Audiovox PVS69701 Owner's manual

Audiovox PVS69701 Owner's manual
PVS69701
7" Dual Screen Mobile DVD System
OWNER’S MANUAL
SAFETY PRECAUTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS
RISQUE DE CHOC ELECTRIQUENE PAS OUVRIR
The lightning flash with an
arrowhead symbol, within the
equilateral triangle, is intended to
alert the user to the presence of
uninsulated "dangerous voltage"
within the product's enclosure that may be of
sufficient magnitude to cause an electric shock.
The exclamation point within the
equilateral triangle is intended to
alert the user to the presence of
important operating and
maintenance
(servicing)
instructions in this owner's manual.
CLASS 1 LASER PRODUCT
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO
NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
DO NOT PLACE OBJECTS FILLED WITH LIQUIDS ON OR
NEAR THIS UNIT.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE
OF PLUG TO WIDE SLOT OF POWER OUTLET, THEN FULLY INSERT.
DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED.
REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE.
* SEE REAR OF UNIT FOR GRAPHIC SYMBOLS *
CAUTION
INVISIBLE LASER RADIATION
WHEN OPEN AND INTERLOCKS
DEFEATED.
AVOID EXPOSURE TO BEAM.
This product contains a
low power laser device.
The symbol for Class II
(Double Insulation)
On Placement
• Do not use the unit in places that are extremely hot, • When you are not going to use the unit for a long
time, disconnect the power adapter.
cold, dusty, or humid.
• Do not restrict the air flow of the unit by placing it in a On Condensation
place with poor air flow, by covering it with a cloth, or
• When left in a heated room where it is warm and
by placing it on carpeting.
damp, water droplets or condensation may form
FCC Information
inside the unit. When there is condensation inside
the unit, the unit may not function normally. Let the
WARNING: Changes or modifications to this unit not
unit stand for 1 to 2 hours before turning the power
expressly approved by the party responsible for compliance
on, or gradually heat the room and let the unit dry
could void the user authority to operate the equipment.
before use.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant Rating Plate Location
to Part 15 of the FCC Rules. These limits are designed to • The rating plate location is on the rear of unit.
provide reasonable protection against harmful interference
in a residential installation. This equipment, used in
WARNING: Should any trouble occur,
accordance with the instructions, may cause harmful
disconnect the AC power cord and refer
interference to radio communications.
servicing to a qualified technician.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does Notes on Copyright
cause harmful interference to radio or television reception, It is forbidden by law to copy, broadcast, show, broadcast
which can be determined by turning the equipment off and on cable, play in public, or rent copyrighted material
on, the user is encouraged to try to correct the interference without permission.
by one or more of the following measures:
Apparatus Claims of U.S. Patent Nos. 4,631,603;
4,577,216; 4,819,098 and 4,907,093 licensed for limited
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and viewing uses only.
receiver.
DVD video discs are copy protected, and any recordings
• Connect the equipment into an outlet on a circuit made from these discs will be distorted. This product
different from that to which the receiver is connected. incorporates copyright protection technology that is
• Consult the dealer or an experienced radio/TV protected by method claims of certain U.S. patents and
technician for help.
other intellectual property rights owned by Macrovision
Shielded cables must be used with this unit to ensure Corporation and other rights owners. Use of this copyright
compliance with the Class FCC limits.
protection technology must be authorized by Macrovision
Corporation, and is intended for home and other limited
On Safety
viewing uses only, unless otherwise authorized by
• When connecting or disconnecting the AC cord, grip Macrovision Corporation. Reverse engineering or
the plug and not the cord itself. Pulling the cord may disassembly is prohibited.
damage it and create a hazard.
GB - 1
IMPORTANT SAFETY INSTRUCTIONS
1.
Read Instructions - All the safety and operating instructions should be read before the appliance is
operated.
2.
3.
Retain Instructions - The safety and operating instructions should be retained for future reference.
Heed Warnings - All warnings on the appliance and in the operating instructions should be adhered to.
4.
Follow Instructions - All operating and use instructions should be followed.
5.
Water and Moisture - The appliance should not be used near water - for example, near a bathtub,
washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, and the like.
6.
Carts and Stands - The appliance should be used only with a cart or stand that is recommended by the
manufacturer.
6A. An appliance and cart combination should be moved with care. Quick stops, excessive force,
and uneven surfaces may cause the appliance and cart combination to overturn.
7.
Wall or Ceiling Mounting - The appliance should be mounted to a wall or ceiling only as
recommended by the manufacturer.
8.
Ventilation - The appliance should be situated so that its location or position does not
interfere with its proper ventilation. For example, the appliance should not be situated on a bed, sofa, rug,
or similar surface that may block the ventilation openings; or, placed in a built-in installation, such as a book
case or cabinet, that may impede the flow of air through the ventilation openings.
9.
Heat - The appliance should be situated away from heat sources such as radiators, heat registers, stoves,
or other appliances (including amplifiers) that produce heat.
10. Power Sources - The appliance should be connected to a power supply only of the type described in the
operating instructions or as marked on the appliance.
11. Grounding or Polarization - Precautions should be taken so that the grounding or polarization means of
an appliance are not defeated.
12. Power-Cord Protection - Power-supply cords should be routed so that they are not likely to be walked
on or pinched by items placed upon or against them, paying particular attention to cords at plugs,
convenience receptacles, and the point where they exit from the appliance.
13. Cleaning - The appliance should be cleaned only as recommended by the manufacturer.
14. Nonuse Periods - The power cord of the appliance should be unplugged from the outlet when left unused
for a long time.
15. Object and Liquid Entry - Care should be taken so that objects do not fall, and liquids are not spilled, into
the enclosure through openings.
16. Damage Requiring Service - The appliance should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged; or
B. Objects have fallen, or liquid has been spilled, into the appliance; or
C. The appliance has been exposed to rain; or
D. The appliance does not appear to operate normally or exhibits a marked change in performance; or
E. The appliance has been dropped or the enclosure damaged.
17. Servicing - The user should not attempt to service the appliance beyond that described in the operating
instructions. All other servicing should be referred to qualified service personnel.
GB - 2
TABLE OF CONTENTS
Safety Precautions ........................... 1
Table of Contents ............................. 3
Disc Formats .................................... 4
Accessories ...................................... 5
Remote Control ................................ 5
Control Reference Guide .............. 6-8
Screen Viewing Angle
Adjustment ........................................ 9
Power Supply ................................... 9
Special Functions ........................... 16
Display Function ......................................... 16
Locating a Specific Title .............................. 16
Locating a Specific Chapter/Track .............. 16
Locating a Specific Time ............................. 16
CD / DVD Programmable Memory . 17
DVD Programmable Memory ...................... 17
CD Programmable Memory ........................ 17
Repeat Playback ............................. 17
Connections ............................... 10-12
Repeating a Title/Chapter (DVD) ................ 17
Repeating a Single Track/Whole Disc (CD) 17
Repeating a Specific Section (DVD) ........... 17
Connecting the Monitors ............................. 10
Using Headphones/Earphones ................... 10
Using this Unit with Other Equipment .... 11-12
Playing a Picture File Disc ............. 18
Customizing the Function
Settings ...................................... 19-20
Unit Operation ................................ 13
Sound System ................................ 13
Playing a Disc ............................ 14-15
LANGUAGE Setup ..................................... 19
VIDEO Setup .............................................. 19
SYSTEM Setup .......................................... 19
Using the Car Plug Adapter .......................... 9
Language Code List ....................... 21
Maintenance .................................... 22
Playing a Disc ............................................. 14
Pausing Playback (Still Mode) .................... 14
Stopping Playback ..................................... 14
Skipping to a Different Track ...................... 14
Fast Forward/Fast Reverse ........................ 14
Skip (Forward/Reverse) .............................. 15
Audio Selection ........................................... 15
Subtitle Selection ........................................ 15
Angle Selection ........................................... 15
Cleaning Disc ............................................. 22
Cleaning the Unit ........................................ 22
Important Note ............................................ 22
Installation Guide ........................... 22
Trouble Shooting Guide ................ 23
GB - 3
DISC FORMATS
The unit can playback discs bearing any of the following marks:
DVDs
[8cm / 12cm disc]
Audio CDs
[8cm / 12cm disc]
Region Management Information
Region Management Information: This unit is designed and manufactured to respond to the Region Management
Information that is encoded on DVD discs. If the Region number printed on the DVD disc does not correspond
to the Region number of this unit, this unit cannot play that disc.
The region number of this unit is 1.
Disc Function or Operation that is Not Available
When the
symbol appears on the TV screen, it indicates that the function or operation attempted is not
available at that time. This occurs because the DVD disc manufacturer determines the specific functions.
Certain functions may not be available on some discs. Be sure to read the documentation provided with the disc.
Icons Used on DVDs
Sample lcons
Language selections for audio
Language selections for subtitles
Screen aspect ratio
Multiple camera angles
1
Region code indicator
NOTE:
• When playing back a CD-G (Graphics) or CD EXTRA disc, the audio portion will be played, but the graphic
images will not be shown.
Title, Chapter and Tracks
• DVDs are divided into “titles” and “chapters”. If the
disc has more than one movie on it, each movie would
be a separate “title”. “Chapters” are sections of titles.
• Audio CDs are divided into “tracks”. A “track” is
usually one song on an audio CD.
NOTE:
• Numbers identify each title, chapter, and track on a disc. Most discs have these numbers recorded on them,
but some do not.
Note on Unauthorized Discs
You may not be able to play back some DVD discs on this unit if they were purchased from outside your
geographic area or made for business purposes.
GB - 4
ACCESSORIES
Please check and identify the supplied accessories.
• To order accessories contact web site (http://www.1800customersupport.com)
Remote Control (with battery) ................................................................................... x 1
Car Power Adapter ..................................................................................................... x 1
Strap ............................................................................................................................ x 2
DC Line Cord .............................................................................................................. x 1
Audio/Video Cable ...................................................................................................... x 1
DVD Disc .................................................................................................................... x 1
REMOTE CONTROL
Using the Remote Control
Remove the protective plastic tab before
operating the Remote Control.
• Point the Remote Control at the REMOTE SENSOR
located on the unit.
• When there is a strong ambient light source, the
performance of the infrared REMOTE SENSOR may
be degraded, causing unreliable operation.
• The recommended effective distance for remote
operation is approximately 16 feet (5 meters).
To Change Remote Battery
1. Open the battery door.
2.
Insert one CR2025 (3V) size battery.
BATTERY REPLACEMENT
When the battery becomes weak, the operating distance of the Remote Control is greatly reduced. You will need
to replace the battery.
NOTE:
• If the Remote Control is not going to be used for a long time, remove the battery to avoid corrosion damage
caused by battery leakage.
WARNING: Do not dispose of batteries in a fire.
Batteries may leak or explode.
GB - 5
CONTROL REFERENCE GUIDE
Remote Control
1) TV MODE Button
When the STOP button has been pressed, this
feature allows you to select the screen format. Pan
Scan, Letter Box or Wide-screen will be toggled by
pressing this button once.
2)
PREV Button
Move back through titles, chapters or tracks on a
disc.
3) GOTO Button
Skip directly to a location on a DVD.
4) Cursor ( , , , ) Buttons
Use to highlight selections on a menu screen and
adjust certain settings.
ENTER Button
Confirms selection on a menu screen.
5) MEMORY Button
In stop mode, enter the number of a selected chapter
or track.
6) Number (0 - 9) Buttons
Use when creating programs and entering a parental
level password. Also use to select a CD track
directly.
7) SETUP Button
In stop mode, open and close the SETUP menu.
REPEAT A-B / DISC Button
Perform point-to-point repeat playback on a DVD or
CD.
Repeat chapter or title of a DVD.
Repeat single track or whole CD.
8) MENU Button
Open and close DVD menu.
9)
10)
11)
12)
13)
14)
15)
GB - 6
/
SEARCH Buttons
SEARCH: Fast reverse playback.
SEARCH: Fast forward playback.
NEXT Button
Move forward through titles, chapters or tracks on
a disc.
STOP Button
Stop playing a disc.
PLAY Button
Press to start or resume playback of a disc.
PAUSE Button
Pause playback, frame advance.
DISPLAY Button
Change disc status information displayed on the
screen.
ANGLE Button
Switches between multiple camera angles when the
DVD you are viewing has multiple camera angles
recorded.
AUDIO Button
Select one of the audio sound tracks programmed
on a DVD or select the audio output mode on an
audio CD.
SUBTITLE / RETURN Button
Select one of the subtitle languages programmed
on a DVD.
Return to normal operation after using the SETUP
menu of a DVD.
CONTROL REFERENCE GUIDE
Unit
1)
2)
3)
4)
5)
6)
7)
8)
9)
OPEN Knob
Open the door.
VOLUME Control
Adjust the volume.
AV IN / DVD Switch
Select between the DVD player and an external
video source.
Headphones Jack
VIDEO & AUDIO IN / OUT Jacks
COLOR Button
Adjust for color intensity.
BRIGHTNESS Button
Adjust the relative lightness or darkness of the
color.
SCREEN Switch
WIDE: Wide screen
NORMAL: Pan screen
Remote Sensor
Receives the remote control unit signals.
10)
11)
12)
13)
14)
15)
16)
17)
18)
GB - 7
PREV Button
PREV button to go back to previous
Press
chapters/tracks. Four speeds are available.
NEXT Button
Press
NEXT button to advance to chapters /
tracks. Four speeds are available.
POWER ON / OFF Switch
DC IN (9-12V) Jack
STOP Button
Stop playing a disc.
PAUSE Button
Press to pause playback of disc. Each time you
press the PAUSE button the picture advances one
frame. Press the PLAY button to resume normal
playback.
PLAY Button
Press to start or resume normal playback of a disc.
POWER ON Indicator
When the POWER ON/OFF is switched to the ON
position, the light will illuminate.
Strap
CONTROL REFERENCE GUIDE
Monitor
1)
2)
3)
4)
5)
6)
DC IN 9-12V Jack
DC OUT Jack
Connect to the main unit using the DC LINE
CORD.
MONITOR ON/OFF Switch
MONITOR ON/OFF Indicator
VIDEO IN / AUDIO IN Jacks
Headphones Jack
7)
BRIGHTNESS Control
Adjust the relative lightness or darkness of the
color.
8) COLOR Control
Adjust for color intensity.
9) SCREEN Switch
Wide: Wide screen
Normal: Pan screen
10) VOLUME Control
Adjust the volume.
Installation of Unit / Monitors in Vehicle
• Use the supplied mounting straps when installing the unit/monitor on the back of the vehicle's headrest.
Mounting
Strap
Elastic
Safety Band
1) Loop the safety band
around the headrest.
2) Tightly wrap the mounting
strap around the headrest.
SAFETY WARNING!
• This unit should never be used by the vehicle's driver or left unsecured in the vehicle while driving.
• If this unit is being used in your vehicle, be sure that it is secured or held safely, and does not obstruct
any safety device, including air bags or seat belts.
• All passengers should wear seat belts when using this unit in a moving vehicle.
• If in doubt, please contact your vehicle manufacturer for further advice.
GB - 8
SCREEN VIEWING ANGLE ADJUSTMENT
The monitor is designed to allow users to have a comfortable
viewing angle. The viewing angle can be adjusted.
• DVD player can be adjusted approximately +4° / -8°;
• Monitor can be adjusted approximately +/- 9°.
• Gently push the top or bottom of the screen frame to
adjust the viewing angle.
Caution:
• Do not force the screen frame over its maximum viewing
angle settings as stated above. Attempting this will
result in damage to the unit.
POWER SUPPLY
A. Using the Car Plug Adapter
The included 12V car plug adapter is designed for use with vehicles that have a 12V, negative ground
electrical system.
WARNING:
Disconnect the car power
adapter when not in use. Not for
use in 24V vehicles.
•
•
•
•
•
•
Cautions:
• Use this unit only with the included 12V car plug adapter. Use with other car adapters could damage
the unit, or even your vehicle.
The included 12V car plug adapter is for use with this unit only. Do not use it with any other equipment.
In the interest of traffic safety, drivers should not operate the unit or view videos while driving.
When the inside of the 12V car socket is dirty with ashes or dust, the plug section may become hot due to poor
contact. Be sure to clean the 12V car socket before use.
After use, disconnect the 12V car plug adapter from both the unit and 12V car socket.
If the unit is not properly attached to a vehicle, it may become airborne in the event of an accident and cause
damage, injury, or death.
Check your local traffic laws for rules governing the use of video devices in vehicles.
GB - 9
CONNECTIONS
Using this Unit with Other Equipment
A. Connecting Game Systems/Video Equipment
You can connect game systems or other video equipment for playback through the monitors.
Watching Video Equipment
1. Turn on the unit; slide the AV IN / DVD
switch to "AV IN".
2. Turn on the video equipment and follow
the instructions provided with it to
playback.
NOTE:
If you have a mono VCR, the volume level
from the speakers will be low.
(included)
B. Connecting the Unit to a TV
This DVD player can be used with a TV that has A/V inputs. If your TV does not have A/V inputs, you can purchase
an RF modulator (sold separately) to connect the DVD player.
Watching a DVD on your TV
1. Turn on the unit; slide the AV IN / DVD switch to "DVD".
2. Turn on the TV and follow the instructions provided with
it to play the DVD.
NOTE: Make sure you use the correct Audio/Video cable.
(included)
(continued on next page)
GB - 10
CONNECTIONS
C. Connecting a Stereo Receiver or Amplifier
This unit can play two channels Dolby Digital.
Listening to Another Audio Equipment
1. Turn on the unit.
2. Turn on your audio equipment and follow
the instructions provided with it to select
the AUDIO IN function.
NOTE:
• You may experience some interference if
the radio tuner function is selected while
the television is working.
• Make sure to use the correct audio/video
cable. Connecting the plugs incorrectly
(included)
may cause a weak signal.
• If you have a stereo VCR, make sure you set it to stereo mode.
• Due to copyright protection, DVD movies cannot be copied. If you copy a DVD movie onto a videotape, the
resulting copy will be unclear, with poor sound quality. This is NOT caused by a defective DVD system.
Using this Monitor with Other Equipment
You can view a DVD in the main unit, while utilizing a game console or other video equipment on the second monitor
at the same time.
EXAMPLE OF CONNECTION
(included)
GB - 11
CONNECTIONS
Using Headphones/Earphones
• Turn down the volume before connecting the
headphones/earphones. Slowly raise the volume
with the headphones/earphones on until you reach
your desired volume.
NOTE:
When headphones are connected, the speakers are
automatically disabled.
Headphones/
Earphones
(3.5mm diameter plug)
Caution:
• Avoid listening to sound at excessive
levels which could be harmful to your
ears.
Headphones/
Earphones
(3.5mm diameter plug)
UNIT OPERATION
Turning the Unit On
1. Slide the POWER ON/OFF switch on the main unit & MONITOR ON/OFF switch
on the monitor to the 'ON' position.
2. If you select DVD, the DVD logo (start-up picture) will appear on the screen.
SOUND SYSTEM
Dolby Digital (for DVD)
Dolby Digital is a sound system developed by Dolby Laboratories Inc. that gives movie theatre ambience to
audio output when the unit is connected to a Dolby Digital 5.1 channel processor or amplifier.
This unit automatically recognizes DVDs that have been recorded with Dolby Digital.
Not all Dolby Digital sources are recorded with 6 channels.
Some sources marked Dolby Digital may be recorded in Dolby Surround, a 2 channel system. Look for this logo
Manufactured under license from Dolby Laboratories.
'Dolby' and the double-D
symbol are trademarks of Dolby Laboratories.
GB - 12
COMPACT DISC OPERATION
1.Open the disc door
Push and hold the OPEN knob to open
the disc door.
2.Hold the disc by its sides and carefully
place it onto the spindle with the label
side facing up; push gently until you hear
a "click".
3.Close the disc door.
It takes a short while for your unit to load
the disc. After loading, the unit will
automatically start playing the disc.
4.Press the
PLAY button.
GB - 13
PLAYING A DISC
Basic playback
This owner’s manual explains the basic instructions of this unit. Some DVD discs are produced
in a manner that allows specific or limited operation during playback. Such as, the unit may
not respond to all operating commands. This is not a defect in the unit. Refer to the instruction
notes of discs.
“
” may appear on the screen during operation. A “
” means that the desired operation
is not permitted by the unit or disc.
Playing a Disc
1. Slide the POWER ON/OFF switch on the right side of the unit to the 'ON' position.
See CUSTOMIZING THE FUNCTION SETTINGS (page 20) before proceeding to step 2.
2. Open the disc door.
3. Hold the disc by its sides and carefully place it onto the spindle with the label side facing up, pushing gently until
you hear a “click”.
4. Close the disc door.
It takes a short while for your unit to load the disc. After loading, the unit will automatically bring you to the
main menu of the DVD or start playing the DVD.
5. If the unit does not automatically start playing the DVD, press the
PLAY button from the main menu.
Pausing Playback (Still Mode)
Press the
PAUSE button. To resume normal playback, press the
Each time you press the
PLAY button.
PAUSE button, the picture advances one frame.
Stopping Playback
Press the STOP button at the location where you want to interrupt playback. To resume playback at the position
where the disc was stopped, press the PLAY button.
If you press the STOP button twice, the unit’s memory will be cleared and pressing the
the disc to the beginning.
PLAY button will reset
To Skip to a Different Track
• Press the
PREV button repeatedly to skip to the start of the current or previous track.
• Press the
NEXT button to skip to the next track.
• For an audio CD disc, use the number buttons (remote control only) to jump directly to that track number.
Fast Forward/Fast Reverse
1. Press the SEARCH
or
SEARCH button when a disc is playing.
• The disc begins fast scan at x2 speed.
• Four speeds are available. Each time SEARCH
or
SEARCH button is pressed, the speed of fast scan
changes in the following sequence:
2. Press the
PLAY button when you reach the desired point to resume playback at normal speed.
(continued on next page)
GB - 14
Basic playback
PLAYING A DISC
SKIP (Forward / Reverse)
While you are playing a disc, press the
NEXT button to move to the beginning of the next chapter or track. Press
the
PREV button to move to the previous chapter or track. Playback will automatically begin.
Audio Selection
On some discs, the sound is recorded in two or more formats. Follow the directions below to select the type of playback.
1. While a disc is playing, press the AUDIO button to show the current audio format number.
2. Press the AUDIO button repeatedly to select the desired audio format.
NOTE :
• If only one audio format is recorded, the number does not change.
• Approximately two seconds later, playback continues in the new audio format.
Subtitle Selection
1. While a DVD is playing, press the SUBTITLE / RETURN button to display the current language setting, as shown in the
example below.
2. Press the SUBTITLE / RETURN button repeatedly to select the desired subtitle language.
NOTE :
• If only one language is recorded, the language does not change.
• Approximately two seconds later, playback continues with the new subtitle you selected.
• The number of languages recorded differs depending on the disc.
• If no button is pressed within a few seconds, playback continues without changing the current subtitle.
• This function can only be used for discs on which subtitles have been recorded in multiple languages.
• On some DVDs, subtitles are activated from the main menu of the DVD. Press the MENU button to activate the
main menu.
Angle Selection
Some DVDs contain scenes that have been shot from a number of different angles. For these discs, the same
scene can be viewed from each of these different angles.
1. While you are playing a DVD with different angles
recorded, press the ANGLE button to view the number of
current angles available.
2. Press the ANGLE button repeatedly to change the scene
to the next recorded angle.
Sequence of angle shots
(Example)
• Approximately two seconds later, playback continues
from the new angle you selected.
• If no button is pressed within 10 seconds, playback
continues without changing the current angle.
NOTE:
• This function can only be used for discs on which scenes shot from multiple angles have been recorded.
• If only one angle is recorded, “
: [ 1/1 ] ” is displayed.
GB - 15
Basic playback
SPECIAL FUNCTIONS
DISPLAY Function
Using DISPLAY, you can check the current settings of the following items: ANGLE, AUDIO and SUBTITLE.
• While the disc is playing, press the DISPLAY button to display the screen shown below.
Locating a Specific Title
If a DVD disc contains title numbers, you can locate a specific title by directly selecting a title number.
1. In stop mode, press the GOTO button.
2. Press or button to highlight a specific field and press the corresponding number button(s) for the title you want.
3. Press the ENTER button to confirm. The unit will start playback approximately 3 seconds later.
Locating a Specific Chapter / Track
You can locate a specific chapter / track by directly selecting a chapter / track number.
1. Press the GOTO button.
2. Press or button to highlight a chapter / track and press the corresponding number button(s) for the chapter you
want.
3. Press the ENTER button to confirm. The unit will start playback approximately 3 seconds later.
Locating a Specific Time
You can move to a specific location by entering its corresponding time (hours, minutes, seconds)
1. Press the GOTO button.
2. Press or button to highlight time.
3. Press the corresponding number buttons for the setting point you want.
4. Press the ENTER button to confirm. The unit will start playback approximately 3 seconds later.
NOTE:
• Some discs may not respond to this process.
• Some scenes may not be located as precisely as you specified.
• This method for accessing specific locations is available only within the current title of the DVD disc.
GB - 16
CD/DVD PROGRAMMABLE MEMORY
Programmable Memory
The two types of programmed
a
playback provided by this unit are title/chapter programmed playback and track
programmed playback.
k.
Title / Chapter Programmed Playback
1. Press the MEMORY button while the disc is stopped.
2. Enter the title numbers in
. Use or button to move the highlight to
chapter and enter the chapter numbers in
.
3. Use , , or button to move to the other field.
4. Repeat steps 2 to 3.
5. Press the PLAY button to start the programmed playback.
NOTE:
If you press the STOP
OP b
button twice, the programmed selection will be cleared.
Track Programmed Playback
1. Press the MEMORY button while the disc is stopped.
.
2. Enter the track numbers in
3. Use , , or button to move to the other field.
4. Repeat steps 2 to 3.
5. Press the PLAY button to start the programmed playback.
REPEAT PLAYBACK
You can play
y a specific title or chapter repeatedly. (Title repeat, chapter repeat, A-B repeat)
Repeating a Chapter
Repeating a Specific Section
You can play the same chapter repeatedly.
1. While the disc is playing, press the REPEAT DISC
button until the
indicator displays on the screen.
The current chapter is played repeatedly.
You can play a specific section repeatedly.
1. While the disc is playing, press the REPEAT A-B
button at the beginning of the section (
is
displayed) you want to play repeatedly.
2. Press the REPEAT A-B button again at the end of
the section (
is displayed).
3. The unit will immediately begin replaying your
selection.
Repeating a Title
You can play the same title repeatedly.
2. While the disc is playing, press the REPEAT DISC
button until the
indicator displays on the screen.
The current title is played repeatedly.
To Resume Normal Playback
3. While the disc is playing, press the REPEAT DISC
button until the
indicator displays on the screen.
You can play a single track and whole disc repeatedly.
Repeating a Single Track
You can play the same track repeatedly.
1. While the disc is playing, press the REPEAT DISC
button until the
indicator displays on the screen.
The current track is played repeatedly.
To Resume Normal Playback
4. While the disc is playing, press the REPEAT A-B
indicator displays on the
button until the
screen.
NOTE:
• A-B repeat can only be used within the same title. If
the start and end of the section to be repeated are in
different titles, A-B repeat is cancelled.
• The A-B repeat function does not operate in scenes
where different camera angles are recorded.
Repeating a Whole Disc
2. While the disc is playing, press the REPEA
REPEAT DISC
indicator displays on the screen.
button until the
The whole disc is played repeatedly.
To Resume Normal Playback
3. Press the REPEAT DISC button until the
indicator displays on the screen.
GB - 17
PLAYING PICTURE FILE DISC
This unit can play picture files recorded on CD-R and CD-RW discs.
Playing a Picture File Disc
1. Open the disc door.
2. Hold a picture file disc by its edge and gently push it onto the spindle
with the label side facing up, gently pushing until you hear a “click”.
3. Close the disc door.
4. The unit will load the disc and automatically display the contents of the
disc on the screen, while also beginning to play the first picture file.
These files will then be played back one by one.
5. Press
or
button to select a picture file to view.
6. Press the , , or CURSOR button to view and select the files that
you want to view, then press the ENTER button to confirm the selected
file.
NOTE:
• You can press the
PAUSE button to interrupt playback, and press the
PLAY button to resume playback.
• You can use the GOTO function or use the numbered buttons to enter the number of a picture file to quickly
select the image.
• Press the ANGLE button on the remote control to rotate the picture orientation by 90°.
GB - 18
CUSTOMIZING THE FUNCTION SETTINGS
LANGUAGE SETUP
1. Press the SETUP button in stop mode.
2. Use button to change the highlight cursor. Use or button to select a
language, then press the ENTER button. The screen will change to your selected
language immediately.
3. To exit the SETUP MENU and return to the normal screen, press the RETURN
or SETUP button.
VIDEO SETUP
1. Press the SETUP button in stop mode.
2. Use button to select LANGUAGE SETUP, then press or button repeatedly
until VIDEO SETUP appears.
3. Use or button to select the option (BRIGHTNESS or CONTRAST), then
press the button. Use the or button to make adjustments, then press the
ENTER button. (The screen will change to your selected setting).
4. Repeat steps 2 and 3 above to adjust other options.
5. To exit the SETUP MENU and return to the normal screen, press the RETURN
or SETUP button.
SYSTEM SETUP
1. Press the SETUP button in stop mode.
2. Use button to select LANGUAGE SETUP, then press or button repeatedly
until SYSTEM SETUP appears.
3. Use or button to select the option (TV TYPE, PASSWORD, RATING or
DEFAULT), then press the button. Use or button to make adjustments,
then press the ENTER button. (The screen will change to your selected setting).
4. Repeat steps 2 and 3 above to adjust other options.
5. To exit the SETUP MENU and return to the normal screen, press the RETURN
or SETUP button.
Cut off when a wide-screen
video image is played.
TV Type
Pan Scan
• When wide-screen video is played, this mode clips the right and left sides of
the image so that it can be viewed on a conventional screen.
• Some wide-screen DVDs that do not permit Pan Scan mode playback are
automatically played in letter box mode (black bands top and bottom).
Letter Box
PAN SCAN
• When wide-screen video is played in this mode on a conventional screen,
black bands appear at the top and bottom of the screen.
Wide Screen
• This is the correct mode for playing wide-screen videos on a wide-screen.
LETTER BOX
NOTE:
• The displayable picture size is preset on the DVD disc. Therefore the playback
picture of some DVD discs may not conform to the picture size you select.
• When you play DVD discs recorded in the 4:3 aspect ratio, the playback
picture will always appears in the 4:3 aspect ratio regardless of the TV TYPE
setting.
GB - 19
WIDE SCREEN
(continued on next page)
CUSTOMIZING THE FUNCTION SETTINGS
Password
1. Press the SETUP button in stop mode.
2. Use
button to select LANGUAGE SETUP, then press
3. Use
or
or
button repeatedly until SYSTEM SETUP appears.
button to select PASSWORD, enter your 4-digit security code and then press the ENTER button.
If you forget the password, you can erase your current password
by pressing the number 8 button on the remote control four
times, then press the ENTER button to confirm the setting
(PASSWORD : 8 8 8 8).
The Parental lock is
active.
Indicates Parental lock
is NOT active.
Rating
DVD discs are equipped with a password function and are rated according to their content. The contents allowed by
the parental lock level and the way a DVD disc is controlled may vary from disc to disc. For example, if the disc
allowed, you could lock-out violent scenes unsuitable for children or you could lock out playback of the disc altogether.
You cannot play DVD discs rated higher than the level you selected unless you cancel the parental lock function.
The parental lock levels are equivalent to the following ratings.
1 : KID SAFE
5 : PG-R
2:G
6:R
3 : PG
7 : NC-17
4 : PG-13
8 : ADULT
Default
It takes 3-5 seconds to reset the unit to the factory default.
GB - 20
LANGUAGE CODE LIST
GB - 21
MAINTENANCE
Cleaning the Disc
A defective or soiled disc inserted into the unit can cause sound to drop out during playback.
Handle the disc by holding its inner and outer edges.
• Do NOT touch the surface of the unlabeled side of the disc.
• Do NOT stick paper or tape on the surface.
• Do NOT expose the disc to direct sunlight or excessive heat.
• Clean the disc before playback. Wipe the disc from the center outward with a cleaning cloth.
• NEVER use solvents such as benzine or alcohol to clean the disc.
• Do NOT use irregular shaped discs (example : heart shaped, octagonal, etc.). They may cause malfunctions.
Cleaning the Unit
• Be sure to turn the unit off and disconnect the power adapter before maintaining the unit.
• Wipe the unit with a dry soft cloth. If the surfaces are extremely dirty, wipe clean with a cloth that has been
dipped in a weak soap-and-water solution and wrung out thoroughly, then wipe with a dry cloth.
• Never use alcohol, benzine, thinner, cleaning fluid or other chemicals. Do NOT use compressed air to remove dust.
Important Note
Before transporting the unit, remove the disc from the disc compartment.
INSTALLATION GUIDE
GB - 22
TROUBLE SHOOTING GUIDE
SYMPTOM
CAUSE (AND REMEDY)
No power.
• Ensure the the car plug adapter is connected.
• You did not turn on the unit.
The remote does
not function.
•
•
•
•
DVD
No sound or only
a very low-level
sound is heard.
Remove any obstacles between the remote and the unit.
Use the remote near the unit.
Point the remote at the remote sensor on the unit.
Replace the remote control battery.
• Make sure that you've select DVD mode.
• The system is in pause mode. Press the PLAY button to return to normal play mode.
• Fast forward or fast reverse is performed. Press the PLAY button to return to normal play
mode.
• Make sure that AUDIO / VIDEO output and AV IN input connections are correct.
• The DTS DVD disc cannot be decoded to have speaker output.
• This unit is too hot. Turn off the unit for 30 minutes to allow it time to cool down.
No picture
• The region number of the disc doesn't match the region number of this unit.
The picture is not
clear
• Clean the disc.
• The disc is scratched.
Severe hum or
noise is heard.
• The plugs and jacks are dirty. Wipe them with a cloth slightly moistened with alcohol.
• Clean the disc.
The disc does not
play.
•
•
•
•
•
There is no disc inside ("No Disc" appears on the screen).
Insert the disc correctly with the playback side facing forward.
Clean the disc.
A non-NTSC disc has been inserted. The unit and disc region number are incompatible.
Condensation may have formed inside the unit due to a sudden change in temperature.
Wait approximately an hour for it to clear and try again.
Specifications and external appearance are subject to change without notice.
Need More Help?
DO NOT RETURN THIS TO THE STORE
Please visit online help at
http://www.1800customersupport.com
GB - 23
811-P69791-010
Printed in China
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement