20V max* Lithium-ion CordLess driLL/driVer

20V max* Lithium-ion CordLess driLL/driVer
INSTRUCTION MANUAL
20V max* Lithium-Ion
Cordless DRILL/DRIVER
054-3118-6
Read and understand this instruction manual
thoroughly before using the product. It contains
important information for your safety as well as
operating and maintenance advice.
TECHNICAL SPECIFICATIONS 3
SAFETY GUIDELINES 4–8
DESCRIPTION9
OPERATING INSTRUCTIONS
10–16
MAINTENANCE 17–18
TROUBLESHOOTING 19
PARTS LIST 20
WARRANTY 21–22
Keep this instruction manual for future use. Should
this product be passed on to a third party, then this
instruction manual must be included.
20V max* Lithium-Ion Cordless DRILL/DRIVER - 054-3118-6
20V max* Lithium-Ion Cordless DRILL/DRIVER - 054-3118-6
TABLE OF CONTENTS
If any parts are
missing or damaged,
or if you have any
questions, please call
our toll-free helpline
at 1-800-689-9928.
2
MOTOR
20V DC
Chuck
1/2" Keyless chuck
No-Load Speed 0–420 RPM
0–1500 RPM
Max. Torque 330 in-lb
Clutch
23+1 Position
Cordless Drill/driver Weight (without battery)
2 lb 10 oz (1.2 kg)
4
WARNING!
Safety symbols in this Instruction Manual are used to flag possible dangers. The safety
symbols and their explanations require your full understanding. The safety warnings do not,
by themselves, eliminate any danger, nor are they substitutes for proper accident prevention
measures.
WARNING!
This Safety Alert Symbol indicates caution, warning, or danger. Failure to obey a safety
warning can result in serious injury to yourself or others. To reduce the risk of injury, fire, or
electric shock, always follow the safety precautions.
Know your tool
To operate this tool, carefully read this Instruction Manual and all labels affixed to the Cordless Drill/Driver
before using. Keep this instruction manual available for future reference.
Battery TypeLithium-Ion
Important
Battery Voltage
20V max* DC
This tool should only be serviced by a qualified service technician. For more information, call the toll-free
helpline at 1-800-689-9928.
Compatible Batteries
1.3 Ah Li-ion (054-3124-0)
2.6 Ah Li-ion (054-3125-8)
READ ALL INSTRUCTIONS THOROUGHLY.
Battery Charger
1-hour, diagnostic (054-3126-6)
*Maximum battery voltage without workload; with workload nominal voltage is 18V.
SAVE THESE INSTRUCTIONS.
Safety guidelines for cordless power tools
WARNING!
Read all safety warnings and instructions. Failure to follow the warnings and instructions may
result in electric shock, fire and/or serious injury. Save all warnings and instructions for future
reference. The term “power tool” in the warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power tool.
Work area safety
• Keep the work area clean and well lit. Cluttered or dark areas invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks, which may ignite the dust or fumes.
20V max* Lithium-Ion Cordless DRILL/DRIVER - 054-3118-6
20V max* Lithium-Ion Cordless DRILL/DRIVER - 054-3118-6
SAFETY GUIDELINES
TECHNICAL SPECIFICATIONS
3
SAFETY GUIDELINES
• Keep children and bystanders away while operating a power tool. Distractions can cause you to
lose control.
Electrical safety
• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of
electric shock.
• Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
Power tool use and care
• Do not force the power tool. Use the correct power tool for your application. The correct power tool will
do the job better and more safely at the rate for which it was designed.
• Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be repaired.
• Disconnect the plug from the power source and/or the battery pack from the power tool before
making any adjustments, changing accessories, or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool accidentally.
• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the
risk of electric shock.
• Store idle power tools out of the reach of children and do not allow persons unfamiliar with the
power tool or these instructions to operate the power tool. Power tools are dangerous in the hands
of untrained users.
• Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep the
cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of
electric shock.
• Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any
other condition that may affect the power tool’s operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly maintained power tools.
• When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric shock.
• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
• If operating a power tool in a damp location is unavoidable, use a ground-fault circuit interrupter
(GFCI) protected supply. Use of a GFCI reduces the risk of electric shock.
• Use the power tool, accessories, tool bits, etc., in accordance with these instructions, taking into
account the working conditions and the work to be performed. Use of the power tool for operations
different from those intended could result in a hazardous situation.
Personal safety
• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not
use tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while
operating power tools may result in serious personal injury.
• Use personal protective equipment. Always wear eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing protection, used for appropriate conditions, will reduce
personal injuries.
• Prevent unintentional starting. Ensure that the switch is in the off-position before connecting to a
power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger
on the switch or plugging in power tools that have the switch on invites accidents.
Battery tool use and care
• Recharge only with the charger specified by the manufacturer. A charger that is suitable for one
type of battery pack may create a risk of fire when used with another battery pack.
• Use power tools only with specifically designated battery packs. The use of any other battery pack
may create a risk of injury and fire.
• When the battery pack is not in use, keep it away from other metal objects, such as paper clips,
coins, keys, nails, screws, or other small metal objects that can make a connection from one
terminal to another. Shorting the battery terminals together may cause burns or a fire.
• Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result in personal injury.
• Under abusive conditions, liquid may be ejected from the battery. Avoid contact. If contact occurs,
flush with water. If liquid comes into contact with the eyes, seek medical help. Liquid ejected from the
battery may cause irritation or burns.
• Do not overreach. Keep proper footing and balance at all times. This enables better control of the power
tool in unexpected situations.
Service
• Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from
moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.
• Have your power tool serviced by a qualified repair person using only identical replacement
parts. This will ensure that the safety of the power tool is maintained.
• If devices are provided for the connection of dust extraction and collection facilities, ensure that
these are connected and properly used. Use of these devices can reduce dust-related hazards.
20V max* Lithium-Ion Cordless DRILL/DRIVER - 054-3118-6
20V max* Lithium-Ion Cordless DRILL/DRIVER - 054-3118-6
6
SAFETY GUIDELINES
5
8
Safety guidelines for cordless drill/driver
WARNING!
• Hold power tools by the insulated gripping surfaces when performing an operation where the tool
may contact hidden wiring or its own cord. Contact with a “live” wire may make exposed metal parts
of the power tool “live” and could give the operator an electric shock.
Remove the Cordless Drill/Driver from the package, and examine it carefully. Do not discard
the carton or any packaging material until all parts have been examined.
• When working with the power tool, always hold it firmly with both hands and provide for a secure
stance. The power tool is guided more securely with both hands.
WARNING!
• Keep the cord and charger from heat to prevent damage to the housing or internal parts.
If any part of the Cordless Drill/Driver is missing or damaged, do not attach the battery pack
to the tool or use the tool until the part has been repaired or replaced. Failure to heed this
warning could result in serious injury.
• Secure the workpiece. Clamping devices or a vise will hold the workpiece in place more effectively
than your hand can.
• Do not allow gasoline, oils, petroleum-based products, etc., to come in contact with plastic parts.
These materials contain chemicals that can damage, weaken, or destroy plastic.
• Always wait until the machine has come to a complete stop before placing it down. The tool insert
can jam and lead to loss of control over the power tool.
• Before performing any kind of work on the machine (e.g., maintenance, tool change, etc.) or
when transporting and storing the tool, always set the direction-of-rotation switch to the centre
(locked) position. Unintentional activation of the On/Off switch may result in personal injury.
• Do not open the battery. There is a risk of a short circuit.
• Protect the battery from heat and fire. There is a risk of explosion.
• Wear ear protectors when using the drill/driver. Exposure to noise can cause hearing loss.
• Use protective gloves when removing the bit from the tool, or first allow the bit to cool down. The
bit may be hot after prolonged use.
• Use protective gloves when operating the tool. Protective gloves can help to keep you from being
burnt or injured.
• Keep your hands away from the motor-housing vents. Hot gas comes from the vents during
operation.
• Release the trigger immediately when a screw is tightened to avoid breaking the screw.
• For best results, your battery tool should be charged in a location where the temperature is more
than 0°C (32°F) but less that 40°C (104°F). Do not store outside or in vehicles.
Contents
Cordless Drill/Driver, 2 double-ended bits, and Instruction Manual
20V max* Lithium-Ion Cordless DRILL/DRIVER - 054-3118-6
20V max* Lithium-Ion Cordless DRILL/DRIVER - 054-3118-6
SAFETY GUIDELINES
SAFETY GUIDELINES
7
2
1
10
WARNING!
Carefully read the Instruction Manuals for your Mastercraft 20V max* Lithium-Ion Battery
(054-3124-0/054-3125-8) and Mastercraft 20V max* Lithium-Ion Charger (054-3126-6,
5320.3) for safety and operation instructions.
To attach battery pack (fig 1)
7
8
3
6
CAUTION!
Avoid the possibility of accidental
starting. Always take care not to
activate the trigger switch when you
are attaching the battery pack or
performing other adjustments to the
tool.
fig 1
Battery-release button
NOTE: When placing a battery pack on the tool, be sure that the raised rib on the battery pack aligns with
the groove on the cordless drill/driver and the latches snap into place properly. Improper assembly of the
battery pack can cause damage to internal components.
1.Lock the trigger switch on the drill/driver by placing the direction-of-rotation (forward/centre-lock/
reverse) selector in the centre position.
2.Align the raised portion on the battery pack with the groove on the bottom of the drill/driver, and then
attach the battery pack to the drill/driver as shown.
5
4
No.Description
1
Two-speed gearbox switch
2
Forward/reverse LED indicator
3Direction-of-rotation selector
4
Bit clip
No.Description
5
LED Worklight
6
Trigger switch
7
Torque-adjustment ring
8
Keyless chuck
WARNING!
Do not allow familiarity with the Cordless Drill/Driver to cause a lack of alertness. A fraction of a second of carelessness is enough to cause severe injury.
3.Make sure that the latch on the battery pack snaps into place and that the battery pack is secured to the
drill/driver before beginning operation.
To detach battery pack (fig 1)
CAUTION!
Avoid the possibility of accidental starting. Always take care not to activate the trigger switch when you are detaching the battery pack or performing other adjustments to the tool.
1.Lock the trigger switch on the drill/driver by placing the direction-of-rotation selector (forward/
centre-lock/reverse) in the centre position.
2.Depress the battery-release button located on the front of the battery pack to release the battery pack.
3.Pull forward on the battery pack to remove it from the drill/driver.
20V max* Lithium-Ion Cordless DRILL/DRIVER - 054-3118-6
20V max* Lithium-Ion Cordless DRILL/DRIVER - 054-3118-6
OPERATING INSTRUCTIONS
Know your cordless drill/driver
DESCRIPTION
9
OPERATING INSTRUCTIONS
Trigger switch (fig 2)
To turn the drill/driver ON, depress the trigger
switch. To turn it OFF, release the trigger switch.
LED Worklight (fig 5)
fig 2
Variable speed
trigger switch
Variable speed (fig 2)
The variable-speed trigger switch delivers higher
speed with increased trigger pressure and lower
speed with decreased trigger pressure.
Direction-of-rotation selector
(forward/centre-lock/reverse)
(fig 3-4)
Direction-of-rotation
selector
fig 5
LED Worklight
Electric brake
To stop the tool, release the trigger switch and
allow the chuck to come to a complete stop. The
electric brake quickly stops rotation. This feature
engages automatically when you release the trigger
switch.
fig 3
The direction of rotation of the bit is reversible and
is controlled with a selector located above the
trigger switch. With the drill/driver held in normal
operating position:
Forward
Reverse
Keyless chuck (fig 6)
The arrows on the chuck indicate the direction of
rotation of the body of the chuck to: GRIP (tighten)
or OPEN (release) the jaws of the chuck on the drill
bit.
Position the direction-of-rotation selector to the left
of the tool for forward rotation. The forward/reverse
LED indicator the drill/driver will shine green (fig 4).
Position the direction-of-rotation selector to the right
of the tool for reverse rotation. The forward/reverse
LED indicator on the drill/driver will shine red (fig 4).
The LED worklight, located on the base of the
cordless drill/driver, will illuminate when the trigger
switch is depressed. This provides additional light
on the surface of the workpiece for operation in
lower light situations. The LED worklight will turn
off when the trigger switch is released.
12
fig 4
Position the direction-of-rotation selector in the
centre to lock the tool off.
NOTE: To prevent gear damage, always allow the
drill/driver to come to a complete stop before
changing the direction of rotation.
Bit storage (fig 7)
When not in use, the bits may be stored on either
side of the cordless drill/driver by snapping the bit
into place in one of the bit clips.
fig 6
RELEASE
Keyless chuck
GRIP
fig 7
Bit clip
NOTE: The drill/driver will not run unless the
direction-of-rotation selector is engaged fully to
the left or right.
20V max* Lithium-Ion Cordless DRILL/DRIVER - 054-3118-6
20V max* Lithium-Ion Cordless DRILL/DRIVER - 054-3118-6
OPERATING INSTRUCTIONS
11
OPERATING INSTRUCTIONS
Two-speed gear box (fig 8)
This drill/driver features a two-speed gearbox that
is designed for drilling or driving at LO speed or HI
speed. A slide switch is located on the top of the
cordless drill/driver to select either LO or HI speed.
fig 8
Slide switch
fig 10
RELEASE
Keyless chuck
3. Insert the drill bit.
GRIP
4. Rotate the chuck in the “GRIP” direction to tighten
the jaws of the chuck securely on the bit.
When using the cordless drill/driver in the HI speed
range, the speed will increase and the cordless
drill/driver will have less power and torque.
1. Lock the trigger switch by placing the
direction-of-rotation selector in the OFF (centre)
position.
2. Rotate the chuck in the “OPEN” direction to
release the jaws of the chuck on the bit.
When using the cordless drill/driver in the LO speed
range, the speed will decrease and the cordless drill/
driver will have more power and torque.
Use LO speed for high power and torque
applications, and use HI speed for fast drilling
applications.
Installing a bit (fig 10)
14
fig 9
Torque-adjustment ring
Do not hold the body of the chuck with
one hand while using the power of the
drill/driver to tighten the jaws of the
chuck on the drill bit. The body of the
chuck could slip in your hand, or your
hand could slip and come into contact
with the rotating bit. This could cause
an accident and result in serious
personal injury.
CAUTION!
Do not change between LO speed and
HI speed while the tool is running.
Failure to obey this caution could
result in serious damage to the
cordless drill/driver.
Arrow
Adjustable torque clutch (fig 9)
In general, use greater torque for larger screws, but if the torque is too high, the screws may be damaged
or broken. For delicate operations, such as removing a partially stripped screw, use a low torque setting. For
operations such as drilling into hardwood, use a higher torque setting.
NOTE: Do not change the torque setting when the tool is running.
NOTE: When adjusting the torque ring, make sure that the speed switch is either completely in the LO or the
HI position.
20V max* Lithium-Ion Cordless DRILL/DRIVER - 054-3118-6
WARNING!
Be sure to insert the drill bit straight into the jaws of the chuck. Do not tighten the jaws of the
chuck with the drill bit inserted at an angle, as shown in fig 11. Doing so could cause the drill
bit to be thrown from the drill/driver, which could result in possibly serious personal injury or
damage to the chuck.
The torque clutch can be adjusted to any of 24 different settings (23 driving and 1 drilling). The higher the
torque setting, the more force the cordless drill/driver produces to turn an object in either LO or HI rotation
speed.
When using the cordless drill/driver for driving applications, it is necessary to increase or decrease the
torque to help prevent damage to screw heads, threads, and the workpiece. Adjust the torque by rotating
the torque-adjustment ring. The proper setting depends on the job and the type of bit, fastener, and material
you will be using.
fig 11
WARNING!
Removing a bit (fig 10)
1. Lock the trigger switch by placing the direction-of rotation selector in the OFF (centre) position.
2. Open the jaws of the chuck (rotate in the “OPEN” direction.)
3. Remove the drill bit.
WARNING!
Use protective gloves when removing the bit from the tool, or first allow the bit to cool down.
The bit may be hot after prolonged use.
20V max* Lithium-Ion Cordless DRILL/DRIVER - 054-3118-6
OPERATING INSTRUCTIONS
13
General drilling (fig 12)
fig 12
WARNING!
Always wear safety goggles or safety
glasses with side shields during power
tool operation or when blowing dust.
If the operation is dusty, also wear a
dust mask.
Drilling mode operation
For drilling in wood, use twist bits, spade bits, power auger bits or hole saws.
1. When drilling “through” holes, place a block of wood behind the workpiece to prevent ragged or
splintered edges on the back side of the hole.
2. Select the desired speed to match the planned operation.
3. Begin drilling at a very low speed to prevent the bit from slipping off of the starting point, and then
increase the speed as the drill bit bites into the material.
1. Check the direction-of-rotation selector for the correct setting (forward or reverse).
4. If the drill/driver stalls, it is usually because it is being overloaded. Release the trigger switch
immediately, remove the drill bit from the work, and determine the cause of stalling.
2. Use a vise or clamps to secure the material to be drilled to keep it from turning as the drill bit rotates.
5. Keep the motor running when pulling the bit back out of the drilled hole. This will prevent jamming.
3. Hold the cordless drill/driver firmly, and place the bit at the point to be drilled.
4. Depress the trigger switch to start the cordless drill/driver.
For drilling in metal, use high speed steel twist drill bits.
5. Move the drill bit into the workpiece, applying only enough pressure to keep the bit cutting.
1. Use light oil on the drill bit to keep it from overheating; the oil will prolong the life of the bit and increase
the drilling action.
6. Do not force the cordless drill/driver or apply sideways pressure to elongate a hole. Allow the tool to do
the work.
2. When drilling a large hole, first use a smaller bit to drill a small pilot hole to prevent the larger bit from
slipping.
7. When drilling hard, smooth surfaces, use a centre punch to mark the desired location of the hole. This will
prevent the drill bit from slipping off-centre when the hole is started.
3. Select the desired speed to match the planned operation.
8. When drilling metal, use light oil on the drill bit to prevent it from overheating. The oil will prolong the life
of the bit and will increase the drilling efficiency.
9. If the bit jams in the workpiece or if the drill/driver stalls, stop the tool immediately. Reverse the direction
of rotation and gently squeeze the trigger to remove the bit from the workpiece. Investigate and correct
the cause of jamming before resuming work.
WARNING!
Be prepared for binding when the bit breaks through the workpiece, because the drill/driver
has a tendency to grab and kick opposite to the direction of rotation, which could cause a loss
of control. If the operator is not prepared, this loss of control could result in serious injury.
20V max* Lithium-Ion Cordless DRILL/DRIVER - 054-3118-6
4. Begin drilling at a very low speed to prevent the bit from slipping off the starting point. Maintain a speed
and pressure which allows cutting without overheating the bit.
5. If the drill stalls, it is usually because it is being overloaded. Release the trigger switch immediately,
remove the drill bit from the work, and determine the cause of stalling.
6. Keep the motor running when pulling the bit back out of the drilled hole. This will prevent jamming.
Screwdriver operation
1. Select the desired speed/torque range to match the planned operation.
2. Attach the desired fastener accessory into the chuck.
3. Make a few practice runs in a scrap piece before working.
20V max* Lithium-Ion Cordless DRILL/DRIVER - 054-3118-6
16
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
15
General maintenance
Chuck removal (fig 13)
The chuck can be removed and replaced with a new
one.
WARNING!
To avoid personal injury, always remove the battery pack from the tool when cleaning or
performing any maintenance.
1. Remove the battery.
WARNING!
3. Open the chuck jaws. Using a screwdriver,
remove the chuck screw by turning it clockwise.
Do not let brake fluids, gasoline, petroleum-based products, penetrating oil, etc. come into
contact with plastic parts. These substances contain chemicals that can damage, weaken, or
destroy plastic.
The tool may be cleaned most effectively with compressed dry air. Always wear safety
goggles when cleaning tools with compressed air.
Before each use:
2. Lock the trigger switch by placing the directionof-rotation selector in the centre position.
18
fig 13
Mallet
Chuck jaws
Hex wrench
4. Insert a 5/16-in. or larger hex key into the chuck
of the drill/driver and tighten the chuck jaws
securely.
5. Tap the hex key sharply with a mallet in a counter-clock wise direction. This will loosen the chuck for
easy removal.
6. Attach a new chuck to the spindle and tighten the chuck screw.
• Inspect the cordless drill/driver, the trigger switch, and the cord for damage.
• Check for damaged, missing, or worn parts.
• Check for loose screws, misalignment or binding of moving parts, or any other condition
that may affect the operation.
• If abnormal vibration or noise occurs, turn the cordless drill/driver off immediately, and
have the problem corrected before further use.
WARNING!
When servicing, use only identical replacement parts. The use of any other parts may create a
hazard or cause damage to the product.
WARNING!
Use only accessories that are recommended for this drill/driver by the manufacturer. Accessories that may be suitable for one tool may become hazardous when used with another tool.
WARNING!
To ensure safety and reliability, all repairs should be performed by a qualified service
technician.
20V max* Lithium-Ion Cordless DRILL/DRIVER - 054-3118-6
20V max* Lithium-Ion Cordless DRILL/DRIVER - 054-3118-6
MAINTENANCE
MAINTENANCE
17
PROBLEM
POSSIBLE CAUSES
SOLUTIONS
The drill/driver does
not work.
The battery is depleted.
Charge the battery.
1. The chuck is not opened.
1. Open the chuck.
The bit cannot be
installed.
The motor is overheating.
2. The bit does not fit the chuck.
2. Use a suitable bit.
Be sure the cooling vents are free from dust
and obstacles.
Clean and clear the vents. Do not cover with
your hand during operation.
20
Exploded view
PARTS LIST
TROUBLESHOOTING
19
If the problem remains unsolved after performing the checks described above, call the t­oll‑free helpline at
1-800-689-9928.
No. Part No.
01 2790306000
02 2790307000
03 3126500000
04 3126501000
05 3126502000
063126503000
07 3126506000
08 3321410000
09 3321411000
10 3402385000
113660466000
12 3700961000
133703673000
14 3810357000
15 3810405000
Description
Gear Case Assembly
Motor And Gear Assembly
LED Cover F/R Button
Speed Change Button
Lens
Clutch Cap
Left Housing Assembly
Right Housing Assembly
Contact Receptacle Assembly
Compression Spring
Stop Spring
Bits Holder
Screw Bit
Screw Bits
No. Part No.
17 4120311001
184360225000
19 4860003000
20 4860007000
21 4870452000
22 4890709000
23 4920154000
24 4920156000
25 4920158000
26 5610013000
275620422000
28 5620488000
295650007000
30 5660142000
31 5700178000
Description
Lead Resistor
LED
Inner Wire
Inner Wire
Trigger Switch
PCB Assembly
Shrinkable Tube
Shrinkable Tube
Shrinkable Tube
Tapping Screw
Screw
Screw (L.H.)
Spring Washer
Circlips For Shaft-Type B
Steel Ball
163860112000 Chuck
20V max* Lithium-Ion Cordless DRILL/DRIVER - 054-3118-6
20V max* Lithium-Ion Cordless DRILL/DRIVER - 054-3118-6
22
3
i) this warranty will not apply to component parts sold by and identified as the product of another company,
which shall be covered under the product manufacturer’s warranty, if any.
YEAR
LIMITED WARRANTY†
This Mastercraft product is guaranteed three (3) years from the
date of original retail purchase against defects in materials and
workmanship, except for the following components:
Additional Limitations
a) Component A: Batteries, chargers and carrying case, which are
guaranteed for a period of 2 years from the date of original retail
purchase against defects in workmanship and materials;
This warranty applies only to the original purchaser and may not be transferred. Neither the retailer
nor the manufacturer shall be liable for any other expense, loss or damage, including, without limitation,
any indirect, incidental, consequential or exemplary damages arising in connection with the sale,
use or inability to use this product.
b) Component B: Accessories, which are guaranteed for a period of
1-year from the date of original retail purchase against defects
in workmanship and materials.
Subject to the conditions and limitations described below, this product, if returned to us with proof
of purchase within the stated warranty period and if covered under this warranty, will be
repaired or replaced (with the same model, or one of equal value or specification), at our option. We will
bear the cost of any repair or replacement and any costs of labour relating there to.
Notice to Consumer
This warranty gives you specific legal rights, and you may have other rights, which may vary from province
to province. The provisions contained in this warranty are not intended to limit, modify, take away from,
disclaim or exclude any statutory warranties set forth in any applicable provincial or federal legislation.
IMPORTED BY MASTERCRAFT CANADA TORONTO, CANADA M4S 2B8
These warranties are subject to the following conditions and
limitations:
a)a bill of sale verifying the purchase and purchase date must be provided;
b)this warranty will not apply to any product or part thereof which is worn or broken or which has become
inoperative due to abuse, misuse, accidental damage, neglect or lack of proper installation, operation or
maintenance (as outlined in the applicable owner’s manual or operating instructions) or which is being
used for industrial, professional, commercial or rental purposes;
c) this warranty will not apply to normal wear and tear or to expendable parts or accessories that may be
supplied with the product which are expected to become inoperative or unusable after a reasonable
period of use;
d)this warranty will not apply to routine maintenance and consumable items such as, but not limited to,
fuel, lubricants, vacuum bags, blades, belts, sandpaper, bits, fluids, tune-ups or adjustments;
e)this warranty will not apply where damage is caused by repairs made or attempted by others (i.e.
persons not authorized by the manufacturer);
f) this warranty will not apply to any product that was sold to the original purchaser as a reconditioned or
refurbished product (unless otherwise specified in writing);
g) this warranty will not apply to any product or part thereof if any part from another manufacturer is
installed therein or any repairs or alterations have been made or attempted by unauthorized persons;
h) this warranty will not apply to normal deterioration of the exterior finish, such as, but not limited to,
scratches, dents, paint chips, or to any corrosion or discolouring by heat, abrasive and chemical cleaners;
and
20V max* Lithium-Ion Cordless DRILL/DRIVER - 054-3118-6
20V max* Lithium-Ion Cordless DRILL/DRIVER - 054-3118-6
WARRANTY
WARRANTY
21
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising