National Instruments SCXI-1520 User manual

Add to my manuals
163 Pages

advertisement

National Instruments SCXI-1520 User manual | Manualzz
SCXI
TM
SCXI-1520 User Manual
SCXI-1520 User Manual
May 2009
372583E-01
Support
Worldwide Technical Support and Product Information
ni.com
National Instruments Corporate Headquarters
11500 North Mopac Expressway Austin, Texas 78759-3504 USA Tel: 512 683 0100
Worldwide Offices
Australia 1800 300 800, Austria 43 662 457990-0, Belgium 32 (0) 2 757 0020, Brazil 55 11 3262 3599,
Canada 800 433 3488, China 86 21 5050 9800, Czech Republic 420 224 235 774, Denmark 45 45 76 26 00,
Finland 358 (0) 9 725 72511, France 01 57 66 24 24, Germany 49 89 7413130, India 91 80 41190000,
Israel 972 3 6393737, Italy 39 02 41309277, Japan 0120-527196, Korea 82 02 3451 3400,
Lebanon 961 (0) 1 33 28 28, Malaysia 1800 887710, Mexico 01 800 010 0793, Netherlands 31 (0) 348 433 466,
New Zealand 0800 553 322, Norway 47 (0) 66 90 76 60, Poland 48 22 328 90 10, Portugal 351 210 311 210,
Russia 7 495 783 6851, Singapore 1800 226 5886, Slovenia 386 3 425 42 00, South Africa 27 0 11 805 8197,
Spain 34 91 640 0085, Sweden 46 (0) 8 587 895 00, Switzerland 41 56 2005151, Taiwan 886 02 2377 2222,
Thailand 662 278 6777, Turkey 90 212 279 3031, United Kingdom 44 (0) 1635 523545
For further support information, refer to the Technical Support Information Document. To comment on National
Instruments documentation, refer to the National Instruments Web site at ni.com/info and enter the info code
feedback.
© 2001–2009 National Instruments Corporation. All rights reserved.
Important Information
Warranty
The SCXI-1520 is warranted against defects in materials and workmanship for a period of one year from the date of shipment, as evidenced
by receipts or other documentation. National Instruments will, at its option, repair or replace equipment that proves to be defective during the
warranty period. This warranty includes parts and labor.
The media on which you receive National Instruments software are warranted not to fail to execute programming instructions, due to defects in
materials and workmanship, for a period of 90 days from date of shipment, as evidenced by receipts or other documentation. National Instruments
will, at its option, repair or replace software media that do not execute programming instructions if National Instruments receives notice of such defects
during the warranty period. National Instruments does not warrant that the operation of the software shall be uninterrupted or error free.
A Return Material Authorization (RMA) number must be obtained from the factory and clearly marked on the outside of the package before any
equipment will be accepted for warranty work. National Instruments will pay the shipping costs of returning to the owner parts which are covered by
warranty.
National Instruments believes that the information in this document is accurate. The document has been carefully reviewed for technical accuracy. In
the event that technical or typographical errors exist, National Instruments reserves the right to make changes to subsequent editions of this document
without prior notice to holders of this edition. The reader should consult National Instruments if errors are suspected. In no event shall National
Instruments be liable for any damages arising out of or related to this document or the information contained in it.
EXCEPT AS SPECIFIED HEREIN, NATIONAL INSTRUMENTS MAKES NO WARRANTIES, EXPRESS OR IMPLIED, AND SPECIFICALLY DISCLAIMS ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. CUSTOMER’S RIGHT TO RECOVER DAMAGES CAUSED BY FAULT OR NEGLIGENCE ON THE PART OF NATIONAL
INSTRUMENTS SHALL BE LIMITED TO THE AMOUNT THERETOFORE PAID BY THE CUSTOMER. NATIONAL INSTRUMENTS WILL NOT BE LIABLE FOR DAMAGES RESULTING FROM
LOSS OF DATA, PROFITS, USE OF PRODUCTS, OR INCIDENTAL OR CONSEQUENTIAL DAMAGES, EVEN IF ADVISED OF THE POSSIBILITY THEREOF. This limitation of the
liability of National Instruments will apply regardless of the form of action, whether in contract or tort, including negligence. Any action against
National Instruments must be brought within one year after the cause of action accrues. National Instruments shall not be liable for any delay in
performance due to causes beyond its reasonable control. The warranty provided herein does not cover damages, defects, malfunctions, or service
failures caused by owner’s failure to follow the National Instruments installation, operation, or maintenance instructions; owner’s modification of the
product; owner’s abuse, misuse, or negligent acts; and power failure or surges, fire, flood, accident, actions of third parties, or other events outside
reasonable control.
Copyright
Under the copyright laws, this publication may not be reproduced or transmitted in any form, electronic or mechanical, including photocopying,
recording, storing in an information retrieval system, or translating, in whole or in part, without the prior written consent of National
Instruments Corporation.
National Instruments respects the intellectual property of others, and we ask our users to do the same. NI software is protected by copyright and other
intellectual property laws. Where NI software may be used to reproduce software or other materials belonging to others, you may use NI software only
to reproduce materials that you may reproduce in accordance with the terms of any applicable license or other legal restriction.
Trademarks
National Instruments, NI, ni.com, and LabVIEW are trademarks of National Instruments Corporation. Refer to the Terms of Use section
on ni.com/legal for more information about National Instruments trademarks.
Other product and company names mentioned herein are trademarks or trade names of their respective companies.
Members of the National Instruments Alliance Partner Program are business entities independent from National Instruments and have no agency,
partnership, or joint-venture relationship with National Instruments.
Patents
For patents covering National Instruments products/technology, refer to the appropriate location: Help»Patents in your software,
the patents.txt file on your media, or the National Instruments Patent Notice at ni.com/patents.
WARNING REGARDING USE OF NATIONAL INSTRUMENTS PRODUCTS
(1) NATIONAL INSTRUMENTS PRODUCTS ARE NOT DESIGNED WITH COMPONENTS AND TESTING FOR A LEVEL OF
RELIABILITY SUITABLE FOR USE IN OR IN CONNECTION WITH SURGICAL IMPLANTS OR AS CRITICAL COMPONENTS IN
ANY LIFE SUPPORT SYSTEMS WHOSE FAILURE TO PERFORM CAN REASONABLY BE EXPECTED TO CAUSE SIGNIFICANT
INJURY TO A HUMAN.
(2) IN ANY APPLICATION, INCLUDING THE ABOVE, RELIABILITY OF OPERATION OF THE SOFTWARE PRODUCTS CAN BE
IMPAIRED BY ADVERSE FACTORS, INCLUDING BUT NOT LIMITED TO FLUCTUATIONS IN ELECTRICAL POWER SUPPLY,
COMPUTER HARDWARE MALFUNCTIONS, COMPUTER OPERATING SYSTEM SOFTWARE FITNESS, FITNESS OF COMPILERS
AND DEVELOPMENT SOFTWARE USED TO DEVELOP AN APPLICATION, INSTALLATION ERRORS, SOFTWARE AND HARDWARE
COMPATIBILITY PROBLEMS, MALFUNCTIONS OR FAILURES OF ELECTRONIC MONITORING OR CONTROL DEVICES,
TRANSIENT FAILURES OF ELECTRONIC SYSTEMS (HARDWARE AND/OR SOFTWARE), UNANTICIPATED USES OR MISUSES, OR
ERRORS ON THE PART OF THE USER OR APPLICATIONS DESIGNER (ADVERSE FACTORS SUCH AS THESE ARE HEREAFTER
COLLECTIVELY TERMED “SYSTEM FAILURES”). ANY APPLICATION WHERE A SYSTEM FAILURE WOULD CREATE A RISK OF
HARM TO PROPERTY OR PERSONS (INCLUDING THE RISK OF BODILY INJURY AND DEATH) SHOULD NOT BE RELIANT SOLELY
UPON ONE FORM OF ELECTRONIC SYSTEM DUE TO THE RISK OF SYSTEM FAILURE. TO AVOID DAMAGE, INJURY, OR DEATH,
THE USER OR APPLICATION DESIGNER MUST TAKE REASONABLY PRUDENT STEPS TO PROTECT AGAINST SYSTEM FAILURES,
INCLUDING BUT NOT LIMITED TO BACK-UP OR SHUT DOWN MECHANISMS. BECAUSE EACH END-USER SYSTEM IS
CUSTOMIZED AND DIFFERS FROM NATIONAL INSTRUMENTS' TESTING PLATFORMS AND BECAUSE A USER OR APPLICATION
DESIGNER MAY USE NATIONAL INSTRUMENTS PRODUCTS IN COMBINATION WITH OTHER PRODUCTS IN A MANNER NOT
EVALUATED OR CONTEMPLATED BY NATIONAL INSTRUMENTS, THE USER OR APPLICATION DESIGNER IS ULTIMATELY
RESPONSIBLE FOR VERIFYING AND VALIDATING THE SUITABILITY OF NATIONAL INSTRUMENTS PRODUCTS WHENEVER
NATIONAL INSTRUMENTS PRODUCTS ARE INCORPORATED IN A SYSTEM OR APPLICATION, INCLUDING, WITHOUT
LIMITATION, THE APPROPRIATE DESIGN, PROCESS AND SAFETY LEVEL OF SUCH SYSTEM OR APPLICATION.
Conventions
The following conventions are used in this manual:
<>
Angle brackets that contain numbers separated by an ellipsis represent a
range of values associated with a bit or signal name—for example,
AO <3..0>.
»
The » symbol leads you through nested menu items and dialog box options
to a final action. The sequence File»Page Setup»Options directs you to
pull down the File menu, select the Page Setup item, and select Options
from the last dialog box.
This icon denotes a note, which alerts you to important information.
This icon denotes a caution, which advises you of precautions to take to
avoid injury, data loss, or a system crash. When this symbol is marked on a
product, refer to the Read Me First: Safety and Radio-Frequency
Interference for information about precautions to take.
bold
Bold text denotes items that you must select or click in the software, such
as menu items and dialog box options. Bold text also denotes parameter
names.
italic
Italic text denotes variables, emphasis, a cross-reference, or an introduction
to a key concept. Italic text also denotes text that is a placeholder for a word
or value that you must supply.
monospace
Text in this font denotes text or characters that you should enter from the
keyboard, sections of code, programming examples, and syntax examples.
This font is also used for the proper names of disk drives, paths, directories,
programs, subprograms, subroutines, device names, functions, operations,
variables, filenames, and extensions.
monospace bold
Bold text in this font denotes the messages and responses that the computer
automatically prints to the screen. This font also emphasizes lines of code
that are different from the other examples.
monospace italic
Italic text in this font denotes text that is a placeholder for a word or value
that you must supply.
Contents
Chapter 1
About the SCXI-1520
What You Need to Get Started ......................................................................................1-1
National Instruments Documentation ............................................................................1-3
Installing Application Software, NI-DAQ, and the E/M Series DAQ Device ..............1-5
Installing the SCXI-1520 Module into the SCXI Chassis...............................1-5
Connecting the SCXI-1520 in an SCXI Chassis to an E/M Series
DAQ Device for Multiplexed Scanning .......................................................1-5
Connecting the SCXI-1520 in a PXI/SCXI Combination Chassis to an
E/M Series DAQ Device for Multiplexed Scanning ....................................1-5
Verifying the SCXI-1520 Installation in Software ........................................................1-6
Installing SCXI Using NI-DAQmx in Software .............................................1-6
Manually Adding Modules in NI-DAQmx .....................................................1-6
Installing SCXI Using Traditional NI-DAQ (Legacy) in Software ................1-6
Manually Adding Modules in Traditional NI-DAQ (Legacy) ........................1-6
Verifying and Self-Testing the Installation .....................................................1-6
Troubleshooting the Self-Test Verification ...................................................................1-7
Troubleshooting in NI-DAQmx ......................................................................1-7
Troubleshooting in Traditional NI-DAQ (Legacy) .........................................1-8
Chapter 2
Connecting Signals
Connecting Bridge Sensor Signals ................................................................................2-1
Quarter-Bridge Type I .....................................................................................2-1
Quarter-Bridge Type II....................................................................................2-2
Half-Bridge Type I ..........................................................................................2-4
Half-Bridge Type II.........................................................................................2-5
Full-Bridge Type I...........................................................................................2-6
Full-Bridge Type II..........................................................................................2-7
Full-Bridge Type III ........................................................................................2-8
Remote Sense ..................................................................................................2-9
Pin Assignments ............................................................................................................2-10
© National Instruments Corporation
v
SCXI-1520 User Manual
Contents
Chapter 3
Configuring and Testing
SCXI-1520 Software-Configurable Settings................................................................. 3-1
Common Software-Configurable Settings ...................................................... 3-1
Bridge Configuration ........................................................................ 3-1
Excitation Level................................................................................ 3-2
Filter Bandwidth ............................................................................... 3-2
Gain/Input Range.............................................................................. 3-3
Null Potentiometers .......................................................................... 3-4
Shunt Calibration Switches .............................................................. 3-4
Modes of Operation .......................................................................... 3-5
Simultaneous Sample and Hold........................................................ 3-5
Configurable Settings in MAX...................................................................................... 3-5
NI-DAQmx ..................................................................................................... 3-6
Creating a Strain Global Channel or Task........................................ 3-7
Creating a Custom Voltage with Excitation Global Channel
or Task ........................................................................................... 3-8
Traditional NI-DAQ (Legacy) ........................................................................ 3-9
Configuring Module Property Pages in Traditional NI-DAQ
(Legacy) ......................................................................................... 3-10
Creating a Strain Virtual Channel .................................................... 3-11
Calibrating a Strain Virtual Channel ................................................ 3-11
Verifying the Signal ...................................................................................................... 3-12
Verifying the Signal in NI-DAQmx Using a Task or Global Channel ........... 3-12
Verifying the Signal in Traditional NI-DAQ (Legacy) .................................. 3-13
Verifying the Signal Using Channel Strings .................................... 3-13
Verifying the Signal Using Strain Virtual Channel.......................... 3-14
Using the Strain Calibration Wizard in NI-DAQmx..................................................... 3-14
Chapter 4
Theory of Operation
Strain-Gauge Theory ..................................................................................................... 4-1
Wheatstone Bridges ........................................................................................ 4-1
Strain Gauges .................................................................................................. 4-2
Acronyms, Formulas, and Variable Definitions ............................................. 4-3
Software Scaling and Equations ..................................................................... 4-4
Quarter-Bridge Type I..................................................................................... 4-4
Quarter-Bridge Type II ................................................................................... 4-6
Half-Bridge Type I.......................................................................................... 4-9
Half-Bridge Type II ........................................................................................ 4-11
Full-Bridge Type I .......................................................................................... 4-13
SCXI-1520 User Manual
vi
ni.com
Contents
Full-Bridge Type II..........................................................................................4-14
Full-Bridge Type III ........................................................................................4-16
SCXI-1520 Theory of Operation ...................................................................................4-18
Bridge Configuration and Completion ............................................................4-21
Excitation.........................................................................................................4-22
Remote Sense ....................................................................................4-23
Gain .................................................................................................................4-24
Filter Bandwidth and Cutoff Frequency..........................................................4-25
Offset Null Compensation...............................................................................4-25
Shunt Calibration.............................................................................................4-27
Simultaneous Sample and Hold.......................................................................4-28
Maximum Simultaneous Sample and Hold Sample Rate Using
NI-DAQmx ....................................................................................4-30
Maximum Simultaneous Sample and Hold Using Traditional
NI-DAQ (Legacy) ..........................................................................4-32
Modes of Operation.........................................................................................4-34
Theory of Multiplexed Mode Operation ...........................................4-34
Theory of Parallel Mode Operation ..................................................4-35
Chapter 5
Using the SCXI-1520
Developing Your Application in NI-DAQmx ...............................................................5-1
Typical Program Flowchart.............................................................................5-2
General Discussion of Typical Flowchart .......................................................5-4
Creating a Task Using DAQ Assistant or Programmatically ...........5-4
Adjusting Timing and Triggering .....................................................5-4
Configuring Channel Properties........................................................5-5
Performing Offset Null Compensation .............................................5-7
Performing Shunt Calibration ...........................................................5-8
Acquiring, Analyzing, and Presenting ..............................................5-8
Completing the Application ..............................................................5-9
Developing an Application Using LabVIEW..................................................5-9
Using a DAQmx Channel Property Node in LabVIEW ...................5-11
Specifying Channel Strings in NI-DAQmx.....................................................5-12
Text Based ADEs..............................................................................5-14
Measurement Studio (Visual Basic, .NET, and C#)........................................5-14
Programmable NI-DAQmx Properties..............................................5-16
Developing Your Application in Traditional NI-DAQ (Legacy) ..................................5-18
Traditional NI-DAQ (Legacy) in LabVIEW...................................................5-19
Typical Program Flow ......................................................................5-20
Configuring the SCXI-1520 Settings Using Traditional NI-DAQ
(Legacy) in LabVIEW ..................................................................................5-22
© National Instruments Corporation
vii
SCXI-1520 User Manual
Contents
Performing Offset Null Compensation Using Traditional NI-DAQ
(Legacy) in LabVIEW.................................................................................. 5-24
Performing Shunt Calibration Using Traditional NI-DAQ (Legacy)
in LabVIEW ................................................................................................. 5-26
Configure, Start Acquisition, and Take Readings Using Traditional
NI-DAQ (Legacy) in LabVIEW .................................................................. 5-27
Converting Scaling Using Traditional NI-DAQ (Legacy) in LabVIEW ........ 5-27
Analyze and Display Using Traditional NI-DAQ (Legacy) in LabVIEW ..... 5-28
Traditional NI-DAQ (Legacy) in Text-Based ADEs ...................................... 5-28
Low-Level DAQ Functions ............................................................................ 5-29
Configuring System Settings Using Traditional NI-DAQ (Legacy) C API ... 5-31
Configuring Module Settings Using Traditional NI-DAQ (Legacy) C API... 5-32
Performing Offset Null Compensation Using Traditional NI-DAQ
(Legacy) C API ............................................................................................ 5-34
Performing Shunt Calibration Using Traditional NI-DAQ
(Legacy) C API ............................................................................................ 5-34
Performing Acquisition Using Traditional NI-DAQ (Legacy) C API............ 5-35
Performing Scaling, Analysis, and Display .................................................... 5-35
Other Application Documentation and Material ........................................................... 5-36
Traditional NI-DAQ (Legacy) CVI Examples................................................ 5-36
Traditional NI-DAQ (Legacy) Measurement Studio Examples ..................... 5-36
Calibrating the Strain System........................................................................................ 5-37
Calibrating the SCXI-1520 ............................................................................. 5-37
Internal Calibration Procedure.......................................................... 5-37
Internal Calibration Using LabVIEW............................................... 5-37
Internal Calibration Using a C-Based ADE ..................................... 5-38
External Calibration.......................................................................... 5-38
Calibrating the System .................................................................................... 5-39
Offset Null Compensation ................................................................ 5-39
Shunt Calibration .............................................................................. 5-39
Appendix A
Specifications
Appendix B
Using SCXI Channel Strings with Traditional NI-DAQ (Legacy) 7.0
or Later
Appendix C
Removing the SCXI-1520
SCXI-1520 User Manual
viii
ni.com
Contents
Appendix D
Common Questions
Glossary
Index
Figures
Figure 2-1.
Figure 2-2.
Figure 2-3.
Figure 2-4.
Figure 2-5.
Figure 2-6.
Figure 2-7.
Figure 2-8.
Quarter-Bridge I Circuit Diagram .........................................................2-2
Quarter-Bridge II Circuit Diagram........................................................2-3
Half-Bridge Type I Circuit Diagram .....................................................2-4
Half-Bridge Type II Circuit Diagram....................................................2-5
Full-Bridge Type I Circuit Diagram......................................................2-6
Full-Bridge Type II Circuit Diagram ....................................................2-7
Full-Bridge Type III Circuit Diagram ...................................................2-8
Remote-Sense Circuit Diagram.............................................................2-9
Figure 4-1.
Figure 4-2.
Figure 4-3.
Figure 4-4.
Figure 4-5.
Figure 4-6.
Figure 4-7.
Figure 4-8.
Basic Wheatstone Bridge Circuit Diagram ...........................................4-1
Quarter-Bridge Type I Measuring Axial and Bending Strain ...............4-4
Quarter-Bridge I Circuit Diagram .........................................................4-5
Quarter-Bridge Type II Measuring Axial and Bending Strain..............4-7
Quarter-Bridge II Circuit Diagram........................................................4-7
Half-Bridge Type I Measuring Axial and Bending Strain ....................4-9
Half-Bridge Type I Circuit Diagram .....................................................4-9
Half-Bridge Type II Rejecting Axial and
Measuring Bending Strain.....................................................................4-11
Half-Bridge Type II Circuit Diagram....................................................4-11
Full-Bridge Type I Rejecting Axial and Measuring Bending Strain.....4-13
Full-Bridge Type I Circuit Diagram......................................................4-13
Full-Bridge Type II Rejecting Axial and Measuring Bending Strain ...4-15
Full-Bridge Type II Circuit Diagram ....................................................4-15
Full-Bridge Type III Measuring Axial and
Rejecting Bending Strain.......................................................................4-17
Full-Bridge Type III Circuit Diagram ...................................................4-17
Block Diagram of SCXI-1314/SCXI-1520 Combination .....................4-19
Signal During Simultaneous Sample-and-Hold Sampling....................4-29
Figure 4-9.
Figure 4-10.
Figure 4-11.
Figure 4-12.
Figure 4-13.
Figure 4-14.
Figure 4-15.
Figure 4-16.
Figure 4-17.
Figure 5-1.
Figure 5-2.
Figure 5-3.
Typical Program Flowchart...................................................................5-3
LabVIEW Channel Property Node with Filtering Enabled
at 10 kHz and SS/H Disabled ................................................................5-12
Typical SCXI-1520 Program Flow with
Traditional NI-DAQ (Legacy)...............................................................5-21
© National Instruments Corporation
ix
SCXI-1520 User Manual
Contents
Figure 5-4.
Figure 5-5.
Using the AI Parameter VI to Set Up the SCXI-1520 .......................... 5-24
Offset Null and Shunt Calibration Flowchart ....................................... 5-30
Figure C-1.
Removing the SCXI-1520..................................................................... C-2
Tables
Table 1-1.
Accessories Available for the SCXI-1520 ............................................ 1-2
Table 2-1.
Table 2-2.
Table 2-3.
Front Signal Pin Assignments .............................................................. 2-11
Rear Signal Pin Assignments................................................................ 2-13
SCXI-1520 Communication Signals..................................................... 2-14
Table 3-1.
Excitation Voltage for Configuration and Gauge Resistances ............. 3-2
Table 4-1.
Table 4-2.
Table 4-3.
Strain-Gauge Configurations ................................................................ 4-2
Control Codes for Coarse and Fine Offset Null Potentiometers........... 4-26
NI-DAQmx Values Used to Determine Maximum Sample Rate
in Multiplexed Mode............................................................................. 4-31
NI-DAQmx Values Used to Determine Maximum Sample Rate
in Parallel Mode .................................................................................... 4-32
Traditional NI-DAQ (Legacy) Values Used to Determine
Maximum Sample Rate in Multiplexed Mode...................................... 4-33
Table 4-4.
Table 4-5.
Table 5-1.
Table 5-2.
Table 5-3.
Table 5-4.
Table 5-5.
Table 5-6.
NI-DAQmx Properties .......................................................................... 5-5
Programming a Task in LabVIEW ....................................................... 5-9
NI-DAQmx Properties .......................................................................... 5-16
Settings for Configuring the SCXI-1520 Through the AI Parameter ... 5-22
Configuration Functions ....................................................................... 5-31
NI-DAQ Functions Used to Configure SCXI-1520.............................. 5-33
Table D-1.
Digital Signals on the SCXI-1520 ....................................................... D-2
SCXI-1520 User Manual
x
ni.com
1
About the SCXI-1520
The SCXI-1520 module is an eight-channel module for interfacing to
strain-gauge bridges and other Wheatstone-bridge based sensors.
Descriptions in this chapter explicitly refer to the first channel (channel 0); however,
the same descriptions are applicable to channels <1..7>.
Note
You can configure all settings on a per channel basis in software.
The SCXI-1520 is configured using Measurement & Automation Explorer
(MAX) or through NI-DAQmx property nodes.
With the SCXI-1520 and the accessory SCXI-1314 terminal block, you can
do the following:
•
Connect sensors of all bridge configurations, including quarter-, half-,
and full-bridge
•
Set the DC voltage excitation between 0 and 10 V (increments
dependent upon the driver software)
•
Programmatically offset null bridge circuits connected to the
SCXI-1520
•
Set the analog input lowpass filter cut-off frequency to 10 Hz, 100 Hz,
1 kHz, 10 kHz, or bypass
•
Set the analog input gain between 1 and 1000 at any one of 49 settings
•
Implement shunt calibration using two independent circuits
•
Connect the bridge for remote-sense voltage excitation
What You Need to Get Started
To set up and use the SCXI-1520, you need the following:
❑ Hardware
© National Instruments Corporation
–
SCXI-1520 module
–
One of the following terminal blocks:
•
SCXI-1314 terminal block
•
SCXI-1314T terminal block
1-1
SCXI-1520 User Manual
Chapter 1
About the SCXI-1520
–
SCXI or PXI/SCXI combo chassis
–
E/M Series DAQ device
–
Computer, if using an SCXI chassis
–
Cabling, cable adapter, and sensors as required for your
application
❑ Software
–
NI-DAQ 7.0 or later
–
Application software, such as LabVIEW, LabWindows™/CVI™,
Measurement Studio, or other programming environments
❑ Documentation
–
Read Me First: Safety and Radio-Frequency Interference
–
DAQ Getting Started Guide
–
SCXI Quick Start Guide
–
SCXI-1520 User Manual
–
Documentation for your hardware
–
Documentation for your software
The optional accessories listed in Table 1-1 are available for the
SCXI-1520.
Table 1-1. Accessories Available for the SCXI-1520
Accessory
Description
SCXI-1314†
Screw terminal block—Mounts on the front of the SCXI-1520 module.
It includes connections and sockets for two shunt calibration resistors and
a quarter-bridge completion resistor per channel.
SCXI-1314T††
RJ-50 terminal block—Mounts on the front of the SCXI-1520 module.
It features eight RJ-50 10-position/10-conductor (10p10c) modular plugs
for connection to hardware TEDS smart sensors.
SCXI-1520 User Manual
1-2
ni.com
Chapter 1
About the SCXI-1520
Table 1-1. Accessories Available for the SCXI-1520 (Continued)
Accessory
Description
SCXI-1310‡
Connector and shell assembly—The SCXI-1310 provides 96 eyelet-type
terminals for easy hook-and-solder signal connection and custom
mass termination connectivity.
TBX-96‡
DIN-rail mounted terminal block with 96 generic screw terminals.
One of the following cables is required to connect the TBX-96 to an
SCXI module:
•
SH96-96 shielded cable, 1 m
•
R96-96 unshielded ribbon cable, 1 m
†
You must wire a shunt resistor between the pins that correspond to the SCA on the SCXI-1314 and the appropriate legs of
the bridge sensor. Refer to Chapter 4, Theory of Operation, for more information.
†† The SCXI-1314T only supports SCA. It does not support SCB. There are no quarter-bridge completion resistors in the
SCXI-1314T. If you are connecting a quarter-bridge sensor to an SCXI-1520 using an SCXI-1314T, you must place an
external resistor between the pins that correspond to PX– and SX+ on the terminals. Refer to Chapter 2, Connecting Signals,
for more information.
‡
There are no quarter-bridge completion resistors in the SCXI-1310 or TBX-96. If you are connecting a quarter-bridge
sensor to an SCXI-1520 using an SCXI-1310 or TBX-96, you must place an external resistor between the pins that
correspond to PX– and SX+ on the terminals. Refer to Chapter 2, Connecting Signals, for more information.
National Instruments Documentation
The SCXI-1520 User Manual is one piece of the documentation set for data
acquisition (DAQ) systems. You could have any of several types of
manuals depending on the hardware and software in the system. Use the
manuals you have as follows:
•
Getting Started with SCXI—This is the first manual you should read.
It gives an overview of the SCXI system and contains the most
commonly needed information for the modules, chassis, and software.
•
SCXI or PXI/SCXI chassis manual—Read this manual for
maintenance information on the chassis and for installation
instructions.
•
The DAQ Getting Started Guide—This document has information on
installing NI-DAQ and the E/M Series DAQ device. Install these
before you install the SCXI module.
•
The SCXI Quick Start Guide—This document contains a quick
overview for setting up an SCXI chassis, installing SCXI modules and
terminal blocks, and attaching sensors. It also describes setting up the
SCXI system in MAX.
© National Instruments Corporation
1-3
SCXI-1520 User Manual
Chapter 1
About the SCXI-1520
•
The SCXI hardware user manuals—Read these manuals for detailed
information about signal connections and module configuration. They
also explain, in greater detail, how the module works and contain
application hints.
•
Accessory installation guides or manuals—Read the terminal block
and cable assembly installation guides. They explain how to physically
connect the relevant pieces of the system. Consult these guides when
you are making the connections.
•
The E/M Series DAQ device documentation—This documentation has
detailed information about the DAQ device that plugs into or is
connected to the computer. Use this documentation for hardware
installation and configuration instructions, specification information
about the DAQ device, and application hints.
•
Software documentation—You may have both application software
and NI-DAQ software documentation. National Instruments (NI)
application software includes LabVIEW, LabWindows/CVI, and
Measurement Studio. After you set up the hardware system, use either
your application software documentation or the NI-DAQ
documentation to help you write your application. If you have a large,
complex system, it is worthwhile to look through the software
documentation before you configure the hardware.
•
One or more of the following help files for software information:
•
–
Start»Programs»National Instruments»NI-DAQ»
NI-DAQmx Help
–
Start»Programs»National Instruments»NI-DAQ»
Traditional NI-DAQ User Manual
–
Start»Programs»National Instruments»NI-DAQ»
Traditional NI-DAQ Function Reference Help
NI strain-gauge application notes or tutorials—NI has additional
material about strain gauges and strain measurements available at
ni.com/support.
You can download NI documents from ni.com/manuals. To download
the latest version of NI-DAQ, click Download Software at ni.com.
SCXI-1520 User Manual
1-4
ni.com
Chapter 1
About the SCXI-1520
Installing Application Software, NI-DAQ, and the
E/M Series DAQ Device
Refer to the DAQ Getting Started Guide packaged with the NI-DAQ
software to install your application software, NI-DAQ driver software, and
the DAQ device to which you will connect the SCXI-1520. NI-DAQ 7.0 or
later is required to configure and program the SCXI-1520 module. If you
do not have NI-DAQ 7.0 or later, you can either contact a NI sales
representative to request it on a CD or download the latest NI-DAQ version
from ni.com.
Note Refer to the Read Me First: Radio-Frequency Interference document before
removing equipment covers or connecting or disconnecting any signal wires.
Installing the SCXI-1520 Module into the SCXI Chassis
Refer to the SCXI Quick Start Guide to install your SCXI-1520 module.
Connecting the SCXI-1520 in an SCXI Chassis to an E/M Series
DAQ Device for Multiplexed Scanning
Refer to the SCXI Quick Start Guide to install the cable adapter and connect
the SCXI modules to the DAQ device.
If you have already installed the appropriate software, refer to Chapter 3,
Configuring and Testing, to configure the SCXI-1520 module(s).
Connecting the SCXI-1520 in a PXI/SCXI Combination Chassis to an
E/M Series DAQ Device for Multiplexed Scanning
Refer to the SCXI Quick Start Guide to connect the SCXI modules to the
DAQ device.
If you have already installed the appropriate software, refer to Chapter 3,
Configuring and Testing, to configure the SCXI-1520 module(s).
© National Instruments Corporation
1-5
SCXI-1520 User Manual
Chapter 1
About the SCXI-1520
Verifying the SCXI-1520 Installation in Software
Refer to the SCXI Quick Start Guide for information on verifying the SCXI
installation.
Installing SCXI Using NI-DAQmx in Software
Refer to the SCXI Quick Start Guide for information on installing modules
using NI-DAQmx in software.
Manually Adding Modules in NI-DAQmx
If you did not auto-detect the SCXI modules, you must manually add each
of the modules. Refer to the SCXI Quick Start Guide to manually add
modules.
NI recommends auto-detecting modules for the first time configuration of the
chassis.
Note
Installing SCXI Using Traditional NI-DAQ (Legacy) in Software
Refer to the SCXI Quick Start Guide for information on installing modules
using Traditional NI-DAQ (Legacy) in software.
Manually Adding Modules in Traditional NI-DAQ (Legacy)
If you did not auto-detect the SCXI modules, you must manually add each
of the modules. Refer to the SCXI Quick Start Guide to manually add
modules.
NI recommends auto-detecting modules for the first time configuration of the
chassis.
Note
Verifying and Self-Testing the Installation
The verification procedure for the SCXI chassis is the same for both
NI-DAQmx and Traditional NI-DAQ (Legacy). To test the successful
installation for the SCXI chassis, refer to the SCXI Quick Start Guide.
Verify that the chassis is powered on and correctly connected to an
E/M Series DAQ device.
SCXI-1520 User Manual
1-6
ni.com
Chapter 1
About the SCXI-1520
After verifying and self-testing the installation, the SCXI system should
operate properly with your ADE software. If the test did not complete
successfully, refer to Chapter 3, Configuring and Testing, for
troubleshooting steps.
Troubleshooting the Self-Test Verification
If the Self-Test Verification did not verify the chassis configuration,
complete the steps in this section to troubleshoot the SCXI configuration.
Troubleshooting in NI-DAQmx
•
•
© National Instruments Corporation
If you get a Verify SCXI Chassis message box showing the SCXI
chassis model number, Chassis ID: x, and one or more messages
stating Slot Number: x Configuration has module: SCXI-XXXX
or 1520, hardware in chassis is: Empty, take the following
troubleshooting actions:
–
Make sure the SCXI chassis is powered on.
–
Make sure all SCXI modules are properly installed in the chassis.
Refer to the SCXI Quick Start Guide for proper installation
instructions.
–
Make sure the cable between the SCXI chassis and E/M Series
DAQ device is properly connected.
–
Inspect the cable connectors for bent pins.
–
Make sure you are using the correct NI cable assembly.
–
Test the DAQ device to verify it is working properly. Refer to the
DAQ device help file for more information.
If you get a Verify SCXI Chassis message box showing the SCXI
chassis model number, Chassis ID: x, and the message Slot
Number: x Configuration has module: SCXI-XXXX or 1520,
hardware in chassis is: SCXI-YYYY, 1520, or Empty,
complete the following troubleshooting steps to correct the error.
1.
Expand the list of NI-DAQmx devices by clicking the + next to
NI-DAQmx Devices.
2.
Right-click the SCXI chassis and click Properties to load the
chassis configurator.
3.
Under the Modules tab, ensure that the cabled module is listed in
the correct slot.
1-7
SCXI-1520 User Manual
Chapter 1
About the SCXI-1520
4.
If the cabled module is not listed in the correct slot, complete the
following troubleshooting steps:
a.
If the cabled module is not listed in the correct slot and the
slot is empty, click the drop-down listbox next to the correct
slot and select the cabled module. Configure the cabled
module following the steps listed in the SCXI Quick Start
Guide. Click OK.
b.
If another module appears where the cabled module should
be, click the drop-down listbox next to the correct slot and
select the cabled module. A message box appears asking you
to confirm the module replacement. Click OK. Configure the
cabled module following the steps listed in the SCXI Quick
Start Guide. Click OK.
•
Ensure that you have the highest priority SCXI module cabled to the
E/M Series DAQ device. Refer to the SCXI Quick Start Guide to find
out which SCXI module in the chassis should be cabled to the DAQ
device.
•
After checking the preceding items, return to the Troubleshooting the
Self-Test Verification section and retest the SCXI chassis.
If these measures do not successfully configure the SCXI system, contact
NI. Refer to the Technical Support Information document for contact
information.
Troubleshooting in Traditional NI-DAQ (Legacy)
SCXI-1520 User Manual
•
If you get the message Unable to test chassis at this time,
you have not designated at least one module as connected to a E Series
DAQ device. Refer to the Traditional NI-DAQ (Legacy) section of
Chapter 3, Configuring and Testing, and change the configuration of
the cabled module in the system from Connected to: None to
Connected to: Device x.
•
If you get the message Failed to find followed by the module
codes and the message Unable to communicate with chassis,
take the following troubleshooting actions:
–
Make sure the SCXI chassis is powered on.
–
Make sure the cable between the SCXI chassis and E Series DAQ
device is properly connected.
–
Inspect the cable connectors for bent pins.
–
Make sure you are using the correct NI cable assembly.
–
Test the DAQ device to verify it is working properly. Refer to the
DAQ device help file for more information.
1-8
ni.com
Chapter 1
About the SCXI-1520
•
If you get the message Failed to find, followed by module codes
and the message Instead found: module with ID 0Xxx, refer
to the Traditional NI-DAQ (Legacy) section of Chapter 3, Configuring
and Testing, and make sure the correct module is in the specified slot.
Delete the incorrect module as described in Appendix C, Removing the
SCXI-1520, and add the correct module as described in the Traditional
NI-DAQ (Legacy) section of Chapter 3, Configuring and Testing.
•
If you get the message Failed to find, followed by a module code
and the message Slot x is empty, make sure the configured module
is installed in the specified slot. If not, install the module by following
the instructions in the Installing the SCXI-1520 Module into the SCXI
Chassis section. If the module is installed in the correct slot, power off
the chassis, remove the module as specified in Appendix C, Removing
the SCXI-1520, and verify that no connector pins are bent on the rear
signal connector. Reinstall the module as described in the Installing the
SCXI-1520 Module into the SCXI Chassis section, ensuring
the module is fully inserted and properly aligned in the slot.
•
After checking the preceding items, return to the Troubleshooting the
Self-Test Verification section and retest the SCXI chassis.
If these measures do not successfully configure the SCXI system, contact
NI. Refer to the Technical Support Information document for contact
information.
© National Instruments Corporation
1-9
SCXI-1520 User Manual
2
Connecting Signals
This chapter describes how to connect Wheatstone bridge sensors to the
SCXI-1520 in quarter-, half-, and full-bridge configurations and for remote
sensing. It also provides the front and rear signal pin assignments of the
module.
Connecting Bridge Sensor Signals
This section discusses how to connect the signals of supported strain-gauge
configuration types as well as full-bridge sensors such as load, force,
torque, and pressure sensors. It also discusses connecting leads for remote
sensing and shunt calibration. Refer to Chapter 4, Theory of Operation, for
a discussion of strain-gauge concepts. Refer to the SCXI-1314 Installation
Guide for more signal connection information.
Notes The circuits in this section illustrate circuits using the SCXI-1314 terminal block.
If you are using the SCXI-1314T terminal block, refer to the SCXI-1314T TEDS Bridge
Sensor Terminal Block Installation Guide for the permitted circuit configuration diagrams.
Refer to Figure 2-5 and use its wiring diagram for full-bridge sensors such as load, force,
torque, and pressure sensors.
Quarter-Bridge Type I
This section provides information for connecting the quarter-bridge
strain-gauge configuration type I. Figure 2-1 shows the quarter-bridge
type I circuit wiring diagram.
Note
S– is left unwired.
© National Instruments Corporation
2-1
SCXI-1520 User Manual
Chapter 2
Connecting Signals
SCXI-1314
Transducer
RL
SCXI-1520 Set Bridge
Configuration to
Quarter Bridge
S+
VCH
R4
(gauge)
+
RL
P+
RL
QTR
+
–
R1
P
+
–
R3
VEX
R2
SCA
You must connect
the shunt calibration
wires externally using
the terminal block
screw connections.
Shunt
Cal A
SCA
RS
Figure 2-1. Quarter-Bridge I Circuit Diagram
The following symbols apply to the circuit diagram and equations:
•
R1 and R2 are half-bridge completion resistors.
•
R3 is the quarter-bridge completion resistor.
•
R4 is the active element measuring tensile strain (+ε).
•
VEX is the excitation voltage.
•
RL is the lead resistance.
•
VCH is the measured voltage.
The value of the quarter-bridge completion resistor, R3, must equal the nominal
resistance of the strain gauge. NI recommends using a 0.1% precision resistor.
Note
Quarter-Bridge Type II
This section provides information for connecting the quarter-bridge
strain-gauge configuration type II. Figure 2-2 shows the quarter-bridge
type II circuit wiring diagram.
SCXI-1520 User Manual
2-2
ni.com
Chapter 2
Connecting Signals
Note The quarter-bridge type II configuration is often confused with the more commonly
used half-bridge type I configuration. In the half-bridge type I configuration, the R3
element is active and bonded to the strain specimen to measure Poisson's ratio, while in the
quarter-bridge type II configuration, the R3 element does not actively measure strain, but
is in close thermal contact with the strain specimen. In quarter-bridge type II configuration,
the R3 element is not bonded to the specimen. Typically it is either physically close to the
specimen or mounted on the same type material at the same temperature, but is not under
strain.
Transducer
SCXI-1314
RL
SCXI-1520 Set Bridge
Configuration to Quarter Bridge
S+
VCH
RL
+
–
P+
R1
R4
(gauge)
+
–
R3
(dummy)
R2
P
RL
VEX
SCA
Shunt
Cal A
RL
SCA
RL
RS
Figure 2-2. Quarter-Bridge II Circuit Diagram
The following symbols apply to the circuit diagram and equations:
Note
•
R1 and R2 are half-bridge completion resistors.
•
R3 is the quarter-bridge temperature-sensing element (dummy gauge).
•
R4 is the active element measuring tensile strain (+ε).
•
VEX is the excitation voltage.
•
RL is the lead resistance.
•
VCH is the measured voltage.
S– and QTR are left unwired.
© National Instruments Corporation
2-3
SCXI-1520 User Manual
Chapter 2
Connecting Signals
Half-Bridge Type I
This section provides information for connecting the half-bridge
strain-gauge configuration type I. Figure 2-3 shows the half-bridge type I
circuit wiring diagram.
Note
S– is left unwired.
SCXI-1314
Transducer
RL
SCXI-1520 Set Bridge
Configuration to Half Bridge
S+
VCH
RL
R4
(gauge)
R3
(gauge)
+
–
P+
R1
+
+
–
v
VEX
R2
P
RL
SCA
Shunt
Cal A
RL
SCA
RL
RS
Figure 2-3. Half-Bridge Type I Circuit Diagram
The following symbols apply to the circuit diagram and equations:
•
R1 and R2 are half-bridge completion resistors.
•
R3 is the active element measuring compression from Poisson
effect (–νε).
•
R4 is the active element measuring tensile strain (+ε).
•
VEX is the excitation voltage.
•
RL is the lead resistance.
•
VCH is the measured voltage.
As shown in Figure 2-4, for greatest calibration accuracy, use separate wires
between the bridge and the SCA terminals. Do not directly connect S+ or P– to the
SCA terminals inside the SCXI-1314 terminal block unless the strain-gauge cable
length is very short.
Note
SCXI-1520 User Manual
2-4
ni.com
Chapter 2
Connecting Signals
Half-Bridge Type II
This section provides information for connecting the half-bridge
strain-gauge configuration type II. Figure 2-4 shows the half-bridge type II
circuit wiring diagram.
Note
S– is left unwired.
Transducer
SCXI-1314
RL
SCXI-1520 Set Bridge
Configuration to Half Bridge
S+
VCH
RL
R4
(gauge)
R3
(gauge)
+
–
P+
R1
+
Vout +
–
–
VEX
R2
P
RL
+
Vout
SCA
Shunt
Cal A
RL
SCA
RL
RS
Figure 2-4. Half-Bridge Type II Circuit Diagram
The following symbols apply to the circuit diagram and equations:
•
R1 and R2 are half-bridge completion resistors.
•
R3 is the active element measuring compressive strain (–ε).
•
R4 is the active element measuring tensile strain (+ε).
•
VEX is the excitation voltage.
•
RL is the lead resistance.
•
VCH is the measured voltage.
As shown in Figure 2-3, for greatest calibration accuracy, use separate wires
between the bridge and the SCA terminals. Do not directly connect S+ or P– to the
SCA terminals inside the SCXI-1314 terminal block unless the strain-gauge cable
length is very short.
Note
© National Instruments Corporation
2-5
SCXI-1520 User Manual
Chapter 2
Connecting Signals
Full-Bridge Type I
This section provides information for connecting the full-bridge
strain-gauge configuration type I. Figure 2-5 shows the full-bridge type I
circuit wiring diagram.
Transducer
SCXI-1314
SCXI-1520 Set Bridge
Configuration to Full Bridge
S+
VCH
S
RL
VEX +
CH+
R3
VEX
+
CH
+
R2
–
RL
–
P+
R1
–
R4
+
+
–
P
SCA
RL
Shunt
Cal A
SCA
RL
RS
Figure 2-5. Full-Bridge Type I Circuit Diagram
The following symbols apply to the circuit diagram and equations:
•
R1 is an active element measuring compressive strain (–ε).
•
R2 is an active element measuring tensile strain (+ε).
•
R3 is an active element measuring compressive strain (–ε).
•
R4 is an active element measuring tensile strain (+ε).
•
VEX is the excitation voltage.
•
RL is the lead resistance.
•
VCH is the measured voltage.
As shown in Figure 2-5, for greatest calibration accuracy, use separate wires
between the bridge and the SCA terminals. Do not directly connect S+ or P– to the
SCA terminals inside the SCXI-1314 terminal block unless the strain-gauge cable
length is very short.
Note
SCXI-1520 User Manual
2-6
ni.com
Chapter 2
Connecting Signals
Full-Bridge Type II
This section provides information for connecting the full-bridge
strain-gauge configuration type II. Figure 2-6 shows the full-bridge type II
circuit wiring diagram.
Transducer
SCXI-1314
SCXI-1520 Set Bridge
Configuration to Full Bridge
S+
VCH
S
VEX +
R4
+
–
R3
VEX–
RL
RL
–
P+
R1
–v
+v
R2
+
+
–
P
SCA
Shunt
Cal A
RL
SCA
RL
RS
Figure 2-6. Full-Bridge Type II Circuit Diagram
The following symbols apply to the circuit diagram and equations:
•
R1 is an active element measuring compressive Poisson effect (–νε).
•
R2 is an active element measuring tensile Poisson effect (+νε).
•
R3 is an active element measuring compressive strain (–ε).
•
R4 is an active element measuring tensile strain (+ε).
•
VEX is the excitation voltage.
•
RL is the lead resistance.
•
VCH is the measured voltage.
As shown in Figure 2-6, for greatest calibration accuracy, use separate wires
between the bridge and the SCA terminals. Do not directly connect S+ or P– to the
SCA terminals inside the SCXI-1314 terminal block unless the strain-gauge cable
length is very short.
Note
© National Instruments Corporation
2-7
SCXI-1520 User Manual
Chapter 2
Connecting Signals
Full-Bridge Type III
This section provides information for connecting the full-bridge
strain-gauge configuration type I. The full-bridge type III only measures
axial strain. Figure 2-7 shows the full-bridge type III circuit wiring
diagram.
SCXI-1314
Transducer
SCXI-1520 Set Bridge
Configuration to Full Bridge
S+
VCH
S
VEX +
R4
+
+
–
P+
R1
–v
+
–
–v
R3
VEX–
+
R2
P
SCA
Shunt
Cal A
RL
SCA
RS
RL
Figure 2-7. Full-Bridge Type III Circuit Diagram
The following symbols apply to the circuit diagram and equations:
•
R1 is an active element measuring compressive Poisson effect (–νε).
•
R2 is an active element measuring tensile strain (+ε).
•
R3 is an active element measuring compressive Poisson effect (–νε).
•
R4 is an active element measuring the tensile strain (+ε).
•
VEX is the excitation voltage.
•
RL is the lead resistance.
•
VCH is the measured voltage.
As shown in Figure 2-7, for greatest calibration accuracy, use separate wires
between the bridge and the SCA terminals. Do not directly connect S+ or P– to the
SCA terminals inside the SCXI-1314 terminal block unless the strain-gauge cable
length is very short.
Note
SCXI-1520 User Manual
2-8
ni.com
Chapter 2
Connecting Signals
Remote Sense
NI recommends using remote sense if your application requires the improved
accuracy. Refer to Chapter 4, Theory of Operation, for more information about using
remote sense.
Note
Wire the SCXI-1520 for remote sense as shown in Figure 2-8.
Transducer
SCXI-1314
SCXI-1520
Run Separate Wires
Between Remote-Sense
Terminals and Bridge
RS+
VEX +
R1
P+
R4
+
–
R2
VEX–
R3
Feedback
P
RS
Figure 2-8. Remote-Sense Circuit Diagram
Note
If you use remote sense, set RL to zero in the equations for measured strain (ε).
© National Instruments Corporation
2-9
SCXI-1520 User Manual
Chapter 2
Connecting Signals
Pin Assignments
The pin assignments for the SCXI-1520 front signal connector are shown
in Table 2-1. The front signal connector is a special 96-pin DIN C male
connector through which you make all signal connections. The terminal
assignments are as follows:
•
SX+ and SX– are for analog input
•
RSX+ and RSX– are for remote sense
•
PX+ and PX– are for excitation output
•
SCAX are for shunt calibration circuit A
•
SCBX are for shunt calibration circuit B
where X is the channel number.
The negative terminals are listed in Column B and the positive terminals are
listed in Column C. The pins labeled RSVD are reserved. Do not make any
connections to the RSVD pins.
SCXI-1520 User Manual
2-10
ni.com
Chapter 2
Connecting Signals
Table 2-1. Front Signal Pin Assignments
Front Connector Diagram
Pin Number
Column A
Column B
Column C
32
SCB0
S0–
S0+
31
SCB0
RS0–
RS0+
30
SCB1
P0–
P0+
32
29
SCB1
SCA0
SCA0
31
28
RSVD
S1–
S1+
27
RSVD
RS1–
RS1+
26
RSVD
P1–
P1+
27
25
RSVD
SCA1
SCA1
26
24
SCB2
S2–
S2+
25
23
SCB2
RS2–
RS2+
22
SCB3
P2–
P2+
21
SCB3
SCA2
SCA2
21
20
RSVD
S3–
S3+
20
19
RSVD
RS3–
RS3+
19
18
RSVD
P3–
P3+
17
RSVD
SCA3
SCA3
16
SCB4
S4–
S4+
15
15
SCB4
RS4–
RS4+
14
14
SCB5
P4–
P4+
13
13
SCB5
SCA4
SCA4
12
RSVD
S5–
S5+
11
RSVD
RS5–
RS5+
9
10
RSVD
P5–
P5+
8
9
RSVD
SCA5
SCA5
7
8
SCB6
S6–
S6+
7
SCB6
RS6–
RS6+
4
6
SCB7
P6–
P6+
3
5
SCB7
SCA6
SCA6
2
4
RSVD
S7–
S7+
3
RSVD
RS7–
RS7+
2
RSVD
P7–
P7+
1
RSVD
SCA7
SCA7
A
Column
B
C
30
29
28
24
23
22
18
17
16
12
11
10
6
5
1
© National Instruments Corporation
2-11
SCXI-1520 User Manual
Chapter 2
Connecting Signals
The rear signal connector is a 50-pin male cable connector used for analog
signal connectivity and communication between the SCXI-1520 and the
connected E/M Series DAQ device. The rear signal connector is shown in
Table 2-2. The rear signal connector allows the DAQ device to access all
eight differential analog output signals from the SCXI-1520. The positive
terminal of each analog output is named CHX+ and the negative terminal
CHX–.
SCXI-1520 User Manual
2-12
ni.com
Chapter 2
Connecting Signals
Table 2-2. Rear Signal Pin Assignments
Rear Connector
Diagram
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
Signal Name
Pin Number
Pin Number
Signal Name
—
1
2
—
CH 0 +
3
4
CH 0 –
CH 1 +
5
6
CH 1 –
CH 2 +
7
8
CH 2 –
CH 3 +
9
10
CH 3 –
CH 4 +
11
12
CH 4 –
CH 5 +
13
14
CH 5 –
CH 6 +
15
16
CH 6 –
CH 7 +
17
18
CH 7 –
—
19
20
—
—
21
22
—
—
23
24
DIG GND
SER DAT IN
25
26
SER DAT OUT
DAQ D*/A
27
28
—
SLOT 0 SEL*
29
30
—
—
31
32
—
DIG GND
33
34
—
—
35
36
AI HOLD COMP, AI HOLD
SER CLK
37
38
—
—
39
40
—
—
41
42
—
—
43
44
—
—
45
46
SYNC
—
47
48
—
—
49
50
—
In parallel output mode, channel 0 is selected at the output multiplexer and
is connected to CH 0. The seven other channels are directly connected to
CH 1 through CH 7, respectively, on the rear connector.
© National Instruments Corporation
2-13
SCXI-1520 User Manual
Chapter 2
Connecting Signals
In multiplexed mode, the CH 0 signal pair is used for sending all eight
channels of the SCXI-1520, and analog signals from other modules, to the
connected E/M Series DAQ device. If the module is cabled directly to the
DAQ device, the other analog channels of the DAQ device are unavailable
for general-purpose analog input because they are connected to the
SCXI-1520 amplifier outputs. This means that connecting an SCXI-1180
module to the 50-pin breakout connector of the SCXI-1349, or other cable
adapter assembly, may cause interference and incorrect measurements
when the DAQ device is cabled to the SCXI-1520.
The communication signals between the DAQ device and the SCXI system
are listed in Table 2-3. If the DAQ device is connected to the SCXI-1520,
these digital lines are unavailable for general-purpose digital I/O.
Table 2-3. SCXI-1520 Communication Signals
Pin
SCXI
Signal Name
NI-DAQmx
Device Signal
Name
Traditional NI-DAQ
(Legacy) Device
Signal Name
Direction
Description
24, 33
DIG GND
D GND
DGND
—
Digital ground—these
pins supply the
reference for
E/M Series DAQ device
digital signals and are
connected to the
module digital ground.
25
SER DAT IN
P0.0
DIO0
Input
Serial data in—this
signal taps into the
SCXIbus MOSI line to
send serial input data to
a module or Slot 0.
26
SER DAT OUT
P0.4
DIO4
Output
Serial data out—this
signal taps into the
SCXIbus MISO line to
accept serial output data
from a module.
27
DAQ D*/A
P0.1
DIO1
Input
Board data/address
line—this signal taps
into the SCXIbus D*/A
line to indicate to the
module whether the
incoming serial stream
is data or address
information.
SCXI-1520 User Manual
2-14
ni.com
Chapter 2
Connecting Signals
Table 2-3. SCXI-1520 Communication Signals (Continued)
Pin
SCXI
Signal Name
NI-DAQmx
Device Signal
Name
Traditional NI-DAQ
(Legacy) Device
Signal Name
Direction
Description
29
SLOT0SEL*
P0.2
DIO2
Input
Slot 0 select—this
signal taps into the
SCXIbus INTR* line to
indicate whether the
information on MOSI is
being sent to a module
or Slot 0.
36
SCANCLK
AI HOLD COMP,
AI HOLD
SCANCLK
Input
Scan clock—a rising
edge indicates to the
scanned SCXI module
that the E/M Series
DAQ device has taken a
sample and causes the
module to advance
channels.
37
SER CLK
EXTSTROBE*
EXTSTROBE*
Input
Serial clock—this
signal taps into the
SCXIbus SPICLK line
to clock the data on the
MOSI and MISO lines.
46
HOLD TRIG
PFI 7/
AI SAMP CLK,
AI SAMP
PFI7/
START SCAN
Input
Hold trigger—this
signal is used by the
MIO to set the
track-and-hold state of
the module.
© National Instruments Corporation
2-15
SCXI-1520 User Manual
Configuring and Testing
3
This chapter discusses configuring the SCXI-1520 in MAX for use with
either NI-DAQmx or Traditional NI-DAQ (Legacy), creating and testing a
virtual channel, global channel, and/or task.
SCXI-1520 Software-Configurable Settings
This section describes how to set the bridge configuration, voltage
excitation level, filter bandwidth, and gain/input signal range, as well as
how to use configuration utilities in MAX to programmatically perform
offset null compensation and shunt calibration. It also describes how to
perform configuration of these settings for the SCXI-1520 in NI-DAQmx
and Traditional NI-DAQ (Legacy). For more information on the
relationship between the settings and the measurements, and how to
configure settings in your application, refer to Chapter 4, Theory of
Operation.
Common Software-Configurable Settings
This section describes the most frequently used software-configurable
settings for the SCXI-1520. Refer to Chapter 4, Theory of Operation,
for a complete list of software-configurable settings.
Bridge Configuration
Bridge configuration is a software-configurable setting that allows you to
connect quarter-, half-, or full-bridge configuration Wheatstone bridge
sensors easily. When quarter- or half-bridge configuration is selected,
Terminal SX– (where X is a particular channel) is disconnected from the
front signal connector and internally connected to a half-bridge completion
network. Implementing quarter-bridge completion also involves making
field wiring connections to the quarter-bridge completion resistor (QTR) in
the terminal block.
© National Instruments Corporation
3-1
SCXI-1520 User Manual
Chapter 3
Configuring and Testing
Excitation Level
Excitation level is a software-configurable setting that allows you to set the
voltage excitation level available on PX+ and PX– (where X is a particular
channel). You can choose voltage excitation settings between 0 and 10 V.
To prevent the module from overheating, do not set the excitation voltage
greater than
(resistance connected between the excitation terminals) × (29.0 mA)
You need not include the loading effect of the internal half-bridge completion
resistors in the above calculation. When using internal quarter-bridge completion you must
include the nominal gauge resistance as well as the quarter-bridge completion resistance
(R3 + R4).
Note
Table 3-1 shows the maximum allowable excitation voltages for standard
bridge configurations and resistances.
Table 3-1. Excitation Voltage for Configuration and Gauge Resistances
Configuration/
Sensor
Quarter- or
Half-Bridge
Full-Bridge or
Full-Bridge Sensor
Resistance
NI-DAQmx Excitation
Voltage Range
Traditional NI-DAQ
(Legacy) Excitation
Voltage Range
120 Ω
≤6.96 V
0 to 6.875 V
350 Ω
0 to 10 V
0 to 10 V
1000 Ω
0 to 10 V
0 to 10 V
120 Ω
≤3.48 V
0 to 3.125 V
350 Ω
0 to 10 V
0 to 10 V
1000 Ω
0 to 10 V
0 to 10 V
Filter Bandwidth
Filter bandwidth is a software-configurable setting that allows you to select
a lowpass filter cutoff frequency. You can choose 10 Hz, 100 Hz, 1 kHz,
10 kHz, or filter-bypass mode. If your application requires other cutoff
frequencies, refer to Chapter 4, Theory of Operation.
SCXI-1520 User Manual
3-2
ni.com
Chapter 3
Configuring and Testing
Gain/Input Range
Gain/input range is a software-configurable setting that allows you to
choose the appropriate amplification to fully utilize the range of the
E/M Series DAQ device. In most applications NI-DAQ chooses and sets
the gain for you determined by the input range. This feature is described in
Chapter 4, Theory of Operation. Otherwise, you should determine the
appropriate gain using the input signal voltage range and the full-scale
limits of the SCXI-1520 output signal. For common strain-gauge
configurations where the Gauge Factor is 2.0, the maximum input signal
(in microvolts) is:
quarter bridge = (max strain) × (excitation voltage) × (0.5 μV/V/με)
half bridge = (max strain) × (excitation voltage) × (1.0 μV/V/με)
full bridge = (max strain) × (excitation voltage) × (2.0 μV/V/με)
When you have determined the input signal voltage you can use the
following equation to determine the appropriate gain:
( SCXI-1520 output voltage range ) × ( 10 V )
gain ≤ ---------------------------------------------------------------------------------------------------------( input signal voltage )
If you are using a bridge-based sensor, use the manufacturer-specified
sensitivity (usually expressed in the units of millivolts per volt) to
determine the maximum input signal. The maximum input signal is:
sensitivity) × (excitation voltage) × (maximum input)
(max input signal voltage) = (sensor
------------------------------------------------------------------------------------------------------------------------------------------------(sensor full-scale input)
For example, if you have a 0 to 500 psi pressure sensor with 3.0 mV/V
sensitivity, an excitation voltage of 10 V, and a maximum pressure of
200 psi, the maximum signal is:
( 3.0 mV/V ) × ( 10 V ) × ( 200 psi )
12 mV = -------------------------------------------------------------------------------( 500 psi )
© National Instruments Corporation
3-3
SCXI-1520 User Manual
Chapter 3
Configuring and Testing
If you are using a DAQ device that has a maximum analog input range of
±10 V and you have a maximum input to the SCXI-1520 of +12 mV, set the
gain to the setting closest to
10 V
833 = ---------------12 mV
but less than 833. A larger gain setting saturates the DAQ device input for
a 12 mV signal. In this example, the closest lesser gain setting for the
SCXI-1520 is 750.
Null Potentiometers
Coarse and fine null potentiometers are software-configurable settings that
allow you to remove unwanted offset voltage. In most cases, you do not
explicitly set the null potentiometers, but instead allow driver software to
automatically adjust them for you. However, if you want to explicitly set
the null potentiometers, you can write an application program that adjusts
the null potentiometers settings. Refer to Chapter 4, Theory of Operation,
for more information.
Shunt Calibration Switches
Shunt calibration switches A and B are software control settings that allow
you to engage or disengage the shunt calibration resistors in order to
perform gain calibration. In most cases, you do not explicitly control
the shunt calibration switches, but instead allow driver software to
automatically adjust them for you during the automated shunt calibration
procedure. However, if you want to explicitly control the calibration
switches, you can write an application program that controls the shunt
calibration switches. Refer to Chapter 4, Theory of Operation, for more
information.
The gain adjustment is done for you automatically if you have performed shunt
calibration using the NI-DAQ driver. Refer to the Traditional NI-DAQ (Legacy) section
and the NI-DAQmx section for more information about how to perform shunt calibration
using the driver.
Note
SCXI-1520 User Manual
3-4
ni.com
Chapter 3
Configuring and Testing
Modes of Operation
The SCXI-1520 can operate in multiplexed mode or parallel mode. Using
NI-DAQmx, you can operate the SCXI-1520 in either multiplexed or
parallel mode. In Traditional NI-DAQ (Legacy), only multiplexed mode is
supported. Refer to the Strain-Gauge Theory section of Chapter 4, Theory
of Operation, for more information on multiplexed and parallel mode
operation.
Simultaneous Sample and Hold
When it is critical to measure two or more signals at the same instant
in time, simultaneous sample and hold (SS/H) is required. Typical
applications that might require SS/H include vibration measurements
and phase difference measurements. In NI-DAQmx, you can disable this
setting through your application if you require scan rates beyond the
maximum allowable with SS/H engaged. NI recommends leaving SS/H
engaged.
You cannot change the simultaneous sampling mode in MAX. You must use an ADE
such as LabVIEW or LabWindows/CVI to configure the setting using NI-DAQmx Channel
Property Node. Refer to your ADE help file for more information.
Note
Configurable Settings in MAX
If you are not using an NI ADE, using an NI ADE prior to version 7.0, or are using
an unlicensed copy of an NI ADE, additional dialog boxes from the NI License Manager
appear allowing you to create a task or global channel in unlicensed mode. These messages
continue to appear until you install version 7.0 or later of an NI ADE.
Note
This section describes where you can access each software-configurable
setting for modification in MAX. The location of the settings varies
depending on the version of NI-DAQ you use. Refer to either the
NI-DAQmx section or the Traditional NI-DAQ (Legacy) section. You also
can refer to the DAQ Getting Started Guide and the SCXI Quick Start Guide
for more information on installing and configuring the hardware. You also
can use the DAQ Assistant to graphically configure common measurement
tasks, channels, or scales.
© National Instruments Corporation
3-5
SCXI-1520 User Manual
Chapter 3
Configuring and Testing
NI-DAQmx
In NI-DAQmx, you can configure software settings such as bridge
configuration, voltage excitation level, filter bandwidth, gain/input signal
range, and calibration settings in the following two ways:
•
Task or global channel in MAX
•
Functions in your application
All software-configurable settings are not configurable both ways. This section only
discusses settings in MAX. Refer to Chapter 4, Theory of Operation, for information on
using functions in your application.
Note
These sections describe settings that you can change in MAX and where
they are located. Strain and custom voltage with excitation are the most
commonly used NI-DAQmx Task or NI-DAQmx Global Channel types
with the SCXI-1520. Use the Custom Voltage with Excitation
NI-DAQmx task or global channel when measuring load, force, torque,
pressure, or other bridge-based sensors:
SCXI-1520 User Manual
•
Bridge configuration—configure using the settings tab of NI-DAQmx
Task or NI-DAQmx Global Channel and functions in your
application. Channel properties override module properties.
The default bridge configuration for NI-DAQmx is full bridge.
•
Voltage excitation—configure using either NI-DAQmx Task or
NI-DAQmx Global Channel. You also can set the voltage excitation
level through your application. In NI-DAQmx, you can choose from
contiguous voltages between 0 and 10 V. The default voltage
excitation in NI-DAQmx is 0 V.
•
Filter bandwidth—configure the Device tab using either NI-DAQmx
Task or NI-DAQmx Global Channel. You also can set the value
through your application. The default filter cut-off frequency in
NI-DAQmx is 10 kHz.
•
Input signal range—configure the input signal range using either
NI-DAQmx Task or NI-DAQmx Global Channel. When you set the
minimum and maximum range of NI-DAQmx Task or NI-DAQmx
Global Channel, the driver selects the best gain for the measurement.
You also can set it through your application. The default gain setting in
NI-DAQmx is 1.0. This setting corresponds to an input range of ±10 V.
•
Calibration settings—null potentiometer settings and control shunt
calibration switches only using Strain NI-DAQmx Task, Strain
NI-DAQmx Global Channel, or your application. The Custom
Voltage with Excitation NI-DAQmx Task or NI-DAQmx Global
Channel cannot adjust calibration settings in MAX. Adjust calibration
3-6
ni.com
Chapter 3
Configuring and Testing
settings in your application. The default configuration settings set the
null potentiometers at their midpoint, 62 for the coarse potentiometer
and 2,047 for the fine potentiometer. The default state of the shunt
calibration switches is open. This state leaves the shunt calibration
resistor disconnected from the circuit.
•
Modes of operation—configure only using chassis installation in
software. Refer to Chapter 1, About the SCXI-1520, for more
information on chassis installation. The default setting in NI-DAQmx
is multiplexed.
•
Simultaneous sample-and-hold settings—configure only using your
application. The default setting in NI-DAQmx engages SS/H.
Refer to Chapter 4, Theory of Operation, for information on configuring the settings
for your application using Traditional NI-DAQ (Legacy).
Note
Creating a Strain Global Channel or Task
To create a new NI-DAQmx strain global task or channel, complete the
following steps:
1.
Double-click Measurement & Automation on the desktop.
2.
Right-click Data Neighborhood and select Create New.
3.
Select NI-DAQmx Task or NI-DAQmx Global Channel, and
click Next.
4.
Select Analog Input.
5.
Select Strain.
6.
If you are creating a task, you can select a range of channels by holding
down the <Shift> key while selecting the channels. You can select
multiple individual channels by holding down the <Ctrl> key while
selecting channels. If you are creating a channel, you can only select
one channel. Click Next.
7.
Name the task or channel and click Finish.
8.
In the Channel List box, select the channel(s) you want to configure.
You can select a range of channels by holding down the <Shift> key
while selecting the channels. You can select multiple individual
channels by holding down the <Ctrl> key while selecting channels.
9.
Enter the specific values for your application in the Settings tab.
Context help information for each setting is provided on the right side
of the screen.
10. Click the Device tab and select the autozero mode and lowpass filter
cutoff frequency.
© National Instruments Corporation
3-7
SCXI-1520 User Manual
Chapter 3
Configuring and Testing
11. Ensure that you have selected the strain channel(s) you wish to
calibrate in the Channel List box. Click Calibration to calibrate the
strain channel(s).
12. On the screen that appears choose to enable offset nulling and/or
shunt calibration. Enter the shunt calibration resistor information.
Click Next.
13. Measure and Calibrate displays information specific to the strain
channel(s). Click Measure to acquire a signal from the strain
channel(s) and Reset Data to reset the values to default. Click
Calibrate to calibrate the strain channel(s). When you have completed
calibrating the strain channel(s), click Finish.
14. If you are creating a task and want to set timing or triggering controls,
enter the values in the Task Timing and Task Triggering tabs.
Creating a Custom Voltage with Excitation Global
Channel or Task
Use the Custom Voltage with Excitation NI-DAQmx Task or Global
Channel when measuring load, force, torque, pressure, or other
bridge-based sensors. To create an NI-DAQmx Custom Voltage
with Excitation Task or NI-DAQmx Global Channel, complete the
following steps:
SCXI-1520 User Manual
1.
Double-click Measurement & Automation on the desktop.
2.
Right-click Data Neighborhood and select Create New.
3.
Select NI-DAQmx Global Channel or NI-DAQmx Task, and
click Next.
4.
Select Analog Input then select Custom Voltage with Excitation.
5.
If you are creating a channel, you can select only one channel. If you
are creating a task, select the channels to add to the task. You can select
a range of channels by holding down the <Shift> key while selecting
the channels. You can select multiple individual channels by holding
down the <Ctrl> key while selecting channels. Click Next.
6.
Select the name of the task or channel, and click Finish.
7.
In the Channel List box, select the channel(s) you want to configure.
You can select a range of channels by holding down the <Shift> key
while selecting the channels. You can select multiple individual
channels by holding down the <Ctrl> key while selecting channels.
8.
Enter the specific values for your application in the Settings tab.
Context help information for each setting is provided on the right side
of the screen.
3-8
ni.com
Chapter 3
9.
Configuring and Testing
Click the Device tab and select the autozero mode and lowpass filter
cutoff frequency.
10. If you are applying custom scaling, select the Create New drop-down
and follow the onscreen wizard.
11. If you are creating a task and want to set timing or triggering controls,
enter the values in the Task Timing and Task Triggering tabs.
Traditional NI-DAQ (Legacy)
In Traditional NI-DAQ (Legacy), you can configure software settings,
such as bridge configuration, voltage excitation level, filter bandwidth,
gain/input signal range, and calibration settings, in the following
three ways:
•
module property pages in MAX
•
virtual channels properties in MAX
•
functions in your ADE
All software-configurable settings are not configurable in all three ways. This
section only discusses settings in MAX. Refer to Chapter 4, Theory of Operation, for
information on using functions in your application.
Note
Most of these settings are available in module properties and/or using
virtual channels:
•
Bridge configuration—configure using module properties, virtual
channels properties, and functions in your application. Virtual
channel properties override module properties. The default bridge
configuration for Traditional NI-DAQ (Legacy) is quarter bridge.
•
Voltage excitation—configure using module properties or virtual
channel properties. Virtual channel properties override module
properties settings. You also can set excitation through your
application. You can choose one of 17 voltage settings between
0 and 10 V. The default voltage excitation level for Traditional
NI-DAQ (Legacy) is 2.5 V.
•
Filter bandwidth—configure only using module properties. You also
can set bandwidth through your application. The default filter
bandwidth level for Traditional NI-DAQ (Legacy) is 10 Hz.
•
Gain/input signal range—configure gain using module properties.
When you set the minimum and maximum range of the virtual
channel, the driver selects the best gain. The default gain setting
for Traditional NI-DAQ (Legacy) is 100.
© National Instruments Corporation
3-9
SCXI-1520 User Manual
Chapter 3
Configuring and Testing
•
Calibration settings—configure null potentiometer settings and
control shunt calibration switches only using strain virtual channel or
using your application. The default configuration settings set the null
potentiometers at their midpoint, 62 for the coarse potentiometer
and 2,047 for the fine potentiometer. The default state of the shunt
calibration switches is open. This state leaves the shunt calibration
resistor disconnected from the circuit.
•
Modes of operation—configure only using module properties. The
default setting in Traditional NI-DAQ (Legacy) is multiplexed mode.
Parallel mode is not supported in Traditional NI-DAQ (Legacy).
•
Simultaneous sample-and-hold settings—can modify this setting only
using NI-DAQmx.
Refer to Chapter 4, Theory of Operation, for information on configuring the settings
for your application using Traditional NI-DAQ (Legacy).
Note
Configuring Module Property Pages in Traditional
NI-DAQ (Legacy)
1.
Right-click the SCXI-1520 module you want to configure and select
Properties. Click General.
2.
If the module you are configuring is connected to an E Series DAQ
device, select that device by using Connected to. If you want this DAQ
device to control the chassis, confirm there is a check in the This
device will control the chassis checkbox. If the module you are
configuring is not connected to an DAQ device, select None.
3.
Click the Channel tab. Select the appropriate gain, filter, voltage
excitation, and bridge configuration setting for each channel. If you
want to configure all the channels at the same time, select the Channel
drop-down menu, scroll to the bottom, and select All Channels. Refer
to the SCXI-1520 Software-Configurable Settings section for a
detailed description of each setting. Click Apply.
4.
Click Accessory. Select the accessory you connected to the module.
When configuration is complete, click OK.
The Traditional NI-DAQ (Legacy) chassis and SCXI-1520 should now
be configured properly. If you need to change the module configuration,
right-click the module and repeat steps 1 through 4. Test the system
following the steps in the Troubleshooting the Self-Test Verification
section of Chapter 1, About the SCXI-1520.
SCXI-1520 User Manual
3-10
ni.com
Chapter 3
Configuring and Testing
Creating a Strain Virtual Channel
To create a strain virtual channel, complete the following steps:
1.
Right-click Data Neighborhood and select Create New.
2.
Select Traditional NI-DAQ Virtual Channel and click Finish.
3.
Click Add Channel.
4.
Select Analog Input from the drop-down menu and click Next.
5.
Enter the Channel Name and Channel Description, and click Next.
6.
Select Strain Gauge from the drop-down menu and click Next.
7.
Enter the following information:
a.
Bridge type from the drop-down menu
b.
V init in volts
c.
Lead Resistance in Ω
d.
Nominal Gauge in Ω
e.
Gauge Factor
f.
Range min in με
g.
Range max in με
8.
Click Next.
9.
Enter the following information:
a.
What DAQ hardware will be used? from the drop-down menu
b.
What channel on your DAQ hardware? from the drop-down
menu
c.
Which analog input mode will be used? from the drop-down
menu
d.
What is the Excitation Voltage’s source and value? from the
drop-down menu
e.
Voltage in volts
10. Click Finish.
Calibrating a Strain Virtual Channel
To calibrate a strain virtual channel, complete the following steps:
1.
Right-click the virtual channel you want to calibrate and select
Properties.
2.
Click Calibration.
3.
Select the Engineering Units from the drop-down menu.
© National Instruments Corporation
3-11
SCXI-1520 User Manual
Chapter 3
Configuring and Testing
4.
Enter the Calibration Data and click Update.
5.
Make the selections in Shunt Cal Circuit A and Operation, and
click Start.
6.
After the calibration is completed, click Exit.
Verifying the Signal
This section describes how to take measurements using test panels in order
to verify signal, and configuring and installing a system in NI-DAQmx and
Traditional NI-DAQ (Legacy).
Verifying the Signal in NI-DAQmx Using a Task or Global Channel
You can verify the signals on the SCXI-1520 using NI-DAQmx by
completing the following steps:
1.
Expand the list of tasks and virtual channels by clicking the + next to
Data Neighborhood.
2.
Click the + next to NI-DAQmx Tasks to expand the list of tasks.
3.
Click the task.
4.
Add or remove channels, if applicable, in the Channel List. Click the
Add Channels button, shown at left, and select the type of channel you
want to add.
a.
In the window that appears, expand the list of channels by clicking
the + next to the module of interest.
b.
Select the channel(s) you want to verify. You can select a block of
channels by holding down the <Shift> key or multiple channels by
holding down the <Ctrl> key. Click OK.
5.
Enter the appropriate information on the Settings tab.
6.
Click the Device tab and enter the appropriate information on the
Device tab.
7.
Click the Test button to open the test panel.
8.
Click the Start button, if necessary.
9.
After you have completed verifying the channels, close the test panel
window.
You have now verified the SCXI-1520 configuration and signal connection.
SCXI-1520 User Manual
3-12
ni.com
Chapter 3
Configuring and Testing
For more information on how to further configure the SCXI-1520, or how to use
LabVIEW to configure the module and take measurements, refer to Chapter 4, Theory of
Operation.
Note
Verifying the Signal in Traditional NI-DAQ (Legacy)
This section discusses how to verify the signal in Traditional NI-DAQ
(Legacy) using channel strings and virtual channels.
Verifying the Signal Using Channel Strings
The format of the channel string is as follows:
obx ! scy ! mdz ! channel
where
obx is the onboard E Series DAQ device channel, with x representing
a particular channel where the multiplexed channels are sent. This
value is 0 for DAQ device channel 0 in a single-chassis system. In a
multichassis or remote chassis system, the DAQ device channel x
corresponds to chassis number n – 1, where DAQ device channel x is
used for scanning the nth chassis in the system.
scy is the SCXI chassis ID, where y is the number you chose when
configuring the chassis.
mdz is the slot position where the module is located, with z being the
particular slot number. The slots in a chassis are numbered from left to
right, starting with 1.
channel is the channel that is sampled from module z.
Use the format obx ! scy ! mdz ! n to verify the signal, where n is a
single input channel.
Complete the following steps to use channel strings in verifying the signal:
1.
Expand the list of tasks and virtual channels by clicking the + next to
Devices and Interfaces.
2.
Click the + next to Traditional NI-DAQ Devices to expand the
device list.
3.
Right-click the appropriate E Series DAQ device.
4.
Click Test Panels.
5.
Enter the channel string.
6.
Enter the input limits.
© National Instruments Corporation
3-13
SCXI-1520 User Manual
Chapter 3
Configuring and Testing
7.
Select the Data Mode.
8.
Select the Y Scale Mode.
Refer to the LabVIEW Measurements Manual for more information and for
proper formatting of channel strings for different uses.
Verifying the Signal Using Strain Virtual Channel
If you have already created a virtual channel, complete the following steps
to verify the signal:
1.
Right-click the strain virtual channel you want to verify and
select Test.
2.
In Channel Names, select the channel you want to verify.
3.
When you have completed verifying the channel, click Close.
Using the Strain Calibration Wizard in NI-DAQmx
When using NI-DAQmx, you can perform an automated strain calibration
on one or more channels in your task using the Strain Calibration Wizard
in MAX.
Note
All channels must be strain channels to use the Strain Calibration Wizard.
Complete the following steps to perform calibration using the Calibration
Wizard:
SCXI-1520 User Manual
1.
Expand the list of devices by clicking the + next to Data
Neighborhood.
2.
Click the + next to NI-DAQmx Tasks to expand the list of tasks.
3.
Select the strain task you previously created.
4.
Click the Device tab.
5.
Select the Auto Zero Mode and Lowpass Filter Cutoff Frequency
from the dropdown lists.
6.
Click the Calibration button and follow the onscreen instructions.
3-14
ni.com
4
Theory of Operation
This chapter discusses strain-gauge concepts and the theory of operational
measurement concepts.
Strain-Gauge Theory
This section discusses how to arrange, connect, and scale signals from
bridge-based sensors, especially strain gauges.
Wheatstone Bridges
All strain-gauge configurations are based on the concept of a Wheatstone
bridge. A Wheatstone bridge is a network of four resistive legs. One or
more of these legs can be active sensing elements. Figure 4-1 shows a
Wheatstone bridge circuit diagram.
VEX +
R4
R1
– VCH +
R2
R3
Figure 4-1. Basic Wheatstone Bridge Circuit Diagram
The Wheatstone bridge is the electrical equivalent of two parallel voltage
divider circuits. R1 and R2 compose one voltage divider circuit, and R4 and
R3 compose the second voltage divider circuit. The output of a Wheatstone
bridge is measured between the middle nodes of the two voltage dividers.
© National Instruments Corporation
4-1
SCXI-1520 User Manual
Chapter 4
Theory of Operation
A physical phenomena, such as a change in strain or temperature applied
to a specimen, changes the resistance of the sensing elements in the
Wheatstone bridge. The Wheatstone bridge configuration is used to help
measure the small variations in resistance that the sensing elements
produce corresponding to a physical changes in the specimen.
Strain Gauges
Strain-gauge configurations are arranged as Wheatstone bridges. The
gauge is the collection of all of the active elements of the Wheatstone
bridge. There are three types of strain-gauge configurations: quarter-, half-,
and full-bridge. The number of active element legs in the Wheatstone
bridge determines the kind of bridge configuration. Table 4-1 shows the
number of active elements in each configuration.
Table 4-1. Strain-Gauge Configurations
Configuration
Number of Active Elements
Quarter-bridge
1
Half-bridge
2
Full-bridge
4
Each of these configurations is subdivided into multiple configuration
types. The orientation of the active elements and the kind of strain
measured determines the configuration type. NI supports seven
configuration types in software. However, with custom software scaling
you can use all Wheatstone bridge configuration types with any
NI hardware product that supports the gauge configuration type.
The supported strain-gauge configuration types measure axial strain,
bending strain, or both. While you can use some similar configuration types
to measure torsional strain, NI software scaling does not support these
configuration types. It is possible to use NI products to measure torsional
strain, but to properly scale these configuration types you must create a
custom scale in MAX or perform scaling in your software application.
This document discusses all of the mechanical, electrical, and scaling
considerations of each strain-gauge configuration type supported by NI.
SCXI-1520 User Manual
4-2
ni.com
Chapter 4
Theory of Operation
Acronyms, Formulas, and Variable Definitions
In the figures and equations in this document, the acronyms, formulas, and
variables are defined as follows:
ε is the measured strain (+ε is tensile strain and –ε is compressive strain).
εS is the simulated strain.
GF is the Gauge Factor, which should be specified by the gauge
manufacturer.
Rg is the nominal gauge resistance, which should be specified by the gauge
manufacturer.
RL is the lead resistance. If lead lengths are long, RL can significantly
impact measurement accuracy.
Rs is the shunt calibration resistor value.
U is the ratio of expected signal voltage to excitation voltage with the shunt
calibration circuit engaged. Parameter U appears in the equations for
simulated strain and is defined by the following equation:
–Rg
U = ----------------------4R s + 2R g
ν is the Poisson’s ratio, defined as the negative ratio of transverse strain to
axial strain (longitudinal) strain. Poisson’s ratio is a material property of the
specimen you are measuring.
VCH is the measured voltage of the signal.
VEX is the excitation voltage.
Vr is the voltage ratio that is used in the voltage to strain conversion
equations and is defined by the following equation:
V CH ( strained ) – V CH (unstrained)
V r =  -------------------------------------------------------------------------------


V EX
© National Instruments Corporation
4-3
SCXI-1520 User Manual
Chapter 4
Theory of Operation
Software Scaling and Equations
After you have acquired the voltage signal VCH , you can scale this voltage
to the appropriate strain units in software. This is done automatically for
you in NI-DAQmx using a strain task or strain channel and in Traditional
NI-DAQ (Legacy) using the strain virtual channel. You also can scale
the voltages manually in your application using the voltage-to-strain
conversion equations provided in this document for each
configuration type.
Finally, there are voltage-to-strain conversion functions included in
LabVIEW, NI-DAQmx, and Traditional NI-DAQ (Legacy). In LabVIEW,
the conversion function, Convert Strain Gauge Reading VI, is in the Data
Acquisition»Signal Conditioning subpalette. The prototypes for the
NI-DAQ functions, Strain_Convert and Strain_Buf_Convert, are in
the header file convert.h for C/C++, and convert.bas for Visual Basic.
Refer to the Traditional NI-DAQ User Manual and the LabVIEW
Measurements Manual for more information.
The names given the strain-gauge types in these sections directly
correspond to bridge selections in MAX and the LabVIEW Convert Strain
Gauge Reading VI.
Quarter-Bridge Type I
This section provides information for the quarter-bridge strain-gauge
configuration type I. The quarter-bridge type I measures either axial or
bending strain. Figure 4-2 shows how to position a strain-gauge resistor in
an axial and bending configurations. Figure 4-3 shows the quarter-bridge
type I circuit wiring diagram.
R 4 (+ )
Axial
R 4 (+ )
Bending
Figure 4-2. Quarter-Bridge Type I Measuring Axial and Bending Strain
SCXI-1520 User Manual
4-4
ni.com
Chapter 4
Theory of Operation
A quarter-bridge type I has the following characteristics:
Note
•
A single active strain-gauge element is mounted in the principle
direction of axial or bending strain.
•
A passive quarter-bridge completion resistor (dummy resistor) is
required in addition to half-bridge completion.
•
Temperature variation in specimen decreases the accuracy of the
measurements.
•
Sensitivity at 1000 με is ∼ 0.5 mVout /VEX input.
S– is left unwired.
RL
VEX
+
R1
–
–
VCH
R2
RL
+
R3
R4 (+ )
RL
Figure 4-3. Quarter-Bridge I Circuit Diagram
The following symbols apply to the circuit diagram and equations:
•
R1 and R2 are half-bridge completion resistors.
•
R3 is the quarter-bridge completion resistor (dummy resistor).
•
R4 is the active strain-gauge element measuring tensile strain (+ε).
•
VEX is the excitation voltage.
•
RL is the lead resistance.
•
VCH is the measured voltage.
To convert voltage readings to strain units use the following equation:
R
–4 Vr
×  1 + ------L- 
strain ( ε ) = ------------------------------
GF ( 1 + 2V r )
Rg 
where
Rg is the nominal gauge resistance of the sensor.
RL is the lead resistance.
GF is the Gauge Factor.
© National Instruments Corporation
4-5
SCXI-1520 User Manual
Chapter 4
Theory of Operation
To simulate the effect on strain of applying a shunt resistor across R3,
use the following equation:
– 4U
ε s = -----------------------------GF ( 1 + 4U )
Notes The value of the quarter-bridge completion resistor (dummy resistor) must equal
the nominal resistance of the strain gauge. NI recommends using a 0.1% precision resistor.
To minimize temperature drift errors, the strain gauge must have a
self-temperature-compensation (STC) number that corresponds to the thermal expansion
coefficient of the material under test. STC gauges have a temperature sensitivity that
counteracts the thermal expansion coefficient of the test specimen. The STC number
approximately equals the thermally induced change in strain with change in temperature
and is expressed in units of microstrain per degree Fahrenheit. For example, if the test
specimen is aluminum, use a gauge with an STC number of 13.0. If the test specimen is
steel, use a gauge with an STC number of 6.0.
To minimize temperature drift errors in the wiring, use the three-wire connection shown in
Figure 4-3. The wires connected to terminals S+ and QTR carry the same current and are
on opposite sides of the same element of the bridge. Therefore, any temperature-related
changes in voltage drop across RL caused by temperature variation of the leads cancel out,
leaving VCH unchanged. The voltage drop across the lead resistance on a quarter-bridge
type I configuration is uncompensated in hardware. It is important to accurately determine
the gauge lead resistance and enter it in MAX or in the application software equation so
the software can compensate for the voltage drop.
You can neglect lead resistance (RL ) of the wiring if shunt calibration is performed or if
lead length is very short (∼ <10 ft), depending on the wire gauge. For example 10 ft of
24-AWG copper wire has a lead resistance of 0.25 Ω.
Quarter-Bridge Type II
This section provides information for the quarter-bridge strain-gauge
configuration type II. The quarter-bridge type II measures either axial or
bending strain. Figure 4-4 shows how to position a strain-gauge resistor in
an axial and bending configurations. Figure 4-5 shows the quarter-bridge
type II circuit wiring diagram.
SCXI-1520 User Manual
4-6
ni.com
Chapter 4
R4 (+ )
Theory of Operation
R4 (+ )
Axial
Bending
R3
R3
Figure 4-4. Quarter-Bridge Type II Measuring Axial and Bending Strain
A quarter-bridge type II has the following characteristics:
Note
•
One active strain-gauge element and one passive, temperature-sensing
quarter-bridge element (dummy gauge). The active element is
mounted in the direction of axial or bending strain. The dummy gauge
is mounted in close thermal contact with the strain specimen but not
bonded to the specimen, and is usually mounted transverse
(perpendicular) to the principle axis of strain.
•
This configuration is often confused with the half-bridge type I
configuration, with the difference being that in the half-bridge type I
configuration the R3 element is active and bonded to the strain
specimen to measure the effect of Poisson’s ratio.
•
Completion resistors provide half-bridge completion.
•
Compensates for temperature.
•
Sensitivity at 1000 με is ∼ 0.5 mVout /VEX input.
S– and QTR are left unwired.
RL
VEX
+
–
R1
–
R2
VCH
+
RL
RL
R4 (+ )
R3
Figure 4-5. Quarter-Bridge II Circuit Diagram
© National Instruments Corporation
4-7
SCXI-1520 User Manual
Chapter 4
Theory of Operation
The following symbols apply to the circuit diagram and equations:
•
R1 and R2 are half-bridge completion resistors.
•
R3 is the quarter-bridge temperature-sensing element (dummy gauge).
•
R4 is the active strain-gauge element measuring tensile strain (+ε).
•
VEX is the excitation voltage.
•
RL is the lead resistance.
•
VCH is the measured voltage.
To convert voltage readings to strain units use the following equation:
–4 Vr
R
×  1 + ------L-
strain ( ε ) = ------------------------------GF ( 1 + 2V r ) 
Rg
where
Rg is the nominal gauge resistance.
RL is the lead resistance.
GF is the Gauge Factor.
To simulate the effect on strain of applying a shunt resistor across R3,
use the following equation:
– 4U
ε s = -----------------------------GF ( 1 + 4U )
Notes The dummy gauge element must always be unstrained and mounted to the same
type of material as the active gauge, but not strained. The dummy gauge temperature must
closely track the temperature of the active gauge.
Gauges need not have a STC number corresponding to the material type of the test
specimen.
As shown in Figure 4-5, for greatest calibration accuracy, use separate wires between the
bridge and the SCA terminals. Do not directly connect S+ or P– to the SCA terminals
inside the SCXI-1314 terminal block unless the strain-gauge cable length is very short.
You can neglect lead resistance (RL ) of the wiring if shunt calibration is performed or if
lead length is very short (∼ <10 ft), depending on the wire gauge. For example, 10 ft of
24-AWG copper wire has a lead resistance of 0.25 Ω.
The nominal value of R3 is equal to Rg.
SCXI-1520 User Manual
4-8
ni.com
Chapter 4
Theory of Operation
Half-Bridge Type I
This section provides information for the half-bridge strain-gauge
configuration type I. The half-bridge type I measures either axial or
bending strain. Figure 4-6 shows how to position strain-gauge resistors
in an axial and bending configurations. Figure 4-7 shows the half-bridge
type I circuit wiring diagram.
R4 (+ )
R4 (+ )
Axial
R3 (–
Bending
R3 (–
)
)
Figure 4-6. Half-Bridge Type I Measuring Axial and Bending Strain
A half-bridge type I has the following characteristics:
Note
•
Two active strain-gauge elements. One is mounted in the direction
of axial strain, the other acts as a Poisson gauge and is mounted
transverse (perpendicular) to the principal axis of strain.
•
Completion resistors provide half-bridge completion.
•
Sensitive to both axial and bending strain.
•
Compensates for temperature.
•
Compensates for the aggregate effect on the principle strain
measurement due to the Poisson’s ratio of the specimen material.
•
Sensitivity at 1000 με is ∼ 0.65 mVout/VEX input.
S– is left unwired.
RL
VEX
R1
+
–
–
R2
VCH
+
RL
R4 (+ )
RL
R3 (–
)
Figure 4-7. Half-Bridge Type I Circuit Diagram
© National Instruments Corporation
4-9
SCXI-1520 User Manual
Chapter 4
Theory of Operation
The following symbols apply to the circuit diagram and equations:
•
R1 and R2 are half-bridge completion resistors.
•
R3 is the active strain-gauge element measuring compression from
Poisson effect (–νε).
•
R4 is the active strain-gauge element measuring tensile strain (+ε).
•
VEX is the excitation voltage.
•
RL is the lead resistance.
•
VCH is the measured voltage.
To convert voltage readings to strain units use the following equation:
– 4V r
R
- ×  1 + -----L-
strain ( ε ) = ------------------------------------------------------------
GF [ ( 1 + v ) – 2V r ( v – 1 ) ]
R g
where
Rg is the nominal gauge resistance.
RL is the lead resistance.
ν is the Poisson’s ratio.
GF is the Gauge Factor.
To simulate the effect on strain of applying a shunt resistor across R3,
use the following equation:
– 4U
ε s = -----------------------------------------------------------GF [ ( 1 + v ) – 2U ( v – 1 ) ]
Notes In half-bridge type I, R4 is mounted along the principal axis of the stress field
and R3 is mounted transverse to the axis of the stress field. Use this configuration in
applications where no stress exists along the axis of the transverse strain gauge.
Strain gauges need not have a particular STC number.
As shown in Figure 4-9, for greatest calibration accuracy, use separate wires between the
bridge and the SCA terminals. Do not directly connect S+ or P– to the SCA terminals
inside the SCXI-1314 terminal block unless the strain-gauge cable length is very short.
You can neglect lead resistance (RL ) of the wiring if shunt calibration is performed or if
lead length is very short (∼ <10 ft), depending on the wire gauge. For example 10 ft of
24-AWG copper wire has a lead resistance of 0.25 Ω.
The nominal values of R3 and R4 equal Rg.
SCXI-1520 User Manual
4-10
ni.com
Chapter 4
Theory of Operation
Half-Bridge Type II
This section provides information for the half-bridge strain-gauge
configuration type II. The half-bridge type II only measures bending strain.
Figure 4-8 shows how to position strain-gauge resistors in an axial
configuration. Figure 4-9 shows the half-bridge type II circuit wiring
diagram.
R4
R4 (+ )
Axial
Bending
R3 (– )
R3
Figure 4-8. Half-Bridge Type II Rejecting Axial and Measuring Bending Strain
A half-bridge type II configuration has the following characteristics:
Note
•
Two active strain-gauge elements. One is mounted in the direction
of bending strain on one side of the strain specimen (top), the other
is mounted in the direction of bending strain on the opposite side
(bottom).
•
Completion resistors provide half-bridge completion.
•
Sensitive to bending strain.
•
Rejects axial strain.
•
Compensates for temperature.
•
Sensitivity at 1000 με is ∼ 1 mVout/VEX input.
S– is left unwired.
RL
VEX
+
–
R1
–
R2
VCH
+
RL
RL
R4 (+ )
R3 (– )
Figure 4-9. Half-Bridge Type II Circuit Diagram
© National Instruments Corporation
4-11
SCXI-1520 User Manual
Chapter 4
Theory of Operation
The following symbols apply to the circuit diagram and equations:
•
R1 and R2 are half-bridge completion resistors.
•
R3 is the active strain-gauge element measuring compressive
strain (–ε).
•
R4 is the active strain-gauge element measuring tensile strain (+ε).
•
VEX is the excitation voltage.
•
RL is the lead resistance.
•
VCH is the measured voltage.
To convert voltage readings to strain units use the following equation:
–2 V
R
strain ( ε ) = ------------r ×  1 + -----L-
GF 
R g
where
Rg is the nominal gauge resistance.
RL is the lead resistance.
GF is the Gauge Factor.
To simulate the effect on strain of applying a shunt resistor across R3,
use the following equation:
– 2U
ε s = ---------GF
Notes Half-bridge type II requires one strain gauge to undergo tensile strain while the
other strain gauge undergoes compressive strain of the same magnitude. This configuration
is often used to measure bending strain where the strain gauges are mounted on opposite
sides of a beam.
The strain gauges need not have a particular STC number.
As shown in Figure 4-7, for greatest calibration accuracy, use separate wires between the
bridge and the SCA terminals. Do not directly connect S+ or P– to the SCA terminals
inside the SCXI-1314 terminal block unless the strain-gauge cable length is very short.
You can neglect lead resistance (RL ) of the wiring if shunt calibration is performed or if
lead length is very short (∼ <10 ft), depending on the wire gauge. For example 10 ft of
24-AWG copper wire has a lead resistance of 0.25 Ω.
The nominal values of R3 and R4 equal Rg.
SCXI-1520 User Manual
4-12
ni.com
Chapter 4
Theory of Operation
Full-Bridge Type I
This section provides information for the full-bridge strain-gauge
configuration type I. The full-bridge type I only measures bending strain.
Figure 4-10 shows how to position strain-gauge resistors in a bending
configuration. Figure 4-11 shows the full-bridge type I circuit wiring
diagram.
R2
R2 (+ )
R1
R4
R1 (– )
R4 (+ )
R3
R3 (– )
Bending
Axial
Figure 4-10. Full-Bridge Type I Rejecting Axial and Measuring Bending Strain
A full-bridge type I configuration has the following characteristics:
•
Four active strain-gauge elements. Two are mounted in the direction
of bending strain on one side of the strain specimen (top), the other
two are mounted in the direction of bending strain on the opposite side
(bottom).
•
Highly sensitive to bending strain.
•
Rejects axial strain.
•
Compensates for temperature.
•
Compensates for lead resistance.
•
Sensitivity at 1000 με is ∼ 2.0 mVout /VEX input.
R4 (+ )
R1 (– )
VEX
+
–
–
R2 (+ )
VCH
+
R3 (– )
Figure 4-11. Full-Bridge Type I Circuit Diagram
© National Instruments Corporation
4-13
SCXI-1520 User Manual
Chapter 4
Theory of Operation
The following symbols apply to the circuit diagram and equations:
•
R1 is an active strain-gauge element measuring compressive
strain (–ε).
•
R2 is an active strain-gauge element measuring tensile strain (+ε).
•
R3 is an active strain-gauge element measuring compressive
strain (–ε).
•
R4 is an active strain-gauge element measuring tensile strain (+ε).
•
VEX is the excitation voltage.
•
RL is the lead resistance.
•
VCH is the measured voltage.
To convert voltage readings to strain units use the following equation:
–V
strain ( ε ) = --------r
GF
where
GF is the Gauge Factor.
To simulate the effect on strain of applying a shunt resistor across R3,
use the following equation:
–U
ε s = -------GF
Notes Strain gauges need not have a particular STC number.
As shown in Figure 4-11, for greatest calibration accuracy, use separate wires between the
bridge and the SCA terminals. Do not directly connect S+ or P– to the SCA terminals
inside the SCXI-1314 terminal block unless the strain-gauge cable length is very short.
The nominal values of R1, R2, R3, and R4 equal Rg.
Full-Bridge Type II
This section provides information for the full-bridge type II strain-gauge
configuration. The full-bridge type II only measures bending strain.
Figure 4-12 shows how to position strain-gauge resistors in a bending
configuration. Figure 4-13 shows the full-bridge type II circuit wiring
diagram.
SCXI-1520 User Manual
4-14
ni.com
Chapter 4
R4
Theory of Operation
R4 (+ )
R1
R1 (–
)
R3 (– )
R3
R2 (+
Axial
R2
Bending
)
Figure 4-12. Full-Bridge Type II Rejecting Axial and Measuring Bending Strain
A full-bridge type II configuration has the following characteristics:
•
Four active strain-gauge elements. Two are mounted in the direction of
bending strain with one on one side of the strain specimen (top) and the
other on the opposite side (bottom). The other two act together as a
Poisson gauge and are mounted transverse (perpendicular) to the
principal axis of strain with one on one side of the strain specimen
(top) and the other on the opposite side (bottom).
•
Rejects axial strain.
•
Compensates for temperature.
•
Compensates for the aggregate effect on the principle strain
measurement due to the Poisson’s ratio of the specimen material.
•
Compensates for lead resistance.
•
Sensitivity at 1000 με is ∼ 1.3 mVout /VEX input.
R1(– )
VEX
+
R4 (+ )
–
–
R2(+ )
VCH
+
R3 (– )
Figure 4-13. Full-Bridge Type II Circuit Diagram
The following symbols apply to the circuit diagram and equations:
•
R1 is an active strain-gauge element measuring compressive Poisson
effect (–νε).
•
R2 is an active strain-gauge element measuring tensile Poisson
effect (+νε).
© National Instruments Corporation
4-15
SCXI-1520 User Manual
Chapter 4
Theory of Operation
•
R3 is an active strain-gauge element measuring compressive
strain (–ε).
•
R4 is an active strain-gauge element measuring tensile strain (+ε).
•
VEX is the excitation voltage.
•
RL is the lead resistance.
•
VCH is the measured voltage.
To convert voltage readings to strain units use the following equation:
–2 Vr
strain ( ε ) = -----------------------GF ( 1 + v )
where
GF is the Gauge Factor.
ν is the Poisson’s ratio.
To simulate the effect on strain of applying a shunt resistor across R3,
use the following equation:
– 2U ε s = -----------------------GF ( 1 + v )
Notes Full-bridge type II is sometimes used for strain measurement of bending beams.
R3 and R4 are positioned along the beam axis and on opposite sides of the beam, and
R1 and R2 are positioned transverse to the beam axis and on opposite sides of the beam.
Strain gauges need not have a particular STC number.
As shown in Figure 4-13, for greatest calibration accuracy, use separate wires between the
bridge and the SCA terminals. Do not directly connect S+ or P– to the SCA terminals
inside the SCXI-1314 terminal block unless the strain-gauge cable length is very short.
The nominal values of R1, R2, R3, and R4 equal Rg.
Full-Bridge Type III
This section provides information for the full-bridge strain-gauge
configuration type III. The full-bridge type III only measures axial strain.
Figure 4-14 shows how to position strain-gauge resistors in an axial
configuration. Figure 4-15 shows the full-bridge type III circuit wiring
diagram.
SCXI-1520 User Manual
4-16
ni.com
Chapter 4
Theory of Operation
R2
R2 (+ )
R1 (–
R1
)
R4 (+ )
R4
R3 (–
Bending
Axial
)
R3
Figure 4-14. Full-Bridge Type III Measuring Axial and Rejecting Bending Strain
A full-bridge type III configuration has the following characteristics:
•
Four active strain-gauge elements. Two are mounted in the direction of
axial strain with one on one side of the strain specimen (top), the other
on the opposite side (bottom). The other two act together as a Poisson
gauge and are mounted transverse (perpendicular) to the principal axis
of strain with one on one side of the strain specimen (top) and the other
on the opposite side (bottom).
•
Compensates for temperature.
•
Rejects bending strain.
•
Compensates for the aggregate effect on the principle strain
measurement due to the Poisson’s ratio of the specimen material.
•
Compensates for lead resistance.
•
Sensitivity at 1000 με is ∼ 1.3 mVout /VEX input.
R1(– )
VEX
+
R4 (+ )
–
–
R2 (+ )
VCH
+
R3 (–
)
Figure 4-15. Full-Bridge Type III Circuit Diagram
The following symbols apply to the circuit diagram and equations:
•
R1 is an active strain-gauge element measuring compressive Poisson
effect (–νε).
•
R2 is an active strain-gauge element measuring tensile strain (+ε).
© National Instruments Corporation
4-17
SCXI-1520 User Manual
Chapter 4
Theory of Operation
•
R3 is an active strain-gauge element measuring compressive Poisson
effect (–νε).
•
R4 is an active strain-gauge element measuring the tensile strain (+ε).
•
VEX is the excitation voltage.
•
RL is the lead resistance.
•
VCH is the measured voltage.
To convert voltage readings to strain units use the following equation:
–2 Vr
strain ( ε ) = ---------------------------------------------------------GF [ ( v + 1 ) – V r ( v – 1 ) ]
where
GF is the Gauge Factor.
ν is the Poisson’s ratio.
To simulate the effect on strain of applying a shunt resistor across R3,
use the following equation:
– 4U
ε s = --------------------------------------------------------GF [ ( v + 1 ) – U ( v – 1 ) ]
Notes Full-bridge type III is sometimes used for axial strain measurement. R2 and R4
are positioned along the beam axis and on opposite sides of the beam, and R1 and R3 are
positioned transverse to the beam axis and on opposite sides of the beam.
Strain gauges need not have a particular STC number.
As shown in Figure 4-15, for greatest calibration accuracy, use separate wires between the
bridge and the SCA terminals. Do not directly connect S+ or P– to the SCA terminals
inside the SCXI-1314 terminal block unless the strain-gauge cable length is very short.
The nominal values of R1, R2, R3, and R4 equal Rg.
SCXI-1520 Theory of Operation
This section includes a brief overview and a detailed discussion of the
circuit features of the module. Refer to Figure 4-16 while reading this
section.
SCXI-1520 User Manual
4-18
ni.com
© National Instruments Corporation
4-19
S7+
S1+
SCB0
SCB0
SCA0
SCA0
RS0–
P0–
QTR
Screw
Terminals
to Field
Wiring
Shunt Cal B
Shunt Cal A
Quarter-Bridge
Completion
+
–
–
+
B
–X1
Null
Compensation
Fine
Signal Conditioning (see above)
Lowpass
Filter
Track and
Hold, X1
Calibration
Source
RS–
RS+
SCXI-1520 Module
Excitation
Voltage
Setting
Variable Gain
X1 to X50
Null
Compensation
Coarse
Lowpass
Filter
Signal Conditioning (see above)
Shunt Calibration Switches
A
Output
Amp
HalfBridge
Completion
Output
Amp
Inst. Amp.
X1 or X20
Signal Conditioning
Analog
Multiplexer
Multiplexer
Control
S7+
S1+
To
Analog
Bus
Digital Interface
and Control
Analog
Bus
Switch
Scan Clock
CH7–
CH7+
CH0–
CH0+
CH1+
Buffer
RS0–
S0+
RS0+
Rear Signal Connector
P0+
RS0+
S0–
S0+
SCXI-1314
Terminal
Block
Chapter 4
Theory of Operation
SCXIbus Connector
Figure 4-16. Block Diagram of SCXI-1314/SCXI-1520 Combination
SCXI-1520 User Manual
Chapter 4
Theory of Operation
The analog input signal from the strain gauge or bridge sensor connects to
SX+ and SX– of the terminal block. The signal passes through the terminal
block to an electronic four-position switch in the module. Figure 4-16
shows the switching stage that controls the input of to the signal
conditioning circuitry and the E/M Series DAQ device.
In the switching stage there are four positions. In the first position where
SX+ and SX– inputs connect directly to an instrumentation amplifier. This
position is for full-bridge connections or general-purpose analog input. The
second position connects the negative input to the internal voltage divider
between the excitation terminals. The internal voltage divider functions as
bridge completion for quarter- and half-bridge configurations. The third
switch position connects the amplifier input to a calibration voltage source
inside the module for gain calibration, and the fourth position grounds both
inputs for offset calibration.
The instrumentation amplifier stage presents a very high input impedance
to external signals and passes only the differential signal. The offset null
compensation circuitry adjusts the signal voltage by a specified offset after
an offset null calibration is performed.
The signal from the instrumentation amplifier stage passes through a
lowpass filter stage, a variable gain stage, another lowpass filter stage, and
finally a simultaneous sample-and-hold stage before reaching the output
multiplexer for multiplex mode operation. The signals S1± through S7± are
also directly routed to the rear signal connector for parallel mode operation.
You can set the cutoff frequencies of the lowpass filter stage to one of
five settings.You also can bypass the filters for a maximum bandwidth of
20 kHz.
The variable gain stage allows you to set the gain at many discrete settings
between 1 and 50. These settings, along with the 1 or 20 setting of the
instrumentation amplifier, permit the SCXI-1520 to have 49 gain settings
between 1 and 1000.
The simultaneous sample-and-hold stage uses track-and-hold circuitry
to perform simultaneous sampling for all channels. When enabled,
track-and-hold circuitry holds the signal at the beginning of a scan, and
reverts back to track mode at the end of a scan.
The signal then passes from the simultaneous sample-and-hold stage to
the multiplexer stage. The modes of operation are determined by the
multiplexer stage. If configured for multiplexed mode operation, the
multiplexer selects the conditioned analog signal from one of the
SCXI-1520 User Manual
4-20
ni.com
Chapter 4
Theory of Operation
eight channels for routing. The signal is routed to the E/M Series DAQ
device channel 0 if the SCXI-1520 is the cabled module and/or to the SCXI
backplane through the SCXIbus connector. If configured for parallel mode
operation, the signals are routed through the rear signal connector to the
digitizing DAQ device.
The multiplexer stage is controlled by the digital interface and control
circuitry. The digital interface and control circuitry stores the scan list,
controls the multiplexer, and allows flexible scanning (random scanning).
Two other circuitry stages that are not directly in the signal path are
excitation circuitry and shunt calibration switches. The excitation stage is
stable output with a controlled feedback loop called remote sense. The
remote sense signal is connected to the analog multiplexer. You can scan
remote sense when configured in multiplexed mode operation.
The shunt calibration switches are controlled by the digital interface and
control circuity. You must connect the SCX terminals to the bridge for shunt
calibration to function correctly. When the switch is closed, a socketed
shunt calibration resistor in the SCXI-1314 connects across a leg of a
Wheatstone bridge.
For more detailed information about the operation of any of these circuitry
stages, refer to the Bridge Configuration and Completion section, the
Excitation section, the Gain section, the Filter Bandwidth and Cutoff
Frequency section, the Offset Null Compensation section, the Shunt
Calibration section, the Simultaneous Sample and Hold section, and the
Modes of Operation section.
Bridge Configuration and Completion
You can configure the SCXI-1520 for use with Wheatstone bridge sensors
that require bridge completion. Bridge completion is necessary for quarteror half-bridge sensors. You can set the SCXI-1520 for quarter-, half-,
or full-bridge configuration to match the configuration completion
requirements of each sensor. When quarter- or half-bridge configuration is
selected, Terminal SX– (where X is a particular channel) is disconnected
from the front signal connector and internally connected to a half-bridge
completion network. When quarter-bridge configuration is selected,
a socketed quarter-bridge completion resistor in the terminal block is
internally connected between PX– and the QTR terminal. You then field
wire the quarter-bridge sensor between PX+ and QTR. Make sure that the
value of the precision quarter-bridge completion resistor matches the
nominal gauge resistance of the quarter-bridge sensor. The quarter-bridge
completion resistor is socketed for easy replacement.
© National Instruments Corporation
4-21
SCXI-1520 User Manual
Chapter 4
Theory of Operation
When using the SCXI-1520 and SCXI-1314 configured for quarter-bridge
completion, do not wire the sensor or any signal to SX–.
Note
Refer to the Configurable Settings in MAX section of Chapter 3,
Configuring and Testing, for more information about programmatically
setting bridge completion in MAX. For more information about
programmatically setting bridge completion in NI-DAQmx and Traditional
NI-DAQ (Legacy), refer to the Developing Your Application in NI-DAQmx
section or the Developing Your Application in Traditional NI-DAQ
(Legacy) section, respectively, of Chapter 5, Using the SCXI-1520.
Excitation
The SCXI-1520 provides DC excitation voltage for a Wheatstone bridge
sensor. For half- and full-bridge applications, the excitation voltage is
available at terminal block connections PX+ and PX–. For quarter-bridge
applications, PX– is not used; instead, wire to terminals PX+ and QTRX.
Terminal QTRX internally connects to PX–.
Excitation voltage originates from two output buffers dedicated to each
channel. Since each channel is controlled independently, a short circuit
across the excitation terminals of one channel has no effect on the
excitation of another channel. The output buffers have negative feedback
connections at the terminal block remote-sense terminals, RSX+ and RSX–.
You can run separate wires from the bridge to these terminals so that the
amplifiers obtain feedback directly from the bridge, thereby forcing bridge
voltage to equal the desired setting.
Excitation voltage originates from two excitation output buffers per
channel. One output buffer generates the positive excitation voltage, and
the other output buffer generates the negative excitation voltage. Since each
channel is controlled independently, a short circuit across the excitation
terminals of one channel has no effect on the excitation of another channel.
PX+ is always positive with respect to ground, and PX– is always negative
with respect to ground. The inverting amplifier –X1 forces the voltage at
PX– to equal the negative of the voltage at PX+. For example, if you set the
module output for +5 V, PX+ is at +2.5 V with respect to ground, and PX–
is at –2.5 V with respect to ground. The excitation setting originates from
an internal digital-to-analog converter (DAC). You can set the excitation
voltage in a near-continuous range using NI-DAQmx and between 0 V and
10 V in 0.625 V increments using Traditional NI-DAQ (Legacy). You can
power a 350 Ω full-bridge at 10 V without exceeding the maximum power
rating of the excitation source. The excitation outputs are protected with
SCXI-1520 User Manual
4-22
ni.com
Chapter 4
Theory of Operation
surge suppressors that prevent either excitation output terminal from
exceeding 6 V with respect to chassis ground.
Chassis ground is at the same potential as earth ground when the chassis is plugged
into a standard 3-prong AC outlet. If PX– is connected to earth ground, the excitation
source does not function properly.
Note
Refer to the Configurable Settings in MAX section of Chapter 3,
Configuring and Testing, for more information about programmatically
setting the excitation level in MAX. For more information about
programmatically setting the excitation level in NI-DAQmx and Traditional
NI-DAQ (Legacy), refer to the Developing Your Application in NI-DAQmx
section or the Developing Your Application in Traditional NI-DAQ
(Legacy) section, respectively, of Chapter 5, Using the SCXI-1520.
Remote Sense
The excitation output buffers have negative feedback connections at the
terminal block remote-sense terminals, RSX+ and RSX–. You can run
separate wires from the bridge to these terminals so that the amplifiers
obtain feedback directly from the bridge, forcing bridge voltage to exactly
equal the desired setting. This removes unwanted DC offset in the signal
and compensates for changes in lead resistance caused by temperature
variation in the lead wires.
The SCXI-1520 excitation output circuits set the output voltage by
monitoring the remote-sense terminals. Therefore, the SCXI-1520 corrects
for a voltage (I × R) drop in the excitation leads between the module and
the bridge, even if lead resistance changes with temperature.
You can scan the remote sense terminals. The output multiplexer has input
connections to the RSX+ and RSX– terminals. You can scan these terminals
for monitoring and scaling purposes, even if the remote-sense terminals are
not connected. Refer to Chapter 5, Using the SCXI-1520, and Appendix B,
Using SCXI Channel Strings with Traditional NI-DAQ (Legacy) 7.0
or Later, for more information.
Wire the SCXI-1520 for remote sense as shown in Figure 2-8,
Remote-Sense Circuit Diagram. There are no configuration settings you
need to change in the software.
Note If you use remote sense, set RL to zero in the MAX configuration of the channel and
in your application equations for measured strain (ε).
© National Instruments Corporation
4-23
SCXI-1520 User Manual
Chapter 4
Theory of Operation
If you leave the remote-sense terminal unconnected, internal 1 kΩ resistors
provide feedback to the buffers from the PX+ and PX– terminals. Therefore,
you need not install a jumper wire between RSX+ and PX+, or RSX– and
PX–. However, NI recommends performing a shunt calibration to
compensate for the voltage drop across lead resistance.
NI recommends that you connect remote sense wires to the sensor directly for
optimal performance.
Note
If you are not connecting remote sense and not performing shunt
calibration, you must scale the measurements to compensate for the
excitation voltage drop across the lead resistance. You should use the
following gain adjustment factor:
2R
Gain Adjusting Factor = 1 + --------LRg
This gain adjust factor is used in your application to compensate for the
voltage drop across the leads as follows:
V meas × Gain Adjusting Factor
Gain
The SCXI-1520 has multiple gain stages to provide optimal overall signal
gains appropriate for fully utilizing the range of the digitizing E/M Series
DAQ device. The first gain stage (the instrumentation amplifier stage)
provides gains of either 1 or 20. The second gain stage provides many
discrete settings between 1 and 50. Together these two gain stages combine
for 49 overall gain settings with overall gains between 1 and 1000.
For overall module gain settings equal to or greater than 20, the gain of the
first stage is set to 20 so that the noise and offset drift of later stages is small
in comparison to this stage. The instrumentation amplifier stage uses
operational amplifiers with very low temperature drift and noise
characteristics. If overall module gain is less than 20, the first stage
is set to 1 and the appropriate second stage gain is applied.
In normal operation of the SCXI-1520, you need not set the gain since
NI-DAQ sets the gain based on the range of your virtual channel, task,
or global channel, or the input limits set in LabVIEW.
In NI-DAQmx the default setting is 1.0 and in Traditional NI-DAQ
(Legacy) the default gain setting is 100.00.
SCXI-1520 User Manual
4-24
ni.com
Chapter 4
Theory of Operation
Refer to the Configurable Settings in MAX section of Chapter 3,
Configuring and Testing, for more information about programmatically
setting gain using range settings in MAX. For more information about
programmatically setting gain using range settings in NI-DAQmx and
Traditional NI-DAQ (Legacy), refer to the Developing Your Application in
NI-DAQmx section or the Developing Your Application in Traditional
NI-DAQ (Legacy) section, respectively, of Chapter 5, Using the
SCXI-1520.
Filter Bandwidth and Cutoff Frequency
The SCXI-1520 provides two filtering stages with an overall response of a
four-pole Butterworth filter. You can control the cutoff frequency of the
filter through software. You can choose 10 Hz, 100 Hz, 1 kHz, 10 kHz, or
filter-bypass mode. For additional flexibility in cutoff frequency settings
and for greater suppression, NI recommends combining the hardware
filtering provided by the SCXI-1520 with digital filtering. NI recommends
using the Advanced Analysis functions of LabVIEW, LabWindows/CVI,
or Measurement Studio. By combining hardware anti-aliasing with digital
filtering, you can choose any cutoff frequency.
The Advanced Analysis functions are only available in LabVIEW Full or
Professional Development Systems, and LabWindows/CVI Base or Full
Development Systems.
Refer to the Configurable Settings in MAX section of Chapter 3,
Configuring and Testing, for more information about programmatically
setting the cutoff frequency of the filter in MAX. For more information
about programmatically setting the cutoff frequency of the filter in
NI-DAQmx and Traditional NI-DAQ (Legacy), refer to the Developing
Your Application in NI-DAQmx section or the Developing Your
Application in Traditional NI-DAQ (Legacy) section, respectively, of
Chapter 5, Using the SCXI-1520.
Offset Null Compensation
The SCXI-1520 provides offset null compensation to adjust signal voltages
to proper levels when the strain gauge or bridge sensor is at rest
(unstrained). For most sensors offset null compensation is used to remove
an initial voltage offset from the Wheatstone bridge. Many strain-gauge
signal conditioning devices use a manually adjusted multi-turn screw
potentiometer for offset null compensation. In the SCXI-1520, offset null
compensation is performed electronically using software-controlled
electronic potentiometers.
© National Instruments Corporation
4-25
SCXI-1520 User Manual
Chapter 4
Theory of Operation
Two offset null potentiometers are used, one for coarse adjustments and the
other for fine adjustments. The sum of the two potentiometer signals is
added to the analog input path to adjust the signal voltage to remove the
offset, which nulls the strain-gauge channel. The voltage input to the
potentiometers is a voltage proportional to the excitation voltage setting.
Therefore, if the excitation voltage changes by a small amount due to
changes such as temperature and sensor loading, the correction signal
produced by the offset null potentiometers changes by the same amount and
the offset null is maintained.
The offset null potentiometers are controlled digitally using control codes.
The control codes of the offset null potentiometers are set in software using
integer values. The coarse potentiometer ranges from 0 to 127 and the fine
potentiometer from 0 to 4095. The span of correction (the voltage nulling
range) for each potentiometer depends on the channel gain setting.
Table 4-2 summarizes the nulling range and scale of the control codes.
Table 4-2. Control Codes for Coarse and Fine Offset Null Potentiometers
Offset Null
Potentiometer
Coarse
Fine
Approximate
Correction
Span at Analog
Input
Range
(Integer Values)
Mid-Scale
Module
Channel Gain
Settings
0 to 127
62
≥20
VEX /10
<20
2 × VEX
≥20
VEX /364
<20
VEX /18
0 to 4095
2047
In most cases, you do not explicitly set the offset null potentiometers, but
instead allow the NI-DAQ driver software to automatically adjust them for
you. You can do this either through MAX or in your application.
Refer to the Configurable Settings in MAX section of Chapter 3,
Configuring and Testing, for more information about programmatically
performing offset null compensation in MAX. For more information about
programmatically performing offset null compensation in NI-DAQmx and
Traditional NI-DAQ (Legacy), refer to the Developing Your Application in
NI-DAQmx section or the Developing Your Application in Traditional
NI-DAQ (Legacy) section, respectively, of Chapter 5, Using the
SCXI-1520.
SCXI-1520 User Manual
4-26
ni.com
Chapter 4
Theory of Operation
Shunt Calibration
Shunt calibration is a process used to obtain a gain adjust factor, which is
used to correct for system gain error and discrepancies between nominal
Gauge Factor and actual Gauge Factor of the strain gauge.
The gain adjust factor is derived using theoretical (simulated) signal levels
that should result from engaging a shunt resistor across one leg of a bridge
sensor and the measured signal levels with the shunt resistor actually
engaged.
Use the following formula to calculate the gain adjust factor:
simulated signal level
gain adjust factor = ----------------------------------------------------------------------------------------------------------------------measured signal level with shunt resistor engaged
The gain adjust factor is then multiplied by each future measurement
to obtain highly accurate measurements that are adjusted for any gain
errors or any discrepancies in the nominal Gauge Factor. Refer to the
Configurable Settings in MAX section of Chapter 3, Configuring and
Testing, for more information about performing shunt calibration
automatically in global channels using NI-DAQmx in MAX or strain
virtual channels using Traditional NI-DAQ (Legacy) and tasks. For more
information about programmatically performing shunt calibration switches
in NI-DAQmx and Traditional NI-DAQ (Legacy), refer to the Developing
Your Application in NI-DAQmx section or the Developing Your
Application in Traditional NI-DAQ (Legacy) section, respectively,
of Chapter 5, Using the SCXI-1520.
The SCXI-1520 has two independent shunt calibration circuits available for
each channel at terminal sets SCAX and SCBX on the terminal block. Each
shunt calibration circuit consists of a resistor in series with a switch. The
SCXI-1520 shunt calibration switch is a long-life solid-state switch. The
electronic switch is galvanically isolated from ground; therefore, you can
connect the switch across any external bridge element.
© National Instruments Corporation
4-27
SCXI-1520 User Manual
Chapter 4
Theory of Operation
Notes You can control an individual shunt calibration switch or combination of multiple
shunt calibration switches using NI-DAQ software. The shunt calibration resistors in series
with each switch are housed in the SCXI-1314 terminal block. The shunt calibration
resistors are socketed for easy replacement. The resistors are RN-55 style (standard 1/4 W)
precision resistors. For resistor replacement instructions, refer to the SCXI-1314 Universal
Strain Terminal Block Installation Guide.
Perform an offset null compensation just before you perform a shunt calibration.
Performing a shunt calibration before an offset null compensation causes improper gain
adjustment because the offset signal voltage is compensated multiple times.
Simultaneous Sample and Hold
Simultaneous sample and hold (SS/H) signal conditioning allows
multiplexing MIO DAQ devices to return synchronized samples of all
channels with negligible skew time between channels. SS/H signal
conditioning is performed on the SCXI-1520 with track-and-hold (T/H)
circuitry. The outputs of the T/H amplifiers follow their inputs, also called
tracking the inputs, until they receive a hold signal from the DAQ device.
All channels with T/H circuitry hold their signal at the same time, even
if they are on different SCXI modules. The DAQ device then digitizes
the signal of each channel, giving you simultaneous sampling between
channels since no time elapsed between the holding of each signal. All
signals are then released and the T/H circuitry output returns to tracking the
input signal. For accurate measurements, you can use the SS/H equations
to calculate the maximum sample rate when scanning SCXI systems with
at least one SS/H module in the scan list. Figure 4-17 shows and example
of a signal during a SS/H sampling.
SCXI-1520 User Manual
4-28
ni.com
Chapter 4
Theory of Operation
Volts
CH 0
CH 1
CH 2
Time
Hold
Line
Convert
1
2
3
1 HoldTime
2 Max (Min Settle Time of MIO, Min Settle Time of SCXI)
3 TrackTime
Figure 4-17. Signal During Simultaneous Sample-and-Hold Sampling
It is possible to enable and disable SS/H programmatically in NI-DAQmx,
although NI recommends that you leave SS/H enabled for most
applications. Disabling SS/H for one module disables this feature for all
modules in all chassis that are controlled by the same DAQ device. You
should only disable SS/H if your application does not require simultaneous
sampling and requires higher acquisition rates than are possible with SS/H
enabled. Refer to the Developing Your Application in NI-DAQmx section
of Chapter 5, Using the SCXI-1520, for more information about
© National Instruments Corporation
4-29
SCXI-1520 User Manual
Chapter 4
Theory of Operation
programmatically enabling and disabling SS/H using NI-DAQmx in your
application.
Maximum Simultaneous Sample and Hold Sample
Rate Using NI-DAQmx
When using NI-DAQmx you can use the SCXI-1520 in multiplexed or
parallel mode.
Multiplexed Mode
Use the following formula to calculate the maximum SS/H sample rate in
multiplexed mode:
1
SR = -------------------------------------------------------------------------------------------------------------------------------------------------------------------------------(HT + (NoC – 1) × [Maximum of either (MST MIO ) or (MST SCXI )] + TT)
where
SR is sample rate—frequency of acquisition of all channels
HT is hold time—the time between holding all the SS/H channels and
the first A/D conversion
NoC is number of channels—the total number of channels being
sampled in the scan list (SS/H or not)
MSTMIO is minimum settle time of MIO—inverse of maximum sample
rate of the MIO (also minimum interchannel delay)
MSTSCXI is minimum settle time of SCXI—inverse of maximum
multiplex rate of SCXI (1 ÷ 333 k = 3 μs for 12-bit MIO, 1 ÷ 1000 k =
10 μs for 16-bit MIO)
TT is track time—the minimum time between the last AD conversion
of the current scan and engaging the hold signal of SS/H channels of
next scan
Table 4-3 shows some example values used to determine the SR using the
general equation.
SCXI-1520 User Manual
4-30
ni.com
Chapter 4
Theory of Operation
Table 4-3. NI-DAQmx Values Used to Determine Maximum Sample Rate in Multiplexed Mode
MIO
Device
Device
Accuracy
(Bits)
Device
Max
Sample
Rate (S/s)
NI 6070E
12
1250000
NI 6023E
12
NI 6221
(68-Pin)
16
NI 6289
18
200000
3
7
32258
32258
0.8
3
7
9709
9709
8
5
3
7
22222
22222
32
5
3
7
6061
6061
8
4
3
7
26316
5181
32
4
3
7
7463
1486
8
1.6
3
7
32258
5181
32
1.6
3
7
9709
1486
NoC
MSTMIO
(μs)
MSTSCXI
(μs)†
3
8
0.8
32
3
625000
DAQmx SR
Required for
Maximum
Accuracy
(Hz)‡
HT
(μs)
3
250000
TT
(μs)†
Default
NI-DAQmx SR
(Multiplexed)
(Hz)
3
†
These are the default values used by DAQmx, but these might not be the desired values for your application.
‡
For DAQ boards with a 16 bit or higher ADC, 20 μs was used for MSTSCXI and 50 μs for TT.
Note: To use a MSTSCXI value that is different than the 3 μs default, you must explicitly set the AI Convert Clock Rate in
DAQmx. Refer to your ADE help file for details on setting the AI Convert Clock Rate property.
Maximum SS/H Sample Rates in Parallel Mode
Use the following formula to calculate the maximum SS/H sample rate in
parallel mode:
1
SR = ---------------------------------------------------------------------------------------(HT + (NoC – 1) × (MST MIO ) + TT)
where
SR is sample rate—frequency of acquisition of all channels
HT is hold time—the time between holding all the SS/H channels and
the first A/D conversion
NoC is number of channels—the total number of channels being
sampled in the scan list (SS/H or not)
MSTMIO is minimum settle time of MIO—inverse of maximum sample
rate of the MIO (also minimum interchannel delay)
TT is track time—the minimum time between the last AD conversion
of the current scan and engaging the hold signal of SS/H channels of
next scan
© National Instruments Corporation
4-31
SCXI-1520 User Manual
Chapter 4
Theory of Operation
Table 4-4 shows some example values used to determine the SR using the
general equation.
Table 4-4. NI-DAQmx Values Used to Determine Maximum Sample Rate in Parallel Mode
TT
(μs)†
Default
NI-DAQmx
SR (Parallel)
(Hz)
DAQmx SR
Required for
Maximum
Accuracy
(Hz)‡
MIO
Device
Device
Accuracy
(Bits)
Device
Max
Sample
Rate (S/s)
NI 6070E
12
1250000
3
8
0.8
7
64103
64103
NI 6023E
12
200000
3
8
5
7
22222
22222
NI 6221
(68-Pin)
16
250000
3
8
4
7
26316
12346
NI 6254
16
1000000
3
8
1
7
58824
16667
3
16
1
7
40000
14706
3
8
1.6
7
47170
15576
3
16
1.6
7
29412
12987
NI 6289
18
625000
HT
(μs)
NoC
MSTMIO
(μs)
†
These are the default values used by DAQmx, but these might not be the desired values for your application.
‡
For DAQ boards with a 16 bit or higher ADC, 20 μs was used for MSTSCXI and 50 μs for TT.
Maximum Simultaneous Sample and Hold Using
Traditional NI-DAQ (Legacy)
When using Traditional NI-DAQ (Legacy), you can only use the
SCXI-1520 in multiplexed mode. To use parallel mode, you must use
NI-DAQmx.
SCXI-1520 User Manual
4-32
ni.com
Chapter 4
Theory of Operation
Multiplexed Mode
Use the following formula to calculate the maximum SS/H sample rate in
multiplexed mode:
1
SR = --------------------------------------------------------------------------------------------------------------------------------------------------------------2
2
NoC × (Maximum of either MST MIO + MST SCXI or HT ) + TT
where
SR is sample rate—frequency of acquisition of all channels
HT is hold time—the time between holding all the SS/H channels and
the first A/D conversion
NoC is number of channels—the total number of channels being
sampled in the scan list (SS/H or not)
MSTMIO is minimum settle time of MIO—inverse of maximum sample
rate of the MIO (also minimum interchannel delay)
MSTSCXI is minimum settle time of SCXI—inverse of maximum
multiplex rate of SCXI (1 ÷ 333 k = 3 μs for 12-bit MIO, 1 ÷ 1000 k =
10 μs for 16-bit MIO)
TT is track time—the minimum time between the last AD conversion
of the current scan and engaging the hold signal of SS/H channels of
next scan
Table 4-5 shows some example values used to determine the SR using the
general equation.
Table 4-5. Traditional NI-DAQ (Legacy) Values Used to Determine Maximum Sample Rate in Multiplexed Mode
MIO
Device
Device
Accuracy
(Bits)
Device Maximum
Sample Rate (S/s)
HT
(µs)
NoC
MSTMIO
(µs)
MSTSCXI
(µs)
TT
(µs)
Maximum SR
Traditional NI-DAQ
(Legacy) Multiplexed
NI 6070E
12
1250000
3
8
1
3
7
30961
NI 6070E
12
1250000
3
32
1
3
7
9243
NI 6023E
12
200000
3
8
5
3
7
18640
NI 6023E
12
200000
3
32
5
3
7
5166
NI 6052E
16
333333
3
8
3
10
7
11047
NI 6052E
16
333333
3
32
3
10
7
2932
NI 6032E
16
100000
3
8
10
10
7
8324
NI 6032E
16
100000
3
32
10
10
7
2176
© National Instruments Corporation
4-33
SCXI-1520 User Manual
Chapter 4
Theory of Operation
Modes of Operation
The SCXI-1520 provides two modes of operation for passing the
conditioned signals to the digitizing DAQ device—multiplexed mode and
parallel mode.
Theory of Multiplexed Mode Operation
In multiplexed mode, all input channels of an SCXI module are
multiplexed into a single analog input channel of the DAQ device.
Multiplexed mode operation is ideal for high channel count systems.
Multiplexed mode is typically used for performing scanning operations
with the SCXI-1520. The power of SCXI multiplexed mode scanning is its
ability to route many input channels to a single channel of the DAQ device.
The multiplexing operation of the analog input signals is performed
entirely by multiplexers in the SCXI modules, not inside the DAQ device
or SCXI chassis. In multiplexed mode, the SCXI-1520 scanned channels
are kept by the NI-DAQ driver in a scan list. Immediately prior to a
multiplexed scanning operation, the SCXI chassis is programmed with
a module scan list that controls which module sends its output to the
SCXIbus during a scan through the cabled SCXI module.
The list can contain channels in any physical order and the multiplexer can
sequence the channel selection from the scan list in any order. The ordering
of scanned channels need not be sequential. Channels can occur multiple
times in a single scan list. The scan list can contain an arbitrary number
of channels for each module entry in the scan list, limited to a total of
512 channels per DAQ device. This is referred to as flexible scanning
(random scanning). Not all SCXI modules provide flexible scanning.
The module includes first-in first-out (FIFO) memory for storing the
channel scan list defined in your application code. NI-DAQ drivers load the
FIFO based on the channel assignments you make in your application. You
need not explicitly program the module FIFO as this is done automatically
for you by the NI-DAQ driver.
When you configure a module for multiplexed mode operation, the routing of
multiplexed signals to the DAQ device depends on which module in the SCXI
system is cabled to the DAQ device. There are several possible scenarios for
routing signals from the multiplexed modules to the DAQ device.
If the scanned SCXI-1520 module is not directly cabled to the DAQ device,
the module sends its signals through the SCXIbus to the cabled module.
The cabled module, whose routing is controlled by the SCXI chassis, routes
SCXI-1520 User Manual
4-34
ni.com
Chapter 4
Theory of Operation
the SCXIbus signals to the DAQ device through the CH 0 pin on its rear
signal connector.
If the DAQ device scans the cabled module, the module routes its input
signals through the CH 0 pin on its rear signal connector to the DAQ
device CH 0.
Multiplexed mode scanning acquisition rates have limitations that are
determined based on the hardware in the system, the mode of operation,
and SS/H. Refer to the Simultaneous Sample and Hold section for
equations that can help you determine maximum acquisition rates
with SS/H enabled. If SS/H is disabled and the system is configured for
multiplexed mode operation, the maximum sampling rate is determined
by the slower of the maximum sample rate of the DAQ device and the
maximum multiplexing rate of SCXI. The maximum multiplexing rate
of SCXI is 333 kHz. If the DAQ device can sample more quickly than
333 kHz, then the maximum multiplexing rate of SCXI is the limiting
factor. If the DAQ device can sample at 333 kS/s, then the DAQ device’s
sample rate is the limiting factor on the maximum acquisition rate of the
system in multiplexed mode operation.
Theory of Parallel Mode Operation
Parallel mode is ideal for high speed acquisitions. In parallel mode,
the eight conditioned analog output signals at the rear signal connector
of the SCXI-1520, shown in Figure 4-16, are connected directly to the
eight analog input channels on the DAQ device. When the SCXI-1520
operates in parallel mode, the DAQ device performs multiplexed scans
of the SCXI-1520 parallel outputs. The SCXI-1520 module does not
multiplex the channels.
Traditional NI-DAQ (Legacy) driver software can only control the
SCXI-1520 module in multiplexed mode. NI-DAQmx can operate the
SCXI-1520 in both multiplexed and parallel mode.
In parallel mode, SCXI-1520 channels 0 through 7 conditioned outputs are
passed directly to DAQ device channels 0 through 7. The DAQ device
channels should be configured for differential input mode.
Scanning remote-sense channels is not possible when operating the
SCXI-1520 in parallel mode operation. This is because RSX+ and RSX–
terminals are not connected to the 50-pin rear signal connector of the
SCXI-1520 as shown in Figure 4-16, but instead are only connected
internally to the analog multiplexer. The NI-DAQmx driver can still scan
the remote sense channel to utilize for strain task and channel calibration
© National Instruments Corporation
4-35
SCXI-1520 User Manual
Chapter 4
Theory of Operation
and scaling in MAX. However, during operation in your application you
cannot monitor the remote-sense channels if the SCXI-1520 is operating in
parallel mode.
The remote-sense hardware control loop still functions regardless of the mode of
operation correcting the excitation voltage level at all times, even though you cannot
always scan the remote-sense channels.
Note
When SS/H is enabled, the parallel output signals are held while the
channels are scanned by the DAQ device. The T/H circuit of each channel
is in hold mode during this time. This appears as glitches on the parallel
outputs as the SCXI-1520 is sampled by the digitizing DAQ device. Due to
these signal events, NI recommends that you not scan the SCXI-1520
channels with a DAQ device while simultaneously measuring their parallel
outputs with any other analog input device, such as an oscilloscope, unless
you disable SS\H.
It is possible to enable and disable SS/H programmatically in NI-DAQmx,
although NI recommends that you leave SS/H enabled for most
applications. Disabling SS/H for one module disables this feature for all
modules in all chassis that are controlled by the same DAQ device. SS/H
should only be disabled if your application does not require simultaneous
sampling and requires higher acquisition rates than are possible with SS/H
enabled. Refer to the Developing Your Application in NI-DAQmx section
of Chapter 5, Using the SCXI-1520, for more information about
programmatically enabling and disabling SS/H using NI-DAQmx in your
application.
For more information about programmatically performing offset null
compensation in NI-DAQmx and Traditional NI-DAQ (Legacy), refer to
the Developing Your Application in NI-DAQmx section or the Developing
Your Application in Traditional NI-DAQ (Legacy) section, respectively, of
Chapter 5, Using the SCXI-1520.
Parallel mode operation acquisition rates have limitations that are
determined based on the DAQ device you are using and SS/H. Refer to the
Simultaneous Sample and Hold section for equations that can help you
determine maximum acquisition rates with SS/H enabled. If SS/H is
disabled and the system is configured for parallel mode operation, the
maximum sampling rate is determined by the maximum sample rate of the
DAQ device. The 333 kHz maximum SCXI multiplexing rate is not a
limitation in parallel mode operation. Therefore, if the DAQ device can
sample more quickly than 333 kHz, the SCXI-1520 configured for parallel
mode operation is not the limiting factor.
SCXI-1520 User Manual
4-36
ni.com
Using the SCXI-1520
5
This chapter makes suggestions for developing your application and
provides basic information regarding calibration.
Caution Electrostatic discharges (ESD) of 4 kV or greater may cause the SCXI-1520 to
stop responding, resulting in a lost or erroneous reading. As a result, a software reset may
be required to enhance immunity by restoring functionality in such a condition. A software
reset can be accomplished by calling the DAQmx Reset Device function. The DAQmx
Reset VI is located in the Measurement I/O»NI-DAQmx»Dev Config palette on the
LabVIEW Block Diagram. The Reset Device function is usually used at the beginning or
end of a program. If the Reset Device is used in the middle of a program it will immediately
abort all active tasks associated with a device, disconnect any routes, and return the device
to an initialized state. Aborting a task immediately terminates the currently active
operation, such as a read or a write. Aborting a task puts the task into an unstable but
recoverable state. To recover the task in DAQmx, use DAQmx Start to restart the task or
use DAQmx Stop to reset the task without starting it. The task cannot be recovered in
Traditional DAQ so the task will need to be completely re-setup. For more information on
these functions please see the DAQmx/Traditional DAQ help files.
Developing Your Application in NI-DAQmx
If you are not using an NI ADE, using an NI ADE prior to version 7.0, or are using
an unlicensed copy of an NI ADE, additional dialog boxes from the NI License Manager
appear allowing you to create a task or global channel in unlicensed mode. These messages
continue to appear until you install version 7.0 or later of an NI ADE.
Note
This section describes how to configure and use NI-DAQmx to control the
SCXI-1520 in LabVIEW, LabWindows/CVI, and Measurement Studio.
These ADEs provide greater flexibility and access to more settings than
MAX, but you can use ADEs in conjunction with MAX to quickly create a
customized application.
© National Instruments Corporation
5-1
SCXI-1520 User Manual
Chapter 5
Using the SCXI-1520
Typical Program Flowchart
Figure 5-1 shows a typical program flowchart for creating a task to
configure channels, take a measurement, analyze the data, present the data,
stop the measurement, and clear the task.
SCXI-1520 User Manual
5-2
ni.com
Chapter 5
Yes
Create Task Using
DAQ Assistant?
Using the SCXI-1520
No
Create a Task
Programmatically
Yes
Create Task in
DAQ Assistant
or MAX
Create Another
Channel?
Create Strain or Custom
Voltage with Excitation Channel
No
Hardware
Timing/Triggering?
No
No
Further Configure
Channels?
Yes
Yes
Adjust Timing Settings
Configure Channels
Perform
Offset
Null?
Yes
Yes
Bridge Null
Operation
Analyze Data?
Process
Data
No
No
Perform
Shunt
Calibration?
Yes
Yes
No
Display Data?
Graphical
Display Tools
Shunt Calibration
Operation
Yes
Start Measurement
No
Continue Sampling?
No
Read Measurement
Stop Measurement
Clear Task
Figure 5-1. Typical Program Flowchart
© National Instruments Corporation
5-3
SCXI-1520 User Manual
Chapter 5
Using the SCXI-1520
General Discussion of Typical Flowchart
The following sections briefly discuss some considerations for a few of the
steps in Figure 5-1. These sections are meant to give an overview of some
of the options and features available when programming with NI-DAQmx.
Creating a Task Using DAQ Assistant or
Programmatically
When creating an application, you must first decide whether to create the
appropriate task using the DAQ Assistant or programmatically in the ADE.
Developing your application using DAQ Assistant gives you the ability to
configure most settings such as measurement type, selection of channels,
bridge configuration, excitation voltage, signal input limits, task timing,
and task triggering. You can access the DAQ Assistant through MAX
or your NI ADE. Choosing to use the DAQ Assistant can simplify the
development of your application. NI recommends creating tasks using the
DAQ Assistant for ease of use, when using a sensor that requires complex
scaling, or when many properties differ between channels in the same task.
If you are using an ADE other than an NI ADE, or if you want to explicitly
create and configure a task for a certain type of acquisition, you can
programmatically create the task from your ADE using functions or VIs.
If you create a task using the DAQ Assistant, you can still further configure
the individual properties of the task programmatically with functions
or property nodes in your ADE. NI recommends creating a task
programmatically if you need explicit control of programmatically
adjustable properties of the DAQ system.
Programmatically adjusting properties for a task created in the DAQ
Assistant overrides the original, or default, settings only for that session.
The changes are not automatically saved to the task configuration. The next
time you load the task, the task uses the settings originally configured in
the DAQ Assistant. Refer to the NI-DAQmx Help for information on
programmatically saving tasks.
Adjusting Timing and Triggering
There are several timing properties that you can configure through the
DAQ Assistant or programmatically using function calls or property nodes.
If you create a task in the DAQ Assistant, you can still modify the timing
properties of the task programmatically in your application.
SCXI-1520 User Manual
5-4
ni.com
Chapter 5
Using the SCXI-1520
When programmatically adjusting timing settings, you can set the task to
acquire continuously, acquire a buffer of samples, or acquire one point at a
time. For continuous acquisition, you must use a While Loop around the
acquisition components even if you configured the task for continuous
acquisition using MAX or the DAQ Assistant. For continuous and buffered
acquisitions, you can set the acquisition rate and the number of samples to
read in the DAQ Assistant or programmatically in your application. By
default, the clock settings are automatically set by an internal clock based
on the requested sample rate. You also can select advanced features such as
clock settings that specify an external clock source, internal routing of the
clock source, or select the active edge of the clock signal.
Configuring Channel Properties
All ADEs used to configure the SCXI-1520 access an underlying set of
NI-DAQmx properties. Table 5-1 shows some of these properties. You can
use Table 5-1 to determine what kind of properties you need to set to
configure the module for your application. For a complete list of
NI-DAQmx properties, refer to your ADE help file.
You cannot adjust some properties while a task is running. For these properties, you
must stop the task, make the adjustment, and re-start the application. Figure 5-1 assumes
all properties are configured before the task is started.
Note
Table 5-1. NI-DAQmx Properties
Property
Short Name
Description
Analog Input»General Properties»
Advanced»Range»High
AI.Rng.High
Specifies the upper
limit of the input
range.
Analog Input»General Properties»
Advanced»Range»Low
AI.Rng.Low
Specifies the lower
limit of the input
range.
Analog Input»General Properties»
Filter»Analog Lowpass»Enable
AI.Lowpass.Enable
Enables the lowpass
filter of the channel.
© National Instruments Corporation
5-5
SCXI-1520 User Manual
Chapter 5
Using the SCXI-1520
Table 5-1. NI-DAQmx Properties (Continued)
Property
Short Name
Description
Analog Input»General Properties»
Filter»Analog Lowpass»Cutoff
Frequency
AI.Lowpass.CutoffFreq
Specifies in hertz
the frequency
corresponding to the
–3 dB cutoff of the
filter. You can specify
10, 100, 1000, or
10000.
Analog Input»General Properties»
Signal Conditioning»Bridge»
Configuration
AI.Bridge.Cfg
Specifies the sensor
Wheatstone bridge
type.
Analog Input»General Properties»
Signal Conditioning»Bridge»
Shunt Cal»Shunt Cal Enable
AI.Bridge.ShuntCal.Enable
Specifies whether
to place the shunt
calibration resistor
across one arm of the
bridge.
Analog Input»General Properties»
Signal Conditioning»Bridge»
Shunt Cal»Shunt Cal Select
AI.Bridge.ShuntCal.Select
Specifies which
calibration switch(es)
to enable.
Analog Input»General Properties»
Signal Conditioning»Excitation»
Value
AI.Excit.Val
Specifies the amount
of excitation in volts.
Analog Input»Strain»Strain Gage»
Configuration
AI.StrainGage.Cfg
Specifies the
strain-gauge
configuration type.
Analog Input»General Properties»
Signal Conditioning»Bridge»
Nominal Resistance
AI.Bridge.NomResistance
Specifies in ohms the
resistance of the bridge
in an unloaded
condition.
Analog Input»Strain»Strain Gage»
Gage Factor
AI.StrainGage.GageFactor
Specifies the
sensitivity of the
strain gauge.
Analog Input»Strain»Strain Gage»
Poisson Ratio
AI.StrainGage.PoissonRatio
Specifies the ratio of
lateral strain to axial
strain in the specimen
material.
SCXI-1520 User Manual
5-6
ni.com
Chapter 5
Using the SCXI-1520
Table 5-1. NI-DAQmx Properties (Continued)
Property
Short Name
Description
Analog Input»General Properties»
Signal Conditioning»Bridge»
Initial Bridge Voltage
AI.Bridge.InitialVoltage
Specifies in volts the
output voltage of the
bridge in the unloaded
condition.
Analog Input»General Properties»
Signal Conditioning»Bridge»
Balance»Coarse Potentiometer
Property
AI.Bridge.Balance.CoarsePot
Specifies by how much
to compensate for
offset in the signal.
This value can be
between 0 and 127.
Analog Input»General Properties»
Signal Conditioning»Bridge»
Balance»Fine Potentiometer
Property
AI.Bridge.Balance.FinePot
Specifies by how much
to compensate for
offset in the signal.
This value can be
between 0 and 4095.
Analog Input»General Properties»
Signal Conditioning»Excitation»
Source
AI.Excit.Src
Specifies the source of
excitation.
Analog Input»General Properties»
Advanced»Sample and Hold Enable
AI.SampAndHold.Enable
Specifies whether
to enable the
sample-and-hold
circuitry of the device.
This is not a complete list of NI-DAQmx properties and does not include every
property you may need to configure your application. It is a representative sample of
important properties to configure for strain and Wheatstone bridge measurements. For a
complete list of NI-DAQmx properties and more information about NI-DAQmx properties,
refer to your ADE help file.
Note
Performing Offset Null Compensation
The SCXI-1520 provides offset null compensation circuitry to adjust signal
voltages to proper levels when the strain gauge or bridge sensor is at rest
(unstrained). For most sensors, offset null compensation removes an initial
voltage offset from the Wheatstone bridge. If you are measuring strain, you
can use a strain task or global channel to perform offset null compensation.
The offset null compensation can be performed during the configuration of
the global channel(s) or programmatically using the DAQmx Offset Null
function (in LabVIEW, use Daqmx Perform Bridge Offset Nulling
© National Instruments Corporation
5-7
SCXI-1520 User Manual
Chapter 5
Using the SCXI-1520
Calibration.vi; in CVI, use the
DAQmxPerformBridgeOffsetNullingCal function). Refer to the
Creating a Strain Global Channel or Task section of Chapter 3,
Configuring and Testing, for information about offset null compensation
when in MAX. If you are not measuring strain or would like to adjust the
offset to an arbitrary voltage, you can manually adjust the coarse and fine
potentiometer settings using properties.
For more information about offset null compensation, refer to the Offset
Null Compensation section of Chapter 4, Theory of Operation.
Performing Shunt Calibration
Shunt calibration is a process used to obtain a gain adjust factor, which
corrects for system gain error and discrepancies between the nominal gauge
factor and actual gauge factor of the strain gauge. If you are measuring
strain, you can use a strain task or global channel to perform shunt
calibration. The shunt calibration is performed during the configuration of
the global channel(s). Refer to the Creating a Strain Global Channel or
Task section of Chapter 3, Configuring and Testing, for information about
shunt calibration in MAX.
To manually perform shunt calibration, refer to the Shunt Calibration
section of Chapter 4, Theory of Operation.
Acquiring, Analyzing, and Presenting
After configuring the task and channels, you can start the acquisition, read
measurements, analyze the data returned, and display it according to the
needs of your application. Typical methods of analysis include digital
filtering, averaging data, performing harmonic analysis, applying a custom
scale, or adjusting measurements mathematically.
Some custom scaling applications require the actual excitation voltage
applied to the bridge instead of the nominal excitation voltage output by the
SCXI-1520. You can scan the remote sense pins RSX+ and RSX– with the
DAQmx physical channels DevX/_pPosX and DevX/_pNegX to find the
actual excitation voltage. Take the difference of the two physical channels
to determine the actual excitation applied to the bridge and use this value in
the scaling equation.
Note If RSX+ and RSX– are not wired to the bridge where PX+ and PX– connect, _ pPosX
and _pNegX only measure the internal excitation. Measuring this voltage does not correct
for the voltage drop in the excitation leads.
SCXI-1520 User Manual
5-8
ni.com
Chapter 5
Using the SCXI-1520
NI provides powerful analysis toolsets for each NI ADE to help you
perform advanced analysis on the data without requiring you to have a
programming background. After you acquire the data and perform any
required analysis, it is useful to display the data in a graphical form or log
it to a file. NI ADEs provide easy-to-use tools for graphical display, such as
charts, graphs, slide controls, and gauge indicators. NI ADEs have tools
that allow you to easily save the data to files such as spread sheets for easy
viewing, ASCII files for universality, or binary files for smaller file sizes.
Completing the Application
After you have completed the measurement, analysis, and presentation of
the data, it is important to stop and clear the task. This releases any memory
used by the task and frees up the DAQ hardware for use in another task.
Note
In LabVIEW, tasks are automatically cleared.
Developing an Application Using LabVIEW
This section describes in more detail the steps shown in the typical program
flowchart in Figure 5-1, such as how to create a task in LabVIEW and
configure the channels of the SCXI-1520. If you need more information or
for further instructions, select Help»VI, Function, & How-To Help from
the LabVIEW menu bar.
Note Except where otherwise stated, the VIs in Table 5-2 are located on the Functions»
All Functions»NI Measurements»DAQmx - Data Acquisition subpalette and
accompanying subpalettes in LabVIEW.
Table 5-2. Programming a Task in LabVIEW
Flowchart Step
VI or Program Step
Create Task in DAQ Assistant
Create a DAQmx Task Name Constant located on the
Controls»All Controls»I/O»DAQmx Name Controls
subpalette, right-click it, and select New Task (DAQ
Assistant).
Create a Task
Programmatically
(optional)
DAQmx Create Task.vi—This VI is optional if you created
© National Instruments Corporation
and configured your task using the DAQ Assistant. However, if
you use it in LabVIEW, any changes you make to the task will not
be saved to a task in MAX.
5-9
SCXI-1520 User Manual
Chapter 5
Using the SCXI-1520
Table 5-2. Programming a Task in LabVIEW (Continued)
Flowchart Step
Create AI Strain Channel
(optional)
or
Create AI Custom Voltage
with Excitation Channel
(optional)
VI or Program Step
DAQmx Create Virtual Channel.vi (AI Voltage by default,
to change to a strain gauge channel, click AI Voltage and select
Analog Input»Strain»Strain Gage.)—This VI is optional if
you created and configured your task and channels using the
DAQ Assistant. Any channels created with this VI are not saved
in the DAQ Assistant. They are only available for the present
session of the task in LabVIEW.
Adjust Timing Settings
(optional)
DAQmx Timing.vi (Sample Clock by default)—This VI is
optional if you created and configured your task using the DAQ
Assistant. Any timing settings modified with this VI are not
saved in the DAQ Assistant. They are only available for the
present session.
Configure Channels
(optional)
DAQmx Channel Property Node, refer to the Using a DAQmx
Channel Property Node in LabVIEW section for more
information. This step is optional if you created and fully
configured the channels using the DAQ Assistant. Any channel
modifications made with a channel property node are not saved
in the task in the DAQ Assistant. They are only available for the
present session.
Perform Offset Null
Compensation
Daqmx Perform Bridge Offset Nulling
Calibration.vi or you can perform offset null compensation
when you create and configure your channels using the DAQ
Assistant. Refer to the Creating a Strain Global Channel or Task
section of Chapter 3, Configuring and Testing, for information
about offset null compensation in MAX.
Perform Shunt Calibration
You can perform shunt calibration when you create and configure
your channels using the DAQ Assistant. Refer to the Creating a
Strain Global Channel or Task section of Chapter 3, Configuring
and Testing, for information about shunt calibration in MAX.
Start Measurement
DAQmx Start Task.vi
Read Measurement
DAQmx Read.vi
Analyze Data
Some examples of data analysis include filtering, scaling,
harmonic analysis, or level checking. Some data analysis tools
are located on the Functions»Signal Analysis subpalette and on
the Functions»All Functions»Analyze subpalette.
SCXI-1520 User Manual
5-10
ni.com
Chapter 5
Using the SCXI-1520
Table 5-2. Programming a Task in LabVIEW (Continued)
Flowchart Step
VI or Program Step
Display Data
You can use graphical tools such as charts, gauges, and graphs
to display your data. Some display tools are located on the
Controls»Numeric Indicators subpalette and Controls»
All Controls»Graph subpalette.
Continue Sampling
For continuous sampling, use a While Loop. If you are using
hardware timing, you also need to set the DAQmx Timing.vi
sample mode to Continuous Samples. To do this, right-click the
terminal of the DAQmx Timing.vi labeled sample mode and
click Create»Constant. Click the box that appears and select
Continuous Samples.
Stop Measurement
DAQmx Stop Task.vi (This VI is optional, clearing the task
automatically stops the task.)
Clear Task
DAQmx Clear Task.vi
Using a DAQmx Channel Property Node in LabVIEW
Note
With the SCXI-1520, you must use property nodes to disable SS/H.
You can use property nodes in LabVIEW to manually configure
the channels. To create a LabVIEW property node, complete the
following steps:
1.
Launch LabVIEW.
2.
Create the property node in a new VI or in an existing VI.
3.
Open the block diagram view.
4.
From the Functions toolbox, select All Functions»
NI Measurements»DAQmx - Data Acquisition, and select DAQmx
Channel Property Node.
5.
Configure your channels. The initial ActiveChan item allows you to
specify exactly what channel(s) you want to configure. If you want to
configure several channels with different properties, separate the lists
of properties with another Active Channels box and assign the
appropriate channel to each list of properties.
If you do not use Active Channels, the properties are set on all of the channels in
the task.
Note
© National Instruments Corporation
5-11
SCXI-1520 User Manual
Chapter 5
Using the SCXI-1520
6.
Right-click ActiveChan, select Add Element, and left-click in the
new ActiveChan box. Navigate through the menus, and select the
property you wish to define.
7.
Change the property to read or write to either get the property or write
a new value. Right-click the property, go to Change To, and select
Write, Read, or Default Value.
8.
After you have added the property to the property node, right-click
the terminal to change the attributes of the property, add a control,
constant, or indicator.
Figure 5-2. LabVIEW Channel Property Node with Filtering Enabled
at 10 kHz and SS/H Disabled
9.
To add another property to the property node, right-click an existing
property and left-click Add Element. To change the new property,
left-click it and select the property you wish to define.
Refer to the LabVIEW Help for information about property nodes and specific
NI-DAQmx properties.
Note
Specifying Channel Strings in NI-DAQmx
Use the channel input of DAQmx Create Channel to specify the
SCXI-1520 channels. The input control/constant has a pull-down menu
showing all available external channels. You can right-click the physical
channel input, select I/O Name Filtering, and check Internal Channels.
This allows you to select the SCXI-1520 excitation channels. The strings
take one of the following forms:
•
single device identifier/channel number—for example SC1Mod1/ch0
•
multiple, noncontinuous channels—for example SC1Mod1/ch0,
SC1Mod1/ch4
SCXI-1520 User Manual
5-12
ni.com
Chapter 5
Using the SCXI-1520
•
multiple continuous channels—for example SC1Mod1/ch0:4
(channels 0 through 4)
•
positive or negative excitation on a particular SCXI-1520 channel—for
example SC1Mod1/_pPos0, SC1Mod1/_pNeg0
When you have a task containing SCXI-1520 channels, you can set the
properties of the channels programmatically using the DAQmx Channel
Property Node.
Follow the general programming flowchart or open an example to build a
basic strain virtual channel. You can use property nodes in LabVIEW to
control, configure, and customize the NI-DAQmx task and SCXI-1520.
To create a LabVIEW property node, complete the following steps:
1.
Launch LabVIEW.
2.
Create the property node in a new Virtual Instrument (VI) or in an
existing VI.
3.
Open the block diagram view.
4.
From the Functions tool bar, select NI Measurements,
DAQmx - Data Acquisition, and select the type of property node you
wish to configure.
5.
The ActiveChan item allows you to specify what channel(s) you want
to configure. If you want to configure several channels with different
properties, separate the lists of properties with another Active
Channels box, and assign the appropriate channel to each list of
properties.
6.
Right-click ActiveChan and select Add Element. Left-click the new
ActiveChan box. Navigate through the menus and select the property
you wish to define.
7.
You must change the property to read or write to either get the property
or write a new value. Right-click the property, go to Change To, and
select Write, Read, or Default Value.
8.
After you have added the property to the property node, right-click
the terminal to change the attributes of the property, add a control,
constant, or indicator.
9.
To add another property to the property node, right-click an existing
property and left-click Add Element. To change the new property,
left-click it and select the property you wish to define.
Refer to the LabVIEW Help for information about property nodes and specific
NI-DAQmx properties.
Note
© National Instruments Corporation
5-13
SCXI-1520 User Manual
Chapter 5
Using the SCXI-1520
Text Based ADEs
You can use text based ADEs such as LabWindows/CVI, Measurement
Studio, Visual Basic, .NET, and C# to create code for using the
SCXI-1520.
LabWindows/CVI
LabWindows/CVI works with the DAQ Assistant in MAX to generate
code for a strain task. You can then use the appropriate function
call to modify the task. To create a configurable channel or task in
LabWindows/CVI, complete the following steps:
1.
Launch LabWindows/CVI.
2.
Open a new or existing project.
3.
From the menu bar, select Tools»Create/Edit DAQmx Tasks.
4.
Choose Create New Task In MAX or Create New Task In Project
to load the DAQ Assistant.
5.
Configure the NI-DAQmx strain task following the instructions in
the Creating a Strain Global Channel or Task section of Chapter 3,
Configuring and Testing.
6.
The DAQ Assistant creates the code for the task based on the
parameters you define in MAX and the device defaults. To change
a property of the channel programmatically, use the
DAQmxSetChanAttribute function.
Refer to the NI LabWindows/CVI Help for more information on creating NI-DAQmx
tasks in LabWindows/CVI and NI-DAQmx property information.
Note
Measurement Studio (Visual Basic, .NET, and C#)
When creating a strain task in Visual Basic .NET and C#, follow the
general programming flow in Figure 5-1. You can then use the appropriate
function calls to modify the task. This example creates a new task and
configures an NI-DAQmx strain channel on the SCXI-1520. You can use
the same functions for Visual Basic .NET and C#.
In this example, an analog input channel object is used since reading the
voltage from a Wheatstone bridge configuration is an analog input
operation. The following text is a function prototype example:
void AIChannelCollection.CreateStrainGageChannel(
System.String physicalChannelName,
System.String nameToAssignChannel,
System.Double minVal,
SCXI-1520 User Manual
5-14
ni.com
Chapter 5
Using the SCXI-1520
System.Double maxVal,
AIStrainGageConfiguration strainGageConfiguration,
AIExcitationSource excitationSource,
System.Double excitationValue,
System.Double gageFactor,
System.Double initialBridgeVoltage,
System.Double normalGageResist,
System.Double poissonRatio,
System.Double leadWireResist,
AIStrainUnits units);
To actually create and configure the channel, you would enter something
resembling the following example code:
Task myTask = new
NationalInstruments.DAQmx.Task(“myTaskName”);
MyTask.CreateStrainGageChannel (
“SC1Mod1/ai0”, // System.String physicalChannelName
“strain0”, // System.String nameToAssignChannel
-0.001, // System.Double minVal
0.001, // System.Double maxVal
AIStrainGageConfiguration.FullBridgeIII, //
AIStrainGageConfiguration strainGageConfiguration
AIExcitationSource.Internal, // AIExcitationSource
excitationSource
3.3, // System.Double excitationValue
2.0, // System.Double gageFactor
0.0, // System.Double initialBridgeVoltage
120.0, // System.Double normalGageResist
0.3, // System.Double poissonRatio
0.0, // System.Double leadWireResist
AIStrainUnits.Strain); // AIStrainUnits units
// setting attributes after the channel is created
AIChannel myChannel = myTask.AIChannels[“strain0”];
myChannel.LowpassCutoffFrequency = 10.0;
myChannel.LowpassEnable = true;
myChannel.AutoZeroMode = AIAutoZeroMode.Once;
You can change any of the properties at a later time. For example, to change
the filter settings of myChannel, enter the following lines:
AIChannel myChannel = myTask.AIChannels[“strain 0”];
myChannel.LowpassCutoffFrequency = 10.0;
myChannel.LowpassEnable = true;
© National Instruments Corporation
5-15
SCXI-1520 User Manual
Chapter 5
Using the SCXI-1520
Modify the example code above or the code from one of the shipping
examples as needed to suit your application. Refer to the Other Application
Documentation and Material section for the location of program examples.
Notes You can create and configure the strain task in MAX and load it into your application
with the function call NationalInstruments.DAQmx.DaqSystem.Local.LoadTask
Refer to the NI Measurement Studio Help for more information on creating NI-DAQmx
tasks in LabWindows/CVI and NI-DAQmx property information.
Programmable NI-DAQmx Properties
All of the different ADEs that configure the SCXI-1520 access an
underlying set of NI-DAQmx properties. Table 5-3 provides a list of some
of the properties that configure the SCXI-1520. You can use this list to
determine what kind of properties you need to set to configure the device
for your application. For a complete list of NI-DAQmx properties, refer to
your ADE help file.
Table 5-3. NI-DAQmx Properties
Property
Short Name
Description
Analog Input»General Properties»
Advanced»Range»High
AI.Rng.High
Specifies the upper limit
of the input range on the
digitizer device.
Analog Input»General Properties»
Advanced»Range»Low
AI.Rng.Low
Specifies the lower limit
of the input range on the
digitizer device.
Analog Input»General Properties»
Advanced»Sample and Hold Enable
AI.SampAndHold.Enable
Specifies whether
to enable the
sample-and-hold
circuitry of the device.
Analog Input»General Properties»
Signal Conditioning»Bridge»
Configuration
AI.Bridge.Cfg
Specifies whether the
sensor is a type of
Wheatstone bridge.
Analog Input»General Properties»
Signal Conditioning»Bridge»
Shunt Cal»Shunt Cal Enable
AI.Bridge.ShuntCal.Enable
Specifies whether
to place the shunt
calibration resistor
across one arm of the
bridge.
SCXI-1520 User Manual
5-16
ni.com
Chapter 5
Using the SCXI-1520
Table 5-3. NI-DAQmx Properties (Continued)
Property
Short Name
Description
Analog Input»General Properties»
Signal Conditioning»Bridge»
Shunt Cal»Shunt Cal Select
AI.Bridge.ShuntCal.Select
Specifies which
calibration switch(es) to
enable.
Analog Input»General Properties»
Signal Conditioning»Excitation»
Source
AI.Excit.Src
Specifies the source of
excitation.
Analog Input»General Properties»
Signal Conditioning»Excitation»
Value
AI.Excit.Val
Specifies the amount of
excitation in volts.
Analog Input»Strain»Strain Gage»
Configuration
AI.StrainGage.Cfg
Specifies the
strain-gauge
configuration type.
Analog Input»General Properties»
Signal Conditioning»Bridge»
Nominal Resistance
AI.Bridge.NomResistance
Specifies in ohms the
resistance of the bridge
in an unloaded
condition.
Analog Input»Strain»Strain Gage»
Gage Factor
AI.StrainGage.GageFactor
Specifies the sensitivity
of the strain gauge.
Analog Input»Strain»Strain Gage»
Poisson Ratio
AI.StrainGage.PoissonRatio
Specifies the ratio of
lateral strain to axial
strain in the specimen
material.
Analog Input»General Properties»
Signal Conditioning»Bridge»
Initial Bridge Voltage
AI.Bridge.InitialVoltage
Specifies in volts the
output voltage of the
bridge in the unloaded
condition.
Analog Input»Strain»Units
AI.Strain.Units
Specifies the units to
use to return strain
measurements from
the channel.
Analog Input»General Properties»
Advanced»Gain and Offset»
Gain Value
AI.Gain
Specifies a gain factor
to apply to the signal
conditioning portion
of the channel.
© National Instruments Corporation
5-17
SCXI-1520 User Manual
Chapter 5
Using the SCXI-1520
Table 5-3. NI-DAQmx Properties (Continued)
Property
Short Name
Description
Analog Input»General Properties»
Advanced»High Accuracy Settings»
Auto Zero Mode
AI.AutoZeroMode
Specifies when to
measure ground.
NI-DAQmx then
subtracts the voltage
either on every sample
or only once, depending
on the setting.
Analog Input»Measurement Type
AI.MeasType
Indicates the
measurement to take
with the analog input
channel.
This is not a complete list of NI-DAQmx properties and does not include every
property you may need to configure your application. It is a representative sample of
important properties to configure for strain and Wheatstone bridge measurements. For a
complete list of NI-DAQmx properties and more information on NI-DAQmx properties,
refer to your ADE help file.
Note
Developing Your Application in Traditional NI-DAQ
(Legacy)
If you are not using an NI ADE, using an NI ADE prior to version 7.0, or are using
an unlicensed copy of an NI ADE, additional dialog boxes from the NI License Manager
appear allowing you to create a task or global channel in unlicensed mode. These messages
continue to appear until you install version 7.0 or later of an NI ADE.
Note
This section describes how to configure and use Traditional NI-DAQ
(Legacy) to control the SCXI-1520 in LabVIEW, LabWindows/CVI,
Measurement Studio, and other text-based ADEs. These NI ADEs provide
greater flexibility and access to more settings than MAX, but you can use
ADEs in conjunction with MAX to quickly create a customized
application.
SCXI-1520 User Manual
5-18
ni.com
Chapter 5
Using the SCXI-1520
Traditional NI-DAQ (Legacy) in LabVIEW
LabVIEW is a graphical programming environment for test and
measurement application development with built-in easy to use tools for
data acquisition, analysis, and display. You can use functional graphical
blocks called subVIs to easily create a custom application that fully utilizes
the SCXI-1520 programmable functionality. Traditional NI-DAQ
(Legacy) provides several standard data acquisition subVIs as well as
subVIs specifically for use with the SCXI-1520.
For applications using Traditional NI-DAQ (Legacy) in LabVIEW, there
are two typical methods of addressing SCXI-1520 channels—virtual
channels (specifically strain virtual channels) and SCXI channel strings.
Depending on the needs of your application, you choose one of these
channel-addressing methods to use in your LabVIEW application.
The strain virtual channel provides scaling for strain gauges, provides an
easy interface for offset null compensation and shunt calibration, and
allows you to select any name for the SCXI-1520 strain channel that you
choose without additional code. When you use virtual channels, the
maximum number of channels per E Series DAQ device is 512 in
multichassis systems. NI recommends using the strain virtual channel
for ease of use. Refer to Appendix B, Using SCXI Channel Strings with
Traditional NI-DAQ (Legacy) 7.0 or Later, for more information on how to
create a strain virtual channel.
The SCXI channel string allows you to combine large numbers of channels
into fewer scan list entries, to measure the signal voltage level directly for
custom scaling, and to dynamically perform an offset null compensation in
your application. NI recommends using SCXI channel strings for more
advanced applications. In LabVIEW, an array of these channel strings
configures multiple modules for scanning. When using SCXI channel
strings, you can scan up to 3,072 channels in a multichassis system using
a single DAQ device. Refer to Appendix B, Using SCXI Channel Strings
with Traditional NI-DAQ (Legacy) 7.0 or Later, for more information
about using SCXI channel strings.
You cannot mix virtual channels with the SCXI channel strings within the same
channel string array.
Note
To use virtual channels, enter the name of a virtual channel into the analog
input channel string. If using multiple virtual channels, enter them in a
different index in the channel string array, or separate them using a comma.
© National Instruments Corporation
5-19
SCXI-1520 User Manual
Chapter 5
Using the SCXI-1520
Since you can randomly scan analog input virtual channels, you can enter
the virtual channels you want to scan in any order or repeatedly in a channel
string array.
Typical Program Flow
After you have determined how you want to address the channels and
whether you want to configure the SCXI-1520 in MAX or LabVIEW, you
can design your application using a typical program flow such as the one
shown in Figure 5-3.
SCXI-1520 User Manual
5-20
ni.com
Chapter 5
Virtual Channel
Using the SCXI-1520
Use
SCXI Channel String
Virtual Channel
or SCXI Channel
String
Configure
Acquisition Settings
Create Virtual
Channel in MAX
Configure
Mode Properties
Perform
Offset Null?
Yes
SCXI Strain Null.vi
No
Perform Shunt
Calibration?
Yes
Shunt Calibration
Procedure
No
Start Acquisition
Take Measurements
Continue
Sampling?
Yes
No
Scale, Analyze,
and Display
Clear Acquisition
Error Handling
Figure 5-3. Typical SCXI-1520 Program Flow with Traditional NI-DAQ (Legacy)
© National Instruments Corporation
5-21
SCXI-1520 User Manual
Chapter 5
Using the SCXI-1520
Configuring the SCXI-1520 Settings Using Traditional NI-DAQ (Legacy)
in LabVIEW
You can configure SCXI-1520 settings, perform offset null compensation,
and perform shunt calibration in MAX using the strain virtual channel.
To configure and control the SCXI-1520 from LabVIEW, use the
AI Parameter VI. You can find AI Parameter VI in the function subpalette
Data Acquisition»Analog Input»Advanced Analog Input.
A parameter changed by the AI Parameter VI takes effect in hardware when
AI Start VI is called, not when AI Parameter VI is called. The AI parameter
VI merely changes the configuration in the driver memory. When called,
the AI Start VI reads the configuration settings in the driver memory and
then sends the actual control information to the SCXI-1520 module. A
setting established through AI Parameter VI is only valid for the LabVIEW
session and does not change the setting in MAX.
You can use the AI Parameter VI to configure the SCXI-1520 settings
shown in Table 5-4.
Table 5-4. Settings for Configuring the SCXI-1520 Through the AI Parameter
SoftwareConfigurable
Setting
Allowable Settings
(Float In, Boolean In, or Value In)
AI Parameter VI
Parameter
Name
Value
Data Type
Values
Excitation
Level
SCXI DC
Voltage
Excitation
17
Float In (dbl)
0.000, 0.625, 1.125, 1.875,
2.500, 3.125, 3.750, 5.375,
5.000, 5.625, 6.125, 6.875,
7.500, 8.125, 8.750, 9.375,
10.00
Filter
Bandwidth
Filter Setting
14
Float In (dbl)
0.0 (disable filter), 10.0,
100.0, 1000.0, 10000.0
Bridge Type
SCXI
Connection
Type
19
Value In (u16)
9 = Quarter Bridge
10 = Half Bridge
11 = Full Bridge
Coarse
Potentiometer
SCXI Coarse
Potentiometer
24
Float In (dbl)
Any integer between 0 and
127, with 62 at mid-scale
Fine
Potentiometer
SCXI Fine
Potentiometer
23
Float In (dbl)
Any integer between 0 and
4095, with 2048 at mid-scale
SCXI-1520 User Manual
5-22
ni.com
Chapter 5
Using the SCXI-1520
Table 5-4. Settings for Configuring the SCXI-1520 Through the AI Parameter (Continued)
SoftwareConfigurable
Setting
Allowable Settings
(Float In, Boolean In, or Value In)
AI Parameter VI
Parameter
Name
Value
Data Type
Values
Shunt A
Enable
SCXI Shunt A
Enabled
25
Boolean In (T/F)
TRUE turns switch ON
FALSE turns switch OFF
Shunt B
Enable
SCXI Shunt B
Enabled
26
Boolean In (T/F)
TRUE turns switch ON
FALSE turns switch OFF
An example of using the AI Parameter VI to control an SCXI-1520 is
shown in Figure 5-4.
© National Instruments Corporation
5-23
SCXI-1520 User Manual
Chapter 5
Using the SCXI-1520
Above settings become active
when this AI Start is executed.
Figure 5-4. Using the AI Parameter VI to Set Up the SCXI-1520
Performing Offset Null Compensation Using Traditional NI-DAQ
(Legacy) in LabVIEW
The SCXI-1520 provides offset null compensation to adjust signal voltages
to remove an initial signal voltage offset from the Wheatstone bridge
sensor. If you are measuring strain, you can use the strain virtual channel
in Traditional NI-DAQ (Legacy) to perform offset null compensation,
shunt calibration, and to properly scale strain measurements. The
offset null compensation and shunt calibration are performed during
configuration of the strain virtual channel. Refer to Appendix B, Using
SCXI Channel Strings with Traditional NI-DAQ (Legacy) 7.0 or Later,
for more information about creating a strain virtual channel in MAX.
SCXI-1520 User Manual
5-24
ni.com
Chapter 5
Using the SCXI-1520
After you have created a strain virtual channel, simply use a DAQ channel
control or constant to select the strain virtual channel from a list of all the
virtual channels you have configured in MAX. You can find the DAQ
channel constant in the function subpalette Data Acquisition»Analog
Input. You can find the DAQ channel control in the control subpalette I/O.
If you are using a strain virtual channel, you cannot perform offset null
compensation dynamically in your application. If you need to dynamically
perform an offset null compensation in your application, you must use
SCXI channel strings. For more information about using SCXI channel
strings with the SCXI-1520, refer to Appendix B, Using SCXI Channel
Strings with Traditional NI-DAQ (Legacy) 7.0 or Later. If you are
measuring any other kind of bridge sensor such as a load cell, pressure
sensor, or torque sensor and require the measurement to be displayed in
units of interest for the sensor, you cannot use the strain virtual channel.
This is because the scaling provided by the strain virtual channel returns
measurements in units of microstrain (με) rather than the units of interest
for the sensor. If you require alternative scaling, you can either use an
analog input voltage virtual channel with a custom scale configured in
MAX, or SCXI channel strings and provide scaling in your LabVIEW
application.
To perform an offset null compensation for bridge sensors such as strain
gauges, load cells, pressure sensors, or torque sensors dynamically in your
LabVIEW application, use the SCXI Strain Null VI. You can find the SCXI
Strain Null VI in the function subpalette Data Acquisition»Analog
Input»Calibration and Configuration. The SCXI Strain Null VI only
performs offset null compensation for SCXI channel strings, not virtual
channels.
If you want to explicitly set the potentiometers, you can write an
application program that adjusts the settings of many channels
simultaneously or restores a particular null setting between sessions
without performing a nulling operation each time. To explicitly set or get
the control codes of the potentiometers in Traditional NI-DAQ (Legacy),
use the LabVIEW AI Parameter VI. An example of using the AI Parameter
VI to control an SCXI-1520 is shown in Figure 5-4.
For more information and example programs for setting the offset null
potentiometers, go to ni.com/info and use these info codes: rd1520,
rdnull, and rdxi15.
© National Instruments Corporation
5-25
SCXI-1520 User Manual
Chapter 5
Using the SCXI-1520
Performing Shunt Calibration Using Traditional NI-DAQ (Legacy)
in LabVIEW
Shunt calibration is a process used to obtain a gain adjust factor, which
corrects system gain error and discrepancies between nominal Gauge
Factor and actual Gauge Factor of the strain gauge. If you are measuring
strain, you can use the strain virtual channel in Traditional NI-DAQ
(Legacy) to perform offset null compensation, shunt calibration, and to
properly scale strain measurements. The offset null compensation and
shunt calibration are performed during configuration of the strain virtual
channel. Refer to Appendix B, Using SCXI Channel Strings with
Traditional NI-DAQ (Legacy) 7.0 or Later, for more information about
creating a strain virtual channel in MAX.
Refer to the Shunt Calibration section of Chapter 4, Theory of Operation,
for more information on the process and calculations required for shunt
calibration in your application. To perform shunt calibration for bridge
sensors such as strain gauges, load cells, pressure sensors, or torque sensors
dynamically in your LabVIEW application, use the AI Parameter VI to
programmatically engage and disengage the shunt calibration. As with all
settings that are controlled by the AI Parameter VI, the switch settings take
effect when the next AI Start VI is encountered in your software, not at the
time the AI Parameter VI is called. Either insert a 500 ms delay in your
code or discard the first 500 ms of data after the switches are closed since
the filters in the SCXI-1520 are not fully stabilized until 500 ms have
elapsed. You can find the AI Parameter VI in the function subpalette
Data Acquisition»Analog Input»Advanced Analog Input. An example
of using the AI Parameter VI to control an SCXI-1520 is shown in
Figure 5-4.
NI recommends acquiring a buffer of 1000 samples of a channel with the
shunt resistors engaged, then using the average of this buffer in the shunt
calibration calculations. After you have measured a buffer of data with
the shunt resistors engaged, you can calculate the gain adjust factor to
use to adjust measurements on that channel. If you are performing shunt
calibration on a strain gauge, you can use the equations for simulated
strain found in the Strain-Gauge Theory section of Chapter 4, Theory of
Operation, for the shunt calibration calculations. After you have
determined the correct gain adjust factor, multiply each measurement in
your application by the gain adjust factor for maximum absolute accuracy.
SCXI-1520 User Manual
5-26
ni.com
Chapter 5
Using the SCXI-1520
Configure, Start Acquisition, and Take Readings Using Traditional
NI-DAQ (Legacy) in LabVIEW
After you have performed an offset null compensation, shunt calibration,
and configured the SCXI-1520 settings for your application, you can use
the intermediate analog input functions AI Config VI, AI Start VI, AI Read
VI, and AI Clear VI to create your data acquisition application. You can
find the intermediate data acquisition Traditional NI-DAQ (Legacy)
functions in the function subpalettes Data Acquisition»Analog Input.
NI recommends using the intermediate analog input functions for most
SCXI-1520 applications. For more information about using the
intermediate data acquisition Traditional NI-DAQ (Legacy) functions,
refer to the LabVIEW Measurements Manual. You also can use the
LabVIEW Help for more detailed information about the various inputs and
outputs of these functions.
Converting Scaling Using Traditional NI-DAQ (Legacy) in LabVIEW
The names given the strain-gauge types in Chapter 4, Theory of Operation,
in Figure 4-3, Quarter-Bridge I Circuit Diagram, Figure 4-5,
Quarter-Bridge II Circuit Diagram, Figure 4-7, Half-Bridge Type I Circuit
Diagram, Figure 4-9, Half-Bridge Type II Circuit Diagram, Figure 4-11,
Full-Bridge Type I Circuit Diagram, Figure 4-13, Full-Bridge Type II
Circuit Diagram, and Figure 4-15, Full-Bridge Type III Circuit Diagram,
directly correspond to bridge selections in MAX and the LabVIEW
Convert Strain Gauge Reading VI. You find this VI on the function
subpalette Data Acquisition»Signal Conditioning. Using this VI, you
wire the SCXI-1520 analog input reading to VSG, the initial analog input
reading with the system unstrained to Vinit, and the excitation voltage
to VEX.
If you are measuring strain, you can use the strain virtual channel in
Traditional NI-DAQ (Legacy) to perform offset null compensation, shunt
calibration, and to properly scale strain measurements. If you are
measuring any other kind of bridge sensor such as load cell, pressure
sensor, or torque sensor, and the measurement must be displayed in units
of interest for the sensor, you cannot use the strain virtual channel. This
is because the scaling provided by the strain virtual channel returns
measurements in units of microstrain (με) rather than the units of interest
for the sensor. If you require alternative scaling, you can either use an
analog input voltage virtual channel with a custom scale configured in
MAX or SCXI channel strings, and provide scaling in your LabVIEW
application.
© National Instruments Corporation
5-27
SCXI-1520 User Manual
Chapter 5
Using the SCXI-1520
If you are using SCXI channel strings, you can easily convert the
SCXI-1520 voltage signal measurements in your application into scaled
units of interest such as strain, pounds, or newtons. LabVIEW has some
common conversion scaling functions such as the Convert Strain Gauge
Reading VI in the function subpalette Data Acquisition»Analog Input»
Signal Conditioning.
You also can use an Expression Node or Formula Node to convert voltage
signal measurements into whatever units your application requires. You can
find an Expression Node in the function subpalette Numeric. You can find
Formula Nodes in the Function subpalettes Analyze»Mathematics»
Formula. For more information about using the Expression Node or
Formula Node, refer to the LabVIEW User Manual. You also can use the
LabVIEW Help for more detailed information about how to use these nodes
to perform mathematical calculations such as scaling conversions.
Analyze and Display Using Traditional NI-DAQ (Legacy) in LabVIEW
In LabVIEW, you can easily analyze SCXI-1520 measurements with a
variety of powerful analysis functions that you can find in the function
subpalettes Analyze»Waveform Conditioning and Analyze»Signal
Processing. You can perform post acquisition processing such as
waveform comparisons, harmonic analysis, and digital filtering. For more
information about these VIs, refer to the LabVIEW Analysis Concepts
manual. You also can use the LabVIEW Help for more detailed information
about how to use the analysis VIs.
In LabVIEW, you also can easily display SCXI-1520 measurements with a
variety of graphical waveform graphs, numeric slides, gauges, and other
indicators. You can find useful graphical controls and indicators for user
interaction with your application in the controls subpalettes. For more
information about these VIs, refer to the LabVIEW User Manual. You also
can use the LabVIEW Help for more detailed information about how to use
graphical controls and indicators in your application.
Traditional NI-DAQ (Legacy) in Text-Based ADEs
NI text-based ADEs, such as LabWindows/CVI, Measurement Studio for
Microsoft Visual Basic, and Measurement Studio for Microsoft Visual
C++, offer help in the development of test and measurement applications.
These ADEs provide easy data acquisition, data analysis, graphical display,
and data logging tools. Refer to the ADE user manual for more information
about how to use these features.
SCXI-1520 User Manual
5-28
ni.com
Chapter 5
Using the SCXI-1520
The high-level data acquisition tools provided in LabWindows/CVI and
Measurement Studio allow you to easily use virtual channels configured
in MAX, providing easy configuration and programming of the data
acquisition systems. However, some of the more advanced features of the
SCXI-1520 are not accessible through this easy-to-use API. For more
advanced features or for more explicit control of the programmatic
attributes, use the low-level DAQ functions provided in the Traditional
NI-DAQ (Legacy) C API. Refer to the ADE user documentation for more
information about how to use the high-level data acquisition tools that are
provided in your NI ADE.
For more advanced SCXI-1520 applications, or if you are using an ADE
other than an NI ADE, you can use the Traditional NI-DAQ (Legacy) C API
to call functions from the DAQ driver dynamically linked library (dll). The
Low-Level DAQ Functions section outlines the steps for programming with
the low-level DAQ function calls. If you are using LabWindows/CVI or
Measurement Studio, you also can write advanced applications using the
same low-level DAQ functions guidelines.
Low-Level DAQ Functions
Notes If you are a new SCXI-1520 user, NI recommends that you use the NI-DAQmx API
rather than the Traditional NI-DAQ (Legacy) C API. NI-DAQmx is the second generation
data acquisition driver optimized for ease of use and improved performance.
You can find a complete example using Traditional NI-DAQ (Legacy) C API functions to
perform an offset null compensation and shunt calibration with the SCXI-1520 at ni.com/
info using the code rdscaq. Use this example program as a guide when developing your
Traditional NI-DAQ (Legacy) C API application.
You can design your SCXI-1520 application using a typical offset null
compensation and offset null program flow shown in Figure 5-5, which has
the following basic steps:
1.
Configure the system settings for the offset null compensation
operation.
2.
Perform offset null compensation.
3.
Configure settings for the shunt calibration operation.
4.
Perform shunt calibration.
5.
Configure the settings for acquisition.
6.
Perform the acquisition.
7.
Convert the scaling.
© National Instruments Corporation
5-29
SCXI-1520 User Manual
Chapter 5
Using the SCXI-1520
8.
Analyze and display the data.
9.
Clear the acquisition.
Reset Hardware
Perform
Offset Null?
Yes
No
Configure
Acquisition Settings
Perform Offset Null
Compensation
No
Perform Shunt Yes
Calibration?
Configure
Module Settings
Configure
Acquisition Settings
Configure
Module Settings
Acquire and Calculate
Gain Adjust Factor
Perform
Acquisition?
Configure
Acquisition Settings
Yes
Acquire
Continue
Sampling?
Engage
Shunts
Configure
Module Settings
Yes
No
Analyze
Present
Clear and Complete
Acquisition
Figure 5-5. Offset Null and Shunt Calibration Flowchart
SCXI-1520 User Manual
5-30
ni.com
Chapter 5
Using the SCXI-1520
Configuring System Settings Using Traditional NI-DAQ (Legacy) C API
Start the configuration of the acquisition by ensuring that the SCXI-1520
module and SCXI chassis are in their default states, and that the driver
software configuration matches the states the actual physical hardware
configuration. After setting the hardware and software to the defaults of the
module(s), you can configure any module settings that vary from the
default configuration settings. You also should configure the acquisition
parameters using the functions in Table 5-5. For additional information
such as the function prototypes, parameters, and usage instructions for each
function, refer to the Traditional NI-DAQ Function Reference Help
installed by default in Start»Programs»National Instruments»NI-DAQ.
Table 5-5. Configuration Functions
Function
SCXI_Reset
Description
Resets the hardware such as the specified module to its default state.
You also can use SCXI_Reset to reset the SCXI chassis Slot 0
scanning circuitry or reset the entire chassis.
The SCXI-1520 default conditions are:
•
Channels configured for full-bridge connection
•
Gain set at 1.0
•
10 Hz lowpass filter
•
Excitation set at 0 volts
•
Shunt switches disabled
•
Potentiometers mid-ranged
SCXI_Load_Config
Loads the SCXI chassis configuration information you established
in MAX. Sets the software states of the chassis and the modules
present to their default states. This function makes no changes to the
hardware state of the SCXI chassis or modules. It is possible to
programmatically change the configuration you established in
MAX using the SCXI_Set_Config function.
SCXI_Track_Hold_Setup
Establishes the T/H behavior of an SS/H module and sets up the
module for either a single-channel operation or an interval-scanning
operation.
© National Instruments Corporation
5-31
SCXI-1520 User Manual
Chapter 5
Using the SCXI-1520
Table 5-5. Configuration Functions (Continued)
Function
Description
SCXI_SCAN_Setup
Initializes multiplexing circuitry for a scanned data acquisition
operation. Initialization includes storing a table of the channel
sequence and gain setting for each channel to be digitized (MIO and
AI devices only). You cannot repeat channels or use nonsequential
channels when using the SCXI_SCAN_Setup function.
SCXI_MuxCtr_Setup
Programs the E Series DAQ device with the correct number of
channels multiplexed per scan. This number must match the total
number of channels programmed in SCXI_SCAN_Setup.
NI strongly recommends monitoring the built-in error status of each NI-DAQ
function. The NI-DAQ C API provides the NIDAQErrorHandler function, which ensures
that a specified NI-DAQ function executed properly, and assists in handling error messages
and reporting.
Note
Configuring Module Settings Using Traditional NI-DAQ (Legacy) C API
After configuring the hardware for acquisition, you must load the various
channel attributes such as filter, gain, bridge configuration, and excitation
appropriate for your application explicitly using the NI-DAQ function calls
shown in Table 5-6. For more information regarding each setting, refer to
the Traditional NI-DAQ Function Reference Help installed by default in
Start»Programs»National Instruments»NI-DAQ.
SCXI-1520 User Manual
5-32
ni.com
Chapter 5
Using the SCXI-1520
Table 5-6. NI-DAQ Functions Used to Configure SCXI-1520
Channel
Setting
Significant
Parameters
NI-DAQ Function to Use
Possible
Parameters Values
Gain
SCXI_Set_Gain
f64 gain
(gain setting)
1, 1.15, 1.3, 1.5, 1.8,
2, 2.2, 2.4, 2.7, 3.1,
3.6, 4.2, 5.6, 6.5, 7.5,
8.7, 10, 11.5, 13, 15,
18, 20, 22, 24, 27,
31, 36, 42, 56, 65,
75, 87, 100, 115,
130, 150, 180, 200,
220, 240, 270, 310,
360, 420, 560, 650,
750, 870, 1000
Bandwidth
SCXI_Configure_Filter
i16 filterMode
(filter configuration
mode)
0—Bypass the filter
1—Set filter cutoff
frequency to freq
f64 freq
(filter cutoff
frequency if
filterMode = 1)
10.0, 100.0, 1000.0,
10,000.0 Hz
i16
2—DC voltage
specified in units of
volts
Excitation
Voltage
SCXI_Set_Excitation
excitationType
(type of excitation
to set)
f32
excitationValue
(new value for the
specified excitation
parameter)
© National Instruments Corporation
5-33
0, 0.625, 1.25, 1.875,
2.5, 3.125, 3.75,
4.375, 5.0, 5.625,
6.25, 6.875, 7.5,
8.125, 8.75, 9.375,
10.0
SCXI-1520 User Manual
Chapter 5
Using the SCXI-1520
Table 5-6. NI-DAQ Functions Used to Configure SCXI-1520 (Continued)
Channel
Setting
Bridge
Configuration
Significant
Parameters
NI-DAQ Function to Use
SCXI_Configure_Connection
i16
connectionType
(type of sensor
connected to the
specified channel)
Shunt
Calibration
i16 CalOp
(calibration
operation to be
performed)
SCXI_Calibrate_Setup
Possible
Parameters Values
4—Quarter bridge
5—Half bridge
6—Full bridge
0—turn off shunts
4—turn on shunt A
on all channels
5—turn on shunt B
on all channels
Performing Offset Null Compensation Using Traditional NI-DAQ
(Legacy) C API
After configuring the system settings and module properties, you
can perform an offset null compensation programmatically using
SCXI_Strain_Null. This function takes measurements and adjusts the
coarse and fine offset null potentiometers to minimize or eliminate any
electrical offset for a channel. You can repeat this process for each channel
by calling the SCXI_Strain_Null function in a loop. You can use the
resulting imbalance in your application as a software correction factor by
determining the residual voltage from the imbalance, and subtracting this
residual offset from each future measurement. For more information
regarding the operation of SCXI_Strain_Null, refer to the Traditional
NI-DAQ Function Reference Help installed by default in Start»
Programs»National Instruments»NI-DAQ.
Performing Shunt Calibration Using Traditional NI-DAQ (Legacy) C API
After performing an offset null compensation, you can perform a shunt
calibration programmatically. This process is described in the Shunt
Calibration section of Chapter 4, Theory of Operation. You can use
SCXI_Calibrate_Setup with the parameter CalOp set to 4 to engage
SCA, set to 5 to engage SCB, and set to 0 to disengage the shunt resistor of
both switches. After you engage a shunt resistor across an element of the
bridge sensor, wait until the voltage settles, then take a buffer of samples
and average them. Determine what the resultant voltage offset should be.
Calculate a gain adjust factor by dividing the ideal or simulated output by
the measured output and then use the gain adjust factor by multiplying each
SCXI-1520 User Manual
5-34
ni.com
Chapter 5
Using the SCXI-1520
future measurement by the gain adjust factor. Remember to disengage the
shunt switches before continuing your application. For more information
regarding the operation of SCXI_Calibrate_Setup, refer to the
Traditional NI-DAQ Function Reference Help installed by default
in Start»Programs»National Instruments»NI-DAQ.
Performing Acquisition Using Traditional NI-DAQ (Legacy) C API
There are several NI-DAQ functions you can use to take measurements.
Usually in SCXI the preference is to take multiple samples from multiple
channels using the SCAN_Op function. SCAN_Op performs a synchronous,
multiple-channel scanned data acquisition operation. SCAN_Op does not
return until Traditional NI-DAQ (Legacy) acquires all the data or an
acquisition error occurs (MIO, AI, and DSA devices only). For this reason,
it is sometimes useful to use SCAN_Op in conjunction with the function
Timeout_Config, which establishes a timeout limit synchronous
functions to ensure that these functions eventually return control to your
application. After acquiring data using SCAN_Op, the resultant data is not
organized by channel, so you should demultiplex the data using
SCAN_Demux. SCAN_Demux rearranges, or demultiplexes, data acquired by
a SCAN_Op into row-major order, meaning each row of the array holding
the data corresponds to a scanned channel for easier access by C
applications. BASIC applications need not call SCAN_Demux to rearrange
two-dimensional arrays since these arrays are accessed in column-major
order. For more information regarding each acquisition function, refer to
the Traditional NI-DAQ Function Reference Help installed by default in
Start»Programs»National Instruments»NI-DAQ.
Performing Scaling, Analysis, and Display
After acquiring raw voltage data from the acquisition functions, most
applications require adjustment by device calibration constants for
accuracy, scaling measured voltage, analysis, and graphical display.
The SCXI-1520 has stored software calibration constants loaded on
the module EEPROM that are used to achieve the absolute accuracy
specifications. SCXI_Scale scales an array of binary data acquired from
an SCXI channel to voltage using the stored software calibration constants
when it scales the data. You must call SCAN_Demux before SCXI_Scale if
you have multiple channels in the scan. For more information regarding
SCXI_Scale, refer to the Traditional NI-DAQ Function Reference Help
installed by default in Start»Programs»National Instruments»NI-DAQ.
© National Instruments Corporation
5-35
SCXI-1520 User Manual
Chapter 5
Using the SCXI-1520
After you have adjusted the measurement by the appropriate calibration
constants using SCXI_Scale, you can use a function from the NI
conversion library convert.h to convert a voltage or voltage buffer from
a strain gauge to units of strain. NI-ADEs also provide many powerful
analysis functions to perform digital filtering, harmonic analysis,
averaging, and complex mathematics on measurements.
After performing scaling and analysis on the acquired data, you can display
the measurements in several ways. You can use any built-in GUI tools in
your ADE. NI ADEs provide many graphical controls and indicators such
as charts, graphs, gauges, slides, and plots that you can use to display
the data. There is also a built-in function, found in nidaqex.h, called
NIDAQPlotWaveform, that you can use to generate a simple plot of
the data.
Other Application Documentation and Material
Refer to the ADE manual and the DAQ analog input examples that
come with your application software for more detailed information on
programming the SCXI modules for scanning in multiplexed mode.
Traditional NI-DAQ (Legacy) CVI Examples
Many example programs ship with NI-DAQ. For more example
information on how to create tasks and channels, refer to the example
programs. By default, the example programs are installed in C:\Program
Files\NationalInstruments\CVI 7.0\Samples. More examples
are installed by default in C:\Program Files\National
Instruments\NI-DAQ\Examples.
Traditional NI-DAQ (Legacy) Measurement Studio Examples
Many example programs ship with NI-DAQ. For more example
information on how to create tasks and channels, refer to the example
programs. By default, the example programs are installed in C:\Program
Files\NationalInstruments\Measurement Studio 7.0. More
examples are installed by default in C:\Program Files\National
Instruments\NI-DAQ\Examples.
SCXI-1520 User Manual
5-36
ni.com
Chapter 5
Using the SCXI-1520
Calibrating the Strain System
There are two types of calibration important to verifying the accuracy of a
strain measurement system. Device calibration ensures the accuracy of the
SCXI-1520. System calibration involves removing potential error-causing
variables such as offset and verifying the accuracy of the strain element
through shunt calibration.
Calibrating the SCXI-1520
The SCXI-1520 is shipped with a calibration certificate and is calibrated at
the factory to the specifications described in Appendix A, Specifications.
Calibration constants are stored inside the calibration EEPROM and
provide software correction values your application development software
uses to correct the measurements for offset errors in the module.
To obtain the highest level of accuracy, you should periodically perform
an internal calibration. You can initiate an internal calibration using
NI software.
For more information on calibrating the SCXI-1520, download the
SCXI-1520 Calibration Procedure from ni.com/calibration.
Internal Calibration Procedure
The SCXI-1520 incorporates internal calibration paths that allow routing
channel inputs to ground or to an onboard reference voltage. NI software
disconnects the channel inputs from the front signal connector and
reconnects the inputs to ground or to an onboard reference when
performing an internal calibration. You need not change any input
connections for an internal calibration.
© National Instruments Corporation
5-37
SCXI-1520 User Manual
Chapter 5
Using the SCXI-1520
Internal Calibration Using LabVIEW
NI recommends that you internally calibrate the DAQ device before you internally
calibrate the SCXI-1520.
Note
For internal calibration using LabVIEW, complete the following
steps using the LabVIEW SCXI Calibrate VI found in LabVIEW at
NI Measurements»Data Acquisition»Calibration and Configuration:
1.
Enter the DAQ device and the SCXI channel string for the channel you
want to calibrate.
2.
Select internal calibration as the calibration operation you are going
to perform.
The driver software takes a few seconds to perform the calibration. After
completion, the module has new calibration constants stored for all gain
settings. You must repeat the procedure to calibrate other channels in the
module.
Internal Calibration Using a C-Based ADE
For internal calibration using a C-based ADE, complete the following steps
using the NI-DAQ function, SCXI_Calibrate:
1.
Enter the DAQ device, DAQ channel, module slot, and module
channel.
2.
Select internal calibration (0) as the operation you are going to
perform.
The SCXI-1520 takes a few seconds to perform the calibration. After
completion, the module has new calibration constants stored for all gain
settings. You must repeat the procedure to calibrate other channels in the
module.
External Calibration
For instructions on how to perform an external calibration on the
SCXI-1520, refer to the SCXI-1520 Calibration Procedure available by
going to ni.com/calibration and clicking Manual Calibration
Procedures. NI recommends you perform an external calibration once
a year.
SCXI-1520 User Manual
5-38
ni.com
Chapter 5
Using the SCXI-1520
Calibrating the System
You should perform offset null compensation or shunt calibration on
transducers in the system to improve accuracy. This is considered system,
or end-to-end, calibration.
Offset Null Compensation
Performing an offset null compensation removes offset in the measurement
system. Factors such as imperfections in the strain gauge, electrical offset
in the measurement system, signal leads with significant lead resistance,
as well as other system variables can create offset. Refer to the Offset Null
Compensation section of Chapter 4, Theory of Operation, for information
about how to perform offset null compensation.
Shunt Calibration
Performing shunt calibration removes gain or amplitude errors in the
measurement system. Factors such as non-ideal gauges, incorrect strain
gauge factor, temperature fluctuations, as well as other system variables
can create these errors. Refer to the Shunt Calibration section of Chapter 4,
Theory of Operation, for information about how to perform shunt
calibration.
© National Instruments Corporation
5-39
SCXI-1520 User Manual
A
Specifications
This appendix lists the specifications for the SCXI-1520 modules. These
specifications are typical at 25 °C unless otherwise noted.
Analog Input
Number of channels ............................... 8
Voltage gain settings.............................. X1 to X1000 with the following
gain settings: 1; 1.15; 1.3; 1.5;
1.8; 2; 2.2; 2.4; 2.7; 3.1; 3.6; 4.2;
5.6; 6.5; 7.5; 8.7; 10; 11.5; 13; 15;
18; 20; 22; 24; 27; 31; 36; 42; 56;
65; 75; 87; 100; 115; 130; 150;
180; 200; 220; 240; 270; 310;
360; 420; 560; 650; 750; 870;
1000
Input coupling ........................................ DC
Overvoltage protection........................... ±35 V powered on,
±25 V powered off
Inputs protected...................................... <0..7>
Transfer
Nonlinearity ........................................... Better than 0.02% of FSR
Gain error ............................................... ±0.35% of setting at RSC,
±0.1% of the value returned
by driver software
Offset error
Gain ≥20 ......................................... 150 μV max
Gain <20 ......................................... 3 mV max
© National Instruments Corporation
A-1
SCXI-1520 User Manual
SCXI-1520 User Manual
A-2
±0.1
±0.1
±0.1
±0.1
±0.1
±0.1
±0.1
±0.1
±0.1
±0.1
Percent of
Reading†
50.0 μV
20.0 μV
20.0 μV
±50.0 μV
±50.0 μV
±50.0 μV
0.2 mV
±75.0 μV
100.0 μV
0.5 mV
±150.0 μV
±50.0 μV
1.0 mV
2.0 mV
5.0 mV
10.0 mV
Single Point
±0.3 mV
±0.5 mV
±1.5 mV
±3.0 mV
Offset†
2.0 μV
2.0 μV
5.0 μV
10.0 μV
20.0 μV
50.0 μV
0.1 mV
0.2 mV
0.5 mV
1.0 mV
100-Point
Average
System Noise
(Peak, 3 Sigma)†
±5
±5
±5
±5
±5
±5
±25
±25
±25
±25
To include the effects of temperature drift outside the range 15 to 35 °C, add the term, T × (Gain Drift) × (Range) × T × (Offset Drift),
where T is temperature difference between the module temperature and 15 or 35 °C, whichever is smaller. Bandwidth setting is 10 Hz and scan rate for 100-point
averages is 200 scans/s. Excitation is set to 0 V. To calculate the absolute accuracy for the SCXI-1520, visit ni.com/accuracy.
±0.03
±0.03
±0.03
±0.03
±0.03
±0.03
±0.03
±0.03
±0.03
±0.03
Offset
(μV/°C)
Temperature Drift
Gain Drift
(%/°C)
† Absolute accuracy (15 to 35 °C). Absolute accuracy is (Voltage Reading) × (% of Reading) + (Offset Error) + (System Noise).
1000.0
±10.0 mV
42.0
±180.0 mV
420.0
20.0
±500.0 mV
±18.0 mV
10.0
±1.0 V
200.0
4.2
±1.8 V
±50.0 mV
2.0
±5.0 V
100.0
1.0
±10.0 V
±100.0 mV
Overall
Gain†
Nominal
Range†
Complete Accuracy Table, Voltage
Appendix A
Specifications
ni.com
© National Instruments Corporation
100
560
1000
1000
1000
±40000 με
±7000 με
±4000 με
±2500 με
±1250 με
Quarter-Bridge
Half-Bridge
Full-Bridge
±0.1
±0.1
±0.1
±0.1
±0.1
±20000 με
±40000 με
±80000 με
±80000 με
±80000 με
Hardware
Nulling
Range
±1 με
±2 με
±4 με
±7 με
±40 με
Single
Point
±0.2 με
±0.5 με
±1 με
±2 με
±4 με
100-Point
Average
±0.03
±0.03
±0.03
±0.03
±0.03
Gain
Drift
(%/°C)
±2
±4
±8
±16
±80
Offset
(με/°C)
Temperature Drift
To include the effects of temperature drift outside the range 15 to 35 °C, add the term, T × (Gain Drift) × (Range) + T × (Offset Drift),
where T is temperature difference between the module temperature and 15 or 35 °C, whichever is smaller. Bandwidth setting is 10 Hz and scan rate for 100-point
averages is 200 scans/s. To calculate the absolute accuracy for the SCXI-1520, visit ni.com/accuracy.
† Absolute accuracy (15 to 35 °C). Absolute accuracy is (Voltage Reading) × (% of Reading) + (Offset Error) + (System Noise).
Gain
Range
Bridge
Percent of
Reading†
System Noise
(Peak, 3 Sigma)†
Complete Accuracy Table, Strain, GF = 2.0, Excitation = 5 V
Appendix A
A-3
Specifications
SCXI-1520 User Manual
Appendix A
Specifications
Amplifier
Input impedance (DC) ............................ >1 GΩ
Input impedance (DC) powered off........5.8 kΩ min
Input bias current ....................................±20 nA max
Input offset current .................................±20 nA max
CMRR (DC to 60 Hz, full-bridge setting)
Gain ≥20 ..........................................>85 dB
Gain <20 ..........................................>60 dB
Dynamic
Minimum scan interval (per channel, any gain in multiplexed mode)
±0.0125% accuracy .........................3 μs
±0.006% accuracy ...........................10 μs
±0.0015% accuracy .........................20 μs
Noise RTI, gain = 200, 0.1 to 10 Hz.......2.0 μVpp
Spot noise RTI, gain = 200, 1000 Hz .....16 nV/ Hz
Filter
Lowpass filter type .................................4-pole Butterworth
(24 dB/octave rolloff)
Lowpass filter settings ............................10 Hz, 100 Hz, 1 kHz,
10 kHz, or bypass
Bandwidth, filter bypassed .....................–3 dB at 20 kHz
Simultaneous Sample and Hold
Acquisition time
Settle to 0.012%...............................7 μs
Settle to 0.003%...............................10 μs
Settle to 0.0015%.............................50 μs
Hold mode settling time .........................1 μs typ
Interchannel skew ...................................200 ns typ
SCXI-1520 User Manual
A-4
ni.com
Appendix A
Specifications
Intermodule skew ................................... 200 ns typ
Droop rate .............................................. 30 mV/s typ, 100 mV/s max
Stability
Recommended warm-up time ................ 15 minutes
Gain drift ................................................ ±40 ppm of reading/°C max
Offset drift
Gain ≥20 ......................................... ±2 μV/°C typ, ±5 μV/°C max
Gain <20 ......................................... ±10 μV/°C typ, ±25 μV/°C max
Offset Null Compensation
Range ..................................................... ±4% of excitation voltage,
20,000 counts of resolution
(±80,000 με offset null
compensation range, 4 με
resolution for quarter-bridge,
GF = 2.0)
Excitation
Type ....................................................... Constant voltage
Settings................................................... 0.0 to 10.0 V in 0.625 V
increments
Error ....................................................... ±20 mV ±0.3% of nominal setting
±0.1% of value returned by driver
software
Maximum operating current
in all ranges ............................................ 29 mA
Short-circuit protection .......................... Yes
Regulation .............................................. No load to 120 Ω load
With remote sense........................... ±0.003%
Without remote sense...................... ±0.08%
Temperature drift ................................... ±0.005%/°C, ±30 μV/°C max
© National Instruments Corporation
A-5
SCXI-1520 User Manual
Appendix A
Specifications
Noise, DC to 10 kHz...............................200 μVpp
Remote sense ..........................................Error less than ±0.02% per ohm
of lead resistance, both leads
Protection................................................Surge arrestors in parallel with
excitation terminals, shunt to
ground
Bridge Completion
Half-bridge..............................................Two precision resistors,
5 kΩ each, 0.1% ratio matching
Quarter-bridge ........................................Socketed resistor inside the
SCXI-1314 terminal block1
Shunt Calibration
Type ........................................................Two independent points
Resistor ...................................................Socketed inside the SCXI-1314
terminal block2
Switch resistance ....................................32 Ω typ
50 Ω max
Switch off leakage ..................................<1 nA
Switch break-down voltage ....................±60 VDC
Power Consumption
V+ ...........................................................18.5 to 25 VDC, +170 mA max
V– ...........................................................–18.5 to –25 VDC, –170 mA max
+5 V ........................................................+4.75 to 5.25 VDC, 50 mA max
1
2
Half-bridge completion is performed inside the module and configured under software control. The quarter-bridge completion
resistor is in the SCXI-1314 terminal block and is socketed. Resistors shipped with the SCXI-1314 are 120 Ω and
350 Ω (default value) RN-55 style (standard 1/4 W size). The tolerance is ±0.1% and the temperature coefficient is
10 ppm/°C max.
Shunt calibration resistors are in the SCXI-1314 terminal block and are socketed. Resistors shipped with the SCXI-1314
are 100 kΩ RN-55 style (standard 1/8 W size). The tolerance is ±0.1% and the temperature coefficient is 10 ppm/°C max.
SCXI-1520 User Manual
A-6
ni.com
Appendix A
Specifications
Physical
Dimensions............................................. 3.0 × 17.2 × 20.3 cm
(1.2 × 6.9 × 8.0 in.)
Weight .................................................... 750 g (1 lb 10.4 oz)
Maximum Working Voltage
Maximum working voltage refers to the signal voltage plus the
common-mode voltage.
Channel-to-earth..................................... Either the SX+ or SX– input
should remain within ±10 V of
ground. Both inputs should be
within ±10 V of one another,
Measurement Category I
Channel-to-channel ................................ Either the SX+ or SX– input
should remain within ±10 V of
ground. Both inputs should be
within ±10 V of one another,
Measurement Category I
Caution
Do not use for measurements within Categories II, III, or IV.
Environmental
Operating temperature............................ 0 to 50 °C
Storage temperature ............................... –20 to 70 °C
Humidity ................................................ 10 to 90% RH, noncondensing
Maximum altitude .................................. 2,000 m
Pollution Degree (indoor use only) ........ 2
© National Instruments Corporation
A-7
SCXI-1520 User Manual
Appendix A
Specifications
Safety
This product meets the requirements of the following standards of safety
for electrical equipment for measurement, control, and laboratory use:
•
IEC 61010-1, EN 61010-1
•
UL 61010-1, CSA 61010-1
Note For UL and other safety certifications, refer to the product label or the Online
Product Certification section.
Electromagnetic Compatibility
This product meets the requirements of the following EMC standards for
electrical equipment for measurement, control, and laboratory use:
•
EN 61326 (IEC 61326): Class A emissions; Basic immunity
•
EN 55011 (CISPR 11): Group 1, Class A emissions
•
AS/NZS CISPR 11: Group 1, Class A emissions
•
FCC 47 CFR Part 15B: Class A emissions
•
ICES-001: Class A emissions
For the standards applied to assess the EMC of this product, refer to the Online
Product Certification section.
Note
Note
For EMC compliance, operate this device with shielded cabling.
CE Compliance
This product meets the essential requirements of applicable European
Directives as follows:
•
2006/95/EC; Low-Voltage Directive (safety)
•
2004/108/EC; Electromagnetic Compatibility Directive (EMC)
Online Product Certification
Refer to the product Declaration of Conformity (DoC) for additional
regulatory compliance information. To obtain product certifications and
the DoC for this product, visit ni.com/certification, search by model
number or product line, and click the appropriate link in the Certification
column.
SCXI-1520 User Manual
A-8
ni.com
Appendix A
Specifications
Environmental Management
NI is committed to designing and manufacturing products in an
environmentally responsible manner. NI recognizes that eliminating
certain hazardous substances from our products is beneficial to the
environment and to NI customers.
For additional environmental information, refer to the NI and the
Environment Web page at ni.com/environment. This page contains the
environmental regulations and directives with which NI complies, as well
as other environmental information not included in this document.
Waste Electrical and Electronic Equipment (WEEE)
EU Customers At the end of the life cycle, all products must be sent to a WEEE recycling
center. For more information about WEEE recycling centers and National Instruments
WEEE initiatives, visit ni.com/environment/weee.
⬉ᄤֵᙃѻક∵ᶧ᥻ࠊㅵ⧚ࡲ⊩ ˄Ё೑ RoHS˅
Ё೑ᅶ᠋ National Instruments ヺড়Ё೑⬉ᄤֵᙃѻકЁ䰤ࠊՓ⫼ᶤѯ᳝ᆇ⠽䋼ᣛҸ (RoHS)DŽ
݇Ѣ National Instruments Ё೑ RoHS ড়㾘ᗻֵᙃˈ䇋ⱏᔩ ni.com/environment/rohs_chinaDŽ
(For information about China RoHS compliance, go to ni.com/environment/rohs_china.)
© National Instruments Corporation
A-9
SCXI-1520 User Manual
Using SCXI Channel Strings with
Traditional NI-DAQ (Legacy) 7.0
or Later
B
This appendix is not applicable if you use the virtual channels to configure and
measure the SCXI channels. Virtual channels are configured using MAX. If you use virtual
channels, you address the SCXI channels by specifying the channel name(s) in the channel
string input.
Note
When using LabVIEW, Measure, and Visual Basic, the SCXI channel
string determines which SCXI channels are scanned and the scanning
sequence. The SCXI channel string allows you to take measurements from
several channels on one module with only one channel string entry. An
array of these channel string entries configures multiple modules for
scanning. When the application program runs, the channel string is used
for programming the channel information into the SCXI system.
The format of the channel string is as follows:
obx ! scy ! mdz ! channels
where
obx is the onboard E Series DAQ device channel, with x representing
a particular channel where the multiplexed channels are sent. This
value is 0 for DAQ device channel 0 in a single-chassis system. In a
multichassis or remote chassis system, the DAQ device channel x
corresponds to chassis number n – 1, where DAQ device channel x is
used for scanning the nth chassis in the system.
scy is the SCXI chassis ID, where y is the number you chose when
configuring the chassis.
mdz is the slot position where the module is located, with z being the
particular slot number. The slots in a chassis are numbered from left to
right starting with 1.
© National Instruments Corporation
B-1
SCXI-1520 User Manual
Appendix B
Using SCXI Channel Strings with Traditional NI-DAQ (Legacy) 7.0 or Later
channels is the list of channels that are scanned for module z. It can
have several formats:
•
obx ! scy ! mdz ! nx, where nx is a single input channel.
•
obx ! scy ! mdz ! (n0, n2), where n0, n2 are individual
input channels that are not necessarily sequential.
•
obx ! scy ! mdz ! n0:n3, where n0 and n3 represent an
ascending sequential list of input channels, inclusive.
•
obx ! scy ! mdz ! (n0, n2, n3:n4, n1, n5, n2), where
n0, n2, and n5 represent single channels, not necessarily
sequential, and n3 and n4 represent the endpoints of an ascending
sequential list of channels, inclusive. In this case, channels n1 and
n2 are explicitly repeated in the channel list.
Notes Using parentheses surrounding multiple channels in a channel string is important
for correct scanning operation of the SCXI channels.
In a single-chassis system, the obx ! specifier is optional and causes the gains on the
module and E Series DAQ device to be automatically set to fit the input limits parameter.
When this specifier is omitted, the default gain on the DAQ device, usually the lowest gain,
is used, but the SCXI-1520 gain is adjusted to fit the input limits. NI recommends using the
obx ! specifier.
Repeating channels or having channels out of sequence in a scan list is not supported on
all SCXI modules. Refer to the manual of each module for information on this feature,
which is referred to as flexible scanning or random scanning.
For more information about using SCXI channel string, refer to the
LabVIEW Measurements Manual and SCXI-1520 shipping examples.
Special SCXI-1520 Channel Strings
There are two special channel strings you can use with the SCXI-1520 to
acquire signals from alternative locations rather than the signal inputs on
the channels: the remote-sense and calibration ground channel strings. This
section describes the use of these channels.
SCXI-1520 User Manual
B-2
ni.com
Appendix B
Using SCXI Channel Strings with Traditional NI-DAQ (Legacy) 7.0 or Later
Remote-Sense Channel String
You can scan the remote-sense terminals to monitor the excitation voltage
while simultaneously acquiring data from analog input channels. This is
useful for scaling the measurements by exactly the excitation voltage that
is applied to the bridge sensor. To scan the positive remote-sense terminal
of the nth channel, use the channel string obx ! scy ! mdz ! p_pos(n)
To scan the negative remote-sense terminal of the nth channel, use the
channel string obx ! scy ! mdz ! p_neg(n)
To measure the total excitation voltage across the bridge, you must take the
difference between p_pos(n) and p_neg(n).
Note
(nth channel bridge excitation voltage) = (reading from p_pos(n)) –
(reading from p_neg(n))
Note If no wires are connected to the remote-sense terminals RS+ and RS–, the voltages
measured are the voltages on excitation output terminals P+ and P–. Internal 1 kΩ resistors
connect RS+ to P+ and RS– to P–.
Calibration Ground Channel String
The SCXI-1520 has a special calibration feature that enables LabVIEW to
ground the module amplifier inputs so that you can read the amplifier
offset. For the other SCXI analog input modules, you must physically wire
the terminals to ground. The measured amplifier offset is for the entire
signal path including the SCXI module and the E Series DAQ device.
To read the grounded amplifier on the SCXI-1520 use the standard SCXI
string syntax in the channels array with calgndz substituted for the
channel number, where z is the appropriate SCXI channel needing
grounding.
For example, use the SCXI channel string ob0 ! sc1 ! md1 ! calgnd0
to read the grounded channel 0 signal of the module in Slot 1 of SCXI
chassis 1. The resulting measurement should be very close to 0 V. The AI
Start VI grounds the amplifier before starting the acquisition. The AI Clear
VI removes the grounds from the amplifier after the acquisition completes.
You can specify a range of channels also. The string calgnd0:7 grounds
the amplifier inputs for channels 0 through 7 and reads the offset for each
amplifier.
© National Instruments Corporation
B-3
SCXI-1520 User Manual
Appendix B
Using SCXI Channel Strings with Traditional NI-DAQ (Legacy) 7.0 or Later
Use the SCXI Calibrate VI, available on the Functions»Data Acquisition»
Calibration and Configuration palette, to automatically perform a self
calibration and modify the scaling constants on the module to adjust for any
amplifier offset. Refer to the Calibrating the Strain System section of
Chapter 5, Using the SCXI-1520, for more information about how to use
SCXI Calibrate VI with the SCXI-1520.
SCXI-1520 User Manual
B-4
ni.com
Removing the SCXI-1520
C
This appendix explains how to remove the SCXI-1520 from MAX and an
SCXI chassis.
Removing the SCXI-1520 from MAX
To remove a module from MAX, complete the following steps after
launching MAX:
1.
Expand Devices and Interfaces.
2.
Expand the list of installed chassis by clicking the + next to
NI-DAQmx and/or Traditional NI-DAQ Devices.
3.
Expand the list of installed modules by clicking the + next to the
appropriate chassis.
4.
Right-click the module or chassis you want to delete and click Delete.
5.
A confirmation window opens. Click Yes to continue deleting the
module or chassis or No to cancel this action.
Deleting the SCXI chassis deletes all modules in the chassis. All configuration
information for these modules is also lost.
Note
The SCXI chassis and/or SCXI module(s) should now be removed from the
list of installed devices in MAX.
Removing the SCXI-1520 from a Chassis
Consult the documentation for the chassis and accessories for additional
instructions and precautions. To remove the SCXI-1520 module from a
chassis, complete the following steps while referring to Figure C-1:
Note Figure C-1 shows an SCXI chassis, but the same steps are applicable to a PXI/SCXI
combination chassis.
1.
Power off the chassis. Do not remove the SCXI-1520 module from a
chassis that is powered on.
2.
If the SCXI-1520 is the module cabled to the E/M Series DAQ device,
disconnect the cable.
© National Instruments Corporation
C-1
SCXI-1520 User Manual
Appendix C
Removing the SCXI-1520
3.
Remove any terminal block that connects to the SCXI-1520.
4.
Rotate the thumbscrews that secure the SCXI-1520 to the chassis
counterclockwise until they are loose, but do not completely remove
the thumbscrews.
Remove the SCXI-1520 by pulling steadily on both thumbscrews until the
module slides completely out.
7
6
1
5
4
3
2
1
5
ADDRESS
ョ
SC
MA
XI
INF
RA
ME
SC
XI
11
00
4
2
3
1
2
3
4
Cable
SCXI Module Thumbscrews
SCXI-1520
Strain-Gauge or Wheatstone-Bridge Based Transducer
5
6
7
Terminal Block
SCXI Chassis Power Switch
SCXI Chassis
Figure C-1. Removing the SCXI-1520
SCXI-1520 User Manual
C-2
ni.com
D
Common Questions
This appendix lists common questions related to the use of the SCXI-1520.
Which version of NI-DAQ works with the SCXI-1520, and how do I get
the most current version of NI-DAQ?
You must have NI-DAQ 7.0 or later. Visit the NI Web site at ni.com and
select Download Software»Drivers and Updates»Search Drivers and
Updates. Enter the keyword NI-DAQ to find the latest version of NI-DAQ
for your operating system.
I have gone over the Verifying and Self-Testing the Installation section of
Chapter 1, About the SCXI-1520, yet I still cannot correctly test and
verify that my SCXI-1520 is working. What should I do now?
Unfortunately, there is always the chance that one or more components in
the system are not operating correctly. You may have to call or email a
technical support representative. The technical support representative often
suggests additional troubleshooting measures. If requesting technical
support by phone, have the system nearby so you can try these measures
immediately. NI contact information is listed in the Technical Support
Information document.
In NI-DAQmx, can I use channels of different measurement types in
the same task?
Yes, you can set up your channels programmatically or through the DAQ
Assistant.
Will MAX allow me to configure two SCXI-1520 modules that are
in the same chassis, in multiplexed mode, with two different
E/M Series DAQ devices?
No.
© National Instruments Corporation
D-1
SCXI-1520 User Manual
Appendix D
Common Questions
If the SCXI-1520 module is not cabled directly to a E/M Series DAQ
device, can I measure conditioned signals for channels 0 through 7
at the rear connector, for example using a scope, DMM, or custom
acquisition system?
NI does not support or recommend this usage. In multiplexed mode
simultaneous sample and hold would cause glitches in the scope and would
likely average glitches in the DMM, giving inaccurate measurements.
Can I use the unused analog input channels of the E/M Series DAQ
device if I am directly cabled to the SCXI-1520, for example with the
SCXI-1180 feedthrough?
No. E/M Series DAQ device channels 1 through 7 connect to the
conditioned analog outputs of SCXI-1520 channels 1 through 7.
Can I configure the SCXI-1520 for use in parallel mode?
You can configure the SCXI-1520 for parallel mode using NI-DAQmx.
Refer to Chapter 4, Theory of Operation, for more information.
You cannot configure the SCXI-1520 for parallel mode using Traditional
NI-DAQ (Legacy).
Which digital lines are unavailable on the E/M Series DAQ device if it
is cabled to an SCXI-1520 module?
Table D-1 shows the digital lines that are used by the SCXI-1520 for
communication and scanning. These lines are unavailable for
general-purpose digital I/O if the SCXI-1520 is connected to the
E/M Series DAQ device.
Table D-1. Digital Signals on the SCXI-1520
E/M Series
DAQ Device
Signal Name
NI-DAQmx SCXI
Signal Name
Traditional
NI-DAQ (Legacy)
SCXI Signal Name
50-Pin
Connector
68-Pin
Connector
Direction†
DIO0
P0.0
SER DAT IN
25
52
Output
DIO4
P0.4
SER DAT OUT
26
19
Input
DIO1
P0.1
DAQ D*/A
27
17
Output
DIO2
P0.2
SLOT0SEL*
29
49
Output
SCANCLK
AI HOLD COMP,
AI HOLD
SCAN CLK
36
46
Output
SCXI-1520 User Manual
D-2
ni.com
Appendix D
Common Questions
Table D-1. Digital Signals on the SCXI-1520 (Continued)
E/M Series
DAQ Device
Signal Name
NI-DAQmx SCXI
Signal Name
Traditional
NI-DAQ (Legacy)
SCXI Signal Name
50-Pin
Connector
68-Pin
Connector
Direction†
PFI 7/ AI SAMP
CLK
PFI 7/
AI SAMP CLK,
AI SAMP
HOLD TRIG
46
38
Input
EXTSTROBE*
EXTSTROBE*
SER CLK
37
45
Input
† With respect to the E/M Series DAQ device.
In LabVIEW, can I use different input limits for the same SCXI-1520
channel if I repeat the channel in the SCXI channel string array?
No. The SCXI-1520 cannot dynamically change the gain settings during
scanning. Therefore, group channels with similar input ranges together in
the channel string array. Make sure that repeated channels in different
indices of the channel string array have the same input limits in the
corresponding input limits array.
In LabVIEW, can I use a VI to change my SCXI-1520 configuration
settings?
Yes. You can use the AI Parameter VI to change all the SCXI-1520
configuration settings. You also can change the configuration settings in
NI-DAQmx using NI-DAQmx Tasks. Refer to Chapter 5, Using the
SCXI-1520, for more information.
Some SCXI modules permit flexible scanning. Does the SCXI-1520
module permit flexible scanning?
Yes. Flexible scanning is described in Chapter 3, Configuring and Testing,
but you cannot use flexible scanning when you are using C and Traditional
NI-DAQ (Legacy). When using C, you can scan only consecutive channels
using traditional SCXI channel programming. Refer to the NI-DAQ
Function Reference Help for more details on SCXI scanning.
Are there any cabling restrictions when using an SCXI-1520 module
with a plug-in E/M Series DAQ device?
Yes. If a chassis contains an SCXI-1520, SCXI-1530/1531, or SCXI-1140
module, at least one of these modules must be the cabled module. A cabled
module is the module connected directly to the E/M Series DAQ device.
This ensures that a timing signal is available for use by all
simultaneous-sampling SCXI modules in the chassis.
© National Instruments Corporation
D-3
SCXI-1520 User Manual
Appendix D
Common Questions
Can I use the SCXI-1520 with a version of NI-DAQ that works under
the Macintosh Operating System (Mac OS)?
No, as of NI-DAQ 6.6.1. Check the release notes of later versions of
NI-DAQ at ni.com for updates.
Is a register-level programming manual available for the SCXI-1520?
NI does not support register-level programming for the SCXI-1520.
What is the power-on state of the SCXI-1520 multiplexer, analog bus
switches, and configuration settings?
The multiplexer, analog bus switches, and configuration settings are not
in a known state immediately after power on. All hardware settings are
programmed automatically when beginning an acquisition in LabVIEW
or a test panel in MAX.
Which accessories can I use to connect signals to the front of the
SCXI-1520 module?
Refer to Chapter 1, About the SCXI-1520, for more information.
How do I control the gain, excitation voltage, filter setting, bridge
configuration, potentiometer settings, and shunt calibration switches
from LabVIEW?
The gain of each SCXI-1520 channel is automatically set based on the
channel limits used in setting up the acquisition. You usually use the
LabVIEW AI Config VI to set the channel limits. If the channel limits are
not explicitly set, the SCXI-1520 defaults to the gain setting entered when
the module was configured using MAX. Refer to Chapter 3, Configuring
and Testing, for more information.
Although excitation voltage, filter setting, and bridge configuration are
usually set using MAX, you also can control or change these settings
programmatically using AI Parameter VI in LabVIEW.
Although you usually use the SCXI Strain Null VI to adjust the electronic
potentiometers for offset nulling the analog inputs to zero, you also
can manually set or retrieve the potentiometer settings using the
AI Parameter VI.
The shunt calibration switches are exclusively controlled using the
AI Parameter VI.
SCXI-1520 User Manual
D-4
ni.com
Appendix D
Common Questions
How do I control the gain, excitation voltage, filter setting, bridge
configuration, potentiometer settings, and shunt calibration switches
in C-based application environments?
You must use the NI-DAQ functions listed in Table 5-6, NI-DAQ Functions
Used to Configure SCXI-1520.
For an SCXI-1520 channel to take a voltage measurement from a
sensor that is not in a bridge configuration, are there any special
considerations?
You should set the excitation voltage to zero and the bridge configuration
to full bridge. This is because the SCXI-1520 input offset correction
constants stored in the EEPROM are obtained with the excitation voltage
set to zero. With the excitation voltage not at zero, error voltages from the
auto-nulling circuits can increase offset error beyond the limits given in the
specifications.
What should I take into consideration when I take measurements from
sensors with external excitation?
Set the SCXI-1520 internal excitation to the closest value to match the
external excitation level. If you want to perform offset null compensation,
you must set the excitation level to a value other than zero.
If I am powering my bridge-based transducers with an external
voltage source, what voltage setting should I set on the SCXI-1520?
Use the closest corresponding value allowed by the SCXI-1520.
Do the SCXI-1314 or SCXI-1314T terminal blocks contain a CJC
temperature sensor?
No.
Are there any user-serviceable parts inside the SCXI-1520?
No. There are no fuses, multiturn potentiometers, DIP switches, slide
switches, socketed resistors, or jumpers inside the module. Disassembly of
the module for any reason can void its warranty and nullify its calibration.
Can I use remote sense when powering a Wheatstone-bridge based
transducer with an external source?
No. Remote sense uses a feedback loop and this feedback loop would be
erratic since the SCXI-1520 cannot control the level of the external source.
© National Instruments Corporation
D-5
SCXI-1520 User Manual
Appendix D
Common Questions
How do I perform external triggering using the SCXI-1520?
For analog triggering, use your data acquisition device analog triggering
functionality through pin PFI 0. Verify that your E/M Series DAQ device
supports analog triggering. For more information about analog triggering
with the SCXI-1520, refer to the Analog Hardware Triggering using SCXI
KnowledgeBase by going to ni.com/info and using the info code
rdahtu.
For digital triggering, use your data acquisition device digital triggering
functionality through pin PFI 0. All E/M Series DAQ devices support
digital triggering. For more information about digital triggering with the
SCXI-1520, refer to the DAQ device help file for more information.
Can I measure TEDS load cells with the SCXI-1520?
You can use the SCXI-1314T terminal block to read TEDS load cells. Refer
to ni.com for more information about TEDS sensors and accessories.
SCXI-1520 User Manual
D-6
ni.com
Glossary
Symbol
Prefix
Value
p
pico
10 –12
n
nano
10 –9
μ
micro
10 – 6
m
milli
10 –3
k
kilo
10 3
M
mega
10 6
G
giga
10 9
T
tera
10 12
Numbers/Symbols
%
percent
+
positive of, or plus
–
negative of, or minus
±
plus or minus
<
less than
>
greater than
/
per
°
degree
ε
strain
εs
simulated strain
υ
Poisson’s ratio
© National Instruments Corporation
G-1
SCXI-1520 User Manual
Glossary
Ω
ohms
+5V (signal)
+5 VDC source signal
A
A
Amperes
A/D
Analog-to-Digital
absolute accuracy
The maximum difference between the measured value from a data
acquisition device and the true voltage applied to the input, typically
specified as ± voltage.
AC
Alternating Current
acquisition time
The time required by a sample-and-hold system to switch from hold mode
back to tracking a signal.
ADC
Analog-to-Digital Converter—An electronic device, often an integrated
circuit, that converts an analog voltage to a digital number.
ADE
Application Development Environment, such as LabVIEW,
LabWindows/CVI, Visual Basic, C, and C++.
AI
analog input
AI HOLD
Scan clock signal used to increment to the next channel after each
E/M Series DAQ device analog-to-digital conversion.
AI HOLD COMP
See AI HOLD.
AI SAMP
See HOLD TRIG.
AI SAMP CLK
See HOLD TRIG.
amp
amplifier
amplification
A type of signal conditioning that improves accuracy in the resulting
digitized signal by increasing signal amplitude relative to noise.
ANSI
American National Standards Institute
SCXI-1520 User Manual
G-2
ni.com
Glossary
B
bandwidth
The range of frequencies present in a signal, or the range of frequencies to
which a measuring device can respond.
bias current
The small input current flowing into or out of the input terminals of an
amplifier.
bipolar
A voltage range spanning both negative and positive voltages.
bit
One binary digit, either 0 or 1.
bridge completion
resistors
Fixed-valued resistors used to complete a Wheatstone bridge when fewer
than four of the bridge elements are working strain gauges.
Butterworth filter
A lowpass filter whose characteristics are optimized for maximum flatness
in the passband.
C
C
Celsius
CE
European emissions control standard
CFR
Code of Federal Regulations
CH
channel
channel
Pin or wire lead to which you apply, or from which you read, an analog or
digital signal. Analog signals can be single-ended or differential. For digital
signals, channels are grouped to form ports.
chassis
The enclosure that houses, powers, and controls SCXI modules.
CLK
clock input signal
CMRR
Common-Mode Rejection Ratio—A measure of the ability of a differential
amplifier to reject interference from a common-mode signal, usually
expressed in decibels (dB).
CMV
See common-mode voltage.
common-mode noise
Noise that appears on both inputs of a differential amplifier.
© National Instruments Corporation
G-3
SCXI-1520 User Manual
Glossary
common-mode voltage
Voltage that appears on both inputs of a differential amplifier.
compressive strain
Strain that results from an object being compressed; has a negative value.
current excitation
A source that supplies the current needed by a sensor for its proper
operation.
cutoff frequency
The frequency that defines the upper end of the passband of a lowpass filter.
D
D/A
Digital-to-Analog
D*/A
Data/Address
D GND
See DGND.
DAC
D/A converter—An electronic device, often an integrated circuit, that
converts a digital number into a corresponding analog voltage or current.
DAQ
data acquisition—(1) Collecting and measuring electrical signals from
sensors, transducers, and test probes or fixtures and processing the
measurement data using a computer; (2) Collecting and measuring the
same kinds of electrical signals with A/D and/or DIO boards plugged into
a computer, and possibly generating control signals with D/A and/or DIO
boards in the same computer.
DAQ D*/A
The data acquisition board data/address line signal used to indicate whether
the SER DAT IN pulse train transmitted to the SCXI chassis contains data
or address information.
DAQ device
A data acquisition device.
dB
decibel—The unit for expressing a logarithmic measure of the ratio of
two signal levels: dB = 20log10 V1/V2, for signals in volts.
DC
Direct Current
device
A plug-in data acquisition board, module, card, or pad that can contain
multiple channels and conversion devices.
SCXI-1520 User Manual
G-4
ni.com
Glossary
DIFF
differential input configuration
differential amplifier
An amplifier with two input terminals, neither of which are connected to a
ground reference, whose voltage difference is amplified.
differential input
The two-terminal input to a differential amplifier.
DGND
digital ground signal
DIG GND
See DGND.
DIN
Deutsche Industrie Norme (German Industrial Standard)
DIO
Digital Input/Output
drivers/driver
software
Software that controls a specific hardware device, such as an E/M Series
DAQ device.
droop rate
The rate that a sample-and-hold circuit in hold mode deviates from the true
hold value, expressed in millivolts per second.
E
EEPROM
Electrically Erasable Programmable Read-Only Memory—ROM that can
be erased with an electrical signal and reprogrammed. Some SCXI modules
contain an EEPROM to store measurement-correction coefficients.
EMC
ElectroMagnetic Compliance
EMI
ElectroMagnetic Interference
excitation
Supplying a voltage or current source to energize an active sensor or circuit.
EXTCLK
external clock signal
external trigger
A voltage pulse from an external source that causes a DAQ operation to
begin.
EXTSTROBE*
See SER CLK.
© National Instruments Corporation
G-5
SCXI-1520 User Manual
Glossary
F
F
(1) Fahrenheit—a temperature measurement scale;
(2) farad—a measurement unit of capacitance.
FIFO
First-In First-Out memory buffer
filtering
A type of signal conditioning that allows you to remove unwanted
frequency components from the signal you are trying to measure.
flexible scanning
The hardware capability to sequence through channels in a scan list in any
order.
FSR
Full-Scale Range
full bridge
A Wheatstone bridge in which all four elements are active strain gauges.
G
gain
The factor by which a signal is amplified, sometimes expressed in decibels.
gain accuracy
A measure of deviation of the gain of an amplifier from the ideal gain.
gain error
See gain accuracy.
Gauge Factor
For a given strain gauge, is the fractional resistance change relative to the
strain that caused the resistance change. Thus, Gauge Factor is a measure
of strain-gauge sensitivity.
GF
See Gauge Factor.
H
half bridge
A Wheatstone bridge consisting of two active strain gauges and two passive
fixed-valued resistors.
hold mode
settling time
The time it takes for a sample-and-hold circuit to switch from sampling
mode to hold mode and settle within a given percentage at the true hold
value.
hold step
The difference in the true hold value and the measured hold value in a
sample-and-hold circuit.
SCXI-1520 User Manual
G-6
ni.com
Glossary
HOLD TRIG
hold trigger
Hz
Hertz—Cycles per second of a periodic signal.
I
I/O
Input/Output—The transfer of data to/from a computer system involving
communications channels, operator interface devices, and/or data
acquisition and control interfaces.
ICD
See interchannel delay.
ID
identifier
in.
inch or inches
indirect scanning
The measurement that occurs when a signal passes on the SCXIbus from
the scanned SCXI module to the cabled SCXI module.
input bias current
The current that flows into the inputs of a circuit.
input damage level
The highest voltage level that you can apply to the module without
damaging it.
input impedance
The measured resistance and capacitance between the input terminals of a
circuit.
input offset current
The difference between the bias current flowing out of the input terminals
SX+ and SX–; ideally, is zero so that no error voltage is generated across the
input due to differences in bias current.
instrumentation
amplifier
A very accurate differential amplifier with a high input impedance.
interchannel delay
Amount of time that passes between sampling consecutive channels. The
interchannel delay must be short enough to allow sampling of all the
channels in the channel list, within the scan interval.
interchannel skew
The largest difference in hold mode settling time between
two sample-and-hold circuits on the same module.
intermodule skew
The largest difference in hold mode settling time between
two sample-and-hold circuits on different modules.
© National Instruments Corporation
G-7
SCXI-1520 User Manual
Glossary
L
line resistance
The small, but nonzero, resistance of a lead wire that varies with the lead
length and ambient temperature; can cause measurement error if the lead
wire carries excitation current.
lowpass filter
A filter that passes signals below a cutoff frequency while blocking signals
above that frequency.
M
m
meters
M
(1) Mega, The standard metric prefix for 1 million or 106, when used with
units of measure such as volts and hertz;
(2) mega, The prefix for 1,048,576, or 220, when used with B to quantify
data or computer memory.
max
maximum
microstrain
The unit of strain measurement usually denoted by με; one με represents a
deformation of 10–6, or 0.0001%.
min
(1) minutes
(2) minimum
MIO
Multifunction I/O
MIO device
Refers to the multifunction I/O E/M Series DAQ devices that have MIO or
60XX in their names.
MISO
Master-In-Slave-Out signal
MOSI
Master-Out-Slave-In signal
multiplex
To route one of many input signals to a single output.
SCXI-1520 User Manual
G-8
ni.com
Glossary
multiplexed mode
An SCXI operating mode in which analog input channels are multiplexed
into one module output so that the cabled E/M Series DAQ device has
access to the module’s multiplexed output as well as the outputs of all other
multiplexed modules in the chassis.
mux
multiplexer—A switching device with multiple inputs that sequentially
connects each of its inputs to its single output, typically at high speeds, in
order to measure several signals with a single analog-to-digital converter.
N
NC
Not Connected (signal)
NI-DAQ
The driver software needed in order to use NI E/M Series DAQ devices and
SCXI components.
noise
An undesirable electrical signal—Noise comes from external sources such
as AC power lines, motors, generators, transformers, fluorescent lights,
soldering irons, CRT displays, computers, electrical storms, welders, radio
transmitters, and internal sources such as semiconductors, resistors, and
capacitors. Noise corrupts signals you are trying to measure.
nonlinearity
For an amplifier, a measure of the maximum output deviation from an ideal
linear response in units of percent relative to full scale. The ideal linear
response is taken to be a straight line on a plot of measured output voltage
to measured input voltage with the ends of the line connecting the extremes
of the plot at the full-scale limits.
O
offset error
The output of a system with a zero-volt input.
offset null
compensation
The provision in strain-gauge signal conditioning hardware to remove the
unwanted offset voltage present at the output of a strain-gauge bridge when
no strain is applied.
overvoltage protection
Maximum voltage that does not cause hardware damage.
© National Instruments Corporation
G-9
SCXI-1520 User Manual
Glossary
P
parallel mode
A type of SCXI operating mode in which the module sends each of
its output channels directly to a separate analog input channel of the
E/M Series DAQ device connected to the module.
passband
The range of input frequencies that are passed to the filter output without
attenuation.
PFI
See HOLD TRIG.
Poisson’s ratio
The negative ratio of transverse strain to longitudinal (axial) strain.
pole
A term used to describe the quality of a lowpass filter. In general, the more
poles a lowpass filter has, the better it attenuates frequencies beyond the
cutoff frequency.
port
(1) A digital port consisting of multiple I/O lines on a E/M Series DAQ
device;
(2) a serial or parallel interface connector on a PC.
pp
peak to peak
ppm
parts per million
psi
pounds per square inch
PX–
a negative excitation output terminal
PX+
a positive excitation output terminal
PXI
PCI eXtensions for Instrumentation—An open specification that builds on
the CompactPCI specification by adding instrumentation-specific features.
Q
QTR
Terminal for connection to a quarter-bridge completion resistor.
quarter bridge
A Wheatstone bridge consisting of one active strain gauge and three passive
fixed-valued resistors.
quarter-bridge
completion resistor
The bridge completion resistor in series with the active strain gauge in a
quarter-bridge configuration; the quarter-bridge completion resistor must
have the same nominal resistance value as the strain gauge.
SCXI-1520 User Manual
G-10
ni.com
Glossary
R
remote sense
The method of compensating for voltage drops in bridge excitation leads by
remotely measuring the voltage applied to the bridge.
Rg
gauge resistance
RL
line resistance
RMA
Return Material Authorization
rms
root mean square—The square root of the average value of the square of the
instantaneous signal amplitude; a measure of signal amplitude.
rolloff
The ratio that a system attenuates signals in the stopband with respect to the
passband, usually defined in decibels per octave.
RS
shunt-calibration resistance
RS–
remote-sense terminal, negative input
RS+
remote-sense terminal, positive input
RSC
Rear Signal Connector
RSVD
reserved bit, pin, or signal
RTI
Referred To Input—Calculates a specification relative to the input range.
RTO
Referred To Output
RTSI
Real-Time System Integration
RTSI bus
Real-Time System Integration bus—The NI timing bus that connects an
E/M Series DAQ device directly, by means of connectors on top of the
devices, for precise synchronization of functions.
S
s
seconds
S
samples
© National Instruments Corporation
G-11
SCXI-1520 User Manual
Glossary
S/s
Samples per second—Used to express the rate at which an E/M Series DAQ
device samples an analog signal.
sample
An instantaneous measurement of a signal, normally using an
analog-to-digital converter in an E/M Series DAQ device.
sample and hold
A circuit with a sample mode where the output tracks the input and a hold
mode where the output remains at the last known input before switching
modes.
sample rate
The number of samples a system takes over a given time period, usually
expressed in samples per second.
SCA
Shunt Calibration terminal, circuit A
scan
One or more analog samples taken at the same time, or nearly the same
time. Typically, the number of input samples in a scan is equal to the
number of channels in the input group. For example, one scan acquires one
new sample from every analog input channel in the group.
scan interval accuracy
The minimum interchannel delay needed to achieve a given accuracy.
scan rate
The number of scans a system takes during a given time period, usually
expressed in scans per second.
SCB
Shunt Calibration terminal, circuit B
SCXI
Signal Conditioning eXtensions for Instrumentation
SCXIbus
Located in the rear of an SCXI chassis, the SCXIbus is the backplane that
connects modules in the same chassis to each other.
sensor
A device that converts a physical phenomenon into an electrical signal.
SER CLK
Serial clock signal used to synchronize digital data transfers over the
SER DAT IN and SER DAT OUT lines.
SER DAT IN
serial data input signal
SER DAT OUT
serial data output signal
settling time
The amount of time required for a voltage to reach its final value within
specified accuracy limits.
SCXI-1520 User Manual
G-12
ni.com
Glossary
shunt calibration
The method of calibrating the gain of a strain-gauge data acquisition
channel by placing a resistor of known value in parallel with a bridge
element.
signal conditioning
The manipulation of signals to prepare them for digitizing.
simulated strain
A strain measurement where the change in bridge output voltage is not
caused by deformation of the specimen being measured; rather, it is caused
by temporarily connecting a known resistance in parallel with one of the
bridge elements while all the strain gauges in the bridge remain unstrained.
simultaneous sample
and hold
A series of sample-and-hold circuits that are connected in a matter so as to
switch modes in unison.
Slot 0
Refers to the power supply and control circuitry in the SCXI chassis.
SLOT0SEL
Slot 0 select signal
SPICLK
serial peripheral interface clock signal
spot noise
The rms noise voltage or rms noise current in a frequency band 1 Hz wide
at the specified frequency.
STC strain gauge
self-temperature compensating strain gauge—Has a resistive temperature
coefficient that counteracts the thermal expansion coefficient of the
material to which the gauge is bonded; thus, makes the system insensitive
to changes in temperature.
strain
The fractional deformation of a body under an applied force; is usually
given in the units of microstrain, where one microstrain represents a
deformation of 10–6, or 0.0001%.
SX–
negative signal input terminal for channel X
SX+
positive signal input terminal for channel X
SYNC
Synchronization pulse for scanning (only used with modules featuring
simultaneous sample and hold).
system noise
A measure of the amount of noise seen by an analog circuit or an ADC
when the analog inputs are grounded.
© National Instruments Corporation
G-13
SCXI-1520 User Manual
Glossary
T
TEDS
Transducer Electronic Data Sheets
tensile strain
Strain that results from an object being stretched; has a positive value.
track-and-hold
See simultaneous sample and hold.
TRIG0
trigger 0
TTL
Transistor-Transistor Logic
typ
typical
U
UL
Underwriters Laboratory
unipolar
A voltage range that only spans positive voltages.
V
V
volts
VDC
volts, direct current
VI
Virtual Instrument—(1) A combination of hardware and/or software
elements, typically used with a PC, that has the functionality of a classic
stand-alone instrument;
(2) A LabVIEW software module (VI), which consists of a front panel user
interface and a block diagram program.
virtual channels
Channel names that can be defined outside the application and used without
having to perform scaling operations.
voltage excitation
A source that supplies the voltage needed by a sensor for its proper
operation.
Vr
V CH
CH
V
--------–  -------- V EX  STRAINED  V EX  UNSTRAINED
Vrms
volts, root mean square
SCXI-1520 User Manual
G-14
ni.com
Glossary
W
W
watts
Wheatstone bridge
A circuit arrangement consisting of four resistive elements in a diamond
pattern; with excitation voltage applied across two opposing terminals,
small resistance changes in the elements are easily detected by measuring
voltage changes across the remaining two terminals.
working voltage
The highest voltage with respect to ground that should be applied to an
input terminal during normal use, normally well under the breakdown
voltage for safety margin. Includes both the signal and common-mode
voltages.
© National Instruments Corporation
G-15
SCXI-1520 User Manual
Index
A
configuration
troubleshooting self-test verification, 1-7
configuration settings
excitation level, 3-2
filter bandwidth, 3-2, 4-25
gain, 3-3, 4-24
null potentiometers, 3-4
connecting SCXI-1520 to DAQ device. See
DAQ devices
conventions used in the manual, iv
amplifier specifications, A-4
analog input, specifications, A-1
analog triggering, D-6
B
block diagram, 4-19
bridge completion specifications, A-6
bridge configuration
full-bridge configuration I, 2-6, 4-13
full-bridge configuration II, 2-7, 4-14
full-bridge configuration III, 2-8, 4-16
half-bridge configuration I, 2-4, 4-9
half-bridge configuration II, 2-5, 4-11
overview, 3-1, 4-21
quarter-bridge configuration I, 2-1, 4-4
quarter-bridge configuration II, 2-2, 4-6
questions about, D-4
D
DAQ devices
cabling restrictions with plug-in E/M
Series DAQ devices, D-3
connecting to SCXI-1520 for multiplexed
scanning
in PXI combination chassis, 1-5
in SCXI chassis, 1-5
unavailable digital lines, D-2
digital settings, unavailable with DAQ device
connected (table), D-2
digital triggering, D-6
documentation
conventions used in the manual, iv
dynamic specifications, A-4
C
calibration
internal calibration
overview, 5-37
procedure for, 5-37
using C-based ADE, 5-38
using LabVIEW, 5-37
shunt calibration
questions about, D-4
specifications, A-6
theory of operation, 4-27
C-based environment
configuration questions, D-5
internal calibration of SCXI-1520, 5-38
common questions, D-1
© National Instruments Corporation
E
electromagnetic compatibility
specifications, A-8
environmental specifications, A-7
excitation
maximum allowable voltages (table), 3-2
questions about, D-4
setting excitation voltage level, 3-2
I-1
SCXI-1520 User Manual
Index
L
specifications, A-5
theory of operation, 4-22
external triggering, D-6
LabVIEW software
internal calibration of SCXI-1520, 5-37
questions about, D-3
F
M
filters
bandwidth configuration, 3-2, 4-25
questions about, D-4
specifications, A-4
front connector, pin assignments (table), 2-11
full-bridge configuration I, 2-6, 4-13
full-bridge configuration II, 2-7, 4-14
full-bridge configuration III, 2-8, 4-16
Macintosh operating system, D-4
maximum working voltage specifications, A-7
Measurement & Automation Explorer
removing SCXI-1520, C-1
self-test verification
troubleshooting, 1-7
measurements
calibrating SCXI-1520, 5-37
pin assignments, terminal
assignments, 2-10
strain gauge connections
full-bridge configuration I, 2-6, 4-13
full-bridge configuration II, 2-7, 4-14
full-bridge configuration III, 2-8,
4-16
half-bridge configuration I, 2-4, 4-9
half-bridge configuration II, 2-5,
4-11
quarter-bridge configuration I, 2-6,
4-13
quarter-bridge configuration II, 2-7,
4-14
remote sense, 2-9
multiplexed mode operation
connecting to SCXI-1520 for DAQ device
in PXI combination, 1-5
in SCXI chassis, 1-5
questions about, D-3
G
gain
configuration, 3-3, 4-24
questions about, D-4
H
half-bridge configuration I, 2-4, 4-9
half-bridge configuration II, 2-5, 4-11
I
installation
connecting to DAQ device for
multiplexed scanning
in PXI combination chassis, 1-5
in SCXI chassis, 1-5
into SCXI chassis, 1-5
removing SCXI-1520
from Measurement & Automation
Explorer, C-1
from SCXI chassis, C-1
internal calibration. See calibration
SCXI-1520 User Manual
I-2
ni.com
Index
N
removing SCXI-1520
from Measurement & Automation
Explorer, C-1
from SCXI chassis, C-1
NI-DAQ software, D-1, D-4
null compensation
specifications, A-5
theory of operation, 4-25
null potentiometers
coarse and fine control codes (table), 4-26
configuring, 3-4
questions about, D-4
S
safety specifications, A-8
SCXI chassis
connecting SCXI-1520 to DAQ
device, 1-5
removing SCXI-1520, C-1
SCXI-1200, D-2
SCXI-1310 connector and shell assembly, 1-3
SCXI-1314 terminal block, 1-2, D-5
SCXI-1314T terminal block, 1-2, D-6
SCXI-1520
block diagram, 4-19
calibration, 5-37
common questions, D-1
configuration settings, 3-1
digital signals (table), D-2
specifications, A-1
taking measurements. See measurements
theory of operation
excitation, 4-22
null compensation, 4-25
shunt calibration, 4-27
SCXI-1600, D-2
self-test verification
troubleshooting, 1-7, D-1
shunt calibration
questions about, D-4
specifications, A-6
theory of operation, 4-27
signal connections
digital signals (table), D-2
front connector, pin assignments
(table), 2-11
O
operation of SCXI-1520. See theory of
operation
P
physical specifications, A-7
pin assignments
front connector (table), 2-11
terminal assignments, 2-10
potentiometers. See null potentiometers
power requirements (from SCXI
backplane), A-6
power-up state of SCXI-1520, D-4
PXI combination chassis, 1-5
Q
quarter-bridge configuration I, 2-1, 4-4
quarter-bridge configuration II, 2-2, 4-6
questions and answers, D-1
R
random scanning, D-3
regulatory compliance specifications, A-8
remote sense, 2-9
© National Instruments Corporation
I-3
SCXI-1520 User Manual
Index
questions about, D-5
remote sense, 2-9
software, NI-DAQ version required, D-1
specifications
amplifier, A-4
analog input, A-1
bridge completion, A-6
dynamic, A-4
electromagnetic compatibility, A-8
environmental, A-7
excitation, A-5
filter, A-4
maximum working voltage, A-7
null compensation, A-5
physical, A-7
power requirements (from SCXI
backplane), A-6
regulatory compliance, A-8
safety, A-8
shunt calibration, A-6
stability, A-5
track-and-hold, A-4
transfer, A-1
stability specifications, A-5
strain gauge connections
full-bridge configuration I, 2-6, 4-13
full-bridge configuration II, 2-7, 4-14
full-bridge configuration III, 2-8, 4-16
half-bridge configuration I, 2-4, 4-9
half-bridge configuration II, 2-5, 4-11
quarter-bridge configuration I, 2-1, 4-4
quarter-bridge configuration II, 2-2, 4-6
SCXI-1520 User Manual
T
taking measurements. See measurements
TBX-96 terminal block, 1-3
TEDS, D-6
theory of operation
block diagram, 4-19
excitation, 4-22
null compensation, 4-25
shunt calibration, 4-27
track-and-hold specifications, A-4
transfer specifications, A-1
triggering
analog, D-6
digital, D-6
external, D-6
troubleshooting
incorrect test and verification, D-1
questions and answers, D-1
self-test verification, 1-7
V
verifying and self-testing the configuration
troubleshooting, 1-7, D-1
I-4
ni.com

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement