POWERGLIDE
®
LIFT-OFF
®
PET PLUS
Vacuum
USER GUIDE
2043 SERIES
More of a video person? Look for this icon and go online for an instructional how-to video at www.BISSELL.com
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING YOUR UPRIGHT VACUUM.
Always connect to a polarized outlet (one slot is wider than the other). Unplug from outlet when not in use and before conducting maintenance. When using an electrical appliance, basic precautions should be observed, including the following:
WARNING
TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK, OR INJURY:
» Do not leave vacuum cleaner when it is plugged in. Unplug from outlet when not in use and before servicing.
» Do not use outdoors or on wet surfaces.
» Do not allow to be used as a toy.
Close attention is necessary when used by or near children.
» Do not use for any purpose other than described in this User’s
Guide. Use only manufacturer’s recommended attachments.
» Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, have it repaired at an authorized service center.
» Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.
» Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
» Do not handle plug or vacuum cleaner with wet hands.
» Do not put any object into openings. Do not use with any opening blocked; keep openings free of dust, lint, hair, and anything that may reduce air flow.
» Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
» Turn off all controls before plugging or unplugging vacuum cleaner.
» Do not use to pick up flammable or combustible materials (lighter fluid, gasoline, kerosene, etc.) or use in areas where they may be present.
» Use extra care when cleaning on stairs.
» Do not use vacuum cleaner in an enclosed space filled with vapors given off by oil base paint, paint thinner, some moth proofing substances, flammable dust, or other explosive or toxic vapors.
» Do not use to pick up toxic material (chlorine bleach, ammonia, drain cleaner, etc.).
» Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
» Do not use without filters in place.
» Do not pick up hard or sharp objects such as glass, nails, screws, coins, etc.
» Use only on dry, indoor surfaces.
» Keep appliance on a level surface.
» Do not carry the vacuum cleaner while it is running.
» Unplug before connecting or disconnecting the Pet
TurboEraser® Tool.
NOTICE
With brushroll on, do not allow cleaner to sit in one location for an extended period of time, as damage to floor can result.
NOTICE
The brush roll continues to rotate while using your vacuum for above floor cleaning. To prevent carpet damage, turn the brush roll off and do not lean on vacuum or tilt forward.
To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a proper outlet. Do not change the plug in any way.
SAVE THESE INSTRUCTIONS
This model is for household use only.
2 www.BISSELL.com
Thanks for buying a BISSELL vacuum!
We love to clean and we’re excited to share one of our innovative products with you. We want to make sure your vacuum works as well as it does today for years to come, so this guide has tips on using (pages 6-7), maintaining
(pages 7-9), and if there is a problem, troubleshooting (page 10).
In just a few simple assembly steps, you’ll be ready to vacuum. Flip to page 5 and let’s get started!
What’s In The Box?
Screw
(taped to handle)
Hose
Pet TurboEraser®
Tool
Pet Hair Eraser®
Tool
PetTurboEraser®
Tool Holder
Upper
Handle
Base Unit
Crevice Tool/
Extension Wand
Holder
Extension
Wand
Combination
Dusting/Crevice
Tool
NOTE: Standard accessories may vary by model. To identify what should be included with your purchase, please refer to the “Carton Contents” list located on the carton top flap.
Safety Instructions. . . . . . . . . . . 2
Product View. . . . . . . . . . . . . . . .4
Assembly . . . . . . . . . . . . . . . . . . . 5
Operations . . . . . . . . . . . . . . . . 6-7
Maintenance & Care . . . . . . . 7-9
Troubleshooting . . . . . . . . . . . . 10
Warranty . . . . . . . . . . . . . . . . . . . .11
Service . . . . . . . . . . . . . . . . . . . . . .11
Product Registration. . . . . . . . 12
Parts & Supplies . . . . . . . . . . . . 12 www.BISSELL.com
3
Getting to Know Your Vacuum
1
11
16
4
3
2
5
6
8
7
9
12
13
14
15
10
1. Handle
2. Lift-Off Canister Release Button
3. Dirt Tank Release Button
4. Carry Handle
5. Brush Roll Power Switch
6. Power Switch
7. Quick Release® Cord Wrap
8. Power Cord
9. Filter Cover (Pre-Motor and Post-Motor
Filters are located under Filter Cover)
10. Brush Roll
11. Cord Clip
12. Pet TurboEraser® Tool Holder with Tool
13. Stretch Hose
14. Crevice Tool & Extension Wand Holder with Tools
15. Hose Wand Base
16. Pet Hair Eraser® Tool (does not store on unit; only available select models)
Cord Release and Storage
Twist Cord Release down to quickly remove cord
4 www.BISSELL.com
Assembly
WARNING
Do not plug in your vacuum until you are familiar with all instructions and operating procedures.
1 2
Slide handle into vacuum base. Attach with the screw that is taped to the handle.
Attach hose by lining the tabs on the cuff with the notches on the back of vacuum. Twist clockwise to lock hose into place.
3 4 5
6
Push handle end into base of vacuum on opposite side.
Slide the Crevice Tool/
Extension Wand Holder down onto the middle of the back of base.
7
To use your optional
Febreze® filter (included), press the tank release button and pull dirt tank away from vacuum.
Slide the Pet TurboEraser® tool holder down on the top back of the base.
Remove the black/ yellow foam filter and replace with the black
Febreze® filter. Be sure to place the Febreze® filter last, covering the the mesh filter. Place dirt container back on vacuum.
www.BISSELL.com
5
PowerBrush Switch
WARNING
Before using your vacuum, make sure that the dirt container is in locked position and that all filters, both pre and post-filters are in place. DO NOT operate your vacuum without these filters.
1 2
Power
On/Off
Switch
Brush Roll
On/Off Switch
Turn vacuum on by pressing Power
Switch on (I - ON and O - OFF).
Press the Brush Roll switch to run the
PowerBrush for carpet cleaning (brush roll is on when light on switch is illuminated).
NOTE: The brush roll will automatically shut off when vacuum is locked in upright position, recline to reactivate.
NOTE: Turn the Brush Roll OFF when vacuuming hard or delicate surfaces that may be caught by the rotating brush. This could include hard wood, tiled floors, small area rugs or frieze carpets that have long delicate fibers or threads.
1
Adjusting the Variable Suction
2
FULL
Locate the Variable suction control
Valve on the Hose
Wand Base.
moves to indicate suction level
REDUCED
Full
Reduced
Suction
suction control
To decrease the amount of suction suction level
REDUCED for cleaning delicate carpets, curtains, or rugs; twist the variable suction valve counterclockwise.
NOTE: The vacuum will come with the Variable Suction Valve closed for full suction power.
Full
Suction
Reduced
Suction
6 www.BISSELL.com
3
1
Above Floor Cleaning
2
Clean stairs or furniture easily with the removable canister. Push the green button to remove and attach desired tool.
4
Use the Pet
TurboEraser® tool for best results on your stairs.
To get the most reach, attach both the extension wand and Combination
Dusting/Crevice Tool.
Replace the canister back on vacuum by aligning the front with the base of vacuum, then lean canister back and lock into place.
Emptying the Dirt Tank
WARNING
To reduce the risk of electrical shock, turn power switch off and disconnect polarized plug from electrical outlet before performing maintenance or troubleshooting checks.
1 2
Press tank release button, grab the handle to pull dirt container away from vacuum.
3
Vacuum tank is full, time to empty!
Holding dirt container over a trash bin, press tank empty button.
4
Close bottom of container and place back on the vacuum.
Be sure you place the front of the tank first and push back to
“click” into place.
www.BISSELL.com
7
Cleaning Inner Cyclone
1
2
3
With dirt container off vacuum base, push the empty tank button and twist counter-clockwise to remove the separator and pull down.
Tap separator against inside of trash bin and rinse with warm water if necessary. Be sure to let it completely dry before placing back in the dirt container.
Place separator back in, being sure to align each tab on either side of the top of separator with the notches inside the top of the dirt container.
Cleaning Filters
WARNING
Do not operate vacuum with damp or wet filters, as well as without filters or the Dirt
Container in place. Allow components to dry before reassembling the Dirt Container.
1 2
With vacuum unplugged, remove the tank and lift up on the tab attached to the filter cover.
There are 2 filters here; one foam filter on top and a thinner fiber filter; both are washable.
3 Remove post-motor filter located on the front of the vacuum underneath the filter cover. If it appears dirty, remove the filter and gently tap the filter on the edge of a waste basket.
4
Replace the postmotor filter by pushing it straight back, clicking each side.
NOTE: The post-motor filter is a pleated filter. This filter is not washable and must be replaced when it becomes dirty.
Parts & Supplies
For Parts and Supplies, go to www.BISSELL.com and enter your model number in the search field.
8 www.BISSELL.com
1
Replace Belt & Brush
Unplug vacuum, turn over and unscrew 8 Silver Phillips head screws to remove bottom cover.
2
Pull roller straight out and slide belt off brush roll and motor gear.
3
5
Inspect brush roll by placing it on its end and spin. The brush roll should spin freely, multiple times by one flick. If it doesn’t, replace brush roll.
Inspect belt, replace if it appears damaged.
6
4
Place belt back on brush roll.
7
Re-attach bottom cover with 8 screws.
Pinch belt around brush roll & hook back around the silver motor gear.
Rotate brush roll into place and line up end caps.
1
Maintain the Pet TurboEraser® Tool
2 Paddle Wheel
Twist gray collar counter-clockwise, until slot appears, and then separate faceplate.
Belt
Roller
Remove brush roll, belt, and paddle wheel. Inspect for damages and replace if necessary.
3 4
To reassemble, align two clips on each end of paddle wheel with belt on and pop back into place.
Replace brush roll with belt, making sure all parts are aligned correctly.
To put faceplate back on, align the tabs in the top of the cover and place it down to
“click” into place.
www.BISSELL.com
9
Troubleshooting
WARNING
To reduce the risk of electric shock, turn power switch off and disconnect plug from electrical outlet before performing maintenance or troubleshooting checks.
Problem
Vacuum cleaner won’t turn on
Possible causes
Power cord not plugged in
Blown fuse/tripped breaker
Pod is not securely seated
No power at rotating floor brush
Visible dirt escaping from cleaner
Brush switch turned to "OFF"
Vacuum is in upright position
Remedies
Check electrical plug
Check/replace fuse or reset breaker
Remove pod and replace, making sure that it "clicks" into place
Make sure brush switch is in "ON" position
Recline vacuum to operate brush
Vacuum cleaner won’t pick up dirt
Hose not attached to suction opening
Crack or hole in hose
Broken or worn drive belt
Grasp quick reach handle and firmly push hose wand onto the suction opening
Check hose and replace if needed
Replace drive belt, see page 9
Rotating floor brush bristles worn Replace brush
Rotating floor brush jammed Remove brush and clean debris from brush ends
Clog in vacuum Check for debris build-up or clogs in the inner tank, hose and foot/lower hose
Empty dirt container Dirt container full
Dirt container or secondary cyclone not installed properly
Filters are dirty
Position correctly and lock in place
Check and clean pre-motor and post-motor filters, see page 8
Dirt container full
Filters or secondary cyclone missing or installed incorrectly
Empty dirt container
Check secondary cyclone, pre-motor and post-motor filters for correct installation
Dirt container installed incorrectly Pull out and re-insert dirt container correctly
10 www.BISSELL.com
Warranty
This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state. If you need additional instruction regarding this warranty or have questions regarding what it may cover, please contact BISSELL Consumer
Care by E-mail, telephone, or regular mail as described below.
Limited Five-Year Warranty
Subject to the *EXCEPTIONS AND
EXCLUSIONS identified below, upon receipt of the product BISSELL will repair or replace
(with new or remanufactured components or products), at BISSELL’s option, free of charge from the date of purchase by the original purchaser, for five years any defective or malfunctioning part.
See information below on "If your BISSELL product should require service".
This warranty applies to product used for personal, and not commercial or rental service. This warranty does not apply to fans or routine maintenance components such as filters, belts, or brushes. Damage or malfunction caused by negligence, abuse, neglect, unauthorized repair, or any other use not in accordance with the User's Guide is not covered.
BISSELL IS NOT LIABLE FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGES OF ANY
NATURE ASSOCIATED WITH THE USE OF
THIS PRODUCT. BISSELL’S LIABILITY WILL
NOT EXCEED THE PURCHASE PRICE OF
THE PRODUCT.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
*EXCEPTIONS AND EXCLUSIONS FROM
THE TERMS OF THE LIMITED WARRANTY
THIS WARRANTY IS EXCLUSIVE AND
IN LIEU OF ANY OTHER WARRANTIES
EITHER ORAL OR WRITTEN. ANY IMPLIED
WARRANTIES WHICH MAY ARISE
BY OPERATION OF LAW, INCLUDING
THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE, ARE LIMITED
TO THE FIVE YEAR DURATION FROM
THE DATE OF PURCHASE AS DESCRIBED
ABOVE.
Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you.
NOTE: Please keep your original sales receipt. It provides proof of date of purchase in the event of a warranty claim.
Service
If your BISSELL product should require service:
Contact BISSELL Consumer Care to locate a BISSELL Authorized Service Center in your area.
If you need information about repairs or replacement parts, or if you have questions about your warranty, contact BISSELL Consumer Care.
Website: www.BISSELL.com
E-mail: www.BISSELL.com/email-us
Call:
BISSELL Consumer Care
1-800-237-7691
Monday – Friday 8am - 10pm ET
Saturday 9am - 8pm ET
Sunday 10am - 7pm ET
Please do not return this product to the store.
Other maintenance or service not included in the manual should be performed by an authorized service representative.
For any questions or concerns, BISSELL is happy to be of service.
Contact us directly at 1-800-237-7691.
www.BISSELL.com
11
12
Register your product today!
Registering is quick, easy and offers you benefits over the lifetime of your product.
You’ll receive:
BISSELL Rewards Points
Automatically earn points for discounts and free shipping on future purchases.
Faster Service
Supplying your information now saves you time should you need to contact us with questions regarding your product.
Product Support Reminders and Alerts
We’ll contact you with any important product maintenance reminders and alerts.
Special Promotions
Optional: Register your email to receive notice of offers, contests, cleaning tips and more!
Visit www.BISSELL.com/registration!
Visit the BISSELL website: www.BISSELL.com
When contacting BISSELL, have model number of cleaner available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
NOTE: Please keep your original sales receipt. It provides proof of purchase date in the event of a warranty claim. See Warranty on page 11 for details.
Parts & Supplies
For Parts and Supplies, go to www.BISSELL.com and enter your model number in the search field.
We can’t wait to hear from you!
Rate this product and let us (and millions of your closest friends) know what you think!
www.BISSELL.com
©2016 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in China
Part Number 161-1025 11/16 RevA
Visit our website at: www.BISSELL.com
