Yamaha MCRN670D Mini System CD player

Yamaha MCRN670D Mini System CD player
AVEEA71102A
English
Important Notice: Guarantee Information for customers in EEA* and Switzerland
For detailed guarantee information about this Yamaha product, and Pan-EEA* and
Switzerland warranty service, please either visit the website address below (Printable file is available at our website) or contact the Yamaha representative office for your country.
* EEA: European Economic Area
N et wor k C D Pl ayer
http://europe.yamaha.com/warranty/
O WNER ’S MANUAL
© 2015 Yamaha Corporation
Printed in China ZS21820
AB
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
i
To assure the finest performTo assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
Install this sound system in a well ventilated, cool, dry, clean place - away from direct sunlight,
heat sources, vibration, dust, moisture, and/or cold. For proper ventilation, allow the following
minimum clearances.
Top: 10 cm (4 in), Rear: 6 cm (2.5 in), Sides: 6 cm (2.5 in)
Locate this unit away from other electrical appliances, motors, or transformers to avoid humming
sounds.
Do not expose this unit to sudden temperature changes from cold to hot, and do not locate this unit
in an environment with high humidity (i.e. a room with a humidifier) to prevent condensation
inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal
injury.
Avoid installing this unit where foreign object may fall onto this unit and/or this unit may be
exposed to liquid dripping or splashing. On the top of this unit, do not place:
– Other components, as they may cause damage and/or discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause fire, damage to this unit, and/or personal
injury.
– Containers with liquid in them, as they may fall and liquid may cause electrical shock to the
user and/or damage to this unit.
Do not cover this unit with a newspaper, tablecloth, curtain, etc. in order not to obstruct heat
radiation. If the temperature inside this unit rises, it may cause fire, damage to this unit, and/or
personal injury.
Do not plug in this unit to a wall outlet until all connections are complete.
Do not operate this unit upside-down. It may overheat, possibly causing damage.
Do not use force on switches, knobs and/or cords.
When disconnecting the power cable from the wall outlet, grasp the plug; do not pull the cable.
Do not clean this unit with chemical solvents; this might damage the finish. Use a clean, dry cloth.
Only voltage specified on this unit must be used. Using this unit with a higher voltage than
specified is dangerous and may cause fire, damage to this unit, and/or personal injury. Yamaha
will not be held responsible for any damage resulting from use of this unit with a voltage other
than specified.
To prevent damage by lightning, keep the power cable and outdoor antennas disconnected from a
wall outlet or this unit during a lightning storm.
Do not attempt to modify or fix this unit. Contact qualified Yamaha service personnel when any
service is needed. The cabinet should never be opened for any reasons.
When not planning to use this unit for long periods of time (i.e. vacation), disconnect the AC
power plug from the wall outlet.
Be sure to refer to the “Troubleshooting” section for common operating errors before concluding
that this unit is faulty.
Before moving this unit, press A to set it to standby mode and disconnect the AC power plug from
the wall outlet.
En
18 Condensation will form when the surrounding temperature changes suddenly. Disconnect the
power cable from the outlet, then leave this unit alone.
19 When using this unit for a long time, this unit may become warm. Turn the power off, then leave
this unit alone for cooling.
20 Install this unit near the AC outlet and where the AC power plug can be reached easily.
21 The batteries shall not be exposed to excessive heat such as sunshine, fire or the like. When you
dispose of batteries, follow your regional regulations.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
UNIT TO RAIN OR MOISTURE.
This unit is not disconnected from the AC power source as long as it is connected to the wall
outlet, even if this unit itself is turned off by A. This state is called the standby mode. In this
state, this unit is designed to consume a very small quantity of power.
Radio waves may affect electro-medical devices. Do not use this unit near medical devices or
inside medical facilities.
Do not use this unit within 22 cm (9 inches) of persons with a heart pacemaker implant or
defibrillator implant.
■ Notes on remote controls and batteries
• Do not spill water or other liquids on the remote control.
• Do not drop the remote control.
• Do not leave or store the remote control in the following conditions:
– places of high humidity, such as near a bath
– places of high temperatures, such as near a heater or stove
– places of extremely low temperatures
– dusty places
• Insert the battery according to the polarity markings (+ and -).
• Change all batteries if you notice the following conditions:
– the operation range of the remote control narrows
– the transmit indicator does not flash or is dim
• If the batteries run out, immediately remove them from the remote control to prevent an explosion or
acid leak.
• If you find leaking batteries, discard the batteries immediately, taking care not to touch the leaked
material. If the leaked material comes into contact with your skin or gets into your eyes or mouth,
rinse it away immediately and consult a doctor. Clean the battery compartment thoroughly before
installing new batteries.
• Do not use old batteries together with new ones. This may shorten the life of the new batteries or
cause old batteries to leak.
• Do not use different types of batteries (such as alkaline and manganese batteries) together.
Specification of batteries may be different even though they look the same. Danger of explosion
may happen if batteries are incorrectly replaced.
• Before inserting new batteries, wipe the compartment clean.
• Dispose of batteries according to your regional regulations.
• Keep batteries away from children. If a battery is accidentally swallowed, contact your doctor
immediately.
• When not planning to use the remote control for long periods of time, remove the batteries from the
remote control.
• Do not charge or disassemble the supplied batteries.
The user shall not reverse engineer, decompile, alter, translate or disassemble the software
used in this unit, whether in part or in whole. For corporate users, employees of the corporation
itself as well as its business partners shall observe the contractual bans stipulated within this
clause. If the stipulations of this clause and this contract cannot be observed, the user shall
immediately discontinue using the software.
LASER SAFETY
This unit employs a laser. Due to possible eye injury, only a qualified service person should
remove the cover or attempt to service this device.
DANGER
This unit emits visible laser radiation when open. Avoid direct eye exposure to beam. When
this unit is plugged into the wall outlet, do not place your eyes close to the opening of the disc
tray and other openings to look into inside.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herein
may result in hazardous radiation exposure.
■ For U.K. customers
If the socket outlets in the home are not suitable for the plug supplied with this appliance, it
should be cut off and an appropriate 3 pin plug fitted. For details, refer to the instructions
described below.
Note
The plug severed from the mains lead must be destroyed, as a plug with bared flexible cord is
hazardous if engaged in a live socket outlet.
■ Special Instructions for U.K. Model
IMPORTANT
THE WIRES IN MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE
FOLLOWING CODE:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this apparatus may not correspond with the
coloured markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the terminal which is marked with
the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to
the terminal which is marked with the letter L or coloured RED.
Making sure that neither core is connected to the earth terminal of the three pin plug.
The laser component in this product is capable of emitting radiation exceeding the limit for
Class 1.
En
ii
Information for Users on Collection and Disposal of Old
Equipment and Used Batteries
These symbols on the products, packaging, and/or accompanying documents
mean that used electrical and electronic products and batteries should not be
mixed with general household waste.
For proper treatment, recovery and recycling of old products and used batteries,
please take them to applicable collection points, in accordance with your
national legislation and the Directives 2002/96/EC and 2006/66/EC.
By disposing of these products and batteries correctly, you will help to save
valuable resources and prevent any potential negative effects on human health
and the environment which could otherwise arise from inappropriate waste
handling.
For more information about collection and recycling of old products and
batteries, please contact your local municipality, your waste disposal service or
the point of sale where you purchased the items.
[Information on Disposal in other Countries outside the European
Union]
These symbols are only valid in the European Union. If you wish to discard
these items, please contact your local authorities or dealer and ask for the
correct method of disposal.
Note for the battery symbol (bottom two symbol examples):
This symbol might be used in combination with a chemical symbol. In this case
it complies with the requirement set by the Directive for the chemical involved.
We, Yamaha Music Europe GmbH hereby declare that this unit is in compliance with the
essential requirements and other relevant provisions of Directive 1999/5/EC.
Yamaha Music Europe GmbH
Siemensstr. 22-34 25462 Rellingen, Germany
Tel: +49-4101-303-0
iii
En
Bluetooth
• Bluetooth is a technology for wireless communication between devices within an area of about 10
meters (33 ft) employing the 2.4 GHz frequency band, a band which can be used without a license.
Handling Bluetooth communications
• The 2.4 GHz band used by Bluetooth compatible devices is a radio band shared by many types of
equipment. While Bluetooth compatible devices use a technology minimizing the influence of other
components using the same radio band, such influence may reduce the speed or distance of
communications and in some cases interrupt communications.
• The speed of signal transfer and the distance at which communication is possible differs according
to the distance between the communicating devices, the presence of obstacles, radio wave
conditions and the type of equipment.
• Yamaha does not guarantee all wireless connections between this unit and devices compatible with
Bluetooth function.
Table of Contents
What you can do with this unit······2
Introduction······3
Performing pairing and playing back music······26
Connecting a paired Bluetooth device
and playing back music······27
Supplied accessories······3
About this manual······3
Playing back music from external
devices······28
Listening to DAB stations (CDNT670D only)······29
Part name······4
Front panel······4
Rear panel······5
Front panel display······6
Remote control······7
Preparations······8
Connecting amplifier······8
Connecting antenna······9
Turning on the power······10
Configuring network connection······11
Selecting connection method······11
Preparing for network connection······12
Connecting to the wired network······14
Connecting to the wireless network······16
Establishing wireless direct connection with mobile
device······19
Playing back music on your CD······21
Playing back music on USB
devices······22
Playing back songs in the
computer······23
Initial scan······29
Tuning in DAB stations······29
Presetting DAB stations······30
Selecting preset DAB stations······30
Confirming the reception······31
Listening to the FM radio
stations······32
Tuning in FM stations······32
Presetting FM stations······32
Selecting preset FM stations······33
Radio Data System (U.K. model only)······34
Option menu list······44
Updating the firmware······45
Troubleshooting······46
General······46
Network······47
Bluetooth······48
Disc······49
USB devices······50
DAB reception (CD-NT670D only)······50
FM reception······51
Messages on the front panel display······52
Supported devices/media and file
formats······53
Specifications······55
Trademarks······56
Listening to the Internet radio······35
Playing back music with AirPlay······36
Playing back songs with iPod······36
Playing back songs with iTunes······36
More on playback······37
Playing back music via Bluetooth
connection······25
Shuffle playback······37
Repeat playback······37
Playback information······38
Presetting network contents······39
Selecting preset network content······39
Presetting music contents to FAVORITES······40
Selecting network content registered to FAVORITES······40
FAVORITES registration list······41
Pairing a Bluetooth device with the unit······25
Using the sleep timer······42
Setting the media sharing of music files······23
Playing back songs in the PC······24
Option settings······43
En
1
What you can do with this unit
• This unit is a network CD player, on which you can enjoy playing back music files stored on your media server (PC or NAS) and USB devices, audio content on the
Internet radio, FM radio, CD, AirPlay devices (iPod/iTunes), and external devices including DVD disc players, by connecting the unit to your home network and
audio system on the same network.
• This unit supports various streaming services (supported streaming services depend on your region).
• You can select songs and operate the unit easily by using the free dedicated "MusicCast CONTROLLER" app supporting iOS/Android. See "MusicCast Setup
Guide" for details.
1 Play back the Internet radio (& P.35)
Amplifier
Internet
Bluetooth device
2 Play back music files stored on your PC (& P.23)
CD
3 Play back music files stored on your NAS (& P.23)
FM radio
DAB
Modem
4 Play back music in a Bluetooth device (& P.25)
5 Play back your iPod with AirPlay (& P.36)
Use of MusicCast CONTROLLER (& P.11)
6 Play back a CD (& P.21)
7 Play back music in an USB device (& P.22)
Router*
This unit
PC
Listening to DAB stations (CD-NT670D only)
(& P.29)
9 Play back music in an external device (& P.28)
USB
DVD disc player, etc.
(External devices)
NAS
Mobile device (AirPlay (iPod),
MusicCast CONTROLLER)
* You need a commercially available wireless router (access point) when you use a mobile device.
2
En
8 Listening to the FM radio stations (& P.32)
Introduction
Confirm the package contents and useful points of this manual.
Supplied accessories
About this manual
• Instructions and illustrations used in this manual refer to the CD-NT670, unless otherwise
specified.
• How to operate this unit is described mainly using the remote control.
• iOS and Android mobile devices are collectively referred to as “mobile devices.” The
specific type of mobile device is noted in explanations as needed.
• “iPod” described in this manual may also refer to “iPhone” or “iPad.”
Remote control
FM antenna
(for CD-NT670)
RCA stereo cable
• Illustrations may differ from actual item depicted.
• Symbols:
Indicates precautions for use of the unit and its feature limitations.
Indicates supplementary explanations for better use.
&
Batteries (× 2)
(AA, R6, UM-3)
DAB/FM antenna
(for CD-NT670D)
Indicates the corresponding reference page(s).
MusicCast Setup Guide
En
3
Part name
Familiarize yourself with all parts and these functions.
Front panel
1 A (Power) (& P.10)
2 USB jack (& P.22)
3 Disc tray (& P.21)
4 Bluetooth indicator (& P.26)
5 Wi-Fi indicator (& P.16)
6 Front panel display (& P.6)
7
(Open/close the disc tray) (& P.21)
8 Remote control sensor
9
(& P.21, 22, 24)
PRESET </> (& P.33)
0
(Play/pause)
(& P.21, 22, 24)
A
(Stop) (& P.21, 22, 24, 35)
CONNECT
Use to control the unit using the dedicated "MusicCast
CONTROLLER" app for mobile device. See "MusicCast
Setup Guide" for details.
B INPUT (& P.21, 22)
Turn left or right to change the audio source. (The source
is shown on the front panel display.)
4
En
Part name
Rear panel
1 ANTENNA jack (& P.9)
2 AUX IN jacks (RCA input) (& P.28)
3 ANALOG OUT jacks (& P.28)
4 SYSTEM jack (mini jack input)
Connect to the pre-main amplifier (A-670/A-U670). For
details, see the owner's manual that comes with your
pre-main amplifier.
5 Wireless antenna (& P.16)
6 NETWORK jack (& P.12)
Connects to a network using a commercially available
network cable.
7 DIGITAL IN jack (optical input) (& P.28)
8 Power cable (& P.10)
En
5
Part name
Front panel display
1 Multi information display
Shows various information, such as the music
information and radio frequency.
Characters shown on the front panel display are
alphanumerics only.
2 STEREO indicator
Lights up when the unit is receiving a strong signal from
an FM stereo broadcast.
3 TUNED indicator
Lights up when the unit is tuned into FM station.
4 MUTE indicator
Lights up when the sound is muted (& P.7).
5 SLEEP indicator
Lights up when the sleep timer is set
(& P.42).
6
En
6 Shuffle/repeat indicator
Lights up when you shuffle or repeat music of your CD,
USB device or computer (& P.37).
• MUTE indicator can function only when the premain amplifier (A-670/A-U670) is connected with
the system.
Adjusting display brightness
You can adjust the brightness of the front panel
display by pressing the DIMMER button on the
remote control (& P.7).
• Each press of the button changes the brightness:
bright (default), mid dim, or dim.
Part name
Remote control
1 Infrared signal transmitter
E DISPLAY (& P.38)
2
F HOME (& P.24, 35)
(Open/close the disc tray) (& P.21)
3 Source buttons
G SLEEP (& P.42)
Switch the audio source to be played.
4 Numeric buttons (& P.21, 39)
Installing batteries
5 MEMORY (& P.32, 39)
6 Audio control, cursor control buttons (& P.21, 22,
24, 35)
7 REPEAT (& P.37)
8 SHUFFLE (& P.37)
9 DIMMER (& P.6)
0 FAVORITES (& P.40)
Check the “+” and “-” of the batteries and inset them the
correct way around.
A A (Power) (& P.10)
B OPTION (& P.43)
C VOLUME +/Controls the volume.
D MUTE
Turns mute on or off.
• Change both batteries when the operation range
of the remote control decreases.
• VOLUME and MUTE can be used only when the
pre-main amplifier (A-670/A-U670) is connected
with the system. For details, see the owner's
manual that comes with your pre-main amplifier.
En
7
Preparations
Connect an amplifier or antenna and turn the unit on.
Do not connect the power cable of the unit until you have finished connecting all cables.
Connecting amplifier
Connect the amplifier to the unit, as the
illustration shows.
• Use the supplied stereo pin cable to connect the unit to
the audio input jacks of the amplifier.
• To play content with the unit, make sure to connect the unit to an amplifier and speaker.
• Depending on the device to be connected or connection environment, you may not be able to correctly play content.
Check also the specifications and settings of the source device.
• You can also connect powered speakers to the unit.
8
En
Preparations
Connecting antenna
1
2
Supplied antenna
2
Connect the supplied antenna to the
unit.
Install it with pins where the unit can
obtain good reception.
1
• Be sure to stretch out the antenna as the illustration shows.
• If radio reception with the supplied antenna is not satisfactory, a commercially available outdoor antenna may improve
reception.
En
9
Preparations
Status in standby/eco standby
Turning on the power
Plug the power cable into the wall outlet
and press
.
• The unit turns on.
• Press
again to turn off (standby mode).
• You can set the mode to “eco standby”, which
consumes less power. If set to “eco standby”, some
operations are restricted (See the table on the right).
Setting to the eco standby
A
Within 6 m
(20 ft)
A
Standby
Eco
standby
Charging of USB devices
3
—
Operation of the source
buttons*
3
3
CD load/eject
3
3
AirPlay
3
—
Control from the app
3
—
Bluetooth
3
—
* Operation with the remote control only
Option menu regarding power (System Config)
You can set the mode to the eco standby by turning off
the network standby.
1
AutoPowerStdby
Press
.
• The option menu is shown on the front panel
display.
2
• Select [Off] with S/T and press ENTER to set.
10
1,3
OPTION
Setting to the eco standby.
• Set the item in the order of [System Config] - [Net
Standby].
3
(Bold: default)
Press
En
to finish the option setting.
2
S/T,
ENTER
Configure the setting so that the unit automatically enters
the standby status.
(On, Off)
When set to On, the unit automatically enters the standby
status under the following conditions according to the
music source.
• Network/Bluetooth/CD/USB: When no operation or
playback is performed for 20 minutes
• Other sources: When no operation is performed for 8 hours
• If the network connection is not set, turn the power
on to display “Share WiFi Set” on the front panel
display and trigger an automatic iOS device search.
See “Sharing the setting of iOS device” (& P.18) for
details on the iOS device and network connection.
Configuring network connection
Select a method of connecting to the network. You can play back music files stored on your PC, mobile devices, DLNA*-compatible NAS, or audio contents on the
Internet, by connecting this unit to the network. You can also operate the unit with your mobile device.
* Digital Living Network Alliance
Selecting connection
method
Using “MusicCast CONTROLLER” to
make connection
You can set the network connection by using the free
dedicated "MusicCast CONTROLLER" app installed to your
mobile device.
See “MusicCast Setup Guide” for details.
With MusicCast CONTROLLER, you can use the following
functions in addition to the network setting.
Establishing connection by the unit
operation
You can also connect to the network by using the
following methods beside using “MusicCast
CONTROLLER”.
Connecting to wired network
Setting wired network connection
(& P.14).
Connecting to wireless network
Setting wireless network connection
(& P.16).
• Play songs stored on computers (servers)
Connecting by Wireless Direct
• Select an Internet radio station
Setting the wireless direct connection with
mobile device (& P.19).
• Distribute and receive audio between the unit and
other Yamaha MusicCast devices
• It is recommended to use wired connection to
keep a stable connection.
• For details on Internet connection, refer to the
owner’s manuals of your network devices.
• If you are using a router that supports DHCP, you
do not need to configure any network settings for
the unit. If you are using a router that does not
support DHCP, configure the network setting from
[Network Config] in the option setting (& P.43).
• Some security software installed on your PC or the
firewall settings of network devices (such as a
router) may block the access of the unit to the
network devices or the Internet. In this case,
change the setting of the security software or
network devices.
• When setting the subnet manually, each server
must be connected to the same subnet as the unit
(& P.44).
En
11
Configuring network connection
Preparing for network
connection
This unit
Preparing for wired connection
Connect the unit to the router as shown on
the right.
• Connect with a commercially available STP (shielded
twisted pair) network cable (CAT-5 or higher, straightthrough cable).
Network cable
LAN
Router
12
En
Configuring network connection
Preparing for wireless connection
Put up the wireless antenna.
• Put up the wireless antenna on the rear panel of the
unit.
• Do not apply excessive force to the antenna. Doing so may damage the antenna.
• Check the orientation of the movable part and bend it in the correct direction.
• Do not remove the antenna.
En
13
Configuring network connection
Connecting to the
wired network
This unit
Mobile device
Connect the unit to the network using a cable.
You need to connect in advance the NETWORK jack of the
unit to the router using a network cable (& P.12).
PC
LAN
Router
Network cable
Internet
Modem
WAN
Network attached storage
(NAS)
14
En
Configuring network connection
1
Press
.
• The option menu is shown on the front panel
display.
2
3
4
Select [Network Config] with S/T,
and press
.
Select [Select Network] with S/T,
and press
.
Select [Wired] with S/T, and press
.
• By default, [Wired] is set for the unit.
1
OPTION
2, 3, 4
S/T
ENTER
En
15
Configuring network connection
Connecting to the
wireless network
Connect the unit to network wirelessly.
Put up the wireless antenna of the unit in advance
(& P.13).
Mobile device
Internet
Modem
PC
Wireless router
(access point)
This unit
• You cannot simultaneously use this setting with the wired network connection or the Wireless Direct.
• If the unit is placed away from the wireless router (access point), connection may not be able to be established. In that
case, place them closer together.
• If the unit cannot be connected to the wireless router (access point),, you can use the Wireless Direct to play back music
files in mobile devices (& P.19).
• Once the connection is complete, the Wi-Fi indicator lights up.
16
En
Configuring network connection
• Once the connection is complete, the Wi-Fi
indicator lights up.
Setting with WPS button
You can easily establish a connection only by pressing the
WPS button on the wireless router (access point).
• A wireless router (access point) with the WPS button is
required.
1
Press
.
• The option menu is shown on the front panel display.
2
3
4
5
6
Select [Network Config] with S/T,
and press
.
1
Select [Select Network] with S/T,
and press
.
OPTION
Select [Wireless] with S/T, and press
.
Select [WPS] with S/T, and press
.
2, 3, 4, 5
S/T
ENTER
Press the WPS button on the wireless
router (access point).
About WPS
WPS (Wi-Fi Protected Setup) is a standard established by
the Wi-Fi Alliance, which allows easy establishment of a
wireless home network.
En
17
Configuring network connection
• You need iOS device with iOS7.1 or later.
Sharing the setting of iOS device
• If the network setting of the iOS device is set to be
shared, all the network and the Bluetooth
connection settings will be initialized. Also the
account information of streaming services will be
initialized.
You can apply the network setting of your iOS device
(iPhone or other iOS devices) to the unit to connect the
device to the unit easily.
Before starting setting, check that your iOS device is
connected to the wireless router (access point).
1
2
3
4
5
6
Press
.
• The option menu is shown on the front panel
display.
Select [Network Config] with S/T,
and press
.
1
Select [Select Network] with S/T,
and press
.
OPTION
Select [Wireless] with S/T, and press
.
2, 3, 4, 5
Select [Share WiFi Set] with S/T, and
press
.
• A message for the initialization of the network will
be shown on the front panel display. Press
ENTER.
Display the Wi-Fi setup screen on the
iOS device and select the unit from
“SETUP A NEW AIRPLAY SPEAKER...”.
• Follow the on-screen instructions displayed on
the iOS device.
18
• Once the connection is complete, the Wi-Fi
indicator lights up.
En
S/T
ENTER
Configuring network connection
Establishing wireless
direct connection with
mobile device
Connect the unit directly with the mobile device
wirelessly.
Put up the wireless antenna of the unit in advance
(& P.13).
Mobile device
This unit
• You cannot simultaneously use this setting with the wired network connection or the wireless network connection.
• When using the Wireless Direct, you cannot connect the unit to the Internet. Therefore, the Internet services, such as the
Internet radio, are unavailable.
• For details about how to set Wi-Fi connection of the mobile device, see the user's guide of your mobile device.
En
19
Configuring network connection
1
2
3
4
5
6
7
Press
.
Select [Network Config] with S/T,
and press
.
Select [Select Network] with S/T,
and press
.
Select [WiFi Direct] with S/T, and
press
.
Select desired security method with
S/T, and press
.
1
OPTION
• Available choices are: [OPEN], [WPA2-PKS(AES)]
Check the SSID and the security key.
• These values are required for Wi-Fi setting of the
mobile device.
• You can check the value from the option menu [Network Info] - [WiFi Direct Info].
Configure the Wi-Fi setting of the
mobile device.
• Enable the Wi-Fi function of the mobile device.
• When the access points are listed, select the SSID
you have checked in step 6.
• When the terminal prompts you to enter a
password, enter the security key you have
checked in step 6.
20
• If you select [OPEN] in step 5, the connection may
be insecure since the communication is not
encrypted.
• The option menu is shown on the front panel
display.
En
2, 3, 4, 5
S/T
ENTER
Playing back music on your CD
This unit allows playback of audio CDs and data CDs in which the MP3/WMA files are recorded.
For details on playable CDs, see “Supported devices/medias” (P.53).
1
2
Turn INPUT to select [CD] or press
on the remote control.
Set a CD in a disc tray.
• Press
3
to open/close the disc tray.
2
• When CD playback is stopped, playback will
resume from the beginning of the song last
played. Pressing
while playback is stopped will
clear resume playback.
1
INPUT
• You can cancel the song number selected with
the numeric buttons by pressingW.
• If you turn off the unit with CD selected as music
source and a CD set in it, the unit automatically
plays back the set CD next time you turn on the
unit.
Playback starts.
The remote control functions are shown below.
Play/pause
1
Stop
CD
Skip to the beginning of the song being
played back or the previous song/press
and hold to fast rewind.
Skip to the next song/press and hold to
fast forward.
SHUFFLE
Starts shuffle playback (& P.37).
REPEAT
Starts repeat playback (& P.37).
1 - 9, 0
Specify the song number.
ENTER
Confirmation of the song number
selected with the numeric buttons.
3
En
21
Playing back music on USB devices
This unit allows playback USB devices which music files are recorded.
For details on playable USB devices, see “Supported devices/medias” (P.53).
1
2
3
Turn INPUT to select [USB] or press
on the remote control.
Connect a USB device to the USB port.
Browse and select a song.
1
S
T
Shows other item.
ENTER/X
Confirms the selected item and proceeds
to the next level or start playback.
HOME
Shows the top-level item.
W
Returns to the previous item.
DISPLAY
Finishes browsing and displays the
playback content information.
4
Playback starts.
Play/pause
/ Moves to the next or previous song in the
folder.
Stop
SHUFFLE
Starts shuffle playback (& P.37).
REPEAT
Starts repeat playback (& P.37).
22
• Some USB devices may not work properly even if
they meet the requirements. Playability of and
power supply to all USB devices are not
guaranteed.
En
INPUT
2
• Yamaha and suppliers do not accept any liability
for the loss of data saved on a USB device
connected to the unit. As a precaution, it is
recommended to make backup copies of
important files.
• Stop playback before disconnecting the USB device.
1
• A USB device is automatically charged when it is
connected to the unit, except in the eco standby
mode.
USB
3, 4
Playing back songs in the computer
This unit allows you to play back music files such as MP3, WMA, or FLAC (lossless audio data compression format) files stored in the computer (server) connected to
the network or NAS. Brows the front panel display and select your favorite music file.
• For details on media sharing settings, refer to the
Help of Windows Media Player.
Setting the media
sharing of music files
To play back music files in your computer with this unit,
you need to make the media sharing setting between the
unit and computer (Windows Media Player 11 or later). In
here, setting with Windows Media Player 12 in Windows 7
is taken as an example.
1
2
2
For a PC or a NAS with other DLNA server
software installed
Refer to the owner’s manual of your device or
software and configure the media sharing settings.
Start Windows Media Player 12 on your
PC.
Select “Stream,” then “Turn on media
streaming.”
3
• The control panel window of your PC is shown.
3
4
5
Click “Turn on media streaming.”
Select “Allowed” from the drop-down
list next to the unit's model name.
Click “OK” to exit.
4
En
23
Playing back songs in the computer
• If playback is not possible, check the network
connections and your router settings, and then
connect the unit and the PC to the same network.
Playing back songs in
the PC
1
2
3
Press
repeatedly and select [Server].
Browse and select a song.
S/T
Shows other item.
ENTER/X
Confirm the selected item and
proceed to the next level or start
playback.
HOME
Show the top-level item.
W
Back to the previous item.
DISPLAY
Finish browsing and display the
playback content information.
• The music files in your PC can be preset (& P.39).
1
NET
Playback starts.
Play/pause
/ Move to the next or previous song
in the folder.
Stop
24
SHUFFLE
Starts shuffle playback (& P.37).
REPEAT
Starts repeat playback (& P.37).
En
2, 3
Playing back music via Bluetooth connection
You can listen to sound wirelessly from a Bluetooth compatible device.
• If pairing information for a device is deleted, you
will need to perform pairing of that device again in
order to connect it again.
Pairing a Bluetooth
device with the unit
Bluetooth device
When connecting a Bluetooth device to the unit for the first
time, the device is required to be registered to the unit. This
process is called “pairing.”
Once pairing is completed, subsequent connection can
be made with a couple of easy steps.
A Bluetooth device
connecting for the first
time
A Bluetooth device
already having been
connected
Perform paring and
playing back music (& P.26)
Connecting to Bluetooth
and playing back music
(& P.27)
En
25
Playing back music via Bluetooth connection
Performing pairing and playing back music
1
2
3
Turn on the Bluetooth function on your device.
• If another device is already connected to the unit,
press and hold BLUETOOTH to terminate the
Bluetooth connection, then perform pairing with
the new device.
In the Bluetooth setting of the device, select the unit (network name of the unit).
• You can find the network name in the option
menu.
Press
to set the source to Bluetooth.
• After pairing is complete, the Bluetooth indicator lights up when a Bluetooth connection is established.
• If the device does not connect to the unit automatically after the pairing is completed, select the unit (network name
of the unit) again in the Bluetooth setting on your device.
• For details, see the owner’s manual of your device.
4
26
Play back music on your device.
En
• If a passkey is required during the pairing
operation, enter the number “0000.”
Playing back music via Bluetooth connection
Connecting a paired
Bluetooth device
and playing back music
• Decrease the volume of the amplifier
connected to the unit before playback.
Otherwise, playback volume may be too loud.
1
• If connecting from the unit, the unit searches for the
Bluetooth device connected the last time. In this
case, make sure that device's Bluetooth function is
turned on.
If the unit is connected to another device via Bluetooth
connection, terminate that connection (see “Terminating
the Bluetooth connection” on the right) before
connecting to the target device.
1
Terminating the Bluetooth connection
• Bluetooth connection can be terminated by either
one of the following.
Perform Bluetooth connection.
1, 2
• Connecting from the unit: Press BLUETOOTH.
- Terminate the Bluetooth connection from the
connected device.
- Change to another input source.
• Connecting from the Bluetooth device:
Turn on the Bluetooth function of the connected
device, and select the unit (network name of the
unit) from the available device list.
- Press and hold BLUETOOTH.
- Set the unit to standby mode.
• The Bluetooth indicator lights up when a
connection is established.
2
Play back music on the connected
device.
Indicator
En
27
Playing back music from external devices
This unit allows playback of external devices, such as a DVD player. Use the jacks (DIGITAL IN or AUX IN) according to the device to be connected (& P.5). For the
connection of each external device, refer to its supplied owner’s manual.
1
Unplug the power cable of the unit
and connect the external device to the
unit.
2
• Prepare commercially available cables for
connection.
2
3
Plug the power cable of the unit back
into the wall outlet and press
to
turn the unit on.
3
1
Change the music source.
• Each time you press AUX/DIGITAL, AUX IN
(analog input) and DIGITAL IN (digital input) are
alternately switched.
4
A
Play back the connected external
device.
Stereo
Pin cable
DVD disc player, etc.
Optical
cable
Blu-ray disc player, etc.
• For details on playback, refer to the owner’s
manual supplied with the external device.
• Decrease the volume of the amplifier connected to the unit before connection. Otherwise, playback volume may
be too loud.
28
En
Listening to DAB stations (CD-NT670D only)
You can listen to radio of higher quality sound with Digital Audio Broadcasting (DAB) and DAB+ (upgraded version of DAB).
Connect the supplied antenna (& P.9) and perform an initial scan before you tune into DAB for the first time.
• You can also perform initial scan from the option
setting.
Initial scan
1 Press
Press
repeatedly to select [DAB].
• Initial scan starts automatically when you select [DAB]
for the first time.
• When scanning is complete, the number of receivable
DAB stations is shown on the front panel display
momentarily, and the first station stored in station order
is played.
when the source is DAB.
- Option menu is shown on the front panel
display.
1
TUNER
2 Press S/T to select [Initial Scan] and press
.
- Initial scan starts and finishes automatically.
2
W/X
• If the initial scan is performed, stored DAB station
information and preset DAB stations are cleared.
• This unit can receive only Band III DAB frequencies.
Tuning in DAB stations
1
Press
Frequency in MHz/Channel label
repeatedly to select [DAB].
• When the unit cannot receive the DAB signal, “Off
Air” is shown on the front panel display.
2
Press W/X to select a DAB station.
En
29
Listening to DAB stations (CD-NT670D only)
• To cancel the DAB preset setting, press
Presetting DAB stations
Use the preset function to store your favorite 30 DAB
stations.
1
Tune in a DAB station you want to
preset (& P.29) and press
.
• Preset number flashes on the front panel display.
1
MEMORY
OPTION
.
• You can change the information of the DAB
station shown on the front panel display by
pressing the DISPLAY button. Display switches in
the order as shown below each time you press the
DISPLAY button.
STATION (default)
3
ENTER
2
S/T
DLS (Dynamic Label Segment)
ENSEMBLE
CHANNEL/FREQ (Channel label and frequency)
SIGQ. (signal quality)
AUDIO FORMAT
2
3
Deleting a preset station
Press S/T to select the desired preset
number.
Press
Use the option setting to delete a preset station.
1 Press
when the source is DAB.
- Option menu is shown on the front panel
display.
to completes presetting.
2 Press S/T to select [Preset Delete] and press
.
Selecting preset DAB
stations
1
2
30
3 Press S/T to select the preset number to be
1
TUNER
deleted.
4 Press
.
- A preset station is deleted.
Press
repeatedly to select [DAB].
Press S/T to select a preset station.
En
2
S/T
5 Press
to finish the option setting.
Listening to DAB stations (CD-NT670D only)
• When performing Tune Aid and the DAB signal is
weak, try adjusting the position of the antenna to
obtain good reception.
Confirming the
reception
You can confirm the DAB signal level. This is useful when
you set the antenna.
1
Press
when the source is [DAB].
• Option menu is shown on the front panel display.
2
3
Press S/T to select [Tune Aid] and
press
.
Press S/T to change the channel
label.
• The measured DAB signal reception level is
displayed.
1, 4
OPTION
2, 3
S/T
ENTER
• The level is from 0 (none) to 100 (best).
4
Press
to finish the option setting.
En
31
Listening to the FM radio stations
To play the FM radio, connect the supplied antenna.
See “Connecting antenna” (P.9) for connecting the antenna to the unit.
• If station reception is weak,
you can tune into a station manually by pressing
the W/X button repeatedly.
Tuning in FM stations
1
2
Press
.
Press and hold W/X.
1
• Automatic tuning starts, then stops automatically
when a station is tuned in.
TUNER
2
STEREO
TUNED
W/X
Presetting FM stations
• Auto preset replaces all currently-stored stations
with newly-stored stations.
Auto preset
• You can preset up to 30 FM stations.
1
Tunes in stations with good reception and presets them
automatically.
1
2
3
Press
2, 3
.
MEMORY
Press
more.
Press
and hold for 2 seconds or
.
• Auto preset starts and when it finishes,
“Completed!” is shown on the front panel display.
32
En
TUNER
• To cancel the auto preset, press
.
• You can also preset station automatically from the
option menu (& P.43).
Listening to the FM radio stations
• To cancel manual preset setting, press
Manual preset
1
2
Tune into a station you want to preset
(& P.32).
Press
Deleting a preset station
2
Use the option setting to delete a preset station.
MEMORY
OPTION
1 Press OPTION when the source is FM.
- The option menu is shown on the front panel
display.
.
• Preset number flashes on the front panel display.
.
4
ENTER
3
S/T
- To cancel deleting preset stations, press
OPTION.
2 PressS/Tto select [Preset Delete] and press
ENTER.
3
4
3 Press S/T to select the preset number to
Press
Press
4 Press ENTER.
- The preset station is deleted and [Deleted!] is
shown on the front panel display.
to preset the station.
Selecting preset FM
stations
1
2
be deleted.
Press S/T to select the desired preset
number.
.
Press S/T to select a station.
5 Press OPTION to finish the option setting.
1
TUNER
2
S/T
En
33
Listening to the FM radio stations
• If the signal transmission of the Radio Data System
station is too weak, this unit may not be able to
receive Radio Data System information
completely. In particular, RT (Radio Text)
information uses a lot of bandwidth, so it may be
less available compared to other types of
information.
Radio Data System
(U.K. model only)
The unit can receive Radio Data System information.
Press
when the source is FM.
• Each press of the button changes the information
displays shown below.
PService (Program Service)
PTY (Program Type)
RT (Radio Text)
CT (Clock Time)
Frequency
DISPLAY
34
En
Listening to the Internet radio
You can play back world-wide radio stations via the Internet.
Make sure that the unit is connected to the Internet properly (& P.11).
1
2
• Playback information can be shown by pressing
the DISPLAY button while Internet radio is
played back. Information changes as shown below
each time you press it.
Press repeatedly and select
[NetRadio].
Browse the Internet and select a radio
station.
Radio station name (default)
1
Playing time
NET
Song title
• You can register your favorite Internet radio
stations to the “Bookmarks” folder by accessing
the following website with the web browser on
your PC.
http://yradio.vtuner.com
• The remote control functions are shown below.
3
S/T
Shows other item.
ENTER/X
Confirm the selected item and
proceed to the next level or start
playback.
HOME
Show the top-level item.
W
Back to the previous item.
DISPLAY
Finish browsing and display the
playback content information.
- To use this feature, you need the vTuner ID of
the unit and your e-mail address to create your
personal account. You can check the vTuner ID
in [Network Info] (& P.44) in the option setting.
• The stations of the Internet radio can be preset
(& P.39).
Playback starts.
• To stop playback, press
- Before registering Internet radio stations, play
back any of the Internet radio stations with the
unit.
.
2, 3
En
35
Playing back music with AirPlay
The AirPlay function allows you to play back iTunes/iPod music on the unit wirelessly via a network.
Make sure that the unit and your PC or iPod are connected to the same router (& P.11).
Playing back songs
with iPod
1
2
Turn on the unit and display the
playback screen on the iPod.
• If the iPod recognizes the unit,
the screen of the iPod.
1
• You can also use the unit and remote control to
play back, pause, stop, and skip songs.
iPod iOS7/iOS8
is shown on
Tap
and select the unit (network
name of the unit).
Playing back songs
with iTunes
2
Turn on the unit and start iTunes.
• If the iTunes recognizes the unit,
on the screen of iTunes.
2
CD-NT670 XXXX
• The source automatically switches to [AirPlay]
(except in the eco standby mode).
3
36
Play back songs with iTunes.
En
Example
1
is shown
Click
and select the unit (network
name of the unit).
iPod iOS6
Clearing AirPlay
• The source automatically switches to [AirPlay] and
playback starts (except in the eco standby mode).
1
• For an iPod with iOS7/iOS8 installed, the
indication is displayed within the control center.
To display the control center, swipe the iPod
screen in an upward direction.
Example
2
• Tap/click
on the iPod/iTunes screen and
select a device other than the unit from the
speaker list. Or, change the source to other than
AirPlay.
More on playback
You can enjoy music in varied song order and view music information during playback.
Operations described in this section apply to all devices, such as PC (server), USB device, or CD. The operation for preset registration is available only for network
contents.
Shuffle playback
Press
during playback.
• The shuffle indicator in the front panel display switches
as shown below each time you press the button.
Perform shuffle playback.*
Not displayed Does not perform shuffle playback.
* The range of shuffle depends on the media being played
back.
Repeat playback
Press
during playback.
• The repeat indicator in the front panel display switches
as shown below each time you press the button.
Repeat the song being played back.
REPEAT
SHUFFLE
Perform repeat playback.*
Not displayed Does not perform repeat playback.
* The range of repeat depends on the playback media.
En
37
More on playback
• Characters shown on the front panel display are
alphanumerics only.
Playback information
Song title, elapsed time, etc., can be shown on the front
panel display.
Press
during playback.
AL B U M
M e t eora
• Display switches in the order as shown below each time
you press the button.
USB/AirPlay/
Server
CD
Song title*1
Playing time
Album tile
Remaining time of the
song*2
Artist name
Remaining time of the
disc*2
Playing time
1, 3
Song title* *
Artist name*3
Album tile*3
*1 If the song title cannot be obtained, the file title may be
displayed.
*2 Only when playing an audio CD.
*3 Only when playing an audio CD and when there is
information to display.
38
En
DISPLAY
More on playback
• If the input preset number already has content
registered, the content is overwritten.
Presetting network
contents
• If A is pressed during presetting, the unit enters in
the standby mode and the preset is canceled.
You can preset the network content being played back.
1
• The preset is available for the following sources:
- Internet radio
Press
during the playback of the
network content.
- Server
- Streaming service (may be unavailable for some
areas)
• Start presetting.
2
3
Enter the desired preset number using
the numeric buttons.
Press
to preset the station.
2
• You can set the preset number from 1 to 37.
1, 3
MEMORY
Selecting preset
network content
1
2
Press
.
1
NET
Enter the preset number using the
numeric buttons.
• When the network is connected, the content preset for
the input preset number is played back.
• If the source being used is not the selected content, the
current source is replaced with the selected content.
En
39
More on playback
?
• The operation when the registered FAVORITES
buttons are pressed depends on the input sources
of the registered contents (& P.41).
Presetting music
contents to FAVORITES
You can register your favorite content to the FAVORITES
buttons (A to C) to easily play back the content.
Press and hold any of the FAVORITES
buttons (A to C) during the playback of the
content.
• The content being played back is registered to the
FAVORITES button.
Selecting network
content registered to
FAVORITES
Press the FAVORITES button (A to C) with
the content registered.
• The content is being played is switched to that
registered to the pressed FAVORITES button.
40
En
FAVORITES
(A to C)
More on playback
FAVORITES registration list
Input
sources
Content that can
be registered
What happens when the FAVORITES buttons are
pressed
Server
Songs
The input source is switched and the registered songs
are played back from the first track.
NetRadio
Radio station
The input source is switched and the registered radio
station is played back.
Input source only
The input source is switched.
Bluetooth*
Input source only
The input source is switched.
USB
Songs
The input source is switched and the registered songs
is played back.
AirPlay*1
1
USB DAC*1*2 Input source only
The input source is switched.
CD
Songs
The input source is switched and the registered songs
are played back from the first track.
FM
Radio station
The input source is switched and the registered radio
station is played back.
DAB
(CD-NT670D
only)
Station
The input source is switched and the registered radio
station is played back.
AUX*1
Input source only
The input source is switched.
Digital*1
Input source only
The input source is switched.
*1 To play back the content, you must configure the device for the input source.
*2 Available only when the pre-main amplifier (A-U670) is connected with the system.
En
41
Using the sleep timer
You can set the time to elapse which the unit automatically enters to standby mode.
Press
several times to select the time.
• Time can be selected from 120/90/60/30 min., or OFF.
• The SLEEP indicator lights up when the sleep timer is
set.
• To cancel the sleep timer, press SLEEP again.
SLEEP
42
En
Option settings
Option settings allow you to configure the unit to suit how you will use it.
1
Press
.
• Option menu is shown on the front panel display
(& P.44).
2
3
Select a desired option menu with S/T,
and press
.
Change the setting with S/T, and
press
.
• Repeat step 3 if the sub menu is required to be
set.
1, 4
OPTION
• Press W to cancel the setting and return to the
previous level.
• Repeat steps 2 and 3 if you set another menu
item.
4
Press
to finish the option setting.
2, 3
S/T/W
ENTER
En
43
Option settings
Option menu list
Menu
Sub menu
Default
Function
Preset Delete*1 (& P.33)
Deletes preset stations.
Auto Preset*1
Sets the Auto Preset.
Initial Scan*1,*2 (& P.29)
Scans all receivable frequencies and registers
them in the unit.
Tune Aid*
Network
Info
44
En
1,*2 (& P.31)
Menu
Sub menu
Network
Config
Select Network
System
Config
Default
Wired
Function
Selects a network connection method.
DHCP
On
Enables/disables DHCP.
AutoPowerStdby
On
Sets the unit into standby mode automatically
(& P.10).
Net Standby
On
Sets the eco standby (& P.10).
Bluetooth
On
Sets Bluetooth.
Shows the level of received DAB signal.
Initialize Set
Resets to the factory default settings.
Status
Shows the connection status of the
NETWORK jack.
Version
Shows the firmware version of the unit.
LAN MAC Address
Shows MAC address.
*1 Only when the radio is played back
WiFi MAC Address
Shows MAC address.
*2 CD-NT670D only
Bluetooth Addr
Confirms the Bluetooth address.
MusicCast Info
Shows the information on MusicCast.
SSID
Confirms the SSID.
WiFi Direct Info
Shows the information for WiFi Direct.
Network Name
Shows the name of the unit that appears on
the network.
vTuner ID
Confirms the vTuner ID.
IP Address
0.0.0.0
Confirms the IP address.
Subnet Mask
0.0.0.0
Confirms the subnet mask.
Default Gateway
0.0.0.0
Confirms the default gateway.
DNS Server(P)
0.0.0.0
Confirms the primary DNS server.
DNS Server(S)
0.0.0.0
Confirms the secondary DNS server.
Firmware
Update
Update
Network
Updates the firmware of the unit (& P.45).
Updating the firmware
When a new firmware for the unit is released, a message to update your current firmware will be shown on the front panel display (when the unit is connected to the Internet only).
In this page, an updating method via a network using the option setting is shown.
1
Press
• Do not operate the unit or disconnect the power
cable and network cables while updating.
.
• The option menu is shown on the front panel
display.
2
3
4
• When Internet speed is not fast enough or the unit
is connected to the wireless network via a wireless
network adapter, network update may not be
possible depending on the condition of the
wireless connection. In this case, try again or update
the firmware using a USB memory device. The
firmware can be downloaded from the Yamaha
Website.
Select [Firmware Update] with S/T,
and press
.
Select [Update] with S/T and press
.
Select [Network] with S/T, and press
.
• Press ENTER again, then update starts.
1
OPTION
To update the firmware using a USB memory
device
You can download the firmware to the USB memory
device, and connect that USB memory device to the
USB jack on the unit.
• Select [USB] in step 4 to start the update.
• When update finishes, messages are shown in the
following order: “UPDATE SUCCESS”, “PLEASE ...”,
and “POWER OFF!”
5
Press A on the front panel.
2, 3, 4
S/T
ENTER
• Update is applied.
En
45
Troubleshooting
Refer to the table below when the unit does not function properly. If your problem is not listed below or if the instruction below does not help, turn off the unit,
disconnect the power cable, and contact the nearest authorized Yamaha dealer or service center.
First, check that the connectors of each cable are securely inserted in to jacks on each device. Check also that the power cable is plugged into an outlet.
General
Problem
The unit enters the standby mode soon
after the power is turned on.
The unit does not operate properly.
No sound.
Noise is heard.
The power is suddenly turned off.
There is noise interference from digital or
high-frequency equipment.
The remote control does not work or does
not function properly.
46
En
Cause
Solution
The power cable is not properly connected.
Connect the power cable firmly.
The unit got a strong electric shock from an outside source, such as lighting
or excessive static electricity.
Hold down A on the front panel for more than 10 seconds to initialize and
reboot the unit. (If the problem persists, unplug the power cable from the
wall outlet and plug it again after 30 seconds or more.)
The audio cable connection between this unit and amplifier is improper.
Connect the audio cable firmly. If the problem persists, use another audio
cable (& P.8).
The input setting on the amplifier is incorrect.
Select the correct input (from this unit) on the amplifier.
This unit is too close to the digital or radio-frequency equipment.
Move this unit away from such equipment.
The audio cable between this unit and the media sever is defective.
Connect the audio cable firmly. If the problem persists, use another audio
cable.
The sleep timer may be set (& P.42).
Auto Power Standby function is activated (& P.10).
Turn on the unit and play the source again.
This unit is too close to the digital or high-frequency equipment.
Place this unit farther away from such equipment.
The remote control may be operated outside its operation range.
Operate the remote control within its operation range (& P.10).
The remote control sensor on this unit may be exposed to direct sunlight or
strong lighting such as an inverter type fluorescent lamp.
Change the orientation of lighting or the unit, or location of the unit.
The battery may be worn out.
Replace the batteries with new ones (& P.7).
There are obstacles between the sensor of this unit and the remote control.
Remove the obstacles.
Troubleshooting
Network
Problem
Cause
Solution
The network feature does not function.
The network parameters (IP address) have not been obtained properly.
Enable the DHCP server function of the router. In addition, in the [Network
Config] of the option setting of the unit, set [DHCP] to [On]. If you want to
configure the network parameters manually, check that you are using an IP
address which is not used by other network devices in your network
(& P.44). For details on how to set the router, contact the manufacturer of
the router.
Playback stops (songs cannot be played
back continuously).
There are unsupported files in the server.
Remove the files (including image files or hidden files) which the unit does
not support, from the folder being played back.
The media sharing setting is not correct.
Configure the sharing setting and select the unit as a device to which music
contents are shared (& P.23).
Some security software installed on your PC is blocking the access of the
unit to your PC.
Check the setting of the security software installed in your PC.
The unit and PC are not in the same network.
Check the network connections and your router settings, and then connect
the unit and the PC to the same network.
The files are not supported by the unit or the media server.
Use the file format supported by both the unit and the media server
(& P.54).
The selected Internet radio station is currently not available.
There may be a network problem at the radio station, or the service may
have been stopped. Try the station later or select another station.
The selected Internet radio station is currently broadcasting silence.
Some Internet radio stations broadcast silence at certain of times of the day.
In this case, no sound is output even if the radio waves are received. Try the
station later or select another station.
Access to the network is restricted by the firewall settings of your network
devices (such as the router).
Check the firewall settings of your network devices. The Internet radio can
be played only when it passes through the port designated by each radio
station. The port number varies depending on the radio station.
The dedicated application for mobile
devices does not detect the unit.
The unit and mobile devices are not in the same network.
Check the network connections and your router settings, and then connect
the unit and the PC to the same network.
Update of the firmware via network failed.
The network connection is unstable.
Try updating again after a while. Or update the firmware via USB memory
(& P.45).
The unit does not detect the PC.
The files in the PC cannot be viewed or
played back.
The Internet radio cannot be played.
En
47
Troubleshooting
Problem
The iPod does not recognize the unit
when using AirPlay.
The unit cannot connect to the Internet
via a wireless router (access point).
Wireless network is not found.
Cause
Solution
A multi-SSID supported router is used.
The network separation function of the router may prevent the iPod from
accessing the unit. When connecting an iPod, use SSID that can access the
unit.
The wireless router (access point) is turned off.
Turn on the wireless router (access point).
The unit is placed too far from the wireless router (access point).
Place the unit and the wireless router (access point) closer to each other.
There is an obstacle between the unit and the wireless router (access point).
Place the unit and the wireless router (access point) without any obstacle
between them.
Wireless communication is interrupted by the electromagnetic waves
emitted from a microwave oven or other wireless devices.
When using the unit via wireless connection, place it away from devices
emitting electromagnetic waves.
Access to the network is restricted by the firewall settings of your wireless
router (access point).
Check the firewall setting of the wireless router (access point).
Bluetooth
Problem
Cannot make the unit pair with a
Bluetooth device.
48
En
Cause
Solution
The unit is turned off.
Turn the unit on and perform the paring (& P.25).
The [Bluetooth] of the option setting is set to [Off].
Set it to [On].
Another Bluetooth device is connected.
Terminate current Bluetooth connection, and perform pairing with the new
device.
This unit and the device are too far apart.
Pair the unit and device within a distance of 10 m (33 ft).
There is a device (microwave oven, wireless LAN, etc.) that outputs signals
in the 2.4 GHz frequency band nearby.
Move this unit away from the device that is emitting radio-frequency
signals.
A Bluetooth adapter, etc., that you want to pair with this unit has a passkey
other than “0000.”
Use a device whose passkey is “0000.”
The Bluetooth device does not support A2DP.
Perform pairing with a device which supports A2DP.
Troubleshooting
Problem
Cannot make a Bluetooth connection.
No sound is produced, or the sound is
interrupted during playback.
Cause
Solution
The unit is turned off.
Turn the unit on.
The [Bluetooth] of the option setting is set to [Off].
Set it to [On].
Another Bluetooth device is connected.
Terminate current Bluetooth connection, then establish a connection with
that device again.
The Bluetooth function of the device is turned off.
Turn on the Bluetooth function of the device.
The pairing information has been deleted.
Perform pairing again (& P.25).
This unit can be paired with 20 devices. If pairing with a 21st device is
performed, the pairing information with the earliest connection date will
be deleted.
This unit is not registered on the device’s Bluetooth connection list.
Perform pairing again (& P.25).
The volume of the connecting device is set too low.
Turn up the volume of the connecting device.
The connecting device is not set to send Bluetooth audio signals to the
unit.
Switch the output of Bluetooth audio signals of the connecting device to
the unit.
The Bluetooth connection of the unit with the device has terminated.
Perform Bluetooth connection operations again (& P.25).
There is a device (microwave oven, wireless LAN, etc.) that outputs signals
in the 2.4 GHz frequency band nearby.
Move this unit away from the device that is emitting radio-frequency
signals.
This unit and the connecting device are too far apart.
Move the connecting device to within 10 m (33 ft) of the unit.
The Bluetooth function of the device is turned off.
Turn on the Bluetooth function of the device.
The connecting device is not set to send Bluetooth audio signals to this unit.
Check that the Bluetooth function of the connecting device is set properly.
Disc
Problem
Playback does not start after a disc is set.
Some button operations do not work.
Playback does not start immediately after
pressing
on the unit
or
on the remote control (stops
immediately).
Cause
Solution
The disc set in the unit may not be supported.
Use the disc supported by the unit (& P.53).
The disc may be dirty.
Wipe the disc clean (& P.53).
The disc set in the unit may not be supported.
Use the disc supported by the unit (& P.53).
If the unit was moved from a cold to warm place, condensation may have
formed on the disc reading lens.
Wait for an hour or two until the unit adjusts to the room temperature, and
try again.
En
49
Troubleshooting
USB devices
Problem
The unit does not detect the USB device.
Folders and files in the USB device cannot
be viewed.
Cause
Solution
The USB device is not connected to the USB jack securely.
Turn off the unit, reconnect your USB device, and turn the unit on again
(& P.22).
A USB device in a format other than FAT16/32 format is used.
Use a USB device with FAT16 or FAT32 format.
The data in the USB device is protected by the encryption.
Use a USB device without an encryption function.
DAB reception (CD-NT670D only)
Problem
Cannot tune into any DAB stations.
The initial scan operations are not
successful and [Not Found] is shown on
the front panel display.
Cause
Solution
The initial scan operations were not performed.
Perform the initial scan operations (& P.26).
The DAB signals are too weak.
Use the DAB Tune Aid feature to conform the best position of the antenna
(& P.22).
The positioning of the antenna is not optimal for DAB reception.
There is no DAB coverage in your area.
Check with your dealer or WorldDMB online at http://www.worlddab.org
for a listing of the DAB coverage in your area.
There is noise interference (e.g. hiss,
crackle or jitter)
The antenna needs to be repositioned.
Readjust the position of the antenna (& P.9).
The DAB signals are too weak.
Use the DAB Tune Aid feature to conform the best position of the antenna
(& P.29).
The DAB station information is not shown
or is inaccurate.
The DAB station may be temporarily out of service, or the DAB station
information is not provided by the DAB broadcaster.
Contact the DAB broadcaster.
50
En
Troubleshooting
FM reception
Problem
FM stereo reception is noisy.
Cause
Solution
The antenna is not connected properly.
Make sure the antenna is connected properly and change the position of
the antenna (& P.9).
The radio station you selected may be far from your area, or the antenna
input is poor.
Use a commercially available outdoor antenna. For details, consult a
specialist store.
Use a commercially available outdoor antenna. For details, consult a
specialist store.
Automatic tuning does not work.
The radio station you selected may be far from your area, or the antenna
input is poor.
Cannot select a preset radio station.
The preset (memory) may have been erased.
Preset radio stations again (& P.32,33).
There is distortion, and clear reception
cannot be obtained even with a good FM
antenna or an outdoor antenna.
Multipath reflection or other radio interference may have occurred.
Change the height, direction, or placement of the antenna.
Use the manual tuning method (& P.33).
En
51
Troubleshooting
Messages on the front panel display
Message
Cause
Solution
Access to the PC is denied.
Configure the sharing settings and select the unit as a device to which
music contents are shared (& P.23).
The unit cannot access the USB device.
Turn off the unit and reconnect your USB device. If the problem persists, try
another USB device.
There is a problem with the signal path from the network to the unit.
Make sure your router and modem are turned on. Check the connection
between the unit and your router (or hub) (& P.12).
Initializing
The unit is starting up.
Wait until the message disappears. If the message stays more than 3
minutes, turn off the unit and turn it on again.
Loading...
The unit is loading the specified file/contents.
Wait until the unit finishes loading.
No Content
Selected folder does not contain playable files.
Select a folder with playable files (& P.54).
The disc set in the unit may not be supported.
Use a disc supported by the unit (& P.53).
The disc may be dirty, or foreign objects may be attached to it.
Wipe the disc clean. Alternatively, remove foreign matters adhered to the
disc.
Disc is set upside-down.
Set the disc with the labeled side facing up.
Access Denied
Access Error
No Disc
No Songs
The disc does not contain playable files.
Set a disc with playable files (& P.53).
Not Connected
The unit is not connected to the network.
Check the network connection.
The connected USB device is not supported by the unit.
USB device is not connected properly.
Disconnect the USB device, turn off the unit, and turn it on again. If this
does not solve the problem for the USB device, it is not playable on the unit.
Unable to play
The unit cannot play back the songs stored on the USB devices or the
computer for some reason.
Check if the format of files you are trying to play is supported by the unit
(& P.54).
Version Error
Firmware update is failed.
Update the firmware again.
Over current
52
En
Supported devices/media and file formats
Supported devices/
medias
PCs
Discs
• This unit is designed for use with audio CD, CD-R/RW
(ISO 9660 format) with any of the following logos
printed on the disc or the disc jacket.
Audio CD
NAS
NAS compatible with DLNA version 1.5.
* Discs which bear one of the following.
FOR CONSUMER
FOR CONSUMER USE
FOR MUSIC USE ONLY
• 8-cm discs are playable with this unit.
Set a disc in the inner recessed area of the disc tray.
• Do not connect devices other than the USB mass storage class
devices (USB charger, USB hub, etc.), PCs, card readers, and
external hard discs.
Notes on discs
• USB devices with encryption cannot be used.
• CD-R/RW cannot be played back unless finalized.
Finalization means the process for making a disc to be
ready for playback on a compatible device .
• Depending on the manufacturer or type of the USB
device, the unit may not recognize the USB device or
some functions may be unavailable.
• Use a soft-tipped pen when writing
on the label side of a disc.
• Do not put tape, seal, glue, etc., on a disc.
• Do not set foreign object on the disc tray.
CD-R/RW*
• The unit is compatible with USB mass storage class
devices (e.g., flash memories or portable audio players)
using FAT16/FAT32 format.
• Do not touch the surface of the disc.
Hold a disc by its edge or center hole.
• Do not use a protective cover to prevent scratches.
PC with Windows Media Player 11 or Windows Media
Player 12 installed.
USB devices
Handling discs
• Do not set any other type of disc other than stated
above in this unit. Doing so may damage the unit.
• Do not set more than one disc in this unit at one time.
This could cause damage to both this unit and the discs.
• If a disc becomes dirty, wipe it
with a clean, dry soft cloth from
the center out to the edge. Do not
use record cleaner or paint
thinner.
• Do not use any lens cleaners as
they may cause malfunction.
• Do not expose discs to direct sunlight, high
temperature, high humidity, or dust.
• When a disc is not being used, remove it from this unit
and store in an appropriate case.
• Some discs cannot be played back depending on the
disc characteristics or recording conditions.
• Do not use any non-standard shaped discs such as a
heart-shaped disc.
• Do not use discs with many scratches or a crack on their
surface, or warped/glued discs.
En
53
Supported devices/media and file formats
File format
File format the unit supporting is as follows.
DLNA/USB
Format
Disc
Sampling
frequency
(kHz)
Quantization Bitrate
bitrate (bit)
(kbps)
Number of
channels
Gapless
playback
supported
WAV*
32/44.1/48/
88.2/96/176.4/
192
16/24
-
2
3
MP3
32/44.1/48
-
8-320
2
-
WMA
32/44.1/48
-
8-320
2
-
MPEG-4 AAC
32/44.1/48
-
8-320
2
-
FLAC
32/44.1/48/
88.2/96/176.4/
192
16/24
-
2
3
ALAC
32/44.1/48/
88.2/96
16/24
-
2
3
AIFF
32/44.1/48/
88.2/96/176.4/
192
16/24
-
2
3
* Linear PCM format only
• To play back FLAC files, you need to install server software that supports sharing of FLAC
files via DLNA on your PC or use a NAS that supports FLAC files.
• Digital Rights Management (DRM) files cannot be played back.
54
En
Format
Sampling frequency (kHz)
Quantization bitrate
MP3
8-48
16
WMA
16-48
16
Specifications
Bluetooth
Input
AUX IN
RCA x 1
DIGITAL IN
OPTICAL x 1
Output
ANALOG OUT
RCA x 1
CD
Laser
Bluetooth version
Ver. 2.1+EDR
Supported profile
A2DP (Advanced Audio Distribution Profile)
AVRCP (Audio/Video Remote Control Profile)
Compatible codecs
SBC, AAC
Wireless output
Bluetooth Class 2
Maximum communication range
10 m (33 ft) (without interference)
Wave length
790 nm
Audio
Output power
10 mW
Output level
Media
CD, CD-R/RW
Audio format
Audio CD, MP3, WMA
Frequency
response
ANALOG OUT 2.0±0.3 V
CD
2 Hz to 20 kHz (-3 dB)
Network
Fs 48 kHz: 2 Hz to 24 kHz (-3 dB)
Fs 96 kHz: 2 Hz to 48 kHz (-3 dB)
Fs 192 kHz: 2 Hz to 96 kHz (-3 dB)
USB
Supported file format
MP3, WMA, MPEG4 AAC, WAV, FLAC, ALAC, AIFF
General
Network
Power supply
Interface
100Base-TX/10Base-T
Internet radio
vTuner supported
PC client function
DLNA Ver. 1.5 supported (DMP/DMR function)
Supported file format
Same as USB supported file format
AirPlay
AirPlay supported
Power consumption
16 W
Network standby off
Standby power
consumption
FM
87.5 MHz to 108.0 MHz
DAB (CD-NT670D only)
174 MHz to 240 MHz (Band III)
0.1 W
Wired (Ethernet): 1.7 W
Network standby on
Auto power standby function
Tuner
Tuning range
AC 220 to 240 V, 50/60 Hz
Wireless (Wi-Fi/Wireless Direct/Bluetooth):
1.8 W/1.9 W/1.6 W
No signal input: 20 minutes
No operation: 8 hours
Dimensions (W x H x D)
314 x 70 x 338 mm (12-3/8 x 2-3/4 x 13-1/4 in.)
(With the antenna stood upright)
314 x 142 x 338 mm (12-3/8 x 5-5/8 x 13-1/4 in.)
Weight
2.9 kg (6.5 lbs.)
Specifications are subject to change without notice.
En
55
Trademarks
AirPlay, iPad, iPhone, iPod, iPod touch and iTunes are trademarks of Apple Inc., registered in the
U.S. and other countries.
AirPlay works with iPhone, iPad, and iPod touch with iOS 4.3.3 or later, Mac with OS X Mountain
Lion or later, and Mac and PC with iTunes 10.2.2 or later.
(For CD-NT670D)
The unit supports DAB/DAB+ tuning.
(as of July 2015)
Explanations regarding GPL
DLNA™ and DLNA CERTIFIED™ are trademarks or registered trademarks of Digital Living Network
Alliance. All rights reserved. Unauthorized use is strictly prohibited.
This product utilizes GPL/LGPL open-source software in some sections. You have the right to
obtain, duplicate, modify, and redistribute this open-source code only. For information on GPL/
LGPL open source software, how to obtain it, and the GPL/LGPL license, refer to the Yamaha
Corporation website (http://download.yamaha.com/sourcecodes/musiccast/).
Windows™
Windows is a registered trademark of Microsoft Corporation in the United States and other countries.
Internet Explorer, Windows Media Audio and Windows Media Player are either registered trademarks
or trademarks of Microsoft Corporation in the United States and/or other countries.
The Wi-Fi CERTIFIED Logo is a certification mark of the Wi-Fi Alliance.
Android™
The Wi-Fi Protected Setup Identifier Mark is a mark of the Wi-Fi Alliance.
Android and Google Play are trademarks of Google Inc.
Wi-Fi, Wi-Fi Alliance, Wi-Fi CERTIFIED, Wi-Fi Protected Setup, WPA and WPA2 are trademark or
regitstered trademark of Wi-Fi Alliance.
MusicCast is a trademark or registered trademark of Yamaha Corporation.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and
any use of such marks by Yamaha Corporation is under license.
Bluetooth protocol stack (Blue SDK)
Copyright 1999-2014 OpenSynergy GmbH
All rights reserved. All unpublished rights reserved.
56
En
AVEEA71102A
English
Important Notice: Guarantee Information for customers in EEA* and Switzerland
For detailed guarantee information about this Yamaha product, and Pan-EEA* and
Switzerland warranty service, please either visit the website address below (Printable file is available at our website) or contact the Yamaha representative office for your country.
* EEA: European Economic Area
N et wor k C D Pl ayer
http://europe.yamaha.com/warranty/
O WNER ’S MANUAL
© 2015 Yamaha Corporation
Printed in China ZS21820
AB
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement