Honda PCX150i Owners Manual
150i
http://mototh.com
10/02/17 16:49:56 32KWN600_002
IMPORTANT INFORMATION
OPERATOR AND PASSENGER
This scooter is designed to carry the operator and one passenger. Never exceed the
maximum weight capacity.
ON-ROAD USE
This scooter is designed to be used only on the road.
READ THIS OWNER’S MANUAL CAREFULLY
Pay special attention to the safety messages that appear throughout the manual. These
messages are fully explained in the ‘‘A Few Words About Safety’’ section which appears
before the Contents page.
This manual should be considered a permanent part of the scooter and should remain with
the scooter when resold.
http://mototh.com
10/02/17 16:49:59 32KWN600_003
Honda PCX
OWNER’S MANUAL
All information in this publication is based on the latest production information
available at the time of approval for printing. Honda Motor Co.,Ltd. reserves the
right to make changes at any time without notice and without incurring any
obligation.
No part of this publication may be reproduced without written permission.
http://mototh.com
10/02/17 16:50:04 32KWN600_004
WELCOME
The scooter presents you a challenge to master the machine, a challenge to adventure. You
ride through the wind, linked to the road by a vehicle that responds to your commands as no
other does. Unlike an automobile, there is no metal cage around you. Like an airplane, a preride inspection and regular maintenance are essential to your safety. Your reward is freedom.
To meet the challenges safely, and to enjoy the adventure fully, you should become
thoroughly familiar with this owner’s manual BEFORE YOU RIDE THE SCOOTER.
As you read this manual, you will find information that is preceded by a
symbol. This
information is intended to help you avoid damage to your scooter, other property, or the
environment.
When service is required, remember that your Honda dealer knows your scooter best. If you
have the required mechanical ‘‘know-how’’ and tools, your dealer can supply you with an
Official Honda Shop Manual to help you perform many maintenance and repair tasks.
Pleasant riding, and thank you for choosing a Honda !
http://mototh.com
10/02/17 16:50:11 32KWN600_005
The following code in this manual indicates the country.
The illustrations herein are based on the ED type.
E
F
ED
U
KO
UK
France
European direct sales
Australia
New Zealand
Korea
The specifications may vary with each locale.
http://mototh.com
10/02/17 16:50:15 32KWN600_006
A FEW WORDS ABOUT SAFETY
Your safety, and the safety of others, is very important. And operating this scooter safely is
an important responsibility.
To help you make informed decisions about safety, we have provided operating procedures
and other information on labels and in this manual. This information alerts you to potential
hazards that could hurt you or others.
Of course, it is not practical or possible to warn you about all hazards associated with
operating or maintaining a scooter. You must use your own good judgment.
You will find important safety information in a variety of forms, including:
Safety Labels –– on the scooter.
Safety Messages –– preceded by a safety alert symbol
DANGER, WARNING, or CAUTION.
These signal words mean:
http://mototh.com
and one of three signal words:
10/02/17 16:50:19 32KWN600_007
You WILL be KILLED or SERIOUSLY HURT if you don’t follow
instructions.
You CAN be KILLED or SERIOUSLY HURT if you don’t follow
instructions.
You CAN be HURT if you don’t follow instructions.
Safety Headings –– such as Important Safety Reminders or Important Safety Precautions.
Safety Section –– such as Scooter Safety.
Instructions –– how to use this scooter correctly and safely.
This entire manual is filled with important safety information –– please read it carefully.
http://mototh.com
10/02/17 16:50:31 32KWN600_008
OPERATION
page
1 SCOOTER SAFETY
1 IMPORTANT SAFETY
INFORMATION
2 PROTECTIVE APPAREL
5 LOAD LIMITS AND GUIDELINES
10 IMAGE LABELS
page
45 ESSENTIAL INDIVIDUAL
COMPONENTS
45
IGNITION SWITCH
46
FUEL LID AND SEAT OPENER
SWITCH
48
RIGHT HANDLEBAR CONTROLS
49
LEFT HANDLEBAR CONTROLS
15 PARTS LOCATION
18 INSTRUMENTS AND
INDICATORS
27 MAJOR COMPONENTS
(Information you need to operate
this scooter)
27 BRAKES
33 COOLANT
35 FUEL
38 ENGINE OIL
39 TUBELESS TYRES
http://mototh.com
10/02/17 16:50:42 32KWN600_009
page
50 FEATURES
(Not required for operation)
50 STEERING LOCK
51 SHUTTER
52 IDLING STOP SYSTEM
61 HELMET HOLDER
62 CENTER COMPARTMENT
63 DOCUMENT COMPARTMENT
64 GLOVE BOX
65 HEADLIGHT AIM VERTICAL
ADJUSTMENT
66 CLIP
page
67 OPERATION
67
PRE-RIDE INSPECTION
68
STARTING THE ENGINE
73
RUNNING-IN
74
RIDING
83
PARKING
84
ANTI-THEFT TIPS
http://mototh.com
10/02/17 16:50:59 32KWN600_010
MAINTENANCE
page
85 MAINTENANCE
85 THE IMPORTANCE OF
MAINTENANCE
86 MAINTENANCE SAFETY
87 SAFETY PRECAUTIONS
88 MAINTENANCE SCHEDULE
91 TOOL KIT
92 SERIAL NUMBERS
94 COLOUR LABEL
95 AIR CLEANER
96 CRANKCASE BREATHER
97 ENGINE OIL
101 ENGINE OIL STRAINER SCREEN
103 SPARK PLUG
106 COOLANT
107 THROTTLE OPERATION
107 FRONT AND REAR SUSPENSION
INSPECTION
108 SIDE STAND
109 BRAKE PAD WEAR
page
110
111
114
116
BRAKE SHOE WEAR
BATTERY
FUSE REPLACEMENT
BULB REPLACEMENT
124 CLEANING
128 STORAGE GUIDE
STORAGE
128
REMOVAL FROM STORAGE
130
131 TAKING CARE OF THE
UNEXPECTED
132 SPECIFICATIONS
136 CATALYTIC CONVERTER
http://mototh.com
10/02/17 16:51:06 32KWN600_011
SCOOTER SAFETY
IMPORTANT SAFETY INFORMATION
Your scooter can provide many years of
service and pleasure − if you take
responsibility for your own safety and
understand the challenges that you can
meet on the road.
There is much that you can do to protect
yourself when you ride. You’ll find many
helpful recommendations throughout this
manual. Following are a few that we
consider to be most important.
Always Wear a Helmet
It’s a proven fact: helmets significantly
reduce the number and severity of head
injuries. So always wear an approved
motorcycle helmet and make sure your
passenger does the same. We also
recommend that you wear eye protection,
sturdy boots, gloves, and other protective
gear (page 2 ).
Make Yourself Easy to See
Some drivers do not see scooters because
they are not looking for them. To make
yourself more visible, wear bright reflective
clothing, position yourself so other drivers
can see you, signal before turning or
changing lanes, and use your horn when it
will help others notice you.
Ride Within Your Limits
Pushing the limits is another major cause of
scooter crashes. Never ride beyond your
personal abilities or faster than conditions
warrant. Remember that alcohol, drugs,
fatigue and inattention can significantly
reduce your abilit y to make good
judgements and ride safely.
1
http://mototh.com
10/02/17 16:51:12 32KWN600_012
Don’t Drink and Ride
Alcohol and riding don’t mix. Even one
drink can reduce your ability to respond to
changing conditions, and your reaction time
gets worse with every additional drink. So
don’t drink and ride, and don’t let your
friends drink and ride either.
Keep Your Bike in Safe Condition
For safe riding, it’s important to inspect
your scooter before every ride and perform
all recommended maintenance. Never
exceed load limits, and only use accessories
that have been approved by Honda for this
scooter. See page 5 for more details.
PROTECTIVE APPAREL
For your safety, we strongly recommend
that you always wear an approved
motorcycle helmet, eye protection, boots,
gloves, trousers, and a long-sleeved shirt or
jacket whenever you ride. Although
complete protection is not possible, wearing
proper gear can reduce the chance of injury
when you ride.
Following are suggestions to help you
choose proper gear.
Not wearing a helmet increases the
chance of serious injury or death in a
crash.
Be sure you and your passenger
always wear a helmet, eye protection
and other protective apparel when you
ride.
2
http://mototh.com
10/02/17 16:51:16 32KWN600_013
Helmets and Eye Protection
Your helmet is your most important piece of
riding gear because it offers the best
protection against head injuries. A helmet
should fit your head comfortably and
securely. A bright-coloured helmet can
make you more noticeable in traffic, as can
reflective strips.
An open-face helmet offers some protection,
but a full-face helmet offers more. Always
wear a face shield or goggles to protect
your eyes and help your vision.
Additional Riding Gear
In addition to a helmet and eye protection,
we also recommend:
Sturdy boots with non-slip soles to help
protect your feet and ankles.
Leather gloves to keep your hands warm
and help prevent blisters, cuts, burns and
bruises.
A motorcycle riding suit or jacket for
comfort as well as protection. Brightcoloured and reflective clothing can help
make you more noticeable in traffic. Be
sure to avoid loose clothes that could get
caught on any part of your scooter.
3
http://mototh.com
10/02/17 16:51:21 32KWN600_014
ALWAYS wear a helmet.
You should also wear a face shield or goggles.
Wear bright or reflective clothing.
Clothes should be close-fitting.
Wear gloves.
Shoes should be close-fitting, have low heels and offer ankle protection.
4
http://mototh.com
10/02/17 16:51:26 32KWN600_015
LOAD LIMITS AND GUIDELINES
Your scooter has been designed to carry
you, one passenger and a limited amount of
cargo. When you add cargo or carry a
passenger, you may feel some difference
during acceleration and braking. But so long
as you keep your scooter well-maintained,
with good tyres and brakes, you can safely
carry loads within the given limits and
guidelines.
Loading
How much weight you put on your scooter,
and how you load it, are important to your
safety. Anytime you ride with a passenger
or cargo you should be aware of the
following information.
However, exceeding the weight limit or
carrying an unbalanced load can seriously
affect your scooter’s handling, braking and
stability. Non-Honda accessories, improper
modifications, and poor maintenance can
also reduce your safety margin.
Overloading or improper loading can
cause a crash and you can be
seriously hurt or killed.
Follow all load limits and other loading
guidelines in this manual.
The following pages give more specific
information on loading, accessories and
modifications.
5
http://mototh.com
10/02/17 16:51:36 32KWN600_016
Load Limits
Following are the load limits for your scooter:
Maximum weight capacity:
180 kg (397 lb) … Except KO type
152 kg (335 lb) … KO type only
Includes the weight of the rider, passenger, all cargo and all accessories
Maximum cargo weight:
13 kg (29 lb) … Except KO type
11 kg (24 lb) … KO type only
The weight of added accessories will reduce the maximum cargo weight you can carry.
Putting too much weight in individual storage compartments can also affect stability and
handling. So be sure to stay within the limits given below:
Maximum weight:
in center compartment
in glove box
10 kg (22 lb)
1.0 kg (2.2 lb)
Glove box:
weight limit:
1.0 kg (2.2 lb)
Center compartment:
weight limit:
10 kg (22 lb)
6
http://mototh.com
10/02/17 16:51:42 32KWN600_017
Loading Guidelines
Your scooter is primarily intended for
transporting you and a passenger. You may
wish to secure a jacket or other small items
to the seat when you are not riding with a
passenger.
If you wish to carry more cargo, check with
your Honda dealer for advice, and be sure
to read the inf ormat ion regarding
accessories on page 8 .
Improperly loading your scooter can affect
its stability and handling. Even if your
scooter is properly loaded, you should ride
at reduced speeds whenever carrying cargo.
Follow these guidelines whenever you carry
a passenger or cargo:
Check that both tyres are properly
inflated (page 39 ).
To prevent loose items from creating a
hazard, make sure the center
compartment, glove box is closed and
that any other cargo is securely tied down
before you ride away.
Place cargo weight as close to the center
of the scooter as possible.
Balance cargo weight evenly on both
sides.
7
http://mototh.com
10/02/17 16:51:48 32KWN600_018
Accessories and Modifications
Modifying your scooter or using non-Honda
accessories can make your scooter unsafe.
Bef ore you consider making any
modifications or adding an accessory, be
sure to read the following information.
Accessories
We strongly recommend that you use only
Honda Genuine Accessories that have been
specifically designed and tested for your
scooter. Because Honda cannot test all
other accessories, you must be personally
responsible for proper selection, installation
and use of non-Honda accessories. Check
with your dealer for assistance and always
follow these guidelines:
Improper accessories or modifications
can cause a crash in which you can be
seriously hurt or killed.
Follow all instructions in this owner’s
manual regarding accessories and
modifications.
Make sure the accessory does not
obscure any lights, reduce ground
clearance and banking angle, limit
suspension travel or steering travel, alter
your riding position or interfere with
operating any controls.
Be sure electrical equipment does not
exceed the scooter’s electrical system
capacity (page 135 ). A blown fuse can
cause a loss of lights or engine power.
8
http://mototh.com
10/02/17 16:51:52 32KWN600_019
Do not pull a trailer or sidecar with your
scooter. This scooter was not designed
for these attachments, and their use can
seriously impair your scooter’s handling.
Modifications
We strongly advise you not to remove any
original equipment or modify your scooter
in any way that would change its design or
operation. Such changes could seriously
impair your scooter’s handling, stability and
braking, making it unsafe to ride.
Removing or modif ying your lights,
mufflers, emission control system or other
equipment can also make your scooter
illegal.
9
http://mototh.com
10/02/17 16:51:56 32KWN600_020
IMAGE LABELS
〈Except KO type〉
The following pages describe the label
meanings. Some labels warn you of
potential hazards that could cause serious
injury. Others provide important safety
information. Read this information carefully
and don’t remove the labels.
There is a specific symbol on each label.
The meanings of each symbol and label are
as follows.
If a label comes off or becomes hard to read,
co nt a c t y ou r H on da de a l e r f o r a
replacement.
10
http://mototh.com
10/02/17 16:52:02 32KWN600_021
Read instructions contained in Owner’s Manual carefully.
Read instructions contained in Shop Manual carefully.
In the interest of safety, take the motorcycle to be serviced only by a
Honda dealer.
DANGER (with RED background)
You WILL be KILLED or SERIOUSLY HURT if you don’t follow
instructions.
WARNING (with ORANGE background)
You CAN be KILLED or SERIOUSLY HURT if you don’t follow
instructions.
CAUTION (with YELLOW background)
You CAN be HURT if you don’t follow instructions.
11
http://mototh.com
10/02/17 16:52:09 32KWN600_022
RADIATOR CAP LABEL
DANGER
NEVER OPEN WHEN HOT.
Hot coolant will scald you.
Relief pressure valve begins to open at 1.1 kgf/cm2.
ACCESSORIES AND LOADING WARNING LABEL
WARNING
ACCESSORIES AND LOADING
The safety stability and handling of this motorcycle
may be affected by the addition of accessories and
luggage.
Read carefully the instructions contained in user’s
manual and installation guide before installing any
accessory.
The total weight of accessories and luggage added to
rider’s and passenger’s weight should not exceed
180 kg (397 lb) , which is the maximum weight
capacity.
The luggage weight must not exceed
13 kg (29 lb) under any circumstances.
The fitting of large fork-mounted or large handlebarmounted fairing is not recommended.
12
http://mototh.com
10/02/17 16:52:16 32KWN600_023
TYRE INFORMATION LABEL
Cold tyre pressure:
[Driver only]
Front
200 kPa (2.00 kgf/cm
Rear
225 kPa (2.25 kgf/cm
[Driver and passenger]
200 kPa (2.00 kgf/cm
Front
Rear
250 kPa (2.50 kgf/cm
Tyre size:
90/90-14M/C 46P
Front
100/90-14M/C 57P
Rear
Tyre brand: IRC
SS-560F
Front
SS-560R
Rear
, 29 psi)
, 33 psi)
, 29 psi)
, 36 psi)
13
http://mototh.com
10/02/17 16:52:26 32KWN600_024
SAFETY REMINDER LABEL
For your protection, always wear helmet and protective
gear.
FUEL LABEL〈E, F, ED type only〉
UNLEADED PETROL ONLY
CARGO LIMIT LABEL
Do not exceed 10 kg (22 lb)
.
CARGO LIMIT LABEL
Do not exceed 1.0 kg (2.2 lb) .
14
http://mototh.com
10/02/17 16:52:31 32KWN600_025
PARTS LOCATION
CBS brake fluid reservoir
Instruments and indicators
Front brake fluid reservoir
Rearview mirror
Rearview mirror
Rear brake lever
Front brake lever
Headlight dimmer
switch
Throttle grip
Idling Stop switch
Horn button
Start button
Turn signal switch
Glove box
Ignition switch
Shutter
Fuel lid and
seat opener switch
15
http://mototh.com
10/02/17 16:52:34 32KWN600_026
Battery
Fuse box
Document compartment
Tool kit
Oil fill cap/dipstick
Passenger footpeg
16
http://mototh.com
10/02/17 16:52:37 32KWN600_027
Center compartment
Helmet holder
Coolant reserve tank
Air cleaner
Passenger footpeg
Fuel fill cap
Spark plug
Side stand
Center stand
17
http://mototh.com
10/02/17 16:52:41 32KWN600_028
INSTRUMENTS AND
INDICATORS
The indicators are contained in the
instrument panel. Their functions are
described in the tables on the following
pages.
(1) Mode switch
(2) High coolant temperature indicator
(3) Left turn signal indicator
(4) Speedometer
(5) Right turn signal indicator
(6) Odometer/Tripmeter/Fuel gauge
display
(7) PGM-FI malfunction indicator lamp
(MIL)
(8) High beam indicator
(9) STAND BY indicator
(3)
(2)
(4)
(5)
(6)
(1)
(9)
18
http://mototh.com
(8)
(7)
10/02/17 16:52:47 32KWN600_029
(Ref.No.) Description
(1) Mode switch
Function
Resets the tripmeter or selects the operation
mode: tripmeter or odometer (page 24 ).
(2) High coolant temperature
indicator (red)
Lights when the coolant is over the specified
temperature. If the indicator goes on while riding,
stop the engine and check the reserve tank coolant
level. Read pages 33 − 34 and do not ride the
scooter until the problem has been corrected.
Exceeding maximum running temperature may
cause serious engine damage.
19
http://mototh.com
10/02/17 16:52:53 32KWN600_030
(Ref.No.) Description
(3) Left turn signal indicator
(green)
Function
Flashes when the left turn signal operates.
(4) Speedometer
Shows riding speed.
T his shows your speed in kilometers per hour
(km/h) and/or miles per hour (mph) depending on
the type.
The speedometer needle will swing to the maximum
scale on the dial once when the ignition switch is
turned ON.
20
http://mototh.com
10/02/17 16:53:03 32KWN600_031
(Ref.No.) Description
(5) Right turn signal indicator
(green)
Function
Flashes when the right turn signal operates.
(6) Odometer/Tripmeter/
Fuel gauge display
The display includes the following functions;
This display shows the initial display (page 23 ).
Odometer
Shows accumulated mileage (page 24 ).
Tripmeter
Shows mileage per trip (page 24 ).
Fuel gauge
Shows approximate fuel supply available (page
26 ).
(7) PGM-FI malfunction
indicator lamp (MIL)
(amber)
Lights when there is any abnormality in the
PGM-FI (Programmed Fuel Injection) system.
Should also light for a few seconds and then go off
when the ignition switch is turned ON.
If it comes on at any other time, reduce speed and
take the scooter to your Honda dealer as soon as
possible.
21
http://mototh.com
10/02/17 16:53:08 32KWN600_032
(Ref.No.) Description
(8) High beam indicator (blue)
Function
Lights when the headlight is on high beam.
(9) STAND BY indicator
(amber)
Flashes when the Idling Stop system is activated
(page 52 ). If you get off the scooter (without sitting)
while the engine is stopping by the Idling Stop
system, the STAND BY indicator will go out, and for
about 3 minutes later, the Idling Stop system will be
cancelled.
22
http://mototh.com
10/02/17 16:53:11 32KWN600_033
Initial Display
When the ignition switch is turned ON, the
display will temporarily show all the modes
and digital segments so you can make sure
the liquid crystal display is functioning
properly.
23
http://mototh.com
10/02/17 16:53:18 32KWN600_034
Odomet er/T ripmet er/F uel Gaug e
Display
The display ( 1 ) has three functions,
odometer, tripmeter and fuel gauge.
Odometer
Except E type: Odometer and tripmeter
read in kilometers.
E type: Odometer and tripmeter read in
miles.
(1)
Tripmeter
Push the mode switch ( 2 ) to select the
‘‘ODO’’ or ‘‘TRIP’’ mode.
(1) Odometer/Tripmeter/Fuel gauge display
(2)
(2) Mode switch
24
http://mototh.com
10/02/17 16:53:21 32KWN600_035
To reset the tripmeter, push and hold the
mode switch for more than 2 seconds, with
the display in the ‘‘TRIP’’ mode.
Tripmeter
reset
(2)
(2) Mode switch
25
http://mototh.com
10/02/17 16:53:27 32KWN600_036
(1)
Fuel Gauge
The fuel gauge liquid crystal display ( 1 )
shows the approximate available fuel in a
graduated display. When all segments up to
F ( 2 ) are on, the fuel tank is full.
The fuel tank capacity is:
6.1 (1.61 US gal , 1.34 Imp gal)
When there is only one segment ( 3 ) left,
fuel will be low and you should refuel as
soon as possible.
The amount of fuel left in the tank with the
vehicle set upright is approximately:
1.5 (0.40 US gal , 0.33 Imp gal)
This segment flashes when the fuel
decreases further.
(3)
(1) Fuel gauge
(2) Segment F
(3) Segment E
26
http://mototh.com
(2)
10/02/17 16:53:31 32KWN600_037
MAJOR COMPONENTS
(Information you need to operate this scooter)
BRAKES
Combined Brake System (CBS)
This scooter is equipped with a Combined
Brake System. Operating the rear brake
lever applies the rear brake and a portion of
t he f ront br ake . F or f ull braking
effectiveness, use both the front and rear
brake lever simultaneously, as you would
with a conventional scooter braking system.
As with a conventional scooter braking
system, excessively hard application of the
brake controls may cause wheel lock,
reducing control of the scooter.
For normal braking, apply both the front
and rear brake lever to match your road
speed. For maximum braking, close the
throttle and firmly apply the front and rear
brake lever.
27
http://mototh.com
10/02/17 16:53:37 32KWN600_038
Front Brake
This scooter has a hydraulic front disc
brake.
As the brake pads wear, brake fluid level
drops.
There are no adjustments to perform, but
fluid level and pad wear must be inspected
periodically. The system must be inspected
frequently to ensure there are no fluid leaks.
If the control lever free travel becomes
excessive and the brake pads are not worn
beyond the recommended limit (page 109 ),
there is probably air in the brake system
and it must be bled. See your Honda dealer
for this service.
Front Brake Fluid Level:
With the scooter in an upright position,
check the fluid level. It should be above the
LOWER level mark ( 1 ). If the level is at or
below the LOWER level mark, check the
brake pads for wear (page 109 ).
Worn pads should be replaced. If the pads
are not worn, have your brake system
inspected for leaks.
The recommended brake fluid is Honda
DOT 3 or DOT 4 brake fluid from a sealed
container, or an equivalent.
Other Checks:
Make sure there are no fluid leaks. Check
for deterioration or cracks in the hoses and
fittings.
(1)
(1) LOWER level mark
28
http://mototh.com
10/02/17 16:53:43 32KWN600_039
CBS Brake Fluid Level:
With the scooter in an upright position,
check the fluid level. It should be between
the UPPER ( 1 ) and LOWER ( 2 ) level
marks. If the level is at or below the
LOWER level mark, check the brake pads
for wear (page109 ).
(1)
Worn pads should be replaced. If the pads
are not worn, have your brake system
inspected for leaks.
(2)
The recommended brake fluid is Honda
DOT 3 or DOT 4 brake fluid from a sealed
container, or an equivalent.
Other Checks:
Make sure there are no fluid leaks. Check
for deterioration or cracks in the hoses and
fittings.
(1) UPPER level mark
(2) LOWER level mark
29
http://mototh.com
10/02/17 16:53:48 32KWN600_040
Rear Brake
Adjust the freeplay of the brake lever with
the front wheel pointed straight ahead.
(1)
Adjustment:
1. Place the scooter on its center stand.
2. Measure the distance the rear brake
lever ( 1 ) moves before the brake starts
to take hold.
Freeplay at the tip of the brake lever should
be:
10−20 mm (0.4−0.8 in)
(1) Rear brake lever
30
http://mototh.com
10/02/17 16:53:54 32KWN600_041
3. If adjustment is necessary, turn the rear
brake adjusting nut ( 2 ).
(2)
Adjust by turning the rear brake adjusting
nut a half-turn at a time. Make sure the cutout on the adjusting nut is seated on the
brake arm pin ( 3 ) after making final
freeplay adjustment.
4. Apply the brake several times and check
for free wheel rotation after the brake
lever is released.
If proper adjustment cannot be obtained by
this method, see your Honda dealer.
(B)
(A )
(3)
(2) Rear brake adjusting
nut
(3) Brake arm pin
(A) Decrease freeplay
(B) Increase freeplay
31
http://mototh.com
10/02/17 16:54:01 32KWN600_042
After adjustment, push the brake arm ( 4 )
to confirm that there is a gap between the
rear brake adjusting nut ( 2 ) and the brake
arm pin ( 3 ).
(2)
(3)
cut-out
correctly
seated
cut-out
not seated
(4)
(3)
(2)
(3)
(2)
(2) Rear brake adjusting nut
(3) Brake arm pin
(4) Brake arm
Other Checks:
Check the brake cable for kinks or signs of
wear that could cause sticking or failure.
L ubricat e t he bra ke cable wit h a
commercially available cable lubricant to
prevent premature wear and corrosion.
Make sure the brake arm, spring and
fasteners are in good condition.
After adjustment, confirm the freeplay of
the brake lever.
32
http://mototh.com
10/02/17 16:54:06 32KWN600_043
COOLANT
Coolant Recommendation
The owner must properly maintain the
coolant to prevent freezing, overheating,
and corrosion. Use only high quality
ethylene glycol antif reeze containing
corrosion protection inhibitors specifically
recommended for use in aluminum engines.
(SEE ANTIFREEZE CONTAINER LABEL).
Use only low-mineral drinking water or
distilled water as a part of the antifreeze
solution. Water that is high in mineral
content or salt may be harmful to the
aluminum engine.
The factory provides a 50/50 solution of
antifreeze and distilled water in this scooter.
This coolant solution is recommended for
most operating temperatures and provides
good corrosion protection. A higher
concentration of antifreeze decreases the
cooling system perf ormance and is
recommended only when additional
protection against freezing is needed. A
concentration of less than 40/60 (40%
antifreeze) will not provide proper corrosion
protection. During freezing temperatures,
check the cooling system frequently and
add higher concentrations of antifreeze (up
to a maximum of 60% antifreeze) if required.
Using coolant with silicate inhibitors may
cause premature wear of water pump seals
or blockage of radiator passages.
Using tap water may cause engine damage.
33
http://mototh.com
10/02/17 16:54:12 32KWN600_044
Inspection
The reserve tank ( 1 ) is in the center
compartment.
Open the seat (page 47 ) and check the
coolant level in the reserve tank while the
engine is at the normal operating
temperature with the scooter in an upright
position. If the coolant level is below the
LOWER level mark ( 2 ), remove the clip
( 3 ) (page 66 ) and coolant reserve tank lid
( 4 ). Open the reserve tank cap ( 5 ) and add
coolant mixture until it reaches the UPPER
level mark ( 6 ).
(3)
(4)
(1)
Always add coolant to the reserve tank. Do
not attempt to add coolant by removing the
radiator cap.
(2)
(6)
If the reserve tank is empty, or if coolant
loss is excessive, check for leaks and see
your Honda dealer for repair.
(1) Reserve tank
(2) LOWER level mark
(3) Clip
34
http://mototh.com
(5)
(4) Reserve tank lid
(5) Reserve tank cap
(6) UPPER level mark
10/02/17 16:54:20 32KWN600_045
FUEL
Fuel Tank
The fuel tank is located behind the fuel lid.
Fuel tank capacity is:
(1)
6.1 (1.61 US gal , 1.34 Imp gal)
Open the fuel lid ( 1 ) (page 46 ). Remove
the fuel fill cap ( 2 ) by turning it
counterclockwise.
Do not overfill the tank. There should be
no fuel in the level plate ( 3 ).
After refueling, be sure to tighten the fuel
fill cap firmly by turning it clockwise.
Make sure that the arrow marks ( 4 ) on the
fuel fill cap and fuel tank is aligned.
Close the fuel lid.
(3)
(2)
(4)
Petrol is highly flammable and
explosive. You can be burned or
seriously injured when handling fuel.
Stop the engine and keep heat,
sparks, and flame away.
Refuel only outdoors.
Wipe up spills immediately.
(1) Fuel lid
(2) Fuel fill cap
(3) Level plate
(4) Arrow marks
35
http://mototh.com
10/02/17 16:54:23 32KWN600_046
Use unleaded petrol with a research octane
number of 91 or higher.
The use of leaded petrol will cause
premature damage to the catalytic
converter.
If ‘‘spark knock’’ or ‘‘pinking’’ occurs at a
steady engine speed under normal load,
change brands of petrol. If spark knock or
pinking persists, consult your Honda dealer.
Failure to do so is considered misuse, and
damage caused by misuse is not covered by
Honda’s Limited Warranty.
36
http://mototh.com
10/02/17 16:54:26 32KWN600_047
Petrol Containing Alcohol
If you decide to use a petrol containing
alcohol (gasohol), be sure it’s octane rating
is at least as high as that recommended by
Honda. There are two types of ‘‘gasohol’’:
one containing ethanol, and the other
containing methanol. Do not use petrol that
contains more than 10 % ethanol. Do not use
petrol containing methanol (methyl or wood
alcohol) that does not also contain
cosolvents and corrosion inhibitors for
methanol. Never use petrol containing more
than 5 % methanol, even if it has cosolvents
and corrosion inhibitors.
The use of petrol containing more than 10 %
ethanol (or more than 5 % methanol) may:
Damage the painting of the fuel tank.
Damage the rubber tubes of the fuel line.
Cause corrosion of the fuel tank.
Cause poor drivability.
Before buying fuel from an unfamiliar
station, try to find out if the fuel contains
alcohol. If it does, confirm the type and
percentage of alcohol used. If you notice
any undesirable operating symptoms while
using a petrol that contains alcohol, or one
that you think contains alcohol, switch to a
petrol that you know does not contain
alcohol.
37
http://mototh.com
10/02/17 16:54:34 32KWN600_048
ENGINE OIL
Engine Oil Level Check
Check the engine oil level each day before
riding the scooter.
The level must be maintained between the
upper ( 1 ) and lower ( 2 ) level marks on the
oil fill cap/dipstick ( 3 ).
1. Start the engine and let it idle for 3−5
minutes.
2. Stop the engine and put the scooter on its
center stand on level ground.
3. After 2 − 3 minutes, remove the oil fill
cap/dipstick, wipe it clean, and reinsert
the oil fill cap/dipstick without screwing
it in. Remove the oil fill cap/dipstick. The
oil level should be between the upper and
lower level marks on the oil fill cap/
dipstick.
4. If required, add the specified oil (see
page 97 ) up to the upper level mark. Do
not overfill.
5. Reinstall the oil fill cap/dipstick. Check
for oil leaks.
Running the engine with insufficient oil
pressure may cause serious engine damage.
(3)
(1)
(2)
(1) Upper level mark
(2) Lower level mark
(3) Oil fill cap/dipstick
38
http://mototh.com
10/02/17 16:54:39 32KWN600_049
TUBELESS TYRES
To safely operate your scooter, your tyres
must be the proper type and size, in good
condition with adequate tread, and correctly
inflated for the load you are carrying. The
following pages give more detailed information on how and when to check your air
pressure, how to inspect your tyres for
damage, and what to do when your tyres
need to be repaired or replaced.
Air Pressure
Keeping your tyres properly inflated
provides the best combination of handling,
tread life and riding comfort. Generally,
underinf lated tyres w ear unevenly,
adversely affect handling, and are more
likely to fail from being overheated.
Overinflated tyres make your scooter ride
harshly, are more prone to damage from
road hazards, and wear unevenly.
Using tyres that are excessively worn
or improperly inflated can cause a
crash in which you can be seriously
hurt or killed.
We recommend that you visually check
your tyres before every ride and use a
gauge to measure air pressure at least once
a month or any time you think the tyres
might be low.
Tubeless tyres have some self-sealing
ability if they are punctured. However,
because leakage is often very slow, you
should look closely for punctures whenever
a tyre is not fully inflated.
Follow all instructions in this owner’s
manual regarding tyre inflation and
maintenance.
39
http://mototh.com
10/02/17 16:54:46 32KWN600_050
Always check air pressure when your tyres
are ‘‘cold’’ − when the scooter has been
parked for at least three hours. If you check
air pressure when your tyres are ‘‘warm’’ −
when the scooter has been ridden for even
a few miles − the readings will be higher
than if the tyres were ‘‘cold’’. This is normal,
so do not let air out of the tyres to match
the recommended cold air pressures given
below. If you do, the tyres will be
underinflated.
The recommended ‘‘cold’’ tyre pressures
are:
kPa (kgf/cm2, psi)
Driver
only
Front
Rear
200 (2.00 , 29)
225 (2.25 , 33)
Driver and
one passenger
Front
Rear
200 (2.00 , 29)
250 (2.50 , 36)
Inspection
Whenever you check the tyre pressures,
you should also examine the tyre treads and
sidewalls for wear, damage, and foreign
objects:
Look for:
Bumps or bulges in the side of the tyre or
the tread. Replace the tyre if you find any
bumps or bulges.
Cuts, splits or cracks in the tyre. Replace
the tyre if you can see fabric or cord.
Excessive tread wear.
Also, if you hit a pothole or hard object, pull
to the side of the road as soon as you can
safely and carefully inspect the tyres for
damage.
40
http://mototh.com
10/02/17 16:54:49 32KWN600_051
Tread Wear
Replace tyres immediately when the wear
indicator ( 1 ) appears at on the tyre.
(2)
(1)
(1) Wear indicator
(2) Wear indicator location mark
41
http://mototh.com
10/02/17 16:54:53 32KWN600_052
Tyre Repair
If a tyre is punctured or damaged, you
should replace it, not repair it. As discussed
below, a tyre that is repaired, either
temporarily or permanently, will have lower
speed and performance limits than a new
tyre.
A temporary repair, such as an external
tubeless tyre plug, may not be safe for
normal speeds and riding conditions. If a
temporary or emergency repair is made to a
tyre, you should ride slowly and cautiously
to a dealer and have the tyre replaced. If
possible, you should not carry a passenger
or cargo until a new tyre is installed.
Even if a tyre is professionally repaired with
a permanent internal patch plug, it will not
be as good as a new tyre. You should not
exceed 80 km/h (50 mph) for the first 24
hours, or 130 km/h (80 mph) at any time
thereafter. In addition, you may not be able
to safely carry as much weight as with a
new t yre. T her ef ore, w e strongly
recommend that you replace a damaged
tyre. If you choose to have a tyre repaired,
be sure the wheel is balanced before you
ride.
42
http://mototh.com
10/02/17 16:54:59 32KWN600_053
Tyre Replacement
The tyres that came on your scooter were
designed to match the perf ormance
capabilities of your scooter and provide the
best combination of handling, braking,
durability and comfort.
The recommended tyres for your scooter
are:
Front: 90/90-14M/C 46P
IRC
SS-560F
Rear: 100/90-14M/C 57P
IRC
SS-560R
Installing improper tyres on your
scooter can affect handling and
stability. This can cause a crash in
which you can be seriously hurt or
killed.
Type: bias-ply, tubeless
Whenever you replace a tyre, use one that
is equivalent to the original and be sure the
wheel is balanced after the new tyre is
installed.
Always use the size and type of tyres
recommended in this owner’s manual.
43
http://mototh.com
10/02/17 16:55:03 32KWN600_054
Important Safety Reminders
Do not install a tube inside a tubeless tyre
on this scooter. Excessive heat build-up
can cause the tube to burst.
Use only tubeless tyres on this scooter.
The rims are designed for tubeless tyres,
and during hard acceleration or braking,
a tube-type tyre could slip on the rim and
cause the tyre to rapidly deflate.
44
http://mototh.com
10/02/17 16:55:09 32KWN600_055
ESSENTIAL INDIVIDUAL COMPONENTS
IGNITION SWITCH
The ignition switch ( 1 ) is on the right
side below the steering stem.
OFF
(1)
SEAT
FUEL
ON
LOCK
Key Position
LOCK
(Steering lock)
OFF
Function
Steering is locked. Engine and lights cannot be
operated.
Engine and lights cannot be operated.
SEAT
FUEL
ON
Fuel lid and seat opener switch can be operated.
Engine and lights cannot be operated.
Engine can be operated.
The brakelight, meter light, turn signals and
horn can be operated.
The headlight operates only when the engine is
running.
(1) Ignition switch
Key Removal
Key can be
removed
Key can be
removed
Key cannot be
removed
Key cannot be
removed
45
http://mototh.com
10/02/17 16:55:18 32KWN600_056
F UEL L ID A ND SEA T OPENER
SWITCH
If the ignition switch is ON or OFF position,
fuel lid and seat opener switch ( 1 ) will not
operate.
(3)
(2)
(5)
(1)
(4)
Fuel Lid
Open the Fuel Lid:
1. Insert the ignition key ( 2 ) and turn it to
the position of ‘‘SEAT FUEL’’ ( 3 ).
2. Push the ‘‘FUEL’’ ( 4 ) side of the fuel lid
and seat opener switch.
3. Open the fuel lid ( 5 ).
Close the Fuel Lid:
Close the fuel lid until it locks. Make sure
the fuel lid is secure before riding.
(1) Fuel lid and
seat opener switch
(2) Ignition key
46
http://mototh.com
(3) ‘‘SEAT FUEL’’
(4) ‘‘FUEL’’
(5) Fuel lid
10/02/17 16:55:26 32KWN600_057
(5)
Seat
Open the Seat:
1. Turn the handlebar pointed straight
ahead.
2. Insert the ignition key ( 1 ) and turn it to
the position of ‘‘SEAT FUEL’’ ( 2 ).
3. Push the ‘‘SEAT’’ ( 3 ) side of the fuel lid
and seat opener switch ( 4 ).
4. Open the seat ( 5 ).
Close the Seat:
Close the seat, lower and push down until it
locks. Make sure the seat is secure before
riding.
(2)
(1)
(1) Ignition key
(2) ‘‘SEAT FUEL’’
(3) ‘‘SEAT’’
(3)
(4)
(4) Fuel lid and
seat opener switch
(5) Seat
47
http://mototh.com
10/02/17 16:55:32 32KWN600_058
RIGHT HANDLEBAR CONTROLS
Start Button ( 1 )
The start button is next to the throttle grip.
When the start button is pressed, the
starter motor cranks the engine. See page
68 for the starting procedure.
(2)
Idling Stop Switch ( 2)
Push the Idling Stop switch to activate or
deactivate the Idling Stop system.
Refer to the ‘‘IDLING STOP SYSTEM’’ on
page 52 .
(1)
(1) Start button
(2) Idling Stop switch
48
http://mototh.com
10/02/17 16:55:38 32KWN600_059
LEFT HANDLEBAR CONTROLS
Headlight Dimmer Switch ( 1)
Push the dimmer switch to
(HI) to
select high beam or to
(LO) to select
low beam.
(1)
Horn Button ( 2 )
Press the button to sound the horn.
Turn Signal Switch ( 3 )
Move to
to signal a left turn,
to
signal a right turn. Press to turn signal off.
(2)
(3)
(1) Headlight dimmer switch
(2) Horn button
(3) Turn signal switch
49
http://mototh.com
10/02/17 16:55:45 32KWN600_060
FEATURES
(Not required for operation)
STEERING LOCK
The steering can be locked when the
ignition switch ( 1 ) is in the ‘‘LOCK’’
position.
To lock
(2)
(A )
To lock the steering, turn the handlebars all
the way to the left or right, turn the ignition
key ( 2 ) to LOCK while pushing in. Remove
the key.
To unlock the steering, turn the key to OFF
while pushing in.
(B)
(C)
Do not turn the key to LOCK while riding
the scooter; loss of vehicle control will
result.
(A )
(1)
(1) Ignition switch
(2) Ignition key
50
http://mototh.com
To unlock
(A) Push in
(B) Turn to LOCK
(C) Turn to OFF
10/02/17 16:55:52 32KWN600_061
SHUTTER
The ignition switch of this scooter is
equipped with a shutter. After parking the
scooter, close the shutter f or theft
prevention.
To close the shutter, ignition key ( 1 ) is
removed, align the projection ( 2 ) of the
shutter key ( 3 ) with the slot ( 4 ) of the
shutter, and turn the shut ter key
counterclockwise or move the knob ( 5 )
upward.
To open the shutter, align the projection of
the shutter key with the slot of the shutter,
and turn the shutter key clockwise.
(3)
(4)
(1) Ignition key
(2) Projection
〈CLOSE〉
(5)
〈OPEN〉
(1)
(2)
(3) Shutter key
(4) Slot
(5) Knob
51
http://mototh.com
10/02/17 16:55:57 32KWN600_062
IDLING STOP SYSTEM
This scooter is equipped with Idling Stop
system. Idling Stop system is designed to
help reduce the fuel consumption and noise,
by idling stop while making a stop such as
waiting at an intersection.
(3)
(1)
Engine will stop by Idling Stop system, a
few seconds after the scooter is stopped,
with the throttle ( 1 ) completely closed.
While Idling Stop system is working, the
STAND BY indicator ( 2 ) flashes and the
headlights get dark.
Engine will start, when the throttle is
opened.
(2)
You can change the Idling Stop system
mode by switching the Idling Stop switch
( 3 ) (page 53 ).
(1) Throttle
(2) STAND BY indicator
(3) Idling Stop switch
52
http://mototh.com
10/02/17 16:56:03 32KWN600_063
Idling St op Syst em Operat ing
Conditions
Followings are requirements for the Idling
Stop system to operate properly.
Before riding
Put the side stand up.
Warm up the engine. Idling Stop system
does not operate, if the engine is not
warmed up.
Push the Idling Stop switch to the
‘‘IDLING STOP’’.
Ride the scooter at proper riding position.
Idling Stop system is designed not to
work when no load on the seat.
After Stopping
Close the throttle completely. Engine will
not stop if the throttle is little opened.
Stop the scooter completely. Engine will
not stop if the speed is not at 0 km/h (0
mph).
Ride the scooter at speed above 10 km/h (6
mph), to enable the Idling Stop system
under above conditions.
53
http://mototh.com
10/02/17 16:56:08 32KWN600_064
Restart the Engine
Check the STAND BY indicator. If it is
not flashing, you can’t restart the engine
with the Idling Stop system, even if you
open the throttle.
If you get off the scooter (without sitting)
while the engine is stopping by the Idling
Stop system, the STAND BY indicator
will go out, and for about 3 minutes later,
the Idling Stop system will be cancelled
and headlight will go out.
If you lower the side stand, Idling Stop
system will be cancelled.
Headlights stay on after the engine is
stopped by the Idling Stop system. The
battery may discharge and you may not be
able to restart engine.
When the battery is weak, switch the Idling
Stop switch to the ‘‘ IDLING ’’ and do not to
use the Idling Stop system. See your Honda
dealer to check the battery.
See your Honda dealer for checking the
battery as specified in the maintenance
schedule (page 90 ).
To start the engine with the STAND BY
indica t or of f , see st a r t ing pr ocedur e
(page 68 ) for standard engine starting.
54
http://mototh.com
10/02/17 16:56:14 32KWN600_065
Always follow the precautions of Idling Stop
system described below.
Do not leave the scooter while the engine
is stopped by the Idling Stop system.
When you leave the scooter, always take
the ignition key ( 1 ) with you.
Do not push down on the seat while the
engine is stopped by the Idling Stop
system.
For example, push the seat down by hand
or body, or put the luggage on the seat.
The engine will start unexpectedly if the
throttle is opened with loading on the seat.
(1)
(1) Ignition key
55
http://mototh.com
10/02/17 16:56:17 32KWN600_066
Do not put excessive luggage in the
center compartment. Luggage interfere
with the seat to close.
Idling Stop system does not operate
without closing the seat completely.
56
http://mototh.com
10/02/17 16:56:26 32KWN600_067
When the Idling Stop system does not operate properly
(Idling Stop switch is at ‘‘IDLING STOP’’ position)
When the Idling Stop system does not operate properly, perform the followings.
Symptom
Possible cause
What to do
Idling Stop switch is
Push the Idling Stop switch to ‘‘ IDLING
STOP’’.
at ‘‘IDLING’’.
Engine does not
stop by Idling
Stop system
Engine is cold.
Warm up the engine.
Scooter does not
stop completely.
Stop the scooter completely. The Idling
Stop system operates if the speed is only
at 0 km/h (0 mph).
Close the throttle completely.
T hrottle is not
closed completely.
Did not ride the
scooter after engine
start.
Ride the scooter at speeds of over 10 km/
h (6 mph). The Idling Stop system does
not operate until you ride at once.
57
http://mototh.com
10/02/17 16:56:33 32KWN600_068
Symptom
Engine does not
stop by Idling
Stop system
Possible cause
Sitting wrong
position.
Excessive luggage in
t h e c e n t e r
compartment.
PGM-FI malfunction
indicator lamp
(MIL) lights.
What to do
Ride the scooter in proper riding position.
Idling Stop system is designed not to
work when no load on the seat.
Luggage interfere with the seat to close
completely. Take out some luggage from
the center compartment to close the seat
completely.
When the PGM-FI malfunction indicator
lamp (MIL) lights, the Idling Stop system
does not operate for protection of the
engine. See your Honda dealer.
58
http://mototh.com
10/02/17 16:56:42 32KWN600_069
When the STAND BY indicator does not flash, perform the followings.
Symptom
Possible cause
What to do
Ride the scooter in proper riding position.
Riding in wrong
Idling Stop system is designed not to work
position.
when no load on the seat.
The Idling Stop system will be cancelled, if
Left the scooter
you get off the scooter for about 3 minutes
for more than 3
(without sitting properly), while the engine
minutes.
is stopped by the Idling Stop system.
Engine does not
Excessive luggage
Luggage interfere with the seat to close
start even open
in the center
completely. Take out some luggage from
the throttle
compartment.
the center compartment, to close the seat
completely.
When you put down the side stand, Idling
Side stand is down.
Stop system will be cancelled. See starting
procedure (page 68 ) for standard engine
starting.
Idling Stop switch
When you push the Idling Stop switch to
is at ‘‘IDLING’’.
the ‘‘ IDLING ’’, the Idling Stop system will
be cancelled.
59
http://mototh.com
10/02/17 16:56:47 32KWN600_070
STAND BY indicator flashes, but engine does not start, perform the followings.
Symptom
Possible cause
What to do
Engine does not
Low (or dead)
Check the battery and battery terminals. If
start even open
battery or battery
battery is weak, charge the battery.
the throttle
lead is loose.
60
http://mototh.com
10/02/17 16:56:53 32KWN600_071
HELMET HOLDER
The helmet holder ( 1 ) is on the left side
below the seat. The helmet holder is
designed to secure your helmet while
parked.
Open the seat (page 47 ).
Route the helmet wire ( 2 ) through the
helmet D-ring ( 3 ) and hook the loops of the
helmet wire onto the helmet holder.
Close the seat and lock it securely.
The helmet wire is furnished in the tool kit
(page 91 ).
Riding with a helmet attached to the
holder can interfere with the rear wheel
or suspension and could cause a
crash in which you can be seriously
hurt or killed.
Use the helmet holder only while
parked. Do not ride with a helmet
secured by the holder.
(1)
(2)
(3)
(1) Helmet holder
(2) Helmet wire
(3) D-ring
61
http://mototh.com
10/02/17 16:56:59 32KWN600_072
CENTER COMPARTMENT
The center compartment ( 1 ) is below the
seat. Opening and closing:
See ‘‘FUEL LID AND SEAT OPENER
SWITCH’’ (page 47 ).
(1)
MAXIMUM WEIGHT LIMIT:
10 kg (22 lb)
Never exceed the maximum weight limit;
handling and stability may be severely
affected.
The center compartment may become
heated by the engine. Do not store food and
other articles which are flammable or
susceptible to heat damage in this
compartment.
Do not direct water under pressure against
the center compartment as water will be
forced into the compartment.
(1) Center compartment
62
http://mototh.com
10/02/17 16:57:04 32KWN600_073
DOCUMENT COMPARTMENT
The document bag ( 1 ) is in the document
compartment ( 2 ) in the center
compartment ( 3 ).
Open the seat (page 47 ).
This owner’s manual and other documents
should be stored in the document bag.
When washing your scooter, be careful not
to flood this area with water.
(1)
(3)
(2)
(1) Document bag
(2) Document compartment
(3) Center compartment
63
http://mototh.com
10/02/17 16:57:11 32KWN600_074
GLOVE BOX
The glove box ( 1 ) is provided below the
handlebar.
MAXIMUM WEIGHT LIMIT:
1.0 kg (2.2 lb)
(3)
Never exceed the maximum weight limit;
handling and stability may be severely
affected.
To open the glove box, pull the knob ( 2 ) up.
Make sure the box lid ( 3 ) is closed before
riding.
Do not store valuables or fragile articles in
the glove box.
(2)
When washing your scooter be careful not
to flood this area with water.
(1) Glove box
(2) Knob
(3) Box lid
64
http://mototh.com
(1)
10/02/17 16:57:15 32KWN600_075
HEA DL IGHT AIM VERTICAL
ADJUSTMENT
Vertical adjustment can be made by turning
the screw ( 1 ) in or out as necessary.
Obey local laws and regulations.
(B)
(A )
(1) Screw
(1)
(A) Up
(B) Down
65
http://mototh.com
10/02/17 16:57:21 32KWN600_076
CLIP
Removal:
Press down on the center pin to release
the lock.
Pull out the clip from the hole.
Installation:
Slightly open the retaining pawls and then
push them out.
Insert the clip into the hole.
Lightly press down on the center pin to
lock the clip.
66
http://mototh.com
10/02/17 16:57:32 32KWN600_077
OPERATION
PRE-RIDE INSPECTION
For your safety, it is very important to take
a few moments before each ride to walk
around your scooter and check its condition.
If you detect any problem, be sure you take
care of it, or have it corrected by your
Honda dealer.
Improperly maintaining this scooter or
failing to correct a problem before
riding can cause a crash in which you
can be seriously hurt or killed.
Always perform a pre-ride inspection
before every ride and correct any
problems.
1. Engine oil level− add engine oil if
required (page 38 ). Check for leaks.
2. Fuel level−fill fuel tank when necessary
(page 35 ). Check for leaks.
3. Coolant level−add coolant if required.
Check for leaks (pages 33 − 34 ).
4. Brakes−check operation;
Front: Make sure there is no brake fluid
leakage (pages 28 − 29 ).
Rear: Adjust freeplay if necessary (pages
30 − 32 ).
5. Tyres−check condition and pressure
(pages 39 − 44 ).
6. Throttle−check for smooth opening and
full closing in all steering positions.
7. Lights and horn−check that headlight,
brake/tail light, position light, license
light, turn signals, indicators and horn
function properly.
8. Side stand ignition cut-off system−check
for proper function (page 108 ).
67
http://mototh.com
10/02/17 16:57:38 32KWN600_078
STARTING THE ENGINE
Always follow the proper starting procedure
described below.
This scooter has an automatic fuel valve.
This scooter is equipped with a side stand
ignition cut-off system. The engine cannot
be started if the side stand is down. A
running engine will shut off if the side stand
is lowered.
To protect the catalytic converter in your
scooter’s exhaust system, avoid extending
idling and the use of leaded petrol.
Your scooter’s exhaust contains poisonous
carbon monoxide gas. High levels of carbon
monoxide can collect rapidly in enclosed
areas such as a garage. Do not run the
engine with the garage door closed. Even
with the door open, run the engine only
long enough to move your scooter out of
the garage.
Do not use the electric starter for more than
5 seconds at a time. Release the start button
for approximately 10 seconds before
pressing it again.
If the scooter is over-turned, you must first
turn the ignition switch to the OFF position
and then inspect the scooter carefully.
Refer to the ‘‘TAKING CARE OF THE
UNEXPECTED’’ on page 131 .
68
http://mototh.com
10/02/17 16:57:42 32KWN600_079
This scooter has a fuel-injected engine with
an automatic choke. Follow the procedure
indicated below.
1. Place the scooter on its center stand.
2. Lock the rear wheel by squeezing the
rear brake lever ( 1 ).
The electric starter will only work when the
rear brake lever is squeezed and the side
stand is up.
(1)
(1) Rear brake lever
69
http://mototh.com
10/02/17 16:57:49 32KWN600_080
3. Turn the ignition switch ( 2 ) to ON.
Confirm the following:
The PGM-FI malfunction indicator lamp
(MIL) is OFF.
The high coolant temperature indicator is
OFF.
4. With the throttle completely closed, press
the start button ( 3 ). Release the start
button as soon as the engine starts.
The engine will not start if the throttle is
fully open (because the electronic control
module cuts off the fuel supply).
(2)
(3)
(2) Ignition switch
(3) Start button
70
http://mototh.com
10/02/17 16:57:55 32KWN600_081
5. Be sure to keep the throttle closed and
the rear brake lever locked while starting
and warming up the engine.
6. Allow the engine to warm up before
riding (See ‘‘RIDING’’, page 74 ).
To use the Idling Stop system, push the
Idling Stop switch ( 4 ) to ‘‘ IDLING STOP ’’
(see ‘‘IDLING STOP SYSTEM’’, page 52 ).
(4)
Do not ‘‘BLIP’’ the throttle (open and close
rapidly) as the scooter will move forward
suddenly, causing possible loss of control.
Do not leave the scooter unattended while
the engine is warming up.
CLOSE
(4) Idling Stop switch
71
http://mototh.com
10/02/17 16:57:59 32KWN600_082
Flooded Engine
If the engine fails to start after repeated
attempts, it may be flooded.
1. Open the throttle fully.
2. Press the start button for 5 seconds.
3. Follow the normal starting procedure.
4. If the engine starts with unstable idle,
open the throttle slightly.
If the engine does not start, wait for 10
seconds, then follow steps 1−3 again.
72
http://mototh.com
10/02/17 16:58:02 32KWN600_083
RUNNING-IN
Help assure your scooter’s future reliability
and performance by paying extra attention
to how you ride during the first 500 km (300
miles).
During this period, avoid full-throttle starts
and rapid acceleration.
73
http://mototh.com
10/02/17 16:58:07 32KWN600_084
RIDING
Review Scooter Safety (pages 1 − 14 )
before you ride.
1. Make sure the throttle is closed and
the rear wheel is locked by squeezing
the rear brake lever before moving the
scooter off the center stand.
The rear wheel must be locked when
moving the scooter off the center stand
or loss of control may result.
Make sure flammable materials such as dry
grass or leaves do not come in contact with
the exhaust system when riding, idling, or
parking your scooter.
(1)
(1) Rear brake lever
74
http://mototh.com
10/02/17 16:58:12 32KWN600_085
2. Stand on the left side of the scooter
and push it forward and off the center
stand.
3. Mount the scooter f rom the left side
keeping at least one foot on the ground to
steady the scooter.
75
http://mototh.com
10/02/17 16:58:16 32KWN600_086
4. Release the rear brake lever ( 1 ).
(1)
5. Bef ore starting of f , indicate your
direction with the turn signals, and check
for safe traffic conditions.
Grasp the handlebars firmly with both
hands.
Never attempt one-handed operation; loss
of vehicle control could result.
(1) Rear brake lever
76
http://mototh.com
10/02/17 16:58:21 32KWN600_087
6. To accelerate, open the throttle ( 2 )
gradually; the scooter will move forward.
OPEN
Do not ‘‘BLIP’’ the throttle (open and
close rapidly) as the scooter will move
forward suddenly, causing possible loss
of control.
CLOSE
(2)
7. To decelerate, close the throttle.
(2) Throttle
77
http://mototh.com
10/02/17 16:58:25 32KWN600_088
8. When slowing down the scooter,
coordination of the throttle ( 2 ) and front
and rear brakes ( 3 ) is most important.
Both front and rear brakes should be
applied together. Independent use of only
the front or rear brake reduces stopping
performance.
Excessive brake application may cause
either wheel to lock, reducing control of
the scooter.
(2)
(3)
(3) Front and rear brakes
(2) Throttle
78
http://mototh.com
(3)
10/02/17 16:58:30 32KWN600_089
9. When approaching a corner or turn,
close the throttle ( 2 ) fully, and slow the
scooter down by applying both front and
rear brakes ( 3 ) at the same time.
10. Af ter completing the turn, open the
throttle gradually to accelerate the
scooter.
(2)
(3)
(3)
(2) Throttle
(3) Front and rear brakes
79
http://mototh.com
10/02/17 16:58:35 32KWN600_090
11. When descending a steep grade, close
the throttle ( 2 ) fully and apply both
brakes ( 3 ) to slow the scooter.
Avoid continuous use of the brakes, which
may result in overheating and reduction of
braking efficiency.
(2)
(3)
(2) Throttle
(3) Front and rear brakes
80
http://mototh.com
(3)
10/02/17 16:58:43 32KWN600_091
12. When riding on wet or loose surfaces,
be especially cautious.
When riding in wet or rainy conditions or
on loose surfaces, the ability to maneuver
and stop will be reduced. For your safety:
Exercise extreme caution when
braking, accelerating or turning.
Ride at slower speeds and allow for
extra stopping distance.
Keep the scooter as upright as possible.
Use extreme caution when riding over
slippery surfaces such as railroad
tracks, iron plates, manhole covers,
painted lines, etc.
When the Idling Stop switch is at
‘‘IDLING STOP’’
Engine will stop by the Idling Stop system,
a few seconds after the scooter is stopped,
with the throttle completely closed.
While the Idling Stop system is working,
the STAND BY indicator ( 4 ) flashes.
Headlights get dark but stay on after the
engine is stopped by the Idling Stop
system.
Stopping by the Idling Stop system for a
long time may cause battery discharge.
(4)
(4) STAND BY indicator
81
http://mototh.com
10/02/17 16:58:49 32KWN600_092
Restart the engine
To restart the engine, open the throttle.
Engine will not start without riding in
proper position.
Make sure the engine is started.
When starting on a hill, release the brake
lever after making sure the feeling of
scooter moving.
While the engine is stopping by the Idling
Stop system, push the Idling Stop switch
to the ‘‘IDLING’’ to cancel the Idling Stop
system.
If the engine does not start even open the
throttle, the battery may discharge. See
your Honda dealer for checking the
battery.
See your Honda dealer for checking the
battery as specified in the maintenance
schedule (page 90 ).
82
http://mototh.com
10/02/17 16:58:56 32KWN600_093
PARKING
1. After stopping the scooter turn the
ignition switch to the ‘‘OFF’’ position and
remove the key.
2. Use the center stand to support the
scooter while parked.
3. Lock the steering to help prevent theft
(page 50 ).
4. Close the shutter to help prevent theft
(page 51 ).
Park the scooter on firm, level ground to
prevent it from falling over.
If you must park on a slight incline, aim the
front of the scooter uphill to reduce the
possibility of rolling off the center stand or
overturning.
The exhaust pipe and muffler become
very hot during operation and remain
sufficiently hot to inflict burns if touched
even after shutting off the engine.
Make sure flammable materials such as
dry grass or leaves do not come in contact
with the exhaust system when parking
your scooter.
HOW TO USE CENTER STAND
83
http://mototh.com
10/02/17 16:59:01 32KWN600_094
ANTI-THEFT TIPS
1. Always lock the steering and never leave
the key in the ignition switch. This
sounds simple but people do forget.
2. Be sure the registration information for
your scooter is accurate and current.
3. Park your scooter in a locked garage
whenever possible.
4. Use an additional anti-theft device of
good quality.
5. Put your name, address, and phone
number in this Owner’s Manual and keep
it on your scooters at all times.
Many times stolen scooters are identified
by information in the Owner’s Manuals
that are still with them.
LOCK STEERING
(1)
(A )
(B)
NAME:
ADDRESS:
(1) Ignition key
PHONE NO:
84
http://mototh.com
(A) Push in
(B) Turn to LOCK
10/02/17 16:59:06 32KWN600_095
MAINTENANCE
THE IMPORTANCE OF
MAINTENANCE
A well-maintained scooter is essential for
safe, economical and trouble-free riding. It
will also help reduce air pollution.
If your scooter overturns or becomes
involved in a crash, be sure your Honda
dealer inspects all major parts, even if you
are able to make some repairs.
To help you properly care for your scooter,
the following pages include a Maintenance
Schedule and a Maintenance Record for
regularly scheduled maintenance.
These instructions are based on the
assumption that the scooter will be used
exclusively for its designed purpose.
Sustained high speed operation or operation
in unusually wet or dusty conditions will
require more f requent service than
specified in the Maintenance Schedule.
Consult your Honda dealer f or
recommendations applicable to your
individual needs and use.
Improperly maintaining this scooter or
failing to correct a problem before you
ride can cause a crash in which you
can be seriously hurt or killed.
Always follow the inspection and
maintenance recommendations and
schedules in this owner’s manual.
85
http://mototh.com
10/02/17 16:59:10 32KWN600_096
MAINTENANCE SAFETY
This section includes instructions on some
important maintenance tasks. You can
perform some of these tasks with the tools
provided − if you have basic mechanical
skills.
Other tasks that are more difficult and
require special tools are best performed by
prof essionals. Wheel removal should
normally be handled only by a Honda
technician or other qualified mechanic;
instructions are included in this manual only
to assist in emergency service.
Some of the most important saf ety
precautions follow. However, we cannot
warn you of every conceivable hazard that
can arise in performing maintenance. Only
you can decide whether or not you should
perform a given task.
86
http://mototh.com
Failure to properly follow maintenance
instructions and precautions can
cause you to be seriously hurt or killed.
Always follow the procedures and
precautions in this owner’s manual.
10/02/17 16:59:15 32KWN600_097
SAFETY PRECAUTIONS
Make sure the engine is off before you
begin any maintenance or repairs. This
will help eliminate several potential
hazards:
Carbon monoxide poisoning from
engine exhaust.
Be sure there is adequate ventilation
whenever you operate the engine.
Burns from hot parts.
Let the engine and exhaust system cool
before touching.
Injury from moving parts.
Do not run the engine unless instructed
to do so.
Read the instructions before you begin,
and make sure you have the tools and
skills required.
To help prevent the scooter from falling
over, park it on a firm, level surface, using
the center stand to provide support.
To reduce the possibility of a fire or
explosion, be careful when working
around petrol or batteries. Use only
nonflammable solvent, not petrol, to clean
parts. Keep cigarettes, sparks and flames
away from the battery and all fuel-related
parts.
Remember that your Honda dealer knows
your scooter best and is fully equipped to
maintain and repair it.
To ensure the best quality and reliability,
use only new Honda Genuine Parts or their
equivalents for repair and replacement.
87
http://mototh.com
10/02/17 16:59:22 32KWN600_098
MAINTENANCE SCHEDULE
Perform the Pre-ride Inspection (page 67 ) at each scheduled maintenance period.
I: INSPECT AND CLEAN, ADJUST, LUBRICATE OR REPLACE IF NECESSARY
C: CLEAN R: REPLACE A: ADJUST L: LUBRICATE
The following items require some mechanical knowledge. Certain items (particularly those marked * and ** ) may
require more technical information and tools. Consult your Honda dealer.
Should be serviced by your Honda dealer, unless the owner has proper tools and service data and is mechanically
qualified. Refer to the Official Honda Shop Manual.
In the interest of safety, we recommend these items be serviced only by your Honda dealer.
Honda recommends that your Honda dealer should road test your scooter after each periodic maintenance is carried
out.
NOTES: (1) At higher odometer readings, repeat at the frequency interval established here.
(2) Service more frequently when riding in unusually wet or dusty areas.
(3) Service more frequently when riding in rain or at full throttle.
(4) Replace every 2 years. Replacement requires mechanical skill.
88
http://mototh.com
10/02/17 16:59:28 32KWN600_099
FREQUENCY
ITEM
FUEL LINE
THROTTLE OPERATION
AIR CLEANER
CRANKCASE BREATHER
SPARK PLUG
VALVE CLEARANCE
ENGINE OIL
ENGINE OIL STRAINER SCREEN
ENGINE IDLE SPEED
RADIATOR COOLANT
COOLING SYSTEM
WHICHEVER →
COMES
× 1,000 km
FIRST
× 1,000 mi
↓
MONTH
NOTE
NOTE (2)
NOTE (3)
NOTE (4)
ODOMETER READING [NOTE (1)]
1
0.6
4
2.5
6
I
I
8
5
12
I
I
12
7.5
18
I
I
EVERY 16,000 km (10,000 mi) R
C
I
R
I
I
I
C
R
I
R
I
I
I
C
I
C
I
Refer
to
page
−
107
95
96
103
−
97
101
−
33
−
89
http://mototh.com
10/02/17 16:59:36 32KWN600_100
FREQUENCY
ITEM
DRIVE BELT
FINAL DRIVE OIL
BATTERY
BRAKE FLUID
BRAKE SHOES/PADS WEAR
BRAKE SYSTEM
BRAKE LIGHT SWITCH
BRAKE LOCK OPERATION
HEADLIGHT AIM
CLUTCH SHOES WEAR
SIDE STAND
SUSPENSION
NUTS, BOLTS, FASTENERS
WHEELS/TYRES
STEERING HEAD BEARINGS
WHICHEVER →
COMES
× 1,000 km
FIRST
× 1,000 mi
↓
MONTH
NOTE
ODOMETER READING [NOTE (1)]
1
0.6
4
2.5
6
8
5
12
12
7.5
18
EVERY 8,000 km (5,000 mi) I,
EVERY 24,000 km (15,000 mi) R
NOTE (4)
I
NOTE (4)
I
I
I
I
I
I
I
I
I
I
I
I
I
I
90
http://mototh.com
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
Refer
to
page
−
−
111
28
109, 110
27, 109, 110
−
−
65
−
108
107
−
−
−
10/02/17 16:59:42 32KWN600_101
TOOL KIT
The tool kit ( 1 ) is in the tool kit
compartment ( 2 ) under the seat (page 47 ).
Some roadside repairs, minor adjustments
and parts replacement can be performed
with the tools contained in the kit.
Standard/Phillips screwdriver
Screwdriver handle
Spark plug wrench
Helmet wire
Tool bag
(1)
(2)
(1) Tool kit
(2) Tool kit compartment
91
http://mototh.com
10/02/17 16:59:48 32KWN600_102
SERIAL NUMBERS
The frame and engine serial numbers are
required when registering your scooter.
They may also be required by your dealer
when ordering replacement parts.
Record the numbers here f or your
reference.
FRAME NO.
The frame number ( 1 ) is stamped on the
rear of the frame below the seat.
The engine number ( 2 ) is stamped on the
lower left side of the crankcase.
ENGINE NO.
(1)
(2)
(1) Frame number
(2) Engine number
92
http://mototh.com
10/02/17 16:59:53 32KWN600_103
This scooter has two keys ( 1 ) and a key
number plate ( 2 ).
You will need the key number if you ever
have to replace a key. Store the plate in a
safe place.
To reproduce keys, bring all keys, key
number plate and scooter to your Honda
dealer.
(1)
(2)
(1) Key
(2) Key number plate
93
http://mototh.com
10/02/17 16:59:57 32KWN600_104
COLOUR LABEL
The colour label ( 1 ) is attached to the
center compartment (page 62 ).
It is helpful when ordering replacement
parts. Record the colour and code here for
your reference.
COLOUR
CODE
(1)
(1) Colour label
94
http://mototh.com
10/02/17 17:00:06 32KWN600_105
AIR CLEANER
Refer to the Safety Precautions on page 87 .
The air cleaner should be serviced at
regular intervals (page 89 ). Service more
frequently when riding in unusually wet or
dusty areas.
1. Remove the air cleaner housing cover ( 1 )
by removing the screws ( 2 ).
2. Remove and discard the air cleaner
element ( 3 ).
3. Thoroughly clean the inside of the air
cleaner housing ( 4 ).
4. Install the new air cleaner element.
Use the Honda Genuine air cleaner
element or an equivalent air cleaner
element specified for your model. Using
the wrong Honda air cleaner element or a
non-Honda air cleaner element which is
not of equivalent quality may cause
premature engine wear or performance
problems.
5. Install the removed parts in the reverse
order of removal.
(1)
(4)
(2)
(2)
(2)
(3)
(1) Air cleaner housing cover
(2) Screws
(3) Air cleaner element
(4) Air cleaner housing
95
http://mototh.com
10/02/17 17:00:11 32KWN600_106
CRANKCASE BREATHER
Refer to the Safety Precautions on page 87 .
1. Remove the crankcase breather tube ( 1 )
from the air cleaner housing and drain
deposits into a suitable container.
2. Reinstall the crankcase breather tube.
Service more frequently when riding in rain,
at full throttle, or after the scooter is
washed or overturned. Service if the deposit
level can be seen in the transparent section
of the drain tube.
(1)
(1) Crankcase breather tube
96
http://mototh.com
10/02/17 17:00:22 32KWN600_107
ENGINE OIL
Refer to the Safety Precautions on page 87 .
Oil Recommendation
API
classification
SG or higher except
oils labeled as
energy conserving
on the circular API
service label
Viscosity
SAE 10W-30
JASO T 903
standard
MB
Your scooter does not need oil additives.
Use the recommended oil.
Do not use API SH or higher oils displaying
a circular API ‘‘energy conserving’’ service
label on the container. They may affect
lubrication and clutch performance.
NOT RECOMMENDED
OK
Do not use non-detergent, vegetable, or
castor based racing oils.
Suggested Oil
Honda ‘‘4-STROKE MOTORCYCLE
OIL’’ or equivalent.
97
http://mototh.com
10/02/17 17:00:28 32KWN600_108
Viscosity:
Viscosity grade of engine oil should be
based on average atmospheric temperature
in your riding area. The following provides a
guide to the selection of the proper grade or
viscosity of oil to be used at various
atmospheric temperatures.
JASO T 903 standard
The JASO T 903 standard is an index for
engine oils for 4-stroke motorcycle engines.
There are two classes: MA and MB.
Oil conforming to the standard is labeled on
the oil container. For example, the following
label shows the MB classification.
(1)
(2)
(1) Code number of the sales company
of the oil
(2) Oil classification
98
http://mototh.com
10/02/17 17:00:34 32KWN600_109
Engine Oil
Engine oil quality is the chief factor
affecting engine service life. Change the
engine oil as specified in the maintenance
schedule (page 89 ).
When running in very dusty conditions, oil
changes should be perf ormed more
f requently than specif ied in the
maintenance schedule.
Please dispose of used engine oil in a
manner that is compatible with the
environment. We suggest you take it in a
sealed container to your local recycling
center or service station for reclamation. Do
not throw it in the trash or pour it on the
ground or down a drain.
Changing the oil requires a torque wrench.
If you do not have it and the necessary skill,
we recommend that you have your Honda
dealer perform this service.
If a torque wrench is not used for this
installation, see your Honda dealer as soon
as possible to verify proper assembly.
Change the engine oil with the engine at
normal operating temperature and the
scooter on its center stand to assure
complete and rapid draining.
Change the engine oil with the Idling Stop
switch ‘‘IDLING’’.
Used engine oil may cause skin cancer if
repeatedly left in contact with the skin for
prolonged periods. Although this is unlikely
unless you handle used oil on a daily basis,
it is still advisable to thoroughly wash your
hands with soap and water as soon as possible after handling used oil.
99
http://mototh.com
10/02/17 17:00:40 32KWN600_110
1. Place an oil drain pan under the
crankcase. Remove the oil fill cap/
dipstick, oil drain bolt ( 1 ) and sealing
washer ( 2 ).
2. Check that the sealing washer on the
drain bolt is in good condition and install
the bolt. Replace the sealing washer
every other time the oil is changed, or
each time if necessary.
Oil drain bolt torque:
24 N·m (2.4 kgf·m , 18 lbf·ft)
3. Fill the crankcase with the recommended
grade oil; approximately:
0.8 (0.8 US qt , 0.7 Imp qt)
4. Reinstall the oil fill cap/dipstick.
5. Start the engine and let it idle for 3−5
minutes.
6. Stop the engine and wait 2−3 minutes.
Check that the oil level is at the upper
level mark on the oil fill cap/dipstick with
the scooter upright on firm, level ground.
Make sure there are no oil leaks.
(1)
(1) Oil drain bolt
100
http://mototh.com
(2)
(2) Sealing washer
10/02/17 17:00:48 32KWN600_111
ENGINE OIL STRAINER SCREEN
Refer to the Safety Precautions on page 87 .
1. Drain the engine oil (page 100 ).
2. Remove the oil strainer screen cap ( 1 ).
(3) (2)
(4) (1)
3. The spring ( 2 ) and oil strainer screen
( 3 ) will come out when the oil strainer
screen cap is removed.
4. Clean the oil strainer screen.
5. Check that the oil strainer screen, sealing
rubber and O-ring ( 4 ) are in good
condition.
(1) Oil strainer screen cap
(2) Spring
(3) Oil strainer screen
(4) O-ring
101
http://mototh.com
10/02/17 17:00:55 32KWN600_112
6. Install the oil strainer screen, spring and
oil strainer screen cap.
Oil strainer screen cap torque:
20 N·m (2.0 kgf·m , 15 lbf·ft)
7. Check that the sealing washer on the
drain bolt is in good condition and install
the bolt. Replace the sealing washer
every other time the oil is changed, or
each time if necessary.
Oil drain bolt torque:
24 N·m (2.4 kgf·m , 18 lbf·ft)
8. Fill the crankcase with the recommended
grade oil; approximately:
0.9 (1.0 US qt , 0.8 Imp qt)
9. Install the oil fill cap/dipstick.
10. Start the engine and let it idle for 3−5
minutes.
11. 2−3 minutes after stopping the engine,
check that the oil level is at the upper
level mark on the oil fill cap/dipstick with
the scooter upright on firm, level ground.
Make sure there are no oil leaks.
If a torque wrench is not used for this
installation, see your Honda dealer as soon
as possible to verify proper assembly.
102
http://mototh.com
10/02/17 17:01:01 32KWN600_113
SPARK PLUG
Refer to the Safety Precautions on page 87 .
1. Remove the plug maintenance lid ( 1 ) by
removing the screw ( 2 ).
Recommended plugs:
Standard:
CPR7EA-9 (NGK)
(2)
Never use a spark plug with an improper
heat range. Severe engine damage could
result.
(1)
(1) Plug maintenance lid
(2) Screw
103
http://mototh.com
10/02/17 17:01:08 32KWN600_114
2. Disconnect the spark plug cap ( 3 ) from
the spark plug.
3. Clean any dirt from around the spark plug
base.
Remove the spark plug using a spark plug
wrench furnished in the tool kit.
(3)
4. Inspect the electrodes and center
porcelain for deposits, erosion or carbon
fouling. If the erosion or deposit is heavy,
replace the plug. Clean a carbon or wetfouled plug with a plug cleaner, otherwise
use a wire brush.
5. Check the spark plug gap ( 4 ) using a
wire-type feeler gauge. If adjustment is
necessary, bend the side electrode ( 5 )
carefully.
The gap should be:
0.80−0.90 mm (0.031−0.035 in)
(4)
(5)
(3) Spark plug cap
(4) Spark plug gap
104
http://mototh.com
(5) Side electrode
10/02/17 17:01:15 32KWN600_115
6. Make sure the plug washer is in good
condition.
7. With the plug washer attached, thread
the spark plug in by hand to prevent
cross-threading.
8. Tighten the spark plug:
If the old plug is good:
1/8 turn after it seats.
If installing a new plug, tighten it twice
to prevent loosening:
a) First, tighten the plug:
NGK: 1/2 turn after it seats.
b) Then loosen the plug.
c) Next, tighten the plug again:
1/8 turn after it seats.
10. Install the removed parts in the reverse
order of removal.
An improperly tightened spark plug can
damage the engine. If a plug is too loose, a
piston may be damaged. If a plug is too tight,
the threads may be damaged.
9. Reinstall the spark plug cap. Take care to
avoid pinching any cables or wires.
105
http://mototh.com
10/02/17 17:01:19 32KWN600_116
COOLANT
Refer to the Safety Precautions on page 87 .
Coolant Replacement
Coolant should be replaced by a Honda
dealer, unless the owner has proper tools
and service data and is mechanically
qualified. Refer to an official Honda Shop
Manual.
Always add coolant to the reserve tank. Do
not attempt to add coolant by removing the
radiator cap.
106
http://mototh.com
Removing the radiator cap while the
engine is hot can cause the coolant to
spray out, seriously scalding you.
Always let the engine and radiator cool
down before removing the radiator cap.
10/02/17 17:01:25 32KWN600_117
THROTTLE OPERATION
Refer to the Safety Precautions on page 87 .
Check for smooth rotation of the throttle
grip from the fully open to the fully closed
position at both full steering positions.
FRONT AND REAR SUSPENSION
INSPECTION
Refer to the Safety Precautions on page 87 .
1. Check the front fork assembly by locking
the front brake and pumping the fork up
and down vigorously. Suspension action
should be smooth and there must be no
oil leakage.
2. Engine hanger bushing−this can be
checked by pushing hard against the side
of the rear wheel while the scooter is on
the center stand and feeling for looseness
of the engine hanger bushings.
3. Carefully inspect all front and rear
suspension fasteners for tightness.
107
http://mototh.com
10/02/17 17:01:32 32KWN600_118
SIDE STAND
Refer to the Safety Precautions on page 87 .
Perform the following maintenance in
accordance with the maintenance schedule.
Functional Check:
Check the side stand spring ( 1 ) for
damage or loss of tension and the side
stand assembly for freedom of movement.
Check the side stand ignition cut-off
system:
1. Place the scooter on its center stand.
2. Put the side stand up and start the
engine.
3. Lower the side stand. The engine
should stop as you put the side stand
down.
If the side stand system does not operate as
described, see your Honda dealer for
service.
(1)
(1) Side stand spring
108
http://mototh.com
10/02/17 17:01:37 32KWN600_119
BRAKE PAD WEAR
Refer to the Safety Precautions on page 87 .
〈FRONT BRAKE〉
Brake pad wear depends upon the severity
of usage, the type of riding, and road
conditions. (Generally, the pads will wear
faster on wet and dirty roads.)
Inspect t he pa ds a t e ach r egular
maintenance interval (page 90 ).
Front Brake
Check the wear indicator marks ( 1 ) on
each pad.
If either pad is worn to the wear indicator
mark, replace both pads as a set. See your
Honda dealer for this service.
(1)
(1) Wear indicator marks
109
http://mototh.com
10/02/17 17:01:43 32KWN600_120
BRAKE SHOE WEAR
Refer to the Safety Precautions on page 87 .
〈REAR BRAKE〉
(4)
(1)
The rear brake is equipped with a brake
wear indicator.
When the brake is applied, an arrow ( 1 )
attached to the brake arm ( 2 ) moves
toward a reference mark ( 3 ) on the brake
panel ( 4 ). If the arrow aligns with the
reference mark on full application of the
brake, the brake shoes must be replaced.
See your Honda dealer for this service.
(2)
When the brake service is necessary, see
your Honda dealer. Use only Honda
Genuine Parts or its equivalent.
(3)
(1) Arrow
(2) Brake arm
110
http://mototh.com
(3) Reference mark
(4) Brake panel
10/02/17 17:01:49 32KWN600_121
BATTERY
Refer to the Safety Precautions on page 87 .
It is not necessary to check the battery
electrolyte level or add distilled water as the
battery is a maintenance-free (sealed) type.
If your battery seems weak and/or is
leaking electrolyte (causing hard starting or
other electrical troubles), contact your
Honda dealer.
An improperly disposed of battery can be
harmful to the environment and human
health.
Always confirm local regulations for battery
disposal.
Your battery is a maintenance-free type and
can be permanently damaged if the cap strip
is removed.
This symbol on the battery means
that this product must not be
treated as household waste.
The battery gives off explosive
hydrogen gas during normal operation.
A spark or flame can cause the battery
to explode with enough force to kill or
seriously hurt you.
Wear protective clothing and a face
shield, or have a skilled mechanic do
the battery maintenance.
111
http://mototh.com
10/02/17 17:01:55 32KWN600_122
Headlights stay on after the engine is
stopped by the Idling Stop system.
The battery may discharge and you may not
be able to restart engine. When the battery
is weak, switch the Idling Stop switch to
‘‘IDLING’’ and do not to use the Idling Stop
system. See your Honda dealer to check the
battery.
Removal:
1. Make sure the ignition switch is OFF.
2. Open the seat (page 47 ).
3. Remove the battery cover ( 1 ) by
removing the clip ( 2 ).
(1)
See your Honda dealer for checking the
battery as specified in the maintenance
schedule (page 90 ).
(2)
(1) Battery cover
(2) Clip
112
http://mototh.com
10/02/17 17:02:02 32KWN600_123
4. Remove the battery holder ( 3 ).
5. Disconnect the negative (−) terminal
lead ( 4 ) from the battery first, then
disconnect the positive (+) terminal lead
( 5 ).
6. Remove the battery ( 6 ).
(5)
Installation:
1. Reinstall in the reverse order of removal.
Be sure to connect the positive (+)
terminal first, then the negative (−)
terminal.
2. Check all bolts and other fasteners are
secure.
(3)
(6)
(4)
(3) Battery holder
(4) Negative (−) terminal lead
(5) Positive (+) terminal lead
(6) Battery
113
http://mototh.com
10/02/17 17:02:06 32KWN600_124
FUSE REPLACEMENT
Refer to the Safety Precautions on page 87 .
Blown fuse
When frequent fuse failure occurs, it
usually indicates a short circuit or an
overload in the electrical system. See your
Honda dealer for repair.
Never use a fuse with a different rating
from that specified. Serious damage to the
electrical system or a fire may result,
causing a dangerous loss of lights or engine
power.
114
http://mototh.com
10/02/17 17:02:14 32KWN600_125
Fuse Box:
The fuse box ( 1 ) is located near the battery.
The specified fuses are:
Main fuse 1 10A
Main fuse 2 30A
10A, 15A
Sub fuse
1. Remove the battery cover (page 112 ).
2. Open the fuse box cover ( 2 ).
3. Pull out the old fuse and install a new fuse.
The spare fuses ( 3 ) are located in the
fuse box.
4. Close the fuse box cover and install the
battery cover.
(3)
(1)
(2)
(1) Fuse box
(2) Fuse box cover
(3) Spare fuses
115
http://mototh.com
10/02/17 17:02:20 32KWN600_126
BULB REPLACEMENT
Refer to the Safety Precautions on page 87 .
The light bulb becomes very hot while the
light is ON, and remains hot for a while
after it is turned OFF. Be sure to let it cool
down before servicing.
Do not put finger prints on the headlight
bulb, as they may create hot spots on the
bulb and cause it to break.
Wear clean gloves while replacing the bulb.
If you touch the bulb with your bare hands,
clean it with a cloth moistened with alcohol
to prevent its early failure.
116
http://mototh.com
Be sure to turn the ignition switch OFF
when replacing the bulb.
Do not use bulbs other than those
specified.
After installing a new bulb, check that the
light operates properly.
10/02/17 17:02:27 32KWN600_127
Headlight Bulb
1. Pull back the rubber dust cover ( 1 ).
2. Turn the bulb ( 2 ) counterclockwise, and
remove it.
3. Remove the bulb from the connector ( 3 ).
4. Install a new bulb in the reverse order of
removal.
Install the rubber dust cover with its
‘‘TOP’’ mark ( 4 ) facing up.
(4)
(1)
(2)
(3)
(1) Rubber dust cover
(2) Bulb
(3) Connector
(4) ‘‘TOP’’ mark
117
http://mototh.com
10/02/17 17:02:33 32KWN600_128
Position Light Bulb
The right and left position light bulbs
replacement can be done in the same way.
1. Turn the socket ( 1 ) counterclockwise,
and remove it.
2. Pull out the bulb ( 2 ) without turning.
3. Install a new bulb in the reverse order of
removal.
(1)
(1) Socket
(2) Bulb
118
http://mototh.com
(2)
10/02/17 17:02:38 32KWN600_129
Brake/Tail Light Bulb
1. Remove the screws ( 1 ).
2. While the rear cover ( 2 ) pressing as
illustration, unhook the prongs ( 3 ), from
the front side of the rear cover.
3. Remove the rear cover.
(1)
(3)
(3)
(2)
(3)
(3)
(2)
(3)
(1) Screws
(2) Rear cover
(3) Prongs
119
http://mototh.com
10/02/17 17:02:43 32KWN600_130
4. Turn the socket ( 4 ) counterclockwise,
and remove it.
5. Slightly press the bulb ( 5 ) and turn it
counterclockwise.
6. Install a new bulb in the reverse order of
removal.
(4)
(5)
(4) Socket
(5) Bulb
120
http://mototh.com
10/02/17 17:02:49 32KWN600_131
Front Turn Signal Bulb
The right and left turn signal bulbs
replacement can be done in the same way.
1. Turn the socket ( 1 ) counterclockwise,
and remove it.
2. Slightly press the bulb ( 2 ) and turn it
counterclockwise.
3. Install a new bulb in the reverse order of
removal.
Use only the amber bulb.
(1)
(2)
(1) Socket
(2) Bulb
121
http://mototh.com
10/02/17 17:02:57 32KWN600_132
Rear Turn Signal Bulb
The right and left turn signal bulbs
replacement can be done in the same way.
(1)
(5)
1. Remove the turn signal assembly ( 1 ) by
removing the screws ( 2 ).
2. Unhook the hook ( 3 ) and remove the
turn signal lens ( 4 ) from the turn signal
assembly.
3. Slightly press the bulb ( 5 ) and turn it
counterclockwise.
4. Install a new bulb in the reverse order of
removal.
Use only the amber bulb.
(3)
(4)
(2)
(1) Turn signal assembly
(2) Screws
(3) Hook
122
http://mototh.com
(4) Turn signal lens
(5) Bulb
10/02/17 17:03:02 32KWN600_133
License Light Bulb
1. Remove the screws ( 1 ).
2. Remove the license light cover ( 2 ).
3. Pull out the bulb ( 3 ) without turning.
4. Install a new bulb in the reverse order of
removal.
(3)
(1)
(2)
(1) Screws
(2) License light cover
(3) Bulb
123
http://mototh.com
10/02/17 17:03:10 32KWN600_134
CLEANING
Clean your scooter regularly to protect the
surface finishes and inspect for damage,
wear, and oil, coolant or brake fluid leakage.
Avoid cleaning products that are not
specif ically designed f or scooter or
automobile surfaces.
They may contain harsh detergents or
chemical solvents that could damage the
metal, paint, and plastic on your scooter.
If your scooter is still warm from recent
operation, give the engine and exhaust
system time to cool off.
We recommend avoiding the use of high
pressure water spray (typical in coinoperated car washes).
High pressure water (or air) can damage
certain parts of the scooter.
Washing the scooter
1. Rinse the scooter thoroughly with cool
water to remove loose dirt.
2. Clean the scooter with a sponge or soft
cloth using cool water.
Avoid directing water to muffler outlets
and electrical parts.
3. Clean the plastic parts using a cloth or
sponge dampened with a solution of mild
detergent and water. Rub the soiled area
gently rinsing it frequently with fresh
water.
Take care to keep brake fluid or chemical
solvents off the scooter.
They will damage the plastic and painted
surfaces.
The inside of the headlight lens may be
clouded immediately after washing the
scooter. Moisture condensation inside the
headlight lens will disappear gradually by
lighting the headlight in high beam. Run the
engine while keeping the headlight on.
124
http://mototh.com
10/02/17 17:03:16 32KWN600_135
4. Af ter cleaning, rinse the scooter
thoroughly with plenty of clean water.
Strong detergent residue can corrode
alloy parts.
5. Dry the scooter, start the engine and let it
run for several minutes.
6. Test the brakes before riding the scooter.
Several applications may be necessary to
restore normal braking performance.
Braking efficiency may be temporarily
impaired immediately after washing the
scooter.
Anticipate longer stopping distance to avoid
a possible accident.
TEST BRAKES
125
http://mototh.com
10/02/17 17:03:22 32KWN600_136
Finishing Touches
After washing your scooter, consider using
a commercially-available spray cleaner/
polish or quality liquid or paste wax to finish
the job. Use only a non-abrasive polish or
wax made specifically for motorcycles or
automobiles. Apply the polish or wax
according to the instructions on the
container.
Removing Road Salt
Road Salt used on roads during winter and
salt from seawater causes rust.
Wash your scooter as follows after it has
run through salty water or on roads treated
with Road Salt.
1. Clean the scooter using cool water (page
124 ).
Do not use warm water.
This worsens the effect of the salt.
2. Dry the scooter and the surface of the
metal is protected with the wax.
126
http://mototh.com
10/02/17 17:03:24 32KWN600_137
Painted Aluminum Wheel Maintenance
Aluminum may corrode from contact with
dirt, mud, or road salt. Clean the wheels
af ter riding through any of these
substances. Use a wet sponge and mild
detergent. Avoid stiff brushes, steel wool, or
cleaners containing abrasives or chemical
compounds.
After washing, rinse with plenty of water
and dry with a clean cloth.
127
http://mototh.com
10/02/17 17:03:30 32KWN600_138
STORAGE GUIDE
Extended storage, such as for winter,
requires that you take certain steps to
reduce the effects of deterioration from
non-use of the scooter. In addition,
necessary repairs should be made BEFORE
storing the scooter; otherwise, these repairs
may be forgotten by the time the scooter is
removed from storage.
STORAGE
1. Change the engine oil.
2. Make sure the cooling system is filled
with a 50/50 % antifreeze solution.
3. Empty the fuel tank into an approved
petrol container using a commercially
available hand siphon or an equivalent
method. Spray the inside of the tank with
an aerosol rust-inhibiting oil.
Reinstall the fuel fill cap on the tank.
128
http://mototh.com
Petrol is highly flammable and
explosive. You can be burned or
seriously injured when handling fuel.
Stop the engine and keep heat,
sparks, and flame away.
Refuel only outdoors.
Wipe up spills immediately.
10/02/17 17:03:36 32KWN600_139
4. To prevent rusting in the cylinder,
perform the following:
Remove the spark plug cap from the
spark plug. Using tape or string, secure
the cap to any convenient plastic body
part so that it is positioned away from
the spark plug.
Remove the spark plug from the
engine and store it in a safe place. Do
not connect the spark plug to the spark
plug cap.
Pour a tablespoon (15−20 cm ) of
clean engine oil into the cylinder and
cover the spark plug hole with a piece
of cloth.
Crank the engine several times to
distribute the oil.
Reinstall the spark plug and spark plug
cap.
5. Remove the battery. Store in an area
protected from freezing temperatures
and direct sunlight.
Slow charge the battery once a month.
6. Wash and dry the scooter. Wax all
painted surfaces. Coat chrome with
rustinhibiting oil.
7. Inflate the tyres to their recommended
pressures. Place the scooter on blocks to
raise both tyres off the ground.
8. Cover the scooter (don’t use plastic or
other coated materials) and store in an
unheated area, free of dampness with a
minimum of daily temperature variation.
Do not store the scooter in direct sunlight.
129
http://mototh.com
10/02/17 17:03:41 32KWN600_140
REMOVAL FROM STORAGE
1. Uncover and clean the scooter.
2. Change the engine oil if more than 4
months have passed since the start of
storage.
3. Charge the battery as required. Install the
battery.
4. Drain any excess aerosol rust-inhibiting
oil from the fuel tank. Fill the fuel tank
with fresh petrol.
5. Perform all Pre-ride Inspection checks
(page 67 ).
Test ride the scooter at low speeds in a
safe riding area away from traffic.
130
http://mototh.com
10/02/17 17:03:45 32KWN600_141
TAKING CARE OF THE UNEXPECTED
IF YOU CRASH
Personal safety is your first priority after a
crash. If you or anyone else has been
injured, take time to assess the severity of
the injuries and whether it is safe to
continue riding. Call f or emergency
assistance if needed. Also follow applicable
laws and regulations if another person or
vehicle is involved in the crash.
If there is minor damage, or you are unsure
about possible damage, ride slowly and
cautiously. Sometimes, crash damage is
hidden or not immediately apparent, so you
should have your scooter thoroughly
checked at a qualified service facility as
soon as possible. Also, be sure to have your
Honda dealer check the f rame and
suspension after any serious crash.
If you decide that you are capable of riding
safely, first evaluate the condition of your
scooter. If the engine is still running, turn it
off and look it over carefully; inspect it for
fluid leaks, check the tightness of critical
nuts and bolts, and secure such parts as the
handlebar, control levers, brakes, and
wheels.
131
http://mototh.com
http://mototh.com
58 X 57.9 mm
10.6:1
153 cm3
http://mototh.com
10/02/17 17:04:05 32KWN600_144
CHASSIS AND SUSPENSION
Caster
Trail
Tyre size, front
Tyre size, rear
Tyre type
POWER TRANSMISSION
Primary reduction
Final reduction
27°00’
86 mm (3.4 in)
90/90-14M/C 46P
IRC
SS-560F
100/90-14M/C 57P
IRC
SS-560R
bias-ply, tubeless
V−Belt
11.271
134
http://mototh.com
10/02/17 17:04:13 32KWN600_145
ELECTRICAL
Battery
Generator
LIGHTS
Headlight
Brake/Tail light
Turn signal light
Position light
License light
FUSE
Main fuse 1
Main fuse 2
Sub fuse
12V−6Ah (10HR) / 6.3Ah (20HR)
0.308 kW / 5,000 min (rpm)
Front
Rear
12V−35/30W × 2
12V−21/5W
12V−21W × 2
12V−21W × 2
12V−5W × 2
12V−5W
10A
30A
10A, 15A
135
http://mototh.com
10/02/17 17:04:19 32KWN600_146
CATALYTIC CONVERTER
This scooter is equipped with a catalytic
converter.
The catalytic converter contains precious
metals that serve as catalysts, promoting
chemical reactions to convert the exhaust
gasses without affecting the metals.
The catalytic converter acts on HC, CO, and
NOx. A replacement unit must be an
original Honda part or its equivalent.
A defective catalytic converter contributes
to air pollution, and can impair your engine’s
performance. Follow these guidelines to
protect your scooter’s catalytic converter.
The catalytic converter must operate at a
high temperature for the chemical reactions
to take place. It can set on fire any
combustible materials that come near it.
Park your scooter away from high grasses,
dry leaves, or other flammables.
Keep the engine in good running
condition.
A poorly running engine can cause the
catalytic converter to overheat causing
damage to the converter or the scooter.
Always use unleaded petrol. Even a small
amount of leaded petrol can contaminate
the catalyst metals, making the catalytic
converter ineffective.
If your engine is misfiring, backfiring,
stalling, or otherwise not running
properly, stop riding and turn off the
engine. Have your scooter serviced as
soon as possible.
136
http://mototh.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement