Airless Sprayer Plus HIGH PERFORMANCE AIRLESS SPRAYER 2 years Guarantee ! NOT FOR COMMERCIAL USE ! AUS Airless Sprayer Plus Warning! Attention: Danger of injury by injection! Airless units develop extremely high spraying pressures . Danger 1 Never put your fingers, hands or any other parts of the body into the spray jet! Never point the spray gun at yourself, other persons or animals. Never use the spray gun without safety guard . Do not treat a spraying injury as a harmless cut. In case of injury to the skin through coating materials or solvents, consult a doctor immediately for quick and expert treatment. Inform the doctor about the coating material or solvent used. 2 The operating instructions state that the following points must always be observed before starting up: 1. Faulty units must not be used. 2. Secure spray gun using the safety catch on the trigger. 3. Ensure that the unit is properly earthed. The connection must take place through a correctly earthed two-pole and earth socket outlet. 4. Check allowable operating pressure of high-pressure hose and spray gun. 5. Check all connections for leaks. 3 The instructions regarding regular cleaning and maintenance of the unit must be strictly observed. Before any work is done on the unit or for every break in work the following rules must be observed: 1. Release the pressure from spray gun and hose. 2. Secure the WAGNER spray gun using the safety catch on the trigger. 3. Switch off unit. Be safety-conscious! Airless Sprayer Plus Congratulations for the purchase of your WAGNER Airless high pressure spray gun. Read this manual carefully before the initial use of this equipment and observe the safety instructions. Keep manual and safety instructions carefully stored. You have purchased a quality product which requires careful maintenance and care in order to function perfectly. Important! After each use, the equipment should be cleaned. Not cleaning the equipment leads to malfunctioning! For faults caused by crud, no guarantee claim will be granted. In case of malfunctioning, check the cleaned equipment once again prior to sending it in to the service department. Explanation of symbols used Danger i Indicates an immediate danger. Unless avoided, death or serious injuries will result. Indicates tips for use and other particularly useful information. Wear suitable ear protection when working. Wear suitable respiratory equipment when working. Wear suitable safety gloves when working. General Safety Instructions Warning! Danger Read all safety notifications and instructions. Failure to comply with the safety notifications and instructions provided may result in electric shock, fire and/or serious injury. The term "power tool" used below covers both mainsoperated power tools (with mains lead) and accumulator-operated power tools (without mains lead). 1. Work area safety a) Keep work area clean and well lit. Cluttered or dark areas invite accidents. b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. 2. Electrical Safety a) Power tool plugs must match the outlet. Never AUS modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. f) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock. 3. Personal safety a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents. d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. 1 Airless Sprayer Plus AUS g) This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. 4. Power tool use and care a) Do not force the power tool. Use correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. c) Disconnect the plug from the power source and/ or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. d) Store idle power tools out of reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool's operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. 5. Service a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. b) If the supply cord is damaged, it must be replaced by the manufacturer or it’s service agent or a similarly qualified person in order to avoid a safety hazard. 2 Health protection Danger Caution! Wear breathing equipment: Paint mist and solvent vapors are damaging to health. Always wear breathing equipment and only work in well ventilated rooms or using supplementary ventilating equipment. It is advisable to wear working clothing, safety glasses, ear protection and gloves Flammable materials Do not use the spray guns to spray flammable substances. Danger Explosion protection Danger Do not use the unit in work places which are covered to the explosion protection regulations. Danger of explosion and fire through sources of flame during spraying work Danger There may be no sources of flame such as, for example, open fires, smoking of cigarettes, cigars or tobacco pipes, sparks, glowing wires, hot surfaces, etc. in the vicinity. Electrostatic charging (formation of sparks or flame) Danger Under certain circumstances, electrostatic charging can occur on the unit due to the rate of flow of the coating material when spraying. On discharging this can result in the emergence of sparks or fire. It is therefore necessary that the unit is always earthed through the electrical installation. The connection must take place through a correctly earthed twopole-and-earth socket outlet. Ventilation Good natural or artificial ventilation must be ensured in order to avoid the risk of explosion or fire and damage to health during spray work. Secure device and spray gun All hoses, fittings, and filter parts must be secured before operating spray pump. Unsecured parts can eject at great force or leak a high pressure fluid stream causing severe injury. Always secure the spray gun when mounting or dismounting the nozzle and in case of interruption to work. Airless Sprayer Plus Recoil of spray gun Danger In case of high operating pressure, pulling the trigger can effect a recoil force of up to 15 N. If you are not prepared for this, your hand can be thrust backwards or your balance lost. This can lead to injury. Continuous stress from this recoil can cause permanent damage to health. Max. operating pressure Max. permissible operating pressure for spray gun, spray gun accessories and high-pressure hose may not fall short of the maximum operating pressure of 200 bar (20 MPa) stated on the unit. AUS Connecting the device A properly earthed socket outlet with earthing contact must be used for connection. The connection must be equipped with a residual current protective device with INF ≤ 30 mA. Setting up the unit Danger Coating substance Caution against dangers that can arise from the sprayed substance and observe the text and information on the containers or the specifications given by the substance manufacturer. Do not spray any liquid of unknown hazard potential. High-pressure hose (safety note) Attention, danger of injury by injection! Wear and tear and kinks as well as usage that is not appropriate to the purpose Danger of the device can cause leakages to form in the high-pressure hose. Liquid can be injected into the skin through a leakage. High-pressure hoses must be checked thoroughly before they are used. Replace any damaged high-pressure hose immediately. Never repair defective high-pressure hoses yourself! Avoid sharp bends and folds: the smallest bending radius is about 20 cm. Do not drive over the high-pressure hose. Protect against sharp objects and edges. Never pull on the high-pressure hose to move the device. Do not twist the high-pressure hose. Do not put the high-pressure hose into solvents. Use only a wet cloth to wipe down the outside of the hose. Lay the high-pressure hose in such a way as to ensure that it cannot be tripped over. Electrostatic charging of spray guns and the highpressure hose is discharged through the high-pressure hose. For this reason the electric resistance between the connections of the high-pressure hose must be equal or lower than 197 kΩ/m (60 kΩ/ft.). For reasons of function, safety and durability, only use genuine WAGNER high-pressure hoses and spray nozzles. For overview see „Spare parts lists“. The risk of damage rises with the age of the high-pressure hose. Wagner recommends replacing highpressure hoses after 6 years. i i When working indoors: Vapors containing solvents may not be allowed to build up in the area of the device. Setting up the unit on the side a way from the sprayed object. A minimum distance of 5 m between the unit and spray gun is to be maintained. When working outdoors: Vapors containing solvents may not be allowed to blow toward the unit. Note the direction of the wind. Set the unit up in such a way that vapors containing solvents do not reach the unit and build up there. A minimum distance of 5 m between the unit and spray gun is to be maintained. Maintenance and repairs Danger Before carrying out any work on the device, relieve the pressure and unplug the power plug from the socket. Cleaning the unit Danger Danger of short circuit through penetrating water! Never spray down the unit with highpressure or high-pressure steam cleaners. Cleaning units with solvents Danger When cleaning the unit with solvents, the solvent should never be sprayed or pumped back into a container with a small opening (bunghole). An explosive gas/air mixture can be produced. The container must be earthed. Do not use flammable materials for cleaning purposes. Earthing of the object The object to be coated must be earthed. i If liquids collect in the area underneath the outlet valve, this could be due to a leak in the set of pistons. If operations continue, the liquid can leak and dirt might get under the device. 3 Airless Sprayer Plus AUS Usabel materials •Internal emulsions •Paints •Acrylic paints •Glazes •Wood preservatives •Mordants •Primers •Wash primer •Plant protective agents •Under sealants •Hollow-space sealants •Disinfection agents •Oils Unsuitable materials •Paints and lacquers containing heavily abrasive components like outdoor emulsion / dispersion wall paints Silicate paints Flammable materials • • Field of application Coating of interior walls as well as small and mediumsized objects outdoors (e.g. garden fences, garage doors, etc.). Industrial use is excluded. 4 Technical data Voltage 240V, 50 Hz Power consumption 625 W Protection class I Maximum pressure 19.3 MPa (193 bar) Flow rate at 140 bar (0 bar) 0.9 l/min (1,6 l/min) Maximum temperature of coating material 43°C Sound pressure level* Uncertainty 81 dBA K= 4 db Sound pressure output* Uncertainty 94 dBA K= 4 db Oscillation level** Uncertainty < 2.5 m/s² K = 1.5 m/s² Maximum ambient temperature 40°C Pump system piston pump volume upper container, max. 7.5 l Max. nozzle size L (0,017“) Weight, ready to spray 10.5 kg * Measured in accordance with EN 50144-2-7:2000 ** Measured in accordance with EN 60745-1 Information about the oscillation level The specified oscillation level has been measured according to a standard test procedure and can be used to compare against electric tools. The oscillation level is also for determining an initial assessment of the vibrational strain. Attention! The vibration emission value can differ from the specified value when the electric tool is actually in use, depending on how the electric tool is being used. It is necessary to specify safety measures to protect the operating personnel. These measures are based on an estimated shutdown during the actual conditions of use (all parts of the operating cycle are taken into consideration here, for example periods when the electric tool is switched off, and, when it is switched on but running without any load). COMPONENTS AND ASSEMBLY Airless Sprayer Plus Components AUS Controls and functions • • • Spray gun with filter Spray tip assembly 10 mtr. long, 1/4 Zoll diameter high pressure hose. ON/OFF switch The ON/OFF switch turns the unit on and off (O = OFF, l = ON) Spray Gun The spray gun controls the delivery of the fluid being pumped. Spray Hose The spray hose connects the gun to the pump. Return Tube Fluid is sent back out through the return tube to the hopper when priming. PRIME/SPRAY knob The PRIME/SPRAY knob directs fluid to the spray hose when set to SPRAY, or the return tube when set to PRIME. Tools needed for assembly •Two adjustable wrenches. WARNING Do not plug in the unit until setup is complete. ON/OFF Switch Inlet filter (inside of hopper) = ON Handle = OFF Hopper lid Return tube Motor housing Hopper PRIME/SPRAY knob Rear handle PRIME ON/OFF switch Outlet valve Inlet valve tool Tip storage PRIME position PRIME/SPRAY knob Spray gun SPRAY Frame SPRAY Trigger lock Filter (yellow) preassembled in gun Trigger Filter (red) PRIME Tip Tip guard SPRAY position Spray hose Assembly 1 Place the handle over the unit frame. Insert the bolts and tighten the wing nuts over the lock washers. 2 Thread one end of the high pressure spray hose to the outlet valve. Tighten with an adjustable wrench. 3 Thread the other end of the hose to the spray gun. Hold the gun with one adjustable wrench, and tighten the hose nut with the other. 5 Important information AUS Paint straining It is recommended that in order to avoid premature tip and filter clogging you should strain your paint before spraying. Follow manufacturer’s recommendations. Airless Sprayer Plus Plugging in the sprayer 1) Check that the ON/OFF switch is in the OFF postion. 2) The connection must be made by correctly grounded plug socket. Select tip and gun filter O Use the proper gun filter based on the tip size being used. XS 40° spray angle/ 0,23 mm holeg M 50° spray angle// 0,38 mm hole Paint For thin materials like lacquers and stains. Filter For thick materials like acrylic paints and primers. yellow Red WARNING Always lock the trigger off when attaching the spray tip or when the spray gun is not in use. Locking the gun The gun is secured when the trigger lock is at a 90° angle (perpendicular) to the trigger in either direction. Unlocking the gun To unlock the gun, turn the trigger lock to be in line with the trigger. 6 WARNING Be sure to follow the pressure relief procedure when shutting the unit off FOR ANY PURPOSE. This procedure is used to relieve pressure from the spray hose. 1) Lock the spray gun off and flip the ON/OFF switch to the OFF position. 2) Turn the PRIME/SPRAY knob to PRIME. 3) Unlock the spray gun and then trigger it onto a scrap piece of wood or cardboard. 4) Lock the spray gun. O SPRAY Locking and unlocking the gun Pressure relief procedure PRIME Tip Size Preparation Airless Sprayer Plus Make pump ready for operation 1) Make sure the inlet filter is in place inside the hopper. If it is not, snap in place as shown. Suck in material Tab Perform the following steps, without the spray tip mounted to the gun. 3) Pull the return tube from the hopper and hold it over a waste container. PRIME SPRAY 1) Unlock the spray gun and turn the PRIME/SPRAY knob to PRIME. 2) Push the tab on top of the filter down once. This will ensure proper operation of the inlet valve. 2) Trigger and HOLD the spray gun into a waste container. l SPRAY PRIME 4) Turn the PRIME/SPRAY knob to PRIME. 5) Plug in the sprayer, and move the ON/OFF switch to the ON position. AUS 3) Switch the pump on. 7) Fill your hopper with the material you plan to spray. Do not exceed the fill line as shown. Replace the hopper lid. O Fill line l PRIME 6) Trigger the gun into the waste container once more to be sure that no pressure is left in the hose. 7) Lock the spray gun off. 8) Thread the spray tip assembly onto the gun. Tighten by hand. SPRAY 8) Leave the PRIME/SPRAY knob on PRIME and switch your unit ON once more and make sure that material is flowing from the return tube. 5) Release trigger, turn the PRIME/SPRAY knob to PRIME and turn pump OFF . SPRAY SPRAY We recommend performing the following steps with water first of all, in order to check that the system and all connections are watertight. Keep hands clear from fluid stream. 4) While holding the trigger, turn the PRIME/SPRAY knob to SPRAY. Hold the trigger until all air, water, or solvent is purged from the spray hose and paint is flowing freely. PRIME O WARNING PRIME 6) Switch the pump to OFF. Remove the return tube from the waste container and secure it to the hopper. l Any fluids remaining in the pump and the return tube will flow out of the return tube. Let the pump run until no fluid is coming from the return tube. Begin tightening the tip at this angle to achieve the desired spray angle when tight. 9) Insert spray tip (tip pointing in the spray direction). Your device is now ready for operation. 7 SPRAYING AUS Practice Airless Sprayer Plus TIP: CAUTION Be sure that the paint hose is free of kinks and clear of objects with sharp cutting edges. SPRAY Approximately 25 - 30 cm Wrong way Right way PRIME l 1) Switch the pump ON and turn the PRIME/SPRAY knob to SPRAY. 2) When the motor shuts off, unlock the spray gun and spray a test area to check the spray pattern. When enough pressure has built up in the hose, the motor will shut off automatically. The motor will cycle on and off automatically as it needs pressure. Keep the spray gun perpendicular to the surface, otherwise one end of the pattern will be thicker than the other. TIP: Keep the spray gun at right angles to the surface. This means moving your entire arm back and forth rather than just flexing your wrist. Light Coat Heavy Coat Light Coat Good spray pattern Bad spray pattern (tailing) If your pattern is tailing, your spray tip might have an obstruction, your spray gun filter might be clogged or your spray tip might be worn or color is diluted too few. Refer to Spraying Troubleshooting on the next page. Do not flex wrist while spraying. TIP: The spray gun should be triggered by turning it on and off with each stroke. Do not trigger the gun during the middle of a stroke. This will result in an uneven spray and splotchy coverage. Proper way to trigger the spray gun Spraying technique The key to a good paint job is an even coating over the entire surface. This is done by using even strokes. Follow the TIPS, below. TIP: Keep stroke even Keep your arm moving at a constant speed and keep the spray gun at a constant distance from the surface. The best spraying distance is 25 to 30 cm between the spray tip and the surface. Start stroke Even coat throughout Approximately 25-30cm Keep stroke smooth and at an even speed. 8 Approximately 25-30cm Pull trigger Keep steady Release trigger End stroke ADDITIONAL TIPS Overlap each stroke by about 30%. This will ensure an even coating. When you stop painting, follow PRESSURE RELIEF PROCEDURE and unplug electrical cord. Keep the hopper lid placed on the hopper during spraying. This will prevent debris from falling into your spray material. IF YOU EXPECT TO BE AWAY FROM YOUR SPRAYER FOR MORE THAN ONE HOUR, FOLLOW THE SHORT-TERM STORAGE PROCEDURE DESCRIBED IN THE STORAGE SECTION OF THIS MANUAL (page 12). Airless Sprayer Plus SPRAYING TROUBLESHOOTING The following is a short list of minor difficulties you might encounter while spraying. If any of these occur, it will reduce the flow of material, making your spray pattern poor, or material will fail to spray from the gun. Follow the guidelines on this page to correct any one of these problems. Unclogging the spray tip Unclogging the spray gun filter This filter must be cleaned every time you use your sprayer. When using thicker paints, the filter might need to be cleaned more often. 1) Perform Pressure Relief Procedure (page 6). 2) Remove the closure by turning it (take care not to lose the spring). Filter top (tapered end) WARNING Do not attempt to unclog or clean the tip with your finger. Filter CAUTION Do not use a needle or other sharp pointed instrument to clean the tip. The hard tungsten carbide can chip. If the spray pattern becomes distorted or stops completely while the gun is triggered, follow these steps: 1) Turn the pump off, and release the trigger and lock the gun off. AUS Hole Spring Closure 3) Remove the filter from the spray gun housing and clean with the appropriate cleaning solution (warm, soapy water) When cleaning filter, look for sediments in the spraying material you are using. Refer to Paint Straining, (page 6). O 2) Rotate the reversible tip arrow 180° so that the point of the arrow is toward the rear of the gun. Under pressure, the spray tip may be very difficult to turn. Turn the PRIME/SPRAY knob to PRIME and trigger the gun. This will relieve pressure and the tip will turn more easily. 3) Turn the PRIME/SPRAY knob to SPRAY. 4) Inspect the filter for holes (see Hole picture, above). Replace if holes are found. CAUTION NEVER POKE THE FILTER WITH A SHARP INSTRUMENT! 5) Replace the cleaned filter, tapered end first, into the gun housing. The tapered end of the filter must be loaded properly into the gun. Improper assembly will result in a plugged tip or no flow from the gun. 6) Insert the spring in the closure and tighten the closure on the gun housing again. Uunclogging the inlet filter 4) Unlock the gun and squeeze the trigger, pointing the gun at a scrap piece of wood or cardboard. This allows pressure in the spray hose to blow out the obstruction. When the nozzle is clean, paint will come out in a high pressure stream. If paint still will not spray from the spray tip, follow the steps on the next column. 5) Release the trigger and lock the gun off. 6) Reverse the tip so the arrow points foward again (SPRAY position). 1) Perform Pressure Relief Procedure, (page 6). 2) Empty the hopper of all spraying material (see Emptying the Hopper, page 10). 3) Remove the inlet filter from the hopper. You may need to use a screwdriver to pry the filter loose. 4) Clean the inlet filter using the appropriate cleaning Inlet filter solution (warm, soapy water). 5) Replace filter. If after having completed all of the steps on this page you are still experiencing problems spraying, refer to the TROUBLESHOOTING page (page 13) 7) Unlock the gun and resume spraying. 9 CLEANUP AUS Important cleaning notes Airless Sprayer Plus Purging the paint hose Rinsing the hopper These steps will allow you to recover READ THESE NOTES AND WARNINGS excess paint left over in the paint hose. BEFORE YOU START TO CLEAN YOUR 1) Lock the gun, remove spray tip SPRAYER! assembly, and turn the PRIME/SPRAY Thorough cleaning and lubrication knob to PRIME. of the sprayer is the most important step you can take to ensure proper operation after storage. Clean the spray device and components with a suitable cleaning agent (e.g. warm soapy water for water-soluble spray materials). 2) Fill the hopper with the appropriate Make sure to dispose cleaning cleaning solution. solution properly when finished 3) Hold the spray gun against the cleaning your sprayer. side of the paint can and hold the trigger. • PRIME SPRAY • 1) Thoroughly rinse out the hopper using the appropriate cleaning solution. Make sure you do not drip any cleaning solution into the motor housing. 2) Remove the inlet filter from the bottom of the hopper and clean. You may need to use a screwdriver to pry the filter loose. • l PRIME Top handle SPRAY Let the pump run until all paint is purged from the hose and cleaning solution is coming out of the gun. 6) Release the trigger and turn the PRIME/SPRAY knob to PRIME. 7) Hold the spray gun against the side of a separate container and hold the trigger. Flushing the sprayer 1) Fill the hopper with NEW cleaning solution. 2) Turn the PRIME/SPRAY knob to PRIME, turn the pump to ON . SPRAY 1) Perform all the steps of the Pressure Relief Procedure (page 6). 2) Remove the lid from the hopper. 3) Grab top handle of the sprayer with one hand, grab rear handle with the other. 4) Lift and tilt the sprayer so that material will pour from one of the front corners of the hopper and into its original container. 3) Replace the filter and properly dispose of the cleaning solution. PRIME 4) While holding the trigger, turn the pump ON, and turn the PRIME/ SPRAY knob to SPRAY. O Inlet filter l Emptying the hopper 3) Let the pump circulate the cleaning solution out the return tube for 2-3 minutes. 4) Turn the pump OFF . Rear handle 8) Turn the PRIME/SPRAY knob to SPRAY and trigger the gun until the fluid coming out of the gun is clear. Front corners WARNING The unit, when filled with spraying material, can be heavy. Make sure to lift with your legs and not your back in order to reduce the risk of injury. CAUTION Make sure your floors and furnishings are protected with drop cloths to avoid property damage. 10 You might need to add more cleaning solution to the hopper. 9) Turn the PRIME/SPRAY knob to PRIME and trigger gun once more to relieve pressure. O 5) Properly dispose of cleaning solution and move on to Cleaning the Spray Gun Components, next page. CLEANUP Airless Sprayer Plus AUS Cleaning the spray gun components Cleaning the inlet valve 1) Perform Pressure Relief Procedure, page 6. Cleaning or servicing the inlet valve may be required if the unit has priming problems. This may be caused by improper cleaning and/or storage. 2) Remove spray gun from the paint hose using adjustable wrenches. 3) Remove filter from spray gun (refer to Unclogging the Spray Gun Filter, page 9). 4) Remove spray tip from spray guard assembly. Filter Spring Closure 5) Clean spray tip and filter with a soft-bristled brush and the appropriate cleaning solution. Be sure to remove and clean the washer and saddle seat located in the rear of the spray tip assembly. Saddle seat Washer 6) Pour a few drops of household oil inside the gun housing (see area indicated below by arrow). 7) Reassemble spray gun: •Insert gun filter with the tapered end first and screw down closure with spring. Install spray tip, saddle seat and washer, and replace spray guard assembly. Filter • 1) Remove the inlet filter from the bottom of the hopper. You may need to use a screwdriver to pry the filter loose. 2) Insert the inlet valve tool into the inlet fitting. Twist counterclockwise and remove from its housing. You willl need to attach the inlet valve tool to a ratchet 3/8 Zoll wrench extension in order to remove it. 3) Inspect the three inlet Inlet fitting fitting O-rings on the inlet O-ring fitting. Clean or replace, and lubricate with household Inlet fitting oil. O-ring DO NOT remove the O-rings on the inlet fitting to clean them. Inlet Remove ONLY if you plan to fitting replace them. 4) Retrieve the inlet valve and the inlet valve O-ring from the Inlet fitting inlet fitting housing. Clean O-ring or replace and lubricate the O-ring with a light household Inlet oil. valve 5) Set the inlet valve O-ring back Inlet into the housing, and set the valve inlet valve on top of it. O-ring 6) Replace inlet fitting into the housing. Tighten with the inlet valve tool and ratchet. Replacing the outlet valve Spring Closure 8) Thread the paint hose back onto the spray gun. Tighten with a wrench. IMPORTANT! If you cleaned your pump, it is recommended that you flush the pump again using warm, soapy water to prepare it for storage. Repeat Flushing the Pump instructions. Replacement of the outlet valve may be necessary if your spray performance remains poor after having performed all the steps contained in the Spraying Troubleshooting section of this manual. 1) Unscrew the outlet valve from the outlet valve housing using an adjustable wrench. 2) Inspect the inside of the outlet valve housing. Remove any accumulated paint. 3) Replace with a new outlet valve. Tighten into outlet valve housing with an adjustable wrench. 11 STORAGE AUS Airless Sprayer Plus Short-term storage (up to 8 hours) Preparing the sprayer for longterm storage Shutdown 1) Make sure you have already completed the Cleanup steps on pages 10-11. 2) Remove the inlet filter. You may need to use a screwdriver to pry it loose. SPRAY PRIME 1) Perform all the steps of the PRESSURE RELIEF PROCEDURE (page 6). O Inlet filter 2) Pour 1/2 cup water slowly on top of the paint to prevent it from drying. Replace the hopper lid. 3) Wrap the spray gun assembly in a damp cloth and place it in a plastic bag. Seal the bag shut. 3) Pour approximately two ounces of light household oil into the inlet valve. Inlet valve 4) Unplug the sprayer. 5) Place the sprayer in a safe place out of the sun for shortterm storage. Startup PRIME SPRAY Tab SPRAY PRIME 12 O 6) Replace the inlet filter and push the tab on the filter. l 1) Remove the gun from the plastic bag and stir the water into the paint. 2) Check to be sure the PRIME/ SPRAY knob is set to PRIME. 3) Plug sprayer in and turn the switch to ON. 4) Turn the PRIME/SPRAY knob to SPRAY. 5) Test the sprayer on a practice piece and begin spraying. 4) Remove hose from outlet valve, place a rag over the outlet valve, and turn the switch ON. Let the unit run for five seconds. 5) Switch the pump OFF. 7) Wipe the entire unit, hose and gun with a damp cloth to remove accumulated paint. 8) Replace the high pressure hose to the outlet valve and replace the hopper lid. MAINTENANCE Airless Sprayer Plus Daily maintenance Pump performance is the only reliable indicator of when to replace wear parts. Refer to the Troubleshooting section for more information on when to use these kits. The only daily maintenance necessary is thorough cleaning. Follow the cleaning procedures in this manual. Extended maintenance Some pump parts eventually wear out from use and must be replaced. The following is a list of available repair kits. TROUBLESHOOTING WARNING CAUSE 1) The sprayer is not plugged in. 2) The ON/OFF switch is set to OFF. 3) The sprayer shuts off while still under pressure. 4) No voltage is coming from the wall plug. 5) The extension cord is damaged or has too low a capacity. 6) There is a problem with the motor. B. T he sprayer starts but does 1) The unit will not prime properly or has lost prime. not draw in paint when 2) The hopper is empty. the PRIME/SPRAY knob is set to PRIME. 3) The unit is not on level ground. 4) The inlet filter is clogged. 5) The inlet or outlet valve is stuck. C. T he sprayer draws up paint but the pressure drops when the gun is triggered. Kit Part # Description 2350456 Inlet and outlet valve kit Before servicing, always release system pressure by following PRESSURE RELIEF PROCEDURE (page 6). PROBLEM A. The sprayer does not start. 6) 7) 1) 2) 3) AUS The inlet valve is worn or damaged. The PRIME/SPRAY valve is plugged. The spray tip is worn. The inlet filter is clogged. The gun or spray tip filter is plugged. 4) The paint is too heavy or coarse. 5) The outlet valve assembly is dirty or worn. 6) The inlet valve assembly is damaged or worn. 1) The PRIME/SPRAY valve is dirty or worn. D. T he PRIME/SPRAY valve is on SPRAY and there is flow through the return tube. E. T he spray gun leaks. 1) Internal parts of the gun are worn or dirty. F. T he tip assembly leaks. 1) The tip was assembled incorrectly. 2) A seal is worn. G. The spray gun will not 1) The spray tip or the gun filter is plugged. spray. 2) The spray tip is in the CLEAN position. 3) PRIME/SPRAY knob not set on SPRAY. H. T he paint pattern is tailing. 1) The gun, the tip, or the inlet filter is plugged. 2) The tip is worn. 3) The paint is too thick. 4) Pressure loss. SOLUTION 1) Plug the sprayer in. 2) Turn the ON/OFF switch to ON. 3) Motor will cycle ON and OFF while spraying as it needs pressure. This is normal. Resume painting. 4) Properly test the power supply voltage. 5) Replace the extension cord. 6) Take sprayer to Wagner Authorized Service Center. 1) Try to prime the unit again. 2) 3) 4) 5) 6) 7) 1) 2) 3) 4) 5) 6) Refill the hopper. Relocate unit to level ground. Clean the inlet filter. Clean the inlet and outlet valves and replace any worn parts.* Inlet may be stuck from old paint. Push inlet filter tab to release. Replace the inlet valve.* Take sprayer to Wagner Authorized Service Center. Replace the spray tip with a new tip.** Clean the inlet filter. Clean or replace the proper filter. Always keep extra filters on hand. Thin or strain the paint. Clean or replace the outlet valve assembly.* Replace the inlet valve.* 1) Take sprayer to Wagner Authorized Service Center. 1) 1) 2) 1) Take the sprayer to a Wagner Authorized Service Center. Check the tip assembly and assemble properly. Replace the seal.* Clean the spray tip or gun filter. Review Unclogging the Spray Tip. 2) Put the tip in the SPRAY position. 3) Turn the PRIME/SPRAY knob to SPRAY. 1) Clean the filters and strain the paint. 2) Replace the spray tip. 3) Thin the paint. 4) Refer to Causes and Solutions for problem C. * Special repair kits with instructions are available for these procedures. Refer to the Parts List (page 14) section of this manual for a list of the kits and their part numbers. ** A dditional parts are available for this procedure. Refer to the Parts List (page 14) section of this manual for a list of the parts and their part numbers. 13 PARTS LIST AUS Airless Sprayer Plus SPRAY GUN 5 1 11 6/7/10 2/3/4 8 9 Item Part # Description Quantity 1 2336 705 Guard Assembly 1 2* 0418 705 Tip XS 1 3* 0418 707 Tip M 1 4* 0418 708 Tip L 1 5 2350 902 Complete gun assembly (incl pos. 1,3,8,9,10,11) 1 6* 0418 711 Filter red 2 7* 0418 713 Filter white 2 8* 2351 004 Spring 1 9 2351 005 Closure 1 10* 0418 712 Filter yellow 2 11* 2337 249 Saddle seat and washer 1 * Wear parts: Not covered by guarantee i If using another nozzle, the right filter must also be used. Tip XS Filter red Tip M Filter yellow Tip L Filter white SPRAYER 1 2 9* 7 3 8 5 4 6 10 Item Part # Description Quantity 1 2337 252 Handle, upper 1 2 2337 292 Hopper lid 1 3 2337 256 Bolt, washer, and wing nut kit 1 4 2350 459 Inlet filter 1 5+9* 2350 456 Inlet and outlet valve kit 1 6 2337 285 Feet 4 7 2337 288 Return tube/fitting 1 8 2337 290 Inlet valve tool 1 10 2351 007 1/4” X 10 m spray hose 1 * Wear parts: Not covered by guarantee Replacement parts available by calling customer service. 14 Airless Sprayer Plus AUS 2 years guarantee The guarantee runs for two years, counting from the date of sale (sales slip). It covers and is restricted to free-of-charge rectification of faults which are demonstrably attributable to the use of faulty materials in manufacture, or assembly errors; or free-of-charge replacement of the defective parts. The guarantee does not cover incorrect use or commissioning or fitting or repair work which is not stated in our operating instructions. Wearing parts are also excluded from the guarantee. The guarantee excludes commercial use. We expressly reserve the right to fulfil the guarantee. The guarantee expires if the tool is opened up by persons other than WAGNER service personnel. Transport damage, maintenance work and loss and damage due to faulty maintenance work are not covered by the guarantee. Under any guarantee claim, there must be proof of purchase of the tool through submission of the original receipt. Wherever legally possible, we exclude all liability for injury, damage or consequential loss, especially if the tool has been used for a purpose other than that stated in the operating instructions, commissioned or repaired other than in accordance with our operating instructions or if repairs are performed by someone who is unqualified. We reserve the right to perform any repairs in excess of those stated in our operating instructions. In case of guarantee or repair, please refer to your point of sale. Environmental protection The device and all accessories and packaging have to be re-used in an environmentally friendly manner. Do not dispose of the appliance with household waste. Support environmental protection by taking the appliance to a local collection point or obtain information from a specialist retailer. Leftover paint and solvents may not be emptied into drains, the sewage system or disposed of as household rubbish. It has to be disposed of separately as special waste. Please pay special attention to the instructions on the product packaging. Important Note regarding Product Liability! According to an EU directive, the manufacturer is only liable without limitation for faults in the product if all parts come from the manufacturer or have been approved by the manufacturer and have been mounted to the device and are operated properly. If third-party accessories or spare parts are used, the manufacturer is exonerated wholly or partly from his/her liability if use of the third-party accessories or spare parts have caused a defect in the product. 15 AUS 16 Airless Sprayer Plus Airless Sprayer Plus AUS 17 Airless Sprayer Plus AUS D J. Wagner GmbH Otto-Lilienthal-Str. 18 D-88677 Markdorf Hotline 0180 5 59 24 637 +49/ (0) 75 44/ 505-1169 B WSB Finishing Equipment Veilinglaan 56-58 1861 Meise-Wolvertem +32/2/2 69 46 75 +32/2/2 69 78 45 F Wagner France S.a.r.l. 12 Avenue des Tropiques Z.A. de Courtaboeuf 91978 Les Ulis Cedex 0 825 011 111 DK/S +33 (0) 1 69 81 72 57 Wagner Spraytech Scandinavia A/S Helgeshøj Allé 28 DK-2630 Tåstrup +45/43 27 18 18 +45/43 43 05 28 CH J. Wagner AG Industriestraße 22 9450 Altstätten +41/71/7 57 22 11 +41/71/7 57 23 23 SK E-Coreco SK s.r.o. Kráľovská ulica 8/7133 927 01 Šaľa Slovenská republika +421948882850 +421313700077 NL WSB Finishing Equipment BV De Heldinnenlaan 200 3543 MB Utrecht +31/30/2 41 41 55 +31/30/2 41 17 87 GB Wagner Spraytech (UK) Ltd. The Coach House 2 Main Road Middleton Cheney OX17 2ND 01295 714200 E-Coreco s.r.o. Na Roudné 102 301 00 Plzeň +420 734 792 823 +420 227 077 364 E Makimport Herramientas, S.L. C/ Méjico nº 6 Pol. El Descubrimiento 28806 Alcalá de Henares (Madrid) 902 199 021/ 91 879 72 00 91 883 19 59 SLO Adresa servisa: GMA Elektromehanika d.o.o. Cesta Andreja Bitenca 115, Ljubljana 1000/Slovenija +386(1)/583 83 04 +386(1)/518 38 03 H Magyarországi szerviz Hondimpex KFT. Kossuth L. u. 48-50 8060 Mór +36(-22)/407 321 +36(-22)/407 852 PL PUT Wagner Service ul. E. Imieli 27 41-605 Swietochlowice +48/32/2 45 06 19 +48/32/2 41 42 51 HR / AUS Adresa servisa: EL-ME-HO Horvatinčićev put 2 10436 Rakov Potok/Kroatien +385(-1)65 86 - 028 Wagner Spraytech Australia Pty. Ltd., 14-16 Kevlar Close, Braeside, VIC 3195/Australia +61/3/95 87 20 00 +61/3/95 80 91 20 www.wagner-group.com 01295 710100 Part. No. 2351213 11/2014_RS © Copyright by J.Wagner GmbH 18 CZ Not responsible for errors and changes.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project