congratulations on owning your new nautica

congratulations on owning your new nautica
CONGRATULATIONS ON OWNING YOUR NEW NAUTICA WATCH
DEVELOPED FROM ADVANCED ELECTRONICS TECHNOLOGY,
THE MOVEMENT IS MANUFACTURED FROM THE BEST QUALITY
COMPONENTS AND POWERED BY A LONG LIFE BATTERY.
NAUTICA watches have been developed with the highest attention to
quality, function and detail, as befits the NAUTICA tradition.
Please read the following instructions carefully to fully understand all
of the functions of your finely crafted timepiece.
WATER-RESISTANCE
If your watch is water-resistant, it will be indicated on the watch face
or on the caseback.
• 50 Meter Water-Resistant watch withstands water pressure to 86p.
s.i.a. (equals immersion to 164 feet or 50 meters below sea level)
and dust as long as crystal, crown and case remain intact.
• 100 Meter Water-Resistant watch withstands water pressure to
160p.s.i.a. (equals immersion to 328 feet or 100 meters below sea
level) and dust as long as crystal, crown and case remain intact.
• 200 Meter Water-Resistant watch withstands water pressure to
INDIGLO® NIGHT-LIGHT
If your watch has “INDIGLO” on the dial, your watch is equipped with
the INDIGLO Night-Light. To activate this feature, depress the crown or
the pusher on the left side of the watch to illuminate the entire dial for
easy reading during nighttime or low light conditions. Light will appear
immediately.
Your NAUTICA watch featuring INDIGLO Night-Light contains a
patented electroluminescent technology (U.S. Patent Number 4,527,96
and 4,775,964). The INDIGLO Night-Light illuminates the entire watch
lens with a uniform bright light that offers superior readability in all low
light and nighttime conditions. Simply press the appropriate button to
activate.
WARNING: DO NOT PRESS THE BUTTON UNDER WATER AS THE
WATCH WILL NOT RETAIN WATER RESISTANCE.
INDIGLO is a registered trademark of Indiglo Corporation.
320p.s.i.a. (equals immersion to 656 feet or 200 meters below sea
level) and dust as long as crystal, crown and case remain intact.
NOTE: CROWN MUST BE SCREWED INTO THE CASE
PROTRUSION TO ASSURE WATER RESISTANCE.
Battery
Battery contains small amount of mercury. Please recycle or dispose of
properly.
SCREW-IN SETTING CROWN
ATTENTION
This is a screw down crown
Do not pull
Please read instruction
booklet before operation
ELAPSED TIME RING
If your watch is equipped with a rotating outer dial with numbers and
indicators, this Elapsed Time Ring may be used to indicate the length
of time remaining for an activity or the starting time of an activity.
TIME REMAINING - set the outer ring so that the triangle is pointing
to the time the activity is to end.
STARTING TIME - set the triangle on the time the activity is to begin.
TACHYMETER
SCREW-IN SETTING CROWN STICKER
Some deep-depth water-resistant watches require the setting crown to
be screwed in to ensure water-resistancy. If your Nautica watch has a
transparent sticker at back of the case back (diagram above) please
unscrew the crown before setting your watch, and the crown must be
screwed in after setting the watch.
To screw in, push in the crown firmly against the thread protrusion and
hold it in while turning the crown clockwise. Continue to screw in the
crown light until it is tight .
A tachymeter measures the speed at which the wearer has traveled
over a measured distance, i.e., a measured mile on the highway. For
example, start the chronograph when you pass the starting point and
stop it when you pass the finish point. You can then read your speed
in units per hour off the tachymeter scale.
BAND ADJUSTMENT
To disconnect band from clasp, press in end of spring bar
(use pin or small paper clip) and separate link band from
clasp as illustrated.
To reassemble band to clasp, place spring bar in band and place end of
spring bar into desired hole in clasp. Press opposite end of spring bar in
and slide into clasp and position so tip snaps into corresponding hole.
Date Models
BASIC Models
Date
Date
AB
AB
ABC
ABC
crown position
crown position
crown
position
crown
position
DAY
Y121, 2039, 2036, 608/1010
VX10 / VX51 / YL60 / 4S20
TIME
To set the time:
TIME
To set the time:
1.
2.
3.
VX33
VX12 / VX42 / VX32 / VX82 / 2315 / 2115 / 2415 / AL32
Pull crown to “B” position.
Turn crown clockwise /
counter clockwise to correct time.
Push crown to “A” position.
AB
crown
position
336/168
6
1. Pull out crown to “C” position.
2. Turn crown clockwise / counter clockwise to correct time.
3. Push in crown to “A” position.
CALENDAR
To set the calendar/date:
1. Pull out crown to “B” position.
2A.Turn crown clockwise / counter clockwise to correct date.
2B.Turn crown counter clockwise to correct date. (For VX33 only)
3. Push in crown to “A” position.
NOTE:The date changes automatically every 24 hours.
7
Multi Models
DATE
TIME
To set the time:
1. Pull crown to “C” position.
2. Turn crown either way to correct time.
3. Push crown to “A” position.
crown
position
DAY
24 HOUR
DATE
To set the date:
1. Pull crown to "C" position.
2. Advance time 24 hours to change the day.
3. Push crown to "A" position.
Note: 24 hour indicator can be changed only when setting the time.
24 HOUR
DAY
ABC
ABC
crown
position
crown
position
DATE
VX3R
VX3N / VX7N
DAY
DATE
DAY
VX36
8
VX3L
24 HOUR
24 HOUR
ABC
crown
position
DAY
VX3J
Note: the date changes automatically every 24 hours.
1. Pull crown to “B” position.
2. Turn crown to correct date.
3. Push crown to “A” position.
DAY OF WEEK (for VX3J / VX3L / VX3N / VX36 / VX7N / VD79)
To set the day:
DATE
ABC
ABC
ABC
crown
position
crown
position
DATE
VD79
9
DATE
TIME
To set the time:
Indiglo models
DATE
1. Pull crown to “C” position.
2. Turn crown either way to correct
time.
3. Push crown to “A” position.
ABC
DATE
To set the date :
Date
crown
position
DAY
ABC
24 HOUR
crown position
6P27
1. Pull crown to “B” position.
2. Turn crown counter clockwise to
correct date.
3. Push crown to “A” position.
Note: The day changes automatically
every 24 hours.
DATE
ABC
crown
position
DAY OF WEEK (for 6P27 / 6P29)
To set the day:
24 HOUR
6P23
1. Pull crown to “C” position.
2. Turn crown clockwise (hour hands
rotate 24 hours) to correct day of
week.
3. Push crown to “A” position.
Note: The day of week changes
automatically every 24 hours.
DATE
Day
ABC
crown
position
24 HOUR
6P29
10
M905
To activate the Indiglo:
Press crown to indicate Indiglo night light.
TIME
To set the time:
1. Pull crown to "C" position.
2. Turn crown clockwise / counter clockwise to correct time.
3. Push crown to "A" position.
CALENDAR
To set the date:
1.
2.
3.
Pull crown to "B" position.
Turn crown counter clockwise or towards you to correct date.
Push crown to "A" position.
Note: The date changes automatically every 24 hours.
11
This Chronograph watch has three functions:
Chronograph models
TIME, CALENDAR, STOPWATCH
minute hand
Permanent second hand
PUSHER “A”
ABC
Crown Position
stopwatch second hand
PUSHER “B”
stopwatch munute hand
1. Pull crown to position “C”.
2. Turn crown clockwise / counter clockwise to correct time.
3. Push crown to position “A”.
CALENDAR
To set the calendar:
1. Pull crown to position “B”.
2. Turn crown clockwise to correct calendar.
3. Push crown to position “A”.
Date
YM12 / YM1G
STOPWATCH
This stopwatch is capable of measuring:
StopWatch 1/20sec. hand
PuSHER “A”
Small Second hand
ABC
CROWN POSITION
STOPWATCH SECOND HAND
Stopwatch Hour hand
TIME
To set the time:
– 1/5 second elapsed up to 60 minutes.
– After 60 minutes, it will start counting again from “0” repeatedly up to 12 hours.
Before using the stopwatch, reset the stopwatch hands.
To the “12” and “0” position.
STANDARD STOPWATCH MEASUREMENT:
Stopwatch Minutes hand
YM92
12
1. Press pusher “A” to start timing.
2. Press pusher “A” to stop timing.
3. Press pusher “B” to reset.
13
ACCUMULATED ELAPSED TIME MEASUREMENT:
1.
2.
3.
4.
5.
Press pusher “A” to start timing.
Press pusher “A” to stop timing.
Press pusher “A” to restart timing.
Press pusher “A” to stop 2nd timing.
Press pusher “B” to reset.
4. Press pusher “A” again for 2 seconds, the stopwatch second hand turns a full
cycle.
5. Press pusher “B” repeatedly to set stopwatch second hand to “0” position.
6. Push crown to position “A”.
Remarks:
Example of using split time measurement for two runners.
Two runners can be timed simultaneously; the first runner’s time can be recorded
while the second runner’s time will continue to be accumulated until he finishes.
SPLIT TIME MEASUREMENT:
1. Press pusher “A” to start the timing of the first runner.
2. Press pusher “B” to stop and record the timing of the first runner. (Once pusher
B is activated, even though the stopwatch 1/20 sec. hand and the big stopwatch
sec. hand stop on the dial, the stopwatch still continues to time internally.)
3. Press pusher “B” to start the timing of the second runner. The stopwatch sec.
hand will jump to show internal accumulated time and to carry on timing of the
second runner.
4. Press pusher “A” to stop the timing of the second runner and record the time.
5. Press pusher “B” for third time to reset, all stop watch hands will return to 12
o’clock position.
TO ADJUST STOPWATCH HAND (for YM12 / YM1G) :
1. Pull crown to position “C”.
2. Press pusher “A” for 2 seconds, the stopwatch minute hand turns a full cycle.
3. Press pusher “B” repeatedly to set stopwatch minute hand to “0” position.
14
This is suggested to check the hour and minute hands to ensure they are correct
before pushing the crown back to position “A”
TO ADJUST STOPWATCH HAND (for YM92) :
1. Pull crown to “C” position.
2. Press pusher “A” for 2 seconds.
3. Press pusher “B” to “0” setting for the 1/20 sec. hand. If the hand is not at “0” or
“12” position, then, press pusher “B” repeatedly, until the hand moves by each
intervaI and returns to “0” or “12” position.
4. Press pusher “A” for 2 seconds.
5. Press pusher “B” to “0” setting for the stopwatch sec. hand. If the hand is not at “0”
or “12” position, then, press pusher “B” repeatedly, until the hand moves by each
intervaI and returns to “0” or “12” position.
6. Press pusher “A” for 2 seconds.
7. Press pusher “B” to “0” setting for the stopwatch min. / hour hand. If the hand is
not at “0” or “12” position, then, press pusher “B” repeatedly, until the hand moves
by each intervaI and returns to “0” or “12” position.
8. Push crown to “A” position after the adjustments of all stopwatch hands.
Note: Please make sure that the stopwatch is stopped and reset before adjusting.
15
minute hand
24-hour hand
stopwatch munute hand
PUSHER “A”
ABC
hour hand
Crown Position
stopwatch second hand
second hand
PUSHER “B”
calender
FS00 / FS01
hour hand
minute hand
24-hour hand
PUSHER “A”
ABC
stopwatch munute hand
Crown Position
PUSHER “B”
stopwatch second hand
second hand
FS20 / FS21
calender
This Chronograph watch has 3 functions:
TIME, CALENDAR, STOPWATCH
TIME
To set the time:
1. Pull crown to position “C”.
2. Turn crown clockwise / counter clockwise to correct time.
3. Push crown to position “A”.
16
CALENDAR
To set the calendar:
1. Pull crown to position “B”.
2. Turn crown clockwise to correct calendar.
3. Push crown to position “A”.
STOPWATCH
The stopwatch is capable of measuring and displaying 1/1 second unit up to
maximum 1 hour. The stopwatch minute hand synchronizes with the stopwatch
second hand.
1. Press pusher “A” to start timing.
2. Press pusher “A” again to stop timing.
3. Press pusher “B” to reset.
CORRECTING STOPWATCH HANDS
If after resetting the stopwatch hands it is found that they are not at the '12' or '0'
position, correct them as follows:
1. Pull crown to “ C” position.
2. Press pusher “A” continuously, the stopwatch hand will advance rapidly until it
gets close to the “ 12” position. Then, press pusher “A” repeatedly, the stopwatch
hand will move by intervals until it returns to “12” position.
3. Push crown back to “A” position.
4. Press pusher “A” to activate the stopwatch hand.
5. Press pusher “B” reset the stopwatch minute hand at 10 o’clock until it returns to
“0” position.
17
Permanent second hand
minute Chrono hand
PUSHER “A”
ABC
STOPWATCH second hand
Crown Position
PUSHER “B”
Hour Chrono hand
5030D
DATE
DATE
Permanent second hand
minute Chrono hand
PUSHER “A”
ABC
STOPWATCH second hand
Crown Position
PUSHER “B”
1/10 second counter hand (Hour
counter hand after 30 minutes)
5040B
18
This Chronograph watch has 3 functions:
TIME, CALENDAR, STOPWATCH
TIME
To set the time:
1. Pull crown to position “C”.
2. Turn crown clockwise / counter clockwise to correct time.
3. Push crown back to position “A”.
Calendar
To set the calendar:
1. Pull crown to position “B”.
2. Turn crown clockwise to correct calendar.
3. Push crown back to position “A”.
STOPWATCH
This stopwatch is capable of measuring:
Chrono Hours elapsed up to 12 hours. ( 6 o,clock eye) (For 5030D)
Chrono Hours elapsed up to 10 hours. (6 o'clock eye) (For 5040B)
Chrono Minutes elapsed up to 30 minutes. ( 9 o,clock eye )
Stopwatch Second up to 1 minute. ( Big second hand )
Before using the stopwatch, reset stopwatch chrono hands to the “12” and “0”
position.
Standard Stopwatch Measurement
1. Press pusher “A” to start timing.
2. Press pusher “A” again to stop timing.
3. Press pusher “B” to reset.
19
Accumulated Elapsed Time Measurement
1.
2.
3.
4.
5.
Press pusher “A” to start timing.
Press pusher “A” again to stop timing.
Press pusher “A” to restart timing.
Press pusher “A” again to stop second timing.
Press pusher “B” to reset.
split time Measurement
Example of using split time measurement for two runners. Two runners can be timed
simultaneously; the first runner’s time can be recorded while the second runner’s
time will continue to be accumulated until he finishes.
1. Press pusher “A” to start the timing of the first and second runner.
2. Press pusher “B” to stop and record the timing of the first runner.
(Once pusher “B” is activated, even though the chrono minute hand and the
big stopwatch sec. hand stop on the dial, the stopwatch still continues to run
internally.)
3. Press pusher “B” to catch up the timing of the second runner. The stopwatch sec.
hand will jump to show internal accumulated time and to carry on timing of the
second runner.
4. Press pusher “A” to stop the timing of the second runner and record the time.
5. Press pusher “B” for third time to reset, all stopwatch chrono hands will return to
“12” and “0” position.
Corrective Mode for Stopwatch Chrono Hands
1. Pull crown to position “C”.
2. Press pushers “A” and “B” simultaneously for at least 2 seconds.
3. The big stopwatch sec hand rotates by 360 degree to activate corrective mode.
20
To adjust the Big sec. Stopwatch hand
If it is not located at “12” or “0” position, either press pusher “A” continuously or
repeatedly until the hand moves by each interval and returns to “12” and “0” position.
After finishing the big sec. stopwatch hand adjustment, press crown back to position
“A” to terminate the adjustment.
TO ADJUST THE 1/10 SECOND COUNT HAND (FOR 5040B)
After activating the corrective mode, if the 1/10 second counter hand is not located at
'12' or '0' position, press pusher “B” once to activate the corrective mode of the 1/10
second counter hand. Press pusher “A” continuously or repeatedly until the hand
moves by each interval and returns to “12” and “0” position.
Press crown back to position “A” to terminate the adjustment.
To adjust the Hour chrono hand (for 5030D)
After activating the corrective mode, if the hour chrono hand is not located at '12' or
'0' position, press pusher “B” once to activate the corrective mode of the hour chrono
hand. Press pusher “A” continuously or repeatedly until the hand moves by each
interval and returns to “12” and “0” position.
Press crown back to position “A” to terminate the adjustment.
To adjust the Minute chrono hand
After activating the corrective mode, if the minute chrono is not located at '12' or '0'
position, press pusher “B” twice to activate the corrective mode of the minute chrono hand.
Press pusher “A” continuously or repeatedly until the hand moves by each interval
and returns to “12” and “0” position.
Press crown back to position “A” to terminate the adjustment.
Once finished adjusting all stopwatch chrono hands, press crown back to “A” position
to terminate adjustment.
21
This Chronograph watch has three functions:
TIME, CALENDAR, STOPWATCH
24 hour Disk
24 hour hand
stopwatch
minute hand
PUSHER “A”
stopwatch
second hand
stopwatch
minute Disk
ABC
Crown
Position
Crown
Position
stopwatch
second hand
PUSHER “B”
DATE
second hand
PUSHER “A”
ABC
second hand
OS20
PUSHER “B”
OS2B
DATE
TIME
To set the time:
1. Pull crown to position "C".
2. Turn crown clockwise / counter clockwise to correct time.
3. Push crown to position "A".
CALENDAR
To set the calendar:
1. Pull crown to position "B".
2. Turn crown counter-clockwise to set calendar.
3. Push crown to position "A".
STOPWATCH
Stopwatch
minute hand
Minutes hand
Minutes hand
hour hand
stopwatch
second hand
permanent
second hand
ABC
ABC
Crown
Position
Stopwatch
minute hand
PUSHER “B”
OS11
24 hour hand
PUSHER “A”
PUSHER “A”
hour hand
The stopwatch is capable of measuring and displaying time in 1/1 second united up
to a maximum of 59 minutes 59 seconds.
stopwatch
second hand
Date
22
Crown
Position
PUSHER “B”
OS21
date
1. Press pusher "A" to start timing.
2. Press pusher "A" again to stop timing.
3. Press pusher "B" to reset.
CORRECTING STOPWATCH HAND
If after resetting the stopwatch second hand it is found that they are not at the '12' or
'0' position, correct as follows:
1. Pull crown to "C" position.
2. Press pusher “A” continuously, the stopwatch second hand will advance rapidly
until it gets close to the “12” position. Then, press pusher “A” repeatedly, the
stopwatch second hand will move by intervals until it returns to “12” position.
3. Push crown to position “A".
23
This Chronograph watch has 3 functions:
TIME, CALENDAR, STOPWATCH
24-hour hand
Stopwatch minute hand
PUSHER A
ABC
Crown Position
PUSHER “B”
stopwatch second hand
VD53
DatE
TIME
To set the time:
1. Pull crown to position “C”.
2. Turn crown clockwise / counter clockwise to correct time.
3. Push crown to position “A”.
CALENDAR
To set the calendar:
1. Pull crown to position “B”.
2. Turn crown clockwise to correct calendar.
3. Push crown to position “A”.
STOPWATCH
The stopwatch is capable of measuring:
stopwatch second hand
PUSHER A
ABC
Crown Position
PUSHER B
Stopwatch minute hand
VD51
24
DatE
1 minute elasped up to 60 minutes.
Before using the stopwatch, reset the stopwatch hands to the “12” & “0” position.
STANDARD STOPWATCH MEASUREMENT:
1. Press pusher “A” to start timing.
2. Press pusher “A” to stop timing.
3. Press pusher “B” to reset.
split time Measurement
Example of using split time measurement for two runners. Two runners can be timed
simultaneously; the first runner’s time can be recorded while the second runner’s time will
continue to be accumulated until he finishes.
25
1. Press pusher “A” to start the timing of the first and second runner.
2. Press pusher “B” to stop and record the timing of the first runner.
(Once pusher “B” is activated, even though the chrono minute hand and the
big stopwatch sec. hand stop on the dial, the stopwatch still continues to run
internally.)
3. Press pusher “B” to catch up the timing of the second runner. The stopwatch sec.
hand will jump to show internal accumulated time and to carry on timing of the
second runner.
4. Press pusher “A” to stop the timing of the second runner and record the time.
5. Press pusher “B” for third time to reset, all stopwatch chrono hands will return to
“12” and “0” position.
TO ADJUST STOPWATCH HAND
1. Pull crown to position "C".
2. Press pusher "A" continuously or repeatedly to adjust the stopwatch second hand
to "0" or "12" position.
3. Press pusher "B" continuously or repeatedly to adjust the stopwatch minute hand
to "0" or "12" position.
4. Push back the crown to position "A".
Permanent Second Hand
Stopwatch Minute
Hand
PUSHER A
ABC
Stopwatch Second Hand
Crown Position
DatE
PUSHER B
8171/201
Permanent Second Hand
Stopwatch Minute Hand
PUSHER A
Stopwatch Second Hand
ABC
Crown Position
PUSHER B
DatE
8171/202
DatE
Permanent Second Hand
Stopwatch Minute Hand
PUSHER A
ABC
Stopwatch Second Hand
Crown Position
PUSHER B
Day
8172/220
26
27
DatE
This Chronograph watch has 3 functions:
TIME, CALENDAR, STOPWATCH
Before using the stopwatch, reset the stopwatch hands to the “12” & “0” position.
STANDARD STOPWATCH MEASUREMENT:
TIME
To set the time:
1. Pull crown to position “C”.
2. Turn crown clockwise / counter clockwise to correct time.
3. Push crown to position “A”.
CALENDAR
To set the calendar:
1. Pull crown to position “B”.
2. Turn crown clockwise to correct calendar.
3. Push crown to position “A”.
DAY OF WEEK (For 8172/220)
To set the day:
1. Pull crown to “C” position.
2. Turn crown clockwise (hour hands rotate 24 hours) to correct day of week.
3. Push crown to “A” position.
Note: The day of week changes automatically every 24 hours.
1. Press pusher “A” to start timing.
2. Press pusher “A” to stop timing.
3. Press pusher “B” to reset.
SPLIT TIME MEASUREMENT:
1. Press pusher “A” to start timing.
2. Press pusher “B” to split.
3. Press pusher “B’ to begin again.
4. Press pusher “A’ to stop.
5. Press pusher “B’ to reset.
TO ADJUST STOPWATCH HAND:
1. Pull crown to position "B".
2. Press pusher "A" continuously or repeatedly to adjust the stopwatch second hand
to "0" or "12" position.
3. Press pusher "B" continuously or repeatedly to adjust the stopwatch minute hand
to "0" or "12" position.
4. Push back the crown to position "A".
STOPWATCH
The stopwatch is capable of measuring:
1. 1 minute elasped up to 30 minutes.
2. Chronograph hand 1/5 second.
28
29
stopwatch minute
hand
Date
ABC
stopwatch hour
hand
Crown Position
PUSHER B
stopwatch second
hand
OS62
second hand & 1/20 second
stopwatch hand
STOPWATCH
This stopwatch is able to measure and display time in 1/20 ( 1/1) second united up
to max 11 hrs 59 min 59 sec.
The retrograde stopwatch 1/20 ( 1/1) second hands keeps continuously running for
60 seconds after starting, and then stops at "0" position.
1. Press pusher "B" to enter the chrono mode.
2. Press pusher "A" to start timing.
3. Press pusher "A" again to stop timing.
4. Press pusher "B" to reset.
Note: Motion of the retrograde stopwatch is a demo. Actual measurement will be shown
when it stopped while "stop" button is pressed.
This Chronograph watch has three functions:
TIME, CALENDAR, STOPWATCH
TIME
To set the time:
1. Pull crown to position "C" , the small hand at 6 o'clock returns to "60" position.
2. Turn crown clockwise to correct time.
3. Push crown to position "A", the small hand at 6 o'clock begins to run.
CALENDAR
To set the date:
Correct the stopwatch hands
If after resetting the stopwatch hands it is found that they are not at the '12' or '0'
position, correct them as follows:
1.
2.
3.
4.
Pull crown to position "B".
Press pusher "A" to set the stopwatch second hand to the "0" position.
Press pusher "B" to set the stopwatch 1/20 second hand to the "0" position.
The stopwatch hands can be advanced rapidly by continuously pressing pushers
"A' or "B".
5. Once the hands return to "0" position, reset time and push crown to position "A".
1. Pull crown to position "B".
2. Turn crown counter clockwise to correct date.
3. Push crown to position "A".
30
31
24 hour hand
stopwatch minute hand
PUSHER A
AB
Crown Position
PUSHER B
second hand
JS00
stopwatch second hand
This Chronograph watch has two functions:
TIME, STOPWATCH
TIME
To set the time:
STOPWATCH
This stopwatch is able to measure and display time in 1 second intervals up to max
29 min 59 sec.
It will stop automatically after running continuously for 30 minutes.
1. Press pusher "A" to start timing.
2. Press pusher "A" again to stop timing.
3. Press pusher "B" to reset.
Correcting the stopwatch hands:
If after resetting the stopwatch hands it is found that they are not at the '12' or '0'
position, correct them as follows:
1. Pull crown to position "B".
2. Press pusher "A" to set the stopwatch second hand to the "0" position.
3. The stopwatch minute hand is synchronized with the stopwatch second hand and
the second hand can be advanced rapidly by continuously pressing pusher "A".
4. Once the hands return to "0" position, reset time and push crown to position "A".
1. Pull crown to position "B".
2. Turn crown clockwise to correct time.
3. Push crown to position "A", the second hand begins to run.
32
33
day hand
PUSHER A
stopwatch minute
hand
ABC
Crown Position
stopwatch second
hand
second hand
PUSHER B
FS60 / FS61
This Chronograph watch has four functions:
TIME, CALENDAR, DAY OF WEEK, STOPWATCH
TIME
To set the time:
Date
DAY
To set the day:
1. Pull crown to position "B".
2. Turn crown counter clockwise to correct day.
3. Push crown to position "A".
STOPWATCH:
This stopwatch is able to measure and display time in 1 second intervals up to max
59 min 59 sec.
After elapsed for 59 min. 59 sec, the stopwatch second hand resumes timing from 0
second, the stopwatch minute hand continues and accumulates timing of stopwatch
until it is stopped by pressing pusher "A".
1. Press pusher "A" to start timing.
2. Press pusher "A" again to stop timing.
3. Press pusher "B" to reset.
Correcting the stopwatch hands
1. Pull crown to position "C".
2. Turn crown clockwise to correct time.
3. Push crown to position "A".
If after resetting the stopwatch second hand it is found that they are not at the '12' or
'0' position, correct it as follows:
1. Pull crown to position "C".
2. Press pusher "A" continuously, the stopwatch second hand will advance rapidly
until it gets close to “0” position.
3. Press pusher “B” to check that all stopwatch hands have been reset to "0" position.
4. Press pusher "B" to check all stopwatch hands has been reset to "0" position.
CALENDAR
To set the date:
1. Pull crown to position "B".
2. Turn crown clockwise to correct date.
3. Push crown to position "A".
34
35
minute hand
4th center hand
PUSHER A
Upper hand
date
ABC
Chrono hours /
2nd time zone
hour hand
Crown Position
chrono minutes scale
PUSHER B
second hand
Lower hand
M363
STOPWATCH
This stopwatch is capable of measuring and displaying 1/5 second up to maximum 4
hours.
1. Press pusher “A” to start the timing.
2. Press pusher “A” again to stop the timing.
3. Press pusher “B” to reset.
Note
– Press and hold pusher “B” anytime to restart the timing, the hand will start
running again after release the pusher “B”.
– The upper hand will move to “0” after reset the timing, the watch will return to
display second time zone after eight seconds.
This Chronograph watch has 3 functions:
SECOND TIME ZONE
TIME
To set the time:
To set the Second Time Zone:
TIME, CALENDAR, STOPWATCH
1. Pull crown to position ”C”
2. Turn crown clockwise / counter clockwise to correct the time.
3. Push crown back to position “A”.
CALENDAR
To set the Calendar:
1. Pull crown to position ”B”
2. Turn crown counter clockwise to correct the calendar.
3. Push crown back to position “A”.
36
The upper hand shows the time for the second time zone and the scale is 24 hours.
1. Pull crown to position “B”. The 4th centre hand will display the minutes of the
second time zone.
2. Press pusher “A” to set the hour of second time zone.
3. Press pusher “B” to set the minutes.
4. Push crown back to position “A”.
4th CENTRE HAND ADJUSTMENT
1. Pull crown to position “C”. The upper and lower hand will reset to “0”
automatically.
2. Press pusher “A” or “B” to adjust the 4th centre hand to “12” position.
3. Push back the crown to position “A”.
37
analog and digital Models
ANALOG TIME
To set the time:
1. Pull out the crown and turn clockwise or counter clockwise to correct the time.
2. Push the crown in after complete setting.
start / stop
SET / indiglo
crown
lap / reset
mode
M12-1515
This Analog and Digital watch has 6 function:
Analog and digital time display / Auto calendar 2000-2099 / Two time zones / Two
daily alarms linked to time zone / Three linked countdown timers / Chronograph with
42-lap memory / Indiglo Night Light.
BASIC OPERATION
1. In TIME mode, press and hold START/STOP to shut off digital display. Press
once to turn back on.
2. Press SET/INDIGLO to illuminate watch face.
3. Press MODE to cycle through CHRONO, RECALL, TIMER, ALARM and TIME
modes. Press and hold MODE in any mode to return to TIME display.
4. When setting digits, press START/STOP to go forward or LAP/RESET to go
backward or hold to change rapidly.
38
DIGITAL TIME AND CALENDAR
To set the time and calendar:
1. Press MODE until TIME appears. Press and hold SET/INDIGLO to begin setting
time.
2. Press START/STOP or LAP/RESET to set SECONDS to 0.
3. Press MODE to select HOURS digits.
4. Press START/STOP or LAP/RESET to advance. Go through 12 hours for AM or
PM.
5. Press MODE to select MINUTES, YEAR, MONTH, DAY, DAY of WEEK, 12 or 24
time display, MONTH-DAY or DAY-MONTH date display. Press START/STOP or LAP/
RESET to advance selected item.
6. Press SET/INDIGLO when done.
7. Press and hold LAP/RESET and wait for beep to change display to second TIME
ZONE. Repeat above to set time.
Note: once date is set, calendar runs automatically.
CHRONOGRPAH
1. Press MODE until CHRONO appears. Watch will briefly display available storage
(1-42).
2. Press START/STOP to start CHRONO.
3. Press LAP/RESET to take a lap. Display of running time resumes after 5
seconds.
4. Press START/STOP to stop timing. Press again to resume.
39
5. While CHRONO is stopped, press MODE to enter RECALL mode. Press START/
STOP repeatedly to recall stored lap and split times.
6. Press and hold LAP/RESET to clear stored times. Chrono will automatically clear.
OR
7. In RECALL mode, press and hold LAP/RESET to reset and stored laps/splits will
automatically clear.
7. Press START/STOP to start or stop LOOP TIMER.
8. With TIMER stopped, press and hold SET/INDIGLO to reset all LOOPS to zero.
At end of timed LOOP, next LOOP TIMER starts. Cycle is continuous for up to 30
loops.
ALARM
1.
2.
3.
4.
COUNTDOWN TIMER
1. Press MODE until TIMER appears. Press LAP/RESET to select LOOP 1, 2 or 3.
Timers will count upwards starting with last LOOP TIMER set, unless last LOOP
TIMER set is 3 (timers will then count backwards from LOOP 3).
2. Press and hold SET/INDIGLO to set LOOP TIMER. Press START/STOP or LAP/
RESET to set seconds.
3. Press MODE to select MINUTES, press START/STOP or LAP/RESET to set
minutes.
4. Press MODE and then START/STOP or LAP/RESET to select next LOOP.
5. Repeat above steps to set each additional LOOP.
6. Press SET/INDIGLO when done.
40
Press MODE until ALARM appears.
Press LAP/RESET to select ALARM 1 or 2.
Press and hold SET/INDIGLO to set.
Press START/STOP or LAP/RESET to set HOURS. Go through 12 hours for AM
or PM.
5. Press MODE to select MINUTES, press START/STOP or LAP/RESET to set.
6. Press MODE to select TIME ZONE for alarm, press START/STOP or LAP/RESET
to set.
7. Repeat to select MONTH and DAY. Leave blank for daily alarm.
8. Press SET/INDIGLO when done.
9. Repeat for second ALARM.
10.Press START/STOP to turn ALARM on or off.
) will appear in TIME display when ALARM is armed for that
Alarm symbol (
TIME ZONE.
Beep will sound when ALARM time is reached. Press any button to silence alarm.
INDIGLO @ NIGHT LIGHT
Press SET/INDIGLO to illuminate watch face. Patented (U.S. pat. 4,527,096
and 4,775,964) electroluminescent technology used in the INDIGLO® night-light
illuminates entire watch face at night and in low light conditions.
41
start / stop
light
crown
set
mode
MW36
DIGITAL TIME AND CALENDAR
To set the time and calendar:
1.
2.
3.
4.
5.
6.
Press “Mode” button until time mode appears.
Press and hold “Set” button to begin setting time.
Press “Mode” button to select the setting item in the order,
Second ➞ Minute ➞ Hour ➞ Time Format ➞ Month ➞ Date ➞ Day of Week
Press “Start/Stop” button to set the timing follow the order.
Press and hold the “Start/Stop” button, the timing will cause repaid increment.
Press “Set” button to exit the time setting.
DUAL TIME
This Digital watch has 7 functions
Analog and Digital Time display / Dual Time / Calendar / Chronograph / Timer /
Alarm / Electroluminescent backlight
MODE SELECTION
Press “Mode” button to cycle through “TIME”, “ALARM”, ”CHRONOGRAPH” and
“TIMER” mode.
ANALOG TIME
To set the time:
1. Pull out the crown and turn clockwise or counter clockwise to correct the time.
2. Push the crown in after complete setting.
42
1.
2.
3.
4.
5.
6.
Press “Start/Stop” button to display the dual time under time mode.
Press and hold “Set” button to begin setting time.
Press “Mode” button to select the hour or minute for setting.
Press “Start/Stop” button to set the hour or minute.
Press “Set” button after timing is completed.
Press “Start/Stop” button to return display to normal time.
ALARM MODE
In alarm mode, press “Start/Stop” button to enable or disable the Alarm (
Chime (
) function.
Chime Function
The Beep will sound every hour after activate the chime function.
43
) and
To set the Alarm:
1.
2.
3.
4.
5.
Press “Mode” button until alarm mode appears.
Press and hold “Set” button to begin setting alarm.
Press “Mode” button to select the alarm hour or minute for setting.
Press “Start/Stop” button to set the alarm hour or minute.
Press “Set” button to exit the alarm setting.
CHRONOGRAPH MODE
The chronograph counts up to 23 hours, 59 minutes, 59.99 seconds with 1/100
second and split time function.
1.
2.
3.
4.
Press “Mode” button until chronograph mode appears.
Press “Start/Stop” button to start the chronograph.
Press “Start/Stop” button to stop the chronograph.
Press “Set” button again to reset the chronograph.
Split time Measurement
Example of using split time measurement for two runners. Two runners can be timed
simultaneously; the first runner’s time can be recorded while the second runner’s
time will continue to be accumulated until he finishes.
4. Press “Start/Stop” button to stop the timing of the second runner and record the
time.
5. Press “Set” button to reset timing.
TIMER FUNCTION
1. Press “Start/Stop” button to start the timer.
2. Press “start/Stop” button to stop the timer.
3. Press “Set” Button to reset the timer.
To set the Timer:
1.
2.
3.
4.
5.
Press “Mode” button until timer mode appears.
Press and hold “Set” button to begin setting timer.
Press "Mode" button to select between hour or minute.
Press “Start/Stop” button to set the timer hour or minute.
Press “Set” button to exit the timer setting.
ELECTROLUMINESCENT BACKLIGHT
Press “Light” Button to activate the light function under each mode anytime.
1. Press “Start/Stop” button to start the timing of the first and second runner
2. Press “Set” button to stop and record the timing of the first runner.
("SPL" will blink on the display if the split time function is active. Even though the
stop watch is not on display, the timing will continue to run internally.)
3. Press “Set” button again to see the timing of the second runner. The stopwatch
will switch to display the internal accumulated time and continue timing of the
second runner.
44
45
CHRONOGRAPH MODE
digital Models
The sports watch count up to 19 hours 59 minutes 59.99 seconds with 1/100 second
and split time function.
adjust
light
crown
set
mode
MW32
1.
2.
3.
4.
Press ”Mode” button until chronograph mode appears.
Press “Adjust” button to start the chronograph.
Press “Adjust” button to stop the chronograph.
Press “Set” button again to reset the chronograph.
Split time Measurement
Example of using split time measurement for two runners. Two runners can be timed
simultaneously; the first runner’s time can be recorded while the second runner’s
time will continue to be accumulated until he finishes.
Press “Mode” button to cycle through “TIME”, ”CHRONOGRAPH”, “ALARM” and
“TIME SET” mode.
1. Press “Adjust” button to start the timing of the first and second runner
2. Press “Set” button to stop and record the timing of the first runner.
("Split" will blink on the display if the split time function is active. Even though the
stop watch is not on display, the timing will continue to run internally.)
3. Press “Set“ button again to catch up the timing of the second runner. The
stopwatch will jump to show the internal accumulated time and to carry on timing
of the second runner.
4. Press “Adjust” button to stop the timing of the second runner and record the time.
5. Press “Set” button to reset timing.
TIME MODE
ALARM MODE
This Digital watch has 6 functions
Time / Calendar / Day of week / Chronograph / Alarm / Electroluminescent backlight
MODE SELECTION
In time mode, the watch display the current time information on Hour, minute,
second, date, month and day of week. It is also display the “ON/OFF” status of Alarm
or Chime.
46
In alarm mode, press “Adjust” button to enable or disable the Alarm and Chime
function.
47
Alarm Function
1.
2.
3.
4.
Press ”Mode” button until Alarm mode appears.
Press “Set” button to select the alarm hour setting, the alarm will be set to ON.
Press “Adjust” button to set the alarm hour.
Press “Set” button to select the alarm minute setting and press “Adjust” button to
set the alarm minute.
5. Press “Set” button again to fix the alarm setting.
special function Models
Press “Mode” button until Time Set mode appears.
Press “Set” button to select the setting item in the order,
Second ➞ Hour ➞ Minute ➞ Month ➞ Date ➞ Day of Week
Press “Adjust” button to set the timing follow the order.
Press and hold the “adjust” button, the timing will cause repaid increment.
When setting the hour, the “H” indicate 24 hours mode, “A” or “P” indicate 12
hours mode.
6. Press “Mode” button to exit the time setting mode.
ELECTROLUMINESCENT BACKLIGHT
Press “Light” button to activate the light function under each mode anytime.
ABC
DatE
Tide cycle counter
PUSHER B
8272
Tide cycle hand
This Chronograph watch has 3 functions:
TIME, CALENDAR, TIDE
TIME
To set the time:
1. Pull crown to position “C”.
2. Turn crown clockwise / counter clockwise to correct time.
3. Push crown to position “A”.
CALENDAR
To set the calendar:
1. Pull crown to position “B”.
2. Turn crown clockwise to correct calendar.
3. Push crown to position “A”.
48
Crown Position
Hour Hand
The Beep will sound every hour after activate the chime function.
1.
2.
3.
4.
5.
PUSHER A
Tide amplitude and Moon
phase counter hand
Chime Function
TIME SET MODE
Small
second hand
Minute Hand
49
4th center hand
TIDE FUNCTION
To set the Tide Function - Central Hand
The tide cycle takes place over one revolution of the dial in 12 hours 25 minutes
and 14 seconds. High tide corresponds to the "12 o'clock" position and low tide
corresponds to the opposite position, hence "6 o'clock".
1. Press and hold pusher “B” to 3 seconds after the beep indicated for enter in
setting mode.
2. Press pusher “B” again to set the state of the local tide.
3. Continuous pressing pusher “B” to enable rapid setting to be performed.
Note: After 3 second without pressing pusher “B”, a beep indicated exit from setting
mode.
To set the Tide Amplitude (Moon Phase) – Counter at 10 o’clock small eye
The tide amplitude counter performs one revolution in 29 days 12 hours and 44 minutes.
1. Press and hold pusher “A” to 3 seconds after the beep indicated for enter in
setting mode.
2. Press pusher “A” again to set the tide amplitude corresponding to the moon
phase.
3. Continuous pressing pusher “A” to enable rapid setting to be performed.
Note:
– After 3 second without pressing pusher “A”, a beep indicated exit from setting
mode.
– The moon phase hand will start with its setting time, jumps step forward every 24
hours.
50
minute hand
24 cities
PUSHER A
Upper hand
date
ABC
world time scale
hour hand
Crown Position
chrono minutes scale
PUSHER C
PUSHER B
season scale
second hand
M366
lower hand
This watch has 4 functions:
TIME, CALENDAR, WORLDTIMES, SEASON
TIME
To set the time:
1. Pull crown to position ”C”
2. Turn crown clockwise / counter clockwise to correct the time.
3. Push crown back to position “A”.
CALENDAR
To set the CALENDAR:
1. Pull crown to position ”B”
2. Turn crown counter clockwise to correct the calendar.
3. Push crown back to position “A”.
51
WORLDTIME
To Set the World Time:
City Time Display Selection:
1. Pull crown to position “B”. The 4th center hand shows the world time zone city
and the upper hand shows the world time.
2. Press pusher “A” or “B” to move the 4th center hand to the city that represents
your home time zone.
3. Pull the crown to position “C”. The 4th centre hand will revert back to the 12:00
position. After five seconds, the upper hand moves and shows the world time (the
time of the city selected in previous step), the center hand shows the minutes of
the world time, and the lower hand shows the season.
IMPORTANT: After pulling out the crown to position "C", don't press any of the
pushers and turn the crown until all hands stop moving. (Approximately 10
seconds)
4. Press pusher “A” or “B” to move the 4th centre hand backward or forward to
adjust the world time, respectively, to set the world time zone to be the same as
the home time zone. Press and hold a pusher to change the time quickly. The
hands move together as the center hand makes one revolution, the upper hand
moves one hour.
5. Press pusher “C” to adjust the season if the displayed season is not correct for
the home time zone. If the home time zone observes daylight savings time, the
upper hand will move by one hour.
6. Push crown to position “A” after finish setting.
52
Press pusher “A” or “B” to move the 4th centre hand backward or forward for select
the city. The upper hand moves to show the time in the selected city.
Note: The world time scale is 24 hours.
4th CENTRE HAND ADJUSTMENT
1. Pull crown to position “C”. The upper and lower hand will reset to the end of their
sweeps automatically.
2. Press pusher “A” or “B” to adjust the 4th centre hand to “12” position.
3. Push back the crown to position “A”.
Note: If no pusher is pressed within five seconds of the hands stopping, the watch
will proceeds to the world time setting operation (see WORLDTIME setting).
SEASON SETTING
The season setting allows the watch to compensate for daylight savings time (also
called “summer time”).
The watch provides one setting to represent daylight savings time and standard time.
For the watch, the period of daylight savings time is SUMMER and the period of
standard time is WINTER. When the season in one city is set to SUMMER, all cities
in the same hemisphere are automatically set to SUMMER, while all cities in the
other hemisphere are automatically set to WINTER. The watch knows which cities
are in each hemisphere.
Press pusher “C” to adjust the season in the selected city.
53
LIMITED WARRANTY
The Basic Coverage: This NAUTICA watch (but not any battery, crystal, case, band
or strap) is warranted to the owner for a period of FIVE YEARS from the date of
purchase against defects In manufacture by Nautica Watches - not by the dealer
from whom the watch was purchased.
What Nautica Watches Will Do:
If this watch develops such a defect within the five year period it will be repaired (i.e., a
new or thoroughly reconditioned and inspected movement will be installed) or replaced
(a watch of equal value and similar appearance will be supplied) at our option, provided
it is returned with a $7.50 check or money order to cover costs of postage, handling
and service, and you provide proof of purchase and date of purchase.
This Limited Warranty Does Not Cover:
1) Nautica Watches will not repair defects related to servicing not performed by
Nautica Watches.
2) Nautica Watches will not provide any warranty service if your watch shows
evidence that it has been tampered with, misused, abused, or altered; for
example:
• moisture damage sufficient to affect the proper function of the watch;
• damage to the case; or
• visible cracking of the crystal.
3) Nautica Watches reserves the right to charge you for a replacement battery, if
the battery in your watch is depleted. No additional charge will be made unless
the five year warranty period has expired or servicing is necessary for reasons
beyond our control, in which case a moderate charge will be made.
4) NAUTICA WATCHES IS NOT LIABLE FOR INCIDENTAL, SPECIAL OR
CONSEQUENTIAL DAMAGES. Some states do not allow the exclusion or limitation
of incidental, special or consequential damages, so the above exclusion or limitation
may not apply to you.
Your Rights Under Implied Warranties and State Law: THIS LIMITED WARRANTY
IS IN LIEU OF ALL OTHER EXPRESSED WARRANTIES, OBLIGATIONS OR
LIABILITIES. NAUTICA WATCHES LIMITS THE DURATION OF ANY WARRANTY
IMPLIED BY STATE LAW, INCLUDING BUT NOT LIMITED TO THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, TO FIVE YEARS FROM THE DATE OF ORIGINAL PURCHASE. Some
states do not allow limitations on how long an implied warranty lasts, so the above
limitation may not apply to you. This warranty gives you specific legal rights, and you
may also have other rights which vary from state to state.
Care of Your Watch:
• Avoid exposing your watch to water, steam, or other forms of moisture, if your
watch is not water-resistant.
• If the crystal becomes damaged, have it replaced at once to avoid damage to the
movement.
• When your battery is depleted, have it replaced promptly. The particular type of
battery required is indicated on your caseback.
Service of Your Watch:
If your NAUTICA watch should ever need servicing, send it to:
TG SERVICE CENTER
PO BOX 2802, North Little Rock, AR 72115
Tel: 1-800-448-4639
Hours of Operation are 8:00 till 4:30 PM CST
Because of possible loss, we recommend insuring your watch, return receipt
requested, when using the mails. If you do not obtain a receipt within a reasonable
time, start a tracer through the originating post office. NEVER INCLUDE A SPECIAL
WATCHBAND OR ANY OTHER ARTICLE OF PERSONAL VALUE IN YOUR
SHIPMENT. PLEASE NOTE THAT WE MAY SUBSTITUTE A WATCH OF EQUAL
VALUE AND SIMILAR APPEARANCE FOR YOURS ON BOTH IN-WARRANTY AND
OUT-OF-WARRANTY REPAIRS.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement