null  null
INSTRUCTION MANUAL
DVW-7100
DVD VIDEO PLAYER & 4-HEAD VCR
English
REPRODUCTOR DE DVD VIDEO Y VCR DE
4 CABEZALES
Español
Only cassettes marked
can be used with this DVD+VCR.
As an ENERGY STAR® Partner,
SANYO has determined that
this product or product model
meets the ENERGY STAR®
guidelines for energy efficiency.
SANYO'S HELP-LINE
Call the toll-free number below if you have any difficulties operating this product.
1-800-813-3435 (Weekdays: 7:30 AM - 4:00 PM Central Time)
Please read this manual carefully before connecting your DVD+VCR and operating it for the first time.
Keep the manual in a safe place for future reference.
P/N: (8)3834RV0003Q
(1E05/04)
Safety Precautions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK
OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This lightning flash with arrowhead symbol within an
equilateral triangle is intended to alert the user to
the presence of uninsulated dangerous voltage
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
product.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO
RAIN OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH
WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE
DANS LA BORNE CORRESPONDANTE DE LA PRISE ET
POUSSER JUSQU’AU FOND.
WARNING: Do not install this equipment in a confined space
such as a book case or similar unit.
NOTE TO CATV SYSTEM INSTALLER: This reminder is provided
to call the CATV system installer's attention to Section 820-40 of
the NEC which provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be connected to
the grounding system of the building, as close to the point of cable
entry as practical.
CAUTION:
This DVD+VCR employs a Laser System.
To ensure proper use of this product, please read this owner’s
manual carefully and retain for future reference should the unit
require maintenance, contact an authorized service location.
Use of controls, adjustments, or the performance of procedures other than those specified herein may result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open
the enclosure. Visible laser radiation when open. DO NOT
STARE INTO BEAM.
2
CAUTION: The apparatus should not be exposed to water
(dripping or splashing) and no objects filled with liquids, such
as vases, should be placed on the apparatus.
FCC WARNING: This equipment may generate or use radio
frequency energy. Changes or modifications to this
equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The
user could lose the authority to operate this equipment if an
unauthorized change or modification is made.
REGULATORY INFORMATION: FCC Part 15
This product has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the product is
operated in a residential installation. This product generates,
uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur
in a particular installation. If this product does cause harmful
interference to radio or television reception, which can be
determined by turning the product off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the product and
receiver.
Connect the product into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician
for help.
OTES ON COPYRIGHTS:
It is forbidden by law to copy, broadcast, show, broadcast
via cable, play in public, or rent copyrighted material without
permission.
This product features the copy protection function developed
by Macrovision. Copy protection signals are recorded on some
discs. When recording and playing the pictures of these discs
on a VCR, picture noise will appear.
This product incorporates copyright protection technology that
is protected by method claims of certain U.S. patents and other
intellectual property rights owned by Macrovision Corporation
and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is
intended for home and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
SERIAL NUMBER: The serial number is found on the back of
this unit. This number is unique to this unit and not available to
others. You should record requested information here and
retain this guide as a permanent record of your purchase.
Model No. ____________DVW-7100_____________
Serial No. __________________________________
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNER’S MANUAL.
AND THOSE MARKED ON THE PRODUCT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE.
This product has been designed and manufactured to assure personal safety. Improper use can result in electric
shock or fire hazard. The safeguards incorporated in this product will protect you if you observe the following procedures for installation, use, and servicing.
This product does not contain any parts that can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.
1. Read these instructions. - All these safety and operating instructions should be read before the product is
operated.
2. Keep these instructions. - The safety, operating and
use instructions should be retained for future reference.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
11. Only use attachments/accessories specified by
the manufacturer.
3. Heed all warnings. - All warnings on the product and
in the operating instructions should be adhered to.
4. Follow all instructions. - All operating and use
instructions should be followed.
5. Do not use this apparatus near water. – For example: near a bath tub, wash bowl, kitchen sink, laundry
tub, in a wet basement; or near a swimming pool; and
like.
6. Clean only with dry cloth. – Unplug this product from
the wall outlet before cleaning. Do not use liquid
cleaners.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions. Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over heating. The openings should never be blocked by placing the product
on a bed, sofa, rug or other similar surface. This product should not be placed in a built-in installation such
as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been
adhered to.
12. Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
3
INTRODUCTION
IMPORTANT SAFETY INSTRUCTIONS
Table of Contents
Introduction
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . 2
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . 3
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Before Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Playable Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Notes on Discs . . . . . . . . . . . . . . . . . . . . . . . . . . 6
About Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Display Window. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Preparation
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-13
Connecting an Antenna/Cable TV to DVD+VCR . 11
Basic TV Connections . . . . . . . . . . . . . . . . . . . . 12
Optional, Preferred TV Connections . . . . . . . 12-13
Before Operation - VCR Part . . . . . . . . . . . . . . 14-16
On-Screen Display(OSD) . . . . . . . . . . . . . . . . . . 14
Setting the On-Screen Display . . . . . . . . . . . . . . 14
Setting the VCR Setup Menu . . . . . . . . . . . . . . . 15
Channel Selection . . . . . . . . . . . . . . . . . . . . . . . 15
Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . 16
Before Operation - DVD Part . . . . . . . . . . . . . . 17-20
General Explanation. . . . . . . . . . . . . . . . . . . . . . 17
On-Screen Display . . . . . . . . . . . . . . . . . . . . . . . 17
Initial Settings . . . . . . . . . . . . . . . . . . . . . . . . 18-20
Initial Settings General Operation . . . . . . . . . 18
LANGUAGE. . . . . . . . . . . . . . . . . . . . . . . . . 18
DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
AUDIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
OTHERS . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
LOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Operation
Operation with tape . . . . . . . . . . . . . . . . . . . . . 21-25
Normal Playback . . . . . . . . . . . . . . . . . . . . . . . . 21
Special Effect Playbacks . . . . . . . . . . . . . . . . . . 21
Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Still Picture and Frame-by-Frame Playback . 21
Slow Motion . . . . . . . . . . . . . . . . . . . . . . . . . 21
Ad JUMP (Advertisement Jump). . . . . . . . . . 21
Normal Recording . . . . . . . . . . . . . . . . . . . . . . . 22
Timer Recording . . . . . . . . . . . . . . . . . . . . . . 22-23
Instant Timer Recording . . . . . . . . . . . . . . . . . . . 24
Dubbing and Editing. . . . . . . . . . . . . . . . . . . . . . 24
Copying from DVD to VCR. . . . . . . . . . . . . . . . . 24
Tape Counter Memory Feature. . . . . . . . . . . . . . 25
Additional Information . . . . . . . . . . . . . . . . . . . . 25
Operation with DVD . . . . . . . . . . . . . . . . . . . . . 26-28
Playing DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Playback Setup . . . . . . . . . . . . . . . . . . . . . . 26
General Features . . . . . . . . . . . . . . . . . . . . . 26-27
Moving to another TITLE . . . . . . . . . . . . . . . 26
Moving to another CHAPTER. . . . . . . . . . . . 26
Slow Motion . . . . . . . . . . . . . . . . . . . . . . . . . 26
Still Picture and Frame-by-Frame Playback . 26
Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Repeat. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Repeat A-B . . . . . . . . . . . . . . . . . . . . . . . . . 27
3D Surround . . . . . . . . . . . . . . . . . . . . . . . . 27
Time Search . . . . . . . . . . . . . . . . . . . . . . . . 27
Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Marker Search . . . . . . . . . . . . . . . . . . . . . . . 27
Screen Saver . . . . . . . . . . . . . . . . . . . . . . . . 27
Special DVD Features . . . . . . . . . . . . . . . . . . . . 28
Checking the contents of DVD Video discs: Menus . 28
Title Menu . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Disc Menu . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Camera Angle . . . . . . . . . . . . . . . . . . . . . . . 28
Changing the Audio Language . . . . . . . . . . . 28
Subtitle . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Operation with Audio CD and MP3 Discs . . . . 29-30
Playing an Audio CD and MP3 Discs . . . . . . . . . 29
Notes on MP3 Recordings . . . . . . . . . . . . . . . . . 29
Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Moving to another Track . . . . . . . . . . . . . . . 30
Repeat Track/ All/ Off. . . . . . . . . . . . . . . . . . 30
Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Random . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Repeat A-B . . . . . . . . . . . . . . . . . . . . . . . . . 30
Programmed Playback . . . . . . . . . . . . . . . . . . . . . 31
Programmed Playback with Audio CD
and MP3 Discs . . . . . . . . . . . . . . . . . . . . . . . . . 31
Repeat Programmed Tracks . . . . . . . . . . . . 31
Erasing a Track from Program List . . . . . . . . 31
Erasing the Complete Program List . . . . . . . 31
Reference
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . 32-34
Video Head Cleaning . . . . . . . . . . . . . . . . . . . . . 34
Language Code List . . . . . . . . . . . . . . . . . . . . . . . 35
Country Code List . . . . . . . . . . . . . . . . . . . . . . . . . 36
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
About the symbols for instructions
Indicates hazards likely to cause harm to the unit
itself or other material damage.
Indicates special operating features of this unit.
Indicates tips and hints for making the task easier.
4
Before Use
Playable Discs
Audio CD
3 inch/5 inch (8 cm/12 cm) disc
In addition, this unit can play a CD-R or CD-RW that
contains audio titles or MP3 files.
otes
Depending on the conditions of the recording equipment or the CD-R/RW disc itself, some CD-R/RW
discs cannot be played on the unit.
The unit cannot play discs that contain data other
than MP3 and CD-DA data.
Do not attach any seal or label to either side (the
labeled side or the recorded side) of a disc.
Do not use irregularly shaped CDs (e.g., heartshaped or octagonal). It may result in malfunctions.
Regional code of the DVD+VCR and DVDs
This DVD+VCR is designed and
manufactured for playback of region
1 encoded DVD software. The
region code on the labels of some
DVD discs indicates which type of DVD+VCR can play
those discs. This unit can play only DVD discs labeled 1
or ALL. If you try to play any other discs, the message
“Check Regional Code” will appear on the TV screen.
Some DVD discs may not have a region code label even
though their playback is prohibited by area limits.
1
ALL
ote on DTS-encoded CDs
When playing DTS-encoded CDs, excessive noise may
be exhibited from the analog stereo output. To avoid
possible damage to the audio system, turn down the
volume before playing back such discs, adjust the volume gradually, and keep the volume level low. To enjoy
DTS Digital SurroundTM playback, an external 5.1 channel Digital SurroundTM decoder system must be connected to the digital output of the unit.
Chapter (DVD only)
Sections of a picture or a musical piece that are smaller
than titles. A title is composed of one or several chapters. Each chapter is assigned a chapter number to
enable you to locate the chapter you want. Depending
on the disc, chapters may not be recorded.
Track (audio CD only)
Sections of a musical piece on an audio CD. Each track
is assigned a track number, enabling you to locate the
track you want.
Remote control battery installation
AAA
otes on DVDs
Some playback operations of DVDs may be intentionally fixed by software manufacturers. As this unit plays
DVDs according to disc content designed by the software manufacturer, some playback features of the unit
may not be available or other functions may be added.
Refer also to the instructions supplied with the DVDs.
Some DVDs made for business purposes may not be
played on the unit.
Title (DVD only)
The main film content or accompanying feature content
or music album.
Each title is assigned a title reference number enabling
you to locate it easily.
AAA
DVD
3 inch/5 inch (8 cm/12 cm) disc
Detach the battery cover on the rear of the
remote control, and insert two AAA batteries with the
and
ends aligned correctly.
Caution
Do not mix old and new batteries. Never mix different
types of batteries (standard, alkaline, etc.).
Remote Control Operation Range
Point the remote control at the remote sensor and press
the buttons.
Distance: About 23 ft (7 m) from the front of the
remote sensor
Angle: About 30° in each direction of the front from the
remote sensor
IMPORTANT NOTE:
SPENT OR DISCHARGED BATTERIES MUST BE
RECYCLED OR DISPOSED OF IN A SAFE MANNER
IN COMPLIANCE WITH ALL APPLICABLE LAWS.
FOR DETAILED INFORMATION, CONTACT YOUR
LOCAL COUNTY SOLID WASTE AUTHORITY.
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic” and the double-D symbol are trademarks of
Dolby Laboratories.
DTS and DTS Digital Out are trademarks of Digital Theater
Systems, Inc.
5
INTRODUCTION
Disc-related terms
Before Use (Continued)
Precautions
Handling the unit
When shipping the unit
The original shipping carton and packing materials
come in handy. For maximum protection, re-pack the
unit as it was originally packaged at the factory.
When setting up the unit
The picture and sound of a nearby TV, VCR, or radio
may be distorted during playback. In this case, position
the unit away from the TV, VCR, or radio, or turn off the
unit after removing the disc.
Cleaning discs
Fingerprints and dust on the disc can cause poor picture quality and sound distortion. Before playing, clean
the disc with a clean cloth. Wipe the disc from the center out.
Yes
No
To keep the surface clean
Do not use volatile liquids, such as insecticide spray,
near the unit. Do not leave rubber or plastic products in
contact with the unit for a long period of time. They will
leave marks on the surface.
Do not use strong solvents such as alcohol, benzine,
thinner, commercially available cleaners, or anti-static
spray intended for older vinyl records.
Cleaning the unit
About the
To clean the cabinet
Use a soft, dry cloth. If the surfaces are extremely dirty,
use a soft cloth lightly moistened with a mild detergent
solution. Do not use strong solvents such as alcohol,
benzine, or thinner, as these might damage the surface
of the unit.
To obtain a clear picture
The DVD+VCR is a high-tech, precision device. If the
optical pick-up lens and disc drive parts are dirty or
worn, the picture quality will be poor.
Regular inspection and maintenance are recommended
after every 1,000 hours of use. (This depends on the
operating environment.)
For details, please contact your nearest dealer.
Notes on Discs
Handling discs
Do not touch the playback side of the disc.
Hold the disc by the edges so that fingerprints will not
get on the surface.
Do not stick paper or tape on the disc.
About Symbols
symbol display
“
” may appear on the TV screen during operation.
This icon means the function explained in this owner’s
manual is not available on that specific DVD video disc.
About the disc symbols for instructions
A section whose title has one of the following symbols are
applicable only to those discs represented by the symbol.
DVD DVDs
CD
Audio CD
MP3 MP3 Discs
Setting the Output Source
You must select one of your output sources (DVD or
VCR) to view on the TV screen.
• If you want to view output source of DVD deck:
Press DVD on the remote control or DVD/VCR on the front
panel until DVD indicator in the display window lights and
output source of DVD deck is viewed on the TV screen.
• If you want to view output source of VCR deck:
Press VCR on the remote control or DVD/VCR on the front
panel until VCR indicator in the display window lights and
output source of VCR deck is viewed on the TV screen.
ote
• If you insert a disc while the DVD+VCR is in the VCR
Storing discs
After playing, store the disc in its case.
Do not expose the disc to direct sunlight or sources of
heat, or leave it in a parked car exposed to direct sunlight, as there may be a considerable heat build-up
inside the car.
6
mode, the DVD+VCR will switch to DVD mode
automatically.
• If you insert a cassette tape without an erasure
prevention tab intact while the DVD+VCR is in the
DVD mode, the DVD+VCR will switch to VCR mode
automatically.
Front Panel
DVD/VCR SELECT (output select)
Select one of your output sources to
view on the TV screen between DVD
and VCR.
AV INPUT (VIDEO IN/AUDIO IN)
Connect the audio/video output of an external source (Audio system, TV/Monitor,
Another VCR).
Disc Tray (DVD deck)
Insert a disc here.
INTRODUCTION
POWER
Switches the DVD+VCR ON and OFF.
Cassette Compartment
(VCR deck)
Insert a video cassette here.
B)
PLAY (B
Starts playback of a disc or tape.
Display window
Shows the current status of the
DVD+VCR.
Remote Sensor
Point the DVD+VCR
remote control here.
VCR indicator
Indicates the active VCR
deck.
Z)
EJECT(Z
Ejects the tape in the
VCR deck.
DVD indicator
Indicates the active DVD deck.
Z)
OPEN/CLOSE (Z
Opens or closes the disc tray.
z)
REC (z
To record normally or to activate Instant Timer
Recording.
X)
PAUSE/STILL(X
Pause playback temporarily/press
repeatedly for Frame-by-Frame playback.
x)
STOP (x
Stops playback of the disc or tape.
FF(M)
DVD: Go to NEXT chapter/track. Press
and hold for a fast forward search.
VCR: Advances the tape from STOP
mode or for fast forward picture
search.
REW (m)
DVD: Go to beginning of current
chapter/track or to previous chapter/track.
Press and hold for a fast reverse search.
VCR: Rewinds the tape from STOP mode or
for fast reverse picture search.
V/v)
CHANNEL (V
To scan up or down through memorized channels.
Child Lock
The control buttons on the front panel of the
DVD+VCR can be switched off so that your
DVD+VCR can only be operated using the
remote control.
Press SAFE on the remote control to enable
LOCK function, SAFE and
appear in the
display window.
To disable the LOCK function, press SAFE on
the remote control until OFF appears in the
display window.
7
Display Window
The DVD deck is selected.
A disc is in the DVD deck.
(Lights when a disc is in the DVD deck
and Flashes when no disc.)
Indicates when the Progressive scan is active.
Indicates repeat mode.
Indicates when the DVD+VCR is locked.
DVD+VCR is in timer recording or a timer
recording is programmed.(VCR part only)
A cassette is in the VCR deck.
The VCR deck is selected.
DVD
[P]
VCR
REC
PM
TV
Lights when TV mode is active (See page 22.)
Indicates PM time. (AM is not displayed.)
DVD+VCR is Recording.
(VCR part only)
Indicates total playing time, elapsed time, remaining time or
current deck status (Playback, Pause, etc).
8
Remote Control
POWER
Switches DVD+VCR ON and OFF.
TV/VCR
To view channels selected by the VCR
tuner or by the TV tuner.
DISPLAY, CLK/CNT
Accesses On-Screen display.
Switches among the clock, tape counter
and tape remaining modes on the display.
b/B/v/V (left/right/up/down)
- Selects an option in the menu
- CH/TRK (v/V): Selects channel of VCR.
Adjusts manually the tape’s picture
onscreen.
SETUP, MENU
Accesses or removes DVD setup menu
and VCR menu.
TITLE
Displays the disc’s Title menu, if
available.
X)
PAUSE/STEP (X
Pauses playback or recording.
Presses repeatedly for
frame-by-frame playback.
x)
STOP (x
Stops playback.
z)
REC (z
Records normally or activates Instant
Timer Recording.
0-9 number buttons
Selects numbered options in a menu.
AUDIO
Selects an audio language (DVD).
SUBTITLE
Selects a subtitle language.
MARKER
Marks any point during playback.
SEARCH
Displays MARKER SEARCH menu.
REPEAT
Repeat chapter, track, title, all.
Z)
OPEN/CLOSE, EJECT (Z
- Opens and closes the disc tray.
- Ejects the tape in the VCR deck.
SELECT/ENTER ( )
- Acknowledges menu selection.
- Displays functions on the TV screen.
This button is not available.
DISC MENU
Shows DVD disc menu.
INPUT
To select the VCR deck’s source (Tuner,
LINE 1, or LINE 2).
>)
FORWARD (>
DVD; Search forward*/go to next chapter or track.
VCR; Advances the tape during the
STOP mode or for fast forward picture
search.
H)
PLAY (H
Starts playback.
.)
BACKWARD (.
DVD; Search backward*/go to beginning
of current chapter or track or go to previous chapter or track.
VCR; Rewinds the tape during the
STOP mode or for fast reverse picture
search.
* Press and hold button for about two
seconds.
PROGRAM
Shows or hides Program menu.
CLEAR
Clears a track number from the
program menu or a mark on the
MARKER SEARCH menu.
SAFE
Switch the Lock function on and off.
ANGLE
Selects a DVD camera angle if
available.
RETURN (O)
Removes the setup menu.
ZOOM
Enlarges DVD video image.
RANDOM, Ad JUMP
- Plays tracks in random order.
- Fast forwards picture search through
30 seconds of recording.
A-B, SP/SLP
- Repeats in sequence.
- Selects recording speed
ote
This remote control uses the same buttons for VCR and DVD
functions (ex. PLAY).
When using a VCR, first press the VCR button.
When using a DVD, first press the DVD button.
9
INTRODUCTION
DVD/VCR select button
Selects the output source (DVD or VCR)
to view on the TV screen.
Rear Panel
VCR IN LINE 1 (VIDEO IN/AUDIO IN)
Connect the audio/video output of an external source (Audio system,
TV/Monitor, Another VCR).
DVD/VCR OUT (VIDEO/AUDIO (Left/Right))
Connect to a TV with video and audio inputs.
COMPONENT/PROGRESSIVE SCAN VIDEO OUT (Y Pb Pr) (DVD OUT)
Connect to a TV with Y Pb Pr inputs.
AUDIO OUT (Left/Right) (DVD OUT)
Connect to a TV, amplifier, receiver, or stereo system.
AC Power Cord
Plug into the power source
(AC 120V, 60 Hz).
S-VIDEO OUT (DVD OUT)
Connect to a S-Video Input on TV.
DIGITAL AUDIO OUT (COAXIAL) (DVD OUT)
Connect to digital (coaxial) audio equipment.
ANT.IN (ANTENNA INPUT)
Connect the VHF/UHF/CATV antenna to this terminal.
RF. OUT(DVD/VCR OUT)
Connect to a TV with RF coaxial inputs.
Do not touch the inner pins of the jacks on the rear
panel. Electrostatic discharge may cause permanent
damage to the unit.
10
Connections
Without Cable Box
Depending on your TV and other equipment you wish to
connect, there are various ways you could connect the
DVD+VCR. Use connections described on pages 11-13.
Please refer to the manuals of your TV, VCR, Stereo
System or other devices as necessary to make the best
connections.
For better sound reproduction, connect the DVD+VCR’s
DVD/VCR AUDIO OUT jacks to the audio in jacks of your
amplifier, receiver, stereo or audio/video equipment. See
Optional, Preferred TV Connections on pages 12-13.
Caution
Make sure the DVD+VCR is connected directly to the TV.
Tune the TV to the correct video input channel.
Do not connect the DVD+VCR’s DVD/VCR AUDIO OUT
jacks to the phono in jack (record deck) of your audio
system.
Do not connect your DVD+VCR via your VCR. The DVD
image could be distorted by the copy protection system.
Connecting an Antenna/Cable TV
to DVD+VCR
the antenna leads from the rear of the
1 Disconnect
TV.
the type of cable from your antenna. If it is
2 Identify
a round cable as illustrated, it is a 75 ohm coaxial
antenna cable. This cable will connect directly to
If your cable wire is connected to your TV without a converter
or descrambler box, unscrew the wire from your TV and attach
it to the ANT.IN jack on the DVD+VCR. Use the supplied round
coaxial cable to connect between the DVD+VCR’s RF.OUT
jack and the 75 ohm antenna input jack on the TV. With this
connection, you can receive all midband, super band, and
hyperband channels.
With Cable Box
If a converter is required in your cable system, follow the
instructions below:
The cable hookup permits both TV and DVD+VCR operation.
To view or record CATV channel
1 Tune the TV to the DVD+VCR output channel (CH 3 or 4).
2 Set the DVD+VCR channel selector to the output channel of
the Cable Converter box by pressing the CH/TRK (v/V) or
number (0-9) of your DVD+VCR. (Example: CH3)
3 Select the channel to view at the Cable Converter Box.
otes
With this connection, you CANNOT record one program
while viewing another.
If you are using a cable box to tune channels, it is not necessary to do Auto Channel Programming as indicated on
page 15.
Cable TV
Wall Jack
Back Panel of
Typical Cable Box
the jack marked ANT.IN on your DVD+VCR.
ip
If your antenna lead wire is a flat type antenna cable,
connect it to a Antenna Adaptor (300-ohm to 75-ohm)
(not supplied) and slip the Adaptor onto the ANT.IN
jack. The Adaptor does not screw on to the DVD+VCR,
it just slips over the jack.
Antenna
Antenna
Cable TV
Wall Jack
Flat Wire
(300 ohm)
Rear of DVD+VCR
300/75 ohm
Adaptor
(Not supplied)
OR
OR
Rear of DVD+VCR
11
PREPARATION
ips
Connections (Continued)
Basic TV Connections
Make one of the following connections, depending on
the capabilities of the equipment to be connected.
RF coaxial connection
Connect the RF.OUT jack on the DVD+VCR to the
antenna in jack on the TV using the 75-ohm Coaxial
Cable supplied (R).
ote
If you use this connection, tune the TV to the
DVD+VCR’s RF output channel (CH 3 or 4).
How to set the DVD+VCR’s RF output channel
1. Set the TV to the VCR channel (3 or 4) depending
upon the selected channel.
2. When the DVD+VCR is turned off, press and hold
CHANNEL (V/v) on the front panel for more than five
seconds.
Optional, Preferred TV Connections
ote
You can ONLY watch and listen to DVD playback
through the connections shown below.
S-Video connection
the S-VIDEO OUT jack on the DVD+VCR
1 Connect
to the S-Video in jack on the TV using the optional
S-Video cable (S).
the Left and Right AUDIO OUT jacks of
2 Connect
the DVD+VCR to the audio left/right in jacks on the
TV using the supplied audio cables (A2).
Component Video (Color Stream®) / Progressive
Scan (ColorStream® pro) connection
It will turn itself on and “RF03” or “RF04” appears in the display window.
3. Press CHANNEL (V/v) on the front panel or CH/TRK
(v/V) on the remote control to change the RF output
channel (CH 03 or CH 04).
4. Turn off the DVD+VCR.
1
If your television is a high-definition or “digital ready”
television, you may take advantage of the
DVD+VCR’s progressive scan output for the highest
video resolution possible.
If your TV does not accept the Progressive Scan format, the picture will appear scrambled if you try
Progressive Scan on the DVD+VCR.
Audio/Video connection
1
Connect the DVD/VCR VIDEO OUT jack on the
DVD+VCR to the video in jack on the TV using the
supplied video cable (V).
the Left and Right DVD/VCR AUDIO OUT
2 Connect
jacks on the DVD+VCR to the audio left/right in
jacks on the TV (A1) using the supplied audio
cables.
ote
If you use this connection, set the TV’s source selector
to VIDEO.
Rear of TV
ANTENNA
INPUT
R
A1
VIDEO
INPUT
COMPONENT VIDEO INPUT
Pr
R
V
Rear of DVD+VCR
12
otes
Set the Progressive Scan to “On” on the setup menu
for progressive scan signal, see page 18.
When you use Component Video signal, set the
Progressive Scan to “Off” on the setup menu.
Progressive scan does not work with the analog video
connections (yellow VIDEO OUT jack).
Rear of TV
AUDIO INPUT
L
2
Connect the COMPONENT / PROGRESSIVE
SCAN VIDEO OUT jacks on the DVD+VCR to the
corresponding in jacks on the TV using an optional
Y Pb Pr cable (C).
Connect the Left and Right AUDIO OUT jacks of
the DVD+VCR to the audio left/right in jacks on the
TV (A2) using the supplied audio cables.
Pb
Y
C
Rear of DVD+VCR
S-VIDEO
INPUT
AUDIO INPUT
R
L
A2
S
Connections (Continued)
Optional, Preferred TV
Rear of DVD+VCR
Connections (Continued)
ote
You can ONLY listen to DVD playback using COAXIAL
(X) and AUDIO OUT (A2) connections. The tuner and
VCR will still be heard through the RF.OUT (R) or
DVD/VCR AUDIO OUT (A1) jacks. (See page 12.)
A1
A2
X
PREPARATION
Connecting to an amplifier equipped with two
channel analog stereo or Dolby Surround
Connect the Left and Right AUDIO OUT (or DVD/VCR
AUDIO OUT) jacks on the DVD+VCR to the audio left
and right in jacks on your amplifier, receiver, or stereo
system using the audio cables (A1, A2) supplied.
L
Connecting to an amplifier equipped with two
channel digital stereo (PCM) or to an Audio/Video
receiver equipped with a multi-channel decoder
(Dolby Digital™, MPEG 2, or DTS)
1
Connect one of the DVD+VCR’s DIGITAL AUDIO
OUT jacks (COAXIAL X) to the corresponding in
jack on your amplifier. Use an optional digital
(coaxial X) audio cable.
will need to activate the DVD+VCR’s digital
2 You
output. (See “AUDIO” on page 19).
R
AUDIO INPUT
COAXIAL
DIGITAL INPUT
Amplifier (Receiver)
Accessory Audio/Video (A/V) Connections to
DVD+VCR
Connect the VCR IN LINE 1 or AV INPUT jacks on the
DVD+VCR to the audio/video out jacks on your
accessory component, using the optional audio/video
cables. (Refer to page 24 for “Dubbing and Editing”.)
ip on Digital Multi-channel sound
A digital multi-channel connection provides the best
sound quality. For this you need a multi-channel
Audio/Video receiver that supports one or more of the
audio formats supported by your DVD+VCR (MPEG 2,
Dolby Digital and DTS). Check the receiver manual and
the logos on the front of the receiver.
Caution:
Due to the DTS Licensing agreement, the digital output
will be in DTS digital out when DTS audio stream is
selected.
otes
If the audio format of the digital output does not match
the capabilities of your receiver, the receiver will
produce a strong, distorted sound or no sound at all.
Six Channel Digital Surround Sound via digital
connection can only be obtained if your receiver is
equipped with a Digital Multi-channel decoder.
To see the audio format of the current DVD in the
on-screen display, press AUDIO.
13
Before Operation - VCR Part
On-Screen Display (OSD)
Some of these functions will be displayed every time the
VCR is operated.
❶
❷
❸
PLAY
SP
CH 4
OCT 8 , FRI
❹
❶ TAPE SPEED DISPLAY
2:15 PM
❺
Shows the current tape speed.
❷ FUNCTION DISPLAY
Indicates the current function.
❸ CHANNEL DISPLAY
Indicates the selected channel (or LINE1, LINE2).
❹ DATE DISPLAY
Shows the current date. (Month/Date/Day of the week
format)
EASY INFORMATION
If the Extended Data Service (XDS) signals are provided
along with normal TV signal in your area or during playback of a tape recorded with Extended Data Service
(XDS) signals, the station ID, program title and program
details are shown in the TV screen.
When viewing a channel with Extended Data Service
(XDS) signals, press SELECT/ENTER ( ) then the station ID will appear on the TV screen. Press
SELECT/ENTER ( ) again and the program details will
appear on the TV screen. When viewing a tape recorded with Extended Data Service (XDS) signals, press
SELECT/ENTER ( ) twice then the program title and
program details will appear on the TV screen.
PROGRAM DETAILS
LENGTH: Indicates the run length of a program.
TIME REMAINING: Indicates the remaining time of a
program.
RATING: Indicates the rating of the current program
(N/A, G, PG, PG-13, R, NC-17, X and Not Rated). The
rating N/A means that the motion picture ratings are not
applicable to this program.
CH 4
SP
❺ CLOCK/COUNT/REMAIN DISPLAY
WABC
Shows the current time, the tape counter and remaining time
on the tape.
Each press of the SELECT/ENTER ( ) changes the TV
screen in the following sequence.
STOP
SP
CH 4
“Home video”
OCT 8 , FRI
2:15 PM
Easy Information Screen
(Station ID)
PROGRAM DETAILS
“Home video”
LENGTH 01:00
TIME REMAINING 00:26
RATING N/A
Easy Information Screen
(Program details)
Setting the On-Screen Display
OCT 8 , FRI
The SETUP, clock setting, and timer recordings are
accessed conveniently with On-Screen Menu Displays
that lead you through each step. The following pages
describe the On-screen selections to be set.
2:15 PM
2:15 PM
0:35:40
REM 1:58
otes
The function displays can be seen displayed on the TV
screen for 5 seconds.
The clock (or tape counter, tape remaining) mode will continue until you press SELECT/ENTER ( ).
The tape counter and the remaining tape length indicator
appear only when a cassette is inserted. Also, the remaining
tape length indicator appears after any tape operation.
Menu Selection
Your VCR allows remote control adjustment of several
features.
Press MENU and the MAIN menu will appear.
1
Select the desired menu with v/V button and
2 then
press SELECT/ENTER ( ).
ote
Menus remain on-screen for 3 minutes.
MAIN MENU
CLOCK SET (page 16)
PROGRAM (page 22)
TUNING (page 15)
SETUP (page 15)
14
3 Press MENU when finished.
Before Operation - VCR Part (Continued)
Setting the VCR Setup Menu
1 Press MENU and the MAIN menu will appear.
v/V
V to select the SETUP menu, then
2 Press
press SELECT/ENTER ( ).
v/V
V to choose the AUTO CHANNEL SET
4 Press
B to set the channel.
option, then press b/B
• The tuner will automatically cycle through all
available channels (TV/CATV) in the area and
place them in the tuner’s memory.
• After the AUTO CHANNEL SET is complete, the
TUNING menu will hide and return to the TV
screen automatically.
The SETUP menu will appear.
v/V
V to choose an option from the SETUP
3 Use
B to choose a setting.
menu, then use b/B
FUNCTION OSD
The on-screen display of this DVD+VCR can be turned on or
off.
FUNCTION OSD can be switched between ON and OFF by
pressing b/B.
4 Press MENU when finished.
• TV : If you are using a standard antenna to
receive channels.
CATV : If you are using basic cable to receive
channels.
• Change the setting of TUNING BAND to check the
TV channels.
v/V
V) on the remote control or
CH/TRK (v
6 Use
V/v) on the front panel to cycle the
CHANNEL (V
DVD+VCR through the channels in memory.
TO ADD OR ERASE CHANNELS FROM MEMORY
This feature allows you to add or erase channels from
memory manually.
Channel Selection
1
This DVD+VCR is equipped with a frequency
synthesized tuner capable of receiving up to 181
channels. These include VHF channels 2-13, UHF
channels 14-69 and CATV channels 1-125.
Press V to choose the CH. ADD/DEL option on the
TUNING menu. Press b/B to select a channel to
add or erase.
2
Press SELECT/ENTER ( ) to add or erase the
channel.
Repeat steps 1 and 2 to add or erase channels.
3
Press MENU to return to the TV screen.
Preparation:
Connect the DVD+VCR to the desired type of antenna or
cable TV system, as shown in Connecting Antenna/Cable TV
to DVD+VCR on page 11.
AUTO CHANNEL PROGRAMMING
1 Press MENU and the MAIN menu will appear.
v/V
V to select the TUNING menu, then
2 Press
press SELECT/ENTER ( ).
The TUNING menu will appear.
V to choose the SOURCE SELECT option,
3 Press
B to select TUNER.
then press b/B
Press b/B repeatedly to switch among TUNER, LINE1
and LINE2.
15
PREPARATION
sure the TUNING BAND is set appropriate5 Make
ly (TV or CATV).
Before Operation - VCR Part (Continued)
Setting the Clock
The DVD+VCR gives you two ways to set the time and
date: the Auto Clock Feature or manually. The Auto
Clock Feature enables the DVD+VCR to set the clock
when the DVD+VCR is turned off.
Things to know before starting
The clock uses the 12-hour system. (Be sure to set AM or
PM correctly.)
The initial Clock Setting is JANUARY 1, 2004, 12:00 AM.
Auto Clock Set
The Auto Clock Set feature is set to ON at the factory. In the
ON setting, the DVD+VCR looks for a channel carrying XDS
(Extended Data Services) information. XDS updates the clock
using the Coordinated Universal Time.
ote
There are cases where the TV station does not send, or sends
wrong date and/or time information and the DVD+VCR sets the
incorrect time.
If this happens we recommend that you set the clock manually.
Manual Clock Set
Example: JULY 5, 2004 ; 2:15 AM
1 Press MENU and the MAIN menu will appear.
v/V
V to choose the CLOCK menu.
2 Press
Press SELECT/ENTER ( ) and the CLOCK
menu will appear.
The Auto Clock Feature enables the DVD+VCR to set up
the clock when the DVD+VCR is turned off.
1 Press MENU and the MAIN menu will appear.
v/V
V to choose the CLOCK menu.
2 Press
Press SELECT/ENTER ( ) and the CLOCK
menu will appear.
3 Press b/BB to choose the month.
V to choose the DAY option.
4 Press
B to choose the day.
Use b/B
The day of the week will display automatically.
V to choose the AUTO CLOCK SET option.
3 Press
B to choose ON.
Press b/B
The Auto Clock Set feature is set to ON at the factory. In
the ON setting, the DVD+VCR looks for a channel
carrying XDS (Extended Data Services) information. XDS
updates the clock using the Coordinated Universal Time.
Press
4 item.
Press
E
to choose the DAYLIGHT SAVINGS
F
/
G
to choose the TIME ZONE item.
/ G to choose the correct time zone
(AUTO, EASTERN, CENTRAL, MOUNTAIN,
PACIFIC, ALASKA, or HAWAII).
Press
F
/
G
to choose AUTO, ON or OFF.
If you choose AUTO, the VCR sets the clock using the
DST information broadcast in the signal (channel).
If you choose ON, the VCR sets the clock when the
Daylight Savings Time is started and ended.
2004
E
F
If “AUTO” is selected as the time zone, the VCR sets the
clock using the first Coordinated Universal Time information when it finds in a broadcast signal.
6
off the DVD+VCR and the auto clock
7 Turn
setting works.
Press MENU when finished.
16
E
to choose AUTO, ON or OFF.
If you choose AUTO, the VCR sets the clock using the
DST information broadcast in the signal (channel).
If you choose ON, the VCR sets the clock when the
Daylight Saving Time is started and ended.
Press
5 Press
V to choose the YEAR option.
5 Press
B to choose the year.
Use b/B
Press V to choose the TIME option.
6 Use b/BB to choose the time.
Press to choose the DAYLIGHT SAVINGS
7 item.
8 Press MENU when finished.
ote
If setting the clock manually, “AUTO CLOCK SET” must
be set to “OFF”.
If set to “ON”, an incorrect date and/or time will be
entered again when the DVD+VCR is turned off.
Before Operation - DVD Part
Caution:
Before using the remote control, press the DVD button
to select the device to be operated.
b/B to change the setting of an item.
3 Use
The number buttons can also be used for setting
numbers (e.g., title number). For some functions,
press SELECT/ENTER ( ) to execute the setting.
Temporary Feedback Field Icons
This manual gives basic instructions for operating the
DVD+VCR. Some DVDs require specific operations or
allow only limited operations during playback. When this
occurs, the symbol
appears on the TV screen, indicating that an operation is not permitted by the
DVD+VCR or is not available on the disc.
On-Screen Display
General playback status can be displayed on the TV
screen. Some items can be changed on the menu.
On-screen display operation
1 Press DISPLAY during playback.
Use v/V to select an item.
2 The
selected item will be highlighted.
Title
Chapter
A-B
Off
Repeat Title (DVD)
Repeat Chapter (DVD)
Repeat A-B
Repeat Off
Resume play from this point
Action prohibited or not available
otes
Some discs may not provide all of the features on the
on-screen display example shown below.
If no button is pressed for 10 seconds, the on-screen
display disappears.
You can change the desired status only when “b B”
mark appears on the On-screen display menu item.
DVD
Items
Function (Use v/V to select desired item)
Title Number
1/3
Chapter Number
1 / 12
Time search
Audio language
and Digital Audio
Output mode
Subtitle language
Angle
Sound
-:--:--
1 ENG
D
3/2.1 CH
ABC
1 ENG
1/1
Normal
Selection Method
Shows the current title number and total number of
titles, and skips to the desired title number.
b / B, or Numbers,
SELECT/ENTER ( )
Shows the current chapter number and total number of
chapters, and skips to the desired chapter number.
b / B, or Numbers,
SELECT/ENTER ( )
Shows the elapsed playing time, and
searches the point by the elapsed time directly.
Numbers,
SELECT/ENTER ( )
Shows the current audio soundtrack language,
encoding method, and channel number, and
changes the setting.
Shows the current subtitles language, and
changes the setting.
Shows the current angle number and total number of
angles, and changes the angle number.
Shows the current sound mode, and
changes the setting.
b / B, or
AUDIO
b / B, or
SUBTITLE
b / B, or
ANGLE
b/B
17
PREPARATION
General Explanation
Before Operation - DVD Part (Continued)
Initial Settings
Disc Language (Audio, Subtitle, Menu)
In this menu system, there are several ways to customize the settings provided. Most menus consist of
three levels to set up the options, but some require
greater depth for the variety of settings. If you press
SETUP, only the first level of the menu system will
appear on the TV screen. The second and third level
can be displayed by pressing B. For navigating the
menu levels, you will see “ B ” on the right side of the
menu label to help you to go to the next level.
DVD
Select a language for the disc’s Audio, Subtitle, and
Menu.
Original : The original language set for the disc is selected.
Other : To select another language, press number buttons to
enter the corresponding 4-digit number according to the language code list on page 35. If you enter the wrong language
code, press CLEAR.
DISPLAY
DISPLAY
To bring up and exit the Menu:
Press the SETUP to bring up the menu. The second
press of SETUP will take you back to initial screen.
TV Aspect
16 : 9
Display Mode
Widescreen
Progressive Scan
Off
To go to the next level:
Press B on the remote control.
Move
To go back to the previous level:
Press b on the remote control.
TV Aspect
Initial Settings General Operation
1
Press SETUP.
The setup menu appears. The screen will show the
current setting for the selected item.
2 Use v/V to select the desired item.
the desired item is selected, press B to
3 While
move to the second level.
4 Use v/V to select the second desired item.
5 Press B to move to the third level.
v/V to select the desired setting then
6 Press
press SELECT/ENTER ( ) to confirm your selec7
tion.
Some items require additional steps.
Press SETUP to exit the setup menu.
LANGUAGE
LANGUAGE
Menu Language
English
Disc Audio
Original
Disc Subtitle
Off
Disc Menu
Original
Move
Select
Menu Language
Select a language for the VCR and DVD’s setup menu
and information display.
18
Select
DVD
4:3: Select when a standard 4:3 TV is connected.
16:9: Select when a 16:9 wide TV is connected.
Display Mode
DVD
The Display Mode setting works only when the TV
Aspect mode is set to “4:3”.
Letterbox: Displays theatrical images with masking
bars above and below the picture.
Panscan: Select when a conventional TV set is connected. The video material formatted in the Pan & Scan
style is played back in that style (Both sides of the picture are cut off).
Progressive Scan
DVD
Progressive Scan Video provides the highest quality
pictures with less flickering. If you are using the COMPONENT/PROGRESSIVE SCAN VIDEO OUT jacks,
but are connecting the DVD+VCR to a standard (analog) television, set Progressive Scan to Off. If you are
using the Component Video jacks for connection to a
TV or monitor that is compatible with a progressive
scan signal, set Progressive Scan to On.
Caution
• Once the setting for progressive scan output is
entered, the message appears. Use b/B button to
select “Enter” and press SELECT/ENTER ( ) button.
An image will be visible only on a progressive scan
compatible TV or monitor. If you set Progressive Scan
to ON in error, you must reset the DVD+VCR. First,
remove the disc in the DVD+VCR. Next, press STOP
(x) and hold it for five seconds before releasing it.
The video output will be restored to the standard setting, and a picture will once again be visible on a conventional analog TV or monitor.
• Do not turn off this DVD+VCR while the "PROGRESSIVE SCAN MODE" message is displayed in the TV
screen.
Before Operation - DVD Part (Continued)
AUDIO
Dynamic Range Control (DRC)
Each DVD disc has a variety of audio output options.
Set the player’s Audio Output according to the type of
audio system you use.
AUDIO
Bitstream
DTS
Bitstream
MPEG
PCM
Sample Freq.
48 kHz
DRC
On
Vocal
On
Vocal
Set Vocal to “On” only when a multi-channel karaoke
DVD is playing. The karaoke channels on the disc will
mix into normal stereo sound.
Move
Select
Dolby Digital
Bitstream: Select “Bitstream” if you connected the DVD
Player’s DIGITAL OUT jack to a Dolby Digital decoder
(or an amplifier or other equipment with a Dolby Digital
decoder).
PCM: Select when connected to a two-channel digital
stereo amplifier. DVDs encoded in Dolby Digital will be
automatically downmixed to two-channel PCM audio.
OTHERS
The Auto Play setting can be changed.
OTHERS
AutoPlay
Off
DTS
Bitstream: Select “Bitstream” if you connected the DVD
Player’s DIGITAL OUT jack to a DTS decoder (or an
amplifier or other equipment with a DTS decoder).
Off: If you select “Off”, the DTS signal through the DIGITAL OUT jack is not outputted.
MPEG
Bitstream: Select “MPEG” if you connected the DVD
Player’s DIGITAL OUT jack to a MPEG decoder (or an
amplifier or other equipment with a MPEG decoder).
PCM: Select when connected to a 2-channel digital
stereo amplifier. The DVD+VCR outputs sounds in the
PCM 2ch format when you play a DVD video disc
recorded on the MPEG1, or MPEG2 recording system.
Move
Auto Play
Select
DVD
You can set up the DVD+VCR so a DVD disc automatically starts playing whenever the DVD is inserted.
If Auto Play mode is set to “On”, the DVD player will find
the title with the longest playback time and play it back
automatically.
On: Auto Play function is activated.
Off: Auto Play function is not activated.
ote
The Auto Play function may not work for some DVDs.
Sample Freq. (Frequency)
To change the Sample Frequency setting, first select
the desired Dolby Digital, DTS, and MPEG mode as
indicated as above.
If your receiver or amplifier is NOT capable of handling
96 kHz signals, select 48 kHz. When this choice is
made, this unit will automatically convert any 96 kHz
signals to 48 kHz, so your system can decode them.
If your receiver or amplifier is capable of handling
96 kHz signals, select 96 kHz. When this choice is
made, this unit will pass through each type of signal
without any further processing.
19
PREPARATION
Dolby Digital
The DVD format provides program soundtracks as
accurately as possible, thanks to digital audio technology. However, you may wish to compress the dynamic
range of the audio output (the difference between the
loudest sounds and the quietest ones). This allows you
to listen to a movie at a lower volume without losing
clarity of sound. Set DRC to On for this effect.
Before Operation - DVD Part (Continued)
LOCK
Password
DVD
Setting your password
LOCK
Rating
Unlock
Password
New
Country Code
US
Move
Rating
If you change the rating level to “7” or lower, you must
enter a 4-digit “password” to prevent playback of discs
with higher ratings.
Select
DVD
Movies on DVDs may contain scenes not suitable for
children. Therefore, discs may contain Parental Control
information that applies to the complete disc or to
certain scenes on the disc. These scenes are rated
from 1 to 8, and alternatively, more suitable scenes are
available for selection on some discs. Ratings are different in each country. The Parental Control feature allows
you to prevent discs from being played by your children
or to have certain discs played with alternative scenes.
1
2
3
4
5
Select “Rating” on the Setup menu.
While “Rating” is selected, press B.
When you have not entered a password:
Enter a 4-digit password using the number buttons to
create a personal 4-digit security password, then
press SELECT/ENTER ( ). Enter the 4-digit password again and press SELECT/ENTER ( ) to verify.
When you have already registered a password:
Enter the 4-digit password using the number buttons to confirm the personal 4-digit security password, then press SELECT/ENTER ( ). If you make
a mistake before pressing SELECT/ENTER ( ),
press CLEAR and enter the 4-digit security password again.
Select a rating from 1 to 8 using the v/V buttons. One (1) has the least playback restrictions.
Eight (8) has the most playback restrictions.
Unlock: If you select Unlock, Parental Control is
not active. The disc will play in full.
Ratings 1 to 8: Some discs contain scenes not
suitable for children. If you set a rating for the player, all disc scenes with the same rating or lower will
be played. Higher rated scenes will not be played
unless an alternative scene is available on the disc.
The alternative must have the same rating or the
lower one. If no suitable alternative is found, playback will stop. You must enter the 4-digit password
or change the rating level in order to play the disc.
Press SELECT/ENTER ( ) to confirm your rating selection, then press SETUP to exit the
menu.
20
1
2
3
4
Select “Password” on the Setup menu.
While “Password” is selected, press B.
While “New” is selected, press SELECT/ENTER
( ).
Enter a 4-digit password using the numbered
buttons to create a personal 4-digit security
password then press SELECT/ENTER ( ).
ip
If you make a mistake before pressing SELECT/ENTER
( ), press CLEAR to delete the entered all-digit or
press b to delete one by one and correct it.
5
Enter the 4-digit password again and press
SELECT/ENTER ( ) to verify.
Changing the 4-digit password
1 Follow Steps 1-2 as shown above (Setting your
password).
2 Enter the old password, then press SELECT/ENTER
( ).
3 Select “Change” using v/V buttons then press
SELECT/ENTER ( ).
4 Enter the new 4-digit password, then press
SELECT/ENTER ( ).
5 Enter the 4-digit password again and press
SELECT/ENTER ( ) to verify.
If you forget your 4-digit password
If you forget your password, to clear the current password, follow the procedure below.
1 Press SETUP to display the setup menu.
2 Use the Number buttons to enter the 6-digit number
“210499”.
3 Enter a new code as shown above (Setting your
password).
Country Code
DVD
Enter the code of a country/area which standards were
used to rate the DVD video disc, referring to the list
(See “Country Code List”, page 36.).
Select “Country Code” on the Setup menu.
1
2
3
4
5
6
While “Country Code” is selected, press B.
Follow step 3 of “Rating” on left.
Select the first character using the v/V buttons.
Shift the cursor using B button and select the
second character using v/V buttons.
Press SELECT/ENTER ( ) to confirm your country
code selection, then press SETUP to exit the menu.
Operation with tape
Normal Playback
Search
Preparation:
This function lets you search for a desired tape section
in either direction: forward or reverse quickly and visually.
1
2
Insert a prerecorded video cassette.
The
indicator will light and the DVD+VCR will
power-up automatically.
Make sure that the
indicator in the display
window is not lighted. If it is, press POWER once.
If a tape without a safety tab is inserted, the unit will
start playback automatically.
H) once.
Press PLAY (H
PLAY appears on the TV screen .
It is not necessary to select the tape speed for playback. It will be automatically selected by the DVD+VCR.
During playback, the TV/VCR selector switches to VCR
mode automatically.
x) to stop playback.
Press STOP (x
3 STOP
appears on the TV screen.
If the tape reaches the end before STOP (x) is
pressed, the DVD+VCR will automatically stop, rewind,
eject, and will turn itself off (Only when no disc).
Tracking Control
Auto Tracking
The automatic tracking function adjusts the picture to
remove snow or streaks.
The AUTO TRACKING function works in the following
cases:
A tape is played back for the first time.
Tape speed (SP, LP, SLP) changes.
Streaks or snow appear because of scratches on the tape.
Manual Tracking
If noise appears on the screen during playback, press
v/V
V) on the remote control or
either CH/TRK (v
v/V
V) on the front panel until the noise on
CHANNEL (v
the screen is reduced.
In case of vertical tremble, adjust these controls very carefully.
Tracking is automatically reset to normal when the tape is
ejected or the power cord is unplugged for more than 3 seconds.
Special Effect Playbacks
ote on special effects playbacks.
Horizontal lines (noise bars) will appear on the TV screen. This
is normal.
The audio is automatically muted during special effect modes,
so there is no sound during search.
During the high-speed picture search modes, a short period is
needed to stabilize tape speed when re-entering the PLAY
mode. Slight interference may be observed during this period.
1 Press BACKWARD (.) or FORWARD (>)
during playback.
The DVD+VCR will be activated in the SEARCH
mode.
If the DVD+VCR is left in the SEARCH mode for more
than 3 minutes, the DVD+VCR will automatically enter the
PLAY mode, to protect the tape and video heads.
2 To return to playback, press PLAY (H).
Still Picture and Frame-by-Frame Playback
1 Press PAUSE/STEP (X) during playback.
Still picture will appear on the TV screen.
If a still picture vibrates vertically, stabilize it by pressing
CH/TRK (v/V) on the remote control.
If the DVD+VCR is left in the STILL mode for more than 5
minutes, the DVD+VCR will automatically enter the STOP
mode to protect the tape and video heads.
2 Press PAUSE/STEP (X) repeatedly to advance the
video picture one frame at a time while viewing a still
picture.
3 To return to playback, press PLAY (H).
Slow Motion
1 During the still mode, press FORWARD (>).
The tape will be played back at a speed 1/19 times
slower than the normal speed.
During slow playback, use CH/TRK (v/V) on the Remote
Control to minimize noise bands.
If slow motion mode continues for more than 3 minutes,
the DVD+VCR will automatically change to playback
mode.
2 To return to playback, press PLAY (H).
Ad JUMP (Advertisement Jump)
This is useful for skipping commercials or short program
segments.
1 Press Ad JUMP during the playback mode.
The tape will be fast forward picture search through
30 seconds of recording.
The skipping time can be extended by pressing Ad JUMP.
Subsequent presses result in advancing the fast forward
picture search time by 30-second increments (maximum 3
minutes).
2 When the search is completed, the DVD+VCR will go
into playback mode automatically.
ote
This unit can play back videotape recorded in stereo,
but the playback sound turns to be monaural.
21
OPERATION
Turn on the TV.
Tune the TV to the DVD+VCR output channel (CH 3 or 4) or
set the TV’s source selector to VIDEO.
If a direct VIDEO/AUDIO connection is made between the
DVD+VCR and the TV, set the TV’s source selector to VIDEO.
Set the Output Source to VCR as shown in “Setting the
Output Source” on page 6.
Operation with tape (Continued)
Normal Recording
Timer Recording
Preparation:
This DVD+VCR can be programmed to record up to 8
programs within a period of 1 year. For unattended
recording, the timer needs to know the channels to be
recorded and the starting and ending times.
Turn on the power of both the DVD+VCR and TV.
Tune the TV to the DVD+VCR output channel (CH 3 or 4) or
set the TV’s source selector to VIDEO.
If a direct VIDEO/AUDIO connection is made between the
DVD+VCR and the TV, set the TV’s source selector to
VIDEO.
1 Insert a video cassette that the safety tab intact.
the desired channel by using CH/TRK
2 Select
v/V
V).
(v
3
If you are recording from another source via audio/video
input jacks (at the Rear or Front panel), select the
LINE1 or LINE2 by pressing INPUT.
Set the desired recording speed (SP or SLP) by
pressing SP/SLP.
This DVD+VCR is not designed to record in LP mode.
Things to know before starting
If you try to set the program timer before setting the clock,
PLEASE SET THE CLOCK appears for a moment and
then CLOCK menu appears on the TV screen. Set the time
and date before proceeding.
Make sure a tape is in the DVD+VCR and the safety tab is
in place or the tape will be automatically ejected.
Preparation:
Turn on the power of both the DVD+VCR and the TV.
Be sure the TV is set to the DVD+VCR output channel (3 or 4).
Make sure the TUNING BAND in the TUNING menu is set
appropriately (TV or CATV).
z) once.
REC (z
4 Press
Recording will start. (The REC indicator will light in
1 Press MENU and the MAIN menu will appear.
the display window.)
2 Use v/VV to choose the PROGRAM menu.
Press SELECT/ENTER ( ) to go to the
3
PROGRAM menu.
x) to stop recording.
Press STOP (x
The PROGRAM menu will appear.
5
x
REC indicator appears only when the Output Source is
set to VCR.
If a cassette with no safety tab is loaded, the cassette
will be ejected automatically.
If the tape reaches the end before STOP ( ) is pressed,
the DVD+VCR will automatically stop, rewind, eject, and it
will turn itself off (Only when no disc).
If all programs have already been entered, FULLY
PROGRAMMED message will appear for a moment
and then PROGRAM 1 will appear on the TV screen.
To pause the recording
1 Press PAUSE/STEP (X) to pause the tape during
recording.
The REC indicator will flash in the display window.
2 When you want to continue recording, press
z).
PAUSE/STEP (X) or press REC (z
After 5 minutes in pause mode, the tape will be stopped
automatically to protect the tape and the video heads.
To record one TV program while
watching another
1 Press TV/VCR to select the TV mode during recording.
The TV indicator appears.
2 Using the TV, select the channel to be viewed.
ips
Always use PAUSE/STEP (X) for the best results when making changes during recording.
For example: To change channels during recording, first press
PAUSE/STEP (X) to put the unit in pause mode. Then select
the desired channel on the DVD+VCR, and press
PAUSE/STEP (X) again to resume recording.
22
4 Use b/BB to choose the PROGRAM No. (1-8).
V to choose the MONTH option.
5 Use
B to choose the desired month.
Use b/B
V to choose the DAY option.
6 Use
B to choose the desired day.
Use b/B
Use V to choose the START option.
7 Use b/BB to choose the desired start time.
V to choose the STOP option.
8 Use
B to choose the desired stop time.
Use b/B
V to choose the CHANNEL option.
9 Use
B to choose the desired channel
Use b/B
(Channel, LINE1 or LINE2).
Cable Users: If you have CABLE TV and used Cable Box
in Connecting Antenna/Cable TV to DVD+VCR (page 11),
using a cable box converter, you must set the channel in
this step to match the cable box output channel (usually
CH 3 or 4). Change channels on the cable box instead of
channels on the DVD+VCR.
Operation with tape (Continued)
10
11
Use V to choose the SPEED option.
B to choose the desired recording
Use b/B
speed (AUTO, SP or SLP).
AUTO mode determines how long tape is left and
switches speed from SP to SLP, if necessary, to
complete recording the program. There will be some
picture and sound distortion at the point of the speed
change.
Checking (Erasing) the Timer Program
Programming can be checked whenever the DVD+VCR
is turned on.
1 Press MENU and the MAIN menu will appear.
2 Use v/V to choose the PROGRAM menu.
Press SELECT/ENTER ( ) and the PROGRAM
menu will appear.
Use V to choose the REPEAT option.
B to choose the desired repeat (ONCE,
Use b/B
WEEKLY or DAILY).
ONCE event....for recording up to 8 programs on a
single day or over the days within a period of 1 year.
WEEKLY event....for recording up to 8 programs on a
certain day of every week.
DAILY event....for recording up to 8 programs at the
same time(s) from Monday through Friday.
3 Use b/B to select a program you want to check or
erase. If you want to erase the program, press
CLEAR.
4 Press MENU to return to the TV screen.
ip
If the input data is wrong, use v to select the data
B.
and correct it using b/B
12
Press MENU, the program will be memorized
at the DVD+VCR.
indicator lights in the display window.
If the program preset time is past, the PAST TIME
PROGRAMMED message will appear on the TV
screen. Return to the incorrect program and program
it with the correct time.
If you had entered a past date, the timer recording
will be performed on that date of the next year.
Additional programs may be entered by repeating
steps 1-12.
If the starting and ending
times of two or more timer
recordings overlap on the
same day, priority is given to
the earliest recording. For
example, in the diagram at
left Program number 2 will
not be recorded until Program number 1 is finished. The
first part of Program number 2 will not be recorded.
Likewise, Program number 3 will not be recorded until
Program number 2 is finished, and so on.
Cable Users: If your cable hookup is via a TV converter box, you can program multiple recordings only on
the converter box output channel. This is because the
converter determines what channel you view through
your DVD+VCR.
ip
If you have finished programming and you want to set the
DVD+VCR to record the programs you have entered.
MAKE SURE YOU HAVE INSERTED A TAPE INTO THE
DVD+VCR. The DVD+VCR is now set to record the preset
programs.
ote
If the power fails or the DVD+VCR is unplugged from the AC
outlet, the correct clock time and timer settings are kept in
memory for approximately 3 seconds. After 3 seconds, the
clock and program timer will be reset when power is restored.
Reset the clock according to instructions.
After setting up a timer recording, recording will start if no other
timer recordings are scheduled to occur at the same time (see
“Program Priority” at right).
23
OPERATION
Program Priority
Operation with tape (Continued)
Instant Timer Recording
Dubbing and Editing
Instant Timer Recording allows you to make a recording
easily of a preset length without using the program
timer.
If you wish to edit or dub your camcorder (or another
VCR) recordings to this DVD+VCR, the rear (or Front)
panel mounted Audio and Video (A/V) input jacks
make the connections quick and easy. These direct
A/V jacks will also provide better picture results than
using the RF jack on the rear panel.
Preparation:
Turn on the power of both the DVD+VCR and the TV.
Be sure the TV is tuned to the DVD+VCR output channel (3 or 4).
If a direct VIDEO/AUDIO connection is made between the
DVD+VCR and the TV, set the TV’s source selector to VIDEO.
1 Insert a video cassette with the safety tab intact.
the desired channel by using CH/TRK
2 Select
v/V
V) or number (0-9).
(v
The channel number appears on the TV screen.
3
If you are recording from another source via audio/video
input jacks (at the Rear or Front panel), select the
LINE1 or LINE2.
Set the desired recording speed (SP or SLP) by
pressing SP/SLP.
The tape speed will appear on the TV screen.
4 Press REC (zz) twice.
the camcorder’s (or another VCR’s) A/V
1 Connect
outputs to your DVD+VCR as illustrated on page 13.
the input channel “LINE2”. (Press INPUT to
2 Set
select LINE2.)
If you have connected your DVD+VCR to the A/V input
jacks on the rear of DVD+VCR, you should select the
input channel LINE1 by pressing INPUT twice.
the tape in the camcorder (or another
3 Play
VCR). If you have a TV attached to your
DVD+VCR, you can see the video playing.
you desire recording to begin, press
4 When
z) once to start.
DVD+VCR’s REC (z
You can stop the recording by pressing STOP (x).
Refer to page 13 for the connection.
ote
The menu as illustrated, will appear on the TV screen.
5
Recording will start. (The
indicator will light.)
z) repeatedly to select the recordPress REC (z
ing time length.
At the end of the recording, the DVD+VCR will stop
recording and shut off.
During Instant Timer Recording, changing the channel
on the DVD+VCR will not be possible.
You can stop the recording by pressing STOP (x).
INSTANT TIMER RECORD MENU
INSTANT TIMER RECORD
0H30M ..... 9H00M ➝ 0H00M
CHANNEL
SPEED
2
SP
START
LENGTH
NOW
0H30M
Length Display
(each additional press of
z) increases recording
REC (z
time 30 minutes)
Checking the Recording Time
Press REC (z) once to check the recording time. The
recalled setting will automatically return to the TV
screen after 6 seconds.
To extend the Recording Time
The recording time can be extended anytime by pressing REC (z).
Subsequent presses result in advancing the recording
time by 30-minute increments.
otes
If you press PAUSE/STEP (X) during instant timer recording, the DVD+VCR will enter the recording pause mode.
Instant timer recording is cancelled.
If the DVD+VCR is set to “0H00M”, the DVD+VCR goes to
normal recording mode.
24
Before recording, please confirm the recording start position.
Copying from DVD to VCR
This unit allows you to copy the contents of a DVD to a
VHS tape.
ote
If the DVD you are attempting to copy is copy protected,
you will not be able to copy the disc. It is not permitted
to copy Macrovision encoded DVDs. “Lock” is
displayed in the display window.
1
2
3
Insert Disc
Insert the disc you wish to copy in the DVD deck
and close the disc tray.
Insert VHS Tape
Insert a blank VHS video tape into the VCR deck.
H) on the DVD deck.
Press PLAY (H
The DVD will go into play mode
If the DVD disc menu appears, you may need to press
the PLAY (H) manually to begin copying.
z) on the VCR deck or on the
REC (z
4 Press
remote control.
5 Stop the Copy Process.
The DVD+VCR will go into Record mode.
When the DVD is finished playing, press STOP (x) to end
the copy.
You must stop the Copy process manually when the DVD
movie ends, otherwise the unit may record over and over
again.
ote
When you stop the DVD playback during copying, the recording on VCR is stopped automatically.
Operation with tape (Continued)
Real-Time Counter
Shows length of tape run in hours, minutes, and seconds. Press CLK/CNT to select the real-time counter
display.
Every press of CLK/CNT changes the TV screen as
illustrated below.
2:15 AM
CLOCK
0:05:25
COUNTER
REM 1:07
REMAINING TIME
Counter changes to “0:00:00” when the cassette is
ejected.
The real-time counter does not operate if nothing is recorded on the tape.
The real-time counter will not work unless a tape is
inserted.
Additional Information
In manual recording, Timer recording, Instant Timer
Recording, playback, or fast forward modes, the DVD+VCR
automatically starts rewinding the tape at the end of the
tape. The cassette will stop at the beginning of the tape and
be ejected, and the DVD+VCR will turn itself off (Only when
no disc).
After you have finished using the DVD+VCR, rewind, eject,
and remove the cassette. Place the cassette in its protective sleeve to protect it from dust. It is not necessary to
rewind the cassette before removing it, but if you do, it will
be ready to play or record the next time you use it.
Be sure the DVD+VCR Channel Selector is on the correct
channel you wish to record. The channel that is being
recorded can always be checked by setting the television
on the DVD+VCR channel (3 or 4) and pressing the
TV/VCR selector to turn off the DVD+VCR’s TV indicator.
Do not attempt to hook up more than one television set to
the DVD+VCR for either recording or playback.
Counter Memory Function
Auto Play System
This is useful if there is a section of tape you want to
view immediately after recording or if you want to return
to the same point several times.
This DVD+VCR features automatic playback.
Load a cassette (with the safety tab removed).
1
CLK/CNT repeatedly to display the real2 Press
time counter appears on the TV screen.
the point that you want locate later, reset the
3 Atreal-time
counter to “0:00:00” by pressing
CLEAR.
Begin recording or playing a tape.
4 Continue to play or record.
x) when recording or playback finPress STOP (x
5 ishes.
.).
BACKWARD (.
6 Press
The tape automatically stops when the tape counter
returns to about “0:00:00”.
The Output Source is changed to VCR mode automatically.
The power turns on automatically and playback begins.
At the end of the tape, the DVD+VCR stops, then rewinds.
The cassette is ejected after rewinding and turn itself off
automatically.
ote
Auto power off does not function during regular DVD play
mode. (DVD+VCR power stays on.)
Tape Remaining
This function allows the time of the remaining tape to be
displayed during recording or playback.
Press CLK/CNT until the REM indicator displays on the
TV screen during recording or playback.
ote
The remaining tape length indicator may not be displayed
correctly depending on the condition of the tape and the kind of
the tape (T-140, T-160, or T-210 etc.).
25
OPERATION
Tape Counter Memory Feature
Operation with DVD
Playing DVD
Playback Setup
Moving to another TITLE
DVD
Turn on the TV and select the video input source connected to the DVD+VCR.
Audio system: Turn on the audio system and select
the input source connected to the DVD+VCR.
Set the Output Source to DVD as shown in “Setting
the Output Source” on page 6.
1
your chosen disc in the tray, with the
2 Load
playback side down.
Z) to close the tray.
Press OPEN/CLOSE (Z
3 Playback
starts automatically. If playback does not
Z) to open the disc tray.
Press OPEN/CLOSE (Z
start, press PLAY (H).
In some cases, the disc menu might appear
instead.
If a menu screen is displayed
The menu screen may be displayed first after loading a
DVD which offers a menu.
DVD
Use the b/B/v/V buttons to select the title/chapter you
want to view, then press SELECT/ENTER ( ) to start
playback. Press TITLE or DISC MENU to return to the
menu screen.
4
To stop playback at any other time,
x).
press STOP (x
This is RESUME STOP mode.
x)
To exit RESUME STOP mode, press STOP (x
again.
otes
If Parental Control is set and the disc is not within the
Rating settings (not authorized), the 4-digit password
must be entered and/or the disc must be authorized
(see “LOCK”, on page 20).
DVDs may have a region code.
Your DVD+VCR will not play discs that have a region
code different from your DVD+VCR. The region code
for this DVD+VCR is 1 (one).
Do not keep an image or on-screen displayed for a
long time.
DVD
1/3
When a disc has more than one title, you can move to
another title as follows:
Press DISPLAY then press v/V to select the title
icon. Then press the appropriate numbered button
(0-9) to select a title number.
To go directly to any title at STOP mode
(or RESUME STOP mode), press the number button
(0-9).
Moving to another CHAPTER
DVD
1 / 12
When a title on a disc has more than one chapter, you
can move to another chapter as follows:
Press BACKWARD (.) or FORWARD (>) briefly
during playback to return to the beginning of the
current chapter or to select the next chapter.
Press BACKWARD (.) twice briefly to step back to
the previous chapter.
To go directly to any chapter during playback,
V to select chapter
press DISPLAY. Then, press v/V
icon. Then, enter the chapter number using the
numbered buttons (0-9).
Slow Motion
DVD
1 Press PAUSE/STEP (X) during playback.
The DVD+VCR will now go into PAUSE mode.
2 Press BACKWARD (.) or FORWARD (>)
during pause mode.
The DVD+VCR will enter SLOW mode.
3 Use BACKWARD (.) or FORWARD (>) to
select the required speed: t 1/16, t 1/8, t 1/4 or
t 1/2 (backward), or T 1/16, T 1/8, T 1/4 or T
1/2 (forward).
4 To return to playback, press PLAY (H).
Still Picture and Frame-by-Frame
Playback DVD
1 Press PAUSE/STEP (X) during playback.
The DVD+VCR will now go into PAUSE mode.
2 You can advance the picture frame by frame by
pressing PAUSE/STEP (X) repeatedly on the remote
control.
3 To return to playback, press PLAY (H).
Search
DVD
1 Press and hold BACKWARD (.) or FORWARD (>)
for about two seconds during playback.
The DVD+VCR will now go into SEARCH mode.
General Features
ote
Unless stated otherwise, all operations described use
the remote control. Some features may also be
available on the Setup menu.
26
2 Press and hold BACKWARD (.) or FORWARD (>)
repeatedly to select the required speed: mX2, mX4,
mX16, mX100 (backward) or MX2, MX4,
MX16, MX100 (forward).
3 To return to playback, press PLAY (H).
Operation with DVD (Continued)
General Features (Continued)
Zoom
Repeat
The Zoom function allows you to enlarge the video
image and to move through the enlarged image.
DVD
Title
DVD Video Discs - Repeat Chapter/Title/Off
1 To repeat the currently playing chapter, press
REPEAT.
The Repeat Chapter icon appears on the TV screen.
2 To repeat the title currently playing, press REPEAT a
second time.
The Repeat Title icon appears on the TV screen.
3 To exit Repeat mode, press REPEAT a third time.
The Repeat Off icon appears on the TV screen.
Repeat A-B
DVD
A-B
To repeat a sequence:
1 Press A-B at your chosen starting point.
DVD
1 Press ZOOM during playback or still playback to activate the Zoom function.
The square frame will be displayed in the right bottom of the
picture. If no button is pressed for more than 10 seconds,
the square frame will disappear.
Each press of the ZOOM button changes the TV screen in
the sequence shown below.
400% size → 1600% size → multi zoom mode → normal size
2 Use the b / B / v / V buttons to move through the
zoomed picture (400% or 1600%), or to enlarge and
reduce the picture size through the multi zoom mode.
3 To resume normal playback, press ZOOM repeatedly
until the normal picture appears.
“A-” appears briefly on the TV screen.
“A-B” appears briefly on the TV screen, and the repeat
sequence begins.
3 To cancel the sequence, press A-B.
3D Surround
DVD
3D SUR
This unit can produce a 3D Surround effect, which
simulates multi-channel audio playback from two
conventional stereo speakers, instead of the five or
more speakers normally required to listen to multichannel audio from a home theater system.
1 Press DISPLAY during playback.
2 Use v/V to select the sound icon.
The sound option will be highlighted.
3 Use b/B to to select “3D SUR”.
To turn off the 3D Surround effect, select “Normal”.
Time Search
DVD
-:--:--
The Time Search function allows you to start playing at
any chosen time on the disc.
1 Press DISPLAY during playback. The on-screen display appears on the screen.
The Time Search box shows the elapsed playing time of the
current disc.
V to select the Time
2 Within 10 seconds, use v/V
Search icon in the on-screen display.
The “-:--:--” appears in the Time Search box.
3 Within 10 seconds, use the numbered buttons to
enter the required start time. Enter hours, minutes
and seconds from left to right in the box.
If you enter the wrong numbers, press CLEAR to remove the
numbers you entered. Then enter the correct numbers.
4 Within 10 seconds, press SELECT/ENTER ( ).
Playback starts from the selected time on the disc. If you enter
an invalid time, playback will continue from the current point.
ote
The zoom function may not work for some DVDs.
The zoom function may not work on multi-angle
scenes.
Marker Search
DVD
#1
1/9
1 2 3 4 5 6 7 8 9
You can start playback from a memorized point. Up to
nine points can be memorized.
To enter a mark, follow these steps.
1 During disc playback, press MARKER when playback
reaches the spot that you want to memorize.
The Marker icon will appear on the TV screen briefly.
2 Repeat step 1 to enter up to nine Marker points on a
disc.
To Recall a Marked Scene
1 During disc playback, press SEARCH.
The Marker Search menu will appear on the screen.
2 Within 10 seconds, press 1/2 to select a Marker number that you want to recall.
3 Press SELECT/ENTER ( ).
Playback will start from the Marked scene.
4 To remove the MARKER SEARCH menu, press
SEARCH.
To clear a Marked Scene
1 During disc playback, press SEARCH.
The Marker Search menu will appear on the screen.
2 Within 10 seconds, press 1/2 to select a Marker number that you want to erase.
3 Press CLEAR.
The Marker number will be erased from the list.
4 Repeat steps 2 and 3 to erase additional Marker
numbers.
5 To remove the MARKER SEARCH menu, press
SEARCH.
Screen Saver
The screen saver picture appears when you leave the
DVD+VCR in stop mode for about five minutes.
27
OPERATION
2 Press A-B again at your chosen end point (after more
than 3 seconds).
Operation with DVD (Continued)
Special DVD Features
Checking the contents of DVD Video
discs: Menus
DVDs may contain menus that allow you to access special features. To use the disc menu, press DISC MENU.
Then, press the appropriate number button to select an
option. Or, use b/B/v/V buttons to highlight your selection, then press SELECT/ENTER ( ).
Title Menu
DVD
1 Press TITLE.
If the current title has a menu, the menu will appear on the
screen. Otherwise, the disc menu may appear.
2 The menu can list camera angles, spoken language
and subtitle options, and chapters for the title.
3 To remove the title menu, press TITLE.
Disc Menu
DVD
1 Press DISC MENU.
The disc menu is displayed.
2 To remove the disc menu, press DISC MENU again.
Camera Angle
DVD
1/1
If the disc contains scenes recorded at different camera
angles, you can change to a different camera angle
during playback.
Press ANGLE repeatedly during playback to select a
desired angle.
The number of the current angle appears on the TV screen.
Changing the Audio Language
DVD
1 ENG
D
3/2.1 CH
Press AUDIO repeatedly during playback to hear a
different audio language or audio track.
Subtitle
DVD
ABC
1 ENG
Press SUBTITLE repeatedly during playback to see the
different subtitle languages.
If
ote
appears, the feature is not available on the disc.
28
Operation with Audio CD and MP3 Discs
Playing an Audio CD and MP3
Notes on MP3 Recordings
Discs
About MP3
MP3
An MP3 file is audio data compressed by using the
MPEG1 audio layer-3 file-coding scheme. We call
files that have the “.mp3” file extension “MP3 files”.
The player cannot read an MP3 file that has a file
extension other than “.mp3”.
Some discs may be incompatible due to different
recording formats or the condition of the disc.
The DVD+VCR can play an audio CD. Also, the
DVD+VCR can play MP3 formatted recordings on
CD-ROM, CD-R or CD-RW discs.
Before playing MP3 recordings, read the notes on MP3
Recordings on the right side of this page.
1
Insert a disc and close the tray.
Audio CD; Audio CD menu appears on the TV
screen. Go to step 3.
MP3 disc; The MP3 menu appears on the TV
screen. Go to step 2
00:52:44
00:00:00
1 / 12
Audio CD
1 / 104
MP3
Program
List
MP3 Disc compatibility with this player is limited as follows:
1.
2.
3.
4.
Program
List
TRACK 1
Add
Music Folder 1
Add
TRACK 2
Add All
Music Folder 2
Add All
TRACK 3
Delete
Music Folder 3
Delete
TRACK 4
Delete All
Music Folder 4
Delete All
TRACK 5
Music Folder 5
TRACK 6
Music Folder 6
TRACK 7
Music Folder 7
TRACK 8
Music Folder 8
5.
Audio CD Menu
MP3 Menu
v/V to select a folder then press
2 Press
SELECT/ENTER ( ).
6.
v/V to select a track then press
3 Press
PLAY (H) or SELECT/ENTER ( ).
7.
8.
A list of files in the folder appears.
Playback starts.
During playback, the current track’s elapsed playing
time will appear on the display window and menu.
Playback will stop at the end of the disc.
ips
Press and hold V to move to the next page.
Press and hold v to move to the previous page.
If you are in a file list on the MP3 menu and want to
return to the Folder list, use the v/V to highlight
and press SELECT/ENTER ( ).
playback at any other time,
4 TopressstopSTOP
x).
(x
Sampling Frequency / only at 8 - 48 kHz.
Bit rate / within 32 - 320kbps.
CD-R physical format should be “ISO 9660”.
If you record MP3 files using the software which
cannot create a FILE SYSTEM, for example “DirectCD” etc., it is impossible to playback MP3 files. We
recommend that you use “Easy-CD Creator”, which
creates an ISO9660 file system.
A single session disc requires MP3 files in the first
track. If there is no MP3 file in the 1st track, it cannot play back MP3 files. If you wish to playback MP3
files, format all the data in the disc or use a new
one.
File names should be named using 8 letters or less
and must incorporate “.mp3” extension
e.g. “********.MP3”.
Do not use special letters such as “/ : * ? “ < > ” etc.
Total number of files and folders on the disc should
be less than 999.
This DVD+VCR requires discs/recordings to meet
certain technical standards in order to achieve optimal
playback quality. Pre-recorded DVDs are automatically
set to these standards. There are many different types
of recordable disc formats (including CD-R containing
MP3 files). That requires certain pre-existing conditions
(see above) to insure compatible playback.
Customers should also note that permission must
be required in order to download MP3 files and
music from the Internet. Our company has no right
to grant such permission. Permission should
always be sought from the copyright owner.
29
OPERATION
CD
Operation with Audio CD and MP3 Discs (Continued)
Pause
CD
Random
MP3
CD
MP3
Press BACKWARD (.) or FORWARD (>) briefly
during playback to go to the next track or to return to
the beginning of the current track.
Press BACKWARD (.) twice briefly to step back to
the previous track.
To go directly to any track, enter the track number
using the numbered buttons (0-9) during playback.
Repeat Track/All/Off
CD
MP3
1 To repeat the track currently playing, press REPEAT.
The Repeat icon and “TRACK” appears on the menu screen.
2 To repeat all tracks on a disc, press REPEAT a second time.
The Repeat icon and “ALL” appears on the menu screen.
3 To cancel Repeat mode, press REPEAT a third time.
Search
CD
MP3
1 Press and hold BACKWARD (.) or FORWARD
(>) for about two seconds during playback.
The player will now go into SEARCH mode.
2 Press and hold BACKWARD (.) or FORWARD
(>) repeatedly to select the required speed: mX2,
mX4, mX8 (backward) or MX2, MX4, MX8
(forward).
Search speed and direction are indicated on the menu
screen.
3 To exit SEARCH mode, press PLAY(H).
ote
The DVD+VCR mutes sound during search mode of
MP3 files.
30
MP3
1 Press RANDOM during playback or when playback is
stopped.
The unit automatically begins Random Playback and
“Random” appears on the menu screen.
1 Press PAUSE/STEP (X) during playback.
2 To return to playback, press PLAY or press
PAUSE/STEP (X) again.
Moving to another Track
CD
2 To return to normal playback, press RANDOM repeatedly until “Random” disappears on the menu screen.
Repeat A-B
CD
To repeat a sequence:
1 Press A-B at your chosen starting point.
Repeat icon and “A” appears on the menu screen.
2 Press A-B again at your chosen end point.
The Repeat icon and “A - B” appears on the menu screen,
and the repeat sequence begins.
3 To exit the sequence and return to normal play, press
A-B again.
CD
MP3
Programmed Playback with
Audio CD and MP3 Discs
Repeat Programmed Tracks
To repeat the track currently playing, press REPEAT.
The Repeat icon and “TRACK” appears on the screen.
The Program function enables you to store your favorite
tracks from any disc in the player memory.
Program can contain 99 tracks (Audio CD) or 300
tracks (MP3).
1 Insert an Audio CD or MP3 disc.
2 Press v / V / b / B to select a track on the List.
PROGRAM. Or, press v / V / b / B to high3 Press
light the “Add” icon then press SELECT/ENTER
Audio CD or MP3 menu will appear.
( ).
The selected track is added to the program list.
steps 2-3 to place additional tracks on
4 Repeat
the Program list.
5 Press v / V / b / B to move to the Program list.
v/V to select the track you want to start
6 Press
playing.
00:52:44
00:00:00
1 / 12
To repeat all tracks on the program list, press
REPEAT a second time.
The Repeat icon and “ALL” appears on the screen.
To cancel Repeat mode, press REPEAT a third time.
Erasing a Track from Program List
1 Select the track that you wish to erase from the
Program list.
2 Press v / V / b / B to highlight the “Delete” icon then
press SELECT/ENTER ( ). Or, press CLEAR.
The selected track is deleted on the program list.
3 Repeat steps 1-2 to delete additional tracks on the
Program list.
Erasing the Complete Program List
Press v / V / b / B to highlight the “Delete All” icon then
press SELECT/ENTER ( ).
All tracks on the program list are deleted.
OPERATION
Programmed Playback
1 / 104
MP3
Audio CD
Program
List
Program
List
TRACK 1
Add
TRACK 8
Add
2-Music2
TRACK 2
Add All
TRACK 3
1-Music1.mp3
Add All
7-Music7
TRACK 3
Delete
TRACK 12
2-Music2.mp3
Delete
4-Music4
TRACK 4
Delete All
Delete All
1-Music1
TRACK 7
3-Music3.mp3
TRACK 5
TRACK 6
4-Music4.mp3
3-Music3
TRACK 6
TRACK 9
5-Music5.mp3
6-Music6
TRACK 7
TRACK 1
6-Music6.mp3
11-Music11
TRACK 8
TRACK 10
7-Music7.mp3
15-Music15
ips
Press and hold V to move to the next page.
Press and hold v to move to the previous page.
If you are in a file list on the MP3 menu and want to
return to the Folder list, use the v/V to highlight
and
press SELECT/ENTER ( ).
7
H) or SELECT/ENTER ( ) to start.
Press PLAY (H
Playback begins in the order in which you programmed
the tracks.
Playback stops after all of the tracks on the Program list
have played once.
resume normal playback from programmed
8 Toplayback,
select a track on the List then press
SELECT/ENTER ( ).
31
Troubleshooting
Check the following guide for the possible cause of a problem before contacting service.
Symptom
Cause
Correction
No power.
The power cord is disconnected.
Plug the power cord into the wall outlet
securely.
The power is on, but
the DVD+VCR does not
work.
No disc is inserted.
No tape is inserted.
Insert a disc or tape. (Check that the
disc or tape indicator in the display
window is lit.)
No picture.
The TV is not set to receive DVD+VCR
signal output.
Select the appropriate video input mode
on the TV so the picture from the
DVD+VCR appears on the TV screen.
TV/VCR mode for DVD+VCR is set to
TV.
Press the TV/VCR button on the remote
control repeatedly to choose VCR
mode. TV indicator disappears in the
display window.
The video cable is not connected
securely.
Connect the video cable securely.
The connected TV power is turned off.
Turn on the TV.
The equipment connected with the
audio cable is not set to receive
DVD+VCR signal output.
Select the correct input mode of the
audio receiver so you can listen to the
sound from the DVD+VCR.
The audio cables are not connected
securely.
Connect the audio cable securely.
The power of the equipment connected
with the audio cable is turned off.
Turn on the equipment connected with
the audio cable.
The Digital Audio Output is set to the
wrong position.
Set the Digital Audio Output to the
correct position, then turn on the
DVD+VCR again by pressing POWER.
The disc is dirty.
Clean the disc.
Tape heads are dirty.
Clean video heads.
Tape is a rental or was recorded on
another VCR.
Use CH/TRK (v/V) for manual tracking
adjustment while tape is playing.
No disc is inserted.
No tape is inserted.
Insert a disc or tape. (Check that the
disc or tape indicator in the display
window is lit.)
An unplayable disc is inserted.
Insert a playable disc. (Check the disc
type, color system, and Regional code.)
The disc is placed upside down.
Place the disc with the playback side down.
The disc is not placed within the guide.
Place the disc on the disc tray correctly
inside the guide.
The disc is dirty.
Clean the disc.
The Rating level is set.
Cancel the Rating function or change
the rating level.
The remote control is not pointed at the
remote sensor of the DVD+VCR.
Point the remote control at the remote
sensor of the DVD+VCR.
The remote control is too far from the
DVD+VCR.
Operate the remote control within 23 ft
(7 m).
There is an obstacle in the path of the
remote control and the DVD+VCR.
Remove the obstacle.
The batteries in the remote control are
exhausted.
Replace the batteries with new ones.
This remote control use the same
buttons for VCR and DVD functions
(ex. PLAY).
When using a VCR, first press the VCR
button. When using a DVD, first press
the DVD button.
No sound.
The playback picture is
poor.
The DVD+VCR does
not start playback.
The remote control
does not work properly.
32
Troubleshooting (Continued)
Correction
Some channels are
skipped over when
using CH/TRK (v/V)
Those channels were deleted with the
CH. ADD/DEL option.
Use CH. ADD/DEL. to restore channels.
See “Channel Selection” on page 15.
Picture and sound of
broadcasting channel
are weak or missing.
Antenna or cables are loose.
Tighten connections or replace cable.
Wrong TUNING BAND option is being
used.
Try all TUNING BAND options. See
“Channel Selection” on page 15 for
details.
Camcorder image is not
shown.
Camcorder is off.
Turn camcorder on and operate
properly.
Camcorder image via
A/V input to DVD+VCR
is not shown on TV
screen.
DVD+VCR SOURCE SELECT is not set
to LINE1 or LINE2.
Press INPUT to select LINE input channel (LINE1 or LINE2).
Timer recording is not
possible.
Clock in DVD+VCR is not set to correct
time.
Set clock to correct time. See “Setting
the Clock” on page 16.
Timer has been programmed
incorrectly.
Reprogram Timer. See “Timer
Recording” on pages 22 and 23.
indicator does not appear after programming timer.
Reprogram Timer.
indicator appears
after DVD+VCR is turned
off.
DVD+VCR is in Timer Recording mode.
This is the normal indication that the
DVD+VCR is in TIMER mode.
The “PROGRESSIVE
SCAN MODE” message
remains to be
displayed.
DVD+VCR was turned off while setting
the Progressive scan mode.
Keep pressing the STOP button for
more than 5 seconds.
The HiFi-videotape
cannot be played back
in stereo.
This unit can play back videotape
recorded in stereo, but the playback
sound turns to be monaural.
_____________
Moisture Condensation
Moisture condensation can occur:
In locations where moisture condensation may occur:
• When the DVD+VCR is moved from a cold place to a
warm place.
• Keep the DVD+VCR plugged into an AC power outlet
with POWER On. This will help prevent condensation.
• Under extremely humid conditions.
• When condensation has occurred, wait a few hours
for the DVD+VCR to dry before using it.
33
REFERENCE
Cause
Symptom
Troubleshooting (Continued)
Video Head Cleaning
Video head clogging
The video heads are the means by which the unit reads the picture from the tape during playback. In the unlikely
event that the heads become dirty enough to be clogged, no picture will be played back. This can easily be determined if, during playback of a known good tape, there is good sound, but no picture (picture is extremely snowy). If
this is the case, use a high quality head cleaning system or have them cleaned professionally.
Snowy Picture
Video head cleaning
Video head cleaning is needed when the playback picture becomes unclear. This signifies that the heads are getting
dirty and can occur when playing poor quality or damaged tapes. If the heads require cleaning, use an equivalent
high quality chemical non-abrasive (wet) head cleaning tape or have them cleaned professionally. If playing a head
cleaning tape in the unit once does not improve the picture, play it several times before requesting service.
otes
DO NOT ATTEMPT TO CLEAN THE VIDEO HEADS OR SERVICE THE UNIT BY REMOVING THE TOP COVER.
Video heads may eventually wear out and should be replaced when they fail to produce clear pictures.
To help prevent video head clogging, use only good quality VHS tapes. Discard worn out tapes.
34
Language Code List
Language
Code
Language
Code
Language
Code
Language
Code
Abkhazian
6566
Fiji
7074
Lingala
7678
Singhalese
8373
Afar
6565
Finnish
7073
Lithuanian
7684
Slovak
8375
Afrikaans
6570
French
7082
Macedonian
7775
Slovenian
8376
Albanian
8381
Frisian
7089
Malagasy
7771
Somali
8379
Amharic
6577
Galician
7176
Malay
7783
Spanish
6983
Arabic
6582
Georgian
7565
Malayalam
7776
Sudanese
8385
Armenian
7289
German
6869
Maltese
7784
Swahili
8387
Assamese
6583
Greek
6976
Maori
7773
Swedish
8386
Aymara
6588
Greenlandic
7576
Marathi
7782
Tagalog
8476
Azerbaijani
6590
Guarani
7178
Moldavian
7779
Tajik
8471
Bashkir
6665
Gujarati
7185
Mongolian
7778
Tamil
8465
Basque
6985
Hausa
7265
Nauru
7865
Tatar
8484
Bengali; Bangla
6678
Hebrew
7387
Nepali
7869
Telugu
8469
Bhutani
6890
Hindi
7273
Norwegian
7879
Thai
8472
Bihari
6672
Hungarian
7285
Oriya
7982
Tibetan
6679
Breton
6682
Icelandic
7383
Panjabi
8065
Tigrinya
8473
Bulgarian
6671
Indonesian
7378
Pashto, Pushto
8083
Tonga
8479
Burmese
7789
Interlingua
7365
Persian
7065
Turkish
8482
Byelorussian
6669
Irish
7165
Polish
8076
Turkmen
8475
Cambodian
7577
Italian
7384
Portuguese
8084
Twi
8487
Catalan
6765
Japanese
7465
Quechua
8185
Ukrainian
8575
Chinese
9072
Javanese
7487
Rhaeto-Romance 8277
Urdu
8582
Corsican
6779
Kannada
7578
Romanian
8279
Uzbek
8590
Croatian
7282
Kashmiri
7583
Russian
8285
Vietnamese
8673
Czech
6783
Kazakh
7575
Samoan
8377
Volapük
8679
Danish
6865
Kirghiz
7589
Sanskrit
8365
Welsh
6789
Dutch
7876
Korean
7579
Scots Gaelic
7168
Wolof
8779
English
6978
Kurdish
7585
Serbian
8382
Xhosa
8872
Esperanto
6979
Laothian
7679
Serbo-Croatian
8372
Yiddish
7473
Estonian
6984
Latin
7665
Shona
8378
Yoruba
8979
Faeroese
7079
Latvian, Lettish
7686
Sindhi
8368
Zulu
9085
35
REFERENCE
Enter the appropriate code number for the initial settings “Disc Audio”, “Disc Subtitle” and/or “Disc Menu”
(See page 18).
Country Code List
Enter the appropriate code number for the initial setting “Country Code” (See page 20).
Country
Afghanistan
Albania
Algeria
American Samoa
Andorra
Angola
Anguilla
Antarctica
Antigua and Barbuda
Argentina
Armenia
Aruba
Australia
Austria
Azerbaidjan
Bahamas
Bahrain
Bangladesh
Barbados
Belarus
Belgium
Belize
Benin
Bermuda
Bhutan
Bolivia
Bosnia-Herzegovina
Botswana
Bouvet Island
Brazil
British Indian
Ocean Territory
Brunei Darussalam
Bulgaria
Burkina Faso
Burundi
Cambodia
Cameroon
Canada
Cape Verde
Cayman Islands
Central African Republic
Chad
Chile
China
Christmas Island
Cocos (Keeling) Islands
Colombia
Comoros
Congo
Cook Islands
Costa Rica
Croatia
Cuba
Cyprus
Czech Republic
Denmark
Djibouti
Dominica
Dominican Republic
East Timor
Ecuador
Egypt
36
Code
AF
AL
DZ
AS
AD
AO
AI
AQ
AG
AR
AM
AW
AU
AT
AZ
BS
BH
BD
BB
BY
BE
BZ
BJ
BM
BT
BO
BA
BW
BV
BR
IO
BN
BG
BF
BI
KH
CM
CA
CV
KY
CF
TD
CL
CN
CX
CC
CO
KM
CG
CK
CR
HR
CU
CY
CZ
DK
DJ
DM
DO
TP
EC
EG
Country
Code
El Salvador
SV
Equatorial Guinea
GQ
Eritrea
ER
Estonia
EE
Ethiopia
ET
Falkland Islands
FK
Faroe Islands
FO
Fiji
FJ
Finland
FI
Former Czechoslovakia
CS
Former USSR
SU
France
FR
France (European Territory) FX
French Guyana
GF
French Southern Territories TF
Gabon
GA
Gambia
GM
Georgia
GE
Germany
DE
Ghana
GH
Gibraltar
GI
Great Britain
GB
Greece
GR
Greenland
GL
Grenada
GD
Guadeloupe (French)
GP
Guam (USA)
GU
Guatemala
GT
Guinea
GN
Guinea Bissau
GW
Guyana
GY
Haiti
HT
Heard and
McDonald Islands HM
Honduras
HN
Hong Kong
HK
Hungary
HU
Iceland
IS
India
IN
Indonesia
ID
Iran
IR
Iraq
IQ
Ireland
IE
Israel
IL
Italy
IT
Ivory Coast
CI
Jamaica
JM
Japan
JP
Jordan
JO
Kazakhstan
KZ
Kenya
KE
Kiribati
KI
Kuwait
KW
Kyrgyzstan
KG
Laos
LA
Latvia
LV
Lebanon
LB
Lesotho
LS
Liberia
LR
Libya
LY
Liechtenstein
LI
Lithuania
LT
Luxembourg
LU
Country
Macau
Macedonia
Madagascar
Malawi
Malaysia
Maldives
Mali
Malta
Marshall Islands
Martinique (French)
Mauritania
Mauritius
Mayotte
Mexico
Micronesia
Moldavia
Monaco
Mongolia
Montserrat
Morocco
Mozambique
Myanmar
Namibia
Nauru
Nepal
Netherlands
Netherlands Antilles
New Caledonia (French)
New Zealand
Nicaragua
Niger
Nigeria
Niue
Norfolk Island
North Korea
Northern Mariana Islands
Norway
Oman
Pakistan
Palau
Panama
Papua New Guinea
Paraguay
Peru
Philippines
Pitcairn Island
Poland
Polynesia (French)
Portugal
Puerto Rico
Qatar
Reunion (French)
Romania
Russian Federation
Rwanda
S. Georgia
& S. Sandwich Isls.
Saint Helena
Saint Kitts
& Nevis Anguilla
Saint Lucia
Saint Pierre and Miquelon
Saint Tome and Principe
Code
MO
MK
MG
MW
MY
MV
ML
MT
MH
MQ
MR
MU
YT
MX
FM
MD
MC
MN
MS
MA
MZ
MM
NA
NR
NP
NL
AN
NC
NZ
NI
NE
NG
NU
NF
KP
MP
NO
OM
PK
PW
PA
PG
PY
PE
PH
PN
PL
PF
PT
PR
QA
RE
RO
RU
RW
GS
SH
KN
LC
PM
ST
Country
Saint Vincent
& Grenadines
SamoaWS
San Marino
Saudi Arabia
Senegal
Seychelles
Sierra Leone
Singapore
Slovak Republic
Slovenia
Solomon Islands
Somalia
South Africa
South Korea
Spain
Sri Lanka
Sudan
Suriname
Svalbard and
Jan Mayen Islands
Swaziland
Sweden
Switzerland
Syria
Tadjikistan
Taiwan
Tanzania
Thailand
Togo
Tokelau
Tonga
Trinidad and Tobago
Tunisia
Turkey
Turkmenistan
Turks and Caicos Islands
Tuvalu
Uganda
Ukraine
United Arab Emirates
United Kingdom
United States
Uruguay
USA Minor Outlying Islands
Uzbekistan
Vanuatu
Vatican City State
Venezuela
Vietnam
Virgin Islands (British)
Virgin Islands (USA)
Wallis and Futuna Islands
Western Sahara
Yemen
Yugoslavia
Zaire
Zambia
Zimbabwe
Code
VC
SM
SA
SN
SC
SL
SG
SK
SI
SB
SO
ZA
KR
ES
LK
SD
SR
SJ
SZ
SE
CH
SY
TJ
TW
TZ
TH
TG
TK
TO
TT
TN
TR
TM
TC
TV
UG
UA
AE
UK
US
UY
UM
UZ
VU
VA
VE
VN
VG
VI
WF
EH
YE
YU
ZR
ZM
ZW
Specifications
General
Power requirements
Power consumption
Dimensions (approx.)
Mass (approx.)
Operating temperature
Operating humidity
Signal system
AC 120V , 60 Hz
21W
16.9" X 3.1" X 10.8" (430 X 78.5 X 273 mm) (w x h x d)
8.82 lbs (4.0 kg)
41°F to 104°F (5 °C to 40°C)
5 % to 90 %
NTSC
Inputs
ANTENNA IN
VHS VIDEO IN
VHS AUDIO IN
75 ohms (VHF/UHF/CATV)
1 Vp-p 75 ohms, sync negative, RCA jack x 2
-6.0 dBm more than 47 kohms, RCA jack x 2
VIDEO OUT
S-VIDEO OUT
1 Vp-p 75 ohms, sync negative
(Y) 1.0 V (p-p), 75 ohms, negative sync, Mini DIN 4-pin x 1
(C) 0.286 V (p-p) 75 ohms
(Y) 1.0 V (p-p), 75 ohms, negative sync, RCA jack x 1
(Pb)/(Pr) 0.7 V (p-p), 75 ohms, RCA jack x 2
0.5 V (p-p), 75 ohms, RCA jack x 1
2.0 Vrms (1 KHz, 0 dB), 600 ohms, RCA jack (L, R) x 1
Channel 3 or 4 (Swichable)
Outputs
COMPONENT VIDEO OUT
(PROGRESSIVE SCAN)
Audio output (digital audio)
Audio output (analog audio)
RF OUT
VCR Specifications
Head system
Timer
Tape speed
Tape width
Maximum recording time
Rewind time
Channel coverage
Frequency range
Signal-to-noise ratio
Four head helical scan azimuth system
12-hour display type with AM, PM
SP: 33.35 mm/sec, LP: 16.67 mm/sec, SLP: 11.12 mm/sec
12.7 mm
SP: 2 HOURS (T-120), SLP: 6 HOURS (T-120)/8 HOURS (T-160)
About 3 minutes (T-120)
VHF: 2-13, UHF: 14-69, CATV: 1-125 (4A, A-W, W+1 - W+84, A-5 - A-1)
200Hz to 10kHz
More than 43dB
Laser system
Frequency response
Signal-to-noise ratio
Harmonic distortion
Dynamic range
REFERENCE
DVD Specifications
Semiconductor laser, wavelength 650 nm
DVD (PCM 96 kHz): 8 Hz to 44 kHz, DVD (PCM 48 kHz): 8 Hz to 22 kHz
CD: 8 Hz to 20 kHz
More than 100dB (ANALOG OUT jacks only)
Less than 0.008%
More than 95 dB (CD), More than 100 dB (DVD)
Accessory:
Video cable x 1, Audio cable (L/R) x 1, RF 75-ohm Coaxial Cable x 1, Remote control x 1, Batteries x 2
Design and specifications are subject to change without notice.
37
For assistance in obtaining repairs and operational information, please contact the following Toll Free Number:
DIAL TOLL FREE: 1-800-813-3435
Weekdays 7:30AM ~ 4:00PM Central Time
Also, you may write to SANYO Manufacturing Corporation, 3333 Sanyo Road Forrest City Arkansas 72335
LIMITED WARRANTY
LABOR 90 DAYS
PARTS 1 YEAR
CARRY-IN ONLY
THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED FROM A WAL-MART STORE AND USED IN THE UNITED
STATES OF AMERICA, EXCLUDING HAWAII AND ALL U.S. TERRITORIES AND PROTECTORATES. THIS WARRANTY APPLIES ONLY TO
THE ORIGINAL RETAIL PURCHASER AND DOES NOT APPLY TO PRODUCTS USED FOR ANY INDUSTRIAL, PROFESSIONAL OR
COMMERCIAL PURPOSE.
Subject to the OBLIGATIONS and EXCLUSIONS below, SANYO Manufacturing Corporation (“SANYO”) warrants this SANYO product
against defects in materials and workmanship for the periods of LABOR and PARTS specified above. SANYO will repair or replace (at its
option) the product and any of its parts which fail to conform to this warranty with new or refurbished products or parts. The warranty period
commences on the date the product was first purchased at retail from a Wal-Mart Store.
OBLIGATIONS
In order to obtain warranty service, the product must be delivered to and picked up from a Wal-Mart Store at the original retail purchaser’s
expense. The original dated bill of sale, or sales slip from a Wal-Mart Store must be submitted to a Wal-Mart Store at the time warranty service
is requested.
EXCLUSIONS
1. This warranty does not cover (A) the adjustment of customer-operated controls as explained in the appropriate model’s instruction manual,
or (B) the repair of any product whose serial number has been altered, defaced or removed.
2. This warranty shall not apply to the cabinet or cosmetic parts, broken or damaged video heads, batteries or routine maintenance.
3. This warranty does not apply to uncrating, setup, installation, removal of the product for repair or reinstallation of the product after repair.
4. This warranty does not apply to repairs or replacements necessitated by any cause beyond the control of SANYO including, but not limited
to, any malfunction, defect or failure caused by or resulting from unauthorized service or parts, improper maintenance, operation contrary to
furnished instructions, shipping or transit accidents, modification or repair by user or any third party, abuse, misuse, neglect, accident,
incorrect line voltage, fire, flood or other Acts of God, or normal wear and tear.
The foregoing is in lieu of all other express warranties and SANYO does not assume or authorize any party to assume for it any other
obligation or liability.
THE DURATION OF ANY WARRANTIES WHICH MAY BE IMPLIED BY LAW (INCLUDING THE WARRANTIES OF MERCHANTABILITY AND
FITNESS) IS LIMITED TO THE TERM OF THIS WARRANTY. IN NO EVENT SHALL SANYO OR THE MANUFACTURER OF THE PRODUCT
BE LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM OWNERSHIP OR USE OF THIS PRODUCT,
OR FOR ANY DELAY IN THE PERFORMANCE OF ITS OBLIGATIONS UNDER THIS WARRANTY DUE TO CAUSES BEYOND ITS
CONTROL.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS AND/OR DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO
YOU.
THIS WARRANTY GIVES YOU SPECIAL LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE.
For your protection in the event of theft or loss of this product, please keep the following information with a sales receipt in a safe place.
Model No.
Serial No.
Date of Purchase
Purchase Price
Where Purchased
SANYO Manufacturing Corporation
SANYO Electric Co., Ltd.
Printed in China.
Copyright SANYO, 2004 All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement