Electric Log Splitter with Foot Pedal
model number 060-3770-4 | contact us: 1.866.523.5218
IMPORTANT:
Read and follow all safety rules and operating instructions before using this product.
Instruction
Manual
2 model number 060-3770-4 | contact us: 1.866.523.5218
Specifications
Know Your Log Splitter
Exploded View
Parts List
Operation
Maintenance
Troubleshooting
Safety Warnings, Instructions, and Symbols
Warranty
ELECTRIC LOG SPLITTER
Model Number
Motor
Log Capacity (Diameter)
Log Capacity (Length)
Splitting Force
Hydraulic Pressure
Hydraulic Oil Capacity
Overall Size
Weight
Length
Width
Height
060-3770-4
120 V 60 Hz 15 A 1 3/4 HP
2 – 10” (5 – 25 cm)
2 – 20” (5 – 25 cm) with duo-cut
20 1/2” (52 cm)
17 11/32” (45 cm) with duo-cut
5 tons
20 MPa
3.2 L
37” (94 cm)
10 1/2” (27 cm)
20” (51 cm)
101 lb (46 kg)
The diameter of the log is only a guideline—a small log can be difficult to split if it has knots or very tough fibers.
9
13
14
15
18
6
7
2
3
model number 060-3770-4 | contact us: 1.866.523.5218
Bolt the support leg to the log splitter, place it on a stable and flat ground.
1.
Log pusher
2.
Work table
3.
Wedge
4.
Support leg
5.
Log retaining plates
6.
Motor
7.
Switch
8.
Pushbutton box
9.
Wheels (for minor moving ONLY)
10. Control lever guard
11. Bleed screw
12. Oil drain bolt with dipstick
13. Maximum pressure limiting screw
14. Alternate log pusher with duo-cut wedge
15. Foot pedal
10
9
8
7
1
6 5
2 3
14
15
4
13
11
12
13
3
4 model number 060-3770-4 | contact us: 1.866.523.5218
Replace original log pusher with the duo-cut blade. This enables your machine to have twice the effective splitting capacity of similarly rated electric log splitters and ensures that if a knot is encountered at one end, it will still split from the other.
The duo-cut blade can be easily bolted on in place of the standard log pusher.
KNOW YOUR LOG SPLITTER
The safe use of this product requires an understanding of the information on the product, this operator's manual as well as a knowledge of the project you are attempting. Before use of this product, familiarize yourself with all operating features and safety rules.
model number 060-3770-4 | contact us: 1.866.523.5218
Before operating the log splitter, loosen the bleed screw by several rotations, until air is able to enter and escape from the oil tank smoothly. Airflow should be detectable through hole in the bleed screw when the log splitter is in use.
In order to avoid oil leaking from this point, verify that the bleed screw is tightened before moving the log splitter.
MAXIMUM PRESSURE LIMITING
SCREW
The maximum pressure was set before the log splitter left the factory, and the maximum pressure limiting screw is sealed with glue in order to ensure that the log splitter works under pressure that does not exceed 5 tons. The pressure was set by a qualified mechanic using professional instruments.
Unauthorized resetting may cause the hydraulic pump to fail to generate enough splitting pressure, or it may RESULT IN SERIOUS
INJURY AND/OR DAMAGE TO THE
LOG SPLITTER.
!
FAILURE TO LOOSEN THE BLEED SCREW WILL KEEP THE SEALED AIR
IN THE HYDRAULIC SYSTEM COMPRESSED AFTER DECOMPRESSION.
CONTINUOUS COMPRESSION AND DECOMPRESSION OF THE AIR
WILL BLOW OUT THE SEALS OF THE HYDRAULIC SYSTEM, AND WILL
CAUSE PERMANENT DAMAGE TO THE LOG SPLITTER.
!
DO NOT ADJUST THE MAXIMUM PRESSURE LIMITING SCREW.
5
6 model number 060-3770-4 | contact us: 1.866.523.5218
model number 060-3770-4 | contact us: 1.866.523.5218
Item Description
7
8
9
5
6
3
4
1
2
Lever mount nut
Nut cap
Pressing plate
Valve retract spring
Guard plate
Nut
Copper gasket
Screw
O-ring
10 Snap washer-shaft
11 O-ring
12 Valve core rod
13
Sliding pressure sensor sleeve spring
14 Aluminium cover (rear)
15 O-ring
16 Piston
17 Piston ring
18 O-ring
19 Spring
20 Stud
21 Hydraulic cylinder
22 Aluminium cover (front)
23 Piston rod seal
24 O-ring
25 Wing bolt
26 Washer groupware
27 Dipstick
28 Piston rod
29 Screw
30 Frame tube
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
QTY
4
1
1
1
2
1
1
1
3
1
1
1
Item Description
31 Log retaining plate
32 Spring washer
33 Screw
34 Nut
35 Flat washer
36 Nut
37 Nut plug
38 Washer groupware
39 Valve sleeve
40 Spring
41 Adjusting screw
42 Steel ball
43
Pressure limited valve spring
44 Adjusting screw
45
Welded log pusher connection
46 Plastic insert 1
47 Plastic insert 2
48 Log pusher
49 Nut
50 Flat washer
51 Screw
52 Wheel cover
53 Block turn
54 Wheel
55 Washer
56 Wheel shelf
57 Bolt
58 Spring washer
59 Washer
1
1
4
1
6
2
2
4
2
9
9
1
4
1
1
5
QTY
1
1
1
2
2
6
2
2
4
5
1
1
1
7
8 model number 060-3770-4 | contact us: 1.866.523.5218
Item Description
60 Gear pump cover
61 Spring
62 Gear housing plate
63 Circlip
64 Gear shaft
65 Steel ball
66 Gear
67 Pin
68 Washer
69 Bolt
70 Motor cover
71 Seal
72 Nut
73 Screw
74 Motor
75 Fan
76 Block turn
77 Shroud
78 Spring washer
79 Screw
80 Leg
81 Washer
82 Bolt
83 Leg cover
84 Cable and plug
85 Nut
86 Bolt
87 Screw
88 Switch box cover
89 Airproof underlay
QTY
1
1
2
2
3
1
1
3
2
1
11
1
1
1
1
1
1
1
1
3
1
2
1
6
1
1
1
2
1
2
Item Description QTY
90 Connection terminal
91 Capacitor
92 Switch
93 Switch box
94 Waterproof underlay
95 Left motor support shoe
96 Right motor support shoe 1
97 Pin 2
98 Spring 2
1
1
1
1
1
1
99 Sliding sleeve
100 Bolt
101 Fuse
102 Owner’s manual
103 Duo-cut splitting wedge
104 Cable
105 Foot pedal
1
1
1
1
1
4
3
model number 060-3770-4 | contact us: 1.866.523.5218
OPERATING CONDITIONS
This log splitter is intended for household use. It is designed to operate in ambient temperatures between -20 o between -25 o
and 40
and 55 o o
C . The log splitter can be stored or transported in ambient temperatures
C .
ELECTRICAL REQUIREMENTS
Plug the log splitter into a standard 120 V ( 10%) 60 Hz ( 1 Hz) electrical supply that has under-voltage, over-voltage, and over-current protection devices, as well as a residual current device (RCD) with a maximum residual current rated at 0.03 A.
9
WIRING DIAGRAM PLUMBING DIAGRAM
10 model number 060-3770-4 | contact us: 1.866.523.5218
This log splitter is equipped with self-lock switch, which means after pressing down the switch button and releasing the hand, the motor will keep working unless the button is pushed again.
This log splitter is equipped with a foot pedal control system, by assembling the foot pedal. This enables you to control your machine with your foot, freeing up both hands. The foot pedal can be easily assembled and is easy to use.
Do not sit down or sit on the log or kneel down while operating foot pedal. Always keep hands and body out of the splitting zone while activating pedal control.
model number 060-3770-4 | contact us: 1.866.523.5218
A trigger type lock-out device is used in order to avoid accidental pushdown of the hydraulic control lever. In order to operate the hydraulic control lever, pull the trigger backward with the index finger before pushing the hydraulic control lever forward.
After 5 seconds, the pressurized oil will become overheated, which could damage the machine. In the case of an extremely hard log, rotate it 90 o
and try to split it in a different direction. If you are not able to split the log, this means that its hardness exceeds the capacity of the machine, and therefore, the log should be discarded in order to protect the log splitter.
11
!
WARNING! Do not put pressure on the log splitter for more than 5 seconds to force it to split very hard wood.
12 model number 060-3770-4 | contact us: 1.866.523.5218
Always set the log firmly on the log retaining plates and the work table. Make sure the log will not twist, rock, or slip while it is being split. Do not force the blade by splitting the log on the upper part. Doing so may break the blade or damage the machine.
Break log in the direction of its growing grain. Do not place the log across the log splitter to split it. Doing so could be dangerous, and may seriously damage the machine. Do not attempt to split 2 logs at the same time, because one of them may fly out of the log splitter and cause an injury.
FREEING A JAMMED LOG
• Release both controls.
• After the log pusher moves back to its starting position and comes to a complete stop, insert a wedge of wood under the jammed log.
• Start the log splitter in order to push the wedge of wood completely under the jammed log.
• Repeat this procedure with steeper sloped wedges until the log is free.
Do not try to knock the jammed log off.
Knocking the log will damage the log splitter, or it may cause the log to fly out of the log splitter, which could result in an injury.
model number 060-3770-4 | contact us: 1.866.523.5218
REPLACING THE HYDRAULIC OIL
Replace the hydraulic oil in the log splitter after every 150 hours of use. Follow the procedure below.
• Verify that all moving parts have stopped and that the log splitter is unplugged.
• Unscrew the oil drain bolt with dipstick in order to remove it.
• Turn the log splitter onto the support leg over a 4-litre container in order to drain the hydraulic oil.
• Turn the log splitter onto the motor side.
• Refill the log splitter with the proper volume of fresh hydraulic oil, according to the specifications table that applies to the specific model of log splitter.
• Clean the surface of the dipstick on the oil drain bolt, and insert it back into the oil tank, while keeping the log splitter in the vertical position.
• Verify that the level of the refilled oil is between the 2 grooves on the dipstick.
• Clean the oil drain bolt before reinserting it. Tighten the oil drain bolt in order to avoid leakage, and then place the log splitter in the horizontal position.
Check the oil level regularly in order to ensure that it is between the 2 grooves on the dipstick.
When the oil level reaches the lower groove, the oil should be refilled.
SHARPENING THE BLADE
After using the log splitter for some time, sharpen the blade using a fine-toothed file, and smooth out any burrs or crushed areas along the cutting edge.
!
NOTE! Please dispose of used hydraulic oil in a manner that is compatible with the environment.
13
14 model number 060-3770-4 | contact us: 1.866.523.5218
Problem
The log splitter does not split logs.
The wedge cutting edge is blunt.
Cause
The log is not positioned properly.
The size or hardness of the log exceeds the capacity of the machine.
There is an oil leak.
Remedy
Refer to the section entitled
“operation” for instructions on proper log loading.
Reduce the size of the log before splitting it on the log splitter.
Refer to the section entitled
“sharpening the blade” for instructions on how to sharpen the cutting edge
Locate the leak, and call the helpline.
An unauthorized adjustment was made to the maximum pressure limiting screw—a lower maximum pressure was set.
The log pusher moves jerkily, makes an unfamiliar noise, or vibrates excessively.
Not enough hydraulic oil and too much air in the hydraulic system.
Oil leaks around the cylinder ram or from other points.
Air was sealed in the hydraulic system during operation.
The bleed screw was not tightened before moving the log splitter.
The oil drain bolt with dipstick is not tight.
Call the helpline.
Check the oil level, and refill the oil if necessary.
Call the helpline.
Loosen the bleed screw by 3 or 4 rotations before operating the log splitter.
Tighten the bleed screw before moving the log splitter.
Tighten the oil drain bolt with dipstick.
The hydraulic control valve assembly and/or seal is worn.
Call the helpline.
model number 060-3770-4 | contact us: 1.866.523.5218
Symbol Name Designation/Explanation
BEFORE
OPERATING THE
LOG SPLITTER
Read and understand the owner’s manual and all labels affixed to the log splitter. Learn its application and limitations, as well as the specific potential hazards. Always check oil level before using log splitter.
DRUGS,
ALCOHOL, AND
MEDICATION
Do not operate this log splitter while under the influence of drugs, alcohol, or any medication that may affect your ability to use it properly.
AVOID
DANGEROUS
CONDITIONS
Place the log splitter on a stable, flat, and level work surface that is 24 – 30” (60 – 75 cm) high in a location where there is plenty of room for handling. Bolt the log splitter to the work surface if it tends to slip, walk, or slide. Stay alert. Keep the work area clean and well lit. A cluttered work area invites injuries. Do not use the log splitter in wet or damp areas, and do not expose it to rain. Do not use the log splitter in areas where fumes from paint, solvents, or flammable liquids pose a potential hazard.
INSPECT THE
LOG SPLITTER
Inspect the log splitter before turning it on. Keep guards in place and in working order. Always verify that keys and adjusting wrenches are removed from the tool and the area around it before turning it on. Replace damaged, missing, or faulty parts before using the log splitter.
Inspect the log splitter for any malfunctioning or damaged components including the splitting wedge for cracks and deformation. Make all adjustments with power off.
DRESS
PROPERLY
Do not wear loose clothing, gloves, neckties, or jewellery (rings, wrist watches), because they can get caught in moving parts.
Electrically non-conductive protective gloves and non-skid footwear should be worn when working with tools. Wear protective hair covering to contain long hair in order to prevent it from getting caught in machinery. Wear steel-toed shoes.
PROTECT YOUR
EYES AND FACE
A log splitter may throw foreign objects into the eyes, which can cause permanent eye damage. Always wear safety goggles.
Everyday eyeglasses only have impact-resistant lenses.
They are not safety glasses. Do not place the log splitter on the ground when it is in use. Doing so creates an awkward operating position, in which the operator’s face will be close to the machine, which increases the risk of being struck by wood chips or debris.
15
16 model number 060-3770-4 | contact us: 1.866.523.5218
Symbol Name
EXTENSION
CORDS
Designation/Explanation
Improper use of extension cords may cause inefficient operation of the log splitter, which may result in overheating. Verify that the extension cord is no longer than 32.5’ (10 m) and that its crosssection is no less than 1/8” (2.5 mm), in order to allow sufficient current to flow to the motor. Avoid use of loose and inadequatelyinsulated connections. Connections must be made with protected material that is suitable for outdoor use.
AVOID ELECTRIC
SHOCK
Verify that the electric circuit is adequately protected, and that it corresponds to the power, voltage, and frequency of the motor. Verify that there is a ground connection and a regulation differential switch upstream. Ground the log splitter. Prevent contact between your body and grounded surfaces such as pipes, radiators, ranges, and refrigerators. Never open the push-button box on the motor. If it becomes necessary to open this box, contact a qualified electrician. Do not allow your fingers to touch the metal prongs of the plug when plugging in or unplugging the log splitter.
KEEP VISITORS
AND CHILDREN
AWAY
The log splitter must always be operated by only one person.
Always keep other people a safe distance away from the work area, especially when the log splitter is in use. Never ask another person for help in freeing a jammed log.
INSPECT THE
LOG
DO NOT
OVERREACH
Verify that there are no nails or foreign objects in the logs that are to be split. The ends of the logs must be cut square.
Branches must be cut off flush with the trunk.
Inspect the log splitter for any malfunctioning or damaged components including the splitting wedge for cracks and deformation.
Do not work on a slippery floor. Keep proper footing and balance at all times. Never stand on the log splitter. Serious injury could occur if the tool tips or is accidentally jarred. Do not store anything above or near the log splitter such that someone might stand on the tool in order to reach it.
AVOID
INJURY FROM
UNEXPECTED
ACCIDENTS
Always pay attention to the movement of the log pusher. Do not attempt to load a log until the log pusher has stopped. Keep hands out of the way of all moving parts. Do not try to remove split logs until the tool has totally competed its work cycle.
model number 060-3770-4 | contact us: 1.866.523.5218
Symbol Name Designation/Explanation
PROTECT YOUR
HANDS
Keep your hands away from splits and cracks that open in the log. They may close suddenly, which could cause severe crushing or amputation. Do not remove jammed logs using your hands. Never attempt to split more than one log at a time.
Keep hands off the controls while logs are being loaded and unloaded. Ensure the loader and operator are positioned in the safe area at the control end of the log splitter while operating the ram.
DO NOT FORCE
THE TOOL
The tool will work better and safer when used at the rate that it is designed to work at. Do not try to split logs that are larger than those indicated in the specifications table. Doing so could be dangerous, and may damage the machine. Only use the log splitter for its intended purpose.
NEVER LEAVE
THE TOOL
UNATTENDED
WHILE IT IS
RUNNING
Do not leave the tool until it has come to a complete stop.
DISCONNECT
THE POWER
Unplug the log splitter when it is not in use, and before making adjustments, changing parts, cleaning, or working on the log splitter. Consult the technical manual before servicing.
PROTECT THE
ENVIRONMENT
Dispose of used oil only at an authorized collection point, or follow the regulations that are in effect in the area where the log splitter is used. Do not dump used oil into drains, soil, or water.
MAINTAIN THE
LOG SPLITTER
WITH CARE
For best and safest performance, keep the log splitter clean.
MAKE THE
WORKSHOP
CHILDPROOF
Keep the workshop locked. Disconnect master switches. Store the log splitter away from children and others who are not qualified to use it.
17
18 model number 060-3770-4 | contact us: 1.866.523.5218
TWO-YEAR LIMITED WARRANTY
For two (2) years from the date of purchase within Canada, YARDWORKS CANADA will, at its option, repair or replace for the original purchaser, free of charge, any part or parts found to be defective in material or workmanship.
How to Obtain Service:
Warranty service is available by calling the toll-free helpline at 1 866-523-5218.
The factory will not accept the return of a complete unit unless prior written permission has been extended by
YARDWORKS CANADA.
This warranty does not cover:
1. Any part that has become inoperative due to misuse, commercial use, abuse, neglect, accident, improper maintenance, or alteration; or
2. The unit, if it has not been operated and/or maintained in accordance with the owner’s manual; or
3. Normal wear, except as noted below;
4. Routine maintenance items such as lubricants, blade sharpening;
5. Normal deterioration of the exterior finish due to use or exposure.
Full One Hundred Twenty Days (120)
Warranty on Normal Wear Parts:
Normal wear parts are defined as blade adaptors, blades, grass bags and tires.
These parts are warranted to the original purchaser to be free from defects in material and workmanship for a period of one hundred twenty (120) days from the date of retail purchase.
Transportation Charges:
Transportation charges for the movement of any power equipment unit or attachment are the responsibility of the purchaser. The purchaser must pay transportation charges for any part submitted for replacement under this warranty unless such return is requested in writing by YARDWORKS
CANADA.
Other Warranties:
All other warranties, express or implied, including any implied warranty of merchantability is limited in its duration to that set forth in this express limited warranty. The provisions as set forth in this warranty provide the sole and exclusive remedy of YARDWORKS CANADA obligations arising from the sale of its products.
YARDWORKS CANADA will not be liable for incidental or consequential loss or damage.
model number 060-3770-4 | contact us: 1.866.523.5218
19
Made in China. Imported by YardWorks Canada
Toronto, Canada M4S 2B8
