ECO-500

INSTRUCTION MANUAL

Read all instructions before using this machine.

IMPORTANT SAFETY INSTRUCTIONS

This manual is to ensure that the CFR ECO-500 is operated correctly.

All operators must read, understand and practice the following safety instructions.

ECOMANU 12/2008

CFR ECO-500

TABLE OF CONTENTS

Introduction ............................................................2

Unpacking instructions ........................................2

Safety instructions ................................................2

Preparing for cleaning ..........................................3

Operating instructions ..........................................4

Maintenance ...........................................................4

Parts and drawings ...............................................7

Warranty ...............................................................11

UNPACKING INSTRUCTIONS

Your ECO-500 was thoroughly inspected, tested, and packaged to deliver the equipment in good operating condition. The freight carrier received and signed for the equipment in good condition. Damage can occur during shipping and to protect your interest, all cartons must be inspected for damage (including any concealed damage) that might have occurred during shipment. Any damage is the responsibility of the freight carrier and should be reported immediately to the carrier. It is your responsibility to issue a claim and to receive compensation from the freight carrier for any damage done in transit. Shipping damage is not warranted.

INTRODUCTION

Congratulations on your purchase of a CFR ECO-500.

Read this entire manual before operating or servicing.

Please complete and return the enclosed warranty card.

PARTS AND SERVICE

The ECO-500 is covered by CFR’s Preventative

Maintenance Program which is designed to maintain the

ECO 500 on a quarterly basis. The program focuses on: inspecting the equipment, replacing covered parts as required, and identifying potential situations where a more in-depth service or training may be required.

If service is required, it must be performed by an authorized CFR repair center. Contact your local dealer or call

1.800.533.2557 for the location of a repair center.

SERIAL NUMBER

The serial number of the machine is located on the label, located on the backside of the base. This information is needed when ordering parts or scheduling repairs. Fill in the information below for future reference:

Serial Number

Part Number 10468A CFR ECO-500 115V

(10469A CFR ECO-500-2 230V)

Purchase Date

CAUTION

Read All Instructions, Warnings and

Cautions before Using

These guidelines are provided for your protection and convenience. Please read them carefully. If you have any questions regarding the use of your equipment call CFR

Technical Service at 800.533.2557. Failure to adhere to instructions provided can potentially void any warranties.

Precautions and safety warnings are provided for your protection. Failure to observe these warnings could result in personal injury and damage to the equipment.

When using an electrical appliance, basic safety precautions should always be followed.

WARNING!

To avoid fire, do not use with a flammable or combustible liquid to clean floor.

IMPORTANT SAFETY INSTRUCTIONS

The ECO-500 is intended for use only as described in this manual. Using the equipment in any manner not described in this manual can void the warranty. Use only manufacturer’s recommended accessories.

READ ALL INSTRUCTIONS BEFORE USING

THIS PRODUCT IS INTENDED FOR

COMMERCIAL USE ONLY

2

When using a electrical piece of equipment basic precautions should be followed, including the following:

WARNING! To reduce the risk of electric shock, fire, or injury:

1. Operators must read and understand this manual completely before operating the equipment.

2. Make sure all caution, warning, and instructional decals are in place and legible. Replace damaged or missing labels.

3. Do not leave unit unattended while plugged in. Unplug from outlet when not in use and before servicing.

4. Connect to a proper grounded outlet only. (See

Grounding Instructions.)

5. Do not use with damaged cord or plug.

6. Do not handle plug or unit with wet hands.

7. Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.

8. Turn off all controls before unplugging.

9. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord and remove from outlet.

10. Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air flow.

11. Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

12. Do not use without filters in place.

13. Use extra care when cleaning stairs.

14. Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they may be present.

15. Do not expose to rain. Store indoors.

16. If unit is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, take it to a local CFR service center.

GROUNDING INSTRUCTIONS

This unit must be grounded. Grounding provides the path of least resistance for electric current, in the event of malfunction or breakdown, to reduce the risk of electric shock. This unit is equipped with a cord having an equipment grounding conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.*

ADAPTER

WARNING!

Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the appliance - if it will not fit the outlet; have a grounded outlet installed by a qualified electrician.

SET UP INSTRUCTIONS

Filter Installation

There are three filters in the ECO-500 system: basket filter, bag filter and canister filter. It is imperative to the efficient operation of the ECO-500 that the filters are installed properly.

Bag Filter

Place bag filter in recovery inlet area. Be sure that wire container is in place before fitting bag filter in place.

Basket Filter

Position basket filer over bag filter and attach recovery inlet using the two swivel clamps.

GROUNDING

PIN

( A )

GROUNDED

OUTLET BOX

2

( B )

METAL

SCREW

( C )

TAB FOR

GROUNDING SCREW

* The illustration applies only to 115V model.

3

CAUTION! When cleaning, monitor foam in the machine’s tank. Areas cleaned with other cleaning equipment or chemicals may cause excessive foam to collect in the tank.

Canister Filter

Soak canister filter inside and out in water before installing inside recovery tank. Make sure water is coming through the filter wall when you fill with water while holding the canister upside down. To install, simply screw canister filter into place.

OPERATING INSTRUCTIONS

1. Remove lid and composite filter.

2. Check canister filter. Make sure the canister filter is installed snugly.

3. Fill tank with water to a desired level or 1” below the vacuum float switch. Warm water will be more efficiently heated to desired temperature than cold water.

4. Add CFR in-tank cleaner per chemical label use instructions. In addition, pre-spraying is often desirable and will assist in producing the fastest and best cleaning results. See chemical product labels for more information. Note: Use caution when moving machine

(especially on inclines) with fluid in the tank to prevent fluid from entering vacuum intake at back of machine tank and flooding the vacuum.

CFR chemicals have been specially formulated to

work with this machine.

5. Plug the receptiacle cords into separate circuits.

Green light will turn on when properly connected. 115 model only.

6. Prime pump by re-circulating fluid through priming hose included for 15/30 seconds. Attach priming hose to quick connect and turn pump on while placing opposite end of hose directly back into tank. Once a steady stream of solution flows, you may turn off pump and remove priming hose. The machine is now primed.

Re-circulating the fluid primes the pump and expels trapped air from the system.

7. Replace inlet filter and lid

8. Lock the rectangular lid into position

9. Attach hose assembly to machine, connect fluid hose to the quick-disconnect found on the front of machine and connect vacuum hose cuff to recovery inlet fitting.

10. Attach the desired tool to the valve end of the hose assembly.

11. Turn on vacuum and pump switches.

12. Turn on heater switch if desired.

13. Clean surface with tool attached to hose assembly.

14. During the cleaning process, for any reason, the fluid level is heightened, the high level float switch will shut off the vacuum motors. Should such case happen, drain the tank so the fluid level is much below the high float switch.

WARNING! EXCESSIVE FOAM IN THE TANK

MAY CAUSE VACUUM MOTOR FLOODING

AND MACHINE DAMAGE. Pour one to two ounces of

CFR Defoam directly into the tank or into the vacuum hose while the vacuum is running. CFR Defoamer has been specially formulated to work with this machine.

When finished cleaning, perform the daily maintenance procedure. Be sure that all filters are cleaned thoroughly and replaced in machine. Leave lid off for drying.

100 micron pre-filter

25 micron fine particle filter

40 micron main filter

Connection to vacuum hose

Connection to

“Insider” hose

MAINTENANCE

Daily Maintenance

Vacuum/float shut-off switch

Pump/low solution switch

To maintain optimum performance of the equipment, tools and filters should be cleaned after each use. Replace any filters that cannot be cleaned or are damaged. Nozzles that cannot be cleared should be discarded. Wipe down the equipment with a damp cloth to keep clean and preserve the appearance.

1. Wands and Tools

Rinse opening of tool with water to eliminate any debris.

4

Wand only - open and clean in-line strainer.

A. Disconnect the In-line Strainer by using the quick disconnect coupler.

B. Remove the filter and rinse with water.

C. Remove any debris from the strainer.

D. Keep o-ring and threads of the plug lubricated. CFR

DEFOAM is a good lubricant or use a non-petroleum based lubricant. This will ensure a tighter seal.

Wipe tool with damp cloth and store with head up to prevent clogging of nozzle.

2. Filters

In-Line Strainer Filter - Disconnect the In-line Strainer

Filter on the wand by using the quick disconnect coupler.

Remove the filter and rinse with water. Remove any debris from the strainer. Keep o-ring and threads of the plug lubricated. CFR DeFoam is a good lubricant or use a nonpetroleum based lubricant. This will ensure a tighter seal.

Basket Filter - Remove the basket filter. Dump and clean debris at the end of each cleaning job.

Bag Filter - Remove the bag filter and rinse out and clean thoroughly or replace with part# 72776A.

Canister Filter - Unscrew this filter and rise thoroughly with water. Be sure to rinse both inner and outer filter media. When finished screw cartridge filter back in place.

Periodic Maintenance

1. Check power cord for any breaks, separations, or cuts.

Make sure the ground pin on the connector is intact or the machine will be unsafe. Make sure the ground pin on all three prongs on the twist lock connector are intact.

2. Check for plugged nozzles when using tools. If streaking occurs during cleaning, a plugged nozzle may be the cause. A plugged or partially plugged nozzle can be identified by holding the tool 5-7” above the surface and checking for an even spray pattern. To clean a plugged nozzle, remove the nozzle and direct pressurized air backwards through the nozzle or backwash the nozzle with water. A convenient method is to insert the nozzle into a garden hose ball valve, tighten the ball valve to a faucet, and turn on the water. (CFR has ball valves available, part #7AX020). Inspect nozzle and repeat cleaning procedure, if necessary. Discard nozzles that cannot be cleared. Tool nozzles wear and must be replaced after 200-250 hours of use.

3. Occasionally open the base and inspect hose and other connections for leaks. Repair or replace any leaking parts. Always disconnect power cord, before removing side panels.

Circuit Breakers: Overload circuit breakers are placed in both the pump and vacuum circuits to protect against unusually heavy current (ampere) loads. If either breaker trips, the pump motor or vacuum motor is overloaded.

4. It is very important to monitor machine operating hours for proper maintenance of the motors and pumps. After

700 hours of operation, the vacuum motor brushes should be inspected by an authorized repair station and replaced if worn (length is .5 inches or less).

5

5. Check vacuum motor performance using a vacuum gauge. Place this gauge on the tank inlet fitting with the vacuum turned on. Water lift should be between

190 and 210 inches. If the reading is lower, check for air leaks in the tank, cover gasket, and drain hose.

6. Check pump performance occasionally against built-in pressure gauge. Maximum pump running pressure on the ECO-500 should be 500 ± 10 p.s.i, If the pumping pressure is outside of this range, call your dealer or authorized station. After 400 hours, the pump valves should be replaced. After 700 hours of operation the pump cam bearing and plunger should be replaced.

The pressure regulator should be rebuilt after 400 hours of operation.

SPECIFICATIONS - ECO-500

Power Cord ................................Two Cords, 12 Ga, 3

Wire, Molded End Plug

Voltage_USA .........................115/120 volts AC, 60 HZ

Voltage_UK ..................................230 volts AC, 50 HZ

Tank Volume .......................................10 gallons max

Fill Level .............1” below the high water shutoff float

Vacuum Motor ............. (2) 3 stage with 210” water lift

Pump Motor ...................................... 1/4 hp AC motor

Pump ...............................plunger type; 50 to 500 psi.

Weight ............................................................ 104 lbs.

Height .....................................................................35”

Width ......................................................................20”

Length ....................................................................29”

Wheels ................... (2) 10” non-marking rear wheels

Casters .......... (2) 4” non-marking front swivel casters

Body ...rotomolded polyethelene tank, powder coated aluminum base

Filters .4 filters: 100 mesh basket filter, 25 micron bag filter, 40 micron canister filter and inline filter at wand.

TROUBLE SHOOTING GUARD

Vacuum or pump will not run

• Check that electrical cord is firmly seated in wall outlet.

• Check and reset building circuit breaker if tripped.

Trips building circuit breaker

• Circuit is overloaded - move cord to a different wall outlet.

• If using an additional extension cord, make sure it is in good condition, less than 70 feet long and #12 gauge or

heavier.

• Check plug end and cord for damage.

• Check machine for dual circuit indicator light. If the light is not green, than you must move one cord to a different

outlet on another circuit.

Vacuum won’t run.

• Check vacuum switch. It should be in the “on” position.

• Check that water level in tank is not too high.

Pump won’t run

• Check pump switch - it should be in the “on” position.

• Check pump circuit breaker (5 amp) and reset if tripped.

• Check fluid level, must have at least 5 gallons in tank.

Pump tries to run and then blows circuit breaker

• Check power cord for frayed, cut or worn spots.

• If using an extension cord, make sure it is in good condition, less than 70 feet long and #12 gauge or heavier.

• Check pump static PSI - must be 500 psi or less

• Check wall outlet voltage. If below 105 volts, pump will not work.

Pump starts and stops

• Check for sticking pump float.

• Check fluid level - must have at least 5 gallons in tank.

Pump starts and sprays reduced amount of fluid

• Drain the tank and remove the cartridge filter, thoroughly clean and soak both inner and outer filter media. Replace

the filter and fill the tank. Prime the pump

Water dripping from bottom of machine exhaust

• Check machine for excess foaming. Add CFR Defoam to tool hose and tank. Open machine top cover and let

vacuum run for 10 minutes to dry out vacuum motor, then close lid and resume cleaning.

Vacuum hose or tool leaks

• Leave vacuum running for 1 minute when finished cleaning to clear hose.

• Check for holes/breaks in vacuum hose.

• Make sure the inline strainer is properly tightened and fluid hose connectors are fully seated.

Carpet too wet

• NOTE: CFR Wonder Wands are used in a drag position, different from CFR Roller Wand or Glide Wand.

• Check carpet tool position - head must be completely “seated” on carpet to provide maximum water recovery.

• Check tool and hose for any obstructions.

• Check lid cover sealing properly - is basket filter gasket properly seated in tank? Is basket filter gasket in good

shape with no cuts, cracks, or worn/compressed areas?

• Check for cracks in lid cover.

• Check drain hose and fittings for cracks and tears.

• Check tool hose for holes, cracks, or cuts.

• Check hose cuffs - must seat firmly on tank fitting and tool.

• Check water dripping from bottom of machine exhaust. If present, check machine for excess foaming.

• Check carpet installation. Some carpets are installed on uneven surfaces with ridges and bumps. It is difficult to get

good drying times with this type of installation.

Streaks on carpet

• Check tool and hose for obstructions.

• Check and clean inline strainer filter.

• Check and clean in tank filters.

• Check and clean stainless back flush filter screen inside tank.

• Check nozzles for full spray. Clean if clogged or replace if worn.

• Check pump pressure drop while cleaning. Should not drop more than 100 p.s.i. Make sure air is out of system by

re-priming pump. If there is still a problem, remove and clean canister filter.

• Make sure strokes overlap a minimum of 3 inches.

• Check CFR chemical usage instructions for proper application.

• Multiple cleanings may be needed to clean deeply imbedded dirt that is pulled to the surface by CFR’s deep clean

ing technolo gy. Offset cleaning passes by 6 inches.

Excessive pressure drop when cleaning. (exceeds 100 p.s.i.)

• Adjust static pressure to 500 p.s.i. when not cleaning.

• Check and clean in tank filters.

• Check and replace worn spray nozzles and loose or leaking fittings on hose.

• Purge excess air from pumping system using priming hose or hose with no nozzle.

6

TANK

7

TANK

7

8

5

6

9

3

4

1

2

DESCRIPTION

Tank

Handle

Wheel, 4” Handle

1/4 Washer

Frame, Filter

Filter, Cloth

Filter, Basket

Gasket, Basket

Lid, Tank

14

15

16

17

18

10

11

Holder, Lid

10-32 3/4” Screw

12 Elbow, 1 1/2M 1 1/2H, BLK Nylon

13 Lid, 6”

#8 sheet metal screw

Gasket, Lid

Washer, #10, Split Lock

Gasket 1 1/2

Filter, Final

23

24

25

26

19 Float Switch

20 Elbow, 1 1/2M 1 1/2H, BLK Nylon

21

22

Gasket, Float Switch

Hose, Vacuum

Stud, All Threads

Spacer, Wheel

Acorn Nut, 5/16

Gasket, Final Filter

PART NUMBER

72773A

X9453+

X8025+

X8235+

72775A

72776A

72774A

72778C

72790A

72789A

7BR005

7GR034B

PX103+

72387A

PX103G+

7CL003

PX14A+

72777A

70343A

7GR034B

72794A

72384A

72779A

72486A

72059A

72792A

46

47

48

49

50

42

43

44

45

51

36

37

38

39

32

33

34

35

40

41

27

28

29

30

31

2

2

6

1

1

1

1

2

2

1

1

4

1

QTY

1

1

2

1

1

1

1

1

2

1

1

1

1

DESCRIPTION

Hinge, Tank

1/4-20 3/4” Screw

Float Switch, Vacuum

1/8 Coupling

Nipple, 1/8” x 6” Long

Gasket, Float Switch

1/8 Anchor Connector

Gasket, Bulkhead

Barb, 1/4M 1/2H

Bulkhead, Filter

1/4-20 1/2” Screw

Bracket, Tank Lock

Elbow, 1 1/4M 1 1/4H, Nylon

Barb, Elbow, 1/4M 1/8H

1/4 Anchor Connector

1/4 Street Elbow

Gasket 1/1/4

1 1/4” nut

1 1/4” Worm Gear

Drain Hose

Plug, Drain Hose

10-32 3/8

Clip spring

Gasket 1 1/2

1 1/2” nut

2

1

1

1

1

1

1

1

1

6

2

2

1

2

1

1

2

1

2

1

QTY

1

3

1

1

1

PART NUMBER

72768A

7EW001

70343A

7DA001

72799A

72794A

7AJ004

72793A

7AT004

72791A

7BS003

72767A

7GR016

7AT006

PX48+

PC49+

X9164+

X9165+

7DL005

72797A

PAS36+

7BH004

72173A

PX14A+

PX46+

8

115V MODEL

9

115V MODEL

1 Base

DESCRIPTION

2 “Foam, Side Acoustic R”

3 “Cover, Right Side”

4 “10-32 1/2”” Black PHMS”

5 Axle

6 “Spacer, Wheel Axle”

7 “Wheel, 10”

8 “1/4-20 3/4”” Screw”

9 “Bracket, Axle”

10 Caster

11 “Spacer, Caster”

12 Vacuum Chamber Gasket

13 10-32 keps nut

14 Vacuum manifold

15 “10-32 3/4”” Screw”

16 1/4 Washer

17 5/16 keps nut

18 “ 5/16 1 1/4”” Screw”

19 “Bumper, Front”

20 “10-24 1/2”” Screw”

21 “Bracket, QD Coupler”

22 Coupler QD SS

23 “Plug, Bumper”

24 “5/16-18 3/4”””

25 “Regulator, Pressure”

26 “Sleeve, Regulator”

27 Bracket Mount Pressure Regulator

28 1/4” Tee Union

29 “6-32 3/4”” Screw”

30 6-32 nut

31 Pressure Gauge

32 10-24 keps nut

33 1/4 elbow

34 Nut, Push 1/2”

7BR005

X8235+

7BF005

X8227+

72810A

7BS001

71312A

72800A

72804A

7DT001

72059A

72808A

70223A

7AV001

X8243+

X8240+

70066A

7BF003

PC49+

7GL002

PART NUMBER QTY

72781B 1

72796A

72788A

72807A

1

1

8

72769A

72801A

X9063+

7EW001

72770A

71474A

72783A

X9468+

7BF008

X9467+

2

4

3

2

12

2

2

6

1

2

1

1

1

4

8

8

12

8

2

3

1

4

2

3

1

2

1

3

1

1

DESCRIPTION

35 “Cover, Left Side”

36 “Foam, Side Acoustic L”

37 1/4-20 Keps nut

38 1/4 Washer

39 Vacuum Gasket

40 Spacer, Vac, 3.5” L

41 Vacuum 3 Stage 115V

42 “1/4-20 4 1/2”” Hex”

43 Perfect Heat Coil 3 Stage

44 J-Hook 3 stage

45 “#8-32 2 1/2”” screw”

46 “Grill, Fan”

47 Cooling Fan 115V

48 MOTOR 115V Low Profile

49 8-32 keps nut

50 “1/4-20 1/2”” Screw”

51 Heater 2000W

52 1/4-20 Keps nut

53 Motor Mount

54 “Box, Switch”

55 “10-24 1/2”” Screw”

56 “1/4-20 3/4”” Screw”

57 Circuit Breaker 5 amp

58 Hour Meter 115V

59 Rocker Switch

60 Relay 115V

61 Dual Circuit Light

62 Heater Lamp

63 “6-32 3/4”” Screw”

64 “Receptacle, Male Flanged”

65 “Brace, Base”

66 1/4-20 Keps nut

67 “Access Panel, Base”

68 “#8-32 2 1/2”” screw”

7BS003

X9105+

7BF004

72149A

72772A

7BS001

7EW001

X9324+

72411A

PX87+

71379A

PX86+

X8102+

X8243+

X9429+

72795A

7BF004

72809A

X8274+

PART NUMBER QTY

72787A 1

72796B

7BF004

1

4

X8235+

70020B

8

2

72605A

72365A

72812A

72713B

X9423+

X8274+

72702A

72700A

PT400MS+

X8256+

1

1

4

4

1

4

4

2

4

2

4

1

1

4

8

4

4

1

1

4

2

1

4

1

4

4

2

1

1

10

230V MODEL

11

230V MODEL

28

29

30

31

32

33

34

35

36

37

19

20

21

22

23

24

25

26

27

15

16

17

18

11

12

13

14

9

10

7

8

3

4

5

6

1

2

DESCRIPTION

Base

“Foam, Side Acoustic R”

“Cover, Right Side”

“10-32 1/2”” Black PHMS”

Axle

“Spacer, Wheel Axle”

“Wheel, 10”””

“1/4-20 3/4”” Screw”

“Bracket, Axle”

Caster

“Spacer, Caster”

Vacuum Chamber Gasket

10-32 keps nut

Vacuum manifold

“10-32 3/4”” Screw”

1/4 Washer

5/16 keps nut

“ 5/16 1 1/4”” Screw”

“Bumper, Front”

“10-24 1/2”” Screw”

“Bracket, QD Coupler”

Coupler QD SS

“Plug, Bumper”

“5/16-18 3/4”””

“Regulator, Pressure”

“Sleeve, Regulator”

Bracket Mount Pressure Regulator

1/4 Tee Union

“6-32 3/4”” Screw”

6-32 nut

Pressure Gauge

10-24 keps nut

1/4 elbow

“Nut, Push 1/2”””

“Cover, Left Side”

“Foam, Side Acoustic L”

1/4-20 Keps nut

7AV001

X8243+

X8240+

70066A

7BF003

PC49+

7GL002

72787A

72796B

7BF004

7BR005

X8235+

7BF005

X8227+

72810A

7BS001

71312A

72800A

72804A

7DT001

72059A

72808A

70223A

PART NUMBER QTY

72781A 1

72796A

72788A

1

1

72807A

72769A

72801A

8

1

2

X9063+

7EW001

72770A

71474A

72783A

X9468+

7BF008

X9467+

2

4

12

2

3

2

2

6

3

1

4

1

3

1

1

2

2

4

1

1

2

1

4

8

8

12

8

1

1

3

1

64

65

66

67

60

61

62

63

68

69

70

71

51

52

53

54

47

48

49

50

55

56

57

58

59

43

44

45

46

37

38

39

40

41

42

DESCRIPTION

1/4-20 Keps nut

1/4 Washer

Vacuum Gasket

Spacer, vac, 3.5” L

Vacuum 3 Stage 230V

“1/4-20 4 1/2”” Hex”

Perfect Heat Coil 3 Stage

J-Hook 3 stage

“#8-32 2 1/2”” screw”

“Grill, Fan”

Cooling Fan 230V

MOTOR 230V Low Profile

8-32 keps nut

“1/4-20 1/2”” Screw”

Heater 230V 3000W

1/4-20 Keps nut

Motor Mount

“Box, Switch”

“10-24 1/2”” Screw”

“1/4-20 3/4”” Screw”

Circuit Breaker 5 amp

Hour Meter 230V

Relay 230V

Rocker Switch

“10-24 3/4”” Black screw”

10-24 keps nut

Heater Light Red 230V

“6-32 3/4”” Screw”

“Plug, Black”

“Cover, Receptacle”

“Receptacle, Male Flanged”

“Brace, Base”

1/4-20 Keps nut

“Access Panel, Base”

“#8-32 2 1/2”” screw”

PX87+

X8276+

7BF003

72806A

X8243+

71804A+

X9096+

X9000+

72795A

7BF004

72809A

X8274+

PART NUMBER QTY

7BF004 4

X8235+

70020B

8

2

72605A

72611A-C

72812A

4

2

4

72713B

X9423+

X8274+

72702A

72701A

PT400MS-2+

X8256+

7BS003

1

1

4

4

4

1

2

4

PF3000B+

7BF004

72149A

72772A

7BS001

7EW001

X9324+

72410A

71379B

1

1

2

4

4

4

1

1

8

4

1

2

2

12

13

4

4

1

4

1

4

12

Warranty

CFR, a Tacony company, warrants new products manufactured and sold under the name CFR to be free from defects in materials and workmanship under normal use and service. CFR’s obligation under this warranty is limited to repairing or replacing, at our option, such products or parts which are returned to our factory authorized service center, freight prepaid, within the warranty period and are found to be defective in materials or workmanship. For rotationally molded polyethylene housings and aluminum frames and chassis this warranty expires 60 months from the date of registration; if the warrant is not registered, it expires 60 months from the factory shipment date. For all other components, with the exception of wear items (i.e. filter, nozzles, etc.) this warranty expires 12 months from the date of registration on the warranty. If not registered, is expires 12 months from the factory shipment date. For hoses, tools, and other attachments manufactured and sold by CFR, this warranty expires 12 months form factory shipment date. Parts replaced or repaired under warranty are guaranteed for the remainder of the original warranty period. Replacement parts that have become defective through wear or abuse are not included in this warranty. CFR will pay service labor to the distributor or authorized service repair center per the warranty flat rate schedule. Service labor will be paid for two years on all warranted polyethylene housings, aluminum frames and chassis, and one year on all other warranted components.

CFR systems are designed for use only with specially formulated CFR Recyclable Cleaning Chemicals. Use of any other chemical in CFR systems may cause damage to the pump, motor and other components and may void the warranty.

This warranty shall cease to be in effect if repairs, replacements or alternations are made by the purchaser or any nonauthorized service station. This warranty does not apply to damage caused by misuse, abuse, or negligence of the buyer or third party, or damage due to transportation of product.

CFR MAKES NO WARRANTY, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATIONS, ANY WARRANTIES

OF FITNESS OR MERCHANTABILITY, EXCEPT AS EXPRESSLY SET FORTH ABOVE WITH RESPECT TO

SUCH PRODUCTS OR PARTS THEREIN. NOR SHALL CFR HAVE INCURRED ANY OTHER OBLIGATIONS OR

LIABILITIES ON ITS PART OR BE LIABLE FOR ANY ANTICIPATED OR LOST PROFITS, INCIDENTAL DAMAGES,

CONSEQUENTIAL DAMAGES, TIME CHARGES OR ANY OTHER LOSSES INCURRED IN CONNECTION WITH THE

PURCHASE,

INSTALLATION, REPLACEMENT OR REPAIR OF SUCH PRODUCTS OR ANY PARTS THEREIN WHETHER

ORIGINAL EQUIPMENT OR INSTALLED AS A REPLACEMENT, COVERED BY THIS WARRANTY OR OTHERWISE;

AND CFR DOES NOT AUTHORIZE ANY PERSONA TO ASSUME FOR CFR ANY OTHER LIABILITY IN CONNECTION

WITH THE PRODUCTS OR PARTS THEREIN.

For more information about top quality CFR products please see your local CFR distributor or visit us at www.

CFRcorp.com

Thank you for purchasing

CFR Cleaning Systems.

3101 Wichita Court - Fort Worth, TX 76140 - 800.533.2557 - www.CFRcorp.com

ECOMANU 12/2008