Keysight PNA-X N5245A Configuration manual

Keysight Technologies
PNA Family
Microwave Network Analyzers
Configuration Guide
2 | Keysight | PNA Family Microwave Network Analyzers - Configurations Guide
Table of Contents
PNA Family Network Analyzer Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Test set and power configuration options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Application options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Accessories, calibration options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
PNA-X Series test set and power configuration options. . . . . . . . . . . . . . . . . . . . . . . . . 8
PNA Series test set and power configuration options. . . . . . . . . . . . . . . . . . . . . . . . . 10
PNA-L Series test set and power configuration options. . . . . . . . . . . . . . . . . . . . . . . . 12
PNA Family Application Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Measurement applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Noise figure options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
PNA-X block diagrams with noise figure option . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Noise figure options summary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Pulse, antenna, mm-wave . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
PNA Family Network Analyzer Upgrade Kits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Frequency, test ports, test set and power configurations . . . . . . . . . . . . . . . . . . . . . . . 21
Application options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Upgrade paths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Material measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Signal integrity measurements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Multiport measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Millimeter-wave measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Measurement Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Cables and adapter sets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Calibration kits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
For devices with 1.0 mm connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
For devices with 1.85 mm connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
For devices with 2.4 mm connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
For devices with K (2.92 mm) connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
For devices with 3.5 mm, SMA, or 2.92 mm connectors. . . . . . . . . . . . . . . . . . . . . . . . 30
For devices with 3.5 mm or SMA connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
For devices with Type-N connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
For devices with 7 mm connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
For devices with waveguide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Verification kits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
General Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Spare drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Probe. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Power meters and sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Comb generators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Amplifiers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Couplers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Equipment rack accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Monitors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Interface cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
3 | Keysight | PNA Family Microwave Network Analyzers - Configurations Guide
This configuration guide describes standard configurations,
options, accessories, upgrade kits and compatible peripherals for
the PNA Family microwave network analyzers. This guide should
be used with the Keysight Technologies, Inc. PNA Family data
sheets for a complete description of these analyzers.
PNA-X Series
N5249A 10 MHz to 8.5 GHz
N5241A 10 MHz to 13.5 GHz
N5242A 10 MHz to 26.5 GHz
N5244A 10 MHz to 43.5 GHz
N5245A 10 MHz to 50 GHz
N5247A 10 MHz to 67 GHz
PNA Series
N5221A 10 MHz to 13.5 GHz
N5222A 10 MHz to 26.5 GHz
N5224A 10 MHz to 43.5 GHz
N5225A 10 MHz to 50 GHz
N5227A 10 MHz to 67 GHz
PNA-L Series
N5239A 300 kHz to 8.5 GHz
N5231A 300 kHz to 13.5 GHz
N5232A 300 kHz to 20 GHz
N5234A 10 MHz to 43.5 GHz
N5235A 10 MHz to 50 GHz
4 | Keysight | PNA Family Microwave Network Analyzers - Configurations Guide
Keysight offers the following options for all PNA Family network analyzers
Certification options
Documentation
Commercial calibration certification with test data (Option UK6)
Complete set of measurements which tests unit to manufacturer’s
published specifications. Includes calibration label, calibration
certificate, and data report. Conforms to ISO 9001.
The PNA Series instruments are equipped with an Online Help
system available within the instrument in English only. All PNA
documentation is available on the web:
www.keysight.com/find/pna
ISO 17025 compliant calibration (Option 1A7)
Calibration Software Licenses
Complete set of measurements which tests unit to manufacturer’s
published specifications. Includes calibration label, ISO 17025
calibration certificate, and data report, measurement uncertainties and guardbands on all customer specifications. Conforms to
ISO 17025 and ISO 9001.
ANSI Z540 compliant calibration (Option A6J)
Complete set of measurements which tests unit to manufacturer’s
published specifications. Includes pre- and post-adjustment
data with measurement uncertainty information compliant to the
ANSI/NCSL Z540 standard.
Warranty and service
3- and 5-year warranty and service plans are available at the time
of instrument purchase. Standard warranty is 3 years.
Perpetual license for built-in performance test
software for Keysight inclusive cal (Option 897)
Adds built-in performance testing and calibration software for
self-maintainers. Requires additional equipment. See the analyzer’s Service Guide for more information on equipment required.
Perpetual license for built-in performance
test software for Standards compliant cal
(Option 898)
Adds built-in performance testing and calibration software for
self-maintainers. Requires additional equipment. See the analyzer’s Service Guide for more information on equipment required.
5 | Keysight | PNA Family Microwave Network Analyzers - Configurations Guide
PNA Family Network Analyzer Configurations
PNA-X Series
PNA Series
N5249A 10 MHz to 8.5 GHz
N5241A 10 MHz to 13.5 GHz
N5242A 10 MHz to 26.5 GHz
N5244A 10 MHz to 43.5 GHz
N5245A 10 MHz to 50 GHz
N5247A 10 MHz to 67 GHz
PNA-L Series
N5221A 10 MHz to 13.5 GHz
N5222A 10 MHz to 26.5 GHz
N5224A 10 MHz to 43.5 GHz
N5225A 10 MHz to 50 GHz
N5227A 10 MHz to 67 GHz
N5239A 300 kHz to 8.5 GHz
N5231A 300 kHz to 13.5 GHz
N5232A 300 kHz to 20 GHz
N5234A 10 MHz to 43.5 GHz
N5235A 10 MHz to 50 GHz
Test set and power configuration options
Choose one test set and power configuration option. Option 2xx indicates two test ports. Option 4xx indicates four test ports. To add options to a product,
order the corresponding item number (N52xxA-xxx).
Configurable
Test Set
Description
Source
Receiver
Attenuators Attenuators Bias-tees
Internal
Second
Source
Internal
Combiner
Mechanical
Switches
Additional Information
PNA-X Series
Option 200
●
Option 200, H85, 285
●
●
●
Option 200, 219
●
●
●
Option 200, H85, 285, 2241
●
●
●
Option 200, 219, 224
●
●
●
1
Option 400
●
●
Option 400, H85, 485
●
●
●
Option 400, 419
●
●
●
●
●
●
●
●
●
Option 217
●
●
●
Option 219
Option 400
●
●
●
Option 401
●
1
Option 400, H85, 485, 423
Option 400, 419, 423
Not available on 67 GHz model
●
1
●
●
●
●
●
Requires Option 080
Not available on 67 GHz model
●
●
●
Requires Option 080
●
Option 080 recommended
●
Option 080 recommended
Not available on 67 GHz model
Option 080 recommended
●
●
●
●
Requires Option 080
Not available on 67 GHz model
●
●
●
Requires Option 080
PNA Series
Option 200
Option 201
●
2-port metrology option
Option 210
Not available on 67 GHz model
●
Option 410
Option 417
●
●
●
Option 419
●
●
●
●
●
●
●
●
●
Option 080 recommended
●
Option 080 recommended
●
4-port metrology option
●
Option 080 recommended
Not available on 67 GHz model
●
Option 080 recommended
PNA-L Series
Option 200
Option 216
Available on only N5231A/2A
Option 400
Option 416
2
Available on only N5231A/2A
1. Order special model N524xAS instead of N524xA. Order N524xA-xxx items for other standard options. Option H85 requires Option 285 or 485 which includes
the extended power range of Option 219 or 419; therefore these options cannot be combined.
2. Adds one source attenuator to be shared with all test ports.
6 | Keysight | PNA Family Microwave Network Analyzers - Configurations Guide
PNA Family Network Analyzer Configurations (continued)
PNA-X Series
PNA Series
N5249A 10 MHz to 8.5 GHz
N5241A 10 MHz to 13.5 GHz
N5242A 10 MHz to 26.5 GHz
N5244A 10 MHz to 43.5 GHz
N5245A 10 MHz to 50 GHz
N5247A 10 MHz to 67 GHz
PNA-L Series
N5221A 10 MHz to 13.5 GHz
N5222A 10 MHz to 26.5 GHz
N5224A 10 MHz to 43.5 GHz
N5225A 10 MHz to 50 GHz
N5227A 10 MHz to 67 GHz
N5239A 300 kHz to 8.5 GHz
N5231A 300 kHz to 13.5 GHz
N5232A 300 kHz to 20 GHz
N5234A 10 MHz to 43.5 GHz
N5235A 10 MHz to 50 GHz
Application options
To add options to a product, order the corresponding item number (N52xxA-xxx).
Measurement application
Automatic fixture removal
For PNA-L
Series
For PNA-X Series
For PNA Series
N524xA-007
N522xA-007
N523xA-007
Additional Information
Requires Windows 7 OS 8
Time-domain measurements
N524xA-010
N522xA-010
N523xA-010
Noise figure measurements using standard
receivers1
N524xA-028
N522xA-028
n/a
Requires Option 080. For measuring frequency converters,
requires Option 082 or 083. Not available with N522xA-200,
-210, -400 and -410
Fully-corrected noise figure
measurements1
N524xA-029
n/a
n/a
Requires Option 080 and for N5241/42/49A, one of Options 219,
224, 419, 423 or H85. For N5244/45/47A, requires Option 224
or 423. On N5247A, noise receivers work up to 50 GHz only. For
measuring frequency converters, requires Option 082 or 083.
Frequency offset 2
N524xA-080
N522xA-080
N523xA-080
Scalar-calibrated converter measurements3
N524xA-082
N522xA-082
N523xA-082
Requires Option 080
Vector- and scalar-calibrated converter
measurements 3, 4
N524xA-083
N522xA-083
n/a
Requires Option 080
Embedded LO measurements
N524xA-084
N522xA-084
n/a
Requires Option 082 or Option 083. Also works with Options
028, 029, 086 and 087
Gain compression application
N524xA-086
N522xA-086
n/a
For measuring frequency converters, requires Option 082 or 083
Intermodulation distortion
application5
N524xA-087
N522xA-087
n/a
Requires Option 080 For measuring frequency converters,
requires Option 082 or 083. Not available with N522xA-200,
-210, -400 and -410
Source phase control
N524xA-088
N522xA-088
n/a
Not available with N522xA-200 and -210
Differential and I/Q devices application
N524xA-089
N522xA-089
n/a
Requires Option 080 and 400, 401, 410, 417, or 419, and
Windows 7 OS 8
Spectrum analyzer
N524xA-090
N522xA-090
n/a
Requires Option 080, Windows 7 OS, and DSP version 5 8. Test
set and power configuration option with receiver attenuators is
recommended.
Integrated true-mode stimulus application
N524xA-460
N522xA-460
n/a
Requires one of Options 400, 401, 410, 417, 419 or 423
N-port capabilities
N524xA-551
N522xA-551
N523xA-551
Not available with N522xA-200, -210, -400 and -410, and
N523xA-200 and -400
6
7
1. For N522xA and N5241/42/49A, vector-noise-corrected measurements require an ECal for use as an impedance tuner. For N5244/45/47A with Option 029,
an internal tuner is included. For calibration, Option 028 requires a power meter, and Option 029 requires either a power meter or a 346-series noise source
(Keysight 346C or 346C-K01 recommended). All options require a power meter for measuring mixers and converters.
2. Option 080 is required to configure an external source using External Device Configuration dialog.
3. Option 082 is a subset of Option 083; therefore, they cannot be ordered together.
4. A configurable test set is required for VMC measurements (to connect a reference mixer) or for SMC+Phase measurements using the comb-generator-based
calibration. When ordered with N522xA-200, -210, -400 and -410, Option 083 adds phase and delay measurements only by using SMC+Phase with a
calibration mixer.
5. Option 087 can be ordered without N524xA-224 or N524xA-423, but may require external equipment such as a signal generator and a combiner. Refer to
page 13 for more details.
6. When ordering a test set, select an appropriate interface kit. Refer to page 22 Multiport Measurements section for more details.
7. When configuring N524xA as a multiport analyzer using Option 551 and a multiport test set, the combiner feature of Option 224 or 423 is temporarily
disabled. When configuring N524xA as a standalone analyzer, the combiner feature is enabled.
8. The Windows 7 upgrade kit is model N8983A. This upgrade kit contains a new disk drive and requires an i7 or Celeron CPU. For units with older CPUs, order
Option PC6 for a new i7 CPU. For adding Option 090 to units with an older CPU, order Options PC6 and SP5.
7 | Keysight | PNA Family Microwave Network Analyzers - Configurations Guide
PNA Family Network Analyzer Configurations (continued)
PNA-X Series
PNA Series
N5249A 10 MHz to 8.5 GHz
N5241A 10 MHz to 13.5 GHz
N5242A 10 MHz to 26.5 GHz
N5244A 10 MHz to 43.5 GHz
N5245A 10 MHz to 50 GHz
N5247A 10 MHz to 67 GHz
PNA-L Series
N5221A 10 MHz to 13.5 GHz
N5222A 10 MHz to 26.5 GHz
N5224A 10 MHz to 43.5 GHz
N5225A 10 MHz to 50 GHz
N5227A 10 MHz to 67 GHz
N5239A 300 kHz to 8.5 GHz
N5231A 300 kHz to 13.5 GHz
N5232A 300 kHz to 20 GHz
N5234A 10 MHz to 43.5 GHz
N5235A 10 MHz to 50 GHz
Application options (continued)
To add options to a product, order the corresponding item number (N52xxA-xxx).
Description
For PNA-X Series
For PNA Series
For PNA-L Series
Additional Information
Pulsed-RF measurements
N524xA-008
N522xA-008
n/a
Requires Option 025
Add IF inputs
N524xA-020
N522xA-020
n/a
Pulse, antenna, mm-wave
Add pulse modulator to internal 1st source
N524xA-021
N522xA-021
n/a
Add pulse modulator to internal 2nd source
N524xA-022
N522xA-022
n/a
Add four internal pulse generators
N524xA-025
N522xA-025
n/a
Fast CW sweep
N524xA-118
N522xA-118
n/a
Requires one of Option 224, 400, 401, 417, 419, or 423
Nonlinear vector network analysis
1
Nonlinear component
characterization
N524xA-510
n/a
n/a
Requires Options 419 and 080, or 400, H85 and 080
Nonlinear X-parameters2
N524xA-514
n/a
n/a
Requires Options 423 and 510, requires MXG or PSG except
10 MHz tone-spacing
Nonlinear pulse envelope domain
N524xA-518
n/a
n/a
Requires Options 021, 025 and 510
Arbitrary load-inpedance
X-parameters
N524xA-520
n/a
n/a
Requires Option 514, requires MXG or PSG except 10
MHz tone-spacing
Accessories, calibration options
To add options to a product, order the corresponding item number (N52xxA-xxx).
Description
For PNA-X Series
For PNA Series
For PNA-L Series
Additional Information
Accessories
Rack mount kit for use without handles
N524xA-1CM
N522xA-1CM
N523xA-1CM
Rack mount kit for use with handles
N524xA-1CP
N522xA-1CP
N523xA-1CP
N1966A
N1966A
n/a
Perpetual license for built-in performance test
software for Keysight inclusive calibration3
N524xA-897
N522xA-897
N523xA-897
Perpetual license for built-in performance test
software for standard compliant calibration3
N524xA-898
N522xA-898
N523xA-898
Pulse I/O adapter
Calibration software
Calibration documentation
ISO 17025 compliant calibration
N524xA-1A7
N522xA-1A7
N523xA-1A7
Commercial calibration certificate with test data
N524xA-UK6
N522xA-UK6
N523xA-UK6
ANSI Z540 compliant calibration
N524xA-A6J
N522xA-A6J
N523xA-A6J
1. To configure NVNA, requires two comb generators with power supplies, Keysight calibration kits (mechanical or ECal), power meter and sensor or USB power sensor. Requires EXG,
MXG or PSG for X-parameter extraction (PNA-X 10 MHz reference output can be used for 10 MHz tone-spacing applications).
2. X-parameters is a trademark of Keysight Technologies.
3. Additional hardware required. Please refer to the analyzer’s Service Guide for required service test equipment.
8 | Keysight | PNA Family Microwave Network Analyzers - Configurations Guide
PNA-X Series test set and power configuration options1
The PNA-X is an integrated vector network analyzer featuring
a built-in S-parameter test set, one or two synthesized sources
used for device stimulus, a solid-state drive, USB interfaces,
and a 10.4” LCD touch screen display. The N5241A, N5242A, and
N5249A have 50 ohm, ruggedized 3.5 mm (m) test ports. The
N5244A and the N5245A have 50 ohm, ruggedized 2.4 mm (m)
test ports. The N5247A has 50 ohm, ruggedized 1.85 mm (m) test
ports. Included with each instrument is a mouse, keyboard (U.S.
style), a 3-year return-to-Keysight service warranty, and one day
of on-site productivity assistance (PS-S20-PNA).
Extended power range and bias-tees (Option 219)
Adds to the standard test set one 65 dB for N5241/42/49A,
60 dB for N5244/45A, and 50 dB for N5247A source attenuator
(set table in 5 dB increments for N5241/42/49A and 10 dB increments for N5244/45/47A), one 35 dB receiver attenuator (settable
in 5 dB increments) for N5241/42/44/45/49A and 50 dB receiver
attenuator (settable in 10 dB increments) for N5247A, and one
bias-tee to each test port. Option 219 requires Option 200.
IF inputs
rear panel
A test set and power configuration option is mandatory, choose
one of the following:
2-port standard test set and power range
(Option 200)
The standard 2-port test set comes with six front-panel access
loops. The loops provide access to the signal path between (a)
the source output and the reference receiver, (b) the source
output and directional coupler thru arm and (c) the coupled arm
of the directional coupler and the port receiver. The standard
test set also includes a solid-state internal RF transfer switch in
the R1 reference-receiver path.
R
Source 1
OUT 1
A
B
C
D
OUT 2
Pulse
modulator
Pulse generators
R1
R2
LO
A
B
To receivers
35 dB
65 dB
65 dB
Test port 1
35
dB
Test port 2
Add an internal second source, a combiner
and mechanical switches to 2-port analyzer
(Option 224)
IF inputs
rear panel
R
Source 1
OUT 1
A
B
C
D
OUT 2
Pulse
modulator
Pulse generators
R1
R2
LO
A
B
To receivers
Test port 1
Test port 2
High-power configurable and extended power
range (N524xAS Option H85/285)
With extended power range and bias-tees (Option 219), the
internal bias-tees limit the maximum test port input power to
+30 dBm. The N524xAS Option H85/285 removes the bias-tees
between the source attenuators and the test port couplers. This
extends the maximum port power that the analyzer can safely
handle to +43 dBm. Selecting OptionH85/285 adds internal
attenuators and cables. The N524xAS Option H85/285 and
Option 219 can not be ordered together. Option H85/285 is not
available for the N5247A. When ordering, select N524xAS then
add items N524xAS-H85, N524xAS-285 and N524xA-200.
Available with 2-port model only, this option adds an internal
second source, a combiner and mechanical switches. The internal second source provides an additional signal (fixed or swept)
for two-tone third-order-intercept (TOI) and intermodulation
testing of amplifiers, or it can be used as a fast swept-LO signal
for fixed-IF testing of mixers and converters. The mechanical
switches provide increased flexibility by having rear panel access
(front panel access for N5247A Source 1 and 2 Out 1) to signal
paths for advanced applications. Access to the second source
is available through two output connectors on the front panel.
Requires Options 200, 219 and 080.
rear panel
IF inputs
J11
J10
J9
J8
J7
J6
J5
RF
OUT
LO
OUT
J2
R
LO
Source 2
OUT 1
Source 1
OUT 1
OUT 2
To receivers
Pulse
modulator
OUT 2
J1
A B R1 R2
Pulse
modulator
R1
R2
Pulse generators
A
B
1
2
3
4
35 dB
65 dB
Test port 1
65 dB
Source 2
Output 1
Source 2
Output 2
35 dB
Test port 2
IF inputs
rear panel
R
Source 1
OUT 1
A
B
C
D
OUT 2
Pulse
modulator
Pulse generators
R1
35 dB
Test port 1
R2
LO
A
65 dB
1. The block diagrams shown above include hardware that must be ordered
as separate options, such as pulse generators (Option 025), pulse modulators (Options 021 and 022), and IF access (Option 020). In addition, the
combiner type and attenuator values vary by model number. Refer to the
product data sheet for the correct block diagram for a specific model.
To receivers
B
65 dB
Test port 2
35 dB
9 | Keysight | PNA Family Microwave Network Analyzers - Configurations Guide
PNA-X Series test set and power configuration options1 (continued)
4-port
standard test set, power range and an
internal second source (Option 400)
Extended power range and bias-tees
(Option 419)
The standard 4-port test set comes with 12 front-panel access
loops and a built-in second source. The loops provide access to
the signal path between (a) the source output and the reference
receiver, (b) the source output and directional coupler thru arm
and (c) the coupled arm of the directional coupler and the port
receiver. The internal second source provides an additional signal
(fixed or swept) for two-tone third-order-intercept (TOI) and
intermodulation testing of amplifiers, or it can be used as a fast
swept-LO signal for fixed-IF testing of mixers and converters.
With two sources, source 1 is accessible through test ports 1
and 2, and source 2 is accessible through test ports 3 and 4.
The standard test set also includes a solid-state internal RF
transfer switch in the R1 reference-receiver path. Option 080 is
recommended.
Adds to the standard test set one 65 dB for N5241/42/49A, 60 dB
for N5244/45A, and 50 dB for N5247A source attenuator (settable in 5 dB increments for N5241/42/49A and 10 dB increments
for N5244/45/47A), one 35 dB receiver attenuator (settable in
5 dB increments) for N5241/42/44/45/49A and 50 dB receiver
attenuator (settable in 10 dB increments) for N5247A, and one
bias-tee to each test port. Option 419 requires Option 400.
IF inputs
rear panel
OUT 1
A B C
D
Pulse generators
Source 2
OUT 1
OUT 2
Pulse
modulator
To receivers
R3
R1
R4
R2
C
35 dB
D
35 dB
65 dB
R
Source 1
C
OUT 2
LO
IF inputs
OUT 1
A B
Pulse
modulator
A
rear panel
R
Source 1
B
35 dB
65 dB
65 dB
65 dB
35 dB
D
OUT 2
Test port 1
Test port 3
Test port 4
Test port 2
Pulse
modulator
LO
Pulse generators
Source 2
OUT 1
OUT 2
Pulse
modulator
To receivers
R3
R1
R4
A
R2
C
Test port 1
D
Test port 3
B
Test port 4
Test port 2
High-power configurable and extended power
range (N524xAS Option H85/485)
With extended power range and bias-tees (Option 419), the
internal bias-tees limit the maximum test port input power to
+30 dBm. The N524xAS Option H85/485 removes the bias-tees
between the source attenuators and the test port couplers. This
extends the maximum port power that the analyzer can safely
handle to +43 dBm. Selecting Option H85/485 adds internal attenuators and cables. The N524xAS Option H85/485 and Option
419 can not be ordered together. Option H85/485 is not available
for the N5247A. When ordering, select N524xAS then add items
N524xAS-H85, N524xAS-485 and N524xA-400.
Add an internal combiner and mechanical
switches to 4-port analyzer (Option 423)
Available with 4-port model only, this option adds a combiner
and mechanical switches. The mechanical switches provide
increased flexibility by having rear panel access (front panel
access for the N5247A Source 1 and 2 Out 1) to signal paths for
advanced applications. Requires Options 400, 419 and 080.
rear panel
IF inputs
J11
J10
J9
J8
J7
J6
J5
RF
OUT
LO
OUT
J4
OUT 1
OUT 1
OUT 2
A
B
C
J1
D
LO
OUT 2
Pulse generators
Pulse
modulator
Pulse
modulator
J2
R
Source 2
(standard)
Source 1
J3
1
To receivers
2
3
4
R1
R3
A
65 dB
Test port 1
35 dB
R4
C
65 dB
Test port 3
35 dB
R2
D
65 dB
Test port 4
35 dB
B
65 dB
35 dB
Test port 2
IF inputs
rear panel
R
Source 1
OUT 1
A
B
C
D
OUT 2
Pulse
modulator
LO
Pulse generators
Source 2
OUT 1
OUT 2
Pulse
modulator
To receivers
R3
R1
R4
A
35 dB
65 dB
Test port 1
R2
C
D
35 dB
65 dB
Test port 3
B
35 dB
65 dB
Test port 4
65 dB
Test port 2
35 dB
1. The block diagrams shown above include hardware that must be ordered
as separate options, such as pulse generators (Option 025), pulse modulators (Options 021 and 022), and IF access (Option 020). In addition, the
combiner type and attenuator values vary by model number. Refer to the
product data sheet for the correct block diagram for a specific model.
10 | Keysight | PNA Family Microwave Network Analyzers - Configurations Guide
PNA Series test set and power configuration options1
The PNA is an integrated vector network analyzer featuring a
built-in S-parameter test set, one or two synthesized sources
used for device stimulus, a solid-state drive, USB interfaces, and
a 10.4” LCD touch screen display. The N5221A and the N5222A
have 50 ohm, ruggedized 3.5 mm (m) test ports. The N5224A
and the N5225A have 50 ohm, ruggedized 2.4 mm (m) test ports.
The N5227A has a 50 ohm, ruggedized 1.85 mm (m) test ports.
Included with each instrument is a mouse, keyboard (U.S. style),
a 3-year return-to-Keysight service warranty, and one day of
on-site productivity assistance (PS-S20-PNA).
A test set and power configuration option is mandatory, choose
one of the following:
2-ports, single source, with extended power range
(Option 217)
The 2-port test set with extended power range comes with a
configurable test set, source and receiver attenuators at each
port. For N5221/22A, the source attenuators are 65 dB in 5 dB
steps and the receiver attenuators are 35 dB in 5 dB steps. For
N5224/25A, the source attenuators are 60 dB in 10 dB steps and
the receiver attenuators are 35 dB in 5 dB steps. Also included
is a solid-state internal RF transfer switch in the R1 referencereceiver path. This configuration is not available on N5227A.
IF inputs
rear panel
Source
OUT 1
2-ports, single source, base configuration (Option
200/210)
R
A
B
C
D
OUT 2
Pulse
modulator
Pulse generators
R1
The 2-port with base configuration has no front-panel access
loops.
R2
LO
A
35 dB
65 dB
B
To receivers
35 dB
65 dB
IF inputs
rear panel
Source
OUT 1
R
A
B
C
D
OUT 2
2-ports, single source, with extended power range
and bias-tee (Option 219)
Pulse
modulator
Pulse generators
R1
R2
LO
A
B
To receivers
Test port 1
Test port 2
2-ports, single source, with configurable test set
(Option 201)
The 2-port configurable test set comes with six front-panel access loops. The loops provide access to the signal path between
(a) the source output and the reference receiver, (b) the source
output and directional coupler thru arm and (c) the coupled arm
of the directional coupler and the port receiver at all ports. Also
included is a solid-state internal RF transfer switch in the R1
reference-receiver path.
The 2-port test set with extended power range and bias-tee
comes with a configurable test set, source and receiver attenuators, and bias-tee at each port. For N5221/22A, the source
attenuators are 65 dB in 5 dB steps and the receiver attenuators
are 35 dB in 5 dB steps. For N5224/25A, the source attenuators
are 60 dB in 10 dB steps and the receiver attenuators are 35 dB
in 5 dB steps. For N5227A, both source and receiver attenuators
are 50 dB in 10 dB steps. Also included is a solid-state internal
RF transfer switch in the R1 reference-receiver path.
IF inputs
rear panel
Source
OUT 1
Source
OUT 1
R
A
B
C
Pulse generators
65 dB
Test port 1
Pulse generators
R1
A
D
To receivers
B
35 dB
65 dB
Test port 2
R2
LO
B
To receivers
Test port 1
C
R2
LO
35 dB
D
Pulse
modulator
B
OUT 2
R1
A
OUT 2
A
Pulse
modulator
IF inputs
rear panel
R
Test port 2
1. The block diagrams shown above include hardware that must be ordered
as separate options, such as pulse generators (Option 025), pulse modulators (Options 021 and 022), and IF access (Option 020). In addition, the
attenuator values vary by model number. Refer to the product data sheet
for the correct block diagram for a specific model.
11 | Keysight | PNA Family Microwave Network Analyzers - Configurations Guide
PNA Series test set and power configuration options1 (continued)
4-ports, dual source, base configuration
(Option 400/410)
4-ports, dual source, with extended power range
(Option 417)
The 4-port with base configuration has no front-panel access
loops.
The 4-port test set with extended power range comes with
two internal sources, configurable test set, source and receiver
attenuators at each port. For N5221/22A, the source attenuators
are 65 dB in 5 dB steps and the receiver attenuators are 35 dB in
5 dB steps. For N5224/25A, the source attenuators are 60 dB in
10 dB steps and the receiver attenuators are 35 dB in 5 dB steps.
Also included is a solid-state internal RF transfer switch in the
R1 reference-receiver path. This configuration is not available on
N5227A.
IF inputs
rear panel
R
Source 1
OUT 1
A
B
C
D
OUT 2
Pulse
modulator
LO
Pulse generators
Source 2
OUT 1
OUT 2
Pulse
modulator
To receivers
R3
R1
R4
A
R2
C
D
B
IF inputs
rear panel
R
Source 1
OUT 1
Test port 1
Test port 3
Test port 4
Test port 2
A
B
C
D
OUT 2
Pulse
modulator
LO
Pulse generators
Source 2
OUT 1
Pulse
modulator
To receivers
4-ports, dual source, with configurable test set
(Option 401)
OUT 2
R3
R1
R4
A
35 dB
The 4-port configurable test set comes with two internal sources,
twelve front-panel access loops. The loops provide access to
the signal path between (a) the source output and the reference
receiver, (b) the source output and directional coupler thru arm
and (c) the coupled arm of the directional coupler and the port
receiver at all ports. Also included is a solid-state internal RF
transfer switch in the R1 reference-receiver path.
IF inputs
rear panel
R
Source 1
OUT 1
A
B
C
D
OUT 2
Pulse
modulator
LO
Pulse generators
Source 2
OUT 1
OUT 2
Pulse
modulator
To receivers
R3
R1
R4
A
Test port 1
R2
C
Test port 3
D
Test port 4
B
R2
C
D
35 dB
65 dB
Test port 1
B
35 dB
65 dB
65 dB
65 dB
Test port 3
Test port 4
35
dB
Test port 2
4-ports dual source, with extended power range
and bias-tee (Option 419)
The 4-port test set with extended power range and bias-tee
comes with two internal sources, configurable test set, source
and receiver attenuators, and bias-tee at each port. For
N5221/22A, the source attenuators are 65 dB in 5 dB steps and
the receiver attenuators are 35 dB in 5 dB steps. For N5224/25A,
the source attenuators are 60 dB in 10 dB steps and the receiver
attenuators are 35 dB in 5 dB steps. For N5227A, both source
and receiver attenuators are 50 dB in 10 dB steps. Also included
is a solid-state internal RF transfer switch in the R1 referencereceiver path.
Test port 2
IF inputs
rear panel
R
Source 1
OUT 1
A
B
C
D
OUT 2
Pulse
modulator
LO
Pulse generators
Source 2
OUT 1
OUT 2
Pulse
modulator
To receivers
R3
R1
R4
A
35 dB
65 dB
Test port 1
R2
C
D
35 dB
65 dB
Test port 3
B
35 dB
65 dB
Test port 4
65 dB
35
dB
Test port 2
1. The block diagrams shown above include hardware that must be ordered
as separate options, such as pulse generators (Option 025), pulse modulators (Options 021 and 022), and IF access (Option 020). In addition, the
attenuator values vary by model number. Refer to the product data sheet
for the correct block diagram for a specific model.
12 | Keysight | PNA Family Microwave Network Analyzers - Configurations Guide
PNA-L Series test set and power configuration options
The PNA-L is an integrated vector network analyzer featuring a
built-in S-parameter test set, one synthesized source used for
device stimulus, a solid state drive, USB interfaces, and a 10.4”
LCD touch screen display. The N5239A, N5231A and the N5232A
have 50 ohm, ruggedized 3.5 mm (m) test ports. The N5234A
and N5235A have 50 ohm, ruggedized 2.4 mm (m) test ports.
Included with each instrument is a mouse, keyboard (U.S. style),
and a 3-year return-to-Keysight service warranty. For one day
of on-site productivity assistance (not included with instrument
purchase), request quantity 1 each PS-S20-PNA.
A test set and power configuration option is mandatory, choose
one of the following:
4 ports, single source, base configuration (Option
400)
The 4-port base configuration has no front-panel loops, and is
available only on the N5231A and N5232A.
Source
To receivers
R
A
2 ports, single source, base configuration (Option
200)
The 2-port with base configuration has no front-panel access
loops.
LO
Source
To receivers
R1
R2
A
B
Test port 1
Test port 2
2 ports, single source, with configurable test set
and source attenuators (Option 216)
The 2-port test set comes with a configurable test set and
source attenuator at each port. The configurable test set adds six
front-panel access loops. The loops provide access to the signal
path between (a) the source output and the reference receiver,
(b) the source output and directional coupler thru arm, and (c) the
coupled arm of the directional coupler and the port receiver at all
ports. The source attenuators are 60 dB in 10 dB steps.
Test port 1
Source
To receivers
60 dB
60 dB
R1
R2
A
Test port 1
B
Test port 2
B
Test port 2
C
Test port 3
D
Test port 4
4 ports, single source, with configurable test set
and source attenuator (Option 416)
The 4-port test set comes with a configurable test set and one
source attenuator to be shared with all ports. The configurable
test set adds nine front-panel access loops. The loops provide
access to the signal path between (a) the source output and the
reference receiver, (b) the source output and directional coupler
thru arm at all ports, and (c) the coupled arm of the directional
coupler and the port receiver at all ports. The source attenuator
is 60 dB in 10 dB steps. This configuration is available on only
N5231A and N5232A.
Source
LO
60 dB
To receivers
R
A
Test port 1
LO
LO
B
Test port 2
C
Test port 3
D
Test port 4
13 | Keysight | PNA Family Microwave Network Analyzers - Configurations Guide
PNA Family Application Options
Measurement applications
Solid black series name indicates the feature is available on that
series, while gray series name with strikethrough indicates the
feature is not available on that series. For example;
PNA: Available on PNA Series
PNA: Not available on PNA Series
Automatic fixture removal (Option 007)
PNA-X PNA PNA-L
Many devices do not have coaxial connectors and are put in fixtures
in order to measure them in a coaxial environment. Accurately removing the effects of the fixture is required to get a good measurement of the device under test (DUT). This option adds a powerful
application wizard to guide you through characterizing a fixture and
removing it from the measurement. Devices can be single ended or
differential. Files can be saved in a variety of formats for later use in
PNA, ADS, and PLTS. Requires Windows 7 OS.
Time domain (Option 010)
PNA-X PNA PNA-L
This option enables the analyzer to view reflection and transmission responses in time or distance. Use time domain to tune filters,
gate out the response of fixtures and cables, characterize the
impedance of transmission lines and more. If eye-diagram analysis, W-element modeling or high-speed interconnect testing is
required, PLTS N1930B software must be used.
Frequency offset (Option 080)
PNA-X PNA PNA-L
This option enables the analyzer to set the source frequency
independently from where the receivers are tuned, and is
required to configure an external source using External Device
Configuration. This ability is important for measuring amplifiers,
mixers, and frequency converters.
1. When a comb generator is used as a phase reference for calibration and
the start frequency of the measurement is less than 55 MHz, a usersupplied calibration mixer is required. For measurements between
50 GHz and 67 GHz, an additional high-pass filter is required (two backto-back Keysight V281A waveguide-to-coax adapters recommended;
must be ordered separately).
Scalar-calibrated converter measurements (Option 082)
PNA-X PNA PNA-L
With a simple setup and calibration, this application delivers
the highest accuracy for scalar conversion-loss/gain measurements by combining one-port and power-meter calibrations to
remove mismatch errors. Option 082 provides an intuitive and
easy-to-use user interface for setting up mixer and converter
measurements, with single or dual conversion stages. It can
control the analyzer’s built-in source(s) as well as external signal
generators for use as LO signals. Supported external sources
include the Keysight ESG, PSG, and MXG Series, as well as other
SCPI-controlled signal generators. Option 082 requires Option
080, and cannot be ordered with Option 083. It is compatible
with Option 084, which enables measurements of converters with
internal LOs.
Vector- and scalar-calibrated converter
measurements (Option 083)
PNA-X PNA PNA-L
This application includes the scalar mixer/converter plus phase
(SMC+Phase) measurement class that provides fully calibrated
conversion gain/loss, relative phase, and absolute group delay
measurements of mixers and converters without the need for
reference or calibration mixers. Eliminating the calibration mixer
requires a U9391C/F/G comb generator and an external DC
power supply capable of sourcing +15 V to 300 mA for U9391C/F
or 800 mA for U9391G1. A vector mixer/converter measurement
(VMC) class is also included for measuring the phase difference
between multiple paths or devices, or for measuring phase
shifts within a device. Using VMC or the comb-generator-based
calibration for SMC+Phase requires an instrument with a configurable test set (i.e., has front-panel RF loops). For units without
front-panel loops, SMC+Phase can be used with a calibration
mixer supplied by the user. Option 083 provides an intuitive and
easy-to-use user interface for setting up mixer and converter
measurements, with single or dual conversion stages. It can
control the analyzer’s built-in source(s) as well as external signal
generators for use as LO signals. Supported external sources
include the Keysight ESG, PSG, and MXG Series, as well as other
SCPI-controlled signal generators. Option 083 requires Option
080, and cannot be ordered with Option 082. It is compatible
with Option 084, which enables measurements of converters with
internal LOs.
14 | Keysight | PNA Family Microwave Network Analyzers - Configurations Guide
Embedded LO measurements (Option 084)
PNA-X PNA PNA-L
This option tunes the analyzer’s receivers to the output frequency
of the converter under test without the need for access to internal
LOs or a common reference signal. For converters with embedded
LOs, this option requires Option 082 (enables match-corrected
conversion loss/gain measurements) or Option 083 (enable absolute
group delay measurements). This option also works with Option
086 gain compression application, Option 087 intermodulation
distortion application, and Option 028/029/H29 noise figure
applications.
Gain compression application (Option 086)
PNA-X PNA PNA-L
The gain compression application (GCA) provides input power,
output power, gain, and phase at the compression point of an
amplifier or frequency converter, over a specified frequency
range. GCA's SMART Sweep is very fast and easy-to-use. GCA
also includes a guided calibration that corrects for absolute
power levels, frequency response, and mismatch errors.
Intermodulation distortion application
(Option 087) PNA-X PNA PNA-L
The intermodulation distortion (IMD) application makes it very
easy to set up and calibrate swept-IMD measurements of both
amplifiers and frequency converters. It controls the frequency and
power of internal and external sources and tunes the receivers to
the main tones as well as the IMD products in a single measurement channel. The user can sweep either the center frequency
of the two stimulus signals, the frequency spacing of the two
stimulus signals about a fixed center frequency, or the power of
one or both stimulus signals or the power of the LO signal. The
analyzer can measure intermodulation distortion products of
order 2, 3, 5, 7, or 9, and can display the associated intercept
points. In addition, an IM Spectrum mode gives a spectrumanalyzer-like display for confirming or trouble-shooting measurements. Requires Option 080. Not available with PNA Options 200,
210, 400 and 410. When configured with a 2-port PNA or 2-port
PNA-X with either Option 200 or 219, an external signal generator
and a combiner are required. When configured with a 4-port PNA
or 4-port PNA-X with Option 400 or 419, the two internal sources
and an unused test port coupler configured as a combiner can
be used for two-tone IMD measurements. When configured with
PNA-X Option 224 or 423, the two internal sources and internal
combiner can be used for two-tone IMD measurements.
Source phase control (Option 088)
PNA-X PNA PNA-L
This option allows users to set calibrated, arbitrary phase
differences between two signal sources. The sources can be the
analyzer’s internal sources or external signal generators routed
through the analyzer’s test set. The phase difference can be
fixed, or swept between two specified phase values. Option 088
also controls the relative power level between the sources using
the receiver-leveling feature. Option 088 is targeted for activeload control, where the analyzer provides a precise, electronically
settable impedance to the output port of a device, while gain and
output power are measured. This capability can be combined
with external load-pull software to create traditional load-pull
power contours. Not available with PNA Options 200 and 210.
Differential and I/Q devices application (Option 089)
PNA-X PNA PNA-L
This option combines source-phase control of multiple internal or
external sources with frequency-offset mode, enabling simplified
test of I/Q modulators/converters and differential mixers, and
harmonic measurements of differential amplifiers. The phase
difference between sources can be fixed (for example, at 90 or
180 degrees), or swept between two specified phase values.
Providing accurate control of the relative phase between sources
eliminates the need for hybrid couplers and baluns to create
quadrature or differential signals. After achieving the desired
phase alignment, the instrument’s receivers can be tuned to all
frequencies needed to characterize the DUT. On an I/Q modulator
for example, measurements can be made of both the desired
and suppressed conversion bands, along with LO leakage,
harmonics and other spurious signals. Phase sweeps can be used
to determine a DUT’s phase imbalance versus frequency. Users
can specify measurements with individual receivers or multiple
receivers combined with a wide range of mathematical operators.
Power measurements can employ match correction for increased
accuracy. Option 089 only works on 4-port PNA or PNA-X
models, and requires Option 080 and Windows 7 OS.
15 | Keysight | PNA Family Microwave Network Analyzers - Configurations Guide
PNA Family Application Options (continued)
Measurement applications (continued)
Solid black series name indicates the feature is available
on that series, while gray series name with strikethrough indicates
the feature is not available on that series. For example;
PNA:
Available on PNA Series
PNA: Not available on PNA Series
Spectrum analyzer (Option 090)
PNA-X PNA PNA-L
The spectrum analyzer (SA) option adds high-performance
microwave spectrum analysis to the PNA and PNA-X Series. With
fast stepped-FFT sweeps due to optimized data processing, the
SA option provides quick spurious searches over broad frequency
ranges. Option 090 enables spectrum measurements with the test
receiver at each test port, and a reference receiver (two reference
receivers for 2-port configuration) simultaneously. This multichannel SA used with the internal swept-signal generators allows
efficient spurious analysis of mixers and converters. The SA option
employs source power and receiver response calibration as well
as fixture de-embedding, providing in-fixture or on-wafer spectrum measurements with the highest level of accuracy. Requires
Option 080, Windows 7 OS, and DSP version 5. It is recommended
to use this option on instruments with receiver attenuators to
avoid receiver compression when measuring large signals.
Integrated true-mode stimulus application
(Option 460) PNA-X PNA PNA-L
Integrated true-mode stimulus application (iTMSA) provides
mis-match-corrected true-mode (true differential mode and true
common mode) stimulus and enables accurate balanced measurements under real operating conditions. iTMSA also provides
balanced measurements with forward-only sweep, reverse-only
sweep, and frequency or power sweep with arbitrary phase and
amplitude off-sets. Requires one of Options 400, 401, 410, 417,
419 and 423.
1. When configuring N524xA as a multiport analyzer using Option 551 and a multiport test set, the combiner feature of Option 224 or 423 is temporarily disabled. When configured as a standalone analyzer, the combiner
feature is enabled. When ordering a test set, select an appropriate
interface kit. Refer to page 22 Multiport Measurements section for more
details.
2. Only N4690 Series ECal modules are supported for use as an impedance
tuner.
N-port capabilities (Option 551)1
PNA-X PNA PNA-L
Adds a multiport analyzer mode, which enables full N-port error
correction and measurement capabilities using an external test
set. Only standard measurement class is available in the multiport analyzer mode. Not available with PNA Options 200, 210,
400 and 410. For multiport analysis greater than 8 ports, it is
highly recommended to use PLTS software N1930B to manage
the large data format files that easily grow exponentially (12 port
S-parameter files have 144 S-parameter elements).
Noise figure options
Noise figure measurements using standard receivers (Option 028) PNA-X PNA PNA-L
This option adds firmware for high-accuracy noise figure measurements of amplifiers, frequency converters, and mixers using
the analyzer’s standard receivers, and utilizing Keysight’s unique
source-correction technique. Using an Keysight ECal module
configured as an impedance tuner (N4691B/93A/94A-M0F
recommended; must be ordered or supplied separately 2), the
effects of imperfect system-source match are removed, greatly
improving the accuracy of the cold-source technique. This approach surpasses the accuracy provided by the Y-factor method
and other cold-source implementations. A scalar calibration
choice is also available that offers less accuracy but is faster and
does not require the external ECal module used as an impedance
tuner. For calibration, a power meter and separate ECal module
or mechanical calibration kit is required (must be ordered or
supplied separately). An external preamplifier and filter(s) is
required for devices with < 30 dB of excess noise (gain plus noise
figure in dB) up to 20 GHz, < 40 dB up to 50 GHz, or < 45 dB up to
67 GHz. Front panel jumpers provide a convenient spot for adding
a preamplifier and filter for low gain, low noise figure devices. Not
available with N522xA-200 and -400.
16 | Keysight | PNA Family Microwave Network Analyzers - Configurations Guide
PNA Family Application Options (continued)
Noise figure options
Solid black series name indicates the feature is available
on that series, while gray series name with strikethrough
indicates the feature is not available on that series. For
example:
PNA:
PNA:
Available on PNA Series
Not available on PNA Series
Fully-corrected noise figure measurements
(Option 029) PNA-X PNA PNA-L
This option adds a low-noise receiver and firmware to the
PNA-X1 for high-accuracy noise figure measurements of
amplifiers, frequency converters, and mixers, utilizing Keysight’s
unique source-correction technique. Using an Keysight ECal
module configured as an impedance tuner for N5241/42/49A (3.5
mm N4691B-M0F recommended; must be ordered or supplied
separately 2), or a built-in tuner for N5244/45/47A, the effects of
imperfect system-source match are removed, greatly improving
the accuracy of the cold-source technique. This approach
surpasses the accuracy provided by the Y-factor method and
other cold-source implementations. A scalar calibration choice
is also available that offers less accuracy but is faster, and for
N5241/42/49A, does not require the external ECal module used
as an impedance tuner. For calibration of the noise receiver,
Option 029 requires a power meter or a 346 series noise source
(346C or 346C-K01 recommended). For measurements of mixers
and converters, a power meter is always required. The noise
source and power meters are only used during calibration of the
analyzer, and must be ordered or supplied separately. During the
S-parameter portion of the noise calibration, a separate ECal
module or mechanical calibration kit is required (also must be
ordered or supplied separately). Option 029 also allows noise
figure measurements using the standard receivers for high-gain
(> 60 dB), narrowband devices that might otherwise overload the
low-noise receiver, or for noise figure measurements up to 67
GHz on the N5247A1.
1. For N5247A, the low-noise receiver works up to 50 GHz only
2. Only N4690 Series ECal modules are supported for use as an impedance
tuner.
17 | Keysight | PNA Family Microwave Network Analyzers - Configurations Guide
PNA Family Application Options, continued
PNA-X block diagrams with noise figure option
IF inputs
rear panel
+28V
J11
J10
J9
J8
J7
J4
J6
J5
RF
OUT
LO
OUT
J3
Source 1
C
J1
D
2
3
OUT 1
OUT 1
OUT 2
R3
A
35 dB
R4
R2
D
35 dB
65 dB
B
35 dB
65 dB
Test port 3
3–8.5/
13.5/
26.5 GHz
10 MHz 3 GHz
To receivers
C
Test port 1
Noise receivers
4
LO
OUT 2
Pulse
modulator
Pulse
modulator
65 dB
B
1
Source 2
R1
A
Pulse generators
Signal
combiner
+
-
J2
R
65 dB
35 dB
Test port 4
N5241/42/49A 4-port
block diagram with
noise figure option
Test port 2
Impedance tuner for noise
figure measurements
IF inputs
rear panel
+28V
J11
J10
J9
J8
J7
J4
J6
J5
RF
OUT
LO
OUT
J3
R1
J1
D
3
OUT 1
R3
Noise receivers
10 MHz - 6 - 50
GHz
6 GHz
4
LO
OUT 2
Pulse
modulator
Pulse
modulator
A
C
2
Source 2
OUT 2
60 dB
B
1
Source 1
OUT 1
A
Pulse generators
Signal
combiner
+
-
J2
R
To receivers
R4
C
R2
D
B
Tuner
35 dB
35 dB
60 dB
Test port 1
35 dB
60 dB
Test port 3
60 dB
35 dB
Test port 4
N5244/45A 4-port block
diagram with noise
figure option
Test port 2
IF inputs
rear panel
J7
Source 1
J12
J6
J5
RF2
OUT
RF1
OUT
LO
OUT
J4
J2
R
A
B
C
J1
D
Pulse generators
OUT 2
OUT 1
J3
Pulse
modulator
1
Source 2
(standard)
2
3
OUT 1
Pulse
modulator
Signal
combiner
4
LO
OUT 2
To receivers
Noise receivers
10 MHz - 6 - 50
GHz
6 GHz
Tuner
R1
A
R3
C
R4
D
R2
B
50
dB
50 dB
Test port 1
50 dB
Test port 3
50 dB
50 dB
Test port 4
50 dB
50 dB
Test port 2
50 dB
N5247A 4-port block
diagram with noise
figure option
18 | Keysight | PNA Family Microwave Network Analyzers - Configurations Guide
PNA Family Application Options, continued
Noise figure options summary
Overview
Option 028
Option 029
Description
Noise figure application using standard receivers only, for all
PNA / PNA-X models.
Noise figure application using standard or low-noise receivers, for all PNA-X models.
Required options
080, and 082 or 083 for measuring frequency converters. Not
available with N522xA-200 and -400.
For N5241/42/49A, 080 and either 219, 224, 419, 423, or H85.
For N5244/45/47A, 080 and either 224 or 423.
For measuring frequency converters, requires Option 082 or
083.
Includes low-noise receivers
No
Yes1
Includes filters for LO-harmonic
rejection
No
Yes1
Includes source tuner bypass switch
No
Yes
Use standard receivers for noise
figure measurements2
Yes
Yes
Vector noise calibration available
using ECal as tuner
Yes
Yes
Vector noise calibration using built-in tuner
No
Yes, for N5244/45/47A
Recommended ECal for vector
noise calibration3
3.5 mm N4691B-M0F (N5221/22/41/42/49A)
2.4 mm N4693A-M0F (N5224/25/44/45A)
1.85 mm N4694A-M0F (N5227/47A)
3.5 mm N4691B-M0F (N5241/42/49A)
Built-in for N5244/45/47A
Included tuner accessories for m-f ECal
3.5 mm N5242-20137 cable, 85052-60013 m-f adapter
(N5221/22/41/42/49A)
2.4 mm N5245-20140 cable, 85056-60007 m-f adapter
(N5224/25/44/45A)
1.85 mm N5247-20142 cable, 85058-60115 m-f adapter
(N5227/47A)
3.5 mm N5242-20137 cable, 85052-60013 m-f adapter
(N5241/42/49A)
N/A for N5244/45/47A, due to built-in tuner
Recommended adapter for f-f ECal tuner
(N4691B/93A/94A-00F)
3.5 mm 85052-60014 m-m adapter (N5221/22/41/42/49A)
2.4 mm 85056-60005 m-m adapter (N5224/25/44/45A)
1.85 mm 85058-60113 m-m adapter (N5227/47A)
3.5 mm 85052-60014 m-m adapter (N5241/42/49A)
N/A for N5244/45/47A, due to built-in tuner
Scalar noise calibration available
Yes
Yes
8.5/13.5/26.5/43.5/50/67
8.5/13.5/26.5/43.5/50/67
Max frequency, using low-noise
receivers (GHz)
N/A
8.5/13.5/26.5/43.5/50
Max frequency, using standard
receivers (GHz)2
8.5/13.5/26.5/43.5/50/67
8.5/13.5/26.5/43.5/50/67
Calibration accessories for low-noise
receivers
N/A
Cal kit or ECal, 346C or 346C-K01 noise source or power
meter
Calibration accessories for standard
receivers
Cal kit or ECal, power meter
Cal kit or ECal, power meter
Max input frequency (GHz)
8.5/13.5/26.5/43.5/50/67
8.5/13.5/26.5/43.5/50/67
Max output frequency, using low-noise
receivers (GHz)
N/A
8.5/13.5/26.5/43.5/50/67
Max output frequency, using standard
receivers (GHz)2
18.5/13.5/26.5/43.5/50/67
8.5/13.5/26.5/43.5/50/67
Calibration accessories for low-noise
receivers
N/A
Cal kit or ECal, power meter, 346C or 346C-K01 noise source
(optional)
Calibration accessories for standard
receivers
Cal kit or ECal, power meter
Cal kit or ECal, power meter
S-parameter, conversion gain/loss
measurements
Max freq (GHz)
NF measurements, amplifiers
NF measurements, converters
1. For N5247A, the low-noise receiver works up to 50 GHz only.
2. External preamplifier and filter(s) required if DUT excess noise (gain plus noise figure) is < 30 dB up to 20 GHz, < 40 dB up to 50 GHz, or < 45 dB up to 67 GHz.
3. Only N4690 Series ECal modules are supported for use as an impedance tuner.
19 | Keysight | PNA Family Microwave Network Analyzers - Configurations Guide
PNA Family Application Options (continued)
Pulse, antenna, mm-wave
Solid black series name indicates the feature is available on
that series, while gray series name with strikethrough
indicates the feature is not available on that series. For
example;
PNA: Available on PNA Series
PNA: Not available on PNA Series
Pulsed-RF measurements (Option 008)
PNA-X PNA PNA-L
This option adds narrowband pulse detection mode and
extends the pulsed-RF measurement capability to narrower
pulse widths below the limit for the standard wideband
detection mode. The PNA-X and PNA are complete pulsedRF solutions with built in pulse generators and modulators, so external test sets and pulse generators are not
required. With narrowband detection mode, Option 008
sets the coefficient of the analyzer’s digital-IF filters to null
out unwanted spectral components, enables the internal
receiver IF gates, controls internal pulse generators (Option
025), internal pulse modulators (Option 021 and/or 022),
and external pulse modulators, and performs optimization for measurement sensitivity. Option 008 also includes
conventional pulsed-RF measurement software (Option
H08). Option 025 is required. Option 021 is recommended
for forward-only pulsed-RF measurements. Option 021
and 022 are recommended for bi-directional pulsed-RF
measurements. The N1966A pulse I/O adapter is recommended if using external pulse generators and/or external
pulse modulators
Add IF inputs for antenna and millimeterwave (Option 020) PNA-X PNA PNA-L
This option enables external IF inputs on the rear panel
of the analyzer for applications such as antenna and
millimeter-wave test.
Add pulse modulator to internal first source
(Option 021) PNA-X PNA PNA-L
This option enables the internal pulse modulator on
Source1 Out1. Control of the modulator can also be done
via pin 8 of the Pulse I/O D-sub connector on the rear
panel of the analyzer using an external pulse generator, or
by using one of the internal pulse generators (Option 025).
The N1966A pulse I/O adapter is recommended if using an
external pulse generator.
Add pulse modulator to internal second source
(Option 022) PNA-X PNA PNA-L
This option enables the internal pulse modulator on Source2
Out1. Control of the modulator can also be done via pin 8 of the
Pulse I/O D-sub connector on the rear panel of the analyzer
using an external pulse generator, or by using one of the internal
pulse generators (Option 025). The N1966A pulse I/O adapter is
recommended if using an external pulse generator. Option 224
or 400 is required for PNA-X, and one of Option 400, 401, 417, or
419 is required for PNA.
Add four internal pulse generators (Option 025)
PNA-X PNA PNA-L
This option enables four internal pulse generators. These pulse
generators can be used to control the internal pulse modulators
and internal receiver IF gates, and are also available on pins 10
through 13 of the Pulse I/O D-sub connector on the rear panel
of the analyzer to control external modulators and/or gates. The
N1966A pulse I/O adapter is recommended if using external pulse
modulators.
8
7
15
6
14
5
13
4
12
3
11
2
10
1
9
Pulse I/O D-sub connector (DB-15 female)
Fast CW Sweep (Option 118)
PNA-X PNA PNA-L
This option uses FIFO (first-in first-out) to allow external pointtrigger acquisition of 400,000 data points per second on five
measurement receivers. When enabled, there is no display update,
no background computation, or other interference from the vector
network analyzer application. All the data gathered is placed into a
500 million points FIFO buffer. While the data is going into FIFO it
can be read from the FIFO buffer.
Nonlinear vector network analysis
Please refer to 5989-8575EN Nonlinear Vector Network
Analyzer Brochure for more information.
20 | Keysight | PNA Family Microwave Network Analyzers - Configurations Guide
PNA Family Application Options (continued)
Accessories
Solid black series name indicates the feature is available on that
series, while gray series name with strikethrough indicates the
feature is not available on that series. For example;
PNA:
PNA:
Available on PNA Series
Not available on PNA Series
Rack mount kit without handles (Option 1CM)
PNA-X PNA PNA-L
Adds a rack mount (ICM042A) and rail kit (E3663AC) for use
without handles.
Comb Generators
U9391C 10 MHz to 26.5 GHz
U9391F 10 MHz to 50 GHz
U9391G 10 MHz to 67 GHz
PNA-X PNA PNA-L
The U9391C/F/G provides precision phase calibration, traceable
to the National Institute of Standards and Technology (NIST)
standard. It is used for nonlinear measurements with the PNA-X
nonlinear vector network analyzer (NVNA). NVNA requires two
comb generators, one is connected during measurements and
another is used only during calibration. A comb generator is also
used to characterize the VNA receivers for delay measurements
of frequency converters using PNA-X or PNA with Option 083.
Rack mount kit with handles (Option 1CP)
PNA-X PNA PNA-L
Adds handles (5063-9230), a rack mount (5063-9237) and rail kit
(E3663AC) for use with handles.
Pulse I/O adapter (N1966A)
PNA-X PNA PNA-L
An adapter for connecting between the Pulse I/O connector on the rear panel
of the analyzer and the coaxial inputs and outputs of external pulse
generators and external pulse modulators. Coaxial connectors are SMB-male.
The PULSE IN connectors are for controlling the analyzer’s internal IF gates,
which are enabled with Option 008 and used with narrowband detection. The
PULSE OUT connectors are from the four internal pulse generators, which are
enabled with Option 025. The PULSE SYNC IN connector is used to
synchronize the internal pulse generators with an external timing pulse. The
RF PULSE MOD IN connector controls the internal pulse modulator(s) which
are enabled with Options 021 and 022.
Pulse I/O adapter (N1966A) simplifies connections
Comb generator enables
vector-corrected measurements at
fundamental and
harmonic frequencies
CalPod calibration refresh module (8553xB/4xA)
PNA-X PNA PNA-L
CalPods allow in-situ calibration refreshes to be performed at
the push of a button without removing the DUT or connecting
calibration standards. CalPods are useful in any measurement
situation where it is desirable to have assurance that a valid
calibration is present before recording measurement data. Some
of the measurement applications where CalPods have proven
useful are as follows:
–– Thermal-vacuum testing
–– Temperature chamber testing
–– Measurement of low-loss devices
–– Applications that require frequent re-calibrations
–– Applications that have complex and lengthy calibrations,
such as multi-port measurements
–– Measurement of cables installed in aircraft
–– Removing switch matrix repeatability errors
–– Removing switch and connector repeatability errors in
complex ATE test systems
21 | Keysight | PNA Family Microwave Network Analyzers - Configurations Guide
PNA Family Network Analyzer Upgrade Kits
Frequency, test ports, test set and power configurations
Upgrade kits are available to add options after initial purchase. To upgrade the PNA-X/PNA/PNA-L, order the corresponding
item number. The model and serial numbers of the instrument to be retrofitted are required as part of the order.
Description
Required Option
For PNA-X
Series
For PNA
Series
For PNA-L
Series
User
Installable
N5239A or N5249A
N5249AU-913
n/a
N5239AU-613
No
Frequency upgrade1
Extend analyzer's frequency range to 13.5 GHz
Extend analyzer's frequency range to 20 GHz
N5239A or N5231A
n/a
n/a
N5239AU/31AU-620
No
Extend analyzer's frequency range to 26.5 GHz
N5241A, N5249A, or
N5221A
N5241AU-960/
49AU-960
N5221AU-626
n/a
No
Extend analyzer's frequency range to 50 GHz
N5244A, N5224A or
N5234A
N5244AU-990
N5224AU-650
N5234AU-650
No
Expand 2-ports, single source without
configurable test set to 4-ports
N522xA-200
n/a
N522xAU-600
n/a
No
Expand 2-ports, single source with
configurable test set to 4-ports
N524xA-200 or
N522xA-201
N524xAU-940
N522xAU-601
n/a
No
Expand 2-ports, single source with
configurable test set and extended power range to 4-ports
N522xA-217
n/a
N522xAU-617
n/a
No
Expand 2-ports, single source with
configurable test set, extended power range and bias-tees
to 4-ports
N524xA-219 or
N522xA-219
N524xAU-942
N522xAU-619
n/a
No
Expand 2-ports, internal second source with configurable
test set, extended power range, bias-tees, combiner and
mechanical switches to 4-ports
N524xA-224
N524xAU-944
n/a
n/a
No
Test ports
Test set and power configuration
Add configurable test set, 2-ports
N522xA-200
n/a
N522xAU-201
n/a
No
Add configurable test set and source
attenuators, 2-ports
Add extended power range, 2-ports2
N523xA-200
n/a
n/a
N523xAU-216
No
N522xA-201
n/a
N522xAU-217
n/a
No
N522xA-217
n/a
N522xAU-219
n/a
No
Add extended power range and bias-tees, 2-ports
N524xA-200 or
N5227A-201
N524xAU-921
N5227AU-217/219
n/a
No
Add internal 2nd source, combiner and
mechanical switches, 2-ports
N524xA-219 or
N522xA-219
N524xAU-922
n/a
n/a
No
Add bias-tees, 2-ports
2
Add high power configurable, 2-ports
N524xA-219 or 224
N524xAU-H85
n/a
n/a
No
Add configurable test set, 4-ports
N522xA-400
n/a
N522xAU-401
n/a
No
Add configurable test set and source
attenuators, 4-ports
N523xA-400
n/a
n/a
N523xAU-416
No
Add extended power range, 4-ports2
N522xA-401
n/a
N522xAU-417
n/a
No
N522xA-417
n/a
N522xAU-419
n/a
No
Add extended power range and bias-tees, 4-ports
N524xA-400 or
N5227A-401
N524xAU-926
N5227AU-417/419
n/a
No
Add internal 2nd source, combiner and
mechanical switches, 4-ports
N524xA-419 or
N522xA-419
N524xAU-927
n/a
n/a
No
Add high power configurable, 4-ports
N524xA-419 or 423
N524xAU-H85
n/a
n/a
No
Add bias-tees, 4-ports
2
1. Frequency upgrade options from 8.5/13.5/20/26.5 GHz to 43.5/50 GHz and 43.5/50 GHz to 67 GHz are not available. Trade-in is recommended.
2. Not available on N5227A.
22 | Keysight | PNA Family Microwave Network Analyzers - Configurations Guide
PNA Family Network Analyzer Upgrade Kits (continued)
Application options
Upgrade kits are available to add options after initial purchase. To upgrade the PNA-X/PNA/PNA-L, order the corresponding
item number. The model and serial numbers of the instrument to be retrofitted are required as part of the order.
Description
Required Option
For PNA-X
Series
For PNA
Series
For PNA-L
Series
User
Installable
Windows 7 OS7.
N524xAU-007
N522xAU-007
N523xAU-007
Yes
N524xAU-010
N522xAU-010
N523xAU-010
Yes
Measurement applications
Automatic fixture removal
Time-domain measurements
Noise figure measurements using standard receivers
Option 0801,2
N524xAU-028
N522xAU-028
n/a
Yes
Fully-corrected noise figure measurements
for PNA-X, 2-ports
Option 080 and for N5241/42/49A, one of Options 219, 224 or H851.
For N5244/45/47A, 080 and 224
N524xAU-9243
n/a
n/a
No
Fully-corrected noise figure measurements
for PNA-X, 4-ports
Option 080 and for N5241/42/49A, one of Options 419, 423 or H851.
For N5244/45/47A, 080 and 423
N524xAU-9293
n/a
n/a
No
N524xAU-080
N522xAU-080
N523xAU-080
Yes
N524xAU-082
N522xAU-082
N523xAU-082
Yes
Frequency offset
Scalar-calibrated converter measurements
Option 080
Vector- and scalar-calibrated converter measurements
Option 080
N524xAU-083
N522xAU-083
n/a
Yes
Embedded LO measurements
Option 082 or 083
N524xAU-084
N522xAU-084
n/a
Yes
Gain compression application
See Footnote 1
N524xAU-086
N522xAU-086
n/a
Yes
Intermodulation distortion application
Option 0801,4
N524xAU-087
N522xAU-087
n/a
Yes
8
Source phase control
See Footnote 5
N524xAU-088
N522xAU-088
n/a
Yes
Differential and I/Q devices application
Option 080 and 400, 401, 410, 417, or 419, and
Windows 7 OS7
N524xAU-089
N522xAU-089
n/a
Yes
Spectrum analyzer
Option 080, Windows 7 OS, and
DSP version 57, 9
N524xAU-090
N522xAU-090
n/a
Yes
Integrated true-mode stimulus application
Option 400, 401, 417, 419, or 423
N524xAU-460
N522xAU-460
n/a
Yes
N-port capabilities
See Footnote 6
N524xAU-551
N522xAU-551
N523xAU-551
Yes
Pulse, antenna, mm-wave
Pulsed-RF measurements
N524xAU-008
N522xAU-008
n/a
Yes
Add IF inputs
N524xAU-020
N522xAU-020
n/a
Yes
Add pulse modulator to internal 1st source
N524xAU-021
N522xAU-021
n/a
Yes
Add pulse modulator to internal 2nd source
Option 0251
N524xAU-022
N522xAU-022
n/a
Yes
Add four internal pulse generators
Option 224, 400, 401, 417, 419, or 423
N524xAU-025
N522xAU-025
n/a
Yes
Fast CW sweep
N524xAU-118
N522xAU-118
n/a
Yes
1. For measuring frequency converters, Option 082 or 083 is required.
2. Requires configurable test set for signal conditioning of noise figure measurements using standard receivers. Therefore it is not available with N522xA-200, -210,
-400 and -410.
3. Upgrading N5244A units with noise figure hardware requires serial-number prefixes of 5204 or higher, and upgrading N5245A units requires serial-number prefixes of
5205 or higher. For these two models, units with lower serial-number prefixes can be traded in for credit towards a new unit with the noise figure hardware.
4. Two-tone signal must be routed to R1 receiver after an external combiner; therefore it is not available with N522xA-200, -210, -400 and -410.
5. When used with an external signal generator, configurable test set is required to access a receiver. Therefore it is not available with N522xA-200 and -210.
6. To connect a multiport test set, configurable test set is required. Therefore it is not available with N522xA-200, -210, -400, -410, and N523xA-200, and -400.
7. The Windows 7 upgrade kit is model N8983A. This upgrade kit contains a new disk drive and requires an i7 or Celeron CPU. For units with older CPUs, order Option
PC6 for a new i7 CPU. When adding Option 090 on units with an older CPU, order Options PC6 and SP5.
8. A configurable test set is required for VMC measurements (to connect a reference mixer) or for SMC+Phase measurements using the comb-generator-based calibration. When ordered with N522xA-200, -210, -400 and -410, Option 083 adds phase and delay measurements only by using SMC+Phase with a calibration mixer.
9. Optional receiver attenuators are recommended to avoid receiver compression for large-scale measurements.
23 | Keysight | PNA Family Microwave Network Analyzers - Configurations Guide
PNA Family Network Analyzer Upgrade Kits (continued)
Application options
Upgrade kits are available to add options after initial purchase. To upgrade the PNA-X/PNA/PNA-L, order the corresponding item
number. The model and serial numbers of the instrument to be retrofitted are required as part of the order.
Required Option
For PNA-X
Series
For PNA
Series
For PNA-L
Series
User
Installable
Nonlinear component characterization
Options 419 and 080, or 400, H85 and 080
N524xAU-510
n/a
n/a
Yes
Nonlinear X-parameters
Options 423 and 510
N524xAU-514
n/a
n/a
Yes
Nonlinear pulse envelope domain
Requries Options 021, 025 and either one of
510 or 514
N524xAU-518
n/a
n/a
Yes
Arbitrary load-impedance X-parameters
Option 514
N524xAU-520
n/a
n/a
Yes
Perpetual license for built-in performance test software
for Keysight inclusive calibration
N524xAU-897
N522xAU-897
N523xAU-897
Yes
Perpetual license for built-in performance test
software for standard compliant calibration
N524xAU-898
N522xAU-898
N523xAU-898
Yes
Description
Nonlinear vector network analysis
Calibration software
24 | Keysight | PNA Family Microwave Network Analyzers - Configurations Guide
PNA Family Network Analyzer Upgrade Kits (continued)
Upgrade paths
PNA-X upgrade path
Frequency
2-ports
8.5 GHz
200
N5249AU-913
940
400
921
13.5 GHz
1
924
219/029
N5241AU-960
1
26.5 GHz
4-ports
N5249AU-960
43.5 GHz
922
224/029
219
926
942
922
2
924
224
N5244AU-990
9291 419/029
419
1
927
927
944
9292
423
423/029
H85
50 GHz
High power configurable
67 GHz
Frequency
PNA upgrade path
43.5 GHz
13.5 GHz
N5221AU-626
26.5 GHz
2-ports
600
200
N5224AU-650
201
201
50 GHz
217
217
67 GHz
219
219
Frequency
8.5 GHz
PNA-L upgrade path
43.5 GHz
N5239AU-613
13.5 GHz
N5234AU-650
50 GHz
601
617
619
4-ports
400
401
401
417
417
419
419
2-ports
4-ports
200
400
216
216
416
416
N5231AU-620
20 GHz
N5239AU-620
1. This upgrade path only available on N5241/42/49A.
2. Upgrading N5244A units with noise figure hardware requires serial-number prefixes of 5204 or higher, and upgrading N5245A units requires
serial-number prefixes of 5205 or higher. For these two models, units with lower serial-number prefixes can be traded in for credit towards a new
unit with the noise figure hardware.
25 | Keysight | PNA Family Microwave Network Analyzers - Configurations Guide
Applications
Material measurements
Multiport measurements
85070E High-Temperature Dielectric Probe Kit
Multiport test sets are designed to work with the PNA family of
network analyzers to provide network analysis with a single set
of connections for devices that have multiple ports. The test sets
are configured in a variety of ways, for extension or switching,
electro-mechanical or solid-state switches, number of test ports,
frequency range, and 2- or 4-ports, depending on your analyzer.
The 85070E enables measurements of the dielectric properties
of materials quickly and conveniently. Measurements made with
this probe are nondestructive and require no sample preparation.
The dielectric probe is well suited for measurements of liquid,
semisolid and flat solid materials. Measurement results can be
viewed in a variety of formats (ε’r, ε”r, tan δ or Cole-Cole). The
supplied software can be run in the PNA analyzer or on a PC.
85071E Materials Measurement Software
The 85071E materials measurement software calculates the permittivity and permeability of material samples placed in a coaxial
airline or a rectangular waveguide. The measurement technique
works well for solid materials that can be machined to fit precisely
inside a transmission line. Measurement results can be viewed
in a variety of formats (ε’r, εr, µ’r, µ”r, tan δ, or Cole-Cole µ). The
software can be run in the PNA analyzer or on a PC.
Signal integrity measurements
N1930B Physical Layer Test System (PLTS) Software
The PLTS software platform has become an industry standard for
calibration, measurement and analysis of linear passive interconnects such as cables, connectors, backplanes and printed circuit
boards. Utilizing either a vector network analyzer (VNA) or a time
domain reflectometer (TDR), fast and accurate measurements
can be obtained without in-depth knowledge of microwave
measurement techniques. Refer to www.keysight.com/find/plts or
the technical overview, literature number 5989-6841EN for more
details.
Test set types: switching and extension test sets
Switching test sets provide an economical solution for RF
applications. They are connected directly to the test ports of the
VNA, and a group of test ports share the directional couplers
and receivers in the VNA. An extension test set is connected to
the sources and test receivers through the configurable test set
of the VNA. It features a directional coupler for every test port
and all switching occurs behind the directional couplers, which
provides the ultimate in flexibility, stability, and performance for
RF and microwave applications.
Switch types: electro-mechanical and
solid-state switches
Electro-mechanical switches have less insertion loss, higher
power handling, and a more linear response compared to solidstate switches. They are recommended for testing active devices,
high-power devices, and devices that require wide dynamic
range. However, they have limited switching life (mostly 5 million
cycles) and long setting times. In contrast, solid-state switches
have unlimited switching life, very fast switching speed and
excellent repeatability. Thus, they are often used for high-volume
S-parameter measurements of passive devices.
Test set model number
Multiport test set model numbers represent the type of test set;
note the numbering scheme below.
Note that there are some test sets that do not follow this numbering scheme such as U3022AE10, U3025AE06,
and U3025AE10, which use solid-state switches, and U3022AS66, which includes 1x6 switching test set and six
calibration distribution ports.
26 | Keysight | PNA Family Microwave Network Analyzers - Configurations Guide
Test set options
One of the following test set options must be selected.
Standard configuration (Option 700)
–– The standard configuration is the basic test set configuration,
which does not include signal conditioning devices such as
amplifiers.
Add amplifiers for improved dynamic range (Option 001)
–– Option 001 adds an amplifier between each test port coupler
and the receiver switch to improved system dynamic range. It
is primarily offered for the test set with solid-state switches
to compensate for the insertion loss.
Add amplifiers and bias-tees (Option 002)
–– Option 002 adds an amplifier between each test port coupler
and the receiver switch to improved system dynamic range
and bias-tees for all test ports on the test set as well as the
analyzer. It is primarily offered for the test set with solid-state
switches to compensate for the insertion loss.
Interface kits
The interface kit includes a set of semi-rigid RF jumper cables and
two pairs of rear locking feet that connect and lock the analyzer
and the test set together. When ordering a multiport test set, the
analyzer that is used with the test set must be specified to add
one of the following interface kits. The availability depends on
the test set model. There are following three interface kit models
based on the jumper connector layouts on the test set. Therefore,
only one interface kit model (“PX”, “PN”, or “PL”) is available
on each test set. Each interface kit model has one digit suffix
indicating the connector type; 1 for 1.85 mm, 2 for 2.4 mm and 3
for 3.5 mm (or SMA).
Millimeter-wave measurements
Single sweep solution to 110 GHz
The 67 GHz PNA and PNA-X network analyzers allow extending
the maximum frequency to 110 GHz with a 1.0 mm coaxial connector, enabling 10 MHz to 110 GHz single sweep measurements
using a millimeter-wave controller and frequency extenders with
built-in combiner.
The 10 MHz to 110 GHz broadband millimeter-wave system provides high performance and capabilities including power control,
4-port true-differential, and frequency converter measurements.
It is configured with an N5227A PNA with Option 201 (2-ports)
or Option 401 (4-ports), or N5247A with Option 200 (2-ports) or
Option 400 (4-ports), Option 020 IF access, an N5261A 2-port
or an N5262A 4-port millimeter-wave test set controller with
1.85 mm coaxial cables (Option 112 for N5261A, Option 114 for
N5262A) and RF/LO/IF/DC cables sets (to select the cable length
and quantities), and one (for 2-ports) or two (for 4-ports) each of
right and left frequency extenders with required attenuators and
bias-tee configurations.
Waveguide banded solutions to 1.05 THz
The waveguide banded millimeter-wave solution covers waveguide bands from 50 GHz to 1.05 THz. A 2- or 4-port PNA or
PNA-X in conjunction with N5261A (for 2-port) or N5262A
(for 4-port) configures for the most complete millimeter wave
solution. It is configured with a PNA Series with Option 020 IF
access, configurable test set (Option 201 or 401), and frequency
offset mode (Option 080), or PNA-X Series with 2-port (Option
200) or 4-port (Option 400) and IF access (Option 020). For the
millimeter-wave test controller, appropriate RF cable option and
RF/LO/IF/DC cable set option for frequency extenders must be
selected for the analyzer’s connector type, number of test ports,
and lengths. Add appropriate frequency extenders with required
quantity for the measurements.
For complete list of millimeter-wave products and options, and
ordering instructions, please refer to 5989-7620EN Millimeterwave Network Analyzers Technical Overview.
U3021PXx
Interface kit for test set with jumper connectors to align with N524xA PNA-X and N522xA PNA
U3021PNx
Interface kit for test set with jumper connectors to align with E836xB/C PNA and N5230A/C-x25 2-port PNA-L
Option 261
For use with E8361A/C 2-port PNA
Option 262
For use with E8362B/C 2-port PNA or N5230A/C-225 2-port PNA-L
Option 263
For use with E8363B/3C/4B/4C 2-port PNA or N5230A/C-425/525 2-port PNA-L
Option 430
For use with N5230A/C-245/246 4-port PNA-L
Option 242
For use with N5241/42/49A-2xx 2-port PNA-X or N5221A/2A-2xx 2-port PNA
Option 442
For use with N5241/42/49A-400 4-port PNA-X or N5221A/2A-4xx 4-port PNA
Option 245
For use with N5244A/5A-200 2-port PNA-X or N5224A/5A-2xx 2-port PNA
Option 445
For use with N5244A/5A-400 4-port PNA-X or N5224A/5A-4xx 4-port PNA
Option 247
For use with N5247A-200 2-port PNA-X or N5227A-2xx 2-port PNA
Option 447
For use with N5247A-400 4-port PNA-X or N5227A-4xx 4-port PNA
When ordering an additional cable set, a spare cable or rear locking feet, refer to the multiport test set user’s guide or go to:
www.keysight.com/find/multiport
27 | Keysight | PNA Family Microwave Network Analyzers - Configurations Guide
Measurement Accessories
A complete list of RF and microwave test accessories is available
on our Web site:
www.keysight.com/find/accessories
Accessories are available in these connector types:
50 Ω Type-N, 3.5 mm, 7 mm, 2.4 mm, 2.92 mm, 1.85 mm, 1.0 mm,
and waveguide. Test port cables and a calibration kit should be
added for a complete measurement system. A verification kit is
used to verify corrected system performance.
Cables and adapter sets
Keysight offers cables in the following types:
–– single cables in semi-rigid and flexible
–– cable sets in semi-rigid and flexible
There are also adapter sets available that protect the test port
and convert the port to the desired connector interface. These
kits contain:
–– one male adapter
–– one female adapter
To attain the best mechanical rigidity for device connection, use a
single cable and the appropriate special adapter set. To attain the
greatest flexibility for device connection, use a cable set.
Calibration kits
Coaxial measurements
Mechanical calibration kits include standards, such as opens,
shorts and loads, which are measured by the network analyzer for
increased measurement accuracy.
Electronic calibration (ECal) kits replace mechanical calibration standards with one solid-state calibration module that is
controlled by the network analyzer via USB, to present many
different impedances to the test ports. A full two-port calibration
can be performed quickly with a single connection. This technique reduces operator errors and connector wear and abrasion.
Choose a calibration kit for each connector type to be used.
Economy, includes:
–– open standards (male and female)
–– short standards (male and female)
–– fixed-termination standards (male and female)
Standard, includes the devices in the economy kit and adds:
–– sliding load standards (male and female) or a series of offset
shorts
Precision, includes the devices in the economy kit and adds:
–– 50 Ω airline(s) for TRL calibration
–– TRL adapters
Waveguide measurements
Network analyzer
test set
Device
under
test
Network analyzer
test set
Test port
adapter
Cable set
Single cable
Device
under
test
For waveguide measurements, Keysight offers mechanical
calibration kits that include:
–– waveguide-to-coax adapters (X, P, K, R, Q, U, V)
–– precision waveguide section
–– flush short circuit
–– fixed terminations
–– straight section
28 | Keysight | PNA Family Microwave Network Analyzers - Configurations Guide
For devices with 1.0 mm connectors
For devices with 1.85 mm connectors
Mechanical calibration/verification kit
Mechanical calibration kit
85059A DC to 110 GHz precision calibration/verification kit.
Includes:
–– 85059-60003 1.00 mm (m) short 2.450 mm
–– 85059-60007 1.00 mm (f) short 2.450 mm
–– 85059-60004 1.00 mm (m) short 3.000 mm
–– 85059-60008 1.00 mm (f) short 3.000 mm
–– 85059-60002 1.00 mm (m) short 1.825 mm
–– 85059-60006 1.00 mm (f) short 1.825 mm
–– 85059-60001 1.00 mm (m) short 1.300 mm
–– 85059-60005 1.00 mm (f) short 1.300 mm
–– 85059-60009 1.00 mm male open
–– 85059-60010 1.00 mm female open
–– 85059-60019 1.00 mm male load
–– 85059-60020 1.00 mm female load
–– 85059-60021 1.00 mm lossy delay line
–– 11920-60001 1.00 mm (m) to 1.00 mm (m) adapter
–– 11920-60002 1.00 mm (f) to 1.00 mm (f) adapter
–– 11920-60003 1.00 mm (m) to 1.00 mm (f) adapter
–– 11500-60001 1.00 mm (f) to 1.00 mm (f) 8.8 cm cable
–– 85059-60016 1.00 mm mismatch thru adapter for
verification
–– 85059-60017 1.00 mm matched thru adapter for verification
–– 8710-2079
6 mm, 4 in-lb torque wrench
–– 8710-2156
6 mm open end wrench
85058B standard: DC to 67 GHz. Includes:
–– 85058-60101 1.85 mm (m) short 5.4 mm
–– 85058-60102 1.85 mm (m) short 6.3 mm
–– 85058-60103 1.85 mm (m) short 7.12 mm
–– 85058-60104 1.85 mm (m) short 7.6 mm
–– 85058-60105 1.85 mm (f) short 5.4 mm
–– 85058-60106 1.85 mm (f) short 6.3 mm
–– 85058-60107 1.85 mm (f) short 7.12 mm
–– 85058-60108 1.85 mm (f) short 7.6 mm
–– 85058-60109 1.85 mm male open
–– 85058-60110 1.85 mm female open
–– 85058-60111 1.85 mm male load
–– 85058-60112 1.85 mm female load
–– 85058-60113 1.85 mm (m) to 1.85 mm (m) adapter
–– 85058-60114 1.85 mm (f) to 1.85 mm (f) adapter
–– 85058-60115 1.85 mm (m) to 1.85 mm (f) adapter
Cables
–– 11500I –– 11500J –– 11500K –– 11500L 1.0 mm (f-f) test port cable (8.8 cm)
1.0 mm (m-f) test port cable (16.0 cm)1
1.0 mm (m-f) test port cable (20.0 cm)1
1.0 mm (m-f) test port cable (24.0 cm)1
Adapter set
–– V281C –– V281D –– W281C –– W281D –– 11920A –– 11920B –– 11920C –– 11921A –– 11921B –– 11921C –– 11921D –– 11922A –– 11922B –– 11922C –– 11922D –– 11923A 1.0 mm(f) to V-band waveguide adapter
1.0 mm (m) to V-band waveguide adapter
1.0 mm (f) to W-band waveguide adapter
1.0 mm (m) to W-band waveguide adapter
1.0 mm (m) to 1.0 mm (m) adapter
1.0 mm (f) to 1.0 mm (f) adapter
1.0 mm (m) to 1.0 mm (f) adapter
1.0 mm (m) to 1.85 mm (m) adapter
1.0 mm (f) to 1.85 mm (f) adapter
1.0 mm (m) to 1.85 mm (f) adapter
1.0 mm (f) to 1.85 mm (m) adapter
1.0 mm (m) to 2.4 mm (m) adapter
1.0 mm (f) to 2.4 mm (f) adapter
1.0 mm (m) to 2.4 mm (f) adapter
1.0 mm (f) to 2.4 mm (m) adapter
1.0 mm (f) connector launch assembly
1. For on-wafer applications, two 11500J/K/L cables are required; one cable
for each test port.
2. Special rugged female connector specifically for connecting to the
network analyzer test port, but does not mate with a standard male
connector.
85058E economy: DC to 67 GHz. Includes:
–– 85058-60101 1.85 mm (m) short 5.4 mm
–– 85058-60105 1.85 mm (f) short 5.4 mm
–– 85058-60109 1.85 mm male open
–– 85058-60110 1.85 mm female open
–– 85058-60123 1.85 mm male load
–– 85058-60124 1.85 mm female load
–– 85058-60113 1.85 mm (m) to 1.85 mm (m) adapter
–– 85058-60114 1.85 mm (f) to 1.85 mm (f) adapter
–– 85058-60115 1.85 mm (m) to 1.85 mm (f) adapter
Electronic calibration kits
N4694A Microwave ECal: 10 MHz to 67 GHz, 2-ports Includes:
–– Option M0F module with:
N4694-60001 1.85 mm (f) to 1.85 mm (m) ECal module
–– Option 00M module with:
N4694-60002 1.85 mm (m) to 1.85 mm (m) ECal module
–– Option 00F module with:
N4694-60003 1.85 mm (f) to 1.85 mm (f) ECal module
–– Option 00A adds:
–– 85058-60113 1.85 mm (m) to 1.85 mm (m) adapter
–– 85058-60114 1.85 mm (f) to 1.85 mm (f) adapter
Cables
–– N4697E2 Single, flexible:
1.85 mm (f) to 1.85 mm (f), 96.5 cm, 38 inches
–– N4697F2 Set, flexible:
–– One 1.85 mm (f) to 1.85 mm (f) cable, 62.2 cm, 24.5 inches,
p/n N4697-60100
–– One 1.85 mm (f) to 1.85 mm (m) cable, 62.2 cm, 24.5 inches,
p/n N4697-60200
–– N4421B-K67 Single, flexible:
1.85 mm (f) to 1.85 mm (m), 91.4 cm, 36 inches
Adapter set
–– 85130H2 1.85 mm to 1.85 mm
29 | Keysight | PNA Family Microwave Network Analyzers - Configurations Guide
For devices with 2.4 mm connectors
Mechanical calibration kit
85056A standard: DC to 50 GHz. Includes:
–– 00901-60003 2.4 mm (m) fixed broadband load
–– 00902-60004 2.4 mm (f) fixed broadband load
–– 00915-60003 2.4 mm (m) sliding load
–– 00915-60004 2.4 mm (f) sliding load
–– 85056-60005 2.4 mm (m) to 2.4 mm (m) adapter
–– 85056-60006 2.4 mm (f) to 2.4 mm (f) adapter
–– 85056-60007 2.4 mm (m) to 2.4 mm (f) adapter
–– 85056-60020 2.4 mm (m) short
–– 85056-60021 2.4 mm (f) short
–– 85056-60022 2.4 mm (m) open
–– 85056-60023 2.4 mm (f) open
85056D economy: DC to 50 GHz. Includes:
–– 00901-60003 2.4 mm (m) fixed broadband load
–– 00902-60004 2.4 mm (f) fixed broadband load
–– 85056-60005 2.4 mm (m) to 2.4 mm (m) adapter
–– 85056-60006 2.4 mm (f) to 2.4 mm (f) adapter
–– 85056-60007 2.4 mm (m) to 2.4 mm (f) adapter
–– 85056-60020 2.4 mm (m) short
–– 85056-60021 2.4 mm (f) short
–– 85056-60022 2.4 mm (m) open
–– 85056-60023 2.4 mm (f) open
Electronic calibration kits
N4693A Microwave ECal: 10 MHz to 50 GHz, 2-ports.
Includes:
–– Option M0F module with:
N4693-60001 2.4 mm (f) to 2.4 mm (m) ECal module
–– Option 00M module with:
N4693-60002 2.4 mm (m) to 2.4 mm (m) ECal module
–– Option 00F module with:
N4693-60003 2.4 mm (f) to 2.4 mm (f) ECal module
–– Option 00A adds:
–– 85056-60005 2.4 mm (m) to 2.4 mm (m) adapter
–– 85056-60006 2.4 mm (f) to 2.4 mm (f) adapter
Cables
Note: Keysight offers the following 2.4 mm test port cables.
Adapters will be necessary when using these cables for 2.92 mm
measurements.
–– 85133C1 single, semi-rigid:
2.4 mm (f) to PSC-2.4 mm (f), 81 cm, 32 inches
–– 85133D1 set, semi-rigid:
One 2.4 mm (f) to 2.4 mm (m), 53 cm, 21 inches,
p/n 85133-60001
One 2.4 mm (f) to 2.4 mm (f), 53 cm, 21 inches,
p/n 85133-60002
–– 85133E1 single, flexible:
2.4 mm (f) to PSC-2.4 mm (f), 97 cm, 38 inches
–– 85133F1 set, flexible:
One 2.4 mm (f) to 2.4 mm (f), 63 cm, 25 inches,
p/n 85133-60016
One 2.4 mm (f) to 2.4 mm (m), 63 cm, 25 inches,
p/n 85133-60017
–– 85133H1 Single, flexible: 2.4 mm (f) to 2.4 mm (m), 63
cm, 25 inches
–– N4421AK20 Single, flexible: 2.4 mm (f) to 2.4 mm (m),
91.4 cm, 36 inches
Adapter set
–– 85130E 2.4 mm1 to 7 mm
–– 85130F 2.4 mm1 to 3.5 mm
–– 85130G 2.4 mm1 to 2.4 mm
For devices with K connectors (2.92 mm)
Mechanical calibration kits
85056KE01 DC to 40 GHz
For use with user supplied 2.9 mm test port cables.
2.92 mm (K connector) calibration kit with fixed and sliding
loads. The Keysight 85056KE01 calibration kit is an ordering
convenience to allow the pass through ordering from
Keysight for the Maury 8770C47 calibration kit.
85056KE02 DC to 40 GHz
For use with user supplied 2.92 mm test ports cables.
2.92 mm (K connector) calibration kit with fixed loads only.
The Keysight 85056KE02 calibration kit is an ordering
convenience to allow the pass through ordering from
Keysight for the Maury 8770D47 calibration kit.
The 85056KE01 and 85056KE02 contains one NMD
2.4 mm2 (f) to 2.92 mm (f) and one NMD 2.4 mm2 (f) to 2.92
mm (m) test port adapter to adapt the 2.4 mm test ports of
the PNA to 2.92 mm. It also supplies 2.92 mm to 2.92 mm
in-series adapters (3 adapters) and a PNA Cal Coefficients
on a USB stick. Users must supply their own 2.92 mm or
K-connector test port cables. Also included is a 2.92 mm
torque wrench.
Maury Microwave Terms and Conditions for Warranty and
Return apply. Maury Microwave Corp. calibration kits are to
be returned directly to Maury Microwave for service, repair,
or calibration issues and not to Keysight Technologies. For
additional information go to www.maurymicrowave.com.
Keysight Technologies does not guarantee the performance
of the Maury calibration kits or the system performance
when connected to Keysight Microwave PNA Series network
analyzers.
1. Special rugged female connector specifically for connecting to the network analyzer test port, but does not mate with a standard male connector.
2. Special rugged female connector specifically for connecting to the network analyzer test port, but does not mate with standard 2.4 mm male connector
30 | Keysight | PNA Family Microwave Network Analyzers - Configurations Guide
For devices with K connectors (2.92 mm), continued
Mechanical calibration kits, continued
Electronic calibration kits
N4692A Microwave ECal: 10 MHz to 40 GHz, 2-ports.
Includes:
–– Option M0F module with: N4692-60001 2.92 mm (f) to
2.92 mm (m) ECal module
–– Option 00M module with: N4692-60002 2.92 mm (m) to
2.92 mm (m) ECal module
–– Option 00F module with: N4692-60003 2.92 mm (f) to
2.92 mm (f) ECal module
–– Option 00A adds:
–– N4692-60021 2.92 mm (m) to 2.92 mm (m) adapter
–– N4692-60022 2.92 mm (f) to 2.92 mm (f) adapter
Cables
Note: Keysight offers the following 2.4 mm test port cables. Adapters will be
necessary when using these cables for 2.92 mm measurements.
–– 85133C1 single, semi-rigid: 2.4 mm (f) to PSC-2.4 mm (f),
81 cm, 32 inches
–– 85133D1 set, semi-rigid:
–– One 2.4 mm (f) to 2.4 mm (m), 53 cm, 21 inches,
p/n 85133-60001
–– One 2.4 mm (f) to 2.4 mm (f), 53 cm, 21 inches,
p/n 85133-60002
–– 85133E1 single, flexible: 2.4 mm (f) to PSC-2.4 mm (f), 97 cm,
38 inches
–– 85133F1 set, flexible:
–– One 2.4 mm (f) to 2.4 mm (f), 63 cm, 25 inches,
p/n 85133-60016
–– One 2.4 mm (f) to 2.4 mm (m), 63 cm, 25 inches,
p/n 85133-60017
–– 85133H1 Single, flexible: 2.4 mm (f) to 2.4 mm (m),
63 cm, 25 inches
–– N4421AK20 Single, flexible: 2.4 mm (f) to 2.4 mm (m),
91.4 cm, 36 inches
Adapters
–– 11904A 2.4 mm (m) to 2.92 mm (m)
–– 11904B 2.4 mm (f) to 2.92 mm (f)
–– 11904C 2.4 mm (m) to 2.92 mm (f)
–– 11904D 2.4 mm (f) to 2.92 mm (m)
–– 11904S 2.4 mm to 2.92 mm
–– Adapter set, contains 4 matched adapters
1. Special rugged female connector specifically for connecting to the
network analyzer test port, but does not mate with a standard male
connector.
For devices with 3.5 mm, SMA, or
2.92 mm connectors
CalPod calibration refresh modules
CalPod calibration refresh modules allow in-situ calibration
refreshes to be performed at the push of a button without removing the DUT or connecting calibration standards. They're useful
for removing environmental effects such as cable movement,
thermal effects of cables, connectors, and adapters, as well as
connector and switch matrix repeatability errors, or whenever it
is desirable to ensure a current and valid calibration is present.
The modules are especially useful in thermal or thermal-vacuum
chamber testing.
–– 85530B 20 GHz Ambient temperature CalPod calibration refresh module
–– 85531B 20 GHz Temperature-compensated CalPod
calibration refresh module
–– 85532B 20 GHz Thermal-vacuum compatible CalPod
calibration refresh module
–– 85540A 40 GHz Ambient temperature CalPod calibration
refresh module
–– 85541A 40 GHz Temperature-compensated CalPod
calibration refresh module
–– 85542A 40 GHz Thermal-vacuum compatible CalPod
calibration refresh module
–– 85523B CalPod controller; Provides control for up to four
CalPods
–– 85556A CalPod drive cable splitter; Allows control for up to
12 CalPods
–– 85554A CalPod drive cable extension; 10 meter extension
cable; cascadable.
31 | Keysight | PNA Family Microwave Network Analyzers - Configurations Guide
For devices with 3.5 mm or SMA connectors
Mechanical calibration kits
85052B standard: DC to 26.5 GHz. Includes:
–– 00902-60003 3.5 mm (m) fixed load
–– 00902-60004 3.5 mm (f) fixed load
–– 00911-60019 3.5 mm (m) sliding load
–– 00911-60020 3.5 mm (f) sliding load
–– 85052-60006 3.5 mm (m) short
–– 85052-60007 3.5 mm (f) short
–– 85052-60008 3.5 mm (m) open
–– 85052-60009 3.5 mm (f) open
–– 85052-60012 3.5 mm (f) to 3.5 mm (f) adapter
–– 85052-60013 3.5 mm (f) to 3.5 mm (m) adapter
–– 85052-60014 3.5 mm (m) to 3.5 mm (m) adapter
85052C precision TRL: DC to 26.5 GHz. Includes:
–– 00902-60003 3.5 mm (m) fixed load
–– 00902-60004 3.5 mm (f) fixed load
–– 85052-60006 3.5 mm (m) short
–– 85052-60007 3.5 mm (f) short
–– 85052-60008 3.5 mm (m) open
–– 85052-60009 3.5 mm (f) open
–– 85052-60032 3.5 mm (f) to 3.5 mm (f) adapter
–– 85052-60033 3.5 mm (m) to 3.5 mm (m) adapter
–– 85052-60034 3.5 mm (f) to 3.5 mm (m) adapter
–– 85052-60035 3.5 mm short TRL line
–– 85052-60036 3.5 mm long TRL line
85052D economy: DC to 26.5 GHz. Includes:
–– 00902-60003 3.5 mm (m) fixed load
–– 00902-60004 3.5 mm (f) fixed load
–– 85052-60006 3.5 mm (m) short
–– 85052-60007 3.5 mm (f) short
–– 85052-60008 3.5 mm (m) open
–– 85052-60009 3.5 mm (f) open
–– 85052-60012 3.5 mm (f) to 3.5 mm (f) adapter
–– 85052-60013 3.5 mm (f) to 3.5 mm (m) adapter
–– 85052-60014 3.5 mm (m) to 3.5 mm (m) adapter
Electronic calibration kits
85093C RF ECal: 300 kHz to 9 GHz, 2-ports; Standard module
includes:
–– Option M0F with: 85093-60008 3.5 mm (f) to 3.5 mm (m)
ECal module
–– Option 00F module with: 85093-60010 3.5 mm (f) to 3.5
mm (f) ECal module
–– Option 00M module with: 85093-60009 3.5 mm (m) to 3.5
mm (m) ECal module
–– Option 00A adds:
–– 85052-60012 3.5 mm (f) to 3.5 mm (f) adapter
–– 85052-60014 3.5 mm (m) to 3.5 mm (m) adapter
85093C-xxx mixed-connector options:
Port A option
Port B option
Type
(f)
(m)
Type
(f)
(m)
Type
(f)
(m)
3.5 mm
101
102
Type-N
50 ohm
203
204
7-16
205
206
N4431B Microwave ECal: 300 kHz to 13.5 GHz, 4-ports
Includes: Option 010 module with:
N4431-60006 4 x 3.5 mm (f) ECal module
N4431B-xxx mixed-connector options:
Connector type
Port A
option
Port B
option
Port C
option
Port D
option
3.5 mm (f)
101
201
301
401
3.5 mm (m)
102
202
302
402
Type-N 50 ohm (f)
103
203
303
403
Type-N 50 ohm (m)
104
204
304
404
7-16 (f)
105
205
305
405
7-16 (m)
106
206
306
406
N4433A Microwave ECal: 300 kHz to 20 GHz, 4-ports.
Includes: Option 010 module with:
N4433-60003 4 x 3.5 mm (f) ECal module
N4433A-xxx mixed-connector options:
Connector type
Port A
option
3.5 mm (f)
101
3.5 mm (m)
102
Port B
option
Port C
option
Port D
option
201
301
401
202
302
402
N4691B Microwave ECal: 300 kHz to 26.5 GHz, 2-ports.
Includes:
–– Option M0F module with:
N4691-60004 3.5 mm (f) to 3.5 mm (m) ECal module
–– Option 00M module with:
N4691-60005 3.5 mm (m) to 3.5 mm (m) ECal module
–– Option 00F module with:
N4691-60006 3.5 mm (f) to 3.5 mm (f) ECal module
–– Option 00A adds:
–– 85052-60012 3.5 mm (f) to 3.5 mm (f) adapter
–– 85052-60014 3.5 mm (m) to 3.5 mm (m) adapter
32 | Keysight | PNA Family Microwave Network Analyzers - Configurations Guide
Cables
–– 85131C1 single, semi-rigid: 3.5 mm (f) to PSC-3.5 mm (f),
81 cm, 32 inches2
–– 85131D1 set, semi-rigid:
–– One 3.5 mm (f) to 3.5 mm (m), 53 cm, 21 inches,
p/n 85131-60009
–– One 3.5 mm (f) to PSC-3.5 mm (f), 53 cm, 21 inches,
p/n 85131-60010
–– 85131E1 single, flexible: 3.5 mm (f) to PSC-3.5 mm (f),
96.5 cm, 38 inches2
–– 85131F1 set, flexible:
–– One 3.5 mm (f) to 3.5 mm (m), 62.2 cm, 24.5 inches,
p/n 85131-60012
–– One 3.5 mm (f) to PSC-3.5 mm (f), 62.2 cm, 24.5 inches,
p/n 85131-60013
–– 85131H1 single, flexible: 3.5 mm (f) to 3.5 mm (m), 62.2 cm,
24.5 inches
–– 85134E1 single, flexible: PSC-3.5 mm (f) to 2.4 mm (f), 96 cm,
38 inches
–– 85134F1 set, flexible:
–– One 2.4 mm (f) to PSC-3.5 mm (f), 53 cm, 21 inches,
p/n 85134-60004
–– One 2.4 mm (f) to PSC-3.5 mm (m), 53 cm, 21 inches,
p/n 85134-60003
–– 85134H1 single, flexible: 2.4 mm (f) to PSC-3.5 mm (m),
53 cm, 21 inches
–– N4419AK20 single, flexible: 3.5 mm (m) to 3.5 mm (f),
91.4 cm, 36 inches
–– Z5623A-K20 single, flexible: 3.5 mm (m) to 3.5 mm (m),
91.4 cm, 36 inches
Adapter sets
–– 85130D 3.5 mm1 to 3.5 mm
1. Special rugged female connector specifically for connecting to the network analyzer test port, but does not mate with a standard male connector.
2. For use with E8362C.
33 | Keysight | PNA Family Microwave Network Analyzers - Configurations Guide
For devices with Type-N connectors
Mechanical calibration kits
85054B standard: DC to 18 GHz. Includes:
–– 00909-60011 Type-N (m) fixed lowband load
–– 00909-60012 Type-N (f) fixed lowband load
–– 85054-60025 Type-N (m) short
–– 85054-60026 Type-N (f) short
–– 85054-60027 Type-N (m) open
–– 85054-60028 Type-N (f) open
–– 85054-60031 Type-N (f) to 7mm adapter
–– 85054-60032 Type-N (m) to 7mm adapter
–– 85054-60037 Type-N (f) to Type-N (f) adapter
–– 85054-60038 Type-N (m) to Type-N (m) adapter
–– 85054-80010 Type-N (f) sliding load
–– 85054-80009 Type-N (m) sliding load
–– 85054-60050 Type-N (f) connector gage
–– 85054-60052 Type-N (f) gage master
–– 85054-60051 Type-N (m) connector gage
–– 85054-60053 Type-N (m) gage master
85054D economy: DC to 18 GHz. Includes:
–– 85054-60025 Type-N (m) short
–– 85054-60026 Type-N (f) short
–– 85054-60027 Type-N (m) open
–– 85054-60028 Type-N (f) open
–– 85054-60031 Type-N (f) to 7mm adapter
–– 85054-60032 Type-N (m) to 7mm adapter
–– 85054-60037 Type-N (f) to Type-N (f) adapter
–– 85054-60038 Type-N (m) to Type-N (m) adapter
–– 85054-60046 Type-N (m) fixed load
–– 85054-60047 Type-N (f) fixed load
Adapter sets
–– 85130C 3.5 mm2 to Type-N
Electronic calibration kits
N4431B Microwave ECal: 300 kHz to 13.5 GHz, 4-ports.
Includes:
–– Option 020 module with:
N4431-60007 4 x Type-N (f) ECal module
1. Special rugged female connector specifically for connecting to the
network analyzer test port, but does not mate with a standard male
connector.
2. For use with E8362C.
N4431B-xxx mixed-connector options:
Connector type
Port A
option
Port B
option
Port C
option
Port D
option
3.5 mm (f)
101
201
301
401
3.5 mm (m)
102
202
302
402
Type-N 50 ohm (f)
103
203
303
403
Type-N 50 ohm (m)
104
204
304
404
7-16 (f)
105
205
305
405
7-16 (m)1
106
206
306
406
1
N4432A Microwave ECal: 300 kHz to 18 GHz, 4-ports. Includes:
–– Option 020 module with:
N4432-60003 4 x Type-N (f) ECal module
N4432A-xxx mixed-connector options:
Connector type
Port A
option
Port B
option
Port C
option
Port D
option
3.5 mm (f)
101
201
301
401
3.5 mm (m)
102
202
302
402
Type-N 50 ohm (f)
103
203
303
403
Type-N 50 ohm (m)
104
204
304
404
N4690B Microwave ECal: 300 kHz to 18 GHz, 2-ports.
Includes:
–– Option M0F module with:
N4690-60004 Type-N (f) to Type-N (m) ECal module
–– Option 00M module with:
N4690-60005 Type-N (m) to Type-N (m) ECal module
–– Option 00F module with:
N4690-60006 Type-N (f) to Type-N (f) ECal module
–– Option 00A adds:
85054-60037 Type-N (f) to Type-N (f) adapter
85054-60038 Type-N (m) to Type-N (m) adapter
Cables2
Use the test port cables recommended for devices with 7 mm
connectors, and 7 mm to Type-N adapters that are from the
85054B/D Type-N calibration kit (see 7 mm connector section).
34 | Keysight | PNA Family Microwave Network Analyzers - Configurations Guide
For devices with 7 mm connectors
For devices with waveguide
Mechanical calibration kits
Mechanical calibration kits
85050B standard: DC to 18 GHz. Includes:
–– 00909-60008 7 mm coax termination
–– 85050-60006 7 mm fixed broadband load
–– 85050-80007 7 mm short
–– 85050-80010 7 mm open
–– 85050-80011 7 mm sliding load
X Band
X11644A standard, WR-90: 8.2 to 12.4 GHz. Includes:
–– 00896-60008 X-band standard section
–– 00910-60003 X-band termination
–– 11644-20018 X-band short
–– 11644-20021 X-band shim
–– 85132F cable set (set, flexible 3.5 mm (f) to 7 mm, 62.9 cm
each, 24.75 inches each2)
–– 85135F cable set (set, flexible, 2.4 mm (f) to 7 mm, 53 cm
each, 21 inches each)
–– X281C adapter (included in calibration kit): WR-90 to 7 mm
85050C precision TRL: DC to 18 GHz. Includes:
–– 00909-60008 7 mm coax termination
–– 85050-60003 7 mm to 7 mm airline
–– 85050-60005 7 mm to 7 mm TRL adapter
–– 85050-60006 7 mm fixed broadband load
–– 85050-80008 7 mm short
–– 85050-80009 7 mm short collet
–– 85050-80010 7 mm open
85050D economy: DC to 18 GHz. Includes:
–– 85050-60006 7 mm fixed broadband load
–– 85050-80007 7 mm short
–– 85050-80010 7 mm open
Electronic calibration kits
–– N4696B Microwave ECal: 300 kHz to 18 GHz, 2-ports,
7 mm to 7 mm Microwave module
Cables1
–– 85132E single, flexible: 3.5 mm (f) to 7 mm, 97.2 cm,
38.25 inches2
–– 85132F set, flexible: two 3.5 mm (f) to 7 mm cables, 62.9 cm
each, 24.75 inches each2, p/n 85132-60004
–– 85135E single, flexible: 2.4 mm (f) to 7 mm, 96 cm, 38 inches
–– 85135F set, flexible: two 2.4 mm (f) to 7 mm cables, 53 cm
each, 21 inches each, p/n 85135-60002
Adapter sets
–– 85130E 2.4 mm1 to 7 mm
1. For use with E8362C.
2. Special rugged female connector specifically for connecting to the
network analyzer test port, but does not mate with a standard male
connector.
P Band
P11644A standard, WR-62: 12.4 to 18 GHz. Includes:
–– 00896-60007 P-band standard section
–– 00910-60002 P-band termination
–– 11644-20017 P-band short
–– 11644-20020 P-band shim
–– 85132F cable set (set, flexible, 3.5 mm (f) to 7 mm, 62.9 cm
each, 24.75 inches each2)
–– 85135F cable set (set, flexible, 2.4 mm (f) to 7 mm, 53 cm
each, 21 inches each)
–– P281C adapter (included in calibration kit): WR-62 to 7 mm
K Band
K11644A standard, WR-42: 18 to 26.5 GHz. Includes:
–– 00896-60006 K-band standard section
–– 00910-60001 K-band termination
–– 11644-20016 K-band short
–– 11644-20019 K-band shim
–– 85134F cable set (set, flexible, 2.4 mm (f) to 3.5 mm (f) and
(m), 53 cm each, 21 inches each)
–– K281C adapter (included in calibration kit): WR-42 to 3.5 mm
(f) Option 012 WR-42 to 3.5 mm (m)
R Band
R11644A standard, WR-28: 26.5 to 40 GHz. Includes:
–– 00914-20028 R-band termination
–– 11644-20005 R-band short
–– 11644-20003 R-band shim
–– 11644-60001 R-band 10 cm straight waveguide
–– 11644-60016 R-band 5 cm straight waveguide
–– 85133F cable set (set, flexible, 2.4 mm, 53 cm each,
21 inches each)
–– R281A adapter (2.4 mm (f) to WR-28 waveguide adapter)
–– R281B adapter (2.4 mm (m) to WR-28 waveguide adapter)
35 | Keysight | PNA Family Microwave Network Analyzers - Configurations Guide
Q Band
Q11644A standard, WR-22: 33 to 50 GHz. Includes:
–– 11644-60005 Q-band termination
–– 11644-20004 Q-band short
–– 11644-20001 Q-band shim
–– 11644-60002 Q-band 10 cm straight waveguide
–– 11644-60017 Q-band 5 cm straight waveguide
–– 85133F cable set (set, flexible, 2.4 mm, 53 cm each,
21 inches each)
–– Q281A adapter (2.4 mm (f) to WR-22 waveguide adapter)
–– Q281B adapter (2.4 mm (m) to WR-22 waveguide adapter)
U Band
U11644A standard, WR-19: 40 to 60 GHz. Includes:
–– 11644-60006 U-band termination
–– 11644-20004 U-band short
–– 11644-20002 U-band shim
–– 11644-60003 U-band 10 cm straight waveguide
–– 11644-60018 U-band 5 cm straight waveguide
V Band
V11644A standard, WR-15: 50 to 75 GHz. Includes:
–– 11644-60025 V-band termination
–– 11644-20015 V/W-band short
–– 11644-20013 V-band shim
–– 11644-60012 V-band standard section
W Band
W11644A standard, WR-10: 75 to 110 GHz.Includes:
–– 11643-60026 W-band termination
–– 11644-20015 V/W-band short
–– 11644-20014 W-band shim
–– 11644-60013 W-band standard section
Verification kits
All Keysight verification kits include:
–– precision Z0 airline or match thru
–– mismatched airline or mismatch thru
–– fixed attenuators
–– traceable measured data and uncertainties
85051B 45 MHz to 18 GHz 7 mm kit
Includes attenuators, airline and mismatch airline with data on
a 3.5-inch disk for use in confirming accuracy enhanced system
measurement performance, traceable to national standards. Test
procedure is provided in the service manual.
85053B 300 kHz to 26.5 GHz 3.5 mm kit
Includes attenuators, airline and mismatch airline with data on
a 3.5-inch disk for use in confirming accuracy enhanced system
measurement performance, traceable to national standards. Test
procedure is provided in the service manual.
85055A 300 kHz to 18 GHz Type-N kit
Includes attenuators, airline and mismatch airline with data on
a 3.5-inch disk for use in confirming accuracy enhanced system
measurement performance, traceable to national standards. Test
procedure is provided in the service manual.
85057B 45 MHz to 50 GHz 2.4 mm kit
Includes attenuators, airline and mismatch airline with data on
a 3.5-inch disk for use in confirming accuracy enhanced system
measurement performance, traceable to national standards. Test
procedure is provided in the service manual.
85058V 45 MHz to 67 GHz 1.85 mm kit
Includes attenuators, match thru and mismatch thru with data on
a 3.5-inch disk for use in confirming accuracy enhanced system
measurement performance, traceable to national standards. Test
procedure is provided in the service manual.
General Accessories
Spare drive1
1. For more information on solid-state drive, refer to
na.tm.keysight.com/pna/hdnumbers.html
–– N8981A spare solid-state drive with mounting cradle
For E836xA/B and N5230A.
–– N8982A spare solid-state drive with mounting cradle
For E836xC and N5230C.
–– N8983A spare solid-state drive with mounting cradle
For all PNAs with Windows 7 currently installed
–– N5242-60044 spare solid-state drive with mounting cradle
For N524xA with 2.0 GHz Core 2 Duo CPU.
–– N5242-60088 spare solid-state drive with mounting cradle
For N522xA/4xA with 2.0 GHz Core i7 CPU.
–– N5235-60060 spare solid-state drive with mounting cradle
For N523xA with 1.87 GHz Celeron CPU.
–– Spare solid-state drive for N5242A/1A with 1.6 GHz Pentium
M CPU is discontinued. Upgrading to 2.0 GHz Core i7 CPU
(W1312-60196) is recommended.
36 | Keysight | PNA Family Microwave Network Analyzers - Configurations Guide
General Accessories, continued
Probe
–– 85024A high-frequency probe; provides high-impedance
in-circuit test capability from 300 kHz to 3 GHz.
Power meters and sensors1
Recommended for self support, adjustments and performance
tests to verify proper instrument operation.
–– N1913A EPM power meter (single channel)
–– N1914A EPM power meter (dual channel)
–– N8481A power sensor, 10 MHz to 18 GHz, -35 to +20 dBm
–– N8481B power sensor, 10 MHz to 18 GHz, -5 to +44 dBm
–– N8481H power sensor, 10 MHz to 18 GHz, -15 to +35 dBm
–– N8482A power sensor, 100 kHz to 6 GHz, -35 to +20 dBm
–– N8482B power sensor, 100 kHz to 6 GHz, -5 to +44 dBm
–– N8482H power sensor, 100 kHz to 6 GHz, -15 to +35 dBm
–– N8485A power sensor, 50 MHz to 26.5 GHz, -35 to +20 dBm
–– N8485A-033 average power, 10 MHz to 33 GHz, -35 to
+20 dBm, 3.5 mm (m)
–– N8486AQ waveguide, 33 to 50 GHz, -35 to +20 dBm
–– N8486AR waveguide, 26.5 to 40 GHz, -35 to +20 dBm
–– N8487A power sensor, 50 MHz to 50 GHz, -35 to +20 dBm
–– N8488A power sensor, 10 MHz to 67 GHz, -35 to +20 dBm
–– V8486A waveguide power sensor, 50 to 75 GHz , -30 to
+20 dBm
–– W8486A waveguide power sensor, 75 to 110 GHz , -30 to
+20 dBm
–– U2000A USB sensor, 10 MHz to 18 GHz, -60 to +20 dBm
–– U2000B USB sensor, 10 MHz to 18 GHz, -30 to +44 dBm
–– U2000H USB sensor, 10 MHz to 18 GHz, -50 to +30 dBm
–– U2001A USB sensor, 10 MHz to 6 GHz, -60 to +20 dBm
–– U2001B USB sensor, 10 MHz to 6 GHz, -30 to +44 dBm
–– U2001H USB sensor, 10 MHz to 6 GHz, -50 to +30 dBm
–– U2002A USB sensor, 50 MHz to 24 GHz, -60 to +20 dBm
–– U2002A-H26 USB sensor, 10 MHz to 26.5 GHz, -60 to
+20 dBm
–– U2002H USB sensor, 50 MHz to 24 GHz, -50 to +30 dBm
–– U2004A USB sensor, 9 kHz to 6 GHz, -60 to +20 dBm
–– E4412A CW power sensor, 10 MHz to 18 GHz, -70 to
+20 dBm
–– E4413A CW power sensor, 50 MHz to 26.5 GHz, -70 to
+20 dBm
–– E4413A-H33 specified performance for 50 MHz to 33 GHz
Comb generators
Two are required for NVNA. Also requires separate power supply.
–– U9391C 10 MHz to 26.5 GHz comb generator
–– U9391F 10 MHz to 50 GHz comb generator
–– U9391G 10 MHz to 67 GHz comb generator
Amplifiers
–– 83006A power amplifier, 10 MHz to 26.5 GHz, 20 dB gain,
power out: +18 dBm to 10 GHz or +16 dBm to 20 GHz or
+14 dBm to 26.5 GHz
–– 83017A power amplifier, 50 MHz to 26.5 GHz, 25 dB gain,
power out: +20 dBm to 20 GHz, or +15 dBm to 26.5 GHz
–– 83018A power amplifier, 2 to 26.5 GHz, 27 dB gain to 20 GHz
or 23 dB to 26.5 GHz, power out: +24 dBm to 20 GHz or
+21 dBm to 26.5 GHz
–– 83020A power amplifier, 2 to 26.5 GHz, 30 dB gain to 20 GHz
or 27 dB to 26.5 GHz, power out: +30 dBm to 20 GHz or
+26 dBm to 26.5 GHz
–– 83050A power amplifier, 2 to 50 GHz, 23 dB gain, power out:
+20 dBm to 40 GHz or +17 dBm to 50 GHz
–– 83051A power amplifier, 45 MHz to 50 GHz, 23 dB gain
power out: +12 dBm to 45 GHz or +10 dBm to 50 GHz
Couplers
–– 87300B coaxial coupler, 1 to 20 GHz, SMA (f), 10 dB
coupling
–– 87300C coaxial coupler, 1 to 26.5 GHz, 3.5 mm (f), 10 dB
coupling
–– 87301B coaxial coupler, 10 to 46 GHz, 2.92 mm (f), 10 dB
coupling
–– 87301D coaxial coupler, 1 to 40 GHz, 2.4 mm (f) or optional
2.92 mm (f), 13 dB coupling
–– 87301E coaxial coupler, 2 to 50 GHz, 2.4 mm (f), 10 dB
coupling
–– 87310B 90o coaxial coupler, 1 to 18 GHz, SMA (f), 3 dB
coupling
Equipment rack accessories
–– E3663AC Rail kit (included with Option 1CM and 1CP)
–– CM042A Rack mount kit, for use without handles (included
with Option 1CM)
–– 5063-9224 Rack mount kit with handles2
–– 5063-9230 Front handle kit 2
–– 5063-9237 Rack mount kit, for use with classic handles
(included with Option 1CP)2
Monitors
–– VGA-compatible monitor
Interface cables
Choose the appropriate cables to connect each peripheral to the
network analyzer.
–– 10833A GPIB cable, 1.0 m (3.3 ft)
–– 10833B GPIB cable, 2.0 m (6.6 ft)
–– 10833D GPIB cable, 0.5 m (1.6 ft)
–– 82357B GPIB to USB interface
1. For the latest guide to power meters and power sensors, refer to the Keysight web site: www.keysight.com/find/powermeters
2. 5063-9224 is a complete rack mount kit with handles. N52xxA comes with ruggedized handles, which must be replaced with classic handles
shipped with the kit. 5063-9230 is a pair of classic handles, and used with 5063-9237 for mounting N52xxA to a rack.
37 | Keysight | PNA Family Microwave Network Analyzers - Configurations Guide
www.lxistandard.org
LAN eXtensions for Instruments puts the power of Ethernet and the
Web inside your test systems. Keysight is a founding member of the LXI
consortium.
For more information on Keysight
Technologies’ products, applications or
services, please contact your local Keysight
office. The complete list is available at:
www.keysight.com/find/contactus
Three-Year Warranty
www.keysight.com/find/ThreeYearWarranty
Keysight’s commitment to superior product quality and lower total cost
of ownership. The only test and measurement company with three-year
warranty standard on all instruments, worldwide.
Keysight Assurance Plans
www.keysight.com/find/AssurancePlans
Up to five years of protection and no budgetary surprises to ensure your
instruments are operating to specification so you can rely on accurate
measurements.
www.keysight.com/go/quality
Keysight Technologies, Inc.
DEKRA Certified ISO 9001:2008
Quality Management System
Keysight Infoline
www.keysight.com/find/service
Keysight’s insight to best in class information management. Free access to
your Keysight equipment company reports and e-library.
Keysight Channel Partners
www.keysight.com/find/channelpartners
Get the best of both worlds: Keysight’s measurement expertise and product
breadth, combined with channel partner convenience.
www.keysight.com/find/pna
Americas
Canada
Brazil
Mexico
United States
(877) 894 4414
55 11 3351 7010
001 800 254 2440
(800) 829 4444
Asia Pacific
Australia
China
Hong Kong
India
Japan
Korea
Malaysia
Singapore
Taiwan
Other AP Countries
1 800 629 485
800 810 0189
800 938 693
1 800 11 2626
0120 (421) 345
080 769 0800
1 800 888 848
1 800 375 8100
0800 047 866
(65) 6375 8100
Europe & Middle East
Austria
Belgium
Finland
France
Germany
Ireland
Israel
Italy
Luxembourg
Netherlands
Russia
Spain
Sweden
Switzerland
United Kingdom
0800 001122
0800 58580
0800 523252
0805 980333
0800 6270999
1800 832700
1 809 343051
800 599100
+32 800 58580
0800 0233200
8800 5009286
800 000154
0200 882255
0800 805353
Opt. 1 (DE)
Opt. 2 (FR)
Opt. 3 (IT)
0800 0260637
For other unlisted countries:
www.keysight.com/find/contactus
(BP-04-23-15)
This information is subject to change without notice.
© Keysight Technologies, 2012 - 2015
Published in USA, May 6, 2015
5990-7745EN
www.keysight.com