Owner`s Manual

Owner`s Manual
Owner’s Manual
Thank you, and congratulations on your choice of the Roland Powered Subwoofer KCW-1.
These sections provide important information concerning the proper operation of the unit.
Additionally, in order to feel assured that you have gained a good grasp of every feature
provided by your new unit, Owner’s manual should be read in its entirety. The manual
should be saved and kept on hand as a convenient reference.
Before using this unit, carefully read the sections entitled:
• IMPORTANT SAFETY INSTRUCTIONS (p. 2)
• USING THE UNIT SAFELY (p. 3–p. 4)
• IMPORTANT NOTES (p. 5)
Main Features
• Equipped with a specialized 10-inch (25 cm) subwoofer speaker, the high-powered KCW1 has an output of 200 watts.
• The KCW-1’s CROSSOVER knob allows you to balance sounds according to the lowfrequency playback capability of the connected device.
• Also featured is a BOTTOM switch that further boosts low-frequency sounds.
• INPUT and THRU OUT both feature 1/4” phone jacks and XLR connectors for greater
connectivity to a variety of devices.
• With the THRU OUT connector, you can even connect devices with no SUBWOOFER
OUT to the KCW-1.
• You can connect an optional foot switch and use your foot to switch the output from the
KCW-1’s speaker on and off.
• The unit also has a built-in handle for easy portability.
Copyright © 2003 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form without the
written permission of ROLAND CORPORATION.
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATTENTION: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the product.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS.
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
WARNING - When using electric products, basic precautions should always be followed, including the following:
1.
2.
3.
4.
5.
6.
7.
8.
9.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with a dry cloth.
Do not block any of the ventilation openings. Install in
accordance with the manufacturers instructions.
Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. When the provided
plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12. Never use with a cart, stand, tripod, bracket,
or table except as specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
For the U.K.
WARNING:
THIS APPARATUS MUST BE EARTHED
IMPORTANT: THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE.
GREEN-AND-YELLOW: EARTH, BLUE: NEUTRAL, BROWN: LIVE
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the
letter E or by the safety earth symbol or coloured GREEN or GREEN-AND-YELLOW.
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.
For EU Countries
This product complies with the requirements of European Directives EMC 89/336/EEC and LVD 73/23/EEC.
2
USING THE UNIT SAFELY
The
symbol alerts the user to important instructions
or warnings.The specific meaning of the symbol is
determined by the design contained within the
triangle. In the case of the symbol at left, it is used for
general cautions, warnings, or alerts to danger.
Used for instructions intended to alert
the user to the risk of death or severe
injury should the unit be used
improperly.
Used for instructions intended to alert
the user to the risk of injury or material
damage should the unit be used
improperly.
* Material damage refers
other adverse effects
respect to the home
furnishings, as well
animals or pets.
The
symbol alerts the user to items that must never
be carried out (are forbidden). The specific thing that
must not be done is indicated by the design contained
within the circle. In the case of the symbol at left, it
means that the unit must never be disassembled.
to damage or
caused with
and all its
to domestic
The ● symbol alerts the user to things that must be
carried out. The specific thing that must be done is
indicated by the design contained within the circle. In
the case of the symbol at left, it means that the powercord plug must be unplugged from the outlet.
001
007
• Before using this unit, make sure to read the
instructions below, and the Owner’s Manual.
• Make sure you always have the unit placed so it is
level and sure to remain stable. Never place it on
stands that could wobble, or on inclined surfaces.
..........................................................................................................
..........................................................................................................
002a
• Do not open or perform any internal modifications on the unit.
..........................................................................................................
003
• Do not attempt to repair the unit, or replace parts
within it (except when this manual provides
specific instructions directing you to do so). Refer
all servicing to your retailer, the nearest Roland
Service Center, or an authorized Roland
distributor, as listed on the “Information” page.
..........................................................................................................
004
• Never use or store the unit in places that are:
• Subject to temperature extremes (e.g., direct
sunlight in an enclosed vehicle, near a heating
duct, on top of heat-generating equipment); or
are
• Damp (e.g., baths, washrooms, on wet floors);
or are
• Humid; or are
• Exposed to rain; or are
• Dusty; or are
• Subject to high levels of vibration.
..........................................................................................................
008a
• The unit should be connected to a power supply
only of the type described in the operating instructions, or as marked on the unit.
..........................................................................................................
008e
• Use only the attached power-supply cord.
..........................................................................................................
009
• Do not excessively twist or bend the power cord,
nor place heavy objects on it. Doing so can
damage the cord, producing severed elements and
short circuits. Damaged cords are fire and shock
hazards!
..........................................................................................................
010
• This unit, either alone or in combination with an
amplifier and headphones or speakers, may be
capable of producing sound levels that could
cause permanent hearing loss. Do not operate for
a long period of time at a high volume level, or at
a level that is uncomfortable. If you experience
any hearing loss or ringing in the ears, you should
immediately stop using the unit, and consult an
audiologist.
..........................................................................................................
011
• Do not allow any objects (e.g., flammable material,
coins, pins); or liquids of any kind (water, soft
drinks, etc.) to penetrate the unit.
..........................................................................................................
3
012a:
101a
• Immediately turn the power off, remove the
power cord from the outlet, and request servicing
by your retailer, the nearest Roland Service
Center, or an authorized Roland distributor, as
listed on the “Information” page when:
• The unit should be located so that its location or
position does not interfere with its proper ventilation.
..........................................................................................................
• The power-supply cord, or the plug has been
damaged; or
• If smoke or unusual odor occurs
• Objects have fallen into, or liquid has been
spilled onto the unit; or
• The unit has been exposed to rain (or otherwise
has become wet); or
• The unit does not appear to operate normally or
exhibits a marked change in performance.
..........................................................................................................
013
• In households with small children, an adult
should provide supervision until the child is
capable of following all the rules essential for the
safe operation of the unit.
..........................................................................................................
014
• Protect the unit from strong impact.
(Do not drop it!)
..........................................................................................................
015
• Do not force the unit’s power-supply cord to share
an outlet with an unreasonable number of other
devices. Be especially careful when using
extension cords—the total power used by all
devices you have connected to the extension
cord’s outlet must never exceed the power rating
(watts/amperes) for the extension cord. Excessive
loads can cause the insulation on the cord to heat
up and eventually melt through.
..........................................................................................................
016
• Before using the unit in a foreign country, consult
with your retailer, the nearest Roland Service
Center, or an authorized Roland distributor, as
listed on the “Information” page.
..........................................................................................................
026
• To reduce the risk of fire or electric shock, do not
expose this apparatus to rain or moisture and
objects filled with liquids, such as vases, should
not be placed on this apparatus.
..........................................................................................................
add
• This device is designed to be set on the floor.
When using this device, be sure to set it on a stable
surface, with the unit’s port side facing forward.
When setting up the unit, always make sure that
there is ample clearance between the unit and
walls and other obstructions to maintain easy
access to the controls.
..........................................................................................................
4
102b
• Always grasp only the plug on the power-supply
cord when plugging into, or unplugging from, an
outlet or this unit.
..........................................................................................................
103a:
• Any accumulation of dust between the power
plug and the power outlet can result in poor
insulation and lead to fire. Periodically wipe away
such dust with a dry cloth. Also, disconnect the
power plug from the power outlet whenever the
unit is to remain unused for an extended period of
time.
..........................................................................................................
104
• Try to prevent cords and cables from becoming
entangled. Also, all cords and cables should be
placed so they are out of the reach of children.
..........................................................................................................
106
• Never climb on top of, nor place heavy objects on
the unit.
..........................................................................................................
107b
• Never handle the power cord or its plugs with wet
hands when plugging into, or unplugging from,
an outlet or this unit.
..........................................................................................................
108a
• Before moving the unit, disconnect the power
plug from the outlet, and pull out all cords from
external devices.
..........................................................................................................
109a
• Before cleaning the unit, turn off the power and
unplug the power cord from the outlet.
..........................................................................................................
110a
• Whenever you suspect the possibility of lightning
in your area, pull the plug on the power cord out
of the outlet.
..........................................................................................................
IMPORTANT NOTES
291b
In addition to the items listed under “IMPORTANT SAFETY INSTRUCTIONS” and “USING THE UNIT SAFELY” on pages 2,
3 and 4, please read and observe the following:
Power Supply
Maintenance
301
401a
• Do not use this unit on the same power circuit with any device
that will generate line noise (such as an electric motor or variable
lighting system).
• For everyday cleaning wipe the unit with a soft, dry cloth or one that
has been slightly dampened with water. To remove stubborn dirt,
use a cloth impregnated with a mild, non-abrasive detergent. Afterwards, be sure to wipe the unit thoroughly with a soft, dry cloth.
307
• Before connecting this unit to other devices, turn off the power to
all units. This will help prevent malfunctions and/or damage to
speakers or other devices.
402
• Never use benzine, thinners, alcohol or solvents of any kind, to
avoid the possibility of discoloration and/or deformation.
308
• Although the LEDs are switched off when the POWER switch is
switched off, this does not mean that the unit has been
completely disconnected from the source of power. If you need to
turn off the power completely, first turn off the POWER switch,
then unplug the power cord from the power outlet. For this
reason, the outlet into which you choose to connect the power
cord’s plug should be one that is within easy reach.
Placement
351
• Using the unit near power amplifiers (or other equipment
containing large power transformers) may induce hum. To
alleviate the problem, change the orientation of this unit; or move
it farther away from the source of interference.
352a
• This device may interfere with radio and television reception. Do
not use this device in the vicinity of such receivers.
352b
• Noise may be produced if wireless communications devices, such
as cell phones, are operated in the vicinity of this unit. Such noise
could occur when receiving or initiating a call, or while
conversing. Should you experience such problems, you should
relocate such wireless devices so they are at a greater distance
from this unit, or switch them off.
354b
• Do not expose the unit to direct sunlight, place it near devices
that radiate heat, leave it inside an enclosed vehicle, or otherwise
subject it to temperature extremes. Also, do not allow lighting
devices that normally are used while their light source is very
close to the unit (such as a piano light), or powerful spotlights to
shine upon the same area of the unit for extended periods of time.
Excessive heat can deform or discolor the unit.
355b
• When moved from one location to another where the temperature and/or humidity is very different, water droplets (condensation) may form inside the unit. Damage or malfunction may
result if you attempt to use the unit in this condition. Therefore,
before using the unit, you must allow it to stand for several
hours, until the condensation has completely evaporated.
• For routine care of the carpeted surfaces, use a brush with stiff bristles.
Additional Precautions
553
• Use a reasonable amount of care when using the unit’s buttons,
sliders, or other controls; and when using its jacks and
connectors. Rough handling can lead to malfunctions.
556
• When connecting / disconnecting all cables, grasp the connector
itself—never pull on the cable. This way you will avoid causing
shorts, or damage to the cable’s internal elements.
557
• A small amount of heat will radiate from the unit during normal
operation.
558b
• To avoid disturbing your neighbors, try to keep the unit’s volume
at reasonable levels (especially when it is late at night).
559a
• When you need to transport the unit, package it in the box
(including padding) that it came in, if possible. Otherwise, you
will need to use equivalent packaging materials.
562
• Use a cable from Roland to make the connection. If using some other
make of connection cable, please note the following precautions.
• Some connection cables contain resistors. Do not use cables
that incorporate resistors for connecting to this unit. The use
of such cables can cause the sound level to be extremely low,
or impossible to hear. For information on cable specifications,
contact the manufacturer of the cable.
add
• Do not place your hands inside the ports on the front of the
KCW-1. Your hands may become lodged in the ports, possibly
resulting in injury to your hand and damaging the unit.
Particularly when using the unit in the presence of small children,
always make sure that an adult is present to provide supervision
and prevent children from inserting their hands or feet in the
ports.
356
• Do not allow rubber, vinyl, or similar materials to remain on the
unit for long periods of time. Such objects can discolor or
otherwise harmfully affect the finish.
357
• Do not put anything that contains water (e.g., flower vases) on
the unit. Also, avoid the use of insecticides, perfumes, alcohol,
nail polish, spray cans, etc., near the unit. Swiftly wipe away any
liquid that spills on the unit using a dry, soft cloth.
359
• Do not paste stickers, decals, or the like to this instrument. Peeling
such matter off the instrument may damage the exterior finish.
• Do not allow objects to remain on top of the unit while it is in
operation.
5
Panel Descriptions
■
Control Section
3.
fig.20
5
4
3
2
BOTTOM switch
Setting this switch to ON allows you to play the low end
with even greater power and punch.
1
Use this switch according to the input source as well as the
performance environment.
The BOTTOM switch is useful in the following situations.
• When you want to produce special low-frequency sounds
in a range beyond what ordinary subwoofers can handle.
• To get the low bass effect at low volume levels.
6
• When the connected device features sufficient lowfrequency playback, but the proper volume balance with
the KCW-1 cannot be attained with the CROSSOVER and
VOLUME knob.
7
* The BOTTOM switch affects only the speaker output.
4. PHASE switch
Setting this switch to INV inverts the phase of sounds played
from the KCW-1’s speaker.
8
Ordinarily use the KCW-1 with this switch set to NOR.
Switch the setting as needed according to conditions where
the unit is being set up to achieve greater volume in the bass
range.
The PHASE switch is useful in the following type of situation.
9
1.
10
11
VOLUME knob
This adjusts the total volume level of the unit’s internal speaker.
2.
* The PHASE switch affects only the speaker output.
CROSSOVER knob
This adjusts the frequency range played back from the unit’s
speaker. Adjust this according to the low-frequency playback
capabilities of the connected device, as well as the
performance environment.
The relationship between the CROSSOVER knob indicator
and the active frequency range is shown below.
5.
FOOT SW jack
You can connect a momentary-type foot switch (the optional
DP-2 or BOSS FS-5U) and use the switch to turn the output of
the KCW-1’s speaker on and off.
* Switching with the foot switch affects only the speaker output.
OUTPUT LEVEL
INPUT Section
6.
30
CROSSOVER Variable range
When connected to
large-diameter speakers
6
• The KCW-1’s low-frequency sound may not be fully
apparent when the placement relation or room acoustics
cause phase discrepancies between the KCW-1 and the
connected device.
Switching the PHASE switch in such conditions can allow
you to achieve greater volume in the bass range.
120
Frequency (Hz)
When connected to
small-diameter speakers
INPUT jacks
Signals from devices equipped with a SUBWOOFER OUT
connector are input here. For instructions on connecting to
devices not equipped with any SUBWOOFER OUT, refer to
“Instructions for Connecting to Devices With No
SUBWOOFER OUT” (p. 9).
Two types of connectors are provided: XLR connectors and
1/4” phone jacks. Use the type of connector matching the
device you are connecting.
These accept level input of +4 dBu.
Panel Descriptions
THRU OUT Section
7.
■
Front Panel
THRU OUT jacks
Signals input to the INPUT jacks are output here unchanged.
These are convenient when connecting to devices that have
no SUBWOOFER OUT. For detailed connection instructions,
refer to “Instructions for Connecting to Devices With No
SUBWOOFER OUT” (p. 9).
12
Two types of connectors are provided: XLR connectors and
1/4” phone jacks. Use the type of connectors that match the
device you are connecting.
These output jacks provide +4 dBu line level output.
* No sounds are output from the THRU OUT jacks when the
power is turned off.
* The PHASE switch, BOTTOM switch, and CROSSOVER
12. OPERATION indicator
This lights up when the power is on. When a connected foot
switch is used to switch off the KCW-1’s speaker output, the
indicator flashes.
knob do not affect the output from THRU OUT.
* When inputting only to the INPUT L (MONO) jack, the signal
is output from both the L and R jacks of THRU OUT.
8.
GND LIFT switch
Allows you to make/break the connection between the GND
pins of the THRU OUT XLR connectors and the KCW-1’s
ground.
If you encounter noise problems that are possibly caused by
a ground loop, try changing the switch position to alleviate
the problem.
9.
POWER switch
This switches the power on and off.
* Before turning the power on or off, be sure to put the VOLUME
knob at 0.
* This unit is equipped with a protection circuit. A brief interval
(a few seconds) after power up is required before the unit will
operate normally.
* Refer to p. 10 for the order in which to turn the power to
connected devices on and off.
10. POWER indicator
This lights up when the power is on.
11. AC inlet
Connect the included Power cord here. Plug it firmly in, so
that the cable does not accidentally become disconnected.
7
Connect your KCW-1
Instructions for Connecting to Devices Equipped with
SUBWOOFER OUT Connectors (Mono Connection)
When connecting to devices equipped with SUBWOOFER OUT connectors, make the connections between
the KCW-1 and other devices after referring to the following figure.
fig.
or
SUBWOOFER OUT
Polarity Switch
DP-2
FS-5U
Foot Switch
(Momentary type)
Device equipped
with SUBWOOFER OUT
Use a 1/4” phone audio cable to connect the SUBWOOFER OUT on the device featuring the SUBWOOFER
OUT connector to the KCW-1’s INPUT L (MONO).
Instructions for Connecting to Devices Equipped with
SUBWOOFER OUT Connectors (Stereo Connection)
When connecting the KCW-1 to the KC-550/350 or similar devices, and using a stereo link to play sounds in
stereo, make the connections to the KCW-1 as shown in the following figure.
fig.
or
SUBWOOFER
OUT
SUBWOOFER
OUT
DP-2
Polarity Switch
FS-5U
Foot Switch
(Momentary type)
R ch (Master)
L ch (Sub)
Use 1/4” phone audio cables to connect both the R (Master) and L (Sub) SUBWOOFER OUTs on the KC550/350 or other devices to the KCW-1’s INPUT L and R.
8
Connect your KCW-1
Instructions for Connecting to Devices With No SUBWOOFER OUT
When connecting to devices with no SUBWOOFER OUT connectors, connect such equipment to the KCW-1
after referring to the following figure.
fig.
or
or
MONITOR OUT
MONITOR
OUT
INPUT
Mixer
DP-2
Polarity Switch
FS-5U
Foot Switch
(Momentary Type)
VS Series
R ch
L ch
Powered Monitor
Input signals from the VS Series and other output devices to the INPUT connectors. Connect DS Series
powered monitors or similar devices to the KCW-1’s THRU OUT.
The INPUT section features XLR connectors and 1/4” phone jacks. Although both types may be used
simultaneously, adjust the connected devices to attain the proper volume balance between the input devices.
THRU OUT also includes XLR connectors and 1/4” phone jacks. Both types may be used simultaneously.
Notes Regarding the Connections
* To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the
power on all devices before making any connections. Set the KCW-1’s VOLUME knob to zero.
* When connection cables with resistors are used, the volume level of equipment connected to the inputs may be low.
If this happens, use connection cables that do not contain resistors, such as those from the Roland PCS series.
* The pin assignment for the XLR type connectors is as shown below. Before making any connections, make sure that
this pin assignment is compatible with that of all your other devices.
fig.31
9
Connect your KCW-1
Switching the Power On and
Off
Once the connections have been completed, turn on power to
your various devices in the order specified. By turning on
devices in the wrong order, you risk causing malfunction
and/or damage to speakers and other devices.
1. Make sure that all volume controls on the KCW-1 and
connected devices are set to 0.
2. Turn on all the devices connected to the KCW-1’s input
jacks.
3. Turn on the KCW-1.
4. Switch on any equipment connected to the KCW-1’s
THRU OUT jacks.
5. Adjust the volume levels for the devices.
6. Before switching off the power, lower the volume on
each of the devices in your system and then TURN OFF
the devices in the reverse order to which they were
switched on.
* This unit is equipped with a protection circuit. A brief interval
(a few seconds) after power up is required before the unit will
operate normally. For protection from sudden big sound, always
make sure to have the volume level turned down before
switching on power.
* Even with the volume all the way down, you may still hear some
sound when the power is switched on, but this is normal, and
does not indicate a malfunction.
10
Block Diagram
fig.50
INPUT L
XLR
THRU OUT L
XLR
INPUT R
XLR
THRU OUT R
XLR
INPUT L
(MONO)
THRU OUT L
INPUT R
THRU OUT R
CROSSOVER
PHASE
BOTTOM
PHASE
BOTTOM
SPEAKER
MUTE
POWER AMP
VOLUME
CROSSOVER
FOOT SW
Main Specifications
KCW-1: Powered Subwoofer
Rated Power Output
200 W
Nominal Input Level (100 Hz)
Input: +4 dBu (XLR type, 1/4” phone type)
Nominal Output Level (100 Hz)
Thru Out: +4 dBu (XLR type, 1/4” phone type)
* 0 dBu = 0.775 Vrms
Speaker
25 cm (10 inches) x 1
Controls
VOLUME Knob
CROSSOVER Knob
BOTTOM Switch
PHASE Switch
POWER Switch
GND LIFT Switch
Indicator
POWER
OPERATION
Connectors
INPUT Connector L, R (XLR type)
INPUT Jack L (MONO), R (1/4” phone type)
THRU OUT Connector L, R (XLR type)
THRU OUT Jack L, R (1/4” phone type)
FOOT SW Jack (1/4” phone type)
Power Supply
AC 117 V, AC 230 V, AC 240 V: 50/60 Hz
AC 220 V: 60 Hz
Power Consumption
135 W
Dimensions
438 (W) x 440 (D) x 460 (H) mm
17-1/4 (W) x 17-3/8 (D) x 18-1/8 (H) inches
Weight
23.0 kg
50 lbs 12 oz
Accessory
Owner’s Manual
Power Cord
Options
Pedal Switch: DP-2
Foot Switch: FS-5U (BOSS)
* In the interest of product improvement, the specifications and/or
appearance of this unit are subject to change without prior notice.
11
Information
When you need repair service, call your nearest Roland Service Center or authorized Roland distributor in your country as
shown below.
AFRICA
EGYPT
Al Fanny Trading Office
9, EBN Hagar A1 Askalany Street,
ARD E1 Golf, Heliopolis,
Cairo 11341, EGYPT
TEL: 20-2-417-1828
REUNION
Maison FO - YAM Marcel
25 Rue Jules Hermann,
Chaudron - BP79 97 491
Ste Clotilde Cedex,
REUNION ISLAND
TEL: (0262) 218-429
SOUTH AFRICA
That Other Music Shop
(PTY) Ltd.
11 Melle St., Braamfontein,
Johannesbourg, SOUTH AFRICA
P.O.Box 32918, Braamfontein 2017
Johannesbourg, SOUTH AFRICA
TEL: (011) 403 4105
Paul Bothner (PTY) Ltd.
MALAYSIA
EL SALVADOR
IRELAND
BENTLEY MUSIC SDN BHD
OMNI MUSIC
Roland Ireland
140 & 142, Jalan Bukit Bintang
55100 Kuala Lumpur,MALAYSIA
TEL: (03) 2144-3333
75 Avenida Norte y Final
Alameda Juan Pablo ,
Edificio No.4010 San Salvador,
EL SALVADOR
TEL: 262-0788
G2 Calmount Park, Calmount
Avenue, Dublin 12
Republic of IRELAND
TEL: (01) 4294444
MEXICO
ITALY
Casa Veerkamp, s.a. de c.v.
Roland Italy S. p. A.
Av. Toluca No. 323, Col. Olivar
de los Padres 01780 Mexico D.F.
MEXICO
TEL: (55) 5668-6699
Viale delle Industrie 8,
20020 Arese, Milano, ITALY
TEL: (02) 937-78300
PHILIPPINES
G.A. Yupangco & Co. Inc.
339 Gil J. Puyat Avenue
Makati, Metro Manila 1200,
PHILIPPINES
TEL: (02) 899 9801
SINGAPORE
Swee Lee Company
150 Sims Drive,
SINGAPORE 387381
TEL: 6846-3676
CRISTOFORI MUSIC PTE
LTD
Blk 3014, Bedok Industrial Park E,
#02-2148, SINGAPORE 489980
TEL: 6243-9555
TAIWAN
ROLAND TAIWAN
ENTERPRISE CO., LTD.
17 Werdmuller Centre,
Main Road, Claremont 7708
SOUTH AFRICA
Room 5, 9fl. No. 112 Chung Shan
N.Road Sec.2, Taipei, TAIWAN,
R.O.C.
TEL: (02) 2561 3339
P.O.BOX 23032, Claremont 7735,
SOUTH AFRICA
TEL: (021) 674 4030
THAILAND
Theera Music Co. , Ltd.
ASIA
330 Verng NakornKasem, Soi 2,
Bangkok 10100, THAILAND
TEL: (02) 2248821
CHINA
VIETNAM
Roland Shanghai Electronics
Co.,Ltd.
5F. No.1500 Pingliang Road
Shanghai 200090, CHINA
TEL: (021) 5580-0800
Roland Shanghai Electronics
Co.,Ltd.
(BEIJING OFFICE)
10F. No.18 Anhuaxili
Chaoyang District, Beijing 100011
CHINA
TEL: (010) 6426-5050
Roland Shanghai Electronics
Co.,Ltd.
(GUANGZHOU OFFICE)
2/F., No.30 Si You Nan Er Jie Yi
Xiang, Wu Yang Xin Cheng,
Guangzhou 510600, CHINA
Tel: (020) 8736-0428
HONG KONG
Tom Lee Music Co., Ltd.
Service Division
22-32 Pun Shan Street, Tsuen
Wan, New Territories,
HONG KONG
TEL: 2415 0911
Saigon Music
Suite DP-8
40 Ba Huyen Thanh Quan Street
Hochiminh City, VIETNAM
Tel: (08) 930-1969
AUSTRALIA/
NEW ZEALAND
AUSTRALIA
Roland Corporation
Australia Pty., Ltd.
38 Campbell Avenue
Dee Why West. NSW 2099
AUSTRALIA
TEL: (02) 9982 8266
NEW ZEALAND
Roland Corporation Ltd.
32 Shaddock Street, Mount Eden,
Auckland, NEW ZEALAND
TEL: (09) 3098 715
CENTRAL/LATIN
AMERICA
ARGENTINA
8th Floor, Railway Plaza, 39
Chatham Road South, T.S.T,
Kowloon, HONG KONG
TEL: 2333 1863
Instrumentos Musicales S.A.
INDIA
BRAZIL
409, Nirman Kendra Mahalaxmi
Flats Compound Off. Dr. Edwin
Moses Road, Mumbai-400011,
INDIA
TEL: (022) 2493 9051
INDONESIA
PT Citra IntiRama
J1. Cideng Timur No. 15J-150
Jakarta Pusat
INDONESIA
TEL: (021) 6324170
KOREA
Cosmos Corporation
1461-9, Seocho-Dong,
Seocho Ku, Seoul, KOREA
TEL: (02) 3486-8855
SUPRO MUNDIAL, S.A.
Boulevard Andrews, Albrook,
Panama City, REP. DE PANAMA
TEL: 315-0101
PARAGUAY
Distribuidora De
Instrumentos Musicales
J.E. Olear y ESQ. Manduvira
Asuncion PARAGUAY
TEL: (021) 492-124
URUGUAY
Av.Santa Fe 2055
(1123) Buenos Aires
ARGENTINA
TEL: (011) 4508-2700
Roland Brasil Ltda
Rua San Jose, 780 Sala B
Parque Industrial San Jose
Cotia - Sao Paulo - SP, BRAZIL
TEL: (011) 4615 5666
COSTA RICA
JUAN Bansbach
Instrumentos Musicales
Ave.1. Calle 11, Apartado 10237,
San Jose, COSTA RICA
TEL: 258-0211
CHILE
Comercial Fancy S.A.
Rut.: 96.919.420-1
Nataniel Cox #739, 4th Floor
Santiago - Centro, CHILE
TEL: (02) 688-9540
NORWAY
Roland Scandinavia Avd.
Kontor Norge
MOCO, INC.
No.41 Nike St., Dr.Shariyati Ave.,
Roberoye Cerahe Mirdamad
Tehran, IRAN
TEL: (021) 285-4169
ISRAEL
Halilit P. Greenspoon &
Sons Ltd.
8 Retzif Ha'aliya Hashnya St.
Tel-Aviv-Yafo ISRAEL
TEL: (03) 6823666
JORDAN
AMMAN Trading Agency
Lilleakerveien 2 Postboks 95
Lilleaker N-0216 Oslo
NORWAY
TEL: 2273 0074
245 Prince Mohammad St.,
Amman 1118, JORDAN
TEL: (06) 464-1200
POLAND
Easa Husain Al Yousifi Est.
P. P. H. Brzostowicz
UL. Gibraltarska 4.
PL-03664 Warszawa POLAND
TEL: (022) 679 44 19
PORTUGAL
KUWAIT
Abdullah Salem Street,
Safat, KUWAIT
TEL: 243-6399
LEBANON
Chahine S.A.L.
Gerge Zeidan St., Chahine Bldg.,
Achrafieh, P.O.Box: 16-5857
Beirut, LEBANON
TEL: (01) 20-1441
Todo Musica S.A.
Tecnologias Musica e Audio,
Roland Portugal, S.A.
Francisco Acuna de Figueroa 1771
C.P.: 11.800
Montevideo, URUGUAY
TEL: (02) 924-2335
Cais Das Pedras, 8/9-1 Dto
4050-465 PORTO
PORTUGAL
TEL: (022) 608 00 60
VENEZUELA
ROMANIA
Musicland Digital C.A.
FBS LINES
Av. Francisco de Miranda,
Centro Parque de Cristal, Nivel
C2 Local 20 Caracas
VENEZUELA
TEL: (212) 285-8586
Piata Libertatii 1,
RO-4200 Gheorghehi
TEL: (095) 169-5043
SAUDI ARABIA
RUSSIA
aDawliah Universal
Electronics APL
MuTek
EUROPE
AUSTRIA
Parsons Music Ltd.
Rivera Digitec (India) Pvt. Ltd.
PANAMA
IRAN
Roland Austria GES.M.B.H.
Siemensstrasse 4, P.O. Box 74,
A-6063 RUM, AUSTRIA
TEL: (0512) 26 44 260
BELGIUM/HOLLAND/
LUXEMBOURG
Roland Benelux N. V.
Houtstraat 3, B-2260, Oevel
(Westerlo) BELGIUM
TEL: (014) 575811
DENMARK
3-Bogatyrskaya Str. 1.k.l
107 564 Moscow, RUSSIA
TEL: (095) 169 5043
SPAIN
Roland Electronics
de España, S. A.
Calle Bolivia 239, 08020
Barcelona, SPAIN
TEL: (93) 308 1000
SWEDEN
Roland Scandinavia A/S
SWEDISH SALES OFFICE
Danvik Center 28, 2 tr.
S-131 30 Nacka SWEDEN
TEL: (0)8 702 00 20
Roland Scandinavia A/S
SWITZERLAND
Nordhavnsvej 7, Postbox 880,
DK-2100 Copenhagen
DENMARK
TEL: 3916 6200
Roland (Switzerland) AG
FRANCE
Roland France SA
4, Rue Paul Henri SPAAK,
Parc de l'Esplanade, F 77 462 St.
Thibault, Lagny Cedex FRANCE
TEL: 01 600 73 500
FINLAND
QATAR
Al Emadi Co. (Badie Studio
& Stores)
P.O. Box 62, Doha, QATAR
TEL: 4423-554
Corniche Road, Aldossary Bldg.,
1st Floor, Alkhobar,
SAUDI ARABIA
P.O.Box 2154, Alkhobar 31952
SAUDI ARABIA
TEL: (03) 898 2081
SYRIA
Technical Light & Sound
Center
Khaled Ebn Al Walid St.
Bldg. No. 47, P.O.BOX 13520,
Damascus, SYRIA
TEL: (011) 223-5384
TURKEY
Barkat muzik aletleri ithalat
ve ihracat Ltd Sti
Siraselviler Caddesi Siraselviler
Pasaji No:74/20
Taksim - Istanbul, TURKEY
TEL: (0212) 2499324
Landstrasse 5, Postfach,
CH-4452 Itingen,
SWITZERLAND
TEL: (061) 927-8383
U.A.E.
UKRAINE
Zak Electronics & Musical
Instruments Co. L.L.C.
TIC-TAC
Mira Str. 19/108
P.O. Box 180
295400 Munkachevo, UKRAINE
TEL: (03131) 414-40
Zabeel Road, Al Sherooq Bldg.,
No. 14, Grand Floor, Dubai, U.A.E.
TEL: (04) 3360715
NORTH AMERICA
Roland Scandinavia As,
Filial Finland
UNITED KINGDOM
Elannontie 5
FIN-01510 Vantaa, FINLAND
TEL: (0)9 68 24 020
Atlantic Close, Swansea
Enterprise Park, SWANSEA
SA7 9FJ,
UNITED KINGDOM
TEL: (01792) 702701
CANADA
MIDDLE EAST
Roland Canada Music Ltd.
(Toronto Office)
BAHRAIN
170 Admiral Boulevard
Mississauga On L5T 2N6
CANADA
TEL: (905) 362 9707
GERMANY
Roland (U.K.) Ltd.
Roland Elektronische
Musikinstrumente HmbH.
Oststrasse 96, 22844 Norderstedt,
GERMANY
TEL: (040) 52 60090
GREECE
STOLLAS S.A.
Music Sound Light
155, New National Road
Patras 26442, GREECE
TEL: 2610 435400
HUNGARY
Roland East Europe Ltd.
Warehouse Area ‘DEPO’ Pf.83
H-2046 Torokbalint, HUNGARY
TEL: (23) 511011
Moon Stores
No.16, Bab Al Bahrain Avenue,
P.O.Box 247, Manama 304,
State of BAHRAIN
TEL: 211 005
CYPRUS
Radex Sound Equipment Ltd.
17, Diagorou Street, Nicosia,
CYPRUS
TEL: (022) 66-9426
Roland Canada Music Ltd.
(Head Office)
5480 Parkwood Way Richmond
B. C., V6V 2M4 CANADA
TEL: (604) 270 6626
U. S. A.
Roland Corporation U.S.
5100 S. Eastern Avenue
Los Angeles, CA 90040-2938,
U. S. A.
TEL: (323) 890 3700
As of July 1, 2003 (Roland)
SD000225
2DH
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement