point d'accès depuis un ordinateur câblé.
1. Ouvrez votre navigateur Internet , tapez http://SCXXXXXX dans la barre d'adresse et enfoncez la touche Enter. XXXXXX représente les 6 derniers chiffres de l'adresse
Mac. Vous trouverez cette dernière en dessous du routeur.
2. Saisissez le nom d'utilisateur et le mot de passe et cliquez sur OK.
Nom d'utilisateur :admin
Mot de passe :password
3. Cliquez sur System et ensuite sur
Basic Settings. Sélectionnez votre pays ou votre domaie dans le menu déroulant. Si vous désirez attribuer une adresse IP statique au TEW-636APB, cliquez sur Fixed
IP Address et saisissez une adresse IP, un masque de sous réseau, une passerelle et un DNS correspondants à vos paramètres réseau utilisés. Cliquez ensuite sur
Save.
3
Français
4.
Cliquez sur Sans fil et ensuite sur
Paramètres de base.
Sélectionnez le Mode sans fil
désiré, le Point d'accès pour le
mode de fonctionnement et cliquez
sur Enregistrer.
5. Cliquez sur PA virtuels.
Sélectionnez un PA virtuel, cliquez sur Activer et ensuite sur
Configurer.
Remarque: L'exemple ci-dessous concerne la sécurisation WPA-PSK. Si vos adaptateurs sans fil ne supportent pas le WPA-PSK, sélectionnez le WEP.
6. Saisissez un SSID, sélectionnez le
système de sécurisation désiré, saisissez la clé réseau, cliquez sur
Enregistrer et ensuite sur retour.
7.
Répétez les étapes 5 et 6 pour chaque PA virtuel suivant.
8. Cliquez sur Management et ensuite sur Admin Login.
4
Français
9. Si vous le désirez, saisissez un nouveau nom d'utilisateur, cochez
Change Admin Password
(Changer le mot de passe Admin), saisissez un nouveau mot de passe et cliquez sur Enregistrer.
Par défaut:
Nom d'utilisateur : admin
Mot de passe : password
10.
Cliquez sur Appliquer et ensuite
sur Redémarrer.
Remarque: Si vous passez cette
étape, les paramètres que vous
avez modifié ne sont PAS
enregistrés.
L'installation est maintenant complète.
Si vous désirez des informations détaillées sur la configuration et les paramètres avancés du TEW-636APB , veuillez consulter la rubrique
Dépannage, le guide de l'utilisateur sur CD-ROM ou le site Internet de
TRENDnet sur http://www.trendnet.com.
Enregistrez votre produit
Afin d’être sûr de recevoir le meilleur niveau de service clientèle et le meilleur support possibles, veuillez prendre le temps d’enregistrer votre produit en ligne sur: www.trendnet.com/register
Nous vous remercions d’avoir choisi Trendnet
5
Français
Troubleshooting
Q1: I typed http://SCXXXXXX in my Internet Browser's Address Bar, but an error message says “The page cannot be displayed.” How can I get into the TEW-
636APB's web configuration page?
A1: First, check your hardware settings again by following the instructions in section 2. Second, make sure the LAN and WLAN lights are lit. Third, verify the
Mac Address of the access point. Look at the bottom of the access point. Copy the last six digits of the Mac Address. Then open up your browser and type in http://SCXXXXXX (XXXXXX represents the last six digits of the Mac Address) and then Enter. Fourth, perform a factory reset. Take a pin or paperclip, press on the reset button for 15 seconds, and then let go.
Q2 : All the settings are correct, but I can not make a wireless connection to the
Access Point.
A2: First, double check that the WLAN light on the Access Point is lit. Second, power cycle the Access Point. Unplug the power to the Access Point. Wait 15 seconds, then plug the power back in. Third, contact the manufacturer of your wireless network adapter. Make sure the wireless network adapter is configured with the proper SSID. The default SSID of the Access Point is wireless 0. If you have enabled any encryption on the Access Point, make sure to configure the wireless network adapter with the same Pre-shared key. If you do not remember the encryption key, log on to the access point configuration page from a wired computer. Click Wireless -> Virtual AP. Click on the desired Virtual AP and then click Configure.
If you still encounter problems or have any questions regarding the TEW-636APB, please contact TRENDnet's Technical Support Department.
6
Certifications
This equipment has been tested and found to comply with FCC and CE Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received. Including interference that may cause undesired operation.
Waste electrical and electronic products must not be disposed of with household waste. Please recycle where facilities exist. Check with you Local
Authority or Retailer for recycling advice.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.
ADVERTENCIA
En todos nuestros equipos se mencionan claramente las caracteristicas del adaptador de alimentacón necesario para su funcionamiento. El uso de un adaptador distinto al mencionado puede producir daños fisicos y/o daños al equipo conectado. El adaptador de alimentación debe operar con voltaje y frecuencia de la energia electrica domiciliaria existente en el pais o zona de instalación.
Customer Support
Visit www.trendnet.com/support
Email: [email protected]
Europe .
.
.
.
Toll Free Telephone: +00800 60 76 76 67
English/Espanol - 24/7
Worldwide
Telephone: +(31) (0) 20 504 05 35
English/Espanol - 24/7
Product Warranty Registration
Please take a moment to register your product online.
Go to TRENDnet’s website at http://www.trendnet.com/register
20675 Manhattan Place
Torrance, CA 90501
USA
Copyright ©2008. All Rights Reserved. TRENDnet.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement