Yamaha | HTR-2064 | manual | Yamaha HTR-2064 User manual

Owner’s Manual
AV Receiver
English
CONTENTS
INTRODUCTION
Features and capabilities ................................................... 3
About this manual............................................................. 4
Supplied accessories......................................................... 4
Part names and functions.................................................. 5
Front panel........................................................................ 5
Rear panel......................................................................... 6
Front panel display ........................................................... 7
Remote control ................................................................. 8
CONNECTIONS
Connecting speakers .......................................................... 9
Speaker channels and functions........................................ 9
Speaker layout ................................................................ 10
Connecting speakers ....................................................... 10
Connecting external devices............................................ 12
Cable plugs and jacks ..................................................... 12
Connecting a TV monitor............................................... 13
Connecting BD/DVD players and other devices ............ 15
Connecting the FM antenna............................................ 17
Setting up speaker parameters .......................................18
STEP 1: Display the setting menu..................................18
STEP 2: Set the speaker status and size ......................... 18
STEP 3: Set the distance from the listening point.......... 19
STEP 4: Playback a test tone.......................................... 20
STEP 5: Adjust the volume ............................................ 20
PLAYBACK
Basic playback procedure ............................................... 21
Adjusting high/low-frequency sound (Tone control) .....21
Changing input settings with a single key
(SCENE function) ............................................................ 22
Registering input sources/sound field program .............. 22
Enjoying sound field programs.......................................22
Selecting sound field programs and sound decoders......22
Sound field programs ..................................................... 24
Remote control............................................................... 53
FM tuning......................................................................... 26
Selecting a frequency for reception (Normal tuning)..... 26
Registering and recalling a frequency (Preset tuning) ... 27
Clearing preset stations .................................................. 29
Glossary............................................................................ 54
Audio information.......................................................... 54
Sound field program information................................... 55
Video information .......................................................... 55
SETUP
Information on HDMI™................................................. 56
Configuring the settings specific for each input source
(Option menu) .................................................................. 30
Option menu display and setup ...................................... 30
Option menu items ......................................................... 30
Specifications.................................................................... 57
About trademarks ........................................................... 56
Index ................................................................................. 58
Setting various functions (Setup menu)......................... 33
Setup menu display and settings .................................... 33
Setup menu items ........................................................... 33
Manages settings for speakers........................................ 34
Setting the audio output function of this unit................. 37
Setting HDMI functions ................................................. 38
Making the receiver easier to use ................................... 40
Setting sound field program parameters......................... 41
Prohibiting setting changes ............................................ 41
Setting sound field program parameters ....................... 42
Setting sound field parameters ....................................... 42
Extended functionality that can be configured
as needed (Advanced Setup menu)................................. 44
Displaying/Setting the Advanced Setup menu............... 44
Avoiding crossing remote control signals when using
multiple Yamaha receivers ............................................. 44
Changing FM frequency steps
(Asia and General models only)..................................... 45
Initializing various settings for this unit......................... 45
Using the HDMI Control function ................................. 46
APPENDIX
Troubleshooting ............................................................... 49
General ........................................................................... 49
HDMI™ ......................................................................... 52
Tuner (FM) ..................................................................... 52
En
2
INTRODUCTION
Features and capabilities
■ Built-in high-quality, high-power 5-channel amplifier
■ 1-button input/sound field program switching (SCENE function) .......................22
■ Speaker connections for 2- to 5.1-channel configurations
– Speaker channels and functions .................................................................................................................9
– Speaker layout..........................................................................................................................................10
– Speaker/subwoofer cable connection.......................................................................................................10
■ Acoustic parameter adjustment to match your speakers and listening
environment
–
–
–
–
–
–
–
Setting for speaker acoustic parameters...................................................................................................18
Specifying the settings for each speaker..................................................................................................34
Volume control for each speaker..............................................................................................................35
Speaker distance settings .........................................................................................................................35
Sound quality control with the equalizer <Graphic Equalizer> ..............................................................36
Test tone speaker adjustment ...................................................................................................................36
Bass and treble level adjustment <Tone Control> ...................................................................................21
■ External device connection and playback
–
–
–
–
–
–
–
–
–
–
Cables and input/output jacks for this unit ..............................................................................................12
TV connection..........................................................................................................................................13
TV audio playback through this receiver .................................................................................................13
Connections for BD/DVD players (recorders) and other devices............................................................15
Audio signal output to the TV connected via the HDMI jack .................................................................39
Correction of lag between audio and video signals <Lipsync>...............................................................37
HDMI video input combining other audio input .....................................................................................31
Changing the input source names <Input Rename> ................................................................................40
Configuring the settings specific for each input source <Option menu> ................................................30
Playback from external devices ...............................................................................................................21
■ Front panel information display
– Front panel display information switching ................................................................................................7
– Front panel display brightness adjustment <Dimmer>............................................................................41
– Digital video/audio signal information display <Signal Info> ................................................................31
■ Volume/sound quality adjustment functions
–
–
–
–
Easy listening at low volumes <Adaptive DRC> ....................................................................................37
Maximum volume settings.......................................................................................................................38
Startup volume settings............................................................................................................................38
Adjusting volume between input sources <Volume Trim> .....................................................................31
■ Remote control operation
– Remote control names and functions.........................................................................................................8
– Insert batteries into the remote control ......................................................................................................4
– Multiple Yamaha receiver operation without signal interference <Remote ID Switching>....................44
■ Other features
–
–
–
–
Standby mode after prolonged non-operation <Auto Power Down function>........................................41
Standby mode after a specific amount of time <Sleep timer>...................................................................8
Initializing various settings for this unit ..................................................................................................45
Prohibiting setting changes <Memory Guard>........................................................................................41
■ FM Tuner
– FM broadcast listening.............................................................................................................................26
– Simple preset tuning ................................................................................................................................27
– Changing FM frequency steps initializing various settings for this unit .................................................26
■ Multi-channel, multi-format playback
–
–
–
–
–
Sound field effect selection......................................................................................................................22
Playback without sound field effects .......................................................................................................23
Stereo playback........................................................................................................................................23
Sound field effect configuration...............................................................................................................42
Compressed-music playback ...................................................................................................................22
En
3
INTRODUCTION
Features and capabilities
About this manual
• This manual is printed prior to production. Design and
specifications are subject to change in part as a result of
improvements, etc. In case of differences between the manual and
product, the product has priority.
• “dHDMI1” (example) indicates the name of the parts on the
remote control. Refer to the “Remote control” (☞p. 8) for the
information about each position of the parts.
• J1 indicates that the reference is in the footnote. Refer to the
corresponding numbers on the bottom of the page.
• ☞ indicates the page describing the related information.
• Click on the “
” at the bottom of the page to display the
corresponding page in “Part names and functions.”
Front panel
Rear panel
Front panel display
Remote control
Supplied accessories
■ Installing batteries in the remote control
Check that you received all of the following parts.
When inserting batteries in the remote control, remove the
battery compartment cover from the reverse side of the remote
control, and insert two AAA batteries into the battery
compartment so that they match with the polarity markings (+
and -).
a
Remote control
Batteries (2)
(AAA, R03, UM-4)
Battery compartment
cover
c
b
Battery compartment
Indoor FM antenna
(for U.S.A., Canada, General,
and Asia models)
Indoor FM antenna
(for U.K., Europe and Australia
models)
Replace the batteries with new ones if the following symptoms
become evident:
• The remote control can only be operated within a narrow range.
• bTRANSMIT does not light up, or only lights dimly.
NOTE
CD-ROM
(Owner’s Manual)
If there are remote control codes for external components
registered to the remote control, removing the batteries for more
than two minutes, or leaving exhausted batteries in the remote
control, the remote control codes may be cleared. If this should
occur, replace the batteries with new ones, and set the remote
control codes.
En
4
INTRODUCTION
Part names and functions
g MUTE
Front panel
h
a A (Power)
Switches this unit between on and standby modes.
b INFO
i
Changes the information shown on the front panel display (☞p. 7).
c MEMORY
d
e
f
j
Registers FM stations as preset stations (☞p. 28). J1
PRESET j / i
Selects an FM preset station (☞p. 28). J1
TUNING jj / ii
Changes FM tuner frequencies (☞p. 26). J1
FM MODE
Switch FM reception stereo and monaural (☞p. 27). J1
a
k
l TONE CONTROL
Switch muted and non-muted.
Front panel display
Displays information on this unit (☞p. 7).
PHONES jack
For plugging headphones in. Sound effects applied during playback
can also be heard through the headphones.
INPUT l / h
Selects an input source from which to playback. Press either the left or
right key repeatedly to cycle through the input sources in order.
SCENE
Switches the input source and the sound field program with a single
button (☞p. 22). Press this key when this unit is in standby mode to
switch on the unit.
b
c
d
e
INFO
MEMORY
PRESET
TUNING
Adjusts high-frequency/low-frequency output of speakers/headphones
(☞p. 21).
m PROGRAM l / h
Switches between the sound field effect (sound field program) you are
using and the surround sound decoder (☞p. 22). Press either the left
or right key repeatedly to cycle through the input sources in order.
n STRAIGHT
Changes a sound field program to straight decoding mode (☞p. 23).
o VOLUME
Adjusts the volume level.
fg h
FM MODE
MUTE
VOLUME
SCENE
BD
DVD
PHONES
INPUT
TONE CONTROL
TV
CD
RADIO
PROGRAM
STRAIGHT
m
n
SILENT CINEMA
i
j
k l
o
J 1 : Usable when you have selected tuner input.
En
5
INTRODUCTION
Part names and functions
c ANTENNA jacks
Rear panel
d
a HDMI OUT jack
b
For connecting an HDMI - compatible TV to output audio/video
signals to (☞p. 13).
HDMI1-3 jacks
For connecting external components equipped with HDMIcompatible outputs to receive audio/video signals from (☞p. 15).
a
e
f
g VOLTAGE SELECTOR
For connecting an FM antenna (☞p. 17).
AUDIO1-6 jacks
For connecting to external components equipped with audio outputs to
input audio signals into this unit (☞p. 16).
SUBWOOFER jack
For connecting a subwoofer with a built-in amplifier (☞p. 11).
SPEAKER terminals
For connecting the front, center, and surround speakers, and a
subwoofer (☞p. 11).
b
h
(General model only)
Select the switch position according to your local voltage using a
straight slot screwdriver.
Voltages are AC 110-120/220-240 V, 50/60 Hz.
Power cord
For connecting this unit to an AC wall outlet.
c
Distinguishing the input and output jacks
The area around HDMI OUT and
SUBWOOFER jacks is marked in white to
prevent connection errors. Use these jacks to
output audio/video signals to a TV or a
subwoofer.
Output jacks
ARC
ANTENNA
HDMI OUT
(BD/DVD)
HDMI 2
HDMI 1
FM
HDMI 3
VOLTAGE
SELECTOR
75
SPEAKERS
FRONT
AUDIO 1
AUDIO 2
AUDIO 3
AUDIO 4
OPTICAL
COAXIAL
COAXIAL
OPTICAL
(CD)
( TV )
AUDIO 5
CENTER
SURROUND
SUB
WOOFER
110V120V
220V240V
AUDIO 6
ANTE
HDMI
HDMI 2
AUDIO 1
AUDIO 2
AUDIO 3
AUDIO 4
OPTICAL
COAXIAL
COAXIAL
OPTICAL
(CD)
( TV )
SUBWOOFER
FM
HDMI 3
AUDIO 5
AUDIO 6
SUBWOOFER
d
e
f
g
h
CAUTION
(General model only)
The VOLTAGE SELECTOR on the rear panel
of this unit must be set for your local voltage
BEFORE plugging the power cable into the
AC wall outlet. Improper setting of the
VOLTAGE SELECTOR may cause damage to
this unit and create a potential fire hazard.
VOLTAGE SELECTOR
SELECTOR
110V120V
220V240V
En
6
INTRODUCTION
Part names and functions
Front panel display
g Cursor indicators
a HDMI indicator
h
b
c
d
e
f
Lights up when HDMI signals are input at the selected HDMI input
source.
CINEMA DSP indicator
Lights up when a sound field effect that uses CINEMA DSP
technology is selected.
Tuner indicator
Lights up when receiving an FM broadcast.
SLEEP indicator
Lights up when the sleep timer is activated (☞p. 8).
MUTE indicator
Flashes when audio is muted.
VOLUME indicator
Displays the current volume level.
i
■ Changing the front panel display
Light up if corresponding cursors on the remote control are available
for operations.
Multi information display
Displays a range of information on menu items and settings.
Speaker indicators
Indicate speaker terminals from which signals are output.
The front panel can display sound field programs and surround
decoder names as well as the active input source.
Press fINFO repeatedly to cycle through input source →
sound field program → surround decoder in order. J1
Input source name
Subwoofer
Front speaker L
Surround speaker L
a
L
SL
SW
C
Center speaker
R
SR
HDMI1
Front speaker R
STRAIGHT
Surround speaker R
L
SL
SW
C
R
SR
Sound field program (DSP program)
b
c
d
SLEEP
STEREO
TUNED
e
f
VOL.
MUTE
L
SL
g
VOL.
h
g
SW
C
R
SR
i
J 1 : While selecting a tuner input, the FM frequency is displayed instead of the input source.
En
7
INTRODUCTION
Part names and functions
a Remote control signal transmitter
Remote control
Transmits infrared signals.
b TRANSMIT
Lights up when a signal is output from the remote control.
a
c Input selector
Select an input source on this unit from which to playback.
TRANSMIT
j
b
RECEIVER
k
SLEEP
HDMI
c
1
2
3
1
2
3
4
5
6
HDMI1-3
AUDIO1-6
HDMI1-3 jacks
AUDIO1-6 jacks
d TUNER keys
Operates the FM tuner. These keys are used when using the tuner
input.
i Cursor B / C / D / E, ENTER, RETURN
Cursor B / C / D / E Select menu items and change settings when
settings menus, etc are displayed.
ENTER
Confirms a selected item.
RETURN
Returns to the previous screen when setting
menus are displayed, or ends the menu display.
j SLEEP
Sets this unit to place itself in standby mode automatically after a
specified period of time has elapsed (sleep timer). Press this key
repeatedly to set the time for the sleep timer function. The front panel
display indicator lights up when the sleep timer is activated.
AUDIO
TUNER
MEMORY
PRESET F / G
TUNING H / I
TUNER
d
e INFO
TUNER
Cycles the information displayed on the front panel display (the name
of the currently selected input source, the sound field program, the
surround decoder, the FM tuner frequency, etc.)(☞p. 7).
MEMORY
PRESET
e
TUNING
INFO
ENHANCER
MOVIE
f
SOUND
MUSIC
f SOUND selection keys
STEREO
Switch between the sound field effect (sound field program) you are
using and the surround decoder (☞p. 22).
STRAIGHT SUR. DECODE
SCENE
g
BD
DVD
FM tuner
Presets radio stations.
Selects a preset station.
Changes tuning frequencies.
TV
SETUP
CD
l
OPTION
h
ENTER
g SCENE
RADIO
VOLUME
m
i
Switches the input source and the sound field program with a single
button (☞p. 22). Press this key when this unit is in standby mode to
switch on the unit.
Sleep 120min.
Sleep Off
Sleep 90min.
Sleep 30min.
Sleep 60min.
k RECEIVER A (RECEIVER Power)
Switches this unit between on and standby modes.
l OPTION
Displays the Option menu for each input source (☞p. 30).
m VOLUME +/Adjusts the volume level (☞p. 21).
n MUTE
Turns the mute function of the sound output on and off (☞p. 21).
h SETUP
Displays a detailed Setup menu for this unit (☞p. 33).
RETURN
MUTE
n
En
8
CONNECTIONS
Connecting speakers
This unit uses acoustic field effects and sound decoders to bring you the impact of a real movie theater or concert hall. These effects will be brought to you with ideal speaker positioning and
connections in your listening environment.
■ Surround left and right speakers
Speaker channels and functions
The surround speakers are for effect and vocal sounds with the 5.1-channel speakers providing reararea sounds.
■ Front left and right speakers
The front speakers are used for the front channel sounds (stereo sound) and effect sounds.
Ex.
Ex.
Front speaker layout:
Place these speakers at an equal distance from the ideal listening position in the front of the room.
When using a projector screen, the appropriate top positions of the speakers are about 1/4 of the screen
from the bottom.
■ Center speaker
The center speaker is for the center channel sounds (dialog, vocals, etc.).
Surround speaker layout:
Place the speakers at the rear of the room on the left and right sides facing the listening position. They
should be placed between 60 degrees and 80 degrees from the listening position and with the speaker
tops at a height of 1.5 – 1.8 m from the floor.
■ Subwoofer
The subwoofer speaker is used for bass sounds and low-frequency effect (LFE) sounds included in
Dolby Digital and DTS.
Ex.
Center speaker layout:
Place it halfway between the left and right speakers. When using a TV, place the speaker just above or
just under the center of the TV with the front surfaces of the TV and the speaker aligned.
When using a screen, place it just under the center of the screen.
Ex.
Subwoofer speaker layout:
Place it exterior to the front left and right speakers facing slightly inward to reduce echoes from the
wall.
En
9
CONNECTIONS
Connecting speakers
Speaker layout
Connecting speakers
5.1-channel speaker layout (5 speakers + subwoofer)
Connect your speakers to their respective terminals on the rear panel.
Front speaker
Front speaker R
R
Surround speaker
L
R
L
Front speaker L
Subwoofer
ANTENNA
FM
VOLTAGE
SELECTOR
75
SPEAKERS
FRONT
CENTER
SURROUND
SUB
WOOFER
110V120V
220V240V
SUBWOOFER
Surround
speaker R
Center speaker
Center speaker
Surround speaker L
About how to install the speakers, please refer to the instruction manual of the speaker.
• Connect at least two speakers (front left and right).
• If you cannot connect all five speakers, give priority to the surround speakers.
• The surround speakers should be placed between 60 degrees and 80 degrees from the listening position.
Subwoofer
CAUTION
• Remove the AC power cord of this unit from the power outlet before connecting the speakers.
• Generally speaker cables consist of two parallel insulated cables. One of these cables is a different
color, or has a line running along it, to indicate different polarity. Insert the different colored (or lined)
cable into the “+” (positive, red) terminal on this unit and the speakers, and the other cable into the “-”
(minus, black) terminal.
• Be careful that the core of the speaker cable does not touch anything or come into contact with the metal
areas of this unit. This may damage this unit or the speakers. If the speaker cables short circuit, “Check
SP Wires” will appear on the front panel display when this unit is switched on.
• Use speakers having more than 6 Ω impedance when you use other than the speakers that are included
in the Yamaha Home Theatre Package.
• Use a subwoofer that is active (built-in amplier) and turn it off before connecting to the unit when you
use other than the subwoofer that is included in the Yamaha Home Theatre Package.
En
10
CONNECTIONS
Connecting speakers
■ Connecting speakers / a subwoofer
■ Connecting an active subwoofer
Connect to a subwoofer jack as follows when using an active
subwoofer.
FR
ON
SP
EA
T
KE
RS
CE
NT
ER
4
2
SU
RR
OU
ND
3
S
WO UB
OF
ER
1
1
2
3
4
Remove approximately 10mm of insulation from the
ends of the speaker cables, and twist the bare wires
of the cables together firmly so that they will not
cause short circuits.
Press the tab on the speaker terminal down.
1
Connect the subwoofer input jack to the
SUBWOOFER jack on this unit with an audio pin
cable.
2
Set the subwoofer volume as follows.
Volume: Set to approximately half volume (or slightly less than
half).
Crossover frequency (if available): Set to maximum.
VOLUME
CROSSOVER/
HIGH CUT
Insert the speaker cable end into the terminal.
MIN
Lift the tab to fix the speaker cable in place.
MAX
MIN
MAX
Subwoofer examples
En
11
CONNECTIONS
Connecting external devices
■ Audio jacks
Cable plugs and jacks
The main unit is equipped with the following input/output jacks. Use jacks and cables appropriate for
components that you are going to connect.
■ Audio/Video jacks
OPTICAL jacks
COAXIAL jacks
These jacks transmit optical digital audio signals.
Use fiber-optic cables for optical digital audio
signals.
These jacks transmit coaxial digital audio signals.
Use pin cables for digital audio signals.
HDMI jacks
AUDIO 4
AUDIO 2
Digital video and digital sound are transmitted through a single jack.
Only use an HDMI cable.
OPTICAL
(TV)
COAXIAL
Digital audio fiber-optic cable
Digital audio pin cable
HDMI cable
AUDIO jacks
• Use a 19-pin HDMI cable with the HDMI logo.
• We recommend using a cable less than 5.0 m long to prevent signal quality degradation.
These jacks transmit conventional analog audio
signals.
Use stereo pin cables, connecting the red plug to
the red R jack, and the white plug to the white L
jack.
AUDIO 5
Stereo audio pin cable
En
12
CONNECTIONS
Connecting external devices
■ Listening to TV audio
Connecting a TV monitor
To transmit sound from the TV to this unit, connect as followings according to the TV:
■ Connecting an HDMI video monitor
When using a TV that supports the Audio Return Channel function and HDMI
Control function
Connect the HDMI cable to the HDMI OUT jack.
HDMI
HDMI OUT
HDMI input
(BD/DVD)
HDMI 2
HDMI 1
HDMI 3
HDMI
HDMI
AUDIO 1
AUDIO 2
AUDIO 3
AUDIO 4
OPTICAL
COAXIAL
COAXIAL
OPTICAL
(CD)
( TV )
AUDIO 5
When your TV supports both HDMI Control (Ex. Panasonic VIERA Link) and Audio Return Channel
functions, audio/video output from the unit to the TV and audio output from the TV to the unit are
possible using a single HDMI cable.
The input source is switched automatically to match operations carried out on the TV, and that makes
TV sound control easier to use.
For the connections and settings, refer to “Single HDMI cable input to TV audio with Audio Return
Channel function” (☞p. 48).
When using a TV that supports the HDMI Control functions
AUDIO 6
TV
When using a TV that supports HDMI Control functions (Ex. Panasonic VIERA Link), if HDMI
Control functions are enabled on the unit, then input source can be switched automatically to match
operations carried out on the TV.
For the connections and settings, refer to “Switching the input source on this unit automatically when
listening to TV audio” (☞p. 47).
• Use a 19-pin HDMI cable with the HDMI logo.
• We recommend using a cable less than 5.0 m long to prevent signal quality degradation.
• When using a TV that supports Audio Return Channel function, audio/video signals can be transmitted
mutually between the unit and TV with a single HDMI cable (☞p. 48).
En
13
CONNECTIONS
Connecting external devices
When using other TVs
To transmit sound from the TV to this unit, connect its AUDIO 1-6 jacks to the TV’s audio output
jacks.
Depending on the connection on TV, connect the TV’s audio output to the AUDIO 1-6.
TV audio output
Connection
Optical digital audio output
Connect to AUDIO 1 or AUDIO 4 OPTICAL jack with a fiber-optic cable.
Coaxial digital audio output
Connect to AUDIO 2 or AUDIO 3 COAXIAL jack with a digital audio pin
cable.
Analog stereo output
Connect to AUDIO 5 or AUDIO 6 jack with a stereo pin cable.
Select the input source connected via TV’s audio output jack to enjoy the TV sound.
If the TV supports optical digital audio output, we recommend that you connect the TV audio output to
the receiver’s AUDIO 4 jack.
Connecting to AUDIO 4 allows you to switch the input source to AUDIO 4 with just a single key
operation using the SCENE function (☞p. 22).
Available input jacks
Audio output
(Optical)
HDMI OUT
(BD/DVD)
HDMI 2
HDMI 1
HDMI 3
OPTICAL
O
OPTICAL
COAXIAL
COAXIAL
OPTICAL
(CD)
( TV )
TV
O
En
14
CONNECTIONS
Connecting external devices
TRANSMIT
Connecting BD/DVD players and other devices
RECEIVER
SLEEP
HDMI
1
2
3
1
2
3
4
5
6
c
This unit has the following input jacks. Connect them to the appropriate output jacks on
the external components.
AUDIO
Input jack
Video input
■ Receiving audio from other input sources
This unit can use the AUDIO 1-6 input jacks to receive audio signals from other audio
input sources.
For example, if an external device cannot produce audio signals from an HDMI jack,
use the following method to change the audio input.
Audio input
TUNER
HDMI1-3
HDMI
HDMI
TUNING
AUDIO 1, 4
—
Optical digital
ENHANCER
AUDIO 2, 3
—
Coaxial digital
AUDIO 5, 6
—
Analog (Stereo)
TUNER
HDMI/Audio (Optical)
output
MEMORY
PRESET
INFO
MOVIE
SOUND
MUSIC
OPTICAL
SETUP
O
CD
RADIO
OPTION
ENTER
l
VOLUME
RETURN
■ Connecting BD/DVD players and other devices with
AUDIO 2
AUDIO 3
AUDIO 4
COAXIAL
COAXIAL
OPTICAL
(CD)
( TV )
AUDIO 5
AUDIO 6
O
HDMI
i Connect the device with an HDMI cable to one of the HDMI1-3 jacks.
Select the HDMI input (HDMI1-3) that the external device is connected to for
playback.
MUTE
HDMI OUT
(BD/DVD)
HDMI
HDMI output
HDMI
HDMI
c Input selector
i Cursor C / D / E
i ENTER
l OPTION
HDMI 3
HDMI
SCENE
TV
HDMI 2
HDMI
OPTICAL
BD
DVD
(BD/DVD)
HDMI
STEREO
STRAIGHT SUR. DECODE
HDMI OUT
AUDIO 1
AUDIO 2
AUDIO 3
AUDIO 4
OPTICAL
COAXIAL
COAXIAL
OPTICAL
(CD)
( TV )
AUDIO 5
AUDIO 6
BD/DVD player
1
2
3
4
Use the cInput selector to select the desired HDMI input source.
Press lOPTION to display the Option menu. J1
Press iCursor C until “Audio In” is displayed, and then press
iENTER.
Press iCursor D / E to select the audio input source.
Inputs that change the audio source
HDMI1
BD/DVD player
VOL.
Audio;;;AUDIO1
L
SL
SW
C
R
SR
Assignable audio input jacks
If you have selected AUDIO 1 input audio (optical digital)
5
Once you have completed the setup, press lOPTION to close the
Option menu.
J 1 : See the section on “Configuring the settings specific for each input source (Option menu)” for details on
the Option menu (☞p. 30).
En
15
CONNECTIONS
Connecting external devices
■ Connecting CD players and other audio devices
Using coaxial digital output sources
Select the audio input (AUDIO 2 or AUDIO 3) that the external device is connected to for playback.
Using analog stereo output sources
Select the audio input (AUDIO 5 or AUDIO 6) that the external device is connected to for playback.
HDMI OUT
HDMI OUT
(BD/DVD)
HDMI 2
HDMI 1
HDMI 2
HDMI 1
HDMI 3
Audio (Coaxial) output
Audio output
AUDIO 1
AUDIO
OPTICAL
COAXIAL
L
HDMI 3
(BD/DVD)
AUDIO 1
AUDIO 2
AUDIO 3
OPTICAL
COAXIAL
COAXIAL
AUDIO 4
COAXIAL
COAXIAL
OPTICAL
(CD)
( TV )
C
AUDIO 5
AUDIO 6
C
AUDIO 4
OPTICAL
(CD)
( TV )
L
R
R
CD player
CD player
Using optical digital output sources
Select the audio input (AUDIO 1 or AUDIO 4) that the external device is connected to for playback.
HDMI OUT
We recommend connecting audio devices with an coaxial digital output to the AUDIO 3 coaxial
digital jack on this unit. This connection allows you to switch to the AUDIO 3 just by pressing the
“CD” SCENE key (☞p. 22).
(BD/DVD)
HDMI 2
HDMI 1
HDMI 3
Audio (Optical) output
OPTICAL
AUDIO 1
AUDIO 2
AUDIO 3
OPTICAL
COAXIAL
COAXIAL
OPTICAL
(CD)
( TV )
AUDIO 5
AUDIO 6
O
O
CD player
En
16
CONNECTIONS
Connecting the FM antenna
An indoor FM antenna is included with this receiver. Connect these antenna properly to the ANTENNA
jack.
Indoor FM antenna
ANTENNA
HDMI 3
FM
VOL
SELE
75
SPEAKERS
FRONT
AUDIO 6
CENTER
SURROUND
SUB
WOOFER
110V120V
220V240V
■ Improving FM reception
We recommend using an outdoor antenna. For more information, consult the nearest authorized
dealer.
En
17
CONNECTIONS
Setting up speaker parameters
TRANSMIT
RECEIVER
SLEEP
HDMI
1
2
3
1
2
3
4
5
6
AUDIO
STEP 1: Display the setting menu
STEP 1: Display the setting menu
1
2
Display the Setup menu from which you can configure
all settings for this unit, and then display the menu for
speaker settings.
TUNER
TUNER
MEMORY
PRESET
When you have finished connecting your speakers,
configure this unit so that they output sound normally.
Carry out the following steps to configure this unit.
TUNING
INFO
STEP 2: Set the speaker status and size
ENHANCER
MOVIE
SOUND
MUSIC
STEREO
Set the size and connection status of speakers and
subwoofers, and whether to designate a specific speaker
(or subwoofer) for low-frequency sound.
STRAIGHT SUR. DECODE
SCENE
BD
DVD
TV
SETUP
CD
RADIO
OPTION
ENTER
RETURN
MUTE
i
The settings in step 2 are not necessary with the
following speaker configuration:
– Subwoofer: connected
– Front speaker: woofer diameter is 16 cm or larger
– Center/surround speakers: woofer diameter is 16 cm or
smaller
Press hSETUP on the remote control.
The Setup menu that allows you to configure all
parameters on this unit appears. J1
SETUP
VOL.
SpeakerSetup
h STEP 3: Set the distance from the listening
VOLUME
Switch this unit on.
L
SL
SW
C
R
SR
point
Set the distance between the speakers and the listening
point so that the sound from each speaker reaches the
listening point at the appropriate timing.
STEP 4: Playback a test tone
Playback a test tone to allow you to configure sound
volumes while listening to the actual effect your settings
are having.
3
Check that “Speaker Setup” appears and
press iENTER.
SP SET
Config
STEP 2: Set the speaker status and
size
4
Check that “Config” appears and press
iENTER.
CONFIG
VOL.
Subwoofer;;Yes
L
SL
SW
C
R
SR
VOL.
L
SL
SW
C
R
SR
Continues to the
next page
This completes step 1.
STEP 5: Adjust the volume
Adjust the volume for each speaker and configure them
so that the sound is balanced.
h SETUP
i ENTER
J 1 : See the section “Setting various functions (Setup menu)” for
details on the Setup menu (☞p. 33).
En
18
CONNECTIONS
Setting up speaker parameters
TRANSMIT
RECEIVER
SLEEP
HDMI
1
2
3
1
2
3
4
5
6
5
AUDIO
Use iCursor B / C to select the speaker
(subwoofer) you want to configure, and
then use iCursor D / E to select speaker
status and size.
Information
TUNER
TUNER
MEMORY
PRESET
Subwoofer
Sets the subwoofer status.
Yes / None
Front
Selects the size (sound
reproduction capacity) of the
front speakers.
Small /
Large
Selects the size of the center
speakers. Choose “None” if
you do not have a center
speaker connected.
None /
Small /
Large
Selects the size of the surround
speakers. Choose “None” if
you do not have surround
speakers connected.
None /
Small /
Large
Audio with a frequency below
this limit will be output from
the subwoofer or the front
speakers.
40Hz to
200Hz
SWFR Phase
Switches the phase of the
subwoofer.
NRM / REV
Extra Bass
Selects whether to play front
channel low-frequency
components through either of
the front speakers or the
subwoofer (Off), or through
both the subwoofer and front
speakers (On).
On / Off
ENHANCER
MOVIE
MUSIC
STEREO
STRAIGHT SUR. DECODE
Center
SCENE
BD
DVD
TV
SETUP
CD
RADIO
OPTION
ENTER
Setting
• Whether or not you set “Crossover,” “SWFR Phase,”
and “Extra Bass” is optional. Check how the effects
sound and then configure them to your liking.
• Use the following as a guide when setting speaker
sizes.
8
Press iCursor B / C to select the speaker
that you want to configure, and press
iCursor D / E to change the distance.
If necessary, you can change the setting units under
“Unit.”
Information
Description
Setting
TUNING
INFO
SOUND
Description
■ The case of general speakers
VOLUME
i
Sur. LR
RETURN
MUTE
Crossover
i Cursor B / C / D / E
i ENTER
i RETURN
This setting is not needed when you use the speakers
that are included in the Yamaha Home Theatre
Package.
Woofer diameter
• 16 cm or larger → Large
• 16 cm or smaller → Small
When speaker size is set to “Small,” low-frequency
components of the speakers you configured are
produced from the subwoofer (or from the front
speakers if there is no subwoofer).
When you have completed the settings for one speaker,
repeat the same procedure for all speakers to complete
settings.
6
Unit
Switches between setting
units (feet / meters).
meters (m) /
feet (ft)
Front L
Front speaker L
0.30 m to 24.00 m
(1.0 ft to 80.0 ft)
Front R
Front speaker R
0.30 m to 24.00 m
(1.0 ft to 80.0 ft)
Center
Center speaker
0.30 m to 24.00 m
(1.0 ft to 80.0 ft)
Sur. L
Surround speaker L
0.30 m to 24.00 m
(1.0 ft to 80.0 ft)
Sur. R
Surround speaker R
0.30 m to 24.00 m
(1.0 ft to 80.0 ft)
SWFR
Subwoofer
0.30 m to 24.00 m
(1.0 ft to 80.0 ft)
When you have completed the settings for one speaker,
repeat the same procedure for all speakers to complete
settings.
Press iRETURN when setting is complete.
Return to the previous menu.
This completes step 2.
STEP 3: Set the distance from the
listening point
7
Press iCursor C to display “Distance” and
press iENTER.
DIST
9
Press iRETURN when setting is complete.
Return to the previous menu.
This completes step 3.
Continues to the
next page
VOL.
Unit;;;;meters
L
SL
SW
C
R
SR
En
19
CONNECTIONS
Setting up speaker parameters
TRANSMIT
STEP 4: Playback a test tone
HDMI
1
2
3
1
2
3
4
5
6
10
AUDIO
Press iCursor C repeatedly to display
“Test Tone” and press iENTER.
TEST
TUNER
TUNER
PRESET
TUNING
INFO
13
L
SL
SW
C
Press iCursor B repeatedly to display
“Level” and press iENTER.
LEVEL
VOL.
>OffOn
MEMORY
STEP 5: Adjust the volume
VOL.
d
RECEIVER
SLEEP
FL----d----
R
SR
L
SL
SW
C
16
Repeat steps 14 and 15 to adjust the
volume balance for all speakers to your
preference.
17
Press iRETURN when setting is
complete.
Return to the previous menu.
R
SR
This completes step 5.
ENHANCER
MOVIE
SOUND
MUSIC
STEREO
11
STRAIGHT SUR. DECODE
SCENE
BD
DVD
TV
SETUP
CD
RADIO
h
OPTION
ENTER
VOLUME
Use iCursor D / E to select “On.”
A test tone plays back as soon as you select “On.”
The test tone plays back in a clockwise fashion, as
follows.
14
The front panel display shows the speaker that is
outputting the test tone. J1
i
Front L
RETURN
Center
Front R
MUTE
Information
Subwoofer
Surround L
h SETUP
i Cursor B / C / D / E
i ENTER
i RETURN
Use iCursor B / C to switch the speaker
that is outputting the test tone, looking
for speakers with a different volume level
to the others.
12
18
19
Repeat procedures 10-12 (step 4) to stop
playback of the test tone.
Once you have completed all settings,
press hSETUP to close the Setup menu.
Speakers
FL
Front speaker L
FR
Front speaker R
C
Center speaker
SL
Surround speaker L
SR
Surround speaker R
SWFR
Subwoofer
Surround R
Check that the test tone is playing back
and press iRETURN.
Return to the previous menu.
This completes step 4.
15
If you find a speaker with a different
volume level to the others, use iCursor
D / E to adjust the volume. Use Front
speaker L or R as a default when
adjusting volumes.
To raise the volume: Press iCursor E.
To lower the volume: Press iCursor D.
J 1 : Only speakers configured for use in procedure 5 output the test
tone.
En
20
PLAYBACK
TRANSMIT
Basic playback procedure
RECEIVER
SLEEP
HDMI
1
2
3
1
2
3
4
5
6
c
AUDIO
TUNER
TUNER
MEMORY
PRESET
1
2
ENHANCER
MOVIE
MUSIC
SETUP
TV
CD
Adjusting high/low-frequency sound
(Tone control)
You can adjust the balance of the high-frequency range
(Treble) and low-frequency range (Bass) of sounds
output from the front left and right speakers to obtain
desired tone.
STEREO
STRAIGHT SUR. DECODE
3
SCENE
BD
DVD
Turn on this unit and select the input source
using cInput selector.
The name of the selected input source is displayed for
a few seconds. J1
TUNING
INFO
SOUND
Turn on external components (TV, BD
player, etc.) connected to this unit.
RADIO
OPTION
Play the external component that you have
selected as the source input, or select a
radio station on the tuner.
VOLUME
m
Refer to the instruction manuals provided with the
external component for details on playback.
MUTE
n
For details on how to tune in to FM stations, refer to
“FM tuning” (☞p. 26).
RETURN
The tone control of the speakers or headphones can be
set separately. Set the headphone tone control with the
headphones connected.
1
Press TONE CONTROL on the front panel
repeatedly to select “Treble” or “Bass.”
2
Press PROGRAM l / h to adjust the output
level in those frequency ranges.
Adjustable range
-6.0 dB to +6.0 dB
Adjustment
increments
0.5 dB
When “Treble” and “Bass” are both 0.0 dB, the audio
signal will bypass the tone control circuit, the “Bypass”
is displayed on the front panel display.
The display returns to the previous display soon after
you release the key.
If you set the balance extremely off, sounds may not
match those from other channels well.
TONE CONTROL
4
Press mVOLUME +/- to adjust the volume.
INFO
MEMORY
PRESET
TUNING
To mute the output.
Press nMUTE to mute the audio output.
Press nMUTE again to unmute.
FM
SCENE
BD
DVD
PHONES
INPUT
TONE CONTROL
TV
CD
RADIO
STRAIGHT
PROGRAM
SILENT CINEMA
PROGRAM l / h
The current setting is displayed on the front panel
display.
c Input selector
m VOLUME +/n MUTE
TONE
Treble
VOL.
0.0dB
L
SL
SW
C
R
SR
J 1 : You can change the input source name displayed on the front
panel display as necessary (☞p. 40).
En
21
PLAYBACK
Changing input settings with a single key (SCENE function)
TRANSMIT
RECEIVER
SLEEP
HDMI
1
2
3
1
2
3
4
5
6
PRESET
TUNING
AUDIO
TUNER
This unit has a SCENE function that allows you to turn the power on and change input sources and sound field programs with one key.
c Four scenes are available for different uses, such as
playing movies or music. The following input sources
and sound field programs are provided as the initial
factory settings.
Registering input sources/sound
field program
3
Press the gSCENE key until “SET
Complete” appears on the front panel
display.
TUNER
MEMORY
SCENE
Input
Sound field program
INFO
ENHANCER
MOVIE
SOUND
MUSIC
STEREO
STRAIGHT SUR. DECODE
f
SCENE
BD
DVD
SETUP
TV
CD
RADIO
OPTION
BD/DVD
HDMI 1
STRAIGHT
TV
AUDIO 4
STRAIGHT
CD
AUDIO 3
STRAIGHT
RADIO
TUNER
5ch Enhancer
g
1
2
Use cInput selector to select the input
source you want to register.
Use the fSOUND selection keys to select
the sound field program you want to
register.
SCENE1
VOL.
SET Complete
L
SL
SW
C
R
SR
Release the key when “SET Complete” is displayed.
Press one key repeatedly to select the sound field
program in the same category. For details on sound
field program, refer to “Selecting sound field programs
and sound decoders” on this page.
VOLUME
RETURN
MUTE
Enjoying sound field programs
This unit is also equipped with a Yamaha digital sound field processing (DSP) chip. You can enjoy multi-channel playback for almost any sound source using various
sound field programs stored on the chip, and a range of sound decoders.
c Input selector
f SOUND selection keys
f MOVIE
f MUSIC
f STEREO
f SUR. DECODE
f STRAIGHT
g SCENE
Selecting sound field programs and
sound decoders
Selects sound field program:
This unit offers sound field settings (sound field
programs) in many different categories suitable for
movies, music and other uses. Choose a sound field
program that sounds best with the source you are playing
back, rather than relying on the name or explanation of
the program.
Selects stereo reproduction:
• Sound field programs are stored for each input source.
When you change the input source, the sound field
program previously selected for that input source is
applied again.
• If the sampling frequency of an input source is higher
than 96 kHz, this unit does not apply any sound field
programs.
MOVIE category: Press fMOVIE repeatedly.
MUSIC category: Press fMUSIC repeatedly.
Press fSTEREO repeatedly.
Selects Compressed Music Enhancer:
Press fSTEREO repeatedly.
Selects surround decoder:
Press fSUR. DECODE repeatedly.
Switches Straight decoding mode (☞p. 23):
Press fSTRAIGHT.
Sound field program categories
MOVIE
VOL.
Sci-Fi
L
SL
SW
C
R
SR
Program
• You can use the speaker indicators on the front panel
display to check what speakers are currently
outputting sound (☞p. 7).
• You can adjust sound field elements (sound field
parameters) for each of the programs.
En
22
PLAYBACK
Enjoying sound field programs
TRANSMIT
RECEIVER
SLEEP
HDMI
1
2
3
1
2
3
4
5
6
AUDIO
■ Enjoying unprocessed playback
■ Enjoying stereo playback
(Straight decoding mode)
Use straight decoding mode when you want to playback
sound without sound field processing. You can playback
as follows in straight decoding mode.
2-channel sources such as CD
TUNER
TUNER
MEMORY
PRESET
TUNING
Stereo sound plays through the front left and right
speakers.
ENHANCER
SOUND
MUSIC
STEREO
STRAIGHT SUR. DECODE
SCENE
BD
DVD
SETUP
TV
CD
RADIO
OPTION
VOLUME
RETURN
Multi-channel playback sources such as BD/
f DVD
Plays back audio from a playback source without
applying sound field effects, using an appropriate
decoder to split the signal into multiple channels.
1
Select “2ch Stereo” from the surround field programs
when you want to playback 2-channel stereo sound
(from the front speakers only), regardless of the
playback source.
Selecting “2ch Stereo” will playback as follows for the
playback of CD and BD/DVD sources.
2-channel sources such as CD
INFO
MOVIE
■ Enjoying sound field programs
Stereo sound plays back through the front speakers.
Multi-channel sources such as BD/DVD
Playback channels other than the front channels in the
playback source are mixed with the front channels and
played back through the front speakers.
Press fSTRAIGHT to activate the straight
decoding mode.
1
Press fSTEREO repeatedly to select “2ch
Stereo.”
without surround sound speakers
This unit allows you to use virtual surround speakers to
enjoy sound field surround effects, even without any
surround speakers (Virtual CINEMA DSP mode). You
can even enjoy surround sound presence with just a
minimal configuration of the front speakers only.
This unit will switch to Virtual CINEMA DSP mode
automatically when surround speakers are
unavailable. J1
■ Enjoying sound field programs
with headphones
Even when headphones are connected, you can enjoy the
reproduction sound field presence with ease (SILENT
CINEMA mode). J2
MUTE
STEREO
VOL.
STRAIGHT
2
Sci-Fi
VOL.
L
SL
SW
C
R
SR
Previously selected program
J 1 : However, Virtual CINEMA DSP mode is not available in the
following conditions:
• When headphones are connected to this unit.
• When a “2ch Stereo” sound field program is selected.
• When straight decoding mode is selected.
VOL.
SW
2ch Stereo
R
SR
Press fSTRAIGHT again to exit straight
decoding mode.
MOVIE
f SOUND selection keys
f STRAIGHT
f STEREO
L
SL
SW
C
2
R
L
To deactivate stereo playback, press any of
the fSOUND selection keys to select a
sound field program other than “2ch
Stereo.”
MUSIC
Hall in Vienna
VOL.
L
SL
SW
C
R
SR
J 2 : However, SILENT CINEMA mode is not available in the
following conditions:
• When a “2ch Stereo” sound field program is selected.
• When straight decoding mode is selected.
En
23
PLAYBACK
Enjoying sound field programs
Sound field programs
Roleplaying Game
This sound field is suitable for role-playing and adventure games. This program adds depth
to the sound field for natural and realistic reproduction of background music, special effects
and dialog from a wide variety of scenes.
in the table indicates the sound field program for CINEMA DSP.
■ Category: MOVIE
Sound field programs optimized for viewing video sources such as movies, TV programs, and games.
Standard
Spectacle
Sci-Fi
Adventure
This program creates a sound field emphasizing the surround feeling without disturbing the
original acoustic positioning of multi-channel audio such as Dolby Digital and DTS. It has
been designed with the concept of an ideal movie theater, in which the audience is
surrounded by beautiful reverberations from the left, right and rear.
This program represents the spectacular feeling of large-scale movie productions. It
reproduces a broad theater sound field that matches cinemascope and wider-screen movies
with an excellent dynamic range providing everything from very small sound effects to
large, impressive sounds.
This program clearly reproduces the finely elaborated sound design of the latest science
fiction and special effects-featuring movies. You can enjoy a variety of cinematographically
created virtual spaces reproduced with clear separation between dialog, sound effects and
background music.
This program is ideal for precisely reproducing the sound design of action and adventure
movies. The sound field restrains reverberations but puts emphasis on reproducing a
powerful space expanded widely to the left and right. The reproduced depth is also
restrained relatively to ensure the separation between audio channels and the clarity of the
sound.
Drama
This sound field features stable reverberations that match a wide range of movie genres from
serious dramas to musicals and comedies. The reverberations are modest but offer an
optimum 3D feeling, reproducing effects tones and background music softly but cubically
around clear words and center positioning in a way that does not fatigue the listener even
after long hours of viewing.
Mono Movie
This program is provided for reproducing monaural video sources such as a classic movie in
an atmosphere of a good old movie theater. The program produces the optimum expansion
and reverberation to the original audio to create a comfortable space with a certain sound
depth.
Sports
This program allows the listeners to enjoy stereo sport broadcasts and studio variety
programs with enriched live feeling. In sports broadcasts, the voices of the commentator and
sportscaster are positioned clearly at the center while the atmosphere of the stadium expands
in an optimal space to offer the listeners a feeling of presence in the stadium.
Action Game
This sound field is suitable for action games such as car racing, fighting games and FPS
games. The reality of, and emphasis on, various effects makes the player feel like they are
right in the middle of the action, allowing for greater concentration.
■ Category: MUSIC
This sound field is suitable when listening to music sources such as CDs.
Hall in Munich
This sound field simulates a concert hall with approximately 2500 seats in Munich, using
stylish wood for the interior finishing as normal standards for European concert halls. Fine,
beautiful reverberations spread richly, creating a calming atmosphere. The listener’s virtual
seat is at the center left of the arena.
Hall in Vienna
This is an approximately 1700-seat, middle-sized concert hall with a shoebox shape that is
traditional in Vienna. Pillars and ornate carvings create extremely complex reflections from
all around the audience, producing a very full, rich sound.
Chamber
This program creates a relatively wide space with a high ceiling like an audience hall in a
palace. It offers pleasant reverberations that are suitable for courtly music and chamber
music.
Cellar Club
This program simulates a live house with a low ceiling and homey atmosphere. A realistic,
live sound field features powerful sound as if the listener is in a row in front of a small stage.
The Roxy Theatre
This is the sound field of a rock music live house in Los Angeles, with approximately 460
seats. The listener’s virtual seat is at the center left of the hall.
The Bottom Line
This is the sound field at stage front in The Bottom Line, a famous New York jazz club once.
The floor can seat 300 people to the left and right in a sound field offering real and vibrant
sound.
Music Video
This sound field offers an image of a concert hall for live performance of pop, rock and jazz
music. The listener can indulge oneself in a hot live space thanks to the presence sound field
that emphasizes the vividness of vocals and solo play and the beat of rhythm instruments,
and to the surround sound field that reproduces the space of a big live hall.
En
24
PLAYBACK
Enjoying sound field programs
■ Category: STEREO
Suitable for listening to stereo sources.
2ch Stereo
Use this program to mix down multi-channel sources to 2 channels. When multi-channel
signals are input, they are down mixed to 2 channels and output from the front left and right
speakers.
5ch Stereo
Use this program to output sound from all speakers. When you play back multi-channel
sources, this unit down-mixes the source to 2 channels, and then outputs the sound from all
speakers. This program creates a larger sound field and is ideal for background music at
parties, etc.
■ Category: ENHNCR (Compressed Music Enhancer)
Suitable for listening to compressed audio, such as MP3.
Straight Enhancer
Use this program to restore the original depth and dynamics of 2-channel or multi-channel
to compression audio.
5ch Enhancer
Use this program to play back compression artifacts in 5-channel stereo.
■ Category: SUR.DEC (Surround decode mode)
Select this program to playback sources with selected decoders. You can playback 2-channel sound
sources in up to 5-channels using a surround decoder.
q Pro Logic
Reproduces sound using the Dolby Pro Logic decoder. This is suitable for all kinds of sound
sources.
q PLII Movie
Reproduces sound using the Dolby Pro Logic II decoder. This is suitable for movies.
q PLII Music
Reproduces sound using the Dolby Pro Logic II decoder. This is suitable for music.
q PLII Game
Reproduces sound using the Dolby Pro Logic II decoder. This is suitable for games.
En
25
PLAYBACK
FM tuning
TRANSMIT
RECEIVER
SLEEP
HDMI
1
2
3
1
2
3
4
5
6
AUDIO
TUNER
TUNER
MEMORY
PRESET
TUNING
INFO
ENHANCER
MOVIE
SOUND
MUSIC
STEREO
STRAIGHT SUR. DECODE
When using the FM tuner, adjust the direction of the
FM antenna connected to this unit to get the best
reception.
d (Asia and General models only)
The factory pre-set FM tuner frequency steps are
d 50 kHz.
Carry out the following settings and select the frequency
steps suitable for your listening environment.
SCENE
BD
DVD
SETUP
TV
CD
RADIO
OPTION
VOLUME
RETURN
1
2
Set this unit to the standby mode.
Press A while pressing and holding
STRAIGHT on the front panel.
Release the keys when “ADVANCED SETUP” is
displayed on the front panel display.
After approximately 2 seconds, the top menu items are
displayed. J1
MUTE
A
STRAIGHT
3
Press PROGRAM h twice to display
“TUNER.”
TUNER -
4
5
FM50
Selecting a frequency for reception
(Normal tuning)
1
Press dTUNER to switch to the tuner input.
VOL.
FM87.50MHz
Press STRAIGHT a few times to select
frequency steps.
Use dTUNING H / I to set a frequency to
receive.
Switch this unit to the standby mode, and
then switch it on again.
2
The power turns on, with the settings you made
configured.
dTUNING H
Increases the frequency. Press and hold this key for
longer than a second to search automatically for a station
on a higher frequency than the current one. J2
The FM tuner of this unit provides the following two
modes for tuning.
Normal tuning
You can tune in to a desired FM station by searching or
specifying its frequency.
dTUNING I
Decreases the frequency. Press and hold this key for
longer than a second to search automatically for a station
on a lower frequency than the current one. J2
Preset tuning (☞p. 27)
INFO
MEMORY
PRESET
TUNING
FM
SCENE
BD
DVD
PHONES
d TUNER
d TUNING H / I
INPUT
TONE CONTROL
TV
CD
PROGRAM
RADIO
STRAIGHT
SILENT CINEMA
You can preset the frequencies of FM stations by
registering them to specific numbers, and later just select
those numbers to tune in.
Lights up when receiving
a broadcast from a station
Lights up when receiving
a stereo broadcast
VOL.
STEREO
TUNED
FM98.50MHz
L
SL
SW
C
R
SR
PROGRAM l / h
REMOTEID-ID1
J 1 : For detailed information on the advanced setup menu see
“Extended functionality that can be configured as needed
(Advanced Setup menu)” (☞p. 44).
J 2 : When searching for a station, release the key once the search has
started.
En
26
PLAYBACK
FM tuning
TRANSMIT
■ When signal reception is poor
RECEIVER
SLEEP
HDMI
1
2
1
2
3
4
5
6
When you are receiving an FM broadcast and cannot
obtain a stable stereo broadcast, you can force this unit
to receive in a monaural mode by pressing FM MODE
on front panel or following steps.
3
AUDIO
d
TUNER
TUNER
MEMORY
PRESET
TUNING
INFO
d
ENHANCER
MOVIE
SOUND
MUSIC
STEREO
STRAIGHT SUR. DECODE
SCENE
BD
DVD
TV
SETUP
CD
RADIO
OPTION
ENTER
l
VOLUME
1
Press dTUNER to switch to the tuner input.
2
3
Press lOPTION to display the Option
menu. J1
i
Use iCursor B / C to select “FM Mode.”
OPTION
FMMode
RETURN
VOL.
STEREO
TUNED
MUTE
4
Press iENTER and use the iCursor D / E
to select “Mono.”
9850
VOL.
TUNED
FMMode:Mono
5
d TUNER
d PRESET F / G
i Cursor B / C / D / E
i ENTER
i RETURN
l OPTION
When setting is completed, press
lOPTION to close the Option menu.
To return this unit to its original settings, use the same
procedure to return the settings to “Stereo.”
Registering and recalling a
frequency (Preset tuning)
4
You can register up to 40 FM stations as preset stations.
There are two methods of presetting stations, “Auto
Preset” and “Manual Preset.” Use one of these methods
to register stations.
■ Presetting FM stations
automatically (Auto Preset)
The tuner detects FM stations with strong signals and
registers up to 40 automatically.
1
2
3
Press dTUNER to switch to the tuner input.
Press iENTER, then press dPRESET F /
G or iCursor B / C to choose the preset
number from which to start the Auto Preset
function.
Auto Preset will begin approximately 5 seconds after
you select a preset number.
If you do not select a preset number, Auto Preset will
begin approximately 5 seconds after “READY” is
displayed.
Selecting a preset number
Status
Frequency
READY
VOL.
01:FM87.50MHz
Press lOPTION to display the Option
menu. J1
Use iCursor B / C to select “Auto Preset.”
OPTION
Auto Preset
L
SL
SW
C
R
SR
Preset number
To cancel registration, press iRETURN.
During Auto Preset
VOL.
Search
Preset for stations
SEARCH
MEMORY
When Auto Preset is complete
FINISH
ENHANCER
iPod CHARGE
STEREO
TUNED
Auto Preset
SLEEP
VOL.
MUTE
L
SL
SW
C
R
SR
The Option menu closes automatically when presetting
is complete. J2
J 1 : See the section on “Configuring the settings specific for each
input source (Option menu)” for details on the Option menu
(☞p. 30).
J 2 : The preset with the lowest preset number will be selected
automatically immediately after presetting.
En
27
PLAYBACK
FM tuning
TRANSMIT
■ Registering stations manually
RECEIVER
SLEEP
HDMI
1
2
3
1
2
3
4
5
6
Select stations by hand and register them as presets
individually.
AUDIO
1
TUNER
TUNER
MEMORY
PRESET
TUNING
INFO
ENHANCER
MOVIE
SOUND
MUSIC
STEREO
STRAIGHT SUR. DECODE
SCENE
BD
DVD
SETUP
TV
CD
RADIO
OPTION
VOLUME
RETURN
MUTE
d
2
Tune in to the station you wish to register,
referring to “Selecting a frequency for
reception (Normal tuning)” (☞p. 26).
Press dMEMORY once, to display “Manual Preset” on
the front panel display. After a small wait, the preset
number that the station has been registered to will
appear.
Press dMEMORY for 2 seconds or longer.
The station will be registered automatically to the lowest
i open preset number (or the next number after the one
registered most recently).
To select a registered station, press dPRESET
F / G to select the preset number of the station.
The newly registered frequency
VOL.
01:Empty
■ Registering to a preset number to which no
station is registered
You can call preset stations registered by automatic
station preset or manual station preset. J1
Preset number
9850
Use one of the following methods to
register the station you are currently
receiving.
MEMORY
■ Recalling a preset station
■ Designating a preset number for
registration
(Manual Preset)
Blinks
STEREO
TUNED
L
SL
SW
C
R
SR
Empty, or the frequency registered
most previously.
Press dPRESET F / G to select the preset to register
the station to, and then press dMEMORY to register.
To cancel registration, press iRETURN or do not
operate the remote control for about 30 seconds.
VOL.
STEREO
TUNED
01:FM98.50MHz
L
SL
SW
C
R
SR
Registered frequencies
d MEMORY
d PRESET F / G
i RETURN
J 1 : Preset numbers to which no stations are registered will be
skipped. “No Presets” is displayed when there are no stations are
registered.
En
28
PLAYBACK
FM tuning
TRANSMIT
HDMI
1
2
3
1
2
3
4
5
6
AUDIO
d
TUNER
TUNER
MEMORY
PRESET
TUNING
INFO
ENHANCER
MOVIE
SOUND
MUSIC
■ Combining the video signals and
Clearing preset stations
RECEIVER
SLEEP
STEREO
STRAIGHT SUR. DECODE
1
2
3
radio audio signals
Press dTUNER to switch to the tuner input.
Press lOPTION to display the Option
menu. J1
Select the video signal to be output from the video
output jack on this unit when TUNER is selected as the
input source.
1
2
Use iCursor B / C to display “Clear
Preset” and press iENTER.
Selectable video source:
HDMI1-3
Video signals input from one of the
HDMI1 to 3 are output from the HDMI
output jack on this unit.
Off
Video signals are not output when
TUNER is selected as the input source.
Press dTUNER to switch to the tuner input.
Press lOPTION to display the Option
menu. J1
5
Press lOPTION to finish this operation.
SCENE
BD
DVD
TV
SETUP
CD
ENTER
The number of the preset to be cleared
RADIO
OPTION
OPTION
Volume Trim
l
VOLUME
CLEAR
i
VOL.
STEREO
TUNED
01:FM98.50MHz
RETURN
L
SL
SW
C
R
SR
MUTE
Blinks
3
Use iCursor B / C to select the preset
number you want to clear, and press
iENTER to clear it.
Repeat this operation to clear the registration of
multiple numbers.
d TUNER
i Cursor B / C / D / E
i ENTER
i RETURN
l OPTION
Use iCursor B / C to display “Video Out”
and press iENTER.
Registered frequencies
OPTION
Press iRETURN to cancel the operation.
4
VOL.
VOL.
Video Out
4
Use iCursor D / E to select the video
source you want to watch, and press
iENTER.
TUNER
VOL.
Video;;;;HDMI1
5
Press lOPTION to finish this operation.
J 1 : See the section on “Configuring the settings specific for each
input source (Option menu)” for details on the Option menu
(☞p. 30).
En
29
SETUP
TRANSMIT
Configuring the settings specific for each input source (Option menu)
RECEIVER
SLEEP
HDMI
1
2
3
1
2
3
4
5
6
This receiver has a unique option menu specific for each type of input source, such as volume trim for compatible input sources, audio/video data display for signals from
c external devices, and other frequently used menu items.
AUDIO
Option menu display and setup
3
TUNER
TUNER
MEMORY
PRESET
TUNING
INFO
ENHANCER
MOVIE
SOUND
MUSIC
1
Use the cInput selector on the remote
control to select the Option menu you wish
to display.
2
Press lOPTION.
STEREO
STRAIGHT SUR. DECODE
SCENE
BD
DVD
TV
SETUP
CD
RADIO
OPTION
ENTER
l
VOLUME
i
The Option menu appears for the desired input source.
Option menu
RETURN
MUTE
OPTION
VolumeTrim
SW
C
5
The displayed Option menu items differ depending on
the input source.
For details, read the following Option menu items
section.
4
To close the Option menu, press lOPTION.
For a few seconds after closing the Option menu, the
remote control keys may not function. If this occurs,
reselect the input source.
Select the desired menu item (or enable a
function) using iCursor B / C / D / E and
iENTER.
Parameters of the selected item are displayed. The
parameters you can set differ depending on the menu
items.
VOL.
L
SL
Select the desired control/setup item using
iCursor B / C and press iENTER.
R
SR
• You can also use iRETURN to return to the previous
screen or close the Option menu.
• Certain selected menu items may automatically close
the Option menu when their functions are enabled.
Option menu items
The following items are provided for each input source. “✓” indicates the available menu for each input source.
c Input selector
i Cursor B / C / D / E
i ENTER
i RETURN
l OPTION
Volume Trim
Audio In
Signal Info
HDMI 1-3
✓
✓
✓
AUDIO 1-4
✓
AUDIO 5-6
✓
TUNER
✓
FM Mode
Auto Preset
Clear Preset
Video Out
✓
✓
✓
✓
✓
En
30
SETUP
Configuring the settings specific for each input source (Option menu)
■ Adjusting volume between input sources
Set as follows according on the desired combination of audio input
jacks.
Volume Trim
Input source:
Settings method
Optical digital audio
input
Select AUDIO 1 or AUDIO 4. Connect the external
component audio cable to the optical jack for the
selected input.
Coaxial digital audio
input
Select AUDIO 2 or AUDIO 3. Connect the external
component audio cable to the coaxial jack for the
selected input.
Analog audio input
Select AUDIO 5 or AUDIO 6. Connect the external
component audio cable to the audio jack for the
selected input.
All
Reduces any change in volume when switching between input
sources by correcting volume differences in each input source. You
can adjust this parameter for each input source.
Adjustable range
-6.0 dB to 0.0 dB to +6.0 dB
Default setting
0.0 dB
Adjustment
increments
0.5 dB steps
■ Combining HDMI input source video and
audio
Audio In
Input source:
Audio inputs
HDMI 1-3
Combines video from HDMI input sources with analog/digital
audio inputs in situations such as:
– an external device is connected with an HDMI cable but cannot
transmit audio through HDMI
Inputs that change the audio source
HDMI1
• For details of settings, refer to “Receiving audio from other input
sources” (☞p. 15).
• To return audio inputs to their previous settings, display this item
again, and select the original input jack.
■ Displaying information on audio/video
signals
Signal Info
Input source:
VOL.
Audio;;;AUDIO1
L
SL
SW
C
R
SR
Assignable audio input jacks
To change assignments, select an input source (HDMI 1-3) as the
video input first, and then select audio input jacks in this menu.
HDMI 1-3, AUDIO 1-4 J1
Displays information on digital audio and video signals on the
front panel display. You can display the signal information by
pressing iENTER on the menu item and using iCursor B / C.
Audio information
FORMAT
Format of audio signals.
CHAN
The number of input signal channels (front/surround/
LFE).
For example, if input signal channels are 3 front
channels, 2 surrounds and LFE, “3/2/0.1” is
displayed.
SAMPL
The sampling frequency of analog-to-digital
conversion.
B RATE
The bit rate of input signal per second.
Video information
V IN
Format and resolution of video input signal.
V OUT
Format and resolution of video output signal.
V.MSG
(appears only
when an error
has occurred)
Error messages about HDMI signals and components.
Error message
HDCP Error
HDCP authentication failed.
Device Over The number of connected HDMI
components is over the limit.
• “No Signal” is displayed when no signals are being received, and
“---” is displayed if this unit cannot recognize the incoming
signal.
• The bit rate may vary during playback.
Menu item
FORMAT
VOL.
DolbyD
L
SL
SW
C
R
SR
Information
J 1 : AUDIO 5-6 are also available when the “Audio Return Channel” function is on,
and the source is used for the TV audio input (TVAudio).
En
31
SETUP
Configuring the settings specific for each input source (Option menu)
■ Changing FM mode (Stereo/Monaural)
FM Mode
Input source:
TUNER
Sets this unit to automatically match FM broadcast frequencies in
stereo, or to convert the frequency to monaural (☞p. 27).
■ Automatically presetting FM radio
stations
Auto Preset
Input source:
TUNER
Automatically detects radio stations in the FM frequency and
registers them as preset stations (☞p. 27).
■ Clearing preset FM stations
Clear Preset
Input source:
TUNER
Clears the preset stations (☞p. 29).
■ Combining the video signals and radio
audio signals
Video Out
Input source:
TUNER
Select the type of video signals to be output from the video output
jack on this unit when TUNER is selected as the input source
(☞p. 29).
En
32
SETUP
Setting various functions (Setup menu)
TRANSMIT
RECEIVER
SLEEP
HDMI
1
2
3
1
2
3
4
5
6
You can configure various function settings of this unit using the Setup menu.
Setup menu display and settings
AUDIO
TUNER
1
TUNER
MEMORY
PRESET
TUNING
3
Press hSETUP on the remote control.
HDMI
INFO
SETUP
ENHANCER
MOVIE
SOUND
MUSIC
STEREO
STRAIGHT SUR. DECODE
BD
DVD
TV
SETUP
CD
RADIO
h
OPTION
ENTER
VOLUME
i
2
L
SL
SW
C
R
SR
Use the iCursor B / C to select the desired
menu and press iENTER.
Setup menu categories
RETURN
MUTE
h SETUP
i Cursor B / C / D / E
i ENTER
i RETURN
Speaker Setup
Manages settings for speakers.
Sound Setup
Manages settings for audio output.
HDMI Setup
Manages settings for HDMI, such as
HDMI Control functions.
Func. Setup
Manages settings to make receiver
operation easier, such as input source
labeling and auto-standby functions.
Memory Guard
Protects settings against accidental
alteration.
Lipsync
VOL.
SW
C
SW
C
R
SR
Setup menu items
Setup menu
Speaker Setup
Config
Subwoofer
Front
Center
Sur. LR
Crossover
SWFR Phase
Extra Bass
Level
Distance
Equalizer
Test Tone
Sound Setup
Lipsync
Adaptive DRC
D.Range
Max Volume
Init.Volume
HDMI Setup
Control
TVAudio
ARC
Audio
(speakers)
(unit and speakers)
(speakers and frequency
bands)
R
SR
Ex: HDMI Setup menu
4
5
6
Sets parameters for sound field programs.
L
SL
L
SL
When multiple items appear, use iCursor
B / C to select the desired item.
Press iCursor D / E to change the setting.
You can change other items by repeating step 4 and 5.
You can also use iRETURN to return to the
previous screen.
DSP Parameter
SOUND
VOL.
Audio;;;;;;Amp
VOL.
SpeakerSetup
SCENE
Use iCursor B / C to navigate the
submenus to find the desired setting and
press iENTER.
Press hSETUP to exit the Setup menu.
For a few seconds after closing the Setup menu, the
remote control keys may not function. If this occurs,
reselect the input source.
HDMI Auto
Auto
Manual
Func. Setup
Input Rename
AutoPowerDown
Dimmer
DSP Parameter
Memory Guard
Ex: Sound Setup menu
En
33
SETUP
Setting various functions (Setup menu)
■ Manual speaker setup
Manages settings for speakers
Config
SETUP
Adjusts the output characteristics of the speakers based on
manually set parameters.
VOL.
SpeakerSetup
L
SL
SW
C
Manually manages speaker configuration, such as
speaker size (sound production capacity), and bass
audio processing.
Level
Manually adjusts the volume of each speaker.
Distance
Manually adjusts the output of each speaker based on
distance to the listening point.
Equalizer
Test Tone
Small (Default)
Select this for small speakers. The subwoofer will
produce front channel low-frequency
components. J3
Large
Select this for large speakers. The front speakers will
produce all of the front channel frequency
components.
R
SR
Speaker Setup submenu
Config
Front
Selects the size (sound reproduction capacity) of the front
speakers. J2
■ The case of general speakers
In the Config submenu, you can select the speaker size
characteristic (Large or Small). Select the size (sound
reproduction capacity) that matches your speakers.
Center
Selects the size of the center speakers.
Woofer diameter
• 16 cm or larger → Large
• 16 cm or smaller → Small
Selects an equalizer to adjust speaker output
characteristics.
None
Select this when there is no center speaker. The front
speakers will produce center channel audio.
Small (Default)
Select this when a small center speaker is connected.
Large
Select this when a large center speaker is connected.
Generates test tones.
When speaker size is set to “Small,” low-frequency components
of the speakers that you configured are produced from the
subwoofer (or from the front speakers if there is no subwoofer).
Sur. LR
Selects the size of the surround speakers.
None
Select this when no surround speakers are connected.
The front speakers will produce surround channel
audio signals.
Small (Default)
Select this when the surround speakers are small.
Large
Select this when the surround speakers are large.
Subwoofer
Confirms the subwoofer.
Yes (Default)
None
J 1 : Enabling the “Extra Bass” setting allows both the subwoofer and the front
speakers to produce bass audio.
J 2 : When “Subwoofer” is set to “None,” you can only choose “Large.” If the front
speaker setting is “Small” and you change “Subwoofer” to “None,” it will
automatically change to “Large.”
Select this when you have a subwoofer connected.
During playback, the subwoofer will produce audio
from the LFE (low-frequency effect) channel and bass
audio from other channels. J1
Select this when you do not have a subwoofer
connected. The front speakers will produce audio
from the LFE (low-frequency effect) channel and bass
frequency audio from other channels.
J 3 : Enabling the “Crossover” setting allows you to set the frequency components
of audio signals transmitted from the front speakers to the subwoofer.
En
34
SETUP
Setting various functions (Setup menu)
Crossover
Sets the lower limit of low-frequency component output from
speakers set to “Small.”
Audio with a frequency below that limit will be produced from the
subwoofer or the front speakers. J1
■ Controlling the volume of each speaker
Level
Distance
Separately adjusts the volume of each speaker. Use iCursor B /
C to select the desired speaker and adjust the volume with
iCursor D / E.
40Hz
110Hz
60Hz
120Hz
FL
Front speaker L
80Hz
160Hz (Default)
FR
Front speaker R
90Hz
200Hz
C
Center speaker
SL
Surround speaker L
SR
Surround speaker R
SWFR
Subwoofer
100Hz
SWFR Phase
Sets the phase of the subwoofer if the bass audio is lacking or
unclear.
NRM (Default)
Does not change the subwoofer phase.
REV
Reverses the subwoofer phase.
Extra Bass
Allows the front channel low-frequency components to be
produced exclusively by the subwoofer, or by both the subwoofer
and the front speakers.
Off (Default)
On
Depending on the size of the front speakers, either the
front speakers or the subwoofer produce the front
channel low-frequency components.
■ Manually setting speaker distance
Adjusts the timing at which the speakers produce audio so that
sounds from the speakers reach the listening position at the same
time.
Selecting adjustment units
Use iCursor B / C to display “Unit,” and then use iCursor D
/ E to choose the units of length (meters or feet).
Setting distances for each speaker
Use iCursor B / C to display the speaker you want to configure,
and then use iCursor D / E to set the distance from the speaker
to your listening position.
Unit
Selects the distance unit (meters or feet).
Adjustable range
-10.0 dB to +10.0 dB
Front L
Front speaker L
Default setting
0 dB (FL / FR / SWFR)
-1.0 dB (C / SL / SR)
Front R
Front speaker R
Center
Center speaker
0.5 dB
Sur. L
Surround speaker L
Sur. R
Surround speaker R
SWFR
Subwoofer
Adjustable range
0.30 m to 24.00 m (1.0 ft to 80.0 ft)
Default setting
3.00 m (10.0 ft) (Front L/Front R/SWFR)
2.60 m (8.5 ft) (Center)
2.40 m (8.0 ft) (Sur. L/Sur. R)
Adjustment
increments
0.10 m (0.5 ft)
Adjustment
increments
The subwoofer and the front speakers produce the
front channel low-frequency components.
When the “Subwoofer” is set to “None,” the “Extra Bass”
setting is disabled.
J 1 : If your subwoofer has a volume control or a crossover frequency control, set
the crossover frequency to maximum and the volume to half (or slightly less).
En
35
SETUP
Setting various functions (Setup menu)
■ Adjusting sound quality with the equalizer
Equalizer
3
Adjusts sound quality and tune with a graphic equalizer.
Raising volume: Press iCursor E.
Lowering volume: Press iCursor D.
EQ Select
Turns the graphic equalizer on or off. By selecting GEQ and
pressing iENTER, you can adjust the characteristics of the
graphic equalizer.
GEQ (Default)
Uses the graphic equalizer to adjust sound quality.
Off
Does not activate the equalizer.
■ Adjusting the graphic equalizer
1
2
When “EQ Select” is displayed, use iCursor D / E
to select “GEQ” and press iENTER.
Check that “Channel” appears and use iCursor D /
E to select the speaker for which you want to adjust
the equalizer.
GEQ
GEQ
Channel;FRNT L
SW
C
VOL.
63Hz
Frequency band
L
SL
SW
C
■ Generating test tones
Test Tone
Turns the test tone generator on or off.
Off (Default)
Does not generate test tones.
On
Generates test tones. While “On” is selected, test
tones are produced constantly.
R
SR
Setting the volume level for
the selected frequency
Frequency
range
63 Hz/160 Hz/400 Hz/1 kHz/2.5 kHz/6.3 kHz/
16 kHz
Adjustable
range
-6.0 dB to +6.0 dB
Default setting
0 dB
Adjustment
increments
0.5 dB
VOL.
L
SL
Press iCursor C repeatedly to select the frequency
you want to adjust, then use iCursor D / E to adjust
the volume.
You can use the test tone in a variety of circumstances. For
example, you can adjust the volume balance settings for each
speaker, or whenever you adjust the settings on the internal
graphic equalizer, you can listen to the actual effect while
operating this unit. Turn the test tone off when you have finished
making adjustments.
You can use iCursor B / C to select another frequency or
return to step 2. Repeat steps 2-3 to adjust the tone to your
liking.
R
SR
The speaker you are adjusting
4
When you have finished making adjustments, press
hSETUP to close the Setup menu.
En
36
SETUP
Setting various functions (Setup menu)
SoundSetup
Lipsync
Adjusts the delay between audio and video output (Lipsync
function).
VOL.
L
SL
SW
C
R
SR
HDMI Auto
When connecting to a TV via HDMI, automatically adjusts output
timing if the TV supports an automatic lipsync function.
Sound Setup submenu
Off
Lipsync
Adjusts the delay between video and audio output.
Adaptive DRC
Auto-adjusting the sound level to make even low
volumes more audible.
D.Range
Selects the dynamic range adjustment method for
digital audio playback.
Max Volume
Sets the maximum volume for this receiver.
Init.Volume
Sets the initial volume for when this receiver is turned
on.
On (Default)
Select this when the connected TV does not support
the automatic lipsync function or you do not wish to
use the automatic lipsync function. Set the correction
time in “Manual.”
Select this when the TV supports the automatic
lipsync function. Fine-adjust the correction time in
“Auto.”
Auto
Fine-adjust the audio output timing by entering the correction time
provided when “HDMI Auto” is set to “On.”
Adjustable range
0 ms to 240 ms
Adjustment
increments
1 ms
■ Auto-adjusting the sound level to make
even low volumes more audible
Adaptive DRC
Adjusts the dynamic range in conjunction with the volume level
(from minimum to maximum). When you play audio at night or at
low volumes, it is a good idea to set parameter to “On.” J1
Off (Default)
Does not adjust the dynamic range automatically.
On
Adjusts the dynamic range automatically.
When the auto function is enabled, it adjusts the dynamic range as
follows.
On
Off
Input Level
Volume: low
Output Level
SETUP
■ Synchronizing audio/video output
Output Level
Setting the audio output function of this
unit
On
Off
Input Level
Volume: high
Manual
Manually adjusts the correction time. Select this when the TV does
not support the automatic lipsync function or “HDMI Auto” is set
to “Off.”
Adjustable range
0 ms to 240 ms
Adjustment
increments
1 ms
Default setting
0 ms
J 1 : The Adaptive DRC setting is also effective when you use headphones.
En
37
SETUP
Setting various functions (Setup menu)
■ Auto-adjusting Dolby Digital and DTS
dynamic range
D.Range
Selects the dynamic range adjustment method for audio bitstream
(Dolby Digital and DTS) playback.
Min
Sets the dynamic range suitable for low volume or a
quiet environment, such as at night, for bitstream
signals.
Std
Adjusts the dynamic range for optimum volume for
regular home use.
Max (Default)
Produces audio without adjusting the dynamic range.
■ Setting the maximum volume
Max Volume
■ Setting the startup volume
Setting HDMI functions
Init.Volume
Sets the initial volume for when this receiver is turned on. When
this parameter is set to “Off,” the volume is set at the level when the
receiver last entered standby mode. J1
Adjustable range
Off, Mute, -80 dB to +16.5 dB
Default setting
Off
Adjustment
increments
0.5 dB
SETUP
VOL.
HDMISetup
L
SL
SW
C
R
SR
HDMI Setup submenu
Control
Turns the HDMI Control on or off.
TVAudio J2
Chooses automatically selected audio input in
conjunction with TV operation when the HDMI
Control is turned on.
ARC J2
Transmits audio/video output to the TV and audio
input from the TV through a single HDMI cable.
Audio J2
Selects the audio output device connected to this
unit via HDMI jacks.
Sets a maximum volume level so that the audio is not played too
loudly. The default setting of +16.5 dB produces the highest
volume.
Adjustable range
-30.0 dB to +15.0 dB / +16.5 dB (Maximum volume)
Default setting
+16.5 dB
Adjustment
increments
5.0 dB
J 1 : When you set the “Max Volume” at a lower level than “Init.Volume,” the “Max
Volume” setting has priority.
J 2 : When “Control” is set to On, “TVAudio” and “ARC” appear. When “Control”
is set to Off, “Audio” appears.
En
38
SETUP
Setting various functions (Setup menu)
■ Receiver operation via TV (HDMI Control)
Control
Set the HDMI Control function to “On” to operate devices
connected via HDMI. If the TV or other external components
support HDMI Control (ex. Panasonic VIERA Link), you can use
the remote controls of those devices to operate some of this unit’s
functions, and to synchronize this unit with the operation of those
devices.
Please refer to “Switching the input source on this unit
automatically when listening to TV audio” (☞p. 47) for
instructions.
Off (Default)
Sets HDMI Control to “Off.”
On
Sets HDMI Control to “On.”
If this unit is connected to HDMI devices that do not support the
HDMI Control function, these functions will not operate.
■ Selecting an input source to assign audio
input for the TV
TVAudio
Select the input source that matches operations carried out on the
TV while the HDMI Control function is on.
When using a TV that supports Audio Return Channel function and
the function is enabled, the audio input for the TV is assigned to
the input source selected here. J1
AUDIO1 to
AUDIO6
Assigns any of the AUDIO 1-6 input source for the
audio input from the TV.
Default setting
AUDIO 4
• “TVAudio” is only displayed with the HDMI Control function
(Control) is set to “On.”
• Please refer to “Using the HDMI Control function” (☞p. 46) for
setting instructions.
• For details on inputting the audio signal from the TV, refer to
“Listening to TV audio” (☞p. 13).
■ Listening to TV audio via single HDMI
■ Changing the output destination of HDMI
input audio signals
Audio
Choose whether to playback audio from an external component
such as a BD/DVD player connected via HDMI through this unit or
through a TV.
Amp (Default)
Outputs audio through this unit only. When this
setting is selected, the external component outputs an
audio format compatible with this unit.
TV
Outputs audio through a TV only. When this setting is
selected, the external component outputs an audio
format compatible with the TV. J2
Amp+TV
Outputs audio from the TV and this unit. When this
setting is selected, the external component outputs an
audio format compatible with TV.
cable (Audio Return Channel)
ARC
You can enable or disable the Audio Return Channel function.
When using a TV that supports Audio Return Channel function and
the function is enabled, the TV’s audio output is transmit to this
unit via an HDMI cable.
The TV audio input to this unit is regarded as the input source
selected in “TVAudio.” J1
By means of this function, you do not need to connect the TV’s
audio output (digital audio output or analog audio output) to the
unit.
Off
Sets the Audio Return Channel to “Off.”
On (Default)
Sets the Audio Return Channel to “On.”
“Audio” is only displayed with the HDMI Control function
(Control) is set to “Off.”
When the TV audio is input to the unit using Audio Return
Channel, “TV” is displayed on the front panel display.
TV
AUDIO4
VOL.
L
SL
SW
C
R
SR
• “ARC” is only displayed with the HDMI Control function
(Control) is set to “On.”
• Please refer to “Single HDMI cable input to TV audio with Audio
Return Channel function” (☞p. 48) for setting instructions.
J 1 : While the Audio Return Channel function is on, the jack selected for the input
source cannot be used.
J 2 : When “TV” is selected, the speakers of this unit do not output sound.
En
39
SETUP
Setting various functions (Setup menu)
TRANSMIT
Making the receiver easier to use
RECEIVER
SLEEP
HDMI
1
2
3
1
2
3
4
5
6
SETUP
AUDIO
3
Use iCursor D / E to select a new name
from the following templates.
3
Press iENTER.
HDMI1
VOL.
Func.Setup
L
SL
SW
C
R
SR
Blu-ray
Satellite
DVD
VCR
SetTopBox
Tape
Game
MD
HDMI1
TUNER
TUNER
Func. Setup submenu
MEMORY
PRESET
TUNING
INFO
ENHANCER
MOVIE
SOUND
MUSIC
BD
DVD
STRAIGHT SUR. DECODE
TV
CD
Changes the input source names.
TV
PC
AutoPowerDown
Goes into standby mode.
DVR
iPod
RADIO
h
Dimmer
Sets the Brightness of the front panel
display.
CD
HD DVD
CD-R
(blank)
OPTION
ENTER
VOLUME
RETURN
i
4
HDMI1
MUTE
Changes the input source names to be shown on the front
panel display.
You can change an input source name by choosing from
a list of templates, or make one of your own.
■ Selecting a template
1
HDMI1
VOL.
L
SL
SW
C
SW
C
Select the input source that you want to
rename using iCursor B / C.
R
SR
1
2
Select “Input Rename” from the Setup
menu and press iENTER.
A to Z, a to z
0 to 9
Symbols (#, *, -, +, etc.)
Space
R
SR
Confirm the new display name by pressing
iRETURN. Press hSETUP to exit the
Setup menu.
■ Entering an original name
L
SL
R
SR
Use iCursor B / C to select the characters
you wish to change, and use iCursor D / E
to enter those characters.
•
•
•
•
5
Repeat step 4 until you have entered the
new input source name.
HDMI1
VOL.
YAMAHABD
To cancel a name change, select the original name and
then press iRETURN to exit renaming.
VOL.
Renaming the input source
2
4
Select “Input Rename” from the Setup
menu and press iENTER.
HDMI1
h SETUP
i Cursor B / C / D / E
i ENTER
i RETURN
Blu-ray
SW
C
The following characters are available for input source.
■ Changing input source names
Input Rename
L
SL
Cursor
STEREO
SCENE
SETUP
Input Rename
VOL.
6
L
SL
SW
C
R
SR
Confirm the new display name by pressing
iENTER. Press hSETUP to exit the Setup
menu.
To cancel a name change, press iRETURN.
Select the input source that you want to
rename using iCursor B / C.
En
40
SETUP
Setting various functions (Setup menu)
■ Goes enter standby mode automatically
when you leave it without operating
Setting sound field program parameters
You can set the parameters for the sound field programs (☞p. 42).
AutoPowerDown
If you do not operate this unit or use the remote control for an
extended period of time, it will automatically go into standby mode
(Auto Power Down function). When you wish to activate this
function, set the amount of time to pass before this unit will enter
standby.
Off
Auto Power Down function is disabled.
4hours
Goes into standby mode, when you have not operated
this unit for four hours.
8hours
Goes into standby mode, when you have not operated
this unit for eight hours.
12hours
Goes into standby mode, when you have not operated
this unit for twelve hours.
SETUP
VOL.
DSPParameter
L
SL
SW
C
R
SR
Prohibiting setting changes
SETUP
Memory Guard
VOL.
L
SL
SW
C
R
SR
Prohibits setting changes to prevent careless changes being made
to the settings on Setup menu.
Default
Off (Default)
Settings are not protected.
U.K. and Europe models: “8hours”
Other models: “Off”
On
Prohibits changes to the settings on Setup menu until
it is returned to “Off.”
While set to “On,” the unit displays “Memory
Guard!” when an attempt is made to change the
settings.
This unit starts a countdown of 30 seconds before entering the
standby mode. Pressing any key of the remote control during the
countdown cancels entering the standby mode and reset the
timer.
■ Setting the brightness of the front panel
display
Dimmer
Sets the brightness of the front panel display. Lowering the setting
dims the display.
Adjustable range
-4 to 0
Default setting
0
En
41
SETUP
Setting sound field program parameters
TRANSMIT
RECEIVER
SLEEP
HDMI
1
2
3
1
2
3
4
5
6
Although the sound field programs would satisfy you as they are with the default parameters, you can arrange the effect by setting the sound field elements (parameters).
To adjust the sound effects suitable for acoustical conditions of audio/video sources or rooms, perform the following operations.
AUDIO
Setting sound field parameters
4
TUNER
TUNER
1
2
MEMORY
PRESET
TUNING
INFO
ENHANCER
MOVIE
SOUND
MUSIC
STEREO
STRAIGHT SUR. DECODE
SCENE
BD
DVD
TV
SETUP
CD
RADIO
SETUP
VOLUME
3
SW
C
R
SR
Use iCursor D / E to choose the sound
field program you want to edit.
DSPPRM
Sci-Fi
Sound field program to be edited
h SETUP
i Cursor B / C / D / E
i ENTER
Sound field parameter
L
SL
VOL.
L
SL
SW
C
R
SR
DSP Level
Change the effect level (level of the sound field effect to
be added). You can adjust the level of the sound field
effect while checking the sound effect.
VOL.
DSPLevel;;0dB
VOL.
DSPParameter
i
RETURN
MUTE
DSPPRM
Use iCursor B / C to select “DSP
Parameter” and press iENTER.
h
OPTION
ENTER
Press hSETUP to display the Setup menu.
■ CINEMA DSP parameters
Press iCursor B / C to select the
parameter that you want to change, and
press iCursor D / E to change the
parameter.
L
SL
SW
C
-6 dB to 0 dB to +3 dB
Default setting
0 dB
Choices
When there are multiple parameters in the sound field
program you are configuring, repeat step 4 as
necessary to change other parameters.
5
Adjustable range
R
SR
Once you have completed editing, press
hSETUP to close the Setup menu.
Adjust “DSP Level” as follows:
• The effect sound is too soft.
• There are no differences between effects of the sound
field programs.
→ Increase the effect level.
• The sound is dull.
• The sound field effect is added too much.
→ Reduce the effect level.
■ To initialize the sound field parameters
To set the parameters of the sound field program back
to default, press iCursor C repeatedly during
editing to select “Initialize” and press iCursor E.
When “Press Again >” is displayed, press iCursor
E again to initialize.
DSPPRM
Initialize
VOL.
L
SL
SW
C
R
SR
To cancel operations, press iCursor D when “Press
Again” appears and return to the original display.
En
42
SETUP
Setting sound field program parameters
■ Parameters usable in certain sound field
programs
EFCT LVL
2ch Stereo only
Adjusts the effect level of the Compressed Music Enhancer mode.
Direct
Automatically bypasses the DSP circuit and tone control circuit
depending on the condition of tone control etc., when an analog
sound source is played back. You can enjoy a higher quality sound.
Auto (Default)
Off
Straight Enhancer/5ch Enhancer only
Outputs sound by bypassing the DSP circuit and tone
control circuit when both tone controls of “Bass” and
“Treble” are set to 0dB.
Does not bypass the DSP circuit and tone control
circuit.
5ch Stereo only
CT Level
Adjusts the center channel volume. J1
Adjustable range
0 to 100%
Default setting
100%
SL Level
Adjusts the volume of the surround L channel. J1
High (Default)
Standard effect.
Low
Sets when the high-frequency signals of the source are
emphasized excessively.
■ Parameters usable in surround decoder
q PLII Music only
Dimension
Adjusts the difference in level between the front sound field and
the surround sound field. You can adjust the difference in level
created by the software being played back to obtain the preferred
sound balance.
The surround sound gets stronger as you make the value more
negative, and the front sound gets stronger as you make the value
more positive.
Adjustable range
-3 to +3
Default setting
0
Panorama
Adjusts the soundscape of the front sound field. Sends front left/
right channels sounds to the surround speakers as well as the front
speakers for a wraparound effect.
Off (Default)
Disables the effect.
On
Enables the effect.
CT Width
Spreads the center channel sound to the front left and right
speakers to suit your needs or preferences. Set this parameter to 0
for outputting the center sound from the center speaker only, or to 7
for outputting it from the front left/right speaker only.
Adjustable range
0 to 100%
Adjustable range
0 to 7
Default setting
100%
Default setting
3
SR Level
Adjusts the volume of the surround R channel. J1
Adjustable range
0 to 100%
Default setting
100%
J 1 : Not displayed when speakers are set to be inactive.
En
43
SETUP
Extended functionality that can be configured as needed (Advanced Setup menu)
TRANSMIT
RECEIVER
SLEEP
HDMI
1
2
3
1
2
3
4
5
6
The Advanced Setup menu can be used for unit initialization and other useful extended functions. The Advanced Setup menu can be operated as follows.
Displaying/Setting the Advanced
Setup menu
AUDIO
3
In the Advanced Setup menu, you can set the following
settings.
TUNER
TUNER
MEMORY
PRESET
TUNING
INFO
ENHANCER
MOVIE
SOUND
MUSIC
STEREO
STRAIGHT SUR. DECODE
g
SCENE
BD
DVD
TV
SETUP
CD
RADIO
1
2
ENTER
VOLUME
Set this unit to the standby mode.
Press A while pressing and holding
STRAIGHT on the front panel.
Release the keys when “ADVANCED SETUP” is
displayed on the front panel display.
After approximately 2 seconds, the top menu items are
displayed.
OPTION
i
RETURN
MUTE
A
STRAIGHT
INFO
MEMORY
PRESET
TUNING
FM
SCENE
BD
DVD
PHONES
INPUT
TONE CONTROL
TV
CD
PROGRAM
RADIO
STRAIGHT
SILENT CINEMA
PROGRAM l / h
g SCENE
i Cursor D
REMOTEID-ID1
Use PROGRAM to select the item to be set
from the following items.
REMOTE ID
Changes the remote control ID of a
receiver.
TUNER (Asia and
General models
only)
Selects one of the following FM
frequency steps.
INIT
Initializes various settings for this unit.
4
5
Press STRAIGHT a few times to select the
value you wish to change.
Switch this unit to the standby mode, and
then switch it on again.
The settings become effective and the unit is powered
on. If initialization is selected, it will be performed
when the unit is powered on again.
Avoiding crossing remote control
signals when using multiple
Yamaha receivers
REMOTEID-ID1
The remote control of the unit can only receive signals
from a receiver which has an identical ID (remote
control ID). When using multiple Yamaha AV receivers,
you can set each remote control with a unique remote
control ID for its corresponding receiver.
On the contrary, if you are setting the same remote
control ID for all receivers, you can use one remote
control to operate 2 receivers.
ID1 (Default)
Receives the remote control signals set in
ID1.
ID2
Receives the remote control signals set in
ID2.
■ To change the remote control ID
To set the remote control ID to this unit ID, change ID
number as follows.
• To set to ID1
Press iCursor D and “BD/DVD” under gSCENE
for 3 seconds or longer.
• To set to ID2
Press iCursor D and “TV” under gSCENE for 3
seconds or longer.
En
44
SETUP
Extended functionality that can be configured as needed (Advanced Setup menu)
Changing FM frequency steps (Asia and
General models only)
TUNER -
FM50
You can select one of the following FM frequency steps: J1
FM100
You can adjust the FM frequency by steps of 100kHz.
FM50 (Default)
You can adjust the FM frequency by steps of 50kHz.
Initializing various settings for this unit
INIT-
CANCEL
Initializes various settings stored in this unit and sets it back to
default.
Select the items to be initialized from the following.
DSP PARAM
Initializes all parameters for the sound field programs.
ALL
Resets this unit to default factory settings.
CANCEL (Default)
Does not initialize.
J 1 : For details on setting FM frequency steps, refer to “FM tuning” (☞p. 26).
En
45
SETUP
Using the HDMI Control function
TRANSMIT
RECEIVER
SLEEP
HDMI
1
2
3
1
2
3
4
5
6
This unit supports the HDMI Control function, which
allows you to operate external components via HDMI. If
you connect devices that support HDMI Control (ex.
Panasonic VIERA Link-compatible TVs, DVD/Blu-ray
Disc recorders, etc.) J1, you can use the following
operations with the remote control of any of those
devices:
AUDIO
TUNER
TUNER
MEMORY
PRESET
TUNING
– Power synchronization (on/standby)
– Volume control, including Mute
– Changing the volume of the audio output signal device
(either the TV or this unit)
INFO
ENHANCER
MOVIE
SOUND
MUSIC
STEREO
STRAIGHT SUR. DECODE
SCENE
BD
DVD
TV
SETUP
CD
RADIO
h
TV
OPTION
ENTER
VOLUME
Control signal
(such as volume control)
i
1
Connect the TV, BD recorder supporting
HDMI Control to this unit’s HDMI output
jack.
2
Turn on the TV and this unit.
3
4
RETURN
MUTE
5
This unit
– Set the TV’s HDMI Control function to “On”
– Follow the AV amplifier connection instructions,
and connect this unit to the TV
L
SL
SW
C
R
SR
VOL.
L
SL
SW
C
R
SR
Press hSETUP when you have finished changing the
setting.
6
Turn the TV on.
9
Change the TV input setting to the input
jack that is connected to this unit (ex.
HDMI1).
Confirm that this unit has turned on in conjunction
with the TV. If it is still off, turn it on manually.
10
VOL.
Control;;;;;On
The following is an example of how to connect this
unit, a TV, and a BD recorder. Follow the instructions
in your TV and BD recorder manuals, as well as the
ones written below.
8
Other synchronized HDMI Control devices are turned
off with the TV. If they are not synchronized, turn them
off manually.
If BD recorder that supports the HDMI
Control function are connected to this
unit, turn them on.
Receiver unit
Confirm that the input source for the BD
recorder has been selected. If a different
input source has been selected, please
change it manually.
TV/BD recorder
Confirm that the video signal from the
recorder is being properly received by the
TV.
Make sure that “Control” is selected, and
then use iCursor D / E to select “On.”
HDMI
NOTE
h SETUP
i Cursor B / C / D / E
i ENTER
Use iCursor B / C to select “HDMI Setup”
and press iENTER.
Control;;;;Off
HDMI
Turn the TV off.
Press hSETUP. J2
HDMI
HDMI connection
Remote control of TV
Refer to the TV’s instruction manual on how to operate
external components.
7
Set HDMI control function of the TV and the
BD recorder to On.
Check the instruction manuals for those devices.
Operations 1-10 will not be required more than twice.
Continues to the
next page
J 1 : We recommend that you use TVs and BD/DVD recorders from
the same manufacturer whenever possible.
J 2 : Refer to the “Setting various functions (Setup menu)” (☞p. 33)
for details on the Setup menu.
En
46
SETUP
Using the HDMI Control function
TRANSMIT
RECEIVER
SLEEP
HDMI
1
2
3
1
2
3
4
5
6
11
AUDIO
Confirm that this unit is properly
synchronized with the TV through the
following operations by using the TV
remote control.
• Power On/Off
• Volume Control
• Switching between audio output devices
TUNER
TUNER
MEMORY
PRESET
TUNING
INFO
ENHANCER
MOVIE
SOUND
MUSIC
STEREO
STRAIGHT SUR. DECODE
SCENE
BD
DVD
TV
SETUP
CD
RADIO
h
If this unit is not synchronized to the TV’s power
operations, check that the HDMI Control function is
set to “On” for both devices. If they will not properly
synchronize, unplugging and re-plugging the devices
and turning them on and off may solve the problem.
To use other jacks to input audio signals from TV, carry
out the following procedure.
1
4
Connect this unit and the TV with an HDMI
cable.
HDMI
ENTER
VOLUME
i
■ Switching the input source on this
unit automatically when listening
to TV audio
2
Connect the TV audio output to this unit.
The input jacks listed below are available to input TV’s
audio signals. Use the same jack type as used for the
TV.
TV output jack
Input jack
Optical digital audio output
AUDIO 1 or AUDIO 4 (default)
Coaxial digital audio output
AUDIO 2 or AUDIO 3
Analog stereo output
AUDIO 5 or AUDIO 6
5
When the HDMI Control (☞p. 46) is operating properly,
the input source of this unit is automatically changed to
match operations carried out on the TV. The default
input jack is AUDIO 4. If the AUDIO 4 optical digital
jack is connected to the TV’s audio output jack, then you
can enjoy TV sound through this unit right away.
Available input jacks
OPTICAL
HDMI OUT
HDMI 2
TV
AUDIO 1
AUDIO 2
AUDIO 3
OPTICAL
COAXIAL
COAXIAL
OPTICAL
(CD)
( TV )
COAXIAL
HDMI 3
AUDIO 5
HDMI 2
HDMI 1
O
h SETUP
i Cursor B / C / D / E
i ENTER
L
SL
SW
C
R
SR
VOL.
L
SL
SW
C
R
SR
(BD/DVD)
(BD/DVD)
HDMI 1
HDMI
HDMI 3
7
Audio output
(Optical)
R
SR
Press iCursor C to select “TVAudio” and
select the input jack connected in step 2
using iCursor D / E.
TVAudio;AUDIO4
HDMI OUT
SW
C
VOL.
Control;;;;;On
6
L
SL
Make sure that “Control” is selected, and
then use iCursor D / E to select “On.”
HDMI
MUTE
OPTICAL
VOL.
Control;;;;Off
OPTION
RETURN
Use iCursor B / C to select “HDMI Setup”
and press iENTER.
COAXIAL
OPTICAL
(CD)
( TV )
Press hSETUP when you have finished
changing the settings.
If the TV hereafter transmits audio output signals, this
unit will automatically switch to the input source
chosen in step 6.
AUDIO 6
O
3
Press hSETUP. J1
J 1 : Refer to the “Setting various functions (Setup menu)” (☞p. 33)
for details on the Setup menu.
En
47
SETUP
Using the HDMI Control function
TRANSMIT
■ Single HDMI cable input to TV
RECEIVER
SLEEP
HDMI
1
2
3
1
2
3
4
5
6
audio with Audio Return Channel
function
When using a TV that supports HDMI functions and
Audio Return Channel function, audio/video output
from this unit to the TV or audio output from the TV to
this unit can be transmitted through a single HDMI cable
(Audio Return Channel function). Audio signals
transmitted from the TV to this unit can be assigned to
any input source.
AUDIO
TUNER
TUNER
MEMORY
PRESET
TUNING
INFO
ENHANCER
MOVIE
SOUND
MUSIC
STEREO
TV
SETUP
CD
RADIO
h
VOLUME
i
OPTION
ENTER
1
4
R
SR
VOL.
Control;;;;;On
L
SL
SW
C
R
SR
5
Press iCursor C to select “TVAudio” and
select the input source that you want to
assign to the HDMI audio signals from the
TV using iCursor D / E. J2
TV audio
output
6
Press iCursor C to select “ARC” and
press iCursor E to select “On.”
HDMI
The Audio Return Channel function will turn on.
HDMI
HDMI
(BD/DVD)
HDMI 1
HDMI 2
HDMI 3
VOL.
ARC;;;;;;;;;On
2
SW
C
Make sure that “Control” is selected, and
then use iCursor D / E to select “On.”
HDMI
MUTE
h SETUP
i Cursor B / C / D / E
i ENTER
L
SL
TV
HDMI
RETURN
HDMI OUT
VOL.
Control;;;;Off
Connect this unit and the TV with an HDMI
cable.
Video / Audio
output
Use iCursor B / C to select “HDMI Setup”
and press iENTER.
HDMI
STRAIGHT SUR. DECODE
SCENE
BD
DVD
3
Press hSETUP. J1
7
L
SL
SW
C
R
SR
Press hSETUP when you have finished
changing the settings.
If the TV hereafter transmits audio output signals, this
unit will automatically switch to the input source
chosen in step 6.
J 1 : Refer to the “Setting various functions (Setup menu)” (☞p. 33)
for details on the Setup menu.
J 2 : While the Audio Return Channel function is on, the jack selected
for the input source cannot be used.
En
48
APPENDIX
Troubleshooting
Refer to the table below when this unit does not function properly.
If the problem you are experiencing is not listed below, or if the instructions below do not help, turn off this unit, disconnect the power cable, and contact the nearest authorized Yamaha dealer or service
center.
General
Problem
Cause
Remedy
See
page
The power will not
turn on.
The internal circuits of the unit
have a problem.
The capability to turn on the power is
disabled as a safety precaution. Contact
your nearest Yamaha dealer or service
center to request repairs.
—
The unit enters
standby mode soon
after the power is
turned on.
The power cable is not completely
inserted.
Connect the power cable properly to an AC
wall outlet.
—
(When this unit is turned back on
and “Check SP Wires” is
displayed.) The protection
circuitry has been activated
because this unit was turned on
while a speaker cable was shorted.
Make sure that all speaker cables between
this unit and speakers are connected
properly.
11
This unit cannot be
turned off or does
not work properly.
The internal microcomputer is
hung-up due to an external electric
shock (such as lightning or
excessive static electricity) or by a
drop in power supply voltage.
Disconnect the power cable from the AC
wall outlet, wait about 30 seconds and then
plug it in again.
—
The batteries in the remote control
may have lost their charge.
Replace all batteries.
4
The unit enters
standby mode.
The protection circuitry has been
activated because of a short circuit,
etc.
Check that the speaker with an impedance
of at least 6Ω.
—
After display of a
countdown on the
front panel, the unit
goes into standby
mode.
If you do not use take any action,
the Auto Power Down function
operates.
Turn on the unit, and play the source again.
—
In the Setup menu “AutoPowerDown”
(“Func. Setup” → “AutoPowerDown”),
increase the time until switching to standby
mode, or turn off the Auto Power Down
function.
41
Problem
Cause
See
page
Remedy
“Internal Error” is
displayed on the
front panel display.
An internal error has occurred.
Please contact authorized Yamaha dealer or
service center to request repair.
—
Sound/images
suddenly go off.
The protection circuitry has been
activated because of a short circuit,
etc.
Check that the speaker wires are not
touching each other, then turn the unit back
on.
—
The sleep timer has turned off the
unit.
Turn on the unit, and play the source again.
—
En
49
APPENDIX
Troubleshooting
Problem
No sound.
Cause
See
page
Incorrect input or output cable
connections.
Connect the cables properly. If the problem
persists, the cables may be defective.
15
If a DVI-HDMI cable is used to
connect the unit with an external
component, then it is necessary to
use an audio input jack for a
different input to output audio.
Display the HDMI Input Option menu for
the connected cable, select “Audio In,” and
select the jack to use for audio input.
31
Speaker connections are not
secure.
Secure the connections.
11
The HDMI components connected
to the unit do not support the
HDCP copy protection standards.
Connect HDMI components that support the
HDCP copy protection standards.
31
The audio input into the device is
set to playback through the TV.
In the Setup menu, set the HDMI Audio Out
(“HDMI Setup” → “Audio”) to other than
“TV.”
39
Select an appropriate input source with
21
No appropriate input source has
been selected.
No picture.
Remedy
Problem
No sound is output
from a specific
speaker.
Cause
The speaker is malfunctioning.
Check the Speaker indicators on
the front panel display. If the
corresponding indicator lights up,
connect another speaker and check
if sound is output.
If sound is not output, the unit may be
malfunctioning.
The playback component or
speakers are not connected
properly.
Connect the cables properly. If the problem
persists, the cables may be defective.
11, 15
Output from that speaker is
disabled.
Check the Speaker indicators on the front
panel display. If the corresponding indicator
is turned off, try the following.
1) Change to a different input source.
2) With the selected sound field program,
sound is not output from that speaker. Select
another sound field program.
3) “None” may have been selected for that
speaker on this unit. Display “Speaker
Setup” in the Setup menu, and set respective
parameters to enable output from that
speaker (“Speaker Setup” → “Config”).
7, 34
The volume of that speaker is set
to the minimum in “Speaker
Setup” in the Setup menu.
Display “Speaker Setup” in the Setup menu
and adjust the volume (“Speaker Setup” →
“Level”).
35
(If hardly any sound comes from
one channel)
Speaker output balance is not set
correctly.
Balance the volume of each speaker from
“Level” in the Setup menu (“Speaker Setup”
→ “Level”).
35
Sound may not be output from
certain channels, depending on the
input source or sound field
program.
Try another sound field program.
22
When a monaural source sound
field program is applied, for some
surround decoders, sound from all
channels is output from the center
speaker.
Try another sound field program.
22
cInput selector (on the remote control).
The volume is turned down or
muted.
Turn up the volume.
—
Signals that this unit cannot
reproduce are being input from a
source component, such as a CDROM.
Use an input source that has signals that can
be reproduced on this unit.
—
An appropriate video input is not
selected on the TV.
Select an appropriate video input on the TV.
—
Only the center
speaker outputs
substantial sound.
See
page
Remedy
En
7
50
APPENDIX
Troubleshooting
Problem
No sound is heard
from the surround
speakers.
No sound is heard
from the subwoofer.
Cause
Remedy
See
page
This unit is in straight decoding
mode and a monaural source is
being played back.
Press fSTRAIGHT (on the remote
control) to exit straight decoding mode.
23
Sound may not be output from
certain channels depending on
input sources or sound field
programs.
Try another sound field program.
22
A subwoofer is not connected, or it
is disabled.
Check that a subwoofer is connected
correctly, and from the Setup menu
“Subwoofer” (“Speaker Setup” → “Config”
→ “Subwoofer”), set the subwoofer to
“On.”
34
(When using an active subwoofer)
The subwoofer is turned off.
Turn the subwoofer power on.
If the subwoofer includes an Auto Power
Off function, then lower the Auto Power Off
sensitivity settings.
—
The source does not contain LFE
(☞p. 54) or low frequency signals.
Problem
The volume cannot
be increased, or the
sound is distorted.
Cause
See
page
Remedy
The component connected to the
output jacks of this unit is not
turned on.
When the component connected to the
output jacks of this unit is not turned on, the
sound may be distorted, or the volume may
decreased due to the nature of AV receivers.
Turn on all components connected to this
unit.
—
“Max Volume” is set to a low
value.
Set it to a higher value with “Max Volume”
in “Sound Setup” in SETUP menu.
38
—
The audio input
sources cannot be
played in the desired
digital audio signal
format.
The connected component is not
set to output the desired digital
audio signals.
Set the playback component properly
referring to its instruction manual.
—
There is noise
interference from
digital or radio
frequency
equipment.
This unit is too close to other
digital or radio frequency
equipment.
Move this unit further away from such
equipment.
—
Noise/hum noise is
heard.
Incorrect cable connection.
Connect the audio cables properly.
If the problem persists, the cables may be
defective.
—
A DTS-CD is being played back.
If a DTS bitstream signal is not properly
input to this unit, only noise is output.
Connect the playback component to this
unit by digital connection and play back the
DTS-CD.
If the condition is not resolved, the problem
may result from the playback component.
Consult the manufacturer of the playback
component.
—
En
51
APPENDIX
Troubleshooting
HDMI™
Problem
Tuner (FM)
Cause
Remedy
See
page
FM
Problem
The front panel
display HDMI
indicator is flashing.
No picture or sound.
(When using HDMI
Control function)
TV sound is not
output from this unit
when operating the
remote control of the
TV.
An error with the HDMI
connection has occurred.
Try re-inserting the HDMI cable.
—
Confirm that HDMI video that is not
supported by the unit is not being input
(HDMI Input → Option menu → “Signal
Info”).
31
The number of components is over
the limit.
Disconnect some of the HDMI components.
—
The connected HDMI component
does not support high-bandwidth
digital copyright protection
(HDCP).
Connect an HDMI component that supports
HDCP.
—
The TV audio output is not
connected to this unit, or the
setting to match operations carried
out on TV is not set.
Connect the TV audio output to this unit,
and then select the connected input source
in “TVAudio” (Setup menu → HDMI Setup
→ TVAudio).
(When using Audio Return
Channel function)
The Audio Return Channel
function is not working.
Make sure that your TV supports Audio
Return Channel.
Set the Audio Return Channel function to
on (Setup menu → HDMI Setup → ARC).
FM stereo reception
is noisy.
Cause
You are too far from the station
transmitter, or the input from the
antenna is weak.
See
page
Remedy
Check the antenna connections.
17
Switch to monaural mode. Press FM MODE
on the front panel or switch to FM mode in
the Option menu.
27
Replace the outdoor antenna with a more
sensitive multi-element antenna.
—
There is multi-path interference.
Adjust the antenna height or orientation, or
place it in a different location.
—
39
There is distortion,
and clear reception
cannot be obtained
even with a good FM
antenna.
You are in an area far from a
station, or input from the antenna
is weak.
Replace the outdoor antenna with a more
sensitive multi element antenna.
—
Use dTUNING H / I (on the remote
control) to manually select the station.
26
39
The desired station
cannot be tuned into
with the automatic
tuning method.
“No Presets” is
displayed.
No preset stations are registered.
Register stations you wish to listen to as
preset stations before operation.
27
“Wrong Station!” is
displayed.
An invalid FM frequency has been
input.
Input a frequency that can be received.
—
En
52
APPENDIX
Troubleshooting
Remote control
Problem
The remote control
does not work or
function properly.
Cause
Remedy
See
page
Wrong distance or angle.
The remote control will function within a
maximum range of 6 m (20 feet), and no
more than 30 degrees off-axis from the front
panel.
—
Direct sunlight or lighting (from
an inverter type of fluorescent
lamp, strobe light, etc.) is striking
the remote control sensor of this
unit.
Adjust the lighting angle, or reposition this
unit.
—
The batteries are weak.
Replace all batteries.
4
The remote control ID of the
remote control and this unit do not
match.
Match the remote control ID of this unit and
the remote control.
44
En
53
APPENDIX
Glossary
Audio information
Audio and video synchronization (lip sync)
Lip sync, an abbreviation for lip synchronization, is a technical term that
involves both a problem, and the capability of maintaining audio and video
signals synchronized during post-production and transmission.
Whereas the audio and video latency requires complex end-user
adjustment, HDMI version 1.3 incorporates an automatic audio and video
syncing capability that allows devices to perform this synchronization
automatically and accurately without user interaction.
Dolby Digital
Dolby Digital is a digital surround sound system that gives you completely
independent multi-channel audio. With 3 front channels (front L/R and
center), and 2 surround stereo channels, Dolby Digital provides 5 full-range
audio channels. With an additional channel especially for bass effects,
referred to as LFE (Low-Frequency Effect), the system has a total of 5.1channels (LFE is counted as 0.1 channel). By using 2-channel stereo for the
surround speakers, more accurate moving sound effects and surround sound
environments are possible than with Dolby Surround. The wide dynamic
range from maximum to minimum volumes that are reproduced by the 5
full-range channels, and the precise sound orientation generated using
digital sound processing provides listeners with unprecedented excitement
and realism. With this unit, any sound environment from monaural up to a
5.1-channel configuration can be freely selected for your enjoyment.
Dolby Pro Logic II
Dolby Pro Logic II is an improved technique used to decode vast numbers
of existing Dolby Surround sources. This new technology enables a discrete
5-channel playback with 2 front left and right channels, 1 center channel,
and 2 surround left and right channels, instead of only 1 surround channel
for conventional Pro Logic technology. There are three modes available:
“Music mode” for music sources, “Movie mode” for movie sources, and
“Game mode” for game sources.
Dolby Surround
PCM (Linear PCM)
Dolby Surround uses a 4-channel analog recording system to reproduce
realistic and dynamic sound effects: 2 front left and right channels (stereo),
a center channel for dialog (monaural), and a surround channel for special
sound effects (monaural). The surround channel reproduces sound within a
narrow frequency range. Dolby Surround is widely used with nearly all
video tapes and laser discs, as well as in many TV and cable broadcasts.
The Dolby Pro Logic decoder built into this unit employs a digital signal
processing system that automatically stabilizes the volume on each channel
to enhance moving sound effects and directionality.
Linear PCM is a signal format under which an analog audio signal is
digitized, recorded and transmitted without using any compression. This is
used as a method of recording BD, DVD or CD audio. The PCM system
uses a technique for sampling the size of the analog signal per very small
unit of time. Standing for “Pulse Code Modulation,” the analog signal is
encoded as pulses and then modulated for recording.
DTS Digital Surround
DTS Digital Surround was developed to replace the analog soundtracks of
movies with a 5.1-channel digital sound track, and is now rapidly gaining
popularity in movie theaters around the world. DTS, Inc. has developed a
home theater system so that you can enjoy the depth of sound and natural
spatial representation of DTS Digital Surround in your home. This system
produces practically distortion-free 5.1-channel sound (technically, left,
right and center channels, 2 surround channels, plus an LFE 0.1 channel as
a subwoofer, for a total of 5.1-channels).
Sampling frequency and number of quantized bits
When digitizing an analog audio signal, the number of times the signal is
sampled per second is called the sampling frequency, while the degree of
accuracy when converting the sound level into a numeric value is called the
number of quantized bits. The range of rates that can be played back is
determined based on the sampling rate, whereas the dynamic range
representing the sound level difference is determined by the number of
quantized bits. In principle, the higher the sampling frequency, the wider
the range of frequencies that can be played back, and the higher the number
of quantized bits, the more accurately the sound level can be reproduced.
DSD
Direct Stream Digital (DSD) technology stores audio signals on digital
storage media, such as Super Audio CDs. Using DSD, signals are stored as
single bit values at a high-frequency sampling rate of 2.8224 MHz, while
noise shaping and oversampling are used to reduce distortion, a common
occurrence with very high quantization of audio signals. Due to the high
sampling rate, better audio quality can be achieved than that offered by the
PCM format used for normal audio CDs. The frequency is equal to or
higher than 100 kHz, with a dynamic range of 120 dB. This unit can
transmit or receive DSD signals via the HDMI jack.
LFE 0.1 channel
This channel reproduces low-frequency bass signals, and has a frequency
range from 20 Hz to 120 Hz. This channel is counted as 0.1, because it only
enforces a low-frequency range compared to the full-range reproduced by
the other 5 channels in Dolby Digital or DTS 5.1-channel systems.
En
54
APPENDIX
Glossary
Sound field program information
Video information
CINEMA DSP
Deep Color
Since the Dolby Surround and DTS systems were originally designed for
use in movie theaters, their effect is best felt in a theater having many
speakers designed for acoustic effects. Since home conditions, such as
room size, wall material, number of speakers, and so on, can differ so
widely, it is inevitable that there are differences in the sound that is heard.
Based on a wealth of actually measured data, Yamaha CINEMA DSP uses
Yamaha’s original DSP technology to combine Dolby Pro Logic, Dolby
Digital, and DTS systems to provide the audiovisual experience of a movie
theater in the listening room of your own home.
Deep Color refers to the use of various color depths in displays, up from the
24-bit depths in previous versions of the HDMI specification. This extra bit
depth allows HDTVs and other displays increase from millions of colors to
billions of colors and eliminate on-screen color banding for smooth tonal
transitions and subtle gradations between colors. The increased contrast
ratio can represent many times more shades of gray between black and
white. Additionally, Deep Color increases the number of available colors
within the boundaries defined by the RGB or YCbCr color space.
Compressed Music Enhancer
HDMI (High-Definition Multimedia Interface) is the first industry
supported, uncompressed, all-digital audio/video interface. Providing an
interface between any sources (such as set-top boxes or AV receivers) and
audio/video monitors (such as digital TV), HDMI supports standard,
enhanced or high-definition video as well as multichannel digital audio
using a single cable. HDMI transmits all ATSC HDTV standards and
supports 8-channel digital audio, with bandwidth to spare to accommodate
future enhancements and requirements.
When used in combination with HDCP (High-bandwidth Digital Content
Protection), HDMI provides a secure audio/video interface that meets the
security requirements of content providers and system operators. For
further information on HDMI, visit the HDMI website at
“http://www.hdmi.org/.”
The Compressed Music Enhancer feature of this unit enhances your
listening experience by regenerating the missing harmonics in compression
artifacts. As a result, it compensates for flattened complexity due to the loss
of high-frequency fidelity as well as lack of bass due to the loss of lowfrequency bass, providing improved performance for the overall sound
system.
SILENT CINEMA
Yamaha has developed a natural, realistic sound effect DSP algorithm for
headphones. Parameters for headphones have been set for each sound field
program, so that accurate representations of all the sound field programs
can be enjoyed on headphones.
Virtual CINEMA DSP
Yamaha has developed a Virtual CINEMA DSP algorithm that allows you
to enjoy DSP surround effects even without any surround speakers, by
using virtual surround speakers. It is even possible to enjoy Virtual
CINEMA DSP using a minimal two-speaker system that does not include a
center speaker.
HDMI
“x.v.Color”
A color space standard supported by HDMI version 1.3. It is a more
extensive color space than sRGB, and allows the expression of colors that
were not hitherto possible. While remaining compatible with the color
gamut of sRGB standards, “x.v.Color” expands the color space, and can
thus produce more vivid, natural images. It is particularly effective for still
pictures and computer graphics.
En
55
APPENDIX
Information on HDMI™
■ HDMI signal compatibility
NOTES
Audio signals
Audio signal types
Audio signal formats
Compatible media
2ch Linear PCM
2ch, 32-192 kHz, 16/20/24 bit
CD, DVD-Video, DVD-Audio, etc.
Multi-ch Linear PCM
8ch, 32-192 kHz, 16/20/24 bit
DVD-Audio, Blu-ray Disc, HD DVD,
etc.
DSD
2/5.1ch, 2.8224 MHz, 1 bit
SACD, etc.
Bitstream
Dolby Digital, DTS
DVD-Video, etc.
• If the input source component can decode the bitstream audio signals of audio commentaries, you can play back the audio
sources with the audio commentaries mixed down by using the digital audio input (optical or coaxial) connections.
• Refer to the supplied instruction manuals of the input source component, and set the component appropriately.
• When CPPM copy-protected DVD-Audio is played back, video and audio signals may not be output,
depending on the type of the DVD player.
• This unit is not compatible with HDCP-incompatible HDMI or DVI components.
• Refer to the supplied instruction manuals for details.
To decode audio bitstream signals on this unit, set the input source component appropriately so that the
component outputs the bitstream audio signals directly (does not decode the bitstream signals on the
component).
• This unit is not compatible with the audio commentary features (for example, the special audio contents
downloaded via Internet) of Blu-ray Disc or HD DVD. This unit does not play back the audio
commentaries of the Blu-ray Disc or HD DVD content.
Video signals
This unit is compatible with the video signals of the following resolutions:
–
–
–
–
480i/60 Hz
576i/50 Hz
480p/60 Hz
576p/50 Hz
– 720p/60 Hz, 50 Hz
– 1080i/60 Hz, 50 Hz
– 1080p/60 Hz, 50 Hz, 24 Hz
About trademarks
Manufactured under license from Dolby Laboratories.
“Dolby,” “Pro Logic,” and the double-D symbol are trademarks of Dolby Laboratories.
Manufactured under license under U.S. Patent Nos: 5,956,674; 5,974,380; 6,487,535 & other U.S. and
worldwide patents issued & pending. DTS, the Symbol, & DTS and the Symbol together are registered
trademarks & DTS Digital Surround and the DTS logos are trademarks of DTS, Inc. Product includes
software. © DTS, Inc. All Rights Reserved.
“HDMI,” the “HDMI” logo and “High-Definition Multimedia Interface” are trademarks, or registered
trademarks of HDMI Licensing LLC.
“SILENT CINEMA” is a trademark of Yamaha Corporation.
En
56
APPENDIX
Specifications
■ Input / Output
■ Compatible Decoding Formats
Input jacks
• Decoding Format
- Dolby Digital
• HDMI input x 3
• AUDIO input x 6
Digital input (optical) x 2, digital input (coaxial) x 2,
analog input x 2
Output jacks
- DTS
• Post Decoding Format
- Dolby Pro Logic
- Dolby Pro Logic II Music, Dolby Pro Logic II Movie,
Dolby Pro Logic II Game
• HDMI output x 1
• SUBWOOFER output x 1
■ HDMI
• HDMI Specification: Deep Color, “x.v.Color,” Lipsync,
ARC (Audio Return Channel), 3D
• Video Format (Repeater Mode)
- VGA
- 480i/60 Hz
- 576i/50 Hz
- 480p/60 Hz
- 576p/50 Hz
- 720p/60 Hz, 50 Hz
- 1080i/60 Hz, 50 Hz
- 1080p/60 Hz, 50 Hz, 24 Hz
• Audio Format
- Dolby Digital
- DTS
- DSD 6ch
- PCM 2ch-8ch (Max 192 kHz/24 bit)
• Content Protection: HDCP compatible
■ Audio Section
• Minimum RMS Output Power (1 channel driven)
(1 kHz, 0.9% THD, 6 Ω)
FRONT L/R........................................................................100 W/ch
CENTER .................................................................................100 W
SURROUND L/R...............................................................100 W/ch
(50 Hz, 0.9% THD, 6 Ω)
SUBWOOFER ........................................................................100 W
• Minimum RMS Output Power (2 channel driven)
[U.S.A. and Canada models]
(1 kHz, 0.9% THD, 6 Ω)
FRONT L/R..................................................................80 W + 80 W
CENTER ...................................................................................80 W
SURROUND L/R.........................................................80 W + 80 W
(50 Hz, 0.9% THD, 6 Ω)
SUBWOOFER ..........................................................................80 W
• Dynamic Power (IHF, 1 channel driven)
[U.S.A. and Canada models]
Front Speakers 6/4/2 Ω ............................................ 130/160/180 W
[Other models]
Front Speakers 6/4/2 Ω ............................................ 105/130/150 W
• Maximum Useful Output Power (JEITA, 1 channel driven)
[General and Asia models]
(1 kHz, 10% THD, 6 Ω)
FRONT L/R........................................................................135 W/ch
CENTER .................................................................................135 W
SURROUND L/R...............................................................135 W/ch
(50 Hz, 10% THD, 6 Ω)
SUBWOOFER ........................................................................135 W
• Dynamic Headroom [U.S.A. and Canada models]
6 Ω ........................................................................................ 0.23 dB
• Input Sensitivity/Input Impedance
AUDIO5, etc ..............................................................200 mV/47 kΩ
• Maximum Input Voltage
AUDIO5, etc. (1 kHz, 0.5% THD) ............................. 2.3 V or more
• Rated Output Voltage/Output Impedance
SUBWOOFER jack (2ch Stereo & Front: Small) ........1.0 V/1.2 kΩ
• Headphone Jack Rated Output/Impedance
AUDIO5, etc. (1 kHz, 50 mV)...................................100 mV/470 Ω
• Frequency Response
AUDIO5 to FRONT.............................. 10 Hz to 100 kHz, +0/-3 dB
• Total Harmonic Distortion
AUDIO5, etc. to FRONT (1 kHz, 50 W, 6 Ω) ............. 0.06% or less
• Signal to Noise Ratio (IHF-A Network)
AUDIO5, etc. Input Shorted (250 mV to Front Speakers)
................................................................................. 98 dB or more
• Residual Noise (IHF-A Network)
Front Speakers ........................................................... 150 µV or less
• Channel Separation (1 kHz/10 kHz)
AUDIO5, etc. (5.1 kΩ shortened)....................60 dB/45 dB or more
• Volume Control ...................................... MUTE / -80 dB to +16.5 dB
• Tone Control (Front Speakers)
BASS Boost/Cut .............................................. ±6 dB/2 dB at 50 Hz
BASS Turnover Frequency .................................................... 350 Hz
TREBLE Boost/Cut ....................................... ±6 dB/2 dB at 20 kHz
TREBLE Turnover Frequency.............................................. 3.5 kHz
• Filter Characteristics (fc=40/60/80/90/100/110/120/160/200 Hz)
H.P.F. (Front, Center, Surround) ....................................... 12 dB/oct.
L.P.F. (Subwoofer) ............................................................ 24 dB/oct.
En
57
APPENDIX
■ FM Section
• Antenna Input (unbalanced)......................................................... 75 Ω
• Tuning Range
[U.S.A. and Canada models] ...............................87.5 to 107.9 MHz
[Asia and General models] ........... 87.5/87.50 to 108.0/108.00 MHz
[Other models].................................................87.50 to 108.00 MHz
■ General
• 50 dB Quieting Sensitivity (IHF)
Mono..................................................................... 3.0 µV (20.8 dBf)
• Signal to Noise Ratio (IHF)
Mono/Stereo ................................................................. 72 dB/70 dB
• Harmonic Distortion (1 kHz)
Mono/Stereo ....................................................................... 0.3/0.3%
• Power Supply
[U.S.A. and Canada models]..................................AC 120 V, 60 Hz
[General models]......................... AC 110-120/220-240 V, 50/60 Hz
[Australia model] ...................................................AC 240 V, 50 Hz
[U.K. and Europe models] .....................................AC 230 V, 50 Hz
[Asia models] ............................................ AC 220-240 V, 50/60 Hz
• Standby Power Consumption
[General models] ..........................................................1.0 W or less
[Other models] ..............................................................0.5 W or less
• Dimensions (W x H x D)
435 x 151 x 315 mm (17-1/8 x 6 x 12-3/8 in)
• Weight
7.3 kg (16.1 lbs)
* Specifications are subject to change without notice.
• Power Consumption
[U.S.A. and Canada models]..................................... 250 W/320 VA
[Other models] ........................................................................250 W
Index
A
O
Advanced Setup menu ................................................................. 44
Antenna connection ..................................................................... 17
Audio Return Channel function ................................................... 48
Option menu................................................................................ 30
R
C
Rear panel...................................................................................... 6
Remote control, Part names and functions.................................... 8
Cable plug .................................................................................... 12
Connections.................................................................................... 9
S
E
External device connection .......................................................... 12
F
FM tuning..................................................................................... 26
Front panel ..................................................................................... 5
Front panel display......................................................................... 7
SCENE function.......................................................................... 22
Setup menu.................................................................................. 33
Sound field program.................................................................... 22
Sound field program parameter setting ....................................... 42
Speaker connection ....................................................................... 9
Speaker setting ............................................................................ 18
Supplied accessories...................................................................... 4
H
HDMI Control function ............................................................... 46
J
Jack .............................................................................................. 12
En
58
© 2011 Yamaha Corporation
YD769A0/OMEN
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising