Hitachi C 10FR Instruction manual

Model C 10FR Jobsite Table Saw

OFF ON

English

INSTRUCTION MANUAL AND SAFETY INSTRUCTIONS

WARNING

Improper and unsafe use of this power tool can result in death or serious bodily injury!

This manual contains important information about product safety. Please read and understand this manual before operating the power tool. Please keep this manual available for others before they use the power tool.

– 1 –

Hitachi Koki

N136

English

English

CONTENTS

SECTION

Product Specifications ................................................................................................................

Power Tool Safety ......................................................................................................................

Table Saw Safety ........................................................................................................................

Electrical Requirements and Safety ...........................................................................................

Accessories and Attachments ....................................................................................................

Tools Needed for Assembly .......................................................................................................

Carton Contents .........................................................................................................................

Know Your Table Saw ................................................................................................................

Assembly and Adjustments ........................................................................................................

Operation ....................................................................................................................................

Maintenance ...............................................................................................................................

Troubleshooting Guide ...............................................................................................................

Push Stick Pattern ......................................................................................................................

Parts List .....................................................................................................................................

7

7

9

10

PAGE

3

4

5

6

7

17

21

22

23

24

– 2 –

English

WARNING

Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals known to the state of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• Lead based paints

• Crystalline silica from bricks, cement and other masonry products

• Arsenic and chromium from chemically treated lumber

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals, work in a well-ventilated area and work with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles.

PRODUCT SPECIFICATIONS

MOTOR

Type ............................................... Universal

SAW

Table Size with Extension........................ 31-25/32” x 19-21/64”

Amps .............................................. 6.5A

(807mm x 491mm)

Voltage ........................................... 230-240V/50Hz Table Extension ...................................... Right, Rear

Watts .............................................. 1430W

No load speed ................................ 5,000/min

Overload Protection ....................... YES

Extension Fence Capacity (Maximum).... 24” (610mm) Right

Blade Size................................................ 10” (255mm)

Rip Scale ................................................. YES

Rip Fence ................................................ YES

Miter Gauge ............................................ YES

Maximum Cut Depth @ 90º .................... 3-1/8” (80mm)

Maximum Cut Depth @ 45º .................... 2-1/2” (64mm)

Net Weight .............................................. 73 lbs (33.3kg)

WARNING

To avoid electrical hazards, fire hazards or damage to the table saw, use proper circuit protection.

This table saw is wired at the factory for 230-240 Volt operation. It must be connected to a 230-240 Volt / 6.5

Ampere time delay fuse or circuit breaker. To avoid shock or fire, replace power cord immediately if it is worn, cut or damaged in any way. Before using your table saw, it is critical that you read and understand these safety rules. Failure to follow these rules could result in serious injury to you or damage to the table saw.

WARNING

Through poor conditions of the electrical MAINS, shortly voltage drops can appear when starting the

EQUIPMENT. This can influence other equipment (e.g. blinking of a lamp). If the MAINS-IMPEDANCE Zmax <

0.33 OHM, such disturbances are not expected. (In case of need, you may contact your local supply authority for further information).

– 3 –

English

POWER TOOL SAFETY

WARNING

Before using your table saw, it is critical that you read and understand these safety rules. Failure to follow these rules could result in serious injury or damage to the table saw.

Good safety practices are a combination of common sense, staying alert and understanding how to use your power tool. To avoid mistakes that could cause serious injury, do not plug in your power tool until you have read and understood the following safety rules: accessories. The use of improper accessories may cause injury to you or damage to the tool.

1. READ and become familiar with this entire

Operator’s Manual. LEARN the tool’s applications, limitations and possible hazards.

WARNING

Look for this symbol that identifies important safety precautions. It means BE ALERT! YOUR

SAFETY IS INVOLVED!

15. REMOVE ADJUSTING KEYS AND WRENCHES.

Form the habit of checking to see that keys and adjusting wrenches are removed from the tool before turning ON.

16. NEVER LEAVE TOOL RUNNING UNATTENDED.

TURN THE POWER OFF. Do not leave the tool before the blade comes to a complete stop.

17. NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is unintentionally contacted.

3. NEVER OPERATE THIS MACHINE WITHOUT THE

SAFETY GUARD IN PLACE FOR ALL THROUGH

–SAWING OPERATIONS.

18. DO NOT OVERREACH. Keep proper footing and balance at all times.

4. DO NOT USE IN A DANGEROUS ENVIRONMENT such as damp or wet locations or in the rain. Keep work area well lighted.

19. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for most efficient and safest performance.

Follow instructions for lubricating and changing accessories.

5. DO NOT use power tools in the presence of flammable liquids or gases.

6. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.

20. CHECK FOR DAMAGED OR LOOSE PARTS.

Check for alignment of moving parts, binding of moving parts, loose mounting and any other conditions that may affect its safe operation. A guard or other part that is loose or damaged should be properly adjusted, repaired or replaced.

7. KEEP CHILDREN AWAY. All visitors should be kept at a safe distance from the work area.

21. MAKE WORKSHOP CHILDPROOF with padlocks, master switches or by removing starter keys.

8. DO NOT FORCE THE TOOL. It will do the job better and safer if used at the rate for which it was designed.

22. DO NOT operate the tool if you are under the influence of any drugs, alcohol or medication that could impair your ability to use the tool safely.

9. USE THE RIGHT TOOL. Don’t force the tool or attachment to do a job for which it is not designed.

10. WEAR PROPER APPAREL. DO NOT wear loose clothing, gloves, neckties, rings, bracelets or other jewelry that may get caught in moving parts.

Non-slip footwear is recommended. Wear protective hair covering to contain long hair.

23. USE A DUST COLLECTION SYSTEM whenever possible. Dust generated from certain materials can be hazardous to your health and, in some cases, a fire hazard. Always operate the power tool in a well-ventilated area with adequate dust removal.

11. WEAR A FACE MASK OR DUST MASK. Sawing, cutting and sanding operations produce dust.

12. DISCONNECT TOOLS before servicing and when changing accessories, such as blades, cutters, etc.

13. REDUCE THE RISK OF UNINTENTIONAL

STARTING. Make sure the switch is in the OFF position before plugging tool into the power supply.

24. ALWAYS WEAR EYE PROTECTION. Any power tool can throw debris into your eyes that could cause permanent eye damage. ALWAYS wear safety goggles (not glasses) that comply with ANSI safety standard Z87.1. Everyday glasses have only impact resistant lenses. They ARE NOT safety glasses.

NOTE: Glasses or goggles not in compliance with

ANSI Z87.1 could cause serious injury when they break.

14. USE ONLY RECOMMENDED ACCESSORIES.

Consult the Operator’s Manual for recommended

– 4 –

25. DIRECTION OF FEED. Feed work into a blade or cutter against the direction of rotation of the blade or cutter only.

English

TABLE SAW SAFETY

1. ALWAYS USE SAW BLADE GUARD, splitter and antikickback pawls for every operation for which they can be used, including through sawing.

Through sawing operations are those in which the blade cuts completely through the workpiece when ripping or crosscutting.

12. PROVIDE ADEQUATE SUPPORT to the rear and the sides of the saw table for long or wide workpieces.

2. ALWAYS HOLD WORK FIRMLY against the miter gauge or rip fence.

3. ALWAYS USE a push stick, especially when ripping narrow stock. Refer to ripping instructions in this

Operator’s Manual where the push stick is covered in detail. A pattern for making your own push stick is included on page 23.

13. AVOID KICKBACKS (work thrown back towards you) by keeping the blade sharp, the rip fence parallel to the saw blade and by keeping the splitter, anti-kickback pawls and guards in place, aligned and functioning. Do not release work before passing it completely beyond the saw blade. Do not rip work that is twisted, warped or does not have a straight edge to guide it along the fence.

14. AVOID AWKWARD OPERATIONS and hand positions where a sudden slip could cause your hand to move into the saw blade.

4. NEVER PERFORM ANY OPERATION FREEHAND, which means using only your hands to support or guide the workpiece. Always use either the fence or the miter gauge to position and guide the work.

WARNING: FREEHAND CUTTING IS THE MAJOR

CAUSE OF KICKBACK AND FINGER/HAND

AMPUTATIONS.

5. NEVER STAND or have any part of your body in line with the path of the saw blade. Keep your hands out of the saw blade path.

15. NEVER USE SOLVENTS to clean plastic parts.

Solvents could possibly dissolve or otherwise damage the material. Only a soft damp cloth should be used to clean plastic parts.

16. MOUNT your table saw on a bench or stand before performing any cutting operations. Refer to

ASSEMBLY AND ADJUSTMENTS on page 10.

17. NEVER CUT METALS or materials that may make hazardous dust.

6. NEVER REACH behind or over the cutting tool for any reason.

18. ALWAYS USE IN A WELL-VENTILATED AREA.

Remove sawdust frequently. Clean out sawdust from the interior of the saw to prevent a potential fire hazard. Attach a vacuum to the dust port for additional sawdust removal.

7. REMOVE the rip fence when crosscutting.

8. DO NOT USE a molding head with this saw.

9. FEED WORK INTO THE BLADE against the direction of rotation only.

10. NEVER use the rip fence as a cut-off gauge when crosscutting.

11. NEVER ATTEMPT TO FREE A STALLED SAW

BLADE without first turning the saw OFF. Turn power switch OFF immediately to prevent motor damage.

19. NEVER LEAVE THE SAW RUNNING

UNATTENDED. Do not leave the saw until the blade comes to a complete stop.

20. For proper operation follow the instructions in this

Operator’s Manual entitled ASSEMBLY AND

ADJUSTMENTS (Page 10). Failure to provide sawdust fall-through and removal hole will allow sawdust to build up in the motor area resulting in a fire hazard and potential motor damage.

– 5 –

English

ELECTRICAL REQUIREMENTS AND SAFETY

CONNECTING TO THE POWER SUPPLY

Check that the power supply and plug used is in accordance with your drill press. Have a look at the rating plate of the motor or the rating on the drill press. Any changes should always be carried out by a qualified electrician.

WARNING

This machine must be earthed.

If not properly earthed this machine can cause an electrical shock. Be sure that the power supply outlet is earthed. If there is any doubt, have it checked by a qualified electrician.

WARNING

Avoid contact with the terminals on the plug when installing (removing) the plug to (from) the power supply outlet. Contact will cause a severe electrical shock.

USING AN EXTENSION LEAD

The use of any extension lead will cause some loss of power. To keep this to a minimum and to prevent overheating and motor burn-out, ask advice from a qualified electrician to determine the minimum wire size of the extension lead.

The extension lead should be equipped with an earthed type plug that fits the power supply outlet at one end, and with an earthed type socket that fits the plug of this machine at the other end.

– 6 –

English

ACCESSORIES AND ATTACHMENTS

RECOMMENDED ACCESSORIES

WARNING

WARNING

Visit your Hardware Department or see the Power and Hand Tools Catalog to purchase recommended accessories for this power tool.

To avoid the risk of personal injury:

• Do not use a dado with a diameter larger than 6”

(152.4mm).

• Maximum dado width is 1/2” (12.7mm). DO NOT

USE WIDER COMBINATIONS.

• Do not use molding head set with this saw.

• Do not modify this power tool or use accessories not recommended by Store.

TOOLS NEEDED FOR ASSEMBLY

Supplied Not Supplied

Wrench

Wrench

Medium Screwdriver

#2 Phillips Screwdriver

Adjustable Wrench

3 mm Hex Wrench Straight Edge Combination Square

CARTON CONTENTS

UNPACKING AND CHECKING CONTENTS

Separate all parts from packing materials. Check each part with the illustration on the next page and the “Table of Loose Parts” to make certain all items are accounted for, before discarding any packing material.

TABLE OF LOOSE PARTS

ITEM DESCRIPTION

A Table saw assembly

B Blade

C Blade wrenches

D Miter gauge

E Hex key

F Bolt, flat washer, toothed washer, oval washer, spring washer

G Blade guard and splitter assembly

H Rip fence

I Rear table extension

J Rear table extension tube

K Location seat

L Dome nuts

M Handwheels

N Table extension

O Dust bag

P Parallel washer hardware

QUANTITY

1

1

2

1

1

1 each

2

1

1

1

1

2

1

1

4

2

– 7 –

STAND:

Q Stand assembly

R Hex. head bolts

S Flat washers

T Roller wheels

U Square neck bolts

V Nuts

W Support rod

X Batteries

WARNING

2

2

1

2

1

4

4

2

If any part is missing or damaged, do not attempt to assemble the table saw, plug in the power cord, or turn the switch ON until the missing or damaged part is obtained and is installed correctly.

NOTE: To make assembly easier, keep contents of box together. Apply a coat of automobile wax to the table.

Wipe all parts thoroughly with a clean dry cloth. This will reduce friction when pushing the workpiece. To avoid injury, the styrofoam block should be removed between the motor and the table.

English

UNPACKING YOUR TABLE SAW

Q

OFF ON

A

C

L

E F

T

G

P

R S

V

U

X

K

B

W

D

O

N

H M

– 8 –

J

I

English

KNOW YOUR TABLE SAW

The Front of Table Saw

Blade guard with LED lighting

Cutting line indicator

Miter gauge

Table Insert

Bevel angle pointer & scale

Overload reset switch

Miter gauge storage

Fence storage

Stand handle

OFF

ON

Rip fence

Side table extension

Extension wing locking lever

Blade tilting handwheel

Blade bevel lock knob

ON/OFF switch with key

Stand wheel

Blade elevation handwheel

Lock lever

Dust Bag

Stand hook

Support rod

The Rear of Table Saw

Cord wrap

– 9 –

English

ASSEMBLY AND ADJUSTMENTS

ESTIMATED ASSEMBLY TIME 25~40 MINUTES

FOLDING THE STAND (FIG. A-1)

1. Release the stand hook (1).

2. Unfold the wider leg set (2). Pull the lever (3)

downward and push it to lock in place. Then, put

down the wider leg set on the ground.

3. Lift the stand up and unfold the narrower leg set (4).

4. Pull the lever downward and push it to lock in place.

NOTE: Make sure the stand is locked securely.

NOTE: Do not over tighten bolts holding saw to stand. This will damage the saw base.

5. Carefully set the saw in its upright position on a

clean level surface.

6. Thread the support rod (10) into the socket (11) at the

rear of stand. Adjust the adjustable foot (12) properly.

Fig. A-2

Fig. A-1

OFF ON

6

6

1

12

8 7

10

3

11

2

6

9

4

5

ASSEMBLING THE ROLLER WHEEL (FIG. A-1)

Attach the roller wheel (7) to roller wheel bracket using square neck bolt (8) and nut (9) as shown.

INSTALLING THE DUST BAG (FIG. A-1)

1. Place the dust bag (6) around the neck of the dust chute and tie the dust bag by pulling the string tight and secure with the spring-loaded tie clip.

NOTE: Do not use this saw to cut and sand metal.

The hot chips or sparks may ignite sawdust or the bag material.

ASSEMBLING TABLE SAW TO STAND (FIG. A-1,A-2)

1. Place stand on level surface and adjust front right adjustable stand pad (5) to make stand stable.

2. Place table saw on the top of stand aligning holes in base with holes in s tand.

3. Insert four hex. head bolts (6) through flat washer

and holes in base and s tand.

4. Tighten all four bolts .

– 10 –

FOLDING THE TABLE SAW/STAND (FIG. A-1, A-3)

1. Release the lever of the narrower leg set and keep

the lever on top. Hold the table and lift the saw up just

above the ground and fold up the narrower leg set.

NOTE: The narrow leg set can be held by a “spring clip”.

2. Then reposition on the saw onto the ground. Release

the lever of the wider leg and keep the lever on top

set then fold the leg set up into position.

3. Then fix the legs with stand hook.

SETTING UP THE TABLE SAW/STAND (FIG. A-3)

1. Release the stand hook.

2. Unfold the wider leg set and lock the lever in place.

3. Put down the wider leg set on the ground, lift the saw

up and unfold the narrower leg set.

4. Pull the lever downward and lock into place.

NOTE: Make sure the saw is locked in position

securely before operation.

Fig. A-3 FOLDING

1

1

SET-UP

2

2

3

SAW MOUNTED TO WORK SURFACE (FIG. B)

1. If the leg set will not be used, the saw must be properly secured to a sturdy workbench using the four mounting holes at the base of the saw.

2. The surface of the table where the saw is to be mounted must have a hole large enough to facilitate sawdust fall-through and removal.

3. Square the saw on the mounting surface and mark the location of the four 3/8” (9.5mm) mounting holes

(1).

4. Drill 3/8” (9.5mm) hole into the mounting surface.

5. Mark an 11” (279.4mm) square (2) centered between the four mounting holes (1).

6. Cut out and remove the square.

7. This opening will allow sawdust to fall through the saw base.

8. Place the saw on the work surface, and align the mounting holes of the saw with those drilled through the surface.

9. Fasten the saw to the work surface.

WARNING

Do not operate this machine on the floor. This is very dangerous and may cause serious injury.

Fig. B

English

INSTALLING BATTERY FOR LED LIGHTING SPACE

(FIG. D)

1. Open the cover (1) of battery box on the top of blade

guard.

2. Install 2 pieces of 1.5V 3A batteries into the battery

box in right direction.

3. Close the cover.

4. Turn on the switch (2) to check the LED lighting.

Fig. D 1

2

SQUARE

CUTOUT

2

1

BLADE RAISING HANDWHEEL (FIG. E, F)

1. Attach the handwheel (1) to the elevation screw (2)

at the front of the saw. Make sure the slots (3) in the

hub of the handwheel engage with the pins (4).

(Fig. E)

2. Attach and tighten the dome nut (5) at the end of the

shaft (Fig. F).

Fig. E

WARNING

Failure to provide the sawdust fall-through hole will cause sawdust to build up in the motor area, which may result in fire or cause motor damage.

KEEPING THE AREA CLEAN

1. Sawdust and wood chips that fall from under the saw will accumulate on the floor.

2. Make it a practice to pick up and discard this dust when you have completed cutting.

ADJUSTING THE CUTTING LINE INDICATOR (FIG. C)

1. Take off the cover (1) by loosening screws (2).

2. Adjust the pointer (3) to align to the blade.

3. Mount the cover on the table to fix the pointer.

NOTE: The pointer was set up to align to the right side of the blade when packing.

Fig. C

3

1

2 4

BLADE TILTING HANDWHEEL (FIG. F)

1. Attach the other handwheel (6) to the blade tilting

screw on the side of the saw in the same manner as

above.

2. Attach and tighten the handwheel dome nut (5).

Fig. F

3

1

5

6

2

– 11 –

English

RIP FENCE (FIG. G)

1. Lift upward on the rip fence handle (1) so the rear

holding clamp (2) is fully extended.

2. Place the rip fence on the saw table, and attach the

set plate (3) under the fence handle(1) to the rail first.

3. Push down on the fence handle (1) to lock.

Fig. G

2

1

3

INSTALLING AND CHANGING THE BLADE (Fig. H, I, J)

WARNING

• To avoid injury from an accidental start, make

sure the switch is in the OFF position and the

plug is not connected to the power source outlet.

• To avoid serious injury, the rear of the table insert must be level with the table. To adjust rear of table insert, adjust the screw (3) in or out until the rear of the insert is level to or slightly above the table. To raise the insert, turn the screw counterclockwise, to lower the insert, turn the screw clockwise. NOTE: A rubber adjusting spacer (4) is provided under rear of insert for this purpose.

1. Remove the table insert (1) by removing the two screws (2, 3). Be careful not to lose the rubber adjusting spacer (4) that is on the back screw (3) beneath the table insert (Fig. H).

Fig. H

1

3

1

4. Remove the arbor nut (5) and flange (6), remove

blade.

5. Install the saw blade onto the arbor with the BLADE

TEETH POINTING TOWARD THE FRONT OF THE

SAW.

6. Install the flange (6) against the blade and thread

the arbor nut (5) as far as possible by hand. Ensure

that the blade is flush against the inner side of the

blade flange.

WARNING

To avoid possible injury and damage to the workpiece be sure to install the blade with the teeth pointing toward the front of table in the direction of the rotation arrow on the blade guard.

Fig. I

4

5

6

7. To tighten the arbor nut (5) place the open-end

wrench jaws on the flats of the saw arbor to keep the

arbor from turning. (Fig. J )

8. Place the box-end wrench (8) on the arbor nut (5),

and turn clockwise (to the rear of the saw table).

9. Replace the blade insert in the table recess, insert

the screws through the front and rear holes and

tighten, remembering the rubber adjusting spacer

under the rear of the insert and leveling the rear of

the insert to the table.

Fig. J 7

8

5

2

4

2. Raise the blade arbor (4) (Fig. G) to the maximum

height by turning the blade raising handwheel

counterclockwise.

3. Place the open-end wrench jaws on the flats of the

saw arbor to keep the arbor from turning. (Fig. H)

and place the box-end wrench (8) on the arbor nut

(5), and turn counterclockwise.

WARNING

To avoid injury from a thrown workpiece, blade parts, or blade contact, never operate saw without the proper insert in place. Use the saw blade insert when sawing.

Use the dado head insert when using a dado.

– 12 –

BLADE GUARD ASSEMBLY (FIG. K, L, M)

1. Set the blade to maximum height and the tilt to zero

degrees on the bevel scale with the handwheels.

Lock the blade lock knob.

2. Place the external toothed lock washer (1), a steel

flat washer (2) and a spring washer (10) onto the

long hex head bolt (3). Insert the bolt into the splitter

bracket (4) as shown. (Fig. K)

Fig. K

4

English

WARNING

Improper splitter alignment can cause “kickback” and serious injury.

Fig. M 8 Kickback pawl

7

9

3

11

1

2 10

3. Place the oval washer (5) on the pivot rod (6). (Fig. L)

4. Install the bracket assembly (4) at the rear of the saw

table and snugly – do not tighten. Thread the bolt (3)

into the internally threaded pivot rod.

NOTE: The splitter is removed from the illustration for

clarity.

Fig. L

5 6

3

INSTALLING TABLE SIDE EXTENSION (FIG. N)

1. Identify the right hand table extension.

NOTE: For illustration purposes the view in Fig. N looks “through” the saw table to the under side of the table. The right hand table extension is the one with the measuring scale (1) visible from the front of the saw when it is installed to the right hand side of the saw table (Fig. N).

2. Open both front and rear cam locking levers (2) on

the right hand side of the saw base by pulling them out from the cam locking assemblies (4).

3. Insert the table extension mounting tubes (3) into the

two matching holes in the cam lever assemblies.

NOTE: Make sure the front mounting tube has the

measuring scale visible from the front of the saw.

4. Slide the table extension toward the table until it rests against the saw table.

5. Lock both cam locking levers by pushing them in

toward the cam locking lever assemblies.

Fig. N

5. Position the blade guard arm (7) to the rear of the

table.

6. Using a straight edge, check to see if the blade

guard splitter (8) is aligned with the saw blade (9).

7. If straightening adjustment is necessary, loosen the

bolt (3) and shift the splitter assembly to right or left,

or rotate.

8. When the splitter is properly aligned with the saw

blade, tighten the bolt tightly.

9. If height adjustment is necessary, loosen the bolts

(11) and raise the splitter assembly to the desired

height and tighten the bolts. (Fig. K)

10. NOTE: The splitter must always be correctly aligned

so that the cut workpiece will pass on either side

without binding or twisting to the side.

– 13 –

4

2

3

English

INSTALLING TABLE SIDE EXTENSIONS- cont’d (FIG. O)

6.

Snap one short location seat (5) over the end of the

rear table extension tube (3). Make sure the locating

pin (6) in the location seat fits into the matching hole

in the extension tube (Fig. O).

NOTE: Install location seat on front table extension

tube.

NOTE: For illustration purposes the view in Fig. O looks “through” the saw table to the under side of the table.

Fig. O 6 5

3

INSTALLING REAR TABLE EXTENSION (FIG. P)

1. Place the rear table extension onto the two rear table

extension tubes (1).

2. Snap two long location seats (4) over the two rear

table extension tubes (1). Make sure the locating pin in the location seat fits into the matching hole (5) in the extension tube.

3. Insert rear table extension tubes (1) into the two holes in the rear of the saw table (3) and into extension tube brackets under the table.

4. Position rear table support so instruction labels are up.

5. Snap one short location seat (4) over the end of the

left rear table extension tube (1). Make sure the

locating pin in the location seat fits into the matching

hole in the extension tube.

Fig. P

5

4

3

ADJUSTING REAR TABLE EXTENSION

1. Rear table extension should be positioned as close as possible to the rear of the table when ripping short

workpieces.

2. Rear table extension should be pulled out fully until

the location seat prevents it from moving outward

when ripping long workpieces that require extra

support as you are completing the cut.

RIP FENCE ADJUSTMENT (FIG. Q)

1. The fence (1) is moved by lifting up on the handle (2)

and sliding the fence to the desired location. Pushing

down on the handle locks the fence in position.

2. Position the fence on the right side of the table, and

along one edge of the miter gauge grooves.

3. Lock the fence handle. The fence should be parallel

with the miter gauge groove.

4. If adjustment is needed to make the fence parallel to

the groove, do the following:

• Loosen the two screws (4) and lift up on the

handle (2).

• Hold the fence bracket (5) firmly against the front

of the saw table. Move the far end of the fence

until it is parallel with the miter gauge groove.

• Tighten both screws and push the handle to lock.

5. If fence is loose when the handle is in the locked

(downward) position, do the following:

• Move the handle (2) and then remove cover (3)

pward and turn the adjusting nut (6) clockwise until

the rear clamp is snug. Do not turn the adjusting

screw more than 1/4 turn at a time.

• Over-tightening the adjusting screw will cause the

fence to come out of alignment.

WARNING

Failure to properly align fence can cause “kickback” and serious injury.

Fig. Q

3

1

4

6

1

2

5

– 14 –

English

RIP FENCE INDICATOR ADJUSTMENT (FIG. Q)

1. The rip fence indicator (6) points to the measurement

scale (8). The scale shows the distance from the side

of the fence to nearest side of the blade.

2. Measure the actual distance with a rule. If there is a

difference between the measurement and the

indicator, adjust the indicator (6).

3. Loosen the screw (7) and slide the indicator to the

correct measurement on the scale. Tighten the screw

and remeasure with the rule.

WARNING

To avoid injury from an accidental start, make sure the switch is in the OFF position and the plug is not connected to the power source outlet.

ADJUSTING THE 90° AND 45° POSITIVE STOPS

(FIG. Q-1, Q-2, Q-3)

Your saw has positive stops that will quickly position the saw blade at 90° to the table. Make adjustments only if necessary.

90° (0°) Stop

1. Disconnect the saw from the power source.

2. Turn the blade elevation handwheel and raise the

blade to the maximum elevation.

3. Loosen the blade bevel lock knob (2) and move the

blade to the maximum vertical position. Tighten the

lock knob (2).

4. Place a combination square on the table and against

the blade (1) to determine if the blade is 90° to the

table. (Fig. Q-2)

5. If the blade is not 90° (0°) to the table, loosen the two set screws (4), located on the bottom of the table saw, (Fig. Q-3) with the hex key, and back off the collar.

6. Loosen the bevel lock knob. Turn the blade tilting

handwheel to move the blade until it is 90° (0°) to the

table.

7. Adjust the collar (5) so it contacts the bracket (3) when the blade is 90° (0°) to the table. Tighten the two set screws (4).

2

Fig. Q-1

Fig. Q-2

90°

1

4

5

3

45°

3

45° Stop

1. With the blade in the upright 90° position, loosen the

bevel lock knob and move the blade to the 45°

position as far as it will go.

2. Place the combination square on the table as shown

in (Fig. Q-2) to check if the blade is 45° to the table.

3. If the blade is not 45° to the table, adjust the screw

(4) (Fig. Q-3) with a screw driver until the blade is 45°

to the table.

4. Tighten the bevel lock knob.

5. Tighten the screw (4) until resistance is felt. Do not

overtighten.

BLADE TILT POINTER

1. When the blade is positioned at 90°, adjust the blade

tilt pointer to read 0° on the scale.

2. Loosen the holding screw, position pointer over 0°

and tighten the screw.

NOTE: Make a trial cut on scrap wood before making critical cuts. Measure for exactness.

Fig. Q-3

5 4 3

OFF ON

– 15 –

English

BLADE PARALLEL TO THE MITER GAUGE GROOVE

(FIG. R, S)

WARNING

This adjustment was made at the factory, but it should be rechecked and adjusted if necessary.

WARNING

To prevent personal injury:

• Always disconnect plug from the power source when

making any adjustments.

• This adjustment must be correct or kickback could

result in a serious injury and accurate cuts can not

be made.

1. Remove the yellow switch key and unplug the saw.

2. Move the blade guard out of the way.

3. Raise the blade to the highest position and set at the

0° angle (90° straight up).

4 Select and mark, with a felt tip marker, a blade tooth

having a “right set”.

5. Place the combination square base (1) into the right

side miter gauge groove (2). (Fig. R)

6. Adjust the rule so it touches the front marked tooth

and lock ruler so it holds its position in the square

assembly.

7. Rotate the blade bringing the marked tooth to the

rear and about 1/2 inch above the blade.

8. Carefully slide the combination square to the rear

until the ruler touches the marked tooth.

9. If the ruler touches the marked tooth at the front and

rear position, no adjustment is needed at this time. If

not, perform adjustment procedure described in next

section.

Fig. R

4. Tighten the nuts (1) and the left screw and

remeasure, as described in steps 4 to 9 in the prior

section.

5. Recheck blade clearance making sure that the

blade does not hit the table insert or other parts

when at the 90° and 45° settings.

Fig. S

1

STORAGE (FIG. T, T-1)

Rip fence and miter gauge

Storage brackets (1) for the rip fence (3) and miter gauge (2) are located on the left side of the saw housing.

NOTE:Adjust the miter gauge to 45 to the storage.

0 ~60 0 before putting

Fig. T

Fig. T-1

1

1

2

3

2

ADDITIONAL BLADE ADJUSTMENTS (Fig. S)

The adjusting mechanism is located on top of blade height adjusting handwheel under the tabletop. If the front and rear measurements are not the same, adjust the alignment by the mechanism as follows:

If the blade is partial to right side:

1. Loosen the two nuts (1) and the right side screw,

then adjust the left side screw.

2. Tighten the nuts (1) and the right screw and

remeasure, as described in steps 4 to 9 in the prior

section.

If the blade is partial to left side:

3. Loosen the two nuts (1) and the left side screw, then

adjust the right screw.

– 16 –

Blade (Fig. T-2)

1. Loosen and remove the knob (1) on the right side of

the saw housing.

2. Place extra blades onto the arbor. Replace the knob

and tighten.

Fig. T-2

1

English

Fig. U

OFF ON

3

OPERATION

BASIC SAW OPERATIONS

RAISE THE BLADE (FIG. U)

To raise or lower the blade, turn the blade elevation handwheel (1) to the desired blade height, and then tighten the bevel lock knob (2) to maintain the desired blade angle.

OVERLOAD PROTECTION (FIG. W)

This saw has an overload relay button (3) that resets the motor after it shuts off due to overloading or low voltage.

If the motor stops during operation, turn the ON / OFF switch to the OFF position. Wait about five minutes for the motor to cool, push in on the reset button and turn the switch to the ON position.

WARNING

To avoid injury, the ON / OFF switch should be in the

OFF position and the plug removed from the power source while the cool down takes place, to prevent accidental starting when the reset button is pushed.

Overheating may be caused by misaligned parts or a dull blade. Inspect your saw for proper setup before using it again.

1 2

TILTING THE BLADE (FIG. U)

1. To tilt the saw blade for bevel cutting, loosen the lock knob (2) and turn the tilting handwheel (3).

2. Tighten the lock knob (2) to secure.

USING THE TABLE EXTENSION (FIG. X, X-1)

If the table extension is not parallel with the table.

Remove the bolts (1) and position the parallel washers

(2) between the table extension and tube until it is parallel with the table, then tighten the bolts.

NOTE: Parallel washers (2) see page 7 for table of loose parts ITEM: P.

ON/OFF SWITCH (FIG. V)

The ON / OFF switch has a removal key. With the key removed from the switch, unauthorized and hazardous use by children and others is minimized.

1. To turn the saw ON, insert key (1) into the slot in the switch (2). Move the switch upward to the ON position.

2. To turn the saw OFF, move the switch downward.

3. To lock the switch in the OFF position, grasp the end

(or yellow part) of the switch key (1) and pull it out.

4. With the safety switch key removed, the switch will not operate.

5. If the safety switch key is removed while the saw is running, it can be turned OFF but cannot be restarted without inserting the safety switch key.

Fig. X

2

1

NOTE: Move and lock the fence to the 381mm left or right side scale. The fence is now clear of the table.

Fig. V

1. Release the extension lock handles.

2. Slide the extension out until the correct measurement

is displayed on the tube scale. The user sights the

scale off the edge of the table.

3. Tighten all extension lock handles.

3

Fig. X-1

OFF

ON 1

2

Right side scale of table extension

– 17 –

English

CUTTING OPERATIONS

There are two basic types of cuts: ripping and crosscutting. Ripping is cutting along the length and the grain of the workpiece. Crosscutting is cutting either across the width or across the grain of the workpiece.

Neither ripping nor crosscutting may be done safely freehand. Ripping requires the use of the rip fence, and crosscutting requires the miter gauge.

WARNING

AVOID KICKBACK by pushing forward on the section of the workpiece that passes between the blade and the fence. Never perform any freehand operations.

Fig. Y

WARNING

Before using the saw each and every time, check the following:

1. The blade is tightened to the arbor.

2. The bevel angle lock knob is tight.

3. If ripping, the fence is locked into position & is parallel to the miter gauge groove.

4. The blade guard is in place and working properly.

5. Safety glasses are being worn.

The failure to adhere to these common safety rules, and those printed in the front of this manual, can greatly increase the likelihood of injury.

1

NOTE: Always use a push stick. When width of the rip is narrower than 2” (51mm) the push stick cannot be used because the guard will interfere…therefore, use the auxiliary fence so the push stick can be used as shown on page 23.

RIPPING (FIG. Y, Z)

WARNING

To prevent serious injury:

• Never use a miter gauge when ripping.

• Never use more than one rip fence during a single cut.

• Do not allow familiarity or frequent use of your table saw to cause careless mistakes. Remember that even a careless fraction of a second is enough to cause a severe injury.

• Keep both hands away from the blade and clear from the path of the blade.

• The workpiece must have a straight edge against the fence and must not be warped, twisted, or bowed when ripping.

1. Remove the miter gauge and store it in the “storage” compartment in the base of the saw.

2. Secure the rip fence to the table.

3. Raise the blade so it is about 1/8” higher than the top of the workpiece.

4. Place the workpiece flat on the table and against the fence. Keep the workpiece away from the blade.

5. Turn the saw ON and wait for the blade to come to full speed.

6. Slowly feed the workpiece into the blade by pushing forward only on the workpiece section (1) that will pass between the blade and the fence. (Fig. Y)

– 18 –

7. Keep your thumbs off the table top. When both of your thumbs touch the front edge of the table (2), finish the cut with a push stick. To make an additional push stick, use the pattern on page 23.

8. The push stick (3) should always be used. (Fig. Z)

9. Continue pushing the workpiece with the push stick (3) until it passes through the blade guard and clears the rear of the table.

10.Never pull the piece back when the blade is turning.

Turn the switch OFF. When the blade completely stops, you can then remove the workpiece.

Fig. Z

2

1

3

English

BEVEL RIPPING

This cut is the same as ripping except the blade bevel angle is set to an angle other than “0°”.

WARNING

Cut only with the workpiece and the fence on the right side of the blade.

RIPPING SMALL PIECES with the proper operation of the sawblade guard. When cutting long workpieces, you can make a simple outfeed support by clamping a piece of plywood to a sawhorse.

Fig. AA

3

1

2

WARNING

Avoid injury from the blade contact. Never make through saw cuts narrower than 1/2” (12.7mm) wide.

Fig. AA-1

1. It is unsafe to rip small pieces. Instead, rip a larger

piece to obtain the size of the desired piece.

2. When a small width is to be ripped and your hand

cannot be safely put between the blade and the rip

fence, use one or more push sticks to move the

workpiece.

CROSSCUTTING (FIG. AA)

WARNING

To prevent serious injury:

• Do not allow familiarity or frequent use of your table saw to cause careless mistakes. Remember that even a careless fraction of a second is enough to cause a severe injury.

• Keep both hands away from the blade and the path of the blade.

1

BEVEL CROSSCUTTING (FIG. BB) 0°~45° BLADE

BEVEL & 90° MITER ANGLE

This cutting operation is the same as crosscutting except the blade is at a bevel angle other than 0°.

WARNING

Always work to the right side of the blade during this type of cut. The miter gauge must be in the right side groove because the bevel angle may cause the blade guard to interfere with the cut if used on the left side groove.

1. Remove the rip fence and place the miter gauge in the left side groove.

2. Adjust the blade height so it is 1/8” (3.18mm) higher than the top of the workpiece.

3. Hold the workpiece firmly against the miter gauge

with the blade path in line with the desired cut

location. Move the workpiece to one inch distance

from the blade.

4. Start the saw and wait for the blade (1) to come up to

full speed.

5. Keep the workpiece (2) against the face of the miter

gauge (3) and flat against the face of the gauge and

flat against the table. Then slowly push the workpiece

through the blade. (Fig. Y)

6. Do not try to pull the workpiece back with the blade

turning. Turn the switch OFF, and carefully slide the

workpiece out when the blade is completely stopped.

1. Adjust the blade (1) to the desired angle, and tighten the blade bevel lock knob.

2. Tighten miter lock handle (2) at 90°.

3. Hold workpiece (3) firmly against the face of the miter gauge throughout the cutting operation.

Fig. BB

1 2

WARNING

3

USING WOOD FACING ON THE MITER GAUGE

(FIG. AA-1)

Slots are provided in the miter gauge for attaching an auxiliary facing (1) to make it easier to cut very long or

COMPOUND MITER CROSSCUTTING (FIG. CC)

0°~45° BLADE BEVEL & 0°~45° MITER ANGLE

This sawing operation is combining a miter angle with a bevel angle. short pieces. Select a suitable piece of smooth wood, drill two holes through it and attach it to the miter gauge with screws. Make sure the facing does not interfere

Always work to the right side of the blade during this type of cut. The miter gauge must be in the right

– 19 –

English side groove because the bevel angle may cause the blade guard to interfere with the cut if used on the left side groove.

1. Set the miter gauge (3) to the desired angle.

2. Place the miter gauge in the right side groove of the table.

3. Set the blade (1) bevel to the desired bevel angle and tighten the blade bevel lock knob.

4. Hold workpiece (2) firmly against the face of the miter gauge throughout the cutting operation.

Fig. CC

1

3 2

MITERING (FIG. DD) 0°~45° MITER ANGLE

This sawing operation is the same as crosscutting except the miter gauge is locked at an angle other than 90°.

1. Set the blade (1) to 0° bevel angle and tighten the blade bevel lock knob.

2. Set the miter gauge (3) at the desired miter angle and lock in position by tightening the miter gauge locking handle.

3. Hold the workpiece (2) firmly against the face of the miter gauge throughout the cutting operation.

Fig. DD

3

2 1

Fig. EE 3

1

2

AUXILIARY FENCE (FIG. FF)

Making the base:

• Start with a piece of 3/8” (9.5mm) plywood at least

5-1/2” (140mm) wide or wider and 30” (762mm) long

or longer.

• Cut the piece to shape and size shown:

Making the side:

• Start with a piece of 3/4” (19.1mm) plywood at least

2-3/8” (60mm) wide or wider and 27” (686mm) long or longer.

• Cut the piece to shape and size shown:

Putting it together:

• Put the pieces together, as shown:

WARNING

Make sure the screw heads do not stick out from the bottom of the base, they must be flush or recessed.

The bottom must be flat and smooth enough to rest on the saw table without rocking.

Fig. FF

30” (762mm)

2-5/8” (67mm)

3/8” (9.5mm) Thick plywood base

27” (686mm)

3/4” (19mm) Thick plywood side

4-3/4” (121mm)

1-1/4” (32mm)

USING WOOD FACING ON THE RIP FENCE (FIG. EE)

When performing some special cutting operations, add a wood facing (1) to either side of the rip fence (2).

1 . Use a smooth straight 3/4” (19 mm) thick wood

board (1) that is as long as the rip fence.

2. Attach the wood facing to the fence with wood screw

(3) through the hole in the fence. A wood fence

should be used when ripping material such as thin

paneling to prevent the material from catching

between the bottom of the fence and the table.

– 20 –

Attach auxiliary fence to rip fence with two “C” clamps (Fig. GG)

Fig. GG

English

MAINTENANCE

MAINTAINING YOUR TABLE SAW

Fig. HH

GENERAL MAINTENANCE

WARNING

For your own safety, turn the switch OFF and remove the switch key. Remove the plug from the power source outlet before maintaining or lubricating your saw.

1. Clean out all sawdust that has accumulated inside the saw cabinet and the motor.

2. Polish the saw table with an automotive wax to keep it clean and to make it easier to slide the workpiece.

3. Clean cutting blades with pitch and gum remover.

4. A worn, cut, or damaged power cord should be replaced immediately.

WARNING

All electrical or mechanical repairs should be attempted only by a trained repair technician. Contact Hitachi

Authorized Service Center for service. Use only identical replacement parts. Any other parts may create a hazard.

5. Use liquid dish washing detergent and water to clean all plastic parts.

NOTE: Certain cleaning chemicals can damage plastic parts.

6. Avoid use of cleaning chemicals or solvents, ammonia and household detergents containing ammonia.

BLADE RAISING AND TILTING MECHANISM (FIG. HH)

After each five hours of operation, the blade raising mechanism and tilting mechanism should be checked for looseness, binding, or other abnormalities. With the saw dis-connected from the power source, turn the saw upside down and alternately pull upward and downward on the motor unit. Observe any movement of the motor mounting mechanism. Looseness or play in the blade raising screw (1) should be adjusted as follows:

1. Using a wrench, loosen nut (2).

2. Adjust nut (3) until it is finger-tight against the bracket

(4), then back off the nut (3) 1/6 turn.

3. Tighten nut (2) with the wrench, while holding nut (3)

in place. Maximum allowable play of screw rod (1) is

0.16” (4 mm).

4

3

2

1

5

Place a small amount of dry lubricant on the bevel gear

(2). The screw rod (1) must be kept clean and free of sawdust, gum, pitch, and other contaminants for smooth operations.

If excessive looseness is observed in any parts of the blade raising mechanism or tilting mechanism, contact

Hitachi Authorized Service Center immediately.

LUBRICATION

All motor bearings are permanently lubricated at the factory and require no additional lubrication.

On all mechanical parts of your table saw where a pivot or threaded rod are present, lubricate using graphite or silicone. These dry lubricants will not hold sawdust as would oil or grease.

– 21 –

English

TROUBLESHOOTING GUIDE

WARNING

To avoid injury from an accidental start, turn the switch OFF and always remove the plug from the power source before making any adjustments.

• Consult Hitachi Authorized Service Center if for any reason the motor will not run.

SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION

Saw will not start.

Does not make accurate 45° and 90° rip cuts.

Material pinched blade when ripping.

Material binds on splitter.

Saw makes unsatisfactory cuts.

Material kicked back from blade.

1. Saw not plugged in.

2. Fuse blown or circuit breaker tripped.

3. Cord damaged.

1. Positive stop not adjusted correctly.

2. Tilt angle pointer not set accurately.

1. Rip fence not aligned with blade.

2. Warped wood, edge against fence is not straight.

1. Plug in saw.

2. Replace fuse or reset circuit breaker.

3. Have cord replaced by Hitachi

Authorized Service Center.

1. Check blade with square and adjust positive stop.

2. Check blade with square and adjust to zero.

1. Check and adjust rip fence.

2. Select another piece of wood.

1. Splitter not aligned correctly with blade. 1. Check and align splitter with blade.

1. Dull blade.

2. Blade mounted backwards.

3. Gum or pitch on blade.

4. Incorrect blade for work being done.

5. Gum or pitch on blade causing erratic feed.

1. Rip fence out of adjustment.

2. Splitter not aligned with blade.

3. Feeding stock without rip fence.

4. Splitter not in place.

1. Replace blade.

2. Turn the blade around.

3. Remove blade and clean with turpentine and coarse steel wool.

4. Change the blade.

5. Clean table with turpentine and steel wool.

1. Align rip fence with miter gauge slot.

2. Align splitter with blade.

3. Install and use rip fence.

4. Install and use splitter. (with guard)

5. Dull blade.

5. Replace blade.

6. The operator letting go of material before 6. Push material all the way past saw it is past saw blade.

7. Miter angle lock knob is not tight.

blade before releasing work.

7. Tighten knob.

Blade does not raise or tilt freely.

Blade does not come up to speed.

1. Sawdust and dirt in raising/tilting

mechanisms.

1. Extension cord too light or too long.

2. Low house voltage.

1. Brush or blow out loose dust and dirt.

1. Replace with adequate size cord.

2. Contact your electric company.

Machine vibrates excessively. 1. Saw not mounted securely to workbench.

2. Bench on uneven floor.

3. Damaged saw blade.

1. Tighten all mounting hardware.

2. Reposition on flat level surface. Fasten to floor if necessary.

3. Replace blade.

Does not make accurate 45° and 90° crosscuts.

1. Miter gauge out of adjustment.

1. Adjust miter gauge.

– 22 –

PUSH STICK CONSTRUCTION

● This is a full-size drawing (actual size)

● Use good quality plywood or solid wood

● Use 1/2 in. or 3/4 in. material

● Push stick MUST be thinner than the width of material being cut

English

Drill Hole For

Hanging

Notch To Prevent

Hand From

Slipping

Cut Here To

Push 1/2 in.

Wood

Cut Here To

Push 3/4 in.

Wood

– 23 –

English

PARTS LIST

10” (255mm) JOBSITE TABLE SAW MODEL NO. C10FR

PARTS LIST FOR SCHEMATIC Always order by I.D. Number

Parts No. I.D.

726434

726437

326604

726438

726439

726440

726441

326546

326547

726443

726444

08VH CORD CLAMP

09JK

09WW GUARD BRACKET

0B23

0B24

0B27

0B2B

0B3R

Description

WRENCH

SADDLE

SPRING

POINTER BRACKET

NEEDLE POINTER

0B2D SWITCH BOX

0B3G ELECTROMAGNETIC DISTURBANCE UNITS

0B3H INSERT

WRENCH

Size QTY Parts No. I.D.

1

1

1

1

1

1

1

1

1

1

1

726587

726588

726589

726590

726596

726597

726600

726601

726603

726605

726612

0KJ4

0KJ5

Description

0KFG CR. RE. PAN HD. SCREW

0KHZ CAP HD. SQ.NECK BOLT

CAP HD. SQ.NECK BOLT

CAP HD. SQ.NECK BOLT

0KMR HEX. NUT

0KMS HEX. NUT

0KMV HEX. NUT

0KMW HEX. NUT

0KMY HEX. NUT

0KND HEX. NUT

0KQJ CROWN NUT

726445 0B84 WASHER

726446 0B99 SPACER

726447 0B9C PLUNGER HOUSING

726448 0B9P CLAMP

726449 0B9W BRACKET

726450 0BA4 SPACER

726451 0BA9 SPACER

726452 0BAA CLAMP

726453 0BAB SHIM

726454 0BAC SET NUT

726455 0BAE ARBOR COLLAR

726456 0BAT NUT

726457 0BAU SUPPORTING PLATE

726458 0BAX STIFFENER

726459 0BAY SCREW BAR

726460 0BAZ BEARING SEAT

726461 0BB1 SHAFT

726462 0BB2 PARRLE RING

756463 0BC2 LOCATION SEAT

326548 0F1H COLLAR

762466 0GD0 BLADE

726476 0J3U HEX WRENCH

726478 0J4F FLAT WASHER

726479 0J4H FLAT WASHER

726483 0J5L FLAT WASHER

726485 0J6T FLAT WASHER

726486 0J6U FLAT WASHER

726487 0J6V FLAT WASHER

726488 0J70 FLAT WASHER

726490 0J76 FLAT WASHER

726495 0J8D FLAT WASHER

726497 0J95 SPRING WASHER

726500 0JAA WASHER

726501 0JAE EXTERNAL TOOTH LOCK WASHER

726502 0JAF EXTERNAL TOOTH LOCK WASHER

726506 0JC9 SPRING PIN

726507 0JCA SPRING PIN

726513 0JED C-RING

726515 0JEY E-RING

726523 0JPB HEX. HD. BOLT

726534 0JX7 HEX. SOC. SET SCREW

726535 0JXL HEX. SOC. SET SCREW

726532 0K0Z HEX. HD. SCREW AND WASHER

726534 0K16 HEX. HD. SCREW AND WASHER

726538 0K25 HEX. SOCKET HD. CAP SCREWS

726543 0K3G CR. RE. PAN HD. SCREW & WASHER

726549 0K57 CR. RE. COUNT HD. SCREW

726557 0K7K CR. RE. ROUND WASHER HD. SCREW

726561 0K8C CR. RE.COUNT HD. TAPPING SCREW

726562 0K8D CR. RE.COUNT HD. TAPPING SCREW

726563 0K91 CR. RE. TRUSS HD. TAPPING SCREW

726566 0K9T HEX. HD. TAPPING SCREW

726567 0K9U HEX. HD. TAPPING SCREW

726570 0KA4 CR. RE. PAN HD. TAPPING SCREW

326437 0KBQ CR. RE. PAN HD. TAPPING SCREW

M5*0.8-20

M6*1.0-6

M10*1.5-12

M8*1.25-16

M8*1.25-16

M5*0.8-20

M5*0.8-12

M5*0.8-16

M6*1.0-12

M4*18-10

M4*18-16

M4*16-12

M5*16-16

M5*16-25

M4*16-16

M5*16-10

726575 0KCA CR. RE. TRUSS HD. TAPPING SCREW M5*12-12

726576 0KCH CR.RE. PAN HEAD TAPPING & WASHER SCREW M5*0.8-12

726577 0KCX CR. RE. PAN HD PLAIN WASHER TAPPING SCREW M5*0.8-10

726578 0KCY CR. RE. PAN HD PLAIN WASHER TAPPING SCREW M5*0.8-12

726581 0KDR CR. RE. PAN HD. SCREW

726582 0KDU CR. RE. PAN HD. SCREW

726585 0KF6 CR. RE. PAN HD. SCREW

M5*0.8-10

M6*1.0-12

M4*0.7-8

D=φ18

φ8*16-2.5

φ10*30-0.2

φ5*10-0.3

3/16*3/4-1/16

1 726666 216F SWITCH KEY

2 726668 21BN BRACKET GROUP ASS’Y

2 726695 237U COVER

1 726711 238S POINTER

1 726354 2771 ANGLE ROD

1 726759 275D EXTENTION WING

1

2

726760

726761

275E

275F

UPER TUBE

LOCATION SEAT

10 326606 275J BATTERY BOX ASS’Y

4 726762 275R LOCATION SEAT

3/16*1/2-3/64 1 726763 275U SPACER

3/16*3/8-0.022

8 726778 27QV DEFLECTOR

1/4*3/4-7/64

1/4*3/4-1/16

3/8*3/4-5/64

φ6

φ8

φ4

φ5

1 726615 0KQW LOCK NUT

1 726622 0KRX HEXAGON NUT AND FLAT WASHER

1 726625 0KSW STRAIN RELIEF

2 326453 0KTH STRAIN RELIEF

1 325733 0KUX TERMINAL

1 326428 0KVQ LEAD WIRE ASS’Y

2 326549 0LSF CIRCUIT BREAKER SWITCH

1 326458 0QQU CARBON BRUSH ASS’Y

1 326243 0QR0 BRUSH COVER

1 726642 0STE HEIGHT REGULATING BOLT ASS’Y

1 726644 0T00 SLIDING BASE ASS’Y

1 726649 10GP UPPER TUBE

1 326605 10GV POINTER

1 726345 2178 EXTENTION WING (RIGHT)

1 726657 20WQ HEX. HD. BOLT

1 726628 212M LEAD WIRE ASS’Y

M5*0.8 T=5

M6*1.0

M6*1.0-50

2 726782 287H RETAINING CLIP

4 726790 28FK TABLE

2 726796 28KX BODY SHELL

1 726799 28L9 LOCK KNOB

1 726802 28MC PARALLEL BRACKET ASS’Y

2 726803 28MD MITER GAUGE ASS’Y

1 726804 28MG HANDWHEEL ASS’Y

1 726805 28MH HANDWHEEL ASS’Y

2 726322 28N2 BATTERY

1 726812 28PA KNOB

1 326607 28W4 STICKER

2 326608 28W6 STICKER

4 326609 28W7 CAUTION LABEL

1 326610 28WA CAUTION LABEL

4 326611 28WB WARNING LABEL

1 326612 28WC WARNING LABEL

1 326613 28WD CAUTION LABEL

1 326614 28WG WARNING LABEL

1 326615 28WL WARNING LABEL

2 726861 28X4 BLADE GUARD ASS’Y

4 325772 28V2 HEX. WASHER HD. BOLT

2 726355 29E2 ROCKER SWITCH

4 726290 29PD WARNING LABEL

6 326616 2D8L FERRITE CORE

M6*1.0-16

8 726291 2DAU UPPER TUBE

2 326438 2FSM CR. RE. PAN HD PLAIN WASHER TAPPING SCREW M5*0.8-8

1 326552 2H05 POWER CABLE ASS’Y

2 326618 2HGW MOTOR

2 326619 2HKY RETAINING CLIP

4 326620 2HKZ SCALE

4 326621 2HL1 SCALE

1 326622 2HL2 SCALE

2 326623 2HL3 LABEL

2 326624 2HS2 BEVEL ANGLE ADJUSTMENT ASS’Y

Size

M5*0.8-12

M6*1.0-12

M6*1.0-35

M6*1.0-80

M5*0.8 T=4

M6*1.0 T=5

M10*1.5 T=8

M10*1.5 T=4

M8*1.25 T=6.5

M5*0.8 T=4 2

M8*1.25 T=12.5 2

1

1

3

1

1

1

QTY

2

2

1

1

1

1

1

1

1

1

1

1

2

2

1

2

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

2

2

1

1

1

1

1

1

1

1

1

1

2

1

2

1

1

2

2

1

1

2

2

3

– 24 –

10” (255mm) JOBSITE TABLE SAW

English

MODEL NO. C10FR

– 25 –

English

10” (255mm) JOBSITE TABLE SAW MODEL NO. C10FR

PARTS LIST FOR STAND

Parts No. I.D.

Description

726357 01AD WING NUT

726358 01AE LEVELING PAD

726477 0J4E FLAT WASHER

726482 0J4W FLAT WASHER

726503 0JAZ WAVE WASHER

Size QTY Parts No. I.D.

Description

1 726765 27DL HANDLE

φ6*13-1

1 726766 27DM BRACKET ASS’Y (RIGHT)

4 726767 27DV LEVELING PAD

φ8.2*18-1.5

4 726770 27DZ BRACKET ASS’Y (LEFT)

2 726356 27E6 HOOK

Size

726554 0K7D CR. RE. ROUND WASHER HD. SCREW M6*1.0-10

726559 0K7M CR. RE. ROUND WASHER HD. SCREW M6*1.0-18

726580 0KDJ CR. RE. PAN HD. SCREW

726581 0KDR CR. RE. PAN HD. SCREW

M5*0.8-12

M5*0.8-10

2 726779 27RQ CAP HD. SQ.NECK BOLT

1 726780 27RR CR. RE. TRUSS HD. SCREW

2 726783 288R HEX. HD. BOLT

4 726784 28BU FLOOR PLATE

M8*1.25-40 4

M6*1.0-46 4

M8*1.25-55 4

1

726594 0KKU CR. RE. PAN HD. ROUND NECK SCREW M5*08-10

726597 0KMS HEX. NUT M6*1.0 T=5

1

1

726785 28BX CR. RE. PAN HD PLAIN WASHER TAPPING SCREW

726797 28L2 CLAMP HANDLE

M5*0.8-10 4

4

726610 0KQ4 WING NUT M8*1.25

1 726798 28L3 FOLLOWER PLATE 1

QTY

1

1

1

1

3

726615 0KQW LOCK NUT

726616 0KQX NUT

726617 0KQY LOCK NUT

726665 213T ROLLING WHEEL

726673 22FZ CAP HD. SQ.NECK BOLT

726764 27DJ FOAM

M5*0.8 T=5 7 726831 28VU HOOK

M6*1.0 T=6 4 726832 28VV CONNECTOR

M8*1.25 T=8 6 726833 28VX SUPPORTING TUBE ASS’Y

2 726834 28VZ LEVELING PAD

M8*1.25-45 2 326617 2GRX DUST COLLECTOR ASS’Y

1 726809 2EKG DUST BAG

1

1

2

1

1

1

– 26 –

– 27 –

English

English

Issued by

Hitachi Koki Co., Ltd.

Shinagawa Intercity Tower A, 15-1, Konan 2-chome,

Minato-ku, Tokyo 108-6020, Japan

– 28 –

607

Code No. C99135011

Printed in Taiwan