RCA
EN
EN
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THE LIGHTNING
FLASH AND ARROWHEAD WITHIN THE
TRIANGLE IS A
WA R N I N G S I G N
ALERTING YOU OF
"DANGEROUS
VOLTAGE" INSIDE
THE PRODUCT.
CAUTION: TO REDUCE THE
RISK OF ELECTRIC SHOCK,
D O N OT R E M OV E C OV E R
( O R BAC K ) . N O U S E R S E RV I C E A B L E PA RT S I N S I D E . R E F E R S E RV I C I N G
T O Q UA L I F I E D S E RV I C E
PERSONNEL.
THE EXCLAMATION
POINT WITHIN THE
TRIANGLE IS A
WARNING
SIGN
ALERTING YOU OF
I M P O R TA N T
INSTRUCTIONS
A C C O M PA N Y I N G
T H E P R O D U C T.
SEE MARKING ON BOTTOM / BACK OF PRODUCT
WARNING: TO PREVENT FIRE OR ELECTRICAL
SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.
FCC Information
FCC Information
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two
conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
In accordance with FCC requirements, changes or
modifications not expressly approved by Thomson
Inc. could void the user’s authority to operate this
product.
This device generates and uses radio frequency
(RF) energy, and if not installed and used properly,
this equipment may cause interference to radio
and television reception.
If this equipment does cause interference to radio
or television reception (which you can determine
by unplugging the unit), try to correct the
interference by one or more of the following
measures:
• Re-orient the receiving antenna (that is, the
antenna for the radio or television that is
“receiving” the interference).
• Move the unit away from the equipment that is
receiving interference.
• Plug the unit into a different wall outlet so that
the unit and the equipment receiving interference
are on different branch circuits.
If these measures do not eliminate the
interference, please consult your dealer or an
experienced radio/television technician for
additional suggestions. Also, the Federal
Communications Commission has prepared a
helpful booklet, “How To Identify and Resolve
Radio TV Interference Problems.” This booklet is
available from the U.S. Government Printing
Office, Washington, DC 20402. Please specify stock
number 004-000-00345-4 when ordering copies.
CAUTION: FOR CONTINUED PROTECTION
AGAINST RISK OF FIRE, REPLACE ONLY WITH
SAME TYPE FUSE.
For Your Safety
The AC power plug is polarized
(one blade is wider than the
other) and only fits into AC
power outlets one way. If the
plug will not go into the outlet
completely, turn the plug over
and try to insert it the other
way. If it still does not fit, contact a qualified
electrician to change the outlet, or use a different
one. Do not attempt to bypass this safety feature.
CAUTION: TO PREVENT ELECTRIC
SHOCK, MATCH WIDE BLADE OF
PLUG TO WIDE SLOT, FULLY INSERT.
Technical Specification
Product: Clock Radio with CD player
Brand: RCA
Model: RP4801
Electrical Consumption
Power Supply: 120V~60Hz
Power Consumption: 11 Watts
IMPORTER
Comercializadora Thomson de México, S.A. de
C.V.
Álvaro Obregón No. 151. Piso 13.
Col. Roma. Delegación Cuauhtémoc
C.P. 06700. México, D.F.
Telefono: 52-55-11-020360
RFC: CTM-980723-KS5
For Your Records
In the event that service should be required, you
may need both the model number. In the space
below, record the date and place of purchase:
Date of Purchase:
Place of Purchase:
Service Information
This product should be serviced only by those
specially trained in appropriate servicing
techniques. For instructions on how to obtain
service, refer to the warranty included in this
Guide.
1
EN
Before you begin
EN
This clock radio is equipped with a memory
holding system that can be powered with
9V battery (not included). The power
failure protection circuit will not operate
unless battery is installed.
When normal household power is
interrupted, or AC cord is unplugged, the
battery will power the clock radio to keep
track of time and alarm settings
programmed into the memory. When the
battery backup functions, the digital
display will not light, however, the
function of alarm still occurs during the
power interruption if remaining battery
power is adequate. Normal operation will
resume after AC power is restored so you
will not have to reset the time or the
alarm.
Power Failure Indicator
When the AC power is interrupted
(disconnected) for a short period of time,
both time and alarm settings will change
(unless optional battery is installed). After
AC power is restored (reconnected), the
Digital Display will blink to indicate that
power was interrupted and you should
re-adjust the time and alarm settings.
Install battery as below:
1. Remove battery compartment door
(located at the bottom of the radio) by
applying thumb pressure to area
indicated on battery door and then lift
the door out and off the cabinet.
2. Connect a 9V battery to the connector
plug.
3. Insert battery in the compartment and
replace the compartment door.
The descriptions and characteristics in this owner’s manual are for the purpose of general
reference only and not as a guarantee. In order to provide you with the highest quality
product, we may make changes or modifications without prior notice. The English version serves
as the final reference on all product and operational details should any discrepancies arise in
other languages.
2
Operating the Clock
EN
SNOOZE
Setting time:
1. Press the SET button, the “ : “ will flash
on the display .
or FWD
to set the time.
2. Press REV
3. AM or PM icon will show beside the
time.
Tip:
No icon will be flashing if all
selectors are set, if you see
any icon flashing on display,
press the SET button repeatedly to
confirm everything is set correctly.
3
Operating the Radio
EN
FM
AM
TUNING
AM/FM
Tuning the Stations
Antennas
1. Press ON to turn on the radio.
2. Slide the FM/AM switch to the desired
broadcast band.
3. Turn the TUNING knob to select a
station.
4. Press OFF to turn off the radio.
AM Antenna - A built-in ferrite rod
antenna eliminates the need for an outside antenna for AM reception. Rotating
the unit slightly may improve the reception of distant AM stations.
Built-In AFC
The Built In Automatic Frequency Control
(AFC) works only on FM. It helps reducing
drift on FM reception and keeping the
radio locked in on the FM station to which
it is tuned.
When tuning in FM stations, you may
notice that the station you are tuning can
be well-tuned on two or three nearby
points on the dial. Always tune carefully
at the loudest and clearest point.
4
FM antenna - The power cord acts as your
FM antenna. It picks up moderate to
strong stations and eliminates the need for
an external antenna in most strong signal
areas. Be sure the power cord is stretched
to its full length. Do not coil or bunch the
cord together. Changing position of the
power cord may improve reception.
Tip:
You may try to move the
power cord in order to improve the reception.
Operating the CD player
EN
SNOOZE
Listening to compact disc
Selecting play mode
1. Lift to open the CD compartment door.
2. Insert a disc and close the door.
3. Press PLAY/PAUSE
.
4. Adjust volume to your desired level.
or FWD
to skip back5. Press REV
ward and forward.
6. Press STOP to stop CD playback.
1. Start CD playback.
2. During playback, press CD MODE to
toggle between different play mode.
Note:
REPEAT ONE - repeat the current track.
- repeat the whole disc.
REPEAT ALL
SHUFFLE
- play tracks randomly.
- play random
SHUFFLE REPEAT
track repeatedly.
When there is no disc in the
CD compartment, “nd” will
show on display.
5
Operating the Alarm
EN
Setting the WAKE Time
Waking by Selected Source
Your digital clock operates on a 12 hour
standard mechanism.
You may be woken up by WAKE
or CD .
1. Press the SET button until WAKE 1 /
WAKE 2 icon is blinking.
2. Press REV
or FWD
to set the wake
time. The time decrements or increments
will follow by a faster rate when you press
or FWD
.
and hold either REV
3. After the WAKE time is set, press SET
repeatedly until no icon is blinking.
1. Select an AM or FM station.
2. Set wake time (see above directions).
3. Press WAKE 2 or WAKE 1 to select waking up by WAKE , RADIO
or CD .
Corresponding indicator will be up next
to the selected setting.
4. Adjust the volume by turning VOLUME.
Tip:
The unit equips with GRADU-WAKE feature, the alarm
tone volume will increase
gradually to its maximum in
about 30 to 45 seconds.
, RADIO
You can select your CD wake track by the
following procedures.
1. Press WAKE UP CD TRACK.
or FWD
2. While pressing, press REV
to select your desired CD wake up track.
Note:
Tip:
If you set the SLEEP
function with low volume level
before going to bed, we
advise using WAKE mode to wake you
up since its volume will automatically
increase.
6
When you turn off the alarm
by pressing OFF
OFF, the alarm
will turn on at the same time
tomorrow.
Operating the Clock Radio
Sleep Mode
In sleep mode, the radio or CD will turn
off automatically. Simply:
1. Listen to CD or radio.
2. While holding SLEEP, press REV
or
FWD
to set the sleep time. The time
range is from 1 minute to 2 hours.
3. Release SLEEP and the current time will
be shown again. The radio or CD will turn
off when the preset time elapses. If you
decide to turn off the radio or CD sooner,
press SNOOZE or OFF.
4. When SLEEP is activated again, the sleep
time will be the same as the one you have
set before.
5. Press SLEEP to read the remaining sleep
time.
Stop the Nap alarm
Press NAP or follow “Turning off Alarm”.
1. Press and hold NAP to cancel the nap
setting.
2. Only alarm sound can be selected.
3. Nap alarm is equipped with GRAD-UWAKE feature.
Turning off Alarm
Silence the alarm momentarily
Press SNOOZE. The alarm will sound again
when the snooze period is over. (See
“Snooze Alarm Operation”).
Stop the alarm
Press OFF. The alarm will sound on the
following day at the same time.
Nap Mode
Disable the alarm permanently
This function wakes you up after a short
period of time. Simply:
1. Press CANCEL.
2. The WAKE indicator will be flashing.
3. Press WAKE 1 or WAKE 2 within 3
seconds to deactivate the corresponding
alarm function permanently.
1. Press NAP and release. The
indicator will flash. During this period, adjust
or FWD .
NAP time by pressing REV
The range is from 10 minutes to 2 hours.
2. The clock will be shown after 5 seconds
if no button is pressed. The
indicator
will lit up.
3. Press NAP once to show time left.
Tip:
You can activate the
previously set alarm time by
pressing WAKE 1 or WAKE
2.
7
EN
Operating the Clock Radio
EN
Snooze Alarm Operation
Seconds Time Display
This operation allows extra sleep time
after the alarm is on. The alarm will turn
off by pressing SNOOZE until the snooze
period is over. Snooze function can be
used repeatedly up to 2 hours. After this,
the alarm will turn off until the next alarm
conditions are met. Set the “quiet” period
as follow:
The unit may display in seconds.
1. Press and hold SNOOZE.
or FWD
to set the
2. Press REV
“quiet” period (the default time is 9 minutes) from 1 minute to 30 minutes. Release the button, then the “quiet” period
is set.
8
or FWD
to show sec1. Press REV
onds display.
2. Release REV
or FWD
to return
to the hour and minute display.
Brightness control
You can adjust the backlight by adjusting
the BRIGHTNESS switch at the back of
the unit, there are two modes you may
select from:
High — Stronger Backlight.
Low — Weaker Backlight.
U.S. Limited Warranty
What your warranty covers:
• Defects in materials or workmanship.
EN
For how long after your purchase:
• One year from date of purchase.
The warranty period for rental units begins with the first rental or 45 days from date of shipment to the
rental firm, whichever comes first.
What we will do:
• Provide you with a new, or at our option, a refurbished unit. The exchange unit is under warranty for
the remainder of the original product’s warranty period.
• Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that the product
is within the warranty period must be presented to obtain warranty service. For rental firms, proof of
first rental is also required.
How to make a warranty claim:
• Properly pack your unit. Include any cables, etc., which were originally provided with the product.
We recommend using the original carton and packing materials.
• Include evidence of purchase date such as the bill of sale. Also print your name and address and a
description of the defect. Send via standard UPS or its equivalent to:
Thomson Inc.
Product Exchange Center
11721 B Alameda Avenue
Socorro, Texas 79927
• Insure your shipment for of loss or damage. Thomson accepts no liability in case of damage or loss en
route to Thomson.
• Pay any charges billed to you by the Exchange Center for service not covered by the warranty.
• A new or refurbished unit will be shipped to you freight prepaid.
What your warranty does not cover:
• Customer instruction. (Your Owner’s Manual provides information regarding operating Instructions
and user controls. For additional information, ask your dealer.)
• Installation and setup service adjustments.
• Batteries.
• Damage from misuse or neglect.
• Products which have been modified or incorporated into other products.
• Products purchased or serviced outside the USA.
• Acts of nature, such as but not limited to lightning damage.
9
U.S. Limited Warranty
EN
Limitation of Warranty:
• THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PRODUCT. ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED (INCLUDING ALL IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) ARE HEREBY DISCLAIMED. NO
VERBAL OR WRITTEN INFORMATION GIVEN BY THOMSON INC., ITS AGENTS OR EMPLOYEES
SHALL CREATE A GUARANTY OR IN ANY WAY INCREASE THE SCOPE OF THIS WARRANTY.
• REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY
OF THE CONSUMER. THOMSON INC. SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF
ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. THIS DISCLAIMER OF WARRANTIES
AND LIMITED WARRANTY ARE GOVERNED BY THE LAWS OF THE STATE OF INDIANA. EXCEPT
TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED TO
THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE.
How state law relates to this warranty:
• Some states do not allow the exclusion nor limitation of incidental or consequential damages, or
limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply
to you.
• This warranty gives you specific legal rights, and you also may have other rights that vary from state
to state.
If you purchased your product outside the USA:
This warranty does not apply. Contact your dealer for warranty information.
10
Canadian Limited Warranty
Thomson Multimedia Ltd. warrants to the purchaser or gift recipient that if any manufacturing defect
becomes apparent in this product within 1 year from the original date of purchase, it will be replaced
free of charge, including return transportation.
This warranty does not include damage to the product resulting from accidents, misuse or leaking
batteries.
Should your product not perform properly during the warranty period, either:
1. Return it to the selling dealer with proof of purchase for replacement,
OR
2. Remove the batteries (where applicable), and pack product complete with accessories in the original
carton (or equivalent). Mail prepaid (with proof of purchase) and insured to:
Thomson Multimedia Ltd.
6200 Edwards Blvd.,
Mississauga, Ontario L5T 2V7
Canada
The provisions of this written warranty are in addition to and not a modification of or subtraction from
the statutory warranties and other rights and remedies contained in any applicable legislation, and to
the extent that any such provisions purport to disclaim, exclude or limit any such statutory warranties
and other rights and remedies, such provisions shall be deemed to be amended to the extent necessary
to comply therewith.
If you are unable to find a qualified servicer for out of warranty service, you may write to:
Thomson Inc.
P.O. Box 0944
Indianapolis, Indiana, U.S.A., 46206-0944
Attach your sales receipt to this booklet for future reference. This information is required if service is
needed during the warranty period.
PURCHASE DATE
NAME OF STORE
11
EN
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement